King Electric PSH1215T Installation Guide

 SAVE THESE INSTRUCTIONS
INSTALLATION AND MAINTENANCE
100 BTU
Model# PSH1215T ua” 15000
Y 120V-60Hz
Yellow Jacket Mini A 12 5A
foot
6 CFM
OD.
ELECTRIC SHOCK OR FIRE HAZARD
READ ALL WIRE SIZING, VOLTAGE REQUIREMENTS AND SAFETY DATA
TO AVOID PROPERTY DAMAGE AND PERSONAL INJURY
READ CAREFULLY - Use the heater only as described in this manual. Any other use is not recommended and could result in fire, electric shock, and personal
injury. Following these instructions will prevent difficulties that might occur during the installation and use of the heater. Please study the instructions first, as
they may save considerable time and trouble during use addition to providing important safety information. Make sure to save these instructions for future use.
NEVER LEAVE HEATER UNATTENDED WHILE CONNECTED TO A POWER SOURCE
A WARNING FIRE OR EXPLOSION MAY OCCUR! Heater has hot arching or sparking parts. Do not use it in areas where gasoline, paint, or
flammable liquids are used.
AN WARNING RISK OF FIRE. To prevent possible fire, Don't block intakes or exhaust in any manner. Don't use on soft surfaces, like a bed
where openings may become blocked. Heater must be kept clear of all obstructions. Maintain a 3 foot min. clearance from front
and 12 inches from sides and rear. Heaters must be kept clean of lint, dirt, and debris (See maintenance instructions on page 2)
AN WARNING RISK OF FIRE. Do Not use heater with extension cord. Plug the heater directly into a 120VAC receptacle.
AN WARNING RISK OF FIRE. Do not use as a residential or household heater.
AN WARNING BURN HAZARD. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles
when moving the heater.
AN WARNING RISK OF ELECTRIC SHOCK OR INJURY. Do not run cord under carpeting, Do not cover cord with throw rugs, runners or similar
coverings. Do not route cord under furniture or appliances. Arrange cord away from the traffic area where it will not cause a
tripping hazard. Do not operate any heater with a damaged cord or plug, or after heater malfunctions, or has been dropped or
damaged in any manner. Discard heater, or call King Electrical Mfg. 206-762-0400 for examination and/or repair.
AN WARNING RISK OF ELECTRICAL SHOCK. Connect to properly grounded outlets only. Do not insert or allow foreign objects to enter any
ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater. Unplug heater before perform-
ing any maintenance or when not in use. To disconnect heater, turn control to low, then remove plug from outlet.
CAUTION—RISK OF ELECTRIC SHOCK
DO NOT OPEN HEATER SHELL
NO USER—SERVICEABLE PARTS INSIDE
KING ELECTRIC MFG CO - 9131 10TH AVENUE SOUTH - SEATTLE, WA 98108 - PH:206 762 0400 - FAX: 206 763 7738 - www.king-electric.com
SAVE THESE INSTRUCTIONS
AN WARNING Never leave heater unattended while connected to a power source.
A WARNING CAUTION! Hot while in operation. Do not touch. Keep children, animals, clothing and combustibles away from heater.
AN WARNING Read all instructions before using this heater. A WARNING Risk of electric shock!
e Use extreme caution when used by or near children or invalids. e Avoid using an extension cord because the extension cord may
e Do not use outdoors. overheat and cause a risk of fire. However, if you have to use an
e This heater is not intended for use in bathrooms, laundry areas and extension cord; use only a 14 AWG or better extension cord.
similar indoor locations. Never locate heater where it may fall into a e ALWAYS use only the electrical power (voltage and frequency)
bathtub or other water locations. specified on the model plate of the heater.
e Do not use heater in wet or moist locations. o ALWAYS use only three-prong, ground outlet and extension cord.
e ALWAYS unplug the heater when not in use.
e Always locate heater on a stable and level surface.
Keep all combustible materials away from this heater.
e Do not place the heater against curtains, drapes, paperboard, or any
other low-density fiberboard surfaces.
OPERATION INSTRUCTIONS
Position the fan heater so that it stands upright on a firm, level Automatic Overheat Safety Control
surface and at a safe distance from wet environments and e This heater is equipped with an internal heat limiting thermostat
flammable objects.
Connect the fan heater to the proper electrical power outlet.
Set the thermostat dial to the maximum temperature.
and overheat protection circuit. When a potential overheat
temperature is reached, the system will automatically shut the
The fan heater will switch on when the ON/OFF switch is heater off.
set to the ON position Thermostat Instructions
e Set the thermostat to “+” and let the heater operate with full
Setting Function power input. When the room temperature reaches the required
O Unit is Off value, turn the thermostat to the left until it switches off.
| Fan Runs - Full Power Heating
e The thermostat will then switch on and off automatically to control
Once the room reaches the desired temperature, turn the the room the room temperature according to the preset value and
thermostat dial back until heating element turns off.
keep the room temperature constant.
CLEANING AND MAINTENANCE
Before cleaning the appliance, disconnect it from the outlet and let it cool down.
e The enclosure is easy to get dirty. Wipe it often with a soft sponge. For very dirty parts, wipe with a sponge dipped in < 122°F water and
mild detergent, then dry the heater enclosure with a clean cloth. Be careful not to let the water enter the inside of the appliance.
e Inorder to protect the enclosure, do not splash water onto the heater, and never use a solvent like gasoline, isoamyl acetate, toluene, etc. to
the clean the heater.
TROUBLE SHOOTING
Problem Cause Solution
Heating element does not glow red. Stainless steel elements won’t glow red to produce heat. Heater is operating correctly.
1. Check power connections/connect heater to power supply. 2.
No power to heater. Make sure On/Off switch is turned to ON.
Thermostat will shut off once desired room temperature is reached.
Desired room temperature reached
Heater is operating correctly.
Do not feel heat or air flow.
Heater does not heat area in front of heater only, it will
Heater is operating correctly.
disperse heat throughout room to heat entire space. p y у
Auto-Reset has tripped. Unplug heater, allow to cool down for 10 minutes. Then restart.
KING ELECTRIC MFG CO - 9131 10TH AVENUE SOUTH - SEATTLE, WA 98108 - PH:206 762 0400 - FAX: 206 763 7738 - www.king-electric.com