DTS XR2000 SPOT CMY User manual

XR2000 SPOT

03.MS009.EB.L

User’s Manual Rel 1.3

GB

D.T.S. Illuminazione srl - ITALY http://www.dts-lighting.it

Made in Italy

2

XR2000 SPOT

Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso scritto della D.T.S .

DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di design a ciascun proprio prodotto. D.T.S non assume alcuna responsabilità sull’uso o sull’applicazione dei prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and checked. However, no responsibility will be taken for any errors. All rights are reserved and this document cannot be copied, photocopied or reproduced, in part or completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement, sans le consentement préalable de D.T.S

.

D.T.S.

se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou de design, sans préavis, à chacun de ses produits. D.T.S.

décline toute responsabilité sur l'utilisation ou sur l'application des produits ou des circuits décrits.

Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.

Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado o reproducido, total o parcialmente, sin previa autorizaciónescrita de D.T.S.

D.T.S.

se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter estético, funcional o de diseño a cada producto suyo. D.T.S.

no se asume responsabilidad de ningún tipo sobre la utilización o sobre la aplicació n de los productos o de los circuitos descritos.

3

INDEX:

1- SYMBOLS

2- GENERAL WARNING

3- GENERAL WARRANTY CONDITION

4- TECHNICAL FEATURES

5- ACCESSORIES

6- IMPORTANT SAFETY INFORMATION

6.1 Fire prevention

4

4

4

5

7

8

6.2 Prevention of electric shock

6.3 Protection against ultraviolet radiation

6.4 Safety

6.5 Level of protection against the penetration of solid and liquid objects

7- MOUNTING THE LAMP

7.1 Lamp alignment

9

8- VOLTAGE AND FREQUENCY

9- INSTALLATION

9.1 Safety cable

9.2 Protection against liquids

9.3 Movement

10

10

9.4 Risk of fire

9.5 Forced ventilation

9.6 Ambient temperature

10- MAINS CONNECTION

10.1 Protection

11- DMX SIGNAL CONNECTION

11

12

11.1 DMX Addresses

11.2 Selecting the DMX address

12- FIRMWARE UPDATING

13- DISPLAY FUNCTIONS

13

14

14- ERROR MESSAGES 17

15- HIDDEN MENU 18

15.1 Calibration mode 19

16- PAN & TILT SPEED 20

17- FANS SPEED

18- OPENING THE PROJECTOR HOUSING 21

19- REPLACING GOBOS

20- PERIODIC CLEANING

20.1 Lenses and reflectors

22

20.2 Fans and air passages

21- PERIODIC CONTROLS

22- DMX PROTOCOL

23- 8 MOTORS CONTROL CARD

24- 8 MOTORS SLAVE CONTROL CARD

23

38

39

25- PAN & TILT CARD 40

26- CABLES RESEND CARD

27- DISPLAY CARD

28- LAMP ON-OFF CONTROL CARD

29- ROTATING GOBO WHEEL 41

30- FIXED GOBO WHEEL 42

31- COLOUR WHEEL 1 43

32- COLOUR WHEEL 2 44

XR2000 SPOT

4

1- SYMBOLS

Graphic symbols used on this manual

THIS SYMBOL INDICATES A HOT SURFACE

XR2000 SPOT

THIS SYMBOL INDICATES ELECTRIC SHOCK RISK

!

THIS SYMBOL INDICATES GENERAL RISK

F

THIS SYMBOL MEANS “DO NOT PLACE THE UNIT ON

INFLAMMABLE SURFACES”

UV

THIS SYMBOL MEANS “RADIATION FROM THIS LAMP

CAN CAUSE DAMAGE TO EYES AND SKIN”

THIS SYMBOL INDICATES THE MINIMUM DISTANCE TO

BE KEPT BETWEEN THE DEVICE AND THE LIT OBJECT

2M

2- GENERAL WARNING

Read the instruction contained in this user manual carefully, as they give important information regarding safety during installation , use and maintenance.

The device is not for domestic use and must be installed by a qualified electrician or experienced person.

Always disconnect the device from the mains before replacing the lamp.

The lamp must be replaced if it has been damaged or deformed by prolonged use or overheating.

The device must always be equipped with an efficient ground connection.

3- GENERAL WARRANTY CONDITIONS

The unit is guaranteed for 24 months from the date of purchase against manufacturing material defects.

5

XR2000 SPOT


The XR2000 SPOT is a brand new moving head fitted with a 700W discharge lamp, which delivers a massive 27.000 Lux at 5 m (10°).

The XR2000 SPOT is fitted with a Philips MSR Gold 700/2 Fastfit lamp (50.000 Lumens) combined with a dichroic parabolic reflector.

The XR2000 SPOT is one of the most complete moving heads in the 700W range and is particularly suitable for all professional applications, both mobile (concerts, shows, tours, special events) and fixed

(clubs and other venues), requiring a light with extremely high luminous output and versatility of functions.

The XR2000 SPOT in fact features a very flexible colour generation, thanks to two colour wheels with 7 colours each, with linear selection for perfect 2-colour beams, and also 2 colour conversion filters

(3200°K and 5600°K).

The XR2000 SPOT incorporates also motorized focussing, motorized iris, motorized linear zoom (8°-

30°), 3-facet rotating prism, 1 wash effect filter.

2 gobo wheels are available, featuring respectively: 7 rotating and 16 bit indexable gobos

(interchangeable); 8 fixed gobos (interchangeable).

The XR2000 SPOT also includes a new Pan / Tilt locking system with recessed buttons and electronic ballast.

The XR2000 SPOT is the ideal moving head as well for all applications in which noiseless operation is required, thanks to its silent internal ventilation system and silent pan/tilt operation.

XR2000 SPOT (Cod. 03.MS009.EB.L )

• Electronic ballast 90-260V 50/60 Hz • Black colour

Also available in white (RAL 9003) colour on demand.

Lamp

Lamp: Philips MSR Gold 700/2 Fastfit

Automatic switching ON of lamp in case of accidental switching OFF.

Lamp ON/OFF via DMX; Reset via DMX.

Optical group

64.300 Lux at 5 m (8° beam angle)

Dichroic glass reflecto

Focus

Motorized focus

Iris

Motorized iris (16 bit)

Zoom

Motorized zoom (8°- 30°)

6

XR2000 SPOT


Dimmer / shutter / strobo

Linear dimmer

Shutter

Strobe from 0,85 flash/sec to 6,75 flash/sec

Power saving mode (the lamp dims to 50% six seconds after shutter closure)

Colours

2 Colour wheels (7 colours + open with linear selection)

3200°K and 5600°K colour conversion filters

Colour change with blackout sync; rainbow effect

Gobos

2 gobo wheels: 1 rotating (7 indexable 16 bit gobos + open) and 1 fixed (8 gobos + open)

Extractable gobo holders for both wheels

Gobo change with synchronized blackout

Gobo scrolling; Gobo shake

Effects

Indexable prism rotating in both directions (3-facet)

Wash effect filter

Pan / Tilt

Pan 540° (3,9 sec.)

Tilt 270° (2,6 sec.)

16-bit resolution

2-Speed function (2 selectable pan/tilt speeds); extremely smooth and precise movements even at the highest speeds

Pan / Tilt locking system with recessed buttons

Automatic Pan/Tilt repositioning in case of knocks

25 DMX channels (Default)

Internal operating system updatable via DMX

Connections

4 XLR connectors (3-pole In and Out; 5-pole In and Out) by Neutrik

POWERCONN connector by Neutrik

Power supply

Electronic ballast: 90 - 260 V (50/60 Hz)

Power consumption: 820 W

Standard accessories

2 x “C” GQuick clamps with “fastlock” connection

Thermal

Operating ambient temperature: -10° / 40°

Weight

43 Kg (electronic ballast)


Dimensions

Packaging Dimensions (LxWxH)

670 x 550 x 730 mm

Weight: 48 Kg

7

Unit Dimensions (LxWxH)

555x510x825mm

Weight: 43 Kg

XR2000 SPOT

5- ACCESSORIES

As standard

•1 x MSR Gold 700/2 Fastfit lamp

•1 x POWERCONN male cable connector (cod. 0520P014)

•1 x XLR 5 Pins male cable connector (cod. 0508B028)

•1 x XLR 5 Pins female cable connector (cod. 0508B027)

•2 x “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)

• User’s manual

Optional (on request)

• Wireless DMX receiver card (cod. 03.LA.012)

• “C” Clamp G60 black (max. load 50Kg) (cod. 0521A004)

• “C” Clamp G60 chrome (max. load. 50Kg) (cod. 0521A004.20)

• “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)

• “C” Clamp G100 black / professional (max. load. 200Kg) (cod. 0521A015)

• Omega clamp with “Fast Lock” connection 1⁄4 turn (cod. 02K00467)

• Safety wire (3mm x 60 cm), ring spring catch, max. capacity load 60Kg (cod. 0521A010)

8

XR2000 SPOT

6- IMPORTANT SAFETY INFORMATION

6.1 Fire prevention:

XR2000 SPOT uses a PHILIPS /2

The use of any other alternative lamp is not recommended and will null and void the fixture's warranty.

-Never locate the fixture on any flammable surface.

-Minimum distance from flammable materials: 1.5 MT.

F

-Minimum distance from the closest illuminable surface: 2 MT.

2M

-Replace any blown or damaged fuses only with those of identical value. Refer to the wiring diagram if there is any doubt.

-Connect the projector to mains power via a thermal magnetic circuit breaker.

6.2 Prevention of electric shock:

-High voltage is present inside the unit. Unplug the unit prior to performing any function which involves touching the inside of the moving head, including lamp replacement.

-The level of technology inherent in the XR2000 SPOT requires the assistance of specialised personnel for all servicing. Please refer to an authorised DTS service centre.

-A good earth connection is essential for proper functioning of the projector.

-Never connect the unit without proper earth connection.

-The fixture should be located in places with a good air ventilation.

6.3 Protection against ultraviolet radiation:

UV

-Never turn on the lamp if any of the lenses, filters or ABS covering are damaged. Their respective shielding functions will only operate efficiently if they are in perfect working order.

-Never look directly the lamp when it is on.

6.4 Safety:

!

-The projector should always be installed with bolts, clamps and other tools that are capable of supporting the weight of the unit.

-Always use a second safety cable to sustain the weight of the unit in case of the failure of the main fixing point.

-The external surface of the unit, at various points, may exceed 70°C. Never handle the unit until at least 10 minutes have elapsed since the lamp was turned off.

-Always replace the lamp if any physical damage is evident.

-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient temperature should not exceed 40°C.

-A hot lamp may explode, so always wait for at least 10 minutes prior to attempting to replace the lamp.

-Always wear suitable hand protection when handling the lamp.

6.5 Level of protection against the penetration of solid and liquid objects:

!

-The projector is classified as an ordinary appliance and its protection level against the penetration of solid and liquid objects is IP 20.

For outdoor use, D.T.S. reccomend the use of the dedicated raincovers:

• Raincover for XR2000 base (top) (cod. 03.MA009)

• Raincover for XR2000 base (bottom) (cod. 03.MA010)

9

XR2000 SPOT

7- MOUNTING THE LAMPS

Warning: Switch off the unit before replacing the lamp.

Philips MSR Gold 700/2 Fastfit

Power 700W

Luminous flux 50,000 lm

Colour temperature 7.500°K

Lampbase PGJX50

Rated life 750 hours

1) Using a screwdriver, loose the 3 screws A, B, C, (photo 1) and remove the metal cover .

Photo 1 Photo 2 Photo 3 Photo 4

2) Insert the lamp (photo2).

3)Rotate the lamp 1/4 turn clockwise (photo 3 and 4).

The lamp used on XR2000 SPOT is made in quartz glass and should be handled with care. Always follow the instructions supplied in the lamp's packaging. Never touch the glass directly but use the tissue provided in the lamp’s packaging. The PGJX50 lamp socket is not symmetrical.

DO NOT USE UNDUE FORCE ON THE GLASS. In case of difficulty, read again the instructions and repeat the procedure.

4) Replace the metal cover and tighten the screws A,B,C, which were previously removed.

WARNING: Never look directly at the lamp when it’s lit.

Discharge lamps emits UV rays; radiation from this lamp can cause damage to eyes and skin.

UV

7.1 Lamp alignment

Attention: we recommend to align the lamp in the optical system to avoid overheating of the dichroic filters and other components inside the unit. The lamp alignment is also essential to obtain the maximum unifirmity and luminous performance by the projection.

Photo 5 Normal Hot Spot

Lamp

Alignment

1) Mount the fixture in an orientation so that it may be squarely projected onto a smooth white surface no less than 3 meters away. 2) Using a console or the menu system, focus an open (white) beam onto the surface and observe the beam. 3) Using a phillips-head screw driver, rotate the 3 adjusters X, Y and

Z (photo 5) until you achieve a uniform flat field.

When the lamp is correctly optimized, you will have an evenly projected light beam, with no shadows or zones wich are brighter than others.

10

XR2000 SPOT

8- VOLTAGE AND FREQUENCY

The XR2000 SPOT with electronic ballast can operate at 90-260 VOLT 50 or 60 Hz.

9- INSTALLATION

XR2000 SPOT may be either floor or ceiling mounted.

For floor mounting installations, the XR2000 SPOT is supplied with four rubber mounting feet on the base.

For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the mounting surface.

The supporting structure from which the unit is hung should be capable of bearing the weight of the unit, as should any clamps used to hang it. The structure should also be sufficiently rigid so as not to move or shake whilst the XR2000 SPOT is moving.

.

Eight 1/4 turn Fast Locks connections placed in the base of the unit allow to fix the XR2000 SPOT in any position, by using the two Fast Lock “C” clamps provided in the box.

240 mm

107 mm

9.1- Safety cable

We recommend the use of a safety cable connected to the XR2000 SPOT and to the suspension truss in order to avoid the fixture accidentally falling should the main fixing point fail. Make sure that the iron cable can bear the weight of the entire unit.

You may attach the safety cable to the two holes (A) located on the base of the fixture, as shown in the picture below.

A

!

9.2- Protection against liquids

The projector contains electric and electronic components which should under no circumstances come into contact with oil, water or any other liquid. The proper unit functioning would be compromised should this occur.

11

XR2000 SPOT

9.3- Movement

The projector has a maximum movement of 540° for Pan and 270° for Tilt. DO NOT place any obstructions in the path of the projector's movement.

270°

!

WARNING

Do not place any object in the path of the projector’s movement

540°

9.4- Risk of fire

Each fixture produces heat and must be installed in a well-ventilated place. The minimum recommended distance from flammable material is 1 MT.

F

Minimum distance from the object being illuminated is 2 MT.

2M

9.5- Forced ventilation

You will note, on inspection, that the unit features various air inlets and cooling fans located on both the base and head of the fixture. These should, under no circumstances, be blocked or obstructed whilst the projector is in operation.

Doing so could cause the fixture to seriously overheat thereby compromising its proper operation.

9.6- Ambient temperature

The projector should never be installed in places that lack a constant air flow. The ambient temperature should NOT exceed 40°C.

10- MAINS CONNECTION

XR2000 SPOT with electronic ballast operate at 90-260 VOLT 50-60 Hz.

Prior to connecting the unit to your mains supply, ensure that the model in your possession correctly matches the mains supply available. For connection purposes, ensure that your plug is capable of supporting 8 amps at 230V,

Or 16 amps at 100-120 V

Strict adherence to regulatory norms is strongly recommended.

Electronic ballast

90-260V 50 / 60Hz

10.1- Protection

The use of a thermal magnetic circuit breaker is recommended for each XR2000 SPOT.

A good earth connection is essential for the correct operation of the projector.

!

12

XR2000 SPOT

11- DMX SIGNAL CONNECTION

The unit operates using the digital DMX 512 (1990) signal. Connection between the mixer and the projector or between projectors must be carried out using a two pair screened ø 0.5 mm cable and a XLR

5 or 3 pins connector. Ensure that the conductors do not touch each other. Do not connect the cable ground to the XLR chassy

The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and connect it to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the second one.

This way, all the projectors are cascade connected.

NB. If the display showing the DMX address flashes, then one of the following errors has occurred:

- DMX signal not present

- DMX address not valid

- DMX reception problem

5

4

CONTROLLER

S T A N D A R D

D M X 5 1 2

1

2

1=GND

2=DATA-

3=DATA+

3

For Installations where long distance DMX cable connections are needed, we suggest to use a DMX terminator.

The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor

Between pin 2 and 3.

The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.

5

4

3

2

1

OUT

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

PIN 3

120 ohm

PIN 2

13

XR2000 SPOT

11.1-DMX Addresses

XR2000 SPOT can be controlled with 25 (default) or 18 OR 26 DMX channels.

If you want to use the unit in 25 channels mode (default), set the following addresses on the mixer:

Projector 1 A001

Projector 2 A026

Projector 3 A051

…..

A….

projector 6 A126

If you want to select the next projector, just add “25”

11.2-Selecting the DMX address

1) Press the UP-DOWN key until you reach the required DMX channel. The numbers on the display will start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the projector is now setted to the new DMX address.

TRICKS:

if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get a faster selection.

12 FIRMWARE UPDATING

Warning:

This procedure require a base knolewge of computer applications and Windows

Hyperterminal program.

Please refer to an authorised DTS service centre.

To update the software version of the XR2000 SPOT you need:

D.T.S. RED BOX interface (D.T.S. Code: 03.LA.008).

USB-DMX Driver for the D.T.S. RED BOX interface .

(The driver and the installation procedure are available in our web site www.dts-lighting.it)

Updating the software version.

Please follow the procedure below to perform the update:

1. Install the D.T.S. RED BOX USB-DMX driver on the PC you will use to update the unit software.

2. Connect the D.T.S. RED BOX interface to the PC by using a USB cable.

3. Connect the D.T.S. RED BOX interface to the fixture by using a DMX cable.

4. Download the new software version into the unit by using Windows Hyperterminal program.

It will be possible to download the software from the reserved area of D.T.S. web site:

www.dts-lighting.it.

!

14

XR2000 SPOT


DMX OUT

DISPLAY

DMX IN

DMX IN FUSE 16A T 5X20

DMX OUT

MENU

ENTER

UP

DOWN

MAINS

Electronic ballast

90-260V 50 / 60Hz

DISPLAY FUNCTIONS

The XR2000 SPOT display panel shows all the available functions . Using these functions, it is possible to change some of the parameters and add some functions. Changing the DTS setting can vary the functions of the unit so that it does not respond to the DMX 512 used to control it.

Carefully follow the instructions below before carrying out any variations or selections.

NOTE: the symbol shows which key has to be pushed to obtain the desired function.

Menu

Up-Down

Pan Direction

PAN DIRECTION

This menu allows to set the Pan movement.

Normal or Reversed

ENTER Up-Down

PAN DIRECTION

NORMAL

Pan movement Normal or Reversed

Default = Normal

ENTER

MENU ENTER DOWN UP

Menu

Up-Down

Tilt Direction

TILT DIRECTION

This menu allows to set the Pan movement.

Normal or Reversed

ENTER Up-Down

TILT DIRECTION

Tilt movement Normal or Reversed

Default = Normal

NORMAL

MENU ENTER DOWN UP

ENTER

Menu

Up-Down

Pan Tilt Speed

PAN TILT SPEED

Pan Tilt Speed control (1-4)

ENTER Up-Down

PAN TILT SPEED

4

Pan Tilt Speed control

Default = 4

ENTER

MENU ENTER DOWN UP

15

XR2000 SPOT


Menu Up-Down

Display

ENTER

DISPLAY FLIP / STAND BY / CONTRAST

Up-Down

Display Flip:

Reverses display's reading depending on the mounting position

(On the ground or suspended).

Display Standby:

To turn off the display (after 5 seconds)

Or leave it always on.

Display Contrast:

Display contrast regulation (1-16)

DISPLAY

Display Flip

ON THE GROUND (Default)

SUSPENDED

ON THE GROUND

MENU ENTER DOWN UP

DISPLAY

Display Standby

OFF = Display Standby disabled

(Default)

ON = Display goes OFF after 5 seconds

OFF

MENU ENTER DOWN UP

DISPLAY

Display Contrast

1-16 (Default = 8)

ENTER

ENTER

ENTER

Menu Up-Down

DMX Mode

DMX MODE

To select DMX mode :

18 channels, 25 or 22 channels

ENTER Up-Down

8

MENU ENTER DOWN UP

DMX MODE

25 channels

DMX mode

18 channels

25 channels (Default)

26 channels

ENTER

Menu Up-Down

Lamp

LAMP

Lamp always ON, always OFF, lamp ON-OFF selectable via DMX

And lamp life time reset

ADJUST

To adjust the lamp with no mixer connected.

It’s possible to set the parameters for

PAN-TILT and ZOOM

ENTER Up-Down

MENU ENTER DOWN UP

LAMP

MENU ENTER DOWN UP

LAMP

BY DMX = ON / OFF via DMX (default)

ALWAYS ON = Forced ON

ALWAYS OFF = Forced OFF

RESET COUNTER = Lamp life time reset

ENTER

LAMP ADJUST = To adjust the lamp with no mixer connected.

It’s possible to set the parameters for

PAN-TILT and ZOOM

ENTER

Menu

Up-Down

Reset

RESET

Reset via DMX ENABLED / DISABLED and unit reset

ENTER Up-Down

MENU ENTER DOWN UP

RESET

BY DMX

ENABLED

ENABLED = Reset via DMX enabled

(Default)

DISABLED = Reset via DMX disabled

NOW = Unit motors reset

ENTER

MENU ENTER DOWN UP

16


Menu

Up-Down

Fan Speed

FAN SPEED

Fan Speed control

ENTER Up-Down

FAN SPEED

5

MENU ENTER DOWN UP

Fan speed control

1-5 (Default = 5)

XR2000 SPOT

ENTER

Menu Up-Down

Gobo Rotation

ENTER Up-Down

GOBO ROTATION

Gobo rotation control the Rotating speed of gobo

GOBO ROTATION

During gobo scrolling

OFF

ON

OFF = (Default)

MENU ENTER DOWN UP

ENTER

Menu Up-Down

System info

ENTER

SYSTEM INFO

Lamp life time, lamp strikes, unit life time, 8 motors card software version, Pan&Tilt card software version and unit model

Up-Down

SYSTEM INFO

LAMP LIFE:0000H STRIKE:001

UNIT LIFE: 0010H

8M R.20

PT R.19

MODEL: XR2000 BEAM

MENU ENTER DOWN UP

SYSTEM INFO

Lamp life time, lamp strikes, unit life time, 8 motors card software version, Pan&Tilt card software version and unit model

ENTER

Menu Up-Down

Reserved

RESERVED

Pan lock-Tilt lock

Pan free-Tilt free

System Reboot

(Code = 100)

ENTER Up-Down

RESERVED

ENTER CODE

000

MENU ENTER DOWN UP

PAN LOCK

NO

Pan Lock = Lock the Pan to the desired value

Tilt Lock = Lock the Tilt to the desired value

Pan Free = Remove power to Pan motor

Tilt Free = Remove power to Tilt motor

System Reboot = Unit Reboot without needing of turning OFF the unit

ENTER

MENU ENTER DOWN UP

Menu Up-Down

Default

DEFAULT

To restore main settings

ENTER Up-Down

DEFAULT

RESTORE MAIN SETTINGS

Default

To restore main settings

ENTER

MENU ENTER DOWN UP

DEFAULT

RESTORE MAIN SETTINGS

SURE?

PRESS ENTER TO CONFORM

PRESS MENU TO CANCEL

MENU ENTER DOWN UP

17

XR2000 SPOT

14- ERROR MESSAGES

ERROR

EFFECT

MENU ENTER DOWN UP

EFFECT WHEEL ERROR

ERROR

PAN

MENU ENTER DOWN UP

PAN REPOSITIONING

ENCODER ERROR

ERROR

DMX ADDRESS

MENU ENTER DOWN UP

DMX ADDRESS

ERROR

ERROR

GOBO

MENU ENTER DOWN UP

GOBO WHEEL ERROR

ERROR

TILT

MENU ENTER DOWN UP

TILT REPOSITIONING

ENCODER ERROR

ERROR

GOBO INDEX

MENU ENTER DOWN UP

GOBO POSITION

ERROR

ERROR

INTERNAL BUS

MENU ENTER DOWN UP

COMMUNICATION

PROBLEM BETWEEN 8

MOTORS CARD AND

PAN&TILT CARD

ERROR

FIXED GOBO

MENU ENTER DOWN UP

FIXED GOBO WHEEL

ERROR

ERROR

IRIS

MENU ENTER DOWN UP

IRIS ERROR

ERROR

COLOUR 1

MENU ENTER DOWN UP

COLOUR WHEEL 1

POSITION ERROR

ERROR

COLOUR 2

MENU ENTER DOWN UP

COLOUR WHEEL 2

POSITION ERROR

ERROR

FOCUS

MENU ENTER DOWN UP

FOCUS ERROR

ERROR

ZOOM

MENU ENTER DOWN UP

ZOOM ERROR

18

XR2000 SPOT

15- HIDDEN MENU

For technical personnel only.

To operate this menu:

-Connect the projector to the DMX controller (DMX SIGNAL MUST BE CORRECTLY RECEIVED)

Reset the XR2000 SPOT (reset from the MENU, not from the DMX controller!).

While reset is running, press the MENU and ENTER keys at the same time.

CALIBRATION

MOTORS ALIGNMENT

PAN

134

MENU ENTER DOWN UP

ELECTRONIC

CALIBRATION OF THE

MOTORS

MIN LAMP POW.

1=65% 100=100%

10

MENU ENTER DOWN UP

LAMP POWER WHEN

DIMMER CLOSED

DEFAULT CAL

SET ALL MOTORS AT 128

MENU ENTER DOWN UP

RESET EEPROM.

RESET ALL SETTINGS

TO 128 VALUE

EXIT TO MAIN

MENU ENTER DOWN UP

EXIT FROM HIDDEN

MENU

FANS SPEED

ONLY AT MIN LAMP POWER

3

MENU ENTER DOWN UP

FAN SPEED WHEN

DIMMER CLOSED

15.1 Calibration

CALIBRATION


PAN

134

MENU ENTER DOWN UP

PAN ALIGNMENT

To align Pan position

CALIBRATION


COLOUR 1

151

COLOUR WHEEL 1

ALIGNMENT

CALIBRATION


GOBO INDEX

141

MENU ENTER DOWN UP

GOBO WHEEL INDEX ALIGNMENT

To align Gobo wheel Index

CALIBRATION


EFFECTS

85

MENU ENTER DOWN UP

EFFECTS ALIGNMENT

To align EFFECTS

CALIBRATION


DIFFUSER

85

MENU ENTER DOWN UP

DIFFUSER ALIGNMENT

To align DIFFUSER

19

CALIBRATION


TILT

167

MENU ENTER DOWN UP

TILT ALIGNMENT

To align Tilt position

CALIBRATION


COLOUR 2

151

COLOUR WHEEL 2

ALIGNMENT

CALIBRATION


FIXED GOBO

151

MENU ENTER DOWN UP

G O B O F I X E D W H E E L

ALIGNMENT

To align Gobo wheel

CALIBRATION


FOCUS

151

MENU ENTER DOWN UP

FOCUS ALIGNMENT

To alignFOCUS

XR2000 SPOT

CALIBRATION


SHUTTER

145

MENU ENTER DOWN UP

SHUTTER ALIGNMENT

To align Shutter blades

CALIBRATION


GOBO

151

MENU ENTER DOWN UP

GOBO WHEEL ALIGNMENT

To align Gobo wheel

CALIBRATION


IRIS

85

MENU ENTER DOWN UP

IRIS ALIGNMENT

To align IRIS

CALIBRATION


ZOOM

151

MENU ENTER DOWN UP

ZOOM ALIGNMENT

To align ZOOM

20

XR2000 SPOT

Calibration mode

16- PAN & TILT SPEED (default: 4)

You can set the PAN and TILT motors at high speed on your XR2000 SPOT.

Press menu until you see PAN TILT SPEED.

Press ENTER and select a speed with UP-DOWN (there are 4 speeds). Confirm by pressing ENTER.

17- FAN SPEED ( default: 5)

Fan speed regulation makes it possible to reduce fan noise. However, the ambient temperature must be less than 35° C.

21

XR2000 SPOT

18- OPENING THE PROJECTOR HOUSING

It is possible to inspect the inside of the projector by removing the cover as indicated below.

ATTENTION

REMOVE MAINS POWER PRIOR TO ACCESSING THE PROJECTOR’S INTERNAL COMPONENTS.

1) Loosen the 3 screws which fix the head covers (photo 1) .

2) Once unscrewed, simply lift the covers to access the internal components (photo 2).

Photo 1

19- REPLACING GOBOS

Photo 2

XR2000 SPOT uses a mechanical system which allows the fixture's gobos to be removed without the use of special tools. Replacement gobos should be made of either heat resistant glass or metal.

An ever-increasing range of gobos is available from your DTS sales network.

Gobo dimensions are as follows:

ø external (ED) = 27.9 mm

ø of image with defined edge (ID) = 24 mm thickness = from 0.2 to 4 mm (see catalogue)

Max thickness

4 mm

Coated side

When an object is held up the coated side of the glass gobo there is no space between the object and its reflection.

Coated side

Uncoated side

When an object is held up the uncoated side of the glass gobo there is a space between the object and its reflection.

Uncoated side

Load with coated surface toward the light source.

22

Replacing gobos on the rotating gobo wheel

When replacing gobos, ensure that the projector is switched off.

1) Open the projector housing as described on page 21.

2) Remove the gobo holder to allow easier access to the gobo (photo 1).

3) Release the gobo retaining spring and carefully remove the gobo (photo 2).

4) Reverse the procedure to install a replacement gobo.

XR2000 SPOT

Photo 2

Photo 1

20- PERIODIC CLEANING

20.1- Lenses and reflectors

Even a fine layer of dust can reduce the luminous output substantially. Regularly clean all lenses and the reflector using a soft cotton cloth, dampened with a specialist lens cleaning solution.

20.2- Fans and air passages

The fans and air passages must be cleaned approximately every 6 weeks. This periodic cleaning will depend of course, on the conditions in which the projector is operating. Suitable instruments for performing this type of maintenance are a brush and a common vacuum cleaner or an air compressor. If necessary, clean the fans and air passages more frequently.

21- PERIODIC CONTROLS

Attention

Disconnect mains power prior to removing the projector housing.

!

Lamp

The lamp should be replaced if there is any visible damage or deformation due to heat. This will help to avoid the danger of the lamp exploding.

XR2000 SPOT lamp lifespan is about 750 hours, then it is necessary to replace it.

Mechanical parts

Periodically check all mechanical parts,gears, guides, belts, etc.for wear and tear, replacing them if necessary. Periodically check the lubrication of all components, particularly the parts subject to high temperatures. If necessary, lubricate with suitable lubricant, available from your D.T.S. distributor. Check the tension of the belts and adjust it if necessary.

Electrical components

Check all electrical components for correct earthing and proper connection of all connectors, refastening if necessary.

Fuse replacement

Locate the fuse, which protects the lamp and electronics, in the base of the XR2000 SPOT

Using a multimeter, test the condition of the fuse, replacing it with one of equivalent type if necessary.

UV

23

XR2000 SPOT

22- DMX PROTOCOL

18 CHANNELS MODE

1 PAN msb 540°

2 PAN lsb

3 TILT msb 270°

4

5

6

TILT lsb

SPEED MOVEMENT

DIMMER

7

8

SHUTTER

COLOUR 1

9 COLOUR 2

10 ROTATING GOBO WHEEL

11 GOBO ROTATION / INDEX

12 FIXED GOBO WHEEL

13 IRIS

14 EFFECTS

15 EFFECTS ROTATION

16 FOCUS

17 ZOOM

18 LAMP ON-OFF / RESET

DMX CHANNEL

1

Parameter:

PAN msb

DMX CHANNEL

2

Parameter:

PAN lsb

DMX CHANNEL

3

Parameter:

TILT msb

DMX CHANNEL

4

Parameter:

TILT lsb

DMX CHANNEL

5

Parameter:

SPEED MOVEMENT

DMX range

Value

0-10

11-25

26-127

Mid point

Move range

DMX value

(degrees)

Mode Option

128-247

248-255

Function

Standard

Fast movement

Vector mode from fast to slow

Variable time reaction to

DMX signal ( fast to slow)

Silent Mode

DMX CHANNEL

6

Parameter:

DIMMER

DMX range

Value

0-7

8-255

Mid point

DMX value

Move range

(degrees)

Mode Option Function

Black-out

Proportional dimmer

24

XR2000 SPOT

DMX CHANNEL

7

Parameter:

SHUTTER

DMX range

Value

0-19

20-39

40-59

60-79

80-89

90-99

100-109

110 -119

120-129

130-139

140-149

150-159

160-169

170-179

180-189

190-199

200-209

210-219

220-227

228-233

Mid point

DMX value

Move range

(degrees)

Mode

234-255

DMX CHANNEL

8

Parameter:

COLOUR 1

DMX range

Value

0-11

12-23

24-35

36-47

48-59

60-71

72-83

84-95

96-107

108-119

120-131

132-143

144-155

Mid point

DMX value

Move range

(degrees)

156-167

168-179

Mode

Option Function

Black-out

Open

Black-out

Random Strobe

Strobe speed 1 min. (0,85 Hz)

Strobe speed 2 (1,4 Hz)

Strobe speed 3 (2 HZ)


Strobe speed 5 (5 Hz)

Strobe speed 6 max. (6,75 Hz)

Pulse open speed 1 min.

Pulse open speed 2


Pulse open speed 4 max.

Pulse closed speed 1 min.

Pulse closed speed 2


Pulse closed speed 4 max.

Colour and Gobo in black-out

Pan and Tilt in black-out

Open

Option Function

Colour1

Bicolour ½

Colour2

Bicolour 2/3

Colour3

Bicolour 3/4

Colour4

Bicolour 4/5

Colour5

Bicolour 5/6

Colour6

Bicolour 6/7

Colour7

Bicolour 7/8

Colour8

180-197

198-200

201-203

204-206

207-209

210-212

213-215

216-218

219-221

222-224

225-228

229-231

232-234

235-237

238-240

241-243

244-246

247-249

250-252

253-255

DMX CHANNEL

9

Parameter:

COLOUR 2

DMX range

Value

0-11

12-23

24-35

36-47

48-59

60-71

72-83

84-95

96-107

108-119

120-131

132-143

144-155

Mid point

DMX value

Move range

(degrees)

156-167

168-179

Mode

25

Option

XR2000 SPOT

Bicolour 8/1

Right rotation speed 9 max.

Right rotation speed 8







Right rotation speed 1 min.

Stop

Left rotation speed 1 min.

Left rotation speed 2







Left rotation speed 9 max.

Function

Colour1

Bicolour ½

Colour2

Bicolour 2/3

Colour3

Bicolour 3/4

Colour4

Bicolour 4/5

Colour5

Bicolour 5/6

Colour6

Bicolour 6/7

Colour7

Bicolour 7/8

Colour8

26

XR2000 SPOT

180-197

198-200

201-203

204-206

207-209

210-212

213-215

216-218

219-221

222-224

225-228

229-231

232-234

235-237

238-240

241-243

244-246

247-249

250-252

253-255

DMX CHANNEL

Bicolour 8/1

Right rotation speed 9 max.








Right rotation speed 1 min.

Stop

Left rotation speed 1 min.








Left rotation speed 9 max.

10

Parameter:

ROTATING GOBO WHEEL

DMX range

Value

0-25

26-51

Mid point

DMX value

52-77

78-103

104-129

130-155

156-181

182-207

208-213

214-219

220-225

226-231

232-237

238-243

244-249

250-255

Move range

(degrees)


Open

Gobo 1

Gobo 2

Gobo 3

Gobo 4

Gobo 5

Gobo 6

Gobo 7

Speed rotation 1 min.

Speed rotation 2

Speed rotation

Speed rotation

3

4




Speed rotation 8 max.

DMX CHANNEL

11

Parameter:

ROTATING GOBO WHEEL ROTATION/INDEX

DMX range

Value

0-127

128-180

181-202

203-255

Mid point

DMX value

Move range

(degrees)


Proportional index 0° / 360°

Left rotation

Stop

Right rotation

DMX CHANNEL

12

Parameter:

GOBO 2

DMX range

Value

0-22

23-45

46-68

Mid point

DMX value

69-91

92-114

115-137

138-160

161-183

184-207

208-213

214-219

220-225

226-231

232-237

238-243

244-255

Move range

(degrees)

Mode

27

Option

XR2000 SPOT

Function

Open

Gobo 1

Gobo 2

Gobo 3

Gobo 4

Gobo 5

Gobo 6

Gobo 7

Gobo 8

Speed rotation

Speed rotation

1 min

2





Speed rotation 7 max

DMX CHANNEL

13

Parameter:

IRIS

DMX range

Value

000-005

006-159

Mid point

DMX value

160-171

172-199

200-227

228-255

Move range

(degrees)

DMX CHANNEL

14

DMX range

Value

000-085

086-171

Mid point

DMX value

172-255

Parameter:

EFFECTS

Move range

(degrees)

Mode


Open

Linear Iris from Open to Closed

Closed

Iris pulse at different speeds from Max to Min

Iris pulse with flash closing from Min to Max

Iris pulse with flash openig from Min to Max

Option Function

No effect

3 facet prism

Frost

DMX CHANNEL

15

28

Parameter:

EFFECTS ROTATION

DMX range

Value

0-009

10 -127

128 -137

138 -255

Mid point

DMX value

Move range

(degrees)

Mode

XR2000 SPOT

Option Function

Stop

Left rotation from fast to slow

Stop

Right rotation from slow to fast

DMX CHANNEL

16

Parameter:

FOCUS

DMX range

Value

0-255

Mid point

DMX value

Move range

(degrees)


Linear focus

DMX CHANNEL

DMX range

Value

0-255

17

Parameter:

ZOOM

Mid point

DMX value

Move range

(degrees)


Linear zoom

DMX CHANNEL

18

Parameter:

RESET / LAMP

DMX range

Value

0-9

10-60

61-129

130-179

180-200

201-239

240-255

Mid point

DMX value

Move range

(degrees)


No Effect

Lamp OFF (activ.after 3 seconds)

No Effect

Lamp ON (activ.after 3 seconds)

No Effect

Internal motor reset

Total Reset

29

XR2000 SPOT

25 CHANNELS MODE (DEFAULT)

5

6

7

8

1

2

3

4

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

PAN msb 540°

PAN lsb

TILT msb 270°

TILT lsb

SPEED MOVEMENT

DIMMER

SHUTTER

COLOUR 1

COLOUR 1 MODE

COLOUR 2

COLOUR 2 MODE

GOBO 1

GOBO 1 MODE

GOBO 1 ROTATION/INDEX COARSE

GOBO 1 INDEX FINE 16 bit

GOBO 1 SHAKE

GOBO 2

GOBO 2 SHAKE

IRIS

IRIS MACROS

EFFECTS


FOCUS

ZOOM

LAMP ON/OFF - RESET

DMX CHANNEL

DMX CHANNEL

DMX CHANNEL

DMX CHANNEL

DMX CHANNEL

1

2

3

4

5

Parameter:

Parameter:

Parameter:

PAN msb

PAN lsb

TILT msb

Parameter:

TILT lsb

Parameter:

SPEED MOVEMENT

DMX range

Value

0-10

11-25

26-127

Mid point

Move range

DMX value

(degrees)

128-247

248-255


Standard

Fast movement

Vector mode from fast to slow

Variable time reaction to

DMX signal ( fast to slow)

Silent movement

30

XR2000 SPOT

DMX CHANNEL

6

Parameter:

DIMMER

DMX range

Value

0-7

8-255

Mid point

DMX value

Move range

(degrees)

Mode

DMX CHANNEL

7

Parameter:

SHUTTER

DMX range

Value

0-19

20-39

40-59

60-79

80-89

90-99

100-109

110 -119

120-129

130-139

140-149

150-159

160-169

170-179

180-189

190-199

200-209

210-219

220-227

228-233

234-255

Mid point

DMX value

Move range

(degrees)

Mode

DMX CHANNEL

8

Parameter:

COLOUR 1

Option

Option

Function

Black-out

Proportional dimmer

Function

Black-out

Open

Black-out

Random Strobe

Strobe speed 1 min. (0,85 Hz)


Strobe speed 3 (2 HZ)


Strobe speed 5 (5 Hz)

Strobe speed 6 max. (6,75 Hz)


Pulse open speed 1 min.


Pulse open speed 4 max.

Pulse closed speed 1 min.



Pulse closed speed 4 max.

Colour and Gobo in black-out

Pan and Tilt in black-out

Open

DMX range

Value

Mid point

DMX value

0-31

32 -63

64-95

96-127

128-159

160-191

192-223

224-255

Move range

(degrees)


IF CHANNEL 9 = FULL COLOUR (Dmx range value 0 - 63)

Colour1

Colour2

Colour3

Colour4

Colour5

Colour6

Colour7

Colour8

31

XR2000 SPOT

DMX CHANNEL

8

Parameter:

COLOUR 1

DMX range

Value

Mid point

DMX value

Move range

(degrees)


IF CHANNEL 9 = HALF COLOUR (Dmx range value 64 - 127)

0-27

28-55

56-83

84-111

112-139

140-167

168-195

196-223

224-255

Colour 1

Bicolour 1/ 2

Bicolour 2/ 3

Bicolour 3/ 4

Bicolour 4/ 5

Bicolour 5/ 6

Bicolour 6/ 7

Bicolour 7/ 8

Bicolour 8/ 1

0-10

11-255

0-9

10-127

128-137

138-255

IF CHANNEL 9 = PROPORTIONAL COLOUR (Dmx range value 128 - 191)

No Colour

Proportional colour

IF CHANNEL 9 = RAINBOW (Dmx range value 192 - 255)

No Colour

Right Rot.Speed from Max to Min

Stop

Left Rot.speed from Min to Max

DMX CHANNEL

9

Parameter:

COLOUR 1 MODE

DMX range

Value

0-63

64-127

128-191

192-255

Mid point

DMX value

Move range

(degrees)

DMX CHANNEL

10

Parameter:

COLOUR 2


Full Colour

Half Colour

Proportional Colour

Rainbow

DMX range

Value

Mid point

DMX value

0-31

32-63

64-95

96-127

128-159

160-191

192-223

224-255

Move range

(degrees)


IF CHANNEL 11 = FULL COLOUR (Dmx range value 0 - 63)

Colour1

Colour2

Colour3

Colour4

Colour5

Colour6

Colour7

Colour8

32

XR2000 SPOT

DMX CHANNEL

10

Parameter:

COLOUR 2

DMX range

Value

Mid point

DMX value

Move range

(degrees)


IF CHANNEL 11 = HALF COLOUR (Dmx range value 64 - 127)

0-27

28-55

56-83

84-111

112-139

140-167

168-195

196-223

224-255

234-255

Colour 1

Bicolour 1 /2

Bicolour 2/3

Bicolour 3/4

Bicolour 4/5

Bicolour 5/6

Bicolour 6/7

Bicolour 7/8

Bicolour 8/9

Bicolour 9/1

IF CHANNEL 11 = PROPORTIONAL COLOUR (Dmx range value 128 - 191)

0-10

11-255

No Colour

Proportional colour

IF CHANNEL 11 = RAINBOW (Dmx range value 192 - 255)

0-9

10-127

128-137

138-255

No Colour

Right Rot.Speed from Max to Min

Stop

Left Rot.speed from Min to Max

DMX CHANNEL

11

Parameter:

COLOUR 2 MODE

DMX range

Value

0-63

64-127

128-191

192-255

Mid point

DMX value

DMX CHANNEL

Move range

(degrees)

12

Parameter:

GOBO 1

Mode

DMX range

Value

0-25

26-51

52-77

78-103

104-129

130-155

156-181

182-207

208-213

Mid point

DMX value

Move range

(degrees)

Mode

Option

Option

Function

Full Colour

Half Colour

Proportional Colour

Rainbow

Function

Open

Gobo 1

Gobo 2

Gobo 3

Gobo 4

Gobo 5

Gobo 6

Gobo 7

Rotation speed 1 min.

33

XR2000 SPOT

DMX CHANNEL

12

Parameter:

GOBO 1

DMX range

Value

214-219

220-225

226-231

232-237

238-243

244-249

250-255

Mid point

DMX value

DMX CHANNEL

Move range

(degrees)

13

Parameter:

Mode

GOBO 1 MODE

Option Function

Rotation speed 2






Rotation speed 8 Max

DMX range

Value

0-127

128-255

Mid point

DMX value

DMX CHANNEL

14

Move range

(degrees)

Parameter:


Gobo Rotation Mode

Gobo Index Mode

GOBO 1 ROTATION/GOBO 1 INDEX COARSE

DMX range

Value

Mid point

DMX value

Move range

(degrees)


IF CHANNEL 13 = Gobo Rotation Mode (Dmx range value 0 - 127)

0-9

10-127

128-137

138-255

0-255

DMX CHANNEL

Stop

SX Rot. Prop. Speed Max to Min

Stop

DX Rot. Prop. Speed Min to Max

IF CHANNEL 13 = Gobo Index Mode (Dmx range value 128 - 255)

Gobo index Coarse

15

Parameter:

GOBO 1 INDEX FINE

DMX range

Value

0-255

Mid point

DMX value

DMX CHANNEL

Move range

(degrees)

16

Parameter:

Mode

GOBO 1 SHAKE

Option

DMX range

Value

0-9

10-22

23-35

36-48

Mid point

DMX value

Move range

(degrees)

Mode Option

Function

Gobo Index Fine

Function

Stop

Gobo Shake R-L Speed 1 Min.

Gobo Shake R-L Speed 2


34

XR2000 SPOT

DMX CHANNEL

16

Parameter:

GOBO 1 SHAKE

DMX range

Value

49-61

62-74

75-87

88-100

101-113

114-126

127-138

139-151

152-164

165-177

178-190

191-203

204-216

217-229

230-242

243-255

Mid point

DMX value

DMX CHANNEL

17

Parameter:

GOBO 2

Move range

(degrees)

Mode

DMX range

Value

0-22

23-45

46-68

69-91

Mid point

DMX value

92-114

115 -137

138-160

161-183

184-207

208-213

214-219

220-225

226-231

232-237

238-243

244-255

Move range

(degrees)

Mode Option

Option Function






Gobo Shake R-L Speed 9 Max

Stop

Gobo Shake L-R Speed 1 Min

Gobo Shake L-R Speed 2







Gobo Shake L-R Speed 9 Max

Function

Open

Gobo 1

Gobo 2

Gobo 3

Gobo 4

Gobo 5

Gobo 6

Gobo 7

Gobo 8

Speed rotation

Speed rotation

1 min

2





Speed rotation 7 max

35

XR2000 SPOT

DMX CHANNEL

18

Parameter:

GOBO 2 SHAKE

DMX range

Value

0-9

10-22

23-35

36-48

49-61

62-74

75-87

88-100

101-113

114-126

127-138

139-151

152-164

165-177

178-190

191-203

204-216

217-229

230-242

243-255

DMX CHANNEL

Mid point

DMX value

19

Move range

(degrees)

Parameter:

IRIS

DMX range

Value

6-255

Mid point

DMX value

Move range

(degrees)

Mode

Mode

Option Function

Stop

Gobo Shake R-L Speed 1 Min.








Gobo Shake R-L Speed 9 Max

Stop

Gobo Shake L-R Speed 1 Min








Gobo Shake L-R Speed 9 Max

Option

Open

Function

DMX CHANNEL

20

Parameter:

IRIS MACROS

DMX range

Value

0-9

10-91

92-173

174-255

Mid point

DMX value

Move range

(degrees)


No effect

Iris pulse at different speeds from Min to Max

Iris pulse with flash closing from Min to Max

Iris pulse with flash opening from Min to Max

DMX CHANNEL

21

DMX range

Value

0-085

86-171

172-255

Mid point

DMX value

Parameter:

EFFECTS

Move range

(degrees)

Mode

36

Option

XR2000 SPOT

Function

No effect

3 facet prism

Frost

DMX CHANNEL

22

Parameter:


DMX range

Value

0-9

10-127

128-143

144-255

Mid point

DMX value

Move range

(degrees)


Stop

Left Rotation from fast to slow

Stop

Right Rotation from slow to fast

DMX CHANNEL

23

DMX range

Value

0-255

Mid point

DMX value

Parameter:

FOCUS

Move range

(degrees)

Mode

DMX CHANNEL

24

DMX range

Value

Mid point

DMX value

0-255

Parameter:

ZOOM

Move range

(degrees)

DMX CHANNEL

25

Parameter:

RESET

DMX range

Value

0-9

10-60

61-129

130-179

180-200

201-239

240-255

Mid point

DMX value

Move range

(degrees)

Mode

Mode

Option

Option

Option

Function

Linear Focus

Function

Linear zoom

Function

No Effect

Lamp OFF (activ.after 3 seconds)

No Effect

Lamp ON (activ.after 3 seconds)

No Effect

Internal motor reset

Total Reset

37

15

16

17

18

19

20

21

22

23

24

25

26

8

9

4

5

6

7

26 CHANNELS MODE (SEE THE 25 CHANNELS MODE FOR DETAILS)

1

2

3

PAN msb 540°

PAN lsb

TILT msb 270°

TILT lsb

SPEED MOVEMENT

DIMMER

SHUTTER

COLOUR 1

COLOUR 1 MODE

10

11

12

13

14

COLOUR 2

COLOUR 2 MODE

GOBO 1

GOBO 1 MODE

GOBO 1 ROTATION/INDEX COARSE

GOBO 1 INDEX FINE 16 bit

GOBO 1 SHAKE

GOBO 2

GOBO 2 SHAKE

IRIS

IRIS MACROS

EFFECTS


NOT USED

FOCUS

ZOOM

LAMP ON/OFF - RESET

XR2000 SPOT

38

23- 8 MOTORS CONTROL CARD

8 MOTORS CONTROL CARD

J7 Magnetic Sensors

Connector

Line 1 Brown

Line 2 Orange

GND

ORANGE

BROWN

VCC

J26 to 6 Motors

Control card

J9 from J3 Lamp ON-OFF control card

J1 Internal DATA

Communication

Connector

From J8 Pan & Tilt card

30 VDC

+

-

XR2000 SPOT

Rotating gobo wheel

(BLACK)

Fixed gobo wheel

(DARK GREEN)

Strobe

(YELLOW)

Colour 1

(GREY)

Colour 2

(LIGHT BLUE)

Fans

Fans

24- 6 MOTORS SLAVE CONTROL CARD

39

XR2000 SPOT

J1 from 8

Motors

Control card

+

30 VDC

-

Zoom

(YELLOW)

Focus

(VIOLET)

Iris

(RED)

Effect rotation

(DARK ORANGE)

Effects

(LIGHT ORANGE)

Gobo rotation

(BROWN)

25-PAN & TILT CARD

40

XR2000 SPOT

PAN

(WHITE)

TILT

(BROWN)

GND

(BLACK)

30 VDC

(RED)

FAN

(WHITE)

ENCODER PAN

(RED)

ENCODER TILT

(ORANGE)

TO J1

DISPLAY CARD

(WHITE)

TO J1

8 MOTORS CARD

(VIOLET)

26-CABLES RESEND CARD

27-DISPLAY CARD

DMX INPUT

(WHITE)

TO J2

LAMP

ON-OFF

CARD

28-LAMP ON-OFF CONTROL CARD

J4

FROM J16

PAN&TILT

CARD

J2

J3

TO J9

ELECTRONIC

BALLAST

29- ROTATING GOBO WHEEL

4

3

41

5

2

6

XR2000 SPOT

7

GOBO 1 DICRO

1

GOBO 2 DICRO

GOBO 3 DICRO

0516G032.01

0516G032.08

0516G032.12

GOBO 4 DICRO GOBO 5 DICRO GOBO 6 DICRO

GOBO 7 DICRO

0516G032.10

0516G032.11

0516G032.03

0516G032.05

42

XR2000 SPOT

30- FIXED GOBO WHEEL

8

7

6

5

4

GOBO 1 DICRO

1

2

GOBO 2 DICRO

3

GOBO 3 METAL GOBO 4 DICRO

0516G032.06

0516G032.04

0516G032.15.M.58

0516G032.07

GOBO 5 GLASS

GOBO 6 DICRO

GOBO 7 DICRO GOBO 8 DICRO

0516G032.14

0516G032.09

0516G032.13

0516G032.02

31- COLOUR WHEEL 1

1

2

43

3

XR2000 SPOT

4

COL1

7

COL2

6

COL3

5

0507C043.D10

LAVANDER SL0064

0507C051.D10

ORANGE LW590

COL4 COL5

0507C045.D10

CYAN SW 530

COL6 COL7

0507C058.D10

PINK SL4758

0507C041.D10

DARK BLUE SW490

0507C049.D10

YELLOW LW 515

0507C047.D10

RED LW 640

32- COLOUR WHEEL 2

1

2

44

3

COL1

7

COL2

6

COL3

5

4

0507K005.D10

HALF CONV.FILTER

HOT TC3256

COL4

0507K004.D10

CONV.FILTER HOT

TC3256

COL5

0507K003.D10

CONV. FILTER COLD

DL542

COL6 COL7

0507C042.D10

GREEN WB5055

0507C038.D10

MAGENTA SL 4763

0507C053.D10

AMBER LW550

0507C046.D10

WOOD SW460

NOTES

45

NOTES

46

NOTES

47

The information contained in this publication has been carefully prepared and checked.

However, no responsibility will be taken for any errors. All rights are reserved and this document cannot be copied, photocopied or reproduced, in part or completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits described herein.

MADE IN ITALY

*0517I108*

0517I108

D.T.S. Illuminazione s.r.l - Via Fagnano Selve 10-12-14 47843 - Misano Adriatico (RN) Italy

Tel. +39 0541 611131 Fax +39 0541 611111 [email protected] www.dts-lighting.it

No results