MikroElektronika mikroPASCAL PRO for PIC User manual

mikroPascal PRO for PIC
April 2009.
Reader’s note
DISCLAIMER:
mikroPASCAL PRO for PIC and this manual are owned by mikroElektronika and are pro-
Reader’s Note
tected by copyright law and international copyright treaty. Therefore, you should treat this
manual like any other copyrighted material (e.g., a book). The manual and the compiler
may not be copied, partially or as a whole without the written consent from the mikroEelktronika. The PDF-edition of the manual can be printed for private or local use, but not for
distribution. Modifying the manual or the compiler is strictly prohibited.
HIGH RISK ACTIVITIES:
The mikroPASCAL PRO for PICcompiler is not fault-tolerant and is not designed, manufactured or intended for use or resale as on-line control equipment in hazardous environments
requiring fail-safe performance, such as in the operation of nuclear facilities, aircraft navigation
or communication systems, air traffic control, direct life support machines, or weapons systems, in which the failure of the Software could lead directly to death, personal injury, or severe
physical or environmental damage ("High Risk Activities"). mikroElektronika and its suppliers
specifically disclaim any express or implied warranty of fitness for High Risk Activities.
LICENSE AGREEMENT:
By using the mikroPASCAL PRO for PIC compiler, you agree to the terms of this agreement.
Only one person may use licensed version of mikroPascal PRO for PIC compiler at a time.
Copyright © mikroElektronika 2003 - 2009.
This manual covers mikroPASCAL PRO for PIC version 1.0 and the related topics.
Newer versions may contain changes without prior notice.
COMPILER BUG REPORTS:
The compiler has been carefully tested and debugged. It is, however, not possible to
guarantee a 100 % error free product. If you would like to report a bug, please contact us at
the address [email protected]. Please include next information in your bug report:
- Your operating system
- Version of mikroPASCAL PRO for PIC
- Code sample
- Description of a bug
CONTACT US:
mikroElektronika
Voice: + 381 (11) 36 28 830
Fax:
+ 381 (11) 36 28 831
Web:
www.mikroe.com
E-mail: [email protected]
Windows is a Registered trademark of Microsoft Corp. All other trade and/or services marks
are the property of the respective owners.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
Table of Contents
CHAPTER 1
Introduction
CHAPTER 2
mikroPASCAL PRO for PIC Environment
CHAPTER 3
mikroICD (In-Circuit Debugger)
CHAPTER 4
mikroPASCAL PRO for PIC Specifics
CHAPTER 5
PIC Specifics
CHAPTER 6
mikroPASCAL PRO for PIC Language Reference
CHAPTER 7
mikroPASCAL PRO for PIC Libraries
mikroPascal PRO for PIC
Table of Contents
CHAPTER 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Where to Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
mikroElektronika Associates License Statement and Limited Warranty 4
IMPORTANT - READ CAREFULLY . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
HIGH RISK ACTIVITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
GENERAL PROVISIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
How to Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Who Gets the License Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
How to Get License Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
After Receving the License Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
CHAPTER 2
Main Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
File Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Edit Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Find Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replace Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Find In Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Go To Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Regular expressions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
View Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Toolbars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
File Toolbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Edit Toolbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Advanced Edit Toolbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Find/Replace Toolbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Project Toolbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Build Toolbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Debugger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Styles Toolbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tools Toolbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IV
13
14
15
16
17
17
18
18
19
20
20
20
21
21
22
22
23
23
24
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
mikroPASCAL PRO for PIC
Table of Contents
Project Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Run Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Tools Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Help Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Keyboard Shortcuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
IDE Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Customizing IDE Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Docking Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Saving Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Auto Hide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Advanced Code Editor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Advanced Editor Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Code Assistant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Code Folding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Parameter Assistant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Code Templates (Auto Complete) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Auto Correct . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Spell Checker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Bookmarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Goto Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Comment / Uncomment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Code Explorer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Routine List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Project Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Project Settings Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Library Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Error Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Memory Usage Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
RAM Memory Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Used RAM Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
SFR Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
ROM Memory Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
ROM Memory Constants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Functions Sorted By Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Functions Sorted By Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
V
Table of Contents
mikroPascal PRO for PIC
Functions Sorted By Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Functions Sorted By Name Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Functions Sorted By Size Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Functions Sorted By Addresses Chart . . . . . . . . . . . . . . . . . . . . . . . . . 57
Function Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Memory Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Integrated Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
USART Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
EEPROM Editor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
ASCII Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Seven Segment Convertor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Lcd Custom Character . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Graphic Lcd Bitmap Editor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
HID Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
UDP Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
mikroBootloader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
What is a Bootloader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
How to use mikroBootloader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Integrating User Code and Boot Code . . . . . . . . . . . . . . . . . . . . . . . . . 68
Macro Editor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Code editor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Output settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Regular Expressions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Simple matches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Escape sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Character classes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Metacharacters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Metacharacters - Line separators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Metacharacters - Predefined classes . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Metacharacters - Word boundaries . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Metacharacters - Iterators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Metacharacters - Alternatives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
VI
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
mikroPASCAL PRO for PIC
Table of Contents
Metacharacters - Subexpressions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Metacharacters - Backreferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
mikroPascal PRO for PIC Command Line Options . . . . . . . . . . . . . . . . 77
Projects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
New Project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
New Project Wizard Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Customizing Projects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Managing Project Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Add/Remove Files from Project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
The project can contain the fol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Project Level Defines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Source Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Managing Source Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Creating new source file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Opening an existing file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Printing an open file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Saving file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Saving file under a different name . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Closing file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Clean Project Folder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Compilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Output Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Assembly View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Compiler Error Messages: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Warning Messages: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Hint Messages: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Software Simulator Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Breakpoints Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Watch Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
View RAM Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Stopwatch Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Software Simulator Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Creating New Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Multiple Library Versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
VII
mikroPascal PRO for PIC
Table of Contents
CHAPTER 3
mikroICD Debugger Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
mikroICD Debugger Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
mikroICD (In-Circuit Debugger) Overview . . . . . . . . . . . . . . . . . . . . . . . 106
Breakpoints Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Watch Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
EEPROM Watch Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Code Watch Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
View RAM Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Common Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
mikroICD Advanced Breakpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
mikroICD provides the possibili . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Program Memory Break . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
File Register Break . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Emulator Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Event Breakpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Stopwatch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
CHAPTER 4
Pascal Standard Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Divergence from the Pascal Standard . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Pascal Language Extensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Predefined Globals and Constants . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
SFRs and related constants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Math constants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Predefined project level defines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Accessing Individual Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Accessing Individual Bits Of Variables . . . . . . . . . . . . . . . . . . . . . . . . . 116
sbit type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
bit type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
P18 priority interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Routine Calls from Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Interrupt Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
VIII
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
mikroPASCAL PRO for PIC
Table of Contents
Linker Directives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Directive absolute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Directive org . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Directive orgall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Built-in Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Lo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Hi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Higher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Highest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Inc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Dec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
SetBit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
ClearBit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
TestBit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Delay_us . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Delay_ms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Clock_KHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Clock_MHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
ClrWdt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
DisableContextSaving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
SetFuncCall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
GetDateTime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
GetVersion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Code Optimization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Constant folding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Constant propagation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Copy propagation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Value numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
"Dead code" ellimination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Stack allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Local vars optimization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Better code generation and local optimization . . . . . . . . . . . . . . . . . . . 130
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
IX
mikroPascal PRO for PIC
Table of Contents
CHAPTER 5
Types Efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Nested Calls Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
PIC18FxxJxx Specifics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Shared Address SFRs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
PIC16 Specifics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Breaking Through Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Limits of Indirect Approach Through FSR . . . . . . . . . . . . . . . . . . . . . . . 133
Memory Type Specifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
rx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
sfr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
CHAPTER 6
Lexical Elements Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Whitespace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Whitespace in Strings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Comments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Nested comments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Tokens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Token Extraction Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Literals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Integer Literals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Floating Point Literals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Character Literals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
String Literals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Keywords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Identifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Case Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Uniqueness and Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Identifier Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Punctuators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
X
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
mikroPASCAL PRO for PIC
Table of Contents
Parentheses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Comma . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Semicolon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Colon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Dot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Program Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Organization of Main Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Organization of Other Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Scope and Visibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Visibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Uses Clause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Main Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Other Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Interface Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Implementation Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
External Modifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Variables and PIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Constants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Functions and Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Calling a function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Calling a procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Example: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Forward declaration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Functions reentrancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Type Categories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Simple Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Arrays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
XI
Table of Contents
mikroPascal PRO for PIC
Array Declaration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
Constant Arrays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
Multi-dimensional Arrays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
Strings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
String Concatenating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Pointers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Function Pointers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Example: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
@ Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
Accessing Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Types Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
Implicit Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
Promotion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
Clipping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
Explicit Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
Conversions Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
Operators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Operators Precedence and Associativity . . . . . . . . . . . . . . . . . . . . . . . . 175
Arithmetic Operators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Division by Zero . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Unary Arithmetic Operators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Relational Operators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Relational Operators in Expressions . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Bitwise Operators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
Bitwise Operators Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
Logical Operations on Bit Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
Bitwise operators and, or, and xor perform logical operation . . . . . . . . 178
Unsigned and Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
Signed and Conversions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
Bitwise Shift Operators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
Boolean Operators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
Expressions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
Assignment Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
XII
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
mikroPASCAL PRO for PIC
Table of Contents
Compound Statements (Blocks) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
Conditional Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
If Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
Nested if statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
Case statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
Nested Case statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
Iteration Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
For Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
Endless Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
While Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
Repeat Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
Jump Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
Break and Continue Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
Break Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
Continue Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
Exit Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
Goto Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
asm Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
Directives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
Compiler Directives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
Directives $DEFINE and $UNDEFINE . . . . . . . . . . . . . . . . . . . . . . . . . 193
Directives $IFDEF, $IFNDEF, $ELSE . . . . . . . . . . . . . . . . . . . . . . . . . . 193
Include Directive $I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
Predefined Flags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
Linker Directives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
Directive absolute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
Directive org . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
Directive orgall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
CHAPTER 7
Hardware PIC-specific Libraries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
Miscellaneous Libraries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
Library Dependencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
Hardware Libraries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
ADC Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
XIII
Table of Contents
mikroPascal PRO for PIC
ADC_Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
HW Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
CAN Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
CANSetOperationMode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
CANGetOperationMode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
CANInitialize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
CANSetBaudRate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
CANSetMask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
CANSetFilter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
CANRead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
CANWrite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
CAN Constants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
CAN_CONFIG_FLAGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211
CAN_TX_MSG_FLAGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
CAN_RX_MSG_FLAGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
CAN_MASK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
CAN_FILTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
HW Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
CANSPI Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
External dependencies of CANSPI Library . . . . . . . . . . . . . . . . . . . . . . 218
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218
CANSPISetOperationMode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
CANSPIGetOperationMode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220
CANSPIInitialize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220
CANSPISetBaudRate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
CANSPISetMask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
CANSPISetFilter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
CANSPIRead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225
CANSPIWrite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226
CANSPI Constants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226
CANSPI_OP_MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227
CANSPI_CONFIG_FLAGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227
CANSPI_TX_MSG_FLAGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
XIV
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
mikroPASCAL PRO for PIC
Table of Contents
CANSPI_RX_MSG_FLAGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
CANSPI_MASK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229
CANSPI_FILTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
HW Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
Compact Flash Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234
External dependencies of Compact Flash Library . . . . . . . . . . . . . . . . 235
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236
Cf_Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237
Cf_Detect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238
Cf_Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238
Cf_Disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238
Cf_Read_Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239
Cf_Read_Byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239
Cf_Write_Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240
Cf_Write_Byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240
Cf_Read_Sector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241
Cf_Write_Sector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241
Cf_Fat_Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242
Cf_Fat_QuickFormat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242
Cf_Fat_Assign . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
Cf_Fat_Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244
Cf_Fat_Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 244
Cf_Fat_Rewrite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
Cf_Fat_Append . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
Cf_Fat_Delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
Cf_Fat_Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246
Cf_Fat_Set_File_Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246
Cf_Fat_Get_File_Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
Cf_Fat_Get_File_Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
Cf_Fat_Get_Swap_File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250
HW Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255
EEPROM Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
EEPROM_Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
XV
Table of Contents
mikroPascal PRO for PIC
EEPROM_Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
Ethernet PIC18FxxJ60 Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259
Ethernet_Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260
Ethernet_Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261
Ethernet_Disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262
Ethernet_doPacket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263
Ethernet_putByte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264
Ethernet_putBytes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264
Ethernet_putConstBytes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
Ethernet_putString . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
Ethernet_putConstString . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266
Ethernet_getByte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266
Ethernet_getBytes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267
Ethernet_UserTCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
Ethernet_UserUDP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 269
Ethernet_getIpAddress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270
Ethernet_getGwIpAddress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270
Ethernet_getDnsIpAddress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271
Ethernet_getIpMask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271
Ethernet_confNetwork . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272
Ethernet_arpResolve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273
Ethernet_sendUDP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274
Ethernet_dnsResolve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275
Ethernet_initDHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
Ethernet_doDHCPLeaseTime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277
Ethernet_renewDHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278
Flash Memory Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
FLASH_Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
FLASH_Read_N_Bytes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
FLASH_Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288
FLASH_Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
FLASH_Erase_Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
XVI
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
mikroPASCAL PRO for PIC
Table of Contents
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290
Graphic Lcd Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292
External dependencies of Graphic Lcd Library . . . . . . . . . . . . . . . . . . . 292
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293
Glcd_Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294
Glcd_Set_Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295
Glcd_Set_X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295
Glcd_Set_Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296
Glcd_Read_Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296
Glcd_Write_Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297
Glcd_Fill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297
Glcd_Dot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298
Glcd_Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298
Glcd_V_Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299
Glcd_H_Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299
Glcd_Rectangle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300
Glcd_Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300
Glcd_Circle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301
Glcd_Set_Font . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301
Glcd_Write_Char . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302
Glcd_Write_Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303
Glcd_Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 304
HW Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306
I²C Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307
I2C1_Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307
I2C1_Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308
I2C1_Repeated_Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308
I2C1_Is_Idle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308
I2C1_Rd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308
I2C1_Wr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309
I2C1_Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309
HW Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 310
Keypad Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
XVII
Table of Contents
mikroPascal PRO for PIC
External dependencies of Keypad Library . . . . . . . . . . . . . . . . . . . . . . . 311
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311
Keypad_Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311
Keypad_Key_Press . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312
Keypad_Key_Click . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312
This is a simple example of using . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312
he Keypad Librar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312
HW Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315
Lcd Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 316
External dependencies of Lcd Library . . . . . . . . . . . . . . . . . . . . . . . . . . 316
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317
Lcd_Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317
Lcd_Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318
Lcd_Out_CP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318
Lcd_Chr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
Lcd_Chr_CP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
Lcd_Cmd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320
Available Lcd Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321
HW connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323
Lcd HW connecti . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323
Manchester Code Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324
External dependencies of Manchester Code Library . . . . . . . . . . . . . . 324
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
Man_Receive_Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
Man_Receive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326
Man_Send_Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326
Man_Send . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327
Man_Synchro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327
Man_Break . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
Connection Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332
Multi Media Card Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333
Secure Digital Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333
External dependencies of MMC Library . . . . . . . . . . . . . . . . . . . . . . . . 334
XVIII
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
mikroPASCAL PRO for PIC
Table of Contents
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334
Mmc_Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335
Mmc_Read_Sector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336
Mmc_Write_Sector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336
Mmc_Read_Cid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 337
Mmc_Read_Csd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 337
Mmc_Fat_Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338
Mmc_Fat_QuickFormat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339
Mmc_Fat_Assign . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 340
Mmc_Fat_Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341
Mmc_Fat_Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341
Mmc_Fat_Rewrite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342
Mmc_Fat_Append . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342
Mmc_Fat_Delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342
Mmc_Fat_Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 343
Mmc_Fat_Set_File_Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 344
Mmc_Fat_Get_File_Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345
Mmc_Fat_Get_File_Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345
Mmc_Fat_Get_Swap_File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 346
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347
The following exa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347
HW Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350
OneWire Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 351
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 351
Ow_Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 352
Ow_Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 352
Ow_Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 352
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 352
This example reads the tem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 352
erature using DS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 352
HW Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355
Port Expander Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356
External dependencies of Port Expander Library . . . . . . . . . . . . . . . . . 356
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356
Expander_Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357
Expander_Read_Byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 358
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
XIX
Table of Contents
mikroPascal PRO for PIC
Expander_Write_Byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 358
Expander_Read_PortA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359
Expander_Read_PortB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360
Expander_Read_PortAB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 361
Expander_Write_PortA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 362
Expander_Write_PortB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363
Expander_Write_PortAB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 364
Expander_Set_DirectionPortA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365
Expander_Set_DirectionPortB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365
Expander_Set_DirectionPortAB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366
Expander_Set_PullUpsPortA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366
Expander_Set_PullUpsPortB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367
Expander_Set_PullUpsPortAB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368
HW Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369
PS/2 Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370
External dependencies of PS/2 Library . . . . . . . . . . . . . . . . . . . . . . . . . 370
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 370
Ps2_Config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371
Ps2_Key_Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 372
Special Function Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374
HW Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375
PWM Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 376
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 376
PWM1_Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 376
PWM1_Set_Duty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 377
PWM1_Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 377
PWM1_Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 377
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 377
HW Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379
RS-485 Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 380
External dependencies of RS-485 Library . . . . . . . . . . . . . . . . . . . . . . . 380
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 381
RS485Master_Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 381
RS485Master_Receive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382
XX
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
mikroPASCAL PRO for PIC
Table of Contents
RS485Master_Send . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383
RS485Slave_Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 384
RS485slave_Receive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385
RS485Slave_Send . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386
HW Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390
Message format and CRC calculations . . . . . . . . . . . . . . . . . . . . . . . . . 391
Software I²C Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392
External dependencies of Software I²C Library . . . . . . . . . . . . . . . . . . . 392
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392
Soft_I2C_Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393
Soft_I2C_Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393
Soft_I2C_Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394
Soft_I2C_Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394
Soft_I2C_Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395
Soft_I2C_Break . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396
Software SPI Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399
External dependencies of Software SPI Library . . . . . . . . . . . . . . . . . . 399
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399
Soft_SPI_Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400
Soft_SPI_Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 401
Soft_SPI_Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 401
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 401
Software UART Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 404
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 404
Soft_UART_Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 405
Soft_UART_Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406
Soft_UART_Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407
Soft_UART_Break . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 408
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409
Sound Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 410
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 410
Sound_Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 410
Sound_Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 411
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 411
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
XXI
Table of Contents
mikroPascal PRO for PIC
HW Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 414
SPI Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415
SPI1_Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415
SPI1_Init_Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 416
SPI1_Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 417
SPI1_Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 417
SPI_Set_Active . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 417
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 418
HW Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419
SPI Ethernet Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 420
External dependencies of SPI Ethernet Library . . . . . . . . . . . . . . . . . . 421
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 422
PIC16 and PIC18: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 422
PIC18 Only: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 422
SPI_Ethernet_Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423
SPI_Ethernet_Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 425
SPI_Ethernet_Disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 426
SPI_Ethernet_doPacket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 427
SPI_Ethernet_putByte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 428
SPI_Ethernet_putBytes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 428
SPI_Ethernet_putConstBytes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429
SPI_Ethernet_putString . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429
SPI_Ethernet_putConstString . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 430
SPI_Ethernet_getByte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 430
SPI_Ethernet_getBytes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 431
SPI_Ethernet_UserTCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 432
SPI_Ethernet_UserUDP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 433
SPI_Ethernet_getIpAddress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 434
SPI_Ethernet_getGwIpAddress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 434
SPI_Ethernet_getDnsIpAddress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 435
SPI_Ethernet_getIpMask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 435
SPI_Ethernet_confNetwork . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436
SPI_Ethernet_arpResolve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 437
SPI_Ethernet_sendUDP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 438
SPI_Ethernet_dnsResolve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 439
XXII
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
mikroPASCAL PRO for PIC
Table of Contents
SPI_Ethernet_initDHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 440
SPI_Ethernet_doDHCPLeaseTime . . . . . . . . . . . . . . . . . . . . . . . . . . . . 441
SPI_Ethernet_renewDHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 441
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 442
HW Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449
SPI Graphic Lcd Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450
External dependencies of SPI Graphic Lcd Library . . . . . . . . . . . . . . . 450
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450
SPI_Glcd_Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 451
SPI_Glcd_Set_Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 452
SPI_Glcd_Set_Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 452
SPI_Glcd_Set_X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 453
SPI_Glcd_Read_Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 453
SPI_Glcd_Write_Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454
SPI_Glcd_Fill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 454
SPI_Glcd_Dot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 455
SPI_Glcd_Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 455
SPI_Glcd_V_Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 456
SPI_Glcd_H_Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 456
SPI_Glcd_Rectangle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 457
SPI_Glcd_Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 458
SPI_Glcd_Circle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 458
SPI_Glcd_Set_Font . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 459
SPI_Glcd_Write_Char . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 460
SPI_Glcd_Write_Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 461
SPI_Glcd_Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 462
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 462
HW Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 465
SPI Lcd Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 466
External dependencies of SPI Lcd Library . . . . . . . . . . . . . . . . . . . . . . 466
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 466
SPI_Lcd_Config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 467
SPI_Lcd_Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 468
SPI_Lcd_Out_CP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 468
SPI_Lcd_Chr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 469
SPI_Lcd_Chr_CP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 469
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
XXIII
Table of Contents
mikroPascal PRO for PIC
SPI_Lcd_Cmd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 470
Available SPI Lcd Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 470
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 471
HW Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 472
SPI Lcd8 (8-bit interface) Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 473
External dependencies of SPI Lcd Library . . . . . . . . . . . . . . . . . . . . . . 473
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 473
SPI_Lcd8_Config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 474
SPI_Lcd8_Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475
SPI_Lcd8_Out_CP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475
SPI_Lcd8_Chr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 476
SPI_Lcd8_Chr_CP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 476
SPI_Lcd8_Cmd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 477
Available SPI Lcd8 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 477
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 478
HW Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 479
SPI T6963C Graphic Lcd Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 480
External dependencies of SPI T6963C Graphic Lcd Library . . . . . . . . 480
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 481
SPI_T6963C_Config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 482
SPI_T6963C_WriteData . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 483
SPI_T6963C_WriteCommand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 484
SPI_T6963C_SetPtr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 484
SPI_T6963C_WaitReady . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 484
SPI_T6963C_Fill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 485
SPI_T6963C_Dot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 485
SPI_T6963C_Write_Char . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 486
SPI_T6963C_Write_Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 487
SPI_T6963C_Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 488
SPI_T6963C_Rectangle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 488
SPI_T6963C_Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 489
SPI_T6963C_Circle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 489
SPI_T6963C_Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 490
SPI_T6963C_Sprite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 490
SPI_T6963C_Set_Cursor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 491
SPI_T6963C_ClearBit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 491
XXIV
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
mikroPASCAL PRO for PIC
Table of Contents
SPI_T6963C_SetBit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 491
SPI_T6963C_NegBit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 492
SPI_T6963C_DisplayGrPanel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 492
SPI_T6963C_DisplayTxtPanel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 493
SPI_T6963C_SetGrPanel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 493
SPI_T6963C_SetTxtPanel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 494
SPI_T6963C_PanelFill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 494
SPI_T6963C_GrFill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 494
SPI_T6963C_TxtFill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 495
SPI_T6963C_Cursor_Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 495
SPI_T6963C_Graphics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 495
SPI_T6963C_Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 496
SPI_T6963C_Cursor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 496
SPI_T6963C_Cursor_Blink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 496
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 497
HW Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 502
T6963C Graphic Lcd Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 503
External dependencies of T6963C Graphic Lcd Library . . . . . . . . . . . . 504
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 505
T6963C_Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 506
T6963C_WriteData . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 507
T6963C_WriteCommand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 507
T6963C_SetPtr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 508
T6963C_WaitReady . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 508
T6963C_Fill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 508
T6963C_Dot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 509
T6963C_Write_Char . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 509
T6963C_Write_Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 510
T6963C_Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 511
T6963C_Rectangle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 511
T6963C_Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 512
T6963C_Circle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 512
T6963C_Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 513
T6963C_Sprite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 513
T6963C_Set_Cursor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 514
T6963C_DisplayGrPanel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 514
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
XXV
Table of Contents
mikroPASCAL PRO for PIC
T6963C_DisplayTxtPanel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 514
T6963C_SetGrPanel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515
T6963C_SetTxtPanel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515
T6963C_PanelFill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515
T6963C_GrFill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 516
T6963C_TxtFill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 516
T6963C_Cursor_Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 516
T6963C_Graphics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 517
T6963C_Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 517
T6963C_Cursor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 517
T6963C_Cursor_Blink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 518
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 518
HW Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 523
UART Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 524
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 524
UART1_Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 525
UART1_Data_Ready . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 526
UART1_Tx_Idle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 526
UART1_Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 527
UART1_Read_Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 527
UART1_Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 528
UART1_Write_Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 528
UART_Set_Active . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 529
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 529
HW Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530
USB HID Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 531
Descriptor File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 531
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 531
Hid_Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 531
Hid_Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 532
Hid_Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 532
Hid_Disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 532
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 532
HW Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 534
Miscellaneous Libraries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 535
Button Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 535
XXVI
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
mikroPASCAL PRO for PIC
Table of Contents
Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 535
Conversions Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 536
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 536
ByteToStr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 536
ShortToStr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 537
WordToStr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 537
IntToStr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 538
LongintToStr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 538
LongWordToStr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 539
FloatToStr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 540
StrToInt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 541
StrToWord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 541
Dec2Bcd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 541
Bcd2Dec16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 542
Dec2Bcd16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 542
Math Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 543
Library Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 543
acos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 543
asin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 543
atan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 544
atan2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 544
ceil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 544
cos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 544
cosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 544
eval_poly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 544
exp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 544
fabs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 545
floor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 545
frexp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 545
ldexp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 545
log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 545
log10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 545
modf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 545
pow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 546
sin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 546
sinh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 546
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
XXVII
Table of Contents
mikroPASCAL PRO for PIC
sqrt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 546
tan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 546
tanh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 546
String Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 547
Library Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 547
memchr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 547
memcmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 548
memcpy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 548
memmove . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 548
memset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 549
strcat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 549
strchr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 549
strcmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 549
strcpy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 550
strcspn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 550
strlen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 550
strncat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 550
strncmp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 550
strncpy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 551
strpbrk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 551
strrchr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 551
strspn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 551
strstr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 551
Time Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 552
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 552
Time_dateToEpoch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 552
Time_epochToDate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 553
Time_dateDiff . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 553
Library Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 554
TimeStruct type definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 554
Trigonometry Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 555
Library Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 555
sinE3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 555
cosE3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 556
XXVIII MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER
1
Introduction to
mikroPascal PRO for PIC
Help version: 2009/03/19
The mikroPascal PRO for PIC is a powerful, feature-rich development tool for PIC
microcontrollers. It is designed to provide the programmer with the easiest possible solution to developing applications for embedded systems, without compromising performance or control.
1
CHAPTER 1
mikroPASCAL PRO for PIC
Introduction
mikroPascal PRO for PIC IDE
Features
mikroPascal PRO for PIC allows you to quickly develop and deploy complex applications:
- Write your Pascal source code using the built-in Code Editor (Code and Parameter
Assistants, Code Folding, Syntax Highlighting, Auto Correct, Code Templates, and more.)
- Use included mikroPascal PRO for PIC libraries to dramatically speed up the development: data acquisition, memory, displays, conversions, communication etc.
- Monitor your program structure, variables, and functions in the Code Explorer.
- Generate commented, human-readable assembly, and standard HEX compatible with
all programmers.
- Use the integrated mikroICD (In-Circuit Debugger) Real-Time debugging tool to monitor
program execution on the hardware level.
- Inspect program flow and debug executable logic with the integrated Software Simulator.
- Get detailed reports and graphs: RAM and ROM map, code statistics, assembly listing,
calling tree, and more.
- mikroPascal PRO for PIC provides plenty of examples to expand, develop, and use as
building bricks in your projects. Copy them entirely if you deem fit – that’s why we included them with the compiler.
2
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 1
mikroPASCAL PRO for PIC
Introduction
Where to Start
- In case that you’re a beginner in programming PIC microcontrollers, read carefully the PIC Specifics chapter. It might give you some useful pointers on PIC
constraints, code portability, and good programming practices.
- If you are experienced in Pascal programming, you will probably want to consult
mikroPascal PRO for PIC Specifics first. For language issues, you can always refer
to the comprehensive Language Reference. A complete list of included libraries is
available at mikroPascal PRO for PIC Libraries.
- If you are not very experienced in Pascal programming, don’t panic! mikroPascal
PRO for PIC provides plenty of examples making it easy for you to go quickly. We
suggest that you first consult Projects and Source Files, and then start browsing
the examples that you're the most interested in.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
3
CHAPTER 1
mikroPASCAL PRO for PIC
Introduction
MIKROELEKTRONIKA ASSOCIATES LICENSE STATEMENT AND
LIMITED WARRANTY
IMPORTANT - READ CAREFULLY
This license statement and limited warranty constitute a legal agreement (“License
Agreement”) between you (either as an individual or a single entity) and mikroElektronika (“mikroElektronika Associates”) for software product (“Software”) identified
above, including any software, media, and accompanying on-line or printed documentation.
BY INSTALLING, COPYING, OR OTHERWISE USING SOFTWARE, YOU AGREE
TO BE BOUND BY ALL TERMS AND CONDITIONS OF THE LICENSE
AGREEMENT.
Upon your acceptance of the terms and conditions of the License Agreement,
mikroElektronika Associates grants you the right to use Software in a way provided
below.
This Software is owned by mikroElektronika Associates and is protected by copyright law and international copyright treaty. Therefore, you must treat this Software
like any other copyright material (e.g., a book).
You may transfer Software and documentation on a permanent basis provided. You
retain no copies and the recipient agrees to the terms of the License Agreement.
Except as provided in the License Agreement, you may not transfer, rent, lease,
lend, copy, modify, translate, sublicense, time-share or electronically transmit or
receive Software, media or documentation. You acknowledge that Software in the
source code form remains a confidential trade secret of mikroElektronika Associates
and therefore you agree not to modify Software or attempt to reverse engineer,
decompile, or disassemble it, except and only to the extent that such activity is
expressly permitted by applicable law notwithstanding this limitation.
If you have purchased an upgrade version of Software, it constitutes a single product with the mikroElektronika Associates software that you upgraded. You may use
the upgrade version of Software only in accordance with the License Agreement.
4
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 1
mikroPASCAL PRO for PIC
Introduction
LIMITED WARRANTY
Respectfully excepting the Redistributables, which are provided “as is”, without warranty of any kind, mikroElektronika Associates warrants that Software, once updated and properly used, will perform substantially in accordance with the accompanying documentation, and Software media will be free from defects in materials and
workmanship, for a period of ninety (90) days from the date of receipt. Any implied
warranties on Software are limited to ninety (90) days.
mikroElektronika Associates’ and its suppliers’ entire liability and your exclusive
remedy shall be, at mikroElektronika Associates’ option, either (a) return of the price
paid, or (b) repair or replacement of Software that does not meet mikroElektronika
Associates’ Limited Warranty and which is returned to mikroElektronika Associates
with a copy of your receipt. DO NOT RETURN ANY PRODUCT UNTIL YOU HAVE
CALLED MIKROELEKTRONIKA ASSOCIATES FIRST AND OBTAINED A RETURN
AUTHORIZATION NUMBER. This Limited Warranty is void if failure of Software has
resulted from an accident, abuse, or misapplication. Any replacement of Software
will be warranted for the rest of the original warranty period or thirty (30) days,
whichever is longer.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW,
MIKROELEKTRONIKA ASSOCIATES AND ITS SUPPLIERS DISCLAIM ALL
OTHER WARRANTIES AND CONDITIONS, EITHER EXPRESSED OR IMPLIED,
INCLUDED, BUT NOT LIMITED TO IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND
NON-INFRINGEMENT, WITH REGARD TO SOFTWARE, AND THE PROVISION
OF OR FAILURE TO PROVIDE SUPPORT SERVICES.
IN NO EVENT SHALL MIKROELEKTRONIKA ASSOCIATES OR ITS SUPPLIERS
BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL
DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES
FOR LOSS OF BUSINESS PROFITS AND BUSINESS INFORMATION, BUSINESS
INTERRUPTION, OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE
USE OF OR INABILITY TO USE SOFTWARE PRODUCT OR THE PROVISION OF
OR
FAILURE
TO
PROVIDE
SUPPORT
SERVICES,
EVEN
IF
MIKROELEKTRONIKA ASSOCIATES HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES. IN ANY CASE, MIKROELEKTRONIKA ASSOCIATES’
ENTIRE LIABILITY UNDER ANY PROVISION OF THIS LICENSE AGREEMENT
SHALL BE LIMITED TO THE AMOUNT ACTUALLY PAID BY YOU FOR
SOFTWARE PRODUCT PROVIDED, HOWEVER, IF YOU HAVE ENTERED INTO
A MIKROELEKTRONIKA ASSOCIATES SUPPORT SERVICES AGREEMENT,
MIKROELEKTRONIKA ASSOCIATES’ ENTIRE LIABILITY REGARDING
SUPPORT SERVICES SHALL BE GOVERNED BY THE TERMS OF THAT
AGREEMENT.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
5
CHAPTER 1
mikroPASCAL PRO for PIC
Introduction
HIGH RISK ACTIVITIES
Software is not fault-tolerant and is not designed, manufactured or intended for use
or resale as on-line control equipment in hazardous environments requiring fail-safe
performance, such as in the operation of nuclear facilities, aircraft navigation or
communication systems, air traffic control, direct life support machines, or weapons
systems, in which the failure of Software could lead directly to death, personal injury,
or severe physical or environmental damage (“High Risk Activities”). mikroElektronika Associates and its suppliers specifically disclaim any expressed or implied warranty of fitness for High Risk Activities.
GENERAL PROVISIONS
This statement may only be modified in writing signed by you and an authorised officer of mikroElektronika Associates. If any provision of this statement is found void
or unenforceable, the remainder will remain valid and enforceable according to its
terms. If any remedy provided is determined to have failed for its essential purpose,
all limitations of liability and exclusions of damages set forth in the Limited Warranty shall remain in effect.
This statement gives you specific legal rights; you may have others, which vary, from
country to country. mikroElektronika Associates reserves all rights not specifically
granted in this statement.
mikroElektronika
Visegradska 1A,
11000 Belgrade,
Europe.
Phone: + 381 11 36 28 830
Fax: +381 11 36 28 831
Web: www.mikroe.com
E-mail: [email protected]
6
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 1
mikroPASCAL PRO for PIC
Introduction
TECHNICAL SUPPORT
In case you encounter any problem, you are welcome to our support forums at
www.mikroe.com/forum/. Here, you may also find helpful information, hardware tips,
and practical code snippets. Your comments and suggestions on future development of the mikroPascal PRO for PIC are always appreciated — feel free to drop a
note or two on our Wishlist.
In our Knowledge Base www.mikroe.com/en/kb/ you can find the answers to Frequently Asked Questions and solutions to known problems. If you can not find the
solution to your problem in Knowledge Base then report it to Support Desk
www.mikroe.com/en/support/. In this way, we can record and track down bugs more
efficiently, which is in our mutual interest. We respond to every bug report and question in a suitable manner, ever improving our technical support.
How to Register
The latest version of the mikroPascal PRO for PIC is always available for downloading from our website. It is a fully functional software libraries, examples, and comprehensive help included.
The only limitation of the free version is that it cannot generate hex output over 2
KB. Although it might sound restrictive, this margin allows you to develop practical,
working applications with no thinking of demo limit. If you intend to develop really
complex projects in the mikroPascal PRO for PIC, then you should consider the possibility of purchasing the license key.
Who Gets the License Key
Buyers of the mikroPascal PRO for PIC are entitled to the license key. After you
have completed the payment procedure, you have an option of registering your
mikroPascal. In this way you can generate hex output without any limitations.
How to Get License Key
After you have completed the payment procedure, start the program. Select Help ›
How to Register from the drop-down menu or click the How To Register Icon
.
Fill out the registration form (figure below), select your distributor, and click the Send
button.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
7
CHAPTER 1
Introduction
mikroPASCAL PRO for PIC
This will start your e-mail client with message ready for sending. Review the information you have entered, and add the comment if you deem it necessary. Please,
do not modify the subject line.
Upon receiving and verifying your request, we will send the license key to the e-mail
address you specified in the form.
8
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 1
mikroPASCAL PRO for PIC
Introduction
After Receving the License Key
The license key comes as a small autoextracting file – just start it anywhere on your
computer in order to activate your copy of compiler and remove the demo limit. You
do not need to restart your computer or install any additional components. Also,
there is no need to run the mikroPascal PRO for PIC at the time of activation.
Notes:
- The license key is valid until you format your hard disk. In case you need to format
the hard disk, you should request a new activation key.
- Please keep the activation program in a safe place. Every time you
upgrade the compiler you should start this program again in order to
reactivate the license.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
9
CHAPTER 1
Introduction
10
mikroPASCAL PRO for PIC
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER
2
mikroPASCAL PRO for PIC
Environment
11
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
IDE OVERVIEW
The mikroPascal PRO for PIC is an user-friendly and intuitive environment:
- The Code Editor features adjustable Syntax Highlighting, Code Folding, Code
Assistant, Parameters Assistant, Spell Checker, Auto Correct for common typos
and Code Templates (Auto Complete).
- The Code Explorer is at your disposal for easier project management.
- The Project Manager alows multiple project management
- General project settings can be made in the Project Settings window
- Library manager enables simple handling libraries being used in a project
- The Error Window displays all errors detected during compiling and linking.
- The source-level Software Simulator lets you debug executable logic step-by-step
by watching the program flow.
- The New Project Wizard is a fast, reliable, and easy way to create a project.
- Help files are syntax and context sensitive.
- Like in any modern Windows application, you may customize the layout of
mikroPascal PRO for PIC to suit your needs best.
- Spell checker underlines identifiers which are unknown to the project. In this way
it helps the programmer to spot potential problems early, much before the project
is compiled.
Spell checker can be disabled by choosing the option in the Preferences dialog (F12).
12
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
MAIN MENU OPTIONS
Available Main Menu options are:
Related topics: Keyboard shortcuts
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
13
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
FILE MENU OPTIONS
The File menu is the main entry point for manipulation with the source files.
File
Description
Open a new editor window.
Open source file for editing or image file for viewing.
Reopen recently used file.
Save changes for active editor.
Save the active source file with the different name or
change the file type.
Close active source file.
Print Preview.
Exit IDE.
Related topics: Keyboard shortcuts, File Toolbar, Managing Source Files
14
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
EDIT MENU OPTIONS
Edit
Description
Undo last change.
Redo last change.
Cut selected text to clipboard.
Copy selected text to clipboard.
Paste text from clipboard.
Delete selected text.
Select all text in active editor.
Find text in active editor.
Find next occurence of text in active editor.
Find previous occurence of text in active editor.
Replace text in active editor.
Find text in current file, in all opened files, or in files
from desired folder.
Goto to the desired line in active editor.
Advanced Code Editor options
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
15
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Advanced »
Description
Comment selected code or put single line comment if there is no selection.
Uncomment selected code or remove single line
comment if there is no selection.
Indent selected code.
Outdent selected code.
Changes selected text case to lowercase.
Changes selected text case to uppercase.
Changes selected text case to titlercase.
Find Text
Dialog box for searching the document for the specified text. The search is performed in the direction specified. If the string is not found a message is displayed.
16
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Replace Text
Dialog box for searching for a text string in file and replacing it with another text
string.
Find In Files
Dialog box for searching for a text string in current file, all opened files, or in files on
a disk.
The string to search for is specified in the Text to find field. If Search in directories option
is selected, The files to search are specified in the Files mask and Path fields.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
17
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Go To Line
Dialog box that allows the user to specify the line number at which the cursor should
be positioned.
Regular expressions
By checking this box, you will be able to advance your search, through Regular
expressions.
Related topics: Keyboard shortcuts, Edit Toolbar, Advanced Edit Toolbar
18
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
VIEW MENU OPTIONS
View
Description
Show/Hide toolbars.
Show/Hide Software Simulator/mikroICD (InCircuit Debugger) debug windows.
Show/Hide Routine List in active editor.
Show/Hide Project Settings window.
Show/Hide Code Explorer window.
Show/Hide Project Manager window.
Show/Hide Library Manager window.
Show/Hide Bookmarks window.
Show/Hide Error Messages window.
Show/Hide Macro Editor window.
Show Window List window.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
19
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
TOOLBARS
File Toolbar
File Toolbar is a standard toolbar with following options:
Icon
Description
Opens a new editor window.
Open source file for editing or image file for viewing.
Save changes for active window.
Save changes in all opened windows.
Close current editor.
Close all editors.
Print Preview.
Edit Toolbar
Edit Toolbar is a standard toolbar with following options:
Icon
Description
Undo last change.
Redo last change.
Cut selected text to clipboard.
Copy selected text to clipboard.
Paste text from clipboard.
20
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Advanced Edit Toolbar
Advanced Edit Toolbar comes with following options:
Icon
Description
Comment selected code or put single line comment if there is no selection
Uncomment selected code or remove single line comment if there is
no selection.
Select text from starting delimiter to ending delimiter.
Go to ending delimiter.
Go to line.
Indent selected code lines.
Outdent selected code lines.
Generate HTML code suitable for publishing current source code on
the web.
Find/Replace Toolbar
Find/Replace Toolbar is a standard toolbar with following options:
Icon
Description
Find text in current editor.
Find next occurence.
Find previous occurence.
Replace text.
Find text in files.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
21
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Project Toolbar
Project Toolbar comes with following options:
Icon
Description
New project.
Open Project
Save Project
Close current project.
Edit project settings.
Add existing project to project group.
Remove existing project from project group.
Add File To Project
Remove File From Project
Build Toolbar
Build Toolbar comes with following options:
Icon
Description
Build current project.
Build all opened projects.
Build and program active project.
Start programmer and load current HEX file.
Open assembly code in editor.
Open lisitng file in editor.
View statistics for current project.
22
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Debugger
Debugger Toolbar comes with following options:
Icon
Description
Start Software Simulator or mikroICD (In-Circuit Debugger).
Run/Pause debugger.
Stop debugger.
Step into.
Step over.
Step out.
Run to cursor.
Toggle breakpoint.
Toggle breakpoints.
Clear breakpoints.
View watch window
View stopwatch window
Styles Toolbar
Styles toolbar allows you to easily customize your workspace.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
23
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Tools Toolbar
Tools Toolbar comes with following default options:
Icon
Description
Run USART Terminal
EEPROM
ASCII Chart
Seven segment decoder tool.
Options menu
The Tools toolbar can easily be customized by adding new tools in Options(F12)
window.
Related topics: Keyboard shortcuts, Integrated Tools, Debugger Windows
24
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
PROJECT MENU OPTIONS
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
25
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Project
Description
Build active project.
Build all projects.
Build and program active project.
View Assembly.
Edit search paths.
Clean Project Folder
Add file to project.
Remove file from project.
Import projects created in previous versions of
mikroPascal.
Open New Project Wizard
Open existing project.
Save current project.
Edit project settings
Open project group.
Close project group.
Save active project file with the different name.
Open recently used project.
Close active project.
Related topics: Keyboard shortcuts, Project Toolbar, Creating New Project, Project
Manager, Project Settings
26
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
RUN MENU OPTIONS
Run
Description
Start Software Simulator or mikroICD (In-Circuit Debugger).
Stop debugger.
Pause Debugger.
Step Into.
Step Over.
Step Out.
Jump to interrupt in current project.
Toggle Breakpoint.
Breakpoints.
Clear Breakpoints.
Show/Hide Watch Window
Show/Hide Stopwatch Window
Toggle between Pascal source and disassembly.
Related topics: Keyboard shortcuts, Debug Toolbar
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
27
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
TOOLS MENU OPTIONS
Tools
Description
Run mikroElektronika Programmer
Run USART Terminal
Run EEPROM Editor
Run ASCII Chart
Run Seven Segment Convertor
Generate HTML code suitable for publishing
source code on the web.
Run Lcd custom character
Run Glcd bitmap editor
Run HID Terminal
Run UDP communication terminal
Run mikroBootloader
Open Options window
Related topics: Keyboard shortcuts, Tools Toolbar
28
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
HELP MENU OPTIONS
File
Description
Open Help File.
Open Code Migration Document.
Check if new compiler version is available.
Open mikroElektronika Support Forums in
a default browser.
Open mikroElektronika Web Page in a
default browser.
Information on how to register
Open About window.
Related topics: Keyboard shortcuts
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
29
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
KEYBOARD SHORTCUTS
Below is a complete list of keyboard shortcuts available in mikroPascal PRO for PIC IDE.
IDE Shortcuts
Ctrl+S
Save Unit
F1
Help
Ctrl+Shift+S
Save All
Ctrl+N
New Unit
Ctrl+V
Paste
Ctrl+O
Open
Ctrl+X
Cut
Ctrl+Shift+O
Open Project
Ctrl+Y
Delete Entire Line
Ctrl+Shift+N
New Project
Ctrl+Z
Undo
Ctrl+K
Close Project
Ctrl+Shift+Z
Redo
Ctrl+F4
Close unit
Ctrl+Shift+E
Edit Project
Ctrl+Space
Code Assistant
Ctrl+F9
Build
Ctrl+Shift+Space
Parameters Assistant
Shift+F9
Build All
Ctrl+D
Find Declaration
Ctrl+F11
Build And Program
Ctrl+E
Incremental Search
Shift+F4
View Breakpoints
Ctrl+L
Routine List
Ctrl+Shift+F5
Clear Breakpoints
Ctrl+G
Goto Line
F11
Start mE Programmer
Ctrl+J
Insert Code Template
Ctrl+Shift+F11 Project Manager
Ctrl+Shift+.
Comment Code
F12
Options
Ctrl+Shift+,
Uncomment Code
Alt + X
Close mikroPascal PRO for PIC
Ctrl+number
Goto Bookmark
Basic Editor Shortcuts
30
Advanced Editor Shortcuts
Ctrl+Shift+number Set Bookmark
F3
Find, Find Next
Ctrl+Shift+I
Indent Selection
Shift+F3
Find Previous
Ctrl+Shift+U
Unindent Selection
Alt+F3
Grep Search, Find In Files
TAB
Indent Selection
Ctrl+A
Select All
Shift+TAB
Unindent selection
Ctrl+C
Copy
Alt+Select
Select Columns
Ctrl+F
Find
Ctrl+Alt+Select
Select Columns
Ctrl+R
Replace
Ctrl+Alt+L
Convert Selection to Lowercase
Ctrl+P
Print
Ctrl+Alt+U
Convert Selection to Uppercase
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Ctrl+Alt+T
Environment
Convert to Titlecase
mikroICD Debugger and Software Simulator
Shortcuts
F2
Jump to Interrupt
F4
Run to Cursor
F5
Toggle Breakpoint
F6
Run/Pause Debugger
F7
Step Into
F8
Step Over
F9
Debug
Ctrl+F2
Stop Debugger
Ctrl+F5
Add to Watch List
Ctrl+F8
Step Out
Alt+D
Dissasembly View
Shift+F5
Open Watch Window
Ctrl+Shift+A
Show Advanced Breakpoints
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
31
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
IDE OVERVIEW
The mikroPascal PRO for PIC is an user-friendly and intuitive environment:
- The Code Editor features adjustable Syntax Highlighting, Code Folding, Code
Assistant, Parameters Assistant, Spell Checker, Auto Correct for common typos
and Code Templates (Auto Complete).
- The Code Explorer is at your disposal for easier project management.
- The Project Manager alows multiple project management
- General project settings can be made in the Project Settings window
- Library manager enables simple handling libraries being used in a project
- The Error Window displays all errors detected during compiling and linking.
- The source-level Software Simulator lets you debug executable logic step-by-step
by watching the program flow.
-The New Project Wizard is a fast, reliable, and easy way to create a project.
- Help files are syntax and context sensitive.
- Like in any modern Windows application, you may customize the layout of
mikroPascal PRO for PIC to suit your needs best.
- Spell checker underlines identifiers which are unknown to the project. In this way
it helps the programmer to spot potential problems early, much before the project
is compiled.
Spell checker can be disabled by choosing the option in the Preferences dialog (F12).
32
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
CUSTOMIZING IDE LAYOUT
Docking Windows
You can increase the viewing and editing space for code, depending on how you
arrange the windows in the IDE.
Step 1: Click the window you want to dock, to give it focus.
Step 2: Drag the tool window from its current location. A guide diamond appears.
The four arrows of the diamond point towards the four edges of the IDE.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
33
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Step 3: Move the pointer over the corresponding portion of the guide diamond. An
outline of the window appears in the designated area.
Step 4: To dock the window in the position indicated, release the mouse button.
Tip: To move a dockable window without snapping it into place, press CTRL while
dragging it.
Saving Layout
Once you have a window layout that you like, you can save the layout by typing the
name for the layout and pressing the Save Layout Icon
.
To set the layout select the desired layout from the layout drop-down list and click
the Set Layout Icon
.
To remove the layout from the drop-down list, select the desired layout from the list
and click the Delete Layout Icon
34
.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Auto Hide
Auto Hide enables you to see more of your code at one time by minimizing tool windows along the edges of the IDE when not in use.
- Click the window you want to keep visible to give it focus.
- Click the Pushpin Icon
on the title bar of the window.
When an auto-hidden window loses focus, it automatically slides back to its tab on
the edge of the IDE. While a window is auto-hidden, its name and icon are visible
on a tab at the edge of the IDE. To display an auto-hidden window, move your pointer over the tab. The window slides back into view and is ready for use.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
35
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
ADVANCED CODE EDITOR
The Code Editor is advanced text editor fashioned to satisfy needs of professionals.
General code editing is the same as working with any standard text-editor, including
familiar Copy, Paste and Undo actions, common for Windows environment.
Advanced Editor Features
- Adjustable Syntax Highlighting
- Code Assistant
- Code Folding
- Parameter Assistant
- Code Templates (Auto Complete)
- Auto Correct for common typos
- Spell Checker
- Bookmarks and Goto Line
- Comment / Uncomment
You can configure the Syntax Highlighting, Code Templates and Auto Correct from
the Editor Settings dialog. To access the Settings, click Tools › Options from the
drop-down menu, click the Show Options Icon
36
or press F12 key.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Code Assistant
If you type the first few letters of a word and then press Ctrl+Space, all valid identifiers matching the letters you have typed will be prompted in a floating panel (see
the image below). Now you can keep typing to narrow the choice, or you can select
one from the list using the keyboard arrows and Enter.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
37
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Code Folding
Code folding is IDE feature which allows users to selectively hide and display sections of a source file. In this way it is easier to manage large regions of code within
one window, while still viewing only those subsections of the code that are relevant
during a particular editing session.
While typing, the code folding symbols (
and
) appear automatically. Use the
folding symbols to hide/unhide the code subsections.
If you place a mouse cursor over the tooltip box, the collapsed text will be shown in
a tooltip style box.
38
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Parameter Assistant
The Parameter Assistant will be automatically invoked when you open parenthesis
“(” or press Shift+Ctrl+Space. If the name of a valid function precedes the parenthesis, then the expected parameters will be displayed in a floating panel. As you type
the actual parameter, the next expected parameter will become bold.
Code Templates (Auto Complete)
You can insert the Code Template by typing the name of the template (for instance,
whiles), then press Ctrl+J and the Code Editor will automatically generate a code.
You can add your own templates to the list. Select Tools › Options from the drop-down
menu, or click the Show Options Icon
and then select the Auto Complete Tab. Here
you can enter the appropriate keyword, description and code of your template.
Autocomplete macros can retreive system and project information:
-
%DATE% - current system date
%TIME% - current system time
%DEVICE% - device(MCU) name as specified in project settings
%DEVICE_CLOCK% - clock as specified in project settings
%COMPILER% - current compiler version
These macros can be used in template code, see template ptemplate provided with
mikroPascal PRO for PIC installation.
Auto Correct
The Auto Correct feature corrects common typing mistakes. To access the list of recognized typos, select Tools › Options from the drop-down menu, or click the Show
Options Icon
and then select the Auto Correct Tab. You can also add your own
preferences to the list.
Also, the Code Editor has a feature to comment or uncomment the selected code by simple click of a mouse, using the Comment Icon
and Uncomment Icon
from the
Code Toolbar.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
39
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Spell Checker
The Spell Checker underlines unknown objects in the code, so they can be easily
noticed and corrected before compiling your project.
Select Tools › Options from the drop-down menu, or click the Show Options
Icon
and then select the Spell Checker Tab.
Bookmarks
Bookmarks make navigation through a large code easier. To set a bookmark, use
Ctrl+Shift+number. To jump to a bookmark, use Ctrl+number.
Goto Line
The Goto Line option makes navigation through a large code easier. Use the shortcut Ctrl+G to activate this option.
Comment / Uncomment
Also, the Code Editor has a feature to comment or uncomment the selected
code by simple click of a mouse, using the Comment Icon
ment Icon
40
and Uncom-
from the Code Toolbar.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
CODE EXPLORER
The Code Explorer gives clear view of each item declared inside the source code.
You can jump to a declaration of any item by right clicking it. Also, besides the list of
defined and declared objects, code explorer displays message about first error and
it's location in code.
Following options are available in the Code Explorer:
Icon
Description
Expand/Collapse all nodes in tree.
Locate declaration in code.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
41
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
ROUTINE LIST
Routine list diplays list of routines, and enables filtering routines by name. Routine
list window can be accessed by pressing Ctrl+L.
You can jump to a desired routine by double clicking on it.
42
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
PROJECT MANAGER
Project Manager is IDE feature which allows users to manage multiple projects.
Several projects which together make project group may be open at the same time.
Only one of them may be active at the moment.
Setting project in active mode is performed by double click on the desired project
in the Project Manager.
Following options are available in the Project Manager:
Icon
Description
Save project Group.
Open project group.
Close the active project.
Close project group.
Add project to the project group.
Remove project from the project group.
Add file to the active project.
Remove selected file from the project.
Build the active project.
Run mikroElektronika's Flash programmer.
For details about adding and removing files from project see Add/Remove Files from
Project.
Related topics: Project Settings, Project Menu Options, File Menu Options, Project
Toolbar, Build Toolbar, Add/Remove Files from Project
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
43
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
PROJECT SETTINGS WINDOW
Following options are available in the Project Settings Window:
- Device - select the appropriate device from the device drop-down list.
- Oscillator - enter the oscillator frequency value.
- Build/Debugger Type - choose debugger type.
Related topics: Edit Project, Customizing Projects
44
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
LIBRARY MANAGER
Library Manager enables simple handling libraries being used in a project. Library
Manager window lists all libraries (extencion .mcl) which are instantly stored in the
compiler Uses folder. The desirable library is added to the project by selecting check
box next to the library name.
In order to have all library functions accessible, simply press the button Check
All
and all libraries will be selected. In case none library is needed in a
project, press the button Clear All
and all libraries will be cleared from the
project.
Only the selected libraries will be linked.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
45
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Icon
Description
Refresh Library by scanning files in "Uses" folder.Useful when new
libraries are added by copying files to "Uses" folder.
Rebuild all available libraries. Useful when library sources are available and
need refreshing.
Include all available libraries in current project.
No libraries from the list will be included in current project.
Restore library to the state just before last project saving.
Related topics: mikroPascal PRO for PIC Libraries, Creating New Library
ERROR WINDOW
In case that errors were encountered during compiling, the compiler will report them
and won’t generate a hex file. The Error Window will be prompted at the bottom of
the main window by default.
The Error Window is located under message tab, and displays location and type of
errors the compiler has encountered. The compiler also reports warnings, but these
do not affect the output; only errors can interefere with the generation of hex.
Double click the message line in the Error Window to highlight the line where the
error was encountered.
Related topics: Error Messages
46
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
STATISTICS
After successful compilation, you can review statistics of your code. Click the Statistics Icon
.
Memory Usage Windows
Provides overview of RAM and ROM usage in the various forms.
RAM Memory Usage
Displays RAM memory usage in a pie-like form.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
47
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Used RAM Locations
Displays used RAM memory locations and their names.
48
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
SFR Locations
Displays list of used SFR locations.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
49
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
ROM Memory Usage
Displays ROM memory space usage in a pie-like form.
50
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
ROM Memory Constants
Displays ROM memory constants and their addresses.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
51
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Functions Sorted By Name
Sorts and displays functions by their addresses, symbolic names, and unique
assembler names.
52
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Functions Sorted By Size
Sorts and displays functions by their size, in the ascending order.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
53
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Functions Sorted By Addresses
Sorts and displays functions by their addresses, in the ascending order.
54
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Functions Sorted By Name Chart
Sorts and displays functions by their names in a chart-like form.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
55
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Functions Sorted By Size Chart
Sorts and displays functions by their sizes in a chart-like form.
56
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Functions Sorted By Addresses Chart
Sorts and displays functions by their addresses in a chart-like form.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
57
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Function Tree
Displays Function Tree with the relevant data for each function.
58
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Memory Summary
Displays summary of RAM and ROM memory in a pie-like form.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
59
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
INTEGRATED TOOLS
USART Terminal
The mikroPascal PRO for PIC includes the USART communication terminal for
RS232 communication. You can launch it from the drop-down menu Tools › USART
Terminal or by clicking the USART Terminal Icon
60
from Tools toolbar.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
EEPROM Editor
The EEPROM Editor is used for manipulating MCU's EEPROM memory. You can
launch it from the drop-down menu Tools › EEPROM Editor. When Use this
EEPROM definition is checked compiler will generate Intel hex file
project_name.ihex that contains data from EEPROM editor.
When you run mikroElektronika programmer software from mikroPascal PRO for
PIC IDE - project_name.hex file will be loaded automatically while ihex file must be
loaded manually.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
61
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
ASCII Chart
The ASCII Chart is a handy tool, particularly useful when working with Lcd display.
You can launch it from the drop-down menu Tools › ASCII chart or by clicking the
View ASCII Chart Icon
62
from Tools toolbar.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Seven Segment Convertor
The Seven Segment Display Convertor is a convenient visual panel which returns
decimal/hex value for any viable combination you would like to display on 7seg.
Click on the parts of 7 segment image to get the requested value in the edit boxes.
You can launch it from the drop-down menu Tools › Seven Segment Convertor or
by clicking the Seven Segment Icon
from Tools toolbar.
Lcd Custom Character
mikroPascal PRO for PIC includes the Lcd Custom Character. Output is mikroPascal PRO for PIC compatible code. You can launch it from the drop-down menu Tools
› Lcd Custom Character.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
63
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Graphic Lcd Bitmap Editor
The mikroPascal PRO for PIC includes the Graphic Lcd Bitmap Editor. Output is the
mikroPascal PRO for PIC compatible code. You can launch it from the drop-down
menu Tools › Glcd Bitmap Editor.
64
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
HID Terminal
The mikroPascal PRO for PIC includes the HID communication terminal for USB
communication. You can launch it from the drop-down menu Tools › HID Terminal.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
65
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
UDP Terminal
The mikroPascal PRO for PIC includes the UDP Terminal. You can launch it from
the drop-down menu Tools › UDP Terminal.
mikroBootloader
What is a Bootloader
(From Microchip’s document AN732) The PIC16F87X family of microcontrollers has
the ability to write to their own program memory. This feature allows a small bootloader program to receive and write new firmware into memory. In its most simple
form, the bootloader starts the user code running, unless it finds that new firmware
should be downloaded. If there is new firmware to be downloaded, it gets the data
and writes it into program memory. There are many variations and additional features that can be added to improve reliability and simplify the use of the bootloader.
Note: mikroBootloader can be used only with PIC MCUs that support flash write.
66
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
How to use mikroBootloader
1. Load the PIC with the appropriate hex file using the conventional programming
techniques (e.g. for PIC16F877A use p16f877a.hex).
2. Start mikroBootloader from the drop-down menu Tools › Bootoader.
3. Click on Setup Port and select the COM port that will be used. Make sure that
BAUD is set to 9600 Kpbs.
4. Click on Open File and select the HEX file you would like to upload.
5. Since the bootcode in the PIC only gives the computer 4-5 sec to connect, you
should reset the PIC and then click on the Connect button within 4-5 seconds.
6. The last line in then history window should now read “Connected”.
7. To start the upload, just click on the Start Bootloader button.
8. Your program will written to the PIC flash. Bootloader will report an errors that
may occur.
9. Reset your PIC and start to execute.
Features
The boot code gives the computer 5 seconds to get connected to it. If not, it starts
running the existing user code. If there is a new user code to be downloaded, the
boot code receives and writes the data into program memory.
The more common features a bootloader may have are listed below:
-
Code at the Reset location.
Code elsewhere in a small area of memory.
Checks to see if the user wants new user code to be loaded.
Starts execution of the user code if no new user code is to be loaded.
Receives new user code via a communication channel if code is to be loaded.
Programs the new user code into memory.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
67
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Integrating User Code and Boot Code
The boot code almost always uses the Reset location and some additional program
memory. It is a simple piece of code that does not need to use interrupts; therefore,
the user code can use the normal interrupt vector at 0x0004. The boot code must
avoid using the interrupt vector, so it should have a program branch in the address
range 0x0000 to 0x0003. The boot code must be programmed into memory using
conventional programming techniques, and the configuration bits must be programmed at this time. The boot code is unable to access the configuration bits,
since they are not mapped into the program memory space.
68
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
MACRO EDITOR
A macro is a series of keystrokes that have been 'recorded' in the order performed.
A macro allows you to 'record' a series of keystrokes and then 'playback', or repeat,
the recorded keystrokes.
The Macro offers the following commands:
Icon
Description
Starts 'recording' keystrokes for later playback.
Stops capturing keystrokesthat was started when the Start Recordig command was selected.
Allows a macro that has been recorded to be replayed.
New macro.
Delete macro.
Related topics: Advanced Code Editor, Code Templates
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
69
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
OPTIONS
Options menu consists of three tabs: Code Editor, Tools and Output settings
Code editor
The Code Editor is advanced text editor fashioned to satisfy needs of professionals.
Tools
The mikroPascal PRO for PIC includes the Tools tab, which enables the use of
shortcuts to external programs, like Calculator or Notepad.
You can set up to 10 different shortcuts, by editing Tool0 - Tool9.
70
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Output settings
By modifying Output Settings, user can configure the content of the output files.
You can enable or disable, for example, generation of ASM and List file.
Also, user can choose optimization level, and compiler specific settings, which
include case sensitivity, dynamic link for string literals setting (described in
mikroPascal PRO for PIC specifics).
Build all files as library enables user to use compiled library (*.mcl) on any PIC
MCU (when this box is checked), or for a selected PIC MCU (when this box is left
unchecked).
For more information on creating new libraries, see Creating New Library.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
71
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
REGULAR EXPRESSIONS
Introduction
Regular Expressions are a widely-used method of specifying patterns of text to
search for. Special metacharacters allow you to specify, for instance, that a particular string you are looking for, occurs at the beginning, or end of a line, or contains n
recurrences of a certain character.
Simple matches
Any single character matches itself, unless it is a metacharacter with a special
meaning described below. A series of characters matches that series of characters
in the target string, so the pattern "short" would match "short" in the target string.
You can cause characters that normally function as metacharacters or escape
sequences to be interpreted by preceding them with a backslash "\".
For instance, metacharacter "^" matches beginning of string, but "\^" matches character "^", and "\\" matches "\", etc.
Examples :
unsigned matches string 'unsigned'
\^unsigned matches string '^unsigned'
Escape sequences
Characters may be specified using a escape sequences: "\n" matches a newline,
"\t" a tab, etc. More generally, \xnn, where nn is a string of hexadecimal digits,
matches the character whose ASCII value is nn.
If you need wide (Unicode) character code, you can use '\x{nnnn}', where 'nnnn'
- one or more hexadecimal digits.
\xnn - char with hex code nn
\x{nnnn)- char with hex code nnnn (one byte for plain text and two bytes for Unicode)
\t - tab (HT/TAB), same as \x09
\n - newline (NL), same as \x0a
\r - car.return (CR), same as \x0d
\f - form feed (FF), same as \x0c
\a - alarm (bell) (BEL), same as \x07
\e - escape (ESC) , same as \x1b
Examples:
unsigned\x20int matches 'unsigned int' (note space in the middle)
\tunsigned matches 'unsigned' (predecessed by tab)
72
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Character classes
You can specify a character class, by enclosing a list of characters in [], which will
match any of the characters from the list. If the first character after the "[" is "^",
the class matches any character not in the list.
Examples:
count[aeiou]r finds strings 'countar', 'counter', etc. but not 'countbr', 'countcr', etc.
count[^aeiou]r finds strings 'countbr', 'countcr', etc. but not 'countar', 'counter', etc.
Within a list, the "-" character is used to specify a range, so that a-z represents all
characters between "a" and "z", inclusive.
If you want "-" itself to be a member of a class, put it at the start or end of the list,
or precede it with a backslash.
If you want ']', you may place it at the start of list or precede it with a backslash.
Examples:
[-az] matches 'a', 'z' and '-'
[az-] matches 'a', 'z' and '-'
[a\-z] matches 'a', 'z' and '-'
[a-z] matches all twenty six small characters from 'a' to 'z'
[\n-\x0D] matches any of #10,#11,#12,#13.
[\d-t] matches any digit, '-' or 't'.
[]-a] matches any char from ']'..'a'.
Metacharacters
Metacharacters are special characters which are the essence of regular expressions. There are different types of metacharacters, described below.
Metacharacters - Line separators
^ - start of line
$ - end of line
\A - start of text
\Z - end of text
. - any character in line
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
73
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Examples:
^PORTA - matches string ' PORTA ' only if it's at the beginning of line
PORTA$ - matches string ' PORTA ' only if it's at the end of line
^PORTA$ - matches string ' PORTA ' only if it's the only string in line
PORT.r - matches strings like 'PORTA', 'PORTB', 'PORT1' and so on
The "^" metacharacter by default is only guaranteed to match beginning of the input
string/text, and the "$" metacharacter only at the end. Embedded line separators
will not be matched by ^" or "$".
You may, however, wish to treat a string as a multi-line buffer, such that the "^" will
match after any line separator within the string, and "$" will match before any line
separator.
Regular expressions works with line separators as recommended at http://www.unicode.org/unicode/reports/tr18/
Metacharacters - Predefined classes
\w
\W
\d
\D
\s
\S
-
an alphanumeric character (including "_")
a nonalphanumeric character
a numeric character
a non-numeric character
any space (same as [\t\n\r\f])
a non space
You may use \w, \d and \s within custom character classes.
Example:
routi\de - matches strings like 'routi1e', 'routi6e' and so on, but not 'routine',
'routime' and so on.
Metacharacters - Word boundaries
A word boundary ("\b") is a spot between two characters that has an alphanumeric character ("\w") on one side, and a nonalphanumeric character ("\W") on the
other side (in either order), counting the imaginary characters off the beginning and
end of the string as matching a "\W".
\b - match a word boundary)
\B - match a non-(word boundary)
74
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Metacharacters - Iterators
Any item of a regular expression may be followed by another type of metacharacters - iterators. Using this metacharacters,you can specify number of occurences of
previous character, metacharacter or subexpression.
* - zero or more ("greedy"), similar to {0,}
+ - one or more ("greedy"), similar to {1,}
? - zero or one ("greedy"), similar to {0,1}
{n} - exactly n times ("greedy")
{n,} - at least n times ("greedy")
{n,m} - at least n but not more than m times ("greedy")
*? - zero or more ("non-greedy"), similar to {0,}?
+? - one or more ("non-greedy"), similar to {1,}?
?? - zero or one ("non-greedy"), similar to {0,1}?
{n}? - exactly n times ("non-greedy")
{n,}? - at least n times ("non-greedy")
{n,m}? - at least n but not more than m times ("non-greedy")
So, digits in curly brackets of the form, {n,m}, specify the minimum number of times
to match the item n and the maximum m. The form {n} is equivalent to {n,n} and
matches exactly n times. The form {n,} matches n or more times. There is no limit
to the size of n or m, but large numbers will chew up more memory and slow down
execution.
If a curly bracket occurs in any other context, it is treated as a regular character.
Examples:
count.*r ß- matches strings like 'counter', 'countelkjdflkj9r' and 'countr'
count.+r - matches strings like 'counter', 'countelkjdflkj9r' but not 'countr'
count.?r - matches strings like 'counter', 'countar' and 'countr' but not 'countelkj9r'
counte{2}r - matches string 'counteer'
counte{2,}r - matches strings like 'counteer', 'counteeer', 'counteeer' etc.
counte{2,3}r - matches strings like 'counteer', or 'counteeer' but not 'counteeeer'
A little explanation about "greediness". "Greedy" takes as many as possible, "nongreedy" takes as few as possible.
For example, 'b+' and 'b*' applied to string 'abbbbc' return 'bbbb', 'b+?'
returns 'b', 'b*?' returns empty string, 'b{2,3}?' returns 'bb', 'b{2,3}'
returns 'bbb'.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
75
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Metacharacters - Alternatives
You can specify a series of alternatives for a pattern using "|" to separate them, so
that bit|bat|bot will match any of "bit", "bat", or "bot" in the target string as
would "b(i|a|o)t)". The first alternative includes everything from the last pattern
delimiter ("(", "[", or the beginning of the pattern) up to the first "|", and the last
alternative contains everything from the last "|" to the next pattern delimiter. For this
reason, it's common practice to include alternatives in parentheses, to minimize
confusion about where they start and end.
Alternatives are tried from left to right, so the first alternative found for which the
entire expression matches, is the one that is chosen. This means that alternatives
are not necessarily greedy. For example: when matching rou|rout against "routine", only the "rou" part will match, as that is the first alternative tried, and it successfully matches the target string (this might not seem important, but it is important
when you are capturing matched text using parentheses.) Also remember that "|"
is interpreted as a literal within square brackets, so if you write [bit|bat|bot],
you're really only matching [biao|].
Examples:
rou(tine|te) - matches strings 'routine' or 'route'.
Metacharacters - Subexpressions
The bracketing construct ( ... ) may also be used for define regular subexpressions.
Subexpressions are numbered based on the left to right order of their opening
parenthesis. First subexpression has number '1'
Examples:
(int){8,10} matches strings which contain 8, 9 or 10 instances of the 'int'
routi([0-9]|a+)e matches 'routi0e', 'routi1e' , 'routine', 'routinne',
'routinnne' etc.
Metacharacters - Backreferences
Metacharacters \1 through \9 are interpreted as backreferences. \ matches previously matched subexpression #.
Examples:
(.)\1+ matches 'aaaa' and 'cc'.
(.+)\1+ matches 'abab' and '123123'
(['"]?)(\d+)\1 matches "13" (in double quotes), or '4' (in single quotes) or 77
(without quotes) etc
76
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
MIKROPASCAL PRO FOR PIC COMMAND LINE OPTIONS
Usage: mPPIC.exe [-<opts> [-<opts>]] [<infile> [-<opts>]] [-<opts>]]
Infile can be of *.mpas and *.mcl type.
The following parameters and some more (see manual) are valid:
-P : MCU for which compilation will be done.
-FO : Set oscillator [in MHz].
-SP : Add directory to the search path list.
-N : Output files generated to file path specified by filename.
-B : Save compiled binary files (*.mcl) to 'directory'.
-O : Miscellaneous output options.
-DBG : Generate debug info.
-L : Check and rebuild new libraries.
-DL : Build all files as libraries.
-Y : Dynamic link for string literals.
-UICD : ICD build type.
Example:
mPPIC.exe
-MSF
-DBG
-p16F887
-O11111114
-fo8
N"C:\Lcd\Lcd.mpppi"
-SP"C:\Program
Files\Mikroelektronika\mikroPascal PRO for PIC\Defs\"
-SP"C:\Program Files\Mikroelektronika\mikroPascal PRO
for
PIC\Uses\P16\"
-SP"C:\Lcd\"
"Lcd.mpas"
"__Lib_Math.mcl"
"__Lib_MathDouble.mcl"
"__Lib_System.mcl" "__Lib_Delays.mcl"
"__Lib_LcdConsts.mcl" "__Lib_Lcd.mcl"
Parameters used in the example:
-MSF : Short Message Format; used for internal purposes by IDE.
-DBG : Generate debug info.
-p16F887 : MCU 16F887 selected.
-O11111114 : Miscellaneous output options.
-fo8 : Set oscillator frequency [in MHz].
-N"C:\Lcd\Lcd.mpppi" -SP"C:\Program Files\Mikroelektronika\mikroPascal PRO for PIC\defs\" : Output files generated to file path specified by
filename.
-SP"C:\Program Files\Mikroelektronika\mikroPascal PRO for PIC\Defs\"
: Add directory to the search path list.
-SP"C:\Program
Files\Mikroelektronika\mikroPascal
PRO
for
PIC\Uses\P16\" : Add directory to the search path list.
-SP"C:\Lcd\" : Add directory to the search path list.
"Lcd.mpas"
"__Lib_Math.mcl"
"__Lib_MathDouble.mcl"
"__Lib_System.mcl"
"__Lib_Delays.mcl"
"__Lib_LcdConsts.mcl"
"__Lib_Lcd.mcl" : Specify input files.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
77
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
PROJECTS
The mikroPascal PRO for PIC organizes applications into projects, consisting of a
single project file (extension .mpppi) and one or more source files (extension mpas).
mikroPascal PRO for PIC IDE allows you to manage multiple projects (see Project
Manager). Source files can be compiled only if they are part of a project.
The project file contains the following information:
-
project name and optional description,
target device,
device flags (config word),
device clock,
list of the project source files with paths,
image files,
other files.
Note that the project does not include files in the same way as preprocessor does,
see Add/Remove Files from Project.
New Project
The easiest way to create a project is by means of the New Project Wizard, dropdown menu Project › New Project or by clicking the New Project Icon
from
Project Toolbar.
78
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
New Project Wizard Steps
Start creating your New project, by clicking Next button:
Step One - Select the device from the device drop-down list.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
79
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Step Two - Enter the oscillator frequency value.
Step Three - Specify the location where your project will be saved.
80
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Step Four - Add project file to the project if they are avaiable at this point. You can
always add project files later using Project Manager.
Step Five - Click Finish button to create your New Project:
Related topics: Project Manager, Project Settings
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
81
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
CUSTOMIZING PROJECTS
You can change basic project settings in the Project Settings window, like chip and
oscillator frequency. Any change in the Project Setting Window affects currently
active project only, so in case more than one project is open, you have to ensure
that exactly the desired project is set as active one in the Project Manager. Also, you
can change configuration bits of the selected chip in the Edit Project window.
Managing Project Group
mikroPascal PRO for PIC IDE provides covenient option which enables several projects to be open simultaneously. If you have several projects being connected in
some way, you can create a project group.
The project group may be saved by clicking the Save Project Group Icon
from
the Project Manager window. The project group may be reopend by clicking the
Open Project Group Icon
. All relevant data about the project group is stored in
the project group file (extension .mpg)
ADD/REMOVE FILES FROM PROJECT
The project can contain the following file types:
.mpas source files
.mcl binary files
.pld project level defines files
image files
.hex, .asm and .lst files, see output files. These files can not be added or
removed from project.
other files
82
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
The list of relevant source files is stored in the project file (extension .mpppi).
To add source file to the project, click the Add File to Project Icon
. Each added
source file must be self-contained, i.e. it must have all necessary definitions after
preprocessing.
To remove file(s) from the project, click the Remove File from Project Icon
.
See File Inclusion for more information.
Project Level Defines
Project Level Defines (.pld) files can also be added to project. Project level define
files enable you to have defines that are visible in all source files in the project. One
project may contain several pld files. A file must contain one definition per line, for
example:
ANALOG
DEBUG
TEST
There are some predefined project level defines. See predefined project level
defines
Related topics: Project Manager, Project Settings, Edit Project
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
83
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
SOURCE FILES
Source files containing Pascal code should have the extension .mpas. The list of
source files relevant to the application is stored in project file with extension .mpppi,
along with other project information. You can compile source files only if they are
part of the project.
Managing Source Files
Creating new source file
To create a new source file, do the following:
1. Select File › New Unit from the drop-down menu, or press Ctrl+N, or click the
New File Icon
from the File Toolbar.
2. A new tab will be opened. This is a new source file. Select File › Save from the
drop-down menu, or press Ctrl+S, or click the Save File Icon
from the File
Toolbar and name it as you want.
If you use the New Project Wizard, an empty source file, named after the project with
extension .mpas, will be created automatically. The mikroPascal PRO for PIC does
not require you to have a source file named the same as the project, it’s just a matter of convenience.
Opening an existing file
1. Select File › Open from the drop-down menu, or press Ctrl+O, or click the Open
File Icon
from the File Toolbar. In Open Dialog browse to the location of the
file that you want to open, select it and click the Open button.
2. The selected file is displayed in its own tab. If the selected file is already open, its
current Editor tab will become active.
Printing an open file
1. Make sure that the window containing the file that you want to print is the active
window.
2 Select File › Print from the drop-down menu, or press Ctrl+P.
3. In the Print Preview Window, set a desired layout of the document and click the
OK button. The file will be printed on the selected printer.
84
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Saving file
1. Make sure that the window containing the file that you want to save is the active
window.
2. Select File › Save from the drop-down menu, or press Ctrl+S, or click the Save
File Icon
from the File Toolbar.
Saving file under a different name
1. Make sure that the window containing the file that you want to save is the active
window.
2. Select File › Save As from the drop-down menu. The New File Name dialog will
be displayed.
3. In the dialog, browse to the folder where you want to save the file.
4. In the File Name field, modify the name of the file you want to save.
5. Click the Save button.
Closing file
1. Make sure that the tab containing the file that you want to close is the active tab.
2. Select File › Close from the drop-down menu, or right click the tab of the file that
you want to close and select Close option from the context menu.
3. If the file has been changed since it was last saved, you will be prompted to save
your changes.
Related topics:File Menu, File Toolbar, Project Manager, Project Settings,
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
85
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
CLEAN PROJECT FOLDER
This menu gives you option to choose which files from your current project you want
to delete.
Files marked in bold can be easily recreated by building a project. Other files should
be marked for deletion only with a great care, because IDE cannot recover them.
Related topics: Customizing Projects
86
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
COMPILATION
When you have created the project and written the source code, it's time to compile
it. Select Project › Build from the drop-down menu, or click the Build Icon
from
the Project Toolbar. If more more than one project is open you can compile all open
projects by selecting Project › Build All from the drop-down menu, or click the Build
All Icon
from the Project Toolbar.
Progress bar will appear to inform you about the status of compiling. If there are
some errors, you will be notified in the Error Window. If no errors are encountered,
the mikroPascal PRO for PIC will generate output files.
Output Files
Upon successful compilation, the mikroPascal PRO for PIC will generate output files
in the project folder (folder which contains the project file .mpppi). Output files are
summarized in the table below:
Format
Description
File Type
Intel HEX
Intel style hex records. Use this file to program
PIC MCU.
.hex
Binary
mikro Compiled Library. Binary distribution of
application that can be included in other projects.
.mcl
List File
Overview of PIC memory allotment: instruction
addresses, registers, routines and labels.
.lst
Assembler File
Human readable assembly with symbolic names,
extracted from the List File.
.asm
ASSEMBLY VIEW
After compiling the program in the mikroPascal PRO for PIC, you can click the View
Assembly icon
or select Project › View Assembly from the drop-down menu
to review the generated assembly code (.asm file) in a new tab window. Assembly
is human-readable with symbolic names.
Related topics:Project Menu, Project Toolbar, Error Window, Project Manager, Project Settings
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
87
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
ERROR MESSAGES
Compiler Error Messages:
- "%s" is not valid identifier.
- Unknown type "%s".
- Identifier "%s" was not declared.
- Syntax error: Expected "%s" but "%s" found.
- Argument is out of range "%s".
- Syntax error in additive expression.
- File "%s" not found.
- Invalid command "%s".
- Not enough parameters.
- Too many parameters.
- Too many characters.
- Actual and formal parameters must be identical.
- Invalid ASM instruction: "%s".
- Identifier "%s" has been already declared in "%s".
- Syntax error in multiplicative expression.
- Definition file for "%s" is corrupted.
- ORG directive is currently supported for interrupts only.
- Not enough ROM.
- Not enough RAM.
- External procedure "%s" used in "%s" was not found.
- Internal error: "%s".
- Unit cannot recursively use itself.
- "%s" cannot be used out of loop.
- Actual and formal parameters do not match ("%s" to "%s").
- Constant cannot be assigned to.
- Constant array must be declared as global.
- Incompatible types ("%s" to "%s").
- Too many characters ("%s").
- Soft_Uart cannot be initialized with selected baud rate/device clock.
- Main label cannot be used in modules.
- Break/Continue cannot be used out of loop.
- Preprocessor Error: "%s".
- Expression is too complicated.
- Duplicated label "%s".
- Complex type cannot be declared here.
- Record is empty.
- Unknown type "%s".
- File not found "%s".
- Constant argument cannot be passed by reference.
- Pointer argument cannot be passed by reference.
88
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
- Operator "%s" not applicable to these operands "%s".
- Exit cannot be called from the main block.
- Complex type parameter must be passed by reference.
- Error occured while compiling "%s".
- Recursive types are not allowed.
- Adding strings is not allowed, use "strcat" procedure instead.
- Cannot declare pointer to array, use pointer to structure which has array field.
- Return value of the function "%s" is not defined.
- Assignment to for loop variable is not allowed.
- "%s" is allowed only in the main program.
- Start address of "%s" has already been defined.
- Simple constant cannot have fixed address.
- Invalid date/time format.
- Invalid operator "%s".
- File "%s" is not accessible.
- Forward routine "%s" is missing implementation.
- ";" is not allowed before "else".
- Not enough elements: expected "%s", but "%s" elements found.
- Too many elements: expected "%s" elements.
- "external" is allowed for global declarations only.
- Destination size ("%s") does not match source size ("%s").
- Routine prototype is different from previous declaration.
- Division by zero.
- Uart module cannot be initialized with selected baud rate/device clock.
- "%s" cannot be of "%s" type.
- Array of "%s" can not be declared.
- Incomplete variable declaration: "%s".
- Recursive build of units is not allowed (""%s"").
- Object must be smaller than 64kb in size: ""%s"".
- Index out of bounds.
- With statment cannot be used with this argument ""%s"".
- Reset directive is available only on P18 family.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
89
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Warning Messages:
- Variable "%s" is not initialized.
- Return value of the function "%s" is not defined.
- Identifier "%s" overrides declaration in unit "%s".
- Generated baud rate is %s bps (error = %s percent).
- Result size may exceed destination array size.
- Infinite loop.
- Implicit typecast performed from "%s" to "%s".
- Implicit typecast of integral value to pointer.
- Library "%s" was not found in search path.
- Interrupt context saving has been turned off.
- Source size (%s) does not match destination size (%s).
- Aggregate padded with zeros (%s) in order to match declared size (%s).
- Suspicious pointer conversion.
- Source size may exceed destination size.
HINT MESSAGES:
-
90
Constant "%s" has been declared, but not used.
Variable "%s" has been declared, but not used.
Unit "%s" has been recompiled.
Variable "%s" has been eliminated by optimizer.
Compiling unit "%s".
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
SOFTWARE SIMULATOR OVERVIEW
The Source-level Software Simulator is an integral component of the mikroPascal
PRO for PIC environment. It is designed to simulate operations of the PIC MCUs
and assist the users in debugging Pascal code written for these devices.
Upon completion of writing your program, choose Release build Type in the Project
Settings window:
After you have successfully compiled your project, you can run the Software Simulator by selecting Run › Start Debugger from the drop-down menu, or by clicking
the Start Debugger Icon
from the Debugger Toolbar. Starting the Software Sim-
ulator makes more options available: Step Into, Step Over, Step Out, Run to Cursor,
etc. Line that is to be executed is color highlighted (blue by default).
Note: The Software Simulator simulates the program flow and execution of instruction lines, but it cannot fully emulate PIC device behavior, i.e. it doesn’t update
timers, interrupt flags, etc.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
91
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Breakpoints Window
The Breakpoints window manages the list of currently set breakpoints in the project.
Doubleclicking the desired breakpoint will cause cursor to navigate to the corresponding location in source code.
Watch Window
The Software Simulator Watch Window is the main Software Simulator window which
allows you to monitor program items while simulating your program. To show the Watch
Window, select View › Debug Windows › Watch from the drop-down menu.
The Watch Window displays variables and registers of the MCU, along with their
addresses and values.
There are two ways of adding variable/register to the watch list:
- by its real name (variable's name in Pascal code). Just select desired variable/register
from Select variable from list drop-down menu and click the Add Button
.
- by its name ID (assembly variable name). Simply type name ID of the variable/register
you want to display into Search the variable by assemby name box and click the Add
Button
.
Variables can also be removed from the Watch window, just select the variable that
you want to remove and then click the Remove Button
Add All Button
Remove All Button
92
.
adds all variables.
removes all variables.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
You can also expand/collapse complex variables, i.e. struct type variables, strings...
Values are updated as you go through the simulation. Recently changed items are
colored red.
Double clicking a variable or clicking the Properties Button
opens
the Edit Value window in which you can assign a new value to the selected
variable/register. Also, you can choose the format of variable/register representation
between decimal, hexadecimal, binary, float or character. All representations except
float are unsigned by default. For signed representation click the check box next to
the Signed label.
An item's value can be also changed by double clicking item's value field and typing
the new value directly.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
93
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
View RAM Window
Debugger View RAM Window is available from the drop-down menu, View › Debug
Windows › View RAM.
The View RAM Window displays the map of PIC’s RAM, with recently changed
items colored red.
94
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Stopwatch Window
The Software Simulator Stopwatch Window is available from the drop-down menu,
View › Debug Windows › Stopwatch.
The Stopwatch Window displays a current count of cycles/time since the last Software Simulator action. Stopwatch measures the execution time (number of cycles)
from the moment Software Simulator has started and can be reset at any time. Delta
represents the number of cycles between the lines where Software Simulator action
has started and ended.
Note: The user can change the clock in the Stopwatch Window, which will recalculate values for the latest specified frequency. Changing the clock in the Stopwatch
Window does not affect actual project settings – it only provides a simulation.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
95
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
SOFTWARE SIMULATOR OPTIONS
Format
Description
File Type
Start
Debugger
Start Software Simulator.
[F9]
Run/Pause
Debugger
Run or pause Software Simulator.
[F6]
Stop
Debugger
Stop Software Simulator.
Toggle breakpoint at the current cursor position. To
view all breakpoints, select Run > View BreakToggle
points from the drop–down menu. Double clicking
Breakpoints
an item in the Breakpoints Window List locates the
breakpoint.
Toolbar
Icon
[Ctrl+F2]
[F5]
Run to
cursor
Execute all instructions between the current
instruction and cursor position.
[F4]
Step Into
Execute the current Pascal (single or multi–cycle)
instruction, then halt. If the instruction is a routine
call, enter the routine and halt at the first instruction following the call.
[F7]
Step Over
Execute the current Pascal (single or multi–cycle)
instruction, then halt.
[F8]
Step Out
Execute all remaining instructions in the current
routine, return and then halt.
[Ctrl+F8]
Related topics: Run Menu, Debug Toolbar
96
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
CREATING NEW LIBRARY
mikroPascal PRO for PIC allows you to create your own libraries. In order to create
a library in mikroPascal PRO for PIC follow the steps bellow:
1. Create a new Pascal source file, see Managing Source Files
2. Save the file in one of the subfolders of the compiler's Uses folder:
DriveName:\Program Files\Mikroelektronika\mikroPascal PRO for
PIC\Uses\P16\
DriveName:\Program Files\Mikroelektronika\mikroPascal PRO for
PIC\Uses\P18\
If you are creating library for PIC16 MCU family the file should be saved in P16 folder.
If you are creating library for PIC18 MCU family the file should be saved in P18 folder.
If you are creating library for PIC16 and PIC18 MCU families the file should be
saved in both folders.
3. Write a code for your library and save it.
4. Add __Lib_Example file in some project, see Project Manager. Recompile the
project.
If you wish to use this library for all MCUs, then you should go to Tools › Options
› Output settings, and check Build all files as library box.
This will build libraries in a common form which will work with all MCUs. If this box
is not checked, then library will be built for selected MCU.
Bear in mind that compiler will report an error if a library built for specific MCU is
used for another one.
5. Compiled file __Lib_Example.mcl should appear in ...\mikroPascal PRO
for PIC\Uses\P16\ folder.
6. Open the definition file for the MCU that you want to use. This file is placed in the
compiler's Defs folder:
DriveName:\Program Files\Mikroelektronika\mikroPascal PRO for
PIC\Defs\ and it is named MCU_NAME.mlk, for example 16F887.mlk
7. Add the the following segment of code to <LIBRARIES> node of the definition file
(definition file is in XML format):
<LIB>
<ALIAS>Example_Library</ALIAS>
<FILE>__Lib_Example</FILE>
<TYPE>REGULAR</TYPE>
</LIB>
8. Add Library to mlk file for each MCU that you want to use with your library.
9. Click Refresh button in Library Manager
10. Example_Library should appear in the Library manager window.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
97
CHAPTER 2
mikroPASCAL PRO for PIC
Environment
Multiple Library Versions
Library Alias represents unique name that is linked to corresponding Library .mcl
file. For example UART library for 16F887 is different from UART library for 18F4520
MCU. Therefore, two different UART Library versions were made, see mlk files for
these two MCUs. Note that these two libraries have the same Library Alias (UART)
in both mlk files. This approach enables you to have identical representation of
UART library for both MCUs in Library Manager.
Related topics: Library Manager, Project Manager, Managing Source Files
98
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER
3
mikroICD
(In-Circuit Debugger)
mikroICD is highly effective tool for Real-Time debugging on hardware level. ICD
debugger enables you to execute a mikroPascal program on a host PIC microcontroller and view variable values, Special Function Registers (SFR), memory and
EEPROM as the program is running.
99
CHAPTER 3
mikroICD
mikroPASCAL PRO for PIC
If you have appropriate hardware and software for using mikroICD, then, upon completion of writing your program, you will have to choose ICD Debug build type.
You can run the mikroICD by selecting Run › Debug from the drop-down menu, or
by clicking Debug Icon
. Starting the Debugger makes more options available:
Step Into, Step Over, Run to Cursor, etc. Line that is to be executed is color highlighted (blue by default). There is also notification about program execution and it
can be found on Watch Window (yellow status bar). Note that some functions take
time to execute, so running of program is indicated on Watch Window.
100
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 3
mikroPASCAL PRO for PIC
mikroICD
MIKROICD DEBUGGER OPTIONS
Name
Description
Function
Key
Debug
Starts Debugger.
[F9]
Run/ Pause
Debugger
Run or pause Debugger.
[F6]
Toggle
Breakpoints
Toggle breakpoint at the current cursor position. To
view all the breakpoints, select Run › View Breakpoints from the drop-down menu. Double clicking an
item in window list locates the breakpoint.
[F5]
Run to cursor
Execute all instructions between the current
instruction and the cursor position.
[F4]
Step Into
Execute the current C (single– or multi–cycle)
instruction, then halt. If the instruction is a routine
call, enter the routine and halt at the first instruction following the call.
[F7]
Step Over
Execute the current C (single– or multi–cycle)
instruction, then halt. If the instruction is a routine
call, skip it and halt at the first instruction following the call.
[F8]
Flush RAM
Flushes current PIC RAM. All variable values will be
changed according to values from watch window.
N/A
Disassembly
View
Toggle between disassembly and Pascal source
view.
[Alt+D]
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
101
CHAPTER 3
mikroPASCAL PRO for PIC
mikroICD
MIKROICD DEBUGGER EXAMPLE
Here is a step by step mikroICD Debugger Example.
First you have to write a program. We will show how mikroICD works using this
example:
program Lcd_Demo;
var
var
var
var
var
var
LCD_RS
LCD_EN
LCD_D4
LCD_D5
LCD_D6
LCD_D7
var
var
var
var
var
var
LCD_RS_Direction
LCD_EN_Direction
LCD_D4_Direction
LCD_D5_Direction
LCD_D6_Direction
LCD_D7_Direction
:
:
:
:
:
:
sbit
sbit
sbit
sbit
sbit
sbit
at
at
at
at
at
at
RB4_bit;
RB5_bit;
RB0_bit;
RB1_bit;
RB2_bit;
RB3_bit;
:
:
:
:
:
:
sbit
sbit
sbit
sbit
sbit
sbit
at
at
at
at
at
at
TRISB4_bit;
TRISB5_bit;
TRISB0_bit;
TRISB1_bit;
TRISB2_bit;
TRISB3_bit;
var text : array[16] of char;
i : byte;
begin
PORTB := 0;
TRISB := 0;
ANSEL := 0;
ANSELH := 0;
text := 'mikroElektronika';
Lcd_Init();
Lcd_Cmd(_LCD_CLEAR);
Lcd_Cmd(_LCD_CURSOR_OFF);
for i := 1 to 17 do
Lcd_Chr(1, i, text[i-1]);
end.
102
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 3
mikroPASCAL PRO for PIC
mikroICD
After successful compilation and PIC programming press F9 for starting mikroICD.
After mikroICD initialization blue active line should appear.
We will debug program line by line. Pressing F8 we are executing code line by line.
It is recommended that user does not use Step Into [F7] and Step Over [F8] over
Delays routines and routines containing delays. Instead use Run to cursor [F4] and
Breakpoints functions.
All changes are read from PIC and loaded into Watch Window. Note that TRISB
changed its value from 255 to 0.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
103
CHAPTER 3
mikroICD
mikroPASCAL PRO for PIC
Step Into [F7] and Step Over [F8] are mikroICD debugger functions that are used in
stepping mode. There is also Real-Time mode supported by mikro ICD. Functions
that are used in Real-Time mode are Run/ Pause Debugger [F6] and Run to cursor
[F4]. Pressing F4 goes to line selected by user. User just have to select line with cursor and press F4, and code will be executed until selected line is reached.
Run(Pause) Debugger [F6] and Toggle Breakpoints [F5] are mikroICD debugger
functions that are used in Real-Time mode. Pressing F5 marks line selected by user
for breakpoint. F6 executes code until breakpoint is reached. After reaching breakpoint Debugger halts. Here at our example we will use breakpoints for writing
"mikroElektronika" on Lcd char by char. Breakpoint is set on Lcd_Chr and program
will stop everytime this function is reached. After reaching breakpoint we must press
F6 again for continuing program execution.
104
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 3
mikroPASCAL PRO for PIC
mikroICD
Breakpoints has been separated into two groups. There are hardware and software
break points. Hardware breakpoints are placed in PIC and they provide fastest
debug. Number of hardware breakpoints is limited (1 for P16 and 1 or 3 or 5 for
P18). If all hardware brekpoints are used, next breakpoints that will be used are software breakpoint. Those breakpoints are placed inside mikro ICD, and they simulate
hardware breakpoints. Software breakpoints are much slower than hardware breakpoints. This differences between hardware and software differences are not visible
in mikroICD software but their different timings are quite notable, so it is important
to know that there is two types of breakpoints.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
105
CHAPTER 3
mikroPASCAL PRO for PIC
mikroICD
MIKROICD (IN-CIRCUIT DEBUGGER) OVERVIEW
Breakpoints Window
The Breakpoints window manages the list of currently set breakpoints in the project.
Doubleclicking the desired breakpoint will cause cursor to navigate to the corresponding location in source code.
Watch Window
Debugger Watch Window is the main Debugger window which allows you to monitor program items while running your program. To show the Watch Window, select
View › Debug Windows › Watch Window from the drop-down menu.
The Watch Window displays variables and registers of PIC, with their addresses and
values. Values are updated as you go through the simulation. Use the drop-down
menu to add and remove the items that you want to monitor. Recently changed
items are colored red.
106
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 3
mikroPASCAL PRO for PIC
mikroICD
Double clicking an item opens the Edit Value window in which you can assign a new
value to the selected variable/register. Also, you can change view to binary, hex,
char, or decimal for the selected item.
EEPROM Watch Window
mikroICD EEPROM Watch Window is available from the drop-down menu, View ›
Debug Windows › View EEPROM.
The EEPROM Watch window shows current values written into PIC internal
EEPROM memory. There are two action buttons concerning EEPROM Watch window - Write EEPROM and Read EEPROM. Write EEPROM writes data from
EEPROM Watch window into PIC internal EEPROM memory. Read EEPROM reads
data from PIC internal EEPROM memory and loads it up in EEPROM window.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
107
CHAPTER 3
mikroPASCAL PRO for PIC
mikroICD
Code Watch Window
mikroICD Code Watch Window is available from the drop-down menu, View ›
Debug Windows › View Code.
The Code Watch window shows code (hex code) written into PIC. There is action
button concerning Code Watch window - Read Code. Read Code reads code from
PIC and loads it up in View Code Window.
Also, you can set an address scope in which hex code will be read.
108
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 3
mikroPASCAL PRO for PIC
mikroICD
View RAM Window
Debugger View RAM Window is available from the drop-down menu, View › Debug
Windows › View RAM.
The View RAM Window displays the map of PIC’s RAM, with recently changed
items colored red.
Common Errors
- Trying to program PIC while mikroICD is active.
- Trying to debug Release build Type version of program.
- Trying to debug changed program code which hasn't been compiled and programmed into PIC.
- Trying to select line that is empty for Run to cursor [F4] and Toggle Breakpoints
[F5] functions.
- Trying to debug PIC with mikroICD while Watch Dog Timer is enabled.
- Trying to debug PIC with mikroICD while Power Up Timer is enabled.
- It is not possible to force Code Protect while trying to debug PIC with mikroICD.
- Trying to debug PIC with ICD with pull-up resistors set to ON on RB6 and RB7.
- For correct mikroICD debugging do not use pull-ups.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
109
CHAPTER 3
mikroPASCAL PRO for PIC
mikroICD
MIKROICD ADVANCED BREAKPOINTS
mikroICD provides the possibility to use the Advanced Breakpoints. Advanced
Breakpoints can be used with PIC18 and PIC18FJ MCUs. To enable Advanced
Breakpoints set the Advanced Breakpoints checkbox inside Watch window :
To configure Advanced Breakpoints, start mikroICD [F9] and select View › Debug
Windows › Advanced Breakpoints option from the drop-down menu or use
[Ctrl+Shift+A] shortcut.
Note: When Advanced Breakpoints are enabled mikroICD operates in Real-Time
mode, so it will support only the following set of commands: Start Debugger [F9],
Run/Pause Debugger [F6] and Stop Debugger [Ctrl+F2]. Once the Advanced
Breakpoint is reached, the Advanced Breakpoints feature can be disabled and
mikroICD debugging can be continued with full set of commands. If needed,
Advanced Breakepoints can be re-enabled without restarting mikroICD.
Note: Number of Advanced Breakpoints is equal to number of Hardware breakpoints and it depends on used MCU.
110
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 3
mikroPASCAL PRO for PIC
mikroICD
Program Memory Break
Program Memory Break is used to set the Advanced Breakpoint to the specific
address in program memory. Because of PIC pipelining mechanism program execution may stop one or two instructions after the address entered in the Address
field. Value entered in the Address field must be in hex format.
Note: Program Memory Break can use the Passcount option. The program execution will stop when the specified program address is reached for the N-th time,
where N is the number entered in the Passcount field. When some Advanced Breakpoint stops the program execution, passcount counters for all Advanced Breakpoints
will be cleared.
File Register Break
File Register Break can be used to stop the code execution when read/write access
to the specific data memory location occurs. If Read Access is selected, the File
Register Equal option can be used to set the matching value. The program execution will be stopped when the value read from the specified data memory location is
equal to the number written in the Value field. Values entered in the Address and
Value fields must be in hex format.
Note: File Register Break can also use the Passcount option in the same way as
Program Memory Break.
Emulator Features
Event Breakpoints
- Break on Stack Overflow/Underflow : not implemented.
- Break on Watchdog Timer : not implemented.
- Break on SLEEP : break on SLEEP instruction. SLEEP instruction will not be
executed. If you choose to continue the mikroICD debugging [F6] then the program
execution will start from the first instruction following the SLEEP instruction.
Stopwatch
Stopwatch uses Breakpoint#2 and Breakpoint#3 as a Start and Stop conditions.
To use the Stopwatch define these two Breakpoints and check the Enable
Stopwatch checkbox.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
111
CHAPTER 3
mikroPASCAL PRO for PIC
mikroICD
Stopwatch options:
- Halt on Start Condition (Breakpoint#2) : when checked, the program execution
will stop on Breakpoint#2. Otherwise, Breakpoint#2 will be used only to start the
Stopwatch.
- Halt on Stop Condition (Breakpoint#3) : when checked, the program execution
will stop on Breakpoint#3. Otherwise, Breakpoint#3 will be used only to stop the
Stopwatch.
- Reset Stopwatch on Run : when checked, the Stopwatch will be cleared before
continuing program execution and the next counting will start from zero. Otherwise,
the next counting will start from the previous Stopwatch value.
112
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER
4
mikroPascal PRO for PIC
Specifics
The following topics cover the specifics of mikroPascal PRO for PIC compiler:
- Pascal Standard Issues
- Predefined Globals and Constants
- Accessing Individual Bits
- Interrupts
- PIC Pointers
- Linker Directives
- Built-in Routines
- Code Optimization
113
CHAPTER 4
mikroPASCAL PRO for PIC
Specifics
PASCAL STANDARD ISSUES
Divergence from the Pascal Standard
- Function recursion is not supported because of no easily-usable stack and limited
memory PIC Specific
Pascal Language Extensions
mikroPascal PRO for PIC has additional set of keywords that do not belong to the
standard Pascal language keywords:
-
code
data
rx
sfr
at
sbit
bit
Related topics: Keywords, PIC Specific
114
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 4
mikroPASCAL PRO for PIC
Specifics
PREDEFINED GLOBALS AND CONSTANTS
SFRs and related constants
All PIC SFRs are implicitly declared as global variables of volatile word type. These
identifiers have an external linkage, and are visible in the entire project. When creating a project, the mikroPascal PRO for PIC will include an appropriate (*.mpas) file
from defs folder, containing declarations of available SFRs and constants (such as
PORTB, ADPCFG, etc). All identifiers are in upper case, identical to nomenclature
in the Microchip datasheets.
For a complete set of predefined globals and constants, look for “Defs” in the
mikroPascal PRO for PIC installation folder, or probe the Code Assistant for specific letters (Ctrl+Space in the Code Editor).
Math constants
In addition, several commonly used math constants are predefined in mikroPascal
PRO for PIC:
PI
PI_HALF
TWO_PI
E
= 3.1415926
= 1.5707963
= 6.2831853
= 2.7182818
Predefined project level defines
These defines are based on a value that you have entered/edited in the current project, and it is equal to the name of selected device for the project.
If 16F887 is selected device, then 16F887 token will be defined as 1, so it can be
used for conditional compilation:
{$IFDEF P16F887}
...
{$ENDIF}
Related topics: Project level defines
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
115
CHAPTER 4
mikroPASCAL PRO for PIC
Specifics
ACCESSING INDIVIDUAL BITS
The mikroPascal PRO for PIC allows you to access individual bits of 8-bit variables.
It also supports sbit and bit data types
Accessing Individual Bits Of Variables
If you are familiar with a particular MCU, you can access bits by name:
// Clear Global Interrupt Bit (GIE)
GIE_bit := 0;
Also, you can simply use the direct member selector (.) with a variable, followed by
a primary exression. Primary expression can be variable, constant, function call or
an expression enclosed by parentheses. For individual bit access there are predefined global constants B0, B1, … , B7 with B7 being the most significant bit:
// predefined globals as bit designators
// Clear bit 0 in INTCON register
INTCON.B0 := 0;
// literal constant as bit designator
// Set bit 5 in ADCON0 register
ADCON0.5 := 1;
// expression as bit designator
// Set bit 6 in STATUS register
i := 5;
STATUS.(i+1) := 1;
When using literal constants as bit designators instead of predefined ones, make
sure not to exceed the appropriate type size.
There is no need of any special declarations. This kind of selective access is an
intrinsic feature of mikropascal PRO for PIC and can be used anywhere in the code.
Identifiers B0–B7 are not case sensitive and have a specific namespace. You may
override them with your own members B0–B7 within any given structure.
See Predefined Globals and Constants for more information on register/bit names.
116
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 4
mikroPASCAL PRO for PIC
Specifics
sbit type
The mikroPascal PRO for PIC compiler has sbit data type which provides access to
bit-addressable SFRs. You can access them in several ways:
var LEDA : sbit at PORTA.B0;
var bit_name : sbit at sfr-name.B<bit-position>;
var LEDB : sbit at PORTB.0;
var bit_name : sbit at sfr-name.<bit-position>;
// If you are familiar with a particular MCU and its ports and direction registers (TRIS), you can access bits by their names:
var LEDC : sbit at RC0_bit;
var bit_name : sbit at R<port-letter><bit-position>_bit;
var TRISC0 : sbit at TRISC0_bit;
var bit_name : sbit at TRIS<port-letter><bit-position>_bit;
bit type
The mikroPascal PRO for PIC compiler provides a bit data type that may be used
for variable declarations. It can not be used for argument lists, and function-return
values.
var bf : bit;
// bit variable
There are no pointers to bit variables:
var ptr : ^bit;
// invalid
An array of type bit is not valid:
var arr[5] : bit;
// invalid
Note :
- Bit variables can not be initialized.
- Bit variables can not be members of records.
- Bit variables do not have addresses, therefore unary operator @ (address of) is
not applicable to these variables.
Related topics: Predefined globals and constants
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
117
CHAPTER 4
mikroPASCAL PRO for PIC
Specifics
INTERRUPTS
Interrupts can be easily handled by means of reserved word interrupt. mikroPascal
PRO for PIC implictly declares procedure interrupt which cannot be redeclared.
Write your own procedure body to handle interrupts in your application. Note that
you cannot call routines from within interrupt due to stack limitations.
mikroPascal PRO for PIC saves the following SFR on stack when entering interrupt
and pops them back upon return:
- PIC12 family: W, STATUS, FSR, PCLATH
- PIC16 family: W, STATUS, FSR, PCLATH
- PIC18 family: FSR (fast context is used to save WREG, STATUS, BSR)
P18 priority interrupts
Note: For the P18 family both low and high interrupts are supported.
For P18 low priority interrupts reserved word is interrupt_low:
1. function with name interrupt will be linked as ISR (interrupt service routine) for
high level interrupt
2. function with name interrupt_low will be linked as ISR for low level
interrupt_low
If interrupt priority feature is to be used then the user should set the appropriate SFR
bits to enable it. For more information refer to datasheet for specific device.
Routine Calls from Interrupt
Calling functions and procedures from within the interrupt routine is now possible.
The compiler takes care about the registers being used, both in "interrupt" and in
"begin" thread, and performs "smart" context-switching between the two, saving
only the registers that have been used in both threads.
The functions and procedures that don't have their own frame (no arguments and
local variables) can be called both from the interrupt and the "begin" thread.
118
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 4
mikroPASCAL PRO for PIC
Specifics
Interrupt Examples
Here is a simple example of handling the interrupts from TMR0 (if no other interrupts
are allowed):
procedure interrupt;
begin
counter := counter + 1;
TMR0 := 96;
INTCON := $20;
end;
In case of multiple interrupts enabled, you need to test which of the interrupts
occurred and then proceed with the appropriate code (interrupt handling):
procedure interrupt;
begin
if TestBit(INTCON, TMR0IF) = 1 then
begin
counter := counter + 1;
TMR0 := 96;
ClearBit(INTCON, TMR0F);
// ClearBit is realised as an inline function,
// and may be called from within an interrupt
end
else
if TestBit(INTCON, RBIF) = 1 then
begin
counter := counter + 1;
TMR0 := 96;
ClearBit(INTCON, RBIF);
end;
end;
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
119
CHAPTER 4
mikroPASCAL PRO for PIC
Specifics
LINKER DIRECTIVES
mikroPascal PRO for PIC uses internal algorithm to distribute objects within memory. If you need to have a variable or a routine at the specific predefined address, use
the linker directives absolute and org.
Note: You must specify an even address when using the linker directives.
Directive absolute
Directive absolute specifies the starting address in RAM for a variable. If the variable spans more than 1 word (16-bit), the higher words will be stored at the consecutive locations.
Directive absolute is appended to the declaration of a variable:
var x : word; absolute $32;
// Variable x will occupy 1 word (16 bits) at address $32
y : longint; absolute $34;
// Variable y will occupy 2 words at addresses $34 and $36
Be careful when using the absolute directive because you may overlap two variables by accident. For example:
var i : word; absolute $42;
// Variable i will occupy 1 word at address $42;
jj : longint; absolute $40;
// Variable will occupy 2 words at $40 and $42; thus,
// changing i changes jj at the same time and vice versa
Note: You must specify an even address when using the absolute directive.
120
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 4
mikroPASCAL PRO for PIC
Specifics
Directive org
Directive org specifies the starting address of a routine in ROM. It is appended to
the declaration of a routine. For example:
procedure proc(par : byte); org $200;
begin
// Procedure will start at address $200;
...
end;
org directive can be used with main routine too. For example:
program Led_Blinking;
procedure some_proc();
begin
...
end;
org 0x800;
begin
TRISB := 0;
// main procedure starts at 0x800
while TRUE do
begin
PORTB := 0x00;
Delay_ms(500);
PORTB := 0xFF;
Delay_ms(500);
end;
end.
Note: You must specify an even address when using the org directive.
Directive orgall
Use the orgall directive to specify the address above which all routines, constants
will be placed. Example:
begin
orgall(0x200) // All the routines, constants in main program will
be above the address 0x200
...
end.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
121
CHAPTER 4
mikroPASCAL PRO for PIC
Specifics
BUILT-IN ROUTINES
The mikroPascal PRO for PIC compiler provides a set of useful built-in utility functions.
The Lo, Hi, Higher, Highest routines are implemented as macros. If you want to
use these functions you must include built_in.h header file (located in the inlclude
folder of the compiler) into your project.
The Delay_us and Delay_ms routines are implemented as “inline”; i.e. code is generated in the place of a call, so the call doesn’t count against the nested call limit.
The Vdelay_ms, Delay_Cyc and Get_Fosc_kHz are actual Pascal routines. Their
sources can be found in Delays.mpas file located in the uses folder of the compiler.
-
Lo
Hi
Higher
Highest
- Inc
- Dec
- SetBit
- ClearBit
- TestBit
- Delay_us
- Delay_ms
- Clock_KHz
- Clock_MHz
- Reset
- ClrWdt
- DisableContextSaving
- SetFuncCall
- GetDateTime
- GetVersion
122
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 4
mikroPASCAL PRO for PIC
Specifics
Lo
Prototype
function Lo(number: longint): byte;
Returns
Lowest 8 bits (byte)of number, bits 7..0.
Function returns the lowest byte of number. Function does not interpret bit patterns of number – it merely returns 8 bits as found in register.
Description
This is an “inline” routine; code is generated in the place of the call, so the call
doesn’t count against the nested call limit.
Requires
Arguments must be variable of scalar type (i.e. Arithmetic Types and Pointers).
Example
d := 0x1AC30F4;
tmp := Lo(d); // Equals 0xF4
Hi
Prototype
function Hi(number: longint): byte;
Returns
Returns next to the lowest byte of number, bits 8..15.
Function returns next to the lowest byte of number. Function does not interpret
bit patterns of number – it merely returns 8 bits as found in register.
Description
This is an “inline” routine; code is generated in the place of the call, so the call
doesn’t count against the nested call limit.
Requires
Arguments must be variable of scalar type (i.e. Arithmetic Types and Pointers).
Example
d := 0x1AC30F4;
tmp := Hi(d); // Equals 0x30
Higher
Prototype
function Higher(number: longint): byte;
Returns
Returns next to the highest byte of number, bits 16..23.
Function returns next to the highest byte of number. Function does not interpret
bit patterns of number – it merely returns 8 bits as found in register.
Description
This is an “inline” routine; code is generated in the place of the call, so the call
doesn’t count against the nested call limit.
Requires
Arguments must be variable of scalar type (i.e. Arithmetic Types and Pointers).
Example
d := 0x1AC30F4;
tmp := Higher(d);
// Equals 0xAC
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
123
CHAPTER 4
mikroPASCAL PRO for PIC
Specifics
Highest
Prototype
function Highest(number: longint): byte;
Returns
Returns the highest byte of number, bits 24..31.
Function returns the highest byte of number. Function does not interpret bit patterns of number – it merely returns 8 bits as found in register.
Description
This is an “inline” routine; code is generated in the place of the call, so the call
doesn’t count against the nested call limit.
Requires
Arguments must be variable of scalar type (i.e. Arithmetic Types and Pointers).
Example
d := 0x1AC30F4;
tmp := Highest(d);
// Equals 0x01
Inc
Prototype
procedure Inc(var par : longint);
Returns
Nothing.
Description Increases parameter par by 1.
Requires
Nothing.
Example
p := 4;
Inc(p);
// p is now 5
Dec
Prototype
procedure Dec(var par : longint);
Returns
Nothing.
Description Decreases parameter par by 1.
124
Requires
Nothing.
Example
p := 4;
Dec(p);
// p is now 3
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 4
mikroPASCAL PRO for PIC
Specifics
SetBit
Prototype
procedure SetBit(var register : byte; rbit : byte);
Returns
Nothing.
Description
Function sets the bit rbit of register. Parameter rbit needs to be a variable or
literal with value 0..7. See Predefined globals and constants for more information on register identifiers.
This is an “inline” routine; code is generated in the place of the call, so the call
doesn’t count against the nested call limit.
Requires
Nothing.
Example
SetBit(PORTB, 2);
// Set RB2
ClearBit
Prototype
procedure ClearBit(var register : byte; rbit : byte);
Returns
Nothing.
Description
Function clears the bit rbit of register. Parameter rbit needs to be a variable or literal with value 0..7. See Predefined globals and constants for more
information on register identifiers.
This is an “inline” routine; code is generated in the place of the call, so the call
doesn’t count against the nested call limit.
Requires
Nothing.
Example
ClearBit(PORTC, 7);
// Clear RC7
TestBit
Prototype
function TestBit(register, rbit : byte) : byte;
Returns
If the bit is set, returns 1, otherwise returns 0.
Description
Function tests if the bit rbit of register is set. If set, function returns 1, otherwise
returns 0. Parameter rbit needs to be a variable or literal with value 0..7. See Predefined globals and constants for more information on register identifiers.
This is an “inline” routine; code is generated in the place of the call, so the call
doesn’t count against the nested call limit.
Requires
Nothing.
Example
flag := TestBit(PORTE, 2);
// 1 if RE2 is set, otherwise 0
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
125
CHAPTER 4
mikroPASCAL PRO for PIC
Specifics
Delay_us
Prototype
procedure Delay_us(time_in_us: const longword);
Returns
Nothing.
Creates a software delay in duration of time_in_us microseconds (a constant).
Range of applicable constants depends on the oscillator frequency.
Description
This is an “inline” routine; code is generated in the place of the call, so the call
doesn’t count against the nested call limit.
Requires
Nothing.
Example
Delay_us(1000);
// One millisecond pause
Delay_ms
Prototype
procedure Delay_ms(time_in_ms: const longword);
Returns
Nothing.
Creates a software delay in duration of time_in_ms milliseconds (a constant).
Range of applicable constants depends on the oscillator frequency.
Description
This is an “inline” routine; code is generated in the place of the call, so the call
doesn’t count against the nested call limit.
Requires
Nothing.
Example
Delay_ms(1000);
// One second pause
Clock_KHz
Prototype
function Clock_KHz(): word;
Returns
Device clock in KHz, rounded to the nearest integer.
Function returns device clock in KHz, rounded to the nearest integer.
Description
126
This is an “inline” routine; code is generated in the place of the call, so the call
doesn’t count against the nested call limit.
Requires
Nothing.
Example
clk := Clock_kHz();
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 4
mikroPASCAL PRO for PIC
Specifics
Clock_MHz
Prototype
function Clock_MHz(): byte;
Returns
Device clock in MHz, rounded to the nearest integer.
Function returns device clock in MHz, rounded to the nearest integer.
Description
This is an “inline” routine; code is generated in the place of the call, so the call
doesn’t count against the nested call limit.
Requires
Nothing.
Example
clk := Clock_MHz();
Reset
Prototype
procedure Reset;
Returns
Nothing.
Description
This procedure is equal to assembler instruction reset. This procedure works
only for P18.
Requires
Nothing.
Example
Reset; //Resets the PIC MCU
ClrWdt
Prototype
procedure ClrWdt();
Returns
Nothing.
Description This procedure is equal to assembler instruction clrwdt.
Requires
Nothing.
Example
ClrWdt; //Clears PIC's WDT
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
127
CHAPTER 4
mikroPASCAL PRO for PIC
Specifics
DisableContextSaving
Prototype
procedure DisableContextSaving();
Returns
Nothing.
Use the DisableContextSaving() to instruct the compiler not to automatically
perform context-switching. This means that no regiser will be saved/restored by
Description the compiler on entrance/exit from interrupt service routine. This enables the
user to manually write code for saving registers upon entrance and to restore
them before exit from interrupt.
Requires
This routine must be called from main.
Example
DisableContextSaving(); //instruct the compiler not to automatically perform context-switching
SetFuncCall
Prototype
procedure SetFuncCall(FuncName: string);
Returns
Nothing.
Function informs the linker about a specific routine being called. SetFuncCall
has to be called in a routine which accesses another routine via a pointer.
Description
Function prepares the caller tree, and informs linker about the procedure usage,
making it possible to link the called routine.
128
Requires
Nothing.
Example
procedure first(p, q: byte);
begin
...
SetFuncCall(second); // let linker know that we will call the
routine 'second'
...
end
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 4
mikroPASCAL PRO for PIC
Specifics
GetDateTime
Prototype
function GetDateTime() : string;
Returns
String with date and time when this routine is compiled.
Description Use the GetDateTime() to get date and time of compilation as string in your code.
Requires
Nothing.
Example
str := GetDateTime();
GetVersion
Prototype
function GetVersion() : string;
Returns
String with current compiler version.
Description Use the GetVersion() to get the current version of compiler.
Requires
Nothing.
Example
str := GetVersion(); // for example, str will take the value of
'8.2.1.6'
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
129
CHAPTER 4
mikroPASCAL PRO for PIC
Specifics
CODE OPTIMIZATION
Optimizer has been added to extend the compiler usability, cut down the amount of
code generated and speed-up its execution. The main features are:
Constant folding
All expressions that can be evaluated in the compile time (i.e. are constant) are
being replaced by their results. (3 + 5 -> 8);
Constant propagation
When a constant value is being assigned to a certain variable, the compiler recognizes this and replaces the use of the variable by constant in the code that follows,
as long as the value of a variable remains unchanged.
Copy propagation
The compiler recognizes that two variables have the same value and eliminates one
of them further in the code.
Value numbering
The compiler "recognizes" if two expressions yield the same result and can therefore eliminate the entire computation for one of them.
"Dead code" ellimination
The code snippets that are not being used elsewhere in the programme do not affect
the final result of the application. They are automatically removed.
Stack allocation
Temporary registers ("Stacks") are being used more rationally, allowing VERY complex expressions to be evaluated with a minimum stack consumption.
Local vars optimization
No local variables are being used if their result does not affect some of the global or
volatile variables.
Better code generation and local optimization
Code generation is more consistent and more attention is payed to implement specific solutions for the code "building bricks" that further reduce output code size.
130
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER
5
PIC Specifics
In order to get the most from your mikroPascal PRO for PIC compiler, you should
be familiar with certain aspects of PIC MCU. This knowledge is not essential, but it
can provide you a better understanding of PICs’ capabilities and limitations, and
their impact on the code writing.
131
CHAPTER 5
mikroPASCAL PRO for PIC
PIC Specifics
Types Efficiency
First of all, you should know that PIC’s ALU, which performs arithmetic operations,
is optimized for working with bytes. Although mikroPascal PRO for PIC is capable of
handling very complex data types, PIC may choke on them, especially if you are
working on some of the older models. This can dramatically increase the time needed for performing even simple operations. Universal advice is to use the smallest
possible type in every situation. It applies to all programming in general, and doubly
so with microcontrollers.
Get to know your tool. When it comes down to calculus, not all PIC MCUs are of
equal performance. For example, PIC16 family lacks hardware resources to multiply two bytes, so it is compensated by a software algorithm. On the other hand,
PIC18 family has HW multiplier, and as a result, multiplication works considerably
faster.
Nested Calls Limitations
Nested call represents a function call within function body, either to itself (recursive
calls) or to another function. Recursive function calls are supported by mikroPascal
PRO for PIC but with limitations. Recursive function calls can't contain any function
parameters and local variables due to the PIC’s stack and memory limitations.
mikroPascal PRO for PIC limits the number of non-recursive nested calls to:
- 8 calls for PIC12 family,
- 8 calls for PIC16 family,
- 31 calls for PIC18 family.
Note that some of the built-in routines do not count against this limit, due to their
“inline” implementation.
Number of the allowed nested calls decreases by one if you use any of the following operators in the code: * / %. It further decreases if you use interrupts in the program. Number of decreases is specified by number of functions called from interrupt. Check functions reentrancy.
If the allowed number of nested calls is exceeded, the compiler will report a stack
overflow error.
132
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 5
mikroPASCAL PRO for PIC
PIC Specifics
PIC18FxxJxx Specifics
Shared Address SFRs
mikroPascal PRO for PIC does not provide auto setting of bit for acessing alternate
register. This is new feature added to pic18fxxjxx family and will be supported in
future. In several locations in the SFR bank, a single address is used to access two
different hardware registers. In these cases, a “legacy” register of the standard
PIC18 SFR set (such as OSCCON, T1CON, etc.) shares its address with an alternate register. These alternate registers are associated with enhanced configuration
options for peripherals, or with new device features not included in the standard
PIC18 SFR map. A complete list of shared register addresses and the registers
associated with them is provided in datasheet.
PIC16 Specifics
Breaking Through Pages
In applications targeted at PIC16, no single routine should exceed one page (2,000
instructions). If routine does not fit within one page, linker will report an error. When
confront with this problem, maybe you should rethink the design of your application
– try breaking the particular routine into several chunks, etc.
Limits of Indirect Approach Through FSR
Pointers with PIC16 are “near”: they carry only the lower 8 bits of the address. Compiler will automatically clear the 9th bit upon startup, so that pointers will refer to
banks 0 and 1. To access the objects in banks 2 or 3 via pointer, user should manually set the IRP, and restore it to zero after the operation. The stated rules apply to
any indirect approach: arrays, structures and unions assignments, etc.
Note: It is very important to take care of the IRP properly, if you plan to follow this
approach. If you find this method to be inappropriate with too many variables, you
might consider upgrading to PIC18.
Note: If you have many variables in the code, try rearranging them with the linker
directive absolute. Variables that are approached only directly should be moved to
banks 3 and 4 for increased efficiency.
Related topics: mikroPascal PRO for PIC specifics
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
133
CHAPTER 5
mikroPASCAL PRO for PIC
PIC Specifics
MEMORY TYPE SPECIFIERS
The mikroPascal PRO for PIC supports usage of all memory areas. Each variable may be explicitly assigned to a specific memory space by including a memory type specifier in the declaration,
or implicitly assigned.
The following memory type specifiers can be used:
-
code
data
rx
sfr
Memory type specifiers can be included in variable declaration.
For example:
var data_buffer : char; data;
// puts data_buffer in data ram
const txt = 'Enter parameter'; code; // puts text in program memory
code
Description The code memory type may be used for allocating constants in program memory.
Example
// puts txt in program memory
const txt = 'Enter parameter'; code;
data
Description This memory specifier is used when storing variable to the internal data SRAM.
Example
// puts data_buffer in data ram
var data_buffer : char; data;
rx
This memory specifier allows variable to be stored in the Rx space (Register file).
Description
Example
134
Note: In most of the cases, there will be enough space left for the user variables
in the Rx space. However, since compiler uses Rx space for storing temporary
variables, it might happen that user variables will be stored in the internal data
SRAM, when writing complex programs.
// puts y in Rx space
var y : char; rx;
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 5
mikroPASCAL PRO for PIC
PIC Specifics
sfr
This memory specifier in combination with (rx, io, data) allows user to access
Description special function registers. It also instructs compiler to maintain same identifier in
Pascal and assembly.
Example
var y : char; rx; sfr;
// puts y in Rx space
Note: If none of the memory specifiers are used when declaring a variable, data specifier will be
set as default by the compiler.
Related topics: Accessing individual bits, SFRs, Constants, Functions
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
135
CHAPTER 5
PIC Specifics
136
mikroPASCAL PRO for PIC
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER
6
mikroPascal PRO for PIC
Language Reference
The mikroPascal PRO for AVR Language Reference describes the syntax, semantics and implementation of the mikroPascal PRO for AVR language.
The aim of this reference guide is to provide a more understandable description of
the mikroPascal PRO for AVR language to the user.
137
CHAPTER 6
Language Reference
mikroPASCAL PRO for PIC
Lexical Elements
Whitespace
Comments
Tokens
Literals
Keywords
Identifiers
Punctuators
Program Organization
Program Organization
Scope and Visibility
Units
Variables
Constants
Labels
Functions and Procedures
Functions
Procedures
Types
Simple Types
Arrays
Strings
Pointers
Records
Types Conversions
Implicit Conversion
Explicit Conversion
Operators
Introduction to Operators
Operators Precedence and Associativity
Arithmetic Operators
Relational Operators
Bitwise Operators
Boolean Operators
Expressions
Expressions
Statements
Introduction to Statements
Assignment Statements
Compound Statements (Blocks)
Conditional Statements
138
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
If Statement
Case Statement
Iteration Statements (Loops)
For Statement
While Statement
Repeat Statement
Jump Statements
Break and Continue Statements
Exit Statement
Goto Statement
asm Statement
Directives
Compiler Directives
Linker Directives
LEXICAL ELEMENTS OVERVIEW
The following topics provide a formal definition of the mikroPascal PRO for PIC lexical elements. They describe different categories of word-like units (tokens) recognized by mikroPascal PRO for PIC.
In the tokenizing phase of compilation, the source code file is parsed (i.e. broken
down) into tokens and whitespace. The tokens in mikroPascal PRO for PIC are
derived from a series of operations performed on your programs by the compiler.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
139
CHAPTER 6
Language Reference
mikroPASCAL PRO for PIC
WHITESPACE
Whitespace is a collective name given to spaces (blanks), horizontal and vertical
tabs, newline characters and comments. Whitespace can serve to indicate where
tokens start and end, but beyond this function, any surplus whitespace is discarded.
For example, two sequences
var i : char;
j : word;and
var
i : char;
j : word;
are lexically equivalent and parse identically to give nine tokens:
var
i
:
char
;
j
:
word
;
Whitespace in Strings
The ASCII characters representing whitespace can occur within string literals, in
which case they are protected from the normal parsing process (they remain a part
of the string). For example,
some_string := 'mikro foo';
parses into four tokens, including a single string literal token:
some_string
:=
'mikro foo'
;
140
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
COMMENTS
Comments are pieces of a text used to annotate a program, and are technically
another form of whitespace. Comments are for the programmer’s use only. They are
stripped from the source text before parsing.
There are two ways to create comments in mikroPascal. You can use multi-line comments which are enclosed with braces or (* and *):
{ All text between left and right brace
constitutes a comment. May span multiple lines. }
(* Comment can be
written in this way too. *)
or single-line comments:
// Any text between a double-slash and the end of the
// line constitutes a comment spanning one line only.
Nested comments
mikroPascal PRO for PIC doesn’t allow nested comments. The attempt to nest a
comment like this
{ i { identifier } : word; }
fails, because the scope of the first open brace “{” ends at the first closed brace “}”.
This gives us
: word; }
which would generate a syntax error.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
141
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
TOKENS
Token is the smallest element of the Pascal program that compiler can recognize.
The parser separates tokens from the input stream by creating the longest token
possible using the input characters in a left–to–right scan.
mikroPascal PRO for PIC recognizes the following kinds of tokens:
-
keywords
identifiers
constants
operators
punctuators (also known as separators)
Token Extraction Example
Here is an example of token extraction. Take a look at the following example code
sequence:
end_flag := 0;
First, note that end_flag would be parsed as a single identifier, rather than as the
keyword end followed by the identifier _flag.
The compiler would parse it as the following four tokens:
end_flag
:=
0
;
// variable identifier
// assignment operator
// literal
// statement terminator
Note that := parses as one token (the longest token possible), not as token : followed by token =.
142
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
LITERALS
Literals are tokens representing fixed numeric or character values.
The data type of a constant is deduced by the compiler using such clues as numeric value and format used in the source code.
Integer Literals
Integral values can be represented in decimal, hexadecimal, or binary notation.
In decimal notation, numerals are represented as a sequence of digits (without commas, spaces, or dots), with optional prefix + or - operator to indicate the sign. Values
default to positive (6258 is equivalent to +6258).
The dollar-sign prefix ($) or the prefix 0x indicates a hexadecimal numeral (for
example, $8F or 0x8F).
The percent-sign prefix (%) indicates a binary numeral (for example, %01010000).
Here are some examples:
11
$11
0x11
%11
//
//
//
//
decimal literal
hex literal, equals decimal 17
hex literal, equals decimal 17
binary literal, equals decimal 3
The allowed range of values is imposed by the largest data type in mikroPascal
PRO for PIC – longint. Compiler will report an error if the literal exceeds 2147483647
($7FFFFFFF).
Floating Point Literals
A floating-point value consists of:
-
Decimal integer
Decimal point
Decimal fraction
e or E and a signed integer exponent (optional)
You can omit either the decimal integer or decimal fraction (but not both).
Negative floating constants are taken as positive constants with the unary operator
minus (-) prefixed.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
143
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
mikroPascal PRO for PIC limits floating-point constants to range ±1.17549435082 *
10-38 .. ±6.80564774407 * 1038.
Here are some examples:
0.
-1.23
23.45e6
2e-5
3E+10
.09E34
//
//
//
//
//
//
=
=
=
=
=
=
0.0
-1.23
23.45 * 10^6
2.0 * 10^-5
3.0 * 10^10
0.09 * 10^34
Character Literals
Character literal is one character from the extended ASCII character set, enclosed
with apostrophes.
Character literal can be assigned to variables of the byte and char type (variable of
byte will be assigned the ASCII value of the character). Also, you can assign character literal to a string variable.
Note: Quotes ("") have no special meaning in mikroPascal PRO for PIC.
String Literals
String literal is a sequence of characters from the extended ASCII character set,
written in one line and enclosed with apostrophes. Whitespace is preserved in string
literals, i.e. parser does not “go into” strings but treats them as single tokens.
Length of string literal is a number of characters it consists of. String is stored internally as the given sequence of characters plus a final null character. This null character is introduced to terminate the string, it does not count against the string’s total
length.
String literal with nothing in between the apostrophes (null string) is stored as a single null character.
You can assign string literal to a string variable or to an array of char.
Here are several string literals:
'Hello world!'
// message, 12 chars long
'Temperature is stable' // message, 21 chars long
' '
// two spaces, 2 chars long
'C'
// letter, 1 char long
''
// null string, 0 chars long
The apostrophe itself cannot be a part of the string literal, i.e. there is no escape
sequence. You can use the built-in function Chr to print an apostrophe: Chr(39).
Also, see String Splicing.
144
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
KEYWORDS
Keywords are the words reserved for special purposes and must not be used as normal identifier names.
Beside standard Pascal keywords, all relevant SFRs are defined as global variables
and represent reserved words that cannot be redefined (for example: W0, TMR1,
T1CON, etc). Probe the Code Assistant for specific letters (Ctrl+Space in Editor) or
refer to Predefined Globals and Constants.
Here is the alphabetical listing of keywords in Pascal:
-
absolute
abstract
and
array
as
asm
assembler
at
automated
bdata
begin
bit
case
cdecl
class
code
compact
const
constructor
contains
data
default
deprecated
destructor
dispid
dispinterface
div
do
downto
dynamic
end
except
export
exports
external
far
file
final
finalization
finally
-
for
forward
goto
helper
idata
if
ilevel
implementation
implements
in
index
inherited
initialization
inline
interface
is
label
library
message
mod
name
near
nil
nodefault
not
object
of
on
operator
or
org
out
overload
override
package
packed
pascal
pdata
platform
private
-
procedure
program
property
protected
public
published
raise
read
readonly
record
register
reintroduce
repeat
requires
safecall
sbit
sealed
set
shl
shr
small
stdcall
stored
string
threadvar
to
try
type
unit
until
uses
var
virtual
volatile
while
with
write
writeonly
xdata
xor
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
145
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
Also, mikroPascal PRO for PIC includes a number of predefined identifiers used in
libraries. You can replace them by your own definitions, if you plan to develop your
own libraries. For more information, see mikroPascal for PIC Libraries.
IDENTIFIERS
Identifiers are arbitrary names of any length given to functions, variables, symbolic
constants, user-defined data types and labels. All these program elements will be
referred to as objects throughout the help (don't get confused about the meaning of
object in object-oriented programming).
Identifiers can contain the letters a to z and A to Z, underscore character “_”, and
digits from 0 to 9. The only restriction is that the first character must be a letter or an
underscore.
Case Sensitivity
Pascal is not case sensitive, so Sum, sum, and suM are an equivalent identifier.
Uniqueness and Scope
Although identifier names are arbitrary (according to the stated rules), if the same
name is used for more than one identifier within the same scope then error arises.
Duplicated names are illegal within same scope. For more information, refer to
Scope and Visibility.
Identifier Examples
Here are some valid identifiers:
temperature_V1
Pressure
no_hit
dat2string
SUM3
_vtext
… and here are some invalid identifiers:
7temp
%higher
xor
j23.07.04
146
//
//
//
//
NO
NO
NO
NO
-----
cannot
cannot
cannot
cannot
begin with a numeral
contain special characters
match reserved word
contain special characters (dot)
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
PUNCTUATORS
The mikroPascal punctuators (also known as separators) are:
-
[ ] – Brackets
( ) – Parentheses
, – Comma
; – Semicolon
: – Colon
. – Dot
Brackets
Brackets [ ] indicate single and multidimensional array subscripts:
var alphabet : array[1..30] of byte;
// ...
alphabet[3] := 'c';
For more information, refer to Arrays.
Parentheses
Parentheses ( ) are used to group expressions, isolate conditional expressions and
indicate function calls and function declarations:
d := c * (a + b);
if (d = z) then ...
func();
function func2(n : word);
// Override normal precedence
// Useful with conditional statements
// Function call, no arguments
// Function declaration with parameters
For more information, refer to Operators Precedence and Associativity, Expressions
and Functions and Procedures.
Comma
Comma (,) separates the arguments in function calls:
LCD_Out(1, 1, txt);
Further, the comma separates identifiers in declarations:
var i, j, k : byte;
The comma also separates elements of array in initialization lists:
const
MONTHS
:
array[1..12]
(31,28,31,30,31,30,31,31,30,31,30,31);
of
byte
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
=
147
CHAPTER 6
Language Reference
mikroPASCAL PRO for PIC
Semicolon
Semicolon (;) is a statement terminator. Every statement in Pascal must be terminated with a semicolon. The exceptions are: the last (outer most) end statement in
the program which is terminated with a dot and the last statement before end which
doesn't need to be terminated with a semicolon.
For more information, see Statements.
Colon
Colon (:) is used in declarations to separate identifier list from type identifier. For
example:
var
i, j : byte;
k
: word;
In the program, use the colon to indicate a labeled statement:
start: nop;
...
goto start;
For more information, refer to Labels.
Dot
Dot (.) indicates an access to a field of a record. For example:
person.surname := 'Smith';
For more information, refer to Records.
Dot is a necessary part of floating point literals. Also, dot can be used for accessing
individual bits of registers in mikroPascal.
148
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
PROGRAM ORGANIZATION
Pascal imposes quite strict program organization. Below you can find models for
writing legible and organized source files. For more information on file inclusion and
scope, refer to Units and Scope and Visibility.
Organization of Main Unit
Basically, the main source file has two sections: declaration and program body. Declarations should be in their proper place in the code, organized in an orderly manner. Otherwise, the compiler may not be able to comprehend the program correctly.
When writing code, follow the model presented below. The main unit should look like
this:
program { program name }
uses { include other units }
//********************************************************
//* Declarations (globals):
//********************************************************
{ constants declarations }
const ...
{ types declarations }
type ...
{ variables declarations }
var Name[, Name2...] : [^]type;
[volatile;] [register;] [sfr;]
[absolute
0x123;]
[external;]
{ labels declarations }
label ...
{ procedures declarations }
procedure procedure_name(parameter_list);
{ local declarations }
begin
...
end;
{ functions declarations }
function function_name(parameter_list) : return_type;
{ local declarations }
begin
...
end;
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
149
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
//********************************************************
//* Program body:
//********************************************************
begin
{ write your code here }
end.
Organization of Other Units
Units other than main start with the keyword unit. Implementation section starts with
the keyword implementation. Follow the model presented below:
unit { unit name }
uses { include other units }
//********************************************************
//* Interface (globals):
//********************************************************
{ constants declarations }
const ...
{ types declarations }
type ...
{ variables declarations }
var Name[, Name2...] : [^]type;
[volatile;] [register;] [sfr;]
[absolute
0x123;]
[external;]
{ procedures prototypes }
procedure procedure_name([var] [const] ParamName : [^]type; [var]
[const] ParamName2, ParamName3 : [^]type);
{ functions prototypes }
function function_name([var] [const] ParamName : [^]type;
[const] ParamName2, ParamName3 : [^]type) : [^]type;
[var]
//********************************************************
//* Implementation:
//********************************************************
implementation
{ constants declarations }
const ...
{ types declarations }
type ...
150
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
{ variables declarations }
var Name[, Name2...] : [^]type;
[volatile;] [register;] [sfr;]
Language Reference
[absolute
0x123;]
[external;]
{ labels declarations }
label ...
{ procedures declarations }
procedure procedure_name([var] [const] ParamName : [^]type; [var]
[const] ParamName2, ParamName3 : [^]type); [ilevel 0x123;] [overload;] [forward;]
{ local declarations }
begin
...
end;
{ functions declarations }
function function_name([var] [const] ParamName : [^]type; [var]
[const] ParamName2, ParamName3 : [^]type) : [^]type; [ilevel 0x123;]
[overload;] [forward;]
{ local declarations }
begin
...
end;
end.
Note: constants, types and variables used in the implementation section are inaccessible to other units. This feature is not applied to the procedures and functions in
the current version, but it will be added to the future ones.
Note: Functions and procedures must have the same declarations in the interface
and implementation section. Otherwise, compiler will report an error.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
151
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
SCOPE AND VISIBILITY
Scope
The scope of an identifier is a part of the program in which the identifier can be used
to access its object. There are different categories of scope, which depends on how
and where identifiers are declared:
Place of declaration
Scope
Scope extends from the point where it is declared
to the end of the current block, including all
Identifier is declared in the
blocks enclosed within that scope. Identifiers in
declaration of a program, functhe outermost scope (file scope) of the main unit
tion, or procedure
are referred to as globals, while other identifiers
are locals.
Identifier is declared in the
interface section of a unit
Scope extends the interface section of a unit from
the point where it is declared to the end of the
unit, and to any other unit or program that uses
that unit.
Identifier is declared in the
Scope extends from the point where it is declared
implementation section of a
to the end of the unit. The identifier is available to
unit, but not within the block of
any function or procedure in the unit.
any function or procedure
Visibility
The visibility of an identifier is that region of the program source code from which
legal access to the identifier’s associated object can be made.
Scope and visibility usually coincide, though there are circumstances under which
an object becomes temporarily hidden by the appearance of a duplicate identifier,
i.e. the object still exists but the original identifier cannot be used to access it until
the scope of the duplicate identifier is ended.
Technically, visibility cannot exceed scope, but scope can exceed visibility.
152
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
UNITS
In mikroPascal PRO for PIC, each project consists of a single project file and one or
more unit files. Project file, with extension .mpppi contains information about the
project, while unit files, with extension .mpas, contain the actual source code.
Units allow you to:
- break large programs into encapsulated parts that can be edited separately,
- create libraries that can be used in different projects,
- distribute libraries to other developers without disclosing the source code.
Each unit is stored in its own file and compiled separately. Compiled units are linked
to create an application. In order to build a project, the compiler needs either a
source file or a compiled unit file (.mcl file) for each unit.
Uses Clause
mikroPascal PRO for PIC includes units by means of the uses clause. It consists of
the reserved word uses, followed by one or more comma-delimited unit names, followed by a semicolon. Extension of the file should not be included. There can be at
most one uses clause in each source file, and it must appear immediately after the
program (or unit) name.
Here’s an example:
uses utils, strings, Unit2, MyUnit;
For the given unit name, the compiler will check for the presence of .mcl and .mpas
files, in order specified by the search paths.
- If both .mpas and .mcl files are found, the compiler will check their dates and
include the newer one in the project. If the .mpas file is newer than .mcl, a new
library will be written over the old one;
- If only .mpas file is found, the compiler will create the .mcl file and include it in the
project;
- If only .mcl file is present, i.e. no source code is available, the compiler will include
it as it is found;
- If none found, the compiler will issue a “File not found” warning.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
153
CHAPTER 6
Language Reference
mikroPASCAL PRO for PIC
Main Unit
Every project in mikroPascal PRO for PIC requires a single main unit file. The main
unit file is identified by the keyword program at the beginning; it instructs the compiler where to “start”.
After you have successfully created an empty project with the Project Wizard, the
Code Editor will display a new main unit. It contains the bare-bones of the Pascal
program:
program MyProject;
{ main procedure }
begin
{ Place program code here }
end.
Nothing should precede the keyword program except comments. After the program
name, you can optionally place the uses clause.
Place all global declarations (constants, variables, types, labels, routines) before the
keyword begin.
Other Units
Units other than main start with the keyword unit. Newly created blank unit contains
the bare-bones:
unit MyUnit;
implementation
end.
Other than comments, nothing should precede the keyword unit. After the unit
name, you can optionally place the uses clause.
Interface Section
Part of the unit above the keyword implementation is referred to as interface section. Here, you can place global declarations (constants, variables, labels and types)
for the project.
You do not define routines in the interface section. Instead, state the prototypes of
routines (from implementation section) that you want to be visible outside the unit.
Prototypes must match the declarations exactly.
154
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
Implementation Section
Implementation section hides all irrelevant innards from other units, allowing encapsulation of code.
Everything declared below the keyword implementation is private, i.e. has its
scope limited to the file. When you declare an identifier in the implementation section of a unit, you cannot use it outside the unit, but you can use it in any block or
routine defined within the unit.
By placing the prototype in the interface section of the unit (above the implementation) you can make the routine public, i.e. visible outside of unit. Prototypes must
match the declarations exactly.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
155
CHAPTER 6
Language Reference
mikroPASCAL PRO for PIC
VARIABLES
Variable is object whose value can be changed during the runtime. Every variable is
declared under unique name which must be a valid identifier. This name is used for
accessing the memory location occupied by a variable.
Variables are declared in the declaration part of the file or routine — each variable needs
to be declared before being used. Global variables (those that do not belong to any
enclosing block) are declared below the uses statement, above the keyword begin.
Specifying a data type for each variable is mandatory. Syntax for variable declaration is:
var identifier_list : type;
identifier_list is a comma-delimited list of valid identifiers and type can be any
data type.
For more details refer to Types and Types Conversions. For more information on
variables’ scope refer to the chapter Scope and Visibility.
Pascal allows shortened syntax with only one keyword var followed by multiple variable declarations. For example:
var i, j, k : byte;
counter, temp : word;
samples : array[100] of word;
External Modifier
Use the external modifier to indicate that the actual place and initial value of the variable, or body of the function, is defined in a separate source code unit.
Variables and PIC
Every declared variable consumes part of RAM. Data type of variable determines
not only allowed range of values, but also the space variable occupies in RAM. Bear
in mind that operations using different types of variables take different time to be
completed. mikroPascal PRO for PIC recycles local variable memory space – local
variables declared in different functions and procedures share the same memory
space, if possible.
There is no need to declare SFRs explicitly, as mikroPascal PRO for PIC automatically
declares relevant registers as global variables of volatile word see SFR for details.
156
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
CONSTANTS
Constant is a data whose value cannot be changed during the runtime. Using a constant in a program consumes no RAM. Constants can be used in any expression,
but cannot be assigned a new value.
Constants are declared in the declaration part of a program or routine. You can
declare any number of constants after the keyword const:
const constant_name [: type] = value;
Every constant is declared under unique constant_name which must be a valid
identifier. It is a tradition to write constant names in uppercase. Constant requires
you to specify value, which is a literal appropriate for the given type. type is optional and in the absence of type, the compiler assumes the “smallest” of all types that
can accommodate value.
Note: You cannot omit type when declaring a constant array.
Pascal allows shorthand syntax with only one keyword const followed by multiple
constant declarations. Here’s an example:
const
MAX : longint = 10000;
MIN = 1000;
// compiler will assume word type
SWITCH = 'n';
// compiler will assume char type
MSG = 'Hello';
// compiler will assume string type
MONTHS
:
array[1..12]
of
(31,28,31,30,31,30,31,31,30,31,30,31);
byte
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
=
157
CHAPTER 6
Language Reference
mikroPASCAL PRO for PIC
LABELS
Labels serve as targets for goto statements. Mark the desired statement with a label
and colon like this:
label_identifier : statement
Before marking a statement, you must declare a label. Labels are declared in declaration part of unit or routine, similar to variables and constants. Declare labels
using the keyword label:
label label1, ..., labeln;
Name of the label needs to be a valid identifier. The label declaration, marked statement, and goto statement must belong to the same block. Hence it is not possible
to jump into or out of a procedure or function. Do not mark more than one statement
in a block with the same label.
Here is an example of an infinite loop that calls the Beep procedure repeatedly:
label loop;
...
loop:
Beep;
goto loop;
Note: label should be followed by end of line (CR) otherwise compiler will report an
error:
label loop;
...
loop: Beep; // compiler will report an error
loop: // compiler will report an error
158
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
FUNCTIONS AND PROCEDURES
Functions and procedures, collectively referred to as routines, are subprograms
(self-contained statement blocks) which perform a certain task based on a number
of input parameters. When executed, a function returns a value while procedure
does not.
mikroPascal PRO for PIC does not support inline routines.
Functions
A function is declared like this:
function function_name(parameter_list) : return_type;
{ local declarations }
begin
{ function body }
end;
function_name represents a function’s name and can be any valid identifier.
return_type is a type of return value and can be any simple type. Within parentheses, parameter_list is a formal parameter list very similar to variable declaration.
In Pascal, parameters are always passed to a function by the value — to pass an
argument by address, add the keyword var ahead of identifier.
Local declarations are optional declarations of variables and/or constants, local
for the given function. Function body is a sequence of statements to be executed
upon calling the function.
Calling a function
A function is called by its name, with actual arguments placed in the same sequence
as their matching formal parameters. The compiler is able to coerce mismatching
arguments to the proper type according to implicit conversion rules. Upon a function
call, all formal parameters are created as local objects initialized by values of actual arguments. Upon return from a function, a temporary object is created in the place
of the call and it is initialized by the value of the function result. This means that function call as an operand in complex expression is treated as the function result.
In standard Pascal, a function_name is automatically created local variable that can
be used for returning a value of a function. mikroPascal PRO for PIC also allows you
to use the automatically created local variable result to assign the return value of a
function if you find function name to be too ponderous. If the return value of a function is not defined the compiler will report an error.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
159
CHAPTER 6
Language Reference
mikroPASCAL PRO for PIC
Function calls are considered to be primary expressions and can be used in situations where expression is expected. A function call can also be a self-contained
statement and in that case the return value is discarded.
Example
Here’s a simple function which calculates xn based on input parameters x and n (n
> 0):
function power(x, n : byte) : longint;
var i : byte;
begin
i := 0; result := 1;
if n > 0 then
for i := 1 to n do result := result*x;
end;
Now we could call it to calculate 312 for example:
tmp := power(3, 12);
PROCEDURES
Procedure is declared like this:
procedure procedure_name(parameter_list);
{ local declarations }
begin
{ procedure body }
end;
procedure_name represents a procedure’s name and can be any valid identifier.
Within parentheses, parameter_list is a formal parameter list very similar to variable declaration. In Pascal, parameters are always passed to a procedure by the
value — to pass an argument by address, add the keyword var ahead of identifier.
Local declarations are optional declaration of variables and/or constants, local for
the given procedure. Procedure body is a sequence of statements to be executed
upon calling the procedure.
160
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
Calling a procedure
A procedure is called by its name, with actual arguments placed in the same
sequence as their matching formal parameters. The compiler is able to coerce mismatching arguments to the proper type according to implicit conversion rules. Upon
procedure call, all formal parameters are created as local objects initialized by the
values of actual arguments.
Procedure call is a self-contained statement.
Example
Here’s an example procedure which transforms its input time parameters, preparing
them for output on Lcd:
procedure
begin
sec :=
min :=
hr
:=
end;
time_prep(var sec, min, hr : byte);
((sec and $F0) shr 4)*10 + (sec and $0F);
((min and $F0) shr 4)*10 + (min and $0F);
((hr and $F0) shr 4)*10 + (hr and $0F);
A function can return a complex type. Follow the example bellow to learn how to
declare and use a function which returns a complex type.
Example:
This example shows how to declare a function which returns a complex type.
program Example;
type TCircle = record // Record
CenterX, CenterY: word;
Radius: byte;
end;
var MyCircle: TCircle; // Global variable
function DefineCircle(x, y: word; r: byte): TCircle; // DefineCircle
function returns a Record
begin
result.CenterX := x;
result.CenterY := y;
result.Radius := r;
end;
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
161
CHAPTER 6
Language Reference
mikroPASCAL PRO for PIC
begin
MyCircle := DefineCircle(100, 200, 30);
//
Get a Record via function call
MyCircle.CenterX := DefineCircle(100, 200, 30).CenterX + 20; //
Access a Record field via function call
//
|-----------------------| |-----|
//
|
|
//
Function returns TCircle
Access to one
field of TCircle
end.
Forward declaration
A function can be declared without having it followed by it's implementation, by having it followed by the forward procedure. The effective implementation of that function must follow later in the unit. The function can be used after a forward declaration as if it had been implemented already. The following is an example of a forward
declaration:
program Volume;
var Volume : word;
function First(a, b : word) : word; forward;
function Second(c : word) : word;
var tmp : word;
begin
tmp := First(2, 3);
result := tmp * c;
end;
function First(a, b : word) : word;
begin
result := a * b;
end;
begin
Volume := Second(4);
end.
Functions reentrancy
Functions reentrancy is allowed. Remember that the PIC has memory limitations
that can vary between MCUs.
162
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
TYPES
Pascal is strictly typed language, which means that every variable and constant
need to have a strictly defined type, known at the time of compilation.
The type serves:
- to determine correct memory allocation required,
- to interpret the bit patterns found in the object during subsequent accesses,
- in many type-checking situations, to ensure that illegal assignments are trapped.
mikroPascal PRO for PIC supports many standard (predefined) and user-defined
data types, including signed and unsigned integers of various sizes, arrays, strings,
pointers and records.
Type Categories
Types can be divided into:
-
simple types
arrays
strings
pointers
records
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
163
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
SIMPLE TYPES
Simple types represent types that cannot be divided into more basic elements and
are the model for representing elementary data on machine level. Basic memory
unit in mikroPascal PRO for PIC has 16 bits.
Here is an overview of simple types in mikroPascal PRO for PIC:
Type
Size
Range
byte, char
8–bit
0 .. 255
short
8–bit
-127 .. 128
word
16–bit
0 .. 65535
integer
16–bit
-32768 .. 32767
dword
32–bit
0 .. 4294967295
longint
32–bit
-2147483648 .. 2147483647
real
32–bit
±1.17549435082 * 10-38 ..
±6.80564774407 * 1038
bit
1–bit
0 or 1
sbit
1–bit
0 or 1
You can assign signed to unsigned or vice versa only using the explicit conversion.
Refer to Types Conversions for more information.
164
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
ARRAYS
An array represents an indexed collection of elements of the same type (called the
base type). Because each element has a unique index, arrays, unlike sets, can
meaningfully contain the same value more than once.
Array Declaration
Array types are denoted by constructions in the following form:
array[index_start .. index_end] of type
Each of the elements of an array is numbered from index_start through
index_end. The specifier index_start can be omitted along with dots, in which
case it defaults to zero.
Every element of an array is of type and can be accessed by specifying array name
followed by element’s index within brackets.
Here are a few examples of array declaration:
var
weekdays : array[1..7] of byte;
samples : array[50] of word;
begin
// Now we can access elements of array variables, for example:
samples[0] := 1;
if samples[37] = 0 then ...
Constant Arrays
Constant array is initialized by assigning it a comma-delimited sequence of values
within parentheses. For example:
// Declare a constant array which holds number of days in each month:
const
MONTHS
:
array[1..12]
of
byte
=
(31,28,31,30,31,30,31,31,30,31,30,31);
The number of assigned values must not exceed the specified length. The opposite
is possible, when the trailing “excess” elements are assigned zeroes.
For more information on arrays of char, refer to Strings.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
165
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
Multi-dimensional Arrays
Multidimensional arrays are constructed by declaring arrays of array type. These
arrays are stored in memory in such way that the right most subscript changes
fastest, i.e. arrays are stored “in rows”. Here is a sample 2-dimensional array:
m : array[5] of array[10] of byte;
5x10
// 2-dimensional array of size
A variable m is an array of 5 elements, which in turn are arrays of 10 byte each. Thus,
we have a matrix of 5x10 elements where the first element is m[0][0] and last one
is m[4][9]. The first element of the 4th row would be m[3][0].
STRINGS
A string represents a sequence of characters equivalent to an array of char. It is
declared like this:
string_name : string[length]
The specifier length is a number of characters the string consists of. String is stored
internally as the given sequence of characters plus a final null character which is
introduced to terminate the string. It does not count against the string’s total length.
A null string ('') is stored as a single null character.
You can assign string literals or other strings to string variables. String on the right
side of an assignment operator has to be shorter or of equal length than the one on
the right side. For example:
var
msg1 : string[20];
msg2 : string[19];
begin
msg1 := 'This is some message';
msg2 := 'Yet another message';
msg1 := msg2; // this is ok, but vice versa would be illegal
...
Alternately, you can handle strings element–by–element. For example:
166
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
var s : string[5];
...
s := 'mik';
{
s[0] is char literal 'm'
s[1] is char literal 'i'
s[2] is char literal 'k'
s[3] is zero
s[4] is undefined
s[5] is undefined
}
Be careful when handling strings in this way, since overwriting the end of a string will
cause an unpredictable behavior.
String Concatenating
mikroPascal PRO for PIC allows you to concatenate strings by means of plus operator. This kind of concatenation is applicable to string variables/literals, character
variables/literals. For control characters, use the non-quoted hash sign and a
numeral (e.g. #13 for CR).
Here is an example:
var msg
: string[20];
res_txt : string[5];
res, channel : word;
begin
//...
// Get result of ADC
res := Adc_Read(channel);
// Create string out of numeric result
WordToStr(res, res_txt);
// Prepare message for output
msg := 'Result is ' +
// Text "Result is"
res_txt
;
// Result of ADC
//...
Note: In current version plus operator for concatenating strings will accept at most
two operands.
Note
mikroPascal PRO for PIC includes a String Library which automatizes string related tasks.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
167
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
POINTERS
A pointer is a data type which holds a memory address. While a variable accesses
that memory address directly, a pointer can be thought of as a reference to that
memory address.
To declare a pointer data type, add a carat prefix (^) before type. For example, in
order to create a pointer to an integer, write:
^integer;In order to access data at the pointer’s memory location, add a carat after
the variable name. For example, let’s declare variable p which points to a word, and
then assign value 5 to the pointed memory location:
var p : ^word;
...
p^ := 5;
A pointer can be assigned to another pointer. However, note that only the address,
not the value, is copied. Once you modify the data located at one pointer, the other
pointer, when dereferenced, also yields modified data.
Pointers to program memory space are declared using the keyword const:
program const_ptr;
// constant array will be stored in program memory
const b_array: array[5] of byte = (1,2,3,4,5);
const ptr: ^byte;
begin
ptr
P0 :=
ptr
P0 :=
end.
:= @b_array;
ptr^;
:= ptr + 3;
ptr^;
// ptr is pointer to program memory space
// ptr now points to b_array[0]
// ptr now points to b_array[3]
Function Pointers
Function pointers are allowed in mikroPascal PRO for PIC. The example shows how
to define and use a function pointer:
Example:
Example demonstrates the usage of function pointers. It is shown how to declare a
procedural type, a pointer to function and finally how to call a function via pointer.
168
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
program Example;
type TMyFunctionType = function (param1, param2: byte; param3: word)
: word; // First, define the procedural type
var
MyPtr:
^TMyFunctionType;
// This is a pointer to previously defined type
Sample: word;
function Func1(p1, p2: byte; p3: word): word;
// Now,
define few functions which will be pointed to. Make sure that parameters match the type definition
begin
result := p1 and p2 or p3;
// return something
end;
function Func2(abc: byte; def: byte; ghi: word): word;
// Another
function of the same kind. Make sure that parameters match the type
definition
begin
result := abc * def + ghi;
// return something
end;
function Func3(first, yellow: byte; monday: word): word;
// Yet
another function. Make sure that parameters match the type definition
begin
result := monday - yellow - first; // return something
end;
// main program:
begin
MyPtr := @Func1;
Sample := MyPtr^(1,
pointer, call Func1, the
MyPtr := @Func2;
Sample := MyPtr^(1,
pointer, call Func2, the
MyPtr := @Func3;
Sample := MyPtr^(1,
pointer, call Func3, the
end.
// MyPtr now points
2, 3);
// Perform function
return value is 3
// MyPtr now points
2, 3);
// Perform function
return value is 5
// MyPtr now points
2, 3);
// Perform function
return value is 0
to Func1
call via
to Func2
call via
to Func3
call via
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
169
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
@ Operator
The @ operator constructs a pointer to its operand. The following rules are applied
to @:
- If X is a variable, @X returns a pointer to X.
Note: If variable X is of array type, the @ operator will return pointer to it's first basic
element, except when the left side of the statement in which X is used is an array
pointer.
In this case, the @ operator will return pointer to array, not to it's first basic element.
program example;
var w
ptr_b
ptr_arr
arr
: word;
: ^byte;
: ^array[10] of byte;
: array[10] of byte;
begin
ptr_b
:= @arr; // @ operator will return ^byte
w
:= @arr; // @ operator will return ^byte
ptr_arr := @arr; // @ operator will return ^array[10] of byte
end.
- If F is a routine (a function or procedure), @F returns a pointer to F.
Related topics: Pointer Arithmetic
170
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
RECORDS
A record (analogous to a structure in some languages) represents a heterogeneous
set of elements. Each element is called a field. The declaration of the record type
specifies a name and type for each field. The syntax of a record type declaration is
type recordTypeName = record
fieldList1 : type1;
...
fieldListn : typen;
end;
where recordTypeName is a valid identifier, each type denotes a type, and each
fieldList is a valid identifier or a comma-delimited list of identifiers. The scope of
a field identifier is limited to the record in which it occurs, so you don’t have to worry
about naming conflicts between field identifiers and other variables.
Note: In mikroPascal PRO for PIC, you cannot use the record construction directly in variable declarations, i.e. without type.
For example, the following declaration creates a record type called TDot:
type
TDot = record
x, y : real;
end;
Each TDot contains two fields: x and y coordinates. Memory is allocated when you
declare the record, like this:
var m, n: TDot;
This variable declaration creates two instances of TDot, called m and n.
A field can be of previously defined record type. For example:
// Structure defining a circle:
type
TCircle = record
radius : real;
center : TDot;
end;
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
171
CHAPTER 6
Language Reference
mikroPASCAL PRO for PIC
Accessing Fields
You can access the fields of a record by means of dot (.) as a direct field selector. If
we have declared variables circle1 and circle2 of previously defined type
TCircle:
var circle1, circle2 : TCircle;
we could access their individual fields like this:
circle1.radius := 3.7;
circle1.center.x := 0;
circle1.center.y := 0;
Accessing the fields is possible via the with statement as well.
You can also commit assignments between complex variables, if they are of the
same type:
circle2 := circle1; // This will copy values of all fields
172
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
TYPES CONVERSIONS
Conversion of variable of one type to a variable of another type is typecasting. mikroPascal PRO for PIC supports both implicit and explicit conversions for built-in types.
Implicit Conversion
Compiler will provide an automatic implicit conversion in the following situations:
- statement requires an expression of particular type (according to language
definition), and we use an expression of different type,
- operator requires an operand of particular type, and we use an operand of
different type,
- function requires a formal parameter of particular type, and we pass it an object of
different type,
- result does not match the declared function return type.
Promotion
When operands are of different types, implicit conversion promotes the less complex type to more complex type taking the following steps:
byte/char
short
short
integer
integer
word
integer
longint
longint
real
Higher bytes of extended unsigned operand are filled with zeroes. Higher bytes of
extended signed operand are filled with bit sign (if number is negative, fill higher
bytes with one, otherwise with zeroes). For example:
var a : byte; b : word;
...
a := $FF;
b := a; // a is promoted to word, b becomes $00FF
Clipping
In assignments and statements that require an expression of particular type, destination will store the correct value only if it can properly represent the result of
expression, i.e. if the result fits in destination range.
If expression evaluates to a more complex type than expected, excess of data will
be simply clipped (higher bytes are lost).
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
173
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
var i : byte; j : word;
...
j := $FF0F;
i := j;
// i becomes $0F, higher byte $FF is lost
EXPLICIT CONVERSION
Explicit conversion can be executed at any point by inserting type keyword (byte,
word, short, integer, longint or real) ahead of an expression to be converted.
The expression must be enclosed in parentheses. Explicit conversion can be performed only on the operand right of the assignment operator.
Special case is conversion between signed and unsigned types. Explicit conversion
between signed and unsigned data does not change binary representation of data
— it merely allows copying of source to destination.
For example:
var a : byte; b : short;
...
b := -1;
a := byte(b); // a is 255, not 1
// This is because binary representation remains
// 11111111; it's just interpreted differently now
You can’t execute explicit conversion on the operand left of the assignment operator:
word(b) := a;
// Compiler will report an error
Conversions Examples
Here is an example of conversion:
var a, b, c : byte;
d : word;
...
a := 241;
b := 128;
c
c
d
174
:= a + b;
:= word(a + b);
:= a + b;
// equals 113
// equals 113
// equals 369
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
OPERATORS
Operators are tokens that trigger some computation when being applied to variables
and other objects in an expression.
There are four types of operators in mikroPascal PRO for PIC:
- Arithmetic Operators
- Bitwise Operators
- Boolean Operators
- Relational Operators
OPERATORS PRECEDENCE AND ASSOCIATIVITY
There are 4 precedence categories in mikroPascal PRO for PIC. Operators in the
same category have equal precedence with each other.
Each category has an associativity rule: left-to-right (), or right-to-left (). In the
absence of parentheses, these rules resolve the grouping of expressions with operators of equal precedence.
Precedence
Operands
Operators
4
1
@
not
+
3
2
*
/
div
shl
shr
2
2
+
-
or
1
2
=
<>
<
Associativity
mod
and
xor
>
<=
>=
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
175
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
ARITHMETIC OPERATORS
Arithmetic operators are used to perform mathematical computations. They have
numerical operands and return numerical results. Since the char operators are technically bytes, they can be also used as unsigned operands in arithmetic operations.
All arithmetic operators associate from left to right.
Operator
Operation
Operands
Result
+
addition
byte, short, word,
integer, longint,
dword, real
byte, short, word,
integer,
longint,
dword, real
-
subtraction
byte, short, word,
integer, longint,
dword, real
byte, short, word,
integer,
longint,
dword, real
*
multiplication
byte, short, word,
integer, longint,
dword, real
word,
longint,
real
/
division, floatingpoint
byte, short, word,
integer, longint,
dword, real
real
div
division, rounds
down to nearest
integer
byte, short, word,
integer, longint,
dword
byte, short, word,
integer,
longint,
dword
mod
modulus, returns
the remainder of
byte, short, word,
integer, longint,
integer division
dword
(cannot be used
with floating points)
byte, short, word,
integer,
longint,
dword
integer,
dword,
Division by Zero
If 0 (zero) is used explicitly as the second operand (i.e. x div 0), the compiler will
report an error and will not generate code.
But in case of implicit division by zero: x div y, where y is 0 (zero), the result will be the
maximum integer (i.e 255, if the result is byte type; 65536, if the result is word type, etc.).
Unary Arithmetic Operators
Operator - can be used as a prefix unary operator to change sign of a signed value.
Unary prefix operator + can be used, but it doesn’t affect data.
For example:
b := -a;
176
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
Relational Operators
Use relational operators to test equality or inequality of expressions. All relational
operators return TRUE or FALSE.
Operator
Operation
=
equal
<>
not equal
>
greater than
<
less than
>=
greater than or equal
<=
less than or equal
All relational operators associate from left to right.
Relational Operators in Expressions
Precedence of arithmetic and relational operators is designated in such a way to
allow complex expressions without parentheses to have expected meaning:
a + 5 >= c - 1.0 / e
// ? (a + 5) >= (c - (1.0 / e))
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
177
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
BITWISE OPERATORS
Use bitwise operators to modify individual bits of numerical operands. Operands
need to be either both signed or both unsigned.
Bitwise operators associate from left to right. The only exception is the bitwise complement operator not which associates from right to left.
Bitwise Operators Overview
Operator
Operation
and
bitwise AND; compares pairs of bits and generates a 1 result if both
bits are 1, otherwise it returns 0
or
bitwise (inclusive) OR; compares pairs of bits and generates a 1
result if either or both bits are 1, otherwise it returns 0
xor
bitwise exclusive OR (XOR); compares pairs of bits and generates a
1 result if the bits are complementary, otherwise it returns 0
not
bitwise complement (unary); inverts each bit
shl
bitwise shift left; moves the bits to the left, discards the far left bit and
assigns 0 to the right most bit.
shr
bitwise shift right; moves the bits to the right, discards the far right bit
and if unsigned assigns 0 to the left most bit, otherwise sign extends
Logical Operations on Bit Level
and 0
1
or
0
1
xor
0
1
not
0
1
0
1
0
0
0
0
0
0
1
0
0
1
1
0
1
1
1
1
1
1
0
Bitwise operators and, or, and xor perform logical operations on the appropriate
pairs of bits of their operands. not operator complements each bit of its operand. For
example:
178
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
$1234 and $5678
Language Reference
// equals $1230
{ because ..
$1234 : 0001 0010 0011 0100
$5678 : 0101 0110 0111 1000
---------------------------and : 0001 0010 0011 0000
.. that is, $1230 }// Similarly:
$1234 or $5678
$1234 xor $5678
not $1234
// equals $567C
// equals $444C
// equals $EDCB
Unsigned and Conversions
If a number is converted from less complex to more complex data type, the upper
bytes are filled with zeroes. If a number is converted from more complex to less
complex data type, the data is simply truncated (the upper bytes are lost).
For example:
var
...
a
b
b
{
a : byte; b : word;
:= $AA;
:= $F0F0;
:= b and a;
a is extended with zeroes; b becomes $00A0 }
Signed and Conversions
If number is converted from less complex data type to more complex, upper bytes
are filled with ones if sign bit is 1 (number is negative); upper bytes are filled with
zeroes if sign bit is 0 (number is positive). If number is converted from more complex data type to less complex, data is simply truncated (upper bytes are lost).
For example:
var
...
a
b
b
a : byte; b : word;
:= -12;
:= $70FF;
:= b and a;
{ a is sign extended, with the upper byte equal to $FF;
b becomes $70F4 }
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
179
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
Bitwise Shift Operators
Binary operators shl and shr move the bits of the left operand by a number of positions specified by the right operand, to the left or right, respectively. Right operand
has to be positive and less than 255.
With shift left (shl), left most bits are discarded, and “new” bits on the right are
assigned zeroes. Thus, shifting unsigned operand to the left by n positions is equivalent to multiplying it by 2n if all discarded bits are zero. This is also true for signed
operands if all discarded bits are equal to the sign bit.
With shift right (shr), right most bits are discarded, and the “freed” bits on the left
are assigned zeroes (in case of unsigned operand) or the value of the sign bit (in
case of signed operand). Shifting operand to the right by n positions is equivalent to
dividing it by 2n.
Boolean Operators
Although mikroPascal PRO for PIC does not support boolean type, you have
Boolean operators at your disposal for building complex conditional expressions.
These operators conform to standard Boolean logic and return either TRUE (all ones)
or FALSE (zero):
Operator
Operation
and
logical AND
or
logical OR
xor
logical exclusive OR (XOR)
not
logical negation
Boolean operators associate from left to right. Negation operator not associates
from right to left.
180
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
EXPRESSIONS
An expression is a sequence of operators, operands and punctuators that returns a
value.
The primary expressions include: literals, constants, variables and function calls.
More complex expressions can be created from primary expressions by using operators. Formally, expressions are defined recursively: subexpressions can be nested
up to the limits of memory.
Expressions are evaluated according to certain conversion, grouping, associativity
and precedence rules which depend on the operators in use, presence of parentheses and data types of the operands. The precedence and associativity of the operators are summarized in Operator Precedence and Associativity. The way operands
and subexpressions are grouped does not necessarily specify the actual order in
which they are evaluated by mikroPascal PRO for PIC.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
181
CHAPTER 6
Language Reference
mikroPASCAL PRO for PIC
STATEMENTS
Statements define algorithmic actions within a program. Each statement needs to
be terminated with a semicolon (;). In the absence of specific jump and selection
statements, statements are executed sequentially in the order of appearance in the
source code.
The most simple statements are assignments, procedure calls and jump statements. These can be combined to form loops, branches and other structured statements.
Refer to:
- Assignment Statements
- Compound Statements (Blocks)
- Conditional Statements
- Iteration Statements (Loops)
- Jump Statements
- asm Statement
ASSIGNMENT STATEMENTS
Assignment statements have the form:
variable := expression;
The statement evaluates expression and assigns its value to variable. All the rules
of implicit conversion are applied. Variable can be any declared variable or array
element, and expression can be any expression.
Do not confuse the assignment with relational operator = which tests for equality.
Also note that, although similar, the construction is not related to the declaration of
constants.
182
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
COMPOUND STATEMENTS (BLOCKS)
Compound statement, or block, is a list of statements enclosed by keywords begin
and end:
begin
statements
end;
Syntactically, a block is considered to be a single statement which is allowed to be
used when Pascal syntax requires a single statement. Blocks can be nested up to
the limits of memory.
For example, the while loop expects one statement in its body, so we can pass it a
compound statement:
while i < n do
begin
temp := a[i];
a[i] := b[i];
b[i] := temp;
i := i + 1;
end;
Conditional Statements
Conditional or selection statements select one of alternative courses of action by
testing certain values. There are two types of selection statements:
- if
- case
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
183
CHAPTER 6
Language Reference
mikroPASCAL PRO for PIC
IF STATEMENT
Use if to implement a conditional statement. The syntax of if statement has the form:
if expression then statement1 [else statement2]
If expression evaluates to true then statement1 executes. If expression is false
then statement2 executes. The expression must convert to a boolean type; otherwise, the condition is ill-formed. The else keyword with an alternate statement
(statement2) is optional.
There should never be a semicolon before the keyword else.
Nested if statements
Nested if statements require additional attention. A general rule is that the nested
conditionals are parsed starting from the innermost conditional, with each else
bound to the nearest available if on its left:
if expression1 then
if expression2 then statement1
else statement2
The compiler treats the construction in this way:
if expression1 then
begin
if expression2 then statement1
else statement2
end
In order to force the compiler to interpret our example the other way around, we
have to write it explicitly:
if expression1 then
begin
if expression2 then statement1
end
else statement2
184
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
CASE STATEMENT
Use the case statement to pass control to a specific program branch, based on a
certain condition. The case statement consists of a selector expression (a condition)
and a list of possible values. The syntax of the case statement is:
case selector of
value_1 : statement_1
...
value_n : statement_n
[else default_statement]
end;
selector is an expression which should evaluate as integral value. values can be
literals, constants, or expressions, and statements can be any statements.
The else clause is optional. If using the else branch, note that there should never
be a semicolon before the keyword else.
First, the selector expression (condition) is evaluated. Afterwards the case statement compares it against all available values. If the match is found, the statement
following the match evaluates, and the case statement terminates. In case there are
multiple matches, the first matching statement will be executed. If none of values
matches selector, then default_statement in the else clause (if there is some)
is executed.
Here’s a simple example of the case statement:
case operator of
'*' : result :=
'/' : result :=
'+' : result :=
'-' : result :=
else result := 0;
end;
n1
n1
n1
n1
*
/
+
-
n2;
n2;
n2;
n2
Also, you can group values together for a match. Simply separate the items by commas:
case reg of
0:
opmode := 0;
1,2,3,4: opmode := 1;
5,6,7:
opmode := 2;
end;
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
185
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
In mikroPascal PRO for PIC, values in the case statement can be variables too:
case byte_variable of
byte_var1: opmode := 0;
// this will be compiled correctly
byte_var2:
opmode := 1;
// avoid this case, compiler will parse
// a variable followed by colon sign as
byte_var3: //
problem
opmode := 2;
end;
adding a comment solves the parsing
label
Nested Case statement
Note that the case statements can be nested – values are then assigned to the
innermost enclosing case statement.
186
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
ITERATION STATEMENTS
Iteration statements let you loop a set of statements. There are three forms of iteration statements in mikroPascal PRO for PIC:
- for
- while
- repeat
You can use the statements break and continue to control the flow of a loop statement. break terminates the statement in which it occurs, while continue begins executing the next iteration of the sequence.
For Statement
The for statement implements an iterative loop and requires you to specify the number of iterations. The syntax of the for statement is:
for counter := initial_value to final_value do statement
// or
for counter := initial_value downto final_value do statement
counter is a variable which increments (or decrements if you use downto) with each
iteration of the loop. Before the first iteration, counter is set to initial_value and
will increment (or decrement) until it reaches final_value. With each iteration,
statement will be executed.
initial_value and final_value should be expressions compatible with counter;
statement can be any statement that does not change the value of counter.
Here is an example of calculating scalar product of two vectors, a and b, of length
n, using the for statement:
s := 0;
for i := 0 to n-1 do
s := s + a[i] * b[i];
Endless Loop
The for statement results in an endless loop if final_value equals or exceeds the
range of the counter’s type.
More legible way to create an endless loop in Pascal is to use the statement while
TRUE do.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
187
CHAPTER 6
Language Reference
mikroPASCAL PRO for PIC
WHILE STATEMENT
Use the while keyword to conditionally iterate a statement. The syntax of the while
statement is:
while expression do statement
statement is executed repeatedly as long as expression evaluates true. The test
takes place before the statement is executed. Thus, if expression evaluates false
on the first pass, the loop does not execute.
Here is an example of calculating scalar product of two vectors, using the while
statement:
s := 0; i := 0;
while i < n do
begin
s := s + a[i] * b[i];
i := i + 1;
end;
Probably the easiest way to create an endless loop is to use the statement:
while TRUE do ...;
REPEAT STATEMENT
The repeat statement executes until the condition becomes false. The syntax of the
repeat statement is:
repeat statement until expression
statement is executed repeatedly as long as expression evaluates true. The
expression is evaluated after each iteration, so the loop will execute statement at
least once.
Here is an example of calculating scalar product of two vectors, using the repeat
statement:
s := 0; i := 0;
...
repeat
begin
s := s + a[i] * b[i];
i := i + 1;
end;
until i = n;
188
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
JUMP STATEMENTS
A jump statement, when executed, transfers control unconditionally. There are four
such statements in mikroPascal PRO for PIC:
-
break
continue
exit
goto
BREAK AND CONTINUE STATEMENTS
Break Statement
Sometimes, you might need to stop the loop from within its body. Use the break
statement within loops to pass control to the first statement following the innermost
loop (for, while, or repeat block).
For example:
Lcd_Out(1,1,'Insert CF card');
// Wait for CF card to be plugged; refresh every second
while TRUE do
begin
if Cf_Detect() = 1 then break;
Delay_ms(1000);
end;
// Now we can work with CF card ...
Lcd_Out(1,1,'Card detected
');
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
189
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
Continue Statement
You can use the continue statement within loops to “skip the cycle”:
- continue statement in for loop moves program counter to the line with keyword for
- continue statement in while loop moves program counter to the line with loop
condition (top of the loop),
- continue statement in repeat loop moves program counter to the line with loop
condition (bottom of the loop).
// continue jumps
here
for i := ... do
begin
...
continue;
...
end;
// continue jumps
here
while condition do
begin
...
continue;
...
end;
repeat
begin
...
continue;
...
// continue jumps
here
until condition;
EXIT STATEMENT
The exit statement allows you to break out of a routine (function or procedure). It
passes the control to the first statement following the routine call.
Here is a simple example:
procedure Proc1();
var error: byte;
begin
... // we're doing something here
if error = TRUE then exit;
... // some code, which won't be executed if error is true
end;
Note: If breaking out of a function, return value will be the value of the local variable
result at the moment of exit.
190
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
GOTO STATEMENT
Use the goto statement to unconditionally jump to a local label — for more information, refer to Labels. Syntax of goto statement is:
goto label_name;
This will transfer control to the location of a local label specified by label_name. The
goto line can come before or after the label.
The label declaration, marked statement and goto statement must belong to the
same block. Hence it is not possible to jump into or out of a procedure or function.
You can use goto to break out from any level of nested control structures. Never
jump into a loop or other structured statement, since this can have unpredictable
effects.
Use of goto statement is generally discouraged as practically every algorithm can
be realized without it, resulting in legible structured programs. One possible application of goto statement is breaking out from deeply nested control structures:
for (...) do
begin
for (...) do
begin
...
if (disaster) then goto Error;
...
end;
end;
.
.
.
Error: // error handling code
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
191
CHAPTER 6
Language Reference
mikroPASCAL PRO for PIC
asm Statement
mikroPascal PRO for PIC allows embedding assembly in the source code by means
of the asm statement. Note that you cannot use numerals as absolute addresses for
register variables in assembly instructions. You may use symbolic names instead
(listing will display these names as well as addresses).
You can group assembly instructions with the asm keyword:
asm
block of assembly instructions
end;
Pascal comments are not allowed in embedded assembly code. Instead, you may
use one-line assembly comments starting with semicolon.
Note: Compiler doesn't expect memory banks to be changed inside the assembly
code. If the user wants to do this, then he must restore the previous bank selection.
DIRECTIVES
Directives are words of special significance which provide additional functionality
regarding compilation and output.
The following directives are available for use:
- Compiler directives for conditional compilation,
- Linker directives for object distribution in memory.
192
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
COMPILER DIRECTIVES
mikroPascal PRO for PIC treats comments beginning with a “$” immediately following an opening brace as a compiler directive; for example, {$ELSE}. The compiler
directives are not case sensitive.
You can use a conditional compilation to select particular sections of code to compile, while excluding other sections. All compiler directives must be completed in the
source file in which they have begun.
Directives $DEFINE and $UNDEFINE
Use directive $DEFINE to define a conditional compiler constant (“flag”). You can
use any identifier for a flag, with no limitations. No conflicts with program identifiers
are possible because the flags have a separate name space. Only one flag can be
set per directive.
For example:
{$DEFINE Extended_format}
Use $UNDEFINE to undefine (“clear”) previously defined flag.
Note: Pascal does not support macros; directives $DEFINE and $UNDEFINE do not create/destroy macros. They only provide flags for directive $IFDEF to check against.
Directives $IFDEF, $IFNDEF, $ELSE
Conditional compilation is carried out by the $IFDEF and $IFNDEF directives. $IFDEF
tests whether a flag is currently defined, and $IFNDEF if the flag is not defined, i.e.
whether a previous $DEFINE directive has been processed for that flag and is still in
force.
Directives $IFDEF and $IFNDEF are terminated with the $ENDIF directive, and can
have an optional $ELSE clause:
{$IFDEF flag}
<block of code>
{$ELSE}
<alternate block of code>
{$ENDIF}
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
193
CHAPTER 6
Language Reference
mikroPASCAL PRO for PIC
First, $IFDEF checks if flag is defined by means of $DEFINE. If so, only <block of
code> will be compiled. Otherwise, <alternate block of code> will be compiled.
$ENDIF ends the conditional sequence. The result of the preceding scenario is that
only one section of code (possibly empty) is passed on for further processing.
The processed section can contain further conditional clauses, nested to any depth;
each $IFDEF must be matched with a closing $ENDIF.
Unlike $IFDEF, $IFNDEF checks if flag is not defined by means of $DEFINE, thus producing the opposite results.
// Uncomment the appropriate flag for your application:
//{$DEFINE resolution10}
//{$DEFINE resolution12}
{$IFDEF resolution10}
// <code specific to 10-bit resolution>
{$ELSE}
{$IFDEF resolution12}
// <code specific to 12-bit resolution>
{$ELSE}
// <default code>
{$ENDIF}
{$ENDIF}
Include Directive $I
The $I parameter directive instructs mikroPascal PRO for PIC to include the named
text file in the compilation. In effect, the file is inserted in the compiled text right after
the {$I filename} directive. If filename does not specify a directory path, then, in
addition to searching for the file in the same directory as the current unit, mikroPascal PRO for PIC will search for file in order specified by the search paths.
To specify a filename that includes a space, surround the file name with quotation
marks: {$I "My file"}.
There is one restriction to the use of include files: An include file can't be specified
in the middle of a statement part. In fact, all statements between the begin and end
of a statement part must exist in the same source file.
Predefined Flags
The compiler sets directives upon completion of project settings, so the user doesn't need to define certain flags.
Here is an example:
194
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
{$IFDEF 16F887}
// If 16F887 MCU is selected
{$IFNDEF 18F4550} // IF 18F4550 MCU is selected
See also predefined project level defines.
LINKER DIRECTIVES
mikroPascal PRO for PIC uses internal algorithm to distribute objects within memory. If you need to have a variable or a routine at the specific predefined address, use
the linker directives absolute and org.
Note: You must specify an even address when using the linker directives.
Directive absolute
Directive absolute specifies the starting address in RAM for a variable. If the variable spans more than 1 word (16-bit), the higher words will be stored at the consecutive locations.
Directive absolute is appended to the declaration of a variable:
var x : word; absolute $32;
// Variable x will occupy 1 word (16 bits) at address $32
y : longint; absolute $34;
// Variable y will occupy 2 words at addresses $34 and $36
Be careful when using the absolute directive because you may overlap two variables by accident. For example:
var i : word; absolute $42;
// Variable i will occupy 1 word at address $42;
jj : longint; absolute $40;
// Variable will occupy 2 words at $40 and $42; thus,
// changing i changes jj at the same time and vice versa
Note: You must specify an even address when using the absolute directive.
Directive org
Directive org specifies the starting address of a routine in ROM. It is appended to
the declaration of a routine. For example:
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
195
CHAPTER 6
mikroPASCAL PRO for PIC
Language Reference
procedure proc(par : byte); org $200;
begin
// Procedure will start at address $200;
...
end;
org directive can be used with main routine too. For example:
program Led_Blinking;
procedure some_proc();
begin
...
end;
org 0x800;
begin
TRISB := 0;
// main procedure starts at 0x800
while TRUE do
begin
PORTB := 0x00;
Delay_ms(500);
PORTB := 0xFF;
Delay_ms(500);
end;
end.
Note: You must specify an even address when using the org directive.
Directive orgall
Use the orgall directive to specify the address above which all routines, constants
will be placed. Example:
begin
orgall(0x200) // All the routines, constants in main program will
be above the address 0x200
...
end.
196
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER
7
mikroPascal PRO for PIC
Libraries
mikroPascal PRO for PIC provides a set of libraries which simplify the initialization
and use of PIC compliant MCUs and their modules:
Use Library manager to include mikroPascal PRO for PIC Libraries in you project.
197
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Hardware PIC-specific Libraries
- ADC Library
- CAN Library
- CANSPI Library
- Compact Flash Library
- EEPROM Library
- Ethernet PIC18FxxJ60 Library
- Flash Memory Library
- Graphic Lcd Library
- I˛C Library
- Keypad Library
- Lcd Library
- Manchester Code Library
- Multi Media Card library
- OneWire Library
- Port Expander Library
- PS/2 Library
- PWM Library
- RS-485 Library
- Software I˛C Library
- Software SPI Library
- Software UART Library
- Sound Library
- SPI Library
- SPI Ethernet Library
- SPI Graphic Lcd Library
- SPI Lcd Library
- SPI LCD8 Library
- SPI T6963C Graphic Lcd Library
- T6963C Graphic Lcd Library
- UART Library
- USB HID Library
Miscellaneous Libraries
- Button Library
- Conversions Library
- Math Library
- String Library
- Time Library
- Trigonometry Library
See also Built-in Routines.
198
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
LIBRARY DEPENDENCIES
Certain libraries use (depend on) function and/or variables, constants defined in
other libraries.
Image below shows clear representation about these dependencies.
For example, SPI_Glcd uses
Glcd_Fonts and Port_Expander
library which uses SPI library.
This means that if you check
SPI_Glcd library in Library manager, all libraries on which it
depends will be checked too.
Related topics: Library manager,
PIC Libraries
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
199
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
HARDWARE LIBRARIES
- ADC Library
- CAN Library
- CANSPI Library
- Compact Flash Library
- EEPROM Library
- Ethernet PIC18FxxJ60 Library
- Flash Memory Library
- Graphic Lcd Library
- I˛C Library
- Keypad Library
- Lcd Library
- Manchester Code Library
- Multi Media Card library
- OneWire Library
- Port Expander Library
- PS/2 Library
- PWM Library
- RS-485 Library
- Software I˛C Library
- Software SPI Library
- Software UART Library
- Sound Library
- SPI Library
- SPI Ethernet Library
- SPI Graphic Lcd Library
- SPI Lcd Library
- SPI LCD8 Library
- SPI T6963C Graphic Lcd Library
- T6963C Graphic Lcd Library
- UART Library
- USB HID Library
200
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
ADC LIBRARY
ADC (Analog to Digital Converter) module is available with a number of PIC MCUs. Library function ADC_Read is included to provide you comfortable work with the module.
ADC_Read
Prototype
function ADC_Read(channel : byte) : word;
Initializes PIC’s internal ADC module to work with RC clock. Clock determines
the time period necessary for performing AD conversion (min 12TAD).
Returns
Parameter channel represents the channel from which the analog value is to be
acquired. Refer to the appropriate datasheet for channel-to-pin mapping.
Initializes PIC ’s internal ADC module to work with XTAL frequency prescaled by
128. Clock determines the time period necessary for performing A/D conversion.
Description
Parameter channel represents the channel from which the analog value is to be
acquired. Refer to the appropriate datasheet for channel-to-pin mapping.
Requires
Nothing.
Example
var tmp : word;
...
tmp := ADC_Read(2);
// Read analog value from channel 2
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
201
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Example
This example code reads analog value from channel 2 and displays it on PORTB
and PORTC.
program ADC_on_LEDs;
var temp_res : word;
begin
ANSEL
TRISA
ANSELH
ital I/O
TRISC
TRISB
:= 0x04;
:= 0xFF;
:= 0;
// Configure AN2 pin as analog
// PORTA is input
// Configure other AN pins as dig-
:= 0x3F;
:= 0;
while (TRUE)
begin
temp_res
version
PORTB :=
PORTC :=
bits to RC7, RC6
end;
end;
// Pins RC7, RC6 are outputs
// PORTB is output
do
:= Adc_Read(2);
// Get 10-bit results of AD con-
temp_res;
// Send lower 8 bits to PORTB
word(temp_res shr 2);
// Send 2 most significant
HW Connection
ADC HW connection
202
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
CAN LIBRARY
mikroPascal PRO for PIC provides a library (driver) for working with the CAN module.
CAN is a very robust protocol that has error detection and signalling, self–checking
and fault confinement. Faulty CAN data and remote frames are re-transmitted automatically, similar to the Ethernet.
Data transfer rates vary from up to 1 Mbit/s at network lengths below 40m to 250
Kbit/s at 250m cables, and can go even lower at greater network distances, down
to 200Kbit/s, which is the minimum bitrate defined by the standard. Cables used are
shielded twisted pairs, and maximum cable length is 1000m.
CAN supports two message formats:
- Standard format, with 11 identifier bits, and
- Extended format, with 29 identifier bits
Note: Microcontroller must be connected to CAN transceiver (MCP2551 or similar)
which is connected to CAN bus.
Library Routines
-
CANSetOperationMode
CANGetOperationMode
CANInitialize
CANSetBaudRate
CANSetMask
CANSetFilter
CANRead
CANWrite
Following routines are for the internal use by compiler only:
- RegsToCANID
- CANIDToRegs
Be sure to check CAN constants necessary for using some of the functions.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
203
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
CANSetOperationMode
Prototype
procedure CANSetOperationMode(mode : byte, wait_flag : byte);
Returns
Nothing.
Sets CAN to requested mode, i.e. copies mode to CANSTAT. Parameter mode
needs to be one of CAN_OP_MODE constants (see CAN constants).
Parameter wait_flag needs to be either 0 or $FF:
Description
- If set to $FF, this is a blocking call – the function won’t “return” until the
requested mode is set.
- If 0, this is a non-blocking call. It does not verify if CAN module is switched to
requested mode or not. Caller must use CANGetOperationMode to verify
correct operation mode before performing mode specific operation.
Requires
Microcontroller must be connected to CAN transceiver (MCP2551 or similar)
which is connected to CAN bus.
Example
CANSetOperationMode(_CAN_MODE_CONFIG, $FF);
CANGetOperationMode
Prototype
function CANGetOperationMode : byte;
Returns
Current opmode.
Description Function returns current operational mode of CAN module.
204
Requires
Microcontroller must be connected to CAN transceiver (MCP2551 or similar)
which is connected to CAN bus.
Example
if (CANGetOperationMode = _CAN_MODE_NORMAL) then
...
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
CANInitialize
Prototype
procedure CANInitialize(SJW, BRP, PHSEG1, PHSEG2, PROPSEG,
CAN_CONFIG_FLAGS : byte);
Returns
Nothing.
Initializes CAN. All pending transmissions are aborted. Sets all mask registers
to 0 to allow all messages.
Filter registers are set according to flag value:
Description
if (_CAN_CONFIG_FLAGS and _CAN_CONFIG_VALID_XTD_MSG) <> 0
// Set all filters to XTD_MSG
else if (config and CONFIG_VALID_STD_MSG) <> 0
// Set all filters to STD_MSG
else
// Set half of the filters to STD, and the rest to XTD_MSG.
Parameters:
-
SJW as defined in 18XXX8 datasheet (1–4)
BRP as defined in 18XXX8 datasheet (1–64)
PHSEG1 as defined in 18XXX8 datasheet (1–8)
PHSEG2 as defined in 18XXX8 datasheet (1–8)
PROPSEG as defined in 18XXX8 datasheet (1–8)
CAN_CONFIG_FLAGS is formed from predefined constants (see CAN constants)
CAN must be in Config mode; otherwise the function will be ignored.
Requires
Example
Microcontroller must be connected to CAN transceiver (MCP2551 or similar)
which is connected to CAN bus.
init := _CAN_CONFIG_SAMPLE_THRICE and
_CAN_CONFIG_PHSEG2_PRG_ON and
_CAN_CONFIG_STD_MSG
and
_CAN_CONFIG_DBL_BUFFER_ON and
_CAN_CONFIG_VALID_XTD_MSG and
_CAN_CONFIG_LINE_FILTER_OFF;
...
CANInitialize(1, 1, 3, 3, 1, init);
// initialize CAN
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
205
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
CANSetBaudRate
Prototype
procedure CANSetBaudRate(SJW, BRP, PHSEG1, PHSEG2, PROPSEG,
CAN_CONFIG_FLAGS : byte);
Returns
Nothing.
Sets CAN baud rate. Due to complexity of CAN protocol, you cannot simply
force a bps value. Instead, use this function when CAN is in Config mode. Refer
to datasheet for details.
Parameters:
Description -
SJW as defined in 18XXX8 datasheet (1–4)
BRP as defined in 18XXX8 datasheet (1–64)
PHSEG1 as defined in 18XXX8 datasheet (1–8)
PHSEG2 as defined in 18XXX8 datasheet (1–8)
PROPSEG as defined in 18XXX8 datasheet (1–8)
CAN_CONFIG_FLAGS is formed from predefined constants (see CAN constants)
CAN must be in Config mode; otherwise the function will be ignored.
Requires
Example
206
Microcontroller must be connected to CAN transceiver (MCP2551 or similar)
which is connected to CAN bus.
init := _CAN_CONFIG_SAMPLE_THRICE and
_CAN_CONFIG_PHSEG2_PRG_ON and
_CAN_CONFIG_STD_MSG
and
_CAN_CONFIG_DBL_BUFFER_ON and
_CAN_CONFIG_VALID_XTD_MSG and
_CAN_CONFIG_LINE_FILTER_OFF;
...
CANSetBaudRate(1, 1, 3, 3, 1, init);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
CANSetMask
Prototype
procedure CANSetMask(CAN_MASK : byte; value : longint; CAN_CONFIG_FLAGS : byte);
Returns
Nothing.
Function sets mask for advanced filtering of messages. Given value is bit
adjusted to appropriate buffer mask registers.
Parameters:
Description
- CAN_MASK is one of predefined constant values (see CAN constants)
- value is the mask register value
- CAN_CONFIG_FLAGS selects type of message to filter, either
_CAN_CONFIG_XTD_MSG or _CAN_CONFIG_STD_MSG
CAN must be in Config mode; otherwise the function will be ignored.
Requires
Microcontroller must be connected to CAN transceiver (MCP2551 or similar)
which is connected to CAN bus.
// Set all mask bits to 1, i.e. all filtered bits are relevant:
CANSetMask(_CAN_MASK_B1, -1, _CAN_CONFIG_XTD_MSG);
Example
// Note that -1 is just a cheaper way to write $FFFFFFFF.
Complement will do the trick and fill it up with ones.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
207
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
CANSetFilter
Prototype
procedure CANSetFilter(CAN_FILTER : byte; value : longint;
CAN_CONFIG_FLAGS : byte);
Returns
Nothing.
Function sets message filter. Given value is bit adjusted to appropriate buffer
mask registers.
Parameters:
Description
- CAN_FILTER is one of predefined constant values (see CAN constants)
- value is the filter register value
- CAN_CONFIG_FLAGS selects type of message to filter, either
_CAN_CONFIG_XTD_MSG or _CAN_CONFIG_STD_MSG
CAN must be in Config mode; otherwise the function will be ignored.
Requires
Example
208
Microcontroller must be connected to CAN transceiver (MCP2551 or similar)
which is connected to CAN bus.
// Set id of filter B1_F1 to 3:
CANSetFilter(_CAN_FILTER_B1_F1, 3, _CAN_CONFIG_XTD_MSG);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
CANRead
Prototype
function CANRead(var id : longint; var data : array[8] of byte;
var datalen: byte; var CAN_RX_MSG_FLAGS : byte) : byte;
Returns
Message from receive buffer or zero if no message found.
Function reads message from receive buffer. If at least one full receive buffer is
found, it is extracted and returned. If none found, function returns zero.
Parameters:
Description
-
id is message identifier
data is an array of bytes up to 8 bytes in length
datalen is data length, from 1–8.
CAN_RX_MSG_FLAGS is value formed from constants (see CAN constants)
CAN must be in mode in which receiving is possible.
Requires
Microcontroller must be connected to CAN transceiver (MCP2551 or similar)
which is connected to CAN bus.
var
rcv, rx, len : byte;
data : array[8] of byte;
id : longint;
Example
// ...
rx := 0;
// ...
rcv := CANRead(id, data, len, rx);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
209
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
CANWrite
Prototype
function CANWrite(id : longint; var data : array[8] of byte;
datalen, CAN_TX_MSG_FLAGS : byte) : byte;
Returns
Returns zero if message cannot be queued (buffer full).
If at least one empty transmit buffer is found, function sends message on queue
for transmission. If buffer is full, function returns 0.
Parameters:
Description
- id is CAN message identifier. Only 11 or 29 bits may be used depending on
message type (standard or extended)
- data is array of bytes up to 8 bytes in length
- datalen is data length from 1–8
- CAN_TX_MSG_FLAGS is value formed from constants (see CAN constants)
CAN must be in Normal mode.
Requires
Microcontroller must be connected to CAN transceiver (MCP2551 or similar)
which is connected to CAN bus.
var
tx, data : byte;
id : longint;
Example
// ...
tx := _CAN_TX_PRIORITY_0 and
_CAN_TX_XTD_FRAME;
// ...
CANWrite(id, data, 2, tx);
CAN Constants
There is a number of constants predefined in CAN library. To be able to use the library effectively, you
need to be familiar with these. You might want to check the example at the end of the chapter.
CAN_OP_MODE
CAN_OP_MODE constants define CAN operation mode. Function CANSetOperationMode expects
one of these as its argument:
const
const
const
const
const
const
210
_CAN_MODE_BITS
_CAN_MODE_NORMAL
_CAN_MODE_SLEEP
_CAN_MODE_LOOP
_CAN_MODE_LISTEN
_CAN_MODE_CONFIG
=
=
=
=
=
=
$E0;
0;
$20;
$40;
$60;
$80;
// Use it to access mode bits
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
CAN_CONFIG_FLAGS
CAN_CONFIG_FLAGS constants define flags related to CAN module configuration.
Functions CANInitialize and CANSetBaudRate expect one of these (or a bitwise
combination) as their argument:
const _CAN_CONFIG_DEFAULT
const _CAN_CONFIG_PHSEG2_PRG_BIT
const _CAN_CONFIG_PHSEG2_PRG_ON
const _CAN_CONFIG_PHSEG2_PRG_OFF
= $FF;
// 11111111
= $01;
= $FF;
= $FE;
// XXXXXXX1
// XXXXXXX0
const _CAN_CONFIG_LINE_FILTER_BIT = $02;
const _CAN_CONFIG_LINE_FILTER_ON = $FF;
const _CAN_CONFIG_LINE_FILTER_OFF = $FD;
// XXXXXX1X
// XXXXXX0X
const _CAN_CONFIG_SAMPLE_BIT
const _CAN_CONFIG_SAMPLE_ONCE
const _CAN_CONFIG_SAMPLE_THRICE
= $04;
= $FF;
= $FB;
// XXXXX1XX
// XXXXX0XX
const _CAN_CONFIG_MSG_TYPE_BIT
const _CAN_CONFIG_STD_MSG
const _CAN_CONFIG_XTD_MSG
= $08;
= $FF;
= $F7;
// XXXX1XXX
// XXXX0XXX
const _CAN_CONFIG_DBL_BUFFER_BIT
const _CAN_CONFIG_DBL_BUFFER_ON
const _CAN_CONFIG_DBL_BUFFER_OFF
= $10;
= $FF;
= $EF;
const
const
const
const
const
= $60;
= $FF; // X11XXXXX
= $DF; // X10XXXXX
= $BF; // X01XXXXX
= $9F; // X00XXXXX
_CAN_CONFIG_MSG_BITS
_CAN_CONFIG_ALL_MSG
_CAN_CONFIG_VALID_XTD_MSG
_CAN_CONFIG_VALID_STD_MSG
_CAN_CONFIG_ALL_VALID_MSG
// XXX1XXXX
// XXX0XXXX
You may use bitwise and to form config byte out of these values. For example:
init := _CAN_CONFIG_SAMPLE_THRICE and
_CAN_CONFIG_PHSEG2_PRG_ON and
_CAN_CONFIG_STD_MSG
and
_CAN_CONFIG_DBL_BUFFER_ON and
_CAN_CONFIG_VALID_XTD_MSG and
_CAN_CONFIG_LINE_FILTER_OFF;
...
CANInitialize(1, 1, 3, 3, 1, init);
// Initialize CAN
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
211
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
CAN_TX_MSG_FLAGS
CAN_TX_MSG_FLAGS are flags related to transmission of a CAN message:
const
const
const
const
const
_CAN_TX_PRIORITY_BITS
_CAN_TX_PRIORITY_0
_CAN_TX_PRIORITY_1
_CAN_TX_PRIORITY_2
_CAN_TX_PRIORITY_3
=
=
=
=
=
$03;
$FC;
$FD;
$FE;
$FF;
//
//
//
//
XXXXXX00
XXXXXX01
XXXXXX10
XXXXXX11
const _CAN_TX_FRAME_BIT
const _CAN_TX_STD_FRAME
const _CAN_TX_XTD_FRAME
= $08;
= $FF;
= $F7;
// XXXXX1XX
// XXXXX0XX
const _CAN_TX_RTR_BIT
const _CAN_TX_NO_RTR_FRAME
const _CAN_TX_RTR_FRAME
= $40;
= $FF;
= $BF;
// X1XXXXXX
// X0XXXXXX
You may use bitwise and to adjust the appropriate flags. For example:
// form value to be used with CANSendMessage:
send_config := _CAN_TX_PRIORITY_0 and
_CAN_TX_XTD_FRAME and
_CAN_TX_NO_RTR_FRAME;
...
CANSendMessage(id, data, 1, send_config);
CAN_RX_MSG_FLAGS
CAN_RX_MSG_FLAGS are flags related to reception of CAN message. If a particular bit
is set; corresponding meaning is TRUE or else it will be FALSE.
const
const
const
const
const
const
const
const
const
const
const
const
_CAN_RX_FILTER_BITS
_CAN_RX_FILTER_1
_CAN_RX_FILTER_2
_CAN_RX_FILTER_3
_CAN_RX_FILTER_4
_CAN_RX_FILTER_5
_CAN_RX_FILTER_6
_CAN_RX_OVERFLOW
_CAN_RX_INVALID_MSG
_CAN_RX_XTD_FRAME
_CAN_RX_RTR_FRAME
_CAN_RX_DBL_BUFFERED
= $07; // Use it to access filter bits
= $00;
= $01;
= $02;
= $03;
= $04;
= $05;
= $08; // Set if Overflowed; else clear
= $10; // Set if invalid; else clear
= $20; // Set if XTD message; else clear
= $40; // Set if RTR message; else clear
= $80; // Set if message was
//
hardware double-buffered
You may use bitwise and to adjust the appropriate flags. For example:
212
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
if (MsgFlag and _CAN_RX_OVERFLOW) = 0 then
...
// Receiver overflow has occurred.
// We have lost our previous message.
CAN_MASK
CAN_MASK constants define mask codes. Function CANSetMask expects one of
these as its argument:
const _CAN_MASK_B1
const _CAN_MASK_B2
= 0;
= 1;
CAN_FILTER
CAN_FILTER constants define filter codes. Function CANSetFilter expects one of
these as its argument:
const
const
const
const
const
const
_CAN_FILTER_B1_F1
_CAN_FILTER_B1_F2
_CAN_FILTER_B2_F1
_CAN_FILTER_B2_F2
_CAN_FILTER_B2_F3
_CAN_FILTER_B2_F4
=
=
=
=
=
=
0;
1;
2;
3;
4;
5;
Library Example
This is a simple demonstration of CAN Library routines usage. First node initiates
the communication with the second node by sending some data to its address. The
second node responds by sending back the data incremented by 1. First node then
does the same and sends incremented data back to second node, etc.
Code for the first CAN node:
program Can_1st;
var Can_Init_Flags, Can_Send_Flags, Can_Rcv_Flags, Rx_Data_Len
byte; // can flags
RxTx_Data : array[8] of byte;
CAN rx/tx data buffer
Rx_ID : longint;
Msg_Rcvd : byte;
const ID_1st
const ID_2nd
: longint = 12111;
: longint = 3;
:
//
// node IDs
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
213
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
begin
PORTC := 0;
TRISC := 0;
// clear PORTC
// set PORTC as output
Can_Init_Flags := 0;
Can_Send_Flags := 0;
Can_Rcv_Flags := 0;
//
// clear flags
//
Can_Send_Flags := _CAN_TX_PRIORITY_0 and
_CAN_TX_XTD_FRAME and
_CAN_TX_NO_RTR_FRAME;
// form value to be used
//
with CANWrite
Can_Init_Flags := _CAN_CONFIG_SAMPLE_THRICE and
//
form value to be used
_CAN_CONFIG_PHSEG2_PRG_ON and // with CANInit
_CAN_CONFIG_XTD_MSG and
_CAN_CONFIG_DBL_BUFFER_ON and
_CAN_CONFIG_VALID_XTD_MSG;
CANInitialize(1,3,3,3,1,Can_Init_Flags);// Initialize CAN module
CANSetOperationMode(_CAN_MODE_CONFIG,0xFF);
// set
CONFIGURATION mode
CANSetMask(_CAN_MASK_B1,-1,_CAN_CONFIG_XTD_MSG);
// set
all mask1 bits to ones
CANSetMask(_CAN_MASK_B2,-1,_CAN_CONFIG_XTD_MSG);
// set
all mask2 bits to ones
CANSetFilter(_CAN_FILTER_B2_F4,ID_2nd,_CAN_CONFIG_XTD_MSG);// set
id of filter B2_F4 to 2nd node ID
CANSetOperationMode(_CAN_MODE_NORMAL,0xFF);
RxTx_Data[0] := 9;
// set NORMAL mode
// set initial data to be sent
CANWrite(ID_1st, RxTx_Data, 1, Can_Send_Flags);// send initial message
while
(
TRUE
)
do
// endless loop
begin
Msg_Rcvd := CANRead(Rx_ID , RxTx_Data , Rx_Data_Len,
Can_Rcv_Flags); // receive message
if (((Rx_ID = ID_2nd) and Msg_Rcvd) <> 0 ) then
// if message received check id
begin
PORTC
:=
RxTx_Data[0];
// id correct, output data at PORTC
Inc(RxTx_Data[0]);
// increment received data
Delay_ms(10);
CANWrite(ID_1st, RxTx_Data, 1, Can_Send_Flags);
// send incremented data back
end;
end;
end.
214
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Code for the second CAN node:
program Can_2nd;
var Can_Init_Flags, Can_Send_Flags, Can_Rcv_Flags, Rx_Data_Len
byte; // can flags
RxTx_Data : array[8] of byte;
// can rx/tx data buffer
Rx_ID : longint;
Msg_Rcvd : byte;
// reception flag
const ID_1st : longint = 12111;
const ID_2nd : longint = 3;
// node IDs
begin
PORTC := 0;
TRISC := 0;
// clear PORTC
// set PORTC as output
Can_Init_Flags := 0;
Can_Send_Flags := 0;
Can_Rcv_Flags := 0;
:
//
// clear flags
//
Can_Send_Flags := _CAN_TX_PRIORITY_0 and // form value to be used
_CAN_TX_XTD_FRAME and //
with CANWrite
_CAN_TX_NO_RTR_FRAME;
Can_Init_Flags := _CAN_CONFIG_SAMPLE_THRICE and
form value to be used
_CAN_CONFIG_PHSEG2_PRG_ON and
with CANInit
_CAN_CONFIG_XTD_MSG and
_CAN_CONFIG_DBL_BUFFER_ON and
_CAN_CONFIG_VALID_XTD_MSG and
_CAN_CONFIG_LINE_FILTER_OFF;
//
//
CANInitialize(1,3,3,3,1,Can_Init_Flags);
// initialize external CAN module
CANSetOperationMode(_CAN_MODE_CONFIG,0xFF);
// set
CONFIGURATION mode
CANSetMask(_CAN_MASK_B1,-1,_CAN_CONFIG_XTD_MSG);
// set
all mask1 bits to ones
CANSetMask(_CAN_MASK_B2,-1,_CAN_CONFIG_XTD_MSG);
// set
all mask2 bits to ones
CANSetFilter(_CAN_FILTER_B2_F3,ID_1st,_CAN_CONFIG_XTD_MSG);// set
id of filter B2_F3 to 1st node ID
CANSetOperationMode(_CAN_MODE_NORMAL,0xFF);
// set NORMAL mode
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
215
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
while
(TRUE)
do
// endless loop
begin
Msg_Rcvd := CANRead(Rx_ID , RxTx_Data , Rx_Data_Len,
Can_Rcv_Flags); // receive message
if (((Rx_ID = ID_1st) and Msg_Rcvd) <> 0 ) then
// if message received check id
begin
PORTC
:=
RxTx_Data[0];
// id correct, output data at PORTC
inc(RxTx_Data[0]);
// increment received data
CANWrite(ID_2nd, RxTx_Data, 1, Can_Send_Flags);
// send incremented data back
end;
end;
end.
HW Connection
Example of interfacing CAN transceiver with MCU and bus
216
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
CANSPI LIBRARY
The SPI module is available with a number of the PIC compliant MCUs. The
mikroPascal PRO for PIC provides a library (driver) for working with mikroElektronika's CANSPI Add-on boards (with MCP2515 or MCP2510) via SPI interface.
The CAN is a very robust protocol that has error detection and signalization,
self–checking and fault confinement. Faulty CAN data and remote frames are retransmitted automatically, similar to the Ethernet.
Data transfer rates depend on distance. For example, 1 Mbit/s can be achieved at
network lengths below 40m while 250 Kbit/s can be achieved at network lengths
below 250m. The greater distance the lower maximum bitrate that can be achieved.
The lowest bitrate defined by the standard is 200Kbit/s. Cables used are shielded
twisted pairs.
CAN supports two message formats:
- Standard format, with 11 identifier bits and
- Extended format, with 29 identifier bits
Note:
- Consult the CAN standard about CAN bus termination resistance.
- An effective CANSPI communication speed depends on SPI and certainly is
slower than “real” CAN.
- The library uses the SPI module for communication. User must initialize SPI
module before using the SPI Graphic Lcd Library.
For MCUs with two SPI modules it is possible to initialize both of them and then
switch by using the SPI_Set_Active() routine.
- CANSPI module refers to mikroElektronika's CANSPI Add-on board connected to
SPI module of MCU.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
217
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
External dependencies of CANSPI Library
The following variables
must be defined in all
projects using CANSPI
Library:
Description:
Example :
var CanSpi_CS : sbit;
Chip Select line.
sfr; external;
var CanSpi_Rst :
Reset line.
sbit; sfr; external;
var CanSpi_CS : sbit
at RC0_bit;
var CanSpi_Rst : sbit
at RC2_bit;
var
Direction of the Chip
CanSpi_CS_Direction :
sbit; sfr; external; Select pin.
var
CanSpi_CS_Direction :
sbit at TRISC0_bit;
var
CanSpi_Rst_Direction
: sbit; sfr;
external;
var
Direction of the Reset pin. CanSpi_Rst_Direction
: sbit at TRISC2_bit;
Library Routines
-
CANSPISetOperationMode
CANSPIGetOperationMode
CANSPIInitialize
CANSPISetBaudRate
CANSPISetMask
CANSPISetFilter
CANSPIread
CANSPIWrite
The following routines are for an internal use by the library only:
- RegsToCANSPIID
- CANSPIIDToRegs
Be sure to check CANSPI constants necessary for using some of the functions.
218
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
CANSPISetOperationMode
Prototype
procedure CANSPISetOperationMode(mode: byte; WAIT: byte);
Returns
Nothing.
Sets the CANSPI module to requested mode.
Parameters :
- mode: CANSPI module operation mode. Valid values: CANSPI_OP_MODE constants (see CANSPI constants).
Description
- WAIT: CANSPI mode switching verification request. If WAIT = 0, the call is
non-blocking. The function does not verify if the CANSPI module is switched to
requested mode or not. Caller must use CANSPIGetOperationMode to verify
correct operation mode before performing mode specific operation. If
WAIT != 0, the call is blocking – the function won’t “return” until the requested
mode is set.
The CANSPI routines are supported only by MCUs with the SPI module.
Requires
Example
MCU has to be properly connected to mikroElektronika's CANSPI Extra Board
or similar hardware. See connection example at the bottom of this page.
// set the CANSPI module into configuration mode (wait inside
CANSPISetOperationMode until this mode is set)
CANSPISetOperationMode(_CANSPI_MODE_CONFIG, 0xFF);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
219
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
CANSPIGetOperationMode
Prototype
function CANSPIGetOperationMode(): byte;
Returns
Current operation mode.
The function returns current operation mode of the CANSPI module. Check
Description CANSPI_OP_MODE constants (see CANSPI constants) or device datasheet for
operation mode codes.
The CANSPI routines are supported only by MCUs with the SPI module.
Requires
Example
MCU has to be properly connected to mikroElektronika's CANSPI Extra Board
or similar hardware. See connection example at the bottom of this page.
// check whether the CANSPI module is in Normal mode and if it
is do something.
if (CANSPIGetOperationMode() = _CANSPI_MODE_NORMAL) then
begin
...
end;
CANSPIInitialize
Prototype
procedure CANSPIInitialize(SJW: byte; BRP: byte; PHSEG1: byte;
PHSEG2: byte; PROPSEG: byte; CANSPI_CONFIG_FLAGS: byte);
Returns
Nothing.
Initializes the CANSPI module.
Stand-Alone CAN controller in the CANSPI module is set to:
Description
-
Disable CAN capture
Continue CAN operation in Idle mode
Do not abort pending transmissions
Fcan clock: 4*Tcy (Fosc)
Baud rate is set according to given parameters
CAN mode: Normal
Filter and mask registers IDs are set to zero
Filter and mask message frame type is set according to CANSPI_CONFIG_FLAGS value
SAM, SEG2PHTS, WAKFIL and DBEN bits are set according to
CANSPI_CONFIG_FLAGS value.
220
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Parameters:
Description -
SJW as defined in CAN controller's datasheet
BRP as defined in CAN controller's datasheet
PHSEG1 as defined in CAN controller's datasheet
PHSEG2 as defined in CAN controller's datasheet
PROPSEG as defined in CAN controller's datasheet
CANSPI_CONFIG_FLAGS is formed from predefined constants (see CANSPI
constants)
Global variables :
Requires
CanSpi_CS: Chip Select line
CanSpi_Rst: Reset line
CanSpi_CS_Bit_Direction: Direction of the Chip Select pin
CanSpi_Rst_Bit_Direction: Direction of the Reset pin
must be defined before using this function.
The CANSPI routines are supported only by MCUs with the SPI module.
The SPI module needs to be initialized. See the SPI1_Init and
SPI1_Init_Advanced routines.
MCU has to be properly connected to mikroElektronika's CANSPI Extra Board
or similar hardware. See connection example at the bottom of this page.
// CANSPI module connections
var CanSpi_CS
: sbit at RC0_bit;
CanSpi_CS_Direction : sbit at TRISC0_bit;
CanSpi_Rst : sbit at RC2_bit;
CanSpi_Rst_Direction : sbit at TRISC2_bit;
// End CANSPI module connections
Example
var Can_Init_Flags: byte;
...
Can_Init_Flags := _CANCONFIG_SAMPLE_THRICE and // form value
to be used
_CANCONFIG_PHSEG2_PRG_ON and // with
CANSPIInitialize
_CANCONFIG_XTD_MSG
and
_CANCONFIG_DBL_BUFFER_ON and
_CANCONFIG_VALID_XTD_MSG;
...
SPI1_Init();
// initialize SPI module
CANSPIInitialize(1,3,3,3,1,Can_Init_Flags); // initialize
external CANSPI module
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
221
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
CANSPISetBaudRate
Prototype
procedure CANSPISetBaudRate(SJW: byte; BRP: byte; PHSEG1: byte;
PHSEG2: byte; PROPSEG: byte; CANSPI_CONFIG_FLAGS: byte);
Returns
Nothing.
Sets the CANSPI module baud rate. Due to complexity of the CAN protocol,
you can not simply force a bps value. Instead, use this function when the
CANSPI module is in Config mode.
SAM, SEG2PHTS and WAKFIL bits are set according to CANSPI_CONFIG_FLAGS
value. Refer to datasheet for details.
Description
Parameters:
-
SJW as defined in CAN controller's datasheet
BRP as defined in CAN controller's datasheet
PHSEG1 as defined in CAN controller's datasheet
PHSEG2 as defined in CAN controller's datasheet
PROPSEG as defined in CAN controller's datasheet
CANSPI_CONFIG_FLAGS is formed from predefined constants (see CANSPI
constants)
The CANSPI module must be in Config mode, otherwise the function will be
ignored. See CANSPISetOperationMode.
Requires
The CANSPI routines are supported only by MCUs with the SPI module.
MCU has to be properly connected to mikroElektronika's CANSPI Extra Board
or similar hardware. See connection example at the bottom of this page.
Example
222
// set required baud rate and sampling rules
var can_config_flags: byte;
...
CANSPISetOperationMode(_CANSPI_MODE_CONFIG,0xFF);
// set CONFIGURATION mode (CANSPI module mast be in config mode
for baud rate settings)
can_config_flags := _CANSPI_CONFIG_SAMPLE_THRICE and
_CANSPI_CONFIG_PHSEG2_PRG_ON and
_CANSPI_CONFIG_STD_MSG
and
_CANSPI_CONFIG_DBL_BUFFER_ON and
_CANSPI_CONFIG_VALID_XTD_MSG and
_CANSPI_CONFIG_LINE_FILTER_OFF;
CANSPISetBaudRate(1, 1, 3, 3, 1, can_config_flags);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
CANSPISetMask
Prototype
procedure CANSPISetMask(CANSPI_MASK: byte; val: longint;
CANSPI_CONFIG_FLAGS: byte);
Returns
Nothing.
Configures mask for advanced filtering of messages. The parameter value is
bit-adjusted to the appropriate mask registers.
Parameters:
- CANSPI_MASK: CANSPI module mask number. Valid values: CANSPI_MASK constants (see CANSPI constants)
Description - val: mask register value
- CANSPI_CONFIG_FLAGS: selects type of message to filter. Valid values:
_CANSPI_CONFIG_ALL_VALID_MSG,
_CANSPI_CONFIG_MATCH_MSG_TYPE and _CANSPI_CONFIG_STD_MSG,
_CANSPI_CONFIG_MATCH_MSG_TYPE and _CANSPI_CONFIG_XTD_MSG.
(see CANSPI constants)
The CANSPI module must be in Config mode, otherwise the function will be
ignored. See CANSPISetOperationMode.
Requires
The CANSPI routines are supported only by MCUs with the SPI module.
MCU has to be properly connected to mikroElektronika's CANSPI Extra Board
or similar hardware. See connection example at the bottom of this page.
// set the appropriate filter mask and message type value
CANSPISetOperationMode(_CANSPI_MODE_CONFIG,0xFF);
// set CONFIGURATION mode (CANSPI module must be in config mode
for mask settings)
Example
// Set all B1 mask bits to 1 (all filtered bits are relevant):
// Note that -1 is just a cheaper way to write 0xFFFFFFFF.
// Complement will do the trick and fill it up with ones.
CANSPISetMask(_CANSPI_MASK_B1, -1, _CANSPI_CONFIG_MATCH_MSG_TYPE
and _CANSPI_CONFIG_XTD_MSG);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
223
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
CANSPISetFilter
Prototype
procedure CANSPISetFilter(CANSPI_FILTER: byte; val: longint; CANSPI_CONFIG_FLAGS: byte);
Returns
Nothing.
Configures message filter. The parameter value is bit-adjusted to the appropriate filter registers.
Parameters:
- CANSPI_FILTER: CANSPI module filter number. Valid values: CANSPI_FILTER
constants (see CANSPI constants)
Description - val: filter register value
- CANSPI_CONFIG_FLAGS: selects type of message to filter. Valid values:
_CANSPI_CONFIG_ALL_VALID_MSG,
_CANSPI_CONFIG_MATCH_MSG_TYPE and _CANSPI_CONFIG_STD_MSG,
_CANSPI_CONFIG_MATCH_MSG_TYPE and _CANSPI_CONFIG_XTD_MSG.
(see CANSPI constants)
The CANSPI module must be in Config mode, otherwise the function will be
ignored. See CANSPISetOperationMode.
Requires
The CANSPI routines are supported only by MCUs with the SPI module.
MCU has to be properly connected to mikroElektronika's CANSPI Extra Board
or similar hardware. See connection example at the bottom of this page.
Example
// set the appropriate filter value and message type
CANSPISetOperationMode(_CANSPI_MODE_CONFIG,0xFF);
// set CONFIGURATION mode (CANSPI module must be in config mode
for filter settings)
// Set id of filter B1_F1 to 3:
CANSPISetFilter(_CANSPI_FILTER_B1_F1, 3, _CANSPI_CONFIG_XTD_MSG);
224
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
CANSPIRead
Prototype
function CANSPIRead(var id: longint; var rd_data: array[8] of
byte; data_len: byte; var CANSPI_RX_MSG_FLAGS: byte): byte;
Returns
- 0 if nothing is received
- 0xFF if one of the Receive Buffers is full (message received)
If at least one full Receive Buffer is found, it will be processed in the following way:
- Message ID is retrieved and stored to location provided by the id parameter
- Message data is retrieved and stored to a buffer provided by the rd_data parameter
- Message length is retrieved and stored to location provided by the data_len
parameter
Message flags are retrieved and stored to location provided by the
Description
CANSPI_RX_MSG_FLAGS parameter
Parameters:
-
id: message identifier storage address
rd_data: data buffer (an array of bytes up to 8 bytes in length)
data_len: data length storage address.
CANSPI_RX_MSG_FLAGS: message flags storage address
The CANSPI module must be in a mode in which receiving is possible. See
CANSPISetOperationMode.
Requires
The CANSPI routines are supported only by MCUs with the SPI module.
MCU has to be properly connected to mikroElektronika's CANSPI Extra Board
or similar hardware. See connection example at the bottom of this page.
Example
// check the CANSPI module for received messages. If any was
received do something.
var msg_rcvd, rx_flags, data_len: byte;
rd_data: array[8] of byte;
msg_id: longint;
...
CANSPISetOperationMode(_CANSPI_MODE_NORMAL,0xFF);
// set NORMAL mode (CANSPI module must be in mode in which
receive is possible)
...
rx_flags := 0;
// clear message flags
if (msg_rcvd = CANSPIRead(msg_id, rd_data, data_len, rx_flags)
begin
...
end;
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
225
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
CANSPIWrite
Prototype
function CANSPIWrite(id: longint; var wr_data: array[8] of byte;
data_len: byte; CANSPI_TX_MSG_FLAGS: byte): byte;
Returns
- 0 if all Transmit Buffers are busy
- 0xFF if at least one Transmit Buffer is available
If at least one empty Transmit Buffer is found, the function sends message in
the queue for transmission.
Parameters:
Description
- id:CAN message identifier. Valid values: 11 or 29 bit values, depending on
message type (standard or extended)
- wr_data: data to be sent (an array of bytes up to 8 bytes in length)
- data_len: data length. Valid values: 1 to 8
- CANSPI_RX_MSG_FLAGS: message flags
The CANSPI module must be in mode in which transmission is possible. See
CANSPISetOperationMode.
Requires
The CANSPI routines are supported only by MCUs with the SPI module.
MCU has to be properly connected to mikroElektronika's CANSPI Extra Board
or similar hardware. See connection example at the bottom of this page.
Example
// send message extended CAN message with the appropriate ID and
data
var tx_flags: byte;
rd_data: array[8] of byte;
msg_id: longint;
...
CANSPISetOperationMode(_CANSPI_MODE_NORMAL, 0xFF);
// set NORMAL mode (CANSPI must be in mode in which transmission
is possible)
tx_flags := _CANSPI_TX_PRIORITY_0 ands _CANSPI_TX_XTD_FRAME;
// set message flags
CANSPIWrite(msg_id, rd_data, 2, tx_flags);
CANSPI Constants
There is a number of constants predefined in the CANSPI library. You need to be familiar with them in
order to be able to use the library effectively. Check the example at the end of the chapter.
226
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
CANSPI_OP_MODE
The CANSPI_OP_MODE constants define CANSPI operation mode. Function
CANSPISetOperationMode expects one of these as it's argument:
const
_CANSPI_MODE_BITS
= 0xE0; // Use this to access opmode
_CANSPI_MODE_NORMAL = 0x00;
_CANSPI_MODE_SLEEP = 0x20;
_CANSPI_MODE_LOOP
= 0x40;
_CANSPI_MODE_LISTEN = 0x60;
_CANSPI_MODE_CONFIG = 0x80;
bits
CANSPI_CONFIG_FLAGS
The CANSPI_CONFIG_FLAGS constants define flags related to the CANSPI module
configuration.
The
functions
CANSPIInitialize,
CANSPISetBaudRate,
CANSPISetMask and CANSPISetFilter expect one of these (or a bitwise combination) as their argument:
const
_CANSPI_CONFIG_DEFAULT
_CANSPI_CONFIG_PHSEG2_PRG_BIT
_CANSPI_CONFIG_PHSEG2_PRG_ON
_CANSPI_CONFIG_PHSEG2_PRG_OFF
= 0xFF;
// 11111111
= 0x01;
= 0xFF;
= 0xFE;
// XXXXXXX1
// XXXXXXX0
_CANSPI_CONFIG_LINE_FILTER_BIT = 0x02;
_CANSPI_CONFIG_LINE_FILTER_ON = 0xFF;
_CANSPI_CONFIG_LINE_FILTER_OFF = 0xFD;
// XXXXXX1X
// XXXXXX0X
_CANSPI_CONFIG_SAMPLE_BIT
_CANSPI_CONFIG_SAMPLE_ONCE
_CANSPI_CONFIG_SAMPLE_THRICE
= 0x04;
= 0xFF;
= 0xFB;
// XXXXX1XX
// XXXXX0XX
_CANSPI_CONFIG_MSG_TYPE_BIT
_CANSPI_CONFIG_STD_MSG
_CANSPI_CONFIG_XTD_MSG
= 0x08;
= 0xFF;
= 0xF7;
// XXXX1XXX
// XXXX0XXX
_CANSPI_CONFIG_DBL_BUFFER_BIT
_CANSPI_CONFIG_DBL_BUFFER_ON
_CANSPI_CONFIG_DBL_BUFFER_OFF
= 0x10;
= 0xFF;
= 0xEF;
// XXX1XXXX
// XXX0XXXX
_CANSPI_CONFIG_MSG_BITS
_CANSPI_CONFIG_ALL_MSG
_CANSPI_CONFIG_VALID_XTD_MSG
_CANSPI_CONFIG_VALID_STD_MSG
_CANSPI_CONFIG_ALL_VALID_MSG
= 0x60;
= 0xFF;
= 0xDF;
= 0xBF;
= 0x9F;
// X11XXXXX
// X10XXXXX
// X01XXXXX
// X00XXXXX
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
227
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
You may use bitwise and to form config byte out of these values. For example:
init := _CANSPI_CONFIG_SAMPLE_THRICE
_CANSPI_CONFIG_PHSEG2_PRG_ON
_CANSPI_CONFIG_STD_MSG
_CANSPI_CONFIG_DBL_BUFFER_ON
_CANSPI_CONFIG_VALID_XTD_MSG
_CANSPI_CONFIG_LINE_FILTER_OFF;
...
CANSPIInitialize(1, 1, 3, 3, 1, init);
and
and
and
and
and
// initialize CANSPI
CANSPI_TX_MSG_FLAGS
CANSPI_TX_MSG_FLAGS are flags related to transmission of a CAN message:
const
_CANSPI_TX_PRIORITY_BITS
_CANSPI_TX_PRIORITY_0
_CANSPI_TX_PRIORITY_1
_CANSPI_TX_PRIORITY_2
_CANSPI_TX_PRIORITY_3
=
=
=
=
=
0x03;
0xFC;
0xFD;
0xFE;
0xFF;
//
//
//
//
XXXXXX00
XXXXXX01
XXXXXX10
XXXXXX11
_CANSPI_TX_FRAME_BIT
_CANSPI_TX_STD_FRAME
_CANSPI_TX_XTD_FRAME
= 0x08;
= 0xFF;
= 0xF7;
// XXXXX1XX
// XXXXX0XX
_CANSPI_TX_RTR_BIT
_CANSPI_TX_NO_RTR_FRAME
_CANSPI_TX_RTR_FRAME
= 0x40;
= 0xFF;
= 0xBF;
// X1XXXXXX
// X0XXXXXX
You may use bitwise and to adjust the appropriate flags. For example:
// form value to be used as sending message flag:
send_config := _CANSPI_TX_PRIORITY_0
and
_CANSPI_TX_XTD_FRAME
and
_CANSPI_TX_NO_RTR_FRAME;
...
CANSPIWrite(id, data, 1, send_config);
CANSPI_RX_MSG_FLAGS
CANSPI_RX_MSG_FLAGS are flags related to reception of CAN message. If a particular bit is set then corresponding meaning is TRUE or else it will be FALSE.
228
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
const
_CANSPI_RX_FILTER_BITS
_CANSPI_RX_FILTER_1
_CANSPI_RX_FILTER_2
_CANSPI_RX_FILTER_3
_CANSPI_RX_FILTER_4
_CANSPI_RX_FILTER_5
_CANSPI_RX_FILTER_6
=
=
=
=
=
=
=
0x07;// Use this to access filter bits
0x00;
0x01;
0x02;
0x03;
0x04;
0x05;
_CANSPI_RX_OVERFLOW
= 0x08; // Set if Overflowed else cleared
_CANSPI_RX_INVALID_MSG = 0x10; // Set if invalid else cleared
_CANSPI_RX_XTD_FRAME
= 0x20; // Set if XTD message else cleared
_CANSPI_RX_RTR_FRAME
= 0x40; // Set if RTR message else cleared
_CANSPI_RX_DBL_BUFFERED = 0x80; // Set if this message was hardware double-buffered
You may use bitwise and to adjust the appropriate flags. For example:
if (MsgFlag and _CANSPI_RX_OVERFLOW <> 0) then
begin
...
// Receiver overflow has occurred.
// We have lost our previous message.
end;
CANSPI_MASK
The CANSPI_MASK constants define mask codes. Function CANSPISetMask
expects one of these as it's argument:
const
_CANSPI_MASK_B1 = 0;
_CANSPI_MASK_B2 = 1;
CANSPI_FILTER
The CANSPI_FILTER constants define filter codes. Functions CANSPISetFilter
expects one of these as it's argument:
const
_CANSPI_FILTER_B1_F1
_CANSPI_FILTER_B1_F2
_CANSPI_FILTER_B2_F1
_CANSPI_FILTER_B2_F2
_CANSPI_FILTER_B2_F3
_CANSPI_FILTER_B2_F4
=
=
=
=
=
=
0;
1;
2;
3;
4;
5;
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
229
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Example
This is a simple demonstration of CANSPI Library routines usage. First node initiates the communication with the second node by sending some data to its address.
The second node responds by sending back the data incremented by 1. First node
then does the same and sends incremented data back to second node, etc.
Code for the first CANSPI node:
program Can_Spi_1st;
var Can_Init_Flags, Can_Send_Flags, Can_Rcv_Flags : byte;
// can
flags
Rx_Data_Len : byte;
// received data length in bytes
RxTx_Data
: array[8] of byte;
// can rx/tx data buffer
Msg_Rcvd : byte;
// reception flag
Tx_ID, Rx_ID : longint;
// can rx and tx ID
// CANSPI module connections
var CanSpi_CS : sbit at RC0_bit;
CanSpi_CS_Direction : sbit at TRISC0_bit;
CanSpi_Rst : sbit at RC2_bit;
CanSpi_Rst_Direction : sbit at TRISC2_bit;
// End CANSPI module connections
begin
ANSEL := 0;
ANSELH := 0;
PORTB := 0;
TRISB := 0;
Can_Init_Flags := 0;
Can_Send_Flags := 0;
Can_Rcv_Flags := 0;
// Configure AN pins as digital I/O
//
// clear flags
//
Can_Send_Flags := _CANSPI_TX_PRIORITY_0 and //form value to be used
_CANSPI_TX_XTD_FRAME and //
with CANSPIWrite
_CANSPI_TX_NO_RTR_FRAME;
Can_Init_Flags := _CANSPI_CONFIG_SAMPLE_THRICE and
value to be used
_CANSPI_CONFIG_PHSEG2_PRG_ON and
CANSPIInit
_CANSPI_CONFIG_XTD_MSG and
_CANSPI_CONFIG_DBL_BUFFER_ON and
_CANSPI_CONFIG_VALID_XTD_MSG;
230
// form
// with
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI1_Init();
//
initialize SPI module
CANSPIInitialize(1,3,3,3,1,Can_Init_Flags);
//
Initialize external CANSPI module
CANSPISetOperationMode(_CANSPI_MODE_CONFIG,0xFF);
//
set CONFIGURATION mode
CANSPISetMask(_CANSPI_MASK_B1,-1,_CANSPI_CONFIG_XTD_MSG);
// set all mask1 bits to ones
CANSPISetMask(_CANSPI_MASK_B2,-1,_CANSPI_CONFIG_XTD_MSG);
// set all mask2 bits to ones
CANSPISetFilter(_CANSPI_FILTER_B2_F4,3,_CANSPI_CONFIG_XTD_MSG);
// set id of filter B1_F1 to 3
CANSPISetOperationMode(_CANSPI_MODE_NORMAL,0xFF);
set NORMAL mode
RxTx_Data[0] := 9;
Tx_ID := 12111;
//
// set initial data to be sent
// set transmit ID
CANSPIWrite(Tx_ID, RxTx_Data, 1, Can_Send_Flags);
//
send initial message
while (TRUE) do
begin
// endless loop
Msg_Rcvd := CANSPIRead(Rx_ID , RxTx_Data , Rx_Data_Len,
Can_Rcv_Flags);
// receive message
if
((Rx_ID
=
3)
and
Msg_Rcvd)
then
// if message received check id
begin
PORTB
:=
RxTx_Data[0];
// id correct, output data at PORTB
Inc(RxTx_Data[0])
;
// increment received data
Delay_ms(10);
CANSPIWrite(Tx_ID, RxTx_Data, 1, Can_Send_Flags);
// send incremented data back
end;
end;
end.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
231
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Code for the second CANSPI node:
program Can_Spi_2nd;
var Can_Init_Flags, Can_Send_Flags, Can_Rcv_Flags : byte;
// can
flags
Rx_Data_Len : byte;
// received data length in bytes
RxTx_Data
: array[8] of byte; // CAN rx/tx data buffer
Msg_Rcvd : byte;
// reception flag
Tx_ID, Rx_ID : longint;
// can rx and tx ID
// CANSPI module connections
var CanSpi_CS : sbit at RC0_bit;
CanSpi_CS_Direction : sbit at TRISC0_bit;
CanSpi_Rst : sbit at RC2_bit;
CanSpi_Rst_Direction : sbit at TRISC2_bit;
// End CANSPI module connections
begin
232
ANSEL := 0;
Configure AN pins as digital I/O
ANSELH := 0;
PORTB := 0;
clear PORTC
TRISB := 0;
set PORTC as output
//
Can_Init_Flags := 0;
Can_Send_Flags := 0;
clear flags
Can_Rcv_Flags := 0;
//
//
Can_Send_Flags := _CANSPI_TX_PRIORITY_0 and
form value to be used
_CANSPI_TX_XTD_FRAME and
with CANSPIWrite
_CANSPI_TX_NO_RTR_FRAME;
//
Can_Init_Flags := _CANSPI_CONFIG_SAMPLE_THRICE and
Form value to be used
_CANSPI_CONFIG_PHSEG2_PRG_ON and
with CANSPIInit
_CANSPI_CONFIG_XTD_MSG and
_CANSPI_CONFIG_DBL_BUFFER_ON and
_CANSPI_CONFIG_VALID_XTD_MSG and
_CANSPI_CONFIG_LINE_FILTER_OFF;
//
//
//
//
//
//
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI1_Init();
// initialize SPI1 module
CANSPIInitialize(1,3,3,3,1,Can_Init_Flags);
// initialize
external CANSPI module
CANSPISetOperationMode(_CANSPI_MODE_CONFIG,0xFF);
// set
CONFIGURATION mode
CANSPISetMask(_CANSPI_MASK_B1,-1,_CANSPI_CONFIG_XTD_MSG);
//
set all mask1 bits to ones
CANSPISetMask(_CANSPI_MASK_B2,-1,_CANSPI_CONFIG_XTD_MSG);
//
set all mask2 bits to ones
CANSPISetFilter(_CANSPI_FILTER_B2_F3,12111,_CANSPI_CONFIG_XTD_MSG);
// set id of filter B1_F1 to 3
CANSPISetOperationMode(_CANSPI_MODE_NORMAL,0xFF);
//
set NORMAL mode
Tx_ID := 3;
// set tx ID
while (TRUE) do
// endless loop
begin
Msg_Rcvd := CANSPIRead(Rx_ID , RxTx_Data , Rx_Data_Len,
Can_Rcv_Flags); // receive message
if
((Rx_ID
=
12111)
and
Msg_Rcvd)
then
// if message received check id
begin
PORTB := RxTx_Data[0];// id correct, output data at PORTB
Inc(RxTx_Data[0]) ;
// increment received data
CANSPIWrite(Tx_ID, RxTx_Data, 1, Can_Send_Flags);
// send incremented data back
end;
end;
end.
HW Connection
Example of interfacing CAN transceiver MCP2510 with MCU via SPI interface
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
233
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
COMPACT FLASH LIBRARY
The Compact Flash Library provides routines for accessing data on Compact Flash
card (abbr. CF further in text). CF cards are widely used memory elements, commonly used with digital cameras. Great capacity and excellent access time of only
a few microseconds make them very attractive for the microcontroller applications.
In CF card, data is divided into sectors. One sector usually comprises 512 bytes.
Routines for file handling, the Cf_Fat routines, are not performed directly but successively through 512B buffer.
Note: Routines for file handling can be used only with FAT16 file system.
Note: Library functions create and read files from the root directory only.
Note: Library functions populate both FAT1 and FAT2 tables when writing to files,
but the file data is being read from the FAT1 table only; i.e. there is no recovery if
the FAT1 table gets corrupted.
Note: If MMC/SD card has Master Boot Record (MBR), the library will work with the
first available primary (logical) partition that has non-zero size. If MMC/SD card has
Volume Boot Record (i.e. there is only one logical partition and no MBRs), the library
works with entire card as a single partition. For more information on MBR, physical
and logical drives, primary/secondary partitions and partition tables, please consult
other resources, e.g. Wikipedia and similar.
Note: Before writing operation, make sure not to overwrite boot or FAT sector as it
could make your card on PC or digital camera unreadable. Drive mapping tools,
such as Winhex, can be of great assistance.
234
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
External dependencies of Compact Flash Library
The following variables
must be defined in all
projects using Compact
Flash Library:
Description:
Example :
var CF_Data_Port :
byte; sfr; external;
Compact Flash Data Port. byte at PORTD;
var CF_Data_Port :
var CF_RDY : sbit;
sfr; external;
Ready signal line.
var CF_RDY : sbit at
RB7_bit;
var CF_WE : sbit;
sfr; external;
Write Enable signal line.
var CF_WE : sbit at
RB6_bit;
var CF_OE : sbit;
sfr; external;
Output Enable signal line. RB5_bit;
var CF_CD1 : sbit;
sfr; external;
Chip Detect signal line.
var CF_CD1 : sbit at
RB4_bit;
var CF_CE1 : sbit;
sfr; external;
Chip Enable signal line.
var CF_CE1 : sbit at
RB3_bit;
var CF_A2 : sbit;
sfr; external;
Address pin 2.
var CF_A2 : sbit at
RB2_bit;
var CF_A1 : sbit;
sfr; external;
Address pin 1.
var CF_A1 : sbit at
RB1_bit;
var CF_A0 : sbit;
sfr; external;
Address pin 0.
var CF_A0 : sbit at
RB0_bit;
var CF_OE : sbit at
var CF_RDY_direction :
var CF_RDY_direction
Direction of the Ready pin. : sbit at TRISB7_bit;
sbit; sfr; external;
var CF_WE_direction : Direction of the Write
sbit; sfr; external; Enable pin.
var CF_WE_direction :
sbit at TRISB6_bit;
var CF_OE_direction : Direction of the Output
sbit; sfr; external; Enable pin.
var CF_OE_direction :
sbit at TRISB5_bit;
var CF_CD1_direction : Direction of the Chip
sbit; sfr; external;
Detect pin.
var CF_CD1_direction
: sbit at TRISB4_bit;
var CF_CE1_direction : Direction of the Chip
sbit; sfr; external;
Enable pin.
var CF_CE1_direction
: sbit at TRISB3_bit;
var CF_A2_direction : Direction of the Address 2
sbit; sfr; external; pin.
var CF_A2_direction :
sbit at TRISB2_bit;
var CF_A1_direction : Direction of the Address 1
sbit; sfr; external; pin.
var CF_A1_direction :
sbit at TRISB1_bit;
var CF_A0_direction : Direction of the Address 0
sbit; sfr; external; pin.
var CF_A0_direction :
sbit at TRISB0_bit;
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
235
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Routines
-
Cf_Init
Cf_Detect
Cf_Enable
Cf_Disable
Cf_Read_Init
Cf_Read_Byte
Cf_Write_Init
Cf_Write_Byte
Cf_Read_Sector
Cf_Write_Sector
Routines for file handling:
-
236
Cf_Fat_Init
Cf_Fat_QuickFormat
Cf_Fat_Assign
Cf_Fat_Reset
Cf_Fat_Read
Cf_Fat_Rewrite
Cf_Fat_Append
Cf_Fat_Delete
Cf_Fat_Write
Cf_Fat_Set_File_Date
Cf_Fat_Get_File_Date
Cf_Fat_Get_File_Size
Cf_Fat_Get_Swap_File
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Cf_Init
Prototype
procedure Cf_Init();
Returns
Nothing.
Description Initializes ports appropriately for communication with CF card.
Global variables :
Requires
-
CF_Data_Port : Compact Flash data port
CF_RDY : Ready signal line
CF_WE : Write enable signal line
CF_OE : Output enable signal line
CF_CD1 : Chip detect signal line
CF_CE1 : Enable signal line
CF_A2 : Address pin 2
CF_A1 : Address pin 1
CF_A0 : Address pin 0
CF_RDY_direction : Direction of the Ready pin
CF_WE_direction : Direction of the Write enable pin
CF_OE_direction : Direction of the Output enable pin
CF_CD1_direction : Direction of the Chip detect pin
CF_CE1_direction : Direction of the Chip enable pin
CF_A2_direction : Direction of the Address 2 pin
CF_A1_direction : Direction of the Address 1 pin
CF_A0_direction : Direction of the Address 0 pin
must be defined before using this function.
// set compact flash pinout
var CF_Data_Port : byte at PORTD;
var
var
var
var
var
var
var
var
Example
CF_RDY
CF_WE
CF_OE
CF_CD1
CF_CE1
CF_A2
CF_A1
CF_A0
:
:
:
:
:
:
:
:
sbit
sbit
sbit
sbit
sbit
sbit
sbit
sbit
at
at
at
at
at
at
at
at
var CF_RDY_direction
var CF_WE_direction
var CF_OE_direction
var CF_CD1_direction
var CF_CE1_direction
var CF_A2_direction
var CF_A1_direction
var CF_A0_direction
// end of cf pinout
RB7_bit;
RB6_bit;
RB5_bit;
RB4_bit;
RB3_bit;
RB2_bit;
RB1_bit;
RB0_bit;
:
:
:
:
:
:
:
:
sbit
sbit
sbit
sbit
sbit
sbit
sbit
sbit
at
at
at
at
at
at
at
at
TRISB7_bit;
TRISB6_bit;
TRISB5_bit;
TRISB4_bit;
TRISB3_bit;
TRISB2_bit;
TRISB1_bit;
TRISB0_bit;
// Init CF
begin
Cf_Init();
end;
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
237
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Cf_Detect
Prototype
function CF_Detect() : byte;
Returns
- 1 - if CF card was detected
- 0 - otherwise
Description Checks for presence of CF card by reading the chip detect pin.
Requires
The corresponding MCU ports must be appropriately initialized for CF card. See
Cf_Init.
Example
// Wait until CF card is inserted:
while (Cf_Detect() = 0) do
nop;
Cf_Enable
Prototype
procedure Cf_Enable();
Returns
Nothing.
Enables the device. Routine needs to be called only if you have disabled the
Description device by means of the Cf_Disable routine. These two routines in conjunction
allow you to free/occupy data line when working with multiple devices.
Requires
The corresponding MCU ports must be appropriately initialized for CF card. See
Cf_Init.
Example
// enable compact flash
Cf_Enable();
Cf_Disable
Prototype
procedure Cf_Disable();
Returns
Nothing.
Routine disables the device and frees the data lines for other devices. To
Description enable the device again, call Cf_Enable. These two routines in conjunction
allow you to free/occupy data line when working with multiple devices.
238
Requires
The corresponding MCU ports must be appropriately initialized for CF card. See
Cf_Init.
Example
// disable compact flash
Cf_Disable();
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Cf_Read_Init
Prototype
procedure Cf_Read_Init(address : dword; sector_count : byte);
Returns
Nothing.
Initializes CF card for reading.
Description
Parameters :
- address: the first sector to be prepared for reading operation.
- sector_count: number of sectors to be prepared for reading operation.
Requires
The corresponding MCU ports must be appropriately initialized for CF card. See
Cf_Init.
Example
// initialize compact flash for reading from sector 590
Cf_Read_Init(590, 1);
Cf_Read_Byte
Prototype
function CF_Read_Byte() : byte;
Returns a byte read from Compact Flash sector buffer.
Returns
Note: Higher byte of the unsigned return value is cleared.
Description
Requires
Reads one byte from Compact Flash sector buffer location currently pointed to
by internal read pointers. These pointers will be autoicremented upon reading.
The corresponding MCU ports must be appropriately initialized for CF card. See
Cf_Init.
CF card must be initialized for reading operation. See Cf_Read_Init.
Example
// Read a byte from compact flash:
var data : byte;
...
data := Cf_Read_Byte();
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
239
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Cf_Write_Init
Prototype
procedure Cf_Write_Init(address : dword; sectcnt : byte);
Returns
Nothing.
Initializes CF card for writing.
Description
Parameters :
- address: the first sector to be prepared for writing operation.
- sectcnt: number of sectors to be prepared for writing operation.
Requires
The corresponding MCU ports must be appropriately initialized for CF card. See
Cf_Init.
Example
// initialize compact flash for writing to sector 590
Cf_Write_Init(590, 1);
Cf_Write_Byte
Prototype
procedure Cf_Write_Byte(data_ : byte);
Returns
Nothing.
Description
Writes a byte to Compact Flash sector buffer location currently pointed to by
writing pointers. These pointers will be autoicremented upon reading. When
sector buffer is full, its content will be transfered to appropriate flash memory
sector.
Parameters :
- data_: byte to be written.
Requires
The corresponding MCU ports must be appropriately initialized for CF card. See
Cf_Init.
CF card must be initialized for writing operation. See Cf_Write_Init.
Example
240
var data_ : byte;
...
data := 0xAA;
Cf_Write_Byte(data);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Cf_Read_Sector
Prototype
procedure Cf_Read_Sector(sector_number : dword; var buffer :
array[512] of byte);
Returns
Nothing.
Reads one sector (512 bytes). Read data is stored into buffer provided by the
buffer parameter.
Description Parameters :
- sector_number: sector to be read.
- buffer: data buffer of at least 512 bytes in length.
Requires
The corresponding MCU ports must be appropriately initialized for CF card. See
Cf_Init.
Example
// read sector 22
var data : array[512] of byte;
...
Cf_Read_Sector(22, data);
Cf_Write_Sector
Prototype
procedure Cf_Write_Sector(sector_number : dword; var buffer :
array[512] of byte);
Returns
Nothing.
Writes 512 bytes of data provided by the buffer parameter to one CF sector.
Description
Parameters :
- sector_number: sector to be written to.
- buffer: data buffer of 512 bytes in length.
Requires
The corresponding MCU ports must be appropriately initialized for CF card. See
Cf_Init.
Example
// write to sector 22
var data : array[512] of byte;
...
Cf_Write_Sector(22, data);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
241
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Cf_Fat_Init
Prototype
function Cf_Fat_Init(): byte;
Returns
- 0 - if CF card was detected and successfully initialized
- 1 - if FAT16 boot sector was not found
- 255 - if card was not detected
Description
Initializes CF card, reads CF FAT16 boot sector and extracts data needed by
the library.
Requires
Nothing.
Example
//init the FAT library
if (Cf_Fat_Init() = 0) then
begin
...
end
Cf_Fat_QuickFormat
Prototype
function Cf_Fat_QuickFormat(var cf_fat_label : string[11]) : byte;
Returns
- 0 - if CF card was detected, successfully formated and initialized
- 1 - if FAT16 format was unseccessful
- 255 - if card was not detected
Formats to FAT16 and initializes CF card.
Parameters :
Description
- cf_fat_label: volume label (11 characters in length). If less than 11
characters are provided, the label will be padded with spaces. If an empty
string is passed, the volume will not be labeled.
Note: This routine can be used instead or in conjunction with the Cf_Fat_Init
routine.
Note: If CF card already contains a valid boot sector, it will remain unchanged
(except volume label field) and only FAT and ROOT tables will be erased. Also,
the new volume label will be set.
242
Requires
Nothing.
Example
// format and initialize the FAT library
if (Cf_Fat_QuickFormat('mikroE') = 0) then
begin
...
end;
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Cf_Fat_Assign
Prototype
function Cf_Fat_Assign(var filename: array[12] of char;
file_cre_attr: byte): byte;
Returns
- 0 if file does not exist and no new file is created.
- 1 if file already exists or file does not exist but a new file is created.
Assigns file for file operations (read, write, delete...). All subsequent file operations will be applied to the assigned file.
Parameters :
- filename: name of the file that should be assigned for file operations. The file
name should be in DOS 8.3 (file_name.extension) format. The file name and
extension will be automatically padded with spaces by the library if they have
less than length required (i.e. "mikro.tx" -> "mikro .tx "), so the user does not
have to take care of that. The file name and extension are case insensitive.
The library will convert them to the proper case automatically, so the user does
not have to take care of that.
Also, in order to keep backward compatibility with the first version of this
library, file names can be entered as UPPERCASE string of 11 bytes in length
with no dot character between the file name and extension (i.e.
"MIKROELETXT" -> MIKROELE.TXT). In this case the last 3 characters of the
string are considered to be file extension.
- file_cre_attr: file creation and attributs flags. Each bit corresponds to the
appropriate file attribut:
Description
Bit
Mask
Description
0
0x01
Read Only
1
0x02
Hidden
2
0x04
System
3
0x08
Volume Label
4
0x10
Subdirectory
5
0x20
Archive
6
0x40
Device (internal use only, never found on disk)
7
0x80
File creation flag. If the file does not exist and this flag is set,
a new file with specified name will be created.
Note: Long File Names (LFN) are not supported.
Requires
CF card and CF library must be initialized for file operations. See Cf_Fat_Init.
Example
// create file with archive attribut if it does not already exist
Cf_Fat_Assign('MIKRO007.TXT',0xA0);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
243
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Cf_Fat_Reset
Prototype
procedure Cf_Fat_Reset(var size: dword);
Returns
Nothing.
Opens currently assigned file for reading.
Description
Parameters :
- size: buffer to store file size to. After file has been open for reading its size is
returned through this parameter.
CF card and CF library must be initialized for file operations. See Cf_Fat_Init.
Requires
File must be previously assigned. See Cf_Fat_Assign.
Example
var size : dword;
...
Cf_Fat_Reset(size);
Cf_Fat_Read
Prototype
procedure Cf_Fat_Read(var bdata: byte);
Returns
Nothing.
Reads a byte from currently assigned file opened for reading. Upon function
execution file pointers will be set to the next character in the file.
Description Parameters :
- bdata: buffer to store read byte to. Upon this function execution read byte is
returned through this parameter.
CF card and CF library must be initialized for file operations. See Cf_Fat_Init.
Requires
File must be previously assigned. See Cf_Fat_Assign.
File must be open for reading. See Cf_Fat_Reset.
Example
244
var character : byte;
...
Cf_Fat_Read(character);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Cf_Fat_Rewrite
Prototype
procedure Cf_Fat_Rewrite();
Returns
Nothing.
Description
Opens currently assigned file for writing. If the file is not empty its content will
be erased.
CF card and CF library must be initialized for file operations. See Cf_Fat_Init.
Requires
The file must be previously assigned. See Cf_Fat_Assign.
Example
// open file for writing
Cf_Fat_Rewrite();
Cf_Fat_Append
Prototype
procedure Cf_Fat_Append();
Returns
Nothing.
Opens currently assigned file for appending. Upon this function execution file
Description pointers will be positioned after the last byte in the file, so any subsequent file
writing operation will start from there.
CF card and CF library must be initialized for file operations. See Cf_Fat_Init.
Requires
File must be previously assigned. See Cf_Fat_Assign.
Example
// open file for appending
Cf_Fat_Append();
Cf_Fat_Delete
Prototype
procedure Cf_Fat_Delete();
Returns
Nothing.
Description Deletes currently assigned file from CF card.
CF card and CF library must be initialized for file operations. See Cf_Fat_Init.
Requires
File must be previously assigned. See Cf_Fat_Assign.
Example
// delete current file
Cf_Fat_Delete();
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
245
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Cf_Fat_Write
Prototype
procedure Cf_Fat_Write(var fdata: array[512] of byte; data_len:
word);
Returns
Nothing.
Writes requested number of bytes to currently assigned file opened for writing.
Description
Parameters :
- fdata: data to be written.
- data_len: number of bytes to be written.
CF card and CF library must be initialized for file operations. See Cf_Fat_Init.
Requires
File must be previously assigned. See Cf_Fat_Assign.
File must be open for writing. See Cf_Fat_Rewrite or Cf_Fat_Append.
Example
var file_contents : array[42] of byte;
...
Cf_Fat_Write(file_contents, 42); // write data to the assigned file
Cf_Fat_Set_File_Date
Prototype
procedure Cf_Fat_Set_File_Date(year: word; month: byte; day:
byte; hours: byte; mins: byte; seconds: byte);
Returns
Nothing.
Sets the date/time stamp. Any subsequent file writing operation will write this
stamp to currently assigned file's time/date attributs.
Parameters :
Description -
year: year attribute. Valid values: 1980-2107
month: month attribute. Valid values: 1-12
day: day attribute. Valid values: 1-31
hours: hours attribute. Valid values: 0-23
mins: minutes attribute. Valid values: 0-59
seconds: seconds attribute. Valid values: 0-59
CF card and CF library must be initialized for file operations. See Cf_Fat_Init.
Requires
File must be previously assigned. See Cf_Fat_Assign.
File must be open for writing. See Cf_Fat_Rewrite or Cf_Fat_Append.
Example
246
Cf_Fat_Set_File_Date(2005,9,30,17,41,0);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Cf_Fat_Get_File_Date
Prototype
procedure Cf_Fat_Get_File_Date(var year: word; var month: byte;
var day: byte; var hours: byte; var mins: byte);
Returns
Nothing.
Reads time/date attributes of currently assigned file.
Parameters :
- year: buffer to store year attribute to. Upon function execution year attribute is
returned through this parameter.
- month: buffer to store month attribute to. Upon function execution month
Description
attribute is returned through this parameter.
- day: buffer to store day attribute to. Upon function execution day attribute is
returned through this parameter.
- hours: buffer to store hours attribute to. Upon function execution hours
attribute is returned through this parameter.
- mins: buffer to store minutes attribute to. Upon function execution minutes
attribute is returned through this parameter.
CF card and CF library must be initialized for file operations. See Cf_Fat_Init.
Requires
File must be previously assigned. See Cf_Fat_Assign.
Example
var year : word;
month, day, hours, mins : byte;
...
Cf_Fat_Get_File_Date(year, month, day, hours, mins);
Cf_Fat_Get_File_Size
Prototype
function Cf_Fat_Get_File_Size(): dword;
Returns
Size of the currently assigned file in bytes.
Description This function reads size of currently assigned file in bytes.
CF card and CF library must be initialized for file operations. See Cf_Fat_Init.
Requires
File must be previously assigned. See Cf_Fat_Assign.
Example
var my_file_size : dword;
...
my_file_size := Cf_Fat_Get_File_Size();
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
247
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Cf_Fat_Get_Swap_File
Prototype
function Cf_Fat_Get_Swap_File(sectors_cnt: longint; var filename
: string[11]; file_attr : byte): dword;
Returns
- Number of the start sector for the newly created swap file, if there was enough
free space on CF card to create file of required size.
- 0 - otherwise.
This function is used to create a swap file of predefined name and size on the
CF media. If a file with specified name already exists on the media, search for
consecutive sectors will ignore sectors occupied by this file. Therefore, it is recommended to erase such file if it exists before calling this function. If it is not
erased and there is still enough space for a new swap file, this function will
delete it after allocating new memory space for a new swap file.
The purpose of the swap file is to make reading and writing to CF media as fast
as possible, by using the Cf_Read_Sector() and Cf_Write_Sector() functions
directly, without potentially damaging the FAT system. The swap file can be considered as a "window" on the media where the user can freely write/read data.
Its main purpose in the mikroPascal's library is to be used for fast data acquisition; when the time-critical acquisition has finished, the data can be re-written
into a "normal" file, and formatted in the most suitable way.
Parameters:
Description
- sectors_cnt: number of consecutive sectors that user wants the swap file to
have.
- filename: name of the file that should be assigned for file operations. The file
name should be in DOS 8.3 (file_name.extension) format. The file name and
extension will be automatically padded with spaces by the library if they have
less than length required (i.e. "mikro.tx" -> "mikro .tx "), so the user does not
have to take care of that. The file name and extension are case insensitive.
The library will convert them to the proper case automatically, so the user does
not have to take care of that.
Also, in order to keep backward compatibility with the first version of this
library, file names can be entered as UPPERCASE string of 11 bytes in length
with no dot character between the file name and extension (i.e.
"MIKROELETXT" -> MIKROELE.TXT). In this case the last 3 characters of the
string are considered to be file extension.
- file_attr: file creation and attributs flags. Each bit corresponds to the
appropriate file attribut:
248
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Description
Libraries
Bit
Mask
Description
0
0x01
Read Only
1
0x02
Hidden
2
0x04
System
3
0x08
Volume Label
4
0x10
Subdirectory
5
0x20
Archive
6
0x40
Device (internal use only, never found on disk)
7
0x80
Not used
Note: Long File Names (LFN) are not supported.
Requires
Example
CF card and CF library must be initialized for file operations. See Cf_Fat_Init.
// Try to create a swap file with archive atribute, whose size
will be at least 1000 sectors.
//
If it succeeds, it sends the No. of start sector over UART
var size : dword;
...
size := Cf_Fat_Get_Swap_File(1000, "mikroE.txt", 0x20);
if (size <> 0) then
begin
UART1_Write(0xAA);
UART1_Write(Lo(size));
UART1_Write(Hi(size));
UART1_Write(Higher(size));
UART1_Write(Highest(size));
UART1_Write(0xAA);
end
...
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
249
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Example
The following example demonstrates various aspects of the Cf_Fat16 library :
Creation of new file and writing down to it; Opening existing file and re-writing it (writing from start-of-file); Opening existing file and appending data to it (writing from
end-of-file); Opening a file and reading data from it (sending it to USART terminal);
Creating and modifying several files at once;
program CF_Fat16_Test;
var
// set compact flash pinout
Cf_Data_Port : byte at PORTD;
CF_RDY
CF_WE
CF_OE
CF_CD1
CF_CE1
CF_A2
CF_A1
CF_A0
:
:
:
:
:
:
:
:
sbit
sbit
sbit
sbit
sbit
sbit
sbit
sbit
at
at
at
at
at
at
at
at
RB7_bit;
RB6_bit;
RB5_bit;
RB4_bit;
RB3_bit;
RB2_bit;
RB1_bit;
RB0_bit;
CF_RDY_direction : sbit
CF_WE_direction : sbit
CF_OE_direction : sbit
CF_CD1_direction : sbit
CF_CE1_direction : sbit
CF_A2_direction : sbit
CF_A1_direction : sbit
CF_A0_direction : sbit
// end of cf pinout
at
at
at
at
at
at
at
at
TRISB7_bit;
TRISB6_bit;
TRISB5_bit;
TRISB4_bit;
TRISB3_bit;
TRISB2_bit;
TRISB1_bit;
TRISB0_bit;
const LINE_LEN = 39;
var
err_txt : string[20];
file_contents : string[LINE_LEN];
filename : string[14];
// File names
character : byte;
loop, loop2 : byte;
i, size : longint;
Buffer : array[512] of byte;
// UART write text and new line (carriage return + line feed)
procedure UART1_Write_Line( var uart_text : byte );
250
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
begin
UART1_Write_Text(uart_text);
UART1_Write(13);
UART1_Write(10);
end;
//-------------- Creates new file and writes some data to it
procedure M_Create_New_File();
begin
filename[7] := 'A';
Cf_Fat_Assign(filename, 0xA0);
// Will not find file and then
create file
Cf_Fat_Rewrite();
// To clear file and start with new data
for loop:=1 to 90 do
// We want 5 files on the MMC card
begin
UART1_Write('.');
file_contents[0] := loop div 10 + 48;
file_contents[1] := loop mod 10 + 48;
Cf_Fat_Write(file_contents, LINE_LEN-1);
// write data to
the assigned file
end;
end;
//-------------- Creates many new files and writes data to them
procedure M_Create_Multiple_Files();
begin
for loop2 := 'B' to 'Z' do
begin
UART1_Write(loop2); // this line can slow down the performance
filename[7] := loop2;
// set filename
Cf_Fat_Assign(filename, 0xA0);
// find existing file
or create a new one
Cf_Fat_Rewrite(); // To clear file and start with new data
for loop := 1 to 44 do
begin
file_contents[0] := loop div 10 + 48;
file_contents[1] := loop mod 10 + 48;
Cf_Fat_Write(file_contents, LINE_LEN-1); // write data to
the assigned file
end;
end;
end;
//-------------- Opens an existing file and rewrites it
procedure M_Open_File_Rewrite();
begin
filename[7] := 'C';
// Set filename for single-file tests
Cf_Fat_Assign(filename, 0);
Cf_Fat_Rewrite();
for loop := 1 to 55 do
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
251
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
begin
file_contents[0] := byte(loop div 10 + 48);
file_contents[1] := byte(loop mod 10 + 48);
Cf_Fat_Write(file_contents, LINE_LEN-1); // write data to the
assigned file
end;
end;
//-------------- Opens an existing file and appends data to it
//
(and alters the date/time stamp)
procedure M_Open_File_Append();
begin
filename[7] := 'B';
Cf_Fat_Assign(filename, 0);
Cf_Fat_Set_File_Date(2005,6,21,10,35,0);
Cf_Fat_Append();
file_contents := ' for mikroElektronika 2005';
// Prepare file
for append
end;
//-------------- Opens an existing file, reads data from it and puts
it to USART
procedure M_Open_File_Read();
begin
filename[7] := 'B';
Cf_Fat_Assign(filename, 0);
Cf_Fat_Reset(size);
// To read file, procedure returns
size of file
while size > 0 do
begin
Cf_Fat_Read(character);
UART1_Write(character);
// Write data to USART
Dec(size);
end;
end;
//-------------- Deletes a file. If file doesn't exist, it will first
be created
//
and then deleted.
procedure M_Delete_File();
begin
filename[7] := 'F';
Cf_Fat_Assign(filename, 0);
Cf_Fat_Delete();
end;
//-------------- Tests whether file exists, and if so sends its creation date
//
and file size via USART
252
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
procedure M_Test_File_Exist();
var
fsize : longint;
year : word;
month, day, hour, minute : byte;
outstr : array[12] of byte;
begin
filename[7] := 'B';
//uncomment this line to search for file
that DOES exists
// filename[7] := 'F';
//uncomment this line to search for
file that DOES NOT exist
if Cf_Fat_Assign(filename, 0) <> 0 then
begin
//--- file has been found - get its date
Cf_Fat_Get_File_Date(year,month,day,hour,minute);
WordToStr(year, outstr);
UART1_Write_Text(outstr);
ByteToStr(month, outstr);
UART1_Write_Text(outstr);
WordToStr(day, outstr);
UART1_Write_Text(outstr);
WordToStr(hour, outstr);
UART1_Write_Text(outstr);
WordToStr(minute, outstr);
UART1_Write_Text(outstr);
//--- get file size
fsize := Cf_Fat_Get_File_Size;
LongIntToStr(fsize, outstr);
UART1_Write_Text(outstr);
end
else begin
//--- file was not found - signal it
UART1_Write(0x55);
Delay_ms(1000);
UART1_Write(0x55);
end;
end;
//-------------- Tries to create a swap file, whose size will be at
least 100
//
sectors (see Help for details)
procedure M_Create_Swap_File();
var i : word;
begin
for i:=0 to 511 do
Buffer[i] := i;
size := Cf_Fat_Get_Swap_File(5000, 'mikroE.txt', 0x20);
help on this function for details
// see
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
253
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
if (size <> 0) then
begin
LongIntToStr(size, err_txt);
UART1_Write_Line(err_txt);
for i:=0 to 4999 do
begin
Cf_Write_Sector(size, Buffer);
Inc(size);
UART1_Write('.');
end;
end;
end;
//-------------- Main. Uncomment the function(s) to test the desired
operation(s)
begin
err_txt := 'FAT16 not found';
file_contents := 'XX CF FAT16 library by Anton Rieckert';
filename := 'MIKRO00xTXT';
// we will use PORTC to signal test end
ADCON1 := ADCON1 or 0x0F; // Configure AN pins as digital
CMCON := CMCON or 7;
// Turn off comparators
UART1_Init(19200);
// Set up USART for file reading
Delay_ms(10);
UART1_Write_Line('PIC-Started');
// PIC present report
// --- Init the FAT library
// --- use Cf_Fat_QuickFormat instead of init routine if a format is needed
if Cf_Fat_Init() = 0 then
begin
Delay_ms(2000);
// wait for a while until the card is
stabilized
//
period depends on used CF card
//--- Test start
UART1_Write_Line('Test Start.');
M_Create_New_File();
M_Create_Multiple_Files();
M_Open_File_Rewrite();
M_Open_File_Append();
M_Open_File_Read();
M_Delete_File();
M_Test_File_Exist();
M_Create_Swap_File();
UART1_Write_Line('Test End.');
end
else
begin
UART1_Write_Line(err_txt);
// Note: Cf_Fat_Init tries to
initialize a card more than once.
//
If card is not
present, initialization may last longer (depending on clock speed)
end;
end.
254
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
HW Connection
Pin diagram of CF memory card
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
255
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
EEPROM LIBRARY
EEPROM data memory is available with a number of PIC MCUs. mikroPascal PRO for PIC
includes library for comfortable work with EEPROM.
Library Routines
- EEPROM_Read
- EEPROM_Write
EEPROM_Read
Prototype
function EEPROM_Read(Address: word): byte;
Returns
Returns byte from specified address.
Reads data from specified address. Parameter address is of byte type, which
means it can address only 256 locations. For PIC18 MCUs with more EEPROM
Description
data locations, it is programmer’s responsibility to set SFR EEADRH register
appropriately.
Requires EEPROM module.
Requires
Ensure minimum 20ms delay between successive use of routines
EEPROM_Write and EEPROM_Read. Although PIC will write the correct value,
EEPROM_Read might return an undefined result.
Example
tmp := EEPROM_Read($3F);
EEPROM_Write
Prototype
procedure EEPROM_Write(Address : word; Data_: byte);
Returns
Nothing.
Writes data to specified address. Parameter address is of byte type, which
means it can address only 256 locations. For PIC18 MCUs with more EEPROM
data locations, it is programmer’s responsibility to set SFR EEADRH register
Description appropriately.
Be aware that all interrupts will be disabled during execution of EEPROM_Write routine (GIE bit of INTCON register will be cleared). Routine will set this bit on exit.
Requires EEPROM module.
256
Requires
Ensure minimum 20ms delay between successive use of routines
EEPROM_Write and EEPROM_Read. Although PIC will write the correct value,
EEPROM_Read might return an undefined result.
Example
EEPROM_Write($32);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Example
The example demonstrates using EEPROM Library.
program Eeprom;
var counter : byte;
begin
ANSEL := 0;
ANSELH := 0;
// loop variable
// Configure AN pins as digital I/O
PORTB := 0;
PORTC := 0;
PORTD := 0;
TRISB := 0;
TRISC := 0;
TRISD := 0;
for counter := 0 to 31 do
EEPROM_Write(0x80+counter, counter);
0x80+ii
EEPROM_Write(0x02,0xAA);
EEPROM_Write(0x50,0x55);
Delay_ms(1000);
PORTB := 0xFF;
PORTC := 0xFF;
Delay_ms(1000);
PORTB := 0x00;
PORTC := 0x00;
Delay_ms(1000);
// Fill data buffer
// Write data to address
// Write some data at address 2
// Write some data at address 0150
// Blink PORTB and PORTC diodes
//
to indicate reading start
PORTB := EEPROM_Read(0x02);
2 and display it on PORTB
PORTC := EEPROM_Read(0x50);
0x50 and display it on PORTC
// Read data from address
// Read data from address
Delay_ms(1000);
for counter := 0 to 31 do
from address 0x100
begin
PORTD := EEPROM_Read(0x80+counter);
PORTC
Delay_ms(300);
end;
end.
// Read 32 bytes block
//
and display data on
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
257
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
ETHERNET PIC18FXXJ60 LIBRARY
PIC18FxxJ60 family of microcontrollers feature an embedded Ethernet controller
module. This is a complete connectivity solution, including full implementations of
both Media Access Control (MAC) and Physical Layer transceiver (PHY) modules.
Two pulse transformers and a few passive components are all that are required to
connect the microcontroller directly to an Ethernet network.
The Ethernet module meets all of the IEEE 802.3 specifications for 10-BaseT connectivity to a twisted-pair network. It incorporates a number of packet filtering
schemes to limit incoming packets. It also provides an internal DMA module for fast
data throughput and hardware assisted IP checksum calculations. Provisions are
also made for two LED outputs to indicate link and network activity
This library provides the posibility to easily utilize ethernet feature of the above mentioned MCUs.
Ethernet PIC18FxxJ60 library supports:
- IPv4 protocol.
- ARP requests.
- ICMP echo requests.
- UDP requests.
- TCP requests (no stack, no packet reconstruction).
- ARP client with cache.
- DNS client.
- UDP client.
- DHCP client.
- packet fragmentation is NOT supported.
Note: Global library variable Ethernet_userTimerSec is used to keep track of time
for all client implementations (ARP, DNS, UDP and DHCP). It is user responsibility
to increment this variable each second in it's code if any of the clients is used.
Note: For advanced users there are header files ("eth_j60LibDef.h" and
"eth_j60LibPrivate.h") in Uses\P18 folder of the compiler with description of all
routines and global variables, relevant to the user, implemented in the Ethernet
PIC18FxxJ60 Library.
258
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Routines
-
Ethernet_Init
Ethernet_Enable
Ethernet_Disable
Ethernet_doPacket
Ethernet_putByte
Ethernet_putBytes
Ethernet_putString
Ethernet_putConstString
Ethernet_putConstBytes
Ethernet_getByte
Ethernet_getBytes
Ethernet_UserTCP
Ethernet_UserUDP
Ethernet_getIpAddress
Ethernet_getGwIpAddress
Ethernet_getDnsIpAddress
Ethernet_getIpMask
Ethernet_confNetwork
Ethernet_arpResolve
Ethernet_sendUDP
Ethernet_dnsResolve
Ethernet_initDHCP
Ethernet_doDHCPLeaseTime
Ethernet_renewDHCP
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
259
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Ethernet_Init
Prototype
procedure Ethernet_Init(var mac : array[6] of byte; var ip :
array[4] of byte; fullDuplex : byte);
Returns
Nothing.
This is MAC module routine. It initializes Ethernet controller. This function is
internaly splited into 2 parts to help linker when coming short of memory.
Ethernet controller settings (parameters not mentioned here are set to default):
- receive buffer start address : 0x0000.
- receive buffer end address : 0x19AD.
- transmit buffer start address: 0x19AE.
- transmit buffer end address : 0x1FFF.
- RAM buffer read/write pointers in auto-increment mode.
- receive filters set to default: CRC + MAC Unicast + MAC Broadcast in OR mode.
- flow control with TX and RX pause frames in full duplex mode.
- frames are padded to 60 bytes + CRC.
- maximum packet size is set to 1518.
Description - Back-to-Back Inter-Packet Gap: 0x15 in full duplex mode; 0x12 in half duplex mode.
- Non-Back-to-Back Inter-Packet Gap: 0x0012 in full duplex mode; 0x0C12 in
half duplex mode.
- half duplex loopback disabled.
- LED configuration: default (LEDA-link status, LEDB-link activity).
Parameters:
- mac: RAM buffer containing valid MAC address.
- ip: RAM buffer containing valid IP address.
- fullDuplex: ethernet duplex mode switch. Valid values: 0 (half duplex mode,
predefined library const Ethernet_HALFDUPLEX) and 1 (full duplex mode,
predefined library const Ethernet_FULLDUPLEX).
Note: If a DHCP server is to be used, IP address should be set to 0.0.0.0.
Requires
Example
Nothing.
var
myMacAddr : array[6] of byte; // my MAC address
myIpAddr : array[4] of byte; // my IP addr
...
myMacAddr[0] := 0x00;
myMacAddr[1] := 0x14;
myMacAddr[2] := 0xA5;
myMacAddr[3] := 0x76;
myMacAddr[4] := 0x19;
myMacAddr[5] := 0x3F;
myIpAddr[0]
myIpAddr[1]
myIpAddr[2]
myIpAddr[3]
:=
:=
:=
:=
192;
168;
20;
60;
Ethernet_Init(myMacAddr, myIpAddr, Ethernet_FULLDUPLEX);
260
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Ethernet_Enable
Prototype
procedure Ethernet_Enable(enFlt : byte);
Returns
Nothing.
This is MAC module routine. This routine enables appropriate network traffic on
the MCU's internal Ethernet module by the means of it's receive filters (unicast,
multicast, broadcast, crc). Specific type of network traffic will be enabled if a
corresponding bit of this routine's input parameter is set. Therefore, more than
one type of network traffic can be enabled at the same time. For this purpose,
predefined library constants (see the table below) can be ORed to form appropriate input value.
Parameters:
- enFlt: network traffic/receive filter flags. Each bit corresponds to the
appropriate network traffic/receive filter:
Bit
Mask
0
0x01
MAC Broadcast traffic/receive filter
_Ethernet_BROADCAST
flag. When set, MAC broadcast
traffic will be enabled.
1
0x02
MAC Multicast traffic/receive filter
flag. When set, MAC multicast traf- _Ethernet_MULTICAST
fic will be enabled.
2
0x04
not used
none
3
0x08
not used
none
4
0x10
not used
none
5
0x20
CRC check flag. When set, packets with invalid CRC field will be
discarded.
_Ethernet_CRC
6
0x40
not used
none
7
0x80
MAC Unicast traffic/receive filter
flag. When set, MAC unicast traffic _Ethernet_UNICAST
will be enabled.
Description
Description
Predefined library const
Note: Advance filtering available in the MCU's internal Ethernet module such as
Pattern Match, Magic Packet and Hash Table can not be enabled by this rou-
tine. Additionaly, all filters, except CRC, enabled with this routine will work in OR
mode, which means that packet will be received if any of the enabled filters
accepts it.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
261
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Note: This routine will change receive filter configuration on-the-fly. It will not, in
any way, mess with enabling/disabling receive/transmit logic or any other part of
Description
the MCU's internal Ethernet module. The MCU's internal Ethernet module
should be properly cofigured by the means of Ethernet_Init routine.
Requires
Ethernet module has to be initialized. See Ethernet_Init.
Example
Ethernet_Enable(_Ethernet_CRC or _Ethernet_UNICAST); // enable
CRC checking and Unicast traffic
Ethernet_Disable
Prototype
procedure Ethernet_Disable(disFlt : byte);
Returns
Nothing.
This is MAC module routine. This routine disables appropriate network traffic on
the MCU's internal Ethernet module by the means of it's receive filters (unicast,
multicast, broadcast, crc). Specific type of network traffic will be disabled if a
corresponding bit of this routine's input parameter is set. Therefore, more than
one type of network traffic can be disabled at the same time. For this purpose,
predefined library constants (see the table below) can be ORed to form appropriate input value.
Parameters:
- disFlt: network traffic/receive filter flags. Each bit corresponds to the
appropriate network traffic/receive filter:
Bit Mask
Predefined library const
0
MAC Broadcast traffic/receive filter
0x01 flag. When set, MAC broadcast traffic _Ethernet_BROADCAST
will be disabled.
1
MAC Multicast traffic/receive filter
0x02 flag. When set, MAC multicast traffic
will be disabled.
_Ethernet_MULTICAST
2
0x04 not used
none
3
0x08 not used
none
4
0x10 not used
none
5
CRC check flag. When set, CRC check
0x20 will be disabled and packets with invalid _Ethernet_CRC
CRC field will be accepted.
6
0x40 not used
7
MAC Unicast traffic/receive filter flag.
0x80 When set, MAC unicast traffic will be _Ethernet_UNICAST
disabled.
Description
262
Description
none
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Note: Advance filtering available in the MCU's internal Ethernet module such as
Pattern Match, Magic Packet and Hash Table can not be disabled by this routine.
Description Note: This routine will change receive filter configuration on-the-fly. It will not, in
any way, mess with enabling/disabling receive/transmit logic or any other part of
the MCU's internal Ethernet module. The MCU's internal Ethernet module
should be properly cofigured by the means of Ethernet_Init routine.
Requires
Ethernet module has to be initialized. See Ethernet_Init.
Example
Ethernet_Disable(_Ethernet_CRC or _Ethernet_UNICAST); // disable
CRC checking and Unicast traffic
Ethernet_doPacket
Prototype
function Ethernet_doPacket() : byte;
Returns
- 0 - upon successful packet processing (zero packets received or received
packet processed successfully).
- 1 - upon reception error or receive buffer corruption. Ethernet controller needs
to be restarted.
- 2 - received packet was not sent to us (not our IP, nor IP broadcast address).
- 3 - received IP packet was not IPv4.
- 4 - received packet was of type unknown to the library.
This is MAC module routine. It processes next received packet if such exists.
Packets are processed in the following manner:
Description
- ARP & ICMP requests are replied automatically.
- upon TCP request the Ethernet_UserTCP function is called for further processing.
- upon UDP request the Ethernet_UserUDP function is called for further processing.
Note: Ethernet_doPacket must be called as often as possible in user's code.
Requires
Ethernet module has to be initialized. See Ethernet_Init.
Example
while true do
begin
...
Ethernet_doPacket(); // process received packets
...
end;
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
263
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Ethernet_putByte
Prototype
procedure Ethernet_putByte(v : byte);
Returns
Nothing.
This is MAC module routine. It stores one byte to address pointed by the current Ethernet controller's write pointer (EWRPT).
Description
Parameters:
- v: value to store
Requires
Ethernet module has to be initialized. See Ethernet_Init.
Example
var
data : byte;
...
Ethernet_putByte(data);
// put an byte into ethernet buffer
Ethernet_putBytes
Prototype
procedure Ethernet_putBytes(ptr : ^byte; n : byte);
Returns
Nothing.
This is MAC module routine. It stores requested number of bytes into Ethernet
controller's RAM starting from current Ethernet controller's write pointer (EWRPT)
location.
Description
Parameters:
- ptr: RAM buffer containing bytes to be written into Ethernet controller's RAM.
- n: number of bytes to be written.
264
Requires
Ethernet module has to be initialized. See Ethernet_Init.
Example
var
buffer : array[17] of byte;
...
buffer := 'mikroElektronika';
...
Ethernet_putBytes(buffer, 16); // put an RAM array into ethernet buffer
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Ethernet_putConstBytes
Prototype
procedure Ethernet_putConstBytes(const ptr : ^byte; n : byte);
Returns
Nothing.
This is MAC module routine. It stores requested number of const bytes into Ethernet controller's RAM starting from current Ethernet controller's write pointer
(EWRPT) location.
Description
Parameters:
- ptr: const buffer containing bytes to be written into Ethernet controller's RAM.
- n: number of bytes to be written.
Requires
Ethernet module has to be initialized. See Ethernet_Init.
Example
const
buffer : array[17] of byte;
...
buffer := 'mikroElektronika';
...
Ethernet_putConstBytes(buffer, 16); // put a const array into
ethernet buffer
Ethernet_putString
Prototype
function Ethernet_putString(ptr : ^byte) : word;
Returns
Number of bytes written into Ethernet controller's RAM.
This is MAC module routine. It stores whole string (excluding null termination)
into Ethernet controller's RAM starting from current Ethernet controller's write
pointer (EWRPT) location.
Description
Parameters:
- ptr: string to be written into Ethernet controller's RAM.
Requires
Ethernet module has to be initialized. See Ethernet_Init.
Example
var
buffer : string[16];
...
buffer := 'mikroElektronika';
...
Ethernet_putString(buffer); // put a RAM string into ethernet
buffer
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
265
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Ethernet_putConstString
Prototype
function Ethernet_putConstString(const ptr : ^byte) : word;
Returns
Number of bytes written into Ethernet controller's RAM.
This is MAC module routine. It stores whole const string (excluding null termination) into Ethernet controller's RAM starting from current Ethernet controller's
write pointer (EWRPT) location.
Description
Parameters:
- ptr: const string to be written into Ethernet controller's RAM.
Requires
Ethernet module has to be initialized. See Ethernet_Init.
Example
const
buffer : string[16];
...
buffer := 'mikroElektronika';
...
Ethernet_putConstString(buffer); // put a const string into
ethernet buffer
Ethernet_getByte
266
Prototype
function Ethernet_getByte() : byte;
Returns
Byte read from Ethernet controller's RAM.
Description
This is MAC module routine. It fetches a byte from address pointed to by current Ethernet controller's read pointer (ERDPT).
Requires
Ethernet module has to be initialized. See Ethernet_Init.
Example
var
buffer : byte;
...
buffer := Ethernet_getByte(); // read a byte from ethernet buffer
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Ethernet_getBytes
Prototype
procedure Ethernet_getBytes(ptr : ^byte; addr : word; n : byte);
Returns
Nothing.
This is MAC module routine. It fetches equested number of bytes from Ethernet
controller's RAM starting from given address. If value of 0xFFFF is passed as
the address parameter, the reading will start from current Ethernet controller's
read pointer (ERDPT) location.
Description
Parameters:
- ptr: buffer for storing bytes read from Ethernet controller's RAM.
- addr: Ethernet controller's RAM start address. Valid values: 0..8192.
- n: number of bytes to be read.
Requires
Ethernet module has to be initialized. See Ethernet_Init.
Example
var
buffer: array[16] of byte;
...
Ethernet_getBytes(buffer, 0x100, 16); // read 16 bytes, starting from address 0x100
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
267
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Ethernet_UserTCP
Prototype
function Ethernet_UserTCP(var remoteHost : array[4] of byte;
remotePort, localPort, reqLength : word) : word;
Returns
- 0 - there should not be a reply to the request.
- Length of TCP/HTTP reply data field - otherwise.
This is TCP module routine. It is internally called by the library. The user
accesses to the TCP/HTTP request by using some of the Ethernet_get routines.
The user puts data in the transmit buffer by using some of the Ethernet_put routines. The function must return the length in bytes of the TCP/HTTP reply, or 0 if
there is nothing to transmit. If there is no need to reply to the TCP/HTTP
requests, just define this function with return(0) as a single statement.
Description
Parameters:
-
remoteHost: client's IP address.
remotePort: client's TCP port.
localPort: port to which the request is sent.
reqLength: TCP/HTTP request data field length.
Note: The function source code is provided with appropriate example projects.
The code should be adjusted by the user to achieve desired reply.
268
Requires
Ethernet module has to be initialized. See Ethernet_Init.
Example
This function is internally called by the library and should not be called by the
user's code.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Ethernet_UserUDP
Prototype
function Ethernet_UserUDP(var remoteHost : array[4] of byte;
remotePort, destPort, reqLength : word) : word;
Returns
- 0 - there should not be a reply to the request.
- Length of UDP reply data field - otherwise.
This is UDP module routine. It is internally called by the library. The user
accesses to the UDP request by using some of the Ethernet_get routines. The
user puts data in the transmit buffer by using some of the Ethernet_put routines.
The function must return the length in bytes of the UDP reply, or 0 if nothing to
transmit. If you don't need to reply to the UDP requests, just define this function
with a return(0) as single statement.
Description
Parameters:
-
remoteHost: client's IP address.
remotePort: client's port.
destPort: port to which the request is sent.
reqLength: UDP request data field length.
Note: The function source code is provided with appropriate example projects.
The code should be adjusted by the user to achieve desired reply.
Requires
Ethernet module has to be initialized. See Ethernet_Init.
Example
This function is internally called by the library and should not be called by the
user's code.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
269
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Ethernet_getIpAddress
Prototype
function Ethernet_getIpAddress() : word;
Returns
Ponter to the global variable holding IP address.
This routine should be used when DHCP server is present on the network to
fetch assigned IP address.
Description
Note: User should always copy the IP address from the RAM location returned
by this routine into it's own IP address buffer. These locations should not be
altered by the user in any case!
Requires
Ethernet module has to be initialized. See Ethernet_Init.
Example
var
ipAddr : array[4] of byte; // user IP address buffer
...
memcpy(ipAddr, Ethernet_getIpAddress(), 4); // fetch IP address
Ethernet_getGwIpAddress
Prototype
function Ethernet_getGwIpAddress() : word;
Returns
Ponter to the global variable holding gateway IP address.
This routine should be used when DHCP server is present on the network to
fetch assigned gateway IP address.
Description
270
Note: User should always copy the IP address from the RAM location returned
by this routine into it's own gateway IP address buffer. These locations should
not be altered by the user in any case!
Requires
Ethernet module has to be initialized. See Ethernet_Init.
Example
var
gwIpAddr : array[4] of byte; // user gateway IP address buffer
...
memcpy(gwIpAddr, Ethernet_getGwIpAddress(), 4); // fetch gateway IP address
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Ethernet_getDnsIpAddress
Prototype
function Ethernet_getDnsIpAddress() : word;
Returns
Ponter to the global variable holding DNS IP address.
This routine should be used when DHCP server is present on the network to
fetch assigned DNS IP address.
Description
Note: User should always copy the IP address from the RAM location returned
by this routine into it's own DNS IP address buffer. These locations should not
be altered by the user in any case!
Requires
Ethernet module has to be initialized. See Ethernet_Init.
Example
var
dnsIpAddr : array[4] of byte; // user DNS IP address buffer
...
memcpy(dnsIpAddr, Ethernet_getDnsIpAddress(), 4); // fetch DNS
server address
Ethernet_getIpMask
Prototype
function Ethernet_getIpMask() : word;
Returns
Ponter to the global variable holding IP subnet mask.
This routine should be used when DHCP server is present on the network to
fetch assigned IP subnet mask.
Description
Note: User should always copy the IP address from the RAM location returned
by this routine into it's own IP subnet mask buffer. These locations should not
be altered by the user in any case!
Requires
Ethernet module has to be initialized. See Ethernet_Init.
Example
var
IpMask : array[4] of byte; // user IP subnet mask buffer
...
memcpy(IpMask, Ethernet_getIpMask(), 4); // fetch IP subnet
mask
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
271
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Ethernet_confNetwork
Prototype
procedure Ethernet_confNetwork(var ipMask, gwIpAddr, dnsIpAddr :
array[4] of byte);
Returns
Nothing.
Configures network parameters (IP subnet mask, gateway IP address, DNS IP
address) when DHCP is not used.
Parameters:
Description - ipMask: IP subnet mask.
- gwIpAddr gateway IP address.
- dnsIpAddr: DNS IP address.
Note: The above mentioned network parameters should be set by this routine
only if DHCP module is not used. Otherwise DHCP will override these settings.
Requires
Ethernet module has to be initialized. See Ethernet_Init.
var
ipMask
: array[4] of byte;
255.255.255.0)
gwIpAddr : array[4] of byte;
dnsIpAddr : array[4] of byte;
...
gwIpAddr[0] := 192;
gwIpAddr[1] := 168;
gwIpAddr[2] := 20;
gwIpAddr[3] := 6;
Example
dnsIpAddr[0]
dnsIpAddr[1]
dnsIpAddr[2]
dnsIpAddr[3]
:=
:=
:=
:=
// network mask (for example :
// gateway (router) IP address
// DNS server IP address
192;
168;
20;
100;
ipMask[0]
:= 255;
ipMask[1]
:= 255;
ipMask[2]
:= 255;
ipMask[3]
:= 0;
...
Ethernet_confNetwork(ipMask, gwIpAddr, dnsIpAddr); // set network configuration parameters
272
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Ethernet_arpResolve
Prototype
function Ethernet_arpResolve(var ip : array[4] of byte; tmax :
byte) : word;
Returns
- MAC address behind the IP address - the requested IP address was resolved.
- 0 - otherwise.
This is ARP module routine. It sends an ARP request for given IP address and
waits for ARP reply. If the requested IP address was resolved, an ARP cash
entry is used for storing the configuration. ARP cash can store up to 3 entries.
For ARP cash structure refer to "eth_j60LibDef.h" header file in the compiler's Uses/P18 folder.
Description Parameters:
- ip: IP address to be resolved.
- tmax: time in seconds to wait for an reply.
Note: The Ethernet services are not stopped while this routine waits for ARP
reply. The incoming packets will be processed normaly during this time.
Requires
Ethernet module has to be initialized. See Ethernet_Init.
Example
var
IpAddr : array[4] of byte; // IP address
...
IpAddr[0] := 192;
IpAddr[0] := 168;
IpAddr[0] := 1;
IpAddr[0] := 1;
...
Ethernet_arpResolve(IpAddr, 5); // get MAC address behind the
above IP address, wait 5 secs for the response
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
273
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Ethernet_sendUDP
Prototype
function Ethernet_sendUDP(var destIP : array[4] of byte;
sourcePort, destPort : word; pkt : ^byte; pktLen : word) : byte;
Returns
1 - UDP packet was sent successfully.
0 - otherwise.
This is UDP module routine. It sends an UDP packet on the network.
Parameters:
Description -
274
destIP: remote host IP address.
sourcePort: local UDP source port number.
destPort: destination UDP port number.
pkt: packet to transmit.
pktLen: length in bytes of packet to transmit.
Requires
Ethernet module has to be initialized. See Ethernet_Init.
Example
var
IpAddr : array[4] of byte; // remote IP address
...
IpAddr[0] := 192;
IpAddr[0] := 168;
IpAddr[0] := 1;
IpAddr[0] := 1;
...
Ethernet_sendUDP(IpAddr, 10001, 10001, 'Hello', 5); // send
Hello message to the above IP address, from UDP port 10001 to
UDP port 10001
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Ethernet_dnsResolve
Prototype
function Ethernet_dnsResolve(var host : array[4] of byte; tmax :
byte) : word;
Returns
- pointer to the location holding the IP address - the requested host name was
resolved.
- 0 - otherwise.
This is DNS module routine. It sends an DNS request for given host name and
waits for DNS reply. If the requested host name was resolved, it's IP address is
stored in library global variable and a pointer containing this address is returned
by the routine. UDP port 53 is used as DNS port.
Parameters:
Description
- host: host name to be resolved.
- tmax: time in seconds to wait for an reply.
Note: The Ethernet services are not stopped while this routine waits for DNS
reply. The incoming packets will be processed normaly during this time.
Note: User should always copy the IP address from the RAM location returned
by this routine into it's own resolved host IP address buffer. These locations
should not be altered by the user in any case!
Requires
Ethernet module has to be initialized. See Ethernet_Init.
Example
var
remoteHostIpAddr : array[4] of byte; // user host IP address
buffer
...
// SNTP server:
// Zurich, Switzerland: Integrated Systems Lab, Swiss Fed.
Inst. of Technology
// 129.132.2.21: swisstime.ethz.ch
// Service Area: Switzerland and Europe
memcpy(remoteHostIpAddr,
Ethernet_dnsResolve('swisstime.ethz.ch', 5), 4);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
275
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Ethernet_initDHCP
Prototype
function Ethernet_initDHCP(tmax : byte) : byte;
Returns
- 1 - network parameters were obtained successfully.
- 0 - otherwise.
This is DHCP module routine. It sends an DHCP request for network parameters (IP, gateway, DNS addresses and IP subnet mask) and waits for DHCP
reply. If the requested parameters were obtained successfully, their values are
stored into the library global variables.
These parameters can be fetched by using appropriate library IP get routines:
-
Description
Ethernet_getIpAddress - fetch IP address.
Ethernet_getGwIpAddress - fetch gateway IP address.
Ethernet_getDnsIpAddress - fetch DNS IP address.
Ethernet_getIpMask - fetch IP subnet mask.
UDP port 68 is used as DHCP client port and UDP port 67 is used as DHCP
server port.
Parameters:
- tmax: time in seconds to wait for an reply.
Note: The Ethernet services are not stopped while this routine waits for DNS
reply. The incoming packets will be processed normaly during this time.
Note: When DHCP module is used, global library variable
Ethernet_userTimerSec is used to keep track of time. It is user responsibility
to increment this variable each second in it's code.
276
Requires
Ethernet module has to be initialized. See Ethernet_Init.
Example
...
Ethernet_initDHCP(5); // get network configuration from DHCP
server, wait 5 sec for the response
...
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Ethernet_doDHCPLeaseTime
Prototype
function Ethernet_doDHCPLeaseTime() : byte;
Returns
- 0 - lease time has not expired yet.
- 1 - lease time has expired, it's time to renew it.
This is DHCP module routine. It takes care of IP address lease time by decreDescription menting the global lease time library counter. When this time expires, it's time to
contact DHCP server and renew the lease.
Requires
Ethernet module has to be initialized. See Ethernet_Init.
Example
while true do
begin
...
if(Ethernet_doDHCPLeaseTime() <> 0) then
begin
... // it's time to renew the IP address lease
end;
end;
Ethernet_renewDHCP
Prototype
function Ethernet_renewDHCP(tmax : byte) : byte;
Returns
- 1 - upon success (lease time was renewed).
- 0 - otherwise (renewal request timed out).
This is DHCP module routine. It sends IP address lease time renewal request to
DHCP server.
Description
Parameters:
- tmax: time in seconds to wait for an reply.
Requires
Ethernet module has to be initialized. See Ethernet_Init.
Example
while true do
begin
...
if(Ethernet_doDHCPLeaseTime() <> 0) then
begin
Ethernet_renewDHCP(5); // it's time to renew the IP
address lease, with 5 secs for a reply
end;
...
end;
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
277
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Example
This code shows how to use the PIC18FxxJ60 Ethernet library :
- the board will reply to ARP & ICMP echo requests
- the board will reply to UDP requests on any port :
returns the request in upper char with a header made of remote host IP &
port number
- the board will reply to HTTP requests on port 80, GET method with pathnames :
/ will return the HTML main page
/s will return board status as text string
/t0 ... /t7 will toggle RD0 to RD7 bit and return HTML main page
all other requests return also HTML main page.
program enc_ethernet;
{***********************************
* RAM variables
*}
var myMacAddr
: array[6] of byte ; // my MAC address
myIpAddr
: array[4] of byte ; // my IP address
gwIpAddr
: array[4] of byte ; // gateway (router) IP address
ipMask
: array[4] of byte ; // network mask (for example
: 255.255.255.0)
dnsIpAddr
: array[4] of byte ; // DNS server IP address
{************************************************************
* ROM constant strings
*}
const httpHeader : string[30] = 'HTTP/1.1 200 OK'+#10+'Content-type:
' ; // HTTP header
const httpMimeTypeHTML : string[11]
= 'text/html'+#10+#10 ;
// HTML MIME type
const httpMimeTypeScript : string[12] = 'text/plain'+#10+#10 ;
// TEXT MIME type
const httpMethod : string[5] = 'GET /';
{*
* web page, splited into 2 parts :
* when coming short of ROM, fragmented data is handled more efficiently by linker
*
* this HTML page calls the boards to get its status, and builds
itself with javascript
*}
278
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
const indexPage : string[759] =
'<meta http-equiv="refresh"
content="3;url=http://192.168.20.60">' +
'<HTML><HEAD></HEAD><BODY>'+
'<h1>PIC18FxxJ60 Mini Web Server</h1>'+
'<a href=/>Reload</a>'+
'<script src=/s></script>'+
'<table><tr><td valign=top><table border=1
style="font-size:20px ;font-family: terminal ;">'+
'<tr><th colspan=2>ADC</th></tr>'+
'<tr><td>AN2</td><td><script>document.write(AN2)</script></td></tr>'
+
'<tr><td>AN3</td><td><script>document.write(AN3)</script></td></tr>'
+
'</table></td><td><table border=1 style="fontsize:20px ;font-family: terminal ;">'+
'<tr><th colspan=2>PORTB</th></tr>'+
'<script>'+
'var str,i;'+
'str="";'+
'for(i=0;i<8;i++)'+
'{str+="<tr><td bgcolor=pink>BUTTON #"+i+"</td>";'+
'if(PORTB&(1<<i)){str+="<td bgcolor=red>ON";}'+
'else {str+="<td bgcolor=#cccccc>OFF";}'+
'str+="</td></tr>";}'+
'document.write(str) ;'+
'</script>';
const indexPage2 : string[466] =
'</table></td><td>'+
'<table border=1 style="font-size:20px ;fontfamily: terminal ;">'+
'<tr><th colspan=3>PORTD</th></tr>'+
'<script>'+
'var str,i;'+
'str="";'+
'for(i=0;i<3;i++)'+
'{str+="<tr><td bgcolor=yellow>LED #"+i+"</td>";'+
'if(PORTD&(1<<i)){str+="<td bgcolor=red>ON";}'+
'else {str+="<td bgcolor=#cccccc>OFF";}'+
'str+="</td><td><a
href=/t"+i+">Toggle</a></td></tr>";}'+
'document.write(str) ;'+
'</script>'+
'</table></td></tr></table>'+
'This is HTTP request
#<script>document.write(REQ)</script></BODY></HTML>';
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
279
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
var
getRequest : array[15] of byte; // HTTP request buffer
dyna
: array[30] of byte; // buffer for dynamic response
httpCounter : word ;
// counter of HTTP requests
{*******************************************
* user defined functions
*}
{*
* this function is called by the library
* the user accesses to the HTTP request by successive calls to
Ethernet_getByte()
* the user puts data in the transmit buffer by successive calls to
Ethernet_putByte()
* the function must return the length in bytes of the HTTP reply,
or 0 if nothing to transmit
*
* if you don't need to reply to HTTP requests,
* just define this function with a return(0) as single statement
*
*}
function Ethernet_UserTCP(var remoteHost : array[4] of byte;
remotePort, localPort, reqLength
: word) : word;
var i : word ;
// my reply length
bitMask : byte ; // for bit mask
tmp: string[11]; // to copy const array to ram for memcmp
begin
result := 0;
if(localPort <> 80) then // I listen only to web request on port 80
begin
result := 0;
exit;
end;
// get 10 first bytes only of the request, the rest does not matter here
for i := 0 to 9 do
getRequest[i] := Ethernet_getByte() ;
getRequest[i] := 0 ;
// copy httpMethod to ram for use in memcmp routine
for i := 0 to 4 do
tmp[i] := httpMethod[i];
if(memcmp(@getRequest, @tmp, 5) <> 0) then
is supported here
begin
result := 0 ;
exit;
end;
280
// only GET method
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Inc(httpCounter) ;
// one more request done
if(getRequest[5] = 's') then
// if request path
name starts with s, store dynamic data in transmit buffer
begin
// the text string replied by this request can be interpreted as javascript statements
// by browsers
result := Ethernet_putConstString(@httpHeader) ;// HTTP header
result
:=
result
+
Ethernet_putConstString(@httpMimeTypeScript) ; // with text MIME type
// add AN2 value to reply
WordToStr(ADC_Read(2), dyna) ;
tmp := 'var AN2=';
result := result + Ethernet_putString(@tmp) ;
result := result + Ethernet_putString(@dyna) ;
tmp := ';';
result := result + Ethernet_putString(@tmp) ;
// add AN3 value to reply
WordToStr(ADC_Read(3), dyna) ;
tmp := 'var AN3=';
result := result + Ethernet_putString(@tmp) ;
result := result + Ethernet_putString(@dyna) ;
tmp := ';';
result := result + Ethernet_putString(@tmp) ;
// add PORTB value (buttons) to reply
tmp := 'var PORTB= ';
result := result + Ethernet_putString(@tmp) ;
WordToStr(PORTB, dyna) ;
result := result + Ethernet_putString(@dyna) ;
tmp := ';';
result := result + Ethernet_putString(@tmp) ;
// add PORTD value (LEDs) to reply
tmp := 'var PORTD= ';
result := result + Ethernet_putString(@tmp) ;
WordToStr(PORTD, dyna) ;
result := result + Ethernet_putString(@dyna) ;
tmp := ';';
result := result + Ethernet_putString(@tmp) ;
// add HTTP requests counter to reply
WordToStr(httpCounter, dyna) ;
tmp := 'var REQ=
';
result := result + Ethernet_putString(@tmp) ;
result := result + Ethernet_putString(@dyna) ;
tmp := ';';
result := result + Ethernet_putString(@tmp) ;
end
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
281
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
else
if(getRequest[5] = 't') then
// if request path
name starts with t, toggle PORTD (LED) bit number that comes after
begin
bitMask := 0;
if(isdigit(getRequest[6]) <> 0) then
// if 0
<= bit number <= 9, bits 8 & 9 does not exist but does not matter
begin
bitMask := getRequest[6] - '0' ;
// convert ASCII to integer
bitMask := 1 shl bitMask ;
// create bit mask
PORTD
:= PORTD xor bitMask ;
// toggle PORTD with xor operator
end;
end;
if(result = 0) then // what do to by default
begin
result := Ethernet_putConstString(@httpHeader) ;
// HTTP header
result := result + Ethernet_putConstString(@httpMimeTypeHTML)
; // with HTML MIME type
result := result + Ethernet_putConstString(@indexPage) ;
// HTML page first part
result := result + Ethernet_putConstString(@indexPage2) ;
// HTML page second part
end;
// return to the library with the number of bytes to transmit
end;
{*
* this function is called by the library
* the user accesses to the UDP request by successive calls to
Ethernet_getByte()
* the user puts data in the transmit buffer by successive calls to
Ethernet_putByte()
* the function must return the length in bytes of the UDP reply, or
0 if nothing to transmit
*
* if you don't need to reply to UDP requests,
* just define this function with a return(0) as single statement
*
*}
function Ethernet_UserUDP(var remoteHost : array[4] of byte;
remotePort, destPort, reqLength
: word) : word;
var tmp : string[5];
282
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
begin
result := 0;
// reply is made of the remote host IP address in human readable
format
byteToStr(remoteHost[0], dyna) ;
// first IP address
byte
dyna[3] := '.' ;
byteToStr(remoteHost[1], tmp) ;
// second
dyna[4] := tmp[0];
dyna[5] := tmp[1];
dyna[6] := tmp[2];
dyna[7] := '.' ;
byteToStr(remoteHost[2], tmp) ;
// second
dyna[8] := tmp[0];
dyna[9] := tmp[1];
dyna[10] := tmp[2];
dyna[11] := '.' ;
byteToStr(remoteHost[3], tmp) ;
// second
dyna[12] := tmp[0];
dyna[13] := tmp[1];
dyna[14] := tmp[2];
dyna[15] := ':' ;
// add separator
// then remote host port number
WordToStr(remotePort, tmp) ;
dyna[16] := tmp[0];
dyna[17] := tmp[1];
dyna[18] := tmp[2];
dyna[19] := tmp[3];
dyna[20] := tmp[4];
dyna[21] := '[' ;
WordToStr(destPort, tmp) ;
dyna[22] := tmp[0];
dyna[23] := tmp[1];
dyna[24] := tmp[2];
dyna[25] := tmp[3];
dyna[26] := tmp[4];
dyna[27] := ']' ;
dyna[28] := 0 ;
// the total length of the request is the length of the dynamic
string plus the text of the request
result := 28 + reqLength ;
// puts the dynamic string into the transmit buffer
Ethernet_putBytes(@dyna, 28) ;
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
283
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
// then puts the request string converted into upper char into the
transmit buffer
while(reqLength <> 0) do
begin
Ethernet_putByte(Ethernet_getByte()) ;
reqLength := reqLength - 1;
end;
// back to the library with the length of the UDP reply
end;
begin
ADCON1 := 0x0B ;
and AN3
CMCON := 0x07 ;
// ADC convertors will be used with AN2
// turn off comparators
PORTA
TRISA
:= 0 ;
:= 0x0C ;
PORTB
TRISB
:= 0 ;
:= 0xff ;
// set PORTB as input for buttons
PORTD
TRISD
:= 0 ;
:= 0 ;
// set PORTD as output
// RA2:RA3 - analog inputs
// RA1:RA0 - ethernet LEDA:LEDB
httpCounter := 0;
// set mac address
myMacAddr[0] := 0x00;
myMacAddr[1] := 0x14;
myMacAddr[2] := 0xA5;
myMacAddr[3] := 0x76;
myMacAddr[4] := 0x19;
myMacAddr[5] := 0x3F;
// set IP address
myIpAddr[0] := 192;
myIpAddr[1] := 168;
myIpAddr[2] := 20;
myIpAddr[3] := 60;
// set gateway address
gwIpAddr[0] := 192;
gwIpAddr[1] := 168;
gwIpAddr[2] := 20;
gwIpAddr[3] := 6;
284
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
// set dns address
dnsIpAddr[0] := 192;
dnsIpAddr[1] := 168;
dnsIpAddr[2] := 20;
dnsIpAddr[3] := 1;
// set subnet mask
ipMask[0]
:= 255;
ipMask[1]
:= 255;
ipMask[2]
:= 255;
ipMask[3]
:= 0;
{*
* starts ENC28J60 with :
* reset bit on PORTC.B0
* CS bit on PORTC.B1
* my MAC & IP address
* full duplex
*}
Ethernet_Init(myMacAddr, myIpAddr, _Ethernet_FULLDUPLEX) ; // init
ethernet module
Ethernet_setUserHandlers(@Ethernet_UserTCP, @Ethernet_UserUDP); //
set user handlers
// dhcp will not be used here, so use preconfigured addresses
Ethernet_confNetwork(ipMask, gwIpAddr, dnsIpAddr) ;
while true do
begin
Ethernet_doPacket() ;
// do forever
// process incoming Ethernet packets
{*
* add your stuff here if needed
* Ethernet_doPacket() must be called as often as possible
* otherwise packets could be lost
*}
end;
end.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
285
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
FLASH MEMORY LIBRARY
This library provides routines for accessing microcontroller Flash memory. Note that
prototypes differ for PIC16 and PIC18 families.
Note: Due to the P16/P18 family flash specifics, flash library is MCU dependent.
Since the P18 family differ significantlly in number of bytes that can be erased
and/or written to specific MCUs, the appropirate suffix is added to the names of
functions in order to make it easier to use them. Flash memory operations are MCU
dependent :
1. Read operation supported. For this group of MCU's only read function is
implemented.
2. Read and Write operations supported (write is executed as erase-and-write). For
this group of MCU's read and write functions are implemented. Note that write
operation which is executed as erase-and-write, may write less bytes than it erases.
3. Read, Write and Erase operations supported. For this group of MCU's read, write
and erase functions are implemented. Further more, flash memory block has to
be erased prior to writting (write operation is not executed as erase-and-write).
Please refer to MCU datasheet before using flash library.
Library Routines
-
286
FLASH_Read
FLASH_Read_N_Bytes
FLASH_Write
FLASH_Write_8
FLASH_Write_16
FLASH_Write_32
FLASH_Write_64
FLASH_Erase
FLASH_Erase_64
FLASH_Erase_1024
FLASH_Erase_Write
FLASH_Erase_Write_64
FLASH_Erase_Write_1024
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
FLASH_Read
// for PIC16
function FLASH_Read(Address: word): word;
Prototype
// for PIC18
function FLASH_Read(address : dword) : byte;
Returns
Returns data byte from Flash memory.
Description Reads data from the specified address in Flash memory.
Requires
Nothing.
Example
// for PIC18
var tmp : byte;
...
begin
...
tmp := FLASH_Read(0x0D00);
...
end.
FLASH_Read_N_Bytes
Prototype
// for PIC18
procedure FLASH_Read_N_Bytes(address : longint; var data : byte;
N : word);
Returns
Nothing.
Description
Reads N data from the specified address in Flash memory to varibale pointed
by data
Requires
Nothing.
Example
FLASH_Read_N(0x0D00, data_buffer, sizeof(data_buffer));
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
287
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
FLASH_Write
// for PIC16
procedure FLASH_Write(Address : word; var Data : array[4] of word);
// for PIC18
procedure FLASH_Write_8(address : dword; var data: array[8] of
byte);
Prototype
procedure FLASH_Write_16(address : dword; var data: array[16] of
byte);
procedure FLASH_Write_32(address : dword; var data: array[32] of
byte);
procedure FLASH_Write_64(address : dword; var data: array[64] of
byte);
Returns
Nothing.
Writes block of data to Flash memory. Block size is MCU dependent.
P16: This function may erase memory segment before writing block of data to it
(MCU dependent). Furthermore, memory segment which will be erased may be
greater than the size of the data block that will be written (MCU dependent).
Description Therefore it is recommended to write as many bytes as you erase.
FLASH_Write writes 4 flash memory locations in a row, so it needs to be called
as many times as it is necessary to meet the size of the data block that will be
written.
P18: This function does not perform erase prior to write.
Requires
Flash memory that will be written may have to be erased before this function is
called (MCU dependent). Refer to MCU datasheet for details.
Write consecutive values in 64 consecutive locations, starting from 0x0D00:
Example
288
var toWrite : array[64] of byte;
...
begin
...
// initialize array:
for i := 0 to 63 do
toWrite[i] := i;
...
// write contents of the array to the address 0x0D00:
FLASH_Write_64(0x0D00, toWrite);
...
end.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
FLASH_Erase
// for PIC16
procedure FLASH_Erase(address : word);
Prototype
// for PIC18
procedure FLASH_Erase_64(address : dword);
procedure FLASH_Erase_1024(address : dword);
Returns
Nothing.
Erases memory block starting from a given address. For P16 familly is impleDescription mented only for those MCU's whose flash memory does not support erase-andwrite operations (refer to datasheet for details).
Requires
Nothing.
Erase 64 byte memory memory block, starting from address $0D00:
Example
FLASH_Erase_64($0D00);
FLASH_Erase_Write
// for PIC18
Prototype
procedure FLASH_Erase_Write_64(address : dword; var data :
array[64] of byte);
procedure FLASH_Erase_Write_1024(address : dword; var data :
array[1024] of byte);
Returns
None.
Description Erase then write memory block starting from a given address.
Requires
None.
Example
var toWrite : array[64] of byte;
...
begin
...
// initialize array:
for i := 0 to 63 do
toWrite[i] := i;
...
// erase block of memory at address 0x0D00 then write contents of
the array to the address 0x0D00:
FLASH_Erase_Write_64(0x0D00, toWrite);
...
end.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
289
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Example
This is a simple demonstration how to use to PIC16 internal flash memory to store
data. The data is being written starting from the given location; then, the same locations are read and the data is displayed on PORTB and PORTC.
var counter : byte;
addr, data_ : word;
dataAR: array[5] of array[4] of word;
begin
ANSEL := 0;
ital I/O
ANSELH := 0;
PORTB := 0;
TRISB := 0;
PORTC := 0;
TRISC := 0;
Delay_ms(500);
dataAR[0][0]:=
dataAR[0][1]:=
dataAR[0][2]:=
dataAR[0][3]:=
dataAR[1][0]:=
dataAR[1][1]:=
dataAR[1][2]:=
dataAR[1][3]:=
dataAR[2][0]:=
dataAR[2][1]:=
dataAR[2][2]:=
dataAR[2][3]:=
dataAR[3][0]:=
dataAR[3][1]:=
dataAR[3][2]:=
dataAR[3][3]:=
dataAR[4][0]:=
dataAR[4][1]:=
dataAR[4][2]:=
dataAR[4][3]:=
// configure AN pins as dig-
//
//
//
//
initial PORTB value
set PORTB as output
initial PORTC value
set PORTC as output
$FFAA+0;
$FFAA+1;
$FFAA+2;
$FFAA+3;
$FFAA+4;
$FFAA+5;
$FFAA+6;
$FFAA+7;
$FFAA+8;
$FFAA+9;
$FFAA+10;
$FFAA+11;
$FFAA+12;
$FFAA+13;
$FFAA+14;
$FFAA+15;
$FFAA+16;
$FFAA+17;
$FFAA+18;
$FFAA+19;
addr := 0x0430;
// starting Flash address,
valid for P16F887
for counter := 0 to 4 do
begin
// write some data to Flash
Delay_ms(100);
Flash_Write(addr+counter*4, dataAR[counter]);
end;
290
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Delay_ms(500);
addr := 0x0430;
for counter := 0 to 19 do
begin
data_ := Flash_Read(addr);
wide, so
Inc(addr);
Delay_us(10);
be '00'
PORTB := data_;
LS Byte
PORTC := word(data_ shr 8);
Delay_ms(500);
end;
end.
// P16's FLASH is 14-bit
//
two MSB's will always
// display data on PORTB
// and PORTC MS Byte
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
291
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
GRAPHIC LCD LIBRARY
The mikroPascal PRO for PIC provides a library for operating Graphic Lcd 128x64
(with commonly used Samsung KS108/KS107 controller).
For creating a custom set of Glcd images use Glcd Bitmap Editor Tool.
External dependencies of Graphic Lcd Library
The following variables
must be defined in all
projects using Graphic
Lcd Library:
var GLCD_DataPort :
byte; sfr; external;
var GLCD_CS1 : sbit;
sfr; external;
var GLCD_CS2 : sbit;
sfr; external;
var GLCD_RS : sbit;
sfr; external;
var GLCD_RW : sbit;
sfr; external;
var GLCD_EN : sbit;
sfr; external;
var GLCD_RST : sbit;
sfr; external;
292
Description:
Example :
Reset line.
var GLCD_DataPort :
byte at PORTD;
var GLCD_CS1 : sbit
at RB0_bit;
var GLCD_CS2 : sbit
at RB1_bit;
var GLCD_RS : sbit at
RB2_bit;
var GLCD_RW : sbit at
RB3_bit;
var GLCD_EN : sbit at
RB4_bit;
var GLCD_RST : sbit
at RB5_bit;
var
GLCD_CS1_Direction :
sbit; sfr; external;
Direction of the Chip
Select 1 pin.
var
GLCD_CS1_Direction :
sbit at TRISB0_bit;
var
GLCD_CS2_Direction :
sbit; sfr; external;
Direction of the Chip
Select 2 pin.
var
GLCD_CS2_Direction :
sbit at TRISB1_bit;
Glcd Data Port.
Chip Select 1 line.
Chip Select 2 line.
Register select line.
Read/Write line.
Enable line.
var GLCD_RS_Direction Direction of the Register
: sbit; sfr; external; select pin.
var GLCD_RS_Direction
: sbit at TRISB2_bit;
var GLCD_RW_Direction Direction of the
: sbit; sfr; external; Read/Write pin.
var GLCD_RW_Direction
: sbit at TRISB3_bit;
var GLCD_EN_Direction Direction of the Enable
: sbit; sfr; external; pin.
var GLCD_EN_Direction
: sbit at TRISB4_bit;
var
GLCD_RST_Direction :
sbit; sfr; external;
var
Direction of the Reset pin. GLCD_RST_Direction :
sbit at TRISB5_bit;
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Routines
Basic routines:
-
Glcd_Init
Glcd_Set_Side
Glcd_Set_X
Glcd_Set_Page
Glcd_Read_Data
Glcd_Write_Data
Advanced routines:
-
Glcd_Fill
Glcd_Dot
Glcd_Line
Glcd_V_Line
Glcd_H_Line
Glcd_Rectangle
Glcd_Box
Glcd_Circle
Glcd_Set_Font
Glcd_Write_Char
Glcd_Write_Text
Glcd_Image
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
293
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Glcd_Init
Prototype
procedure Glcd_Init();
Returns
Nothing.
Description
Initializes the Glcd module. Each of the control lines is both port and pin configurable, while data lines must be on a single port (pins <0:7>).
Global variables :
Requires
-
GLCD_CS1 : Chip select 1 signal pin
GLCD_CS2 : Chip select 2 signal pin
GLCD_RS : Register select signal pin
GLCD_RW : Read/Write Signal pin
GLCD_EN : Enable signal pin
GLCD_RST : Reset signal pin
GLCD_DataPort : Data port
GLCD_CS1_Direction : Direction of the Chip select 1 pin
GLCD_CS2_Direction : Direction of the Chip select 2 pin
GLCD_RS_Direction : Direction of the Register select signal pin
GLCD_RW_Direction : Direction of the Read/Write signal pin
GLCD_EN_Direction : Direction of the Enable signal pin
GLCD_RST_Direction : Direction of the Reset signal pin
must be defined before using this function.
// Glcd module connections
var GLCD_DataPort : byte at PORTD;
var GLCD_CS1
GLCD_CS2
GLCD_RS
GLCD_RW
GLCD_EN
GLCD_RST
Example
:
:
:
:
:
:
sbit
sbit
sbit
sbit
sbit
sbit
at
at
at
at
at
at
RB0_bit;
RB1_bit;
RB2_bit;
RB3_bit;
RB4_bit;
RB5_bit;
var GLCD_CS1_Direction : sbit at
GLCD_CS2_Direction : sbit at
GLCD_RS_Direction : sbit at
GLCD_RW_Direction : sbit at
GLCD_EN_Direction : sbit at
GLCD_RST_Direction : sbit at
// End Glcd module connections
TRISB0_bit;
TRISB1_bit;
TRISB2_bit;
TRISB3_bit;
TRISB4_bit;
TRISB5_bit;
...
ANSEL = 0;
ANSELH = 0;
Glcd_Init();
294
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Glcd_Set_Side
Prototype
procedure Glcd_Set_Side(x_pos: byte);
Returns
Nothing.
Selects Glcd side. Refer to the Glcd datasheet for detailed explaination.
Parameters :
- x_pos: position on x-axis. Valid values: 0..127
Description
The parameter x_pos specifies the Glcd side: values from 0 to 63 specify the
left side, values from 64 to 127 specify the right side.
Note: For side, x axis and page layout explanation see schematic at the bottom
of this page.
Requires
Glcd needs to be initialized, see Glcd_Init routine.
The following two lines are equivalent, and both of them select the left side of Glcd:
Example
Glcd_Select_Side(0);
Glcd_Select_Side(10);
Glcd_Set_X
Prototype
procedure Glcd_Set_X(x_pos: byte);
Returns
Nothing.
Sets x-axis position to x_pos dots from the left border of Glcd within the selected side.
Parameters :
Description
- x_pos: position on x-axis. Valid values: 0..63
Note: For side, x axis and page layout explanation see schematic at the bottom
of this page.
Requires
Glcd needs to be initialized, see Glcd_Init routine.
Example
Glcd_Set_X(25);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
295
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Glcd_Set_Page
Prototype
procedure Glcd_Set_Page(page: byte);
Returns
Nothing.
Selects page of the Glcd.
Parameters :
Description
- page: page number. Valid values: 0..7
Note: For side, x axis and page layout explanation see schematic at the bottom
of this page.
Requires
Glcd needs to be initialized, see Glcd_Init routine.
Example
Glcd_Set_Page(5);
Glcd_Read_Data
Prototype
function Glcd_Read_Data(): byte;
Returns
One byte from Glcd memory.
Description
Reads data from from the current location of Glcd memory and moves to the
next location.
Glcd needs to be initialized, see Glcd_Init routine.
Requires
Example
296
Glcd side, x-axis position and page should be set first. See functions
Glcd_Set_Side, Glcd_Set_X, and Glcd_Set_Page.
var data: byte;
...
data := Glcd_Read_Data();
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Glcd_Write_Data
Prototype
procedure Glcd_Write_Data(ddata: byte);
Returns
Nothing.
Writes one byte to the current location in Glcd memory and moves to the next
location.
Description
Parameters :
- ddata: data to be written
Glcd needs to be initialized, see Glcd_Init routine.
Requires
Example
Glcd side, x-axis position and page should be set first. See functions
Glcd_Set_Side, Glcd_Set_X, and Glcd_Set_Page.
var data: byte;
...
Glcd_Write_Data(data);
Glcd_Fill
Prototype
procedure Glcd_Fill(pattern: byte);
Returns
Nothing.
Fills Glcd memory with the byte pattern.
Parameters :
Description - pattern: byte to fill Glcd memory with
To clear the Glcd screen, use Glcd_Fill(0).
To fill the screen completely, use Glcd_Fill(0xFF).
Requires
Glcd needs to be initialized, see Glcd_Init routine.
Example
' Clear screen
Glcd_Fill(0);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
297
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Glcd_Dot
Prototype
procedure Glcd_Dot(x_pos: byte; y_pos: byte; color: byte);
Returns
Nothing.
Draws a dot on Glcd at coordinates (x_pos, y_pos).
Parameters :
- x_pos: x position. Valid values: 0..127
- y_pos: y position. Valid values: 0..63
Description
- color: color parameter. Valid values: 0..2
The parameter color determines a dot state: 0 clears dot, 1 puts a dot, and 2
inverts dot state.
Note: For x and y axis layout explanation see schematic at the bottom of this page.
Requires
Glcd needs to be initialized, see Glcd_Init routine.
Example
' Invert the dot in the upper left corner
Glcd_Dot(0, 0, 2);
Glcd_Line
Prototype
procedure Glcd_Line(x_start: integer; y_start: integer; x_end:
integer; y_end: integer; color: byte);
Returns
Nothing.
Draws a line on Glcd.
Parameters :
Description
-
x_start: x coordinate of the line start. Valid values: 0..127
y_start: y coordinate of the line start. Valid values: 0..63
x_end: x coordinate of the line end. Valid values: 0..127
y_end: y coordinate of the line end. Valid values: 0..63
color: color parameter. Valid values: 0..2
The parameter color determines the line color: 0 white, 1 black, and 2 inverts
each dot.
298
Requires
Glcd needs to be initialized, see Glcd_Init routine.
Example
' Draw a line between dots (0,0) and (20,30)
Glcd_Line(0, 0, 20, 30, 1);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Glcd_V_Line
Prototype
procedure Glcd_V_Line(y_start: byte; y_end: byte; x_pos: byte;
color: byte);
Returns
Nothing.
Draws a vertical line on Glcd.
Parameters :
Description -
y_start: y coordinate of the line start. Valid values: 0..63
y_end: y coordinate of the line end. Valid values: 0..63
x_pos: x coordinate of vertical line. Valid values: 0..127
color: color parameter. Valid values: 0..2
The parameter color determines the line color: 0 white, 1 black, and 2 inverts
each dot.
Requires
Glcd needs to be initialized, see Glcd_Init routine.
Example
' Draw a vertical line between dots (10,5) and (10,25)
Glcd_V_Line(5, 25, 10, 1);
Glcd_H_Line
Prototype
procedure Glcd_V_Line(x_start: byte; x_end: byte; y_pos: byte;
color: byte);
Returns
Nothing.
Draws a horizontal line on Glcd.
Parameters :
Description -
x_start: x coordinate of the line start. Valid values: 0..127
x_end: x coordinate of the line end. Valid values: 0..127
y_pos: y coordinate of horizontal line. Valid values: 0..63
color: color parameter. Valid values: 0..2
The parameter color determines the line color: 0 white, 1 black, and 2 inverts
each dot.
Requires
Glcd needs to be initialized, see Glcd_Init routine.
Example
' Draw a horizontal line between dots (10,20) and (50,20)
Glcd_H_Line(10, 50, 20, 1);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
299
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Glcd_Rectangle
Prototype
procedure Glcd_Rectangle(x_upper_left: byte; y_upper_left: byte;
x_bottom_right: byte; y_bottom_right: byte; color: byte);
Returns
Nothing.
Draws a rectangle on Glcd.
Parameters :
- x_upper_left: x coordinate of the upper left rectangle corner. Valid values: 0..127
- y_upper_left: y coordinate of the upper left rectangle corner. Valid values: 0..63
- x_bottom_right: x coordinate of the lower right rectangle corner. Valid
Description
values: 0..127
- y_bottom_right: y coordinate of the lower right rectangle corner. Valid
values: 0..63
- color: color parameter. Valid values: 0..2
The parameter color determines the color of the rectangle border: 0 white, 1
black, and 2 inverts each dot.
Requires
Glcd needs to be initialized, see Glcd_Init routine.
Example
' Draw a rectangle between dots (5,5) and (40,40)
Glcd_Rectangle(5, 5, 40, 40, 1);
Glcd_Box
Prototype
procedure Glcd_Box(x_upper_left: byte; y_upper_left: byte; x_bottom_right: byte; y_bottom_right: byte; color: byte);
Returns
Nothing.
Draws a box on Glcd.
Parameters :
- x_upper_left: x coordinate of the upper left box corner. Valid values: 0..127
- y_upper_left: y coordinate of the upper left box corner. Valid values: 0..63
Description - x_bottom_right: x coordinate of the lower right box corner. Valid values: 0..127
- y_bottom_right: y coordinate of the lower right box corner. Valid values: 0..63
- color: color parameter. Valid values: 0..2
The parameter color determines the color of the box fill: 0 white, 1 black, and 2
inverts each dot.
300
Requires
Glcd needs to be initialized, see Glcd_Init routine.
Example
' Draw a box between dots (5,15) and (20,40)
Glcd_Box(5, 15, 20, 40, 1);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Glcd_Circle
Prototype
procedure Glcd_Circle(x_center: integer; y_center: integer;
radius: integer; color: byte);
Returns
Nothing.
Draws a circle on Glcd.
Parameters :
Description -
x_center: x coordinate of the circle center. Valid values: 0..127
y_center: y coordinate of the circle center. Valid values: 0..63
radius: radius size
color: color parameter. Valid values: 0..2
The parameter color determines the color of the circle line: 0 white, 1 black,
and 2 inverts each dot.
Requires
Glcd needs to be initialized, see Glcd_Init routine.
Example
' Draw a circle with center in (50,50) and radius=10
Glcd_Circle(50, 50, 10, 1);
Glcd_Set_Font
Prototype
procedure Glcd_Set_Font(const ActiveFont: ^byte; FontWidth: byte;
FontHeight: byte; FontOffs: word);
Returns
Nothing.
Sets font that will be used with Glcd_Write_Char and Glcd_Write_Text routines.
Parameters :
Description -
activeFont: font to be set. Needs to be formatted as an array of byte
aFontWidth: width of the font characters in dots.
aFontHeight: height of the font characters in dots.
aFontOffs: number that represents difference between the mikroPascal PRO
for PIC character set and regular ASCII set (eg. if 'A' is 65 in ASCII character,
and 'A' is 45 in the mikroPascal PRO for PIC character set, aFontOffs is 20).
Demo fonts supplied with the library have an offset of 32, which means that
they start with space.
The user can use fonts given in the file “__Lib_GLCDFonts.mpas” file located in
the Uses folder or create his own fonts.
Requires
Glcd needs to be initialized, see Glcd_Init routine.
Example
' Use the custom 5x7 font "myfont" which starts with space (32):
Glcd_Set_Font(myfont, 5, 7, 32);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
301
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Glcd_Write_Char
Prototype
procedure Glcd_Write_Char(chr: byte; x_pos: byte; page_num: byte;
color: byte);
Returns
Nothing.
Prints character on the Glcd.
Parameters :
- chr: character to be written
- x_pos: character starting position on x-axis. Valid values: 0..(127-FontWidth)
- page_num: the number of the page on which character will be written. Valid
Description
values: 0..7
- color: color parameter. Valid values: 0..2
The parameter color determines the color of the character: 0 white, 1 black, and
2 inverts each dot.
Note: For x axis and page layout explanation see schematic at the bottom of
this page.
302
Requires
Glcd needs to be initialized, see Glcd_Init routine. Use Glcd_Set_Font to specify the font for display; if no font is specified, then default 5x8 font supplied with
the library will be used.
Example
' Write character 'C' on the position 10 inside the page 2:
Glcd_Write_Char('C', 10, 2, 1);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Glcd_Write_Text
Prototype
procedure Glcd_Write_Text(var text: array[20] of char; x_pos:
byte; page_num: byte; color: byte);
Returns
Nothing.
Prints text on Glcd.
Parameters :
- text: text to be written
- x_pos: text starting position on x-axis.
- page_num: the number of the page on which text will be written. Valid values: 0..7
Description
- color: color parameter. Valid values: 0..2
The parameter color determines the color of the text: 0 white, 1 black, and 2
inverts each dot.
Note: For x axis and page layout explanation see schematic at the bottom of
this page.
Requires
Glcd needs to be initialized, see Glcd_Init routine. Use Glcd_Set_Font to specify the font for display; if no font is specified, then default 5x8 font supplied with
the library will be used.
Example
' Write text "Hello world!" on the position 10 inside the page 2:
Glcd_Write_Text("Hello world!", 10, 2, 1);
Glcd_Image
Prototype
procedure Glcd_Image(const image: ^byte);
Returns
Nothing.
Displays bitmap on Glcd.
Parameters :
Description
- image: image to be displayed. Bitmap array must be located in code memory.
Use the mikroPascal PRO for PIC integrated Glcd Bitmap Editor to convert
image to a constant array suitable for displaying on Glcd.
Requires
Glcd needs to be initialized, see Glcd_Init routine.
Example
' Draw image my_image on Glcd
Glcd_Image(my_image);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
303
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Example
The following example demonstrates routines of the Glcd library: initialization,
clear(pattern fill), image displaying, drawing lines, circles, boxes and rectangles, text
displaying and handling.
program GLCD_Test;
uses bitmap;
// Glcd module connections
var GLCD_DataPort : byte at PORTD;
var GLCD_CS1
GLCD_CS2
GLCD_RS
GLCD_RW
GLCD_EN
GLCD_RST
:
:
:
:
:
:
sbit
sbit
sbit
sbit
sbit
sbit
at
at
at
at
at
at
RB0_bit;
RB1_bit;
RB2_bit;
RB3_bit;
RB4_bit;
RB5_bit;
var GLCD_CS1_Direction : sbit at
GLCD_CS2_Direction : sbit at
GLCD_RS_Direction : sbit at
GLCD_RW_Direction : sbit at
GLCD_EN_Direction : sbit at
GLCD_RST_Direction : sbit at
// End Glcd module connections
TRISB0_bit;
TRISB1_bit;
TRISB2_bit;
TRISB3_bit;
TRISB4_bit;
TRISB5_bit;
var counter : byte;
someText : array[18] of char;
procedure Delay2S();
begin
Delay_ms(2000);
end;
// 2 seconds delay function
begin
ANSEL := 0;
ANSELH := 0;
// Configure AN pins as digital I/O
Glcd_Init();
Glcd_Fill(0x00);
while TRUE do
begin
Glcd_Image(@truck_bmp);
Delay2S(); delay2S();
Glcd_Fill(0x00);
304
// Initialize Glcd
// Clear Glcd
// Draw image
// Clear Glcd
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Glcd_Box(62,40,124,63,1);
Glcd_Rectangle(5,5,84,35,1);
Glcd_Line(0, 0, 127, 63, 1);
Delay2S();
counter := 5;
Libraries
// Draw box
// Draw rectangle
// Draw line
while (counter <= 59) do // Draw horizontal and vertical lines
begin
Delay_ms(250);
Glcd_V_Line(2, 54, counter, 1);
Glcd_H_Line(2, 120, counter, 1);
Counter := counter + 5;
end;
Delay2S();
Glcd_Fill(0x00);
Glcd_Set_Font(@Character8x7, 8, 7, 32);
"Character8x7"
Glcd_Write_Text('mikroE', 1, 7, 2);
// Clear Glcd
// Choose font
// Write string
for counter := 1 to 10 do
Glcd_Circle(63,32, 3*counter, 1);
Delay2S();
// Draw circles
Glcd_Box(10,20, 70,63, 2);
Delay2S();
// Draw box}
Glcd_Fill(0xFF);
Glcd_Set_Font(@Character8x7, 8, 7, 32);
someText := '8x7 Font';
Glcd_Write_Text(someText, 5, 0, 2);
delay2S();
// Fill Glcd
// Change font
// Write string
Glcd_Set_Font(@System3x6, 3, 5, 32);
someText := '3X5 CAPITALS ONLY';
Glcd_Write_Text(someText, 60, 2, 2);
delay2S();
// Change font
Glcd_Set_Font(@font5x7, 5, 7, 32);
someText := '5x7 Font';
Glcd_Write_Text(someText, 5, 4, 2);
delay2S();
// Change font
Glcd_Set_Font(@FontSystem5x7_v2, 5, 7, 32);
someText := '5x7 Font (v2)';
Glcd_Write_Text(someText, 50, 6, 2);
delay2S();
end;
// Write string
// Write string
// Change font
// Write string
end.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
305
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
HW Connection
Glcd HW connection
306
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
I²C Library
I2C full master MSSP module is available with a number of PIC MCU models. mikroPascal PRO
for PIC provides library which supports the master I2C mode.
Note: Some MCUs have multiple I2C modules. In order to use the desired I˛C library routine, simply change the number 1 in the prototype with the appropriate module number, i.e.
I2C1_Init(100000);
Library Routines
-
I2C1_Init
I2C1_Start
I2C1_Repeated_Start
I2C1_Is_Idle
I2C1_Rd
I2C1_Wr
I2C1_Stop
I2C1_Init
Prototype
procedure I2C1_Init(clock : dword);
Returns
Nothing.
Description
Initializes I2C with desired clock (refer to device data sheet for correct values in
respect with Fosc). Needs to be called before using other functions of I2C Library.
You don’t need to configure ports manually for using the module; library will take
care of the initialization.
Library requires MSSP module on PORTB or PORTC.
Requires
Example
Note: Calculation of the I2C clock value is carried out by the compiler, as it
would produce a relatively large code if performed on the libary level.
Therefore, compiler needs to know the value of the parameter in the compile
time. That is why this parameter needs to be a constant, and not a variable.
I2C1_Init(100000);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
307
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
I2C1_Start
Prototype
function I2C1_Start() : byte;
Returns
If there is no error, function returns 0.
Description Determines if I2C bus is free and issues START signal.
Requires
I˛C must be configured before using this function. See I2C1_Init.
Example
if (I2C1_Start() = 0) then
...
I2C1_Repeated_Start
Prototype
procedure I2C1_Repeated_Start();
Returns
Nothing.
Description Issues repeated START signal.
Requires
I2C must be configured before using this function. See I2C1_Init.
Example
I2C1_Repeated_Start();
I2C1_Is_Idle
Prototype
function I2C1_Is_Idle() : byte;
Returns TRUE if I2C bus is free, otherwise returns FALSE.
Description Tests if I2C bus is free.
Returns
Requires
I2C must be configured before using this function. See I2C1_Init.
Example
if (I2C1_Is_Idle) then
...
I2C1_Rd
Prototype
function I2C1_Rd(ack : byte) : byte;
Returns
Returns one byte from the slave.
Description
Reads one byte from the slave, and sends not acknowledge signal if parameter
ack is 0, otherwise it sends acknowledge.
I2C must be configured before using this function. See I2C1_Init.
Requires
Also, START signal needs to be issued in order to use this function. See I2C1_Start.
Read data and send not acknowledge signal:
Example
tmp := I2C1_Rd(0);
308
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
I2C1_Wr
Prototype
function I2C1_Wr(data : byte) : byte;
Returns
Returns 0 if there were no errors.
Description Sends data byte (parameter data) via I2C bus.
I2C must be configured before using this function. See I2C1_Init.
Requires
Example
Also, START signal needs to be issued in order to use this function. See
I2C1_Start.
I2C1_Write($A3);
I2C1_Stop
Prototype
procedure I2C1_Stop();
Returns
Nothing.
Description Issues STOP signal.
Requires
I2C must be configured before using this function. See I2C1_Init.
Example
I2C1_Stop();
Library Example
This code demonstrates use of I˛C Library procedures and functions. PIC MCU is connected
(SCL, SDA pins ) to 24c02 EEPROM. Program sends data to EEPROM (data is written at address
2). Then, we read data via I2C from EEPROM and send its value to PORTD, to check if the cycle
was successful. Check the figure below.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
309
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
program I2C_Simple;
begin
ANSEL := 0;
ANSELH := 0;
PORTB := 0;
TRISB := 0;
// Configure AN pins as digital I/O
// Configure PORTB as output
I2C1_Init(100000);
// initialize
I2C1_Start();
// issue I2C
I2C1_Wr(0xA2);
// send byte via I2C
I2C1_Wr(2);
// send byte (address
I2C1_Wr(0xF0);
// send data
I2C1_Stop();
// issue I2C
I2C communication
start signal
(device address + W)
of EEPROM location)
(data to be written)
stop signal
Delay_100ms();
I2C1_Start();
// issue I2C start signal
I2C1_Wr(0xA2);
// send byte via I2C (device address + W)
I2C1_Wr(2);
// send byte (data address)
I2C1_Repeated_Start();
// issue I2C signal repeated start
I2C1_Wr(0xA3);
// send byte (device address + R)
PORTB := I2C1_Rd(0);
// Read the data (NO acknowledge)
I2C1_Stop();
// issue I2C stop signal
end.
HW Connection
Interfacing 24c02 to PIC via I2C
310
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Keypad Library
The mikroPascal PRO for PIC provides a library for working with 4x4 keypad. The library routines
can also be used with 4x1, 4x2, or 4x3 keypad. For connections explanation see schematic at the
bottom of this page.
External dependencies of Keypad Library
The following variable
must be defined in all
projects using Keypad
Library:
var keypadPort :
byte; sfr; external;
Description:
Keypad Port.
Example :
var keypadPort : byte
at PORTD;
Library Routines
- Keypad_Init
- Keypad_Key_Press
- Keypad_Key_Click
Keypad_Init
Prototype
procedure Keypad_Init();
Returns
Nothing.
Description Initializes port for working with keypad.
Global variables :
Requires
- keypadPort_Reg - Keypad port
must be defined before using this function.
Example
// Initialize PORTB for communication with keypad
var keypadPort : byte at PORTD;
...
Keypad_Init();
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
311
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Keypad_Key_Press
Prototype
function Keypad_Key_Press(): byte;
The code of a pressed key (1..16).
Returns
If no key is pressed, returns 0.
Description Reads the key from keypad when key gets pressed.
Requires
Port needs to be initialized for working with the Keypad library, see Keypad_Init.
Example
var kp : byte;
...
kp := Keypad_Key_Press();
Keypad_Key_Click
Prototype
function Keypad_Key_Click(): byte;
The code of a clicked key (1..16).
Returns
If no key is clicked, returns 0.
Call to Keypad_Key_Click is a blocking call: the function waits until some key is
pressed and released. When released, the function returns 1 to 16, depending
Description on the key. If more than one key is pressed simultaneously the function will wait
until all pressed keys are released. After that the function will return the code of
the first pressed key.
Requires
Port needs to be initialized for working with the Keypad library, see Keypad_Init.
Example
var kp : byte;
...
kp := Keypad_Key_Click();
Library Example
This is a simple example of using the Keypad Library. It supports keypads with 1..4 rows and 1..4
columns. The code being returned by Keypad_Key_Click() function is in range from 1..16. In this
example, the code returned is transformed into ASCII codes [0..9,A..F] and displayed on Lcd. In
addition, a small single-byte counter displays in the second Lcd row number of key presses.
312
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
program Keypad_Test;
var kp, cnt, oldstate : byte;
txt : array[6] of byte;
// Keypad module connections
var keypadPort : byte at PORTD;
// End Keypad module connections
// Lcd module connections
var LCD_RS : sbit at RB4_bit;
LCD_EN : sbit at RB5_bit;
LCD_D4 : sbit at RB0_bit;
LCD_D5 : sbit at RB1_bit;
LCD_D6 : sbit at RB2_bit;
LCD_D7 : sbit at RB3_bit;
var LCD_RS_Direction : sbit at
LCD_EN_Direction : sbit at
LCD_D4_Direction : sbit at
LCD_D5_Direction : sbit at
LCD_D6_Direction : sbit at
LCD_D7_Direction : sbit at
// End Lcd module connections
TRISB4_bit;
TRISB5_bit;
TRISB0_bit;
TRISB1_bit;
TRISB2_bit;
TRISB3_bit;
begin
oldstate := 0;
cnt := 0;
// Reset counter
Keypad_Init();
// Initialize Keypad
ANSEL := 0;
// Configure AN pins as digital I/O
ANSELH := 0;
Lcd_Init();
// Initialize Lcd
Lcd_Cmd(_LCD_CLEAR);
// Clear display
Lcd_Cmd(_LCD_CURSOR_OFF);
// Cursor off
Lcd_Out(1, 1, 'Key :');
// Write message text on Lcd
Lcd_Out(2, 1, 'Times:');
while TRUE do
begin
kp := 0;
// Reset key code variable
// Wait for key to be pressed and released
while ( kp = 0 ) do
kp := Keypad_Key_Click();
// Store key code in
kp variable
// Prepare value for output, transform key to it's ASCII
value
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
313
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
case kp of
//case 10: kp = 42;
// '*'
for keypad4x3
//case 11: kp = 48;
// '0'
//case 12: kp = 35;
// '#'
//default: kp += 48;
1: kp := 49;
block for keypad4x4
2: kp := 50;
3: kp := 51;
4: kp := 65;
5: kp := 52;
6: kp := 53;
7: kp := 54;
8: kp := 66;
9: kp := 55;
10: kp := 56;
11: kp := 57;
12: kp := 67;
13: kp := 42;
14: kp := 48;
15: kp := 35;
16: kp := 68;
// 1
//
//
//
//
//
//
//
//
//
//
//
//
//
//
//
// Uncomment this block
// Uncomment this
2
3
A
4
5
6
B
7
8
9
C
*
0
#
D
end;
if (kp <> oldstate) then // Pressed key differs from previous
begin
cnt := 1;
oldstate := kp;
end
else
// Pressed key is same as previous
Inc(cnt);
Lcd_Chr(1, 10, kp);
// Print key ASCII value on Lcd
if (cnt = 255) then // If counter varialble overflow
begin
cnt := 0;
Lcd_Out(2, 10, '
');
end;
WordToStr(cnt, txt);
Lcd_Out(2, 10, txt);
// Transform counter value to string
// Display counter value on Lcd
end;
end.
314
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
HW Connection
4x4 Keypad connection scheme
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
315
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
LCD LIBRARY
The mikroPascal PRO for PIC provides a library for communication with Lcds (with
HD44780 compliant controllers) through the 4-bit interface. An example of Lcd connections is given on the schematic at the bottom of this page.
For creating a set of custom Lcd characters use Lcd Custom Character Tool.
External dependencies of Lcd Library
The following variables
must be defined in all
projects using Lcd
Library :
var LCD_RS : sbit;
sfr; external;
var LCD_EN : sbit;
sfr; external;
var LCD_D7 : sbit;
sfr; external;
var LCD_D6 : sbit;
sfr; external;
var LCD_D5 : sbit;
sfr; external;
var LCD_D4 : sbit;
sfr; external;
var LCD_RS_Direction
sbit; sfr; external;
var LCD_EN_Direction
sbit; sfr; external;
var LCD_D7_Direction
sbit; sfr; external;
var LCD_D6_Direction
sbit; sfr; external;
var LCD_D5_Direction
sbit; sfr; external;
var LCD_D4_Direction
sbit; sfr; external;
316
Description:
Example :
var LCD_RS : sbit at
RB4_bit;
var LCD_EN : sbit at
Enable line.
RB5_bit;
var LCD_D7 : sbit at
Data 7 line.
RB3_bit;
var LCD_D6 : sbit at
Data 6 line.
RB2_bit;
var LCD_D5 : sbit at
Data 5 line.
RB1_bit;
var LCD_D4 : sbit at
Data 4 line.
RB0_bit;
var LCD_RS_Direction
Register Select direction pin. : sbit at TRISB4_bit;
var LCD_EN_Direction
Enable direction pin.
: sbit at TRISB5_bit;
var LCD_D7_Direction
Data 7 direction pin.
: sbit at TRISB3_bit;
var LCD_D6_Direction
Data 6 direction pin.
: sbit at TRISB2_bit;
var LCD_D5_Direction
Data 5 direction pin.
: sbit at TRISB1_bit;
var LCD_D4_Direction
Data 4 direction pin.
: sbit at TRISB0_bit;
Register Select line.
:
:
:
:
:
:
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Routines
Lcd_Init
Lcd_Out
Lcd_Out_CP
Lcd_Chr
Lcd_Chr_Cp
Lcd_Cmd
Lcd_Init
Prototype
procedure Lcd_Init();
Returns
Nothing.
Description Initializes Lcd module.
Global variables:
Requires
-
LCD_D7: Data bit 7
LCD_D6: Data bit 6
LCD_D5: Data bit 5
LCD_D4: Data bit 4
LCD_RS: Register Select (data/instruction) signal pin
LCD_EN: Enable signal pin
LCD_D7_Direction: Direction of the Data 7 pin
LCD_D6_Direction: Direction of the Data 6 pin
LCD_D5_Direction: Direction of the Data 5 pin
LCD_D4_Direction: Direction of the Data 4 pin
LCD_RS_Direction: Direction of the Register Select pin
LCD_EN_Direction: Direction of the Enable signal pin
must be defined before using this function.
// Lcd module connections
var LCD_RS : sbit at RB4_bit;
var LCD_EN : sbit at RB5_bit;
var LCD_D4 : sbit at RB3_bit;
var LCD_D5 : sbit at RB2_bit;
var LCD_D6 : sbit at RB1_bit;
var LCD_D7 : sbit at RB0_bit;
Example
var LCD_RS_Direction : sbit at
var LCD_EN_Direction : sbit at
var LCD_D4_Direction : sbit at
var LCD_D5_Direction : sbit at
var LCD_D6_Direction : sbit at
var LCD_D7_Direction : sbit at
// End Lcd module connections
TRISB4_bit;
TRISB5_bit;
TRISB3_bit;
TRISB2_bit;
TRISB1_bit;
TRISB0_bit;
...
Lcd_Init();
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
317
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Lcd_Out
Prototype
procedure Lcd_Out(row: byte; column: byte; var text: array [20]
of char);
Returns
Nothing.
Prints text on Lcd starting from specified position. Both string variables and literals can be passed as a text.
Description
Parameters :
- row: starting position row number
- column: starting position column number
- text: text to be written
Requires
The Lcd module needs to be initialized. See Lcd_Init routine.
Example
// Write text "Hello!" on Lcd starting from row 1, column 3:
Lcd_Out(1, 3, "Hello!");
Lcd_Out_CP
Prototype
procedure Lcd_Out_CP(var text: array [20] of char);
Returns
Nothing.
Prints text on Lcd at current cursor position. Both string variables and literals
can be passed as a text.
Description
Parameters :
- text: text to be written
318
Requires
The Lcd module needs to be initialized. See Lcd_Init routine.
Example
// Write text "Here!" at current cursor position:
Lcd_Out_CP("Here!");
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Lcd_Chr
Prototype
procedure Lcd_Chr(row: byte; column: byte; out_char: byte);
Returns
Nothing.
Prints character on Lcd at specified position. Both variables and literals can be
passed as a character.
Description
Parameters :
- row: writing position row number
- column: writing position column number
- out_char: character to be written
Requires
The Lcd module needs to be initialized. See Lcd_Init routine.
Example
// Write character "i" at row 2, column 3:
Lcd_Chr(2, 3, 'i');
Lcd_Chr_CP
Prototype
procedure Lcd_Chr_CP(out_char: byte);
Returns
Nothing.
Prints character on Lcd at current cursor position. Both variables and literals
can be passed as a character.
Description
Parameters :
-out_char: character to be written
Requires
The Lcd module needs to be initialized. See Lcd_Init routine.
Example
// Write character "e" at current cursor position:
Lcd_Chr_CP('e');
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
319
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Lcd_Cmd
Prototype
procedure Lcd_Cmd(out_char: byte);
Returns
Nothing.
Sends command to Lcd.
Parameters :
Description
- out_char: command to be sent
Note: Predefined constants can be passed to the function, see Available Lcd
Commands.
Requires
The Lcd module needs to be initialized. See Lcd_Init table.
Example
// Clear Lcd display:
Lcd_Cmd(_LCD_CLEAR);
Available Lcd Commands
Lcd Command
Purpose
_LCD_FIRST_ROW
Move cursor to the 1st row
_LCD_SECOND_ROW
Move cursor to the 2nd row
_LCD_THIRD_ROW
Move cursor to the 3rd row
_LCD_FOURTH_ROW
Move cursor to the 4th row
_LCD_CLEAR
Clear display
_LCD_RETURN_HOME
Return cursor to home position, returns a shifted display to its original
position. Display data RAM is unaffected.
_LCD_CURSOR_OFF
Turn off cursor
_LCD_UNDERLINE_ON
Underline cursor on
_LCD_BLINK_CURSOR_ON
Blink cursor on
_LCD_MOVE_CURSOR_LEFT
Move cursor left without changing display data RAM
_LCD_MOVE_CURSOR_RIGHT Move cursor right without changing display data RAM
320
_LCD_TURN_ON
Turn Lcd display on
_LCD_TURN_OFF
Turn Lcd display off
_LCD_SHIFT_LEFT
Shift display left without changing display data RAM
_LCD_SHIFT_RIGHT
Shift display right without changing display data RAM
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Example
The following code demonstrates usage of the Lcd Library routines:
program
Lcd;
// LCD module connections
var LCD_RS : sbit at RB4_bit;
var LCD_EN : sbit at RB5_bit;
var LCD_D4 : sbit at RB0_bit;
var LCD_D5 : sbit at RB1_bit;
var LCD_D6 : sbit at RB2_bit;
var LCD_D7 : sbit at RB3_bit;
var LCD_RS_Direction : sbit at
var LCD_EN_Direction : sbit at
var LCD_D4_Direction : sbit at
var LCD_D5_Direction : sbit at
var LCD_D6_Direction : sbit at
var LCD_D7_Direction : sbit at
// End LCD module connections
var txt1
txt2
txt3
txt4
i
:
:
:
:
:
array[16]
array[9]
array[8]
array[7]
byte;
of
of
of
of
procedure Move_Delay();
begin
Delay_ms(500);
end;
TRISB4_bit;
TRISB5_bit;
TRISB0_bit;
TRISB1_bit;
TRISB2_bit;
TRISB3_bit;
char;
char;
char;
char;
// Loop variable
// Function used for text moving
// You can change the moving speed here
begin
TRISB := 0;
PORTB := 0xFF;
TRISB := 0xFF;
ANSEL := 0;
ANSELH := 0;
txt1
txt2
txt3
txt4
:=
:=
:=
:=
// Configure AN pins as digital I/O
'mikroElektronika';
'EasyPIC5';
'Lcd4bit';
'example';
Lcd_Init();
Lcd_Cmd(_LCD_CLEAR);
Lcd_Cmd(_LCD_CURSOR_OFF);
// Initialize LCD
// Clear display
// Cursor off
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
321
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
LCD_Out(1,6,txt3);
LCD_Out(2,6,txt4);
Delay_ms(2000);
Lcd_Cmd(_LCD_CLEAR);
// Write text in first row
// Write text in second row
LCD_Out(1,1,txt1);
Lcd_Out(2,5,txt2);
Delay_ms(500);
// Write text in first row
// Write text in second row
// Clear display
// Moving text
for i:=0 to 3 do
// Move text to the right 4 times
begin
Lcd_Cmd(_LCD_SHIFT_RIGHT);
Move_Delay();
end;
while TRUE do
// Endless loop
begin
for i:=0 to 6 do
// Move text to the left 7 times
begin
Lcd_Cmd(_LCD_SHIFT_LEFT);
Move_Delay();
end;
for i:=0 to 6 do
// Move text to the right 7 times
begin
Lcd_Cmd(_LCD_SHIFT_RIGHT);
Move_Delay();
end;
end;
end.
322
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
HW connection
Lcd HW connection
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
323
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
MANCHESTER CODE LIBRARY
The mikroPascal PRO for PIC provides a library for handling Manchester coded signals. The Manchester code is a code in which data and clock signals are combined
to form a single self-synchronizing data stream; each encoded bit contains a transition at the midpoint of a bit period, the direction of transition determines whether the
bit is 0 or 1; the second half is the true bit value and the first half is the complement
of the true bit value (as shown in the figure below).
Notes: The Manchester receive routines are blocking calls (Man_Receive_Init and
Man_Synchro). This means that MCU will wait until the task has been performed
(e.g. byte is received, synchronization achieved, etc).
Note: Manchester code library implements time-based activities, so interrupts need
to be disabled when using it.
External dependencies of Manchester Code Library
The following variables
must be defined in all
projects using Manchester Code Library:
var MANRXPIN : sbit;
sfr; external;
var MANTXPIN : sbit;
sfr; external;
var
MANRXPIN_Direction :
sbit; sfr; external;
var
MANTXPIN_Direction :
sbit; sfr; external;
324
Description:
Example :
Direction of the Receive
pin.
var MANRXPIN : sbit
at RB0_bit;
var MANTXPIN : sbit
at RB1_bit;
var
MANRXPIN_Direction :
sbit at TRISB0_bit;
Direction of the Transmit
pin.
var
MANTXPIN_Direction :
sbit at TRISB1_bit;
Receive line.
Transmit line.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Routines
-
Man_Receive_Init
Man_Receive
Man_Send_Init
Man_Send
Man_Synchro
Man_Break
The following routines are for the internal use by compiler only:
- Manchester_0
- Manchester_1
- Manchester_Out
Man_Receive_Init
Prototype
function Man_Receive_Init(): word;
Returns
- 0 - if initialization and synchronization were successful.
- 1 - upon unsuccessful synchronization.
- 255 - upon user abort.
The function configures Receiver pin and performs synchronization procedure in
order to retrieve baud rate out of the incoming signal.
Description
Note: In case of multiple persistent errors on reception, the user should call this
routine once again or Man_Synchro routine to enable synchronization.
Global variables :
Requires
- MANRXPIN : Receive line
- MANRXPIN_Direction : Direction of the receive pin
must be defined before using this function.
Example
// Initialize Receiver
var MANRXPIN : sbit at RB0_bit;
var MANRXPIN_Direction : sbit at TRISB0_bit;
...
Man_Receive_Init();
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
325
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Man_Receive
Prototype
function Man_Receive(var error: byte): byte;
Returns
A byte read from the incoming signal.
The function extracts one byte from incoming signal.
Description
Parameters :
- error: error flag. If signal format does not match the expected, the error flag
will be set to non-zero.
Requires
Example
To use this function, the user must prepare the MCU for receiving. See
Man_Receive_Init.
var data, error : byte
...
data := 0
error := 0
data := Man_Receive(&error);
if (error <> 0) then
begin
// error handling
end;
Man_Send_Init
Prototype
procedure Man_Send_Init();
Returns
Nothing.
Description The function configures Transmitter pin.
Global variables :
Requires
- MANRXPIN : Receive line
- MANRXPIN_Direction : Direction of the receive pin
must be defined before using this function.
Example
326
// Initialize Transmitter:
var MANTXPIN : sbit at RB1_bit;
var MANTXPIN_Direction : sbit at TRISB1_bit;
...
Man_Send_Init();
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Man_Send
Prototype
procedure Man_Send(tr_data: byte);
Returns
Nothing.
Sends one byte.
Parameters :
Description
- tr_data: data to be sent
Note: Baud rate used is 500 bps.
Requires
To use this function, the user must prepare the MCU for sending. See
Man_Send_Init.
Example
var msg : byte;
...
Man_Send(msg);
Man_Synchro
Prototype
function Man_Synchro(): byte;
Returns
- 0 - if synchronization was not successful.
- Half of the manchester bit length, given in multiples of 10us - upon successful
synchronization.
Description Measures half of the manchester bit length with 10us resolution.
Requires
To use this function, you must first prepare the MCU for receiving. See
Man_Receive_Init.
Example
var man__half_bit_len : word;
...
man__half_bit_len := Man_Synchro();
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
327
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Man_Break
Prototype
procedure Man_Break();
Returns
Nothing.
Description
Man_Receive is blocking routine and it can block the program flow. Call this
routine from interrupt to unblock the program execution. This mechanism is similar to WDT.
Note: Interrupts should be disabled before using Manchester routines again
(see note at the top of this page).
Requires
Nothing.
var data1, error, counter : byte;
procedure interrupt();
begin
if (INTCON.T0IF <> 0) then
if (counter >= 20) then
begin
Man_Break();
counter := 0;
end
else
Inc(counter);
INTCON.T0IF := 0;
rupt flag
end;
Example
begin
counter := 0;
OPTION_REG := 0x04;
// reset counter
// increment counter
// Clear Timer0 overflow inter-
// TMR0 prescaler set to 1:32
...
Man_Receive_Init();
...
// try Man_Receive with blocking
INTCON.GIE := 1;
//
INTCON.T0IE := 1;
//
rupt
data1 := Man_Receive(error);
INTCON.GIE := 0;
//
end.
328
prevention mechanism
Global interrupt enable
Enable Timer0 overflow inter-
Global interrupt disable
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Example
The following code is code for the Manchester receiver, it shows how to use the
Manchester Library for receiving data:
program Manchester_Receiver;
// LCD module connections
var LCD_RS : sbit at RB4_bit;
LCD_EN : sbit at RB5_bit;
LCD_D4 : sbit at RB0_bit;
LCD_D5 : sbit at RB1_bit;
LCD_D6 : sbit at RB2_bit;
LCD_D7 : sbit at RB3_bit;
var LCD_RS_Direction : sbit at
LCD_EN_Direction : sbit at
LCD_D4_Direction : sbit at
LCD_D5_Direction : sbit at
LCD_D6_Direction : sbit at
LCD_D7_Direction : sbit at
// End LCD module connections
TRISB4_bit;
TRISB5_bit;
TRISB0_bit;
TRISB1_bit;
TRISB2_bit;
TRISB3_bit;
// Manchester module connections
var MANRXPIN : sbit at RB0_bit;
MANRXPIN_Direction : sbit at TRISB0_bit;
MANTXPIN : sbit at RB1_bit;
MANTXPIN_Direction : sbit at TRISB1_bit;
// End Manchester module connections
var error, ErrorCount, temp : byte;
begin
ErrorCount := 0;
ANSEL := 0;
ANSELH := 0;
C1ON_bit := 0;
C2ON_bit := 0;
Lcd_Init();
Lcd_Cmd(_LCD_CLEAR);
// Configure AN pins as digital I/O
// Disable comparators
// Initialize LCD
// Clear LCD display
Man_Receive_Init();
// Initialize Receiver
while TRUE do
begin
Lcd_Cmd(_LCD_FIRST_ROW);
// Endless loop
while TRUE do
begin
// Move cursor to the 1st row
// Wait for the "start" byte
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
329
CHAPTER 7
Libraries
mikroPASCAL PRO for PIC
temp := Man_Receive(error);
// Attempt byte receive
if (temp = 0x0B) then
// "Start" byte, see
Transmitter example
break;
// We got the starting sequence
if (error <> 0) then // Exit so we do not loop forever
break;
end;
repeat
begin
temp := Man_Receive(error);
// Attempt byte receive
if (error <> 0) then
// If error occured
begin
Lcd_Chr_CP('?');
// Write question mark on LCD
Inc(ErrorCount);
// Update error counter
if (ErrorCount > 20) then
// In case of multiple errors
begin
temp := Man_Synchro();
// Try to synchronize
again
//Man_Receive_Init();
// Alternative, try to
Initialize Receiver again
ErrorCount := 0;
// Reset error counter
end;
end
else
// No error occured
begin
if (temp <> 0x0E) then
// If "End" byte was
received(see Transmitter example)
Lcd_Chr_CP(temp);
//
do not write received
byte on LCD
end;
Delay_ms(25);
end;
until ( temp = 0x0E );
end;
// If "End" byte was received exit do loop
end.
The following code is code for the Manchester transmitter, it shows how to use the
Manchester Library for transmitting data:
330
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
program Manchester_Transmitter;
// Manchester module connections
var MANRXPIN : sbit at RB0_bit;
MANRXPIN_Direction : sbit at TRISB0_bit;
MANTXPIN : sbit at RB1_bit;
MANTXPIN_Direction : sbit at TRISB1_bit;
// End Manchester module connections
var index, character : byte;
s1 : array[17] of char;
begin
s1 := 'mikroElektronika';
ANSEL := 0;
// Configure AN pins as digital I/O
ANSELH := 0;
C1ON_bit := 0;
// Disable comparators
C2ON_bit := 0;
Man_Send_Init();
while TRUE do
begin
Man_Send(0x0B);
Delay_ms(100);
// Initialize transmitter
// Endless loop
// Send "start" byte
// Wait for a while
character := s1[0];
// Take first char from string
index := 0;
// Initialize index variable
while (character <> 0) do
// String ends with zero
begin
Man_Send(character);
// Send character
Delay_ms(90);
// Wait for a while
Inc(index);
// Increment index variable
character := s1[index]; // Take next char from string
end;
Man_Send(0x0E);
// Send "end" byte
Delay_ms(1000);
end;
end.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
331
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Connection Example
Simple Transmitter connection
Simple Receiver connection
332
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
MULTI MEDIA CARD LIBRARY
The Multi Media Card (MMC) is a flash memory card standard. MMC cards are currently available in sizes up to and including 1 GB, and are used in cell phones, mp3
players, digital cameras, and PDA’s.
mikroPascal PRO for PIC provides a library for accessing data on Multi Media Card
via SPI communication.This library also supports SD(Secure Digital) memory cards.
Secure Digital Card
Secure Digital (SD) is a flash memory card standard, based on the older Multi Media
Card (MMC) format.
SD cards are currently available in sizes of up to and including 2 GB, and are used
in cell phones, mp3 players, digital cameras, and PDAs.
Notes:
- Library works with PIC18 family only;
- The library uses the SPI module for communication. User must initialize SPI
module before using the SPI Graphic Lcd Library.
For MCUs with two SPI modules it is possible to initialize both of them and then
switch by using the SPI_Set_Active() routine.
- Routines for file handling can be used only with FAT16 file system.
- Library functions create and read files from the root directory only;
- Library functions populate both FAT1 and FAT2 tables when writing to files, but the
file data is being read from the FAT1 table only; i.e. there is no recovery if FAT1
table is corrupted.
Note: The SPI module has to be initialized through SPI1_Init_Advanced routine with
the following parameters:
-
SPI Master
8bit mode
primary prescaler 16
Slave Select disabled
data sampled in the middle of data output time
clock idle low
Serial output data changes on transition from idle clock state to active clock state
SPI1_Init_Advanced(_SPI_MASTER_OSC_DIV16, _SPI_DATA_SAMPLE_MIDDLE,
_SPI_CLK_IDLE_LOW, _SPI_LOW_2_HIGH); must be called before initializing
Mmc_Init.
Note: Once the MMC/SD card is initialized, the user can reinitialize SPI at higher
speed. See the Mmc_Init and Mmc_Fat_Init routines.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
333
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
External dependencies of MMC Library
The following variable
must be defined in all
projects using MMC
library:
Description:
var Mmc_Chip_Select :
Chip select pin.
sbit; sfr; external;
Example :
var Mmc_Chip_Select :
sbit at RC2_bit;
var
var
Mmc_Chip_Select_Direc Direction of the chip select Mmc_Chip_Select_Direc
tion : sbit; sfr;
tion : sbit at
pin.
external;
TRISC0_bit;
Library Routines
-
Mmc_Init
Mmc_Read_Sector
Mmc_Write_Sector
Mmc_Read_Cid
Mmc_Read_Csd
Routines for file handling:
-
334
Mmc_Fat_Init
Mmc_Fat_QuickFormat
Mmc_Fat_Assign
Mmc_Fat_Reset
Mmc_Fat_Read
Mmc_Fat_Rewrite
Mmc_Fat_Append
Mmc_Fat_Delete
Mmc_Fat_Write
Mmc_Fat_Set_File_Date
Mmc_Fat_Get_File_Date
Mmc_Fat_Get_File_Size
Mmc_Fat_Get_Swap_File
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Mmc_Init
Prototype
function Mmc_Init(): byte;
Returns
- 0 - if MMC/SD card was detected and successfully initialized
- 1 - otherwise
Initializes MMC through hardware SPI interface.
Description
Parameters:
- port: chip select signal port address.
- cspin: chip select pin.
Global variables :
Requires
- Mmc_Chip_Select: Chip Select line
- Mmc_Chip_Select_Direction: Direction of the Chip Select pin
must be defined before using this function.
The appropriate hardware SPI module must be previously initialized. See the
SPI1_Init, SPI1_Init_Advanced routines.
// MMC module connections
var Mmc_Chip_Select : sbit at RC2_bit;
var Mmc_Chip_Select_Direction : sbit at TRISC2_bit;
// MMC module connections
Example
error = Mmc_Init();
var i : byte;
...
SPI1_Init();
i = Mmc_Init();
// Init with CS line at RC.2
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
335
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Mmc_Read_Sector
Prototype
function Mmc_Read_Sector(sector: longint; var dbuff: array[512]
of byte): byte;
Returns
- 0 - if reading was successful
- 1 - if an error occurred
The function reads one sector (512 bytes) from MMC card.
Description
Parameters:
- sector: MMC/SD card sector to be read.
- data: buffer of minimum 512 bytes in length for data storage.
Requires
MMC/SD card must be initialized. See Mmc_Init.
Example
// read sector 510 of the MMC/SD card
var error : byte;
sectorNo : longint;
dataBuffer : array[512] of byte;
...
sectorNo := 510;
error := Mmc_Read_Sector(sectorNo, dataBuffer);
Mmc_Write_Sector
Prototype
function Mmc_Write_Sector(sector: longint; var data_: array[512]
of byte): byte;
Returns
- 0 - if writing was successful
- 1 - if there was an error in sending write command
- 2 - if there was an error in writing (data rejected)
The function writes 512 bytes of data to one MMC card sector.
Description
Parameters:
- sector: MMC/SD card sector to be written to.
- data: data to be written (buffer of minimum 512 bytes in length).
336
Requires
MMC/SD card must be initialized. See Mmc_Init.
Example
// write to sector 510 of the MMC/SD card
var error : byte;
sectorNo : longint;
dataBuffer : array[512] of byte;
...
sectorNo := 510;
error := Mmc_Write_Sector(sectorNo, dataBuffer);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Mmc_Read_Cid
Prototype
function Mmc_Read_Cid(var data_cid: array[16] of byte): byte;
Returns
- 0 - if CID register was read successfully
- 1 - if there was an error while reading
The function reads 16-byte CID register.
Description Parameters:
- data_cid: buffer of minimum 16 bytes in length for storing CID register content.
Requires
MMC/SD card must be initialized. See Mmc_Init.
Example
var error : byte;
dataBuffer : array[16] of byte;
...
error := Mmc_Read_Cid(dataBuffer);
Mmc_Read_Csd
Prototype
function Mmc_Read_Csd(var data_for_registers: array[16] of byte):
byte;
Returns
- 0 - if CSD register was read successfully
- 1 - if there was an error while reading
The function reads 16-byte CSD register.
Description
Parameters:
- data_for_registers: buffer of minimum 16 bytes in length for storing CSD
register content.
Requires
MMC/SD card must be initialized. See Mmc_Init.
Example
var error : word;
data_for_registers : array[16] of byte;
...
error := Mmc_Read_Csd(data_for_registers);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
337
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Mmc_Fat_Init
Prototype
function Mmc_Fat_Init(): byte;
Returns
- 0 - if MMC/SD card was detected and successfully initialized
- 1 - if FAT16 boot sector was not found
- 255 - if MMC/SD card was not detected
Description
Initializes MMC/SD card, reads MMC/SD FAT16 boot sector and extracts necessary data needed by the library.
Note: MMC/SD card has to be formatted to FAT16 file system.
Global variables :
Requires
- Mmc_Chip_Select: Chip Select line
- Mmc_Chip_Select_Direction: Direction of the Chip Select pin
must be defined before using this function.
The appropriate hardware SPI module must be previously initialized. See the
SPI1_Init, SPI1_Init_Advanced routines.
// MMC module connections
var Mmc_Chip_Select : sbit at RC2_bit;
var Mmc_Chip_Select_Direction : sbit at TRISC2_bit;
// MMC module connections
SPI1_Init();
Example
// init the FAT library
if (Mmc_Fat_Init() = 0) then
begin
SPI1_Init();
...
end
338
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Mmc_Fat_QuickFormat
Prototype
function Mmc_Fat_QuickFormat(var mmc_fat_label : string[11]) : byte;
Returns
- 0 - if MMC/SD card was detected, successfully formated and initialized
- 1 - if FAT16 format was unseccessful
- 255 - if MMC/SD card was not detected
Formats to FAT16 and initializes MMC/SD card.
Parameters:
- port: chip select signal port address.
- pin: chip select pin.
- mmc_fat_label: volume label (11 characters in length). If less than 11
characters are provided, the label will be padded with spaces. If an empty
Description
string is passed, the volume will not be labeled.
Note: This routine can be used instead or in conjunction with the Mmc_Fat_Init
routine.
Note: If MMC/SD card already contains a valid boot sector, it will remain
unchanged (except volume label field) and only FAT and ROOT tables will be
erased. Also, the new volume label will be set.
Requires
The appropriate hardware SPI module must be previously initialized.
Example
// format and initialize the FAT library
if (Mmc_Fat_QuickFormat('mikroE') = 0) then
begin
...
end;
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
339
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Mmc_Fat_Assign
Prototype
function Mmc_Fat_Assign(var filename: array[12] of char;
file_cre_attr: byte): byte;
Returns
- 1 - if file already exists or file does not exist but a new file is created.
- 0 - if file does not exist and no new file is created.
Assigns file for file operations (read, write, delete...). All subsequent file operations will be applied on an assigned file.
Parameters:
- filename: name of the file that should be assigned for file operations. File
name should be in DOS 8.3 (file_name.extension) format. The file name and
extension will be automatically padded with spaces by the library if they have
less than length required (i.e. "mikro.tx" -> "mikro .tx "), so the user does not
have to take care of that. The file name and extension are case insensitive.
The library will convert them to proper case automatically, so the user does not
have to take care of that.
Also, in order to keep backward compatibility with the first version of this
library, file names can be entered as UPPERCASE string of 11 bytes in length
with no dot character between file name and extension (i.e. "MIKROELETXT"
-> MIKROELE.TXT). In this case last 3 characters of the string are considered
to be file extension.
- file_cre_attr: file creation and attributs flags. Each bit corresponds to the
Description
appropriate file attribut:
Bit
Mask
Description
0
0x01
Read Only
1
0x02
Hidden
2
0x04
System
3
0x08
Volume Label
4
0x10
Subdirectory
5
0x20
Archive
6
0x40
Device (internal use only, never found on disk)
7
0x80
File creation flag. If the file does not exist and this flag is set,
a new file with specified name will be created.
Note: Long File Names (LFN) are not supported.
340
Requires
MMC/SD card and MMC library must be initialized for file operations. See
Mmc_Fat_Init.
Example
// create file with archive attribut if it does not already exist
Mmc_Fat_Assign('MIKRO007.TXT',0xA0);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Mmc_Fat_Reset
Prototype
procedure Mmc_Fat_Reset(var size: dword);
Returns
Nothing.
Opens currently assigned file for reading.
Description
Parameters:
- size: buffer to store file size to. After file has been open for reading, its size is
returned through this parameter.
Requires
MMC/SD card and MMC library must be initialized for file operations. See
Mmc_Fat_Init.
The file must be previously assigned. See Mmc_Fat_Assign.
Example
var size : dword;
...
Mmc_Fat_Reset(size);
Mmc_Fat_Read
Prototype
procedure Mmc_Fat_Read(var bdata: byte);
Returns
Nothing.
Reads a byte from the currently assigned file opened for reading. Upon function
execution, file pointers will be set to the next character in the file.
Description Parameters:
- bdata: buffer to store read byte to. Upon this function execution read byte is
returned through this parameter.
MMC/SD card and MMC library must be initialized for file operations. See
Mmc_Fat_Init.
Requires
The file must be previously assigned. See Mmc_Fat_Assign.
The file must be opened for reading. See Mmc_Fat_Reset.
Example
var character : byte;
...
Mmc_Fat_Read(character);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
341
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Mmc_Fat_Rewrite
Prototype
procedure Mmc_Fat_Rewrite();
Returns
Nothing.
Description
Opens the currently assigned file for writing. If the file is not empty its content
will be erased.
Requires
MMC/SD card and MMC library must be initialized for file operations. See
Mmc_Fat_Init.
The file must be previously assigned. See Mmc_Fat_Assign.
Example
// open file for writing
Mmc_Fat_Rewrite();
Mmc_Fat_Append
Prototype
procedure Mmc_Fat_Append();
Returns
Nothing.
Opens the currently assigned file for appending. Upon this function execution
Description file pointers will be positioned after the last byte in the file, so any subsequent
file writing operation will start from there.
Requires
MMC/SD card and MMC library must be initialized for file operations. See
Mmc_Fat_Init.
The file must be previously assigned. See Mmc_Fat_Assign.
Example
// open file for appending
Mmc_Fat_Append();
Mmc_Fat_Delete
Prototype
procedure Mmc_Fat_Delete();
Returns
Nothing.
Description Deletes currently assigned file from MMC/SD card.
Requires
MMC/SD card and MMC library must be initialized for file operations. See
Mmc_Fat_Init.
The file must be previously assigned. See Mmc_Fat_Assign.
Example
342
// delete current file
Mmc_Fat_Delete();
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Mmc_Fat_Write
Prototype
procedure Mmc_Fat_Write(var fdata: array[512] of byte; data_len:
word);
Returns
Nothing.
Writes requested number of bytes to the currently assigned file opened for writing.
Description
Parameters:
- fdata: data to be written.
- data_len: number of bytes to be written.
MMC/SD card and MMC library must be initialized for file operations. See
Mmc_Fat_Init.
Requires
The file must be previously assigned. See Mmc_Fat_Assign.
The file must be opened for writing. See Mmc_Fat_Rewrite or
Mmc_Fat_Append.
Example
var file_contents : array[42] of byte;
...
Mmc_Fat_Write(file_contents, 42); // write data to the assigned file
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
343
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Mmc_Fat_Set_File_Date
Prototype
procedure Mmc_Fat_Set_File_Date(year: word; month: byte; day:
byte; hours: byte; mins: byte; seconds: byte);
Returns
Nothing.
Sets the date/time stamp. Any subsequent file writing operation will write this
stamp to the currently assigned file's time/date attributs.
Parameters:
Description -
year: year attribute. Valid values: 1980-2107
month: month attribute. Valid values: 1-12
day: day attribute. Valid values: 1-31
hours: hours attribute. Valid values: 0-23
mins: minutes attribute. Valid values: 0-59
seconds: seconds attribute. Valid values: 0-59
MMC/SD card and MMC library must be initialized for file operations. See
Mmc_Fat_Init.
Requires
The file must be previously assigned. See Mmc_Fat_Assign.
The file must be opened for writing. See Mmc_Fat_Rewrite or
Mmc_Fat_Append.
Example
344
Mmc_Fat_Set_File_Date(2005,9,30,17,41,0);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Mmc_Fat_Get_File_Date
Prototype
procedure Mmc_Fat_Get_File_Date(var year: word; var month: byte;
var day: byte; var hours: byte; var mins: byte);
Returns
Nothing.
Reads time/date attributes of the currently assigned file.
Parameters:
- year: buffer to store year attribute to. Upon function execution year attribute is
returned through this parameter.
- month: buffer to store month attribute to. Upon function execution month
Description
attribute is returned through this parameter.
- day: buffer to store day attribute to. Upon function execution day attribute is
returned through this parameter.
- hours: buffer to store hours attribute to. Upon function execution hours
attribute is returned through this parameter.
- mins: buffer to store minutes attribute to. Upon function execution minutes
attribute is returned through this parameter.
Requires
MMC/SD card and MMC library must be initialized for file operations. See
Mmc_Fat_Init.
The file must be previously assigned. See Mmc_Fat_Assign.
Example
var year : word;
month, day, hours, mins : byte;
...
Mmc_Fat_Get_File_Date(year, month, day, hours, mins);
Mmc_Fat_Get_File_Size
Prototype
function Mmc_Fat_Get_File_Size(): dword;
Returns
Size of the currently assigned file in bytes.
Description This function reads size of the currently assigned file in bytes.
Requires
MMC/SD card and MMC library must be initialized for file operations. See
Mmc_Fat_Init.
The file must be previously assigned. See Mmc_Fat_Assign.
Example
var my_file_size : dword;
...
my_file_size := Mmc_Fat_Get_File_Size();
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
345
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Mmc_Fat_Get_Swap_File
Prototype
function Mmc_Fat_Get_Swap_File(sectors_cnt: dword; var filename :
string[11]; file_attr : byte) : dword;
Returns
- Number of the start sector for the newly created swap file, if there was enough
free space on the MMC/SD card to create file of required size.
- 0 - otherwise.
This function is used to create a swap file of predefined name and size on the
MMC/SD media. If a file with specified name already exists on the media,
search for consecutive sectors will ignore sectors occupied by this file. Therefore, it is recommended to erase such file if it already exists before calling this
function. If it is not erased and there is still enough space for a new swap file,
this function will delete it after allocating new memory space for a new swap file.
The purpose of the swap file is to make reading and writing to MMC/SD media
as fast as possible, by using the Mmc_Read_Sector() and Mmc_Write_Sector()
functions directly, without potentially damaging the FAT system. The swap file
can be considered as a "window" on the media where the user can freely
write/read data. Its main purpose in the mikroPascal's library is to be used for
fast data acquisition; when the time-critical acquisition has finished, the data
can be re-written into a "normal" file, and formatted in the most suitable way.
Parameters:
Description - sectors_cnt: number of consecutive sectors that user wants the swap file to
have.
- filename: name of the file that should be assigned for file operations. File
name should be in DOS 8.3 (file_name.extension) format. The file name and
extension will be automatically padded with spaces by the library if they have
less than length required (i.e. "mikro.tx" -> "mikro .tx "), so the user does not
have to take care of that. The file name and extension are case insensitive.
The library will convert them to proper case automatically, so the user does not
have to take care of that.
Also, in order to keep backward compatibility with the first version of this
library, file names can be entered as UPPERCASE string of 11 bytes in length
with no dot character between file name and extension (i.e. "MIKROELETXT" > MIKROELE.TXT). In this case the last 3 characters of the string are
considered to be file extension.
- file_attr: file creation and attributs flags. Each bit corresponds to the appropriate file attribut:
346
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Description
Libraries
Bit
Mask
Description
0
0x01
Read Only
1
0x02
Hidden
2
0x04
System
3
0x08
Volume Label
4
0x10
Subdirectory
5
0x20
Archive
6
0x40
Device (internal use only, never found on disk)
7
0x80
Not used
Note: Long File Names (LFN) are not supported.
Requires
MMC/SD card and MMC library must be initialized for file operations. See
Mmc_Fat_Init.
Example
//-------------- Try to create a swap file with archive atribute,
whose size will be at least 1000 sectors.
//
If it succeeds, it sends No. of start sector
over USART
var size : dword;
...
size := Mmc_Fat_Get_Swap_File(1000, 'mikroE.txt', 0x20);
if (size <> 0) then
begin
UART1_Write(0xAA);
UART1_Write(Lo(size));
UART1_Write(Hi(size));
UART1_Write(Higher(size));
UART1_Write(Highest(size));
UART1_Write(0xAA);
end;
Library Example
The following example demonstrates MMC library test. Upon flashing, insert a MMC/SD card into
the module, when you should receive the "Init-OK" message. Then, you can experiment with
MMC read and write functions, and observe the results through the Usart Terminal.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
347
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
program MMC_Test;
{$DEFINE RS232_debug}
var MMC_chip_select : sbit at RC2_bit;
var MMC_chip_select_direction : sbit at TRISC2_bit;
const
var
var
var
FILL_CHAR = 'm';
i, SectorNo : word;
mmc_error : byte;
data_ok : bit;
// Variables for MMC routines
SectorData : array[512] of byte; // Buffer for MMC sector
reading/writing
data_for_registers : array[16] of byte; // buffer for CID and CSD
registers
// UART write text and new line (carriage return + line feed)
procedure UART_Write_Line( var uart_text : byte );
begin
UART1_Write_Text(uart_text);
UART1_Write(13);
UART1_Write(10);
end;
// Display byte in hex
// Display byte in hex
procedure printhex( i : byte );
var high, low : byte;
begin
high := i and 0xF0;
high := high shr 4;
high := high + '0';
if ( high > '9' ) then
high := high + 7;
low := (i and 0x0F) + '0';
if ( low > '9' ) then
low := low + 7 ;
// High nibble
// Low nibble
UART1_Write(high);
UART1_Write(low);
end;
begin
ADCON1 := ADCON1 or 0x0F;
CMCON := CMCON or 7;
348
// Configure AN pins as digital
// Turn off comparators
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
// Initialize UART1 module
UART1_Init(19200);
Delay_ms(10);
UART_Write_Line('PIC-Started'); // PIC present report
// Initialize SPI1 module
SPI1_Init_Advanced(_SPI_MASTER_OSC_DIV64, _SPI_DATA_SAMPLE_MIDDLE,
_SPI_CLK_IDLE_LOW, _SPI_LOW_2_HIGH);
// initialise a MMC card
mmc_error := Mmc_Init();
if ( mmc_error = 0 ) then
UART_Write_Line('MMC Init-OK')
// If MMC present report
else
UART_Write_Line('MMC Init-error'); // If error report
// Fill MMC buffer with same characters
for i := 0 to 511 do
SectorData[i] := FILL_CHAR;
// Write sector
mmc_error := Mmc_Write_Sector(SectorNo, SectorData);
if ( mmc_error = 0 ) then
UART_Write_Line('Write-OK')
else // if there are errors.....
UART_Write_Line('Write-Error');
// Reading of CID register
mmc_error := Mmc_Read_Cid(data_for_registers);
if ( mmc_error = 0 ) then
begin
UART1_Write_Text('CID : ');
for i := 0 to 15 do
printhex(data_for_registers[i]);
UART_Write_Line(' ');
end
else
UART_Write_Line('CID-error');
// Reading of CSD register
mmc_error := Mmc_Read_Csd(data_for_registers);
if ( mmc_error = 0 ) then
begin
UART1_Write_Text('CSD : ');
for i := 0 to 15 do
printhex(data_for_registers[i]);
UART_Write_Line(' ');
end
else
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
349
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
UART_Write_Line('CSD-error');
// Read sector
mmc_error := Mmc_Read_Sector(SectorNo, SectorData);
if ( mmc_error = 0 ) then
UART_Write_Line('Read-OK')
else // if there are errors.....
UART_Write_Line('Read-Error');
// Chech data match
data_ok := 1;
for i := 0 to 511 do
begin
UART1_Write(SectorData[i]);
if (SectorData[i] <> FILL_CHAR) then
begin
data_ok := 0;
break;
end;
end;
if ( data_ok <> 0 ) then
UART_Write_Line('Content-OK')
else
UART_Write_Line('Content-Error');
// Signal test end
UART_Write_Line('Test End.');
end.
HW Connection
Pin diagram of MMC memory card
350
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
ONEWIRE LIBRARY
The OneWire library provides routines for communication via the Dallas OneWire
protocol, for example with DS18x20 digital thermometer. OneWire is a Master/Slave
protocol, and all communication cabling required is a single wire. OneWire enabled
devices should have open collector drivers (with single pull-up resistor) on the
shared data line.
Slave devices on the OneWire bus can even get their power supply from data line.
For detailed schematic see device datasheet.
Some basic characteristics of this protocol are:
-
single master system,
low cost,
low transfer rates (up to 16 kbps),
fairly long distances (up to 300 meters),
small data transfer packages.
Each OneWire device has also a unique 64-bit registration number (8-bit device
type, 48-bit serial number and 8-bit CRC), so multiple slaves can co-exist on the
same bus.
Note: Oscillator frequency Fosc needs to be at least 8MHz in order to use the routines with Dallas digital thermometers.
Note: This library implements time-based activities, so interrupts need to be disabled when using OneWire library.
Library Routines
- Ow_Reset
- Ow_Read
- Ow_Write
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
351
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Ow_Reset
Prototype
function Ow_Reset(var port : byte; pin : byte) : byte;
Returns
0 if DS1820 is present, and 1 if not present.
Description
Issues OneWire reset signal for DS1820. Parameters port and pin specify the
location of DS1820.
Requires
Works with Dallas DS1820 temperature sensor only.
To reset the DS1820 that is connected to the RA5 pin:
Example
Ow_Reset(PORTA, 5);
Ow_Read
Prototype
function Ow_Read(var port : byte; pin : byte) : byte;
Returns
Data read from an external device over the OneWire bus.
Description Reads one byte of data via the OneWire bus.
Requires
Works with Dallas DS1820 temperature sensor only.
Example
tmp := Ow_Read(PORTA, 5);
Ow_Write
Prototype
procedure Ow_Write(var port : byte; pin, par : byte);
Returns
Nothing.
Description Writes one byte of data (argument par) via OneWire bus.
Requires
Works with Dallas DS1820 temperature sensor only.
Example
Ow_Write(PORTA, 5, $CC);
Library Example
This example reads the temperature using DS18x20 connected to pin PORTA.5. After reset, MCU
obtains temperature from the sensor and prints it on the Lcd. Make sure to pull-up PORTA.5 line
and to turn off the PORTA LEDs.
352
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
program OneWire;
// LCD module connections
var LCD_RS : sbit at RB4_bit;
LCD_EN : sbit at RB5_bit;
LCD_D4 : sbit at RB0_bit;
LCD_D5 : sbit at RB1_bit;
LCD_D6 : sbit at RB2_bit;
LCD_D7 : sbit at RB3_bit;
LCD_RS_Direction : sbit at
LCD_EN_Direction : sbit at
LCD_D4_Direction : sbit at
LCD_D5_Direction : sbit at
LCD_D6_Direction : sbit at
LCD_D7_Direction : sbit at
// End LCD module connections
TRISB4_bit;
TRISB5_bit;
TRISB0_bit;
TRISB1_bit;
TRISB2_bit;
TRISB3_bit;
//
Set TEMP_RESOLUTION to the corresponding resolution of used
DS18x20 sensor:
// 18S20: 9 (default setting; can be 9,10,11,or 12)
// 18B20: 12
const TEMP_RESOLUTION : byte = 9;
var text : array[9] of byte;
temp : word;
procedure Display_Temperature( temp2write : word );
const RES_SHIFT = TEMP_RESOLUTION - 8;
var temp_whole : byte;
temp_fraction : word;
begin
text := '000.0000';
// check if temperature is negative
if (temp2write and 0x8000) then
begin
text[0] := '-';
temp2write := not temp2write + 1;
end;
// extract temp_whole
temp_whole := word(temp2write shr RES_SHIFT);
// convert temp_whole to characters
if ( temp_whole div 100 ) then
text[0] := temp_whole div 100
else
text[0] := '0';
+ 48
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
353
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
text[1] := (temp_whole div 10)mod 10 + 48;
// Extract tens digit
text[2] := temp_whole mod 10
+ 48; // Extract ones digit
// extract temp_fraction and convert it to unsigned int
temp_fraction := word(temp2write shl (4-RES_SHIFT));
temp_fraction := temp_fraction and 0x000F;
temp_fraction := temp_fraction * 625;
// convert temp_fraction to characters
text[4] := word(temp_fraction div 1000)
+ 48;
Extract thousands digit
text[5] := word((temp_fraction div 100)mod 10 + 48);
Extract hundreds digit
text[6] := word((temp_fraction div 10)mod 10
+ 48);
Extract tens digit
text[7] := word(temp_fraction mod 10)
+ 48;
Extract ones digit
//
//
//
//
// print temperature on LCD
Lcd_Out(2, 5, text);
end;
begin
ANSEL := 0;
ANSELH := 0;
// Configure AN pins as digital I/O
text := '000.0000';
Lcd_Init();
Lcd_Cmd(_LCD_CLEAR);
Lcd_Cmd(_LCD_CURSOR_OFF);
Lcd_Out(1, 1, ' Temperature:
// Initialize Lcd
// Clear Lcd
// Turn cursor off
');
Lcd_Chr(2,13,223);
// Print degree character, 'C' for Centigrades
// different Lcd displays have different char code for degree
Lcd_Chr(2,14,'C');
// if you see greek alpha letter try typing
178 instead of 223
//--- main loop
while (TRUE) do
begin
//--- perform temperature reading
Ow_Reset(PORTA, 5);
// Onewire reset signal
Ow_Write(PORTA, 5, 0xCC);
// Issue command SKIP_ROM
Ow_Write(PORTA, 5, 0x44);
// Issue command CONVERT_T
Delay_us(120);
354
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Ow_Reset(PORTA, 5);
Ow_Write(PORTA, 5, 0xCC);
Ow_Write(PORTA, 5, 0xBE);
// Issue command SKIP_ROM
// Issue command READ_SCRATCHPAD
temp := Ow_Read(PORTA, 5);
temp := (Ow_Read(PORTA, 5) shl 8) + temp;
//--- Format and display result on Lcd
Display_Temperature(temp);
Delay_ms(520);
end;
end.
HW Connection
Example of DS1820 connection
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
355
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
PORT EXPANDER LIBRARY
The mikroPascal PRO for PIC provides a library for communication with the
Microchip’s Port Expander MCP23S17 via SPI interface. Connections of the PIC
compliant MCU and MCP23S17 is given on the schematic at the bottom of this
page.
Note: Library uses the SPI module for communication. The user must initialize SPI
module before using the Port Expander Library.
Note: Library does not use Port Expander interrupts.
External dependencies of Port Expander Library
The following variables
must be defined in all
projects using Port
Expander Library:
var SPExpanderRST :
sbit; sfr; external;
var SPExpanderCS :
sbit; sfr; external;
Description:
Reset line.
Chip Select line.
Example :
var SPExpanderRST :
sbit at RC0_bit;
var SPExpanderCS :
sbit at RC1_bit;
var
SPExpanderRST_Directi
Direction of the Reset pin.
on : sbit; sfr;
external;
var
SPExpanderRST_Directi
on : sbit at
TRISC0_bit;
var
Direction of the Chip
SPExpanderCS_Direction
: sbit; sfr; external; Select pin.
var
SPExpanderCS_Direction
: sbit at TRISC1_bit;
Library Routines
-
356
Expander_Init
Expander_Read_Byte
Expander_Write_Byte
Expander_Read_PortA
Expander_Read_PortB
Expander_Read_PortAB
Expander_Write_PortA
Expander_Write_PortB
Expander_Write_PortAB
Expander_Set_DirectionPortA
Expander_Set_DirectionPortB
Expander_Set_DirectionPortAB
Expander_Set_PullUpsPortA
Expander_Set_PullUpsPortB
Expander_Set_PullUpsPortAB
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Expander_Init
Prototype
procedure Expander_Init(ModuleAddress : byte);
Returns
Nothing.
Initializes Port Expander using SPI communication.
Port Expander module settings :
Description -
hardware addressing enabled
automatic address pointer incrementing disabled (byte mode)
BANK_0 register adressing
slew rate enabled
Parameters :
- ModuleAddress: Port Expander hardware address, see schematic at the
bottom of this page
Global variables :
Requires
-
SPExpanderCS: Chip Select line
SPExpanderRST: Reset line
SPExpanderCS_Direction: Direction of the Chip Select pin
SPExpanderRST_Direction: Direction of the Reset pin
must be defined before using this function.
SPI module needs to be initialized. See SPI1_Init and SPI1_Init_Advanced routines.
Example
// Port Expander module connections
var SPExpanderRST : sbit at RC0_bit;
SPExpanderCS : sbit at RC1_bit;
SPExpanderRST_Direction : sbit at TRISC0_bit;
SPExpanderCS_Direction : sbit at TRISC1_bit;
// End of Port Expander module connections
...
SPI_Init();
Expander_Init(0);
// initialize SPI module
// initialize port expander
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
357
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Expander_Read_Byte
Prototype
function Expander_Read_Byte(ModuleAddress : byte; RegAddress :
byte) : byte;
Returns
Byte read.
The function reads byte from Port Expander.
Parameters :
Description
- ModuleAddress: Port Expander hardware address, see schematic at the
bottom of this page
- RegAddress: Port Expander's internal register address
Requires
Port Expander must be initialized. See Expander_Init.
Example
// Read a byte from Port Expander's register
var read_data : byte;
...
read_data := Expander_Read_Byte(0,1);
Expander_Write_Byte
Prototype
procedure Expander_Write_Byte(ModuleAddress: byte; RegAddress:
byte; Data_: byte);
Returns
Nothing.
Routine writes a byte to Port Expander.
Parameters :
Description
358
- ModuleAddress: Port Expander hardware address, see schematic at the
bottom of this page
- RegAddress: Port Expander's internal register address
- Data_: data to be written
Requires
Port Expander must be initialized. See Expander_Init.
Example
// Write a byte to the Port Expander's register
Expander_Write_Byte(0,1,0xFF);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Expander_Read_PortA
Prototype
function Expander_Read_PortA(ModuleAddress: byte): byte;
Returns
Byte read.
The function reads byte from Port Expander's PortA.
Description
Parameters :
- ModuleAddress: Port Expander hardware address, see schematic at the
bottom of this page
Port Expander must be initialized. See Expander_Init.
Requires
Example
Port Expander's PortA should be configured as input. See Expander_Set_DirectionPortA and Expander_Set_DirectionPortAB routines.
// Read a byte from Port Expander's PORTA
var read_data : byte;
...
Expander_Set_DirectionPortA(0,0xFF);
porta to be input
...
read_data := Expander_Read_PortA(0);
// set expander's
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
359
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Expander_Read_PortB
Prototype
function Expander_Read_PortB(ModuleAddress: byte): byte;
Returns
Byte read.
The function reads byte from Port Expander's PortB.
Description
Parameters :
- ModuleAddress: Port Expander hardware address, see schematic at the
bottom of this page
Port Expander must be initialized. See Expander_Init.
Requires
Example
360
Port Expander's PortB should be configured as input. See Expander_Set_DirectionPortB and Expander_Set_DirectionPortAB routines.
// Read a byte from Port Expander's PORTB
var read_data : byte;
...
Expander_Set_DirectionPortB(0,0xFF);
portb to be input
...
read_data := Expander_Read_PortB(0);
// set expander's
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Expander_Read_PortAB
Prototype
function Expander_Read_PortAB(ModuleAddress: byte): word;
Returns
Word read.
The function reads word from Port Expander's ports. PortA readings are in the
higher byte of the result. PortB readings are in the lower byte of the result.
Description Parameters :
- ModuleAddress: Port Expander hardware address, see schematic at the
bottom of this page
Port Expander must be initialized. See Expander_Init.
Requires
Example
Port Expander's PortA and PortB should be configured as inputs. See
Expander_Set_DirectionPortA, Expander_Set_DirectionPortB and
Expander_Set_DirectionPortAB routines.
// Read a byte from Port Expander's PORTA and PORTB
var read_data : word;
...
Expander_Set_DirectionPortAB(0,0xFFFF);
// set expander's
porta and portb to be input
...
read_data := Expander_Read_PortAB(0);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
361
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Expander_Write_PortA
Prototype
procedure Expander_Write_PortA(ModuleAddress: byte; Data_: byte);
Returns
Nothing.
The function writes byte to Port Expander's PortA.
Parameters :
Description
- ModuleAddress: Port Expander hardware address, see schematic at the
bottom of this page
- Data_: data to be written
Port Expander must be initialized. See Expander_Init.
Requires
Port Expander's PortA should be configured as output. See
Expander_Set_DirectionPortA and Expander_Set_DirectionPortAB routines.
// Write a byte to Port Expander's PORTA
Example
362
...
Expander_Set_DirectionPortA(0,0x00);
porta to be output
...
Expander_Write_PortA(0, 0xAA);
// set expander's
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Expander_Write_PortB
Prototype
procedure Expander_Write_PortB(ModuleAddress: byte; Data_: byte);
Returns
Nothing.
The function writes byte to Port Expander's PortB.
Parameters :
Description
- ModuleAddress: Port Expander hardware address, see schematic at the
bottom of this page
- Data_: data to be written
Port Expander must be initialized. See Expander_Init.
Requires
Port Expander's PortB should be configured as output. See
Expander_Set_DirectionPortB and Expander_Set_DirectionPortAB routines.
// Write a byte to Port Expander's PORTB
Example
...
Expander_Set_DirectionPortB(0,0x00);
portb to be output
...
Expander_Write_PortB(0, 0x55);
// set expander's
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
363
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Expander_Write_PortAB
Prototype
procedure Expander_Write_PortAB(ModuleAddress: byte; Data_: word);
Returns
Nothing.
The function writes word to Port Expander's ports.
Parameters :
Description
- ModuleAddress: Port Expander hardware address, see schematic at the
bottom of this page
- Data_: data to be written. Data to be written to PortA are passed in Data's
higher byte. Data to be written to PortB are passed in Data's lower byte
Port Expander must be initialized. See Expander_Init.
Requires
Port Expander's PortA and PortB should be configured as outputs. See
Expander_Set_DirectionPortA, Expander_Set_DirectionPortB and
Expander_Set_DirectionPortAB routines.
// Write a byte to Port Expander's PORTA and PORTB
Example
364
...
Expander_Set_DirectionPortAB(0,0x0000);
porta and portb to be output
...
Expander_Write_PortAB(0, 0xAA55);
// set expander's
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Expander_Set_DirectionPortA
Prototype
procedure Expander_Set_DirectionPortA(ModuleAddress: byte; Data_:
byte);
Returns
Nothing.
The function sets Port Expander's PortA direction.
Parameters :
Description - ModuleAddress: Port Expander hardware address, see schematic at the
bottom of this page
- Data_: data to be written to the PortA direction register. Each bit corresponds
to the appropriate pin of the PortA register. Set bit designates corresponding
pin as input. Cleared bit designates corresponding pin as output.
Requires
Port Expander must be initialized. See Expander_Init.
Example
// Set Port Expander's PORTA to be output
Expander_Set_DirectionPortA(0,0x00);
Expander_Set_DirectionPortB
Prototype
procedure Expander_Set_DirectionPortB(ModuleAddress: byte; Data_:
byte);
Returns
Nothing.
The function sets Port Expander's PortB direction.
Parameters :
Description - ModuleAddress: Port Expander hardware address, see schematic at the
bottom of this page
- Data_: data to be written to the PortB direction register. Each bit corresponds
to the appropriate pin of the PortB register. Set bit designates corresponding
pin as input. Cleared bit designates corresponding pin as output.
Requires
Port Expander must be initialized. See Expander_Init.
Example
// Set Port Expander's PORTB to be input
Expander_Set_DirectionPortB(0,0xFF);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
365
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Expander_Set_DirectionPortAB
Prototype
procedure Expander_Set_DirectionPortAB(ModuleAddress: byte;
Direction: word);
Returns
Nothing.
The function sets Port Expander's PortA and PortB direction.
Parameters :
- ModuleAddress: Port Expander hardware address, see schematic at the
bottom of this page
Description
- Direction: data to be written to direction registers. Data to be written to the
PortA direction register are passed in Direction's higher byte. Data to be
written to the PortB direction register are passed in Direction's lower byte.
Each bit corresponds to the appropriate pin of the PortA/PortB register. Set bit
designates corresponding pin as input. Cleared bit designates corresponding
pin as output.
Requires
Port Expander must be initialized. See Expander_Init.
Example
// Set Port Expander's PORTA to be output and PORTB to be input
Expander_Set_DirectionPortAB(0,0x00FF);
Expander_Set_PullUpsPortA
Prototype
procedure Expander_Set_PullUpsPortA(ModuleAddress: byte; Data_:
byte);
Returns
Nothing.
The function sets Port Expander's PortA pull up/down resistors.
Parameters :
Description - ModuleAddress: Port Expander hardware address, see schematic at the
bottom of this page
- Data_: data for choosing pull up/down resistors configuration. Each bit
corresponds to the appropriate pin of the PortA register. Set bit enables pull-up
for corresponding pin.
366
Requires
Port Expander must be initialized. See Expander_Init.
Example
// Set Port Expander's PORTA pull-up resistors
Expander_Set_PullUpsPortA(0, 0xFF);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Expander_Set_PullUpsPortB
Prototype
procedure Expander_Set_PullUpsPortB(ModuleAddress: byte; Data_:
byte);
Returns
Nothing.
The function sets Port Expander's PortB pull up/down resistors.
Parameters :
Description - ModuleAddress: Port Expander hardware address, see schematic at the
bottom of this page
- Data_: data for choosing pull up/down resistors configuration. Each bit
corresponds to the appropriate pin of the PortB register. Set bit enables
pull-up for corresponding pin.
Requires
Port Expander must be initialized. See Expander_Init.
Example
// Set Port Expander's PORTB pull-up resistors
Expander_Set_PullUpsPortB(0, 0xFF);
Expander_Set_PullUpsPortAB
Prototype
procedure Expander_Set_PullUpsPortAB(ModuleAddress: byte;
PullUps: word);
Returns
Nothing.
The function sets Port Expander's PortA and PortB pull up/down resistors.
Parameters :
Description
- ModuleAddress: Port Expander hardware address, see schematic at the
bottom of this page
- PullUps: data for choosing pull up/down resistors configuration. PortA pull
up/down resistors configuration is passed in PullUps's higher byte. PortB pull
up/down resistors configuration is passed in PullUps's lower byte. Each bit
corresponds to the appropriate pin of the PortA/PortB register. Set bit enables
pull-up for corresponding pin.
Requires
Port Expander must be initialized. See Expander_Init.
Example
// Set Port Expander's PORTA and PORTB pull-up resistors
Expander_Set_PullUpsPortAB(0, 0xFFFF);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
367
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Example
The example demonstrates how to communicate with Port Expander MCP23S17.
Note that Port Expander pins A2 A1 A0 are connected to GND so Port Expander
Hardware Address is 0.
program PortExpander;
// Port Expander module connections
var SPExpanderRST : sbit at RC0_bit;
SPExpanderCS : sbit at RC1_bit;
SPExpanderRST_Direction : sbit at TRISC0_bit;
SPExpanderCS_Direction : sbit at TRISC1_bit;
// End Port Expander module connections
var counter : byte;// = 0;
begin
counter := 0;
ANSEL := 0;
ANSELH := 0;
TRISB := 0;
PORTB := 0xFF;
// Configure AN pins as digital I/O
// Set PORTB as output
// If Port Expander Library uses SPI1 module
SPI1_Init();
// Initialize SPI module used with PortExpander
Expander_Init(0);
// Initialize Port Expander
Expander_Set_DirectionPortA(0, 0x00);
be output
// Set Expander's PORTA to
Expander_Set_DirectionPortB(0,0xFF);
be input
Expander_Set_PullUpsPortB(0,0xFF);
the Expander's PORTB pins
// Set Expander's PORTB to
while ( TRUE ) do
begin
Expander_Write_PortA(0, counter);
PORTA
Inc(counter);
PORTB := Expander_Read_PortB(0);
and write it to LEDs
Delay_ms(100);
end;
// Set pull-ups to all of
// Endless loop
// Write i to expander's
// Read expander's PORTB
end.
368
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
HW Connection
Port Expander HW connection
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
369
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
PS/2 LIBRARY
The mikroPascal PRO for PIC provides a library for communication with the common PS/2 keyboard.
Note: The library does not utilize interrupts for data retrieval, and requires the oscillator clock to be at least 6MHz.
Note: The pins to which a PS/2 keyboard is attached should be connected to the
pull-up resistors.
Note: Although PS/2 is a two-way communication bus, this library does not provide
MCU-to-keyboard communication; e.g. pressing the Caps Lock key will not turn on
the Caps Lock LED.
External dependencies of PS/2 Library
The following variables
must be defined in all
projects using PS/2
Library:
Description:
Example :
var PS2_Data : sbit;
PS/2 Data line.
sfr; external;
var PS2_Clock : sbit;
PS/2 Clock line.
sfr; external;
var PS2_Data : sbit
at RC0_bit;
var PS2_Clock : sbit
at RC1_bit;
var
PS2_Data_Direction :
sbit; sfr; external;
var
Direction of the PS/2 Data
PS2_Data_Direction :
pin.
sbit at TRISC0_bit;
var
Direction of the PS/2
PS2_Clock_Direction :
sbit; sfr; external; Clock pin.
var
PS2_Clock_Direction :
sbit at TRISC1_bit;
Library Routines
- Ps2_Config
- Ps2_Key_Read
370
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Ps2_Config
Prototype
procedure Ps2_Config();
Returns
Nothing.
Description Initializes the MCU for work with the PS/2 keyboard.
Global variables :
Requires
-
PS2_Data: Data signal line
PS2_Clock: Clock signal line
PS2_Data_Direction: Direction of the Data pin
PS2_Clock_Direction: Direction of the Clock pin
must be defined before using this function.
Example
// PS2 pinout definition
var PS2_Data : sbit at RC0_bit;
var PS2_Clock : sbit at RC1_bit;
var PS2_Data_Direction : sbit at TRISC0_bit;
var PS2_Clock_Direction : sbit at TRISC1_bit;
// End of PS2 pinout definition
...
Ps2_Config();
// Init PS/2 Keyboard
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
371
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Ps2_Key_Read
Prototype
function Ps2_Key_Read(var value: byte; var special: byte; var
pressed: byte): byte;
Returns
- 1 if reading of a key from the keyboard was successful
- 0 if no key was pressed
The function retrieves information on key pressed.
Parameters :
Description
372
- value: holds the value of the key pressed. For characters, numerals,
punctuation marks, and space value will store the appropriate ASCII code.
Routine “recognizes” the function of Shift and Caps Lock, and behaves
appropriately. For special function keys see Special Function Keys Table.
- special: is a flag for special function keys (F1, Enter, Esc, etc). If key
pressed is one of these, special will be set to 1, otherwise 0.
- pressed: is set to 1 if the key is pressed, and 0 if it is released.
Requires
PS/2 keyboard needs to be initialized. See Ps2_Config routine.
Example
var value, special, pressed: byte;
...
// Press Enter to continue:
repeat
if (Ps2_Key_Read(value, special, pressed)) then
if ((value = 13) and (special = 1)) then break;
until (0=1);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Special Function Keys
Key
Value returned
Num Lock
29
F1
1
Left Arrow
30
F2
2
Right Arrow
31
F3
3
Up Arrow
32
F4
4
Down Arrow
33
F5
5
Escape
34
F6
6
Tab
35
F7
7
F8
8
F9
9
F10
10
F11
11
F12
12
Enter
13
Page Up
14
Page Down
15
Backspace
16
Insert
17
Delete
18
Windows
19
Ctrl
20
Shift
21
Alt
22
Print Screen
23
Pause
24
Caps Lock
25
End
26
Home
27
Scroll Lock
28
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
373
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Example
This simple example reads values of the pressed keys on the PS/2 keyboard and
sends them via UART.
program PS2_Example;
var keydata, special, down : byte;
var PS2_Data
PS2_Clock
: sbit at RC0_bit;
: sbit at RC1_bit;
PS2_Data_Direction : sbit at TRISC0_bit;
PS2_Clock_Direction : sbit at TRISC1_bit;
begin
ANSEL := 0;
ANSELH := 0;
// Configure AN pins as digital I/O
keydata := 0;
special := 0;
down := 0;
UART1_Init(19200);
// Initialize UART module at 19200 bps
Ps2_Config();
// Init PS/2 Keyboard
Delay_ms(100);
// Wait for keyboard to finish
UART1_Write_Text('Ready');
while TRUE do
// Endless loop
begin
if Ps2_Key_Read(keydata, special, down) then
// If data
was read from PS/2
begin
if (down <> 0) and (keydata = 16) then // Backspace read
begin
UART1_Write(0x08); //Send Backspace to usart terminal
end
else if (down <> 0) and (keydata = 13) then // Enter read
begin
UART1_Write(10);
// Send
carriage return to usart terminal
UART1_Write(13);
// Uncomment this line
if usart terminal also expects line feed
//
for new line transition
end
else if (down <> 0) and (special = 0) and (keydata <>
0) then
// Common key read
begin
UART1_Write(keydata); // Send key to usart terminal
end;
end;
Delay_ms(1);
// Debounce period
end;
end.
374
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
HW Connection
Example of PS2 keyboard connection
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
375
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
PWM LIBRARY
CCP module is available with a number of PIC MCUs. provides library which simplifies using PWM
HW Module.
Note: Some MCUs have multiple CCP modules. In order to use the desired CCP library routine,
simply change the number 1 in the prototype with the appropriate module number, i.e.
PWM2_Start();
Library Routines
-
PWM1_Init
PWM1_Set_Duty
PWM1_Start
PWM1_Stop
PWM1_Init
Prototype
procedure PWM1_Init(freq : longint);
Returns
Nothing.
Initializes the PWM module with duty ratio 0. Parameter freq is a desired PWM
frequency in Hz (refer to device data sheet for correct values in respect with
Description Fosc).
This routine needs to be called before using other functions from PWM Library.
MCU must have CCP module.
Requires
Note: Calculation of the PWM frequency value is carried out by the compiler, as
it would produce a relatively large code if performed on the libary level.
Therefore, compiler needs to know the value of the parameter in the compile
time. That is why this parameter needs to be a constant, and not a variable.
Initialize PWM module at 5KHz:
Example
PWM1_Init(5000);
376
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
PWM1_Set_Duty
Prototype
procedure PWM1_Set_Duty(duty_ratio : byte);
Returns
Nothing.
sets PWM duty ratio. Parameter duty takes values from 0 to 255, where 0 is
Description 0%, 127 is 50%, and 255 is 100% duty ratio. Other specific values for duty ratio
can be calculated as (Percent*255)/100.
Requires
MCU must have CCP module. PWM1_Init must be called before using this routine.
Set duty ratio to 75%:
Example
PWM1_Set_Duty(192);
PWM1_Start
Prototype
procedure PWM1_Start();
Returns
Nothing.
Description Starts PWM.
Requires
MCU must have CCP module. PWM1_Init must be called before using this routine.
Example
PWM1_Start();
PWM1_Stop
Prototype
procedure PWM1_Stop();
Returns
Nothing.
Description Stops PWM.
Requires
MCU must have CCP module. PWM1_Init must be called before using this routine. PWM1_Start should be called before using this routine, otherwise it will
have no effect as the PWM module is not running.
Example
PWM1_Stop();
Library Example
The example changes PWM duty ratio on RC1 and RC2 pins continually. If LED is connected to
these pins, you can observe the gradual change of emitted light.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
377
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
program PWM_Test;
var current_duty, current_duty1, old_duty, old_duty1 : byte;
procedure InitMain();
begin
ANSEL := 0;
ANSELH := 0;
PORTA := 255;
TRISA := 255;
PORTB := 0;
TRISB := 0;
PORTC := 0;
TRISC := 0;
PWM1_Init(5000);
PWM2_Init(5000);
end;
begin
InitMain();
current_duty := 16;
current_duty1 := 16;
// Configure AN pins as digital I/O
// configure PORTA pins as input
// set PORTB to 0
// designate PORTB pins as output
// set PORTC to 0
// designate PORTC pins as output
// Initialize PWM1 module at 5KHz
// Initialize PWM2 module at 5KHz
// initial value for current_duty
// initial value for current_duty1
PWM1_Start();
PWM2_Start();
PWM1_Set_Duty(current_duty);
PWM2_Set_Duty(current_duty1);
// start PWM1
// start PWM2
// Set current duty for PWM1
// Set current duty for PWM2
while (TRUE) do
begin
if (RA0_bit <> 0) then
begin
Delay_ms(40);
Inc(current_duty);
PWM1_Set_Duty(current_duty);
end;
if (RA1_bit <> 0) then
begin
Delay_ms(40);
Dec(current_duty);
PWM1_Set_Duty(current_duty);
end;
if (RA2_bit <> 0) then
begin
Delay_ms(40);
Inc(current_duty1);
378
// endless loop
// button on RA0 pressed
// increment current_duty
// button on RA1 pressed
// decrement current_duty
// button on RA2 pressed
// increment current_duty1
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
PWM2_Set_Duty(current_duty1);
end;
if (RA3_bit <> 0) then
// button on RA3 pressed
begin
Delay_ms(40);
Dec(current_duty1);
// decrement current_duty1
PWM2_Set_Duty(current_duty1);
end;
Delay_ms(5);
end;
// slow down change pace a little
end.
HW Connection
PWM demonstration
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
379
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
RS-485 LIBRARY
RS-485 is a multipoint communication which allows multiple devices to be connected to a single bus. The mikroPascal PRO for PIC provides a set of library routines
for comfortable work with RS485 system using Master/Slave architecture. Master
and Slave devices interchange packets of information. Each of these packets contains synchronization bytes, CRC byte, address byte and the data. Each Slave has
unique address and receives only packets addressed to it. The Slave can never initiate communication.
It is the user’s responsibility to ensure that only one device transmits via 485 bus at
a time.
The RS-485 routines require the UART module. Pins of UART need to be attached
to RS-485 interface transceiver, such as LTC485 or similar (see schematic at the
bottom of this page).
Note: The library uses the UART module for communication. The user must initialize the appropriate UART module before using the RS-485 Library. For MCUs with
two UART modules it is possible to initialize both of them and then switch by using
the UART_Set_Active function. See the UART Library functions.
Library constants:
- START byte value = 150
- STOP byte value = 169
- Address 50 is the broadcast address for all Slaves (packets containing address 50
will be received by all Slaves except the Slaves with addresses 150 and 169).
External dependencies of RS-485 Library
The following variable
must be defined in all
projects using RS-485
Library:
var RS485_rxtx_pin :
sbit; sfr; external;
Description:
Control RS-485 Transmit/Receive operation
mode
var
RS485_rxtx_pin_direc- Direction of the RS-485
tion : sbit; sfr;
Transmit/Receive pin
external;
380
Example :
var RS485_rxtx_pin :
sbit at RC2_bit;
var
RS485_rxtx_pin_direction : sbit at
TRISC2_bit;
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Routines
-
RS485Master_Init
RS485Master_Receive
RS485Master_Send
RS485Slave_Init
RS485Slave_Receive
RS485Slave_Send
RS485Master_Init
Prototype
procedure RS485Master_Init();
Returns
Nothing.
Description Initializes MCU as a Master for RS-485 communication.
Global variables :
- RS485_rxtx_pin - this pin is connected to RE/DE input of RS-485
transceiver(see schematic at the bottom of this page). RE/DE signal controls
RS-485 transceiver operation mode.
Requires
- RS485_rxtx_pin_direction - direction of the RS-485 Transmit/Receive pin
must be defined before using this function.
UART HW module needs to be initialized. See UARTx_Init.
Example
// RS485 module pinout
var RS485_rxtx_pin : sbit at RC2_bit;
var RS485_rxtx_pin_direction : sbit at TRISC2_bit;
// End of RS485 module pinout
...
UART1_Init(9600);
// initialize UART module
RS485Master_Init();
// intialize MCU as a
Master for RS-485 communication
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
381
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
RS485Master_Receive
Prototype
procedure RS485Master_Receive(var data_buffer: array[5] of byte);
Returns
Nothing.
Receives messages from Slaves. Messages are multi-byte, so this routine must
be called for each byte received.
Parameters :
Description
-
data_buffer: 7 byte buffer for storing received data, in the following manner:
data[0..2]: message content
data[3]: number of message bytes received, 1–3
data[4]: is set to 255 when message is received
data[5]: is set to 255 if error has occurred
data[6]: address of the Slave which sent the message
The function automatically adjusts data[4] and data[5] upon every received
message. These flags need to be cleared by software.
382
Requires
MCU must be initialized as a Master for RS-485 communication. See
RS485Master_Init.
Example
var msg : array[20] of byte;
...
RS485Master_Receive(msg);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
RS485Master_Send
Prototype
procedure RS485Master_Send(var data_buffer: array[20] of byte;
datalen: byte; slave_address: byte);
Returns
Nothing.
Sends message to Slave(s). Message format can be found at the bottom of this
page.
Description
Parameters :
- data_buffer: data to be sent
- datalen: number of bytes for transmition. Valid values: 0...3.
- slave_address: Slave(s) address
MCU must be initialized as a Master for RS-485 communication. See
RS485Master_Init.
Requires
It is the user’s responsibility to ensure (by protocol) that only one device sends
data via 485 bus at a time.
Example
var msg : array[20] of byte;
...
// send 3 bytes of data to Slave with address 0x12
RS485Master_Send(msg, 3, 0x12);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
383
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
RS485Slave_Init
Prototype
procedure RS485Slave_Init(slave_address: byte);
Returns
Nothing.
Initializes MCU as a Slave for RS-485 communication.
Description Parameters :
- slave_address: Slave address
Global variables :
Requires
- RS485_rxtx_pin - this pin is connected to RE/DE input of RS-485
transceiver(see schematic at the bottom of this page). RE/DE signal controls
RS-485 transceiver operation mode. Valid values: 1 (for transmitting) and 0
(for receiving)
- RS485_rxtx_pin_direction - direction of the RS-485 Transmit/Receive pin
must be defined before using this function.
UART HW module needs to be initialized. See UARTx_Init.
Example
384
// RS485 module pinout
var RS485_rxtx_pin : sbit at RC2_bit;
var RS485_rxtx_pin_direction : sbit at TRISC2_bit;
// End of RS485 module pinout
...
UART1_Init(9600);
// initialize UART module
RS485Slave_Init(160);
// intialize MCU as a
Slave for RS-485 communication with address 160
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
RS485slave_Receive
Prototype
procedure RS485Slave_Receive(var data_buffer: array[20] of byte);
Returns
Nothing.
Receives messages from Master. If Slave address and Message address field
don't match then the message will be discarded. Messages are multi-byte, so
this routine must be called for each byte received.
Parameters :
data_buffer: 6 byte buffer for storing received data, in the following manner:
Description
-
data[0..2]: message content
data[3]: number of message bytes received, 1–3
data[4]: is set to 255 when message is received
data[5]: is set to 255 if error has occurred
The function automatically adjusts data[4] and data[5] upon every received message. These flags need to be cleared by software.
Requires
MCU must be initialized as a Slave for RS-485 communication. See
RS485Slave_Init.
Example
var msg : array[20] of byte;
...
RS485Slave_Read(msg);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
385
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
RS485Slave_Send
Prototype
procedure RS485Slave_Send(var data_buffer: array[20] of byte;
datalen : byte);
Returns
Nothing.
Sends message to Master. Message format can be found at the bottom of this
page.
Description Parameters :
- data_buffer: data to be sent
- datalen: number of bytes for transmition. Valid values: 0...3.
Requires
MCU must be initialized as a Slave for RS-485 communication. See
RS485Slave_Init. It is the user’s responsibility to ensure (by protocol) that only
one device sends data via 485 bus at a time.
Example
var msg : array[8] of byte;
...
// send 2 bytes of data to the Master
RS485Slave_Send(msg, 2);
Library Example
This is a simple demonstration of RS485 Library routines usage.
Master sends message to Slave with address 160 and waits for a response. The Slave accepts
data, increments it and sends it back to the Master. Master then does the same and sends incremented data back to Slave, etc.
Master displays received data on PORTB, while error on receive (0xAA) and number of consecutive unsuccessful retries are displayed on PORTD. Slave displays received data on PORTB,
while error on receive (0xAA) is displayed on PORTD. Hardware configurations in this example
are made for the EasyPIC5 board and 16F887.
RS485 Master code:
program RS485_Master_Example;
var dat : array[10] of byte ;
ing messages
i, j : byte;
cnt : longint;
386
// buffer for receving/send-
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
var rs485_rxtx_pin : sbit at RC2_bit;
// set transcieve pin
rs485_rxtx_pin_direction : sbit at TRISC2_bit;
// set transcieve pin direction
// Interrupt routine
procedure interrupt(); org 0x16;
begin
RS485Master_Receive(dat);
end;
begin
cnt := 0;
ANSEL := 0;
ANSELH := 0;
PORTB
PORTD
TRISB
TRISD
:=
:=
:=
:=
// Configure AN pins as digital I/O
0;
0;
0;
0;
UART1_Init(9600);
Delay_ms(100);
// initialize UART1 module
RS485Master_Init();
dat[0] := 0xAA;
dat[1] := 0xF0;
dat[2] := 0x0F;
dat[4] := 0;
dat[5] := 0;
dat[6] := 0;
// initialize MCU as Master
// ensure that message received flag is 0
// ensure that error flag is 0
RS485Master_Send(dat,1,160);
PIE1.RCIE := 1;
PIE2.TXIE := 0;
INTCON.PEIE := 1;
INTCON.GIE := 1;
while (TRUE) do
begin
//
//
//
//
enable interrupt on UART1 receive
disable interrupt on UART1 transmit
enable peripheral interrupts
enable all interrupts
// upon completed valid message receiving
//
data[4] is set to 255
Inc(cnt);
if (dat[5] <> 0) then
PORTD := 0xAA;
if (dat[4] <> 0) then
begin
// if an error detected, signal it
//
by setting portd to 0xAA
// if message received successfully
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
387
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
cnt := 0;
dat[4] := 0;
// clear message received flag
j := dat[3];
for i := 1 to dat[3] do
// show data on PORTB
PORTB := dat[i-1];
dat[0] := dat[0]+1;
// send back to master
Delay_ms(1);
RS485Master_Send(dat,1,160);
end;
if (cnt > 100000) then // if in 100000 poll-cycles the answer
begin
Inc(PORTD);
//
was not detected, signal
cnt := 0;
//
failure of send-message
RS485Master_Send(dat,1,160);
if (PORTD > 10) then
// if sending failed 10 times
begin
RS485Master_Send(dat,1,50);
//
send message on
broadcast address
end;
end;
end;
//
function to be properly linked.
end.
RS485 Slave code:
program RS485_Slave_Example;
var dat : array[20] of byte;
ing messages
i, j : byte;
// buffer for receving/send-
var rs485_rxtx_pin : sbit at RC2_bit;
// set transcieve pin
rs485_rxtx_pin_direction : sbit at TRISC2_bit;
// set transcieve pin direction
// Interrupt routine
procedure interrupt();
begin
RS485Slave_Receive(dat);
end;
begin
ANSEL := 0;
ANSELH := 0;
388
// Configure AN pins as digital I/O
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
PORTB
PORTD
TRISB
TRISD
Libraries
:=
:=
:=
:=
0;
0;
0;
0;
UART1_Init(9600);
Delay_ms(100);
RS485Slave_Init(160);
// initialize UART1 module
// Intialize MCU as slave, address 160
dat[4] := 0;
dat[5] := 0;
dat[6] := 0;
// ensure that message received flag is 0
// ensure that message received flag is 0
// ensure that error flag is 0
PIE1.RCIE := 1;
PIE2.TXIE := 0;
INTCON.PEIE := 1;
INTCON.GIE := 1;
//
//
//
//
enable interrupt on UART1 receive
disable interrupt on UART1 transmit
enable peripheral interrupts
enable all interrupts
while (TRUE) do
begin
if (dat[5] <> 0) then // if an error detected, signal it by
begin
PORTD := 0xAA;
//
setting portd to 0xAA
dat[5] := 0;
end;
if (dat[4] <> 0) then // upon completed valid message receive
begin
dat[4] := 0;
//
data[4] is set to 0xFF
j := dat[3];
for i := 1 to dat[3] do
PORTB := dat[i-1];
dat[0] := dat[0]+1;
Delay_ms(1);
RS485Slave_Send(dat,1);
end;
// show data on PORTB
// increment received dat[0]
// and send it back to master
end;
end.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
389
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
HW Connection
Example of interfacing PC to PIC MCU via RS485 bus with LTC485 as RS-485
transceiver
390
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Message format and CRC calculations
Q: How is CRC checksum calculated on RS485 master side?
START_BYTE := 0x96; // 10010110
STOP_BYTE := 0xA9; // 10101001
PACKAGE:
-------START_BYTE 0x96
ADDRESS
DATALEN
[DATA1]
[DATA2]
[DATA3]
CRC
STOP_BYTE 0xA9
// if exists
// if exists
// if exists
DATALEN bits
-----------bit7 := 1 MASTER SENDS
0 SLAVE SENDS
bit6 := 1 ADDRESS WAS XORed with 1, IT WAS EQUAL
STOP_BYTE
0 ADDRESS UNCHANGED
bit5 := 0 FIXED
bit4 := 1
DATA3 (if exists) WAS XORed with 1,
START_BYTE or STOP_BYTE
0 DATA3 (if exists) UNCHANGED
bit3 := 1
DATA2 (if exists) WAS XORed with 1,
START_BYTE or STOP_BYTE
0 DATA2 (if exists) UNCHANGED
bit2 := 1
DATA1 (if exists) WAS XORed with 1,
START_BYTE or STOP_BYTE
0 DATA1 (if exists) UNCHANGED
bit1bit0 := 0 to 3 NUMBER OF DATA BYTES SEND
CRC generation :
---------------crc_send := datalen xor address;
crc_send := crc_send xor data[0];
// if
crc_send := crc_send xor data[1];
// if
crc_send := crc_send xor data[2];
// if
crc_send := not crc_send;
if ((crc_send = START_BYTE) or (crc_send =
Inc(crc_send);
NOTE:
DATALEN<4..0>
can
STOP_BYTE<4..0> values.
not
take
TO START_BYTE or
IT WAS EQUAL TO
IT WAS EQUAL TO
IT WAS EQUAL TO
exists
exists
exists
STOP_BYTE)) then
the
START_BYTE<4..0>
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
or
391
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SOFTWARE I²C LIBRARY
The mikroPascal PRO for PIC provides routines for implementing Software I2C
communication. These routines are hardware independent and can be used with
any MCU. The Software I2C library enables you to use MCU as Master in I2C communication. Multi-master mode is not supported.
Note: This library implements time-based activities, so interrupts need to be disabled when using Software I2C.
Note: All Software I2C Library functions are blocking-call functions (they are waiting
for I2C clock line to become logical one).
Note: The pins used for the Software I2C communication should be connected to
the pull-up resistors. Turning off the LEDs connected to these pins may also be
required.
External dependencies of Software I²C Library
The following variables
must be defined in all
projects using Software
I2C Library:
var Soft_I2C_Scl :
sbit; sfr; external;
var Soft_I2C_Sda :
sbit; sfr; external;
Description:
Soft I2C Clock line.
Soft I2C Data line.
Example :
var Soft_I2C_Scl :
sbit at RC3_bit;
var Soft_I2C_Sda :
sbit at RC4_bit;
var
Soft_I2C_Scl_Directio Direction of the Soft I2C
n : sbit; sfr;
Clock pin.
external;
var
Soft_I2C_Scl_Directio
n : sbit at
TRISC3_bit;
var
Soft_I2C_Sda_Directio Direction of the Soft I2C
n : sbit; sfr;
Data pin.
external;
var
Soft_I2C_Sda_Directio
n : sbit at
TRISC4_bit;
Library Routines
-
392
Soft_I2C_Init
Soft_I2C_Start
Soft_I2C_Read
Soft_I2C_Write
Soft_I2C_Stop
Soft_I2C_Break
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Soft_I2C_Init
Prototype
procedure Soft_I2C_Init();
Returns
Nothing.
Description Configures the software I2C module.
Global variables :
Requires
- Soft_I2C_Scl: Soft I2C clock line
- Soft_I2C_Sda: Soft I2C data line
- Soft_I2C_Scl_Direction: Direction of the Soft I2C clock pin
- Soft_I2C_Sda_Direction: Direction of the Soft I2C data pin
must be defined before using this function.
Example
// Soft_I2C pinout definition
var Soft_I2C_Scl
: sbit at RC3_bit;
var Soft_I2C_Sda
: sbit at RC4_bit;
var Soft_I2C_Scl_Direction : sbit at TRISC3_bit;
var Soft_I2C_Sda_Direction : sbit at TRISC4_bit;
// End of Soft_I2C pinout definition
...
Soft_I2C_Init();
Soft_I2C_Start
Prototype
procedure Soft_I2C_Start();
Returns
Nothing.
Description Determines if the I2C bus is free and issues START signal.
Requires
Software I2C must be configured before using this function. See Soft_I2C_Init
routine.
Example
// Issue START signal
Soft_I2C_Start();
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
393
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Soft_I2C_Read
Prototype
function Soft_I2C_Read(ack: word): byte;
Returns
One byte from the Slave.
Reads one byte from the slave.
Description
Parameters :
- ack: acknowledge signal parameter. If the ack==0 not acknowledge signal will
be sent after reading, otherwise the acknowledge signal will be sent.
Soft I2C must be configured before using this function. See Soft_I2C_Init routine.
Requires
Example
Also, START signal needs to be issued in order to use this function. See
Soft_I2C_Start routine.
var take : word;
...
// Read data and send the not_acknowledge signal
take := Soft_I2C_Read(0);
Soft_I2C_Write
Prototype
function Soft_I2C_Write(_data: byte): byte;
Returns
- 0 if there were no errors.
- 1 if write collision was detected on the I˛C bus.
Sends data byte via the I˛C bus.
Description Parameters :
- _Data: data to be sent
Soft I2C must be configured before using this function. See Soft_I2C_Init routine.
Requires
Example
394
Also, START signal needs to be issued in order to use this function. See
Soft_I2C_Start routine.
var _data, error : byte;
...
error := Soft_I2C_Write(data);
error := Soft_I2C_Write(0xA3);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Soft_I2C_Stop
Prototype
procedure Soft_I2C_Stop();
Returns
Nothing.
Description Issues STOP signal.
Requires
Soft I2C must be configured before using this function. See Soft_I2C_Init routine.
Example
// Issue STOP signal
Soft_I2C_Stop();
Soft_I2C_Break
Prototype
procedure Soft_I2C_Break();
Returns
Nothing.
All Software I2C Library functions can block the program flow (see note at the
top of this page). Calling this routine from interrupt will unblock the program
Description execution. This mechanism is similar to WDT.
Note: Interrupts should be disabled before using Software I2C routines again
(see note at the top of this page).
Requires
Nothing.
var data1, error, counter : byte;
Example
procedure interrupt();
begin
if (INTCON.T0IF <> 0) then
if (counter >= 20) then
begin
Soft_I2C_Break();
counter := 0;
end
else
Inc(counter);
INTCON.T0IF := 0;
rupt flag
end;
begin
counter := 0;
OPTION_REG := 0x04;
// reset counter
// increment counter
// Clear Timer0 overflow inter-
// TMR0 prescaler set to 1:32
...
// try Soft_I2C_Init with blocking prevention mechanism
INTCON.GIE := 1;
// Global interrupt enable
INTCON.T0IE := 1;
// Enable Timer0 overflow interrupt
Soft_I2C_Init();
INTCON.GIE := 0;
// Global interrupt disable
end.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
395
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Example
The example demonstrates Software I˛C Library routines usage. The PIC MCU is
connected (SCL, SDA pins) to PCF8583 RTC (real-time clock). Program reads date
and time are read from the RTC and prints it on Lcd.
program RTC_Read;
var seconds, minutes, hours, day, month, year : byte;
date/time variables
// Global
// Software I2C connections
var Soft_I2C_Scl
: sbit at RC3_bit;
Soft_I2C_Sda
: sbit at RC4_bit;
Soft_I2C_Scl_Direction : sbit at TRISC3_bit;
Soft_I2C_Sda_Direction : sbit at TRISC4_bit;
// End Software I2C connections
// LCD module connections
var LCD_RS : sbit at RB4_bit;
LCD_EN : sbit at RB5_bit;
LCD_D4 : sbit at RB0_bit;
LCD_D5 : sbit at RB1_bit;
LCD_D6 : sbit at RB2_bit;
LCD_D7 : sbit at RB3_bit;
LCD_RS_Direction : sbit at
LCD_EN_Direction : sbit at
LCD_D4_Direction : sbit at
LCD_D5_Direction : sbit at
LCD_D6_Direction : sbit at
LCD_D7_Direction : sbit at
// End LCD module connections
TRISB4_bit;
TRISB5_bit;
TRISB0_bit;
TRISB1_bit;
TRISB2_bit;
TRISB3_bit;
//--------------------- Reads time and date information from RTC
(PCF8583)
procedure Read_Time();
begin
Soft_I2C_Start();
// Issue start signal
Soft_I2C_Write(0xA0); // Address PCF8583, see PCF8583 datasheet
Soft_I2C_Write(2);
// Start from address 2
Soft_I2C_Start();
// Issue repeated start signal
Soft_I2C_Write(0xA1); // Address PCF8583 for reading R/W=1
seconds := Soft_I2C_Read(1);
// Read seconds byte
minutes := Soft_I2C_Read(1);
// Read minutes byte
hours := Soft_I2C_Read(1);
// Read hours byte
day := Soft_I2C_Read(1);
// Read year/day byte
month := Soft_I2C_Read(0);
// Read weekday/month byte}
Soft_I2C_Stop();
end;
396
// Issue stop signal}
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
//-------------------- Formats date and time
procedure Transform_Time() ;
begin
seconds := ((seconds and 0xF0) shr 4)*10 +
// Transform seconds
minutes := ((minutes and 0xF0) shr 4)*10 +
// Transform months
hours
:= ((hours and 0xF0) shr 4)*10
// Transform hours
year
:=
(day and 0xC0) shr 6;
day
:=
((day and 0x30) shr 4)*10
// Transform day
month
:= ((month and 0x10) shr 4)*10
// Transform month
end;
(seconds and 0x0F);
(minutes and 0x0F);
+ (hours and 0x0F);
// Transform year
+ (day and 0x0F);
+ (month and 0x0F);
//-------------------- Output values to LCD
procedure Display_Time();
begin
Lcd_Chr(1, 6, (day / 10)
+ 48);
// Print tens digit of day
variable
Lcd_Chr(1, 7, (day mod 10)
+ 48); // Print oness digit of
day variable
Lcd_Chr(1, 9, (month / 10) + 48);
Lcd_Chr(1,10, (month mod 10) + 48);
Lcd_Chr(1,15, year
+ 56);
// Print year vaiable +
8 (start from year 2008)
Lcd_Chr(2, 6,
Lcd_Chr(2, 7,
Lcd_Chr(2, 9,
Lcd_Chr(2,10,
Lcd_Chr(2,12,
Lcd_Chr(2,13,
end;
(hours / 10)
+
(hours mod 10)
(minutes / 10) +
(minutes mod 10)
(seconds / 10) +
(seconds mod 10)
48);
+ 48);
48);
+ 48);
48);
+ 48);
//------------------ Performs project-wide init
procedure Init_Main();
begin
TRISB := 0;
PORTB := 0xFF;
TRISB := 0xff;
ANSEL := 0;
ANSELH := 0;
Soft_I2C_Init();
// Configure AN pins as digital I/O
// Initialize Soft I2C communication
Lcd_Init();
Lcd_Cmd(_LCD_CLEAR);
Lcd_Cmd(_LCD_CURSOR_OFF);
// Initialize LCD
// Clear LCD display
// Turn cursor off
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
397
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
LCD_Out(1,1,'Date:');
LCD_Chr(1,8,':');
LCD_Chr(1,11,':');
LCD_Out(2,1,'Time:');
LCD_Chr(2,8,':');
LCD_Chr(2,11,':');
LCD_Out(1,12,'200');
end;
// Prepare and output static text on LCD
//----------------- Main procedure
begin
Delay_ms(1000);
Init_Main();
while TRUE do
begin
Read_Time();
Transform_Time();
Display_Time();
end;
end.
398
// Perform initialization
// Endless loop
// Read time from RTC(PCF8583)
// Format date and time
// Prepare and display on LCD
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SOFTWARE SPI LIBRARY
The mikroPacal PRO for PIC provides routines for implementing Software SPI communication. These routines are hardware independent and can be used with any
MCU. The Software SPI Library provides easy communication with other devices via
SPI: A/D converters, D/A converters, MAX7219, LTC1290, etc.
Library configuration:
-
SPI to Master mode
Clock value = 20 kHz.
Data sampled at the middle of interval.
Clock idle state low.
Data sampled at the middle of interval.
Data transmitted at low to high edge.
Note: The Software SPI library implements time-based activities, so interrupts need
to be disabled when using it.
External dependencies of Software SPI Library
The following variables
must be defined in all
projects using Software
SPI Library:
var SoftSpi_SDI :
sbit; sfr; external;
var SoftSpi_SDO :
sbit; sfr; external;
var SoftSpi_CLK :
sbit; sfr; external;
Description:
Data In line.
Data Out line.
Clock line.
Example :
var SoftSpi_SDI :
sbit at RC4_bit;
var SoftSpi_SDO :
sbit at RC5_bit;
var SoftSpi_CLK :
sbit at RC3_bit;
var
Direction of the Data In
SoftSpi_SDI_Direction
: sbit; sfr; external; pin.
var
SoftSpi_SDI_Direction
: sbit at TRISC4_bit;
var
Direction of the Data Out
SoftSpi_SDO_Direction
: sbit; sfr; external; pin
var
SoftSpi_SDO_Direction
: sbit at TRISC5_bit;
var
SoftSpi_CLK_Direction Direction of the Clock pin.
: sbit; sfr; external;
var
SoftSpi_CLK_Direction
: sbit at TRISC3_bit;
Library Routines
- Soft_SPI_Init
- Soft_SPI_Read
- Soft_SPI_Write
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
399
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Soft_SPI_Init
Prototype
procedure Soft_SPI_Init();
Returns
Nothing.
Description Configures and initializes the software SPI module.
Global variables:
Requires
-
Chip_Select: Chip select line
SoftSpi_SDI: Data in line
SoftSpi_SDO: Data out line
SoftSpi_CLK: Data clock line
Chip_Select_Direction: Direction
SoftSpi_SDI_Direction: Direction
SoftSpi_SDO_Direction: Direction
SoftSpi_CLK_Direction: Direction
of
of
of
of
the
the
the
the
Chip select pin
Data in pin
Data out pin
Data clock pin
must be defined before using this function.
// Software SPI
var Chip_Select
var SoftSpi_SDI
var SoftSpi_SDO
var SoftSpi_CLK
Example
400
module
: sbit
: sbit
: sbit
: sbit
connections
at RC1;
at RC4_bit;
at RC5_bit;
at RC3_bit;
var Chip_Select_Direction : sbit at TRISC1_bit;
var SoftSpi_SDI_Direction : sbit at TRISC4_bit;
var SoftSpi_SDO_Direction : sbit at TRISC5_bit;
var SoftSpi_CLK_Direction : sbit at TRISC3_bit;
// End Software SPI module connections
...
Soft_SPI_Init(); // Init Soft_SPI
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Soft_SPI_Read
Prototype
function Soft_SPI_Read(sdata: byte): word;
Returns
Byte received via the SPI bus.
This routine performs 3 operations simultaneously. It provides clock for the Software SPI bus, reads a byte and sends a byte.
Description
Parameters :
- sdata: data to be sent.
Requires
Soft SPI must be initialized before using this function. See Soft_SPI_Init routine.
Example
var data_read : word;
data_send : byte;
...
// Read a byte and assign it to data_read variable
// (data_send byte will be sent via SPI during the Read operation)
data_read := Soft_SPI_Read(data_send);
Soft_SPI_Write
Prototype
procedure Soft_SPI_Write(sdata: byte);
Returns
Nothing.
This routine sends one byte via the Software SPI bus.
Description Parameters :
- sdata: data to be sent.
Requires
Soft SPI must be initialized before using this function. See Soft_SPI_Init routine.
Example
// Write a byte to the Soft SPI bus
Soft_SPI_Write(0xAA);
Library Example
This code demonstrates using library routines for Soft_SPI communication. Also, this example
demonstrates working with Microchip's MCP4921 12-bit D/A converter.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
401
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
program Soft_SPI;
// DAC module connections
var Chip_Select : sbit at
SoftSpi_CLK : sbit at
SoftSpi_SDI : sbit at
SoftSpi_SDO : sbit at
RC1_bit;
RC3_bit;
RC4_bit;
RC5_bit;
var Chip_Select_Direction : sbit
SoftSpi_CLK_Direction : sbit
SoftSpi_SDI_Direction : sbit
SoftSpi_SDO_Direction : sbit
// End DAC module connections
at
at
at
at
// Note: Input signal
TRISC1_bit;
TRISC3_bit;
TRISC4_bit;
TRISC5_bit;
var value : word;
procedure InitMain();
begin
TRISA0_bit := 1;
TRISA1_bit := 1;
Chip_Select := 1;
Chip_Select_Direction := 0;
Soft_Spi_Init();
end;
// Set RA0 pin as input
// Set RA1 pin as input
// Deselect DAC
// Set CS# pin as Output
// Initialize Soft_SPI
// DAC increments (0..4095) --> output voltage (0..Vref)
procedure DAC_Output( valueDAC : word);
var temp : byte; volatile;
begin
Chip_Select := 0;
// Select DAC chip
// Send High Byte
temp := word(valueDAC shr 8) and 0x0F;
// Store valueDAC[11..8]
to temp[3..0]
temp := temp or 0x30; // Define DAC setting, see MCP4921 datasheet
Soft_SPI_Write(temp);
// Send high byte via Soft SPI
// Send Low Byte
temp := valueDAC;
Soft_SPI_Write(temp);
Chip_Select := 1;
end;
// Store valueDAC[7..0] to temp[7..0]
// Send low byte via Soft SPI
// Deselect DAC chip
begin
ANSEL := 0;
ANSELH := 0;
C1ON_bit := 0;
C2ON_bit := 0;
402
// Disable comparators
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
InitMain();
value := 2048;
while (TRUE) do
begin
Libraries
// Perform main initialization
// When program starts, DAC gives
//
the output in the mid-range
// Endless loop
if ((RA0_bit) and (value < 4095)) then
// If PA0 button
is pressed
Inc(value)
//
increment value
else
begin
if ((RA1_bit) and (value > 0)) then // If PA1 button
is pressed
Dec(value);
//
decrement value
end;
DAC_Output(value);
Delay_ms(1);
end;
// Send value to DAC chip
// Slow down key repeat pace
end.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
403
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SOFTWARE UART LIBRARY
The mikroPascal PRO for PIC provides routines for implementing Software UART
communication. These routines are hardware independent and can be used with
any MCU. The Software UART Library provides easy communication with other
devices via the RS232 protocol.
Note: The Software UART library implements time-based activities, so interrupts
need to be disabled when using it.
Library Routines
-
404
Soft_UART_Init
Soft_UART_Read
Soft_UART_Write
Soft_UART_Break
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Soft_UART_Init
Prototype
function Soft_Uart_Init(var port : byte; rx_pin, tx_pin,
baud_rate : dword, inverted : byte): byte;
Returns
- 2 - error, requested baud rate is too low
- 1 - error, requested baud rate is too high
- 0 - successfull initialization
Configures and initializes the software UART module.
Parameters :
-
Description
port: port to be used.
rx_pin: sets rx_pin to be used.
tx_pin: sets tx_pin to be used.
baud_rate: baud rate to be set. Maximum baud rate depends on the MCU’s -
clock and working conditions.
- inverted: inverted output flag. When set to a non-zero value, inverted logic
on output is used.
Software UART routines use Delay_Cyc routine. If requested baud rate is too
low then calculated parameter for calling Delay_Cyc exceeeds Delay_Cyc argument range.
If requested baud rate is too high then rounding error of Delay_Cyc argument
corrupts Software UART timings.
Requires
Nothing.
Example
var error : byte;
...
// Initialize Software UART communication on pins Rx, Tx, at 9600 bps
error := Soft_UART_Init(PORTC, 7, 6, 14400, 0);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
405
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Soft_UART_Read
Prototype
function Soft_UART_Read(var error: byte): byte;
Returns
Byte received via UART.
The function receives a byte via software UART.
This is a blocking function call (waits for start bit). Programmer can unblock it by
calling Soft_UART_Break routine.
Description Parameters :
- error: Error flag. Error code is returned through this variable.
0 - no error
1 - stop bit error
255 - user abort, Soft_UART_Break called
Requires
Example
Software UART must be initialized before using this function. See the
Soft_UART_Init routine.
var data : byte;
error : byte;
...
// wait until data is received
repeat
data := Soft_UART_Read(error);
until (error=0);
// Now we can work with data:
if ( data ) then
begin
...
end
406
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Soft_UART_Write
Prototype
procedure Soft_UART_Write(udata: byte);
Returns
Nothing.
This routine sends one byte via the Software UART bus.
Description Parameters :
- udata: data to be sent.
Software UART must be initialized before using this function. See the
Soft_UART_Init routine.
Requires
Be aware that during transmission, software UART is incapable of receiving data –
data transfer protocol must be set in such a way to prevent loss of information.
Example
var some_byte : byte;
...
// Write a byte via Soft UART
some_byte := 0x0A;
Soft_UART_Write(some_byte);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
407
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Soft_UART_Break
Prototype
procedure Soft_UART_Break();
Returns
Nothing.
Description
Soft_UART_Read is blocking routine and it can block the program flow. Call this
routine from interrupt to unblock the program execution. This mechanism is similar to WDT.
Note: Interrupts should be disabled before using Software UART routines again
(see note at the top of this page).
Requires
Nothing.
var data1, error, counter : byte;
procedure interrupt();
begin
if (INTCON.T0IF <> 0) then
if (counter >= 20) then
begin
Soft_UART_Break();
counter := 0;
end
else
Inc(counter);
INTCON.T0IF := 0;
rupt flag
end;
Example
begin
counter := 0;
OPTION_REG := 0x04;
// reset counter
// increment counter
// Clear Timer0 overflow inter-
// TMR0 prescaler set to 1:32
...
if (Soft_UART_Init(PORTC, 7, 6, 9600, 0) = 0) then
Soft_UART_Write(0x55);
...
// try Soft_UART_Read with blocking prevention mechanism
INTCON.GIE := 1;
// Global interrupt enable
INTCON.T0IE := 1;
// Enable Timer0 overflow interrupt
data1 := Soft_UART_Read(error);
INTCON.GIE := 0;
// Global interrupt disable
end.
408
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Example
This example demonstrates simple data exchange via software UART. If MCU is
connected to the PC, you can test the example from the mikroPascal PRO for PIC
USART Terminal Tool.
program Soft_UART;
var error : byte;
counter, byte_read : byte;
// Auxiliary variables
begin
ANSEL := 0;
ANSELH := 0;
TRISB := 0x00;
PORTB := 0;
// Configure AN pins as digital I/O
// Set PORTB as output (error signalization)
// No error
error := Soft_UART_Init(PORTC, 7, 6, 14400, 0); // Initialize Soft
UART at 14400 bps
if (error > 0) then
begin
PORTB := error;
// Signalize Init error
while (TRUE) do nop;
// Stop program
end;
Delay_ms(100);
for counter := 'z' downto 'A' do
downto 'A'
begin
Soft_UART_Write(counter);
Delay_ms(100);
end;
// Send bytes from 'z'
while TRUE do
// Endless loop
begin
byte_read := Soft_UART_Read(error); // Read byte, then test
error flag
if (error <> 0) then
// If error was detected
PORTB := error
//
signal it on PORTB
else
Soft_UART_Write(byte_read);
// If error was not detected, return byte read
end;
end.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
409
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SOUND LIBRARY
The mikroPascal PRO for PIC provides a Sound Library to supply users with routines necessary
for sound signalization in their applications. Sound generation needs additional hardware, such
as piezo-speaker (example of piezo-speaker interface is given on the schematic at the bottom of
this page).
Library Routines
- Sound_Init
- Sound_Play
Sound_Init
Prototype
procedure Sound_Init(var snd_port : byte; snd_pin : byte);
Returns
Nothing.
Configures the appropriate MCU pin for sound generation.
Description
Parameters :
- snd_port: sound output port address
- snd_pin: sound output pin
410
Requires
Nothing.
Example
Sound_Init(PORTD, 3);
// Initialize sound at RD3
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Sound_Play
Prototype
procedure Sound_Play(freq_in_hz, duration_ms : word);
Returns
Nothing.
Generates the square wave signal on the appropriate pin.
Parameters :
- freq_in_hz: signal frequency in Hertz (Hz)
Description - duration_ms: signal duration in miliseconds (ms)
Note: frequency range is limited by Delay_Cyc parameter. Maximum frequency
that can be produced by this function is Freq_max = Fosc/(80*3). Minimum
frequency is Freq_min = Fosc/(80*255). Generated frequency may differ
from the freq_in_hz parameter due to integer arithmetics.
Requires
In order to hear the sound, you need a piezo speaker (or other hardware) on
designated port. Also, you must call Sound_Init to prepare hardware for output
before using this function.
Example
// Play sound of 1KHz in duration of 100ms
Sound_Play(1000, 100);
Library Example
The example is a simple demonstration of how to use the Sound Library for playing tones on a
piezo speaker.
program Sound;
procedure Tone1();
begin
Sound_Play(659, 250);
end;
procedure Tone2();
begin
Sound_Play(698, 250);
end;
procedure Tone3();
begin
Sound_Play(784, 250);
end;
// Frequency = 659Hz, duration = 250ms
// Frequency = 698Hz, duration = 250ms
// Frequency = 784Hz, duration = 250ms
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
411
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
procedure Melody();
begin
Tone1(); Tone2();
Tone1(); Tone2();
Tone1(); Tone2();
Tone1(); Tone2();
Tone1(); Tone2();
Tone3(); Tone3();
end;
// Plays the melody "Yellow house"
Tone3();
Tone3();
Tone3();
Tone3();
Tone3();
Tone2();
procedure ToneA();
begin
Sound_Play( 880, 50);
end;
Tone3();
Tone3();
Tone3();
Tone2(); Tone1();
// Tones used in Melody2 function
procedure ToneC();
begin
Sound_Play(1046, 50);
end;
procedure ToneE();
begin
Sound_Play(1318, 50);
end;
procedure Melody2();
var counter : byte;
begin
for counter := 9 downto 1 do
begin
ToneA();
ToneC();
ToneE();
end;
end;
// Plays Melody2
begin
ANSEL := 0;
ANSELH := 0;
// Configure AN pins as digital I/O
C1ON_bit := 0;
C2ON_bit := 0;
// Disable comparators
TRISB := 0xF0;
TRISD := 0xF7
// Configure RB7..RB4 as input
// Configure RD3 as output
Sound_Init(PORTD, 3);
Sound_Play(880, 5000);
412
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
while TRUE do
// endless loop
begin
if (Button(PORTB,7,1,1)) then // If PORTB.7 is pressed play Tone1
begin
Tone1();
while (RB7_bit <> 0) do nop; // Wait for button to be released
end;
if (Button(PORTB,6,1,1)) then // If PORTB.6 is pressed play Tone1
begin
Tone2();
while (RB6_bit <> 0) do nop; // Wait for button to be released
end;
if (Button(PORTB,5,1,1)) then
// If PORTB.5 is pressed play Tone1
begin
Melody2();
while (RB5_bit <> 0) do nop; // Wait for button to be released
end;
if (Button(PORTB,4,1,1)) then // If PORTB.4 is pressed play Tone1
begin
Melody();
while (RB4_bit <> 0) do nop;// Wait for button to be released
end;
end;
end.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
413
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
HW Connection
Example of Sound Library sonnection
414
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI LIBRARY
SPI module is available with a number of PIC MCU models. mikroPascal PRO for PIC provides
a library for initializing Slave mode and comfortable work with Master mode. PIC can easily communicate with other devices via SPI: A/D converters, D/A converters, MAX7219, LTC1290, etc.
You need PIC MCU with hardware integrated SPI (for example, PIC16F877).
Note: Some PIC18 MCUs have multiple SPI modules. Switching between the SPI modules in the
SPI library is done by the SPI_Set_Active function (SPI module has to be previously initialized).
Note: In order to use the desired SPI library routine, simply change the number 1 in the prototype
with the appropriate module number, i.e. SPI2_Init();
Library Routines
-
SPI1_Init
SPI1_Init_Advanced
SPI1_Read
SPI1_Write
SPI_Set_Active
SPI1_Init
Prototype
procedure SPI1_Init();
Returns
Nothing.
Configures and initializes SPI with default settings. SPI1_Init_Advanced or
SPI1_Init needs to be called before using other functions from SPI Library.
Default settings are:
Description
-
master mode
clock Fosc/4
clock idle state low
data transimtted on low to high edge
input data sampled at the middle of interval
Requires
You need PIC MCU with hardware integrated SPI.
Example
SPI1_Init();
// Initialize the SPI module with default settings
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
415
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI1_Init_Advanced
Prototype
procedure SPI1_Init_Advanced(master, data_sample, clock_idle,
transmit_edge : byte);
Returns
Nothing.
Configures and initializes SPI. SPI1_Init_Advanced or SPI1_Init needs to be
called before using other functions of SPI Library.
Parameters mode, data_sample and clock_idle configure the SPI module, and
can have the following values:
Description
Predefined library const
SPI work mode:
Master clock = Fosc/4
_SPI_MASTER_OSC_DIV4
Master clock = Fosc/16
_SPI_MASTER_OSC_DIV16
Master clock = Fosc/64
_SPI_MASTER_OSC_DIV64
Master clock source TMR2
Description
Slave select enabled
Slave select disabled
_SPI_MASTER_TMR2
_SPI_SLAVE_SS_ENABLE
_SPI_SLAVE_SS_DIS
Data sampling interval:
Input data sampled in middle of interval _SPI_DATA_SAMPLE_MIDDLE
Input data sampled at the end of interval _SPI_DATA_SAMPLE_END
SPI clock idle state:
Clock idle HIGH
_SPI_CLK_IDLE_HIGH
Clock idle LOW
_SPI_CLK_IDLE_LOW
Transmit edge:
416
Data transmit on low to high edge
_SPI_LOW_2_HIGH
Data transmit on high to low edge
_SPI_HIGH_2_LOW
Requires
You need PIC MCU with hardware integrated SPI.
Example
// Set SPI to master mode, clock = Fosc/4, data sampled at the
middle of interval, clock idle state low and data transmitted at
low to high edge:
SPI1_Init_Advanced(_SPI_MASTER_OSC_DIV4, _SPI_DATA_SAMPLE_MIDDLE,
_SPI_CLK_IDLE_LOW, _SPI_LOW_2_HIGH);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI1_Read
Prototype
function SPI1_Read(buffer : byte) : byte;
Returns
Returns the received data.
Description Provides clock by sending buffer and receives data at the end of period.
You need PIC MCU with hardware integrated SPI.
Requires
SPI must be initialized and communication established before using this function. See SPI1_Init_Advanced or SPI1_Init.
var buffer, take : byte;
Example
begin
take := SPI1_Read(buffer);
end.
SPI1_Write
Prototype
procedure SPI1_Write(data_ : byte);
Returns
Nothing.
Description Writes byte data to SSPBUF, and immediately starts the transmission.
You need PIC MCU with hardware integrated SPI.
Requires
Example
SPI must be initialized and communication established before using this function. See SPI1_Init_Advanced or SPI1_Init.
SPI1_Write(1);
SPI_Set_Active
Prototype
procedure SPI_Set_Active (read_ptr : ^TSpi_Rd_Ptr);
Returns
Nothing.
Sets the active SPI module which will be used by the SPI routines.
Description Parameters :
- read_ptr: SPI1_Read handler
Routine is available only for MCUs with two SPI modules.
Requires
Example
Used SPI module must be initialized before using this function. See the
SPI1_Init, SPI1_Init_Advanced
SPI_Set_Active(@SPI2_Read); // Sets the SPI2 module active
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
417
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Example
The code demonstrates how to use SPI library functions for communication between
SPI module of the MCU and Microchip's MCP4921 12-bit D/A converter
program SPI;
// DAC module connections
var Chip_Select : sbit at RC1_bit;
Chip_Select_Direction : sbit at TRISC1_bit;
// End DAC module connections
var value : word;
procedure InitMain();
begin
TRISB0_bit := 1;
TRISB1_bit := 1;
Chip_Select := 1;
Chip_Select_Direction := 0;
SPI1_Init();
end;
//
//
//
//
//
Set RA0 pin as
Set RA1 pin as
Deselect DAC
Set CS# pin as
Initialize SPI
input
input
Output
module
// DAC increments (0..4095) --> output voltage (0..Vref)
procedure DAC_Output( valueDAC : word);
var temp : byte;
begin
Chip_Select := 0;
// Select DAC chip
// Send High Byte
temp := word(valueDAC shr 8) and 0x0F;
// Store
valueDAC[11..8] to temp[3..0]
temp := temp or 0x30; // Define DAC setting, see MCP4921 datasheet
SPI1_Write(temp);
// Send high byte via SPI
// Send Low Byte
temp := valueDAC;
SPI1_Write(temp);
Chip_Select := 1;
end;
// Store valueDAC[7..0] to temp[7..0]
// Send low byte via SPI
// Deselect DAC chip
begin
ANSEL := 0;
ANSELH := 0;
InitMain();
418
// Perform main initialization
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
value := 2048;
Libraries
// When program starts, DAC gives
//
the output in the mid-range
while ( TRUE ) do
begin
// Endless loop
if ((RA0_bit) and (value < 4095)) then
is pressed
Inc(value)
//
else
begin
if ((RA1_bit) and (value > 0)) then
is pressed
Dec(value);
//
end;
DAC_Output(value);
Delay_ms(1);
end;
// If PA0 button
increment value
// If PA1 button
decrement value
// Send value to DAC chip
// Slow down key repeat pace
end.
HW Connection
SPI HW connection
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
419
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI ETHERNET LIBRARY
The ENC28J60 is a stand-alone Ethernet controller with an industry standard Serial Peripheral Interface (SPI™). It is designed to serve as an Ethernet network interface for any controller equipped with SPI.
The ENC28J60 meets all of the IEEE 802.3 specifications. It incorporates a number
of packet filtering schemes to limit incoming packets. It also provides an internal
DMA module for fast data throughput and hardware assisted IP checksum calculations. Communication with the host controller is implemented via two interrupt pins
and the SPI, with data rates of up to 10 Mb/s. Two dedicated pins are used for LED
link and network activity indication.
This library is designed to simplify handling of the underlying hardware (ENC28J60).
It works with any PIC with integrated SPI and more than 4 Kb ROM memory. 38 to
40 MHz clock is recommended to get from 8 to 10 Mhz SPI clock, otherwise PIC
should be clocked by ENC28J60 clock output due to its silicon bug in SPI hardware.
If you try lower PIC clock speed, there might be board hang or miss some requests.
SPI Ethernet library supports:
- IPv4 protocol.
- ARP requests.
- ICMP echo requests.
- UDP requests.
- TCP requests (no stack, no packet reconstruction).
- ARP client with cache.
- DNS client.
- UDP client.
- DHCP client.
- packet fragmentation is NOT supported.
Note: Due to PIC16 RAM/Flash limitations PIC16 library does NOT have ARP, DNS,
UDP and DHCP client support implemented.
Note: Global library variable SPI_Ethernet_userTimerSec is used to keep track of
time for all client implementations (ARP, DNS, UDP and DHCP). It is user responsibility to increment this variable each second in it's code if any of the clients is used.
Note: For advanced users there are header files ("eth_enc28j60LibDef.h" and
"eth_enc28j60LibPrivate.h") in Uses\P16 and Uses\P18 folders of the compiler
with description of all routines and global variables, relevant to the user, implemented in the SPI Ethernet Library.
Note: The appropriate hardware SPI module must be initialized before using any of
the SPI Ethernet library routines. Refer to SPI Library.
For MCUs with two SPI modules it is possible to initialize both of them and then
switch by using the SPI_Set_Active() routine.
420
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
External dependencies of SPI Ethernet Library
The following variables
must be defined in all
projects using SPI Ethernet Library:
Description:
Example :
var SPI_Ethernet_CS :
var SPI_Ethernet_CS :
ENC28J60 chip select pin. sbit at RC1_bit;
sbit; sfr; external;
var SPI_Ethernet_RST :
var SPI_Ethernet_RST
ENC28J60 reset pin.
sbit; sfr; external;
: sbit at RC0_bit;
var
var
SPI_Ethernet_CS_Direc Direction of the ENC28J60 SPI_Ethernet_CS_Direc
tion : sbit; sfr;
tion : sbit at
chip select pin.
external;
TRISC1_bit;
var
var
SPI_Ethernet_RST_Dire Direction of the ENC28J60 SPI_Ethernet_RST_Dire
ction : sbit; sfr;
ction : sbit at
reset pin.
external;
TRISC0_bit;
The following routines must be defined in all project
using SPI Ethernet Library:
Description:
Example :
function SPI_Ethernet_UserTCP(remoteHost : ^byte,
remotePort : word,
TCP request
localPort : word,
handler.
reqLength : word): word;
Refer to the library
example at the
bottom of this
page for code
implementation.
function SPI_Ethernet_UserUDP(remoteHost : ^byte,
remotePort : word,
UDP request
destPort : word,
handler.
reqLength : word): word;
Refer to the library
example at the
bottom of this
page for code
implementation.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
421
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Routines
PIC16 and PIC18:
-
SPI_Ethernet_Init
SPI_Ethernet_Enable
SPI_Ethernet_Disable
SPI_Ethernet_doPacket
SPI_Ethernet_putByte
SPI_Ethernet_putBytes
SPI_Ethernet_putString
SPI_Ethernet_putConstString
SPI_Ethernet_putConstBytes
SPI_Ethernet_getByte
SPI_Ethernet_getBytes
SPI_Ethernet_UserTCP
SPI_Ethernet_UserUDP
PIC18 Only:
-
422
SPI_Ethernet_getIpAddress
SPI_Ethernet_getGwIpAddress
SPI_Ethernet_getDnsIpAddress
SPI_Ethernet_getIpMask
SPI_Ethernet_confNetwork
SPI_Ethernet_arpResolve
SPI_Ethernet_sendUDP
SPI_Ethernet_dnsResolve
SPI_Ethernet_initDHCP
SPI_Ethernet_doDHCPLeaseTime
SPI_Ethernet_renewDHCP
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Ethernet_Init
Prototype
procedure SPI_Ethernet_Init(mac: ^byte; ip: ^byte; fullDuplex:
byte);
Returns
Nothing.
This is MAC module routine. It initializes ENC28J60 controller. This function is
internaly splited into 2 parts to help linker when coming short of memory.
ENC28J60 controller settings (parameters not mentioned here are set to default):
- receive buffer start address : 0x0000.
- receive buffer end address : 0x19AD.
- transmit buffer start address: 0x19AE.
- transmit buffer end address : 0x1FFF.
- RAM buffer read/write pointers in auto-increment mode.
- receive filters set to default: CRC + MAC Unicast + MAC Broadcast in OR mode.
- flow control with TX and RX pause frames in full duplex mode.
- frames are padded to 60 bytes + CRC.
- maximum packet size is set to 1518.
Description - Back-to-Back Inter-Packet Gap: 0x15 in full duplex mode; 0x12 in half duplex mode.
- Non-Back-to-Back Inter-Packet Gap: 0x0012 in full duplex mode; 0x0C12 in
half duplex mode.
- Collision window is set to 63 in half duplex mode to accomodate some
ENC28J60 revisions silicon bugs.
- CLKOUT output is disabled to reduce EMI generation.
- half duplex loopback disabled.
- LED configuration: default (LEDA-link status, LEDB-link activity).
Parameters:
- mac: RAM buffer containing valid MAC address.
- ip: RAM buffer containing valid IP address.
- fullDuplex: ethernet duplex mode switch. Valid values: 0 (half duplex mode)
and 1 (full duplex mode).
Global variables :
Requires
-
SPI_Ethernet_CS: Chip Select line
SPI_Ethernet_CS_Direction: Direction of the Chip Select pin
SPI_Ethernet_RST: Reset line
SPI_Ethernet_RST_Direction: Direction of the Reset pin
must be defined before using this function.
The SPI module needs to be initialized. See the SPI1_Init and
SPI1_Init_Advanced routines.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
423
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
// SPI Ethernet module connections
var SPI_Ethernet_RST : sbit at RC0_bit;
var SPI_Ethernet_CS : sbit at RC1_bit;
var SPI_Ethernet_RST_Direction : sbit at TRISC0_bit;
var SPI_Ethernet_CS_Direction : sbit at TRISC1_bit;
const SPI_Ethernet_HALFDUPLEX = 0;
const SPI_Ethernet_FULLDUPLEX = 1;
Example
var
myMacAddr : array[6] of byte; // my MAC address
myIpAddr : array[4] of byte; // my IP addr
...
myMacAddr[0] := 0x00;
myMacAddr[1] := 0x14;
myMacAddr[2] := 0xA5;
myMacAddr[3] := 0x76;
myMacAddr[4] := 0x19;
myMacAddr[5] := 0x3F;
myIpAddr[0]
myIpAddr[1]
myIpAddr[2]
myIpAddr[3]
:=
:=
:=
:=
192;
168;
1;
60;
SPI_Init();
SPI_Ethernet_Init(myMacAddr, myIpAddr, SPI_Ethernet_FULLDUPLEX);
424
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Ethernet_Enable
Prototype
procedure SPI_Ethernet_Enable(enFlt : byte);
Returns
Nothing.
This is MAC module routine. This routine enables appropriate network traffic on
the ENC28J60 module by the means of it's receive filters (unicast, multicast,
broadcast, crc). Specific type of network traffic will be enabled if a corresponding bit of this routine's input parameter is set. Therefore, more than one type of
network traffic can be enabled at the same time. For this purpose, predefined
library constants (see the table below) can be ORed to form appropriate input
value.
Parameters:
- enFlt: network traffic/receive filter flags. Each bit corresponds to the
appropriate network traffic/receive filter:
Description
Bit
Mask
Description
Predefined library const
0
0x01
MAC Broadcast traffic/receive filter flag. When set, MAC broadcast traffic will be enabled.
1
0x02
MAC Multicast traffic/receive filter
_SPI_Ethernet_MULTICAST
flag. When set, MAC multicast
traffic will be enabled.
2
0x04
not used
none
3
0x08
not used
none
4
0x10
not used
none
5
0x20
CRC check flag. When set, packets with invalid CRC field will be _SPI_Ethernet_CRC
discarded.
6
0x40
not used
7
0x80
MAC Unicast traffic/receive filter
flag. When set, MAC unicast traf- _SPI_Ethernet_UNICAST
fic will be enabled.
_SPI_Ethernet_BROADCAST
none
Note: Advance filtering available in the ENC28J60 module such as Pattern
Match, Magic Packet and Hash Table can not be enabled by this routine. Additionaly, all filters, except CRC, enabled with this routine will work in OR mode,
which means that packet will be received if any of the enabled filters accepts it.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
425
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Note: This routine will change receive filter configuration on-the-fly. It will not, in
any way, mess with enabling/disabling receive/transmit logic or any other part of
Description
the ENC28J60 module. The ENC28J60 module should be properly cofigured by
the means of SPI_Ethernet_Init routine.
Requires
Ethernet module has to be initialized. See SPI_Ethernet_Init.
Example
SPI_Ethernet_Enable(_SPI_Ethernet_CRC or _SPI_Ethernet_UNICAST);
// enable CRC checking and Unicast traffic
SPI_Ethernet_Disable
Prototype
procedure SPI_Ethernet_Disable(disFlt : byte);
Returns
Nothing.
This is MAC module routine. This routine disables appropriate network traffic on the
ENC28J60 module by the means of it's receive filters (unicast, multicast, broadcast,
crc). Specific type of network traffic will be disabled if a corresponding bit of this routine's input parameter is set. Therefore, more than one type of network traffic can be
disabled at the same time. For this purpose, predefined library constants (see the
table below) can be ORed to form appropriate input value.
Parameters:
- disFlt: network traffic/receive filter flags. Each bit corresponds to the
appropriate network traffic/receive filter:
Bit Mask
0
Description
1
426
Description
Predefined library const
MAC Broadcast traffic/receive filter
0x01 flag. When set, MAC broadcast traf- _SPI_Ethernet_BROADCAST
fic will be disabled.
MAC Multicast traffic/receive filter
0x02 flag. When set, MAC multicast traf- _SPI_Ethernet_MULTICAST
fic will be disabled.
2
0x04 not used
none
3
0x08 not used
none
4
0x10 not used
none
5
CRC check flag. When set, CRC
_SPI_Ethernet_CRC
0x20 check will be disabled and packets
with invalid CRC field will be accepted.
6
0x40 not used
none
7
MAC Unicast traffic/receive filter
0x80 flag. When set, MAC unicast traffic
will be disabled.
_SPI_Ethernet_UNICAST
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Note: Advance filtering available in the ENC28J60 module such as Pattern
Match, Magic Packet and Hash Table can not be disabled by this routine.
Description Note: This routine will change receive filter configuration on-the-fly. It will not, in
any way, mess with enabling/disabling receive/transmit logic or any other part of
the ENC28J60 module. The ENC28J60 module should be properly cofigured by
the means of SPI_Ethernet_Init routine.
Requires
Ethernet module has to be initialized. See SPI_Ethernet_Init.
Example
SPI_Ethernet_Disable(_SPI_Ethernet_CRC or _SPI_Ethernet_UNICAST);
// disable CRC checking and Unicast traffic
SPI_Ethernet_doPacket
Prototype
function SPI_Ethernet_doPacket() : byte;
Returns
- 0 - upon successful packet processing (zero packets received or received
packet processed successfully).
- 1 - upon reception error or receive buffer corruption. ENC28J60 controller
needs to be restarted.
- 2 - received packet was not sent to us (not our IP, nor IP broadcast address).
- 3 - received IP packet was not IPv4.
- 4 - received packet was of type unknown to the library.
This is MAC module routine. It processes next received packet if such exists.
Packets are processed in the following manner:
- ARP & ICMP requests are replied automatically.
- upon TCP request the SPI_Ethernet_UserTCP function is called for further
Description
processing.
- upon UDP request the SPI_Ethernet_UserUDP function is called for further
processing.
Note: SPI_Ethernet_doPacket must be called as often as possible in user's code.
Requires
Ethernet module has to be initialized. See SPI_Ethernet_Init.
Example
while true do
begin
...
SPI_Ethernet_doPacket(); // process received packets
...
end;
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
427
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Ethernet_putByte
Prototype
procedure SPI_Ethernet_putByte(v : byte);
Returns
Nothing.
This is MAC module routine. It stores one byte to address pointed by the current ENC28J60 write pointer (EWRPT).
Description
Parameters:
- v: value to store
Requires
Ethernet module has to be initialized. See SPI_Ethernet_Init.
Example
var
data : byte;
...
SPI_Ethernet_putByte(data);
buffer
// put an byte into ENC28J60
SPI_Ethernet_putBytes
Prototype
procedure SPI_Ethernet_putBytes(ptr : ^byte; n : byte);
Returns
Nothing.
This is MAC module routine. It stores requested number of bytes into
ENC28J60 RAM starting from current ENC28J60 write pointer (EWRPT) location.
Description Parameters:
- ptr: RAM buffer containing bytes to be written into ENC28J60 RAM.
- n: number of bytes to be written.
428
Requires
Ethernet module has to be initialized. See SPI_Ethernet_Init.
Example
var
buffer : array[17] of byte;
...
buffer := 'mikroElektronika';
...
SPI_Ethernet_putBytes(buffer, 16); // put an RAM array into
ENC28J60 buffer
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Ethernet_putConstBytes
Prototype
procedure SPI_Ethernet_putConstBytes(const ptr : ^byte; n : byte);
Returns
Nothing.
This is MAC module routine. It stores requested number of const bytes into
ENC28J60 RAM starting from current ENC28J60 write pointer (EWRPT) location.
Description Parameters:
- ptr: const buffer containing bytes to be written into ENC28J60 RAM.
- n: number of bytes to be written.
Requires
Ethernet module has to be initialized. See SPI_Ethernet_Init.
Example
const
buffer : array[17] of byte;
...
buffer := 'mikroElektronika';
...
SPI_Ethernet_putConstBytes(buffer, 16); // put a const array
into ENC28J60 buffer
SPI_Ethernet_putString
Prototype
function SPI_Ethernet_putString(ptr : ^byte) : word;
Returns
Number of bytes written into ENC28J60 RAM.
This is MAC module routine. It stores whole string (excluding null termination) into
ENC28J60 RAM starting from current ENC28J60 write pointer (EWRPT) location.
Description
Parameters:
- ptr: string to be written into ENC28J60 RAM.
Requires
Ethernet module has to be initialized. See SPI_Ethernet_Init.
Example
var
buffer : string[16];
...
buffer := 'mikroElektronika';
...
SPI_Ethernet_putString(buffer); // put a RAM string into
ENC28J60 buffer
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
429
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Ethernet_putConstString
Prototype
function SPI_Ethernet_putConstString(const ptr : ^byte) : word;
Returns
Number of bytes written into ENC28J60 RAM.
This is MAC module routine. It stores whole const string (excluding null termination)
into ENC28J60 RAM starting from current ENC28J60 write pointer (EWRPT) location.
Description
Parameters:
- ptr: const string to be written into ENC28J60 RAM.
Requires
Ethernet module has to be initialized. See SPI_Ethernet_Init.
Example
const
buffer : string[16];
...
buffer := 'mikroElektronika';
...
SPI_Ethernet_putConstString(buffer); // put a const string into
ENC28J60 buffer
SPI_Ethernet_getByte
430
Prototype
function SPI_Ethernet_getByte() : byte;
Returns
Byte read from ENC28J60 RAM.
Description
This is MAC module routine. It fetches a byte from address pointed to by current ENC28J60 read pointer (ERDPT).
Requires
Ethernet module has to be initialized. See SPI_Ethernet_Init.
Example
var
buffer : byte;
...
buffer := SPI_Ethernet_getByte(); // read a byte from ENC28J60
buffer
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Ethernet_getBytes
Prototype
procedure SPI_Ethernet_getBytes(ptr : ^byte; addr : word; n :
byte);
Returns
Nothing.
This is MAC module routine. It fetches equested number of bytes from
ENC28J60 RAM starting from given address. If value of 0xFFFF is passed as the
address parameter, the reading will start from current ENC28J60 read pointer
(ERDPT) location.
Description
Parameters:
- ptr: buffer for storing bytes read from ENC28J60 RAM.
- addr: ENC28J60 RAM start address. Valid values: 0..8192.
- n: number of bytes to be read.
Requires
Ethernet module has to be initialized. See SPI_Ethernet_Init.
Example
var
buffer: array[16] of byte;
...
SPI_Ethernet_getBytes(buffer, 0x100, 16); // read 16 bytes,
starting from address 0x100
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
431
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Ethernet_UserTCP
Prototype
function SPI_Ethernet_UserTCP(var remoteHost : array[4] of byte;
remotePort, localPort, reqLength : word) : word;
Returns
- 0 - there should not be a reply to the request.
- Length of TCP/HTTP reply data field - otherwise.
This is TCP module routine. It is internally called by the library. The user
accesses to the TCP/HTTP request by using some of the SPI_Ethernet_get routines. The user puts data in the transmit buffer by using some of the SPI_Ethernet_put routines. The function must return the length in bytes of the TCP/HTTP
reply, or 0 if there is nothing to transmit. If there is no need to reply to the
TCP/HTTP requests, just define this function with return(0) as a single statement.
Description Parameters:
-
remoteHost: client's IP address.
remotePort: client's TCP port.
localPort: port to which the request is sent.
reqLength: TCP/HTTP request data field length.
Note: The function source code is provided with appropriate example projects.
The code should be adjusted by the user to achieve desired reply.
432
Requires
Ethernet module has to be initialized. See SPI_Ethernet_Init.
Example
This function is internally called by the library and should not be called by the
user's code.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Ethernet_UserUDP
Prototype
function SPI_Ethernet_UserUDP(var remoteHost : array[4] of byte;
remotePort, destPort, reqLength : word) : word;
Returns
- 0 - there should not be a reply to the request.
- Length of UDP reply data field - otherwise.
This is UDP module routine. It is internally called by the library. The user
accesses to the UDP request by using some of the SPI_Ethernet_get routines.
The user puts data in the transmit buffer by using some of the
SPI_Ethernet_put routines. The function must return the length in bytes of the
UDP reply, or 0 if nothing to transmit. If you don't need to reply to the UDP
requests, just define this function with a return(0) as single statement.
Description
Parameters:
-
remoteHost: client's IP address.
remotePort: client's port.
destPort: port to which the request is sent.
reqLength: UDP request data field length.
Note: The function source code is provided with appropriate example projects.
The code should be adjusted by the user to achieve desired reply.
Requires
Ethernet module has to be initialized. See SPI_Ethernet_Init.
Example
This function is internally called by the library and should not be called by the
user's code.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
433
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Ethernet_getIpAddress
Prototype
function SPI_Ethernet_getIpAddress() : word;
Returns
Ponter to the global variable holding IP address.
This routine should be used when DHCP server is present on the network to
fetch assigned IP address.
Description
Note: User should always copy the IP address from the RAM location returned
by this routine into it's own IP address buffer. These locations should not be
altered by the user in any case!
Ethernet module has to be initialized. See SPI_Ethernet_Init.
Requires
Available for PIC18 family MCUs only.
Example
var
ipAddr : array[4] of byte; // user IP address buffer
...
memcpy(ipAddr, SPI_Ethernet_getIpAddress(), 4); // fetch IP
address
SPI_Ethernet_getGwIpAddress
Prototype
function SPI_Ethernet_getGwIpAddress() : word;
Returns
Ponter to the global variable holding gateway IP address.
This routine should be used when DHCP server is present on the network to
fetch assigned gateway IP address.
Description
Note: User should always copy the IP address from the RAM location returned
by this routine into it's own gateway IP address buffer. These locations should
not be altered by the user in any case!
Ethernet module has to be initialized. See SPI_Ethernet_Init.
Requires
Available for PIC18 family MCUs only.
Example
434
var
gwIpAddr : array[4] of byte; // user gateway IP address
buffer
...
memcpy(gwIpAddr, SPI_Ethernet_getGwIpAddress(), 4); // fetch
gateway IP address
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Ethernet_getDnsIpAddress
Prototype
function SPI_Ethernet_getDnsIpAddress() : word;
Returns
Ponter to the global variable holding DNS IP address.
This routine should be used when DHCP server is present on the network to
fetch assigned DNS IP address.
Description
Note: User should always copy the IP address from the RAM location returned
by this routine into it's own DNS IP address buffer. These locations should not
be altered by the user in any case!
Ethernet module has to be initialized. See SPI_Ethernet_Init.
Requires
Available for PIC18 family MCUs only.
Example
var
dnsIpAddr : array[4] of byte; // user DNS IP address buffer
...
memcpy(dnsIpAddr, SPI_Ethernet_getDnsIpAddress(), 4); // fetch
DNS server address
SPI_Ethernet_getIpMask
Prototype
function SPI_Ethernet_getIpMask() : word;
Returns
Ponter to the global variable holding IP subnet mask.
This routine should be used when DHCP server is present on the network to
fetch assigned IP subnet mask.
Description
Note: User should always copy the IP address from the RAM location returned
by this routine into it's own IP subnet mask buffer. These locations should not
be altered by the user in any case!
Ethernet module has to be initialized. See SPI_Ethernet_Init.
Requires
Available for PIC18 family MCUs only.
Example
var
IpMask : array[4] of byte; // user IP subnet mask buffer
...
memcpy(IpMask, SPI_Ethernet_getIpMask(), 4); // fetch IP subnet
mask
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
435
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Ethernet_confNetwork
Prototype
procedure SPI_Ethernet_confNetwork(var ipMask, gwIpAddr,
dnsIpAddr : array[4] of byte);
Returns
Nothing.
Configures network parameters (IP subnet mask, gateway IP address, DNS IP
address) when DHCP is not used.
Parameters:
Description - ipMask: IP subnet mask.
- gwIpAddr gateway IP address.
- dnsIpAddr: DNS IP address.
Note: The above mentioned network parameters should be set by this routine
only if DHCP module is not used. Otherwise DHCP will override these settings.
Ethernet module has to be initialized. See SPI_Ethernet_Init.
Requires
Available for PIC18 family MCUs only.
var
ipMask
: array[4] of byte;
255.255.255.0)
gwIpAddr : array[4] of byte;
dnsIpAddr : array[4] of byte;
...
gwIpAddr[0] := 192;
gwIpAddr[1] := 168;
gwIpAddr[2] := 20;
gwIpAddr[3] := 6;
Example
dnsIpAddr[0]
dnsIpAddr[1]
dnsIpAddr[2]
dnsIpAddr[3]
:=
:=
:=
:=
// network mask (for example :
// gateway (router) IP address
// DNS server IP address
192;
168;
20;
100;
ipMask[0]
:= 255;
ipMask[1]
:= 255;
ipMask[2]
:= 255;
ipMask[3]
:= 0;
...
SPI_Ethernet_confNetwork(ipMask, gwIpAddr, dnsIpAddr); // set
network configuration parameters
436
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Ethernet_arpResolve
Prototype
function SPI_Ethernet_arpResolve(var ip : array[4] of byte; tmax
: byte) : word;
Returns
- MAC address behind the IP address - the requested IP address was resolved.
- 0 - otherwise.
This is ARP module routine. It sends an ARP request for given IP address and
waits for ARP reply. If the requested IP address was resolved, an ARP cash
entry is used for storing the configuration. ARP cash can store up to 3 entries.
For ARP cash structure refer to "eth_enc28j60LibDef.h" header file in the
compiler's Uses/P18 folder.
Description Parameters:
- ip: IP address to be resolved.
- tmax: time in seconds to wait for an reply.
Note: The Ethernet services are not stopped while this routine waits for ARP
reply. The incoming packets will be processed normaly during this time.
Ethernet module has to be initialized. See SPI_Ethernet_Init.
Requires
Available for PIC18 family MCUs only.
Example
var
IpAddr : array[4] of byte; // IP address
...
IpAddr[0] := 192;
IpAddr[0] := 168;
IpAddr[0] := 1;
IpAddr[0] := 1;
...
SPI_Ethernet_arpResolve(IpAddr, 5); // get MAC address behind
the above IP address, wait 5 secs for the response
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
437
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Ethernet_sendUDP
Prototype
function SPI_Ethernet_sendUDP(var destIP : array[4] of byte;
sourcePort, destPort : word; pkt : ^byte; pktLen : word) : byte;
Returns
- 1 - UDP packet was sent successfully.
- 0 - otherwise.
This is UDP module routine. It sends an UDP packet on the network.
Parameters:
Description -
destIP: remote host IP address.
sourcePort: local UDP source port number.
destPort: destination UDP port number.
pkt: packet to transmit.
pktLen: length in bytes of packet to transmit.
Ethernet module has to be initialized. See SPI_Ethernet_Init.
Requires
Available for PIC18 family MCUs only.
Example
438
var
IpAddr : array[4] of byte; // remote IP address
...
IpAddr[0] := 192;
IpAddr[0] := 168;
IpAddr[0] := 1;
IpAddr[0] := 1;
...
SPI_Ethernet_sendUDP(IpAddr, 10001, 10001, 'Hello', 5); // send
Hello message to the above IP address, from UDP port 10001 to
UDP port 10001
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Ethernet_dnsResolve
Prototype
function SPI_Ethernet_dnsResolve(var host : array[4] of byte;
tmax : byte) : word;
Returns
- pointer to the location holding the IP address - the requested host name was
resolved.
- 0 - otherwise.
This is DNS module routine. It sends an DNS request for given host name and
waits for DNS reply. If the requested host name was resolved, it's IP address is
stored in library global variable and a pointer containing this address is returned
by the routine. UDP port 53 is used as DNS port.
Parameters:
Description
- host: host name to be resolved.
- tmax: time in seconds to wait for an reply.
Note: The Ethernet services are not stopped while this routine waits for DNS
reply. The incoming packets will be processed normaly during this time.
Note: User should always copy the IP address from the RAM location returned
by this routine into it's own resolved host IP address buffer. These locations
should not be altered by the user in any case!
Ethernet module has to be initialized. See SPI_Ethernet_Init.
Requires
Available for PIC18 family MCUs only.
Example
var
remoteHostIpAddr : array[4] of byte; // user host IP address
buffer
...
// SNTP server:
// Zurich, Switzerland: Integrated Systems Lab, Swiss Fed.
Inst. of Technology
// 129.132.2.21: swisstime.ethz.ch
// Service Area: Switzerland and Europe
memcpy(remoteHostIpAddr,
SPI_Ethernet_dnsResolve('swisstime.ethz.ch', 5), 4);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
439
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Ethernet_initDHCP
Prototype
function SPI_Ethernet_initDHCP(tmax : byte) : byte;
Returns
- 1 - network parameters were obtained successfully.
- 0 - otherwise.
This is DHCP module routine. It sends an DHCP request for network parameters (IP, gateway, DNS addresses and IP subnet mask) and waits for DHCP
reply. If the requested parameters were obtained successfully, their values are
stored into the library global variables.
These parameters can be fetched by using appropriate library IP get routines:
-
SPI_Ethernet_getIpAddress - fetch IP address.
SPI_Ethernet_getGwIpAddress - fetch gateway IP address.
SPI_Ethernet_getDnsIpAddress - fetch DNS IP address.
SPI_Ethernet_getIpMask - fetch IP subnet mask.
Description UDP port 68 is used as DHCP client port and UDP port 67 is used as DHCP
server port.
Parameters:
- tmax: time in seconds to wait for an reply.
Note: The Ethernet services are not stopped while this routine waits for DNS
reply. The incoming packets will be processed normaly during this time.
Note: When DHCP module is used, global library variable
SPI_Ethernet_userTimerSec is used to keep track of time. It is user responsibility to increment this variable each second in it's code.
Ethernet module has to be initialized. See SPI_Ethernet_Init.
Requires
Available for PIC18 family MCUs only.
Example
440
...
SPI_Ethernet_initDHCP(5); // get network configuration from
DHCP server, wait 5 sec for the response
...
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Ethernet_doDHCPLeaseTime
Prototype
function SPI_Ethernet_doDHCPLeaseTime() : byte;
Returns
- 0 - lease time has not expired yet.
- 1 - lease time has expired, it's time to renew it.
This is DHCP module routine. It takes care of IP address lease time by decreDescription menting the global lease time library counter. When this time expires, it's time to
contact DHCP server and renew the lease.
Ethernet module has to be initialized. See SPI_Ethernet_Init.
Requires
Available for PIC18 family MCUs only.
Example
while true do
begin
...
if (SPI_Ethernet_doDHCPLeaseTime() <> 0) then
begin
... // it's time to renew the IP address lease
end;
end;
SPI_Ethernet_renewDHCP
Prototype
function SPI_Ethernet_renewDHCP(tmax : byte) : byte;
Returns
- 1 - upon success (lease time was renewed).
- 0 - otherwise (renewal request timed out).
This is DHCP module routine. It sends IP address lease time renewal request to
DHCP server.
Description
Parameters:
- tmax: time in seconds to wait for an reply.
Ethernet module has to be initialized. See SPI_Ethernet_Init.
Requires
Available for PIC18 family MCUs only.
Example
while true do
begin
...
if (SPI_Ethernet_doDHCPLeaseTime() <> 0) then
begin
SPI_Ethernet_renewDHCP(5); // it's time to renew the IP
address lease, with 5 secs for a reply
end;
...
end;
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
441
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Example
This code shows how to use the PIC18 Ethernet mini library :
- the board will reply to ARP & ICMP echo requests
- the board will reply to UDP requests on any port :
returns the request in upper char with a header made of remote host IP &
port number
- the board will reply to HTTP requests on port 80, GET method with pathnames :
/ will return the HTML main page
/s will return board status as text string
/t0 ... /t7 will toggle RD0 to RD7 bit and return HTML main page
all other requests return also HTML main page.
program enc_ethernet;
{***********************************
* RAM variables
*}
var myMacAddr
: array[6] of byte ; // my MAC address
myIpAddr
: array[4] of byte ; // my IP address
// mE ehternet NIC pinout
SPI_Ethernet_Rst : sbit at PORTC.B0;
SPI_Ethernet_CS : sbit at PORTC.B1;
SPI_Ethernet_Rst_Direction : sbit at TRISC.B0;
SPI_Ethernet_CS_Direction : sbit at TRISC.B1;
// end ethernet NIC definitions
{************************************************************
* ROM constant strings
*}
const httpHeader : string[30] = 'HTTP/1.1 200 OK'+#10+'Content-type:
' ; // HTTP header
const httpMimeTypeHTML : string[11]
= 'text/html'+#10+#10 ;
// HTML MIME type
const httpMimeTypeScript : string[12] = 'text/plain'+#10+#10 ;
// TEXT MIME type
const httpMethod : string[5] = 'GET /';
{*
* web page, splited into 2 parts :
* when coming short of ROM, fragmented data is handled more efficiently by linker
*
* this HTML page calls the boards to get its status, and builds
itself with javascript
*}
442
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
const indexPage : string[759] =
'<meta http-equiv="refresh"
content="3;url=http://192.168.20.60">' +
'<HTML><HEAD></HEAD><BODY>'+
'<h1>PIC + ENC28J60 Mini Web Server</h1>'+
'<a href=/>Reload</a>'+
'<script src=/s></script>'+
'<table><tr><td valign=top><table border=1
style="font-size:20px ;font-family: terminal ;">'+
'<tr><th colspan=2>ADC</th></tr>'+
'<tr><td>AN2</td><td><script>document.write(AN2)</script></td></tr>'
+
'<tr><td>AN3</td><td><script>document.write(AN3)</script></td></tr>'
+
'</table></td><td><table border=1 style="fontsize:20px ;font-family: terminal ;">'+
'<tr><th colspan=2>PORTB</th></tr>'+
'<script>'+
'var str,i;'+
'str="";'+
'for(i=0;i<8;i++)'+
'{str+="<tr><td bgcolor=pink>BUTTON #"+i+"</td>";'+
'if(PORTB&(1<<i)){str+="<td bgcolor=red>ON";}'+
'else {str+="<td bgcolor=#cccccc>OFF";}'+
'str+="</td></tr>";}'+
'document.write(str) ;'+
'</script>';
const indexPage2 : string[466] =
'</table></td><td>'+
'<table border=1 style="font-size:20px ;fontfamily: terminal ;">'+
'<tr><th colspan=3>PORTD</th></tr>'+
'<script>'+
'var str,i;'+
'str="";'+
'for(i=0;i<8;i++)'+
'{str+="<tr><td bgcolor=yellow>LED #"+i+"</td>";'+
'if(PORTD&(1<<i)){str+="<td bgcolor=red>ON";}'+
'else {str+="<td bgcolor=#cccccc>OFF";}'+
'str+="</td><td><a
href=/t"+i+">Toggle</a></td></tr>";}'+
'document.write(str) ;'+
'</script>'+
'</table></td></tr></table>'+
'This is HTTP request
#<script>document.write(REQ)</script></BODY></HTML>';
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
443
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
var
getRequest : array[15] of byte; // HTTP request buffer
dyna
: array[30] of byte;
// buffer for dynamic
response
tmp: string[11];
// auxiliary ram string
httpCounter : word ;
// counter of HTTP requests
{*******************************************
* user defined functions
*}
{*
* this function is called by the library
* the user accesses to the HTTP request by successive calls to
SPI_Ethernet_getByte()
* the user puts data in the transmit buffer by successive calls to
SPI_Ethernet_putByte()
* the function must return the length in bytes of the HTTP reply,
or 0 if nothing to transmit
*
* if you don't need to reply to HTTP requests,
* just define this function with a return(0) as single statement
*
*}
function SPI_Ethernet_UserTCP(var remoteHost : array[4] of byte;
remotePort, localPort, reqLength
: word) : word;
var i : word ;
// my reply length
bitMask : byte ; // for bit mask
begin
result := 0;
if(localPort <> 80) then
// I listen only to web request on port
80
begin
result := 0;
exit;
end;
// get 10 first bytes only of the request, the rest does not matter here
for i := 0 to 9 do
getRequest[i] := SPI_Ethernet_getByte() ;
getRequest[i] := 0 ;
// copy httpMethod to ram for use in memcmp routine
for i := 0 to 4 do
tmp[i] := httpMethod[i];
444
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
if(memcmp(@getRequest, @tmp, 5) <> 0) then
supported here
begin
result := 0 ;
exit;
end;
// only GET method is
Inc(httpCounter) ; // one more request done
if(getRequest[5] = 's') then // if request path name starts with
s, store dynamic data in transmit buffer
begin
// the text string replied by this request can be interpreted as javascript statements
// by browsers
result := SPI_Ethernet_putConstString(@httpHeader) ;
// HTTP header
result
:=
result
+
SPI_Ethernet_putConstString(@httpMimeTypeScript) ; // with text MIME
type
// add AN2 value to reply
WordToStr(ADC_Read(2), dyna) ;
tmp := 'var AN2=';
result := result + SPI_Ethernet_putString(@tmp) ;
result := result + SPI_Ethernet_putString(@dyna) ;
tmp := ';';
result := result + SPI_Ethernet_putString(@tmp) ;
// add AN3 value to reply
WordToStr(ADC_Read(3), dyna) ;
tmp := 'var AN3=';
result := result + SPI_Ethernet_putString(@tmp) ;
result := result + SPI_Ethernet_putString(@dyna) ;
tmp := ';';
result := result + SPI_Ethernet_putString(@tmp) ;
// add PORTB value (buttons) to reply
tmp := 'var PORTB= ';
result := result + SPI_Ethernet_putString(@tmp) ;
WordToStr(PORTB, dyna) ;
result := result + SPI_Ethernet_putString(@dyna) ;
tmp := ';';
result := result + SPI_Ethernet_putString(@tmp) ;
// add PORTD value (LEDs) to reply
tmp := 'var PORTD= ';
result := result + SPI_Ethernet_putString(@tmp) ;
WordToStr(PORTD, dyna) ;
result := result + SPI_Ethernet_putString(@dyna) ;
tmp := ';';
result := result + SPI_Ethernet_putString(@tmp) ;
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
445
CHAPTER 7
Libraries
mikroPASCAL PRO for PIC
// add HTTP requests counter to reply
WordToStr(httpCounter, dyna) ;
tmp := 'var REQ=
';
result := result + SPI_Ethernet_putString(@tmp) ;
result := result + SPI_Ethernet_putString(@dyna) ;
tmp := ';';
result := result + SPI_Ethernet_putString(@tmp) ;
end
else
if(getRequest[5] = 't') then
// if request path
name starts with t, toggle PORTD (LED) bit number that comes after
begin
bitMask := 0;
if(isdigit(getRequest[6]) <> 0) then // if 0 <= bit number <= 9, bits 8 & 9 does not exist but does not matter
begin
bitMask := getRequest[6] - '0' ; // convert ASCII to
integer
bitMask := 1 shl bitMask ;
// create bit mask
PORTD
:= PORTD xor bitMask ;
// toggle PORTD with
xor operator
end;
end;
if(result = 0) then // what do to by default
begin
result := SPI_Ethernet_putConstString(@httpHeader) ; // HTTP
header
result
:=
result
+
SPI_Ethernet_putConstString(@httpMimeTypeHTML) ; // with HTML MIME
type
result := result + SPI_Ethernet_putConstString(@indexPage) ;
// HTML page first part
result := result + SPI_Ethernet_putConstString(@indexPage2)
;
// HTML page second part
end;
// return to the library with the number of bytes to transmit
end;
{*
* this function is called by the library
* the user accesses to the UDP request by successive calls to
SPI_Ethernet_getByte()
* the user puts data in the transmit buffer by successive calls to
SPI_Ethernet_putByte()
* the function must return the length in bytes of the UDP reply, or
0 if nothing to transmit
*
* if you don't need to reply to UDP requests,
* just define this function with a return(0) as single statement
*
*}
function SPI_Ethernet_UserUDP(var remoteHost : array[4] of byte;
remotePort, destPort, reqLength
: word) : word;
446
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
begin
result := 0;
// reply is made of the remote host IP address in human readable
format
byteToStr(remoteHost[0], dyna) ; // first IP address byte
dyna[3] := '.' ;
byteToStr(remoteHost[1], tmp) ; // second
dyna[4] := tmp[0];
dyna[5] := tmp[1];
dyna[6] := tmp[2];
dyna[7] := '.' ;
byteToStr(remoteHost[2], tmp) ; // second
dyna[8] := tmp[0];
dyna[9] := tmp[1];
dyna[10] := tmp[2];
dyna[11] := '.' ;
byteToStr(remoteHost[3], tmp) ; // second
dyna[12] := tmp[0];
dyna[13] := tmp[1];
dyna[14] := tmp[2];
dyna[15] := ':' ;
// add separator
// then remote host port number
WordToStr(remotePort, tmp) ;
dyna[16] := tmp[0];
dyna[17] := tmp[1];
dyna[18] := tmp[2];
dyna[19] := tmp[3];
dyna[20] := tmp[4];
dyna[21] := '[' ;
WordToStr(destPort, tmp) ;
dyna[22] := tmp[0];
dyna[23] := tmp[1];
dyna[24] := tmp[2];
dyna[25] := tmp[3];
dyna[26] := tmp[4];
dyna[27] := ']' ;
dyna[28] := 0 ;
// the total length of the request is the length of the dynamic
string plus the text of the request
result := 28 + reqLength ;
// puts the dynamic string into the transmit buffer
SPI_Ethernet_putBytes(@dyna, 28) ;
// then puts the request string converted into upper char into the
transmit buffer
while(reqLength <> 0) do
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
447
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
begin
SPI_Ethernet_putByte(SPI_Ethernet_getByte()) ;
reqLength := reqLength - 1;
end;
// back to the library with the length of the UDP reply
end;
begin
ANSEL := 0x0C ;
PORTA := 0 ;
TRISA := 0xff ;
// AN2 and AN3 convertors will be used
// set PORTA as input for ADC
ANSELH := 0;
PORTB := 0 ;
TRISB := 0xff ;
// Configure other AN pins as digital I/O
// set PORTB as input for buttons
PORTD := 0 ;
TRISD := 0 ;
// set PORTD as output
httpCounter := 0;
// set mac address
myMacAddr[0] := 0x00;
myMacAddr[1] := 0x14;
myMacAddr[2] := 0xA5;
myMacAddr[3] := 0x76;
myMacAddr[4] := 0x19;
myMacAddr[5] := 0x3F;
// set IP address
myIpAddr[0] := 192;
myIpAddr[1] := 168;
myIpAddr[2] := 20;
myIpAddr[3] := 60;
{*
* starts ENC28J60 with :
* reset bit on PORTC.B0
* CS bit on PORTC.B1
* my MAC & IP address
* full duplex
*}
SPI1_Init(); // init spi module
SPI_Ethernet_Init(myMacAddr, myIpAddr, _SPI_Ethernet_FULLDUPLEX) ;
// init ethernet module
SPI_Ethernet_setUserHandlers(@SPI_Ethernet_UserTCP,
@SPI_Ethernet_UserUDP); // set user handlers
448
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
while true do // do forever
begin
SPI_Ethernet_doPacket() ; // process incoming Ethernet packets
{*
* add your stuff here if needed
* SPI_Ethernet_doPacket() must be called as often as possible
* otherwise packets could be lost
*}
end;
end.
HW Connection
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
449
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI GRAPHIC LCD LIBRARY
The mikroPascal PRO for PIC provides a library for operating Graphic Lcd 128x64
(with commonly used Samsung KS108/KS107 controller) via SPI interface.
For creating a custom set of Glcd images use Glcd Bitmap Editor Tool.
Note: The library uses the SPI module for communication. User must initialize SPI
module before using the SPI Graphic Lcd Library.
For MCUs with two SPI modules it is possible to initialize both of them and then
switch by using the SPI_Set_Active() routine.
Note: This Library is designed to work with the mikroElektronika's Serial Lcd/Glcd
Adapter Board pinout, see schematic at the bottom of this page for details.
External dependencies of SPI Graphic Lcd Library
The implementation of SPI Graphic Lcd Library routines is based on Port Expander
Library routines.
External dependencies are the same as Port Expander Library external dependencies.
Library Routines
Basic routines:
-
SPI_Glcd_Init
SPI_Glcd_Set_Side
SPI_Glcd_Set_Page
SPI_Glcd_Set_X
SPI_Glcd_Read_Data
SPI_Glcd_Write_Data
Advanced routines:
-
450
SPI_Glcd_Fill
SPI_Glcd_Dot
SPI_Glcd_Line
SPI_Glcd_V_Line
SPI_Glcd_H_Line
SPI_Glcd_Rectangle
SPI_Glcd_Box
SPI_Glcd_Circle
SPI_Glcd_Set_Font
SPI_Glcd_Write_Char
SPI_Glcd_Write_Text
SPI_Glcd_Image
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Glcd_Init
Prototype
procedure SPI_Glcd_Init(DeviceAddress : byte);
Returns
Nothing.
Initializes the Glcd module via SPI interface.
Description
Parameters :
- DeviceAddress: spi expander hardware address, see schematic at the
bottom of this page
Global variables :
Requires
-
SPExpanderCS: Chip Select line
SPExpanderRST: Reset line
SPExpanderCS_Direction: Direction of the Chip Select pin
SPExpanderRST_Direction: Direction of the Reset pin
must be defined before using this function.
SPI module needs to be initialized. See SPI1_Init and SPI1_Init_Advanced routines.
Example
// port expander pinout definition
var SPExpanderCS : sbit at RC1_bit;
SPExpanderRST : sbit at RC0_bit;
SPExpanderCS_Direction : sbit at TRISC1_bit;
SPExpanderRST_Direction : sbit at TRISC_bit;
...
// If Port Expander Library uses SPI1 module :
SPI1_Init();
// Initialize SPI module
used with PortExpander
SPI_Glcd_Init(0);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
451
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Glcd_Set_Side
Prototype
procedure SPI_Glcd_Set_Side(x_pos : byte);
Returns
Nothing.
Selects Glcd side. Refer to the Glcd datasheet for detail explanation.
Parameters :
- x_pos: position on x-axis. Valid values: 0..127
Description
The parameter x_pos specifies the Glcd side: values from 0 to 63 specify the
left side, values from 64 to 127 specify the right side.
Note: For side, x axis and page layout explanation see schematic at the bottom
of this page.
Requires
Glcd needs to be initialized for SPI communication, see SPI_Glcd_Init routines.
The following two lines are equivalent, and both of them select the left side of Glcd:
Example
SPI_Glcd_Set_Side(0);
SPI_Glcd_Set_Side(10);
SPI_Glcd_Set_Page
Prototype
procedure SPI_Glcd_Set_Page(page : byte);
Returns
Nothing.
Selects page of Glcd.
Parameters :
Description
- page: page number. Valid values: 0..7
Note: For side, x axis and page layout explanation see schematic at the bottom
of this page.
452
Requires
Glcd needs to be initialized for SPI communication, see SPI_Glcd_Init routines.
Example
SPI_Glcd_Set_Page(5);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Glcd_Set_X
Prototype
procedure SPI_Glcd_Set_X(x_pos : byte);
Returns
Nothing.
Sets x-axis position to x_pos dots from the left border of Glcd within the selected side.
Parameters :
Description
- x_pos: position on x-axis. Valid values: 0..63
Note: For side, x axis and page layout explanation see schematic at the bottom
of this page.
Requires
Glcd needs to be initialized for SPI communication, see SPI_Glcd_Init routines.
Example
SPI_Glcd_Set_X(25);
SPI_Glcd_Read_Data
Prototype
function SPI_Glcd_Read_Data() : byte;
Returns
One byte from Glcd memory.
Description
Reads data from the current location of Glcd memory and moves to the next
location.
Glcd needs to be initialized for SPI communication, see SPI_Glcd_Init routines.
Requires
Example
Glcd side, x-axis position and page should be set first. See the functions
SPI_Glcd_Set_Side, SPI_Glcd_Set_X, and SPI_Glcd_Set_Page.
var data : byte;
...
data := SPI_Glcd_Read_Data();
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
453
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Glcd_Write_Data
Prototype
procedure SPI_Glcd_Write_Data(ddata : byte);
Returns
Nothing.
Writes one byte to the current location in Glcd memory and moves to the next
location.
Description
Parameters :
- Ddata: data to be written
Glcd needs to be initialized for SPI communication, see SPI_Glcd_Init routines.
Requires
Example
Glcd side, x-axis position and page should be set first. See the functions
SPI_Glcd_Set_Side, SPI_Glcd_Set_X, and SPI_Glcd_Set_Page.
var ddata : byte;
...
SPI_Glcd_Write_Data(ddata);
SPI_Glcd_Fill
Prototype
procedure SPI_Glcd_Fill(pattern: byte);
Returns
Nothing.
Fills Glcd memory with byte pattern.
Parameters :
Description - pattern: byte to fill Glcd memory with
To clear the Glcd screen, use SPI_Glcd_Fill(0).
To fill the screen completely, use SPI_Glcd_Fill(0xFF).
454
Requires
Glcd needs to be initialized for SPI communication, see SPI_Glcd_Init routines.
Example
// Clear screen
SPI_Glcd_Fill(0);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Glcd_Dot
Prototype
procedure SPI_Glcd_Dot(x_pos : byte; y_pos : byte; color : byte);
Returns
Nothing.
Draws a dot on Glcd at coordinates (x_pos, y_pos).
Parameters :
- x_pos: x position. Valid values: 0..127
- y_pos: y position. Valid values: 0..63
Description
- color: color parameter. Valid values: 0..2
The parameter color determines the dot state: 0 clears dot, 1 puts a dot, and 2
inverts dot state.
Note: For x and y axis layout explanation see schematic at the bottom of this page.
Requires
Glcd needs to be initialized for SPI communication, see SPI_Glcd_Init routines.
Example
// Invert the dot in the upper left corner
SPI_Glcd_Dot(0, 0, 2);
SPI_Glcd_Line
Prototype
procedure SPI_Glcd_Line(x_start : integer; y_start : integer;
x_end : integer; y_end : integer; color : byte);
Returns
Nothing.
Draws a line on Glcd.
Parameters :
Description -
x_start: x coordinate of the line start. Valid values: 0..127
y_start: y coordinate of the line start. Valid values: 0..63
x_end: x coordinate of the line end. Valid values: 0..127
y_end: y coordinate of the line end. Valid values: 0..63
color: color parameter. Valid values: 0..2
Parameter color determines the line color: 0 white, 1 black, and 2 inverts each dot.
Requires
Glcd needs to be initialized for SPI communication, see SPI_Glcd_Init routines.
Example
// Draw a line between dots (0,0) and (20,30)
SPI_Glcd_Line(0, 0, 20, 30, 1);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
455
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Glcd_V_Line
Prototype
procedure SPI_Glcd_V_Line(y_start: byte; y_end: byte; x_pos:
byte; color: byte);
Returns
Nothing.
Draws a vertical line on Glcd.
Parameters :
Description
-
y_start: y coordinate of the line start. Valid values: 0..63
y_end: y coordinate of the line end. Valid values: 0..63
x_pos: x coordinate of vertical line. Valid values: 0..127
color: color parameter. Valid values: 0..2
Parameter color determines the line color: 0 white, 1 black, and 2 inverts each dot.
Requires
Glcd needs to be initialized for SPI communication, see SPI_Glcd_Init routines.
Example
// Draw a vertical line between dots (10,5) and (10,25)
SPI_Glcd_V_Line(5, 25, 10, 1);
SPI_Glcd_H_Line
Prototype
procedure SPI_Glcd_V_Line(x_start : byte; x_end : byte; y_pos :
byte; color : byte);
Returns
Nothing.
Draws a horizontal line on Glcd.
Parameters :
Description -
x_start: x coordinate of the line start. Valid values: 0..127
x_end: x coordinate of the line end. Valid values: 0..127
y_pos: y coordinate of horizontal line. Valid values: 0..63
color: color parameter. Valid values: 0..2
The parameter color determines the line color: 0 white, 1 black, and 2 inverts
each dot.
456
Requires
Glcd needs to be initialized for SPI communication, see SPI_Glcd_Init routines.
Example
// Draw a horizontal line between dots (10,20) and (50,20)
SPI_Glcd_H_Line(10, 50, 20, 1);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Glcd_Rectangle
Prototype
procedure SPI_Glcd_Rectangle(x_upper_left : byte; y_upper_left :
byte; x_bottom_right : byte; y_bottom_right : byte; color : byte);
Returns
Nothing.
Draws a rectangle on Glcd.
Parameters :
- x_upper_left: x coordinate of the upper left rectangle corner. Valid values: 0..127
- y_upper_left: y coordinate of the upper left rectangle corner. Valid values: 0..63
- x_bottom_right: x coordinate of the lower right rectangle corner. Valid
Description
values: 0..127
- y_bottom_right: y coordinate of the lower right rectangle corner. Valid
values: 0..63
- color: color parameter. Valid values: 0..2
The parameter color determines the color of the rectangle border: 0 white, 1
black, and 2 inverts each dot.
Requires
Glcd needs to be initialized for SPI communication, see SPI_Glcd_Init routines.
Example
// Draw a rectangle between dots (5,5) and (40,40)
SPI_Glcd_Rectangle(5, 5, 40, 40, 1);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
457
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Glcd_Box
Prototype
procedure SPI_Glcd_Box(x_upper_left : byte; y_upper_left : byte;
x_bottom_right : byte; y_bottom_right : byte; color : byte);
Returns
Nothing.
Draws a box on Glcd.
Parameters :
- x_upper_left: x coordinate of the upper left box corner. Valid values: 0..127
- y_upper_left: y coordinate of the upper left box corner. Valid values: 0..63
Description
- x_bottom_right: x coordinate of the lower right box corner. Valid values: 0..127
- y_bottom_right: y coordinate of the lower right box corner. Valid values: 0..63
- color: color parameter. Valid values: 0..2
The parameter color determines the color of the box fill: 0 white, 1 black, and 2
inverts each dot.
Requires
Glcd needs to be initialized for SPI communication, see SPI_Glcd_Init routines.
Example
// Draw a box between dots (5,15) and (20,40)
SPI_Glcd_Box(5, 15, 20, 40, 1);
SPI_Glcd_Circle
Prototype
procedure SPI_Glcd_Circle(x_center : integer; y_center : integer;
radius : integer; color : byte);
Returns
Nothing.
Draws a circle on Glcd.
Parameters :
Description -
x_center: x coordinate of the circle center. Valid values: 0..127
y_center: y coordinate of the circle center. Valid values: 0..63
radius: radius size
color: color parameter. Valid values: 0..2
The parameter color determines the color of the circle line: 0 white, 1 black, and
2 inverts each dot.
458
Requires
Glcd needs to be initialized for SPI communication, see SPI_Glcd_Init routine.
Example
// Draw a circle with center in (50,50) and radius=10
SPI_Glcd_Circle(50, 50, 10, 1);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Glcd_Set_Font
Prototype
procedure SPI_Glcd_Set_Font(activeFont : longint; aFontWidth :
byte; aFontHeight : byte; aFontOffs : word);
Returns
Nothing.
Sets font that will be used with SPI_Glcd_Write_Char and SPI_Glcd_Write_Text
routines.
Parameters :
Description -
activeFont: font to be set. Needs to be formatted as an array of char
aFontWidth: width of the font characters in dots.
aFontHeight: height of the font characters in dots.
aFontOffs: number that represents difference between the mikroPascal char
acter set and regular ASCII set (eg. if 'A' is 65 in ASCII character, and 'A' is 45
in the mikroPascal character set, aFontOffs is 20). Demo fonts supplied with
the library have an offset of 32, which means that they start with space.
The user can use fonts given in the file “__Lib_GLCD_fonts.mpas” file located in
the Uses folder or create his own fonts.
Requires
Glcd needs to be initialized for SPI communication, see SPI_Glcd_Init routines.
Example
// Use the custom 5x7 font "myfont" which starts with space (32):
SPI_Glcd_Set_Font(@myfont, 5, 7, 32);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
459
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Glcd_Write_Char
Prototype
procedure SPI_Glcd_Write_Char(chr1 : byte; x_pos : byte; page_num
: byte; color : byte);
Returns
Nothing.
Prints character on Glcd.
Parameters :
- chr1: character to be written
- x_pos: character starting position on x-axis. Valid values: 0..(127-FontWidth)
- page_num: the number of the page on which character will be written. Valid
Description
values: 0..7
- color: color parameter. Valid values: 0..2
The parameter color determines the color of the character: 0 white, 1 black,
and 2 inverts each dot.
Note: For x axis and page layout explanation see schematic at the bottom of
this page.
Glcd needs to be initialized for SPI communication, see SPI_Glcd_Init routines.
Requires
Example
460
Use the SPI_Glcd_Set_Font to specify the font for display; if no font is specified, then the default 5x8 font supplied with the library will be used.
// Write character 'C' on the position 10 inside the page 2:
SPI_Glcd_Write_Char("C", 10, 2, 1);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Glcd_Write_Text
Prototype
procedure SPI_Glcd_Write_Text(var text : array[40] of byte; x_pos
: byte; page_numb : byte; color : byte);
Returns
Nothing.
Prints text on Glcd.
Parameters :
- text: text to be written
- x_pos: text starting position on x-axis.
- page_num: the number of the page on which text will be written. Valid values: 0..7
Description
- color: color parameter. Valid values: 0..2
The parameter color determines the color of the text: 0 white, 1 black, and 2
inverts each dot.
Note: For x axis and page layout explanation see schematic at the bottom of
this page.
Glcd needs to be initialized for SPI communication, see SPI_Glcd_Init routines.
Requires
Example
Use the SPI_Glcd_Set_Font to specify the font for display; if no font is specified, then the default 5x8 font supplied with the library will be used.
// Write text "Hello world!" on the position 10 inside the page 2:
SPI_Glcd_Write_Text("Hello world!", 10, 2, 1);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
461
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Glcd_Image
Prototype
procedure SPI_Glcd_Image(const image : ^byte);
Returns
Nothing.
Displays bitmap on Glcd.
Parameters :
Description
- image: image to be displayed. Bitmap array can be located in both code and
RAM memory (due to the mikroPascal PRO for PIC pointer to const and
pointer to RAM equivalency).
Use the mikroPascal’s integrated Glcd Bitmap Editor (menu option Tools › Glcd
Bitmap Editor) to convert image to a constant array suitable for displaying on Glcd.
Requires
Glcd needs to be initialized for SPI communication, see SPI_Glcd_Init routines.
Example
// Draw image my_image on Glcd
SPI_Glcd_Image(my_image);
Library Example
The example demonstrates how to communicate to KS0108 Glcd via the SPI module, using serial to parallel convertor MCP23S17.
program SPI_Glcd;
uses bitmap;
// Port Expander module connections
var SPExpanderRST : sbit at RC0_bit;
SPExpanderCS : sbit at RC1_bit;
SPExpanderRST_Direction : sbit at TRISC0_bit;
SPExpanderCS_Direction : sbit at TRISC1_bit;
// End Port Expander module connections
var someText : array[20] of char;
counter : byte;
procedure Delay2S;
begin
Delay_ms(2000);
end;
begin
462
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
ANSEL := 0;
digital
ANSELH := 0;
C1ON_bit := 0;
C2ON_bit := 0;
Libraries
// Configure AN pins as
// Disable comparators
// If Port Expander Library uses SPI1 module
SPI1_Init();
// Initialize SPI module used with PortExpander
// // If Port Expander Library uses SPI2 module
// SPI2_Init(); // Initialize SPI module used with PortExpander
SPI_Glcd_Init(0);
SPI_Glcd_Fill(0x00);
// Initialize Glcd via SPI
// Clear Glcd
while (TRUE) do
begin
SPI_Glcd_Image(@truck_bmp);
Delay2s(); Delay2s();
// Draw image
SPI_Glcd_Fill(0x00);
Delay2s;
// Clear Glcd
SPI_Glcd_Box(62,40,124,63,1);
// Draw box
SPI_Glcd_Rectangle(5,5,84,35,1);
// Draw rectangle
SPI_Glcd_Line(0, 0, 127, 63, 1);
// Draw line
Delay2s();
counter := 5;
while (counter < 60) do // Draw horizontal and vertical line
begin
Delay_ms(250);
SPI_Glcd_V_Line(2, 54, counter, 1);
SPI_Glcd_H_Line(2, 120, counter, 1);
counter := counter + 5;
end;
Delay2s();
SPI_Glcd_Fill(0x00);
SPI_Glcd_Set_Font(@Character8x7, 8, 7, 32);
see __Lib_GLCDFonts.c in Uses folder
SPI_Glcd_Write_Text('mikroE', 1, 7, 2);
// Clear Glcd
// Choose font,
// Write string
for counter := 1 to 10 do// Draw circles
SPI_Glcd_Circle(63,32, 3*counter, 1);
Delay2s();
SPI_Glcd_Box(10,20, 70,63, 2);
Delay2s();
// Draw box
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
463
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Glcd_Fill(0xFF);
// Fill Glcd
SPI_Glcd_Set_Font(@Character8x7, 8, 7, 32);
someText := '8x7 Font';
SPI_Glcd_Write_Text(someText, 5, 0, 2);
Delay2s();
// Change font
SPI_Glcd_Set_Font(@System3x6, 3, 5, 32);
someText := '3X5 CAPITALS ONLY';
SPI_Glcd_Write_Text(someText, 60, 2, 2);
Delay2s();
// Change font
SPI_Glcd_Set_Font(@font5x7, 5, 7, 32);
someText := '5x7 Font';
SPI_Glcd_Write_Text(someText, 5, 4, 2);
Delay2s();
// Change font
// Write string
// Write string
// Write string
SPI_Glcd_Set_Font(@FontSystem5x7_v2, 5, 7, 32); // Change font
someText := '5x7 Font (v2)';
SPI_Glcd_Write_Text(someText, 50, 6, 2);
// Write string
Delay2s();
end;
end.
464
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
HW Connection
SPI Glcd HW connection
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
465
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI LCD LIBRARY
The mikroPascal PRO for PIC provides a library for communication with Lcd (with
HD44780 compliant controllers) in 4-bit mode via SPI interface.
For creating a custom set of Lcd characters use Lcd Custom Character Tool.
Note: The library uses the SPI module for communication. The user must initialize
the SPI module before using the SPI Lcd Library.
For MCUs with two SPI modules it is possible to initialize both of them and then
switch by using the SPI_Set_Active() routine.
Note: This Library is designed to work with the mikroElektronika's Serial Lcd
Adapter Board pinout. See schematic at the bottom of this page for details.
External dependencies of SPI Lcd Library
The implementation of SPI Lcd Library routines is based on Port Expander Library
routines.
External dependencies are the same as Port Expander Library external dependencies.
Library Routines
-
466
SPI_Lcd_Config
SPI_Lcd_Out
SPI_Lcd_Out_Cp
SPI_Lcd_Chr
SPI_Lcd_Chr_Cp
SPI_Lcd_Cmd
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Lcd_Config
Prototype
procedure SPI_Lcd_Config(DeviceAddress: byte);
Returns
Nothing.
Initializes the Lcd module via SPI interface.
Description
Parameters :
- DeviceAddress: spi expander hardware address, see schematic at the bottom
of this page
Global variables :
Requires
-
SPExpanderCS: Chip Select line
SPExpanderRST: Reset line
SPExpanderCS_Direction: Direction of the Chip Select pin
SPExpanderRST_Direction: Direction of the Reset pin
must be defined before using this function.
SPI module needs to be initialized. See SPI1_Init and SPI1_Init_Advanced routines.
// port expander pinout definition
var SPExpanderCS : sbit at RC1_bit;
SPExpanderRST : sbit at RC0_bit;
SPExpanderCS_Direction : sbit at TRISC1_bit;
SPExpanderRST_Direction : sbit at TRISC_bit;
Example
// If Port Expander Library uses SPI1 module
SPI1_Init();
// Initialize SPI module
used with PortExpander
SPI_Lcd_Config(0);
// initialize lcd over spi interface
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
467
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Lcd_Out
Prototype
procedure SPI_Lcd_Out(row: byte; column: byte; var text:
array[20] of byte);
Returns
Nothing.
Prints text on the Lcd starting from specified position. Both string variables and
literals can be passed as a text.
Description
Parameters :
- row: starting position row number
- column: starting position column number
- text: text to be written
Requires
Lcd needs to be initialized for SPI communication, see SPI_Lcd_Config routines.
Example
// Write text "Hello!" on Lcd starting from row 1, column 3:
SPI_Lcd_Out(1, 3, "Hello!");
SPI_Lcd_Out_CP
Prototype
procedure SPI_Lcd_Out_CP(var text : array[20] of byte);
Returns
Nothing.
Prints text on the Lcd at current cursor position. Both string variables and literals can be passed as a text.
Description
Parameters :
- text: text to be written
468
Requires
Lcd needs to be initialized for SPI communication, see SPI_Lcd_Config routines.
Example
// Write text "Here!" at current cursor position:
SPI_Lcd_Out_CP("Here!");
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Lcd_Chr
Prototype
procedure SPI_Lcd_Chr(Row : byte; Column : byte; Out_Char : byte);
Returns
Nothing.
Prints character on Lcd at specified position. Both variables and literals can be
passed as character.
Description
Parameters :
- Row: writing position row number
- Column: writing position column number
- Out_Char: character to be written
Requires
Lcd needs to be initialized for SPI communication, see SPI_Lcd_Config routines.
Example
// Write character "i" at row 2, column 3:
SPI_Lcd_Chr(2, 3, 'i');
SPI_Lcd_Chr_CP
Prototype
procedure SPI_Lcd_Chr_CP(Out_Char : byte);
Returns
Nothing.
Prints character on Lcd at current cursor position. Both variables and literals
can be passed as character.
Description
Parameters :
- Out_Char: character to be written
Requires
Lcd needs to be initialized for SPI communication, see SPI_Lcd_Config routines.
Example
// Write character "e" at current cursor position:
SPI_Lcd_Chr_CP('e');
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
469
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Lcd_Cmd
Prototype
procedure SPI_Lcd_Cmd(out_char : byte);
Returns
Nothing.
Sends command to Lcd.
Parameters :
Description
- out_char: command to be sent
Note: Predefined constants can be passed to the function, see Available Lcd
Commands.
Requires
Lcd needs to be initialized for SPI communication, see SPI_Lcd_Config routines.
Example
// Clear Lcd display:
SPI_Lcd_Cmd(_LCD_CLEAR);
Available SPI Lcd Commands
Lcd Command
Purpose
_LCD_FIRST_ROW
Move cursor to the 1st row
_LCD_SECOND_ROW
Move cursor to the 2nd row
_LCD_THIRD_ROW
Move cursor to the 3rd row
_LCD_FOURTH_ROW
Move cursor to the 4th row
_LCD_CLEAR
Clear display
_LCD_RETURN_HOME
Return cursor to home position, returns a shifted display to its original
position. Display data RAM is unaffected.
_LCD_CURSOR_OFF
Turn off cursor
_LCD_UNDERLINE_ON
Underline cursor on
_LCD_BLINK_CURSOR_ON
Blink cursor on
_LCD_MOVE_CURSOR_LEFT
Move cursor left without changing display data RAM
_LCD_MOVE_CURSOR_RIGHT Move cursor right without changing display data RAM
470
_LCD_TURN_ON
Turn Lcd display on
_LCD_TURN_OFF
Turn Lcd display off
_LCD_SHIFT_LEFT
Shift display left without changing display data RAM
_LCD_SHIFT_RIGHT
Shift display right without changing display data RAM
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Example
This example demonstrates how to communicate Lcd via the SPI module, using
serial to parallel convertor MCP23S17.
program SPI_Lcd;
var text : array[16] of char;
// Port Expander module connections
var SPExpanderRST : sbit at RC0_bit;
SPExpanderCS : sbit at RC1_bit;
SPExpanderRST_Direction : sbit at TRISC0_bit;
SPExpanderCS_Direction : sbit at TRISC1_bit;
// End Port Expander module connections
begin
text := 'mikroElektronika';
// If Port Expander Library uses SPI1 module
SPI1_Init();
// Initialize SPI module used with PortExpander
// If Port Expander Library uses SPI2 module
// SPI2_Init();
// Initialize SPI module used with PortExpander
SPI_Lcd_Config(0);
// Initialize Lcd over
SPI interface
SPI_Lcd_Cmd(_LCD_CLEAR);
// Clear display
SPI_Lcd_Cmd(_LCD_CURSOR_OFF);
// Turn cursor off
SPI_Lcd_Out(1,6, 'mikroE');
// Print text to Lcd,
1st row, 6th column
SPI_Lcd_Chr_CP('!');
// Append '!'
SPI_Lcd_Out(2,1, text);
// Print text to Lcd,
2nd row, 1st column
end.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
471
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
HW Connection
SPI Lcd HW connection
472
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI LCD8 (8-BIT INTERFACE) LIBRARY
The mikroPascal PRO for PIC provides a library for communication with Lcd (with
HD44780 compliant controllers) in 8-bit mode via SPI interface.
For creating a custom set of Lcd characters use Lcd Custom Character Tool.
Note: Library uses the SPI module for communication. The user must initialize the
SPI module before using the SPI Lcd Library.
For MCUs with two SPI modules it is possible to initialize both of them and then
switch by using the SPI_Set_Active() routine.
Note: This Library is designed to work with mikroElektronika's Serial Lcd/Glcd
Adapter Board pinout, see schematic at the bottom of this page for details.
External dependencies of SPI Lcd Library
The implementation of SPI Lcd Library routines is based on Port Expander Library
routines.
External dependencies are the same as Port Expander Library external dependencies.
Library Routines
-
SPI_Lcd8_Config
SPI_Lcd8_Out
SPI_Lcd8_Out_CP
SPI_Lcd8_Chr
SPI_Lcd8_Chr_CP
SPI_Lcd8_Cmd
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
473
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Lcd8_Config
Prototype
procedure SPI_Lcd8_Config(DeviceAddress : byte);
Returns
Nothing.
Initializes the Lcd module via SPI interface.
Description
Parameters :
- DeviceAddress: spi expander hardware address, see schematic at the
bottom of this page
Global variables :
Requires
-
SPExpanderCS: Chip Select line
SPExpanderRST: Reset line
SPExpanderCS_Direction: Direction of the Chip Select pin
SPExpanderRST_Direction: Direction of the Reset pin
must be defined before using this function.
SPI module needs to be initialized. See SPI1_Init and SPI1_Init_Advanced routines.
Example
// port expander pinout definition
var SPExpanderCS : sbit at RC1_bit;
SPExpanderRST : sbit at RC0_bit;
SPExpanderCS_Direction : sbit at TRISC1_bit;
SPExpanderRST_Direction : sbit at TRISC_bit;
SPI1_Init();
PortExpander
...
SPI_Lcd8_Config(0);
474
// Initialize SPI module used with
// intialize lcd in 8bit mode via spi
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Lcd8_Out
Prototype
procedure SPI_Lcd8_Out(row: byte; column: byte; var text:
array[20] of byte);
Returns
Nothing.
Prints text on Lcd starting from specified position. Both string variables and literals can be passed as a text.
Description
Parameters :
- row: starting position row number
- column: starting position column number
- text: text to be written
Requires
Lcd needs to be initialized for SPI communication, see SPI_Lcd8_Config routines.
Example
// Write text "Hello!" on Lcd starting from row 1, column 3:
SPI_Lcd8_Out(1, 3, "Hello!");
SPI_Lcd8_Out_CP
Prototype
procedure SPI_Lcd8_Out_CP(var text : array[20] of byte);
Returns
Nothing.
Prints text on Lcd at current cursor position. Both string variables and literals
can be passed as a text.
Description
Parameters :
- text: text to be written
Requires
Lcd needs to be initialized for SPI communication, see SPI_Lcd8_Config routines.
Example
// Write text "Here!" at current cursor position:
SPI_Lcd8_Out_CP("Here!");
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
475
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Lcd8_Chr
Prototype
procedure SPI_Lcd8_Chr(Row : byte; Column : byte; Out_Char : byte);
Returns
Nothing.
Prints character on Lcd at specified position. Both variables and literals can be
passed as character.
Description
Parameters :
- row: writing position row number
- column: writing position column number
- out_char: character to be written
Requires
Lcd needs to be initialized for SPI communication, see SPI_Lcd8_Config routines.
Example
// Write character "i" at row 2, column 3:
SPI_Lcd8_Chr(2, 3, 'i');
SPI_Lcd8_Chr_CP
Prototype
procedure SPI_Lcd8_Chr_CP(Out_Char : byte);
Returns
Nothing.
Prints character on Lcd at current cursor position. Both variables and literals
can be passed as character.
Description
Parameters :
- out_char : character to be written
Requires
Lcd needs to be initialized for SPI communication, see SPI_Lcd8_Config routines.
Print “e” at current cursor position:
Example
476
// Write character "e" at current cursor position:
SPI_Lcd8_Chr_CP('e');
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_Lcd8_Cmd
Prototype
procedure SPI_Lcd8_Cmd(out_char : byte);
Returns
Nothing.
Sends command to Lcd.
Parameters :
Description
- out_char: command to be sent
Note: Predefined constants can be passed to the function, see Available Lcd
Commands.
Requires
Lcd needs to be initialized for SPI communication, see SPI_Lcd8_Config routines.
Example
// Clear Lcd display:
SPI_Lcd8_Cmd(_LCD_CLEAR);
Available SPI Lcd8 Commands
Lcd Command
Purpose
_LCD_FIRST_ROW
Move cursor to the 1st row
_LCD_SECOND_ROW
Move cursor to the 2nd row
_LCD_THIRD_ROW
Move cursor to the 3rd row
_LCD_FOURTH_ROW
Move cursor to the 4th row
_LCD_CLEAR
Clear display
_LCD_RETURN_HOME
Return cursor to home position, returns a shifted display to its original
position. Display data RAM is unaffected.
_LCD_CURSOR_OFF
Turn off cursor
_LCD_UNDERLINE_ON
Underline cursor on
_LCD_BLINK_CURSOR_ON
Blink cursor on
_LCD_MOVE_CURSOR_LEFT
Move cursor left without changing display data RAM
_LCD_MOVE_CURSOR_RIGHT Move cursor right without changing display data RAM
_LCD_TURN_ON
Turn Lcd display on
_LCD_TURN_OFF
Turn Lcd display off
_LCD_SHIFT_LEFT
Shift display left without changing display data RAM
_LCD_SHIFT_RIGHT
Shift display right without changing display data RAM
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
477
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Example
This example demonstrates how to communicate Lcd in 8-bit mode via the SPI module, using serial to parallel convertor MCP23S17.
program Spi_Lcd8_Test;
var text : array[16] of char;
// Port Expander module connections
var SPExpanderRST : sbit at RC0_bit;
SPExpanderCS : sbit at RC1_bit;
SPExpanderRST_Direction : sbit at TRISC0_bit;
SPExpanderCS_Direction : sbit at TRISC1_bit;
// End Port Expander module connections
begin
text := 'mikroE';
// If Port Expander Library uses SPI1 module
SPI1_Init();
module used with PortExpander
// Initialize SPI
// // If Port Expander Library uses SPI2 module
// SPI2_Init();
// Initialize SPI
module used with PortExpander
SPI_Lcd8_Config(0);
8bit mode via SPI
SPI_Lcd8_Cmd(_LCD_CLEAR);
SPI_Lcd8_Cmd(_LCD_CURSOR_OFF);
SPI_Lcd8_Out(1,6, text);
1st row, 6th column...
SPI_Lcd8_Chr_CP('!');
SPI_Lcd8_Out(2,1, 'mikroelektronika');
2nd row, 1st column...
SPI_Lcd8_Out(3,1, text);
with more than two rows
SPI_Lcd8_Out(4,15, text);
with more than two rows
end.
478
// Intialize Lcd in
// Clear display
// Turn cursor off
// Print text to Lcd,
// Append '!'
// Print text to Lcd,
// For Lcd modules
// For Lcd modules
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
HW Connection
SPI LCD8 HW connection
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
479
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI T6963C GRAPHIC LCD LIBRARY
The mikroPascal PRO for PIC provides a library for working with GLCDs based on
TOSHIBA T6963C controller via SPI interface. The Toshiba T6963C is a very popular Lcd controller for the use in small graphics modules. It is capable of controlling
displays with a resolution up to 240x128. Because of its low power and small outline it is most suitable for mobile applications such as PDAs, MP3 players or mobile
measurement equipment. Although this controller is small, it has a capability of displaying and merging text and graphics and it manages all interfacing signals to the
displays Row and Column drivers.
For creating a custom set of Glcd images use Glcd Bitmap Editor Tool.
Note: The library uses the SPI module for communication. The user must initialize
SPI module before using the SPI T6963C Glcd Library.
For MCUs with two SPI modules it is possible to initialize both of them and then
switch by using the SPI_Set_Active() routine.
Note: This Library is designed to work with mikroElektronika's Serial Glcd 240x128
and 240x64 Adapter Boards pinout, see schematic at the bottom of this page for
details.
Note: Some mikroElektronika's adapter boards have pinout different from T6369C
datasheets. Appropriate relations between these labels are given in the table below:
Adapter Board T6369C datasheet
RS
C/D
R/W
/RD
E
/WR
External dependencies of SPI T6963C Graphic Lcd Library
The implementation of SPI T6963C Graphic Lcd Library routines is based on Port
Expander Library routines.
External dependencies are the same as Port Expander Library external dependencies.
480
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Routines
-
SPI_T6963C_Config
SPI_T6963C_WriteData
SPI_T6963C_WriteCommand
SPI_T6963C_SetPtr
SPI_T6963C_WaitReady
SPI_T6963C_Fill
SPI_T6963C_Dot
SPI_T6963C_Write_Char
SPI_T6963C_Write_Text
SPI_T6963C_Line
SPI_T6963C_Rectangle
SPI_T6963C_Box
SPI_T6963C_Circle
SPI_T6963C_Image
SPI_T6963C_Sprite
SPI_T6963C_Set_Cursor
SPI_T6963C_ClearBit
SPI_T6963C_SetBit
SPI_T6963C_NegBit
SPI_T6963C_DisplayGrPanel
SPI_T6963C_DisplayTxtPanel
SPI_T6963C_SetGrPanel
SPI_T6963C_SetTxtPanel
SPI_T6963C_PanelFill
SPI_T6963C_GrFill
SPI_T6963C_TxtFill
SPI_T6963C_Cursor_Height
SPI_T6963C_Graphics
SPI_T6963C_Text
SPI_T6963C_Cursor
SPI_T6963C_Cursor_Blink
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
481
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_T6963C_Config
Prototype
procedure SPI_T6963C_Config(width : word; height : byte; fntW :
byte; DeviceAddress : byte; wr : byte; rd : byte; cd : byte; rst
: byte);
Returns
Nothing.
Initializes T6963C Graphic Lcd controller.
Parameters :
-
width: width of the Glcd panel
height: height of the Glcd panel
fntW: font width
DeviceAddress: SPI expander hardware address, see schematic at the
-
bottom of this page
wr: write signal pin on Glcd control port
rd: read signal pin on Glcd control port
cd: command/data signal pin on Glcd control port
rst: reset signal pin on Glcd control port
Display RAM organization:
The library cuts RAM into panels : a complete panel is one graphics panel followed by a text panel (see schematic below).
Description
schematic:
+---------------------+ /\
+ GRAPHICS PANEL #0
+ |
+
+ |
+
+ |
+
+ |
+---------------------+ | PANEL 0
+ TEXT PANEL #0
+ |
+
+ \/
+---------------------+ /\
+ GRAPHICS PANEL #1
+ |
+
+ |
+
+ |
+
+ |
+---------------------+ | PANEL 1
+ TEXT PANEL #1
+ |
+
+ |
+---------------------+ \/
482
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Global variables :
Requires
- SPExpanderCS: Chip Select line
- SPExpanderRST: Reset line
- SPExpanderCS_Direction: Direction of the Chip Select pin
- SPExpanderRST_Direction: Direction of the Reset pin
must be defined before using this function.
SPI module needs to be initialized. See SPI1_Init and SPI1_Init_Advanced routines.
Example
// port expander pinout definition
var SPExpanderCS : sbit at RC1_bit;
SPExpanderRST : sbit at RC0_bit;
SPExpanderCS_Direction : sbit at TRISC1_bit;
SPExpanderRST_Direction : sbit at TRISC_bit;
...
// Initialize SPI module
SPI1_Init();
SPI_T6963C_Config(240, 64, 8, 0, 0, 1, 3, 4);
SPI_T6963C_WriteData
Prototype
procedure SPI_T6963C_WriteData(Ddata : byte);
Returns
Nothing.
Writes data to T6963C controller via SPI interface.
Description Parameters :
- Ddata: data to be written
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
SPI_T6963C_WriteData(AddrL);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
483
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_T6963C_WriteCommand
Prototype
procedure SPI_T6963C_WriteCommand(Ddata : byte);
Returns
Nothing.
Writes command to T6963C controller via SPI interface.
Description Parameters :
- Ddata: command to be written
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
SPI_T6963C_WriteCommand(SPI_T6963C_CURSOR_POINTER_SET);
SPI_T6963C_SetPtr
Prototype
procedure SPI_T6963C_SetPtr(p : word; c : byte);
Returns
Nothing.
Sets the memory pointer p for command c.
Description
Parameters :
- p: address where command should be written
- c: command to be written
Requires
SToshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
SPI_T6963C_SetPtr(T6963C_grHomeAddr + start,
T6963C_ADDRESS_POINTER_SET);
SPI_T6963C_WaitReady
Prototype
procedure SPI_T6963C_WaitReady();
Returns
Nothing.
Description Pools the status byte, and loops until Toshiba Glcd module is ready.
484
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
SPI_T6963C_WaitReady();
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_T6963C_Fill
Prototype
procedure SPI_T6963C_Fill(v : byte; start : word; len : word);
Returns
Nothing.
Fills controller memory block with given byte.
Parameters :
Description
- v: byte to be written
- start: starting address of the memory block
- len: length of the memory block in bytes
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
SPI_T6963C_Fill(0x33; 0x00FF; 0x000F);
SPI_T6963C_Dot
Prototype
procedure SPI_T6963C_Dot(x : integer; y : integer; color : byte);
Returns
Nothing.
Draws a dot in the current graphic panel of Glcd at coordinates (x, y).
Parameters :
Description
- x: dot position on x-axis
- y: dot position on y-axis
- color: color parameter. Valid values: SPI_T6963C_BLACK and
SPI_T6963C_WHITE
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
SPI_T6963C_Dot(x0, y0, pcolor);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
485
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_T6963C_Write_Char
Prototype
procedure SPI_T6963C_Write_Char(c : byte; x : byte; y : byte;
mode : byte);
Returns
Nothing.
Writes a char in the current text panel of Glcd at coordinates (x, y).
Parameters :
-
c: char to be written
x: char position on x-axis
y: char position on y-axis
mode: mode parameter. Valid values: SPI_T6963C_ROM_MODE_OR,
SPI_T6963C_ROM_MODE_XOR, SPI_T6963C_ROM_MODE_AND and
SPI_T6963C_ROM_MODE_TEXT
Mode parameter explanation:
Description
- OR Mode: In the OR-Mode, text and graphics can be displayed and the data
is logically “OR-ed”. This is the most common way of combining text and
graphics for example labels on buttons.
- XOR-Mode: In this mode, the text and graphics data are combined via the
logical “exclusive OR”. This can be useful to display text in negative mode, i.e.
white text on black background.
- AND-Mode: The text and graphic data shown on display are combined via the
logical “AND function”.
- TEXT-Mode: This option is only available when displaying just a text. The Text
Attribute values are stored in the graphic area of display memory.
For more details see the T6963C datasheet.
486
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
SPI_T6963C_Write_Char("A",22,23,AND);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_T6963C_Write_Text
Prototype
procedure SPI_T6963C_write_text(var str : array[10] of byte; x,
y, mode : byte);
Returns
Nothing.
Writes text in the current text panel of Glcd at coordinates (x, y).
Parameters :
-
str: text to be written
x: text position on x-axis
y: text position on y-axis
mode: mode parameter. Valid values: SPI_T6963C_ROM_MODE_OR,
SPI_T6963C_ROM_MODE_XOR, SPI_T6963C_ROM_MODE_AND and
SPI_T6963C_ROM_MODE_TEXT
Mode parameter explanation:
Description
- OR Mode: In the OR-Mode, text and graphics can be displayed and the data
is logically “OR-ed”. This is the most common way of combining text and
graphics for example labels on buttons.
- XOR-Mode: In this mode, the text and graphics data are combined via the
logical “exclusive OR”. This can be useful to display text in negative mode, i.e.
white text on black background.
- AND-Mode: The text and graphic data shown on the display are combined via
the logical “AND function”.
- TEXT-Mode: This option is only available when displaying just a text. The Text
Attribute values are stored in the graphic area of display memory.
For more details see the T6963C datasheet.
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
SPI_T6963C_Write_Text('Glcd LIBRARY DEMO, WELCOME !', 0, 0,
T6963C_ROM_MODE_EXOR);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
487
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_T6963C_Line
Prototype
procedure SPI_T6963C_Line(x0 : integer; y0 : integer; x1 : integer; y1 : integer; pcolor : byte);
Returns
Nothing.
Draws a line from (x0, y0) to (x1, y1).
Parameters :
Description
-
x0: x coordinate of the line start
y0: y coordinate of the line end
x1: x coordinate of the line start
y1: y coordinate of the line end
pcolor: color parameter. Valid values: SPI_T6963C_BLACK and
SPI_T6963C_WHITE
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
SPI_T6963C_Line(0, 0, 239, 127, T6963C_WHITE);
SPI_T6963C_Rectangle
Prototype
procedure SPI_T6963C_Rectangle(x0 : integer; y0 : integer; x1 :
integer; y1 : integer; pcolor : byte);
Returns
Nothing.
Draws a rectangle on Glcd.
Parameters :
Description
-
x0: x coordinate of the upper left rectangle corner
y0: y coordinate of the upper left rectangle corner
x1: x coordinate of the lower right rectangle corner
y1: y coordinate of the lower right rectangle corner
pcolor: color parameter. Valid values: SPI_T6963C_BLACK and
SPI_T6963C_WHITE
488
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
SPI_T6963C_Rectangle(20, 20, 219, 107, T6963C_WHITE);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_T6963C_Box
Prototype
procedure SPI_T6963C_Box(x0 : integer; y0 : integer; x1 : integer; y1 : integer; pcolor : byte);
Returns
Nothing.
Draws a box on the Glcd
Parameters :
Description
-
x0: x coordinate of the upper left box corner
y0: y coordinate of the upper left box corner
x1: x coordinate of the lower right box corner
y1: y coordinate of the lower right box corner
pcolor: color parameter. Valid values: SPI_T6963C_BLACK and
SPI_T6963C_WHITE
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
SPI_T6963C_Box(0, 119, 239, 127, T6963C_WHITE);
SPI_T6963C_Circle
Prototype
procedure SPI_T6963C_Circle(x : integer; y : integer; r :
longint; pcolor : word);
Returns
Nothing.
Draws a circle on the Glcd.
Parameters :
Description -
x: x coordinate of the circle center
y: y coordinate of the circle center
r: radius size
pcolor: color parameter. Valid values: SPI_T6963C_BLACK and
SPI_T6963C_WHITE
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
SPI_T6963C_Circle(120, 64, 110, T6963C_WHITE);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
489
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_T6963C_Image
Prototype
procedure SPI_T6963C_image(const pic : ^byte);
Returns
Nothing.
Displays bitmap on Glcd.
Parameters :
- pic: image to be displayed. Bitmap array can be located in both code and
RAM memory (due to the mikroPascal PRO for PIC pointer to const and
Description
pointer to RAM equivalency).
Use the mikroPascal’s integrated Glcd Bitmap Editor (menu option Tools › Glcd
Bitmap Editor) to convert image to a constant array suitable for displaying on
Glcd.
Note: Image dimension must match the display dimension.
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
SPI_T6963C_Image(my_image);
SPI_T6963C_Sprite
Prototype
procedure SPI_T6963C_sprite(px, py : byte; const pic : ^byte; sx,
sy : byte);
Returns
Nothing.
Fills graphic rectangle area (px, py) to (px+sx, py+sy) with custom size picture.
Parameters :
- px: x coordinate of the upper left picture corner. Valid values: multiples of the
font width
Description - py: y coordinate of the upper left picture corner
- pic: picture to be displayed
- sx: picture width. Valid values: multiples of the font width
- sy: picture height
Note: If px and sx parameters are not multiples of the font width they will be
scaled to the nearest lower number that is a multiple of the font width.
490
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
SPI_T6963C_Sprite(76, 4, einstein, 88, 119); // draw a sprite
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_T6963C_Set_Cursor
Prototype
procedure SPI_T6963C_set_cursor(x, y : byte);
Returns
Nothing.
Sets cursor to row x and column y.
Description
Parameters :
- x: cursor position row number
- y: cursor position column number
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
SPI_T6963C_Set_Cursor(cposx, cposy);
SPI_T6963C_ClearBit
Prototype
procedure SPI_T6963C_clearBit(b : byte);
Returns
Nothing.
Clears control port bit(s).
Description Parameters :
- b: bit mask. The function will clear bit x on control port if bit x in bit mask is set to 1.
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
// clear bits 0 and 1 on control port
SPI_T6963C_ClearBit(0x03);
SPI_T6963C_SetBit
Prototype
procedure SPI_T6963C_setBit(b : byte);
Returns
Nothing.
Sets control port bit(s).
Description Parameters :
- b: bit mask. The function will set bit x on control port if bit x in bit mask is set to 1.
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
// set bits 0 and 1 on control port
SPI_T6963C_SetBit(0x03);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
491
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_T6963C_NegBit
Prototype
procedure SPI_T6963C_negBit(b : byte);
Returns
Nothing.
Negates control port bit(s).
Description
Parameters :
- b: bit mask. The function will negate bit x on control port if bit x in bit mask is
set to 1.
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
// negate bits 0 and 1 on control port
SPI_T6963C_NegBit(0x03);
SPI_T6963C_DisplayGrPanel
Prototype
procedure SPI_T6963C_DisplayGrPanel(n : byte);
Returns
Nothing.
Display selected graphic panel.
Description Parameters :
- n: graphic panel number. Valid values: 0 and 1.
492
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
// display graphic panel 1
SPI_T6963C_DisplayGrPanel(1);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_T6963C_DisplayTxtPanel
Prototype
procedure SPI_T6963C_DisplayGrPanel(n : byte);
Returns
Nothing.
Display selected graphic panel.
Description Parameters :
- n: graphic panel number. Valid values: 0 and 1.
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
// display graphic panel 1
SPI_T6963C_DisplayGrPanel(1);
SPI_T6963C_SetGrPanel
Prototype
procedure SPI_T6963C_SetGrPanel(n : byte);
Returns
Nothing.
Compute start address for selected graphic panel and set appropriate internal pointers. All subsequent graphic operations will be preformed at this graphic panel.
Description
Parameters :
- n: graphic panel number. Valid values: 0 and 1.
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
// set graphic panel 1 as current graphic panel.
SPI_T6963C_SetGrPanel(1);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
493
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_T6963C_SetTxtPanel
Prototype
procedure SPI_T6963C_SetTxtPanel(n : byte);
Returns
Nothing.
Compute start address for selected text panel and set appropriate internal pointers. All subsequent text operations will be preformed at this text panel.
Description
Parameters :
- n: text panel number. Valid values: 0 and 1.
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
// set text panel 1 as current text panel.
SPI_T6963C_SetTxtPanel(1);
SPI_T6963C_PanelFill
Prototype
procedure SPI_T6963C_PanelFill(v : byte);
Returns
Nothing.
Fill current panel in full (graphic+text) with appropriate value (0 to clear).
Description Parameters :
- v: value to fill panel with.
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
clear current panel
SPI_T6963C_PanelFill(0);
SPI_T6963C_GrFill
Prototype
procedure SPI_T6963C_GrFill(v : byte);
Returns
Nothing.
Fill current graphic panel with appropriate value (0 to clear).
Description Parameters :
- v: value to fill graphic panel with.
494
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
// clear current graphic panel
SPI_T6963C_GrFill(0);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_T6963C_TxtFill
Prototype
procedure SPI_T6963C_TxtFill(v : byte);
Returns
Nothing.
Fill current text panel with appropriate value (0 to clear).
Description Parameters :
- v: this value increased by 32 will be used to fill text panel.
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
// clear current text panel
SPI_T6963C_TxtFill(0);
SPI_T6963C_Cursor_Height
Prototype
procedure SPI_T6963C_Cursor_Height(n : byte);
Returns
Nothing.
Set cursor size.
Description Parameters :
- n: cursor height. Valid values: 0..7.
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
SPI_T6963C_Cursor_Height(7);
SPI_T6963C_Graphics
Prototype
procedure SPI_T6963C_Graphics(n : byte);
Returns
Nothing.
Enable/disable graphic displaying.
Description
Parameters :
- n: graphic enable/disable parameter. Valid values: 0 (disable graphic
dispaying) and 1 (enable graphic displaying).
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
// enable graphic displaying
SPI_T6963C_Graphics(1);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
495
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
SPI_T6963C_Text
Prototype
procedure SPI_T6963C_Text(n : byte);
Returns
Nothing.
Enable/disable text displaying.
Description
Parameters :
- n: text enable/disable parameter. Valid values: 0 (disable text dispaying) and 1
(enable text displaying).
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
// enable text displaying
SPI_T6963C_Text(1);
SPI_T6963C_Cursor
Prototype
procedure SPI_T6963C_Cursor(n : byte);
Returns
Nothing.
Set cursor on/off.
Description Parameters :
- n: on/off parameter. Valid values: 0 (set cursor off) and 1 (set cursor on).
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
// set cursor on
SPI_T6963C_Cursor(1);
SPI_T6963C_Cursor_Blink
Prototype
procedure SPI_T6963C_Cursor_Blink(n : byte);
Returns
Nothing.
Enable/disable cursor blinking.
Description
Parameters :
- n: cursor blinking enable/disable parameter. Valid values: 0 (disable cursor
blinking) and 1 (enable cursor blinking).
496
Requires
Toshiba Glcd module needs to be initialized. See SPI_T6963C_Config routine.
Example
// enable cursor blinking
SPI_T6963C_Cursor_Blink(1);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Example
The following drawing demo tests advanced routines of the SPI T6963C Glcd library.
Hardware configurations in this example are made for the T6963C 240x128 display,
EasyPIC5 board and 16F887.
program SPI_T6963C_240x128;
uses __Lib_SPIT6963C_Const, bitmap, bitmap2;
var
// Port Expander module connections
SPExpanderRST : sbit at RC0_bit;
SPExpanderCS : sbit at RC1_bit;
SPExpanderRST_Direction : sbit at TRISC0_bit;
SPExpanderCS_Direction : sbit at TRISC1_bit;
// End Port Expander module connections
var
panel : byte;
// current panel
i : word;
// general purpose register
curs : byte;
// cursor visibility
cposx,
cposy : word;
// cursor x-y position
txt, txt1 : string[29];
begin
txt1 := ' EINSTEIN WOULD HAVE LIKED mE';
txt := ' GLCD LIBRARY DEMO, WELCOME !';
ANSEL := 0;
ANSELH := 0;
C1ON_bit := 0;
C2ON_bit := 0;
TRISB0_bit
TRISB1_bit
TRISB2_bit
TRISB3_bit
TRISB4_bit
:=
:=
:=
:=
:=
// Configure AN pins as digital I/O
// Disable comparators
1;
1;
1;
1;
1;
//
//
//
//
//
Set
Set
Set
Set
Set
RB0
RB1
RB2
RB3
RB4
as
as
as
as
as
input
input
input
input
input
// Initialize SPI module
SPI1_Init();
// // If Port Expander Library uses SPI2 module
// Pass pointer to SPI Read function of used SPI module
// Initialize SPI module used with PortExpander
//
SPI2_Init_Advanced(_SPI_MASTER,
_SPI_CLK_HI_TRAILING);
_SPI_FCY_DIV32,
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
497
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
{*
* init display for 240 pixel width and 128 pixel height
* 8 bits character width
* data bus on MCP23S17 portB
* control bus on MCP23S17 portA
* bit 2 is !WR
* bit 1 is !RD
* bit 0 is !CD
* bit 4 is RST
* chip enable, reverse on, 8x8 font internaly set in library
*}
// Initialize SPI Toshiba 240x128
SPI_T6963C_Config(240, 128, 8, 0, 2, 1, 0, 4) ;
//Delay_ms(1000);
{*
* Enable both graphics and text display at the same time
*}
SPI_T6963C_graphics(1) ;
SPI_T6963C_text(1) ;
panel := 0 ;
i := 0 ;
curs := 0 ;
cposx := 0;
cposy := 0 ;
{*
* Text messages
*}
SPI_T6963C_write_text(txt, 0, 0, SPI_T6963C_ROM_MODE_XOR) ;
SPI_T6963C_write_text(txt1, 0, 15, SPI_T6963C_ROM_MODE_XOR) ;
{*
* Cursor
*}
SPI_T6963C_cursor_height(8) ;
SPI_T6963C_set_cursor(0, 0) ;
SPI_T6963C_cursor(0) ;
// 8 pixel height
// move cursor to top left
// cursor off
{*
* Draw rectangles
*}
SPI_T6963C_rectangle(0, 0, 239, 127, SPI_T6963C_WHITE) ;
SPI_T6963C_rectangle(20, 20, 219, 107, SPI_T6963C_WHITE) ;
SPI_T6963C_rectangle(40, 40, 199, 87, SPI_T6963C_WHITE) ;
SPI_T6963C_rectangle(60, 60, 179, 67, SPI_T6963C_WHITE) ;
498
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
{*
* Draw a cross
*}
SPI_T6963C_line(0, 0, 239, 127, SPI_T6963C_WHITE) ;
SPI_T6963C_line(0, 127, 239, 0, SPI_T6963C_WHITE) ;
{*
* Draw solid boxes
*}
SPI_T6963C_box(0, 0, 239, 8, SPI_T6963C_WHITE) ;
SPI_T6963C_box(0, 119, 239, 127, SPI_T6963C_WHITE) ;
{*
* Draw circles
*}
SPI_T6963C_circle(120,
SPI_T6963C_circle(120,
SPI_T6963C_circle(120,
SPI_T6963C_circle(120,
SPI_T6963C_circle(120,
SPI_T6963C_circle(120,
SPI_T6963C_circle(120,
64,
64,
64,
64,
64,
64,
64,
10,
30,
50,
70,
90,
110,
130,
SPI_T6963C_WHITE)
SPI_T6963C_WHITE)
SPI_T6963C_WHITE)
SPI_T6963C_WHITE)
SPI_T6963C_WHITE)
SPI_T6963C_WHITE)
SPI_T6963C_WHITE)
SPI_T6963C_sprite(76, 4, @einstein, 88, 119) ;
SPI_T6963C_setGrPanel(1) ;
;
;
;
;
;
;
;
// Draw a sprite
// Select other graphic panel
SPI_T6963C_sprite(0, 0, @me, 240, 64);
// 240x128 can't
be stored in most of PIC16 MCUs
SPI_T6963C_sprite(0, 64, @me, 240, 64);
//
it is replaced
with smaller picture 240x64
//
Smaller picture is drawn two times
while (TRUE) do
begin
// Endless loop
{*
* If PORTA_0 is pressed, toggle the display between graphic
panel 0 and graphic 1
*}
if( RB0_bit <> 0) then
begin
Inc(panel) ;
panel := panel and 1;
SPI_T6963C_setPtr((SPI_T6963C_grMemSize
+
SPI_T6963C_txtMemSize) * panel, SPI_T6963C_GRAPHIC_HOME_ADDRESS_SET)
;
Delay_ms(300) ;
end
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
499
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
{*
* If PORTA_1 is pressed, display only graphic panel
*}
else
if ( RB1_bit <> 0) then
begin
SPI_T6963C_graphics(1) ;
SPI_T6963C_text(0) ;
Delay_ms(300) ;
end
{*
* If PORTA_2 is pressed, display only text panel
*}
else
if ( RB2_bit <> 0) then
begin
SPI_T6963C_graphics(0) ;
SPI_T6963C_text(1) ;
Delay_ms(300) ;
end
{*
* If PORTA_3 is pressed, display text and graphic panels
*}
else
if ( RB3_bit <> 0) then
begin
SPI_T6963C_graphics(1) ;
SPI_T6963C_text(1) ;
Delay_ms(300) ;
end
{*
* If PORTA_4 is pressed, change cursor
*}
else
if( RB4_bit <> 0) then
begin
Inc(curs);
if (curs = 3) then
curs := 0;
case curs of
0:
// no cursor
SPI_T6963C_cursor(0) ;
500
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
1: begin
// blinking cursor
SPI_T6963C_cursor(1) ;
SPI_T6963C_cursor_blink(1) ;
end;
2: begin
// non blinking cursor
SPI_T6963C_cursor(1) ;
SPI_T6963C_cursor_blink(0) ;
end;
end;
Delay_ms(300) ;
end;
{*
* Move cursor, even if not visible
*}
Inc(cposx);
if (cposx = SPI_T6963C_txtCols) then
begin
cposx := 0 ;
Inc(cposy);
if
(cposy
=
SPI_T6963C_grHeight
SPI_T6963C_CHARACTER_HEIGHT) then
cposy := 0 ;
end;
SPI_T6963C_set_cursor(cposx, cposy) ;
/
Delay_ms(100) ;
end;
end.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
501
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
HW Connection
SPI T6963C Glcd HW connection
502
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
T6963C GRAPHIC LCD LIBRARY
The mikroPascal PRO for PIC provides a library for working with GLCDs based on
TOSHIBA T6963C controller. The Toshiba T6963C is a very popular Lcd controller
for the use in small graphics modules. It is capable of controlling displays with a resolution up to 240x128. Because of its low power and small outline it is most suitable
for mobile applications such as PDAs, MP3 players or mobile measurement equipment. Although small, this contoller has a capability of displaying and merging text
and graphics and it manages all the interfacing signals to the displays Row and Column drivers.
For creating a custom set of Glcd images use Glcd Bitmap Editor Tool.
Note: ChipEnable(CE), FontSelect(FS) and Reverse(MD) have to be set to appropriate levels by the user outside of the T6963C_Init function. See the Library Example code at the bottom of this page.
Note: Some mikroElektronika's adapter boards have pinout different from T6369C
datasheets. Appropriate relations between these labels are given in the table below:
Adapter Board T6369C datasheet
RS
C/D
R/W
/RD
E
/WR
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
503
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
External dependencies of T6963C Graphic Lcd Library
The following variables
must be defined in all
projects using T6963C
Graphic Lcd library:
var T6963C_dataPort :
byte; sfr; external;
var T6963C_ctrlwr :
sbit; sfr; external;
var T6963C_ctrlrd :
sbit; sfr; external;
var T6963C_ctrlcd :
sbit; sfr; external;
var T6963C_ctrlrst :
sbit; sfr; external;
var
T6963C_ctrlwr_Directi
on : sbit; sfr;
external;
504
Description:
T6963C Control Port.
Write signal.
Read signal.
Command/Data signal.
Reset signal.
Direction of the Write pin.
Example :
var T6963C_dataPort :
byte at PORTD;
var T6963C_ctrlwr :
sbit at RC2_bit;
var T6963C_ctrlrd :
sbit at RC1_bit;
var T6963C_ctrlcd :
sbit at RC0_bit;
var T6963C_ctrlrst :
sbit at RC4_bit;
var
T6963C_ctrlwr_Directi
on : sbit at
TRISC2_bit;
var
T6963C_ctrlrd_Directi
Direction of the Read pin.
on : sbit; sfr;
external;
var
T6963C_ctrlcd_Directi
on : sbit at
TRISC0_bit;
var
T6963C_ctrlcd_Directi Direction of the Comon : sbit; sfr;
mand/Data pin.
external;
var
T6963C_ctrlcd_Directi
on : sbit at
TRISC0_bit;
var
T6963C_ctrlrst_Direct
Direction of the Reset pin.
ion : sbit; sfr;
external;
var
T6963C_ctrlrst_Direct
ion : sbit at
TRISC4_bit;
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Routines
- T6963C_Init
- T6963C_WriteData
- T6963C_WriteCommand
- T6963C_SetPtr
- T6963C_WaitReady
- T6963C_Fill
- T6963C_Dot
- T6963C_Write_Char
- T6963C_Write_Text
- T6963C_Line
- T6963C_Rectangle
- T6963C_Box
- T6963C_Circle
- T6963C_Image
- T6963C_Sprite
- T6963C_Set_Cursor
Note: The following low level library routines are implemented as macros. These
macros can be found in the T6963C.h header file which is located in the T6963C
example projects folders.
- T6963C_DisplayGrPanel
- T6963C_DisplayTxtPanel
- T6963C_SetGrPanel
- T6963C_SetTxtPanel
- T6963C_PanelFill
- T6963C_GrFill
- T6963C_TxtFill
- T6963C_Cursor_Height
- T6963C_Graphics
- T6963C_Text
- T6963C_Cursor
- T6963C_Cursor_Blink
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
505
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
T6963C_Init
Prototype
procedure T6963C_init(width, height, fntW : byte);
Returns
Nothing.
Initalizes the Graphic Lcd controller.
Parameters :
- width: width of the Glcd panel
- height: height of the Glcd panel
- fntW: font width
Display RAM organization:
The library cuts the RAM into panels : a complete panel is one graphics panel
followed by a text panel (see schematic below).
Description
schematic:
+---------------------+ /\
+ GRAPHICS PANEL #0
+ |
+
+ |
+
+ |
+
+ |
+---------------------+ | PANEL 0
+ TEXT PANEL #0
+ |
+
+ \/
+---------------------+ /\
+ GRAPHICS PANEL #1
+ |
+
+ |
+
+ |
+
+ |
+---------------------+ | PANEL 1
+ TEXT PANEL #1
+ |
+
+ |
+---------------------+ \/
Global variables :
Requires
-
T6963C_dataPort: Data Port
T6963C_ctrlwr: Write signal pin
T6963C_ctrlrd: Read signal pin
T6963C_ctrlcd: Command/Data signal pin
T6963C_ctrlrst: Reset signal pin
T6963C_ctrlwr_Direction: Direction of Write signal pin
T6963C_ctrlrd_Direction: Direction of Read signal pin
T6963C_ctrlcd_Direction: Direction of Command/Data signal pin
T6963C_ctrlrst_Direction: Direction of Reset signal pin
must be defined before using this function.
506
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
// T6963C module connections
var T6963C_dataPort : byte at PORTD;
Example
var T6963C_ctrlwr : sbit at RC2_bit;
var T6963C_ctrlrd : sbit at RC1_bit;
var T6963C_ctrlcd : sbit at RC0_bit;
var T6963C_ctrlrst : sbit at RC4_bit;
var T6963C_ctrlwr_Direction : sbit at TRISC2_bit;
var T6963C_ctrlrd_Direction : sbit at TRISC1_bit;
var T6963C_ctrlcd_Direction : sbit at TRISC0_bit;
var T6963C_ctrlrst_Direction : sbit at TRISC4_bit;
// End of T6963C module connections
...
// init display for 240 pixel width, 128 pixel height and 8 bits
character width
T6963C_init(240, 128, 8);
T6963C_WriteData
Prototype
procedure T6963C_WriteData(mydata : byte);
Returns
Nothing.
Writes data to T6963C controller.
Description Parameters :
- mydata: data to be written
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
T6963C_WriteData(AddrL);
T6963C_WriteCommand
Prototype
procedure T6963C_WriteCommand(mydata : byte);
Returns
Nothing.
Writes command to T6963C controller.
Description Parameters :
- mydata: command to be written
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
T6963C_WriteCommand(T6963C_CURSOR_POINTER_SET);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
507
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
T6963C_SetPtr
Prototype
procedure T6963C_SetPtr(p : word; c : byte);
Returns
Nothing.
Sets the memory pointer p for command c.
Description
Parameters :
- p: address where command should be written
- c: command to be written
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
T6963C_SetPtr(T6963C_grHomeAddr + start,
T6963C_ADDRESS_POINTER_SET);
T6963C_WaitReady
Prototype
procedure T6963C_WaitReady();
Returns
Nothing.
Description Pools the status byte, and loops until Toshiba Glcd module is ready.
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
T6963C_WaitReady();
T6963C_Fill
Prototype
procedure T6963C_Fill(v : byte; start, len : word);
Returns
Nothing.
Fills controller memory block with given byte.
Parameters :
Description
- v: byte to be written
- start: starting address of the memory block
- len: length of the memory block in bytes
508
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
T6963C_Fill(0x33,0x00FF,0x000F);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
T6963C_Dot
Prototype
procedure T6963C_Dot(x, y : integer; color : byte);
Returns
Nothing.
Draws a dot in the current graphic panel of Glcd at coordinates (x, y).
Parameters :
Description
- x: dot position on x-axis
- y: dot position on y-axis
- color: color parameter. Valid values: T6963C_BLACK and T6963C_WHITE
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
T6963C_Dot(x0, y0, pcolor);
T6963C_Write_Char
Prototype
procedure T6963C_Write_Char(c, x, y, mode : byte);
Returns
Nothing.
Writes a char in the current text panel of Glcd at coordinates (x, y).
Parameters :
-
c: char to be written
x: char position on x-axis
y: char position on y-axis
mode: mode parameter. Valid values: T6963C_ROM_MODE_OR,
T6963C_ROM_MODE_XOR, T6963C_ROM_MODE_AND and
T6963C_ROM_MODE_TEXT
Mode parameter explanation:
Description
- OR Mode: In the OR-Mode, text and graphics can be displayed and the data
is logically “OR-ed”. This is the most common way of combining text and
graphics for example labels on buttons.
- XOR-Mode: In this mode, the text and graphics data are combined via the
logical “exclusive OR”. This can be useful to display text in the negative mode,
i.e. white text on black background.
- AND-Mode: The text and graphic data shown on display are combined via the
logical “AND function”.
- TEXT-Mode: This option is only available when displaying just a text. The Text
Attribute values are stored in the graphic area of display memory.
For more details see the T6963C datasheet.
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
T6963C_Write_Char('A',22,23,AND);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
509
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
T6963C_Write_Text
Prototype
procedure T6963C_Write_Text(var str : array[10] of byte; x, y,
mode : byte);
Returns
Nothing.
Writes text in the current text panel of Glcd at coordinates (x, y).
Parameters :
-
str: text to be written
x: text position on x-axis
y: text position on y-axis
mode: mode parameter. Valid values: T6963C_ROM_MODE_OR,
T6963C_ROM_MODE_XOR, T6963C_ROM_MODE_AND and
T6963C_ROM_MODE_TEXT
Mode parameter explanation:
Description
- OR Mode: In the OR-Mode, text and graphics can be displayed and the data
is logically “OR-ed”. This is the most common way of combining text and
graphics for example labels on buttons.
- XOR-Mode: In this mode, the text and graphics data are combined via the
logical “exclusive OR”. This can be useful to display text in the negative mode,
i.e. white text on black background.
- AND-Mode: The text and graphic data shown on display are combined via the
logical “AND function”.
- TEXT-Mode: This option is only available when displaying just a text. The Text
Attribute values are stored in the graphic area of display memory.
For more details see the T6963C datasheet.
510
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
T6963C_Write_Text(" Glcd LIBRARY DEMO, WELCOME !", 0, 0,
T6963C_ROM_MODE_XOR);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
T6963C_Line
Prototype
procedure T6963C_Line(x0, y0, x1, y1 : integer; pcolor : byte);
Returns
Nothing.
Draws a line from (x0, y0) to (x1, y1).
Parameters :
Description -
x0: x coordinate of the line start
y0: y coordinate of the line end
x1: x coordinate of the line start
y1: y coordinate of the line end
pcolor: color parameter. Valid values: T6963C_BLACK and T6963C_WHITE
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
T6963C_Line(0, 0, 239, 127, T6963C_WHITE);
T6963C_Rectangle
Prototype
procedure T6963C_Rectangle(x0, y0, x1, y1 : integer; pcolor :
byte);
Returns
Nothing.
Draws a rectangle on Glcd.
Parameters :
Description -
x0: x coordinate of the upper left rectangle corner
y0: y coordinate of the upper left rectangle corner
x1: x coordinate of the lower right rectangle corner
y1: y coordinate of the lower right rectangle corner
pcolor: color parameter. Valid values: T6963C_BLACK and T6963C_WHITE
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
T6963C_Rectangle(20, 20, 219, 107, T6963C_WHITE);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
511
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
T6963C_Box
Prototype
procedure T6963C_Box(x0, y0, x1, y1 : integer; pcolor : byte);
Returns
Nothing.
Draws a box on Glcd
Parameters :
Description -
x0: x coordinate of the upper left box corner
y0: y coordinate of the upper left box corner
x1: x coordinate of the lower right box corner
y1: y coordinate of the lower right box corner
pcolor: color parameter. Valid values: T6963C_BLACK and T6963C_WHITE
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
T6963C_Box(0, 119, 239, 127, T6963C_WHITE);
T6963C_Circle
Prototype
procedure T6963C_Circle(x, y : integer; r : longint; pcolor : word);
Returns
Nothing.
Draws a circle on Glcd.
Parameters :
Description
512
-
x: x coordinate of the circle center
y: y coordinate of the circle center
r: radius size
pcolor: color parameter. Valid values: T6963C_BLACK and T6963C_WHITE
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
T6963C_Circle(120, 64, 110, T6963C_WHITE);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
T6963C_Image
Prototype
procedure T6963C_Image(const code pic : ^byte);
Returns
Nothing.
Displays bitmap on Glcd.
Parameters :
- pic: image to be displayed. Bitmap array can be located in both code and
RAM memory (due to the mikroPascal PRO for PIC pointer to const and
Description
pointer to RAM equivalency).
Use the mikroPascal’s integrated Glcd Bitmap Editor (menu option Tools › Glcd
Bitmap Editor) to convert image to a constant array suitable for displaying on
Glcd.
Note: Image dimension must match the display dimension.
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
T6963C_Image(mc);
T6963C_Sprite
Prototype
procedure T6963C_Sprite(px, py : byte; const pic : ^byte; sx, sy
: byte);
Returns
Nothing.
Fills graphic rectangle area (px, py) to (px+sx, py+sy) with custom size picture.
Parameters :
- px: x coordinate of the upper left picture corner. Valid values: multiples of the
font width
Description - py: y coordinate of the upper left picture corner
- pic: picture to be displayed
- sx: picture width. Valid values: multiples of the font width
- sy: picture height
Note: If px and sx parameters are not multiples of the font width they will be
scaled to the nearest lower number that is a multiple of the font width.
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
T6963C_Sprite(76, 4, einstein, 88, 119); // draw a sprite
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
513
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
T6963C_Set_Cursor
Prototype
procedure T6963C_Set_Cursor(x, y : byte);
Returns
Nothing.
Sets cursor to row x and column y.
Description
Parameters :
- x: cursor position row number
- y: cursor position column number
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
T6963C_Set_Cursor(cposx, cposy);
T6963C_DisplayGrPanel
Prototype
procedure T6963C_DisplayGrPanel(n : byte);
Returns
Nothing.
Display selected graphic panel.
Description Parameters :
- n: graphic panel number. Valid values: 0 and 1.
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
// display graphic panel 1
T6963C_DisplayGrPanel(1);
T6963C_DisplayTxtPanel
Prototype
procedure T6963C_DisplayTxtPanel(n : byte);
Returns
Nothing.
Display selected text panel.
Description Parameters :
- n: text panel number. Valid values: 0 and 1.
514
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
// display text panel 1
T6963C_DisplayTxtPanel(1);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
T6963C_SetGrPanel
Prototype
procedure T6963C_SetGrPanel(n : byte);
Returns
Nothing.
Compute start address for selected graphic panel and set appropriate internal pointers. All subsequent graphic operations will be preformed at this graphic panel.
Description
Parameters :
- n: graphic panel number. Valid values: 0 and 1.
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
// set graphic panel 1 as current graphic panel.
T6963C_SetGrPanel(1);
T6963C_SetTxtPanel
Prototype
procedure T6963C_SetTxtPanel(n : byte);
Returns
Nothing.
Compute start address for selected text panel and set appropriate internal pointers. All subsequent text operations will be preformed at this text panel.
Description
Parameters :
- n: text panel number. Valid values: 0 and 1.
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
// set text panel 1 as current text panel.
T6963C_SetTxtPanel(1);
T6963C_PanelFill
Prototype
procedure T6963C_PanelFill(v : byte);
Returns
Nothing.
Fill current panel in full (graphic+text) with appropriate value (0 to clear).
Description Parameters :
- v: value to fill panel with.
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
clear current panel
T6963C_PanelFill(0);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
515
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
T6963C_GrFill
Prototype
procedure T6963C_GrFill(v : byte);
Returns
Nothing.
Fill current graphic panel with appropriate value (0 to clear).
Description Parameters :
- v: value to fill graphic panel with.
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
// clear current graphic panel
T6963C_GrFill(0);
T6963C_TxtFill
Prototype
procedure T6963C_TxtFill(v : byte);
Returns
Nothing.
Fill current text panel with appropriate value (0 to clear).
Description Parameters :
- v: this value increased by 32 will be used to fill text panel.
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
// clear current text panel
T6963C_TxtFill(0);
T6963C_Cursor_Height
Prototype
procedure T6963C_Cursor_Height(n : byte);
Returns
Nothing.
Set cursor size.
Description Parameters :
- n: cursor height. Valid values: 0..7.
516
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
T6963C_Cursor_Height(7);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
T6963C_Graphics
Prototype
procedure T6963C_Graphics(n : byte);
Returns
Nothing.
Enable/disable graphic displaying.
Description
Parameters :
- n: on/off parameter. Valid values: 0 (disable graphic dispaying) and 1 (enable
graphic displaying).
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
// enable graphic displaying
T6963C_Graphics(1);
T6963C_Text
Prototype
procedure T6963C_Text(n : byte);
Returns
Nothing.
Enable/disable text displaying.
Description
Parameters :
- n: on/off parameter. Valid values: 0 (disable text dispaying) and 1 (enable text
displaying).
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
// enable text displaying
T6963C_Text(1);
T6963C_Cursor
Prototype
procedure T6963C_Cursor(n : byte);
Returns
Nothing.
Set cursor on/off.
Description Parameters :
- n: on/off parameter. Valid values: 0 (set cursor off) and 1 (set cursor on).
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
// set cursor on
T6963C_Cursor(1);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
517
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
T6963C_Cursor_Blink
Prototype
procedure T6963C_Cursor_Blink(n : byte);
Returns
Nothing.
Enable/disable cursor blinking.
Description
Parameters :
- n: on/off parameter. Valid values: 0 (disable cursor blinking) and 1 (enable
cursor blinking).
Requires
Toshiba Glcd module needs to be initialized. See the T6963C_Init routine.
Example
// enable cursor blinking
T6963C_Cursor_Blink(1);
Library Example
The following drawing demo tests advanced routines of the T6963C Glcd library. Hardware configurations in this example are made for the T6963C 240x128 display, EasyPIC5 board and 16F887.
program T6963C_240x128;
uses __Lib_T6963C_Consts, einstein_bmp, mikroe_bmp;
// T6963C module connections
var T6963C_dataPort : byte at PORTD;
var
var
var
var
var
var
var
nal
var
T6963C_ctrlwr : sbit at RC2_bit;
// WR write signal
T6963C_ctrlrd : sbit at RC1_bit;
// RD read signal
T6963C_ctrlcd : sbit at RC0_bit;
// CD command/data signal
T6963C_ctrlrst : sbit at RC4_bit;
// RST reset signal
T6963C_ctrlwr_Direction : sbit at TRISC2_bit; // WR write signal direction
T6963C_ctrlrd_Direction : sbit at TRISC1_bit; // RD read signal direction
T6963C_ctrlcd_Direction : sbit at TRISC0_bit;
// CD command/data sigdirection
T6963C_ctrlrst_Direction : sbit at TRISC4_bit; // RST reset signal direction
// Signals not used by library, they
var T6963C_ctrlce : sbit at RC3_bit;
var T6963C_ctrlfs : sbit at RC6_bit;
var T6963C_ctrlmd : sbit at RC5_bit;
var T6963C_ctrlce_Direction : sbit at
var T6963C_ctrlfs_Direction : sbit at
var T6963C_ctrlmd_Direction : sbit at
// End T6963C module connections
518
// DATA port
are set in main function
// CE signal
// FS signal
// MD signal
TRISC3_bit;
// CE signal direction
TRISC6_bit;
// FS signal direction
TRISC5_bit;
// MD signal direction
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
var
Libraries
panel : byte;
// current panel
i : word;
// general purpose register
curs : byte;
// cursor visibility
cposx,
cposy : word;
// cursor x-y position
txtcols : byte;
// number of text coloms
txt, txt1 : string[29];
begin
txt1 := ' EINSTEIN WOULD HAVE LIKED mE';
txt := ' GLCD LIBRARY DEMO, WELCOME !';
ANSEL := 0;
ANSELH := 0;
C1ON_bit := 0;
C2ON_bit := 0;
TRISB0_bit
TRISB1_bit
TRISB2_bit
TRISB3_bit
TRISB4_bit
:=
:=
:=
:=
:=
// Configure AN pins as digital I/O
// Disable comparators
1;
1;
1;
1;
1;
T6963C_ctrlce_Direction := 0;
T6963C_ctrlce := 0;
T6963C_ctrlfs_Direction := 0;
T6963C_ctrlfs := 0;
T6963C_ctrlmd_Direction := 0;
T6963C_ctrlmd := 0;
//
//
//
//
//
Set
Set
Set
Set
Set
RB0
RB1
RB2
RB3
RB4
as
as
as
as
as
input
input
input
input
input
// Enable T6963C
// Font Select 8x8
// Column number select
panel := 0;
i := 0;
curs := 0;
cposx := 0;
cposy := 0;
// Initialize T6369C
T6963C_init(240, 128, 8);
{*
* Enable both graphics and text display at the same time
*}
T6963C_graphics(1);
T6963C_text(1);
{*
* Text messages
*}
T6963C_write_text(txt, 0, 0, T6963C_ROM_MODE_XOR);
T6963C_write_text(txt1, 0, 15, T6963C_ROM_MODE_XOR);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
519
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
{*
* Cursor
*}
T6963C_cursor_height(8);
T6963C_set_cursor(0, 0);
T6963C_cursor(0);
// 8 pixel height
// Move cursor to top left
// Cursor off
{*
* Draw rectangles
*}
T6963C_rectangle(0, 0, 239, 127, T6963C_WHITE);
T6963C_rectangle(20, 20, 219, 107, T6963C_WHITE);
T6963C_rectangle(40, 40, 199, 87, T6963C_WHITE);
T6963C_rectangle(60, 60, 179, 67, T6963C_WHITE);
{*
* Draw a cross
*}
T6963C_line(0, 0, 239, 127, T6963C_WHITE);
T6963C_line(0, 127, 239, 0, T6963C_WHITE);
{*
* Draw solid boxes
*}
T6963C_box(0, 0, 239, 8, T6963C_WHITE);
T6963C_box(0, 119, 239, 127, T6963C_WHITE);
//while true do nop;
{*
* Draw circles
*}
T6963C_circle(120, 64, 10, T6963C_WHITE);
T6963C_circle(120, 64, 30, T6963C_WHITE);
T6963C_circle(120, 64, 50, T6963C_WHITE);
T6963C_circle(120, 64, 70, T6963C_WHITE);
T6963C_circle(120, 64, 90, T6963C_WHITE);
T6963C_circle(120, 64, 110, T6963C_WHITE);
T6963C_circle(120, 64, 130, T6963C_WHITE);
T6963C_sprite(76, 4, @einstein, 88, 119);
T6963C_setGrPanel(1);
graphic panel
// Draw a sprite
// Select other
T6963C_sprite(0, 0,
@mikroe_bmp, 240, 64);// 240x128 can't be
stored in most of PIC16 MCUs
T6963C_sprite(0, 64, @mikroe_bmp, 240, 64);//
it is replaced with
smaller picture 240x64
//
Smaller
picture is drawn two times
520
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
while (TRUE) do
begin
Libraries
// Endless loop
{*
* If PORTA_0 is pressed, toggle the display between graphic
panel 0 and graphic 1
*}
if( RB0_bit <> 0) then
begin
T6963C_graphics(1);
T6963C_text(0);
Delay_ms(300);
end
{*
* If PORTA_1 is pressed, display only graphic panel
*}
else
if ( RB1_bit <> 0) then
begin
Inc(panel) ;
panel := panel and 1;
T6963C_setPtr((T6963C_grMemSize + T6963C_txtMemSize) *
panel, T6963C_GRAPHIC_HOME_ADDRESS_SET) ;
Delay_ms(300) ;
end
{*
* If PORTA_2 is pressed, display only text panel
*}
else
if ( RB2_bit <> 0) then
begin
T6963C_graphics(0) ;
T6963C_text(1) ;
Delay_ms(300) ;
end
{*
* If PORTA_3 is pressed, display text and graphic panels
*}
else
if ( RB3_bit <> 0) then
begin
T6963C_graphics(1) ;
T6963C_text(1) ;
Delay_ms(300) ;
end
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
521
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
{*
* If PORTA_4 is pressed, change cursor
*}
else
if( RB4_bit <> 0) then
begin
Inc(curs);
if (curs = 3) then
curs := 0;
case curs of
0:
// no cursor
T6963C_cursor(0) ;
1: begin
// blinking cursor
T6963C_cursor(1) ;
T6963C_cursor_blink(1) ;
end;
2: begin
// non blinking cursor
T6963C_cursor(1) ;
T6963C_cursor_blink(0) ;
end;
end;
Delay_ms(300) ;
end;
{*
* Move cursor, even if not visible
*}
Inc(cposx);
if (cposx = T6963C_txtCols) then
begin
cposx := 0 ;
Inc(cposy);
if (cposy = T6963C_grHeight / T6963C_CHARACTER_HEIGHT) then
cposy := 0 ;
end;
T6963C_set_cursor(cposx, cposy) ;
Delay_ms(100) ;
end;
end.
522
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
HW Connection
T6963C Glcd HW connection
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
523
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
UART LIBRARY
UART hardware module is available with a number of PIC MCUs. mikroPascal PRO for
PIC UART Library provides comfortable work with the Asynchronous (full duplex) mode.
You can easily communicate with other devices via RS-232 protocol (for example
with PC, see the figure at the end of the topic – RS-232 HW connection). You need
a PIC MCU with hardware integrated UART, for example 16F887. Then, simply use
the functions listed below.
Note: Some PIC18 MCUs have multiple UART modules. Switching between the
UART modules in the UART library is done by the UART_Set_Active function (UART
module has to be previously initialized).
Note: In order to use the desired UART library routine, simply change the number
1 in the prototype with the appropriate module number, i.e. UART2_Init(2400);
Library Routines
-
524
UART1_Init
UART1_Data_Ready
UART1_Tx_Idle
UART1_Read
UART1_Read_Text
UART1_Write
UART1_Write_Text
UART_Set_Active
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
UART1_Init
Prototype
procedure UART1_Init(baud_rate: longint);
Returns
Nothing.
Initializes hardware UART module with the desired baud rate. Refer to the
device data sheet for baud rates allowed for specific Fosc. If you specify the
unsupported baud rate, compiler will report an error.
Description Parameters :
- baud_rate: requested baud rate
Refer to the device data sheet for baud rates allowed for specific Fosc.
You'll need PIC MCU with hardware UART.
UART1_Init needs to be called before using other functions from UART Library.
Requires
Example
Note: Calculation of the UART baud rate value is carried out by the compiler, as
it would produce a relatively large code if performed on the libary level.
Therefore, compiler needs to know the value of the parameter in the compile
time. That is why this parameter needs to be a constant, and not a variable.
This will initialize hardware UART1 module and establish the communication at
2400 bps:
UART1_Init(2400);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
525
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
UART1_Data_Ready
Prototype
function UART1_Data_Ready(): byte;
Returns
Function returns 1 if data is ready or 0 if there is no data.
Description The function tests if data in receive buffer is ready for reading.
MCU with the UART module.
Requires
Example
The UART module must be initialized before using this routine. See the
UART1_Init routine.
var receive: byte;
...
// read data if ready
if (UART1_Data_Ready() = 1) then
receive := UART1_Read();
UART1_Tx_Idle
Prototype
function UART1_Tx_Idle(): byte
Returns
- 1 if the data has been transmitted
- 0 otherwise
Description Use the function to test if the transmit shift register is empty or not.
526
Requires
UART HW module must be initialized and communication established before
using this function. See UART1_Init.
Example
// If the previous data has been shifted out, send next data:
if (UART1_Tx_Idle() <> 0)
begin
...
end;
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
UART1_Read
Prototype
function UART1_Read(): byte;
Returns
Received byte.
Description
The function receives a byte via UART. Use the UART1_Data_Ready function
to test if data is ready first.
MCU with the UART module.
Requires
Example
The UART module must be initialized before using this routine. See UART1_Init
routine.
var receive: byte;
...
// read data if ready
if (UART1_Data_Ready() = 1) then
receive := UART1_Read();
UART1_Read_Text
Prototype
procedure UART1_Read_Text(var Output, Delimiter : array[255] of
byte; Attempts : byte);
Returns
Nothing.
Reads characters received via UART until the delimiter sequence is detected.
The read sequence is stored in the parameter output; delimiter sequence is
stored in the parameter delimiter.
Description
Requires
This is a blocking call: the delimiter sequence is expected, otherwise the procedure exits( if the delimiter is not found). Parameter Attempts defines number of
received characters in which Delimiter sequence is expected. If Attempts is
set to 255, this routine will continuously try to detect the Delimiter sequence.
UART HW module must be initialized and communication established before
using this function. See UART1_Init.
Read text until the sequence “OK” is received, and send back what’s been received:
UART1_Init(4800);
Delay_ms(100);
Example
// initialize UART module
while TRUE do
begin
if (UART1_Data_Ready() = 1) then
// if data is received
begin
UART1_Read_Text(output, 'delim', 10); // reads text
until 'delim' is found
UART1_Write_Text(output);
// sends back text
end;
end;
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
527
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
UART1_Write
Prototype
procedure UART1_Write(TxData: byte);
Returns
Nothing.
The function transmits a byte via the UART module.
Description Parameters :
- TxData: data to be sent
MCU with the UART module.
Requires
Example
The UART module must be initialized before using this routine. See UART1_Init
routine.
var data_: byte;
...
data := 0x1E
UART1_Write(data_);
UART1_Write_Text
Prototype
procedure UART1_Write_Text(var uart_text : array[255]) of byte);
Returns
Nothing.
Description Sends text (parameter uart_text) via UART. Text should be zero terminated.
Requires
UART HW module must be initialized and communication established before
using this function. See UART1_Init.
Read text until the sequence “OK” is received, and send back what’s been received:
UART1_Init(4800);
Delay_ms(100);
Example
528
// initialize UART module
while TRUE do
begin
if (UART1_Data_Ready() = 1) then
// if data is received
begin
UART1_Read_Text(output, 'delim', 10); // reads text
until 'delim' is found
UART1_Write_Text(output);
// sends back text
end;
end;
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
UART_Set_Active
Prototype
procedure UART_Set_Active (read_ptr : ^Tread_ptr; write_ptr :
^Twrite_ptr; ready_ptr : ^Tready_ptr; tx_idle_ptr :
^Ttx_idle_ptr);
Returns
Nothing.
Sets active UART module which will be used by the UART library routines.
Parameters :
Description
-
read_ptr: UART1_Read handler
write_ptr: UART1_Write handler
ready_ptr: UART1_Data_Ready handler
tx_idle_ptr: UART1_Tx_Idle handler
Routine is available only for MCUs with two UART modules.
Requires
Example
Used UART module must be initialized before using this routine. See
UART1_Init routine
// Activate UART2 module
UART_Set_Active(@UART1_Read, @UART1_Write, @UART1_Data_Ready,
@UART1_Tx_Idle);
Library Example
This example demonstrates simple data exchange via UART. If MCU is connected to the PC, you
can test the example from the mikroPascal PRO for PIC USART Terminal.
program UART;
var uart_rd : byte;
begin
UART1_Init(9600);
Delay_ms(100);
while (TRUE) do
begin
if (UART1_Data_Ready() <> 0) then
begin
uart_rd := UART1_Read();
UART1_Write(uart_rd);
end;
end;
end.
// Initialize UART module at 9600 bps
// Wait for UART module to stabilize
// Endless loop
// If data is received,
//
//
read the received data,
and send data via UART
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
529
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
HW Connection
UART HW connection
530
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
USB HID LIBRARY
Universal Serial Bus (USB) provides a serial bus standard for connecting a wide variety of
devices, including computers, cell phones, game consoles, PDA’s, etc.
mikroPascal PRO for PIC includes a library for working with human interface devices via Universal Serial Bus. A human interface device or HID is a type of computer device that interacts directly with and takes input from humans, such as the keyboard, mouse, graphics tablet, and the like.
Descriptor File
Each project based on the USB HID library should include a descriptor source file which contains
vendor id and name, product id and name, report length, and other relevant information. To create a descriptor file, use the integrated USB HID terminal of mikroPascal PRO for PIC (Tools ›
USB HID Terminal). The default name for descriptor file is USBdsc.ppas, but you may rename it.
The provided code in the “Examples” folder works at 48MHz, and the flags should not be modified without consulting the appropriate datasheet first.
Library Routines
-
Hid_Enable
Hid_Read
Hid_Write
Hid_Disable
Hid_Enable
Prototype
procedure Hid_Enable(readbuff, writebuff : word);
Returns
Nothing.
Enables USB HID communication. Parameters readbuff and writebuff are
the addresses of Read Buffer and the Write Buffer, respectively, which are used
Description for HID communication. You can pass buffer names with the @ operator.
This function needs to be called before using other routines of USB HID Library.
Requires
Nothing.
Example
Hid_Enable(@rd, @wr);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
531
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Hid_Read
Prototype
function Hid_Read() : byte;
Returns
Number of characters in the Read Buffer received from the host.
Description
Receives message from host and stores it in the Read Buffer. Function returns
the number of characters received in the Read Buffer.
Requires
USB HID needs to be enabled before using this function. See Hid_Enable.
Example
length := Hid_Read();
Hid_Write
Prototype
procedure Hid_Write(writebuff : word, len : byte);
Returns
Nothing.
Function sends data from Write Buffer writebuff to host. Write Buffer is the
address of the parameter used in initialization; see Hid_Enable. You can pass a
Description
buffer name with the @ operator. Parameter len should specify a length of the
data to be transmitted.
Requires
USB HID needs to be enabled before using this function. See Hid_Enable.
Example
Hid_Write(@wr, len);
Hid_Disable
Prototype
procedure Hid_Disable();
Returns
Nothing.
Description Disables USB HID communication.
Requires
USB HID needs to be enabled before using this function. See Hid_Enable.
Example
Hid_Disable();
Library Example
This example establishes connection with the HID terminal that is active on the PC. Upon connection establishment, the HID Device Name will appear in the respective window. After that software will wait for data and it will return received data back. Examples uses USBdsc descriptor file,
which is in the same folder, and can be created by the HID Terminal.
532
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
program USB_HID_test;
uses USBdsc;
var
k, i, ch
: byte;
userWR_buffer : array[64] of byte;
userRD_buffer : array[64] of byte;
// Main Interrupt Routine
procedure interrupt;
begin
HID_InterruptProc;
end;
// Initialization Routine
procedure Init_Main;
begin
// Disable interrupts
INTCON := 0;
// Disable GIE, PEIE,
TMR0IE,INT0IE,RBIE
INTCON2 := 0xF5;
INTCON3 := 0xC0;
RCON.IPEN := 0;
// Disable Priority Levels on interrupts
PIE1 := 0;
PIE2 := 0;
PIR1 := 0;
PIR2 := 0;
ADCON1 := ADCON1 or 0x0F;
log function as digital
// Ports Configuration
TRISA := 0xFF;
TRISB := 0xFF;
TRISC := 0xFF;
TRISD := 0;
TRISE := 0x07;
LATA
LATB
LATC
LATD
LATE
end;
:=
:=
:=
:=
:=
// Configure all ports with ana-
0;
0;
0;
0;
0;
// Main Program Routine
begin
Init_Main();
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
533
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
HID_Enable(@userRD_buffer, @userWR_buffer);
Delay_mS(1000);
Delay_mS(1000);
while true do
begin
k := HID_Read();
i := 0;
while i < k do
begin
ch := userRD_buffer[0];
userWR_buffer[0] := ch;
HID_Write(@userWR_buffer, 1);
inc(i);
end;
end;
HID_Disable();
end.
HW Connection
USB connection scheme
534
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
MISCELLANEOUS LIBRARIES
- Button Library
- Conversions Library
- Math Library
- String Library
- Time Library
- Trigonometry Library
BUTTON LIBRARY
Button library contains miscellaneous routines useful for project development.
- Button
Button
Prototype
function Button(var port : byte; pin, time, active_state : byte)
: byte;
Returns
Returns 0 or 255.
Function eliminates the influence of contact flickering upon pressing a button
(debouncing).
Description Parameter port specifies the location of the button; parameter pin is the pin
number on designated port and goes from 0..7; parameter time is a debounce
period in milliseconds; parameter active_state can be either 0 or 1, and it
determines if the button is active upon logical zero or logical one.
Requires
Button pin must be configured as input.
Example reads RB0, to which the button is connected; on transition from 1 to 0
(release of button), PORTD is inverted:
Example
while true do
begin
if Button(PORTB, 0, 1, 1) then oldstate := 255;
if oldstate and Button(PORTB, 0, 1, 0) then
begin
PORTD := not(PORTD);
oldstate := 0;
end;
end;
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
535
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
CONVERSIONS LIBRARY
mikroPascal PRO for PIC Conversions Library provides routines for numerals to strings and
BCD/decimal conversions.
Library Routines
You can get text representation of numerical value by passing it to one of the following routines:
-
ByteToStr
ShortToStr
WordToStr
IntToStr
LongintToStr
LongWordToStr
FloatToStr
StrToInt
StrToWord
The following functions convert decimal values to BCD and vice versa:
- Dec2Bcd
- Bcd2Dec16
- Dec2Bcd16
ByteToStr
Prototype
procedure ByteToStr(input : word; var output : array[3] of char);
Returns
Nothing.
Converts input byte to a string. The output string is right justified and remaining
positions on the left (if any) are filled with blanks.
Description Parameters :
- input: byte to be converted
- output: destination string
536
Requires
Nothing.
Example
var t : word;
txt : array[3] of char;
...
t := 24;
ByteToStr(t, txt); // txt is " 24" (one blank here)
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
ShortToStr
Prototype
procedure ShortToStr(input : short; var output : array[4] of char);
Returns
Nothing.
Converts input short (signed byte) number to a string. The output string is right
justified and remaining positions on the left (if any) are filled with blanks.
Description Parameters :
- input: short number to be converted
- output: destination string
Requires
Nothing.
Example
var t : short;
txt : array[4] of char;
...
t := -24;
ByteToStr(t, txt); // txt is " -24" (one blank here)
WordToStr
Prototype
procedure WordToStr(input : word; var output : array[5] of char);
Returns
Nothing.
Converts input word to a string. The output string is right justified and the
remaining positions on the left (if any) are filled with blanks.
Description Parameters :
- input: word to be converted
- output: destination string
Requires
Nothing.
Example
var t : word;
array[5] of char;
...
t := 437;
WordToStr(t, txt); // txt is "
437" (two blanks here)
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
537
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
IntToStr
Prototype
procedure IntToStr(input : integer; var output : array[6] of char);
Returns
Nothing.
Converts input integer number to a string. The output string is right justified and
the remaining positions on the left (if any) are filled with blanks.
Description Parameters :
- input: integer number to be converted
- output: destination string
Requires
Nothing.
Example
var input : integer;
txt : string[5];
//...
begin
input := -4220;
IntToStr(input, txt);
// txt is ' -4220'
LongintToStr
Prototype
procedure LongintToStr(input : longint; var output : array[11] of
char);
Returns
Nothing.
Converts input longint number to a string. The output string is right justified and
the remaining positions on the left (if any) are filled with blanks.
Description Parameters :
- input: longint number to be converted
- output: destination string
538
Requires
Nothing.
Example
var input : longint;
txt : array[11] of char;
//...
begin
input := -12345678;
IntToStr(input, txt);
// txt is '
-12345678'
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
LongWordToStr
Prototype
procedure LongWordToStr(input : dword; var output : array[10] of
char);
Returns
Nothing.
Converts input double word number to a string. The output string is right justified and the remaining positions on the left (if any) are filled with blanks.
Description Parameters :
- input: double word number to be converted
- output: destination string
Requires
Nothing.
Example
var input : longint;
txt : array[10] of char;
//...
begin
input := 12345678;
IntToStr(input, txt);
// txt is '
12345678'
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
539
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
FloatToStr
Prototype
procedure FloatToStr(input : real; var output : array[23] of char);
Returns
-
3
2
1
0
if
if
if
if
input number is NaN
input number is -INF
input number is +INF
conversion was successful
Converts a floating point number to a string.
Parameters :
- input: floating point number to be converted
Description - output: destination string
The output string is left justified and null terminated after the last digit.
Note: Given floating point number will be truncated to 7 most significant digits
before conversion.
Requires
Nothing.
Example
var ff1, ff2, ff3 : real;
txt : array[23] of char;
...
ff1 := -374.2;
ff2 := 123.456789;
ff3 := 0.000001234;
FloatToStr(ff1, txt);
FloatToStr(ff2, txt);
FloatToStr(ff3, txt);
540
// txt is "-374.2"
// txt is "123.4567"
// txt is "1.234e-6"
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
StrToInt
Prototype
function StrToInt(var input:string[6]):integer;
Returns
Integer variable.
Description Converts a string to integer.
Requires
The string is assumed to be a correct representation of a number.
var ii:integer
Example
begin
ii := StrToInt('-1234');
StrToWord
Prototype
function StrToWord(var input:string[5]):word;
Returns
Word variable.
Description Converts a string to word.
Requires
input string with length of max 5 chars.
The string is assumed to be a correct representation of a number.
var ww:word;
Example
begin
ww := StrToword('65432');
Dec2Bcd
Prototype
function Dec2Bcd(decnum : byte) : byte;
Returns
Converted BCD value.
Converts input number to its appropriate BCD representation.
Description Parameters :
- decnum: number to be converted
Requires
Nothing.
Example
var a, b : byte;
...
a := 22;
b := Dec2Bcd(a); // b equals 34
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
541
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Bcd2Dec16
Prototype
function Bcd2Dec16(bcdnum : word) : word;
Returns
Converted decimal value.
Converts 16-bit BCD numeral to its decimal equivalent.
Description Parameters :
- bcdnum: 16-bit BCD numeral to be converted
Requires
Nothing.
Example
var a, b : word;
...
a := 0x1234;
b := Bcd2Dec16(a);
// a equals 4660
// b equals 1234
Dec2Bcd16
Prototype
function Dec2Bcd16(decnum : word) : word;
Returns
Converted BCD value.
Converts decimal value to its BCD equivalent.
Description Parameters :
- decnum decimal number to be converted
542
Requires
Nothing.
Example
var a, b : word;
...
a := 2345;
b := Dec2Bcd16(a);
// b equals 9029
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
MATH LIBRARY
The mikroPascal PRO for PIC provides a set of library functions for floating point math handling.
See also Predefined Globals and Constants for the list of predefined math constants.
Library Functions
-
acos
asin
atan
atan2
ceil
cos
cosh
eval_poly
exp
fabs
floor
frexp
ldexp
log
log10
modf
pow
sin
sinh
sqrt
tan
tanh
acos
Prototype
function acos(x : real) : real;
The function returns the arc cosine of parameter x; that is, the value whose
Description cosine is x. The input parameter x must be between -1 and 1 (inclusive). The
return value is in radians, between 0 and Π (inclusive).
asin
Prototype
function asin(x : real) : real;
The function returns the arc sine of parameter x; that is, the value whose sine is
Description x. The input parameter x must be between -1 and 1 (inclusive). The return value
is in radians, between -Π/2 and Π/2 (inclusive).
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
543
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
atan
Prototype
function atan(arg : real) : real;
Description
The function computes the arc tangent of parameter arg; that is, the value whose
tangent is arg. The return value is in radians, between -Π/2 and Π/2 (inclusive).
atan2
Prototype
function atan2(y : real; x : real) : real;
This is the two-argument arc tangent function. It is similar to computing the arc
tangent of y/x, except that the signs of both arguments are used to determine
Description
the quadrant of the result and x is permitted to be zero. The return value is in
radians, between -Π and Π (inclusive).
ceil
Prototype
function ceil(x : real) : real;
Description The function returns value of parameter x rounded up to the next whole number.
cos
Prototype
function cos(arg : real) : real;
Description The function returns the cosine of arg in radians. The return value is from -1 to 1.
cosh
Prototype
function cosh(x : real) : real;
Description
The function returns the hyperbolic cosine of x, defined mathematically as
(ex+e-x)/2. If the value of x is too large (if overflow occurs), the function fails.
eval_poly
Prototype
function eval_poly(x : real; var d : array[10] of real; n : integer) : real;
Description
Function Calculates polynom for number x, with coefficients stored in d[], for
degree n.
exp
544
Prototype
function exp(x : real) : real;
Description
The function returns the value of e — the base of natural logarithms — raised to
the power x (i.e. ex).
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
fabs
Prototype
function fabs(d : real) : real;
Description The function returns the absolute (i.e. positive) value of d.
floor
Prototype
function floor(x : real) : real;
Description The function returns the value of parameter x rounded down to the nearest integer.
frexp
Prototype
function frexp(value : real; var eptr : integer) : real;
The function splits a floating-point value value into a normalized fraction and an
Description integral power of 2. The return value is a normalized fraction and the integer
exponent is stored in the object pointed to by eptr.
ldexp
Prototype
function ldexp(value : real; newexp : integer) : real;
Description
The function returns the result of multiplying the floating-point number value by
2 raised to the power newexp (i.e. returns value * 2newexp).
log
Prototype
function log(x : real) : real;
Description The function returns the natural logarithm of x (i.e. loge(x)).
log10
Prototype
function log10(x : real) : real;
Description The function returns the base-10 logarithm of x (i.e. log10(x)).
modf
Prototype
function modf(val : real; var iptr : real) : real;
Description
The function returns the signed fractional component of val, placing its whole
number component into the variable pointed to by iptr.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
545
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
pow
Prototype
function pow(x : real; y : real) : real;
Description
The function returns the value of x raised to the power y (i.e. xy). If x is negative, the function will automatically cast y into longint.
sin
Prototype
function sin(arg : real) : real;
Description The function returns the sine of arg in radians. The return value is from -1 to 1.
sinh
Prototype
function sinh(x : real) : real;
Description
The function returns the hyperbolic sine of x, defined mathematically as (exe-x)/2. If the value of x is too large (if overflow occurs), the function fails.
sqrt
Prototype
function sqrt(x : real) : real;
Description The function returns the non negative square root of x.
tan
Prototype
function tan(x : real) : real;
Description
The function returns the tangent of x in radians. The return value spans the
allowed range of floating point in mikroPascal PRO for PIC.
tanh
Prototype
function tanh(x : real) : real;
Description The function returns the hyperbolic tangent of x, defined mathematically as
sinh(x)/cosh(x).
546
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
STRING LIBRARY
The mikroPascal PRO for PIC includes a library which automatizes string related tasks.
Library Functions
-
memchr
memcmp
memcpy
memmove
memset
strcat
strchr
strcmp
strcpy
strlen
strncat
strncpy
strspn
strcspn
strncmp
strpbrk
strrchr
strstr
memchr
Prototype
function memchr(p : ^byte; ch : byte; n : word) : word;
The function locates the first occurrence of the word ch in the initial n words of
memory area starting at the address p. The function returns the offset of this
occurrence from the memory address p or 0xFFFF if ch was not found.
Description
For the parameter p you can use either a numerical value (literal/variable/constant) indicating memory address or a dereferenced value of an object, for
example @mystring or @PORTB.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
547
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
memcmp
Prototype
function memcmp(p1, p2 : ^byte; n : word) : short;
The function returns a positive, negative, or zero value indicating the relationship of first n words of memory areas starting at addresses p1 and p2.
This function compares two memory areas starting at addresses p1 and p2 for n
words and returns a value indicating their relationship as follows:
Value
< 0
Description = 0
> 0
Meaning
p1 "less than" p2
p1 "equal to" p2
p1 "greater than" p2
The value returned by the function is determined by the difference between the
values of the first pair of words that differ in the strings being compared.
For parameters p1 and p2 you can use either a numerical value (literal/variable/constant) indicating memory address or a dereferenced value of an object,
for example @mystring or @PORTB.
memcpy
Prototype
Description
procedure memcpy(p1, p2 : ^byte; nn : word);
The function copies nn words from the memory area starting at the address p2
to the memory area starting at p1. If these memory buffers overlap, the memcpy
function cannot guarantee that words are copied before being overwritten. If
these buffers do overlap, use the memmove function.
For parameters p1 and p2 you can use either a numerical value (literal/variable/constant) indicating memory address or a dereferenced value of an object,
for example @mystring or @PORTB.
memmove
Prototype
procedure memmove(p1, p2 : ^byte; nn : word);
The function copies nn words from the memory area starting at the address p2
to the memory area starting at p1. If these memory buffers overlap, the Memmove
function ensures that the words in p2 are copied to p1 before being overwritten.
Description
For parameters p1 and p2 you can use either a numerical value (literal/variable/constant) indicating memory address or a dereferenced value of an object,
for example @mystring or @PORTB.
548
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
memset
Prototype
procedure memset(p : ^byte; character : byte; n : word);
The function fills the first n words in the memory area starting at the address p
with the value of word character.
Description
For parameter p you can use either a numerical value (literal/variable/constant)
indicating memory address or a dereferenced value of an object, for example
@mystring or @PORTB.
strcat
Prototype
procedure strcat(var s1, s2 : string[100]);
Description
The function appends the value of string s2 to string s1 and terminates s1 with
a null character.
strchr
Prototype
function strchr(var s : string[100]; ch : byte) : word;
The function searches the string s for the first occurrence of the character ch.
The null character terminating s is not included in the search.
Description
The function returns the position (index) of the first character ch found in s; if no
matching character was found, the function returns 0xFFFF.
strcmp
Prototype
function strcmp(var s1, s2 : string[100]) : short;
The function lexicographically compares the contents of the strings s1 and s2
and returns a value indicating their relationship:
Value
< 0
Description = 0
> 0
Meaning
s1 "less than" s2
s1 "equal to" s2
s1 "greater than" s2
The value returned by the function is determined by the difference between the
values of the first pair of words that differ in the strings being compared.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
549
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
strcpy
Prototype
procedure strcpy(var s1, s2 : string[100]);
Description
The function copies the value of the string s2 to the string s1 and appends a
null character to the end of s1.
strcspn
Prototype
function strcspn(var s1, s2 : string[100]) : word;
The function searches the string s1 for any of the characters in the string s2.
Description
The function returns the index of the first character located in s1 that matches
any character in s2. If the first character in s1 matches a character in s2, a
value of 0 is returned. If there are no matching characters in s1, the length of
the string is returned (not including the terminating null character).
strlen
Prototype
function strlen(var s : string[100]) : word;
Description
The function returns the length, in words, of the string s. The length does not
include the null terminating character.
strncat
Prototype
procedure strncat(var s1, s2 : string[100]; size : byte);
The function appends at most size characters from the string s2 to the string s1
Description and terminates s1 with a null character. If s2 is shorter than the size characters, s2 is copied up to and including the null terminating character.
strncmp
Prototype
function strncmp(var s1, s2 : string[100]; len : byte) : short;
The function lexicographically compares the first len words of the strings s1 and
s2 and returns a value indicating their relationship:
Value
< 0
Description = 0
> 0
Meaning
s1 "less than" s2
s1 "equal to" s2
s1 "greater than" s2
The value returned by the function is determined by the difference between the
values of the first pair of words that differ in the strings being compared (within
first len words).
550
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
strncpy
Prototype
procedure strncpy(var s1, s2 : string[100]; size : word);
The function copies at most size characters from the string s2 to the string s1.
Description If s2 contains fewer characters than size, s1 is padded out with null characters
up to the total length of the size characters.
strpbrk
Prototype
function strpbrk(var s1, s2 : string[100]) : word;
The function searches s1 for the first occurrence of any character from the
string s2. The null terminator is not included in the search. The function returns
Description
an index of the matching character in s1. If s1 contains no characters from s2,
the function returns 0xFFFF.
strrchr
Prototype
function strrchr(var s : string[100]; ch : byte) : word;
The function searches the string s for the last occurrence of the character ch.
The null character terminating s is not included in the search. The function
Description
returns an index of the last ch found in s; if no matching character was found,
the function returns 0xFFFF.
strspn
Prototype
function strspn(var s1, s2 : string[100]) : byte;
The function searches the string s1 for characters not found in the s2 string.
Description
The function returns the index of first character located in s1 that does not
match a character in s2. If the first character in s1 does not match a character in
s2, a value of 0 is returned. If all characters in s1 are found in s2, the length of
s1 is returned (not including the terminating null character).
strstr
Prototype
function strstr(var s1, s2 : string[100]) : word;
The function locates the first occurrence of the string s2 in the string s1 (excluding the terminating null character).
Description
The function returns a number indicating the position of the first occurrence of
s2 in s1; if no string was found, the function returns 0xFFFF. If s2 is a null string,
the function returns 0.
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
551
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
TIME LIBRARY
The Time Library contains functions and type definitions for time calculations in the UNIX time format which counts the number of seconds since the "epoch". This is very convenient for programs
that work with time intervals: the difference between two UNIX time values is a real-time difference measured in seconds.
What is the epoch?
Originally it was defined as the beginning of 1970 GMT. ( January 1, 1970 Julian day ) GMT,
Greenwich Mean Time, is a traditional term for the time zone in England.
The TimeStruct type is a structure type suitable for time and date storage.
Library Routines
- Time_dateToEpoch
- Time_epochToDate
- Time_datediff
Time_dateToEpoch
Prototype
function Time_dateToEpoch(var ts : TimeStruct) : longint;
Returns
Number of seconds since January 1, 1970 0h00mn00s.
This function returns the UNIX time : number of seconds since January 1, 1970
0h00mn00s.
Description
Parameters :
- ts: time and date value for calculating UNIX time.
552
Requires
Nothing.
Example
var ts1 : TimeStruct;
Epoch : longint;
...
// what is the epoch of the date in ts ?
epoch := Time_dateToEpoch(ts1);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Time_epochToDate
Prototype
procedure Time_epochToDate(e: longint; var ts : TimeStruct);
Returns
Nothing.
Converts the UNIX time to time and date.
Description
Parameters :
- e: UNIX time (seconds since UNIX epoch)
- ts: time and date structure for storing conversion output
Requires
Nothing.
Example
var ts2 : TimeStruct;
epoch : longint;
...
//what date is epoch 1234567890 ?
epoch := 1234567890;
Time_epochToDate(epoch,ts2);
Time_dateDiff
Prototype
function Time_dateDiff(t1 : ^TimeStruct; t2 : ^TimeStruct) :
longint;
Returns
Time difference in seconds as a signed long.
This function compares two dates and returns time difference in seconds as a
signed long. The result is positive if t1 is before t2, null if t1 is the same as t2
and negative if t1 is after t2.
Description
Parameters :
- t1: time and date structure (the first comparison parameter)
- t2: time and date structure (the second comparison parameter)
Requires
Nothing.
Example
var ts1, ts2 : TimeStruct;
diff : longint;
...
//how many seconds between these two dates contained in ts1 and
ts2 buffers?
diff := Time_dateDiff(ts1, ts2);
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
553
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
Library Example
Demonstration of Time library routines usage for time calculations in UNIX time format.
program Time_Demo;
program Time_Demo;
var epoch, diff : longint;
ts1, ts2 : TimeStruct;
begin
ts1.ss
ts1.mn
ts1.hh
ts1.md
ts1.mo
ts1.yy
:=
:=
:=
:=
:=
:=
0;
7;
17;
23;
5;
2006;
{*
* What is the epoch of the date in ts ?
*}
epoch := Time_dateToEpoch(ts1);
{*
* What date is epoch 1234567890 ?
*}
epoch := 1234567890;
Time_epochToDate(epoch, ts2);
{*
* How much seconds between this two dates ?
*}
diff := Time_dateDiff(ts1, ts2);
end.
TimeStruct type definition
type TimeStruct = record
ss : byte;
// seconds
mn : byte;
// minutes
hh : byte;
// hours
md : byte;
// day in month, from 1 to 31
wd : byte; // day in week, monday=0, tuesday=1, .... sunday=6
mo : byte;
// month number, from 1 to 12 (and not from
0 to 11 as with unix C time !)
yy : word;
// year Y2K compliant, from 1892 to 2038
end;
554
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
TRIGONOMETRY LIBRARY
The mikroPascal PRO for PIC implements fundamental trigonometry functions. These functions
are implemented as look-up tables. Trigonometry functions are implemented in integer format in
order to save memory.
Library Routines
- sinE3
- cosE3
sinE3
Prototype
function sinE3(angle_deg : word): integer;
Returns
The function returns the sine of input parameter.
The function calculates sine multiplied by 1000 and rounded to the nearest integer:
result := round(sin(angle_deg)*1000)
Description Parameters:
- angle_deg: input angle in degrees
Note: Return value range: -1000..1000.
Requires
Nothing.
Example
var res : integer;
...
res := sinE3(45); // result is 707
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
555
CHAPTER 7
mikroPASCAL PRO for PIC
Libraries
cosE3
Prototype
function cosE3(angle_deg : word): integer;
Returns
The function returns the cosine of input parameter.
The function calculates cosine multiplied by 1000 and rounded to the nearest
integer:
result := round(cos(angle_deg)*1000)
Description
Parameters:
- angle_deg: input angle in degrees
Note: Return value range: -1000..1000.
556
Requires
Nothing.
Example
var res: integer;
...
res := cosE3(196);
// result is -193
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
CHAPTER 7
mikroPascal PRO for PIC
Libraries
MIKROELEKTRONIKA - SOFTWARE AND HARDWARE SOLUTIONS FOR EMBEDDED WORLD
557
">