Biostar U8668-D Owner's Manual

U 8 6 6 8 D

FCC Information and Copyright

This equipment has been tested and found to c omply with the limits of a

Class B digital device, pursuant to Part 15 of the FCC Rules . T hese limits are designed to provide reasonable protection agains t harmful interference in a residential installation. This equipment generates , uses and can radiate radio frequency energy and, if not ins talled and used in accordance with the instructions, may c ause harmful interference to radio communications . There is no guarantee that interference will not occur in a partic ular installation.

The vendor makes no representations or warranties with respec t to the contents here of and specially disclaims any implied warranties of merchantability or fitness for any purpose. Further the vendor reserves the right to revise this publication and to make changes to the c ontents here of without obligation to notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without firs t obtaining the vendor’s approval in writing.

The c ontent of this user’s manual is subject to be changed without notice and we will not be responsible for any mistakes found in this us er’s manual. All the brand and product names are trademarks of their respective c ompanies . i

U 8 6 6 8 D

ENGLIS H................................................................................................... 3

U8668-D Features................................................................................. 3

Package contents................................................................................... 4

Layout of U8668-D (only for version 1.x and 6.x) ......................... 5

Layout of U8668-D (only for version 3.3)....................................... 6

Layout of U8668-D (only for version 4.0)....................................... 7

Layout of U8668-D (only for version 5.x)....................................... 8

Layout of U8668-D (only for version 5.A) ...................................... 9

Layout of U8668-D (only for version 5.B & above) ..................... 10

Layout of U8668-D (only for version 7.0~7.3).............................. 11

Layout of U8668-D (only for version 7.5~7.7).............................. 12

Layout of U8668-D (only for version 7.8 & above)...................... 13

CPU Installation ................................................................................. 14

DDR DIMM Mo dules: DDR1-2 ........................................................ 14

Jumpers, Headers, Connectors & Slots............................................ 15

TROUB LE S HOOTING..................................................................... 21

ES PAÑOL ................................................................................................ 22

Características del U8668-D.............................................................. 22

Contenido del Paquete ....................................................................... 23

SOLUCIÓN DE PROBLEMAS ......................................................... 24

FRANÇAIS .............................................................................................. 25

Caractéristiques de U8668-D............................................................. 25

Contenu de l'Emballage..................................................................... 26

DÉPANNAGE ...................................................................................... 27

Chapter 3: WarpS peeder™ ................................................................... 28 ii

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

English

U8668-D Features

CPU

Provides

Support the Intel

®

Pentium

®

Pentium

®

4 Northwood CPU up to 3.06GHz.

®

4 478 Prescott CPU (f or v ersion 5.A/5.B and v ersion 7.5 & abov e).

- 533FSB with 1024KB L2 Cache

- Celeron D (533 FSB with 256KB L2 Cache)

Running at 400/533MHz Front Side Bus.

Supports Hy per-Threading Technology.

Version 7.8 and above do not support Willamette CPU.

Standard Intel CPU f an is suggested.

Chipset

North Bridge: P4M266A

South Bridge: VT8235

Main Memory

Supports up to 2 DDR devices.

Supports 200/266MHz DDR devices.

The largest memory capacity is 2GB.

Super I/O

Chipset: ITE IT8705.

Slots

Three 32-bit PCI bus master slots (for version 3.x, 4.x, 5.x, 5.A, 5.B and 7.x).

Two 32-bit PCI bus master slots (only f or v ersion 1.x and 6.x).

One CNR slot (f or v ersion 3.x, 4.x, 5.x, 5.A, 5.B and 7.x only ).

One AMR slot (for version 1.x and 6.x).

One AGP slot.

On Board IDE

Supports four IDE disk drives.

Supports PIO Mode 4, Master Mode and Ultra DMA 33/66/100/133 Bus

Master Mode.

LAN (only support for version 3.3)

RTL8201BL.

Half/Full duplex operation.

LAN

VIA VT6103/6103L (Only Version 7.8 and abov e support VIA VT6103L chipset.)

Dual Speed: 10/100Mbps, Full/Half Duplex.

Auto Negotiation: 10/100 Mbps, Full/Half Duplex.

3

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

On Board AC’97 Sound Codec

Chip: VIA1612A (for version 3.x, 6.x, and 7.0-7.6)

Compliant with AC’97 specification.

Supports 2 channel speakers.

On Board AC’97 Sound Codec (optional)

Chip: CMI9739A (for version 1.x, 4.x, 5.x, 5.A, 5.B, 7.7, 7.8 & abov e)

Compliant with AC’97 specification.

Supports 6 channel speakers.

On Board Peripherals

Supports 360K, 720K, 1.2MB, 1.44MB and 2.88MB f loppy disk driv ers.

Supports 1 serial port.

Supports 1 VGA port.

Supports 1 multi-mode parallel port. (SPP/EPP/ECP mode)

Supports PS/2 mouse and PS/2 key board.

Supports 6 USB2.0 ports. (Either rear x 4 + f ront x 2 or rear x 2 + front x 4)

BIOS

AWARD legal Bios.

Supports USB Function.

Operating System

Offers the highest performance for MS-DOS, Windows 2000, Windows Me,

Windows XP, SCO UNIX etc.

Dimensions

Micro ATX Form Factor: 19.5cm X 22.8cm (W X L) (only f or v ersion 1.x and

6.x)

Micro ATX Form Factor: 19.5cm x 24.4cm (W x L) (only f or v ersion 3.x, 4.x,

5.x, 5.A, 5.B and 7.x)

Package contents

Fully Setup Driv er CD

USB Cable (optional)

Rear I/O Panel (optional)

4

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

Layout of U8668-D (only for version 1.x and 6.x)

JK BMS1

K/ B

&

Mouse

1

JC FA N 1

JATX PWR 1

S ocket 478

C PU

JCO M1

JA TXPW R2

JPR NT1

JVGA 1

JU SBLA N1

USB

&

L AN

JA U DIO 1

2

JAU DIO

10 9

1

Super

I/O

BIOS

LAN

C ode c

P4M 266A

2 JGA ME1 1 6

1 1 5

1

JW O L1

JCD IN 1

1

Back Panel Connector

JSPDIFO 1

A MR 1

1

FD D1

PCI2

JKBMS1

PS/2

Mouse

JPRNT1

Parallel

PCI1

A G P1

2

1

JU SB2

10

9

JUSBLAN2

LAN

ID E1 ID E2

JC MO S1

BAT1

1

1

JSFAN 1

2

1

JPA NEL1 1

JCI1

2 4

2 3

Line In

Speaker Out

Mic In

PS/2

Keyboard

USB

JUSB1

COM1

JCOM1

V GA

JVGA1

USB

JAUDIO

5

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

Layout of U8668-D (only for version 3.3)

JKBMS1

K/B

&

Mo use

1

JKBS 1

1

JCFA N1

JATX PWR 1

Soc ke t 478

CP U

JCO M1

JP RNT1

JATX PW R2

1

JUS BV2

JVGA1

JUSBLAN1

U SB

&

LA N

JAU DI O1

2

JAU DIO

10 9

1

Super

I/O

BIOS

LAN

C od ec

2

JGAME1

1 6

1 1 5

1

JWO L1

JCDI N1

1

JS P DI FO 1

CN R1

1

P4M 266A

F DD1

P CI 1

AGP 1

2

1

JUS B2

1 0

9

P CI2

P CI3

1 JUS BV3

I DE1 I DE2

JC MOS 1

1

BA T1

1

JS FA N1

JP AN EL1

2

1

1

JCI 1

24

23

Back Panel Connector

JKBMS1

PS/ 2

Mouse

JPRNT1

Parallel

JUSBLAN2

LAN

Line In

Speaker Out

Mic In

PS /2

Keyboard

USB

JUSB1

COM1

JCOM1

VGA

JVGA1

USB

JAUDIO

6

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

Layout of U8668-D (only for version 4.0)

JKBMS1

K/B

&

Mo use

1

JCFA N1

JATX PWR 1

So c ke t 4 7 8

CP U

JCO M1

JP RNT1 JATX PW R2

I DE1 I DE2

JVGA1

JUSBLAN1

U SB

&

LA N

JAU DI O1

2

JAU DIO

10 9

1

Super

I/O

BIOS

LAN

C od ec

2 JGAME1 1 6

1 1 5

1

JWO L1

JCDI N1

1

JS P DI FO 1

CN R1

1

P4M266A

F DD1

AGP 1

P CI 1

2

1

JUS B2

1 0

9

P CI2

P CI3

Back Panel Connector

JKBMS1

PS/2

Mouse

JPRNT1

Parallel

JUSBLAN2

LAN

JC MOS 1

1

BAT1

1

JS FA N1

JP AN EL1

2

1

1

JCI 1

24

23

Line In

Speaker Out

Mic In

PS/2

Keyboard

USB

JUSB1

COM1

JCOM1

VGA

JVGA1

USB

JAUDIO

7

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

Layout of U8668-D (only for version 5.x)

JKBMS1

K eybo ard

&

Mo use

1

JKBS 1

1

JCFA N1

JATX PWR 1

So c ke t 4 7 8

CP U

JCO M1

JP RNT1 JATX PW R2

1

JVGA1

JUSBLAN1

U SB

&

LA N

JU SBV 2

JAU DI O1

2

JAU DIO

10 9

1

Super

I/O

BIOS

LAN

C od ec

2 JGAME1 1 6

1 1 5

1

JWO L1

JCDI N1

1

JS P DI FO 1

CN R1

1

P4M266A

F DD1

AGP 1

P CI 1

2

1

JUS B2

1 0

9

P CI2

P CI3

1 JUS BV3

I DE1 I DE2

JC MOS 1

1

BAT1

1

JS FA N1

JP AN EL1

2

1

1

JCI 1

24

23

Back Panel Connector

J KBMS1

PS/2

Mouse

(Optional)

JPRNT1

P arallel

JUSBLAN2

LAN

Li ne In

Speaker Out

Mic In

PS/2

Keyboard

USB

JUSB1

COM1

J COM1

VGA

JVGA1

USB

JAUDIO

8

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

Layout of U8668-D (only for version 5.A)

JK B M S1

K eyboard

&

M ouse

1

JK B S 1

1

JC F A N 1

JA T X PW R 1

Socket 478

C P U

JC O M 1

JP R N T 1 JA T X P W R 2

ID E 1 ID E 2

JV G A 1

JU SB L A N 1

USB

&

LAN

1

JU SB V 2

JA U D IO 2

15

16

JA U D IO 1

1

2

L A N

Codec

1

JW O L 1 JC D IN 1

1 JS PD IF O 1

S uper

I/O

1

P4M 266A

B IO S

Back Panel Connector

C N R 1

JKBMS1

PS/2

Mouse

(Optional)

JPRNT1

Parallel

A G P 1

P C I1

2

1

JU S B 2

1 0

9

JC M O S1

1

B A T 1

P C I2

2

1

JU SB 3

1 0

9

P C I3

F D D 1

1 JU S B V 3

VT8235 1

JSATA 1

1

JSATA2

1

JSF A N 1

2

1

JP A N E L 1

JC I1

1

24

23

JUSBLAN2

LAN

Line In

Speaker Out

Mic In

PS/2

Keyboard

USB

JUSB1

COM1

JCOM1

VGA

JVGA1

USB

JAUDIO

9

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

Layout of U8668-D (only for version 5.B & above)

JK B M S 1

Keyboard

&

M ouse

1

JK B S1

1

JC FA N 1

JA T X P W R 1

Socket 478

C P U

JC O M 1

JPR N T 1 JA T X PW R 2

ID E 1 ID E 2

JV G A 1

1

JU SB V 2

JU S BL A N 1

P4M 266A

JA U D IO 2

10 9

2 1

JA U D IO 1

A G P 1

JC M O S 1

LA N

VT8235

B A T 1

1

C od e c

1

JW O L 1 JC D IN 1

1

S uper

I/O

B IO S

JSP D IFO 1

C N R 1

Back Panel Connector

PC I1

2

1

JU SB 2

1 0

9

1

FD D 1

PC I2

PC I3

2

1

JU S B 3

10

9

1

JU S B V 3

1

JS ATA1

( Op ti on al )

1

JS ATA 2

( Op ti on al)

1

JSF A N 1

2

1

JPA N E L 1 1

JC I1

24

23

JKBMS1

PS/2

Mouse

(Optional)

JPRNT1

Parallel

JUSBLAN2

LAN

Line In

Speaker Out

Mic In

PS/2

Keyboard

USB

JUSB1

COM1

JCOM1

VGA

JVGA1

USB

JAUDIO

10

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

Layout of U8668-D (only for version 7.0~7.3)

J KBM S1

K/B

&

Mouse

US B

&

LAN

JCOM1

So ck et 4 78

CPU

1

JCF AN1

JATXPWR1

JATXPWR2

JP RNT1

JVGA1

Sup er

I/O

JA UD _GA ME

BI OS

JA UDIO1

10 9

2 1

Co dec

LAN

2 JGAME1 16

1 15

1

JWOL1

JCDI N1

1

JSP DIF O1

CNR1

1

P4M2 66 A

FDD1

PCI1

PCI2

PCI3

AGP 1

2

1

JUS B4

10

9

2

1

JUS B2

10

9

1

JSF AN1

JPA NEL1

2

1

Back Panel Connector

JKBMS1

PS/2

Mouse

JUSBLAN1

LAN(Optional)

P S/2

Ke yboard

USB COM1

JCOM1

JPRNT1

Parallel

VGA1

JVGA1

ID E1 ID E2

JCMOS1

1

B AT1

1

JCI1

24

23

JGAME1

Game Port

Speaker

Out

Line In Mic

In

11

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

Layout of U8668-D (only for version 7.5~7.7)

JKBMS1

Key board

&

Mouse

1

JC FAN1

JA TX PWR 1

Soc ket 478

CPU

JUSBLAN1

JCO M1

JPRNT1 JATXPWR2

IDE1 ID E2

JVGA1

P4M266A

C od ec

1

JWO L1

JCDIN1

1

Supe r

I/O

BI OS

JAU D_GA ME

10 9

JAUD IO 1

2 1

LAN

JSPDIFO1

CNR1

1

AGP1

JCMO S1

PCI3

2

1

10

9

JU SB3

1

FDD 1

PCI1

PCI2

2

1

JUSB4

1 0

9 VT8235

2

1

JUSB2

10

9

BAT 1

1

JS ATA 1

1

JS ATA 2

1

JSFAN 1

JPAN EL1

2

1

JCI1

1

2 4

2 3

Back Panel Connector

JKBMS1

PS/2

Mouse

JUSBLAN1

LAN(Optional)

JPRNT1

Pa ral le l

JGAME1

Game Port

PS/2

Keyboard

USB COM1

JCOM1

VGA1

JVGA1

Speaker

Out

Line In Mic

In

12

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

Layout of U8668-D (only for version 7.8 & above)

JKBMS1

Keyb oard

&

Mouse

So c ke t 47 8

CPU

1

JCF AN1

JA TXP WR1

JUSBLAN1

JCOM1

JP RNT1 JATXP WR2

ID E1 I DE2

JVGA1

P4M 266A

Co de c

1

JWOL1 JCDIN1

1

Super

I /O

BI OS

JA UD_G AME

10 9

2 1

JAU DIO 1

LAN

JS PDI F O1

CNR1

1

AGP 1

JCMOS1

PCI 3

2

1

1 0

9

JUS B3

1

F DD1

P CI 1

PCI 2

1

2

JUSB4

10

9

VT8235

2

1

JU SB2

1 0

9

BAT1

1

JSATA1

1

JS ATA 2

1

JS FAN 1

2

1

JP ANEL1

JCI1

1

2 4

2 3

Back Panel Connector

JKBMS1

PS/2

Mouse

JUSBLAN1

LAN(Optional)

JPRNT1

Pa ral le l

JGAME1

Game Port

PS/2

Keyboard

USB COM1

JCOM1

VGA1

JVGA1

Speaker

Out

Line In Mic

In

13

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

CPU Installation

CPU Fan

CPU

1. Pull the lever sideway s away from the socket then raise the lever up to a

90-degree angle.

2. Locate Pin A in the socket and look for the white dot or cut edge in the CPU.

Match Pin A with the white dot/cut edge then insert the CPU.

3. Press the lever down. Then Put the f an on the CPU and buckle it and put the f an’s power port into the JCFAN1, then to complete the installation.

CPU/ S ystem Fan Headers: JCFAN1/ (JS FAN1 => optional)

1 Ground

12 V

Sense

1 Ground

12V

Sense

J CFAN1 JSFAN1

DDR DIMM Modules: DDR1-2

DRAM Access Time: 2.5V Unbuffered/ Registered DDR 200 MHz (PC1600)/

DDR 266 MHz (PC2100) Ty pe required.

DRAM Ty pe: 64MB/ 128MB/ 256MB/ 512MB/ 1GB DIMM Module.(184 pin)

DIMM Socket

Location

DDR 1

DDR 2

DDR Module

64MB/128MB/256MB/512MB/1GB *1

64MB/128MB/256MB/512MB/1GB *1

Total Memory Size

(MB)

Max is

2GB z The list shown abov e f or DRAM configuration is only f or reference.

14

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

How to install DDR DIMM Module

1. The DDR DIMM socket has a “ Plastic Saf ety

Tab”, and the DDR DIMM memory module has an

Asy mmetrical notch”, so the DDR DIMM memory module can only f it into the slot in one direction.

2. Push the tabs out. Insert the DDR DIMM memory modules into the socket at a 90-degree angle, and then push down vertically so that it will f it into the place.

3. The Mounting Holes and plastic tabs should fit over the edge and hold the DDR DIMM memory modules in place.

Jumpers, Headers, Connectors & Slots

Hard Disk Connectors: IDE1/ IDE2

The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO

Mode 0~4, Bus Master, and Ultra DMA 33/ 66/ 100/ 133 functionality. It has two

HDD connectors IDE1 (primary) and IDE2 (secondary).

The IDE connectors can connect a master and a slave driv e, so you can connect up to f our hard disk driv es. The f irst hard drive should alway s be connected to

IDE1.

Floppy Disk Connector: FDD1

The motherboard provides a standard f loppy disk connector that supports 360K,

720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the prov ided f loppy drive ribbon cables.

Audio Modem Riser Slot: AMR1 (only for version 1.x and 6.x)

(Only support slav e card)

The AMR specif ication is an open Industry Standard Architecture and that defines a hardware scalable riser card interface, which supports audio and modem only.

Peripheral Component Interconnect Slots: PCI1-3 (only for version 3.x, 4.x, 5x, 5.A, 5.B, 7.x)

This motherboard is equipped with 3 standard PCI slots. PCI stands f or Peripheral

Component Interconnect, and it is a bus standard for expansion cards. This PCI slot is designated as 32 bits.

Peripheral Component Interconnect Slots: PCI1-2 (only for version 1.x and 6.x)

This motherboard is equipped with 2 standard PCI slots. PCI stands f or Peripheral

Component Interconnect, and it is a bus standard for expansion cards. This PCI slot is designated as 32 bits.

15

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

Accelerated Graphics Port S lot: AGP1

Y our monitor will attach directly to that v ideo card. This motherboard supports video cards for PCI slots, but it is also equipped with an Accelerated Graphics Port

(AGP). An AGP card will take adv antage of AGP technology f or improved v ideo efficiency and performance, especially with 3D graphics.

Communication Network Riser S lot: CNR1 (optional)

The CNR specification is an open Industry Standard Architecture, and it defines a hardware scalable riser card interf ace, which supports audio and modem only.

Front USB Header: JUSB2/ (JUS B3=>only for version 5.A & 5.B,

7.2; JUS B4=>only for version 7.x)

2

1

JUSB2/4

Pin Assignment Pin Assignment

1

3

+5V

Data (-)

2

4

+5V

Data (-)

5

7

9

Data (+)

Ground

Key

6

8

10

Data (+)

Ground

NA

Power Connectors: JATXPWR1/ J ATXPWR2

JATXPWR2

( ATX 12V Power Connector)

JA TX PWR1

( AT X Ma in P ow er Connec tor )

JATXPWR1

PIN Assignment PIN Assignment

1 +3 .3V 11 +3 .3V

2 +3 .3V 12 -12V

3 G round 13 G round

4 +5V 14

5 G round 15 G round

7 G round 17 G round

8 PW_OK 18 -5V

9 +5V_Standby 19 +5V

10 +12V 20 +5V

16

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

JATXPWR2

PIN Assignment

3 G round

Front Panel Connector: JPANEL1

SLP

PWR_LED

(+ ) ( +) (- )

ON/OFF IR

2

1

SPK

(+ ) ( -)

HLED

RST IR

SPK ==> Speaker Conn.

HLED ==> Ha rd Driver LED

RST ==> Reset Button

IR ==> Infrared Conn.

SLP ==> Sleep Button

PWR_LE D ==> Power LED

ON/ OFF ==> Power-on Button

Clear CMOS Jumper: JCMOS

24

23

JCMOS Assignment

Pin 1-2 on Normal

Operation

1

(default)

Pin 2-3 on

Clear CMOS

Data

1

※ Clear CMOS Procedures:

1 . Remove AC power line.

2 . Set JCMO S1 (2-3 ) closed.

3 . Wait for five seconds .

4 . Set JCMO S1 (1-2 ) closed.

5 . Power on AC.

6 . Reset your desired pass word or c lear the CMO S data.

Audio S ubsystem: JAUDIO1/ JCDIN1

1 0 9

2

1

2 1

JA UD IO1

(Fro n t Au dio Head er)

JC DIN 1

( CD-RO M A u dio- In H ead er)

17

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

2 2

1

10

9

JF_ AU DIO 1

Pin

1

3

5

7

9

Ass ignment

Mic In

Mic Power

RT Line Out

Reserved

LFT Line Out

Pin

2

4

6

8

10

Assign ment

Ground

Audio Po wer

RT Line Out

Key

LFT Line Out

Fro nt Pan el Au dio C onn ecto r/ Ju mper B lock

Jump er Se tting C on fig ur ation

5

7

9

1

3

1 0

Pin 5 and 6

Pin 9 and 1 0

Audio lin e o ut sig nals are rou ted to

th e b ack pan el au dio lin e o ut conn ecto r.

5

7

9

1

3

1 0

No jum per s

installed

Aud io line ou t an d m ic in sign als ar e av ailabl e fo r fro nt pan el au dio co nn ector s.

Audio S ubsystem: JCDIN1/ JAUD IO1 (only support for version

5.1 & 5.A)

15

1 6

1

2

JAUDIO1

(Front Audi o Header)

1

J CDIN1

(C D-ROM Audio-In Header)

15

1 6

Pin

1

3

5

7

9

11

13

15

Assignment

Mi c In

Mic Power

Right Line Out

Reserved

Left Line Out

Surrender Right

Center

Ground

2

1

2

Pin

2

4

6

8

10

12

14

16

JAUDIO1

Assignment

Ground

Audio Power

Right Line Out

NC

Left Line Out

Surrender Left

Subwoof

KEY

18

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

Game Header: JGAME1 (o ptional)

2

1

16

15

JGAME1

Pin Assignment Pin Assignment

1 +5V 2 +5V

11

13

15

7

9

3

5

GP6

GP2

MIDI-OUTR

GP3

GP7

MIDI-INR

NC

4

6

8

10

12

14

16

GP4

GP0

Ground

Ground

GP1

GP5

+5V

Digital Audio Connector: JS PDIF_OUT1 (optional)

S PDIF_Out

GND 5V

1

JSPDIF_ OUT

Wake On LAN Header: JWO L1 (optional)

Gr ound

5V Wake up

1

JWOL1

Case Open Connector: JCI1 (optional)

JCI1

1

No jumper installed

1

Pin 1-2 on

Assignment

Normal

Operation

(default)

Case Open

19

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

Power S ource Selection for KB/MS and US B0/1: JKBS 1 (only for version 3.3 and 5.x, 5.A, 5.B)

JKBS1

1

Pin 1-2 on

1

Pin 2-3 on

Assignment

5V

5V_SB

Power S ource Selection for USB: JUSBV2/ JUS BV3 (only for version 3.3 and 5.x, 5.A, 5.B)

JUSBV2/3

1

Pin 1-2 on

Assignment

5V

1

Pin 2-3 on

5V Standby

20

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

Trouble Shooting

PROBABLE SOLUTION

No power to the system at all Power light * Make sure power cable is securely don’t illuminate, f an inside power supply does not turn on. Indicator light on plugged in

* Replace cable key board does not turn on

* Contact technical support

System inoperativ e. Keyboard lights are on, power indicator lights are lit, hard driv e is spinning.

* Using even pressure on both ends of the DIMM, press down firmly until the module snaps into place.

System does not boot from hard disk driv e, can be booted f rom optical driv e.

* Check cable running from disk to disk controller board. Make sure both ends are securely plugged in; check the driv e type in the standard CMOS setup.

* Backing up the hard drive is extremely important. All hard disks are capable of breaking down at any time.

System only boots f rom optical driv e.

Hard disk can be read and applications can be used but booting from hard disk is impossible.

* Back up data and applications files.

Ref ormat the hard driv e. Re-install applications and data using backup disks.

Screen message says “Invalid

Conf iguration” or “CMOS Failure.”

* Review system’s equipment . Make sure correct information is in setup.

Cannot boot system after installing second hard driv e.

* Set master/slave jumpers correctly.

* Run SETUP program and select correct driv e types. Call drive manuf acturers f or compatibility with other drives.

21

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

Español

Características del U8668-D

CPU

Socket-478.

Soporta procesador Intel Pentium 4 de hasta 3.06GHz.

Soporta Intel Pentium 4 478 Prescott CPU. (solamente para v ersión 5.A/5.B en adelante; 7.5 en adelante)

Corre a 400/ 533MHz Front Side Bus.

Soporta Tecnología Hyper-Threading.

La versión 7.8 no admite el procesador Willamette.

Se recomienda el ventilador de procesador Intel estándar.

Chipset

North Bridge: P4M266A

South Bridge: VT8235

Memoria Principal

Soporta hasta 2 dispositivos DDR.

Soporta dispositivos DDR de 200/ 266MHz.

Capacidad máxima de memoria 2GB.

Super I/O

Chipset: ITE IT8705.

Ranuras

Dos ranuras de 32-bit PCI bus master. (solamente para versión 1.x y 6.x)

Tres ranuras de 32-bit PCI bus master. (solamente para versión 3.x, 4.x, 5.x,

5.A, 5.B y 7.x)

Una ranura CNR. (solamente para versión 3.x, 4.x, 5.x, 5.A, 5.B y 7.x)

Una ranura AMR. (solamente para v ersión 1.x y 6.x)

Una ranura AGP.

IDE Onboard

Soporta cuarto discos IDE.

Soporta Modos PIO 4, Modo Master y Modo Ultra DMA 33/66/100/133 Bus

Master.

LAN (solamente soporta para versión de placa madre 3.3)

10/100Mbps.

Full/Half Duplex.

LAN

VIA VT6103/6103L (Sólo la versión 7.8 y posteriores admiten el conjunto de chips VT6103L).

Dual Speed: 10/100Mbps.

22

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

Auto Negociación: 10/100 Mbps, Full/Half Duplex.

AC’97 Sound Codec Onboard

Chipset: VIA1612A (solamente para v ersión 3.x, 6.x, y 7.0-7.6)

Constituy e con la especificación del AC’97.

AC’97 Sound Codec Onboard (opcional)

Chipset: CMI9739A (solamente para v ersión 1.x, 4.x, 5.x, 5.A , 5.B, 7.7, 7.8 y posteriores )

Constituy e con la especificación del AC’97.

Periféricos Onboard

Soporta disquette de 360K, 720K, 1.2MB, 1.44MB y 2.88MB.

Soporta 1 puerto serie.

Soporta 1 puerto VGA.

Soporta 1 puerto paralelo multi-mode. (modo SPP/EPP/ECP)

Soporta ratón PS/2 y teclado PS/2.

Soporta 6 puertos USB2.0 (2 x traseros + 4 x f rontales/ 4 x traseros + 2 x frontales.

BIOS

AWARD legal Bios.

Soporta f unción USB.

Sistemas Operativos

Ofrece el más alto funcionamiento para MS-DOS, Windows 2000, Windows

Me, Windows XP, SCO UNIX etc.

Dimensiones

Factor de Forma Micro ATX: 19.5cm X 22.8cm (W X L) (solamente para v ersión 1.x y 6.x)

Factor de Forma Micro ATX: 19.5cm x 24.4cm (W X L) (solamente para v ersión 3.x, 4.x, 5.x, 5.A, 5.B y 7.x)

Contenido del Paquete

Manual del Usuario

Panel Trasero I/O (Opcional)

Configuración completa del Driver CD

23

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

Solución de Problemas

CAUS A PROBABLE SOLUCIÓN

No hay corriente en el sistema. La luz de * Asegúrese que el cable de transmisión corriente no ilumina, ventilador dentro de esté seguramente enchuf ado.

Indicador de luz del teclado apagado.

* Contacte ayuda técnica.

Sistema inoperativo. Luz del teclado * Presione los dos extremos del DIMM, encendido, luz de indicador de corriente iluminado, disco rígido está girando. presione para abajo f irmemente hasta que el módulo encaje en el lugar.

Sistema no arranca desde el disco rígido, * Controle el cable de ejecución desde el puede ser arrancado desde el unidad

óptica. disco hasta el disco del controlador.

Asegúrese de que ambos lados estén enchuf ados con seguridad; controle el tipo de disco en la configuración estándar CMOS.

* Copiando el disco rígido es extremadamente importante. Todos los discos rígidos son capaces de dañarse en cualquier momento.

Sistema solamente arranca desde el * Copie datos y documentos de unidad óptica. Disco rígido puede leer y aplicaciones pueden ser usados pero el aplicación. Vuelva a f ormatear el disco rígido. Vuelv a a instalar las arranque desde el disco rígido es imposible. aplicaciones y datos usando el disco de copiado.

Mensaje de pantalla ”Inv alid * Revise el equipo del sistema.

Conf iguration” o “CMOS Failure.” Asegúrese de que la información conf igurada sea correcta.

No puede arrancar después de instalar el * Fije correctamente el puente segundo disco rígido. master/esclav o.

* Ejecute el programa SETUP y seleccione el tipo de disco correcto.

Llame a una manuf acturación del disco para compatibilidad con otros discos.

24

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

Français

Caractéristiques de U8668-D

CPU

Offre les Socket-478.

Supporte le processeur Intel Pentium 4 jusqu’à 3.06GHz.

Supporte Intel Pentium 4 478 Prescott CPU. (pour v ersion 5.A/5B, et 7.5)

Fonctionnant en Bus Frontal de 400/ 533MHz.

Supporte Hy per-Threading.

Les versions 7.8 et plus ne sont pas compatibles avec les processeurs

Willamette.

Les ventilateurs pour CPU Intel standard sont recommandés.

Chipset

North Bridge: P4M266A

South Bridge: VT8235

Mémoire Principale

Supporte jusqu’à 2 matériels DDR.

Supporte des matériels DDR en 200/266MHz.

La plus grande capacité mémoire est 2Go.

Super E/S

Chipset: ITE IT8705.

Slots

Deux slots de maîtrise de bus PCI 32 bits. (seulment pour version 1.x et 6.x)

Trois slots de maîtrise de bus PCI 32 bits. (seulment pour v ersion 3.x, 4.x, 5.x,

5.A, 5.B, et 7.x)

Un slot CNR. (seulment pour version 3.x, 4.x, 5.x, 5.A, 5.B et 7.x)

Un slot AMR. (seulment pour v ersion 1.x et 6.x)

Un slot AGP

IDE Interne

Supporte quatre disques durs IDE.

Supporte PIO Mode 4, le Mode Maître et le Mode de Maîtrise de Bus Ultra

DMA 33/66/100/133.

LAN (seulment pour version 3.3)

10/100Mbps.

LAN

VT6103/6103L (Seules les versions 7.8 et plus sont compatibles avec le chipset VT6103L).

Double Vitesse: 10/100Mbps.

25

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

Négociation automatique : 10/100 Mbps, Full/Half Duplex.

Codec Son AC’97 Interne

Chipset: VIA1612A (seulment pour v ersion 3.x, 6.x et 7.0-7.6)

Conforme aux spécif ications du codec AC’97.

Codec Son AC’97 Interne (optionnel)

Chipset: CMI9739A (seulment pour v ersion 1.x, 4.x, 5.x, 5.A, 5.B ,7.7, 7.8 et plus)

Conforme aux spécif ications du codec AC’97.

Périphériques Internes

Supporte les lecteurs de disquettes 360K, 720K, 1.2Mo, 1.44Mo et 2.88Mo.

Supporte 1 port série.

Supporte 1 port VGA.

Supporte 1 port parallèle multi-mode. (mode SPP/EPP/ECP)

Supporte souris PS/2 et clav ier PS/2.

Supporte 6 ports USB2.0 (2 x arrières + 4 x avants/4 x arrières + 2 x av ants)

BIOS

AWARD legal Bios.

Supporte la Fonction USB.

Système d’Exploitation

Offre les meilleures perf ormances pour MS-DOS, Windows 2000, Windows

Me, Windows XP, SCO UNIX etc.

Dimensions

Facteur de Forme Micro ATX: 19.5cm X 22.8cm (l X L) (seulment pour v ersion 1.x et 6.x)

Facteur de Forme Micro ATX: 19.5cm X 24.4cm (l X L) (seulment pour v ersion 3.x, 4.x, 5.x, 5.A, 5.B et 7.x)

Contenu de l'Emballage

Câble de Disque Dur

Câble de Lecteur de Disquette

Câble USB (Optionnel)

Panneau d’E/S Arrière (Optionnel)

CD de Pilote Complet

26

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

Dépannage

PROBLÈME SOLUTION

Pas d'alimentation au système. Les v oyants lumineux ne s'allument pas, le v entilateur à l'intérieur du bloc d'alimentation ne se met pas en marche.

Le v oy ant du clavier ne s'allume pas

* Assurez-v ous que le câble d'alimentation est bien branché

* Remplacez le câble

* Contactez le serv ice d'assistance technique.

Le système ne f onctionne pas. Les v oyants du clavier sont allumés, les v oyants de l'alimentation aussi, le disque

* En exerçant une pression uniforme sur les deux extrémités du DIMM, poussez le module vers le bas jusqu'à ce qu'il dur tourne. s'enclenche.

Le système ne se réinitialise pas du disque dur, réinitialisation possible depuis le lecteur lecteur optique.

* Vérif iez le câble du disque à la carte du contrôleur de disque. Assurez-v ous que les deux extrémités sont bien branchées ; vérif iez le type de lecteur dans la conf iguration standard de

CMOS.

* Il est très important d'effectuer des sauv egardes du disque dur. Les disques durs peuv ent tomber en panne

à n'importe quel moment.

Le système ne se réinitialise que depuis le lecteur optique. Le disque dur peut être lu et les applications sont utilisables mais il est impossible d'effectuer de réinitialisation depuis le disque dur.

* Effectuez une sauv egarde des f ichiers des données et d'application.

Ref ormatez le disque dur. Ré-installez les applications et les données sauv egardées sur les disques de secours.

Un message s'affiche indiquant que la conf iguration n'est pas valide ou qu'il y a

* Vérif iez l'équipement du système.

Assurez-v ous que les informations de une panne du CMOS. la conf iguration sont correctes.

Impossible de réinitialiser le système après l'installation d'un deuxième disque dur.

* Réglez les cav aliers maître/esclave correctement.

* Exécutez le programme SETUP et sélectionnez les ty pes de lecteur.

Contactez les fabricants pour toute question de compatibilité avec les autres disques.

27

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

Chapter 3: WarpSpeeder™

3.1 Introduction

[Warp Sp eeder™], a new p owerful control utility, features three user-friendly functions includin g Overclock M anager, Overvoltage

M anager, and Hardware Monitor.

With the Overclock M anager, users can easily adjust the frequency they p refer or they can get the best CPU p erformance with just one click. The Overvoltage Manager, on the other hand, help s to p ower up CPU core voltage and M emory voltage. The cool Hardware

M onitor smartly indicates the temp eratures, voltage and CPU fan sp eed as well as the chip set information. Also, in the About p anel, y ou can get detail descr iptions about BIOS model and chip sets. In addition, the frequency status of CPU, memory, AGP and PCI along with the CPU sp eed are sy nchronically shown on our main p anel.

M oreover, to p rotect users' computer sy stems if the setting is not approp riate when testing and results in sy stem fail or han g,

[Warp Sp eeder™] technology assures the sy stem stability by automatically rebooting the co mputer and then restart to a sp eed that is either the original sy stem sp eed or a suitable one.

OS Sup p ort: Windows 98 SE, Windows M e, Windows 2000,

Windows XP

DirectX: DirectX 8.1 or above. (The Windows XP op erating system includes DirectX 8.1. If you use Windows XP, you do not need to

28

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n install DirectX 8.1.)

3.3 Installation

1. Execute the setup execution file, and then the followin g dialo g will pop up . Please click “Next” button and follow the default p rocedure to install.

2. When y ou see the following d ialo g in setup p rocedure, it means setup is completed. If the “Launch the WarpSp eeder Tray

Utility” checkbo x is checked, the Tray Icon utility and

[WarpSp eeder™] utility will be automatically and immediately launched after y ou click “Finish” button.

29

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

Usage:

The following figures are just only for reference, the screen p rinted in this user manual will ch an ge accordin g to y our motherboard on hand.

30

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

[WarpSpee der™] includes 1 tray icon and 5 pane ls :

1. Tray Icon:

Whenever the Tray Icon utility is launched, it will display a little tray icon on the right side of Windows Taskbar.

This utility is resp onsible for conveniently invoking

[Warp Speeder™] Utility. You can use the mouse by clickin g the left button in order to invoke [WarpSp eeder™] directly from the little tray icon or y ou can right-click the little tray icon to pop up a p op up menu as followin g figure. The

“Launch Utility ” item in the p op up menu has the same function as mouse left-click on tray icon and “Exit” item will close Tray Icon utility if selected.

2. Main Panel

If y ou click the tray icon, [WarpSp eeder™] utility will be invoked. Please refer to the followin g figure; the utility ’s first window y ou will see is M ain Panel.

Main Panel con tains fe ature s as foll ows: a. Disp lay the CPU Sp eed, CPU external clo ck, M emory clock,

AGP clock, and PCI clock information. b. Contains About, Voltage, Over clock, and Hardware M onitor

Buttons for invoking resp ective p anels. c. With a user-friendly Status Animation, it can rep resent 3

31

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n overclock p ercentage stages:

M an walking→overclock percentage from 100% ~ 110

%

Panther running→over clock p ercentage from 110% ~

120%

Car racin g→ov erclock p ercentage from 120% ~ above

3. Voltage Panel

Click the Voltage button in M ain Panel, the button will be high lighted and the Voltage Panel will slide out to up as the followin g figure.

In this p anel, y ou can decide to incr ease CPU core voltage and M emory voltage or not. The default setting is “No”. If you want to get the best p erformance of over clock in g, we

32

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n recommend y ou click the op tion “Yes”.

4. Overclock Panel

Click the Overclo ck button in Main Panel, the button will be high lighted and the Overclo ck Panel will slid e out to left as the following f igure.

33

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

O ve rclock Panel contains the these featu res: a. “–3MHz button”, “-1M Hz button”, “+1MHz button”, and

“+3MHz button”: p rovide user the ability to do real-time overclock adjustment.

Warning:

Manually overclock is potentially dangerous, especially when the overclocking percentage is over 110 %. We strongly recommend you verify every speed you overclock by click the Verify button. Or, you can just click Auto overclock button and let [WarpSpeeder™ ] automatically gets the best result for you. b. “Recovery Dialog button”: Pop up the following d ialo g. Let user select a restoring way if sy stem need to do a fail-safe reboot.

34

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n d. “Auto-overclock button”: User can click this button and

[Warp Sp eeder™] will set the best and stable p erformance and frequency automatically. [Warp Speeder™] utility will execute a series of testing until sy stem fail. Then system will do fail-safe reboot by using Watchdo g function. After reboot, the [Warp Sp eeder™] utility will restore to the hardware default setting or load the verified best and stable frequency accordin g to the Recovery Dialo g’s setting. e. “Verify button”: User can click this button and

[Warp Sp eeder™] will p roceed a testing for curr ent frequency. If the testing is ok, then the current frequency will be saved into system registry. If the testing fail, system will do a fail-saf e rebootin g. After reboot, the

[Warp Sp eeder™] utility will restore to the hardware default setting or load the verif ied best and stable frequency accordin g to the Recovery Dialo g’s setting.

Note:

Because the testing programs, invoked in Auto-overclock and Verify, include

DirectDraw, Direct3D and DirectShow tests, the DirectX 8.1 or newer runtime library is required. And please make sure your display card’s color depth is

High color (16 bit) or True color( 24/32 bit ) that is required for Direct3D rendering.

5. Hardware Monitor Panel

Click the Hardware M onitor button in Main Panel, the button will be highlighted and the Hardware Monitor p anel will slide out to left as the following f igure.

In this p anel, y ou can get the real-time status information of your system. The information will be r efreshed ev ery 1 second.

35

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

6. About Panel

Click the “about” button in M ain Panel, the button will be high lighted and the About Panel will slide out to up as the followin g figure.

In this p anel, y ou can get model name and detail information in hints of all the chip set that are related to overclockin g. You can also get the mainboard ’s BIOS model and the Version number of [Warp Sp eeder™] utility.

36

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

Note:

Because the overclock, overvo ltage, and hardwar e monitor features are controlled by several separate chip set,

[WarpSp eeder™] divide these features to sep arate panels. If one chip set is not on board, the correlative button in M ain p anel will be disabled, but will not interfere other p anels’ functions. This p rop erty can make [Warp Sp eeder™] utility more robust.

37

M o t t t h e r r r b o a r r r d D e s c r r r i i i p t t t i i i o n

06/29/2004

38