3StarsNet ATA User Manual

3StarsNet ATA User Manual
3STARSNET ATA User Manual
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
1 / 42
3StarsNet ATA User Manual
1
3STARSNET ATA Features............................................................................. 4
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2
Web Configuration ........................................................................................... 7
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3
4
Access Web setting page..........................................................................................7
Current state................................................................................................................9
Network ......................................................................................................................10
2.3.1
Wan Config ................................................. 10
2.3.2
LAN Config ................................................. 11
VoIP ............................................................................................................................11
2.4.1 SIP Config ..................................................... 11
2.4.2 Iax2 Config .................................................... 13
Advance .....................................................................................................................14
2.5.1
DHCP Server................................................ 14
2.5.2
NAT ........................................................ 15
2.5.3
Net Service ................................................. 16
2.5.4
QoS settings ................................................ 17
2.5.5
Advance SIP settings ......................................... 18
2.5.6
Digital Map .................................................. 19
2.5.7
Call Service Settings ......................................... 20
2.5.8 MMI Filter.................................................. 21
2.5.9
Audio Settings ............................................... 22
2.5.10 VPN......................................................... 22
Dial-Peer Settings .......................................................................................................24
Config Manage..........................................................................................................25
Update........................................................................................................................26
System Manage........................................................................................................28
2.9.1
Account Manage ............................................. 28
2.9.2
Syslog Config: ............................................... 28
2.9.3
Time Set: ................................................... 29
2.9.4
Logout&Reboot .............................................. 29
IVR setting ...................................................................................................... 30
Telnet Console ............................................................................................... 31
4.1
4.2
5
Appearance .................................................................................................................4
Interface .......................................................................................................................4
Electricity characteristic .............................................................................................5
Software.......................................................................................................................5
Standard and Protocols .............................................................................................5
Compliant Standards..................................................................................................6
Operating requirement...............................................................................................6
Package .......................................................................................................................6
Installation....................................................................................................................7
Introduce....................................................................................................................31
Global Command......................................................................................................32
Tree Structure................................................................................................. 33
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
2 / 42
3StarsNet ATA User Manual
6
7
8
9
Network Diagnosis......................................................................................... 34
Restore to factory default .............................................................................. 34
POST Mode(safe mode) ............................................................................... 35
FAQ ................................................................................................................. 36
How many SIP servers may 3STARSNET ATA register simultaneously? .....
How can I know the 3STARSNET ATA’s IP address? ......................
How to use 3STARSNET ATA’s Lifeline function? .........................
Why the settings vanish after reboot? ...................................
How to use the dial rule? ..............................................
How to use speed dial function? .......................................
How to configure digital map? .........................................
How to use Call Forward, Call Transfer and 3-way Conference calls? .......
VLAN implement.....................................................
36
36
36
36
36
38
38
38
39
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
3 / 42
3StarsNet ATA User Manual
1 3STARSNET ATA Features
1.1
Appearance
： power connection status
PWR
SYS :
WAN:
LAN:
PSTN:
VoIP:
call out
server registration status . registered: on , gliting , not-registered , off
WAN port connectiong , contected , on , offline : off
LAN port connectiong , contected , on , offline : off
light on when PSTN call come in/out
light on when VoIP call come in/out , The default status when pick up the call is VoIP
1.2
Interface
Power:
Port:
WAN:
LAN:
Output Power:12VDC,500mA.
RJ11 port. Connect to handset or the Lifeline accessory.
RJ45 port.
RJ45 port.
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
4 / 42
3StarsNet ATA User Manual
1.3
1.4
Electricity characteristic
Speciality of electric: output the 12V 500mA DC
The network connects:2 RJ45 connect, a WAN, a LAN
FXS: 2 port
Software
Support two sip servers running at the same time.
Back-up sip server support.
NAT, Firewall.
DHCP client and server.
Support PPPoE, (used for ADSL, cable modem connecting).
Support major G7.xxx CODEC.
VAD,CNG.
G.165 compliant 16ms echo cancellation
Tone generation and Local DTMF re-generation according with ITU-T
E.164 dial plan and customized dial rules
Support Lifeline.
Hotline.
Speed Dial
Call Forward, Call Transfer, 3-way conference calls
Caller ID display
DND(Do Not Disturb),Black List,Limit List
Upgrade firmware through FTP or HTTP.
Web management.
Reverse polarity
Telnet remote management.
Voice prompt
adjustable user password and super password
1.5
Standard and Protocols
IEEE 802.3 /802.3 u 10 Base T / 100Base TX
PPPoE: PPP Protocol over Ethernet
DHCP Client and Server: Dynamic Host Configuration Protocol
G.711 u/a; G729 audio Codec
SIP RFC3261, RFC 2543
IAX2
TCP/IP: Internet transfer and control protocol
RTP: Real-time Transport Protocol
RTCP: Real-time Control Protocol
VAD/CNG save bandwidth
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
5 / 42
3StarsNet ATA User Manual
1.6
Telnet: Internet's remote login protocol
DNS: Domain Name Server
TFTP: Trivial File Transfer Protocol
HTTP: Hyper Text Transfer protocol
FTP: File Transfer protocol
RFC 3362：T.38 protocol
Compliant Standards
CE：EN55024,EN55022
FCC part15
comply with ROHS in EU
comply with ROHS in China
Explanation:
The letter “e” is the first letter of “environment: and “electronic”, The rim is a round with two
arrow , stands for recycle. The number 20 stands for the years of environment protection.
Please note the years of environment protection is not discarding year nor usage life
1.7
Operating requirement
●
●
●
1.8
Operation temperature: 0 to 40° C (32° to 104° F)
Storage temperature: -30° to 65° C (-22° to 149° F)
Humidity: 10 to 90% no dew
Package
Size
128 x 85 x 30 mm
Packing List
3STARSNET ATA gateway
Power adaptor (12v, 500mA)
Manual CD
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
6 / 42
3StarsNet ATA User Manual
1.9
Installation
Use Ethernet cable to connect 3STARSNET ATA’s LAN port and your computer. Set
your computer’s ip to the network 192.168.10.x or using dynamic obtain IP. Open your
web browser and key in 192.168.10.1. Then you will see the logon page of 3STARSNET
ATA, the default username and password is admin/admin for administrator and
guest/guest for guest.
Set up page for VoIP use only:
Internet
PBX
Power
PSTN
User
POS Phone
2 Web Configuration
2.1 Access Web setting page
Enter 3STARSNET ATA IP address in the web browser and press ENTER to go to the log
on page, and key in the username and password to access 3STARSNET ATA setting
page.
Default username and password is:
Administrator:
Username: admin
password: admin
User:
Username: guest
Username: guest
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
7 / 42
3StarsNet ATA User Manual
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
8 / 42
3StarsNet ATA User Manual
2.2 Current state
This page shows 3STARSNET ATA’s running state.
Network
：shows the WAN and LAN port connecting state and current settings.
：
VoIP show the default protocol, the working state of SIP and IAX2, you can see whether
3STARSNET ATA has registered the public sip server and IAX2 server.
Phone Number shows the public sip server、 the private sip server and the IAX2 server
phone numbers.
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
9 / 42
3StarsNet ATA User Manual
2.3 Network
2.3.1 Wan Config
WAN port network setting page.
Support static IP, dynamic obtain IP and PPPoE.
Configure Static IP:
----Enable Static;
----Set 3STARSNET ATA’s IP address in the IP Address;
----Set net mask in the Net mask field;
----Set router IP address in the Gateway;
----DNS Domain:
----Set local DNS server in the Preferred DNS and the Alternate DNS
Configure to dynamic obtain IP
----Enable DHCP;
If there is DHCP server in your local network, 3STARSNET ATA will automatically
obtain WAN port network information from your DHCP server.
Configure PPPoE:
----Enable PPPoE
----PPPoE server: Enter “ANY” if no specified from your ITSP.
----Enter PPPoE username and pin in the username and password.
3STARSNET ATA will automatically obtain WAN port network information from your
ITSP if PPPoE setting and the setup are correct.
Notice: If user accesses the gateway through WAN port. He should use the new IP
address to access the gateway when the WAN port address was changed.
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
10 / 42
3StarsNet ATA User Manual
2.3.2 LAN Config
Bridge Mode:
Enable this option to switch to bridge mode. Gateway won’t assign IP
for its LAN port in bridge mode and its LAN and WAN port will be in the same network.
(This setting won’t take effect unless you save the config and reboot the device)
IP Netmask: Set the IP and Netmask for the LAN
DHCP Server: Enable DHCP service in LAN port
NAT:
Enable NAT.
2.4 VoIP
2.4.1 SIP Config
Setting page of public SIP server:
Register Server Addr:
Register address of public SIP server
Register Server Port:
Register port of public SIP server
Register Username:
Username of your SIP account (Always the same as the phone
number)
Register Password:
Password of your SIP account.
Proxy Server Addr:
IP address of proxy SIP server (SIP provider always use the
same IP for register server and proxy server, in this case you don’t need to configure the
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
11 / 42
3StarsNet ATA User Manual
proxy server information. )
Proxy Server Port:
Signal port of SIP proxy
Proxy Username:
proxy server username
Proxy Password:
proxy server password
Domain Realm:
SIP domain, enter the sip domain if any, otherwise
3STARSNET ATA will use the proxy server address as sip domain.
Local SIP port:
Local SIP register port, default 5060
Phone Number:
Phone number of your SIP account
Register Expire Time:
register expire time, default is 600 seconds. 3STARSNET ATA
will auto configure this expire time to the server recommended setting if it is different from
the SIP server.
Detect Interval Time: Co-work with the Auto Detect Server, if Auto Detect Server is
enable, 3STARSNET ATA will periodically detect if the SIP server is available according
this setting.
RFC Protocol Edition:
Current 3STARSNET ATA SIP versions. Set to RFC 2543 if the
gate need to communicate to devices (such as CISCO5300) using the SIP 1.0. Default is
RFC 3261.
Enable Register:
Enable/Disable SIP register. 3STARSNET ATA won’t sent register
info to SIP server
DTMF Mode:DTMF signal sending mode: support RFC2833, DTMF_RELAY (inband
audio) and SIP info
Auto Detect server: co-work with Server Auto Swap and Detect Interval Time. Enable
this option, 3STARSNET ATA will periodically detect whether the public SIP server is
available, if the server is unavailable, the 3STARSNET ATA will switch to the back-up SIP
sever, and continue detecting the public sip server. 3STARSNET ATA will switch back to
the primary SIP server if the server is available again.
Server Auto Swap:Please refer to Auto Detect server for detail.
Enable Via rport: config the supporting for RFC 3581
SIP(Default Protocol): Setting for the default protocol of SIP
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
12 / 42
3StarsNet ATA User Manual
2.4.2 Iax2 Config
Setting page of public IAX server:
IAX Server Addr:
IAX Server Port:
Account Name:
Register address of public IAX server
Register port of public IAX server，default port is 4569
Username of your SIP account (Always the same as the phone
number)
Account Password: Password of your IAX account.
Local port:
Signal port of local, default port is 4569
Phone Number:
Phone number of your IAX account
Voice mail number: If the IAX support voice mail, but your username of the voice mail is
letters which you can not input with the ATA , then you use the number to stand for your
username
Voice mail text: if IAX support voice mail, config the domain name of your mail box here.
Echo test number: If the platform support echo test , and the number is test form , the
config the test number to replace the text format The echo test is to test the woring status
of terminals and platform
Echo test text: echo test number in text format
Refresh time: IAX refresh time
Enable Register: enable or disable register
IAX(Default Protocol): Set IAX 2 as the default protocol , if not the system will choose SIP
as default
Enable G.729: Using G.729 speech coding mandatory consultations
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
13 / 42
3StarsNet ATA User Manual
2.5 Advance
2.5.1 DHCP Server
DHCP server manage page.
User may trace and modify DHCP server information in this page.
Update Mode: Using DHCP updated model ,None expressed are not updated,
Update firmware update firmware is used to DHCP. Update file is used to
configure DHCP updated configuration files.
Tftp Server: Addresses using TFTP server upgrade 。
DNS Relay: enable DNS relay function.
User may use below setting to add a new lease table.
Lease Table Name: Lease table name.
Lease Time: DHCP server lease time.
Start IP: Start IP of lease table.
End IP: End IP of lease table. Network device connecting to the 3STARSNET ATA LAN
port can dynamic obtain the IP in the range between start IP and end IP.
Netmask: Netmask of lease table.
Gateway: Default gateway of lease table
DNS: default DNS server of lease table.
Notice: This setting won’t take effect unless you save the config and reboot the device
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
14 / 42
3StarsNet ATA User Manual
2.5.2 NAT
Advance NAT setting. Maximum 10 items for TCP and UDP port mapping.
IPSec ALG: Enable/Disable IPSec ALG;
FTP ALG:
Enable/Disable FTP ALG;
PPTP ALG:
Enable/Disable PPTP ALG;
Transfer Type: Transfer type using port mapping.
Inside IP:
LAN device IP for port mapping.
Inside Port:
LAN device port for port mapping.
Outside Port:
WAN port for port mapping.
Click Add to add new port mapping item and Delete to delete current port mapping item.
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
15 / 42
3StarsNet ATA User Manual
2.5.3 Net Service
HTTP Port: configure HTTP transfer port, default is 80.User may change this port to enhance
system’s security. When this port is changed, please use
http://xxx.xxx.xxx.xxx:xxxx/ to
reconnect.
Telnet Port: configure telnet transfer port, default is 23.
RTP Initial Port: RTP initial port.
RTP Port Quantity: Maximum RTP port quantity, default is 200
Notice:
Settings in this page won’t take effect unless save and reboot the device.
If you need to change telnet port or HTTP port, please use the port greater than 1024,
because ports under 1024 is system remain ports.
HTTP service if HTTP is set to 0.
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
16 / 42
3StarsNet ATA User Manual
2.5.4 QoS settings
3STARSNET ATA implement QoS based on 802.1p, The QoS is used to mark the network
communication priority in the data link/MAC sub-layer. 3STARSNET ATA will sorted the
packets using the QoS and sends it to the destination.
1.
Voice 802.1p Priority --- Configure the priority of the voice packets in 802.1p protocol.
2.
VLAN Enable --- Disable/Enable VLAN function
3.
Voice VLAN ID --- configure the Voice/signaling VLAN ID
4.
DiffServ Enable --- Disable/Enable Diffserv service
5.
DiffServ Value --- Configure Diffserv parameter. The value range : value range：
0x28,0x30,0x38,0x48,0x50,0x58,0x68,0x70,0x78,0x88,0x90,0x98,0xb8.default
is
0xb8 ,oxb8 stands for best fast transmission; 28-30 is guaThrantee for the transmission
priority for the 1st rank , 48-58 is guarantee for the transmission priority for the 2nd rank,
68-78 is guarantee for the transmission priority for the 3rd rank, 88-98 is guarantee for the
transmission priority for the 4th rank.
6.
Data VLAN ID--- Assign VLAN id for data stream.
7.
Data 802.1P Priority --- Configure the priority of the data packets (non-voice/signaling
data) in 802.1p protocol.
8. Data/Voice DiffServ differentiated --- undifferentiated for Date and voice VLAN is not
distinction VLAN tag, Tag differentiated for Date and Voice VLAN is distinction VLAN tag,
Date untagged for Date VLAN is distinction VLAN tag
Please refer to VLAN implement for detail
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
17 / 42
3StarsNet ATA User Manual
2.5.5 Advance SIP settings
This page is used to set the private sip server, stun server, and back up sip server
information.
STUN Server setting:
STUN Server Addr: configure stun server address;
STUN Server Port: configure stun server port default 3478
STUN Effect Time: stun detect NAT type circle, unit: minute.
Enable SIP STUN:
enable/disable stun.
Please refer to sip conf for the setting for how to set the public alter server.
Private Server Type The particular Private service system supplier carries out the sign
and speeches to encrypt, default is common
User can register two sip servers: public sip server and private sip server. these two sip
servers are independent from each other and running in the same time.
：
For how to configure private sip server. Please refer to sip configuration.
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
18 / 42
3StarsNet ATA User Manual
2.5.6 Digital Map
Digit map is a set of rules to determine when the user has finished dialing.
3STARSNET ATA support below digital map:
Digital Map is based on some rules to judge when user end their dialing and send the number to
the server. 3STARSNET ATA support following digital map:
----End With “#”: Use # as the end of dialing.
----Fixed Length: When the length of the dialing match, the call will be sent.
----Timeout:
Specify the timeout of the last dial digit. The call will be sent after timeout
----Prefix: User define digital map:
[ ] represents the range of digit, can be a range such as [1-4], or use comma such as [1,3,5],
or use a list such as [234]
x represents any one digit between 0~9
Tn represents the last digit timeout. n represents the time from 0~9 second, it is necessary.
Tn must be the last two digit in the entry. If Tn is not included in the entry, we use T0 as default, it
means system will sent the number immediately if the number matches the entry.
Example:
[1-8]xxx
All number from 1000 to 89999 will be sent immediately.
9xxxxxxx
8 digits numbers begin with 9 will be sent immediately.
911
Number 911 will be sent will be immediately
99xT4
3 digits numbers begin with 99 with be sent after four seconds.
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
19 / 42
3StarsNet ATA User Manual
2.5.7 Call Service Settings
User configure the value add service such as hotline, call forward, call transfer, 3-way
conference call .etc in this page
Hotline: configure hotline number. 3STARSNET ATA immediately dials this number after
hook-off if it is set.
Call Forward: Please refer to value add service for detail.
No Disturb: DND, do not disturb, enable this option to refuse any calls.
Ban Outgoing: Enable this to ban outgoing calls.
Enable Call Transfer: Please refer to value add service for detail.
Enable Three Way Call: Please refer to value add service for detail.
Enable Call Waiting: Enable/disable Call Waiting
Accept Any Call: If this option is disable, 3STARSNET ATA refuse the incoming call when
the called number is different from 3STARSNET ATA’s phone number.
No Answer Time: no answer call forward time setting.
Black List: incoming call in these phone numbers will be refused.
Limit List: outgoing calls with these phone numbers will be refused
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
20 / 42
3StarsNet ATA User Manual
2.5.8
MMI Filter
MMI filter is used to make access limit to 3STARSNET ATA Gateway.
When MMI filter is enable. Only IP address within the start IP and end IP can access
3STARSNET ATA gateway.
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
21 / 42
3StarsNet ATA User Manual
2.5.9 Audio Settings
CODEC: select the prefer CODEC; support ulaw, alaw and G729
Signal Standard:
Support CHINA, Japan and USA standard
Input Volume:
Handset in volume.
Output Volume:
Handset out volume.
G729 Payload Length: G729 payload length
VAD:
Enable/disable Voice Activity Detection
FAX Mode: select the FAX Mode
2.5.10
VPN
this page is VPN setting page , the Gateway support the VPN with UDP and L2TP
protocol .The parameters is as below
：
VPN IP After VPN registered successfully, VPN server will give an IP aggress to the
terminal . If there is a IP address shown on terminal (except for 0.0.0.0) ,it means your
VPN has registered
UDP Tunnel
VPN Server Addr register to the address of VPN server 。
：
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
22 / 42
3StarsNet ATA User Manual
：
：
VPN Server Port
Register to the port of VPN server
Server Group ID the group ID of UDP VPN
Server Area Code： the are code of VPN server
L2TP
VPN Server Addr： register to the address of VPN server
VPN User Name L2TP VPN username
VPN Password L2TP VPN password
：
：
UDPTunnel: use the UDP to visit VPN
L2TP: use the L2TP to visit VPN
Enable VPN: Enable the VPN server, you must choose UDP or L2TP type in advance
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
23 / 42
3StarsNet ATA User Manual
2.6 DialDial-Peer Settings
Please refer to “how to use dial rule?” for detail.
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
24 / 42
3StarsNet ATA User Manual
2.7 Config Manage
Save Config:
Clear Config:
save current settings.
restore to default settings.
Notice: clear config in admin mode, all settings restores to factory default; clear config in
guest modem, all settings except sip, advance sip restore to factory default.
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
25 / 42
3StarsNet ATA User Manual
2.8 Update
2.8.1
Web Update:
update gateway’s settings or firmware. Firmware file is .dlf extension when configure
file is .cfg extension, 3STARSNET ATA will auto select configure update or firmware
update according the extension.
2.8.2
FTP Update:
back up the configure file to FTP or TFTP server. Or auto update configure file from
your auto update server.
Back up configure file to your FTP/TFTP server.
* configure use .cfg extension.
2.8.3
Auto update:
3STARSNET ATA gateway support FTP and TFTP auto update. The gateway will auto
obtain the configure file from your update server if configured. To obtain the original
configure file, you can use the FTP/TFTP back up as describe above. Configure file using
module structure, user may remain the concerned modules and remove other modules.
Put the configure file in the root directory of update serve when finish editing.
Current Version: the system will display the current version number 。
Server Address: FTP/TFTP server address
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
26 / 42
3StarsNet ATA User Manual
Username: FTP server user name
Password: FTP server password
Config File Name: The name of configuration file
Config Encrypt Key: The encrypt key of confirmation file
Protocol Type: The protocol type that used for upgrading
Update Interval Time: The interval time that the terminals search for new configuration
file.
Update Mode: auto provision mode; Disable: not auto update，Update after reboot:auto
update after reboot，Update at time interval:auto update after a certain time
Configure file version was in the <<VOIP CONFIG FILE>> and <GLOBLE CONFIG
MODULE> ConfFile Version
For instance:
Gateway original version is:
<<VOIP CONFIG FILE>>Version:1.0000
<GLOBLE CONFIG MODULE> ConfFile Version：6
User may edit the configure file version to:
<<VOIP CONFIG FILE>>Version:1.0007
<GLOBLE CONFIG MODULE> ConfFile Version：7
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
27 / 42
3StarsNet ATA User Manual
2.9 System Manage
2.9.1
Account Manage
Set web access account or keypad password of AT-530.
2.9.2
Syslog Config:
Server IP: set the syslog server address
Server Port: set the syslog server port
MGR Log Level: set the MGR log level
SIP Log Level: set the SIP log level
IAX2 Log Level: set the IAX2 log level
Please click “apply” after setting
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
28 / 42
3StarsNet ATA User Manual
2.9.3
Time Set:
Server:type the ip address of time server
Timezone:select correct time zone in list box
Timeout: longest response time for SNTP
Manual Timeset:The time setting
Daylight: Daylight Saving time
2.9.4 Logout&Reboot
Reboot Gateway, some setting needs to reboot to make it works. Please always save
config before reboot, otherwise the setting will return to previous setting.
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
29 / 42
3StarsNet ATA User Manual
3
IVR setting
User may pre-config 3STARSNET ATA gateway using a normal phone connecting to
3STARSNET ATA. please refer the below command:
Notice: all command below can be end with # to speed response.
"#****"
"#*000"
/*reboot gateway*/
/*clear settings*/
"#*100"
"#*101"
"#*102"
/*set the IP type to static ip */
/*set IP type to DHCP */
/*set IP type to PPPoE*/
"#*111"
"#*222"
/*prompt gateway ip*/
/* prompt phone number*/
Below setting need reboot to take effect
"#*103" /*change to bridge mode*/
"#*104" /*change to router mode*/
"#*50192.168.1.117"
set WAN port IP address
"#*51192.168.1.1"
set default gateway IP
"#*52202.112.10.37"
set dns server
"#*53255.255.255.0” set netmask, use 255.255.255.0 if no be set
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
30 / 42
3StarsNet ATA User Manual
4 Telnet Console
4.1 Introduce
4.1.1 Basic structure
User may use telnet command to access and manage gateway.
3STARSNET ATA adopts tree structure for telnet. Every node contains its sub-nodes or
local command. User can type “help” or “?” whenever to see sub-nodes and all local
command under current node.
Besides local command, there are some global commands can be used in each node.
4.1.2 Basic command
Logout: exit telnet mode.
Write:
save current settings.
Type sub-nodes name in current node to switch to sub-node.
Type “!” or “exit” in current node to return to parent-node.
Type “help” or “?” can see all sub-nodes and all local command under current node, every
help item has comments such as <command> or <node> to distinguish sub-nodes and
local command. Type “help” or “?” in command can see all parameters using in this
command.
When typing node name or command, user no need to key the full name, use TAB button
will make it more efficient.
There are two types in command parameters: optional and required. “required” parameter
use “-” as prefix and “optional” use “_” as prefix. User may type “-” or “_” then press TAB
button for complementarily.
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
31 / 42
3StarsNet ATA User Manual
4.2 Global Command
Global command is available under all nodes, 3STARSNET ATA support
following commands:
Command
Function
Example
exit
Return to parent-node
#exit
logout
Exit
#logout
ping
Ping command, use to check network,
#ping www.google.com
write
Save setting to flash
#write
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
32 / 42
3StarsNet ATA User Manual
5 Tree Structure
5.1.1 Debug (Level 0~7)
path:
<debug>#
show debug setting
[disable]enable debug all modules
[disable]enable debug app module
[disable]enable debug cdr module
[disable]enable debug sip module
[disable]enable debug tel module
[disable]enable debug dsp module
---show
---[no] all xxx
---[no] app xxx
---[no] cdr xxx
---[no] sip xxx
---[no] tel xxx
---[no] dsp xxx
5.1.2 reload
usage: #reload
Reboot system
5.1.3 show system running info
basic
path:
<show>#
show network status
Example: #<show>#basic
Show ip packets Stat.
Example:#<show>#ip ip
Show RTP packets Stat.
Example:#<show>#ip rtp
Show TCP packets Stat.
Example:#<show>#ip tcp
Show UDP packets Stat.
Example:#<show>#ip udp
memory
path:
<show>#
show gateway memory
Example:#<show>#memory
nat
path:
<show>#
show NAT information
Example:#<show>#nat
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
33 / 42
3StarsNet ATA User Manual
uptime
path:
<show>#
show running time
Example:#<show># uptime
version
path:
<show>#
show gateway version
Example:#<show># version
5.1.4 telnet and logout
Usage: #telnet –target -port
Login:xxx
Password:xxx
#
#logout
5.1.5 tracert trace network path info
usage: #tracert –host
Example:#tracert www.google.com
6 Network Diagnosis
There are some telnet commands for checking your network. Now Listing below for your
information
Command
Function
Example
ping
Check if the destination is accessible
#ping www.google.com
tracert
Show network path info
#tracert www.google.com
show basic
Show network settings
#show basic
show ip route
Show route table
#show ip route
show ip arp
Show arp table
#show ip arp
telnet
Telnet to another device
#telnet 192.168.1.2
7 Restore to factory default
#setdefault clear gateway settings expect network part
#setdefault all clear all settings.
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
34 / 42
3StarsNet ATA User Manual
8 POST Mode(safe mode)
3STARSNET ATA provide safe mode. When there is booting problem because of setting
problem or firmware problem. User can restore the factory setting or upgrade to a new
firmware to solve this problem.
How to enter safe mode?
In the 3STARSNET ATA booting procedure, it use the static ip 192.168.1.179 (WAN port
IP) for a short time, user can telnet to this ip address in this occasion to enter the save
mode.(remember to change your PC into the network 192.168.1.xx )
Then user can according the guide in post mode to clear the settings or upgrade the
firmware.
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
35 / 42
3StarsNet ATA User Manual
9 FAQ
How many SIP
simultaneously?
servers
may
3STARSNET
ATA
register
3STARSNET ATA support 2 SIP servers and a IAX server. The Default server is SIP . If you want
to use the IAX server you must set IAX as default protocol in the IAX config page. IAX and SIP
can register simultaneously but not work simultaneously. If you set 2 SIP servers in the SIP setting
page , you can choose the route (server) by dialing plan which is edited by you. Please see “How
to use the dial rule?” for detail.
How can I know the 3STARSNET ATA’s IP address?
Pick up the handset and then dial “#*111#”, and the 3STARSNET ATA will promote you its IP
address.
How to use 3STARSNET ATA’s Lifeline function?
3STARSNET ATA supports Lifeline function, you can use the same handset to place PSTN and
VoIP calls. First, you need to set up the Lifeline with the accessory send with the 3STARSNET
ATA, connect this accessory to 3STARSNET ATA’s FXS port, and then connect the handset to the
accessory’s phone port, connect the landline to the accessory’s line port. You can receive PSNT
and VoIP calls simply with configuration. To place the PSTN call, you need to set up as follow:
----Add a new dial rule in the Dial-Peer setting: set the phone number to *T, and choose the
Lifeline as the Call mode.
----Add new Digital map item in the Advance Digital Map: set Prefix Number to and *, and the
length to 1.
Then when you want to place a PSTN calls, you can first press * to switch to the PSTN line and
then place your call as you normal do.
Why the settings vanish after reboot?
Please go to Config ManageSave Config to save your setting always.
How to use the dial rule?
3STARSNET ATA provide flexible
dial rule, with different dial-rule configure, user can
easily implement the following function:
----Replace, delete or add prefix of the dial number.
----Make direct IP to IP call
----Place the call to different SIP server according the prefix.
----Make PSTN calls use Lifeline function (Please refer “How can use the Lifeline function of
3STARSNET ATA?”).
You can click “Add” to add a new dial rule. Below is the detail setting of the dial-rule:
Phone Number: The Number suit for this dial rule, cam be set as full match or prefix match. Full
match means that if the number user dialed is completely the same as this number, the call will use
this dial-rule. Prefix match means that if prefix of the number that the user dials is the same as the
prefix, the call will use this dial-rule, to distinguish from the full match case, you need to add “T”
after the prefix number in the phone number setting.
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
36 / 42
3StarsNet ATA User Manual
Call Mode: support SIP and Lifeline，SIP means the call will use sip protocol，Lifeline means the
call will use the PSTN line.
Destination (optional): call destination, can be IP or domain. Default is 0.0.0.0, in this case the
call will be routed to the Public SIP server. If you set the destination to 255.255.255.255, then the
call will be routed to the private SIP server. Also you can key other address here to make direct IP
calls
Port (optional): Configure the port of the destination, default is 5060
Alias (optional):Set up the Alias. We support four Alias as below. Alias need to co-work with the
Del Length:
add:xxx, add prefix to the phone number, can set to reduce the dial length.
all: xxx, replace the phone number with the xxx, can use as speed dial function.
del, delete the first N numbers. N is set in the Del Length
rep:xxx，replace the first N numbers. N is set in the Del Length. For Example: Use wants to
place a call 8610-62281493, then you can set the phone number in the dial rule as 010T, and set
the Alias as rep:8610, and set the Del Length to 3. Then all calls begin with 010 will be changed to
8610 xxxxxxxx.
Suffix (optional):Configure suffix, show no suffix if not set
Instance:
2T rule: If the call starts with 2, the first 2 will be deleted, and the rest number will be sent to
private server.
3T rule: If the call starts with 3, the first 3 will be deleted, and the rest number with be sent to
public server.
123 rule: Dial 123 and will send 8675583018049 to your server. Used as speed dial function.
0T rule: If the calls is begin with 0, the first 0 will be replace by 86. Means that if you dial
075583018049 and 3STARSNET ATA will send 8675583018049 to your server.
*T rule: Dial the * and the line with switch to PSTN. Note that you need to set another rule
“Prefix Number: *; Length: 1” in the Digital Map. (Refer “How to use 3STARSNET ATA’s
Lifeline Function?”)
179 rule: when you dial 179 , the call with send to 192.168.1.179, suit for LAN application
without set up a sip server.
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
37 / 42
3StarsNet ATA User Manual
How to use speed dial function?
Please refer to “How to use dial rule?”.
How to configure digital map?
Please refer digit map settings.
How to use Call Forward, Call Transfer and 3-way Conference
calls?
User may set up the configuration in the Call Service page to use these value add service.
Call Forward:
----Forward when busy: select Busy in the Call Forward Field, and Key in the destination phone
number in the Forward Number. If some one calls you when you having a call, the caller will be
forwarded to the destination number.
----Forward no answer: Select No Answer in the Call Forward Field, and Key in the destination
phone number in the Forward Number, fill the time in the No Answer Time. If some one calls you
and no one answer the caller during the No Answer Time, the call will be forward to the
destination number.
----Forward Always: Select Always in the Call Forward Field, and Key in the destination phone
number in the Forward Number, then any one calls this gateway will be forward to the destination
number.
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
38 / 42
3StarsNet ATA User Manual
Call Transfer:
Check the Enable Call Transfer.
If A is the 3STARSNET ATA user, and B calls and talking with A through VoIP. A can press the
Hook-Flash to hold the call with B, and then press * and then enter C’s number. B will be
transferred to C and can talk with C.
3-Way Conference Calls
Check Enable Three Way Call
Only sip protocol support this function .Assume A is the 3STARSNET ATA user, and B calls and
talking with A through VoIP. A can press Hook-Flash to hold the call with B, then enter C’s
number to talk with C, and then press Hook-Flash again switch back to user B , then A can
press * to make 3-way conference calls.
Notice: A can press Hook-Flash to switch between B and C. or press # to cancel the current call
and switch to the other user.
VLAN implement
3STARSNET ATA support rich 802.1Q/P protocol and Diffserv configuration.
Through its flexible VLAN function, you can set the voice/signaling and data packets
in different VLAN via different VLAN id.
Different implement of VLAN function:
1: if “Data/Voice VLAN differentiated” is undifferentiated. Device will set the same
vlan ID for voice and data. As show below
Or
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
39 / 42
3StarsNet ATA User Manual
2.
if “Data/Voice VLAN differentiated” is Tag differentiated but the DiffServ is
disable. Device won’t distinguish the voice, signaling and data stream. It will add the
same data vlan id to them. As below:
Or
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
40 / 42
3StarsNet ATA User Manual
3. if “Data/Voice VLAN differentiated” is Tag differentiated and diffServ are both
enable. Then device will distinguish the voice, signaling and data stream to VLAN ID
setting. As below:
Or
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
41 / 42
3StarsNet ATA User Manual
4.if “Data/Voice VLAN differentiated” is Date untaged and diffServ are both enable.
Then device will undistinguish the date to VLAN ID setting. As below:
5. if VLAN is disable. Device won’t add any vlan ID to the stream. In this case, if the
Diffserv is enable, the DiffServ value response to the voice/signaling stream.
6. When VLAN function is enable. If “VLAN ID check” is enable, 3STARSNET ATA
will have strict requirement on the VLAN, it won’t handle any packets with different
VLAN ID. If “VLAN ID check” is disable, 3STARSNET ATA will handle the packets
even from different vlan ID. Please notice that VLAN ID check is enable in default.
3StarsNet NV/SA, Gulledelle 92, 1200 Brussels, Belgium. Tel: 078.077.999 – Fax: 078.077.078
42 / 42
">