SKC EPAM 5000 Environmental Particulate Air Monitor User's Guide

PDF

Document

USER’S GUIDE

SKC

ENVIRONMENTAL PARTICULATE

AIR MONITOR

MODEL SKC EPAM-5000

DOC# HD50706

SKC Inc.

863 Valley View Road

Eighty Four, PA 15330

Phone: (724) 941-9704

Fax: (724) 941-1369

Manufactured By: Environmental Devices Corporation

Model

SKC EPAM-5000

User’s Guide

Licenses, Copyrights and Trademarks

This documentation contains trade secrets and confidential information proprietary to Environmental Devices Corporation (EDC). The software supplied with the instrumentation, documentation and any information contained therein may not be used, duplicated or disclosed to anyone, in whole or in part, other than as authorized in a fully executed EDC End User

License or with the express written permission of EDC.

Haz-Dust ™ is a registered trademark of Environmental Devices Corporation.

Other trademarks are the property of their respective holders. ii

Safety Notice

Repair of instrumentation supplied by Environmental Devices Corporation

(EDC) should only be attempted by properly trained service personnel, and should only be conducted in accordance with the EDC system documentation.

Do not tamper with this hardware. High voltages may be present in all instrument enclosures. Use established safety precautions when working with this instrument.

The seller cannot foresee all possible modes of operation in which the user may attempt to utilize this instrumentation. The user assumes all liability associated with the use of this instrumentation. The seller further disclaims any responsibility for consequential damages. iii

Warranty

Environmental Devices Corporation (EDC) warrants only non-expendable products (expendable items include batteries disposable filters and cassettes or other consumables), parts and labor, for a period of one year from date of shipment to the original purchaser. The warranty covers only product parts and labor that failed due to normal operation of the instrument and not due to abuse or negligence. The product will be delivered in accordance to its published specifications and free from defects in materials or workmanship.

If a product fails to conform to this one year limited warranty it may be returned to the factory for repair or replacement of the defected part(s). EDC must be notified of all returning warranty repair products, either in writing or by telephone. Shipping and insurance cost will be prepaid by the purchaser.

EDC makes no other express warranty and disclaims any implied warranty of fitness or merchantability. iv

Licenses, Copyrights and Trademarks ...................................................................................................................ii

Safety Notice .........................................................................................................................................................iii

Warranty................................................................................................................................................................iv

Table of Contents ...................................................................................................................................................v

Chapter 1 - Introduction to the SKC EPAM-5000 .............................................................................................. 1-1

Introduction to the SKC EPAM-5000 ............................................................................................................... 1-2

Overview of the SKC EPAM-5000 ................................................................................................................... 1-4

Real-Time Dust Monitoring Principles .............................................................................................................. 1-6

Features .............................................................................................................................................................. 1-7

Specifications ..................................................................................................................................................... 1-8

Components........................................................................................................................................................ 1-9

Chapter 2 - Operating Parameters of the SKC EPAM-5000 ............................................................................. 2-1

Turning the SKC EPAM-5000 On and Off........................................................................................................ 2-2

Using the Menu .................................................................................................................................................. 2-3

Setting the Date and Time .................................................................................................................................. 2-4

Setting the Alarm................................................................................................................................................ 2-5

Clearing the Memory.......................................................................................................................................... 2-6

Chapter 3 - Operating the SKC EPAM-5000 ...................................................................................................... 3-1

Selecting the Particle Size..... ............................................................................................................................. 3-2

1.0um Dust Particulates...................................................................................................................................... 3-3

2.5um Dust Particulates..................................... .................................................................................................3-4

10um Dust Particulates………………………………………………………………………………………...3-5

Auto-Zero ......................................................... ..................................................................................................3-6

Manual-Zero....................................................................................................................................................... 3-7

Sampling............................................................................................................................................................. 3-9

Location Codes................................................................................................................................................. 3-12

Reviewing Stored Data..................................................................................................................................... 3-13

Chapter 4 - DustComm Pro V.1.2.......................................................................................................................... 4-1

Introduction to DustComm Pro V.1.2 ................................................................................................................ 4-2

Installing DustComm Pro ................................................................................................................................... 4-3

Loading DustComm Pro..................................................................................................................................... 4-4

Menu Selections ................................................................................................................................................. 4-5

File Menu Command ......................................................................................................................................... 4-6

Downloading Data.............................................................................................................................................. 4-8

DustComm Pro Window .................................................................................................................................. 4-11

Translating Data into ASCII Text File. ............................................................................................................ 4-14

Generating a Plot.............................................................................................................................................. 4-15

Data Plot Menu Selections ............................................................................................................................... 4-16

Editing a Title................................................................................................................................................... 4-17

Applying a Correction Factor........................................................................................................................... 4-18

Inability to Download....................................................................................................................................... 4-19

Chapter 5 - Maintenance ........................................................................................................................................ 5-1

Checking the Calibration Span........................................................................................................................... 5-2

Checking the Flow Rate ..................................................................................................................................... 5-5

Adjusting the Flow Rate..................................................................................................................................... 5-7

Battery Maintenance........................................................................................................................................... 5-8

Cleaning the Sensor Optics .............................................................................................................................. 5-11 v

Chapter 6 - Troubleshooting .................................................................................................................................. 6-1

If Instrument Does not Respond......................................................................................................................... 6-2

If Memory Full Appears on Display .................................................................................................................. 6-4

Flow Rate Not Achievable ................................................................................................................................. 6-5

Inability to Download Data to PC ...................................................................................................................... 6-6

Appendix A - Menu Screens ...................................................................................................................................A-1

Appendix B - NIOSH/OSHA Particulate Air Monitoring Reference .................................................................B-1

Appendix C - Glossary of Terms............................................................................................................................C-1

Appendix D - SKC EPAM-5000 Accessories ........................................................................................................D-1 vi

Chapter 1 - Introduction to Model SKC EPAM-5000

Chapter 1 Introduction to Model SKC EPAM-5000

Chapter Overview

Introduction This chapter gives a complete overview of Model SKC EPAM-5000.

This chapter:

•

Introduces and describes EPAM-5000.

Explains operating principles of the EPAM-5000.

Identifies features, specifications and components of EPAM-5000.

In this chapter This chapter contains the following topics.

Introduction to the EPAM-5000

Overview of the EPAM-5000

1-2

1-4

Real-Time Dust Monitoring Principles 1-6

Features 1-7

Specifications 1-8

Components 1-9

1 - 1

Introduction to the SKC EPAM-5000

Introduction The SKC EPAM-5000 is a high sensitivity real-time particulate monitor designed for ambient environmental and indoor air quality applications. This unit combines traditional filter techniques with real-time monitoring methods.

These techniques combined overcome limitations of all other aerosol monitoring products.

Figure 1.2. Picture of the Haz-Dust.

Continued on next page

1 - 3

Introduction to the SKC EPAM-5000,

Continued

Comparison of methods

The traditional and real-time dust monitoring methods are described below.

Description of traditional method

Air is drawn by a vacuum pump through a 47mm diameter membrane filter

EPA FRM Style. The fibers and particles collected on the membrane filter must be counted or weighed in a laboratory for further analysis.

Advantages of traditional

method 1

Description of real-time method

Advantages of real-time method 1

• EPA or OSHA compliance reference method.

• High level of specificity and accuracy.

• Collection of dust particles, which are available for further chemical analysis.

Dust particles are drawn into the sensor head and are detected once every second. Dust concentrations are instantaneously calculated and displayed on the SKC EPAM-5000’s LCD. All data points are stored in memory for later analysis.

• Immediate estimations of the concentration of a contaminant, permitting on-site evaluations.

• Provision of permanent 24-hour records of contaminant concentrations using continuous monitors.

• Internal audible alarm to warn workers of approaching hazardous situations.

• Reduction of number of manual filter tests.

• Reduction of number of laboratory analyses.

• Provision of more convincing evidence for presentation at hearings and litigation proceedings.

• Reduced cost of obtaining individual results.

1 “The Industrial Environment - It’s Evaluation & Control”, U.S. Department of Health & Human Services, CDC,

NIOSH, 1973.

1 - 4

Overview of the SKC EPAM-5000

Ease of use

General

Information

• The user controls all functionality and programming using menus displayed on a high contrast LCD.

• A 24-hour rechargeable battery capacity.

• Automatic clean air purging of sensor for increased stability and accuracy.

• Internal temperature compensation for ambient use.

• The LCD displays real-time concentration in milligram per cubic meter

(mg/m 3 ) in accordance with EPA or OSHA Reference Methods.

• Statistical information of TWA, STEL, Max and Min levels can be viewed instantly.

• The SKC EPAM-5000 is calibrated using Arizona Road Dust (ARD) against NIOSH method 0600 for Respirable dust with a + 10% accuracy.

• The calibration of the SKC EPAM-5000 can be adjusted to compensate for changes in particle composition and distribution.

Figure 1.4. Diagram showing breathing zones of Inhalable, Thoracic, and Respirable dust particles.

Continued on next page

1 - 5

Overview of the SKC EPAM-5000,

Continued

DustComm Pro

Software

DustComm Pro supplied software is designed for more detailed analysis of sampled data. Pull down menus provide for a user friendly environment to store and analyze data and print management ready reports

Data can easily be exported in comma-delimited ASCII Text Files importable into spreadsheet programs such as Microsoft Excel and Lotus

1-2-3.

DustComm Pro Software is used for downloading the information on

Windows XP, 2000, NT, and ME PCs.

The data plots provided with DustComm Pro enable:

· Detailed statistical analysis.

· Creation of graphics and charts.

· Mathematical correction of particle characteristics when aerosol significantly differs from calibration dust.

1 - 6

Real-Time Dust Monitoring Principles

Principles • The SKC EPAM-5000 uses the principle of near-forward light scattering of an infrared radiation to immediately and continuously measure the concentration in mg/m 3 of airborne dust particles.

• This principle utilizes an infrared light source positioned at a 90-degree angle from a photo detector.

• As the airborne particles enter the infrared beam, they scatter the light. The amount of light received by the photo detector is directly proportional to the aerosol concentration.

• A unique signal processes internally and compensates for noise and drift.

This allows high resolution, low detection limits and excellent base line stability.

Figure 1.5. Diagram showing the principle of near-forward light scattering used in the SKC

EPAM-5000.

Light Scattering vs. Gravimetric Filter

0.8

0.6

0.4

0.2

ARD

Filter

0.2

0.4

0.6

Gravimetric Filter Weight

0.8

ARD = Arizona Road Dust

RTD = Real-Time Dust

Figure 1.6. Graph illustrating the principle of near-forward light scattering.

1 - 7

Features

Introduction

Real-time display of

Functional features

Operational features

Data management

The EPAM-5000 provides a unique combination of features to provide superior data quality, ease of use, and flexibility to the user. Below is a partial list of distinctive features.

• Particulate exposure levels.

• TWA, STEL, Min, and Max levels.

• PM 1.0, PM 2.5, PM 10, or TSP.

• Stored data by location code.

• Calibrated to NIOSH methods for lung damaging particles.

• In line concurrent filter samples for gravimetric analysis.

• High sensitivity of 0.001 to 20 mg/m 3 (1 µg/m 3 – 2000 µg/m 3 ).

• Interchangeable size-selective sampling inlets.

• Internal air sampling pump.

• Auto purging sensor.

• Easy user access to rechargeable battery and internal filter.

•

• On-screen programming of sampling and data storage parameters.

Real-time clock.

User selectable audible alarm.

In-field zero and span check of instrument calibration.

• Choice of 1 second, 1 minute, 10 second, or 30 minute averaging/storage intervals.

• Up to 15 months of sample/record time.

• Memory storage of up to 21,600 data points, which can be, distributed into a maximum of 999 location files.

• Data translation to ASCII text files, importable into Excel or Lotus 1-2-3.

• DustComm Pro software offers comparative graphical and statistical analysis.

1 - 8

Specifications

Introduction The EPAM-5000 meets the following specifications.

Specifications

Display: Large alphanumeric LCD- 4 line, 20-character display

Operation: Four key splash proof membrane switch – menu driven

Calibration: NIOSH gravimetric method

Sensing range: .001-20.0 mg/m 3 .01-200.0 mg/m 3 (optional)

Particle size range: 0.1-100 µm

Precision: +/- 0.003 mg/m 3 (3 µm/m 3 )

Accuracy: +/-10% to NIOSH #0600 using ARD

Sampling flow rate: 1.0 – 4.3 liters/minute

Filter cassette: 47mm disposable EPA FRM Style

Alarm output: 90db at 3ft.

Recording time: 1 sec. To 15 months

Sampling rate: 1 sec., 10 sec., 1 min., and 30 min.

Data storage: 21,600 data points

Security code: 4-digit combination

Memory & time storage: > 10yrs

Real-time clock & data display

Data display: concentration in mg/m 3

& TWA, MAX, MIN, STEL, DATE/TIME

Digital output: RS-232

Operating Temperature: -10 o C to 50 o C

Storage Temperature: -20 to 60 o C

DustComm Pro software: Windows ™ driven for graphical and data translation

Power: Rechargeable battery

Operating time: > 24 hours

Charging time: 22 hours

Humidity: 95% non-condensing

Dimensions (case): 14.0” x 6.0” x 10.0”

Weight: 12 lbs.

1 - 9

Components

Components

The following components ship with the SKC EPAM-5000.

• SKC EPAM-5000 Monitor.

• Rechargeable battery pack.

• Battery charger.

• Trimming tool.

• EPAM Media CD-ROM Includes: DustComm Pro Software and Instruction

Manual.

• RS232 9-pin serial cable (female to male).

• TSP Sampling inlet (1.0 µm, 2.5 µm, or 10 µm sampling inlet optional.

• Flow Audit Measuring Device Adapter

• Flow Audit Measuring Device.

Figure 1-7 EPAM-5000

Sampling

Inlet

Sleeve

Flow Audit

Measuring

Device

Trimming tool

RS232 9-pin serial cable

Sampling Inlet

DustComm Pro

Software

And Manual

Battery

Charger

1 - 10

Chapter 2 - Operating Parameters of the SKC EPAM-5000

Chapter 2 Operating Parameters of the EPAM-5000

Chapter Overview

Introduction

In this chapter

This chapter describes the steps involved in starting the EPAM-5000 and configuring its operating parameters.

Note: The EPAM-5000 is preprogrammed with default settings of 1 minute Sampling rate. If user desires not to change default settings then the user only needs to turn unit on and press enter button to run monitor.

This allows for immediate sampling for emergency response.

This chapter contains the following topics.

2-2

2-3

2-4

2-5

2-6

Turning the EPAM-5000 on and off.

Using the Menu.

Setting the Date and Time.

Setting the Alarm.

Clearing the Memory.

2 - 1

Keypad

Turning the SKC EPAM-5000 On and Off

Introduction Power can be supplied to the SKC EPAM-5000 either from its internal battery or from the provided AC power transformer (Battery Charger).

Note: T HE BATTERY SHOULD BE FULLY CHARGED before each use. To charge battery use the EDC supplied charger only. LED indicator on battery holder will turn green when the battery is fully charged. Charge time is approximately 22 hours and will run for approximately 24 hours. To check battery status see Page 5-8.

Power-On

Power-Off

Press the ON/OFF key to turn the EPAM-5000 monitor on.

Result: The unit will turn on and the Title Screen will appear.

Press the ON/OFF key a second time to turn the SKC EPAM-5000 off.

Figure 2.1. Diagram of Key Pad on EPAM-5000.

ENT

I/O

Keypad

Legend

2 - 2

Arrow

Down

Arrow

Enter

Button

On/Off

Button

Using the Menu

Introduction The EPAM-5000 menu appears on the 4x20-character liquid crystal display

(LCD).

Note: See Appendix A for menu option flow charts.

Accessing the main menu

Press ENTER from the Title Screen to access the Main Menu.

Using the menu The EPAM-5000 is operated using the following menu selections.

<ON/OFF>

<ENTER>

< → >

↑ >

↓ >

Selection Function

Turns the EPAM-5000 on and off.

Activates the selected option.

Selection Arrow located on the LCD display. Indicates the selected menu option.

Scrolls the Selection Arrow up one line in a menu list.

Scrolls the Selection Arrow down one line in a menu list.

EPAM-5000

Particulate

Air Monitor

E.D.C. Ver 1.5 2/99

Figure 2.2. The Title Screen of the EPAM-5000.

→ Run

Review

Functions

Span

Figure 2.3. The Main Menu of the EPAM-5000.

2 - 3

Setting the Date and Time

Introduction The date and time are pre-set by the factory to Eastern Standard Time and are maintained by an internal clock. It may be necessary to change the date and time due to local time zones or daylight savings time.

Note: It is important that the system date and time are correct for accurate record keeping.

Date and Time settings

Time is entered and displayed in military time format.

Date is entered and displayed in European format (i.e., MON 17-DEC-01).

View settings Follow the steps in the table below to check the unit’s date and time.

Step Action

1 Select Special Functions from the Main Menu.

2 Select Date/Time.

3 Select View Date/Time.

Result: The unit’s current date and time will display.

4 Press ENTER to return to the View Date/Time Screen.

Change settings Follow the steps in the table below to change the unit’s date and time.

Step Action

1 Select Special Functions from the Main Menu.

2 Select Date/Time.

3 Select Set Date/Time.

4 Enter the correct date and time using the steps in the table below.

To... Press...

Increase the value of the selected digit. < ↑ >

Decrease the value of the selected digit. < ↓ >

Select the next digit or field. ENTER

5 Press ENTER when the correct information has been entered.

To... Select...

Update the selected date and time.

Return to the Date/Time screen without saving changes.

Set Date/Time

Cancel

2 - 4

Setting the Alarm

Introduction

Alarm settings

An audible alarm can be set to alert the worker of approaching threshold limits.

The concentration level must be set to the defined agency standard for the particulate type being sampled.

Note: See Appendix B for a partial listing of the most common dust particulates and their corresponding concentration levels.

Using the alarm Follow the steps in the table below to set the alarm level.

Step Action

1 Select Special Functions from the Main Menu.

2 Select Set Alarm.

3 Enter the appropriate concentration level using the table below.

To... Press...

Increase the value of the selected digit.

< ↑ >

Decrease the value of the selected digit.

< ↓ >

Select the next digit. ENTER

4 Press ENTER after the last digit is entered.

5 To run unit with alarm select Alm-Continue, or Alm-overwrite to activate alarm setting in run mode.

Result: The alarm has been set and the Main Menu appears.

2 - 5

Clearing the Memory

Introduction

Clearing memory

The memory of the EPAM-5000 can be cleared at any time.

Note: All data points in all locations will be deleted from memory.

Follow the steps in the table below to clear the memory of the EPAM-5000.

Step Action

1 Select Special Functions from the Main Menu.

2 Select System Options.

3 Select Erase Memory.

4 Select Yes to clear memory.

Note: Selecting No will cancel the process without clearing memory.

2 - 6

Chapter 3 - Operating the SKC EPAM-5000

Chapter 3 Operating the SKC EPAM-5000

Chapter Overview

Introduction This chapter describes and diagrams operation procedures of the EPAM-

5000.

In this chapter This chapter contains the following topics.

Selecting the Particle Size:

1.0 micron Dust Particulates

2.5 micron Dust Particulates

10 micron Dust Particulates

3-2

3-3

3-4

3-5

Auto-Zero 3-6

Manual-Zero 3-7

Sampling 3-9

Location Codes 3-12

Reviewing Stored Data 3-13

3 - 1

Selecting The Particle Size

Introduction The inlet system of the SKC EPAM-5000 can be configured to sample TSP,

PM 1.0, 2.5, 10.0 µm dust particulates. The following pages detail the selection process for each of these particle types. Impactor Sleeve holds one optional accessory.

Figure 3-1. Picture: A) Impactor Jet, B) Impaction cup, and C) Impactor

Sleeve. For TSP sampling use impactor sleeve without impactor.

One Size Selective Inlet is provided with EPAM-5000. Impactors are engraved on bottom of jet.

3 - 2

1.0um Dust Particulates

Follow the steps in the table below to select PM-1.0 dust particulates.

Step Action

1 Select Special Functions from the Main Menu.

2 Select System Options.

3 Select Extended Options.

4 Select Size Select.

5 Select 1.0 µm – E (The letter E will be displayed on LCD during run mode to identify for the user that 1.0 µm has been selected.)

Result: The Main Menu is displayed.

6 Insert the sampling inlet into the sensor head of the

EPAM-5000.

Note: If also collecting concurrent 47mm EPA FRM Style filter samples place a clean gravimetric filter in the filter cassette. The flow rate should be checked each time a new gravimetric filter is used. See page 5-5 for information on checking the flow rate.

7 Attach the filter cassette to the sensor head of the EPAM-5000.

See diagram below.

8 Turn to page 3-7 and follow the instructions to Manual-Zero the

EPAM-5000.

Install 47mm filter if desired.

Remove filter holder by unscrewing bottom round cover.

Figure 3-2. Diagram of sensor lid. To unlock sensor lid unscrew pem screw located on right side of sensor lid to expose the filter cassette. *NOTE: When closing sensor cover be sure not to tighten pem screw too tightly the spring inside the screw can break.

3 - 3

2.5um Dust Particulates

Note: 2.5-µm size select is the default setting of the EPAM-5000.

Follow the steps in the table below to select PM2.5 dust particulates.

Step Action

1 Select Special Functions from the Main Menu.

2 Select System Options.

3 Select Extended Options.

4 Select Size Select.

5 Select 2.5.

Result: The Main Menu is displayed.

6 Insert the inlet into the sensor head of the EPAM-5000.

Note: If also collecting concurrent 47mm EPA FRM Style filter samples place a clean gravimetric filter in the filter cassette. The

Flow Rate should be checked each time a new gravimetric filter is used. See page 5-5 for information on checking the flow rate.

7 Attach the filter cassette holder to the sensor of the EPAM-5000.

8 Turn to page 3-7 and follow the instructions to Manual-Zero the

EPAM-5000.

3 - 4

10um Dust Particulates

Selecting PM-

When using the SKC EPAM-5000 monitor for PM-10 sampling a suitable entry must be used.

Follow the steps in the table below to select PM-10 dust particulates.

Step Action

1 Select Special Functions from the Main Menu.

2 Select System Options.

3 Select Extended Options.

4 Select Size Select.

5 Select PM10.

Result: The Main Menu is displayed.

6 Insert the inlet into the sensor head of the EPAM-5000.

Note: If also collecting concurrent 47mm EPA FRM Style filter samples place a clean gravimetric filter in the filter cassette. The

Flow Rate should be checked each time a new gravimetric filter is used. See page 5-5 for information on checking the flow rate.

7 Attach the filter cassette holder to the sensor of the EPAM-5000.

See figure number 3-2 on page 3-3.

8 Turn to page 3-7 and follow the instructions to Manual-Zero the

EPAM-5000.

Continued on next page

3 - 5

Auto-Zero

Introduction

Auto-Zero

Auto-Zero purging feature automatically adjusts for baseline drift due to severe ambient temperature change.

This feature is a default setting on the EPAM-5000.

The Auto-Zero feature purges the sensor optics with clean air and reestablishes the baseline every 30 minutes.

To deactivate or reactivate the Auto Zero purging feature follow the table below.

Step Action

1 Select Special Functions from the Main Menu.

2 Select System Options.

3 Select Extended Options.

4 Select Calibration Options.

5 Select Auto Zero.

3 - 6

Manual-Zero

Introduction

Manual-Zero

Manual-Zero sets the measurement baseline of the EPAM-5000 to zero mg/m 3 . The Manual-Zero check should take place prior to beginning a new set of measurements.

Note: If using the Auto-Zero setting (default) the EPAM-5000 automatically zeroes baseline every 30 minutes.

Follow the steps in the table below to Manual-Zero the EPAM-5000.

Note: The battery should be fully charged. Check battery status as described in Chapter 5 Section 8.

Step Action

1 Be sure the appropriate sampling inlet is attached to the sensor inlet of the EPAM-5000 using the table below.

If sampling…

PM1.0 Particulates

PM2.5 Particulates

PM10 Particulates

TSP Particulates

Then insert the…

1.0 impactor jet

2.5 impactor

10 impactor jet

Impactor sleeve only

Continued on next page

3 - 7

Manual-Zero,

Continued

3 Select Special Functions from the Main Menu.

4 Select System Options.

5 Select Extended Options.

6 Select Calibration.

Result: Screen appears with manual zero at the top.

7 Select Manual-Zero.

Select Manual-Zero again.

Note: Wait approximately 99 seconds. The unit automatically executes the steps necessary to reestablish the baseline.

Result: The Main Menu is displayed when the manual-zero process is complete.

Notes:

The EPAM-5000 has an auto zero purging feature that automatically purges the sensor and performs an auto zero to reestablish the baseline approximately every 30 minutes. An X inside a box appears in right hand corner of the display when the instrument is auto zeroing.

3 - 8

Sampling

Introduction

Conditions

Sampling

Once you have selected a Particle Size and completed the Manual-Zero process the EPAM-5000 is ready to begin sampling.

The following conditions should be met before starting the sampling process.

Condition...

The correct particle size must be selected.

The correct sampling inlet must be attached.

The date and time must be checked and/or set.

The Manual-Zero process must be complete.

The alarm level must be set if sampling with the alarm feature.

For further Information

See Page...

3-2

3-2 –3-5

2-4

3-7

2-5

Follow the steps in the table below to begin the particle sampling.

Step Action

1 Turn unit on and press enter.

2 Select Run, and Choose Continue or Overwrite data.

3 Choose the memory storage type using the table below.

To... Select...

Erase all previously recorded data points in all locations.

Overwrite, then

Select Yes to confirm,

Note: Selecting No will cancel sampling process without effecting memory.

Add data points to the next consecutive location.

Continuation.

Note: See page 3-13 for explanation of location codes.

Continued on next page

3 - 9

Sampling,

Continued

4 Sample and record the data using the table below.

To Sample... Select...

Without the alarm feature

With the alarm feature

Run

Alm-Continue

Results:

• The internal pump is activated and the sampling process begins.

• The Run Screen is displayed.

Note: Maximum sampling time is based on the sampling interval selected in step number two.

B C

Figure 3.10. The Run Screen. The table below describes the diagram details.

3 - 10

Sampling,

Continued

Ending the

Sampling process

Detail Explanation

A Indicates Location Code of data being sampled. A record should be kept of the site that corresponds to each location code.

Note: See page 3-11 for explanation of location codes.

Particulate type being sampled.

1.0 µm = E

2.5 µm = S

10 µm = M

TSP = L

Concentration. A constant negative number may indicate the baseline of the unit is not set to zero and the Manual-Zero process should be performed or Auto Zero function should be turned on see Chapter 3 page 3-6.

D Battery Status Bar is displayed in the upper right hand corner when the unit is in the run mode. This status is a relative indicator of battery voltage versus time.

Press ENTER to stop data collection and return to the Main Menu.

Note: The EPAM-5000 default settings are for a size select of 2.5 µm, 1 min. sample rate with auto zero purge on.

Selecting the

Sample Rate.

Follow the steps in the table below to select the sample rate.

Step Action

1 Select Special Functions from the Main Menu.

2 Select System Options.

3 Select Sample Rate.

Select...

1 Second

10 Seconds

1 Minute

30 Minutes

For maximum sampling time of...

6 Hours

60 Hours

15 Days

15 Months

Note: A sample is taken each second and averaged by the sample interval time selected.

3 - 11

Location Codes

Introduction

Maximum location codes

The EPAM-5000 assigns a location code called tag number to each sampling sequence. The active location is indicated in the Data Record Screen (See figure 3.10).

The EPAM-5000 can store a total of 21,600 data points, which can be distributed into a maximum of 999 locations.

Assigning location codes

The location code assigned to the site is determined by the memory storage type selected in step number three of the sampling process (page 3-9).

Use the table below to identify the location code being used.

Data storage type selected...

Continuation

Overwrite

The SKC EPAM-5000 Assigns...

The Next Consecutive Value as the

Location Code.

Example: If data was previously stored in Tag #001 and #002 the data being collected will be stored in Tag #003.

001 as the Tag Number and all previously stored data points in all locations are erased.

3 - 12

Reviewing Stored Data

Introduction The EPAM-5000 provides extensive capabilities for reviewing internally stored data and statistics on the LCD or downloading to a PC using

DustComm Pro Software (Chapter 4).

LCD display The following information can be displayed on the LCD.

Date

Start

Stop

Time

Display Description Tag #

Date of sampling.

Time sampling began.

Time sampling was terminated.

Time of occurrence of reported statistic.

MAXIMUM Sample Highest concentration of dust particles.

MINIMUM Sample Lowest concentration of dust particles.

T.W.A. Time weighted average concentration of dust particles.

Elapsed

S.T.E.L.

Elapsed time of the time weighted average.

Short-term exposure limit.

Viewing data on the LCD

Follow the steps in the table below to review stored information and statistics.

Step Action

1 Select Review Data.

2 Select Statistics.

3 Determine your next step using the table below.

If... Then

Memory holds data points in other locations.

The Scanning Memory

Screen displays. Go to step 7.

Memory has been cleared of all data points.

To review...

A different Location

No Data Recorded.

4 Select the Location using the table below.

Select...

New Tag XXX and go to step

Continued on next page

3 - 13

Reviewing Stored Data,

Continued

5 Enter the desired Location in the Location Select Screen using the table below.

To... Press...

Increase the value of the selected digit. < ↑ >

Decrease the value of the selected digit. < ↓ >

Select the next digit or field. ENTER

6 Press ENTER when the desired location code has been entered.

Result: The location is shown on the display. If the location is being reviewed for the first time scrolling dots will appear indicating the microprocessor is computing data.

7 The first of five statistics screen appears when data is computed.

Scroll through the statistics screens using the table below.

Press... To

< ↓ > Forward through the statistic screens.

< ↑ > Backward through the statistic screens.

To download data to a PC using the provided DustComm Pro Software select download from review data menu and proceed to Chapter 4.

3 - 14

Chapter 4 – DustComm Pro V.1.2

Introduction to the DustComm Software

Introduction

Spreadsheet applications

Data plots

DustComm is a powerful and flexible Windows application software package designed for use with the SKC EPAM-5000 Monitor.

DustComm is both communications software that enables stored project data to be downloaded to a PC, and a data manipulation tool, enabling detailed analysis and reporting of sampled data.

DustComm easily translates data into spreadsheet ASCII text files. These files can be open into spreadsheet programs such as Microsoft Excel

The data plots provided with DustComm enable:

• Detailed statistical analysis.

• The creation of graphics and charts.

• The mathematical correction of particle characteristics when aerosol significantly differs from calibration dust.

4- 2

Installing DustComm

Introduction

Minimum system requirements

Software installation

DustComm installation is easy and quick, the entire process should take less than 5 minutes.

Windows ME or Higher.

4 MB available disk space.

8 MB RAM.

Follow the steps in the table below to install DustComm.

Note: It is assumed that the CD-Rom Drive is the “D” Drive. Substitute D with the appropriate drive letter if necessary.

Step Action

2 Close all open applications.

4 Open My Computer

5 Select the folder named “DustComm V1.2” and double click to enter.

6 Select the icon named “Setup” and double click. See Figure1.

7 Follow the installation wizard steps.

Figure 1: DustComm Software Folder with “Setup” Selected in Windows XP.

4- 3

Loading the DustComm Software

Windows ME

Windows NT,

2000 & XP

Follow the steps in the table below to load the DustComm software if using

Windows ME.

Step Action

1 Select the Start Menu.

3 Select the folder EDC DustComm Pro 1.2

4 Select DustComm Pro 1.2

Follow the steps in the table below to load the DustComm Software if using

Windows NT, 2000 & XP.

Step Action

1 Double Click on the icon on your desktop.

NOTE: If shortcut icon does not appear on desktop follow the steps for Windows ME.

Figure 2. DustComm Screen immediately after loading software.

4- 4

Menu Selections

Introduction Figures 3 through 5 show each of the DustComm menu options.

Note: If a menu option is displayed in light type it is not available during the current task.

Opens Saved Files

Saves Current Open Files if changed

Saves Current Open Files, that have not yet been saved

Closes Open Files

Saves Current Open Files as a text file, so that you can open the data up in a spreadsheet

Exits the entire Program

Figure 3. File Menu Options.

Figure 4. Unit Menu Options.

Downloads Instrument

Selects Instrument and Com Port that you want to download

Figure 5. Location Menu Options.

Write Notes about the Open File

Print Current Open Location

Review the data in a statistical graph that was previously saved

Figure 6. Plot Menu Options.

Information about DustComm Pro 1.2

Figure 7. Help Menu Options.

4- 5

File Menu Commands

Introduction Use the File Menu option to open, save, print, close and export sampled data.

You can also use the File Menu to Exit the DustComm Pro Software

Notes:

• Data is sorted by time collected.

• Data points are reported in mg/m 3 .

Opening an existing project folder

Follow the steps in the table below to retrieve stored project data.

NOTE: A sample .dcm file is preloaded for review of software options.

Step Action

1 Select File.

2 Select Open.

3 Double click on the desired Project Folder.

Note: DustComm will save all files in My Documents, or user selected folder.

Saving a project folder

Follow the steps in the table below to store project data.

Step Action

1 Select File.

• Saving the data in the project folder for the first time, or,

• Saving an existing folder to a new name or location.

Saving an updated version of an existing project folder to the same file name and location.

1. Save As, then,

2. Type a file name for the project file.

3. Select OK.

Save

Result: The data is saved in the new project folder and the new file name is displayed in the title bar. Only with Save As with the data have a new file name and location if selected.

Continued on next page

4- 6

File Menu Commands,

Continued

Exit software Exit DustComm Pro Software in one of two ways.

Option number

1 1. Select File.

2. Select Exit.

Action

2 Single click on the “X” in the upper right hand corner of the screen.

4- 7

Downloading Data

Introduction

Downloading data

Internally stored data can be downloaded to DustComm for detailed analysis.

The three major steps used to download data from the dust-monitoring unit to a PC are listed below and detailed in the next few pages.

1. Connect the cable.

2. Prepare the PC for data transmission.

3. Prepare the dust-monitoring unit for data transmission.

Follow the steps in the table below to connect the cable for data transmission. Connect the cable

Preparing the

Step Action

1 Connect one end of the supplied RS232 cable to the dustmonitoring unit.

Note: If USB compatibility needed you will need to purchase a serial to USB adapter.

2 Connect the other end of the RS232 cable to the appropriate

COMM port on the PC.

Note: Check that both connections are secure. An intermittent connection can disrupt data transmission.

Follow the steps in the table below to prepare the PC for data transmission.

Note: Multiple locations will be separated by tabs at the bottom of the program.

Step Action

2 Select Unit and Select Properties.

3 Under the Properties selection choose your unit and the Com Port that you want to connect. Press Ok when you are finished

4 Select Unit and Select Download.

5 When the items above are finished you should see the download box appear.

Continued on next page

4- 8

Downloading Data,

Continued

Preparing the unit.

Follow the steps in the table below to prepare the unit for data transmission.

Step Action

1 Select Playback or Review Data (depending on your instrument) from the Main Menu on the unit.

2 Select Download.

3 Select To Dust Data Collector.

4 Press ENTER.

Result: The Transmitting window appears.

Note: Bars on the PC screen should increase as the unit downloads.

5 When the transmission is complete...

• The To Dust Data Collector selection screen is displayed on the units monitor. The unit may be shut off at this time.

• The downloaded data is displayed in the Project Folder on the

PC. (Figure 8).

Figure 8. Project File after data has been transmitted.

4- 9

DustComm Pro Window

Introduction

Location

Information

Each section of the DustComm Pro Window will explain a different part of the statistics.

The Location information will give you general details about the downloading statistics. Such as date, time, start/stop time, data rate, duration, how many samples where downloaded and the unit. There is also box so that you can name the location and a shortcut to type in any notes you would like to add.

Dataset

Information

Figure 9. Location Information section of the DustComm Pro Window.

The Dataset Information will tell you more specific information about the downloaded statistics. Such as type of data, the average, the Max/Min

Sample and the Max STEL.

Figure 10. Dataset Information section of the DustComm Pro Window.

Continuted on the next page

4- 10

DustComm Pro Window,

Continued

Dataset Scale

Factor

The dataset scale factor section of the DustComm Pro Window, is so that you can adjust the scale to be equal to your specific type of dust. You can read more about adjusting the scale factor on page15.

Quick Plot

Figure 11. Dataset scale factor section of the DustComm Pro Window.

The Quick Plot graph shows you a miniature version of the Full Plot. The

Full Plot button is located directly below Quick Plot can you can read more about Full Plot on pages11-14.

Figure 12. Quick Plot & Full Plot Button on the DustComm Pro Window.

4- 11

DustComm Pro Window,

Continued

Location Data The location data section shows you the milligrams per cubic meter you sampled for and the times that they were sampled at.

Figure 13. Location Data on the DustComm Pro Window.

4- 12

Translating Data to an ASCII Text File

Introduction

Translating data

Project Data must be translated into ASCII text format before it can be read by a spreadsheet application.

Follow the steps in the table below to Translate Project Data into ASCII Text format.

Note: A Project Folder must be open to access the translate feature.

Step Action

1 Select File from the Main Menu.

3 An “Export Locations” Window will appear. Select either All for all locations or select the range of locations you would like to export. Click OK when you have selected your locations.

4 An “Export To…” Window will appear. Type in the name that you would like to call your exported data and click Save.

6 When you are ready to open the data in a spreadsheet application.

Open the spreadsheet program go to the Open menu, select all files under type of file name and double click on the file you want to review. This will result in your saved data opening in your spreadsheet program.

Figure 14. Exported Excel information.

4- 13

Generating a Plot

Introduction

Generating a graph

A graph can be plotted with full plot located at the bottom of the DustComm

Pro Window.

Follow the steps in the table below to generate a graph using the DustComm

Plot menu selections.

Step Action

1 Select Plot.

2 Select Review. This option is for graphs that have already been saved.

Note: For new statistics click on the “Full Plot” Icon on the

DustComm Pro Window.

3 The result is graph will be plotted to the screen (see figure 15 below).

Continued on next page

4- 14

Data Plot Menu Selections

Introduction At the top of the data plot will be a button bar. Below is an explanation of what each button does.

1 2 3 4 5 6 7 8 9 10 11

Number Function

1 Saves plotted information as a DustComm Pro Chart (*.dcc).

2 Copies plot to a bitmap file.

Edits the title of the plot.

Page Setup Properties.

Prints the current plot.

Zooms into plot. By Highlighting from point to point that you want zoomed in on.

Returns to full screen of plot.

Adds or removes vertical lines.

9 Adds or removes horizontal lines.

10 Select the specific type of graph, i.e. bar or line graphs.

11 Changes color of the graph.

4- 15

Data Plot Menu Selections,

Continued

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Number Function

Insert arched lines.

Insert a picture. Choose the size of your picture and then right click on the box and select properties. Select the picture tab and select picture. The picture you chose will appear in the box.

Insert a text box.

Insert a callouts with text.

Change the color of your squares, ovals, text boxes and callouts.

10 Change the color of the text in your text boxes and callouts.

11 Copy squares, ovals, text boxes and callouts.

12 Paste squares, ovals, text boxes and callouts.

13 Bring squares, ovals, text boxes and callouts to front.

14 Send squares, ovals, text boxes and callouts to the back.

15 Group squares, ovals, text boxes and callouts.

16 Ungroup squares, ovals, text boxes and callouts.

17 Flip over left to right squares, ovals, text boxes and callouts.

18 Flip over up and down squares, ovals, text boxes and callouts.

19 Rotate squares, ovals, text boxes and callouts clockwise.

20 Rotate squares, ovals, text boxes and callouts counterclockwise.

21 Properties of selected squares, ovals, text boxes and callouts.

4- 16

Editing Title

Introduction A customized title can be added to a graph before printing.

Editing the title Follow the steps in the table below to add a title to the graph.

Step Action

1 Have location plotted already.

2 Select the Edit Title button on the menu bar.

3 A Window will appear where you can edit the title for what you would like its name to be.

4 Select OK when the correct title is in the box.

Result: The graph will be created with the new caption.

Figure 16. Edit Title Window.

4- 17

Applying a Correction Factor

Introduction A correction factor can be applied to the data collected with the unit to account for variances in gravimetric readings.

The correction factor is calculated by dividing the Gravimetric reading by the unit reading.

Calculating a correction factor

Applying a correction factor

Follow the steps in the table below to apply a correction factor to all data points in the current project folder.

Removing the correction factor

Step Action

1 Select the 2 nd Scale= with a box where you can type in your scale factor.

2 Type in the Scale factor.

3 After the scale factor is entered press enter.

Result: All data points in the project folder have been multiplied by the correction factor.

Follow the steps in the table below to remove the correction factor from the data points in the project folder.

Step Action

1 Select the 1 st Scale= under the Dataset Scale Factor.

Result: Data points should return to original state.

4- 18

Inability to Download Data to PC

Introduction If DustComm Software installs properly but downloading instrument to computer is unsuccessful try the following:

• Ensure that the RS232 cable connectors from the PC are tightly

screwed into place.

• Ensure that the communications settings are set appropriately in the

Download Properties screen of the DustComm program. Select Unit,

Properties to access this dialog box. The communications port must be set to the appropriate Com Port used on the PC.

• If you are experiencing problems downloading your unit’s results to your PC, and the RS232 cable connectors are secured tightly, your cable may be connected to the wrong 9-pin port on your PC. If your

PC has more than one 9-pin connection port, attach the cable to another 9-pin port and try to download the dust monitor’s results at that port. You may need to try all of your PC’s 9-pin ports before finding the correct connection.

• If the previous steps check out, try using the Windows supplied

HyperTerminal or other appropriately configured communications software to receive data when downloading from the SKC EPAM-5000

Monitor.

• If using a USB port make sure you are using the proper USB to serial adapter.

For service or Technical Questions please call 800-234-2589 or e-mail [email protected]

Chapter 5 - Maintenance

Chapter 5 Maintenance

Chapter Overview

Introduction This chapter covers the routine maintenance procedures for the SKC EPAM-

5000.

In this chapter This chapter contains the following topics.

5-2

5-5

5-7

5-8

5-11

5-12

Checking the Calibration Span. (Optional Accessory).

Checking the Flow Rate.

Adjusting the Flow Rate.

Battery Maintenance.

Cleaning the Impactors

Cleaning the Sensor Optics.

5 - 1

Checking the Calibration Span

Introduction The Span Reference Insert Part Number CS-105 is a light scattering device that provides a constant value (termed a “k” factor).

The Span Reference should be used as a reference to check factory calibration of the EPAM-5000 Monitor.

When to check the calibration span

The calibration span should be checked under the following conditions:

• Once a month with normal usage. (Normal use is twice a week).

• If the EPAM-5000 is dropped or otherwise damaged.

• The first time you use the unit to double check the factory calibration.

Note: The EPAM-5000 can be sent to SKC. Annually recalibration recommended in accordance with ISO and NIST procedures.

Conditions The following conditions must be met before checking the calibration span.

Condition... For further information see page...

The Sensor Optics must be clean.

The Environment must be clean.

The Battery must be fully charged.

5-11

---

5-7

Figure 5-1. Inserting CS-105 into SKC EPAM-5000 Sensor.

Continued on next page

5 - 2

Checking the Calibration Span,

Continued

Checking

Calibration

Span

Follow the steps in the table below to check the Span of the EPAM-5000

Monitor.

Note: Failure to follow this procedure in its entirety may cause an incorrect

“k” value reading.

Step Action

1 Turn monitor on.

2 Run monitor on a 1 (one) second sample rate for (5) minutes. See

Chapter 3 Page 3-9 Sampling.

3 With unit running select down arrow from keypad to activate Auto

Purge. An “X” will appear in the upper right hand corner to indicate sensor is purging. See Chapter 3 Page 3-6 Auto Zero

Purge if more detailed information is needed.

4 After Auto Purge is complete (x is no longer present on screen) select enter to stop monitor from running.

5 Performing the Span Check.

Step Action be lost) or select no if you want to download stored data.

5-3 After selecting yes calibrate sensor will appear.

Scale factor must reset to 1000. If not press up or down arrow as needed.

6 Remove Auto Zero filter and impactor sleeve.

7 Insert the span reference into the sensor head (see diagram 5.1 on page 5-2). Allow 2-3 minutes for reading to stabilize.

Note: Be sure the locating pin on the calibration reference slides into the locating hole on the sensor head. Also Push down on the calibration reference to be sure it is aligned properly. Slightly twist

CS-105 clockwise when positioned in alignment hole. This will ensure the CS-105 is in the exact position and ensure reproducibility when “K” value is displayed on the EPAM-5000 monitor.

8 Observe the printed “k” value on the calibration reference.

Note: The printed “k” value should match the concentration value shown on the EPAM-5000 LCD to within + 10%.

Continued on next page

5 - 3

Checking the Calibration Span,

Continued

The numbers agree within + 10%

The two numbers do not agree within

+ 10%.

THEN

The EPAM-5000 has passed the span check test.

1. Repeat the process to rule out error, then

2. Call or e-mail EDC technical support or return the EPAM-5000 for recalibration.

9 Remove Span Reference and place in its protective sleeve.

Note: Optical windows on CS-105 can not have fingerprints or contamination, please clean using KK-101 Cleaning Kit.

Note: If the CS-105 is purchased from as an after market accessory, the end user must assign “k” value. To assign “k” value repeat steps 1-7 and step 9 three times. Take an average of the three numbers you recorded to get your

“k” value.

5 - 4

Checking the Flow Rate

Introduction

Checking the flow rate

It is good technique to check the flow rate every time a new gravimetric filter is used for sampling.

Use the steps in the table below to check the flow rate.

Notes:

• When using an impactor, be sure the proper sampling inlet is attached to the sensor head.

Step Action

1 Attach your airflow calibrator to the EPAM-5000 using the table below.

If sampling... Then...

PM-10, PM-

2.5, PM-1.0 or

TSP

1. Attach one end of the calibration airflow tubing to flow adapter.

2. Connect the other end of the calibration airflow tubing to your airflow calibrator.

2 Activate the internal sampling pump using the steps below.

Step Action

1 Select Special Functions from the Main

2 Select System Options.

3 Select Extended Options.

4 Select Battery Status.

Note: Battery Status should indicate greater than 6.1 volts for fully charged battery.

3 Observe the flow rate on your air flow calibrator.

If... Then...

The flow rate is 4.0 LPM.

The flow rate is not 4.0

LPM.

No flow is present.

The flow rate is properly calibrated.

Detach the airflow calibrator tubing and continue with the “Selecting the Particle

Size” process.

The flow rate must be adjusted. See page 5-7 for instructions.

See Troubleshooting section on Chapter

5 - 7

Adjusting the Flow Rate

Introduction

Adjusting the flow rate

The flow rate must be adjusted when it does not equal 4.0 LPM.

Follow the steps in the table below to adjust the flow rate.

1 Locate the adjustment screw on the front of the EPAM-5000.

2 Use the flow adjustment screw to adjust the flow rate.

To...

Decrease the flow rate

Increase the flow rate

Turn the adjustment screw...

Counterclockwise

Clockwise

3 Record the Flow Rate.

4 Detach the airflow calibrator and calibration airflow tubing.

5 Select enter to terminate battery status sensor and return to main menu.

NOTE: Flow meter must be vertical when reading measurement.

Figure 5-2. Flow Adjustment Meter attached to EPAM-5000.

5 - 7

Battery Maintenance

Introduction The battery pack is a 6.0-volt lead acid rechargeable battery that can hold a charge for up to 24 hours. It is important to check the battery periodically and recharge when necessary.

Checking the

Battery

The battery status can be checked using the menu options on the EPAM-

5000. Use the following menu options to check the battery.

Step Action

1 Select Special Functions from the Main Menu.

2 Select Systems Options.

3 Select Extended Options.

4 Select Battery Status.

Result: The Battery Level Screen displays the charging level of the unit’s battery in VDC.

If the charge level is... Then...

6.1 VDC or higher

Lower than 6.1 VDC

The battery is fully charged.

The battery must be recharged.

See instructions on page 5-9.

Continued on next page

Note: A battery status bar is displayed in the upper right hand corner when unit is in the run mode. See Figure 3.10 in Chapter 3. This is only a relative indicator of battery status. Actual voltage is displayed under battery status menu.

5 - 8

Battery Maintenance,

Continued

Recharging the battery

Follow the steps in the table below to recharge the battery using the supplied charger.

Note: If the battery is low the sampling process will terminate and the low battery screen will display.

Step Action

1 Plug the battery charger into an electrical outlet.

2 Plug the battery charger into the battery charge jack on the top panel of EPAM-5000 Battery.

Results:

• The battery charge begins. LED indicator should be Red.

• Unit must be off or the battery must be removed from instrument for LED to be Red and charge battery.

• When LED is green battery is fully charged.

Note: Recharging time is approximately 22 hours when the instrument is not operating, and approximately 24 hours while the monitor is sampling.

CAUTION:

Do not charge in a hazardous environment. Use only the EDC approved charger designed for the EPAM-5000.

Continued on next page

5 - 9

Battery Maintenance,

Continued

Removing and replacing the battery pack

The battery pack can be removed and replaced whenever necessary.

Note: The battery of the EPAM-5000 can be recharged outside of the instrument.

Removing the battery

Follow the steps in the table below to remove the battery pack.

Step Action

1 Loosen the four retaining pem screws from the top plate of the

EPAM-5000.

NOTE: These are special inserts and the screws are attached by a spring to tighten push the screw down and turn to loosen turn the screw and it will pop on the spring DO NOT pull the screw because you will break the spring and be unable to secure your battery pack.

2 Slide the battery plate out of the unit.

3 To re-install reverse above proceeding

Figure 5-3. Diagram of battery being removed from EPAM-5000.

Continued on next page

5 - 10

Cleaning the Impactors

Introduction Impactors should be disassembled and cleaned and greased at regular intervals.

Example: You should clean impactors every thirtieth sample or once a month to start, but heavy loadings are observed on the target disk, as often as appropriate.

Cleaning the

Impactors

Follow the Steps in the table below to clean the impactors.

Step Action

1 Pushing with a pen from bottom remove the impactor through top of impactor sleeve into the palm of your free hand.

2 Rinse the impactor from top to bottom with a solvent

(hexane, white gas, lantern gas) using a squeeze bottle, paying particular attention to the impaction target disks. An acceptable alternative method of cleaning involves the use of an ultrasonic bath with mild soapy water solution.

Note: The impaction cup should be removed prior to regreasing. This is accomplished by pulling the impaction cup apart from the impactor jet gently.

Let all parts of the impactor air-dry.

Prepare a mixture of solvent and impactor grease (Apiezon ®

M, Glisseal ® Ht) or similar grease in a dropper bottle until thoroughly mixed and of a fluid consistency. Use a 1-inch length of grease to 30ml of solvent. Vigorously shake the mixture until an opaque, uniform suspension, free from grease globs, is obtained.

Put two or three drops of the solution on the impaction cup.

The drops should saturate the disk, flowing freely to the edge.

Let the impaction cup “dry” by allowing the solvent to volatilize, leaving a thin film of grease on the impaction cup.

Replace the impaction cup onto the impactor jet. Re-insert the impactor into the impactor sleeve.

5 - 11

Cleaning the Sensor Optics

Introduction Although the EPAM-5000 has an internal sensor purge it is important to keep the sensor optics of the EPAM-5000 clean to ensure the integrity of the optical sensor.

The sensor optics need to be checked every 2 months or on a weekly basis, when used in a 2 to 3 mg/m 3 T.W.A. environment.

Cleaning the

Sensor Optics

Follow the steps in the table below to clean the sensor optics.

Figure 5-4. Picture of the cleaning kit.

Continued on next page

5 - 12

Cleaning the Sensor Optics,

Continued

Step Action

1 Remove the thumbscrews located on sensor cover. See Diagram

5-3.

2 Inspect internal sensor. Inspect cavities for residual dust. Use one of the following methods to clean the surface. Blow the dust away with low-pressure air or wipe with foam tipped cotton swab. See figures 5-6, and 5-7.

3 Inspect the glass lens covers for dust.

Note: Use one of the following methods to clean the glass lens.

• Blow the dust away with low pressure air, or,

• Use a small amount of isopropyl alcohol and wipe with cotton swabs.

CAUTION: Do not spill any alcohol into the internal cavity of the EPAM-5000.

4 Replace the sensor cover.

5 Tighten the thumbscrews snugly into place.

NOTE: If thumbscrews are not tighten enough the flow of the

EPAM-5000 could be off.

Continued on next page

5 - 13

Cleaning the Sensor Optics,

Continued

Figure 5-5. Removing the sensor covers.

One cover located in front as shown in picture, the other cover is located on the right side of sensor not shown.

Figure 5-6. Dust being removed with low pressure air.

Figure 5-7. Isopropyl alcohol being applied to cotton swab.

Figure 5-8. Sensor head being cleaned with cotton swab.

5 - 14

Chapter 6 - Troubleshooting

Chapter 6 Troubleshooting

Chapter Overview

Introduction This chapter provides basic troubleshooting procedures for potential operating issues.

In this chapter This chapter contains the following topics.

If Instrument Does not Respond

If Memory Full Appears on Display.

Flow Rate Not Achievable

Inability to Download Data to PC.

6-2

6-4

6-5

6-6

6 - 1

If Instrument Does Not Respond

Introduction Check the following items if the EPAM-5000 Monitor’s LCD display is incomplete, or the display and keypad are “locked up”.

Step Action

1 If the LCD display turns on, check the battery’s voltage. (Chapter 5

Section 5-8) A depleted battery will show a charge level of 5.95

VDC or lower. Replace the depleted battery with a fully charged battery (Chapter 5 Section 10) or attach the appropriate power transformer (Chapter 5 Section 9) to the EPAM-5000 Monitor.

2 If the LCD display does not appear, remove the battery (Chapter 5

Section 10) and check the voltage across positive pin and case ground using a digital voltmeter. The battery should be recharged

(either inside or outside of the monitor) if it shows a charge level of

5.95 VDC or lower. Led battery indicator light should turn from red to green when battery is fully charged or after approximately 15 hours of charging. If the battery voltage is higher than 5.95 VDC, check the continuity of the 2-amp fuse in the battery pack at location

F1. If the fuse is blown, replace it with a new 2-amp replacement fuse. If you do not purchase your replacement fuse from EDC, be sure to replace this fuse with an identically rated component to avoid damaging the monitor.

3 If the unit is “locked up” and the buttons on the keypad are nonfunctional remove the battery (Chapter 5 Section 10). Other symptoms of instrument lock up includes: Letters scrolling across the bottom of the display or non-sensible lettering, display “locked up” on preparing compensation or two lines across display. First remove the battery and charge as stated in step 2. Then replace the battery and check battery status, if it does not appear, it may be necessary to reset the instrument. A reset switch is located inside the instrument

(NOTE: only use press the reset button as a last resort, all logged data can be lost). Lift the sensor cover, inside of the instrument is a push switch located on the PCB (see figure 6-2). Press reset switch for one second and release. If unit resets it self check battery status and date and time. If not, then press the switch and hold down as the pump and solenoid purges. (This should take 30 seconds to 1 minute). Once purge is complete the switch can be released, remove battery. Replace battery and check battery status (see chapter 5 section 8). If battery status does not appear repeat procedure. After battery status appears it is necessary to reset date and time (see

Chapter 2 section 4) for the instrument to work. Note: Always

choose over write when beginning a sampling session.

6 - 2

If Instrument Does Not Respond,

continued

Lift the sensor to reach the reset switch.

Reset Switch push in to reset.

Figure 6-2: Reset switch

6 - 3

If Memory Full Appears on Display

Step Action

1 • Clear the memory as described in Chapter 2 page 2-6.

• Lithium battery may have to be replaced. Please consult EDC certified technicians.

• Batteries are covered 90 days under warranty.

6 - 4

Flow Rate Not Achievable

Perform the following checks if the flow rate of 4 LPM is not attainable.

• Air flow meter must be vertical to ensure accurate measurements.

• Air intake tubing is attached to filter cassette.

• Air may be leaking from the sensor covers on the front and right side of optical sensor of the monitor. This can be tested quickly by operating the unit (Chapter 3 page 3 -9) and placing your palm or thumb over the inlet where the sample stream enters the unit. If this does not result in a noticeable strain on the pump, it is likely that leaks exist around the sensor covers or cassette holder. Remove the sensor covers and ensure the proper cover placement front cover must be placed on front of sensor this cover can be identified by the circular pattern on the gasket material of the cover itself and reinstall them tightly. Cassette holder must have the white filter holder ring installed and holder must be screwed on tightly to avoid air leaks.

6 - 5

Inability to Download Data to PC

If instrument will not download to

PC.

If DustComm Pro Software installs properly but downloading instrument to computer is unsuccessful try the following:

• Ensure that the RS232 cable connectors from the monitor and PC are securely in place.

• Ensure that the communications settings are set appropriately in the

Communications Setup screen of the DustComm Pro program. The communications port must be set to the appropriate COM port connector used on the PC.

• If you are experiencing problems downloading your monitor’s results to your PC, and the RS232 cable connectors are secured tightly, your cable may be connected to the wrong 9-pin port on your PC. If your PC has more than one 9-pin connection port, attach the cable to another 9-pin port and try to download the monitor’s results at that port. Some PCs can have up to eight 9-pin ports. You may need to try all of your PC’s 9-pin ports before finding the correct connection.

• If the previous steps check out, try using the Windows -supplied

HyperTerminal or other appropriately configured communications software to receive data when downloading from the EPAM-5000 Monitor.

If software does not install properly:

• Ensure DustComm Pro Software is being installed on the C: Drive

EPAM5000 Subdirectory.

For service or Technical Questions please call 603-378-2112 or e-mail [email protected]

6 - 6

Appendix

Appendix A

Menu Screens

Introduction This Appendix contains a complete overview of the Menu Screens for the

EPAM-5000.

The following pages show diagrams of the Main Menu Screens, the Run

Screens, the Review Data Screens, and the Special Functions Screens.

Note: Selecting CANCEL from any Menu Screen will back out of the current function.

Appendix A

Run - continue

Run - overwrite

ALM - continue

ALM - overwrite

Run

Main Screens

Title Sceen

EPAM-5000

Particulate

Air Monitor

E.D.C. Ver 1.5 2/00

Run

Review Data

Special Functions

Span Check

Main Menu

Statistics

Download

Cancel

Playback

System Options

Date/Time

Set Alarm

Cancel

Special Functions

EPAM-5000

Particulate

Air Monitor

E.D.C. Ver 1.5 2/00

Title Screen

Appendix A

Sample/Record Screens

Run

Review Data

Special Functions

Span Check

Main Menu

Run - continue

Run - overwrite

Alm - continue

Alm - overwrite

Run Screen

Tag: 001 run

Date: TUE 12-JAN-97

Time: 07:23:38

Conc: S 2.75 mg/m³

Run Screen

Yes

* Confirm overwrite

of data

Confirmation Screen

Appendix A

Playback Screens

EPAM-5000

Particulate

Air Monitor

E.D.C. Ver 1.5 2/00

Title Screen

Run

Review Data

Special Functions

Span Check

Main Menu

Statistics

Download

Cancel

Review Data Screen

*****************************

Scanning memory

******************************

Scanning Memory Screen

Tag: 002 *STATS*

Date: Tues 26-JAN-97

Start: 08:55:21

Stop: 09:31:55

Stats Screen 1

** MAXIMUM **

Date: TUE 26-JAN-97

Time: 08:55:21

Conc: s 0.17 mg/m³

Stats Screen 2

**MINIMUM**

Date: TUE 26-JAN-97

Time: 08:55:21

Conc: s 0.0 mg/m³

Stats Screen 3

** T.W.A.**

Date: TUE 26-JAN-97

T.W.A.: 0.08mg/m³

Elapsed:0:00:32

Stats Screen 4

** S.T.E.L.**

Date: TUE 26-JAN-97

STEL: 0.432 mg/m³

Time: 14:23:28

Stats Screen 5

EPAM-5000

Particulate

Air Monitor

E.D.C. Ver 1.5 2/00

Title Screen

Run

Review Data

Special Functions

Span Check

Main Menu

System Options

Date/Time

Set Alarm

Cancel

Special Functions

Extended Options

Sample Rate

Erase Memory

Cancel

System Options

Size Select

Calibration

Battery Status

Cancel

Extended Options

1.0 um - E

2.5 um - S

10 um - M

T.S.P. - L

Size Select

Appendix A

Special Functions Screens

** Set ALARM **

Conc: 000.00 mg/m³

Set Alarm

** Battery Level **

Status: 7.44 Volts

Battery Status

Yes

Erase Memory?

* DATA WILL BE LOST

Erase Memory

View Date/Time

Set Date/Time

Cancel

Date/Time

** Current **

Date: TUES 19-JAN-97

Time: 21:12:55

Set Date/Time

View Date/Time

Time: 0 : :

Date: - -

Day:

Sensor Calibrate

Manual Zero

Auto Zero

Cancel

Manual Zero

Cancel

Calibrate

***************************

Manual-Zeroing

Please Wait

***************************

Appendix B

NIOSH/OSHA Particulate Air Monitoring Reference

Dust/Hazard alpha-Alumina (Respirable fraction) alpha-Alumina (Total dust)

Aluminum, Pyro powders

Agency Reference TWA

OSHA CIM 5 mg/m 3

OSHA CIM 15 mg/m 3

STEL

OSHA CIM *

5 mg/m 3 Aluminum (Respirable fraction)

Ammonium nitrate

Ammonium sulfamate (Respirable dust)

Ammonium sulfamate (Total dust)

Bismuth telluride, Se-Doped

OSHA

Bismuth telluride, Undoped (Respirable dust) OSHA

CIM

ID 188

ID 121

5 mg/m 3

15 mg/m

5 mg/m

15 mg/m 3 Bismuth telluride, Undoped (Total dust)

Boron oxide (Total dust)

OSHA

Boron oxide (Total dust) (Particulates, Total) NIOSH

CIM

ID 125G

0500

15 mg/m

10 mg/m

3.5 mg/m

3 Carbon black

Carbon black

Chromium, Metal & Insol cpds

NIOSH

OSHA

5000

ID 196

ID 121

ID 125

3.5 mg/m 3

1 mg/m 3

Chrysene OSHA

Coal dust (<than 5% SiO2)

Coal dust (>than 5% SiO2)

Coal tar pitch volatiles

Copper dust

Copper, Dusts & Mists

Copper (Elements)

Copper fume

Cotton dust (Raw)

OSHA

CIM

ID 142

2.4 mg/m 3

10 mg/m

0.2 mg/m

1 mg/m 3

NIOSH

OSHA

7029

ID 125G 1 mg/m 3

OSHA

NIOSH

OSHA

ID 121

7300

7029

ID 121

CIM

1 mg/m

0.1 mg/m

ID 125G 0.1 mg/m

1 mg/m 3

* Refer to Agency Method

Continued on next page

B - 1

NIOSH/OSHA Particulate Air Monitoring Reference,

Continued

Dust/Hazard

Crag herbicide (Respirable dust)

Crag herbicide (Total dust)

Cresol, All isomers

Cyanide (as Cn)

Fluorides (Aerosol & Gas)

Glass, Fibrous dust

Lithium (Elements)

Lithium hydride

Magnesium oxide fume (Total dust)

Manganese (Elements)

Manganese fume (as Mn)

Methoxychlor (Total Dust)

Oil mist (Mineral)

Oil mist (Vegetable) (see Dust, Total and

Respirable nuisance)

Pentaerythritol (Total dust)

Pentaerytritol (Respirable dust)

Agency Reference TWA

OSHA

NIOSH

OSHA

NIOSH

CIM

5(S356)

CIM

2546

5 mg/m 3

10 mg/m

15 mg/m

10 mg/m

OSHA

NIOSH

ID 120

7902

15 mg/m 3

5 mg/m 3

2.5 mg/m 3

STEL

OSHA CIM *

Glycerin mist (Particulates)

Glycerin mist (Respirable)

Glycerin mist (Total dust)

Grain dust (Oats, Wheat & Barely)

Graphite, Synthetic (Respirable dust)

Graphite, Synthetic (Total dust)

NIOSH

OSHA

0600

CIM

5 mg/m 3

15 mg/m

10 mg/m

5 mg/m 3

15 mg/m 3

Iodine (Particulates)

Kaolin (Respirable dust)

OSHA

ID 212

CIM

5 mg/m 3

15 mg/m 3

0.1

Kaolin (Total dust) OSHA CIM

Lead NIOSH

Lead (Elements)

Lead, Inorganic fumes & dusts (as Pb)

NIOSH

OSHA

7300

ID 121

<0.1 mg/m 3

0.05 mg/m 3

NIOSH

OSHA

7300

CIM

25 µg/m

15 mg/m

1 mg/m 3

3 OSHA

NIOSH

OSHA

ID 121

7300

ID 121

CIM

ID 128

15 mg/m 3

5 mg/m 3 mg/m

5 mg/m

ID 178SG 5 mg/m 3

OSHA

CIM

15 mg/m

5 mg/m 3

Continued on next page

B - 2

NIOSH/OSHA Particulate Air Monitoring Reference,

Continued

Dust/Hazard

Picloram (Tordon), Respirable dust

Picloram (Tordon), Total dust

Plaster of Paris (see Dust, Respirable nuisance)

Portland cement (Respirable dust)

Portland cement (Total dust)

Respirable nuisance

Respirable nuisance (Particulates)

Total nuisance

Total nuisance (Particulates)

Rouge (Respirable dust)

Rouge (Total dust)

Silica, Amorphous

Silica, Crystalline tripoli, Respirable dust

Silicon carbide (Respirable dust)

Silicon carbide (Total dust)

Agency Reference TWA

OSHA CIM 5 mg/m 3

OSHA

NIOSH

OSHA

NIOSH 0500

OSHA

CIM

ID 142

CIM

0600

CIM

ID 142

CIM

15 mg/m

OSHA CIM

5 mg/m 3

15 mg/m 3

5.0 mg/m 3

15 mg/m

10 mg/m

5 mg/m 3

15 mg/m

20 mppcf

0.05 mg/m 3

5 mg/m

15 mg/m

5 mg/m 3

15 mg/m

STEL

Silicon (Respirable dust)

Silicon (Total dust)

Soapstone (Respirable dust)

Soapstone (Total dust)

Wood dust (except Western red cedar)

Wood dust (Western red cedar)

OSHA

CIM

20 mppcf

6 mg/m 3

2.5 mg/m 3

Zinc bromide (see Dust, Total and Nuisance)

Zinc oxide dust (see Dust, Total &

Respirable)

OSHA CIM

Zinc oxide fume

Zinc stearate (Respirable dust)

Zinc stearate (Total dust)

Zirconium cpds (as Zr)

OSHA

ID 121

ID 125

ID 143

CIM

ID 121

ID 125

ID 121

5 mg/m

15 mg/m

5 mg/m 3

B - 3

Appendix C

Glossary of Terms

Term Definition/Standard

µm

ARD

Inhalable Dust

Particulates

Micron, 1/1000 of a meter.

Arizona Road Dust

Particulates having a 50% cut point at 100µm.

LPM mg/m 3

NIOSH

OSHA

Liters per minute.

Milligrams per cubic meter.

National Institute of Occupational Safety & Health

Occupational Safety & Health Administration.

Particulates having a 50% cut point at 3.5µm. Respirable Dust

Particulates

STEL Short-term exposure level. Maximum dust concentration over a 15-minute period.

Thoracic Particulates Particulates having a 50% cut point at 10µm.

TWA Time Weighted Average. Average particulate concentration over a period of time.

C - 1

Appendix D

EPAM-5000 Accessories

Overview

Introduction

Accessory and part number

Accessories may be purchased separately for the EPAM-5000.

Use the part number from the table below to order EPAM-5000 accessories.

110 V

220 V

47mm EPA FRM Sty b Cassette

Battery Pack

Span Reference

Cleaning Kit

Computer Interface Cable

Flow Meter

EPAM-5000 Media CD-Rom Includes: Computer

Software and Instruction Manual

1.0µm Particle Size Cut Point Impactor

2.5µm Particle Size Cut Point Impactor

10.0µm Particle Size Cut Point Impactor

Shoulder Strap

Impactor Sleeve

Strobe Light

Solar Panel

Subzero Heating Element

Remote Hand-held Sampling Probe

BC-105-110

BC-105-220

FH-105

BP-105

CS-105

KK-101

CC-102

FM-102

CD-105

EPAM-1.0

EPAM-2.5

EPAM-10.0

SS-101

IMS-105

SL-105

SP-105

HA-105

RSP-105

D - 1

Hello! I am an AI chatbot specifically trained to assist you with the SKC EPAM 5000 Environmental Particulate Air Monitor User's Guide. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you're looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant is out of keyboard. Please, try again later.

It looks like you''ve reached a document that is written in multiple languages, including one that isn''t your native language. You can use the following links to temporarily hide pages without the language you prefer.