2-23-11 Draft

Installation Manual for

Cisco IPTV Receivers for use with your AT&T U-verse TV service

Model ISB7005

2

2-23-11 Draft

Contents

IMPORTANT SAFETY INSTRUCTIONS .............................................................................4

Change the Way You Watch TV ..........................................................................................6

What’s In the Carton? ..........................................................................................................6

Safety First ..........................................................................................................................6

Identify Your Receiver with the Serial Number ....................................................................6

In This Manual .....................................................................................................................6

Questions About Your Service. ............................................................................................6

Protecting You and the Environment ...................................................................................7

Front Panel ..........................................................................................................................8

Back Panel ..........................................................................................................................9

ISB7005 Wireless Network Connection.............................................................................10

Connecting to the In-Home Network .................................................................................11

Connections for a High-Defi nition TV (HDTV) ...................................................................12

Connections for a Standard-Defi nition TV (SDTV) ............................................................13

Connections for a VCR or DVD Recorder .........................................................................14

Connecting an Over-the-Air Converter Box .......................................................................14

Connecting to an HDTV with an HDMI Connector ............................................................15

Connecting to an HDTV with a DVI Connector..................................................................16

Connecting to an HDTV with Component (YPbPr) Connectors ........................................17

Connecting to an SDTV with Component (YPbPr) Connectors.........................................18

Connecting to an SDTV with an S-Video Connector .........................................................19

Connecting to an SDTV with an RCA-Type Connector .....................................................20

Connecting to an SDTV with a Coaxial Cable ...................................................................21

Connecting to a Home Theater System with Component (YPbPr) Connectors ................22

Connecting to a Stereo VCR or DVD Recorder (optional).................................................23

Troubleshooting .................................................................................................................24

Avoid Screen Burn-In ........................................................................................................24

Frequently Asked Questions..............................................................................................25

Picture Formats .................................................................................................................26

Index ..................................................................................................................................27

Compliance Information.....................................................................................................29

3

Notice for Installers

2-23-11 Draft

The servicing instructions in this notice are for use by qualifi ed service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions, unless you are qualifi ed to do so.

Note to System Installer

For this apparatus, the cable shield/screen shall be grounded as close as practical to the point of entry of the cable into the building. For products sold in the US and Canada, this reminder is provided to call the system installer's attention to

Article 800-93 and Article 800-100 of the NEC (or Canadian

Electrical Code Part 1), which provides guidelines for proper grounding of the cable shield.

CAUTION: To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Refer servicing to qualified service personnel.

WARNING

TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS UNIT TO RAIN OR MOISTURE.

4

This symbol is intended to alert you that uninsulated voltage within this product may have sufficient magnitude to cause electric shock.Therefore, it is dangerous to make any kind of contact with any inside part of this product.

Ce symbole a pour but d’alerter toute personne qu’un contact avec une pièce interne de ce produit, sous tension et non isolée, pourrait être suffisant pour provoquer un choc

électrique. Il est donc dangereux d’être en contact avec toute pièce interne de ce produit.

This symbol is intended to alert you of the presence of important operating and maintenance (servicing) instructions in the literature accompanying this product.

Ce symbole a pour but de vous avertir qu’une documentation importante sur le fonctionnement et l’entretien accompagne ce produit.

20080814_Installer800

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

Power Source Warning

A label on this product indicates the correct power source for this product. Operate this product only from an electrical outlet with the voltage and frequency indicated on the product label. If you are uncertain of the type of power supply to your home or business, consult your service provider or your local power company.

The AC inlet on the unit must remain accessible and operable at all times.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Ground the Product

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifi ers) that produce heat.

9) Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fi t into your outlet, consult an electrician for replacement of the obsolete outlet.

WARNING: Avoid electric shock and fi re hazard! If this product connects to cable wiring, be sure the cable system is grounded (earthed). Grounding provides some protection against voltage surges and built-up static charges.

Protect the Product from Lightning

In addition to disconnecting the AC power from the wall outlet, disconnect the signal inputs.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

Verify the Power Source from the

On/Off Power Light

When the on/off power light is not illuminated, the apparatus may still be connected to the power source. The light may go out when the apparatus is turned off, regardless of whether it is still plugged into an AC power source.

Eliminate AC Mains Overloads

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualifi ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as a power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

WARNING: Avoid electric shock and fi re hazard! Do not overload AC mains, outlets, extension cords, or integral convenience receptacles. For products that require battery power or other power sources to operate them, refer to the operating instructions for those products.

IMPORTANT SAFETY INSTRUCTIONS,

continued

Handling Disposable Batteries

This product may contain disposable batteries. Heed the following warning and follow the Battery Safety and Battery Disposal instructions below.

Protect from Exposure to Moisture and Foreign Objects

WARNING: Avoid electric shock and fi re hazard! Do not expose this product to dripping or splashing liquids, rain, or moisture. Objects fi lled with liquids, such as vases, should not be placed on this apparatus.

WARNING: There is danger of explosion if the battery is mishandled or incorrectly replaced. Replace only with the same type of battery. Do not disassemble it or attempt to recharge it outside the system. Do not crush, puncture, dispose of in fi re, short the external contacts, or expose to water or other liquids. Dispose of the battery in accordance with local regulations and instructions from your service provider.

Battery Safety

• Insert batteries correctly. There may be a risk of explosion if the batteries are incorrectly inserted.

• Do not attempt to recharge ‘disposable’ or ‘non-reusable’ batteries.

• Please follow instructions provided for charging ‘rechargeable’ batteries.

• Replace batteries with the same or equivalent type that we recommend.

• Do not expose batteries to excessive heat (such as sunlight or fi re).

• Do not expose batteries to temperatures above 100°C (212°F).

Battery Disposal

• The batteries may contain substances that could be harmful to the environment.

• Recycle or dispose of batteries in accordance with the battery manufacturer’s instructions and local/national disposal and recycling regulations.

• The batteries may contain perchlorate, a known hazardous substance, so special handling and disposal of this product might be necessary. For more information about perchlorate and best management practices for perchlorate-containing substance, see

www.dtsc.ca.gov/hazardouswaste/perchlorate

Provide Ventilation and

Select a Location

• Remove all packaging material before applying power to the product.

• Do not place this apparatus on a bed, sofa, rug, or similar surface.

• Do not place this apparatus on an unstable surface.

• Do not install this apparatus in an enclosure, such as a bookcase or rack, unless the installation provides proper ventilation.

• Do not place entertainment devices (such as VCRs or DVDs), lamps, books, vases with liquids, or other objects on top of this product.

• Do not block ventilation openings.

WARNING: Avoid electric shock and fire hazard!

Unplug this product before cleaning. Do not use a liquid cleaner or an aerosol cleaner. Do not use a magnetic/static cleaning device (dust remover) to clean this product.

WARNING: Avoid electric shock and fi re hazard! Never push objects through the openings in this product. Foreign objects can cause electrical shorts that can result in electric shock or fi re.

Service Warnings

WARNING: Avoid electric shock! Do not open the cover of this product. Opening or removing the cover may expose you to dangerous voltages. If you open the cover, your warranty will be void. This product contains no user-serviceable parts.

Check Product Safety

Upon completion of any service or repairs to this product, the service technician must perform safety checks to determine that this product is in proper operating condition.

Protect the Product When Moving It

Always disconnect the power source when moving the apparatus or connecting or disconnecting cables.

20090915_IP_NoTuner_Safety

5

6

2-23-11 Draft

Change the Way You Watch TV

2-23-11 Draft

Welcome to U-verse TV. The ISB7005 devices, known as U-verse receivers, bring a rich, new set of interactive services directly to you through your TV and your in-home IP network. The receiver uses wireless technology 802.11n to connect to the network.

The ISB7005 receiver allows for easy and secure connection to U-verse services. The signal strength indicator on the front panel of the receiver identifi es the strength of the wireless connection and aids in the proper placement of the receiver.

What’s In the Carton?

In addition to this installation manual, the receiver carton contains the following items:

• An ISB7005 Receiver - A wireless receiver

• A power cord and power adapter

Other equipment may be required.

Safety First

Before using the receiver, read the Important Safety Instructions section of this manual.

Identify Your Receiver with the Serial Number

At times your service provider may ask for the serial number. To fi nd the serial number for your receiver, look on the bottom of the receiver for the label. The serial number is a 9-digit numeric code to the right of the letters “S/N” on the label.

Use the space provided here to record the serial number: _________________________________

In This Manual

This manual covers the information you need to connect your receiver to both your in-home IP network and your entertainment system. The manual also outlines certain safeguards and installation information.

The safety information contained in this manual was developed and provided solely by the receiver manufacturer, Cisco Systems, Inc.

Questions About Your Service

For questions about how to operate your receiver, once installed, refer to your Feature Guide available for download at: uverse.att.com/support. For all other questions about your TV service, contact your service provider.

Protecting You and the Environment

Cisco addresses the environmental impact of networking products throughout their lifecycle, from product development, manufacturing, and use to service and end-of-life. Integrating environmental policies into

Cisco engineering and manufacturing practices results in socially accountable business practices that help reduce the environmental impact associated with networking products.

7

8

Front Panel

2-23-11 Draft

LINK HD RECORD MENU

1

ISB7005

2

1 Power

3 4 5 6 7 8 9 10 11

T14820

Turns the receiver on or places it in standby. To restart the receiver, press and hold the POWER button for 10 seconds. The LED is green

Indicator

4 Link

5 HD

6 Record

Indicates network link status. The LED is green

Indicates the set-top is set to a resolution of 720p, 1080i, or 1080p. The

LED is blue

8 Menu

10 OK

Indicates that a recording is in progress. The LED is red

Receives the infrared signal from the remote control. The sensor is behind the front panel

Accesses the on-screen menu

Accesses on-screen services (such as the on-screen guide, video-on- demand, or pay-per-view) and navigates menus

Selects the current item

11 USB Port USB connector. (Reserved for future use)

Note: This illustration may vary from the actual product.

Back Panel

Pb Y

2-23-11 Draft

L R

TO TV

(VIDEO OUT)

1

NETWORK

2

OPTICAL USB POWER

Pr

S-VIDEO

VIDEO

OUT

AUDIO

OUT

3 4 5 6 7

8

9 10

1 To TV (Video Out)

2 Network

3 YPbPr

4 S-Video

Connect to TV. You must set the channel on your TV to the channel designated by your service provider (usually channel 3). Contact your service provider for the channel information

Connect to the Ethernet (CAT-5) network at your home, if applicable

Connect the receiver to the component video input (YPbPr) on the

HDTV. See pages 11 and 12 for more information

Connect an S-Video cable to send an S-Video signal to your TV, VCR, or

DVD recorder. This signal is standard-defi nition but higher quality than information

Connect to composite input on your HDTV or SDTV

6 Audio Out (L/R)

is connected to the TV, and the other output is used to connect to a home theater system, DVD recorder, or VCR

Connect RCA-type cables to Audio Out to send analog audio signals

(left and right) to a TV with stereo inputs or to a stereo amplifi er

Note: Two sets of audio out connectors are provided. Typically, one set of outputs is connected to the TV, and the other set is used to connect to a home theater system, DVD recorder, or VCR

7 Optical

8 HDMI

Connect an optical cable to send a digital audio signal to a surround- sound receiver or other digital audio device

Connect an HDTV HDMI

™

(High-Defi nition Multimedia Interface) cable from the HDTV to the HDMI port. HDMI supports both digital audio and

USB connector. (Reserved for future use)

10 Power Connect the DC output of the AC power adapter (provided) to deliver power to the receiver

Note: This illustration may vary from the actual product.

9

10

Connecting the Receiver

2-23-11 Draft

To connect your receiver to your network and home entertainment devices, complete these steps.

1

Because the connections for a high-defi nition (HD) or standard-defi nition (SD)

TV are different, you must determine if your TV is HD

9

16 or 3

or SD. Your TV must receive HD signals for you to enjoy the benefi ts of HDTV. Refer to the manual that came with your TV for more information.

See page 26 for more information on picture formats.

4

2

3



4

Make one of the following connections for your home network:

• If your home network uses coaxial cable, use the TO WALL connector on the receiver. See page 11.

• If your home network uses twisted pair cable (phoneline wiring), use the TO

WALL connector on the receiver and an adapter that converts twisted pair to coaxial. See page 11.

• If your home network uses Ethernet (CAT-5) cable, use the NETWORK connector on the receiver. See page 11.

Make the connections for your TV, VCR, and DVD recorder as follows:

• If you are using an HDTV, see page 12 and the connection diagrams in this

manual.

• If you are using a standard-defi nition TV, see page 13 and the connection

diagrams in this manual.

• If you want to record some programs on VCR tape or DVD, see page 14

and the connection diagrams in this manual.

Identify the additional consumer electronic devices you will connect to the receiver and TV.

See pages 15 through 23 and refer to the owner’s manual for the device.

VCR DVD

Home Theater

Other

Plug the receiver and the TV into an AC power source that is not controlled by a switch. For further instructions on completing your setup, refer to the Feature

Guide available from your service provider.

5

ISB7005 Wireless Network Connection

2-23-11 Draft

The ISB7005 receiver allows for easy and secure connection to U-verse services. The signal strength indicator on the front panel of the receiver identifi es the strength of the wireless connection and aids in the proper placement of the receiver.

ISB

7005

Signal Strength

Indicator

LINK HD RECORD MENU

Wireless

LEDs Receiver Operational Status

This indicates the wireless signal is excellent. The video quality is good.

T14822

This indicates the wireless signal is very good. The video quality is good.

This indicates the wireless signal is good. The video quality is good. You must obtain

three or more green bars at initial installation.

This indicates the wireless signal is fair. The video quality is good.

This indicates the wireless signal is weak. The video quality may be poor. The STB

should be re-oriented to achieve a better wireless signal.

This indicates the wireless signal is very weak. No video can be displayed. The receiver must be re-oriented to achieve a better wireless signal.

This indicates the STB Ethernet port is connected with the residential gateway through the Ethernet cable.

11

12

Connections for a High-Defi nition TV (HDTV)

2-23-11 Draft

To use the receiver with an HDTV, you must make one of the following connections to view the HD content. Refer to the owner’s manual for your TV and the cabling diagrams in this manual for more detailed connection information.

Although all connections provide you with quality service, we list the connections in our recommended order.

Notes:

• The labeling on your receiver or HDTV may vary slightly from the illustrations shown below.

• Some cables shown in the connection diagrams may not be included with this receiver.

• Set the HD mode and select the output video format (480i, 720p, 1080i, or 1080p) on the receiver

using the instructions provided in the Feature Guide available for download at: uverse.att.com/support

HDTV

Connections

Use One of These Required Connections to an HDTV

Some HDTVs have a High-Defi nition Multimedia

Interface (HDMI) connector. The HDMI connector provides both a digital video and audio connection.

See the connection diagram on page 15 for an example.

Note: The HDMI port on the TV must support high-bandwidth digital content protection (HDCP).

The HDMI connector can provide the connection to an HDTV with a DVI input. If your HDTV has a

Digital Visual Interface (DVI) connector, you need an HDMI-to-DVI adapter, and a separate audio connection (either L/R or optical audio).

Note: The DVI port on the TV must support high-bandwidth digital content protection (HDCP).

See the connection diagram on page 16 for an example.

The YPbPr (red, blue, and green) connectors provide high-defi nition component video signals to an HDTV, and a separate audio connection

(either L/R or optical audio).

See the connection diagram on page 17 for an example.

Receiver

Connections

Adapter Needed

L R

AUDIO

OUT

OPTICAL

Pb Y

L R

AUDIO

OUT

DVI

L R

OPTICAL

INPUT

Y

Pb

Pr

L R

Some HDTVs have only RGB or RGB-HV connectors. If you have one of these HDTVs, you need a Component-to-RGB adapter, and you need a separate audio connection.

OPTICAL

Pb Y

R

G

B

OPTICAL

INPUT

H

V

P

Adapter Needed

L R

AUDIO

OUT

L R

Connections for a Standard-Defi nition TV (SDTV)

2-23-11 Draft

When using the receiver with an SDTV, you must make one of the following connections to view content. Some SDTVs may not have all these connections. Refer to the owner’s manual for your TV and the cabling diagrams in this manual for more detailed information.

Although all connections provide you with quality service, we list the connections in our recommended order.

Notes:

• The labeling on your receiver or SDTV may vary slightly from the illustrations shown below.

• Some cables shown in the connection diagrams may not be included with this receiver.

Use One of These Required Connections to an SDTV

The YPbPr (red, blue, and green) connectors can provide standard-defi nition component video signals to an SDTV. A separate audio connection is also needed.

Receiver

Connections

Pb Y

Pr

SDTV

Connections

Y

Pb

Pr

L

AUDIO

OUT

R

L R

The S-Video connection provides an optimal video connection to SDTVs. A separate audio connection is also needed.

See the connection diagram on page 19 for an example.

S-VIDEO S-VIDEO

IN

L

AUDIO

OUT

R

L R

The Video Out connector provides a video connection to an SDTV. A separate audio connection is also needed.

See the connection diagram on page 20 for an example.

VIDEO

OUT

VIDEO

IN

L R

AUDIO

OUT

L R

The To TV (Video Out) connector provides both a video and audio connection to an SDTV.

See the connection diagram on page 21 for an example.

TO TV

(VIDEO OUT)

CABLE IN/

ANT IN

13

14

Connections for a VCR or DVD Recorder

2-23-11 Draft

When using the receiver with a VCR or DVD recorder, you must make one of the following connections to view content.

Although all connections provide you with quality service, we list the connections in our recommended order.

Notes:

• The labeling on your receiver, VCR, or DVD recorder may vary slightly from the illustrations shown

below.

• Some cables shown in the connection diagrams may not be included with this receiver.

Use One of These Optional Connections to a VCR or DVD Recorder

For VCRs or DVD recorders with S-Video In and Left and Right audio connectors, use the

S-Video and the Audio Out Left and Right connectors on the receiver.

Receiver

Connections

S-VIDEO

VCR/DVD Recorder

Connections

S-VIDEO

IN

L R

AUDIO

OUT

L R

For VCRs or DVD recorders with Video In and

Left and Right audio connectors, use the Video

Out and the Audio Out connectors (Left and

Right) on the receiver.

See the connection diagram on page 23 for an example.

VIDEO

OUT

VIDEO

IN

L R

AUDIO

OUT

L R

Connecting an Over-the-Air Converter Box

You can connect an over-the-air converter box directly to your TV to receive certain local channels, but do not connect the over-the-air converter box directly to your receiver.

Connecting to an HDTV with an HDMI Connector

2-23-11 Draft

Cable Used in this Confi guration

• 1 HDMI Cable

Notes:

• The HDMI port on the TV must support high-bandwidth digital content protection (HDCP).

• The HDMI interface supports Dolby ™ Digital 5.1 audio.

WARNING:

Electric shock hazard! Unplug all electronic devices before connecting or disconnecting any device cables to the receiver.

Receiver

TO TV

(VIDEO OUT)

NETWORK

Pb Y L R

Pr

S-VIDEO

VIDEO

OUT

AUDIO

OUT

OPTICAL USB POWER

Back of HDTV

S-VIDEO

VIDEO

L/

MONO

AUDIO

R

IN

AUDIO

CENTER

CHANNEL IN

HDMI

ON OFF

AUDIO IN

DVI/HDCP

R L

Y

P

B

L

P

R

AUDIO

R

HD 1

IN

ANT (75 )

VIDEO

L/

MONO

R

OUT

Y

P

B

L

ANT-1

P

R

AUDIO

R

OUT

HD 2

IN

ANT-2

T14823

15

16

Connecting to an HDTV with a DVI Connector

2-23-11 Draft

Cables Used in this Confi guration

• 1 HDMI-to-DVI Cable or 1 HDMI Cable and 1 HDMI-to-DVI Adapter

• 1 Audio Left/Right Cable (You can also use an optical cable [indicated by the dotted line]

instead of the Audio Left/Right Cable as shown in the diagram, dependent upon your TV’s

capabilities.)

Notes:

• The DVI port on the TV must support high-bandwidth digital content protection (HDCP).

• When you connect the HDMI connector to the DVI connector on your HDTV, you need an

HDMI-to-DVI adapter and a separate audio connection.

WARNING:

Electric shock hazard! Unplug all electronic devices before connecting or disconnecting any device cables to the receiver.

Receiver

TO TV

(VIDEO OUT)

NETWORK

Pb Y L R

Pr

S-VIDEO

VIDEO

OUT

AUDIO

OUT

OPTICAL USB POWER

OR

Back of HDTV

S-VIDEO

VIDEO

L/

MONO

AUDIO

R

IN

AUDIO

CENTER

CHANNEL IN

DVI/HDCP

IN

ON OFF

AUDIO IN

DVI/HDCP

R L

OPTICAL

INPUT

Y

P

B

L

P

R

AUDIO

R

HD 1

IN

ANT (75 )

VIDEO

L/

MONO

R

OUT

Y

P

B

L

ANT-1

P

R

AUDIO

R

OUT

HD 2

IN

ANT-2

T14824

Connecting to an HDTV with Component (YPbPr) Connectors

2-23-11 Draft

Cables Used in this Confi guration

• 1 Component Video Cable (YPbPr)

• 1 Audio Left/Right Cable (You can also use an optical cable [indicated by the dotted line]

instead of the Audio Left/Right Cable as shown in the diagram, dependent upon your TV’s

capabilities.)

WARNING:

Electric shock hazard! Unplug all electronic devices before connecting or disconnecting any device cables to the receiver.

Receiver

TO TV

(VIDEO OUT)

NETWORK

Pb Y L R

Pr

S-VIDEO

VIDEO

OUT

AUDIO

OUT

OPTICAL USB POWER

OR

Back of

HDTV

S-VIDEO

VIDEO

L/

MONO

AUDIO

R

IN

AUDIO

CENTER

CHANNEL IN

HDMI

ON OFF

AUDIO IN

DVI/HDCP

R L

OPTICAL

INPUT

Y

P

B

L

P

R

AUDIO

R

HD 1

IN

ANT (75 )

VIDEO

L/

MONO

R

OUT

Y

P

B

L

ANT-1

P

R

AUDIO

OUT

R

HD 2

IN

ANT-2

T14825

17

18

Connecting to an SDTV with Component (YPbPr) Connectors

2-23-11 Draft

Cables Used in this Confi guration

• 1 Component Video Cable (YPbPr)

• 1 Audio Left/Right Cable

Note: The receiver must be set to the proper standard-defi nition mode.

WARNING:

Electric shock hazard! Unplug all electronic devices before connecting or disconnecting any device cables to the receiver.

Receiver

TO TV

(VIDEO OUT)

NETWORK

Pb Y L R

Pr

S-VIDEO

VIDEO

OUT

AUDIO

OUT

OPTICAL USB POWER

Y

P

B

P

R

VIDEO

IN

L R

AUDIO

IN

VIDEO

OUT

Back of SDTV

CABLE IN/

ANT IN

L R

CABLE OUT/

ANT OUT

AUDIO

OUT

T14826

Connecting to an SDTV with an S-Video Connector

2-23-11 Draft

Cables Used in this Confi guration

• 1 S-Video Cable

• 1 Audio Left/Right Cable

WARNING:

Electric shock hazard! Unplug all electronic devices before connecting or disconnecting any device cables to the receiver.

Receiver

TO TV

(VIDEO OUT)

NETWORK

Pb Y L R

Pr

S-VIDEO

VIDEO

OUT

AUDIO

OUT

OPTICAL USB POWER

L R

S-VIDEO

IN

VIDEO

IN

AUDIO

IN

VIDEO

OUT

L

Back of SDTV

CABLE IN/

ANT IN

R

AUDIO

OUT

CABLE OUT/

ANT OUT

T14827

19

20

Connecting to an SDTV with an RCA-Type Connector

2-23-11 Draft

Cables Used in this Confi guration

• 1 RCA-type Video Cable

• 1 Audio Left/Right Cable

WARNING:

Electric shock hazard! Unplug all electronic devices before connecting or disconnecting any device cables to the receiver.

Receiver

TO TV

(VIDEO OUT)

NETWORK

Pb Y L R

Pr

S-VIDEO

VIDEO

OUT

AUDIO

OUT

OPTICAL USB POWER

Y

PB

PR

L R

VIDEO

IN

AUDIO

IN

VIDEO

OUT

L

Back of SDTV

CABLE IN/

ANT IN

R

AUDIO

OUT

CABLE OUT/

ANT OUT

T14828

Connecting to an SDTV with a Coaxial Cable

2-23-11 Draft

Cable Used in this Confi guration

• 1 Coaxial Cable

Note: You must set the channel on your TV to the channel designated by your service provider

(usually channel 3). Contact your service provider for the channel information.

WARNING:

Electric shock hazard! Unplug all electronic devices before connecting or disconnecting any device cables to the receiver.

Receiver

Pb Y L R

TO TV

(VIDEO OUT)

Y

PB

PR

L R

VIDEO

IN

AUDIO

IN

OPTICAL

NETWORK

Coaxial

Cable

Pr

S-VIDEO

VIDEO

OUT

AUDIO

OUT

VIDEO

OUT

L

Back of SDTV

CABLE IN/

ANT IN

R

AUDIO

OUT

CABLE OUT/

ANT OUT

USB POWER

T14829

21

22

Connecting to a Home Theater System with Component (YPbPr) Connectors

Cables Used in this Confi guration

• 1 Component Video Cable (YPbPr)

• 1 Audio Left/Right Cable (You can also use an optical cable [indicated by the dotted line] instead

of the Audio Left/Right Cable as shown in the diagram.)

Notes:

• This connection requires that audio is provided by the home theater system.

• Consult the user guide that came with your home theater system for information on connecting your

other video and audio devices.

Contact AT&T ConnecTech

®

service to learn about affordable fl at-rate home theater installation services.

Call (800) 344-1734 to speak with an AT&T ConnecTech Representative. (Not available in all areas; See offers and terms & conditions at www.att.com/ConnecTech).

WARNING:

Electric shock hazard! Unplug all electronic devices before connecting or disconnecting any device cables to the receiver.

Receiver

TO TV

(VIDEO OUT)

NETWORK

Pb Y L R

Pr

S-VIDEO

VIDEO

OUT

AUDIO

OUT

OPTICAL

OR

DIGITAL

AUDIO

1

2

TV/CABLE

S-VIDEO

VIDEO

3

L

4

AUDIO

R

DVD

S-VIDEO

VIDEO

L

AUDIO

R

VIDEO 1

S-VIDEO S-VIDEO

VIDEO VIDEO

L

AUDIO

IN

R

L

AUDIO

OUT

R

Back of Home

Theater Receiver

COMPONENT VIDEO

Y Y Y

MONITOR

P

B

P

R

1

IN

2

P

B

P

R

OUT

P

B

P

R

S-VIDEO

OUT

VIDEO OUT

USB POWER

T14830

Connecting to a Stereo VCR or DVD Recorder (optional)

2-23-11 Draft

The diagram below shows how to connect a recording device to your receiver. Although it is possible to watch TV using a connection through your VCR or DVD recorder to the TV, this connection may not provide the best picture, and HDTV users are restricted to an SD format. In addition, some content is copy protected and passing this content through the recording device may result in a picture that cannot be viewed.

For these reasons, the connection shown is best used to provide only video and audio to your recording device and not for normal TV viewing. The connection from the recording device to the TV (only used for playback of recorded material) depends on the type of device being used, the outputs that are supported, and the inputs that remain available for use on your TV.

Consult the owner’s manuals provided with your TV and recording device for more details on connection options.

Cables Used in this Confi guration

• 1 RCA-type Video Cable

• 1 Set Audio Left/Right Cables

WARNING:

Electric shock hazard! Unplug all electronic devices before connecting or disconnecting any device cables to the receiver.

Connecting your TV directly to the Audio/Video output of your receiver will assure a more vivid picture and enhance your viewing enjoyment.

Receiver

TO TV

(VIDEO OUT)

NETWORK

Pb Y L R

Pr

S-VIDEO

VIDEO

OUT

AUDIO

OUT

OPTICAL USB POWER

L R

VIDEO

IN

AUDIO

IN

Back of Stereo VCR or DVD Recorder

CABLE IN/

ANT IN

L R

VIDEO

OUT

AUDIO

OUT

CABLE OUT/

ANT OUT

T14831

23

24

Troubleshooting

2-23-11 Draft

If the receiver does not perform as expected, the following tips may help. If you need further assistance, contact your service provider.

No Picture

• Verify that the power to your TV is turned on.

• If the receiver is plugged into a wall switch, verify that the switch is in the ON position.

• Verify that all cables are properly connected.

• If your system includes a VCR, DVD recorder, or stereo, verify that you have properly connected the device to the receiver.

• Verify that you are using the proper input selection to the home theater receiver or TV.

• Verify that the receiver is set to the proper screen type and resolution.

• If you are using coaxial cable to connect to your TV, verify that the TV is tuned to the channel designated by your service provider (usually channel 3). Contact your service provider for the channel information.

No Color or Incorrect Color

• Verify that the current TV program is broadcast in color.

• Adjust the TV color controls.

• If you are using a component video connection (YPbPr), check that all connectors are completely and properly plugged into the receiver and TV.

• If you are using a component video connection (YPbPr) and your HDTV has only RGB or RGB-HV connectors, you must use an adapter. You can obtain the adapter through an electronic parts retailer.

No Sound

• If your setup includes a VCR, DVD recorder, or stereo, verify that you have properly connected the device to the receiver.

• Verify that the volume is turned up.

• Verify that the mute function is not on.

• Verify the proper input selection to the home theater receiver or TV.

• If you are using coaxial cable to connect to your TV, verify that the TV is tuned to the correct channel.

Avoid Screen Burn-In

Images such as letterbox bars or side bars, bright closed-captioning backgrounds, station logos, or any other stationary images may cause the display in your HDTV to age unevenly; this is known as screen burn-in. Refer to the owner’s manual that came with your HDTV for more information.

CAUTION:

Avoid screen burn-in.

Do not display the same fi xed images on your HDTV screen for extended periods of time.

Frequently Asked Questions

2-23-11 Draft

What Is Digital Television?

Digital television (DTV) is a huge leap forward in television technology compared to analog television that has been widely available since the 1940s. DTV is delivered and displayed using digital encoding, similar to the way a PC operates. By using digital technology, there is no variation in picture and sound quality from the origination point until it is displayed on your television. You always receive a high-quality picture without the wavy lines or static you might sometimes get from a weak analog signal. Another feature of digital television is digital surround sound using Dolby Digital technology, which is the same technology used to produce the sound you hear in movie theaters.

What Is Standard-Defi nition Television?

Standard-defi nition television (SDTV) is basic digital television programming delivered by your service provider. Typically, the SDTV screen is the same, nearly square shape as an analog television screen. Digital images on an SDTV set are crisp and clear—noticeably better than on a standard analog television set using an antenna to receive over-the-air signals.

What Is High-Defi nition Television?

High-defi nition television (HDTV) is a completely new way to send and receive television broadcast signals. HDTV images are made up of pixels that are much smaller and closer together than those used in standard analog television, and there are millions of them. Thus, HDTV can display fi ve to six times the detail of analog television to deliver picture quality that is much more realistic, dimensional, and precise. SDTV programs can be viewed on an HDTV.

Are Local TV Stations or Other Programmers Broadcasting in HDTV?

Many local TV stations and programmers are transmitting digital signals. However, transmitting a digital signal does not mean transmitting an HDTV signal. Some stations are using the new bandwidth to broadcast several standard-defi nition channels. Most stations and programmers, once they begin broadcasting in digital, are offering HD content from their parent network (for example, CBS, ABC,

NBC, Fox, and PBS). Contact your service provider for more information.

Why Aren’t All the Shows I Watch in High-Defi nition?

A high-defi nition program must originate in HD format and be broadcast in HD format. Having an

HDTV system does not mean that everything you watch will be viewed in high-defi nition. Getting the signal from a digital source also does not mean it is high-defi nition.

Why Are Some HDTVs 4:3 Aspect Ratio and Others 16:9?

The aspect ratios differ because television manufacturers build both standard-screen and widescreen HDTVs to appeal to consumer viewing preferences. The two aspect ratios are as follows:

• On standard-screen (4:3) HDTVs, the programming is displayed in letterbox format in the middle of the screen. There are bars surrounding the picture.

• On wide-screen (16:9) HDTVs, the programming is displayed on the full screen.

What Is HDMI and Does it Support Dolby Digital 5.1 Audio?

The High-Defi nition Multimedia Interface (HDMI) is an uncompressed, all-digital audio/video interface.

The Dolby Digital audio format that provides up to 5.1 separate channels of surround sound, and is the standard used for DVD-Video. HDMI supports standard, enhanced, or high-defi nition video, plus multi-channel digital audio, such as Dolby Digital audio, on a single cable.

25

26

Picture Formats

2-23-11 Draft

What Is the Difference Between a Standard-Screen and a Wide-Screen HDTV?

The type of screen your HDTV has (wide-screen or standard-screen) determines how the receiver displays programs on the screen. The picture format for an HDTV is a combination of aspect ratio and screen resolution and is different for standard-screen and wide-screen HDTVs.

What Is Aspect Ratio?

An aspect ratio is the ratio of the width to the height of the TV screen. The aspect ratios differ because the television industry manufactures both standard-screen and wide-screen HDTVs to appeal to consumer viewing preferences.

What Is the Screen Resolution?

The screen resolution indicates the amount of detail that the picture displays. Resolution is identifi ed by the number of display lines on the screen. The techniques that an HDTV uses to “paint” the picture on the screen are referred to as progressive and interlaced.

With the progressive scanning method, the lines are drawn on the screen one at a time in sequential order. Progressive scanning results in a more detailed image on the screen and is also less susceptible to the fl icker commonly associated with interlaced scanning. The interlaced method involves refreshing pixels in alternation — fi rst the odd lines and then the even lines.

For advanced setup, select the screen resolution that your TV can support. Refer to your Feature

Guide and HDTV owner’s manuals to choose the proper screen resolution (480i, 720p, 1080i, or

1080p) for your setup.

For example, a screen resolution of 1080i indicates that the screen shows 1080 lines in an interlaced display, and 720p indicates that the screens shows 720 lines in a progressive display.

A standard-screen HDTV has a 4x3 aspect ratio. The screen is 4 units wide for every 3 units tall.

3

4

A wide-screen HDTV is one-third wider than a standard-screen HDTV. The screen is 16 units wide for every 9 units tall.

16

9

A screen resolution of 480i fi lls the screen.

A screen resolution of 720p, 1080i, or

1080p fi lls the screen.

Index

A

AC Power input 9

Arrow keys 8

Aspect ratio 26

Audio Out 9, 12, 13, 14

B

Back panel 9

Burn-in of screen 24

Buttons See Front Panel

C

Cables 9, 10, 11, 15-23

CAT-5 See Ethernet

Coaxial Cable Input 9, 10, 11, 21

Coaxial network connection 11

Compliance, FCC 29

Component video connection. See YPbPr

Connectors

See also Front panel; Back panel

DVD recorder 14 required for HDTV 12 required for SDTV 13

VCR 14

Connecting the receiver to other devices

DVD recorder 9, 14, 23

HDTV with Component input

(YPbPr) 17

HDTV with DVI connector 12, 16

HDTV with HDMI connector 12, 15

Home Theater System with Component input

(YPbPr) 22

SDTV with Component input (YPbPr) 18

SDTV with an S-Video connector 19

SDTV with an RCA-type connector 20

SDTV with Coaxial cable 21

VCR 9, 14, 23

2-23-11 Draft

Connection

Coaxial Network 11

Consumer electronic devices 10

Controls See Front panel

D

DC Power output 9

Diagrams. See Connecting the receiver to other devices

Digital Video Recorder. See DVR

Digital TV, What is it 25

DVD Connection 9, 14, 23

DVI connector 12, 16

DVR 6

I

E

Ethernet 9, 10, 11 eSATA port 9

F

FAQs 25

FCC compliance 29

Formats, picture 26

Frequently Asked Questions. See FAQs

Front panel 8

H

Hard disk drive, Caution 8

HD format 25

HDTV broadcasting 25

HDTV, what is it 25 indicator 8

HDMI 9, 12, 15

High-defi nition See HD

Home theater system connection 22

Interlaced screen resolution 26

IR sensor 8

27

28

Index,

continued

K

Keys. See Front panel

N

Network 9, 10, 11

O

Optical Audio Output 9, 12, 16, 17, 22

Over-the-air converter box 14

P

Picture formats 26

Ports. See Connectors

Power 8, 9

Programs, view 25

Progressive screen resolution 26

R

Record programs 6

RGB connector 12, 24

S

S-Video Out 9, 13, 14

S-Video In 13, 14

Safety 4, 5

Scan rates. See screen resolution

Screen burn-in 24 resolution 26 size 26

SD

Connections 10, 13, 18, 19, 20, 21

TV, What is it 25

Serial number, locating 7

Sound, performance 24

Standard-defi nition TV 10, 13, 18, 19, 20, 21, 25

Standard-screen TV 26

2-23-11 Draft

T

To Wall (Video In) connector 9, 10, 11

To TV (Video Out) connector 9, 13, 21

Troubleshooting 24

TV digital, what is it 25 formats 26

HDTV, what is it 25 programming 25 recording 6 resolution 26

standard-defi nition 10, 13, 18, 19, 20, 21, 25

U

standard-screen 26 wide-screen 26

USB port 8, 9

V

VCR connection 9, 14, 23

Video In. See To Wall

Video Out. See To TV

View programs 25

W

Wide-screen TV 26

Y

YPbPr connector 9, 12, 13, 17, 18, 22

HDTV connection 12, 17 home theater connection 22

SDTV connection 13, 18

Compliance Information

United States FCC Compliance

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against such interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures:

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the service provider or an experienced radio/television technician for help.

Any changes or modifications not expressly approved by

Cisco Systems, Inc., could void the user’s authority to operate the equipment.

The information shown in the FCC Declaration of Conformity paragraph below is a requirement of the FCC and is intended to supply you with information regarding the FCC approval of this device. The phone numbers listed are for FCC-related questions only

and not intended for questions regarding the connection or operation for this device. Please contact your service provider for any questions you may have regarding the operation or installation of this device.

AVC VIDEO LICENSE

the following notice:

THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO

LICENSE FOR THE PERSONAL USE OF A CONSUMER OR OTHER USES

IN WHICH IT DOES NOT RECEIVE REMUNERATION TO (i) ENCODE VIDEO

IN COMPLIANCE WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR (ii)

DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED

IN A PERSONAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO

PROVIDER LICENSED TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED

OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION

MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE HTTP://WWW.MPEGLA.

COM.

Accordingly, please be advised that service providers, content providers, and broadcasters may be required to obtain a separate use license from MPEG LA prior to any use of AVC/H.264 encoders and/or decoders.

ENERGY STAR

®

Notice

Cisco has tested and confi rmed that the ISB7005 set-top models meet the Tier 1 Energy Effi ciency and Power Management Criteria specifi ed in the ENERGY STAR Program Requirements for Set-top

Boxes Version 2.0.

Macrovision Copyright Notice

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights.

Use of this copyright protection technology must be authorized by

Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

FCC Declaration of Conformity

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: 1) the device may not cause harmful interference, and 2) the device must accept any interference received, including interference that may cause undesired operation.

ISB7005 Receiver

Models ISB7005

Manufactured by: Cisco Systems, Inc.

5030 Sugarloaf Parkway

Lawrenceville, Georgia 30044 USA

Telephone: 770 236-1077

Canada EMI Regulation

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la class B est conforme à la norme

NMB-003 du Canada.

20081121 FCC Standard

Trademarks

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affi liates in the U.S. and other countries. A listing of Cisco’s trademarks can be found at www.cisco.com/go/

trademarks.

AT&T, the AT&T logo, ConnecTech and U-verse are registered trademarks or trademarks of AT&T Knowledge Ventures.

Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

ENERGY STAR and the ENERGY STAR mark are registered trademarks of the U.S. government.

HDMI, the HDMI logo, and High-Defi nition Multimedia Interface are registered trademarks or trademarks of HDMI Licensing LLC in the United States and other countries.

Other third party trademarks mentioned are the property of their respective owners.

The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1009R)

Disclaimer

Cisco Systems, Inc. assumes no responsibility for errors or omissions that may appear in this manual. We reserve the right to change this manual at any time without notice.

29

Federal Communication Commission Interference Statement

2-23-11 Draft

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

•

Reorient or relocate the receiving antenna.

•

•

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

For operation within

5150-5250MHz and 5470-5725MHz frequency range, it is restricted to indoor environment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE:

FCC RF Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The availability of some specifi c channels and/or operational frequency bands are country dependent and are fi rmware programmed at the factory to match the intended destination. The fi rmware setting is not accessible by the end user.

ISB7005 with PCB antenna and max. antenna gain is 5.48 dBi in 5G.

Industry Canada Statement:

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution:

The device for the band

5150-5250MHz and 5470-5725MHz is only for indoor usage to reduce potential for harmful interference to co-channel mobile satellite systems.

The maximum antenna gain permitted (for devices in the bands 5250-5725 MHz (5.48 dBi) to comply with the e.i.r.p. limit; and

The maximum antenna gain permitted (for devices in the band 5725-5825 MHz (5.48 dBi)) to comply with the e.i.r.p. limits specifi ed for point-to-point and non point-to-point operation as appropriate, as stated in section A9.2(3).

High power radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz and 5650-5850

MHz and these radars could cause interference and/or damage to LE-LAN devices.

IMPORTANT NOTE:

Canada RF Exposure Statement:

This system has been evaluated for radiofrequency exposure for humans in reference to Canada Health Code 6

(2009) limits. The evaluation was based on evaluation per RSS-102 Rev 4. The minimum separation distance from the antenna to general bystander is 7.9 inches (20cm) to maintain compliance.

Note: The ISB7005 has disabled the 5600-5650M band by S/W to avoid 5600-5650M band for IC certifi cation.

30

2-23-11 Draft

31

2-23-11 Draft

Cisco Systems, Inc.

5030 Sugarloaf Parkway, Box 465447

Lawrenceville, GA 30042

© 2011 Cisco and/or its affi liates. All rights reserved.

February 2011

678 277-1120

800 722-2009 www.cisco.com

4024566 Rev A