Acer Aspire easyStore easyStore Series, Altos easyStore M2 Home Server Příručka uživatele
Reklamë
Reklamë
Aspire easyStore Series
User Guide
Copyright © 2009 All Rights Reserved.
Aspire easyStore Series
User Guide
Model Name :
Part Number:
Purchase Date:
Place of Purchase:
iii
Safety instructions
Read these instructions carefully. Keep this document for future reference.
Follow all warnings and instructions marked on the product.
Turning the product off before cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
CAUTION for plug as disconnecting device
Observe the following guidelines when connecting and disconnecting power to the power supply unit:
Install the power supply unit before connecting the power cord to the AC power outlet.
Unplug the power cord before removing the power supply unit from the computer.
If the system has multiple sources of power, disconnect power from the system by unplugging all power cords from the power supplies.
CAUTION for Accessibility
Be sure that the power outlet you plug the power cord into is easily accessible and located as close to the equipment operator as possible. When you need to disconnect the power, be sure to unplug the power cord from the electrical outlet.
CAUTION for Listening
•
•
•
•
To protect your hearing, follow these instructions.
• Increase the volume gradually until you can hear clearly and comfortably.
Do not increase the volume level after your ears have adjusted.
Do not listen to music at high volumes for extended periods.
Do not increase the volume to block out noisy surroundings.
Decrease the volume if you can't hear people speaking near you.
iv
•
•
Warnings
Do not use this product near water.
Do not place this product on an unstable cart, stand or table. If the product falls, it could be seriously damaged.
•
•
•
•
•
•
Slots and openings are provided for ventilation to ensure reliable operation of the product and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface.
This product should never be placed near or over a radiator or heat register, or in a built-in installation unless proper ventilation is provided.
Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind onto or into the product.
To avoid damage of internal components and to prevent battery leakage, do not place the product on a vibrating surface.
Never use it under sporting, exercising, or any vibrating environment which will probably cause unexpected short current or damage rotor devices, HDD, Optical drive, and even exposure risk from lithium battery pack.
The bottom surface, areas around ventilation openings and AC adapter may get hot. To avoid injury, ensure they do not come in contact with yourskin or body.
Your device and its enhancements may contain small parts. Keep them out of the reach of small children.
Using electrical power
•
•
This product should be operated from the type of power indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company.
Do not allow anything to rest on the power cord. Do not locate this product where people will walk on the cord.
• If an extension cord is used with this product, make sure that the total ampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure that the total rating of all products plugged into the wall outlet does not exceed the fuse rating.
v
•
•
Do not overload a power outlet, strip or receptacle by plugging in too many devices. The overall system load must not exceed 80% of the branch circuit rating. If power strips are used, the load should not exceed 80% of the power strip's input rating.
This product's power supply is equipped with a three-wire grounded plug.
The plug only fits in a grounded power outlet. Make sure the power outlet is properly grounded before inserting the power supply plug. Do not insert the plug into a non-grounded power outlet. Contact your electrician for details.
Warning! The grounding pin is a safety feature. Using a power outlet that is not properly grounded may result in electric shock and/or injury.
•
Note: The grounding pin also provides good protection from unexpected noise produced by other nearby electrical devices that may interfere with the performance of this product.
The system can be powered using a wide range of voltages; 100 to 240 V
AC. The power cord included with the system meets the requirements for use in the country/region where the system was purchased. Power cords for use in other countries/regions must meet the requirements for that country/region. For more information on power cord requirements, contact an authorized reseller or service provider.
Product servicing
Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks. Refer all servicing to qualified service personnel.
•
•
•
•
•
Unplug this product from the wall outlet and refer servicing to qualified service personnel when: the power cord or plug is damaged, cut or frayed liquid was spilled into the product
• the product was exposed to rain or water the product has been dropped or the case has been damaged the product exhibits a distinct change in performance, indicating a need for service the product does not operate normally after following the operating instructions
vi
Note: Adjust only those controls that are covered by the operating instructions, since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal condition.
Disposal instructions
Do not throw this electronic device into the trash when discarding.
To minimize pollution and ensure utmost protection of the global environment, please recycle. For more information on the Waste from Electrical and
Electronics Equipment (WEEE) regulations, visit http://global.acer.com/about/sustainability.htm
vii
Regulations and safety notices
FCC statement
This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
•
•
However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna
Increase the separation between the device and receiver
•
Connect the device into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced radio/television technician for help
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.
Notice: Peripheral devices
Only peripherals (input/output devices, terminals, printers, etc.) certified to comply with the Class A limits may be attached to this equipment. Operation with noncertified peripherals is likely to result in interference to radio and TV reception.
Caution
Changes or modifications not expressly approved by the manufacturer could void the user’s authority, which is granted by the Federal Communications
Commission, to operate this server.
Notice Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
viii
Remarque à l'intention des utilisateurs canadiens
Cet appareil numérique de la classe B est conforme a la norme NMB-003 du
Canada.
Compliant with Russian regulatory certification
ix
Acer Incorporated
333 West San Carlos St. San Jose,
CA 95110, U.S.A.
Tel: 254-298-4000
Fax: 254-298-4147 www.acer.com
Federal Communications Commission
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
The following local Manufacturer/Importer is responsible for this declaration:
Product:
Model number:
Server
Aspire easyStore Series, Altos easyStore M2
Name of responsible party: Acer America Corporation
Address of responsible party: 333 West San Carlos St.
San Jose, CA 95110
U.S.A.
Contact person:
Tel:
Fax:
Acer Representative
254-298-4000
254-298-4147
x
Acer Incorporated
8F, 88, Sec.1, Hsin Tai Wu Rd., Hsichih
Taipei Hsien 221, Taiwan
Declaration of Conformity
We,
Acer Computer (Shanghai) Limited
8F, 88, Sec.1, Hsin Tai Wu Rd., Hsichih, Taipei Hsien 221, Taiwan
Contact Person: Mr. Easy Lai
Tel: 886-2-8691-3089 Fax: 886-2-8691-3120
E-mail: [email protected]
Hereby declare that:
Product: Server
Trade Name: Acer
Model Number: Aspire easyStore Series,
Altos easyStore M2
Is compliant with the essential requirements and other relevant provisions of the following EC directives, and that all the necessary steps have been taken and are in force to assure that production units of the same product will continue comply with the requirements.
EMC Directive 2004/108/EC as attested by conformity with the following harmonized standards:
• EN55022: 2006, AS/NZS CISPR22: 2006, Class B
• EN55024: 1998 + A1: 2001 + A2:2003
• EN55013:2001 + A1:2003 + A2:2006 (Applicable to product built with TV tuner module)
• EN55020:2007 (Applicable to product built with TV tuner module)
• EN61000-3-2: 2006, Class D
• EN61000-3-3: 1995 + A1: 2001+A2: 2005
Low Voltage Directive 2006/95/EC as attested by conformity with the following harmonized standard:
• EN60950-1: 2001 + A11: 2004
• EN60065: 2002 + A1: 2006 (Applicable to product built with TV tuner module)
Council Decision 98/482/EC (CTR21) for pan- European single terminal connection to the Public Switched Telephone Network (PSTN).
RoHS Directive 2002/95/EC on the Restriction of the Use of certain Hazardous
Substances in Electrical and Electronic Equipment
The standards listed below are applied to the product if built with WLAN module or wireless keyboard and mouse.
R&TTE Directive 1999/5/EC as attested by conformity with the following harmonized standard:
• Article 3.1(a) Health and Safety
•
•
EN60950-1:2001 + A11:2004
EN50371:2002
• Article 3.1(b) EMC
•
•
EN301 489-1 V1.6.1
EN301 489-3 V1.4.1 (Applicable to non-bluetooth wireless keyboard mouse set)
• EN301 489-17 V1.2.1
• Article 3.2 Spectrum Usages
• EN300 440-2 V1.1.2 (Applicable to non-bluetooth wireless keyboard mouse set)
•
•
EN300 328 V1.7.1
EN301 893 V1.4.1 (Applicable to 5GHz high performance RLAN)
Year to begin affixing CE marking 2009.
xi
January 7, 2009
Date
Easy Lai, Manager
Regulation Center, Acer Inc.
xii
1 Introduction
2 Setting up the system
Install the Windows Home Server Connector on the first computer
Install the Windows Home Server Connector on the client computers
Connect to the Home Server Console
11
3 Windows Home Server Console
Hardware Health and Performance Monitor
McAfee Total Protection Service
37
1
xiv
4 Managing the server
Configure backup for home computers
Configure the home server for remote access
Access the Aspire easyStore Series home page
Access the shared folders on the home server
Using the one-touch USB backup feature
Set up Wake On LAN on the home server
Set the home server uptime and down time
Monitor server health and performance
Explore the Windows Home Server icon
5 Configuring the hard disk drive
Replacing a failed hard disk drive
6 Troubleshooting
Recovering or restoring the home server
Update your home server with Aspire easyStore Series
Specific problems and corrective actions
117
63
107
1 Introduction
Thank you for choosing Aspire easyStore Series.
The Aspire easyStore Series is a data storage and digital media content server for your digital home. Featuring an Intel® Atom™ processor, up to 2 GB memory, four-drive hot-swap bay*, Gigabit Ethernet, eSATA and four USB ports for extended storage, a USB backup port for backing up data from a USB storage device, and a recovery/reset button to recover from a system failure or reset the system to factory default.
Aspire easyStore Series can store and share all your important data while simultaneously streaming digital media content to multiple applications including Apple iTunes or any Universal Plug and Play
(UPnP) Audio/Video and Digital Living Network Alliance™ (DLNA) compliant device, such as PS3 or Xbox 360. It allows you to consolidate your content library yet maintain instant access to digital media.
1
* Only hard disk drives installed in the drive bays 2, 3, and 4 are hot-swappable. The
2 1 Introduction
Features
• Powerful processor with excellent file sharing performance.
• Fast network performance in the home is delivered through a
Gigabit Ethernet connection.
• Equipped with Microsoft’s Windows Home Server operating system to help you centralize and connect your digital assets.
•
• Easily access your music, photos, and videos from virtually any
Internet connected computer on a home network or while away
from home. See “Access the shared folders on the home server” on page 81 for more information.
• One-touch USB backup feature enables quick and easy backup of
your data from a USB storage device. See “Using the one-touch
USB backup feature” on page 91 for more information.
•
•
•
Remotely wakeup the home server. See “Set up Wake On LAN on the home server” on page 93.
Specifications
Processor
Chipset
Drive storage
Memory
Ethernet
I/O ports
Intel® Atom™ Processor
Intel 945GC Express Chipset and ICH7R
Up to four 3.5-inch hot-swappable SATA hard disk drives
(HDD)
Up to 2 GB DDR2 MHz unbuffered SDRAM
High performance (10/100/1000) Gigabit Ethernet port
USB 2.0 ports (1 front and 4 rear), Gigabit Ethernet port, eSATA port, recovery/reset button
200 W, 100-240 V AC
Windows Home Server
Power
Server operating system (OS) support
Home computer OS support
Windows Vista 32-bit and 64-bit Edition
Windows XP 32-bit and 64-bit Edition
Digital media player support
Digital media file support
Any DLNA certified device
Physical dimensions
• Music: MP3, WMA, WAV, AAC, AC3, FLAC, APE, OGG,
VOC, AIFF, AU, MID
• Video: WMV, ASF, MOV, AVI, MPEG, 3GP, SWF, FLV,
RMVB, RM, RA, RAM, MP4, MPG, MPE, M2V, TP, TS,
MLV, MKV, DIVX
• Photos: GIF, PNG, BMP, JPG, JEPG, ICO, TIFF, DXF,
WMF, EMF, PICT, EPS, CDR
WxHxD: 200 x 180 x 212 mm
Weight (without HDD): 4.5 kg
(with 1 HDD): 5.1 kg
3
4
Overview
Front view
1 Introduction
2
3
4
5
6
7
No.
1
8
Icon Component
Power button/power indicator
Network indicator
Hard disk drive (HDD) status indicator
System status indicator
USB backup button/USB backup indicator
USB 2.0 port
Front door
Open the door to access the hot-swappable HDDs
HDD access indicators
Rear view
4
5
6
2
3
No.
1
Icon Component
Recovery/reset button eSATA port
USB port
Gigabit Ethernet port
Power connector
System fan
5
6
System LED indicators
1 Introduction
Front panel LED indicators
The LED indicators mounted on the front panel provide information about the status of the system, its hard drives, and network connection.
No.
Indicator
1 Power button
2 Network
Color
Blue
Blue
Red
State
On
Description
System is connected to the power supply and turned on and ready for use
Random blink
• System is booting
• System is in S3 sleep state
(suspend to memory)
Off • System is not powered on
• System initialize operation in progress
Link between system and network On
Random blink
Network access
Off Network disconnected
7
No.
Indicator
3 HDD status
(4)
Color State
Purple On
Description
• System not initialized
• HDD is not mounted into the drive bay
Random blink
• HDD is mounted into the drive bay and is in the process of being manually added into the server storage
• HDD is in the process of being removed from the server storage.
For detailed instructions on how to add or remove a drive from the
server storage, see “5 Configuring the hard disk drive” on page 107.
Blue
Red
None
On HDD is mounted into the drive bay and added into the server storage
For detailed instructions on how to add a drive into the server storage,
see “Adding a hard disk drive” on page 107.
Random blink
• HDD failure
• Windows Home Server cannot find HDD
Off No HDD mounted in the drive bay.
8 1 Introduction
No.
Indicator
4
5
6
USB device backup
HDD access
Color
System status Blue
Blue and
Purple
Red
Blue
Blue
State Description
Random blink
• System is booting
• System is shutting down
On System initialize operation completed.
Random blink
System is booting from a USB device
(Reserved for BIOS update while boot block has been active)
On May indicate the following states:
• System failure
• HDD failure
• SATA controller failure
• USB controller failure
• LAN controller failure
• FAN failure
• Memory failure
• Boot device not found
• If your network status is at risk
Random blink
System recovery or reset is in progress
On • USB storage device is connected to the USB port
• Backup completed
Random blink
System is backing up files from a
USB storage device
For detailed instructions on how to back up files from a USB storage
device, see “Using the one-touch
USB backup feature” on page 91.
Off
Blink
Off
USB storage device unmounted
HDD is in use
No HDD activity
Gigabit Ethernet port LED indicators
9
No.
Indicator
1 Speed indicator
2 Link/ activity indicator
Color
None
Green
Amber
Green
State
Off
On
On
Description
10 Mbps connection
100 Mbps connection
1000 Mbps connection
On Network link is detected
Random blink
Transmit or receive activity
Off No network connection
10 1 Introduction
2 Setting up the system
Follow these steps to set up Aspire easyStore Series to run in your home network.
•
•
Select a location for the home server
•
•
•
•
•
Install the Windows Home Server Connector on the first computer
•
Install the Windows Home Server Connector on the client computers
•
Connect to the Home Server Console
11
12 2 Setting up the system
Check package contents
Check the following items from the package:
• Aspire easyStore Series system
• Power cord
• Network cable
• Aspire easyStore Series Installation discs
• Software Installation Disc
Use this disc to do the following:
Install the Windows Home Server Connector software.
-
Install the Lights Out Client. Refer to “Set up Wake On LAN on the home server” on page 93.
Update system driver, BIOS, and add-in softwares. Refer to
“Update your home server with Aspire easyStore Series
• Server Recovery Disc - Use this disc to recover your home server after a system failure or restore the home server to its
• PC Recovery Disc - Use this disc restore a home computer from
• Quick Start Guide
• Warranty card
If any of the above items are damaged or missing, contact your reseller or retailer from which you purchased this product.
Select a location
Before unpacking and installing the system, select a suitable site for the system for maximum efficiency. Consider the following factors when choosing a site for the system:
• Near a grounded power outlet
• Clean and dust free
• Stable surface free from vibration
• Well-ventilated and away from sources of heat
• Secluded from electromagnetic fields produced by electrical devices such as air conditioners, radio, TV transmitters, etc.
13
14 2 Setting up the system
Recommended environment
For best results, your computer should meet the following hardware and software requirements:
• Processor
• 1 GHz Pentium 3, Pentium 4, AMD x64, or newer processor
• System memory
• 512 MB or above
• Hard drives
• 80 GB internal (ATA, SATA, or SCSI) as primary drive
• Operating system
• Windows Vista Home Basic
• Windows Vista Home N (EU only)
• Windows Vista Home Premium
• Windows Vista Business
• Windows Vista Business N (EU only)
• Windows Vista Enterprise
• Windows Vista Ultimate
• Windows XP Home with Service Pack 2 (SP2)
• Windows XP Professional with SP2
• Windows XP Media Center Edition 2005 with SP2 and Rollup 2
• Windows XP Media Center Edition 2004/2005 with SP2
• Windows XP Tablet Edition with SP2
• Web browsers
• Internet Explorer version 6.0, 7.0, or above
• Mozilla Firefox 1.5 or above
• Internet connection
• 100 Mbps to 1000 Mbps Gigabit Ethernet connection
• Broadband connection (DSL or cable)
• Broadband router (DHCP enabled and meets UPnP standards.)
• Digital media player for streaming media files
• iTunes 7.1 or later
• Windows Media Player 10 or later
15
Connect the power cord
Plug the power cord into the power connector and the other end into an electrical outlet.
16 2 Setting up the system
Connect to the home network
Important: Connect the Aspire easyStore Series to your broadband router with a network cable. Wireless connection to your broadband router is not supported. However, home computers that are connected through a wireless connection is supported.
Connect one end of the network cable into the network port and the other end to a Gigabit Ethernet port on a broadband router.
Power on the system
After making sure that you have set up the system properly and connected all the required cables, you can now power on the system.
Press the power button to turn system on. The LED indicators on the front panel will flash, change colors and turn to solid blue after startup.
17
Note: During initial startup, the system status indicator on the front panel will flash red and turn to solid blue. This is a normal power-up sequence. Wait for all the LED indicators to turn solid blue before proceeding to the next section.
To power down the system, press and hold the power button down for at least four seconds.
18 2 Setting up the system
Install the Windows Home Server
Connector on the first computer
After setting up your Aspire easyStore Series, you must install the
Windows Home Server Connector on your computer.
Note: Prior to installing the Windows Home Server Connector, make sure you have administrator privileges. Refer to the
Windows Help for more details on changing your user account settings.
1 Place the Aspire easyStore Series Software Installation Disc in the optical drive of the first home computer. The installation wizard starts.
Or, double-click on the Client Installation.exe file to begin installation. The Welcome window appears.
2 Click Install the software on the computer and then click Next.
19
3 Click Install to begin the installation process. The Microsoft .Net
Framework 2.0 and Windows Installer 3.1 components are installed.
20 2 Setting up the system
After the components are installed, the Windows Home Server
Connector installation starts to find and connect to your Aspire easyStore Series.
Once the server is found, the Welcome window appears.
4 Click Next.
5 Click Next.
6 Select the “Download the updates from my home server and install them automatically” option button if you want to download the updates for the Connector.
21
22 2 Setting up the system
Note: Performing the initial Windows Update automatically may take up to one hour. You may select Let me download and install the updates myself to speed up the process.
7 Click Next.
8 Select the “Yes, wake up this computer if it is in sleep or hibernate mode and back it up” option button if you want Windows Home
Server to wake up your sleeping computer to back it up.
23
9 Click Next.
10 Click Next to perform an initial configuration of the home server.
Note: The initial configuration of the home server is performed once on the first home computer.
24 2 Setting up the system
Note: You will not be able to perform the initial configuration on a default resolution of 1024 x 600. You will need to switch to a higher resolution before doing the initial configuration.
11 Click the Next arrow. The Windows Home Server initialization begins and could take several hours depending on your hardware.
12 Once the initialization is completed, click the Next arrow.
25
13 Enter a name for your home server.
The name of your home server can contain a maximum of 15 characters (includes letters, numbers or hyphens) with no spaces.
14 Click the Next arrow.
15 Enter a strong Windows Home Server administrator password, confirmation password, and a password hint. This is the password that you can use to manage your home server from the Windows
Home Server Console.
The strong password must be at least 7 characters and must contain at least three of the following four categories:
• Uppercase letters
• Lowercase letters
• Numbers
• Symbols (such as !, @, #, etc.)
An example of a strong password is Acer123.
Caution:
1. Keep the administrator password for the server in a safe place.
You will not be able to log on to the server if you enter a wrong password. If you forget the password, you will have to restore the server, and all system settings, user accounts and data will be lost.
2. Restoring the server requires a wired connection between the
26 2 Setting up the system server and client PC. Connect the two and insert the Server
Recovery Disc into the client PC's optical drive to start the process.
16 Click the Next arrow.
17 Select the “User recommended settings” option button if you want to use Windows Update to automatically download and install updates for Windows Home Server, then click the Next arrow.
18 Choose if you want to participate in the Customer Experience
Improvement program, then click the Next arrow.
27
19 Choose if you want to participate in the Windows Error Reporting program, then click the Next arrow.
28 2 Setting up the system
20 Click the Next arrow to automatically download and install available Windows Home Server updates. This could take some time to complete but will not need additional information from you.
Important: Do not restart or turn off your home server during the update process.
21 Once installation is complete the Windows Home Server windows displays.
22 Click the Next arrow. The Windows Home Server log in window displays. You can now manage the home server through the remote admin console.
29
23 Enter the administrator password, then click the Next arrow. The
Setting Password dialog box appears.
30 2 Setting up the system
24 Enter the administrator password to start the hardware health and performance monitor service, then click OK. The Windows Home
Server Console window appears.
The Windows Home Server icon also appears in the system task tray and the Shared Folders desktop shortcut appears on your desktop.
The Windows Home Server icon displays the current health and status of the home server as well as all the computers connected to your home network. Right-clicking on the icon allows access to the
Windows Home Server. For more information about the system
tray icon refer to “Explore the Windows Home Server icon” on page 105.
You can also use Shared Folders to store and organize files on the home server.
31
Install the Windows Home Server
Connector on the client computers
After installing the Windows Home Server Connector on the first computer, use the Aspire easyStore Series Software Installation Disc to install the Windows Home Server Connector on the computers you want to connect to your home server.
If you have misplaced the disc, you can install the Windows Home
Server Connector via the home server. Refer to page 33 for detailed
instructions.
To install the Windows Home Server connector from the Aspire easyStore Series Software Installation Disc
1 Place the Aspire easyStore Series Software Installation Disc in the optical drive of the client computer. The installation wizard starts.
Or, double-click on the Client Installation.exe file to begin installation. The Welcome window appears.
2 Click Next.
3 Click Install to begin the installation process. The Microsoft .Net
Framework 2.0, Windows Installer 3.1, and Acer Update, and
Aspire easyStore Series components are installed.
32 2 Setting up the system
4 After the components are installed, the Windows Home Server
Connector installation starts to find and connect to your home server.
Once the home server is found, the Welcome window appears.
5 Click Next.
6 Read the End-User License Agreement. If you agree with the terms of the agreement, then select the “I accept the terms of the license agreement” option button.
7 Click Next. The installation status window appears.
8 Click Next.
9 Enter the Windows Home Server administrator password.
10 Click Next and follow all onscreen instructions until you finish installation.
11 Once installation is complete the Windows Home Server icon appears in the system task tray and the Shared Folders desktop shortcut appears on your desktop.
33
To install the Windows Home Server connector directly from the home server
1 Open a Web browser.
2 In the address bar, enter http://Aspirehome:55000/, where
“Aspirehome” is the name of the home server.
3 Under Windows Home Server Connector Setup, click Download
Now.
4 In the File Download dialog box, click Run.
5 Follow all onscreen installation instructions until you finish installation.
34 2 Setting up the system
Connect to the Home Server
Console
In order to remotely administer the home server, you need to log onto the Windows Home Server Console.
Note: Make sure you have the administrator password to the home server.
There are three ways to launch Windows Home Server Console -
Windows Start menu, double-clicking the Windows Home Server icon, or right-clicking the Windows Home Server icon.
To log onto the home server using Windows Start menu:
1 On your computer, click Start > Programs > Windows Home Server
Console.
2 Enter the administrator password, then click the Next arrow.
35
To log onto the home server using Windows Home Server icon:
1 Right-click on the Windows Home Server icon in the system tray, then select Windows Home Server Console from the pop-up menu.
Or,
Double-click the Windows Home Server icon in the system tray.
2 Enter the administrator password, then click the Next arrow.
36 2 Setting up the system
3 Windows Home
Server Console
37
The Windows Home Server Console is a tool that provides remote management of the home server and allows you to monitor and backup computers on the home network. It allows you to remotely administer your home server from anywhere on the home network.
Once logged in, you can monitor the health of the home server and connected computers on the network, create backup schedules connected to the computers, backup computers, and manage user accounts, shared folders on the server.
Windows Home Server Console provides access to the following tabs:
• Computers and Backup
• User Accounts
• Shared Folders
• Server Storage
• Lights Out
• McAfee Total Protection
• System Information
• Network Health
• Settings
To learn more about configuring the Windows Home Server, click Help on the console to open the Windows Home Server Console Help.
38 3 Windows Home Server Console
Computers & Backup
You can use the Computers & Backup tab on the Windows Home
Server Console to view the home computers connected to the home server and monitor the health status of the home computers and administer backups. After you install Windows Home Server Connector on each of your home computers, they are automatically backed up on each night to your home server.
The options on the Computers & Backup tab allow you to:
• View Backups - Browse the existing backups of a home computer.
• Backup Now - Initiate manual backup of a home computer.
• Configure Backup - Change the backup settings of a home computer.
• Remove Computer - Delete computer and backups from the home server.
For more information, see Computers & Backup in the Windows Home
Server Console Help.
39
User Accounts
You can use the User Accounts tab on the Windows Home Server
Console to create a personal user account, enable a guest account, and maintain user accounts on the home server.
The options on the User Accounts tab allow you to:
• Add - Create a new user account on the home server and set access rights for the user.
• Properties - View and change user account properties.
• Remove - Delete a user account from the home server.
For more information, see User Accounts in the Windows Home Server
Console Help.
Note:
1. You can only have full access to the shared media folders
(Video/Photo/Music) after creating user accounts. Otherwise, you can only read files but not save files to the home server.
2. A personal shared folder is created each time you add a new user account. By default, only this user account has access to the personal shared folder. Users can store personal files in their personal shared folder. This is true even if the guest account is enabled.
40 3 Windows Home Server Console
Shared Folders
You can use the Shared Folders tab on the Windows Home Server
Console to add, open, remove, and view shared folders on the home server. With Shared Folders you can centrally store files on your home server so that you can share with other people on your home network.
The following shared folders are created automatically on the home server:
• Music
• Photos
• Public
• Software
• Videos
• A personal shared folder for each personal user account that is added. By default, no other user account can access this personal shared folder
41
The options on the Shared Folders tab allow you to:
• ADD - Create a new shared folder on the home server.
• VIEW/CHANGE - View and change shared folder properties.
• OPEN - Browse files and folders in the shared folder.
• REMOVE - Delete an existing folder from the home server.
For more information, see Shared Folders in the Windows Home Server
Console Help.
42 3 Windows Home Server Console
Server Storage
The Server Storage tab on the Windows Home Server Console displays all the hard drives installed on your home server. You can use Server
Storage to view, add, repair, and remove hard drives from the home server.
The options on the Server Storage tab allow you to:
• Add - You can add hard drives of various sizes to the home server and set the hard drives for the following usage:
• Server storage - This option gives you more space to store home computer backups and more space for your shared folders.
• Server Backup - This option allows you to back up all your home server shared folders. If you use an external hard drive for your home server backups, you can store the hard drive in a separate location. When you select this option, your home server appears in the Computers & Backup tab. You can use
Back up Now to back up your shared folders to the hard drive.
• Repair - Fix errors on an unhealthy hard drive.
• Remove - Delete a hard drive from the home server.
For more information, see Server Storage in the Windows Home Server
Console Help.
43
Lights Out
Lights Out is a power management add-in software that allows you to set the home server into suspend mode or wake the system at a chosen time with the aid of a calendar event.
The Lights Out tab include the following options:
• Refresh - Ensures you have the most resent version of the uptime diagram.
• Update diagram - Displays a chart showing recorded uptimes in the home server, such as when a backup took place, which home computer was active, or when the home server woke up from sleep mode.
• Calendar - Displays the calendar window and allows you to add, edit, delete a calendar entry.
• Settings - Displays the Windows Home Server Settings dialog box
For more information on how to configure the Lights Out settings,
• About - Displays version number and copyright information.
For more information, click Help in the Lights Out window.
44 3 Windows Home Server Console
McAfee Total Protection
McAfee Total Protection is an add-in software for Windows Home
Server. It is a comprehensive security management solution that checks for viruses, spyware, unwanted programs, and other potential threats on the home server.
Note: Before you can schedule a scan or have the home server virus pattern updated, you must activate the McAfee Total
Protection Service
You can perform the following tasks in the McAfee Total Protection tab:
• Launch SecurityCenter
• Update Now
• About
• Schedule a Scan
• Manage PUP Detections
• View Quarantined Files
For more information, click Help in the McAfee Total Protection window.
45
System Information
The System Information tab on the Windows Home Server Console provides an all around monitoring mechanism to help you keep an eye on the home server’s health and performance details.
System Information supports the following features:
• Acer Aspire easyStore Home Server - Displays basic information about the home server, such as the specification of the processor and memory currently installed in the home server, BIOS version, and operating system version.
• LED Brightness - Allows you to adjust the brightness of the LED indicators on the home server.
46 3 Windows Home Server Console
• Remotely Wake Up Aspire easyStore Home Server - Allows you to enable or disable remote wakeup feature.
• Hardware Performance and Health Monitor - Allows you to view the performance data of the home server, and monitor the temperature, voltage and fan speed.
To adjust the LED brightness of the home server:
On the LED Brightness field, drag the slider in a horizontal manner to a desired position.
Note: When you restart the Home Server, the LED brightness will revert back to its default settings.
To enable or disable the remote wake up feature:
1 On the Remotely Wake Up Aspire easyStore Home Server field, click the “Enable” check box to wake the home server from sleep mode. It allows users, who want to upload files, to wake the system from sleep mode.
2 Click the “Disable” check box to disable this feature.
For more information, refer to Network Health in the Windows Home
Server Console Help.
Network Health
The Network Health tab displays health notifications from your home server and your home computers. You can view the health of your entire network from one convenient location so you can take the necessary actions to correct any problems.
47
Note: Health notifications are also displayed in the Windows
Home Server icon on home computers that have the Windows
Home Server Connector software installed.
The possible health states are as follows:
Color Status
Indicates a healthy network.
48
Color
3 Windows Home Server Console
Status
Indicates an at-risk issue that you must attend soon.
Indicates a critical issue that you must attend to immediately.
For more information, right-click the Windows Home Server icon, click
Help.
Settings
The Settings button on the upper right hand corner of the Windows
Home Server Console window allows you to configure your home server settings. The Settings window provides a variety of administrative options.
49
In the Settings window you can configure the settings for the following categories:
• General
• Backup
• Passwords
• Media Sharing
• Remote Access
• Add-ins
• Hardware Health and Performance Monitor
• IP Configuration
• Lights Out
• McAfee Total Protection Service
50
• Settings for DMS
• Settings for iTunes Server
• Resources
3 Windows Home Server Console
General
The General settings page allows you to modify the date and time, language selection, Windows Update settings, Customer Experience
Improvement program, and enable or disable Windows error reporting.
For information about the tasks that you can perform on the General settings page, click the Help button on the lower right hand corner of the General page.
Backup
The Backup settings page allows you to configure the start and end time for backing up computers on the home network, specify the number of months, weeks, and days to keep backups on the home server, and manually clean up old backups.
51
For information about the tasks that you can perform on the Backup settings page, click the Help button on the lower right hand corner of the Backup page.
52 3 Windows Home Server Console
Passwords
Use the Password settings page to change the home server password and modify the user accounts password policy.
For more information, click the Help button on the lower right hand corner of the Passwords page.
Media Sharing
The Media Sharing settings page allows you to enable or disable
Windows Home Server media sharing capabilities.
53
For information, click the Help button on the lower right hand corner of the Media Sharing page.
54 3 Windows Home Server Console
Remote Access
The Remote Access settings page helps you configure everything you need to access the Aspire easyStore Series home page from the
Internet. To get remote access up and running, you must turn on Web
Site Connectivity, configure your router, configure a domain name for your home server, and set the Aspire easyStore Series home page.
For more information, click the Help button on the lower right hand corner of the Remote Access page.
Add-ins
The Add-ins settings page allows you to configure the add-in software that you have installed or want to install on your home server.
For information on how to install an add-ins, click the Help button on the lower right hand corner of the Add-ins page.
55
Hardware Health and Performance Monitor
Use the Hardware Health and Performance Monitor settings page to set a refresh interval for monitoring data, configure performance threshold settings, specify email destinations to which alerts should be sent when temperature, voltage, and fan speed abnormality is detected or the pre-configured threshold is exceeded.
In the Hardware Health and Performance Monitor page, you can configure the following settings:
• Auto Refresh - Sets the refresh interval to tell Windows Home
Server how frequent the monitoring data should be performed.
• Performance settings - Sets the performance threshold of the CPU,
Memory and Storage.
• E-Mail alert setting - Specify an email address to which alerts should be sent.
• Launch SMTP setup - Configure the Simple Mail Transport setup.
To validate the email alert feature, it is required that you properly
For more information, click the Help button on the lower right hand corner of the Hardware Health and Performance Monitor page.
56 3 Windows Home Server Console
IP Configuration
The IP Configuration settings page allows you to view the home server’s current IP configuration settings or change the IP configuration manually.
For more information, click the Help button on the lower right hand corner of the IP Configuration page.
57
Lights Out
Use the Lights Out page to define times where the home server has to go to suspend or resume mode.
In the Lights Out page, you can configure the following settings:
• Client computer monitoring - Client computer monitoring is used to check periodically for active clients. When no active clients are detected, the selected action will be executed after the wait time.
You can choose to disable client monitoring, put your server to suspend or hibernate mode, or shut down the server.
• Options - You can set Lights Out to wake up your home server on a configured backup time. You should enable this option when you run regular backups.
• Uptime diagram - Recorded uptimes are visualized in the uptime chart. You can choose between a history range of 2 to 14 days.
When your server is always up, you can exclude the server from the chart. In the same way you can configure the display of backup times.
When the monitoring for remote access is enabled, the default action is disabled as long as a remote user is logged in. The default timeout from the home server is set to 20 minutes. Lights Out waits 3 additional minutes after timeout.
For more information, click the Help button on the lower right hand corner of the Lights Out page.
58 3 Windows Home Server Console
McAfee Total Protection Service
Use the McAfee Total Protection Service page to manage security for your home server.
For more information, click the Help button on the lower right hand corner of the McAfee Total Protection Service page.
59
Settings for DMS
The Settings for DMS (Digital Media Server) page allows you to enable or disable digital media server function and customize the sorting method of photos and videos.
With DMS enabled, digital media controllers and digital media players using UPnP (Universal Plug’n Play) protocol, will automatically discover, access, and play media files on the home server. It also makes possible for iTunes, PS3, or Xbox 360 users to share media files on Windows
Home Server.
In the Settings for DMS, you can configure the following settings:
• Digital Media Server - Enables or disables the digital media server.
• Sorting method - Select a sorting method to organize digital files under the photos or videos shared folders.
For more information, click the Help button on the lower right hand corner of the Settings for DMS page.
60 3 Windows Home Server Console
Settings for iTunes Server
The Settings for iTunes Server page allows you to enable or disable the iTunes server function, specify how often the music library is updated, set a password to secure the iTunes Server access.
For more information, click the Help button on the lower right hand corner of the Settings for iTunes Server page.
61
Resources
You can use the Resources page to view the following information about your home server:
• Microsoft Windows - Activates Windows Home Server and allows you to view the Microsoft Software License Terms.
• Home Server - Displays information about your home server hardware.
• Version Information - Displays the version of the Windows Home
Server services that are running on your home server.
• Learn More - Displays additional Windows Home Server links.
• Support - Displays the Product Support link.
Shut Down
The Shut Down button on the left pane allows you to shut down
Windows Home Server so that you can safely turn off power or start
Windows Home Server again.
62 3 Windows Home Server Console
4 Managing the server
After you complete the Windows Home Server Setup and install the
Windows Home Server Connector software on all of your home computers, you can now perform the following tasks:
•
•
•
Configure backup for home computers
•
•
Configure the home server for remote access
•
Access the Aspire easyStore Series home page
•
Access the shared folders on the home server
•
•
•
•
•
Using the one-touch USB backup feature
•
Set up Wake On LAN on the home server
•
Set the home server uptime and down time
•
Monitor server health and performance
•
•
Explore the Windows Home Server icon
To learn more about using the Windows Home Server Console to
configure the home server, refer to “3 Windows Home Server Console” on page 37.
63
64 4 Managing the server
Create user accounts
After you complete Windows Home Server Setup and install the
Windows Home Server Connector software on all of your home computers, you are ready to set up your user accounts for the people in your household.
There are two types of user accounts that you can set up for the home server:
• Guest account - If you want everybody to use the same user account to access the home server, you must enable the guest account feature in the console.
• Personal user account - If you want an individual to access the home server with their own personal user account, you must add matching user accounts on Windows Home Server and give access privileges to individual shared folders.
To enable the guest account:
The guest account can be used to give access to shared folders for users that do not have their own user account for Windows Home Server.
Enabling the guest account will provide default Read permission to the shared folders: Music, Photos, Videos, Public, and Software.
Caution: If you enable the guest account, your home server is open to anyone who connects to your home network. They can access all of the shared folders and other resources on your home server.
1 Double-click the Windows Home Server icon in the system tray.
2 Log on to the Windows Home Server Console.
3 Click the User Accounts tab.
65
4 Under About Guests, click Enable Guest.
Caution: If you have a wireless network, secure it before you enable the guest account with no password. For more information, see the documentation for your wireless device.
5 Click OK.
66
To add a personal user account:
4 Managing the server
Note: A personal shared folder is created each time you add a new user account. By default, only this user account has access to the personal shared folder. Users can store personal files in this personal shared folder.
1 Double-click the Windows Home Server icon in the system tray.
2 Log on to the Windows Home Server Console.
3 Click the User Accounts tab.
4 Click Add.
5 On the User Accounts Setup window, click Set Policy to set a user accounts password policy.
6 Click OK.
7 Click Add.
8 Enter the user’s name.
Note: When you create user accounts on Windows Home Server, use logon names that match the logon names of your existing user accounts on your home computers. Also, use the same password that you use for your existing user accounts. If the user accounts and passwords do not match, you will be prompted for a user name and a password when you open the Shared folders.
9 Select the “Enable Remote Access for this user” check box if you want to allow the user to remotely access the home server.
10 Click Next.
67
68 4 Managing the server
11 Enter a password which must be at least 7 characters, then re-enter it in the Confirm password field.
12 Click Next.
13 Assign user rights to the shared folders on the home server.
• Full - The user can view, add, modify, and delete files in the shared folder.
• Read - The user can view files in the shared folder, but cannot add, modify, or delete files.
• None - The user cannot view, add, modify, or delete files in the shared folder.
14 Click Finish.
15 Click Done to exit the wizard.
Note:
1. You can only have full access to the shared media folders
(Video/Photo/Music) after creating user accounts. Otherwise, you can only read files but not save files to the home server.
2. A personal shared folder is created each time you add a new user account. By default, only this user account has access to the personal shared folder. Users can store personal files in their personal shared folder. This is true even if the guest account is enabled.
Add a shared folder
Shared folders are places for you to organize and store files on the home server so that you can share them with other people on your home network.
1 Double-click the Windows Home Server icon in the system tray.
2 Log on to the Windows Home Server Console.
3 Click the Shared Folders tab.
4 Click Add.
69
5 Enter a name and description for the shared folder.
6 Select the “Enable Folder Duplication” check box if you want folders and files in the share folder to be duplicated across multiple hard drives.
Note: The home server must have more than one hard drive added to the server storage before you can enable Folder Duplication and there must be enough storage space available for duplication to take place.
70
7 Click Next.
4 Managing the server
8 Assign user rights to the new share folder, then click Finish.
9 Click Done to exit the wizard.
Configure backup for home computers
You can customize the backup of each of your home computers from the Windows Home Server Console.
71
Note: After you install the Windows Home Server Connector to the home computer all hard drive volumes on the home computer are automatically backed up each night.
To configure backup for a computer:
1 Double-click the Windows Home Server icon in the system tray.
2 Log on to the Windows Home Server Console.
3 Click the Computers & Backup tab.
4 Complete the Backup Configuration Wizard to choose the volumes you want to back up and the folders you want to exclude from the backup.
You can adjust the period of time when automatic backups and maintenance are performed. The period of time that you choose should be a time when your home computers are normally not being used. The time period must be a least one hour long and can be up to 23 hours long. The default settings are Start Time: 12:00
AM and End Time: 6:00 AM.
72
Back up the home server
4 Managing the server
You can back up your home server to ensure that you have backup copies of important files that are located in your Windows Home
Server shared folders and application folders. You can add hard drives to your home server to use for server backups by using the Server
Storage tab.
To back up the home server:
1
Install a new hard drive to the home server. See step 1 of “Adding a hard disk drive” on page 107.
2 Double-click the Windows Home Server icon in the system tray.
3 Log on to the Windows Home Server Console.
4 Click the Server Storage tab.
5 Select the newly installed hard drive (either internal or external), then click Add to run the Add a Hard Drive Wizard.
73
6 Click Next.
7 Select the “Use this hard drive to back up files that are stored on your home server” option button.
8 Click Next.
74 4 Managing the server
9 Select if you want to preserve or format the hard drive, then click
Next.
10 Enter a name for the hard drive, then click Next.
Note: You can write this name on a label and attach it to your hard drive to help you identify it later.
11 Click Finish.
12 Click Done.
13 Click the Computers & Backup tab.
14 Select the Server Backup Hard Drive you want to use to back up your shared folders and application folders.
15 Click Back up Now.
16 Select a destination hard drive for each shared folder.
17 Click Back up Now.
18 Click Close.
75
76 4 Managing the server
Configure the home server for remote access
You must configure your home server for remote access to easily access your files and home computers from anywhere with an Internet connection. You can download files, upload files, connect to your home computers, and administer the home server.
To configure the home server for remote access:
Important: Only personal user accounts with remote access permissions can log on to the Aspire easyStore Series home page.
1 Double-click the Windows Home Server icon in the system tray.
2 Log on to the Windows Home Server Console.
3 Click Settings.
4 In the navigation pane, select RemoteAccess.
5 Under Web Site Connectivity, click Turn On to allow remote connection to the home server.
6 Under Router, click Setup to configure your broadband router.
Make sure your router supports UPnP standards and the UPnP
77 setting must be enabled on your router for Windows Home Server to automatically configure it.
In this step, Windows Home Server configures the persistent port forwarding from your UPnP certified router to your home server, as follows:
• Port 80 - Connects over your home network to the Aspire easyStore Series home page using the HTTP protocol.
• Port 443 - Connects over your home network to the Aspire easyStore Series logon page using HTTPS, an encrypted Secure
Sockets Layer protocol.
• Port 4125 - Connects to your home computers via the remote desktop proxy.
Note: To learn more about router configuration, click Help on the
Remote Access page.
7 Under Domain Name, click Setup to set a personalized domain name for your home server (For example, smithfamily.homeserver.com).
A domain name uniquely identifies your home server on the
Internet. It is used to connect to your home server while you are away from home. Even if your Internet IP address changes, you can still connect to your home network with your personalized domain name. For example, you could register the name smithfamily.homeserver.com and then use that name to connect to your Aspire easyStore Series Web site.
Note: You need a Windows Live ID to set up a domain name for your home server.
8 Click Next.
9 Enter your Windows Live ID email address and password to begin setting up the domain name.
Windows Home Server includes a built-in dynamic DNS client feature that binds your personalized domain name to the external
IP address that is assigned by your ISP (Internet service provider).
10 Click Next.
11 Click the “I accept” option, then click Next.
78 4 Managing the server
12 Enter the domain name and select a subdomain name.
13 Click Confirm to make sure the subdomain is available.
14 Click Finish.
15 Under Web Site Settings, you can choose a default home page and the Web site headline that appears on the Aspire easyStore Series
Web page.
16 Click OK.
17 After you configure remote access, test the remote connectivity
from outside of your home. Refer to “Access the Aspire easyStore
Access the Aspire easyStore Series home page
After you configure a user account for remote access, you can use a
Web browser on a computer that is outside your home to remotely access your home server and home computer.
On the Aspire easyStore Series home page, you can perform the following:
• Remotely access the Windows Home Server Console.
• Remotely access your home computers.
• Remotely download or upload files to shared folders.
79
Important: Use Internet Explorer to access and remotely administer your home server over the Web. Some features, such as accessing the home computers or the Windows Home Server
Console, are not available when you use other Web browsers.
To access the Aspire easyStore Series home page:
Note: You cannot use the guest or administrator account to access the home page. You must log on with a personal user account that is enabled for Remote Access.
1 Make sure the home server is configured for remote access. See
“Configure the home server for remote access” on page 76.
Note: You may need to add services from your broadband provider to use the remote access features in Windows Home
Server. For more information, refer to the Windows Home Server
Console Help.
2 Open the Internet Explorer Web browser.
3 Enter the Internet domain name assigned to you during the remote access setup procedures. For example https://
SmithFamily.HomeServer.com., where SmithFamily.HomeServer is the domain name that is assigned to the home server.
4 Click Log On on the upper right hand corner.
80 4 Managing the server
5 Enter your home server user name and password.
6 Click Log On.
The home page include three tabs:
• Home - This page appears every time you log on to the Web page.
• Computers - Allows you to perform remote administration on the home server and the home computers.
To access your home server, click Connect to your Home Server on the Computers tab and enter the administrator password.
The Windows Home Server Console interface opens.
To access your home computers, click the name of the home computer under the Remote Access to Computers field on the
Computers tab.
Note: Make sure that the home computer is configured to allow remote access. For detailed instructions about how to complete
this configuration, see “Can’t connect to some computers on the
Aspire easyStore Series Remote Access page” on page 133.
• Shared Folders - Allows you to access the shared folders you have access privileges over the Internet.
81
Access the shared folders on the home server
There are several ways you can access your shared folders on the home server.
To access the shared folders using the desktop shortcut:
1 Double-click the Shared Folders desktop shortcut to see the shared folders that are on your home server.
2 Double-click a shared folder to open it.
82 4 Managing the server
To access the shared folders using the Windows Home Server icon:
1 Right-click the Windows Home Server icon .
2 Click Shared Folders.
3 Double-click a shared folder in the window to open it.
To access the shared folders using the Windows Start Menu:
• In Windows Vista, click Start, then type \\homeservername in the
Start Search text box, where the homeservername (i.e.
Aspirehome) is the name of your home server. Double-click a shared folder in the window to open it.
• In Windows XP, click Start, click Run, and then type
\\homeservername in the Open text box, where the homeservername (i.e. Aspirehome) is the name of your home server. Double-click a shared folder in the window to open it.
83
To access the shared folders using the Internet:
1
Log on to the Aspire easyStore Series home page. See “Access the
Aspire easyStore Series home page” on page 79.
2 Click the Shared Folders tab.
3 You can navigate to a particular shared folder, then download or upload files to your home server.
84
Enable media sharing
4 Managing the server
The Windows Home Server allows you to stream music, photos, and videos from the home server to any supported digital media receiver, such as PlayStation 3, or to a supported digital media player, such as
Windows Media Player 11.
To enable media sharing:
1 Double-click the Windows Home Server icon in the system tray.
2 Log on to the Windows Home Server Console.
3 Click Settings.
4 In the navigation pane, select Media Sharing.
5 Select a folder, then click On.
6 Click OK.
85
Enable Digital Media Server
The Digital Media Server feature allows you to browse, access and play media contents on the home server. It makes possible for iTunes and
PlayStation 3 users to share media files on the home server.
The home server supports the following digital media files:
• Music: MP3, WMA, WAV, AAC, AC3, FLAC, APE, OGG, VOC, AIFF,
AU, MID
• Video: WMV, ASF, MOV, AVI, MPEG, 3GP, SWF, FLV, RMVB, RM,
RA, RAM, MP4, MPG, MPE, M2V, TP, TS, MLV, MKV, DIVX
• Photos: GIF, PNG, BMP, JPG, JEPG, ICO, TIFF, DXF, WMF, EMF, PICT,
EPS, CDR
To enable digital media server:
1 Double-click the Windows Home Server icon in the system tray.
2 Log on to the Windows Home Server Console.
3 Click Settings.
4 In the navigation pane, select Settings for DMS.
5 Under Digital Media Server, click the “Enable” option button.
6 Select a sorting method for the Photos and Videos shared folders.
86 4 Managing the server
• Sorting by Name - Photos and videos are arranged according to the original organization, which is the default option.
• Sorting by Date - Digital Media Server auto checks the latest modification dates of files and creates different virtual folders by year and subfolders by month.
7 Click OK.
87
Enable iTunes service
The Digital Media Server feature allows you to enable or disable the iTunes server function, specify how often the music library is updated, set a password to secure the iTunes Server access.
To enable iTunes service:
1 Double-click the Windows Home Server icon in the system tray.
2 Log on to the Windows Home Server Console.
3 Click Settings.
4 In the navigation pane, select Settings for iTunes Service.
5 Under iTunes Server, click the “Enable” option button.
6 Specify how often iTunes can scan the home server for new music files.
7 Enter a password to protect iTunes server.
8 Click OK.
88 4 Managing the server
Stream audio
You can use Windows Media Player 11 or iTunes to play music files stored on the home server to your computer.
To stream audio in Windows Media Player 11:
1
2
Make sure Digital Media Server is enabled. Refer to “Enable
Digital Media Server” on page 85 for more information.
3 Open the Windows Media Player.
4 Click the Library tab. The Acer Aspire easyStore Series appears in the navigation pane.
89
5 Browse or search for the item you want to play, then click the Play button.
90 4 Managing the server
To stream audio in iTunes:
1
2
Make sure iTunes Service is enabled. Refer to “Settings for iTunes
Server” on page 60 for more information.
3 Open the iTunes. The Acer Aspire easyStore Series appears under
Shared on the left of the iTunes window.
Audio files are streamed in iTunes and displayed under the Shared list.
4 Browse or seach for the item you want to play, then click the Play button.
91
Using the one-touch USB backup feature
The USB backup button on the front panel allows you to back up data from a USB storage device to the home server. Windows Home Server copies all files into the Publics shared folder first then classifies the files according to media type into their corresponding shared folders, namely Music, Videos, Photos. When Windows Home Server cannot determine file type, the file is automatically stored into the Others folder.
Important: Only the front USB port supports the backup feature.
To use one-touch USB backup to back up data from a USB storage device:
1 Plug the USB device into the front USB port.
92 4 Managing the server
2 Press the USB backup button. The USB backup indicator blinks blue.
3 All files on the USB storage device are copied into the Publics shared folder.
Note: During the copy process, Windows Home Server checks the file properties including time, size, and file name to verify whether a file of the same name or exactly the same file exists in the folder. If there is a conflicting file name, the data will be copied but will be assigned a serial number on the file name. If the file of exactly the same properties already exists in the Publics shared folder, the file will be filtered out of from the copy process.
4 Afterwards, Windows Home Server automatically copies and classifies the newly copied files according to their file type.
5 You can find files of different types in their corresponding shared folders (Music, Videos and Photos). Files other than music, videos and photos are accommodated in the Others folder.
6 When the back up process is completed, the USB backup indicator turns solid blue.
93
Set up Wake On LAN on the home server
The home server includes a Lights Out client software that allows the home computer to control the power state of the home server and wake up the home server from stand by. The Lights Out Client Service runs in the background. The utility does not have any user interface.
You don’t have to configure any address. Every time the client computer (that has the Windows Home Server Connector software installed) is started or comes out of standby, a WOL (Wake On LAN) magic packet is sent to the server.
To set up Wake On LAN on the home server:
1 Place the Aspire easyStore Series Software Installation Disc in the optical drive of the home computer. The installation wizard starts.
Or, double-click on the Client Installation.exe file to begin installation. The Welcome window appears.
2 Click Lights out.
Note: The Lights Out Client installer checks if the home computer has the Windows Home Server Connector. If no connector is found, the installation is aborted.
94
3 Select a language.
4 Click OK. The Welcome window appears.
4 Managing the server
5 Click Next.
6 Click Finish.
95
96 4 Managing the server
Set the home server uptime and down time
You can define times when the home server has to be up and running or define services where the server is never put into sleep mode during an active backup operation to reduce the risk of data loss.
Note: When creating an uptime you must enter a start and end time. The uptime end action can be created as a standalone action or in combination with an uptime.
To set the home server uptime and downtime:
1 Double-click the Windows Home Server icon in the system tray.
2 Log on to the Windows Home Server Console.
3 Click the Lights Out tab.
Home computers are indicated by color blocks in the diagram.
When you have more then 6 computers, the colors will be duplicated. The diagrams are created from left to right in the same order as the legend from top to bottom.
4 Click Calendar.
5 Select a day or days in the Calendar, then click Add.
6 Under Uptime start, set a start time to keep the server running.
7 Enable the “Wake up from suspension” option if you want to bring the home server out of standby on the defined time.
8 Under Uptime end, set an end time to disable the server.
9 Select from the following end actions:
• Do nothing - This is not useful for a standalone end action.
• Suspend - Puts your server into suspend mode.
• Shut down - Shuts down and powers off the server.
97
98 4 Managing the server
10 Enable the “Force end action” option if you want to immediately disable the server even when client monitoring detects active clients.
11 Select a day or days when to execute the command you selected in uptime start and uptime end parameter.
12 Click OK.
99
Monitor server health and performance
Your system includes a Hardware Health and Performance Monitor feature to help you keep a close eye on the system health of the home server. You can view graphical representations of a performance counter for CPU usage, memory usage, and storage usage and view the status of the home server’s fans, voltage, and temperature.
Note: To start the monitoring service successfully, it is required that you have administrator privileges on the home server.
To monitor the hardware health and performance data of the home server:
1 Double-click the Windows Home Server icon in the system tray.
2 Log on to the Windows Home Server Console.
3 Click the System Information tab.
4 Scroll down to the Hardware Performance and Health Monitor field.
100 4 Managing the server
Set up email alerts
You can set up an automatic email notification to provide alerts in the event of warnings or errors related to temperatures, fan speeds, or hard drive. To validate the email alert feature, you must also configure
SMTP setup.
To set up automatic email notifications:
1 Double-click the Windows Home Server icon in the system tray.
2 Log on to the Windows Home Server Console.
3 Click Settings.
4 In the navigation pane, select Hardware Health and Performance
Monitor.
5 In the E-Mail Alert Setting, type an email address to which email alerts will be sent. If there are more than one addresses, use a semicolon to separate different addresses.
6 Under Launch SMTP Setup, click Settings.
101
The Internet Accounts dialog box include the following options:
• Remove - Deletes an Internet Mail Account.
• Properties - Displays the Properties dialog box. This dialog box lets you configure the properties of established connections.
• Set as Default - Sets an Internet Mail Account as the primary account.
• Import - Imports your Internet Mail Account settings to an
Internet Account (.iaf) file format.
• Export - Exports an Internet Mail Account settings.
• Close - Exits the Internet Accounts dialog box.
7 Click Add to add an Internet connection.
102
8 Enter your name, then click Next.
4 Managing the server
9 Enter your email address, then click Next.
10 Enter the SMTP server information, then click Next.
Note: If you do not know your incoming and outgoing SMTP server name, contact your ISP (Internet service provider).
103
104 4 Managing the server
11 Enter the account name and password your ISP has given you, then click Next.
Note: Select the “Log On Using Secure Password Authentication
(SPA)” check box if your ISP requires you to use Secure Password
Authentication to access your mail account.
12 Click Finish.
13 On the Hardware Health and Performance Monitor page, click Test to send testing mails to the email addresses specified in order to verify whether notification can arrive smoothly.
14 Click OK.
Click Help in the Hardware Health and Performance Monitor page for more information.
105
Explore the Windows Home Server icon
The Windows Home Server icon notifies you about the health and status of the home server and your home computers. This includes notifications about user account password mismatches, software upgrades, and backup status. The icon also provides quick access to the
Windows Home Server Connector software via a right-click menu.
The color of the Windows Home Server icon represents the status of the home server:
Color Status
Indicates a healthy network
Indicates an issue that you must attend to soon
Indicates an issue that you must attend to immediately
Indicates that a backup is in progress
Indicates that your home computer cannot contact Windows
Home Server
For more information, right-click the Windows Home Server icon, click
Help.
106 4 Managing the server
5 Configuring the hard disk drive
107
The system supports up to four 3.5-inch hot-swappable SATA hard disk drives.
Warning: The first hard drive, located on the bottom of the HDD bay, is not hot-swappable.
Adding a hard disk drive
Caution: Hard drives are formatted before they are added to the server storage. Make sure that you back up any important files that are on the hard drive before you add it to server storage.
Formatting a hard drive deletes all files on the hard drive.
1 Install the new HDD to the home server.
(1) Open the door of the home server.
108 5 Configuring the hard disk drive
(2) Remove the HDD carrier by pressing the HDD carrier latch (1).
(3) Pull the lever (2) and slide the HDD carrier from the chassis (3).
(4) Insert the new drive into the right side of the carrier aligning the pins into the HDD’s mounting holes (1).
(5) Slightly bend the left side rail and insert the pins into the
HDD’s mounting holes (2).
109
(6) With the lever still extended, slide the carrier all the way into the drive bay (1). Do not push on the lever until it begins to close by itself.
(7) Use the lever to push the carrier until it docks into place, then close the lever (2).
(8) Close the door of the home server.
2 Add the hard drive to the server storage on Windows Home Server
Console.
(1) Double-click the Windows Home Server icon in the system tray.
(2) Log on to the Windows Home Server Console.
110
(3) Click the Server Storage tab.
5 Configuring the hard disk drive
(4) Select the newly installed hard drive (either internal or external), then click Add to run the Add a Hard Drive Wizard.
(5) Click Next.
(6) Select from the following options:
Add this hard drive to your server storage to increase the storage capacity of your home server. This option gives you more space to store home computer backups and more space for your shared folders.
111
Use this hard drive to back up files that are stored on your home server. This option allows you to back up all your home server shared folders.
(7) You can refer to the Windows Home Server Console Help for detailed instructions.
Important: When you add a hard drive to your server storage, you commit it to be part of your total server-storage space. Do not disconnect the hard drive to use it for other purposes. If you want to use the hard drive for other purposes, you should first select the hard drive and click Remove.
Caution: When you add a hard disk drive to the server storage, the hard disk drive will be formatted. Make sure to back up any important files that are on the hard disk drive before adding it to the server storage. Formatting a hard disk drive deletes all files on the hard disk drive.
112 5 Configuring the hard disk drive
Removing a hard disk drive
Caution: Always remove the hard drive from the Windows Home
Server Console before removing an HDD from the home server.
You will lose all files on a hard drive if you physically disconnect the HDD from your home server without running the Remove a
Hard Drive Wizard and you can no longer find the hard drive in order to connect it again.
1 Safely remove hard drive from the Windows Home Server Console.
(1) Double-click the Windows Home Server icon in the system tray.
(2) Log on to the Windows Home Server Console.
(3) Click the Server Storage tab.
(4) Select the hard drive you want to remove, then click Remove to run the Remove a Hard Drive Wizard.
(5) Click Next.
(6) Click Finish.
(7) The HDD indicator of the selected drive lights purple.
113
2 Remove the HDD from the home server.
Note: Before removing the HDD, make sure the HDD indicator on the front panel lights purple.
(1) Open the door of the home server.
(2) Press the HDD carrier latch (1).
(3) Pull the lever (2) and slide the HDD carrier from the chassis (3).
114 5 Configuring the hard disk drive
(4) Close the door of the home server.
Replacing a failed hard disk drive
1
Follow steps 1 and 2 of the “Removing a hard disk drive” section.
2 Remove the HDD from the carrier.
(1) Gently pry open the left side rail (1, 2), as shown.
(2) Remove the drive from the carrier (3).
3 Install the new HDD into the carrier.
(1) Insert the new drive into the right side of the carrier aligning the pins into the HDD’s mounting holes (1).
(2) Slightly bend the left side rail and insert the pins into the
HDD’s mounting holes (2).
115
4 Install the new HDD to the home server.
116 5 Configuring the hard disk drive
117
6 Troubleshooting
This chapter describes a list of possible situations that may arise during the use of your home server.
If you are unable to resolve problems on your own, contact your dealer or local Acer representative for assistance.
First steps checklist
• Is the AC power available at the wall outlet?
• Are the power supplies plugged in? Check the AC cable(s) on the back of the chassis and at the AC source.
• Are all cables correctly connected and secured?
• Are all peripheral devices correctly installed?
• Are all device drivers properly installed?
• Did you press the system power button on the front panel to turn the system on (power indicator should be lit)?
• Is the system power cord properly connected to the system and plugged into an outlet for 100-127 V or 200-240 V?
118 6 Troubleshooting
Recovering or restoring the home server
Aspire easyStore Series includes a Server Recovery DVD that allows you to recover your home server after a system failure (i.e., the operating system is corrupted, the main system hard drive failed). You can also use this disc to restore the home server to its factory default.
In Server Recovery, the home server’s system settings and user accounts will be lost. When you select the Factory Reset option, all data on the home server’s hard drives will be lost.
To recover the home server:
1 Place the Aspire easyStore Series Server Recovery DVD in the DVD drive of a computer connected to the network.
Or, double-click on the Acer ServerRecovery Utility.exe file to begin installation. The Server Recovery window appears.
119
2 Click Next.
3 Read the End-User License Agreement. If you agree with the terms of the agreement, then select the “I accept the terms of the user license agreement” option button.
4 Click Next.
5 Uninstall the Acer Aspire easyStore Series and Windows Home
Server Connector from your computer.
120 6 Troubleshooting
6 Recover the home server.
(1) Hold down the power button for 4 seconds to turn off the home server.
(2) Press the power button to turn it on.
(3) Turn the system around so that you have access to the back of the unit.
(4) Insert the end of an unfolded paperclip into the opening, and then press and hold the recovery/reset button with the paperclip end.
7 Click Next.
8 Select the “Server Recovery: Use this option to recover from a system failure. You will lose your system settings and user accounts. Data recovery will be attempted. (Recommended)” option button.
121
9 Click Next and follow all onscreen instructions until you finish recovery process.
To restore the home server to factory default setting:
1 Place the Server Recovery DVD in the DVD drive of a computer connected to the network.
Or, double-click on the Acer ServerRecovery Utility.exe file to begin installation. The Server Recovery window appears.
2 Click Next.
3 Read the End-User License Agreement. If you agree with the terms of the agreement, then select the “I accept the terms of the user license agreement” option button.
4 Click Next.
5 Uninstall the Acer Aspire easyStore Series and Windows Home
Server Connector from your computer.
122 6 Troubleshooting
6 Recover or reset the home server:
(1) Hold down the power button for 4 seconds to turn off the home server.
(2) Press the power button to turn it on.
(3) Turn the system around so that you have access to the back of the unit.
(4) Insert the end of an unfolded paperclip into the opening, and then press and hold the recovery/reset button with the paperclip end.
7 Click Next.
8 Select the “Factory Reset: Use this option to restore factory defaults. All your data and settings will be erased” option button.
9 Click Next and follow all onscreen instructions until you finish restore process.
123
Restoring a home computer
You can easily restore any of your home computers to a previous point in time with a backup stored on your home server. You can do this by using the PC Recovery Disc. This CD can be used to restore all of the files on your home computer from a backup, including the Windows operating system and applications.
To restore a home computer:
Important: You need the Windows Home Server administrator password to restore a home computer.
1 Place the Aspire easyStore Series PC Recovery Disc in the CD drive of the computer that you want to restore.
2 Restart the computer and boot from CD.
3 Follow the instructions in the Restore Computer Wizard to restore the hard drives on your home computer.
Note: Your home computer must be connected to the home network with an Ethernet network cable before you begin the restore. Wireless connection is not supported.
124 6 Troubleshooting
When you boot the home computer to the PC Recovery Disc, it lists the NIC (network interface card) and storage devices it has found and it provides an option to load drivers, as shown in the screenshot below. It can also search USB flash or USB floppy drives for driver files and load any found Windows drivers.
If the drivers did not load or the NIC driver cannot be found during computer recovery, you can perform the options listed below to install the drivers, otherwise the home computer will not be able to connect to the home server to get your backup.
• You can use a Vista-compatible NIC driver, which is fully compatible with computers running Windows Vista or
Windows XP. Download and install the Vista-compatible NIC driver from a USB flash or USB floppy drive.
• On the Detect Hardware dialog box, click “Where can I find drivers for my hardware?” to bring up an online help file for detailed instructions on how to find and load drivers.
• Go to http://www.microsoft.com/windows/products/ winfamily/windowshomeserver/support.mspx for more information.
4 Every time Windows Home Server backs up a home computer, it saves the drivers for the home computer in the backup that is stored on the home server. When you use the PC Recovery Disc, you will be prompted if the home computer requires drivers for any of your home computers, you can open a backup for that home computer and copy the drivers to a USB flash or USB floppy drive.
125
Restoring files from a backup
You can browse and restore lost files from any client computer on your home network that has been backed up with Windows Home Server.
To restore files and folders from a backup:
1 Open the Windows Home Server Console.
2 Click the Computers & Backup tab.
3 Select a home computer, then click View Backups.
4 Select a backup, then click Open.
5 Select a volume to open, then click Open.
Note: The Opening Backup status window appears while the backup opens. If you are prompted to restart your computer after the virtual volume driver is installed, ignore this message, you do not need to restart your computer.
6 Drag the backup files and folders that you want to restore to a folder on your home computer.
7 Close the window when you are done copying the files and folders that you want to restore.
126 6 Troubleshooting
Update your home server with
Aspire easyStore Series Software
Update
The Aspire easyStore Series Software Update is a tool which allows you to easily update the home server BIOS, drivers, and add-in software.
To install the Aspire easyStore Series Software Update utility:
1 Place the Aspire easyStore Series Software Installation Disc in the optical drive of the home computer. The installation wizard starts.
Or, double-click on the Client Installation.exe file to begin installation. The Welcome window appears.
2 Click Software Update. The Welcome window displays.
127
3 Click Next.
128
4 Select a destination directory, then click Next.
6 Troubleshooting
5 Select a program folder or enter a new folder, then click Next.
129
6 Select the options you want installed on your hard drive, then click
Next.
7 Click Install.
8 Click Finish.
130 6 Troubleshooting
To update your home server with Software Update utility:
1 Make sure the Aspire easyStore Series Software Update utility is installed on the computer. Refer to previous section for detailed instruction.
2 On your computer, click Start > Programs > Aspire easyStore Series
Software Update > Software Update.
3 In the Home Server field, select the home server you want to update. You can click Rescan to refresh the list.
4 In the Software\BIOS field, click Browse to specify the software/
BIOS package which will be updated to the home server.
5 Enter your name and password.
6 Select the “Remember Account” check box if you want the account you entered to be shown the next time you perform software update.
7 Click Install and follow onscreen instructions to complete updates.
131
Specific problems and corrective actions
The following contains specific problems that may arise during the use of your server. Possible solutions are listed for each problem.
Power indicator does not light.
• Make sure the power button on the front panel is turned on.
• Make sure the power cord is connected correctly.
• Make sure that the wall outlet has power. Test it by plugging another device.
HDD status indicator does not light.
Make sure the hard drive is compatible.
If the drives are pre-installed, contact technical support.
Home server cannot connect to a network and the network indicator on the front panel does not light.
• Make sure the network cable is securely attached to the correct connector at the system rear panel.
• Try a different network cable.
• Make sure the broadband router has power.
Home computer cannot connect to the home server
• Make sure the power button on the front panel is turned on.
• Make sure the network indicator on the front panel lights blue.
• Make sure the broadband router has power.
• Make sure a firewall is not blocking the connection. Refer to the
Windows Home Server Console Help for more information.
• Shutdown and restart your home server.
• Reset the home server.
To soft reset the home server:
(1) Launch Windows Home Server Console.
(2) Click Options.
132 6 Troubleshooting
(3) Select “Reset the Windows Home Server Console” from the drop-down menu.
(4) Click OK.
Backup service is not running
If you see the “If backup service is not running, please restart the console.”error message, try resetting the home server.
1 Launch Windows Home Server Console.
2 Click Options.
3 Select “Reset the Windows Home Server Console” from the dropdown menu.
4 Click OK.
How do I save the Windows Home Server backup database
For detailed instructions on how to copy the backup database from your Windows Home Server, go to http://www.microsoft.com/ windows/products/winfamily/windowshomeserver/support.mspx
Web browser cannot display the Aspire easyStore Series Remote
Access page when accessing through URL
• Make sure the Web Site Connectivity in Settings is turned on.
• Make sure JavaScript is enabled on your browser.
To enable JavaScript in Internet Explorer 7:
(1) From the Internet Explorer menu, go to Tools, then select
Internet Options.
(2) Choose the Security tab, then click Custom Level.
(3) Scroll down to Active Scripting, then select Enable.
(4) Click OK.
133
Can’t connect to some computers on the Aspire easyStore Series
Remote Access page
Make sure the home computer is configured to allows remote desktop connection.
To configure computers that are running Windows XP:
1 Log on to the computer with a user account that has administrator privileges.
2 Click Start, right-click My Computer, then click Properties.
3 On the System Properties page, click the Remote tab.
4 Make sure that the “Allow users to connect remotely to this computer” check box is selected.
5 Click Select Remote Users. User accounts with administrator privileges are automatically allowed to connect. If you want to allow additional user accounts to remotely access this computer, click Add to enter those user accounts.
6 If you use Windows Firewall, open Control Panel, and then doubleclick Windows Firewall. Verify that Windows Firewall is on. Click the Exceptions tab, and then verify that Remote Desktop is selected.
7 Restart your computer.
To configure computers that are running Windows Vista:
1 Log on to the computer with a user account that has administrator privileges.
2 Click Start, right-click Computer, then click Properties.
3 Click Remote settings, click Continue.
4 Make sure that the “Allow connections from computers running any version of Remote Desktop (less secure)” check box is selected.
Important: If you select Allow connections only from computers running Remote Desktop with Network Level Authentication
(more secure), you cannot connect to this computer via Windows
Home Server Remote Access, and the connection status for this computer is Disabled.
134 6 Troubleshooting
5 Click Select Users. User accounts with administrator privileges are automatically allowed to connect. If you want to allow additional user accounts to remotely access this computer, click Add to enter those user accounts.
6 If you use Windows Firewall, open Control Panel, then click
Security. Click Windows Firewall. Verify that Windows Firewall is on. Click Change Settings, and then click Continue. Click the
Exceptions tab, then verify that Remote Desktop is selected.
7 Restart your computer.
I forgot the Windows Home Server password
If you don’t remember the password, you must reset the home server.
Refer to “Recovering or restoring the home server” on page 118 for
more information.
Shkarko
Lidhja publike u përditësua
Lidhja publike për bisedën tuaj është përditësuar. You may view and manage your chat links after registration here.
Lidhja publike e dokumentit
Reklamë