HOME DECORATORS
collection
ARTISAN MLTMD CBNT W/GLS DRS
Assembly Instructions
HDC #: 08066 МЕС #:АТ7102
Please read over the instructions; 1t will be a time-saver
1n the long run.
Note: Before assembly, please be sure to work on a soft
flat surface to avoid any damage to the finish.
Page 1 - 11
Parts Check List
Please remove all the parts carefully from the box. Thoroughly
clean all wood surfaces to remove dust and dirt that may have
settled onto the finish.
(1) Top Panel - 1 (2) Bottom Panel - 1 3) Left Side Panel - 1
(4) Right Side Panel - 1 (5) Fixed Panel - 1 (6) Adjustable shelf -2
7
| | A
i |
Door - 2 (8) Drawer Face Panel-1 9) Drawer Back Panel-1
<—
10 Left Drawer Side Panel-1 1D Right Drawer Side Panel-1 12) Drawer Bottom Panel-1
Ш
//
и
DA
—
10 Back Panel-1
Page 2 - 11
Hardware Check List
Please take all the hardware listed below out of the hardware bag.
A “^^
Cam-Bolt - 4
в
Cam-Lock - 4
с
Соуег - 4
D Uy,
Wood Dowel - 12
(A8x30mm)
Eo
Glue - 1(25g)
Fr
Allen Wrench - 1
Gua
Allen Bolt - 8 (91/4"x1-1/4")
H e
Lock Washer - 8 (01/4")
I
Flat Washer - 8 (91/4"x16D)
Y
J 3
Drawer Hand Pull - 2
К «==
Long Bolt - 4(95/32"x5/8")
Вос
Shelf Support - 8
M %
Long Screw - 8
(#8x1")
N %
Round Head Screw - 30
(#6x 14mm)
Tilting Prevent Screw-1set
Page 3-11
When inserting cam-bolts, the shoulder should be flush with the
surface. If using an electric screwdriver, be careful not to over tighten
the Cam-bolt, this can cause damage .
Cam-bolt Cam-bolt not Flush
Flush
Shoulder
How to use Cam-Locks
Cam-locks should be inserted into their designated holes with the arrow
pointing to the nearest edge. The coordinating Cam-bolt will be
inserted into the Cam-lock. Using the allen wrench or a flat-head
screwdriver, tighten the Cam-locks until you feel resistance. Over
tightening the Cam-lock may break the cam-lock.
AllenWrench
Cam-bolt
Page 4 - 11
1. Fill the middle holes on Bottom Panel(2), Side Panel (3&4), and
Fixed Panel(5) 1/4 with Glue(E). Then insert Wood Dowels(D).
Screw Cam-bolts(A) into the threaded holes in Top Panel(1).
See figure below:
Page 5 -
11
2. Attach Bottom Panel(2) and Fixed Panel(5) to Side Panel(3&4)
with Allen Bolts(G) through Lock Washers(H) and Flat Washers(1)
by Allen Wrench(F).
3. Afttach Top Panel(1) to Side Panels(3&4) with Cam-locks(B) by
Allen Wrench(F). Cover all Cam-Locks(B) with Covers(C).
See figure below:
Page 6 - 11
9. Attach the drawer as figure shows.
Install the Hand Pull(J) to the drawer face with Blot(K) by screwdriver.
See figure below:
Page 7- 11
5. Place Shelf Support(L) into the holes on Side Panel(3&4).
Place Adjustable Shelf(6) onto the Supports(L).
See figure below:
©
7
\
Page 8 - 11
6. Attach the glide Door(7) to the groove.
See figure below.
e
Page 9 - 11
7. Before attaching back panel, be sure the space around the doors are
even. If not even, shift the unit either right or left, whichever
needed. Then attach the Back Panel (10) with Round Head
Screw(N).
See figure below:
/
/
/
/
/
/
Page 10-11
8. Tip prevention hardware 1s included to attach the item to the wall.
See figure below:
Wall
\
\
>
. ‘ a“
—
ПИШИ,
Assembly 1s now complete!
Page 11 - 11
">
