User Manual


Add to my manuals
139 Pages

advertisement

User Manual | Manualzz

XNR44P 4 Channel NVR with PoE

User’s Manual | 2

Safety Information

Before You Begin

Read these instructions before installing or operating this product.

Note: This installation should be made by a qualified service person and should conform to local codes.

This manual provides installation and operation information. To use this document, you must have the following minimum qualifications:

A basic knowledge of CCTV systems and components

A basic knowledge of electrical wiring and low-voltage electrical connections

Intended use

Only use this product for its designated purpose; refer to the product specification and you documentation.

Customer Support

For assistance in installing, operating, maintaining and troubleshooting this product refer to this document and any other documentation provided. If you still have questions, please contact

Norbain Technical Support and Sales:

Norbain SD Ltd, 210 Wharfedale Road, IQ Winnersh, Wokingham, Berkshire RG41 5TP, England.

UK +44 (0) 118 912 5000

Note: You should be at the equipment and ready with details before calling Technical Support.

Conventions Used in this Manual

Boldface or button icons highlight command entries. The following warning, CAUTION and Note statements identify potential hazards that can occur if the equipment is not handled properly:

* Warning:

Improper use of this equipment can cause severe bodily injury or equipment damage.

** Caution:

Improper use of this equipment can cause equipment damage.

Note: Notes contain important information about a product or procedure.

This apparatus is manufactured to comply with the radio interference.

A Declaration of Conformity in accordance with the following EU standards has been made. The manufacturer declares that the product supplied with this document is compliant the provisions of the EMC Directive 2004/108/EC, the CE

Marking Directive 93/68 EEC and all associated amendments.

All lead-free products offered by the company comply with the requirements of the

European law on the Restriction of Hazardous Substances (RoHS) directive:

2011/65/EU, which means our manufacture processes and products are strictly

“lead-free” and without the hazardous substances cited in the directive.

3 | FULL HD Network Video Recorder

The crossed-out wheeled bin mark symbolizes that within the European Union the product must be collected separately at the product end-of-life. This applies to your product and any peripherals marked with this symbol. Do not dispose of these products as unsorted municipal waste.

* This symbol indicates electrical warnings and cautions.

** This symbol indicates general warnings and cautions.

NORBAIN SD LTD reserves the right to make changes to the product and specification of the product from time to time without prior notice.

WARNINGS AND CAUTIONS

:

To reduce the risk of fire or electric shock, do not insert any metallic objects through the ventilation grills or other openings on the equipment.

User’s Manual | 4

Contents

1 G

ETTING

S

TARTED

1.1

C

HECKING

S

UPPLIED

I

TEMS

1.2

S

YSTEM

S

TARTUP

2 E

XPLANATION FOR

E

ACH

F

UNCTION

2.1

F

RONT

P

ANEL

2.2

R

EAR

P

ANEL

3 O

PERATION

3.1

U

SER

L

OG

-

IN

3.2

Q

UICK

S

ETUP

3.3

L

IVE

D

ISPLAY

M

ODE

3.4

F

REEZE

M

ODE

3.5

R

EGISTRATION

3.6

I

NSTANT

R

ECORD

3.7

P

LAYBACK OF

R

ECORDED

V

IDEO

3.8

S

IMULTANEOUS

L

IVE AND

P

LAYBACK

(CAMEO)

3.9

Q

UICK

B

ACKUP DURING

L

IVE

& P

LAYBACK

3.10

S

EARCH

R

ECORDING

I

MAGE

3.11

DST S

ETTING AND

S

CREEN

S

AVER

4 S

ETTING

4.1

S

YSTEM

4.2

D

EVICE

4.3

R

ECORD

4.4

A

LARM

4.5

N

ETWORK

C

HAPTER

1 : XNR44P U

SER

M

ANUAL

20

21

22

23

28

30

31

40

43

45

49

13

17

17

19

8

8

9

10

10

10

11

11

12

5 | FULL HD Network Video Recorder

5 W

EB

S

URVEILLANCE

5.1

W

EB

L

OGIN

5.2

W

EB

C

ONFIGURATION

5.3

W

EB MONITORING

5.4

W

EB

P

LAYBACK

6 CMS USER G

UIDE

6.1

PC REQUIREMENT

6.2

INSTALL

6.3

UNINSTALL

6.4

BASIC OPERATION

6.5

CMS FUNCTIONS

6.6

CMS SETUP

7 MAC ACS U

SER

G

UIDE

7.1

S

YSTEM

R

EQUIREMENT

7.2

I

NSTALL

7.3

B

ASIC

O

PERATION

8 M

OBILE

P

HONE

S

OFTWARE

U

SER

G

UIDE

8.1

I

P

HONE APPLICATION SOFTWARE

8.2

A

NDROID APPLICATION SOFTWARE

8.3

U

SING

WAP+3G C

ONNECTION

9 A

PPENDIX

: D

YN

DNS S

ITE

R

EGISTRATION

10 A

PPENDIX

: S

PECIFICATION

61

65

66

77

86

94

94

94

54

54

55

57

59

61

61

96

106

106

118

128

131

136

User’s Manual | 6

Chapter 1

XNR44P U

SER

M

ANUAL

7 | Chapter 1 : NVR

User’s Manual | 8

1 G

ETTING

S

TARTED

1.1 Checking Supplied Items

Make sure that you have the following items supplied with your NVR. If any of these items are missing or damaged, notify your vendor immediately. Keep the packing utilities for moving or storage purposes afterwards.

Items Photo Quantity

User Manual

(NVR & Software)

Quick Start Guide

CD (Manual & Software)

Rubber Mount

12V 3A DC Adaptor

Power Cable

1 Set

1 Set

1 Set

1 Set (4 Pieces)

1 Set

48V 1.4A PoE Adaptor

Power Cable

USB Mouse

Option

1 Set

9 | Chapter 1 : NVR

1.2 System Startup

1.2.1 System Startup

After connecting peripheral devices such as cameras, monitors and a mouse to the NVR, power up the NVR by connecting

DC12V 3A adaptor to the power jack on the rear panel. The boot logo will display as shown below. Please wait until the boot process completes. Optional PoE needs independent power input of 48VDC.

Login with ‘User Name’ at the login window which will appear as shown below.

There is only one Administrator Account configurable in the NVR system. It is assigned with an unchangeable User ID marked as ‘admin’. The default password is empty (No Password). Administrator account has full access to the NVR and its configurable parameters. The Administrator Account also has the ability to create new users and to assign rights to the new user accounts. Those new users created by ‘admin’ account can also login with a specific password set by ‘admin’ account.

N

OTE

Do not forget the administrator’s password that was set for the first time. In case the password is lost, contact your vendor.

N

OTE

The mouse is included. In case you need to replace it, it is highly recommended to choose well-known major brands such as DELL, MICROSOFT, LOGITECH, or SAMSUNG.

2 E

XPLANATION FOR

E

ACH

F

UNCTION

2.1 Front Panel

[4CH (W)280x(H)48x(D)273mm]

User’s Manual | 10

No.

1

Items

LED Indicator

2 USB Port

2.2 Rear Panel

[4CH (W)280x(H)48x(D)273mm]

Functions

Indicate System Status

Power, Record, Network

USB Port (Ver. 2.0) for Mouse Operation, Backup Device or Firmware Update

No. I/O

1 PoE Power

2 Audio IN/OUT

3 ON/OFF

4 ALARM IN/OUT

5 USB

6 PoE

7 Ethernet

8 HDMI

9 e-SATA

10 DC12V

Functions

PoE Power Input (48V/1.4A)

Audio In/Out Port

Power ON/OFF Switch

Alarm Input/Output (1Relay output)

Mouse Input

PoE Camera Input

WAN Port

True HDMI Output e-SATA

Main Power Input (12V/3A)

N

OTE

Carefully check whether the specification of the peripheral devices match the NVR’s specification.

11 | Chapter 1 : NVR

3 O

PERATION

3.1 User Log-in

Check the power connection. The system can be used after power-on.

The NVR has various setting categories. The administrator can set the system password and <User> to prevent unauthorized changes to setting values and alteration of recorded file.

Enter the <Admin> or <User> password which has been set by using the virtual keyboard.

N

OTE

1) <LOGIN> window will be permanently displayed in monitor as above picture until a User logs in with the right ID and password. The default User ID is ‘admin’ and password is none (No password).

2) If it is set as Auto Log-In, NVR does not require LOG-IN. (Please refer to 4.1.2 User.)

3) Please be sure that the PoE Adapter should be connected to the NVR after the NVR is turned on so that the IP address can be allocated properly to NVR.

The “HELP” button will help you understand how to setup several important settings, even without the user’s manual book. For example, if you need help about how to set “Quick Setup”, click “HELP” button at the right bottom of the ‘Quick Setup’ menu.

User’s Manual | 12

3.2 Quick Setup

3.2.1 NVR Setup

Quick Setup is specially designed to enable easier & faster for the major NVR settings such as NVR network setup, IP camera search & registration. When the NVR boots up and login, the Quick Setup will be operated automatically. Quick Setup pop-up is controllerable in main menu. There are two ways for connecting to network setup: DHCP or Static IP.

The fatory default setting is as followings:

[WAN Port]

IP Address: 192.168.1.160

Subnet Mask: 255.255.255.0

Gateway: 192.168.1.1

[Local Port: Switch Setting]

IP Address: 10.10.1.1

Subnet Mask: 255.255.255.0

Gateway: 10.10.1.1

3.2.2 IP Camera Connection

When the IP cameras are connected to the NVR, you can search the connected cameras by clicking ‘Search’ button.

Once the cameras are discovered, check the box of each camera and click the ‘Add to Camera List’ button. Then the cameras will be shown in the list at the bottom. Click ‘Save’ button.

N

OTE

In case of requiring the User ID and Password for certain IP cameras for proper registration, please click the ‘Edit’ button. The User ID and Password for each IP camera should be the same one which are used for web configuration page of the camera.

13 | Chapter 1 : NVR

3.3 Live Display Mode

3.3.1 Full HD(1080p) Live Display

Full HD Live Display can be supported in live mode by using HDMI.

N

OTE

In playback mode, the maximum resolution is 1920*1080(main) and 640*360(secondary)

<Full HD Live & Playback Display>

3.3.2 Display

CH selection can be done by CH1, CH4 buttons and display mode can be changed by MODE button.

The live images can be displayed in 1, 4 screen mode. Whenever the left/right arrow button on the front panel, the screen will be sequentially changed.

[1 Ch] [4 Ch]

To select channel by mouse, click target channel to display in full screen live mode. Clicking the screen again is to return to previous display mode. Pop-up menu will be displayed by clicking right mouse button to select the display mode easily.

N

OTE

To properly select a channel using the mouse, you need to perform a slow and clear click of the left mouse button.

User’s Manual | 14

3.3.3 Icons Description

The live mode display’s icons or messages will be indicated on the screen to indicate the system mode or status.

Below is the icon categories that are indicated on the monitor.

Icon to be shown at Left-upper corner on each channel screen

Continuous Recording

Icon to be shown at Left-bottom corner on full screen.

Sequence display on

Motion Detection Recording

Sensor Activating Recording

Motion Detection + Sensor Activating

Recording

Instant Recording (Emergency Rec)

Digital zoom on

Audio Channel

Continuous Recording + Motion Recording

The sliding menu for display will be appeared when mouse cursor moves into bottom and right click of mouse enables to access a pop-up-menu.

means “Instant (emergency) recording”, which is useful to urgently start recording. In emergency recording, the system follows the instant record settings. The default settings for instant record are maximum performance recording of streaming from IP camera and applied for all channels.

You can click the right-forwarded arrow button to automatically playback the latest video clip.

means the HDD usage percentage by video recording. If it shows 60%, then 60% of HDD space has been used up for recording.

N

OTE

If u cannot find any coloured-mark in the top right corner of the live screen mode, then it means that the system does not record any image. In this case, you need to check recording schedule or camera of the main setup menu.

15 | Chapter 1 : NVR

3.3.4 Pop-up Menu

You can click the right button of the mouse to pop up a sub-menu as shown below.

When “SEQUENCE” is selected, sequentially changed.

icon is shown on the bottom left corner of the screen, and display screen will be

You can select the “ZOOM” on a sub-menu by clicking the right mouse button on a full screen mode. When digital zoom function is activated, icon will be shown and zoomed area will be displayed on the bottom left corner. You can

User’s Manual | 16 select “Zoom-In size(x1.5, x2, x2.5 or x3)” on zoom pop-up menu. After selecting, move a yellow box by using the mouse to drag in the desired area of the camera to zoom. In order to go back to live display mode, please click “Zoom-In size” again.

When a camera is disconnected, a warning sound may be generated depending on the system settings. You can set the warning sound from ‘Network Failure’ section on the System Alarm of the Alarm menu.

Admin level can set different level of authorization for each user. If a certain user is not allowed to view a certain live and playback channel, then no image appears on the display screen. To setup, move to System menu and click ‘User’.

The ‘User Add/Edit’ popup page will appear like the screenshot below when admin level clicks the button ‘Add’ at the right bottom. If Boxes are checked, The user can have an authorization to get access to each function and section.

3.3.5 Alarm Status

Intuitively, System alarm and Camera alarm will be displayed in icons. System alarm includes HDD S.M.A.R.T, Fan failure,

Disk Error and No Disk and Recording failure. Camera alarm displays network connection status, motion event and sensor event from connected cameras. However, motion and sensor from camera will only be displayed when network camera supports the motion and sensor.

[Alarm Deactivated] [Alarm Activated]

17 | Chapter 1 : NVR

3.4 Freeze Mode

Click the right button on the mouse and select the Freeze mode while viewing a live image. In the Freeze mode, the image pauses; the date/ time information does not; and the system clock continues running. Press FREEZE to pause the live view.

To resume the live view, press FREEZE again, or click the right button on the mouse and select the FREEZE again.

3.5 Registration

When you want to change the camera source, registration menu enables to search and to register connected network cameras easily. Click the right button on the mouse and select ‘Registration’ to move.

User’s Manual | 18

19 | Chapter 1 : NVR

3.6 Instant Record

In the case of emergency, you can enable Instant Record. Click the right button on the mouse and select ‘Instant Record’ and the icon will be appeared and changed to Red ( )

After clicking ‘Instant Rec’, the icon will be changed as picture below. Click ‘Instant Rec’ once again to escape.

User’s Manual | 20

3.7 Playback of Recorded Video

It is easy to use the USB mouse to playback recording files. The recorded files can be seen backwards or forwards. Press the rewind and fast-forward buttons, and the playback speed can be controlled in steps of 2, 4, 8, 16, 32 times, real time when playing backwards( ) or forwards( ).

You can also play ‘Frame by Frame’ by clicking the button

‘I-frame by frames per second(FPS)’.

You can click playback button

or and ‘Backward’ is only available for playing

to automatically play the latest video clip. It can be performed by pop-up menu.

The picture below shows the system playing back a video.

In playback screen, you can make various playback modes, such as an instant manual backup (archive), go to calendar search mode, change channel, and change screen modes. By clicking the left mouse button in the colored-time bar, you can jump to a different time in the recording. In addition, you can move the vertical search bar and release by dragging it back and forth to search the desired time in detail.

21 | Chapter 1 : NVR

3.8 Simultaneous Live and Playback (CAMEO)

1Channel playback can be displayed in live view mode simultaneously, so called ‘Cameo’ function. In live view mode, mouse-right click on the channel that is desired to playback and then select Cameo to activate this function.

You will see the blue frame on the CH1 screen when Cameo function is activated as shown below.

User’s Manual | 22

3.9 Quick Backup during Live & Playback

You can easily archive video while viewing the video during live and playback mode.

In live & playback mode, you can press right click of mouse and Backup menu will appear immediately. When desired back period is decided, set the start time and end time with target channels. When USB stick is scanned to save, file name is needed to be input. The password and backup viewer can be included if required.

23 | Chapter 1 : NVR

3.10 Search Recording Image

3.10.1 Date/Time Search

The user can select the date and time to search for a certain file within the recorded video.

In the calendar, dates in RED means that there is recorded video data. Click a desired date in Red. Then, the recorded data for the selected date will be shown.

Once the recorded video data of the selected date is shown, you can adjust the vertical search line to the time that you want to search by dragging a mouse. As the vertical line is moving back and forth, you will see “the Search time” clock is also changing. When the correct time is chosen, click Play to see the selected video data.

The colors of the time bar are different, depending on the recording mode.

User’s Manual | 24

No color

- NONE

“NONE” means no recording by setup of schedule and recording.

Red color

- Instant recording

In continuous recording mode, the system records all the time as set by “CAMERA”.

Yellow color

- Continuous recording

Green color

- Motion-detection recording

In this mode, the system records only when motion is detected

In addition, users can set motion-recording configuration that can be set in camera menu and/or network camera menu setting.

Orange color

- Sensor-activated recording

In sensor mode, the system will record when a sensor is triggered during the dwell time as set in

“SENSOR” of the “ALARM” menu. Sensor input can be selected between camera input sensor and

NVR input sensor. NVR input sensor is direct alarm input to NVR physically but Camera input sensor is triggered by network. You should verify if specific network camera is integrated with NVR to manufacturer.

Pink color

- Motion detection + Sensor-activated recording

The system does not record without motion and sensor event. Motion event data comes from network camera can be set in “Camera” in “DEVICE” menu. This menu is for integrated network camera setting and sensor type need to concluded in “Sensor” in “ALARM” menu.

If you set “OFF” in both “MOTION” and “SENSOR” in the “DEVICE” menu, then the system will neither record nor notify the Advanced Client Software or Central Management System.

Light Blue color

- Continuous + Motion recording

In this mode, the system records as continuous recording mode when no motion is detected.

However, if only motion is detected, system starts recording as motion recording mode.

When continuous recording mode, the system records in 1frame per second and when motion recording mode and the system will follow the camera setting value which you can set in record setup menu.

*Record Setup is available only for approved camera models.

25 | Chapter 1 : NVR

3.10.2 Event Log

The Event log search is used to find particular event, quickly and easily. Click the right button on the mouse as shown below and select the ‘Event Log’ to move. Click

USB memory device in text file format.

play icon to play back the selected event data. You can copy this event list to a

Once a USB memory stick is inserted into the USB port, then press “SCAN” button to detect the USB stick and then press

“EXPORT” to copy the log information to the media.

To sort particular events, you can select event type with time & date by a mouse or remote controller.

The following are the categories indicated on the Event Viewer.

1. Alarm by Sensor

2. Alarm by Motion

3. Alarm by Connection Failure

4. Alarm by Instant Record

5. Alarm by HDD Full

N

OTE

If the Alarm does not activate even though the alarm input setting has been made, check the alarm connection of the NVR rear panel and Network camera alarm.

User’s Manual | 26

3.10.3 System Log

The system log search can be used to find particular system log information, quickly and easily. You can copy this event list to

USB memory device in text file format. Click the right button on the mouse as shown below and select the ‘System Log’ to move.

Once export is completed, you will find a date folder created in USB thumb drive. There is “system.log” file stored in the date folder.

The following are the categories indicated on the system log viewer.

1. Log by system

2. Log by setup

27 | Chapter 1 : NVR

3. Log by network

N

OTE

20 numbers of log record will be shown on one page of the <System Log> and <Event Log> window. You can click the arrow icon to search the log records on another page.

3.10.4 First Data

Go to the first screen of the recorded video. This is the oldest video recorded.

3.10.5 Last Data

Go to the last screen of the recorded video. This is the latest video recorded.

3.10.6 Bookmark

Go to the bookmark list to search the recorded video data in the bookmark list. You can make their own bookmark list very simply by click button, during playback. When you do bookmark search, you can easily playback the bookmarked video data by clicking button, right next to each list. The bookmark will be available up to 32 times.

User’s Manual | 28

3.11 DST Setting and Screen Saver

DST starts at 2:00 local time on 2 nd

Sunday of March, and ends at 2:00 DST on 1 st

Sunday of November.

During DST (Daylight Saving Time) period, NVR time clock has to be adjusted according to regional time zone. That is, the

NVR time clock will be shifted by one hour after the DST settings start, and the NVR will restore the time clock back to normal after DST finishes.

To make DST setting on the NVR, go to the menu: SYSTEM > SYSTEM INFO and click “DATE/TIME” to get the DST setting window as shown below. You can setup DST “Begin & End” time after checking “USE DST” box.

Since the clock jumps from 2:00 to 3:00, when you go to search mode, you can clearly see there is no data in all channels for one hour due to DST.

DST ends at 2:00 DST, and the clock jumps backward to 1:00 standard time on 1 st

Sunday of November.

When DST finishes, there is an hour of overlapped video. The overlapped time video will be indicated in a blue color in the

Intelli-Search Bar during playback mode.

29 | Chapter 1 : NVR

When you click on such overlapped period, a message titled “Recorded video Selection” will pop up. Then you can then select whether to play DST data or Non-DST data.

Click OK to play DST image. Click CANCEL to play Non-DST image.

[“DST” image is displayed on screen] [“Non-DST” image is displayed on screen]

To make SCREEN SAVER setting on the NVR, go to the menu setup: SYSTEM > SYSTEM INFO and click “SCREEN

SAVER” to get the SCREEN SAVER setting window as shown below. You can select CRT and/or VGA by checking the boxes.

You can set the WAITING TIME for when the monitor will automatically turn off.

You can turn on the selected monitor by clicking a mouse, pressing any frontal key buttons, or pressing any buttons on the remote controller.

N

OTE

WAITING TIME: You can select the WAITING TIME from NONE, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 20, 30, 40, 50, and up to 60 MIN. The SCREEN SAVER will not work when either WAITING TIME is set to “NONE” or both

SPOT and VGA checkbox are unchecked. SCREEN SAVER may not work, during system upgrade, HDD format, or data backup process. The system continues to record while the monitor is turned off.

When it comes to the “AUTO LOGOFF” setting, please refer to the USER setting.

User’s Manual | 30

4 S

ETTING

General setting structure consists of “Quick Setup”, “System”, “Device”, “Record”, “Alarm,” and ‘Network” as shown below.

<QUICK SETUP> <SYSTEM> <DEVICE>

<RECORD> <ALARM> <NETWORK >

Main MENU Sub MENU

QUICK SETUP

SYSTEM

DEVICE

RECORD

ALARM

NETWORK

NVR

REGISTER

SYSTEM INFO

USER

EXPORT/IMPORT

HDD

BACKUP

MONITORING

FACTORY DEFAULT

REGISTER

CAMERA

AUDIO

SCHEDULE

RECORD SETUP

HOLIDAY

SENSOR

SYSTEM ALARM

MOTION ALARM

NOTIFICATION

NETWORK

DDNS

IP FILTER

31 | Chapter 1 : NVR

4.1 System

The system menu button is selected by clicking the right mouse button.

The sub-menu window will be displayed and you can choose specific menu by selection of sub-menu to set up and/or edit.

4.1.1 System Info

Use this sub-menu to check system information status or to change the system-related configuration.

You can then move to other sub-menu of the System; System Info, User, Export/Import, HDD, backup, monitoring and Factory

Default by moving mouse pointer or pressing the arrow buttons on the front panel.

Mac address is an unique network identification number for each system.

User’s Manual | 32

In “DATE/TIME SET,” you can activate DST (Daylight Saving Time). Select the time synchronization server and other basic settings like time zone/time format.

N

OTE

There are two types of TIME SYNC MODE.

1) NVR as NTP Sever mode

The operating NVR is set as a Time Sync Server, which can synchronize the time clock of another

NVR(s) connected over same network environment.

2) NVR as NTP Client Mode

The operating NVR is set as one of the client NVR(s). Input the IP No of designated NVR, Advanced

Client Software (ACS), or Central Management System (CMS), as a Time Sync Server in “SYNC

SERVER”; and then its time clock is synchronized with Time Sync Server by setup time in “SYNC

CYCLE”.

Upgrade: You can easily upgrade the system in “Upgrade” menu via USB/FTP server, upon the selection as shown below:

33 | Chapter 1 : NVR

P

ROCEDURE How to upgrade system firmware by using USB memory stick

1) Insert the USB thumb-drive formatted by FAT32 in any USB port of NVR (compatible with USB

2.0)

2) Once the system detects the thumb-drive, you can see its brand or model name in the

“DEVICE” field after pressing the “SCAN” button.

3) Click “OK” to confirm.

How to upgrade system firmware by using FTP server

1) Select FTP in the drop-down list and type a given IP address in the Host Address (FTP server IP address) field. User name and password is “none” (Default). *The FTP server address is subject to change without a prior notice.

2) Click ‘Check’ button then NVR will detect the latest Firmware version from the FTP server. If there is a new firmware, NVR will ask you whether you want to upgrade it or not.

3) Click ‘OK’ to confirm it and then click ‘START’ to start upgrading.

C

AUTION

It is recommended to format the HDD after finishing the firmware upgrade because the data recorded by previous firmware may cause malfunction of NVR due to different format.

It is possible to send the system firmware back to factory default. This may be useful if functionality takes a step backwards after a system upgrade. It is highly recommended to check all functions and menus after a firmware upgrade for proper layout and performance.

In “Display Setting”, you can set OSD information display in Live & Playback mode and Dwell time of set-up display, OSD and

Sequence.

Transparency is the transparency level of the menu screen. 0% means no transparency at all.

N

OTE

NVRs support the following video resolutions: 640x360, 1280x720, 1280x1024, 1920x1080

You must set the proper resolution according to the monitor resolution.

Default HDMI resolution is set to 1024x768. Depending on the resolution of monitor, it is recommended to change resolution to 1920x1080.

User’s Manual | 34

4.1.2 User

Master User of this system is always Admin with factory default of No password.

Admin must change the password of the NVR for extra security.

Admin can designate a new User with different permission levels by functions, menu access and live & playback.

“Function” is to authorize the User to control certain functions, like search, backup and playback.

“Menu Access” is to authorize the User to access certain menu settings, like system, camera, record, network, alarm and quick setup. “Live & Playback” is to restrict a User to see both live display and a playback video for a certain camera channel.

N

OTE

Total number of Users including administrator is 9.

You can change the setting, so the NVR does not require login or lock the NVR control. Click ‘Option’ button at the right bottom, then the ‘Option’ popup window appears.

If you select “On Boot” on the popup page, the NVR will not ask for an ID and Password input again even though the system reboots.

If you select Auto Log-off and sets the time, the NVR will automatically go to the live display mode that occurs after the set time. Then, the NVR will ask for an ID and Password input when you want to control the NVR.

35 | Chapter 1 : NVR

4.1.3 Export/Import

You can copy and paste the system configuration values in this menu. “Export” allows you to copy the settings for this system to USB memory devices. “Import” allows the you to recall the settings saved from other systems using USB memory devices.

During import process, make sure that the firmware version of source NVR is the same as the destination NVR.

4.1.4 HDD

Internal HDD information and External HDD information is displayed. External HDD information display is possible in approved e-SATA storage.

You can select “Overwrite” or “Rec Stop” when the HDD is full.

You can format a new HDD or an existing HDD for each drive. In order to format a HDD, check the checkbox and then click

“HDD Clear” button in the HDD menu.

The maximum number of built-in HDD units varies across NVR models.

User’s Manual | 36

On the NVR system, NVR Health Check is represented in % sign as shown below. It indicates the lifetime and the temperature in Celsius of the hard disk drive.

If system resources are occupied with task, such as making a network connection or performing video playback during the format process, the format may fail. If the format fails, reboot the system resources and then try to format again.

N

OTE

1) Formatting may take around 40 sec for 320GB, 1 minutes for 500GB, or 7 minutes for 2TB.

2) The system always reserves a maximum of 20GB of space in each built-in HDD to utilize the memory for archiving effectively.

37 | Chapter 1 : NVR

4.1.5 Backup

You can archive a video clip recorded for a certain period on a selected channel or channels as shown below.

Connect an appropriate USB memory device, like USB thumb drive, USB HDD and press the “SCAN” button to get the system to recognize it before archiving. Necessary file size will be shown before burning.

N

OTE

Backup device shall be a well-known major brand of USB thumb drives formatted by FAT/FAT32 for proper backup.

N

N

OTE

OTE

You can easily backup video in “Quick Backup” during video playback.

You can click the “Calculate” button to learn the backup file size before executing backup.

N

OTE

You can rename the backup file name before starting backup process and also put a password in the backup file for security purpose. In order to playback the file, you should input the password.

Backup Video Player

There will be a single file after archiving, if “Auto Player” was selected.

You can double click “Player.exe” file to open the video data file (PSF format) in the folder.

User’s Manual | 38

You can print out, capture a still image, zoom out, or make an ASF file format, by using the icons located on top of the player window.

N

OTE

You also can play the backup-video clips by Advanced Client Software and Central Management System.

39 | Chapter 1 : NVR

4.1.6 Monitoring

Monitoring menu enables you to see the status information.

Network status display receiving bandwidth from cameras and transmitting bandwidth to external access in graph. Property shows NVR network information and Client status displayed by external access through network. It keeps showing the time & date with IP address.

Connection log displays camera connection and disconnection history log. It includes channel, time & date, and IP address so that you can check the status with log.

4.1.7 Factory Default

With an authorized password, you can get the system back to factory default configuration.

N

OTE

Upon clicking “Start” button and entering the admin password, all the configuration values made by the user will be deleted. To proceed, select the boxes listed. The boxes that are chosen will be set to factory defaults. However, the recorded video data will not be deleted.

4.2 Device

There are Device sub-menu to set-up Register, Camera and Audio function.

User’s Manual | 40

4.2.1 Register

Network cameras should be registered in NVR to transmit the video streaming. Connected cameras can be found on a local network by clicking the ‘Search’ button. When camera are discovered, you can assign the discovered cameras o specific channels on the NVR by Add to Camera list . If an added camera channel needs to be changed, please use CH drop down menu and select desired channel.

You can search and register manually the cameras in WAN condition. Assign the channel, IP address, login ID, Password.

Most important information is RTST URL information from network cameras. If network cameras support more than dual stream, you are able to select the secondary stream.

4.2.2 Camera

You can setup camera title, covert, motion area. “Covert,” also called “hidden camera” feature. You can setup a camera on each channel by clicking Channel button ’01 ~ 04’.

41 | Chapter 1 : NVR

Motion Area Setup

The default motion area setup relies on network camera setting and direct control of network camera is supported for approved models. Choose the desired motion area by dragging a mouse using left button. The whole image or upto 4 individual areas of the image can be selected. To remove all selections made, click the right button on the mouse and choose

‘Clear All’.

Select also “Sensitivity” from ‘Lowest to Highest’.

Title

You can name the camera title.

Covert

“Covert,” also called ‘hidden camera’ feature, hides camera display and playback as if there were no camera recording. You can apply this covert function not only to Live view, but also to Playback view.

Brightness, Contrast, Hue

Adjusting brightness, contrast and hue to camera is available. When setting is done, click the ‘Apply’ button.

Advanced Setup

“Advanced Setup” can be supported by the approved camera only.

Network Type

Choose DHCP or Static IP. When choosing Static IP, IP address, Subnet Mask and Gateway will be activated.

IP Address / Subnet Mask / Gateway

Type the IP Address, Subnet Mask and Gateway.

User’s Manual | 42

Mac Address

Mac Address of the IP camera is not activated.

Auto Iris

Adjusting to the light of screen automatically responding to external Illuminance variation. Not activated.

Flicker

Available to set to Off, 50Hz or 60Hz.

BLC

Back Light Of Compensation. Available to set to On or Off.

WDR

Wide Dynamic Range. Available to set to On or Off.

AWB

Auto White Balance. Available to set to In-Door, Out-Door or Manually setting.

4.2.3 Audio

You can select NVR Input Audio and channel can accept only one of each audio input.

43 | Chapter 1 : NVR

4.3 Record

You can configure various record settings such as Continuous, Motion, and Sensor for each individual camera channel in the

Record Setup Menu. Network Stream settings relies on network camera for recording. Approved network camera setting will be set by NVR menu and you can set up streaming video quality, FPS, bitrates in network camera menu as well.

4.3.1 Schedule

You can set up the record schedule by applying various record modes to each date and time. Simply select a record mode by ticking the appropriate box then click and drag over the desired date and time. In a mode of Continuous and Motion, the NVR records data at a rate of 1Frame Per Second(FPS) before the motion occurs(C) and when the motion occurs(M), it records at the setting in the record setup.

4.3.2 Record Setup

You can set the streaming setup of network camera to record. Main stream record is possible up to 1920*1080 and secondary stream is up to 640*360 with adjustable FPS, Quality, Pre Alarm and Post Alarm.

User’s Manual | 44

Channel

Select channel to set the registered network camera

Resolution

Select resolution up to 1920*1080(Full HD) for main stream and 640*360 for secondary stream.

Bit Rate type

Select between CBR(Constant Bit Rate) and VBR(Variable Bit Rate)

Quality

Select the desired Quality level(Lowest/Low/Normal/High/Highest)

FPS

Select desired FPS(Frame per Second) to record up to 30fps.

Pre/Post Alarm

Select desired Pre Alarm time within 5 seconds and Post Alarm time within 15 seconds.

N

OTE

Due to system performance, Bitrates per channel must be limited to 4,000kbps/CH for Main Stream and 512Kbps/CH for Secondary Stream.

4.3.3 Holiday

You can setup a specific day of a month or day of week as holiday as shown below. Once the holiday is selected, the recording setup for those holidays will be affected by the schedule setting in the schedule.

45 | Chapter 1 : NVR

4.4 Alarm

4.4.1 Sensor

You can select the sensor input between NVR and supported network cameras. Mapping is only available for either of

Network camera sensor or the local sensor of NVR on the same channel.

Type

OFF, N/O (Normal Open), N/C (Normal Close)

Cam

Select the associated camera channel.

Notify

You can select how to be alerted when a sensor is activated by pressing the “NOTIFY” button. The system can generate a buzzer sound and/or make a pop-up screen for the camera in alarm.

C

AUTION

Relay contact can handle up to 24VDC/1A(or 125VAC/0.5A) of other devices. If connected to a circuit that is over 24VDC/1A(or 125VAC/0.5A), the system may experience problems.

User’s Manual | 46

Relay

Off / Relay Output to trigger other device.

Dwell Time

Set the recording period from the start of sensor input activation. During this period, the corresponding camera video will record according to the frame and alarm (relay) output set. The recording stops and alarm output is turned off when the dwell time has elapsed.

N

OTE

“Sensor” here means the alarm connected to the NVR, which is triggered by physical sensor input or transmitted data from network camera sensor input

N

OTE

If the sensor does not operate properly, check the setting of the sensor type (N/O or N/C). The alarm might not function if the actual connecting sensor type and the sensor type in the system setting are inconsistent.

N

OTE

There are tree options to choose from the notify of Camera Input Sensor – All, Beep and Cam pop-up.

“Beep”

means that beep sounds automatically when an alarm is triggered.

“Cam pop-up”

means that multi-screen live video mode will be switched automatically to single channel mode, when an alarm is triggered. This single channel video will be the channel triggered by alarm.

“All”

means that using “Beep” and “Cam pop-up” simultaneously when an alarm is triggered.

4.4.2 System Alarm

S.M.A.R.T. alarm is an alarm signal triggered when the HDD is about to be out of operation.

Connection Failure. Alarm is activated when camera is disconnected.

Recording failure. Alarm is triggered when NVR doesn’t record normally.

Fan Failure. Alarm is triggered when internal fan is stopped.

47 | Chapter 1 : NVR

You also set the percentage for HDD Usage. For example, when Usage is 50%, NVR will notify by a camera popup or a beep sound when HDD is 50%.

4.4.3 Motion Alarm

Select Motion alarm to record only when motion detection is triggered by NVR S/W upon you defined motion area.

An alarm signal is sent via the selected sensor-out channel.

COPY SETTINGS

Upon pressing Copy Settings button, Copy Settings popup will appear. In this popup, choose the camera you want to copy at the “From” field. Choose the parameters such as Use, Notify, Relay, and Dwell Time on the check box. Check on the checkbox next to the sensor numbers to apply the copy setting(s) to another channel on the “To” box.

N

OTE

“Motion Alarm” here means alarm triggered by motion detection set by motion menu of Network Camera.

4.4.4 Notification

Remote Notify

The system can notify an alarm message to the IP address of Advanced Client Software over the network.

You can choose from a selection of different kinds of alarms by pressing “ADD.” Alarms can be generated by Sensor, Motion

Detection, Disk Full, Admin PW Changed, Video Loss, and Power On/Off.

User’s Manual | 48

E-Mail Notify

The system can send notification to an Email address or Advanced Client Software and the Central Management System over the network. You can choose from a selection of different kinds of alarms by pressing “ADD.” Alarms can be generated by Sensor, Motion Detection, Disk Full, Admin PW Changed, Video Loss, and Power On/Off. By clicking “Use TLS”, you can use a public email address such as Yahoo, Google, Hotmail accounts. Type NVR name in the “NVR Name” box. The NVR name will appear in the email so that you can recognize which NVR sent an email.

N

OTE

Configuration’s first priority is always given to “Schedule Setup” of the “RECORD” menu.

Thus, the system will not send alarm message or email notification upon motion alarm or sensor even though you tick the checkbox of above event selection, unless you set the “Schedule Setup” in the

“RECORD” menu.

For example, if you set “Continuous” only for “Schedule Setup” of the “RECORD” menu and marks the

“All” checkbox in “REMOTE NOTIFY”, then the system will not send alarm messages. In this case, you have to set “C + M”, “MOTION”, “SENSOR” or “C+ S” for REMOTE NOTIFY or E-Mail NOTIFY to function properly.

49 | Chapter 1 : NVR

4.5 Network

4.5.1 Network

The system has built-in web server.

Internet Protocol Version

Not selectable. TCP / IP v4 support only.

Network Type

Select network connect type. Select either LAN for fixed (Static) IP or DHCP for dynamic IP.

If DHCP is selected, click ‘IP DETECT’ button to detect IP address information.

Subnet Mask

Subnet Mask address classifies the subnet that the system belongs to. Standard address is 255.255.255.0. For more information, please consult your network administrator or your internet service provider

Gateway

This is the IP address of the network router or gateway server. It is required when you want to connect through the external router from the remote. For more information, please consult your network administrator or your internet service provider

User’s Manual | 50

DNS Server

Enter the IP address of the Domain Name Server. There are two DNS settings. (The preferred DNS and the alternative DNS)

*You should enter the DNS Server information in order to use internet. (Provided by your ISP)

Switch Setting

When PoE option is applied, you can put the camera into PoE port directly. The network setting for PoE port will be designed independently. This IP range should not be the same range of NVR IP address.

TCP/IP Port

Enter the port number to use when connecting locally or remotely.

Web Port

Enter the port number to use when connecting from the Web Browser.

N

OTE

TCP/IP Port, Web Port should be a different number from each other.

UPnP (Universal Plug and Play) and Auto Private IP Setup (NAT Traversal)

UPnP stands for Universal Plug and Play, which is a relatively new technology that indicates a universal protocol for widespread plug-and-play devices to ease the network implementation. When a PC and a NVR both installed the UPnP function, the PC can automatically recognize the NVR in the same local area network. The advantage of this function is that a

PC can connect to the NVR directly by clicking on the icon representing the NVR in <My Network Places> folder as shown below. The first five characters of the file name of a detected NVR is subject to a firmware version

Simply double click on the desired icon. Then, it will open an internet browser that connects to the NVR via the remote control software as shown below. Please type in your User ID and Password to login and click ‘Connect’ button to connect.

51 | Chapter 1 : NVR

Auto Private IP Setup (NAT Traversal)

The UPnP NAT Traversal function will help to automatically setup a router if the NVR connects to the internet via a router.

When a PC connects to a NVR, which is not in the same local area network, a real IPO address and corresponding port number is required. However if the NVR is behind a router, the communication between the PC and the NVR will be transmitted back and forth by the router. The router will need to setup port mapping (Port Forwarding) before images from the

NVR is remotely viewed on the PC. For each individual NVR, the setting needs to be done individually.

If the NVR has UPnP NAT traversal function, the setting of the router will be done automatically when it is enabled.

Just check ‘Auto IP (NAT Traversal)’ check box in the UPnP setup menu. Then it will take care of Auto IP detect by itself.

N

OTE

The system transfers video images at real-time over the network even during no record.

For example, you can monitor live video even when motion has not occurred during motion detection mode.

N

OTE

If there is no physical network connection, it may take a few minutes for the system to start working, since the network configuration in DHCP mode and the DHCP connection cannot be made.

4.5.2 DDNS

You have to tick the “Use DDNS” check box to use it.

DDNS Server

joinip.net or joinip2.net is the fixed domain name of DDNS server.

You cannot change the DDNS name.

User’s Manual | 52

N

OTE

The standard(default) DDNS domain name is joinip2.net, and you can use joinip.net or dyndns.com by drop-down list.

4.5.3 IP Filter

You can block and allow the specific IP addresses to manage. Check the box ‘Use IP Filter’ first to allow some specific IP addresses to use. The default is 0.0.0.0 / 0.

Select ‘Edit’ to input the desired IP address range. When registered setting is needed to be changed, you can select ‘Edit’ or

‘Delete’.

53 | Chapter 1 : NVR

4.5.4 System Shutdown and change password

The system can be power off by ‘Shut Down’ button. The ‘Shut Down’ can be done by clicking a right button of mouse.

The default password for ‘admin’ account is none. Therefore, just click ‘OK’ button on the popup window. If you change the password for ‘admin’ account, please type in the changed password to login.

N

OTE

You can type in the password using the virtual keyboard through a mouse.

User’s Manual | 54

5 W

EB

S

URVEILLANCE

The system has a built-in web server.

Using an ordinary web-browser over a network, you can always stay connected to the system for live monitoring, playback, or remote configuration without installing the Advanced Client Software (ACS).

5.1 Web Login

You need to input the correct IP address in the web browser after making the web port available in the router.

After allowing the download of the Active-X file, The login page view seen below. Default User ID is “admin” and No password.

55 | Chapter 1 : NVR

5.2 Web Configuration

Menu of Web Configuration

Main Classification

QUICK SETUP

SYSTEM

DEVICE

RECORD

ALARM

NETWORK

Sub Classification

NVR

REGISTER

SYSTEM INFO.

USER

HDD

DEFAULT

REGISTER

CAMERA

AUDIO

RECORD SETUP

SCHEDULE

SENSOR

SYSTEM

MOTION

NOTIFICATION

NETWORK

DDNS

IP FILTER

After logging in with the right ID and password, you can make various configuration changes in the Web Configuration window seen below. This Web Configuration menu is only available to the “admin” account.

[System] [Device]

User’s Manual | 56

[Record]

[Network]

[Quick Setup]

N

OTE

This NVR system has its own built-in web server.

This web CGI screen is directly supported from the built-in web server in the NVR, regardless of Internet connection.

57 | Chapter 1 : NVR

5.3 Web monitoring

You have to download Active-X file from NVR and install it at workstation PC before monitoring live video.

[Web Active X Install ]

You can get into web monitoring after log in as shown below. In order to connect to NVR, you have to click

“ Connect ” button which is located at the top left corner.

User’s Manual | 58

You can monitor live video in 1, 4, 9 or 16 screen modes. If you want to see single channel in full screen, you can double-click on the left mouse button when the cursor is positioned on the live video screen. You can change to single mode by clicking the mode icon located at the bottom left.

N

OTE

The image resolution in “Live monitoring” in this web browser is directly transferred from NVR

( Live image over the web browser depends on the Live Stream value on Record mode of NVR )

N

OTE

If live image is not properly shown on IE web browser due to network traffic jam or narrow bandwidth, it is recommended to close and re-open the IE web browser.

59 | Chapter 1 : NVR

5.4 Web Playback

You can remotely playback the NVR images by clicking “SEARCH” button in the middle of bottom window. In order to connect to NVR, the you have to click “ Connect ” button which is located at the top left corner.

Playback Time

Select the date and time on Time Search, located at the middle of left side of window, and click

Playback Icon

Play/Pause is toggled and playback speed is shown on the left box.

Play DST

Check this box to play overlapped images during DST (Daylight Saving Time) period.

For further details, please refer to Section 3.7 (DST Setting and Image Playback).

button.

Search Bar

You can move the blue vertical line to the time that you want to search.

The colours of the time bar are different by each recording mode. Please, refer to Section 4.3.2 for details on colour.

User’s Manual | 60

Chapter 2

CMS C

LIENT

S

OFTWARE

USER M

ANUAL

61 | Chapter 1 : NVR

6 CMS USER G

UIDE

6.1 PC REQUIREMENT

OS

CPU

VGA

RAM

HDD

OS

CPU

VGA

RAM

HDD

Recommended PC Requirement

Windows 7, 8

Intel Core i7

ATI Radeon HD 1GB RAM

8GB

100MB Free space

Minimum PC Requirement

Windows 7, 8

Intel Core i5

ATI Radeon HD 512MB RAM

4GB

20MB Free space

6.2 INSTALL

Run Central Management Software Setup.exe saved on the included CD.

When clicked, the Setup Menu will appear.

Press if you want to install the program in a different directory.

User’s Manual | 62

Press to move to the next screen.

Press to move to the next screen.

63 | Chapter 1 : NVR

Press to move to the next screen.

Click to begin installation. When the installation is complete, the following message will be appeared.

User’s Manual | 64

65 | Chapter 1 : NVR

6.3 UNINSTALL

To uninstall CMS, press UNINSTALL CMS from Start Menu of your PC.

A window will appear in Windows7 or Windows Vista. Press YES to begin the process. The following window will appear.

When the process is complete, the below message will appear.

6.4 BASIC OPERATION

Click on CMS icon on Desktop or click START on Windows PC and go to CMS Folder.

User’s Manual | 66

6.4.1 LOG IN

The default ID is Administrator, and there is no default password so please leave it blank. The administrator account has the highest level of authority on the CMS.

67 | Chapter 1 : NVR

6.4.2 SCREEN LAYOUT

User’s Manual | 68

7

8

9

10

4

5

No

1

2

3

6

Item

Main Toolbar

(Setup Tab)

Main Toolbar

(Export Tab)

Main Toolbar

(Main Tab)

Site List Panel

PTZ Panel

Description

The Main Toolbar has three (3) selectable tabs named "Main", "Export" and

"Setup". In the Setup tab, there are CMS setup and Remote setup.

In the Export tab, able to save JPEG, AVI and Print the images.

In the Main tab, able to connect Live and Search, disconnect, change display mode and sequence, Panorama Search and Thumbnail Search.

All of the registered sites in the setup tab are shown in the site list. Simply drag and drop the desired site to the display screen to connect to the site.

PTZ camera control is not available on the NVR system.

Search Panel

In the Search mode, the recording information per each channel will be displayed, when a specific date is selected in the calendar.

Display Panel

Event Search Panel

Information Panel

Favorite Panel

This is the area where live view and search view are displayed.

CMS also can receive all of events from DEVICE, and they are listed in this panel. An event data can be searched by double-clicking on an event.

Shows the current time and site information of the selected channel.

Create favorite site for quick access to the sites frequently viewed.

6.4.3 MAIN TOOLBAR (SETUP)

2

3

No

1

Item

CMS Setup

Remote Setup

Windows Exit

Description

Register sites, setup for user authority, and setup other CMS properties.

Access the setup menu of DEVICE remotely and change the settings.

Minimize/Maximize the CMS Window or close the CMS program.

69 | Chapter 1 : NVR

6.4.4 MAIN TOOLBAR (EXPORT)

3

4

No

1

2

Item

Image

Movie

Print

Windows Exit

Description

Capture the image of the selected (focused) channel.

Save the selected channel in ASF format movie file.

Print the selected channel.

Minimize/Maximize the CMS Window or close the CMS program.

6.4.5 MAIN TOOLBAR (MAIN)

9

10

11

6

7

8

No

1

2

3

4

5

Item

Live

Search

Disconnect

Disconnect All

Display Mode

Full

Sequence

Dual Monitor

Panorama

Thumbnails

Windows Exit

Description

Connect to the selected site in the site list in Live mode.

Connect to the selected site in the site list in Search mode.

Disconnect the selected single channel.

Disconnect all of the connected sites and channels.

Change the display mode in single, 4 split, 9 split, 16 split, 20 split, 36 split, 64 split.

Shows Full screen display.

Sequences the different channel displays.

Create an additional display window.

Able to show frame by frame display for a selected single channel in Search mode.

Thumbnail search for a selected single channel in Search mode.

Minimize/Maximize the CMS Window or close the CMS program.

User’s Manual | 70

71 | Chapter 1 : NVR

6.4.6 SITE LIST

The Site List displays all of the DEVICE that are currently setup for remote connection with the CMS application, and its cameras are available for view.

From the Site List Panel, select the desired camera and drag it on to the viewing area. Then, select the options Live or

Search ( ).

If an DEVICE site is dragged onto the viewable area, then the selected DEVICE or all cameras from the DEVICE will display.

User’s Manual | 72

6.4.7 SEARCH

The Search panel is activated only in Search mode.

When you connect to a site in Search mode, the date is highlighted in Red colour in the calendar, if the recorded data exist.

Select a specific date in the calendar and then recording information will be shown in the table.

(Go button) should be pressed to start playback from the selected time.

If DST is enabled, the earlier one-hour overlapped video will be shown first.

Each record mode is similar to below.

No Record White

Continuous (Yellow Color)

Instant (Red Color)

Alarm (Orange Color)

Motion (Green Color)

Click the time or move the time bar to the time you want to playback in the search panel.

For a more detailed search like below, double-click the time that you want to jump into.

Detailed search is available on a 6 minute basis like below.

73 | Chapter 1 : NVR

Playback Control Panel

No.

1

2

3

4

5

6

7

8

9

Button Description

Go to First.

Forward Playback : Decrease the speed / Reverse Playback : Increase the speed.

Step Forward.

Reverse Playback.

Pause.

Forward Playback.

Step Backward.

Forward Playback : Increase the speed / Reverse Playback : Decrease the speed.

Go to Last.

Audio control

Audio On/Off: Turn On or Off for Audio channel.

Two-way Audio: Two-Audio between CMS and DEVICE.

Bookmark: Bookmark the selected channel to the bookmark list.

User’s Manual | 74

6.4.8 DISPLAY

In live mode, the text LIVE will be displayed in white, and the channel will be bordered in blue.

In search mode, the text SEARCH will be displayed in red, and the channel will be bordered in red.

The selected channel will be bordered in yellow. The site name will be shown at the lower left hand corner of the screen.

75 | Chapter 1 : NVR

6.4.9 EVENT SEARCH

CMS can receive any event data from the DEVICE as shown below.

You can select a desired date to view the event list of the selected date.

You can choose either event log or system log.

Start the playback by double-clicking the Index number of each even list.

System log shows CMS start/end, live/search, option, remote setup, image/movie export etc.

User’s Manual | 76

6.4.10 INFORMATION

The current date/time, site name, IP address, ID, channel and Live/Search status will be shown.

6.4.11 FAVORITE

Cameras currently displayed on the screen can be added, deleted and edited as a favorite site group.

Place cameras of DEVICE site into a desired channel location of the screen and then click to create a new favorite site group. Then, you can simply place those cameras on the same channel location by drag & drop as shown below. In order to delete the favorite site, click to delete it.

77 | Chapter 1 : NVR

6.5 CMS FUNCTIONS

6.5.1 EVENT SEARCH

When you right click on a site in the site list, the quick access menu will be shown.

Select EVENT SEARCH to run Event Search.

3

4

5

6

7

No

1

2

Item

System Connection Info

Event Download Status

Calendar Search

Interval Setup

Event List

Channel/Event Filter

Start/Stop Search

Description

Input the information of DEVICE to connect.

Right after connecting to DEVICE, event information will be downloaded automatically. The download progress bar will be shown.

If there is an event in the selected date, the date is highlighted. Select a specific date to start event search.

Set the interval for event search.

The desired date is chosen, the event list of the desired date will be shown on the list.

Event information can be sorted by a channel or event type..

Start/Stop Search button.

6.5.2 REMOTE BACKUP

When you right click on a site in the site list, the quick access menu will be shown.

Select REMOTE BACKUP to run Remote Backup.

User’s Manual | 78

2

3

4

5

6

7

No

1

Item

System Connection Info

Recording Directory

System Recording Info

Backup Setting

Channel

Backup Progress

Backup Status Window

Description

Input the information of DEVICE to connect.

Decide the recording directory to backup.

Displays the start and end time of the recorded data in the system.

Setup the start and end time of the data to backup.

Select the channel to backup..

Backup Progress bar indicates the backup process status.

Displays the backup status in text message.

When the backup process is completed, “Backup Completed” message will appear.

79 | Chapter 1 : NVR

6.5.3 FIRMWARE UPGRADE

When you right click on a site in the site list, the quick access menu will be shown.

Select FIRMWARE UPGRADE to run Firmware Upgrade.

User’s Manual | 80

4

5

6

No

1

2

3

Item

DEVICE Connection Info

Firmware File Directory

DEVICE Name/

Current Version

New Version to upgrade

Upgrade Progress

Upgrade Status Window

Description

Input the information of DEVICE to connect.

Decide the firmware file directory to upgrade.

Displays the current DEVICE Name and Firmware Version.

Displays the new DEVICE Name and Firmware Version.

Start Upgrade and upgrade progress bar shows the upgrade progress status.

Displays the upgrade status in text message.

When the backup process is completed, “Backup Completed” message will appear.

81 | Chapter 1 : NVR

6.5.4 MULTI MONITOR

Click MULTI MONITOR in the Main Toolbar to run the Multi Monitor function.

When you click MULTI MONITOR, you will see another separate window with the same split display as the main window.

6.5.5 PANORAMA

Click PANORAMA in the main tool bar to run Panorama View.

In Live mode or Search mode, the panorama shows frame by frame display of the selected single channel.

To return to normal view, click PANORAMA again.

User’s Manual | 82

83 | Chapter 1 : NVR

6.5.6 THUMBNAIL SEARCH

Click THUMBNAIL in the main toolbar to run Thumbnail Search. This feature is only available in Search mode.

First select a channel and click THUMBNAIL; then, you will see the Thumbnail Search window as shown below.

3

4

5

6

No

1

2

Item

Date

Time Interval

Image Size

Time Range

Thumbnail images

Search

Description

Use the Calendar to select a desired date.

Select the Interval (time interval) which displays still shots by a specified time. You may choose 1min, 3min, 5min, 10min, 30min, and 1hour (ex. 1min. means 1 still shot per 1 minute of recorded video data.)

Adjust the Thumbnail Image size by using the slide bar. Moving the slide bar to the right will increase the image size, and moving it to the left will decrease image size.

Select the Time range (start time and end time) by using the slide bar.

Thumbnail images will be shown.

Search button.

If you click each thumbnail image, you can search the selected data directly.

User’s Manual | 84

6.5.7 BOOKMARK

Click icon to bookmark the selected one channel search data.

Once the selected search data is bookmarked, the bookmark data is listed with an image in the bookmark list as shown below.

Select a bookmark list and click search or double click the bookmark list to search the bookmarked data.

Click REMOVE button to remove a selected bookmark list and click DELETE ALL to delete all of bookmark list.

Click RENAME to rename the selected bookmark list.

6.5.8 DIGITAL ZOOM IN/OUT

In Live/Search mode, digital zoom can be activated in a single full screen mode by using a mouse wheel.

Scroll up the mouse wheel, and then you can zoom in. Scroll down the mouse wheel, and then you can zoom out the selected channel.

85 | Chapter 1 : NVR

6.5.9 Switch Stream

You can switch the Main stream to Secondary stream or vise versa on the site of a selected channel.

6.6 CMS SETUP

There are options for DEVICE Registration, Network, User, Display, Event and Misc.

6.6.1 NVR REGISTRATION

Add, Edit, Import, Export or Remove DEVICE site information.

User’s Manual | 86

Ex) Adding a new device site

In order to add a NVR, click ‘Add’ button, and put right information.

NVR can be detected by ‘Search’ button. Then the IP information will be received automatically.

No

3

4

5

1

2

6

7

8

9

10

11

Item

Name

IP

The name of the site.

IP Address.

Description

Search

Port

Web port

Search the DEVICE sites in the same local network. (UPnP function)

Port of the site. (Default: 9010)

Web Port of the site. (Default: 80)

User ID of the site. ID

Password

Channel

Model

Aspect Ratio

Password of the site.

Number of channel of the site.

(for example: 16ch DEVICE: 1-16 or specifically: 1,3,5,7,9)

Select a DEVICE or DEVICE’s model name.

Select the displayed Aspect Ratio.

(Custom, 1:1, 4:3, 16:9)

Secondary Stream Connect to the Secondary stream of NVR

87 | Chapter 1 : NVR

To edit and/ or remove DEVICE information, click ADD or REMOVE to amend DEVICE site information.

Able to export the current site list and save as a file or import the file to the site list.

Once the new DEVICE site is added, the new DEVICE information will be displayed at DEVICE site panel as shown below.

6.6.2 NETWORK

Able to setup RECONNECT and AUTO CONNECT in this tab.

Enable Reconnect:

When the network is unstable or disconnected, it will try to reconnect periodically. When the network gets stable again, it’s reconnected.

User’s Manual | 88

Enable Auto Connect:

When you restart the CMS program again, after CMS is closed, it will reconnect to the sites just as before.

89 | Chapter 1 : NVR

6.6.3 USER

User authority can be changed by Administrator. “admin” is the built-in account for administrating the DEVICE and CMS program.

Ex) User authority change

User authority can be changed by Administrator. ID cannot be changed but should be removed.

6.6.4 DISPLAY

Options for OSD setting.

Title: Able to turn on/off the DEVICE title with the channel number.

Date/Time: Able to turn on/off the Date/Time of the site.

DEVICE Name: Able to turn on/off the name of the site.

Time Format Sync: Synchronize the DEVICE time format to CMS.

Record Status: Able to turn on/off the Record Status of the site.

Live/Search: Able to turn on/off the Live/Search of the site.

Sequence: Able to set Sequence interval.

User’s Manual | 90

91 | Chapter 1 : NVR

6.6.5 EVENT

Setup the event port, event type and popup settings for event.

2

3

No

1

Item

Port

Filter

Description

Input the same event port number of DEVICE setting to receive event notification from the

DEVICE.

Select the type of event to receive.

Action Setup the popup duration and enable beep sound.

6.6.6 MISC.

Setup the Recording Directory, Language, Auto Upgrade, and Auto Login.

User’s Manual | 92

No

1

2

3

4

Item

Recording Directory

Language

FTP Information

Auto Login

Description

Decide the recording directory to save images and moving images.

Select a desired language.

In order to have Auto Upgrade, input FTP information. Once the FTP setup is done, CMS will detect the latest firmware is in the FTP and start upgrading automatically.

If you enable the auto login after inputting ID and Password, next time when you login, you don’t need to type in the ID and Password again.

93 | Chapter 1 : NVR

Chapter 3

MAC ACS C

LIENT

S

OFTWARE

U

SER

M

ANUAL

User’s Manual | 94

7 MAC ACS U

SER

G

UIDE

7.1 System Requirement

OS

CPU

VGA

RAM

HDD

OS

CPU

VGA

RAM

HDD

7.2 Install

Recommended System Requirement

Mac OS X 10.6(snow leopard)

Intel i5 CPU or upper

Recommended More than 256MB

Recommended More than 1GB

20MB Free Space

Minimum System Requirement.

Mac OS X 10.5( Leopard)

Built-in Intel CPU MAC

128MB

512MB

20 MB Free space a. Run MAC ACS.pkg on CD, and a Setup Menu appears as below.

95 | Chapter 1 : NVR

b. Select the HDD to be installed. Press the [Continue] button to move to the next screen. c. Press the [Continue] button to move to the next screen d. Press the [Install] button to Install MAC ACS.

User’s Manual | 96 e. Put in the password and Click [OK] to begin installation. When the installation is complete, the message appears as below.

7.3 Basic Operation

Click on ACS icon on Application Folder

97 | Chapter 1 : NVR

7.3.1 Screen Layout

User’s Manual | 98

No.

1

2

3

4

5

6

7

Item

Main Toolbar

NVR List Panel

Description

AVS Setting, Live and Search Connect, Disconnect, Image Save, Screen

Mode and Change

Registered NVR Site List. Possible to connect by Dragging

Live or Search

Connect Panel

PTZ Panel

Click Live or Search mode to connect the panel

PTZ camera control is not available.

Calendar Panel

Search by Time and Date

Search Panel Recorded information is shown in search mode.

Control the speed of Playback and Audio as well

Display Panel Transmitted Camera images are shown( Live and Playback )

99 | Chapter 1 : NVR

7.3.2 Main Toolbar

5

6

3

4

7

8

No.

1

2

Button

Site Manager

Print

Description

Register or Delete NVR on the list

Connect Connect to a site that is listed on the NVR list panel

(Select Live and Search mode at Connect Mode Panel)

Disconnect

Disconnect a selected channel

Disconnect All

Disconnect All Channels

Print out still image

JPG Export

Save a selected image to the desktop as JPEG format

Movie Export

Save a selected video clip to the desktop as mov format

Split

Single Channel, 4-Split, 9-Split, 16-Split

7.3.3 Site List Panel

The site list panel shows registered NVR lists. To connect, Drag & Drop the site.

Before you connect the site, Select the Live or Search mode first in the connection mode panel.

16 different On-Screen NVR, a mixture of different connection modes can be monitored.

User’s Manual | 100

7.3.4 Calendar Panel

Activated in Search Mode

The recorded data will be shown in blue bold with the dot which is located below the number

When you click the recorded date on the search mode, the playback time will be detected automatically

( Go Button ) should be pressed to start playback from the selected date and time

If DST is enabled, the earlier one-hour overlapped video will be shown first.

101 | Chapter 1 : NVR

7.3.5 Search Panel

Activated in Search Mode

No

1

2

3

4

5

6

7

- The Search panel shows the record information for each channel.

- Each record mode is like below.

No Record Background Color

Continuous (Yellow Color)

Instant(Red Color)

Alarm(Orange Color)

Motion(Green Color)

- Click the time or move the time bar to the time you want to playback in the search panel.

- Playback control panel

Button Description

Go to first

Forward Playback : Decrease the Speed / Reverse Playback : Increase the Speed

Reverse Playback

Pause

Forward Playback

Forward Playback : Increase the speed / Reverse Playback : Decrease the speed

Go 10 seconds before the end of the data.

7.3.6 Site Manager

Add or Modify or Remove NVR site information.

User’s Manual | 102

Press to register the NVR as follows : The default value is registered

103 | Chapter 1 : NVR

To fix, Double-Click on the item. For example, Double-click “ New Site “ to change the name.

After modifications have been made, press

No.

1

2

3

4

5

6

7

Function

Name

IP

Port

User ID

User Password

Ch.

Model

Description

Fill in the name of the site to be registered

Fill in the IP of the site to be registered

Fill in the PORT No of the site to be registered (Default 9010)

Fill in the ID of the NVR to be connected

Fill in the PW of the NVR to be connected

Fill in channel of the site to be registered

(ex, 16 Ch NVR: 1-16 or Registered by Camera : 1,3,5,7,9)

Select Model name of the NVR to be registered

Please double click the items, if you want to change the item from the registered information.

If you want to delete the registered NVR information, Select the NVR and click

After modifications have been made, press

User’s Manual | 104

105 | Chapter 1 : NVR

Chapter 4

M

OBILE

P

HONE

S

OFTWARE

U

SER

M

ANUAL

8 M

OBILE

P

HONE

S

OFTWARE

U

SER

G

UIDE

8.1 iPhone application software

User’s Manual | 106

107 | Chapter 4 : Mobile Phone Software User Manual

User’s Manual | 108

109 | Chapter 4 : Mobile Phone Software User Manual

User’s Manual | 110

111 | Chapter 4 : Mobile Phone Software User Manual

User’s Manual | 112

113 | Chapter 4 : Mobile Phone Software User Manual

User’s Manual | 114

PTZ camera control is not available on the NVR system.

115 | Chapter 4 : Mobile Phone Software User Manual

User’s Manual | 116

117 | Chapter 4 : Mobile Phone Software User Manual

8.2 Android application software

User’s Manual | 118

119 | Chapter 4 : Mobile Phone Software User Manual

User’s Manual | 120

121 | Chapter 4 : Mobile Phone Software User Manual

User’s Manual | 122

123 | Chapter 4 : Mobile Phone Software User Manual

User’s Manual | 124

PTZ camera control is not available on the NVR system.

125 | Chapter 4 : Mobile Phone Software User Manual

User’s Manual | 126

127 | Chapter 4 : Mobile Phone Software User Manual

8.3 Using WAP+3G Connection

User’s Manual | 128

129 | Chapter 4 : Mobile Phone Software User Manual

130 | FULL HD Network Video Recorder

131 | Appendix : DynDNS Site Registration

9 A

PPENDIX

: D

YN

DNS S

ITE

R

EGISTRATION

1) Go to www.dyndns.com

2) Log in to the Site after registration

3) Click “ Add Hostname“ button on “Host Services”

4) Put in the IP address and Host name on the blank

5) Click “NEXT” Button

6) Click “Activate Services” button

User’s Manual | 132

133 | Appendix : DynDNS Site Registration

7) Confirm the domain name and IP address

8) Check the connection status

User’s Manual | 134

Tip

1. It may take a little time to be completely done for DNS deployment after changed sub domain.

2. Please recheck NVR’s IP address registered in the My Service Menu, if you can’t access NVR using dyndns.

3. If you are using dyndns to change the IP address for the NVR to the update request, dyndns update by the circumstances that may be late.

4. Dyndns domain is registered by the policy. If the update occurs frequently, it may be blocking.

Please recheck NVR’s service status registered in the My Service Menu, if you don’t access dyndns.

5. If you don’t access dyndns for a long time, domain will be deleted automatically.

To prevent this, please access it regularly, or you will have to pay for it again.

For more information, please contact to dyndns directly

135 | FULL HD Network Video Recorder

User’s Manual | 136

10 A

PPENDIX

: S

PECIFICATION

Full HD Network Video Recorder 4/8CH

Design

Compression

Video

Audio

HDD Interface

Operation System

Video Output

Decoding

Live &

Playback

Display Mode

Search Mode

Record

Main Stream

Second

Stream

Mode

Interface

Network

Interface

Option

Protocol

USB

PoE

Mobile apps

PTZ

Audio In / Out

Alarm

Power

Accessories

Operating Temperature

Operating Humidity

Support IP Camera

Certification

Dimension(W x H x D)

H.264, JPEG supported

ADPCM, PCM supported

1EA x SATA I / II / III

Embedded Linux

HDMI (1920x1080p/1280x720p/1280x1024/1024x768)

Max 120fps @ 1080P (30fps per CH)

1/4 auto sequence, Main stream(Recording),

Second stream(Mobile/WEB)

Date/Time, Record Table, Calendar, Event,

Bookmark,System log, Event log

Max 120fps @ 1080P (30fps per CH)

Real Time Recording available Up to WVGA

Continuous, Event(Motion, Sensor), Pre-alarm, Post-alarm

1x 10/100/1000Mbps WAN port, 4 x 10/100Mbps LAN port

TCP/IP, DHCP, NTP, HTTP, DDNS, RTP, RTSP, FTP, SMTP, OnViF, uPnP

2 x USB 2.0

4 ports ( 802.3 AF supported) iPhone, iPad, Android, Kindle fire

Network Protocol

1 x Audio in, 1 x Audio out

1/1

12V / 3A, PoE: 48V / 1.4A

Mouse

0

0

C ~ 40

0

C

0% ~ 90%

Onvif

CE, WEEE, RoHS

280 x 48 x 245mm

N

OTE

The specification is subject to change without any notice.

137 | Appendix : Specification

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement