Adash VA4Pro 4400 Vibration Analyser User Manual
Below you will find brief information for Vibration Analyser VA4Pro 4400. The device is a powerful tool for vibration analysis, featuring a variety of measurement modes, including analyser mode for standard signal analysis, runup mode for measurements during machine start-up, and a balancer mode for balancing rotating machinery. It can measure and analyze various types of vibration signals, such as acceleration, velocity, displacement, and frequency response. In addition, the VA4Pro 4400 has a built-in recorder allowing you to capture and analyze vibration data over time.
Advertisement
Advertisement
User Manual
Adash 4400 – VA4Pro
Ver. 300310
ADASH Ltd..
Content:
Adash 4400 – VA4Pro
Before Switching On ................................................................................................ 4
General information ................................................................................................. 5
The switch-on ......................................................................................................................5
Connection to the computer.................................................................................................5
The charging........................................................................................................................5
The DSP board - monitoring and reset ................................................................................6
Virtual analysers ..................................................................................................................6
Menu - how to work with ... ...................................................................................... 7
Input channels .........................................................................................................10
IN1 socket..........................................................................................................................10
IN2 socket..........................................................................................................................11
IN3 socket..........................................................................................................................11
IN4 socket..........................................................................................................................12
TRIG socket.......................................................................................................................12
Standard cable wiring ........................................................................................................12
Sensors properties ..................................................................................................13
AC sensors ........................................................................................................................13
DC sensors ........................................................................................................................14
Sensor Properties of recorded signal ................................................................................14
Global properties.....................................................................................................15
The About ... ............................................................................................................................... 15
Global/ Settings .......................................................................................................................... 15
Trigger Settings .......................................................................................................................... 16
Date/ Time .................................................................................................................................. 17
Factory Settings.......................................................................................................................... 17
Signal Source ............................................................................................................................. 17
The Launcher screen ..............................................................................................18
Update of the unit firmware................................................................................................18
Battery capacity .................................................................................................................18
Control and Menu buttons .................................................................................................19
The Shift button .................................................................................................................19
The Analyser mode .................................................................................................20
The Meas...........................................................................................................................20
The Graph..........................................................................................................................20
The Set ..............................................................................................................................20
Export of the Set to the Flash disc.....................................................................................20
First analyser screen .........................................................................................................21
New Set creation ...............................................................................................................21
New Meas creation ............................................................................................................23
New Basic................................................................................................................................... 23
New Advanced............................................................................................................................ 24
Next Set functions..............................................................................................................26
Making Measurement of the Set........................................................................................27
The Analyser buttons description ......................................................................................28
The Arrow Mode button .............................................................................................................. 28
The Stop, Esc button .................................................................................................................. 28
Graph Max/Min ........................................................................................................................... 28
Graph Properties ........................................................................................................................ 28
The Start, OK, Run button .......................................................................................................... 28
The Balancer ............................................................................................................29
The Project ........................................................................................................................29
The Project Screen ............................................................................................................29
2
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
The Advisor function ..........................................................................................................30
The first screen ..................................................................................................................31
Machine properties, planes number screen.......................................................................32
The measurement properties screen.................................................................................32
RUN 1 screen ....................................................................................................................33
RUN 2 screen ....................................................................................................................34
RUN 2 - Result screen.......................................................................................................35
The RUN 3 screen .............................................................................................................37
Trim Screens .....................................................................................................................37
Balancing Errors ................................................................................................................37
The RunUp ...............................................................................................................38
Measurement Control ........................................................................................................38
The Set and other items ....................................................................................................38
First measurement.............................................................................................................38
Buffering ............................................................................................................................39
The Graph properties.........................................................................................................39
aps_t ampl/phase/speed as function of time......................................................................... 40 ap_s ampl/phase as function of speed................................................................................. 40 ad_s ampl/difference vector as function of speed................................................................ 41 nyquist ........................................................................................................................................ 42 trend3D_t waterfall (cascade) diagram for spectra ............................................................. 43 cascade ...................................................................................................................................... 44
The Route .................................................................................................................45
Download of the route to the instrument............................................................................45
Route measurement ..........................................................................................................46
Reference values...............................................................................................................48
Manual entry ......................................................................................................................48
Export to Flash disc ...........................................................................................................49
Download of the route to the computer..............................................................................49
Recorder...................................................................................................................50
Record parameters ............................................................................................................50
Recording ..........................................................................................................................50
Edit of recorded data .........................................................................................................51
Appendix A: Technical Specification.....................................................................54
Appendix B: ACMT bearing and gearbox measurement......................................56
Applications .......................................................................................................................56
Description.........................................................................................................................56
ACMT is the solution..........................................................................................................56
Example.............................................................................................................................56
The ACMT method can do even more...............................................................................57
3
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
Before Switching On
Ignoring any recommendations mentioned below may cause failure of the device.
Operating with a power higher then 24 V can cause an accident.
Never connect higher then 30 V to the analyser !
Only suitable ICP powered sensors can be connected to the AC signal inputs.
If the measurement without ICP power is required, ICP power must be switched off. You can damage the external signal source, which is not protected agains ICP powering.
AC channels - voltage higher then
±
18 V (peak) can damage the instrument.
DC channels - voltage higher then
±
30 V (peak) can damage the instrument.
Always use only original cables designed for connection with sensor.
If you are unsure, contact your distributor or the manufacturer.
4
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd..
General information
Adash 4400 – VA4Pro
The switch-on
Use the POWER button for switch-on (older versions had the button in different position as in the picture).
The green LED on the front panel ( right at the top) should light after switch-on.
Connection to the computer
Use the USB cable, which is the standard accessory of VA4 set. The small plug connect to the USB socket ( see the image above). Connect second plug to the computer.
The instrument contains the standard Remove-able disc, with the "VA4Pro_disc" name. That is why the usual windows for e.g. flash disc connection appear on the computer. Close those windows.
When the operation failed, switch off the unit and try to connect it again.
The charging
The socket for external charger (instrument accessory) is under the POWER button. The BAT LED on the front panel ( right at the top) lights during charging.
5
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
The DSP board - monitoring and reset
The DSP board is the most important part of the instrument. The special chip provides all necessary operations, which are required for achieving of 4 channel synchronous data. You know, that every chip can freeze sometimes.
The STAT LED is on the top panel and enables to monitor the DSP board (older versions had the button in different position as in the picture). Several states can appear:
- Continuous green - OK, the measurement is running.
- Discontinuous green - OK, the measurement is not running.
- Red - the DSP board does not work properly.
When the red STAT occurs, do the reset of DSP board. Do not switch-off the instrument. Use the slim not sharp thing ( e.g. paper clip) and push the button, which is hidden in the RST hole.
Virtual analysers
When older analysers would take more measurements, they took them step by step. If the user wanted e.g. acceleration overall, velocity overall, velocity time signal and velocity spectrum from one sensor, then the analysers took first overall, then second overall with integration, then time signal and finally spectrum. The time which was required for all 4 measurements was the sum of 4 individual times.
The instrument includes high speed chips and use the much more advanced concept. For every individual measurement is created one virtual analyser in the instrument memory. All virtual analysers read data from input DSP board and perform required data acquisition.
What does it mean? It means, that the total required time is not equal the sum of all individual times, but it is equal the time required for the longest measurement.
6
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
Menu - how to work with ...
For the taking of measurements you have to define many parameters. All those definitions are providing by menu items. The procedure for operation with all menu items is the same. We describe it on example - the sensor properties definition.
The sensor properties first menu appears after you push the Sensors button.
Use the arrow buttons for one item selection, e.g. Ch2. Then push OK button. The second menu appears.
Again use the arrow button for one item selection. Then push the right arrow button to display possible parameters of selected item. E.g. for Sensitivity you see this picture:
Again use the arrow button for one sensitivity selection (1,10,100). In some cases also the user value is possible to enter. Select the user and push OK. The next window appears and the buttons get the numerical values entry functions.
7
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
Use the buttons and enter required value (e.g.45). If you need to edit the value, push the Shift button.
The buttons change the functions.
8
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
Now you can move the cursor, to use the Delete function. Press the Shift again and the buttons functions change back. When the value is correct, push OK. The menu with new value appears.
Use the arrows and select the OK item. Press the OK button and the working with sensors menu is closed.
As we mentioned the value entry, also the text has to be entered in some menu items. The screen looks similar to the numerical screen. The only difference is the characters selection on buttons. It works like mobile phones, for second character selection you must press the button two times. The
Shift button switches two modes of the buttons.
9
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
Input channels
All input sockets are in the top panel. The versions older then 0200 had only 3 sockets in the panel.
The input sockets labeled IN1, IN2, IN3, IN4 are used for AC or DC signals. The input socket labeled
TRIG is used for trigger signals, usually tacho. All sockets have several pins. It enables to connect more signals to one socket ( see wire diagrams).
The AC inputs enables to measure max voltage peak +/-12V. The DC channels enables to measure max +/- 24V.
IN1 socket
1 – CH1 AC INPUT
2 – GROUND
3 – +20V DC OUTPUT (max 10mA) (ver. 2.0 and higher)
4 – SHIELDING
5 – NOT USED
6 – CH1 DC INPUT
7 – NOT USED
10
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd..
IN2 socket
1 – CH2 AC INPUT
2 – GROUND
3 – CH1 AC INPUT
4 – SHIELDING
5 – CH3 AC INPUT
6 – CH2 DC INPUT
7 – CH4 AC INPUT
IN3 socket
1 – CH3 AC INPUT
2 – GROUND
3 – CH1 DC INPUT
4 – SHIELDING
5 – CH4 DC INPUT
6 – CH3 DC INPUT
7 – CH2 DC INPUT
Adash 4400 – VA4Pro
11
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd..
IN4 socket
(ver. 2.0 and higher).
1 – CH4 AC INPUT
2 – GROUND
3 – +20V DC OUTPUT (max 10mA)
4 – SHIELDING
5 – NOT USED
6 – CH4 DC INPUT
7 – NOT USED
TRIG socket
Adash 4400 – VA4Pro
1 – GROUND
2 – NOT USED
3 – NOT USED
4 – +5 V OUTPUT/ 50 mA for tacho power supplying
5 – TRIG INPUT - for tacho signal
Standard cable wiring
The standard cable, which are the part of the unit, have the sensor signal connected to the pin number
1. The second sensor wire is connected to the ground (pin 2).
When you use this cable:
In IN1 socket, the signal will be measured on CH1.
In IN2 socket, the signal will be measured on CH2.
In IN3 socket, the signal will be measured on CH3.
In IN4 socket, the signal will be measured on CH4 (ver. 2.0 and higher).
If you want to use the 3-direction sensor, then you should use the IN2 socket ( pins 3,1,5) + ground
(pin 2). You need the special cable for this purpose.
12
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
Sensors properties
When you connect the sensors to the instrument, you have to tell what kind of sensors you use. The
Sensors button is on most screens in the bottom.
Push the Sensors button. In the next menu select channel sensor you want define.
AC sensors
AC sensors are used for alternate current signals, e.g. vibrations.
After selection of Ch1 - Ch4 or All AC Channels item the sensor properties menu appears (e.g.Ch1).
ICP
on, off (selection of required setting accordingly the sensor type)
Type acc (acceleration), vel (velocity), disp (displacement), voltage, force
Sensitivity (mV/ selected unit) usually 1,10,100, user
Unit appropriate units are offered accordingly the Type of sensor
Angle the angle of sensor (see picture bellow). Usually used for proximity sensors.
13
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
Sensor angles examples.
DC sensors
DC sensors are used for discrete current signals, e.g. temperature, pressure, ... .
After selection of DC1 - DC4 or All DC Channels item the sensor properties menu appears (e.g.DC1).
value
Q (Offset) [mV] offset value
Unit
unit selected from the list
User Unit when the Unit-user, then any name of unit can be entered
Angle the angle of sensor (see picture above). Usually used for proximity sensors.
Sensor Properties of recorded signal
When you use the record (recorded signal from memory) for analysis, then the sensor properties are readable only. The message "Signal source isn't LIVE, Sensor readonly." appears. It is correct, because the sensor properties had to be defined before recording and properties are saved in the record. You cannot change the sensor for analysing - the properties are defined in the record.
14
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
Global properties
The parameters which have effect to all or many functions are understood as Global parameters. The definition is made by Global button.
The About ...
Global/ Settings
The underlined items are the default value (factory settings).
Display Route Values on,off When you want to go faster during the route and you do not want to look at measurement results after each point, then set it off.
Route Autosave on,off when set to on, the data are saved after taking measurement at each point by itself. When set to off, then the user after results confirmation has to save it manually ( Save button)
15
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
Display Small Values on, off When you are interested to see values under the 0,001, then set it to
on and the values will be displayed in exponential form ( e.g. 5,26E-6). Otherwise the 0 (zero) will be displayed.
ICP Initialisation Delay (s) default, user The delay (frequency response timeout) must be applied after the ICP switch-on, because we must wait for signal establishing.
Units metric, imperial.
Integrator HP Filter (Hz) 1,10 Hz
Displayed Spectra in Cascade
32, 128, 1024 the number of displayed spectra in cascade graph. It is not the number of measured spectra !
Date Format dd.mm.yy, yy.mm.dd
Language ENG, CZE, .... select your language
Trigger Settings
Trigger Mode single, retrig When you use the analogue oscilloscope, you see always the actual new signal on the screen. The retrig mode means the similar thing. The measurement is repeated until you push the Stop button. Select the single option when you want only one measurement.
RunUp Mode asap, manual, speed, time When we taking measurements during the runup, then has to be define how often should be data taken.
asap without any delay.
The next measurement is taken immediately after previous measurement
manual
The user starts next measurement manually.
speed The next measurement is taken when the speed is significantly different from the previous measurement speed. The user defines in Speed change(Hz) item, what it is significant change.
time All measurement are taken with the same time interval between them. The time interval length is define in Time Change(s).
Speed for value enter.
Trigger Source
freerun, external, manual, amplitude, tacho Every measurement must be triggered ( it means started). When you press the Start button for taking the measurement, you run only the preparation. When everything is ready to take the data, then the Trigger Source item is applied.
freerun waiting for anything.
The taking of measured data begin immediately after preparation without
16
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
external
The taking of measured data begins, when the external signal (voltage level higher then defined Tacho Trig Level) appears on the trigger input. Such signal may be generated e.g. when the machine starts to work. This type of signal is usually created in the control system.
manual The taking of measured data begin after pressing the Start button.
amplitude
The taking of measured data begin when the signal level exceed the Treshold
level, which is set by user also in this menu. Both - positive and negative levels are accepted.
tacho
The tacho is special case of external trigger. When we talk the tacho, we mean the signal (TTL) which contains one pulse during one rotation of the shaft. It can be also understood like series of single external pulses. The taking of measured data begins, when the external signal (voltage level higher then defined Tacho Trig Level) appears on the trigger input (the same like external item). But the tacho enables additional measurements ( the speed measurement) and settings ( e.g. signal overlap for spectrum averaging).
Tacho Trig Level (V) value
See the description of external and tacho in previous section.
Pretrig (%)
value in (-100,100) Usually the taking of measurement (e.g. time signal) begins exactly from the trigger moment. But in some applications you are interested also to know the signal before trigger. The required time should be define in seconds, but in signal analysers is usually defined as percent part of the total signal length. When 1 second time signal is measured and pretrigger=25, then 0,25s will be taken before trigger and 0,75s after trigger. Also the negative pretrigger could be used. It means that the time signal will be taken later then trigger pulse.
Ampl Trig Level (unit) value See the description of amplitude mode (Trigger
Source section). The unit is the implication of the unit of sensor.
Ampl Trig Channel ( 1,2,3,4)
The number of channel, which will be used for amplitude trigger.
Date/ Time
Set the actual date and time.
Factory Settings
This function enables to return to default factory setting of all parameters.
Signal Source
Every measurement can be taken from LIVE channels ( AC 1-4 or DC 1-4 ) or from RECORD ( see
Recorder chapter for understanding). All records saved in the memory are displayed for selection.
Select required item and press OK button. The selected signal source is also displayed in the Global window.
17
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
The Launcher screen
After switch-on the LAUNCHER screen appears. You can select the required mode of the unit.
Update of the unit firmware
You can download the updated firmware from producer website www.adash.cz. Follow the procedure:
- Download the file for update ( e.g. A4400_ver0114.u44) from website (www.adash.cz) and save it to your computer.
- Connect the instrument to the computer. Remember, the it has to be switched off.
- Run the Explorer or other software, which you use for copy of files.
- Copy the update file from the computer to the VA4_DISC.
- Use Safely remove hardware function and disconnect instrument from the computer.
- Switch-on the instrument to the Launcher screen.
- Push the Update button.
- Select the required update file from the list ( more then only one version can be saved in the instrument). Press OK.
- The Launcher window is closed now. The procedure of update is described in the new command window.
- After the update the Launcher screen appears again.
Battery capacity
The information about % of battery lifetime is displayed in the right bottom corner of the display.
When the capacity is less the 3%, then lifetime image begin to blink. At that time the running measurements are stopped. The next measurement is not enabled.
18
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
Control and Menu buttons
Control buttons with the description are on the left and right screen side. The Menu items with the description are displayed in the bottom of the screen.
The Shift button
The Shift button changes the purposes of buttons. It is used for numerical and text inputs.
19
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
The Analyser mode
The Analyser mode is the basic mode for signal analysis. If you have not prepared the Route measurement, then you use for analysis the Analyser mode. All required parameters must be set by hand or you can use the older measurement parameters, which you developed in the past and saved to the unit memory.
The Meas
The Meas means one measurement as it is usually understood, e.g. overall value or time signal or spectrum or other.
The Graph
The Measurement is saved in the memory as array of more or less numerical values. The graphical form of that values displayed on the screen we will call the Graph. One Graph works with data from one measurement. Also the displaying of one overall value is also the Graph.
The Set
The Set is the most important term in the Analyser mode. The Set is the set ( or group) of one or more
Measurements, which the user wants to take together. The Analyser performs measurement of Sets.
E.g. you want to take 4 Measurements together - acceleration overall, velocity overall, velocity time signal and velocity spectrum. You prepare the Set, which includes these 4 required Measurements.
The definition of Set is saved in the analyser memory. You can save many various Sets, which can contain your often used sets of measurement. Then you select one Set and run it. The taking off all measurements included in the set is made. See also Virtual analysers section for better understanding.
Export of the Set to the Flash disc
The computer can read any data from VA4 flash disc only. The set with measured data has to be exported to the flash before the transfer to the PC. During the set measurement are data saved to the
VA4 hard disc only. When the set is closed, then the VA4 asks the user "Export to flash?" and user selects one option. The export to flash is not done automatically because the writing procedure to flash is slow. That is why the user can determine, when is the right moment to export the set.
In the menu item Set/ Export you can select the set and export it manually.
20
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
First analyser screen
The first Analyser screen contains the list of Sets saved in the memory or the empty list, when no Sets were saved.
New Set creation
Push the Set button. Them menu appears, select New item. Enter the name and push OK button.
21
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
Enter the name of new set. Use the Shift button for next buttons displaying. Then press OK. The clear screen appears. Note you need to create the first Meas.
22
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd..
New Meas creation
Press the Meas button and select New Basic or New Advanced.
Adash 4400 – VA4Pro
New Basic
You can create the new Meas by two ways. When you want define some basic measurement use the
New Basic. Select required measurement from the list. This way is very fast.
23
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
New Advanced
The base menu for definition of measurements appears. The content of the menu is implication of the measurement Type selection. See next table. The black area means, that the item from left column is used for the type of measurement (top row).
Type
Detect Type
Response
Channel
Band Fmin (Hz)
Band Fmax(Hz)
Input channel
Output channel
FFT Window
Range
ACMT FS(Hz)
Samples
Lines
Max Speed
Orders
Avg
Overlap
Unit wide band g-env wide band time signal orbit spec g-env speed ACMT orda spec (Orders) aps
(Ampl/
Phase) fresp
(Freq
Resp.) dc center line
24
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd..
Detect Type
RMS, P-P, 0-P
Adash 4400 – VA4Pro
The detected value property ( P means Peak).
Response H1, H2, H3 Standard frequency response functions, H1- input noise, H2 - output noise, H3 - the average of H1 and H2.
Channel 1, .., 4 The input signal source channel for evaluation.
Band Fmin (Hz)
value The low cut-off frequency of band pass filter, which is applied to the signal before evaluation. The none value means, that only input DSP filter is applied ( approx.
0,6 Hz).
Band Fmax(Hz)
value The high cut-off frequency of band pass filter, which is applied to the signal before evaluation. Under this item is also displayed the information about sampling frequency (fs=), which be applied for evaluation.
Input channel
1, .., 4 Only for response functions, where is needed to define it.
Output channel
1, .., 4 Only for response functions, where is needed to define it.
FFT Window
FFT windows functions.
Rectangular, Hanning, Transient, Exponential The standard offer of
Range
value Frequency range of the graph. Under this item is also displayed the information about sampling frequency (fs=), which be applied for evaluation.
The sampling frequency for ACMT evaluation. See the ACMT
ACMT FS(Hz)
value chapter for understanding.
Samples value Number of samples. The correspondent signal time length is displayed under this item.
Lines value
displayed under this item.
Number of lines. The correspondent signal time length is
Max Speed
Low ( <600 RPM), Standard ( <3600 RPM), High ( <7200 RPM), User
This information is used for Ampl/ Phase and Order Analysis for optimal sampling frequency choice. To define the near higher frequency then expected speed maximum is the best choice. When the High value is entered, then the analyser is not able to make evaluation for speed much lower then the expected speed maximum ! Also the time consumption for calculation is higher because the high lines number must be used and long time signal taken.
Orders
(1/2,1-5), (1-5), (1/2,1-10), (1-10)
Avg
value
Unit name
This information is used for decision whether and how many integrations should be used.
25
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd..
Next Set functions
Adash 4400 – VA4Pro
When the list of Sets (which are saved in the memory) is not displayed (e.g. the graphs are on the screen) then use the Set List item.
The selected Set in list or opened Set ( looking to the graphs) you can Copy to new Set ( when you want to keep the old Set and use the recently arranged new Set.
You can also Rename or Delete it.
When you already take some measurements, then the data is saved in the Set. The Clear Data function erases them and leaves the Set empty like new set.
The measurement results are not saved automatically. Use Save Data item for that. When you save data e.g. each hour, then you can read them from the memory and display their trend. Use View
Trend function for it.
26
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
Making Measurement of the Set
As has been described already the Set contains definitions of measurements (Meas), which we want to take together.
To show the example is the best way how to learn the process of measurement.
The requirement for the Set:
1. RMS wideband value in mm/s, frequency band 10-1600Hz, from channel 1
2. RMS wideband value in g, frequency band 500-25600Hz, from channel 1
3. Spectrum in mm/s, range 400Hz, 800 lines, from channel 1, number of average 16, overlap 50%
4. Spectrum in g, range 3200Hz, 3200 lines, from channel 1, number of average 32, overlap 50%
When the measurements definition is made ( see the New Meas creation section) everything is ready to make the real measurement. Push the Start button (green triangle button). For stopping the measurement use Stop button (the red square button). If the Trigger Mode is set to single, then only one measurement is taken.
Every graph contains result of one measurement. If more measurement are defined in the Set, then more screens with graphs are developed.
The description of each graph is in the top.
Example:
The translation: Meas No.1, RMS value, Channel 1, Applied band filter 10-1600Hz, Number of
Samples of the signal 4096, Time length of signal 1s. The Signal means the time signal, from which the evaluation was made.
The translation: Meas No.4, Spectrum from Channel 1, Applied band filter 10-800Hz, Lines 800 Time length of signal 1s, 16/16 - 16 measurement from total 16 just made
27
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
The X range (1,800)Hz, Linear X scale, The Y range (0,0,5) mm/s, Linear Y scale, The Y scale mode max ( see Graph Properties section), The cursor position 8Hz, cursor value 0,3888mm/s
The Analyser buttons description
The Arrow Mode button
The arrow buttons can work in several modes. The Arrow Mode button shifts their functions.
Functions for up and down arrows:
Select - moves the selection of active graph
Zoom - makes zoom-in or zoom-out on vertical Y axe
Move - when the zoom-in is applied, then button move with the signal in defined zoom view vertically
Position - you can change the order of graphs
Functions for left and right arrows:
Cursor - moves the cursor
Zoom mode - makes zoom-in or zoom-out functions on horizontal X axe
Move mode - when the zoom-in is applied, then button move with the signal in defined zoom view horizontally
Trend - displays the trend of all values saved in the memory (the history)
Repeat the pressing of Arrow mode button to circular change of function.
The Stop, Esc button
This button stops the measurement or escapes from menu lists.
Graph Max/Min
Maximises the active graph to the whole screen or returns back to the initial screen with more graphs.
Graph Properties
The list of properties is displayed and can be edited. The scale ranges and types (lin, log,...) definitions are the typical use.
The Start, OK, Run button
This button runs the measurement or confirms entries.
28
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd..
The Balancer
Adash 4400 – VA4Pro
The Project
The Project is the base structure in balancer. It corresponds of one balancing job. You can use the same Project for repeated jobs on the same machine. The measured data will be re-written.
The Project contains all measured or entered data, which were be used during the job. The typical scheme looks like next list of steps:
- Project name enter.
- Mode (machine type and number of planes) enter.
- RUN 1 - Initial measurement of vibration amplitude and phase in required number of planes.
- Trial mass put on the rotor. Step by step to all planes.
- RUN 2 - Trial mass response measurement. Step by step to all planes.
- Final masses put on all planes.
- RUN 3 - Check of effect (success) measurement.
- Trim measurements for additional masses and better results.
The Project Screen
Every step is represented by one screen. The movement between screens is provided by up/down arrows. The usual Enter button is not used, it could confuse the user. The movement enables to return back anytime. The important property must be clearly told. When you return back in the job screens and you take again repeated measurement or value enter, then the measured data will be erased in all screens after actual screen. The reason is simple. The implications are derived from every screen to the next screens. When you repeat the measurement, you change the parameters for those implications. That is why all next screen implications must be removed and you have to make all necessary measurements again.
29
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
The Advisor function
This function helps you with decision whether to balance or to not balance and make different maintenance job. This function works automatically.
Press the button Advisor. Define the input channel. When you make two channel job, then use the channel with higher vibration level. Then the main Advisor screen appears.
The speed value and APS values are displayed. The advisor function has next results:
Balancing not recommended.
When the balancing is not recommended, then also the reason is displayed:
Balancing possible but very small vibration level on speed frequency.
More vibration sources found in the system.
The looseness is found.
Low amplitude on speed frequency. The total vibration value is caused by different reason.
The speed is not stable.
The amplitude is not stable.
The phase is not stable.
30
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
The first screen
The list of saved projects or the Empty label is displayed on the first screen. Select one project or use the Project Button for New project creation.
Also next functions for projects managing are enabled.
When you select the New item, the you will entry the name of new project. The screen for manual entry was in details described in Menu - how to work with ... section.
31
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
Machine properties, planes number screen
The machine properties and number of planes are the initial information of each Project. When the
Project name is entered the next screen with properties selection appears.
The name on the first line is followed by description of selected mode (red bordered). Use the arrows to select required mode. Use down arrow to go to the next measurement properties screen.
The measurement properties screen
Channels - select the numbers of channel used for the job.
Look - select the look of the machine accordingly your place in the field. It should help you to measure always the right things on the right points You understand this item totally, when you have tried to click to both options. The none choice means any images will be used on the screens. The Look parameter has no effect in job calculations.
Direction - means the rotation direction on the selected image. The Direction parameter has no effect in job calculations.
Plane1, Plane2 channels - selection of channels, which will be used for measurement data collection.
The same channel has to be used for single mode.
32
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
Blades - the number of blades ( for rotors with blades). This parameter is used in job calculations to split the mass to blades.
Use the Tab button for selection of item to entry. Use left or right arrow for the selection of correct option.
Press down arrow to go to the next RUN 1 screen.
RUN 1 screen
The screen is divided to two parts. The left part corresponds to plane 1 and right to plane 2. Only one part is active. The non-active part has un-sharpened image. As described at the top, place the sensor to the Plane 1 point and start the measurement. Corresponding bearing house is red coloured. The results appear in the bottom. Use the right arrow button to move the active focus. Make the same for the Plane 2.
You can also use the Edit button, when you want to enter the values manually. Use the Tab for shift between values.
Then the screen should look like next picture.
33
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
RUN 2 screen
The trial mass mounting and response measurement is required to take on RUN 2 screen.
Use the Properties button and enter the trial mass for corresponding plane.
The corresponding plane for trial mass mounting is demonstrated by the red disc. After the measurement of plane 1 take the measurement on plane 2 (or take them at once, when you use 2 channels). The trial mass remain in the plane 1.
After measurements of both planes with trial mass on the plane 1 remove the trial mass from plane 1.
Press down arrow. The same two measurements we have to take with trial mass on plane 2. The screen for those measurement looks similarly like previous screen. Only the red disc is in the plane 2.
Press down arrow button after both measurements.
The RUN 2 completed screen is in the next picture.
34
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
RUN 2 - Result screen
35
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
Remove the trial mass and mount the final masses to both planes. The angle is applied from trial mass position, which represents the 0 (zero) degrees.
In case you have used blades, the result screen may look like that.
The result with trial mass kept is also available for one plane jobs.
36
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
The RUN 3 screen
When the masses are mounted you want to check the job. The measurement on both planes are required. The screen is in fact the same as screen for RUN 1.
Trim Screens
After RUN3 measurement you can continue with the job when you are not satisfied with the results.
These next steps do not required trial mass measurements already. After each measurement the next masses are recommended. The trim screens are very similar to screens described beyond.
Balancing Errors
Balancing errors can occur during the job. Several types exist. When any error occurs the message window is displayed.
The window contains the table with the error list. Each error contains the Plane number and error description. Follow the description and fix it.
37
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd..
The RunUp
Adash 4400 – VA4Pro
Measurement Control
When you need to measure Run Up or Coast Down of the machines, then you should use the RunUp mode. It enables the same measurements as in Analyser mode, but controlled by speed or time. What does it mean "controlled"? In Analyser mode you can measure the Set and then you have to save measurements manually.
The RunUp is different. The measurements are saved automatically and additionally the measurement are regularly repeated under the control. The tigger function is used for that control. The menu item
Global/ Trigger Settings/ RunUp mode is used for setting.
Usually the speed is used for that control and new measurement is made, when the speed changes from previous measurement of defined value (e.g.10 RPM).
Also the time can be use to control that procedure. Then you can take the measurement in defined time interval ( e.g. each 60 sec ).
The ASAP is the next choice. It means no delay between measurements - As Soon As Possible. Be very careful for such mode. When you want to measure e.g. aps only, then the maximum measurement number can be reached very soon ( 1 minute). The runup measurement will be stopped then.
The last choice is the Manual mode. You can press the Start button at any suitable moment to make a new measurement.
The Set and other items
The meaning of the Set and also of other items in the RunUp menu are the same as in the Analyser mode.
First measurement
We define one measurement. The proximity sensor is in channel 1.
We use the record PR-01 - see Signal Source item in Global. Start measurement - push Start button. When the measurement is completed, the End of Record message appears. Press OK.
The last measured aps value is on the screen. Press Set/ View Trend and in the left upper screen corner the list of measurements appears. The name of every measurement is developed from its date and time.
Select last trend from the list and press OK.
38
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
The aps - amplitude+phase+speed graph appears.
Use Arrow Mode button for functions selection.
Buffering
Measured signal is collected into the input memory. The analyse procedures read the signal data from the memory and compute all required results, which are displayed on the screen. In the case, when too many results are required, the computation is slow and displayed graphs are not actual - they are delayed. We are talking about Real Time (RT) graphs ( you see the actual results) or about Non Real
Time (non RT) graphs (delayed results). After the measurement is stopped (e.g. by Stop button), the computation continues until the input memory is empty. The bellow window appears.
You can wait for all data acquisition or if you are not interested of measurement from input memory press the Stop button to stop data processing.
The Graph properties
Several types of graphs is available under the View item.
For aps are available next items :
39
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd..
For spectrum are available next items :
See the previous graph.
ap_s ampl/phase as function of speed
Adash 4400 – VA4Pro
40
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd..
ad_s ampl/difference vector as function of speed
Adash 4400 – VA4Pro
The graph on the bottom displays the vector diference of each aps measurement in relation to aps on cursor position.
41
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd..
nyquist
Adash 4400 – VA4Pro
42
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
43
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd..
cascade
Adash 4400 – VA4Pro
44
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd..
The Route
Adash 4400 – VA4Pro
Download of the route to the instrument
The co-operation with DDS software is required for the route measurement. See also the DDS user manual for more details. We do not described all details about DDS function in this guide.
Open in DDS the database, from which you want the route create. Use Connect Instrument function and the route window appears.
Connect the unit with the computer. See Connection to the computer chapter.
Press the Connect button, the message window with connection process description should appear.
Move required points from DDS tree to the route window.
Press the Save to A4400 button. In the next window select the route in the instrument memory and rewrite it or define new name. Press OK. The route data will be loaded from computer to the instrument.
45
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
Route measurement
Select the Route mode in Launcher screen. The list of routes in the memory is displayed.
Select one route and press OK. The list of machines appears.
Select the machine and press right arrow to develop the list of measurement points.
In this moment you can start the measurement or by right arrow display the list of measurements, which are defined for this point. By left arrow button you will close the displayed list and you return back to the previous list.
46
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
When you press the Start button in the points list, the measurement graphs are drawn with the
No_Data message. If the required sensor (defined in the route) is not compatible with the sensor connected to channel input (Sensors properties) then next message window appears.
Change the sensor or use the different sensitivity and press Continue.
The complete point measurement should be taken now. The measured data are or are not displayed on the screen regarding the Display Route Values parameter in Global Settings.
Use the Esc to return back to points list. The measured points are labelled by the symbol.
Point button enables to work with the measurement point data.
Copy - Creates the new point with the same setup. It is usable, when you need create new out of route point on the machine.
Export - Makes copy of route from hard disc to DDS memory. Then the route is accessible from DDS software.
47
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd..
Rename - renames the actual item
Delete - deletes the actual item
Adash 4400 – VA4Pro
Clear Data - Erases all measured data in selected point.
Clear Checks - When the point data is measured, the check inform about that. When you want to measure the route again, it is better to erase checks and begin with empty list.
Save Data - When autosave is off, then you have to use this item for saving.
View Trend - The instrument enables repeat the measurement in the route. It means, that also inside the route the trend exist. Use this item to view that.
View Actual - the just measured data are displayed
Route list - Display the list of all routes in the instrument.
Reference values
You can download reference values from DDS to VA4 unit for spectrum and wideband measurements.
These values are displayed together (red coloured) with measured values. Spectrum’s reference signal blinks over measured signal. Wideband’s reference value is displayed in left side of graph signed by “R:” or like a line in trend.
Manual entry
The route may contain the measurements, which have to be entered manually ( e.g. pressures read from analogue display). The measurement with subtype MANUAL in DDS is defined. Before beginning of measurements from sensors (after you press START button) the window for manual input appears (one for each manual input).
48
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
Export to Flash disc
The computer can read any data from VA4 flash disc only. The route with measured data has to be exported to the flash before the transfer. During the route measurement are data saved to the VA4 hard disc only. When the route is closed the VA4 asks the user "Export to flash?" and user selects one option. The export to flash is not done automatically because the writing procedure to flash is slow.
The large route export can take several minutes. That is why the user can determine, when is the right moment to export the route.
In the menu item Route/ Export you can select the route and export it manually.
Download of the route to the computer
The process is the same as the load of route to the instrument. In Connect instrument window use the Read from the A4400 button. Select the required route from the list ( all routes saved in the instrument) and read it. The list of all points appears in instrument window. The grey items are not measured.
49
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
Recorder
Many of older engineers remember the past time, when the signal was recorded to the tape-recorder and consequently analysed in analyser. Such approach had one important benefit. You can analyse the signal again and again. When you need to make all required analysis in real-time, you are under time pressure. If additionally the e.g. runup can be run only once, the pressure is extreme. The taperecorder was the solution. It was simple unit with simple operation, no danger to loose the data.
The similar solution offers the VA4 Recorder. It enables to record simultaneously all 4 AC channels, tacho channel and 4 DC process values channels into the unit memory. The sampling frequency is
65kHz. The maximum record length depends of free memory size. The 3GB/ 1hour is required.
Record parameters
Run the Recorder. The list of records which are in the memory appears on the screen. Select one of them ( arrows and OK). When you want to display the list of projects in other moments, use Project button and Project List item.
Selected project you can:
- Measure again by pressing Start. Old data will be erased.
- Use Project button and Copy it to the new project. The used parameters will be kept.
- Use Project button and Delete or Rename it.
For new project creation use Project button and New item. Then press the Record button and the menu appears.
Ch1, .. Ch4 on, off The channel will or will not be recorded.
Trigger channel
on, off The trigger channel will or will not be recorded.
Time (minutes) value or manual stopped recording can be also stopped manually.
The recorded time length. The
Start of Rec
freerun
external
freerun, external, amplitude
After the measurement preparation is the recording started immediately.
The external signal (voltage level higher then defined threshold level in the
Global menu) starts the recording. Such signal may be generated e.g. when the machine starts to work. This type of signal is usually created in the control system.
amplitude
The recording is started when the signal level exceed the Treshold level, which is set by user in Global menu. Both - positive and negative levels are accepted.
Recording
When the Record parameters is set, use the Start button for start of the recording. During the recording the actual data are displayed on the screen.
50
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
The process is finished when
- the time is over,
- manually by Stop button,
- the memory is full.
Edit of recorded data
The project (record) usually contains more data then we need. You can cut-off the parts, which are unnecessary. The procedure is very simple. Open the project. All measured data are displayed.
51
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
Now you should define the Zoom and then to save that Zoom. The Zoom is defined by two values:
Cursor position and Length. Use the Arrow Mode button and change the function of buttons in the right side.
Cursor the arrows move with the cursor ( with the start position of Zoom), the initial position of the Cursor is on the left
Length the arrows move with the length of Zoom ( with the end position of Zoom), the initial position of the Length is on the right
Zoom only the zoomed area will be displayed
Move the arrows move with defined Zoom, when the Zoom is applied
Save Zoom As
saves the Zoom as new project
Definition of cursor and length position.
52
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
Zoomed view.
53
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd..
Appendix A: Technical Specification
Input Channels:
AC inputs filter:
- 4 AC ( ICP powering available),
- 4 DC (process values),
- 1 external trigger (tacho)
- analog HPF 0.33Hz and digital HPF 0.68Hz
Sensor Excitation Current: on (typ. 3.8mA), off ( 0 mA)
Modes: - Data-Collector (route measurements)
- Balancer
- RunUp
Adash 4400 – VA4Pro
Processor:
Memory:
Input Ranges :
A/D Resolution:
- 1,6 GHz
- 120 GB
- AC +/-12 V peak ( 1200g PEAK for acc 10mV/g)
- 24 bit input, 64 bit double floating point internal precision
No Autogain procedures required!
Sampling Frequency: - max 64 kHz for synchronous measurement on 4 channels
- max 196 kHz for single channel measurement
Sampling: - 4 synchronous AC channels
Time Signal Length (s):- 1024s maximum
FFT Ranges (Hz): - 25, 50, 100, 200, 400, 800, 1600, 3200, 6400, 12800, 25600, 76800 (1ch)
FFT Lines:
FFT processor:
- max 25 600 lines
- extremely high speed FFT ( 25 600 lines spectrum calculation takes 25 ms)
Signal Acquisition: - max 2 integrations (displacement is available from accelerometer)
Averaging - 1- 255
Overlaping (%): - 0, 25, 50, 75
Meas. windows: - Hanning, rectangular, transient, exponential
Tacho speed range: - 30 – 300000 RPM
Tacho/Trig. pulses: - TTL signal or pulses >0.7V
Triggering: - manual (button)
- external (tacho, TTL)
- time interval ( e.g. 1 measurement each 1 minute)
- speed change ( runup control).
Recording
- sampling frequency 64 kHz
- record length 3 GB / 1 hour ( 4ch AC , 4ch DC , 1ch tacho signal)
( 120GB memory enables 40 hours of recording)
Data Acquisition: - overall values (TRUE RMS, TRUE PEAK, TRUE PEAK-PEAK)
- frequency band measurement (adjustable by user)
- ACMT procedure for low speed machines bearings
- time signal – max. 65 536 samples
- realtime FFT – max. 25 600 lines
- measurement
- process DC values
Data display: - overall values
- spectrum
- frequency response functions
54
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd..
- 3D graphs ( waterfall, cascade)
Vitrual Analysers: - simultaneous real time data acquisition
Display: - colour 7.5” LCD, 800x600 resolution
Adash 4400 – VA4Pro
Temperature Range: - -10 °C - +50 °C, 15°F-120°F
Powering: - Li-Ion long life battery pack (more then 5 hours of measurement)
Dimensions:
Weight:
- 250 x 190 x 50 mm
- 2200 g
55
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
Appendix B: ACMT bearing and gearbox measurement
Applications
The ACMT is the brilliant tool for condition of low-speed machines like paper machines, rolling mills, transport mechanisms… .
Description
Various processes produces short duration pulses are in slow speed machinery. Pulses are often caused by rolling element bearings, gearbox wear, etc. It is important to be able to accurately detect and analyse these pulses for correct diagnosis.
The individual pulse can have very short duration. Consequently it is necessary to set a high sampling frequency for measurement. Only in this way ensures to obtain a correct measurement of signal amplitude.
The time interval between pulses can be very long when the speed is low ( seconds, minutes). We need to see the time signal which contains several pulses as minimum for correct evaluation. The long length of time signal is required. This matter needs to use the low sampling frequency.
These two aspects produce the conflict in the measurement setting:
1. We need to use high frequency sampling for pulse measurement, which means the measured signal will very short e.g. 100ms. When the time interval between pulses is in seconds we have low chance to catch it. And we have no chance to have more pulses in one time signal.
2. We need the low sampling frequency for long time record e.g. 10s to obtain more pulses in one signal. But with such sampling we cannot measure the pulse, because cut out by anti-aliasing filter. If we switch off this filter, we have also no chance to catch it, because pulse duration is short and time period between samples is long.
ACMT is the solution
This method implements both contradictory requests by double sampling the data. The high sampling frequency is used in the beginning. Then the data are compressed. That is why we can take long time signal for evaluation.
Example
All measurements were taken on a slow-speed 23132-TOR rolling bearing rotating at 60 rpm (1 Hz).
Outer race defect is on the bearing. The short pulses are generated during the operation.
We measure the signal with a record length of 4sec. When 2048 samples (standard value) is used, then 200Hz anti aliasing filter is used. We take the signal without any pulses. All of them are cut off by filter.
56
For further technical and contact information visit www.adash.eu, email: [email protected]
ADASH Ltd.. Adash 4400 – VA4Pro
We use the 19200Hz sampling frequency. But we can measure only 42ms time signal. The time between the pulses is 114 ms. We need to be lucky and to hit the pulse.
Next measurement uses the ACMT method. You see, it works. Long time signal contains required number of pulses and the peak of each of them is captured. That is what we need.
The ACMT method can do even more
Short duration pulses have usually small amplitude. They are often modulated by speed frequency.
We use standard measurement and result is in the next picture.
You se only speed sine wave and no pulses, which are filtered by anti aliasing.
The standard ACMT is used in next picture.
The short-pulses are detected but their amplitude is modulated. We can use the ACMT together with band pass filtering and remove the sine wave from the signal.
This result is much better, because Y axe scale corresponds with pulses amplitude, not with speed sine wave amplitude.
57
For further technical and contact information visit www.adash.eu, email: [email protected]
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement
Key features
4 channel synchronous data acquisition
Analyser, RunUp, Balancer, Recorder modes
Built-in recorder
Route measurement functionality
ACMT bearing and gearbox measurement
Frequently asked questions
The VA4Pro 4400 offers four modes: Analyser, RunUp, Balancer, and Recorder. Analyser mode is for standard signal analysis, RunUp mode is for measurements during machine start-up, Balancer mode is for balancing rotating machinery, and Recorder mode allows you to capture and analyze vibration data over time.
You can download the latest firmware from the Adash website. After downloading the update file, connect the instrument to your computer, copy the file to the VA4_DISC, and then follow the on-screen instructions to complete the update.
The VA4Pro 4400 supports both AC and DC sensors. For AC signals, such as vibrations, you can use ICP powered sensors. For DC signals, such as temperature or pressure, you can use appropriate DC sensors.
