Super Vision at Ultra Low Light SHC-745 User Guide

Super Vision at Ultra Low Light SHC-745 User Guide
Before installing and operating this product,
please read this manual thoroughly.
ENGLISH
Before operating the camera, confirm the camera model and proper input power
voltage. In order to that you can understand this manual thoroughly, we'll introduce our
model description.
nSHC-745 SERIES
• NTSC MODELS SHC-745N • PAL MODELS
SHC-745P
SHC-745PH
n MODEL DESCRIPTION
• SHC-745X
_ X_
The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product's enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
POWER SOURCE
SIGNAL SYSTEM
• SIGNAL SYSTEM
N → NTSC MODEL
P → PAL MODEL
• POWER SOURCE
→ DC12V/AC24V
H → AC 230V~
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
This equipment has been tested and found to comply with limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference
at his own expense.
WARNING - C hanges or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the
equipment.
WARNING - To prevent electric shock and risk of fire hazards:
◆ Do NOT use power sources other than that specified.
◆ Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and
should conform to all local codes.
Contents
Contents
Features
• Features…………………………………………………………………………… 5
• Precautions… …………………………………………………………………… 7
• Components and Accessories……………………………………………… 8
• Overview…………………………………………………………………………… 9
■ Front View……………………………………………………………………………………
■ Side View………………………………………………………………………………………
■ Bottom View……………………………………………………………………………………
■ Rear View………………………………………………………………………………………
9…
9…
10…
11
• Installation Procedures… ……………………………………………………
■ Lens……………………………………………………………………………………………
·When Using Auto Iris Lens………………………………………………………………
·When Using C/CS Mount Lens…………………………………………………………
■ Connecting a Monitor………………………………………………………………………
■ Connecting Power…………………………………………………………………………
■ Control via RS-485 Interface… …………………………………………………………
12
• How to Use the Camera………………………………………………………
■ Function Menu Structure…………………………………………………………………
■ How to Set up the Functions… …………………………………………………………
·LENS…………………………………………………………………………………………
·EXPOSURE…………………………………………………………………………………
·WHITE BALANCE… ………………………………………………………………………
·BACKLIGHT…………………………………………………………………………………
·SSNR…………………………………………………………………………………………
·DAY/NIGHT…………………………………………………………………………………
·IMAGE ADJ…………………………………………………………………………………
·SPECIAL… …………………………………………………………………………………
·EXIT… ………………………………………………………………………………………
18
• Troubleshooting………………………………………………………………
36
• Specifications……………………………………………………………………
37
COLOR CCD CAMERA
4
User Guide
12…
12…
14
15…
16…
17
18…
19…
20…
21…
23…
24…
26…
27…
29…
30…
35
Ultra High Resolution
Motion Detection
By adopting a diagonal 8mm(1/2") 410,000 pixel
ExView Sony CCD, the camera produces clear picture
quality with a horizontal resolution of 560 TV lines for
color, and 700 TV lines for B/W.
Since the camera detects motion and generates
signals without any additional external sensors, you
can monitor activity more efficiently by connecting the
camera to an alarm device.
BLC
DIS (Digital Image Stabilizer)
By adopting a proprietary SV-IV DSP chip, the camera
delivers clear, high quality pictures even in backlight, by
increasing exposure in dark areas while decreasing it in
bright areas; a corrected image with clear details
results.
The DIS function compensates for any camera
movement, to produce more stable pictures.
Video/DC Drive Lens Support
Excellent Sensitivity
By adopting a diagonal 8mm(1/2") highly senstive CCD,
and digital signal processing technology, it can clearly
distinguish the outline and color of a subject in an
extremely low luminance environment – even, for
example, under starlight. Since surveillance is possible
in places where the light is poor, the camera is
appropriate for day and night surveillance outdoors or
on the outside of buildings.
- 0.05 Lux(Color) / 0.00019 Lux(Color Sens-Up Mode)
- 0.006 Lux(B/W)
You can select Video or DC Drive Lens from the menu.
Miscellaneous Functions
HLC(High Light Compensation), SYNC (INT/LL), SENSUP, FLIP (H/V-REV), D-ZOOM, SHARPNESS, MOTION
DETECTION and PRIVACY functions are provided.
SSNR (Samsung Super Noise
Reduction) Function
RS-485 Communication
Control Support
The high performance SV-IV DSP chip dramatically
reduces the gain noise in digital image processing,
producing clear, sharp images in low lighting
environments.
Remote OSD menu control via an RS-485 interface is
supported.
OSD
Day & Night
The camera identifies whether it is day or night and
automatically switches to the appropriate mode,
depending on its environment. By day, the camera
switches to color mode in order to maintain optimal
color. At night, it switches to B/W mode so as to obtain
better picture definition.
COLOR CCD CAMERA
The camera control is convenient by using 9 different
foreign language O.S.D.
- NTSC : Korean, English, Spanish, Japanese, French,
Portuguese
- PAL : English, French, German, Spanish, Italian,
Chinese, Portuguese
5
User Guide
Samsung Techwin cares for the environment at all product manufacturing
stages to preserve the environment, and is taking a number of steps to provide
customers with more environment-friendly products. The Eco mark represents
Samsung Techwin's will to create environment-friendly products, and indicates
that the product satisfies the EU RoHS Directive.
Precautions
Do not install under extreme
temperature conditions.
Do not install in high humidity
environment.
Warnings & Cautions
This information is provided to ensure your safety and to prevent any losses, financial or
otherwise. Please read it carefully and use the product accordingly.
* For product inquiries, please contact the retail shop where you bought the camera. The use of equipment such as
an aerial ladder while providing after-sales service shall be at your expense.
* Separate the power plug when thunder crashes or lighting flashes.
* This product is support equipment for surveillance system. Therefore, we can't compensate for material loss and/or
personal injuries by robbery, fire, natural disaster or something like this type.
Warning/Attention/Special Mark Messages
Ignoring this information may
result in material loss and/or
serious personal injuries including
death.
Ignoring this information may
result in material loss and/or a
slight injuries.
Indicates "Never Allowed."
Indicates "No Disassembling."
Use only under temperature conditions between
-10ºC and +50ºC. Provide good ventilation when
using in high temperature conditions.
May lower image quality.
Do not install under unstable
lighting conditions.
Severe lighting changes or flickering may hinder
normal camera operation.
Avoid touching the camera lens.
The lens is the most important component of
the camera. Be careful not to smear it with
fingerprints.
Do not drop the camera or subject
it to physical shock.
May cause a product malfunction.
COLOR CCD CAMERA
6
User Guide
Never keep the camera face to
strong light directly.
May damage the CCD.
COLOR CCD CAMERA
7
User Guide
Precautions
Overview
Do not expose the camera to rain
or other types of liquids.
Front View
Do not expose the camera to
radioactivity.
❶
2
May cause a product malfunction.Wipe dry any
liquids. Liquids may contain minerals that are
corrosive to electronic components.
Notes
• Exposure to a spotlight or an object emitting strong light may cause smear or blooming.
• Ensure that the power source complies with normal specifications before supplying it to
the camera.
Components and Accessories
1
3
Radioactivity exposure may damage the CCD.
2
3
1 Tripod Mounting Bracket Screw Hole
Used to fix the Tripod Mounting Bracket to the top of the camera.
2C
-Mount Lens Adapter
Install this adapter to use a C-Mount Lens.
3 Back Focus Control Lever
Adjust focus by this Back Focus Lever.
Side View
4
4
1 Ultra Low Light Color CCD Camera SHC-745
3 Auto Iris Lens Connector Plug
COLOR CCD CAMERA
8
2 Instruction Manual
4 C-Mount Adapter
User Guide
4 Auto Iris Lens Connector
Used to connect Auto Iris Lens plug.
COLOR CCD CAMERA
9
User Guide
Overview
Overview
Rear View
Bottom View
❿
6
⓫
5
7
⓬
8
9
*High Voltage Type
5 Tripod Mounting Bracket Screw Hole
Used to fix the camera on a bracket or tripod.
The screw sizes for this hole are as follows:
1/4"-20 UNC (20 THREAD)
L:4.5mm±0.2mm (ISO standard),
or 0.197" (ASA standard)
You can separate the Tripod Mounting Bracket and install it on the
top or bottom of the camera. Make sure to use the Tripod
Mounting Bracket when fixing the camera to a bracket or tripod.
Otherwise the camera may not be secure, or the internal circuitry of
the camera may be damaged.
COLOR CCD CAMERA
10 User Guide
(SHC-745PH)
6 Function Setup Button
• SET Button : Displays
the menu on the screen. Press this button to confirm status or
after changing a selected item.
• Up and Down Button : Used to move the cursor up or down in the menu screen to
select a desired menu item.
• Left and Right Button : U
sed to move the cursor left or right in the menu screen or to
change the value of the selected item.
7 D & N Input Port
You can switch to Day & Night Mode by connecting an external signal to this port.
8 MD Output Port
Motion detection signals are output through this port.
9 RS-485 Control Port
You can control SETUP MENU through this port by using external controllers like a Remote
controller that RS-485 Communication is supported. For details, see page 21.
❿ Video OUT Port
Video signals are output through this port. Connect this port to the Video IN port of a
monitor.
⓫ Power LED
When power is properly connected, this LED comes on.
⓬ Power IN Port
Connect the power as specified for each model here.
COLOR CCD CAMERA
11 User Guide
Installation Procedures
Lens
The lens is not supplied with this camera. Purchase a lens suitable for your
environment. This camera accepts the auto iris lens and both C-and CS-mount
lens.
Notes
Installation Procedures
3. R
emove the cover of the auto iris lens connector plug and solder the lens cable to
the connector pin of the plug.
• For a Video Drive Lens
• For a DC Drive Lens
Pin 1: Red (Power)
Pin 1: Damping Pin 2: NC
Pin 2: Damping +
Pin 3: White (Video Signal)
Pin 3: Drive +
Pin 4: Black (Ground)
Pin 4: Drive -
• It is recommended to use the DC type Auto Iris Lens to effectively enjoy the major
functions of this camera.
• Keep the lens surface clean, since if it is contaminated with dirt or fingerprints the
picture quality suffers.
Lens cable
No. 3 Pin
No. 1 Pin
When Using Auto Iris Lens
1. Strip the insulation of the auto iris lens cable 8mm from the end.
approx. 8mm
connector
No. 4 Pin
No. 2 Pin
4. F it the cover of the auto iris lens connector
plug, remove the protective glass cover
from the front of the camera, and fasten
the auto iris lens by turning it clockwise.
2. Strip the insulation of the core of the auto iris lens cable to expose a 2mm length.
approx. 2mm
5. S et focus of camera using Back Focus Control
Lever of camera side after combining Auto
Iris lens.
Back Focus Control Lever
COLOR CCD CAMERA
12 User Guide
COLOR CCD CAMERA
13 User Guide
Installation Procedures
When Using C/CS Mount Lens
Before installing a lens, identify whether the lens to be installed is a C-Mount or CS-Mount.
This camera is set for a CS-Mount Lens by default. To install a C-Mount Lens, a
simple modification is required.
• When Using a CS Mount Lens
Remove the protective glass cover at the
front of this product and turn the CS-Mount
Lens clockwise to install it. And set focus of
camera using Back Focus Control Lever of
camera side after combining CS-Mount lens.
Installation Procedures
2. Turn the C-Mount lens clockwise to install
it.
3. S et focus of camera using Back Focus
Control Lever of camera side after
combining C-Mount lens.
Connecting to Monitor
Connect the Video OUT port on the rear panel of the camera to a monitor.
CCD Camera
Monitor
Notes
• Use the lens connector shown in the following figure. If the dimensions of the connector
are not correct, it may damage the camera, or the lens may not be installed firmly.
• If the lens is too heavy, the camera becomes unbalanced and
there may be problems. Use a lens that weighs less than
450g.
• When adjusting the Automatic Level Control (ALC) of an auto
iris lens, use Av mode if available. If you use the Pk mode, the
picture brightness may change continuously.
C-Mount Lens: 10mm or less
CS-Mount Lens: 5mm or less
• S ince the connection procedure may differ depending on the type of monitor or
peripheral device to be connected, refer to the User Manual for the device to be
connected.
• Make sure to turn off the device to be connected before making any connections.
• Turn the 75Ω/Hi-Z switches of interim display devices to the Hi-Z position, and the
switches of any final device to the 75Ω position.
Intermediate
• When Using a C Mount Lens
1. Remove the protective glass cover at the
front of this product and turn the C-Mount
Adapter clockwise to install it.
CCD Camera
COLOR CCD CAMERA
14 User Guide
COLOR CCD CAMERA
15 User Guide
End monitor
Installation Procedures
Installation Procedures
Connecting to Power
Control via RS-485 Interface
Since power specifications differ depending on the model, make sure to check your
model name and specifications before connecting power.
You can connect power as shown in the following figure.
For AC / DC power
• Since the power specification supports
both AC and DC, connect AC 24V,
500mA Adaptor or DC 12V, 500mA
Adaptor.
The camera can be controlled by using external controllers like a Remote controller.
(RS-485 Communication)
(1) To control by PC
Connect the RS-485 control port of the camera and the serial cable through an
RS-485 converter.
Example) P C Serial Port (COM1) → Serial Cable → RS-485 Converter → Camera
RS-485 Control Port
485 Control Board Connection Port
(+) CONNECTION TERMINAL (TRX+)
( - ) CONNECTION TERMINAL (TRX-)
RS-485 Control Port
485+
485-
* RS-485 Communication establishment initial value
Item
Initial value
High Voltage Type (AC230V, 50Hz)
• Use AC230V, 50Hz power source For
SHC-745PH.
Camera ID
1
BAUD RATE
9600
UART MODE
8-NONE-1
PET PKT
ENABLE
Notes
• To control the camera by constructing an additional controller, use Pelco-D protocol or
STW protocol (Samsung Techwin protocol).
When the resistance value of copper wire is at [20°C(68°F)]
#24(0.22mm2)
#22(0.33mm2)
#20(0.52mm2)
#18(0.83mm2)
Resistance (Ω/m)
0.078
0.050
0.030
0.018
Voltage Drop (V/m)
0.028
0.018
0.011
0.006
Copper wire size (AWG)
• As shown in the table above, voltage decreases as the wire gets longer.
Therefore use of an excessively long adaptor output line for connection to the
camera may affect the performance of the camera.
Standard voltage for camera operation : DC 12V±10%, AC 24V±10%
There may be some deviation in voltage drop depending on the type of wire and the manufacturer.
COLOR CCD CAMERA
16 User Guide
COLOR CCD CAMERA
17 User Guide
How to Use the Camera
How to Use the Camera
Function Menu Structure
How to Set up the Functions
You can set up functions using the 5 buttons on the rear of the camera.
Setup Menu
LENS SHADE
●DC
●VIDEO
●MANUAL
UP button
SET button
EXPOSURE
●SHUTTER
●RETURN
●AGC
●SENS-UP
LEFT button
WHITE BALANCE
●ATW
●OUTDOOR
●MANUAL
●INDOOR
●AWC→SET
BACKLIGHT
●OFF
●BLC
●HLC
SSNR
●ON
●OFF
DAY/NIGHT
●COLOR
●EXTERN
●B/W
●AUTO
IMAGE ADJUSTMENT
(IMAGE ADJ.)
●V-REV
●SHARPNESS
●H-REV
●RETURN
●D-ZOOM
SPECIAL
●CAMTITLE
●PRIVACY
●LANGUAGE
●SYNC
●DIS
●RESET
●MOTION DET
●COMM ADJ
●RETURN
DOWN button
RIGHT button
1. Press the SET button.
• Main setup menu is displayed on the monitor screen.
Select the function using
the UP or DOWN button.
MAIN SETUP
1.LENS DC 2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
6.DAY/NIGHT AUTO
7.IMAGE ADJ
8.SPECIAL
9.EXIT
Change the status
using the LEFT or
RIGHT button.
2. Select a desired function using the Up and Down buttons.
• Place the cursor over a desired item.
3. Set up a selected item by using the Left and Right buttons.
4. To finish the setting, select ‘EXIT’ and press the SET button.
Notes
EXIT
• An item with the icon also has sub menus. To select a sub menu, select an item with the icon
and press the Function Setup switch.
• An item with the - - - icon is unavailable due to function settings.
COLOR CCD CAMERA
18 User Guide
COLOR CCD CAMERA
19 User Guide
How to Use the Camera
How to Use the Camera
EXPOSURE
LENS
Using this function, you can control screen brightness.
1. When the SETUP menu screen is displayed, select‘LENS’by using the Up and
Down buttons so that the arrow indicates‘LENS’.
2. Select the connected lens type by using the Left and Right buttons.
MAIN SETUP
1.LENS DC 2.EXPOSURE
DC/Video : Select Auto Iris Lens
• When DC is selected, you can control screen
brightness. The range of brightness control is
between 1 and 70. Adjust the brightness
appropriately for optimal screen brightness.
Notes
• When you use DC lens, set the shutter mode to fixed(---) if Color Rolling is occurred.
• Some lenses may not work properly, depending on the setting of the BRIGHTNESS LEVEL.
• When Using a Video-Type Auto Iris Lens
1 Adjust the ALC adjustment terminal on the lens appropriately. In general, set it to AV
(Average).
2 It may not work properly depending on the installed lens. Set the Level VR of the lens
to the optimal value.
3 Set AGC to OFF and adjust the Lens VR to an appropriate brightness.
4 Adjust the Lens VR, adjust the BRIGHTNESS, and then check if the screen brightness changes
properly. Otherwise, adjust the Lens VR again.
Manual : Select Manual Lens
COLOR CCD CAMERA
20 User Guide
MAIN SETUP
1.LENS DC 2.EXPOSURE
3.WHITE BAL ATW
1. When the SETUP menu screen is displayed, select
‘EXPOSURE’by using the Up and Down buttons
so that the arrow indicates‘EXPOSURE’.
2. Select a desired mode using the Up and Down
buttons.
SHUTTER : You can select either auto or manual shutter.
- A.FLK : Select this when you experience picture flicker, which can happen when
there is a clash with the frequency of the installed lighting.
- ESC : S elect this to control the shutter speed automatically. If ESC is selected,
the shutter speed is automatically controlled depending on the ambient
illumination of the subject.
- MANUAL : You can control shutter speed manually.
Notes
• When you use DC lens, set the shutter mode to fixed(---) if Color Rolling is occurred.
• When the SHUTTER is set to ESC after selecting the Internal Synchronization Type, the
picture may become unstable if the camera faces a bright fluorescent light. Therefore,
take care when choosing the installation position.
• When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP will be disabled.
COLOR CCD CAMERA
21 User Guide
How to Use the Camera
AGC (AUTO GAIN CONTROL) :
The higher the gain level, the brighter the screen - but the higher the noise.
- OFF : Deactivates the AGC function.
- LOW : Allows automatic gain control from 0 to 30dB.
- HIGH : Allows automatic gain control from 0 to 42dB.
SENS-UP : When it is night or dark, the camera
automatically detects the light level
and maintains a clear picture if this
mode is activated.
- OFF : Deactivates the SENS-UP function.
- AUTO : Activates the SENS-UP function.
RETURN :
Select this to save the changes in the EXPOSURE menu and return to the
SETUP menu.
How to Use the Camera
White Balance (White Bal.)
Use the White Balance function to adjust the screen color.
1. When the SETUP menu screen is displayed, select‘White Bal.’by using the Up
and Down buttons so that the arrow indicates‘White Bal.’.
2. Select a desired mode using the Up and Down buttons.
※ Select one of the following 5 modes, as appropriate for your purpose.
ATW : Select this when the color temperature is between 1800°K and
Notes
• If you press the SET button in ‘AUTO’ mode, You can adjust brightness by increasing or
decreasing the shutter speed. (x2 ~ x256)
• Note that the higher the zoom level, the brighter the screen, but the more likely it is that
an after-image will appear.
• Although Noise, Spots, and Whitish symptoms may occur in SENS-UP operation when the
zoom level is increased, this is normal.
COLOR CCD CAMERA
22 User Guide
MAIN SETUP
1.LENS DC 2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
10500°K.
INDOOR : Select this when the color temperature is between 4500°K and
8500°K.
OUTDOOR : Select this when the color temperature is between 1800°K and
10500°K. (sodium light inclusion)
AWC→SET : To find the optimal setting for the current luminance
environment in this mode, set the point the camera towards a
sheet of white paper and press the SET button. If the
environment changes, readjust it.
MANUAL : Select this to fine-tune White Balance manually. Set White Balance
first by using the ATW or AWC mode. After that switch to MANUAL
mode, fine-tune the White Balance and then press the SET button.
COLOR CCD CAMERA
23 User Guide
How to Use the Camera
Notes
• White Balance may not work properly under the following conditions. In this case select
the AWC mode.
1 When the color temperature of environment surrounding the subject is out of the
control range (e.g. clear sky, or sunset)
2 When the ambient illumination of the subject is dim.
3 If the camera is directed towards a fluorescent light or is installed in a place where illumination
changes dramatically, the White Balance operation may become unstable.
BACKLIGHT
This camera is designed so that it delivers a distinctive subject and background at
the same time, even when the subject is in backlight, unlike conventional cameras,
by adopting a proprietary SV-IV DSP chip.
1. When the SETUP menu screen is displayed, select‘BACKLIGHT’by using the
Up and Down buttons so that the arrow indicates‘BACKLIGHT’.
MAIN SETUP
1.LENS DC 2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
2. S elect a desired mode using the Left and Right buttons depending on the camera purpose.
BLC : Enables a user to directly select a desired area from a picture, and to
view the area more clearly.
BLC ON
COLOR CCD CAMERA
How to Use the Camera
HLC (High Light Compensation) :
If the scene contains extremely bright light areas such as; from car headlight,
the light can mask out much of the on-screen detail.
- DAY : In normal daylight conditions, the HLC is not activated.
- NIGHT : If a high light that is larger than a certain size is present on the
screen, HLC is activated to remove the high light.
OFF : Not being used
3. S elect a desired mode using the Left and Right
buttons and press the SET button.
Select ‘BLC’ to adjust the area to be enhanced
and enhancement level.
HLC : Enable a user to select a mask color of
high light area from a picture.
Notes
• Because there can be a difference in the effectiveness of HLC according to the amount of
light area in the screen, optimize the installation angle for the best HLC performance.
• In a dark environment, the HLC is only activated when a high light that is larger than a
certain area is present.
• The HLC is not activated in light or overly dark conditions.
BLC OFF
24 User Guide
COLOR CCD CAMERA
25 User Guide
How to Use the Camera
How to Use the Camera
SSNR
DAY/NIGHT
This function reduces the background noise in a low luminance environment.
1. When the SETUP menu screen is displayed, select‘SSNR’by using the Up and
Down buttons so that the arrow indicates‘SSNR’.
You can display pictures in color or black and white.
1. When the SETUP menu screen is displayed, select‘DAY/NIGHT’by using the Up
and Down buttons so that the arrow indicates‘DAY/NIGHT’.
MAIN SETUP
1.LENS DC 2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
6.DAY/NIGHT AUTO
2. Select a desired mode using the Left and Right buttons.
OFF : Deactivates SSNR. Noise is not reduced.
ON : Activates SSNR so that noise is reduced.
3. Set the SSNR mode to‘ON’and press the SET
button. Then you can adjust the noise reduction
level.
2. S elect a desired mode using the Left and Right buttons according to the picture
display you want.
COLOR : The picture is always displayed in color.
B/W : The picture is always displayed in black and white.
AUTO : The mode is switched to Color in a
normal environment, but switches to
B/W mode when ambient illumination
is low. To set up the sswitching time or
speed for AUTO mode, press the SET
button.
Notes
• You cannot set the SSNR to ‘ON’ or ‘OFF’ when the AGC mode of the EXPOSURE menu is
‘OFF’.
• When adjusting the noise reduction level of the SSNR mode, remember that the higher the
level set, the more the noise level will be reduced but that after image may also occur.
COLOR CCD CAMERA
26 User Guide
MAIN SETUP
1.LENS DC 2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
6.DAY/NIGHT AUTO
7.IMAGE ADJ
- DWELL TIME : You can select the duration time about changing the day/night
mode. →5s, 7s, 10s, 15s, 20s, 30s, 40, 60s
- DURATION : You can select brightness of illumination about changing the day/
night mode.
COLOR CCD CAMERA
27 User Guide
How to Use the Camera
Fast
Slow
Color → B/W
2.5 lux
0.8 lux
B/W → Color
4 lux
6 lux
* The brightness of illumination is changeable by
installed environment.
How to Use the Camera
IMAGE ADJ.
1. When the SETUP menu screen is displayed, select‘IMAGE ADJ.’by using the
Up and Down buttons so that the arrow indicates ‘IMAGE ADJ.’.
EXTERN : This mode allows you to apply a desired filter to external signals.
Notes
• When using a Video Auto Iris Lens, if you set the lens level to low, automatic switching
between Color and Black & White may not occur.
• You cannot control the DAY/NIGHT menu when AGC in the EXPOSURE menu is‘OFF’.
At this time, the exchange between DAY mode and NIGHT mode operates as like selecting
‘COLOR’mode.
• The OSD key does not work for 3 seconds when switching to Color or B/W, to ensure
stable camera operation.
• The camera may focus less well under infrared illumination than under normal illumination.
• Since the camera may not focus as well under infrared illumination at night as it does
under normal illumination, install an Extra-low Dispersion Lens to obtain sharp pictures.
2. Select a desired mode using the Up and Down buttons.
COLOR CCD CAMERA
28 User Guide
MAIN SETUP
1.LENS DC 2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
6.DAY/NIGHT AUTO
7.IMAGE ADJ
8.SPECIAL
1.
2.
3.
4.
5.
6.
7.
IMAGE SETUP
V-REV
H-REV
D-ZOOM
SHARPNESS
PED LEVEL
COLOR
RETURN
OFF
OFF
OFF
ON
0
170
V-REV : You can flip the picture vertically on the screen.
H-REV : You can flip the picture horizontally on the screen.
D-ZOOM : You can use a digital zoom of x2~x10.
COLOR CCD CAMERA
29 User Guide
How to Use the Camera
SHARPNESS : As you increase this value, the
picture outline becomes stronger
and clearer. Adjust this value
appropriately depending on the
sharpness of the picture.
How to Use the Camera
2. Select a desired mode using the Up and Down buttons.
0
PED LEVEL, COLOR : Please use this menu item when using a LCD monitor
other than standard ones. You can change PED LEVEL,
and COLOR menu.
RETURN : Select this to save the settings for the IMAGE ADJ. menu and to
return to the SETUP menu.
SPECIAL
1.CAM TITLE OFF
2.SYNC INT
3.MOTION DET OFF
4.PRIVACY OFF
5.DIS OFF
6.COMM ADJ
7.LANGUAGE ENGLISH
8.RESET 9.RETURN Notes
• When the V-REV or H-REV mode is enabled, the text on the screen does not flip.
• If you increase the SHARPNESS level too high, the picture may become distorted or noise may
appear.
CAM TITLE : If you enter a title, the title will appear on the monitor.
❶ If the SPECIAL menu screen is displayed, use the Up and Down buttons so
that the arrow indicates ‘CAM TITLE’.
2 Set it to ‘ON’ by using the Left and Right buttons.
SPECIAL
1. When the SETUP menu screen is displayed, select‘SPECIAL’by using the Up
and Down buttons so that the arrow indicates‘SPECIAL’.
MAIN SETUP
1.LENS DC 2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
6.DAY/NIGHT AUTO
7.IMAGE ADJ
8.SPECIAL
9.EXIT
COLOR CCD CAMERA
30 User Guide
Notes
• W
TITLE
menu
is‘OFF’,
no title
･ When
henthe
theCAM
CAM
TITLE
menu
is ﾔOFFﾕ,
no
will
on theon
monitor
screenscreen
even if
titlebe
willdisplayed
be displayed
the monitor
you
one.
evenenter
if you
enter one.
• Only English is available in the mode.
COLOR CCD CAMERA
SPECIAL
1.CAM TITLE
2.SYNC
3.MOTION DET
4.PRIVACY
5.DIS
6.COMM ADJ
7.LANGUAGE
8.RESET 9.RETURN 31 User Guide
OFF
INT
OFF
OFF
OFF
ENGLISH
How to Use the Camera
3 Press the SET button.
4 Use the 4 direction buttons to move
to a desired letter and select the letter
by pressing the SET button. Repeat
this to enter multiple letters. You can
enter up to 15 letters.
CAMERA TITLE SETUP
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
abcdefghijklm
nopqrstuvwxyz
-.0123456789
←→CLR POS END
Notes
• If you move the cursor to CLR and press the SET button, all the letters are deleted. To edit
a letter, change the cursor to the bottom left arrow and press the SET button. Move the
cursor over the letter to be edited, move the cursor to the letter to be inserted and then
press the SET button.
5 Enter a title, move the cursor to ’POS’ and
FRONT DOOR
press the SET button. The entered title
appears on the screen. Select the position to
display the title on the screen by using the 4
direction buttons and press the SET button.
When the position is determined, select
’END’ and press the SET button to return to
the SPECIAL menu.
SYNC : In areas where the supply is at 60Hz,
you can synchronize the output phase
of multiple cameras using the power
synchronization function (Line-Lock)
without using a synchronization signal
generator.
- INT : Internal Synchronization Type
- L/L : Power Synchronization Type, Line-lock
• Press the SET button.
• You can select a desired phase from 0 to 359 when select 'phase'.
• You can decide the synchronization between luminance and color signal
when select the 'Mode' to TRACE.
COLOR CCD CAMERA
32 User Guide
How to Use the Camera
Notes
• When using AC power at 60Hz frequency, you can use the L/L type synchronization.
• When the power is DC 12V, the SYNC. menu is fixed to the ‘INT’ mode.
MOTION DET : If you connect an alarm device to this camera,
you can monitor activity more efficiently,
because a signal is generated by the camera
whenever motion is detected. The motion
detection signal is output through the MD OUT
port.
❶ When the SPECIAL menu screen is displayed, press the Up and Down
buttons so that the arrow indicates MOTION DET .
2 Set up the mode using the 4 direction buttons.
- SENSITIVITY : You can select up to 8 MD areas. When SENSITIVITY number
is high, motion detection sensitivity is increased to recognize
even small movement.
- AREA MODE : D etermines whether to use the MD area selected in
SENSITIVITY.
- SEL POS : Determines which of the 4 vertices of each MD area is to be
used.
- YPOS : Determines the coordinate of the vertical axis for SEL POS.
- XPOS : Determines the coordinate of the horizontal axis for SEL POS.
- FILL→SET : Fills in a selected MD area. Fills in a selected MD area. The
color of filling is sequentially selected as brown, orange, blue,
cyan, yellowish green, yellow and red.
- RETURN : S elect this to save the MOTION DET menu settings and return to
the SPECIAL menu.
Notes
• MD areas show only MOTION DET menu. Therefore, MD areas don’t display on the
monitor screen.
COLOR CCD CAMERA
33 User Guide
How to Use the Camera
PRIVACY : Hide an area you want to hide on
the screen.
❶ When the SPECIAL menu screen is displayed,
press the Up and Down buttons so that the
arrow indicates ‘PRIVACY’.
2 S et up the mode using the 4 direction
buttons.
- AREA SEL : You can select up to 8 PRIVACY
areas.
- AREA MODE :
Determines whether to use the area
selected in the AREA SEL, and the size and
position of the area.
- MASK COLOR : Determine area color. You can select Gray, Green, Red,
Blue, Black, White.
- TRANSP : Determine the transparency of selected area as controlling
number from 0 to 3.
- RETURN : Select this to save the PRIVACY menu settings and return to the
SPECIAL menu.
DIS (Digital Image Stabilizer) : This function mitigates any picture movement due to external factors such as
wind.
How to Use the Camera
COMM ADJ (Communication Adjustment) : This function sets up the camera communication
status when controlling the camera through an
external control device.
❶ When the SPECIAL menu screen is displayed, press the Up and Down
buttons so that the arrow indicates ‘COMM ADJ’.
2 Set up the mode using the 4 direction buttons.
- CAM ID : D
etermines the camera's identification number (between 0 and
255).
- BAUD RATE : You can select 2400/4800/9600/19200/38400/57600 bps.
- UART MODE : You can select NONE, EVEN or ODD for the parity bits.
- RET PKT : D
etermines whether to send a command back to the controller
device when a communication control command is sent to the
camera.
- DISP CAM ID : Display camera title on top left corner of the screen.
LANGUAGE : You
can select the menu language according to your
requirements.
RESET : Resets
the camera settings to the factory defaults. Communication
status and language is not initialized.
RETURN : Select
this to save the SPECIAL menu settings and return to the
MAIN SETUP menu.
EXIT
Notes
• The chance of resolution decrease is existed because DIS function uses the digital zoom.
• DIS doesn’t operate when background illumination is too low.
• DIS doesn’t operate when object pattern is monotonic as like sky or white wall.
• If DIS is enabled, the digital zoom is not configured to less than 46 level.
COLOR CCD CAMERA
34 User Guide
Press the SET button in the EXIT menu to save the current settings and exit the MAIN SETUP
menu .
COLOR CCD CAMERA
35 User Guide
Troubleshooting
Specifications
If you have trouble operating your camera, refer to the following table.
If the guidelines do not enable you to solve the problem, contact an authorized
technician.
● Nothing appears on the screen.
▶ Check that the power cord and line connection between the camera and monitor are fixed properly.
▶ Check that you have properly connected VIDEO cable to the camera VIDEO output jack.
▶ Check that the lens type is VIDEO lens or DC lens.
● The image on the screen is dim.
▶ Is lens stained with dirt? Clean your lens with soft, clean cloth.
▶ Set the monitor to proper condition.
▶ If the camera is exposed to too strong light, change the camera position.
● The image on the screen is dark.
▶ Adjust the contrast feature of the monitor.
▶ If you have an intermediate device, set the 75Ω / Hi-z properly.
● The camera is not working properly, and the surface of the camera is hot.
▶ Check that you have properly connected the camera to an appropriate power source.
● The DAY/NIGHT menu does not work.
On Screen Display
▶ Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
● The SENS-UP function does not work.
▶ Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
▶ Check that SHUTTER of EXPOSURE SETUP menu is ‘A.FLK’ or ‘MANUAL’.
● The Motion Detection function does not work.
▶ Check that MOTION DEF of SPECIAL SETUP menu is ‘OFF’.
● Color is not correct.
▶ Check the setting of WHITE BAL SETUP menu .
● The screen flickers continually.
▶ Check that direction of camera turns toward the Sun.
● RS-485 communication fails.
▶ Check the polarity between RS-485 Control Port and RS-485 cable.
485 Control Board Connection Port
(+) CONNECTION TERMINAL (TRX+)
( - ) CONNECTION TERMINAL (TRX-)
RS-485 Control Port
485+
485-
▶ Check the RS-485 Communication establishment initial value
* RS-485 Communication establishment initial value
Item
Camera ID BAUD RATE UART MODE
Initial value
1
9600
8-NONE-1
RET PKT
ENABLE
▶ We recommend that you make ground connect between camera and controller in order to maintain
safety communication control.
COLOR CCD CAMERA
SHC-745N
ELECTRICAL
Input Voltage
Power Consumption
VIDEO
Imaging Device
Total Pixels
Effective Pixels
Scanning System
Synchronization
Frequency
Horizontal Resolution
Min. Illumination
S/N (Y Signal)
Video Output
OPERATIONAL
IRIS Adustment
Electronic Shutter Speed
36 User Guide
Backlight Compensation
Day & Night
Gain Control
White Balance
SENS-UP (frame Integration)
Motion Detection
Privacy Masking
3D Noise Filter (SSNRII)
Digital Zoom
Digital Image Stabilization(DIS)
Camera Title
Sharpness
Flip / Mirror
Communication
Protocol
ENVIRONMENTAL
Operating Temperature / Humidity
MECHANICAL
Lens Mount
Back Focus Adjustment
Dimension
Weight
SHC-745P
AC 24V / DC 12V
4.0W
SHC-745PH
AC 230V
Diagonal 8mm (1/2") Sony Exview HAD CCD
811(H) x 508(V)
795(H)x596(V)
768(H) x 494(V)
752(H)x582(V)
2:1 Interlace
Internal / Line Lock
H : 15.734KHz / V : 59.94Hz H: 15.625KHz / V: 50.00Hz
COLOR : 560TV lines (Min.) / B&W : 700TV lines (Min.)
0.05 Lux (Color), 0.00019 Lux (Color Sens-Up Mode), 0.006 Lux (B/W)
52dB (AGC Off, Weight On)
CVBS : 1.0Vp-p / 75Ω
DC / VIDEO
ESC (1/60(PAL : 1/50) ~ 1/120,000 sec) / MANUAL / A.FLK
NTSC : Korean, English, Spanish, Japanese, French, Portuguese
PAL : English, French, German, Spanish, Italian, Chinese, Portuguese
BLC / HLC / OFF
COLOR / B&W / AUTO (ICR)
LOW / HIGH / OFF
ATW / AWC / MANUAL / INDOOR / OUTDOOR (1,800°K ~ 10,500°K)
AUTO / OFF (x2 ~ x256)
ON / OFF (8 programmable zones)
OF / OFF (8 programmable zones)
ON / OFF (Level adjustable)
ON / OFF (x2 ~ x10)
ON / OFF
ON / OFF
ON / OFF
ON / OFF
RS - 485 (Baudrate 2400, 4800, 9600, 19200, 38400, 57600bps selectable)
Samsung Techwin Protocol, Pelco-D Protocol
-10°C ~ +50°C / 30% ~ 80% RH
C / CS Mount (Easy Focus type)
Manual
65.8(W)x60.6(H)x101.9(D)mm
315g
COLOR CCD CAMERA
65.8(W)x60.6(H)x115(D)mm
535g
37 User Guide
DECLARATION OF CONFORMITY
Application of Council Directive(s)
89 / 336 / EEC
Manufacturer's Name SAMSUNG TECHWIN CO., LTD
Manufacturer's Address
SAMSUNG TECHWIN CO., LTD
42, SUNGJU-DONG CHANGWON-CITY,
KYUNGNAM, KOREA, 641-716
MEMO
European Representative Name
European Representative Address
Equipment Type/Environment CCTV Camera
Model Name SHC-745P/PH
Beginning Serial NO. S8110001
Year of Manufacture 2008. 11. 01
Conformance to EN 50081-1 : 1992
EMC-Directive 89/336 EEC and 92/31/EEC
EN 50130-4 : 1996
We, the undersigned, hereby declare that the equipment specified above conforms
to the above Directive(s).
Manufacturer SAMSUNG TECHWIN CO., LTD Legal Representative in Europe
Signature Signature
Full Name BONJENG GU
Full Name Position QUALITY CONTROL MANAGER Position Place CHANGWON, KOREA
Place
Date 2008. 11. 01
Date
COLOR CCD CAMERA
38 User Guide
COLOR CCD CAMERA
39 User Guide
SALES NETWORK
•
AMSUNG TECHWIN CO., LTD.
S
145-3, Sangdaewon 1-dong, Jungwon-gu, Seongnam-si Gyeonggi-do, Korea, 462-703
TEL : +82-31-740-8151~8 FAX : +82-31-740-8145
•
AMSUNG TECHWIN AMERICA Inc.
S
1480 Charles Willard St, Carson, CA 90746, UNITED STATES
Tol Free : +1-877-213-1222 FAX : +1-310-632-2195
www.samsungcctvusa.com
•
AMSUNG TECHWIN EUROPE CO., LTD.
S
Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300 FAX : +44-1932-45-5325
www.samsungtechwin.com
www.samsungcctv.com
P/No. : Z6806-0854-01C
VAN 09. 10