USER MANUAL

www.prolight.co.uk

Xterior 24 Quad

Order code: LEDJ157

Xterior 36 Tri

Order code: LEDJ158

Xterior 60 CW/WW

Order code: LEDJ159

USER MANUAL

Xterior Series Safety

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOUR INITIAL START-UP!

CAUTION!

INPUT VOLTAGE OF 110~240V

SAFETY INSTRUCTIONS

Every person involved with the installation, operation & maintenance of this equipment should:

-

-

Be competent

Follow the instructions of this manual

CAUTION! TAKE CARE USING THIS EQUIPMENT!

HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!

Before your initial start-up, please make sure that there is no damage caused during transportation. Should there be any, consult your dealer and do not use the equipment.

To maintain the equipment in good working condition and to ensure safe operation, it is necessary for the user to follow the safety instructions and warning notes written in this manual.

Please note that damages caused by user modifications to this equipment are not subject to warranty.

1.

Xterior Series Safety

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorised modification to the equipment.

• Never let the power-cable come into contact with other cables. Handle the power-cable

and all mains voltage connections with particular caution!

• Never remove warning or informative labels from the equipment.

• Do not open the equipment and do not modify the equipment.

• Do not connect this equipment to a dimmer-pack.

• Do not switch the equipment on and off in short intervals, as this will reduce the

system’s life.

• Do not expose to flammable sources or gases.

• Always disconnect the power from the mains when equipment is not in use or before

cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the

power-cable.

• Make sure that the available voltage is between 220v/240v.

• Make sure that the power-cable is never crimped or damaged. Check the equipment and

the power-cable periodically.

• If the equipment is dropped or damaged, disconnect the mains power supply immediately.

Have a qualified engineer inspect the equipment before operating again.

• If your product fails to function correctly, discontinue use immediately. Pack the unit

securely (preferably in the original packing material), and return it to your Prolight dealer

for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be carried out by a qualified

technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.

• WARRANTY; One year from date of purchase.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual, the product may suffer damage and the warranty becomes void.

Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks, lamp failure etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and property.

2.

Xterior Series Introduction

Introduction

Xterior 24 Quad

Xterior 36 Tri

• 24 x 8W quad-colour LEDs

• Beam angle: 25 degrees

• 400Hz refresh rate

• 0-100% dimming and variable strobe

• DMX channels: 4/6 or 7 selectable

• Static colour, colour fade, colour change,

master/slave and DMX modes

• Optional I.R remote (LEDJ90C)

• 4 push button menu with LCD diaplay

• IP rated power in/out sockets

• IP rated 3-pin DMX in/out sockets

• Power consumption: 204W

• Power supply: 100-240V~50/60Hz

• IP rating: IP-65

• Dimensions: 320 x 140 x 325mm

• Weight: 8.4Kgs

• 36 x 3W tri-colour LEDs




• DMX channels: 3/5 or 6 selectable

• Static colour, colour fade, colour change,


• Optional I.R remote (LEDJ90B)








• Weight: 8.5Kgs

Xterior 60 CW/WW

• 60 x 3W LEDs (CW: 36, WW: 24)




• DMX channels: 2 or 5 selectable

• Static colour, dimming,


• Optional I.R remote (LEDJ90D)








• Weight: 8.2Kgs

Overview

Identification:

1, Tightening Knobs

2, Bracket

3, Power in

4, DMX in

5, DMX out

6, Power out

7, Mode button

8, Enter button

9, Up button

10, Down button

11, LCD display

XTERIOR 24 QUAD

www.prolight.co.uk

POWER IN DMX IN DMX OUT POWER OUT

Setup

Operating Instructions

The Xterior Series are DMX-512 controllable units made up of high efficiency LEDs and will operate in stand alone, master/slave or DMX control modes.

NOTE: Each unit has a password and locks after being unused for several minutes, to unlock the unit again press the buttons in the following order, “UP”, “DOWN”, “UP”, “DOWN” followed by

“ENTER”.

3.

XTERIOR 36 TRI



XTERIOR 60 CW/WW



Xterior Series Operation Modes

Xterior 24 Quad Operation modes

Built-in programmes:

To activate the units built-in programmes, press the “MODE” button to show “01.STATIC” on the

LCD screen. Press the “ENTER” button to choose between the 5 built-in programmes by using the

“UP” and “DOWN” buttons. Now press the “ENTER” button to select the desired speed and adjust by using the “UP” and “DOWN” buttons. Press the “ENTER” button once more to select the desired flash value and adjust by using the “UP” and “DOWN” buttons.

Speed values: 00 - 99 (00 = slow, 99 = fast)

Flash values: 00 - 99 (00 = slow, 99 = fast)

Programme 1 - Static colour

In this mode you can set the Xterior 24 Quad to any colour and any brightness.

When you are in the “01.STATIC” mode, press the “enter” button to change the brightness of each individual colour.

The “R” represents Red, “G” = Green, “B” = Blue, “W” = White and “F” = strobe.

The two digits after it are the brightness 00 to 99 or in “CF” they are the strobe speed.

Example: If you set R, G, B and W all to zero, the 24 Quad will have no LEDs showing (blackout).

If you set R to 99 and G, B and W to zero the 24 Quad will be 100% Red.

Programme 2 - 15 colour change

In this mode the Xterior 24 Quad will run through its 15 preset colours.


In this mode the Xterior 24 Quad will run through its 4 colours.

Programme 4 - colour fade

In this mode the Xterior 24 Quad will fade through its 15 preset colours.

DMX mode:

To activate the unit in DMX mode, press the “MODE” button to show “DMX MODE” on the LCD screen. Press the “ENTER” button and select the desired DMX address setting by using the “UP” and

“DOWN” buttons. Then to select one of the 3 DMX modes 4, 6 or 7 channel, press the “ENTER” button again to choose the desired DMX mode by using the “UP” and

“DOWN” buttons.

For the 4, 6 or 7 channel DMX address information please see page 5

NOTE: Once the desired settings have been selected in each of the above modes,

ALWAYS

confirm the settings by pressing the “ENTER” button.

Slave mode:

To activate the unit in slave mode, first you must link multiple units together and press the

“MODE” button to show “SLAVE MODE” on the LCD screen. Now on the master unit press the

“MODE” button to select the desired mode and the slave units will now run in sequence with the master unit.

4.

Xterior Series DMX Programme Charts

Xterior 24 Quad DMX Charts

4 channel mode DMX chart



5.


Xterior 24 I.R. Remote functions

I.R Remote (purchased separately: LEDJ90C)

Functions:

The “BLACKOUT” button is used to set the LEDs into the power on or off modes.

The “S PR” button is used to run the built-in programmes. To go though the built-in programmes, press the

“+” and “-” buttons.

The “FL” button is used to set the LEDs to flash on and off, to change the flash frequency use the “+” and

“-” buttons.

The “SP” button is used to set the run speed, this button is available only in the colour change or colour fade modes. To change the speed use the “+” and “-” buttons.

The “D” button is used to set the LEDs into DMX mode. (See DMX value table)

The “SA” button is used to set the LEDs into sound activated mode.

The “SL” button is used to set the LEDs into slave mode.

The “S”, “0”, “1”, “2”, “3”, “4”, “5”, “6”, “7”, “8” and “9” buttons are used to set the DMX address for the LED’s.

The “R”, “G”, “B” and “A/W” buttons are used to set the brightness for the Red, Green, Blue and Amber/

White LEDs, to change the brightness use the “+” and “-” buttons.

DMX Address Examples:

To set the DMX address “245”;

1) Press the “S” button, so the red LEDs come on, this means you can now start to set

the DMX address.

2) Press the

digit

“2” button, so the green LEDs come on, this means the first digit “2”

(the hundreds place) setting is successful.

3) Now Press the “4” button, and the blue LEDs will come on, this now means that the second

“4” (tens place) setting is successful.

4) Now Press the “5” button, and all of the R, G, B, A/W LEDs will come on, this means

that the final digit “5” (units place) setting is successful and the full DMX address setting

has been changed

5) Now press the “DMX MODE” button to save the new address into memory.


1) Press the “S” button, so the red LEDs come on, this means you can now start to set

the DMX address.

2) Press the “0” button, so the green LEDs come on, this means the first digit “0”


3) Now Press the “0” button, and the blue LEDs will come on, this now means that the second

digit “0” (tens place) setting is successful.

4) Now Press the “2” button, and all of the R, G, B, A/W LEDs will come on, this means


has been changed.


Important notes:

• Set the DMX address on each fixture before plugging into the DMX controller.

• The I.R Remote is not usable when the fixture(s) are being controlled by a DMX controller.

• The maximum transmitter distance is 10M. Please make sure that you have the

I.R remote aimed directly at each fixture to be programmed,

• If you do not press the “DMX MODE” button after you have changed the DMX address,

when you power down the fixture it will lose the address you have set.

6.


Xterior 36 Tri Operation modes

Built-in programmes:

To activate the units built-in programmes, press the “MODE” button to show “01.STATIC” on the

LCD screen. Press the “ENTER” button to choose between the 5 built-in programmes by using the

“UP” and “DOWN” buttons. Now press the “ENTER” button to select the desired speed and adjust by using the “UP” and “DOWN” buttons. Press the “ENTER” button once more to select the desired flash value and adjust by using the “UP” and “DOWN” buttons.

Speed values: 00 - 99 (00 = slow, 99 = fast)

Flash values: 00 - 99 (00 = slow, 99 = fast)

Programme 1 - Static colour

In this mode you can set the Xterior 36 Tri to any colour and any brightness.

When you are in the “01.STATIC” mode, press the “enter” button to change the brightness of each individual colour.

The “R” represents Red, “G” = Green, “B” = Blue and “F” = strobe.

The two digits after it are the brightness 00 to 99 or in “CF” they are the strobe speed.

Example: If you set R, G, and B all to zero, the 36 Tri will have no LEDs showing (blackout).

If you set R to 99 and G, and B to zero the 36 Tri will be 100% Red.


In this mode the Xterior 36 Tri will run through its 7 preset colours.


In this mode the Xterior 36 Tri will run through its 3 colours.

Programme 4 - colour fade

In this mode the Xterior 36 Tri will fade through its 7 preset colours.

DMX mode:


“DOWN” buttons. Then to select one of the 3 DMX modes 3/5 or 6 channel, press the “ENTER” button again to choose the desired DMX mode by using the “UP” and


For the 3/5 or 6 channel DMX address information please see page 5


ALWAYS


Slave mode:




7.


Xterior 36 Tri DMX Charts


Channel

1

2

3


Value

0-255

0-255

0-255

Channel

1

2

3

4

5

Value

0-255

0-255

0-255

0-255

0

1-5

6-10

11-255

Function

Red 0-100%

Green 0-100%

Blue 0-100%

Function

Red

Green

Blue

Master dimmer 0-100%

On

Off

On

Strobe (slow to fast)


Channel

1

2

3

4

5

6

Value

0-255

0-255

0-255

0-255

0-255

0-4

5-125

126-255

Function

Master dimmer 0-100%


Red

Green

Blue

On

Colour change (slow to fast)

Colour fade (slow to fast)

8.


Xterior 36 Tri I.R. Remote functions

I.R Remote (purchased separately: LEDJ90B)

Functions:

The “BLACKOUT” button is used to set the LED’s into the power on or off modes.

The “AR” button is used to set the LED’s into the auto run mode.

The “S PR” button is used to set the LED’s to run the built-in programmes

The “FL” button is used to set the LED’s to flash on and off, to change the flash frequency use the “+” and “-” buttons.

The “SP” button is used to set the run speed, this button is available only in the colour change or colour fade modes. To change the speed use the “+” and “-” buttons.

The “D” button is used to set the LED’s into DMX mode. (See DMX value table)

The “SA” button is used to set the LED’s into sound activated mode. This function is unavailable on the Exterior Spectra Series.

The “SL” button is used to set the LED’s into slave mode.

The “S”, “0”, “1”, “2”, “3”, “4”, “5”, “6”, “7”, “8” and “9” buttons are used to set the DMX address for the LED’s. (see example below)

The “R”, “G”, and “B” buttons are used to set the brightness for the LEDs, to change the brightness use the “+” and “-” buttons.



1) Press the “S” button, so the red LED’s come on, this means you can now start

to set the DMX address.

2) Press the “2” button, so the green LED’s come on, this means the first digit

“2” (the hundreds place) setting is successful.

3) Now Press the “4” button, and the blue LED’s will come on, this now means

that the second digit “4” (tens place) setting is successful.

4) Now Press the “5” button, and all of the R/G/B LED’s will come on, this

means that the final digit “5” (units place) setting is successful and the full

DMX address setting has been changed.



1) Press the “S” button, so the red LED’s come on, this means you can now start

to set the DMX address.

2) Press the “0” button, so the green LED’s come on, this means the first digit

“0” (the hundreds place) setting is successful.

3) Now Press the “0” button, and the blue LED’s will come on, this now means

that the second digit “0” (tens place) setting is successful.

4) Now Press the “2” button, and all of the R/G/B LED’s will come on, this

means that the final digit “2” (units place) setting is successful and the full

DMX address setting has been changed.





• The maximum transmitter distance is 10M. Please make sure that you have the I.R remote

aimed directly at each fixture to be programmed,



9.


Xterior 60 CW/WW Operation modes

Built-in colour temperature macro mode

In this mode you can choose from its 17 preset built-in colour temperature colour macros. Simply press the “MODE” button to show “PRESET MODE”. Now press the “ENTER” button and use the

“UP” and “DOWN” buttons to choose your desired colour temperature. To add flash, press the “ENTER” button again and use the “UP” and “DOWN” buttons to set the speed from 00-99.

Flash value: 00 = Off, 99 = Fast

Dimming Mode:

In this mode you can set both of the Cool White LEDs and Warm White LEDs brightness individually. Press the “MODE” button to show “DIMMING”. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to adjust the brightness of Cool White (CW) from 00-99 and press the “ENTER” button again to adjust the brightness of the Warm White (WW) LEDs from

00-99. To add flash, press the

“ENTER” button again and use the “UP” and “DOWN” buttons to set the speed from 00-99.

Cool White values: 00 = Off, 99 = Full on

Warm White Values: 00 = Off, 99 = Full on

Flash value: 00 = Off, 99 = Fast

DMX mode:


“DOWN” buttons. Then to select one of the 2 DMX modes 2 or 5 channel, press the “ENTER” button again to choose the desired DMX mode by using the “UP” and


For the 2 or 5 channel DMX address information please see page 5


ALWAYS


Slave mode:




10.


Xterior 60 CW/WW DMX Charts


Channel

1

2

Value

0-255

0-255


Channel

1

2

3

4

5

Value

0-255

0-255

0-255

0-255

0-255

Function

Cool White 0-100%

Warm White 0-100%

Function

Cool White

Warm White

Master Dimmer


Colour temperature macros

11.


Xterior 60 CW/WW I.R. Remote functions

I.R Remote (purchased separately: LEDJ90D)

Functions:

The “BLACKOUT” button is used to set the LEDs into the power on or off modes.

The “D” button is used to set the LEDs into DMX mode. (See DMX value table)

The “FL” button is used to set the LEDs to flash on and off, to change the flash frequency use the “+” and “-” buttons.

The “SL” button is used to set the LEDs into slave mode.

The “S”, “0”, “1”, “2”, “3”, “4”, “5”, “6”, “7”, “8” and “9” buttons are used to set the DMX address for the LED’s.

The CW “50%”, “75%” and “100%” buttons are used to set the brightness for the Cool White LEDs, to change the brightness use the “+” and “-” buttons.

The WW “25%”, “50%”, “75%” and “100%” buttons are used to set the brightness for the Warm White

LEDs, to change the brightness use the “+” and “-” buttons.



1) Press the “S” button, so the Cool White LEDs come on, this means you can now start to set

the DMX address.

2) Press the “2” button, so the Warm White LEDs come on, this means the first digit “2”


3) Now Press the “4” button, and the Cool White LEDs will come on, this now means that the

second digit “4” (tens place) setting is successful.

4) Now Press the “5” button, and all of the Cool and Warm White LEDs will come on, this means


has been changed



1) Press the “S” button, so the Cool White LEDs come on, this means you can now start to set

the DMX address.

2) Press the “0” button, so the Warm White LEDs come on, this means the first digit “0”


3) Now Press the “0” button, and the Cool White LEDs will come on, this now means that the

second digit “0” (tens place) setting is successful.

4) Now Press the “2” button, and all of the Cool and Warm White LEDs will come on, this means


has been changed.





• The maximum transmitter distance is 10M. Please make sure that you have the

I.R remote aimed directly at each fixture to be programmed,



12.

Xterior Series DMX Set Up

DMX Set Up

DMX-512:

• DMX (Digital Multiplex) is a universal protocol used as a form of communication between

intelligent fixtures and controllers. A DMX controller sends DMX data instructions form the

controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the

DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only

have a data “out” terminal).

DMX Linking:

• DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller, as long as all fixtures and the controller are DMX compliant.

To ensure proper DMX data transmission, when using several DMX fixtures try to use the shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence the DMX addressing. For example; a fixture assigned to a DMX address of 1 may be placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain.

DATA Cable (DMX cable) requirements (for DMX operation):

• The Xterior Series can be controlled via DMX-512 protocol. The DMX address is set on the back of the unit or via specific I.R. remote (sold separately). Your fixture and your DMX controller require a 3-pin connector for data input/output.

Special Note: Line termination:

• When longer runs of cable are used, you may need to use a DMX terminator on the last unit to avoid erratic behaviour (LEDJ260).

13.

Xterior Series

IP Rated Power Cables

Optional Cables & I.R. Remotes

IP Rated DMX Cables

LEDJ137 - 1M

LEDJ138 - 2M

LEDJ139 - 5M

LEDJ140 - 10M

Interior to Exterior DMX cable

LEDJ141 - 1M

LEDJ142 - 2M

LEDJ143 - 5M

LEDJ144 - 10M

Exterior - Interior DMX Cable

LEDJ91 - 1M

Optional I.R. Remotes

LEDJ92 - 1M

LEDJ90B- RGB

For LEDJ157

LEDJ90C - RGBW/A

For LEDJ158

14.

LEDJ90D - CW/WW

For LEDJ159

USER MANUAL

www.prolight.co.uk

Xterior 24 Quad

Xterior 36 Tri

Xterior 60 CW/WW

USER MANUAL

Xterior 24 Quad Operation modes

Xterior 24 Quad DMX Charts

Xterior 24 I.R. Remote functions

Xterior 36 Tri Operation modes

Xterior 36 Tri DMX Charts

Xterior 36 Tri I.R. Remote functions

Xterior 60 CW/WW Operation modes

Xterior 60 CW/WW DMX Charts

Xterior 60 CW/WW I.R. Remote functions

Related manuals

LEDJ90B

LEDJ90A

Ledj

Xterior Wash 131

Ledj

RGBA SPECTRA BATTEN

SHOWTEC

LED Par 64 Short DMX