Schneider Electric XBT GT GT1100, GT1130, GT2110, GT2120, GT2130, GT2220, GT2330 XBT GT Panel User Manual

Magelis XBT GT User Manual
35010372 01
35010372 01 eng
2.0
2
35010372 01 12/2005
Table of Contents
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
About the Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Part I XBT GT Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Chapter 1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
XBT GT Series of Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Series XBT GT Panels and Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CE Marking Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 2
13
14
17
19
20
XBT GT Device Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
System Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Chapter 3
3.1
3.2
3.3
35010372 01 12/2005
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Structural Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Functional Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory, Clock, and Touch Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interface Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications of Serial Interface COM1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications of Serial Interface COM2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
31
33
33
34
35
37
38
38
39
42
43
45
45
46
51
3
3.4
3.5
Chapter 4
4.1
4.2
4.3
4.4
4.5
4.6
Other Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Part Numbers and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Parts Identification and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Terminal Configuration Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
XBT GT1000 Series Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
XBT GT2000 Series Dimension. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Panel Cut dimension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Installation Fasteners. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Installation and Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
At a glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Installation Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Wiring Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
At a glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Connecting the Power Cord. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Connecting the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Input/Output Line placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Tool Port Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Presentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
USB Data Transfer Cable (XBT ZG925) - USB Driver Installation . . . . . . . . . . . 93
Ethernet Cable Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Presentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
CF Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
CF Card Installation and Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
USB Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Presentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
USB Data Transfer Cable (XBT ZG935) - USB Driver Installation . . . . . . . . . . 103
USB Cable Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Part II Setting and Debugging . . . . . . . . . . . . . . . . . . . . . . . . . . 109
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Chapter 5
5.1
4
Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
XBT GT Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Types of Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Offline Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
System Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
35010372 01 12/2005
Chapter 6
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Troubleshooting Checklists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Self Test List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Chapter 7
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Regular Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Periodic Check Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing the Backlight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index
35010372 01 12/2005
129
130
131
132
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
5
6
35010372 01 12/2005
Safety Information
§
Important Information
Note
Read these instructions carefully, and look at the equipment to become familiar with the
device before trying to install, operate, or maintain it. The following special messages
may appear throughout this documentation or on the equipment to warn of potential
hazards or to call attention to information that clarifies or simplifies a procedure.
The addition of this symbol to a Danger or Warning safety label indicates
that an electrical hazard exists, which will result in personal injury if the
instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential personal
injury hazards. Obey all safety messages that follow this symbol to
avoid possible injury or death.
DANGER
DANGER indicates a hazardous situation, which will result in death, serious injury
or equipment damage.
WARNING
WARNING indicates a situation presenting risks liable to provoke death, serious
injury or equipment damage.
CAUTION
CAUTION indicates a potentially hazardous situation, which,can result in
personal injury or equipment damage.
35010372 01 12/2005
7
Safety Information
Electrical equipment should be serviced only by qualified personnel. No responsibility is
assumed by Schneider Electric for any consequences arising out of the use of this
material. This document is not intended as an instruction manual for untrained persons.
© 2005 Schneider Electric. All Rights Reserved.
8
35010372 01 12/2005
About the Book
At a Glance
Document Scope
This manual describes how to use the Magelis XBT GT device.
Validity Note
Using the Magelis XBT GT device.
Revision History
User Comments
35010372 01 12/2005
Rev. No.
Changes
3
Post Safety
We welcome your comments about this document. You can reach us by e-mail at
[email protected]
9
About the Book
10
35010372 01 12/2005
XBT GT Panels
I
At a Glance
Overview
This part presents XBT GT Panels.
What's in this
Part?
This part contains the following chapters:
35010372 01 12/2005
Chapter
Chapter Name
Page
1
Overview
13
2
XBT GT Device Connectivity
21
3
Specifications
31
4
Installation and Wiring
73
11
XBT GT Panels
12
35010372 01 12/2005
Overview
1
At a Glance
Overview
This chapter presents series of XBT GT Panels and devices connectable to the
XBT GT.
What's in this
Chapter?
This chapter contains the following topics:
35010372 01 12/2005
Topic
Page
XBT GT Series of Panels
14
Package Contents
17
Series XBT GT Panels and Standards
19
CE Marking Notes
20
13
Overview
XBT GT Series of Panels
Introduction
The following presents the XBT GT series of Human Machine Interface products. These
products are graphical touchscreens and have an operating voltage of 24 Volts DC. The
products offered in this series have various features and benefits listed below:
z
z
z
z
XBT GT Part
Number
Screen size,
Resolution of the screen,
Technology and color of the screen,
Communication.
The following table presents the different XBT GT Products:
Part number
Screen size
(inch/cm)
Resolution
Pixel
Mono/Color
Screen
technology
Video
Ethernet
XBT GT1100
3.8"/9,6
QVGA
Amber
STN
No
No
XBT GT1130
3.8"/9,6
QVGA
Amber
STN
No
Yes
XBT GT2110
5.7"/14,4
QVGA
Blue Mode
STN
No
No
XBT GT2120
5.7"/14,4
QVGA
Monochrome
STN
No
No
XBT GT2130
5.7"/14,4
QVGA
Monochrome
STN
No
Yes
XBT GT2220
5.7"/14,4
QVGA
Color
STN
No
No
XBT GT2330
5.7"/14,4
QVGA
Color
TFT
No
Yes
z
z
STN: Scan Twisted Neumatic also known as passive matrix.
TFT: Thin Film Transistors also known as active matrix.
Note: To avoid potential data loss, be sure to back up the XBT GT unit's screen
data regularly.
14
35010372 01 12/2005
Overview
WARNING
RISK OF UNINTENDED EQUIPMENT OPERATION
z
z
z
z
Do not use the XBT GT as the only means of control for critical system functions
such as motor start/stop or power disconnect
Do not use the XBT GT as the only notification device for critical alarms, such
as device overheating or overcurrent
Do not use the XBT GT with aircraft control devices, aerospace equipment,
central trunk data transmission (communication) devices, nuclear power control
devices, or medical life support equipment, due to the reliability requirements of
these industries
Do not use the XBT GT as the only means of control for critical system functions
such as motor start/stop or power disconnect
In the event of backlight or other XBT GT failure, it may be difficult or impossible
to identify a function. Emergency stop, fuel shutoff, or any function that may
present a danger if not immediately executed must be provided independently of
the XBT GT. In addition, the machine control system design should take into
account the possibility of the backlight failing and the operator being unable to
control the machine, or making errors in the control of the machine.
Failure to follow this instruction can result in death, serious injury, or
equipment damage.
Critical systems,
alarms and
handling
Requirements
Critical alarm indicators and system functions require independent and redundant
protection hardware and/or mechanical interlocks.
WARNING
RISK OF BURNS OR EQUIPMENT DAMAGE
Wait at least 10 seconds before restoring power to the XBT GT after turning it off.
Switching the XBT GT off and on too quickly can result in overheating that leads
to personnel burn hazards or equipment damage.
Failure to follow this instruction can result in death, serious injury, or
equipment damage.
35010372 01 12/2005
15
Overview
Handling the
LCD panel
The following characteristics are specific to XBT GT’s LCD unit and shall not be
considered as defects:
z
z
z
LCD screen may show unevenness in the brightness of certain images or may
appear different when seen from outside the specified viewing angle. Extended
shadows, or "Crosstalk" may also appear on the sides of screen images.
LCD screen pixels may contain black and white colored spots and color display
may seem to have changed.
When the same image is displayed on the XBT GT unit’s screen for a long period,
an afterimage may appear when the image is changed. If this happens, turn OFF
the XBT GT, wait 10 seconds and then restart the unit.
Note: Change the screen image periodically and try not to display the same image
for a long period of time.
WARNING
RISK OF SERIOUS EYE AND SKIN INJURY FROM DAMAGED OR
LEAKING LCD PANEL
z
z
z
Do not touch nor handle an XBT GT whose LCD panel appears damaged or
seems to be leaking.
Do not use sharp objects or tools in the vicinity of the LCD touch panel or to
operate its buttons.
Handle the LCD panel carefully to prevent puncture, bursting, or cracking of the
panel material.
The LCD panel's liquid contains an irritant. If the panel is damaged and any of this
liquid is in contact with your skin, immediately rinse the area with running water for
at least 15 minutes. If the liquid gets in your eyes, immediately rinse your eyes with
running water for at least 15 minutes and consult a doctor.
Failure to follow this instruction can result in death, serious injury, or
equipment damage.
16
35010372 01 12/2005
Overview
Package Contents
Introduction
The following items are included in the XBT GT's package. Before using the
XBT GT, please make sure that all items listed here are present:
z
z
z
z
z
z
z
XBT GT Unit,
Power Plug,
Quick Reference Guide,
Screw Installation Fasteners (x4),
Installation Gasket,
USB Holder (except for XBT GT1000 series),
USB Cable Clamp (except for XBT GT1000 series).
This unit has been carefully packed with special attention to quality. However,
should you find anything damaged or missing, please contact your local XBT GT
distributor immediately.
35010372 01 12/2005
17
Overview
XBT GT Package
Contents
The following shows the XBT GT Package Contents:
XBT GT1000 series
Power
Plug
XBT GT2000
Screw Installation
Fastener (x4)
USB Holder
(Not supplied with
XBT GT1000 series)
Revision
Installation Gasket
Installation
Guide
USB Cable Clamp
(Not supplied with
XBT GT1000 series)
You can identify the product version (PV), Revision level (RL), and the Software
version (SV) from the product label sticker pasted on the XBT GT unit.
The following diagram show a typical representation of label sticker:
18
35010372 01 12/2005
Overview
Series XBT GT Panels and Standards
Introduction
The XBT GT series of panels are UL/C-UL listed and CSA Certified.
These units have been developed to conform with the following standards:
z
z
z
z
UL 508 for Industrial Control Equipment,
UL 1604 Electrical Equipment for Use in Class I and Class II Division 2 and Class
III Hazardous Locations,
UL 60950 Standard for Safety of Information Technology Equipment,
CAN/CSA-C22.2, No.14 and No.213 Industrial Control Equipment Miscellaneous
Apparatus - For Hazardous Locations.
UL1604 Conditions of Acceptability and Handling Cautions:
DANGER
RISK OF EXPLOSION AND EQUIPMENT DAMAGE
z
z
z
z
Compatibility: Power, input and output (I/O) wiring must be in accordance with
Class I, Division 2 wiring methods - Article 501- 4(b) of the National Electrical
Code, Groups A, B, C and D Hazardous, NFPA 70 or as specified in section 18152 of the Canadian Electrical Code for installations within Canada and in
accordance with the authority having jurisdiction.
Confirm that the location is not subject to any risk of explosion before
connecting or disconnecting equipment, replacing or wiring modules.
Confirm that the power supply has been turned OFF before disconnecting,
replacing or wiring modules.
Before turning ON, sweep front panel with a damp cloth.
Failure to follow this instruction will result in death, serious injury, or
equipment damage.
35010372 01 12/2005
19
Overview
CE Marking Notes
Introduction
The XBT GT units are CE marked, EMC compliant products.
These units also conform to EN55011 Class A, EN61000-6-2 directives. For detailed
CE marking information, please contact your local XBT GT distributor.
20
Environment
Standards
Compliance with standards
IEC 61131-2, IEC61000-6-2,CISPR11(Class A) UL 508,
CSA C22.2, n°14 & n°213
Product certification
CE, UL/cUL, CSA, Class 1 Div 2 T4A or T5 (UL & CSA)
Operating temperature
0°C + 50°C (32°F 122°F)
Storage temperature
-20 °C + 60°C (-4°F 140°F)
Protection (front panel)
IP 65 - (IEC 60529)
Enclosure Type 4, 4X Indoor use with Screw Installation
Fasteners only.
Protection (rear panel)
IP 20 - (IEC 60529)
ESD withstand
IEC 61000 - 4 - 2
6kV, contact, 8kV air
Radiated radio frequency
electromagnetic field
IEC 61000 - 4 - 3
10 V / m
Electrical fast transient burst
IEC 61000- 4 - 4
2kV (power supply and I/O) 1kV other ports
High Energy Surges
IEC 61000 - 4 - 5
1kV (Differential Mode on power supply)
2kV (common mode on power supply)
Shocks
IEC 60068 - 2 - 27
1/2 sinusoidal pulse for 11ms, 15 g on 3 axes
Vibration
IEC 60068 - 2 - 6
3.5mm 5 Hz to 9 Hz
1 g. 9 Hz to 150 Hz
Pollution Degree
Pollution Degree 2
35010372 01 12/2005
XBT GT Device Connectivity
2
At a Glance
Introduction
This chapter presents for each XBT GT unit the equipment connectable to it.
What's in this
Chapter?
This chapter contains the following topics:
35010372 01 12/2005
Topic
Page
System Design
22
Accessories
24
21
XBT GT Device Connectivity
System Design
Introduction
The following diagrams represent the main selection of equipment connectable to
the XBT GT.
XBT GT1000
series Edit Mode
Peripheral
The following illustration displays XBT GT1000 series edit mode peripheral:
XBT GT1000 series Unit
Personal Computer
To Ethernet
Network (1)
Vijeo
Designer
Tool Connector
Data Transfer Cable
XBTZG915 or
XBTZG925 (USB)
(1) Not available on XBT GT1100
XBT GT2000
series Edit Mode
Peripheral
The following illustration displays XBT GT2000 series edit mode peripherals:
XBT GT2000 series
Personal Computer
To Ethernet
Network (1)
Vijeo
Designer
USB Connector
CF Card (2)
Data Transfer Cable
XBTZG935 (USB)
(1) Not available on XBT GT2110/2120/2220
(2) Not available on XBT GT2110
22
35010372 01 12/2005
XBT GT Device Connectivity
XBT GT1000
Series Run Mode
Peripheral
The following illustration displays XBT GT1000 Series run mode peripherals:
XBT GT1000 Series Unit
To Ethernet
Network (1)
XBT Z***
PLC
(1) Not available on XBT GT1100
XBT GT2000
series Run Mode
Peripheral
The following illustration displays XBT GT2000 series run mode peripherals:
Serial Bar
To Ethernet Network (1)
Code
USB Hub
(Commercial type)
XBT GT2000
Serial printer
COM1
Bar Code Reader (3)
XBT ZG91
USB
COM2 XBT Z*
Parallel printer (4)
CF Card
PLC
XBT Z***
PLC
(1) Not available on XBT GT2110/2120/2220
(2) Not available on XBT GT2110
(3) Bar code Reader validated with Gryphon range of Datalogic
(4) Printer validated with EPSON and HP model: it is available on Vijeo Designer
documentation
35010372 01 12/2005
23
XBT GT Device Connectivity
Accessories
Introduction
The following accessories are used with XBT GT.
XBT GT Serial
Interface Item
The following table presents the Serial Interface item used with XBT GT:
24
Product
Number
Product name
Description
XBT GT series
XBT Z915
Cable
Connect XBT GT COM1 port to a
serial printer.
XBT GT2000
XBT Z9780
XBT Z Cable
Connect XBT GT1000 COM1 port or
XBT GT2000 COM2 port to
Premium, Micro, Twido PLC
XBT GT1000/
GT2000
VW3A8306
XBT Z Cable
Connect XBT GT1000 COM1 port or
XBT GT2000 COM2 port to
derivation box TSXSCA62
XBT GT1000/
GT2000
VW3A8306R10
XBT Z Cable
Connect XBT GT1000 COM1 port or
XBT GT2000 COM2 port to ATV
Drives or to Hub LU9GC3
XBT GT1000/
GT2000
STBXCA4002
XBT Z Cable
Connect XBT GT COM1 port to
Advantys STB
XBT GT2000
TSXPCX1031
XBT Z Cable
Connect XBT GT COM1 port to
Premium, Micro, Twido
XBT GT2000
XBT ZG909
XBT Z Adapter
Cable adapter COM1 D-Sub9 RS485 XBT GT2000
XBT ZG919
XBT Z Adapter
Cable adapter COM1 D-Sub9 RS232 XBT GT2000
XBT ZG939
XBT Z Adapter
Cable adapter COM1 RJ45
XBT GT1000
XBT Z968
XBT Z9680
XBT Z9681
XBT Z Cable
Connect XBT GT COM1 port with
XBTZ adapter to Premium, Micro,
Twido PLC
XBT GT1000/
GT2000
XBT Z9710
XBT Z Cable
Connect XBT GT COM1 port with
XBTZ adapter to Quantum PLC
XBT GT1000/
GT2000
XBT Z9711
XBT Z Cable
Connect XBT GT COM1 port with
XBTZ adapter to Momentum PLC
XBT GT1000/
GT2000
XBT Z908
XBT Z Cable
Connect XBT GT COM1 port with
XBTZ adapter to derivation box
TSXSCA62
XBT GT2000
XBT Z938
XBT Z Cable
Connect XBT GT COM1 port with
XBTZ adapter to ATV drives or to
Hub LU9GC3
XBT GT2000
35010372 01 12/2005
XBT GT Device Connectivity
35010372 01 12/2005
Product
Number
Product name
Description
XBT GT series
XBT Z918
XBT Z Cable
Connect XBT GT COM1 port with
XBTZ adapter to Premium Module
SCY
XBT GT2000
XBT Z988
XBT Z Cable
Connect XBT GT COM1 port with
XBTZ adapter to Advantys STB
XBT GT1000/
GT2000
XBT ZGI232
XBT Z Isolation
Connect XBT GT COM1 port to an
equipment and provide isolation
XBT GT2000
XBT ZGI485
XBT Z Isolation
Connect XBT GT COM1 port to an
equipment and provide isolation
XBT GT2000
XBT ZGCOM1
Port Adapter
Connect XBT GT COM1 port to
optional RS422 equipment
XBT GT2000
XBT ZGCOM2
Port Adapter
Connect XBT GT COM2 port to
optional RS485 equipment
XBT GT2000
XBT ZG9731
XBT Z Cable
Connect XBT GT COM1 to
Mitsubishi PLC A Series Link unit or
to Rockwell DF1 Logix PLC
XBT GT2000
XBT ZG9772
XBT Z Cable
Connect XBT GT COM1 to Mitsubishi
PLC Q Series Link Unit
XBT GT2000
XBT ZG9773
XBT Z Cable
Connect XBT GT COM1 to Mistubishi
PLC A Series CPU Unit
XBT GT2000
XBT ZG9774
XBT Z Cable
Connect XBT GT COM1 to Mistubishi
PLC Q Series CPU Unit
XBT GT2000
XBT ZG9775
XBT Z Cable
Connect XBT GT COM1 to Mistubishi
PLC FX Series CPU Unit
XBT GT2000
XBT ZG9740
XBT Z Cable
Connect XBT GT COM1 to Omron
PLC Sysmac Link Series
XBT GT2000
XBT ZG9722
XBT Z Cable
Connect XBT GT COM1 to RS422
devices
XBT GT2000
XBT ZG9778
XBT Z Cable
XBT GT2000
XBT ZG979
Adapter
Connect XBT GT COM1 with port
adapter to Mistubishi PLC with
Melsec 2 port adapter
XBT ZG949
Adapter
Terminal RS422 block to connect
XBT GT COM1 with port adapter to
RS422 devices
XBT ZG9721
XBT Z Cable
Connect XBT GT1000 COM1 or XBT XBT GT1000/
GT2000 COM2 to Siemens PPI PLC GT2000
XBT ZG9292
XBT Z Cable
Connect XBT GT COM1 to Siemens
MPI PLC
XBT GT2000
XBT GT2000
XBT GT2000
25
XBT GT Device Connectivity
26
Product
Number
Product name
Description
XBT GT series
XBT Z918
XBT Z Cable
Connect XBT GT COM1 port with
XBTZ adapter to Premium Module
SCY
XBT GT2000
XBT Z988
XBT Z Cable
Connect XBT GT COM1 port with
XBTZ adapter to Advantys STB
XBT GT1000/
GT2000
XBT ZGI232
XBT Z Isolation
Connect XBT GT COM1 port to an
equipment and provide isolation
XBT GT2000
XBT ZGI485
XBT Z Isolation
Connect XBT GT COM1 port to an
equipment and provide isolation
XBT GT2000
XBT ZGCOM1
Port Adapter
Connect XBT GT COM1 port to
optional RS422 equipment
XBT GT2000
XBT ZGCOM2
Port Adapter
Connect XBT GT COM2 port to
optional RS485 equipment
XBT GT2000
XBT ZG9731
XBT Z Cable
Connect XBT GT COM1 to
Mitsubishi PLC A Series Link unit or
to Rockwell DF1 Logix PLC
XBT GT2000
XBT ZG9772
XBT Z Cable
Connect XBT GT COM1 to Mitsubishi
PLC Q Series Link Unit
XBT GT2000
XBT ZG9773
XBT Z Cable
Connect XBT GT COM1 to Mistubishi
PLC A Series CPU Unit
XBT GT2000
XBT ZG9774
XBT Z Cable
Connect XBT GT COM1 to Mistubishi
PLC Q Series CPU Unit
XBT GT2000
XBT ZG9775
XBT Z Cable
Connect XBT GT COM1 to Mistubishi
PLC FX Series CPU Unit
XBT GT2000
XBT ZG9740
XBT Z Cable
Connect XBT GT COM1 to Omron
PLC Sysmac Link Series
XBT GT2000
XBT ZG9722
XBT Z Cable
Connect XBT GT COM1 to RS422
devices
XBT GT2000
XBT ZG9778
XBT Z Cable
XBT GT2000
XBT ZG979
Adapter
Connect XBT GT COM1 with port
adapter to Mistubishi PLC with
Melsec 2 port adapter
XBT ZG949
Adapter
Terminal RS422 block to connect
XBT GT COM1 with port adapter to
RS422 devices
XBT ZG9721
XBT Z Cable
Connect XBT GT1000 COM1 or XBT XBT GT1000/
GT2000 COM2 to Siemens PPI PLC GT2000
XBT ZG9292
XBT Z Cable
Connect XBT GT COM1 to Siemens
MPI PLC
XBT GT2000
XBT GT2000
XBT GT2000
35010372 01 12/2005
XBT GT Device Connectivity
XBT GT Tool
Connector
XBT GT USB
Connector
XBT GT Software
35010372 01 12/2005
Product
Number
Product name
Description
XBT GT series
XBT Z9730
XBT Z9731
XBT Z Cable
Connect XBT GT COM1 with XBT Z
adapter to Rockwell DF1 PLC
XBT GT1000
XBT Z9732
XBT Z Cable
Connect XBT GT COM1 with XBT Z
adapter to Rockwell DH485 PLC
XBT GT1000/
GT2000
XBT Z9740
XBT Z Cable
Connect XBT GT COM1 with XBT Z
adapter to Omron PLC Sysmac Link
Series
XBT GT1000
XBT Z9720
XBT Z Cable
Connect XBT GT COM1 with XBT Z
adapter to Siemens 3964/RK512
XBT GT1000/
GT2000
The following table presents the Tool Connector used with XBT GT:
Product
Number
Product name
Description
XBT GT series
XBT ZG915 (for
PC Serial Port)
XBT ZG925 (for
PC USB Port)
Cable
Connects the XBT GT to a personal XBT GT1000
computer. Transfers screen data and
user program(s).
The following table presents the USB Connector used with XBT GT:
Product
Number
Product name
Description
XBT GT series
XBT ZG935
Cable
Connects the XBT GT to a personal
computer. Transfers screen data and
user program
XBT GT2000
XBT ZGUSB
Cable
Extends a USB Host Interface on a
cabinet with waterproofness
XBT GT2000
The following table presents the XBT GT Software:
Product name
Description
Vijeo Designer (version 4.3 or
higher)
Software used to create XBT GT unit project data. It is
installed in a personal computer.
27
XBT GT Device Connectivity
XBT GT Screen
Protection Sheet
XBT GT Spring
Clip Fasteners
XBT GT Compact
Flash Memory
Card Interface
The following table presents the Screen Protection Sheet used with XBT GT:
Product
Number
Product name
Description
XBT GT series
XBT ZG61
Screen
Dirt-resistant sheet used for the XBT XBT GT1000
Protection Sheet GT’s screen. The XBT GT’s touch
panel can be operated with this cover
sheet attached. (5 sheets by pack)
XBT ZG62
Screen
Dirt-resistant sheet used for the XBT XBT GT2000
Protection Sheet GT’s screen. The XBT GT’s touch
panel can be operated with this cover
sheet attached. (5 sheets by pack)
The following table presents the Spring Clip Fasteners used with XBT GT:
Product
Number
Product name
Description
XBT GT series
XBT Z3002 (set
of 12 clips)
Spring Clip
Fasteners
Fasteners to attach toolfree the
XBT GT to a panel (for use only with
a IP65 protection)
XBT GT1000/
2000
The Compact Flash Memory Card is used for the following XBT GT unit:
z
z
z
z
XBT GT2120
XBT GT2130
XBT GT2220
XBT GT2330
This slot accepts a Compact Flash memory Card (CF Card):
z
z
z
z
28
XBT ZGM64 (64 Megabytes)
XBT ZGM128 (128 Megabytes)
XBT ZGM256 (256 Megabytes)
MPCN00CEF00N (512 Megabytes)
35010372 01 12/2005
XBT GT Device Connectivity
Maintenance
Options
35010372 01 12/2005
The following table presents the optional maintenance items available with XBT GT:
Product
Number
Product name
Description
XBT GT series
XBT ZGFIX
Screw
Installation
Fastener
Fasteners to attach the XBT GT to a
panel. (4 fasteners per pack)
XBT GT1000/
2000
XBT ZG51
Installation
Gasket
Provides a moisture resistant seal
when installing the XBT GT range.
Same as the seal included in the
XBT GT’s original package.
XBT GT1000
XBT ZG52
Installation
Gasket
Provides a moisture resistant seal
when installing the XBT GT range.
Same as the seal included in the
XBT GT’s original package.
XBT GT2000
29
XBT GT Device Connectivity
30
35010372 01 12/2005
Specifications
3
At a Glance
Overview
This chapter presents the different XBT GT specifications:
z
z
z
z
z
What's in this
Chapter?
35010372 01 12/2005
General Specifications
Functional Specifications
Interface Specifications
Part Numbers and Functions
Dimensions
This chapter contains the following sections:
Section
Topic
Page
3.1
General Specifications
33
3.2
Functional Specifications
38
3.3
Interface Specifications
45
3.4
Part Numbers and Functions
53
3.5
Dimensions
61
31
Specifications
32
35010372 01 12/2005
Specifications
3.1
General Specifications
At a Glance
Overview
This section presents XBT GT general specifications:
z
z
z
What's in this
Section?
Electrical Specifications
Environmental Specifications
Structural Specifications
This section contains the following topics:
Topic
Electrical Specifications
35010372 01 12/2005
Page
34
Environmental Specifications
35
Structural Specifications
37
33
Specifications
Electrical Specifications
XBT GT
Electrical
Specifications
34
The following table presents the XBT GT’s electrical specifications:
Specification
XBT GT1100
XBT GT1130
XBT GT2110
XBT GT2120
XBT GT2130
XBT GT2220
XBT GT2330
Input Voltage
24V DC
Rated Voltage
19.2 V DC to 28.8 V DC
Allowable Voltage Drop
≤ 1 ms
≤ 10 ms
≤ 5 ms
Power Consumption
≤7W
≤ 18 W
≤ 26 W
In-Rush Current
≤ 50 Α
[The FWHM (Fullwidth, half
maximum) value is
approximately
50µs. (When
exceeding 25A)]
≤ 30 Α
Voltage endurance
between power terminal
and frame ground (FG)
AC 500 V 20mA for 1 minute
Insulation Resistance
between power terminal
and frame ground (FG).
20MΩ or higher at
500V DC
200MΩ or higher at 500V DC
35010372 01 12/2005
Specifications
Environmental Specifications
Introduction
The following are the Environmental Specifications of XBT GT.
XBT GT
Environment
Specifications
The following table presents the XBT GT’s environment specifications:
35010372 01 12/2005
Specification
XBT GT1100
XBT GT1130
XBT GT2110
Ambient operating
temperature (Cabinet
interior & Panel face)
0°C to +50°C (32°F to 122°F) (1)
Storage temperature
-20°C to + 60°C (-4°F to 140°F)
XBT GT2120
XBT GT2130
XBT GT2230
XBT GT2330
Operating humidity
10%RH to 90%RH (Non condensing, wet bulb temperature: ≤ 39°C)
Storage humidity
10%RH to 90%RH (Non condensing, wet bulb temperature: ≤ 39°C
Air purity (Dust)
≤ 0.1mg/m3 (non-conductive levels)
Pollution degree
Pollution degree 2
Corrosive gases
Free of corrosive gases
Atmospheric
endurance (XBT GT
operation altitude)
800hPa to 1,114hPa (2,000 meters [2187.22 yd.] (or lower)
Vibration resistance
IEC61131-2
compliant
z Industry:
5 Hz to 9 Hz
3.5mm, 9 Hz to
150 Hz 1g.
IEC61131-2 compliant
z Industry:
10 Hz to 57 Hz 0.075mm, 57 Hz to 150
Hz 1g.
Noise immunity (via
noise simulator)
Noise voltage:
1000Vp-p.
Pulse duration: 1µ
sec.
Rise time:1n sec.
Noise voltage: 1,200Vp-p.
Pulse duration: 1µ sec.
Rise time: 1n sec.
Electrostatic
discharge immunity
6kV contact (complies with EN 61000-4-2 level 3)
35
Specifications
Note: (1) The LCD displays of XBT GT1100/1130/2110/2120/2130/2220/2330
may occasionally blur when they are used for hours at over 40°C [104°F] ambient
operating temperature. After the temperature returns to normal, the display will be
restored to normal. The XBT GT’s operation will not be affected even though the
display is blurred.
CAUTION
RISK OF EQUIPMENT DAMAGE
Do not store the XBT GT in an area where the temperature is lower than the
temperature recommended in the XBT GT unit's specifications. Doing so may cause
the LCD display's liquid to freeze, which can damage the LCD. Also, if the storage
area's temperature becomes higher than the specified level, the LCD's liquid may
become isotropic, causing irreversible damage to the LCD. Therefore, only store the
XBT GT in areas where temperatures are within the XBT GT unit's specifications and
do not restrict nor block the XBT GT unit's rear-face ventilation slots.
Failure to follow this instruction can result in injury or equipment damage.
Air quality and
Temperature
requirements
Observe the following environmental requirements when using XBT GT:
z
Do not operate or store the XBT GT where chemicals evaporate, or where
chemicals are present in the air:
z Corrosive chemicals: Acids, alkalines, liquids containing salt.
z Flammable chemicals: Organic Solvents.
WARNING
RISK OF EXPLOSION OR ELECTRIC SHOCK
Do not allow water, liquids, metal, and wiring fragments to enter the XBT GT unit's
case, since they can cause either a malfunction or an electric shock.
Do not use the XBT GT in an environment where flammable gases are present as
it may cause an explosion.
Failure to follow this instruction can result in death, serious injury, or
equipment damage.
36
35010372 01 12/2005
Specifications
Structural Specifications
Introduction
The following are the Structural Specifications of XBT GT.
XBT GT
Structural
Specifications
The following table presents the XBT GT’s structural specifications:
Specification
XBT GT1100
XBT GT1130
XBT GT2110
XBT GT2120
XBT GT2130
XBT GT2220
XBT GT2330
Grounding
Observe local codes and standards. Ensure the ground connection
has a resistance ≤ 100W and that the ground wire has a cross
section of at least 2mm or 14AWG.
Rating (For front panel Equivalent to IP65 (IEC 60529) (1) NEMA # 250 Type 4X/12
or installed unit)
External dimensions
W130 mm [5.12 in] x
H104 mm [4.09 in] x
D41 mm [1.61 in]
W167.5 mm [6.60 in] x H135 mm [5.32 in] x
D59.5 mm [2.34 in]
Weight
≤ 0.4Kg (0.9lb)
≤ 1.0Kg (2.20lb)
Cooling Method
Natural air circulation
Note: (1) The front face of the XBT GT unit, installed in a solid panel, has been
tested using conditions equivalent to the standards shown in the specification.
Therefore, prior to installing the XBT GT be sure to confirm the type of conditions
that will be present in the XBT GT’s operating environment. If the installation
gasket is used for a long period of time, or if the unit and its gasket are removed
from the panel, the original level of the protection cannot be guaranteed. To
maintain the original protection level, replace the installation gasket every year.
35010372 01 12/2005
37
Specifications
3.2
Functional Specifications
At a Glance
Overview
This section presents XBT GT Functional Specifications:
z
z
z
What's in this
Section?
38
Display
Memory
Interfaces
This section contains the following topics:
Topic
Page
Display
39
Memory, Clock, and Touch Panel
42
Interface
43
35010372 01 12/2005
Specifications
Display
Introduction
The following are the XBT GT Display Specifications.
STN Display
XBT GT unit
The following table presents the display specification of XBT GT unit with STN
screen technology:
35010372 01 12/2005
Specification
XBT GT1100
XBT GT1130
XBT GT2110
XBT GT2120
XBT GT2130
XBT GT2220
Type
Monochrome
LCD
Monochrome
(Blue mode)
LCD
Monochrome
(B&W) LCD
Color
Resolution (pixels)
320 x 240
Active Display Area
WxH (mm)
WxH (in.)
76.7 x 57.5
115.2 x 86.4
3.02 x 2.26
4.54 x 3.40
Colors
8 levels of
gray)
16 gradations
4.096 colors
Backlight (1)
LED Backlight
(Color: Amber;
Service life:
50,000 h. [half
of original
brightness])
(Color: Red;
Service
life:10,000 h.
[half of original
brightness])
CFL Backlight (Service life:
58,000 h. at 25°C and continuos
operation [half of original
brightness])
CFL Backlight
(Service life:
75,000 h. at
25°C and
continuos
operation [half
of original
brightness])
Contrast Adjustment
8 levels of adjustment available via touch panel.
Brightness
Adjustment
2 levels of
adjustment
available via
touch panel.
System Embedded
Language Fonts (2)
ASCII: (Code page 850) Alphanumeric (including European
characters) Chinese: (GB2312-80 codes) simplified Chinese fonts
Japanese: ANK 158, Kanji: 6,962 (JIS Standards 1 & 2) (including
607 non-kanji characters) Korean: (KSC5601 - 1992 codes) Hangul
fonts Taiwanese: (Big 5 codes) traditional Chinese fonts
Character Sizes (2)
8 X 8, 8 X 16, 16 X 16 and 32 X 32 pixels fonts
8 levels of adjustment available via touch panel.
39
Specifications
Specification
XBT GT1100
XBT GT1130
XBT GT2110
XBT GT2120
XBT GT2130
XBT GT2220
Font Sizes
Width can be expanded 1 to 8 times. Height can be expanded 1/2 and
1 to 8 times.
8 x 8 pixels
40 Char. per row, x 30 rows
8 x 16 pixels
40 Char. per row, x 15 rows
16 x 16 pixels
20 Char. per row x 15 rows
32 x 32 pixels
10 Char.per row x 7 rows
Note:
z (1) Among backlight units there may be slight variations in illumination color,
however, this does not effect the performance or quality of the XBT GT unit.
z (2) The display font will differ depending on which (language) character, or
which size you select. Also, if Vijeo Designer 4.3 or later software is used,
additional high quality fonts are available with 16x16 or larger characters.
40
35010372 01 12/2005
Specifications
TFT Display
XBT GT unit
The following table presents the display specification of XBT GT unit with TFT
screen technology:
Specification
XBT GT2330
Type
TFT Color LCD
Resolution (pixels)
320 x 240
Active Display Area
WxH (mm)
WxH (in.)
76.7x57.5
Colors
65.536 colors
Backlight (1)
CFL Backlight (Service life: 50,000 h. at 25°C and continuos operation
[half of original brightness])
3.02x2.26
Contrast Adjustment Not available.
Brightness
Adjustment
8 levels of adjustment available via touch panel.
Language Fonts
ASCII: (Code page 850) Alphanumeric (including European
characters) Chinese: (GB2312-80 codes) simplified Chinese fonts
Korean: (KSC5601 - 1992 codes) Hangul fonts Taiwanese: (Big 5
codes) traditional Chinese fonts
Character Sizes (2)
8 X 8, 8 X 16, 16 X 16 and 32 X 32 pixel fonts
Font Sizes
Width can be expanded 1 to 8 times. Height can be expanded 1/2 and
1 to 8 times.
8 x 8 pixels
40 Char. per row, x 30 rows
8 x 16 pixels
40 Char. per row, x 15 rows
16 x 16 pixels
20 Char. per row x 15 rows
32 x 32 pixels
10 Char.per row x 7 rows
Note:
z (1) Among backlight units there may be slight variations in illumination color,
however, this does not effect the performance or quality of the XBT GT unit.
z (2) The display font will differ depending on which (language) character, or
which size you select. Also, if Vijeo Designer 4.3 or later software is used,
additional high quality fonts are available with 16x16 or larger characters.
35010372 01 12/2005
41
Specifications
Memory, Clock, and Touch Panel
Memory
The following table presents the specification memory of each XBT GT unit:
Memory
XBT GT1100
XBT GT1130
XBT GT2000 series
Application Flash EPROM
8 Megabytes
16 Megabytes
Data Backup SRAM uses a
lithium battery (1)
512 Kilobytes
512 Kilobytes
Application run DRAM
16 Megabytes
32 Megabytes
Legend:
(1) A Lithium battery life is:
z 10 years when the battery's ambient temperature is ≤ 40°C (104F.).
z 10 years when the unit's ambient temperature is ≤ 25°C (77F.).
When used for backup: (without main power):
z Approximately 60 days, with a fully charged battery.
z Approximately 6 days, with a 10% charged battery.
Clock
WARNING
UNINTENDED EQUIPMENT OPERATION
Variations in operating conditions and battery life can cause a clock error from 380 to +90 seconds per month. The user should monitor the time and adjust the
time as needed to satisfy the system needs.
Failure to follow this instruction can result in death, serious injury, or
equipment damage.
Touch Panel and
Function Keys of
XBT GT
42
The following table presents the touch panel and function keys of XBT GT unit:
Specification
XBT GT1000
XBT GT2000
Touch panel resolution
8 x 6 matrix
1 or 2 point push, selectable
Analog typing system
1024x1024 resolution, (Single
point push selectable)
Function keys
6 switches
-
35010372 01 12/2005
Specifications
Interface
Introduction
All XBT GT displays are provided with a Serial Interface, and Tool Port or USB
Connector.
Serial Tool Port
Connector
The following table describes the Tool port of XBT GT1100/1130
Serial Interface
COM1
Interface
Description
Tool Port Connector
Asynchronous TTL level nonprocedural interface
command
Used for transferring data user program to and from the
Vijeo Designer and XBT GT.
The following table describes the Serial Interface of XBT GT1100/1130
Interface
Description
Serial interface COM1 RJ45
Asynchronous Transmission
RS232C / RS485
Data Length
7 or 8 bits
Stop Bit
1 or 2 bits
Parity
None, Odd or Even
Data Transmission Speed
2,400bps to 115,200bps
The following table lists the Serial Interface of XBT GT2110/2120/2130/2220/2330
units.
Interface
Description
Serial interface COM1 D-Sub9
35010372 01 12/2005
Asynchronous Transmission
RS232C/RS422
Data Length
7 or 8 bits
Stop Bit
1 or 2 bits
Parity
None, Odd or Even
Data Transmission Speed
2,400bps to 115,200bps
43
Specifications
Serial Interface
COM2
The following table lists the serial interfaces COM2 of XBT GT2110/2120/2130/
2220/2330 units.
Interface
Description
Serial interface COM2 RJ45
Serial Interface
Ethernet
Serial Interface
USB and Memory
Card
Asynchronous Transmission
RS485
Data Length
7 or 8 bits
Stop Bit
1 or 2 bits
Parity
None, Odd or Even
Data Transmission Speed
2,400bps to 12Mbps (except for
XBT GT2110:115,200bps)
The following table lists the serial interface Ethernet available for XBT GT1130/
2130/2330:
Interface
Description
Ethernet RJ45
IEEE802.3, 10Base-T (XBT GT1000), 10Base-T/
100Base-T (XBT GT2000)
The following table lists the serial interface USB and Memory card available for XBT
GT2000:
Interface
Description
USB TYPE-A x 1
USB 1.1 host I/F
CF Card slot (TYPE-II (except XBT Compact Flash
GT2110)
44
35010372 01 12/2005
Specifications
3.3
Interface Specifications
At a Glance
Overview
This section presents interface specifications of XBT GT units:
z
z
What's in this
Section?
Specification of serial interface COM1
Other interfaces
This section contains the following topics:
Topic
Specifications of Serial Interface COM1
35010372 01 12/2005
Page
46
Specifications of Serial Interface COM2
51
Other Interfaces
52
45
Specifications
Specifications of Serial Interface COM1
Introduction
This interface is used to connect:
z
z
XBT GT1000 to remote equipment, via an RS232C or RS485 cable. The
connector used is a RJ45-type connector.
XBT GT2000 to remote equipment, via an RS232C or RS422 cable. The
connector used is a D-Sub9 connector.
DANGER
RISK OF ELECTRIC SHOCK OR EQUIPMENT DAMAGE
When connecting an external device to the XBT GT with the SG terminal, be sure
to check that no short-circuit loop is created when you setup the system.
z The XBT GT unit’s Serial Port is not isolated. The #8 SG (XBT GT1100/1130 Signal
Ground) terminal must be connected to remote equipment when the host (PLC) unit
is not isolated. To reduce the risk of damaging the RS232C/RS485 circuit, make
sure to connect the #8 SG (Signal Ground) terminal to the appropriate equipment.
z The SG (Signal Ground) and the FG (Frame Ground) terminals are connected
inside the XBT GT unit.
Failure to follow this instruction will result in death, serious injury, or
equipment damage.
46
35010372 01 12/2005
Specifications
XBT GT1100/
1130 Serial
Interface COM1
This interface is used to connect a RS-232C/RS485 serial cable to XBT GT. An
RJ45 8-pin plug connector is used.
The following table describes the XBT GT1100/1130 pin’s serial interface used with
RS-232C/RS485 serial cable.
Pin Connection
Pin
Signal Name
Direction
Meaning
1
RxD
Input
Receive Data
(RS232C)
2
TxD
Output
Send Data (RS232C)
3
Not connected
-
-
4
D1
Output/Input
Transfer Data
(RS485)
5
D0
Output/Input
Transfer Data
(RS485)
6
RTS
Output
Request To Send
7
Not connected
-
-
8
SG
-
Signal Ground
Front
WARNING
RISK OF UNINTENDED EQUIPMENT OPERATION AND EQUIPMENT
DAMAGE
z
z
z
z
Ensure that all connections to the communication ports on the bottom and sides
of the unit are not putting excessive stress on the ports.
Securely attach communication cables to the panel or cabinet.
Use only RJ45 cables with a locking tab in good condition.
Use RJ45 connectors with locking system.
An excessive weight or stress on communication cables may cause an
equipment’s disconnection and unintended equipment operation.
Failure to follow this instruction can result in death, serious injury, or
equipment damage.
35010372 01 12/2005
47
Specifications
WARNING
RISK OF EQUIPMENT DAMAGE AND POWER LOSS
z
z
z
z
Avoid excessive stress on the power cable to prevent accidental disconnection.
Securely attach power cables to the panel or cabinet.
Use the designated torque to tighten the unit’s terminal block screws.
Install and fasten unit on installation panel or cabinet prior to connecting Power
Supply and Communication lines.
Excessive stress on the power connection or attempting to install a unit with the
power cables connected may disconnect or cause damage to the power
connections, which can cause short circuits, fire or incorrect operation.
Failure to follow this instruction can result in death, serious injury, or
equipment damage.
48
35010372 01 12/2005
Specifications
XBT GT2110/
2120/2130/2220/
2330 Serial
Interface COM1
The following table describes the XBT GT2110/2120/2130/2220/2330 pin’s serial
interface with a D-Sub9 type connector via an RS232C cable.
Pin Connection
5
1
Pin
Signal Name
Direction
Meaning
1
CD
Input
Carrier Detect
2
RD(RXD)
Input
Receive Data
3
RD(RXD)
Output
Send Data
4
ER(DTR)
Output
Data Terminal
Ready
5
SG
-
Signal Ground
6
DR(DSR)
Input
Data Set Ready
7
RS(RTS)
Output
Request to Send
9
6
8
CS(CTS)
Input
Send Possible
9
CI(RI)/VCC
Input
Called status
display/+5V5%
Output 0.25A
Shell
FG
-
Frame Ground
(Common with
SG)
The following table describes the XBT GT2110/2120/2130/2220/2330 pin’s serial
interface with a D-Sub9 type connector via an RS422 cable.
Pin Connection
5
1
35010372 01 12/2005
Pin
Signal Name
Direction
1
RDA
Input
Receive Data A (+)
2
RDB
Input
Receive Data B (-)
3
SDA
Output
Send Data A (+)
4
ERA
Output
Data Terminal Ready
A (+)
5
SG
-
Signal Ground
6
CSB
Input
Send Possible B (-)
7
SDB
Output
Send Data B (-)
8
CSA
Input
Send Possible (A)
9
ERB
Input
Data Terminal Ready
B (-)
Shell
FG
-
Frame Ground
(Common with SG)
9
6
Meaning
49
Specifications
WARNING
RISK OF UNINTENDED EQUIPMENT OPERATION AND EQUIPMENT
DAMAGE
z
z
z
z
Ensure that all connections to the communication ports on the bottom and sides
of the unit are not putting excessive stress on the ports.
Securely attach communication cables to the panel or cabinet.
Use only D-Sub9 cables with a locking system in good condition.
Use D-Sub9 connectors with locking system.
An excessive weight or stress on communication cables may cause an
equipment’s disconnection and unintended equipment operation.
Failure to follow this instruction can result in death, serious injury, or
equipment damage.
WARNING
RISK OF EQUIPMENT DAMAGE AND POWER LOSS
z
z
z
z
Avoid excessive stress on the power cable to prevent accidental disconnection.
Securely attach power cables to the panel or cabinet.
Use the designated torque to tighten the unit’s terminal block screws.
Install and fasten unit on installation panel or cabinet prior to connecting Power
Supply and Communication lines.
Excessive stress on the power connection or attempting to install a unit with the
power cables connected may disconnect or cause damage to the power
connections, which can cause short circuits, fire or incorrect operation.
Failure to follow this instruction can result in death, serious injury, or
equipment damage.
50
35010372 01 12/2005
Specifications
Specifications of Serial Interface COM2
Introduction
This interface that is used to connect the XBTGT2110/2120/2130/2220/2330 to the Remote
Equipment, via RS485 cable. The connector used is a RJ45-8-pin type connector.
DANGER
RISKS OF ELECTRIC SHOCK OR EQUIPMENT DAMAGE
When connecting an external device to the XBT GT2000 with the SG terminal, be
sure to check that no short-circuit loop is created when you setup the system.
z The XBT GT2000 unit’s Serial Port is not isolated. The #8 SG (XBT GT2000 Signal
Ground) terminal must be connected to remote equipment when the host (PLC) unit
is not isolated. To reduce the risk of damaging the RS485 circuit, make sure to
connect the #8 SG (Signal Ground) terminal to the appropriate equipment.
z The SG (Signal Ground) and the FG (Frame Ground) terminals are connected
inside the XBT GT2000 unit.
Failure to follow this instruction will result in death, serious injury, or
equipment damage.
XBTGT2110/
2120/2130/2220/
2330 Serial
Interface COM2
with RS485 cable
This interface is used to connect a RS485 serial cable to XB GT2000. RJ45 8-pin
plug connector is used.
The following table describes the XB GT2000 pin’s serial interface used with RS485
COM2 serial cable.
Pin Connection
Front
35010372 01 12/2005
Pin
Signal Name
Direction
Meaning
1
Not connected
-
-
2
Not connected
-
-
3
Not connected
-
-
4
D1
Output/Input
Transfer Data
(RS485)
5
D0
Output/Input
Transfer Data
(RS485)
6
RTS
Output
Request To Send
7
Not connected
-
-
8
SG
-
Signal Ground
51
Specifications
Other Interfaces
XBT GT Ethernet
Interface
The Ethernet Interface is used for the following XBT GT unit:
z
z
z
XBT GT1130
XBT GT2130
XBT GT2330
This interface complies with the IEEE802.3 standard for Ethernet 10BASE-T
(XBT GT1000), 10BaseT/100Base-TX (XBT GT2000) connections.
The following table describes the LED colors and status:
LED
Contents
Orange
z When the Power Supply is ON: LED lights up.
Green
When linking: LED lights up.
z When sending or receiving: LED blinks.
XBT GT USB
Interface
The USB Interface accepts a USB data transfer cable and is used for the following
XBT GT unit:
z
z
z
z
z
52
XBT GT2110
XBT GT2120
XBT GT2130
XBT GT2220
XBT GT2330
35010372 01 12/2005
Specifications
3.4
Part Numbers and Functions
At a Glance
Overview
This section presents the Part Number and Functions of XBT GT unit.
What's in this
Section?
This section contains the following topics:
35010372 01 12/2005
Topic
Page
Parts Identification and Functions
54
Terminal Configuration Switches
58
53
Specifications
Parts Identification and Functions
Introduction
XBT GT1100 and
XBT GT1130
Parts
Identification
The following diagram show display the Parts Identification and functions of the
XBT GT Unit:
Side
XBT GT1100 Part Identification
XBT GT1130 Part Identification
Front
G
G
C
C
A,B
A,B
Rear
F
F
Bottom
H
54
E
D
I
H
E
D
35010372 01 12/2005
Specifications
Description of
XBT GT1100/
1130
XBT GT2000
series Parts
Identification
This following table presents description of part identification for XBT GT1100/1130:
Part
Description
A
Display: displays User created screens and Remote Equipment Variables.
B
Touch Panel: performs screen change operations and sends data to the host (PLC).
C
Power LED: LED ON
D
Power Input Terminal Block: connects the XBT GT power cable’s input and ground
wires to the XBT GT.
E
Serial I/F (host I/F 8 pin RJ45): connects a RS-232C or RS485 (Serial) cable (from
the host/PLC) to the XBT GT (Y Port).
F
Tool Port Connector: connects the Data Transfer Cable to the XBT GT.
G
Function Switches (R1 to R6): used for function keys.
H
RS485 Line Polarization.
I
Ethernet Interface (except for XBT GT1100): permits to connect the XBT GT unit (X
Port) to PLC from a Ethernet cable.
Side
XBT GT2000 series Part Identification
Front
A,B
C
Rear
D
E
35010372 01 12/2005
55
Specifications
Side
XBT GT2000 series Part Identification
Left and Right
H
F
I
J
G
K
Left
CF Card
Cover Open
Right
L
M
56
35010372 01 12/2005
Specifications
Description of
XBT GT2000
series
35010372 01 12/2005
This following table describes the parts identification of XBT GT2000 series:
Part
Description
A
Display: displays User created screens and Remote Equipment Variables.
B
Touch Panel: performs screen change operations and sends data to the host (PLC).
C
Status LED:
z Green (lit): Normal operation (Power is ON) or OFFLINE operation.
z Orange (lit) (Green + red): Backlight burnout is detected.
z Orange (blinking) (Green + Red): During Software startup.
z Red (lit): When Power is turned ON
z Not lit: Power is OFF
D
Expansion unit Interface: Connects expansion units with communication features.
E
CF Card Access Lamp (except XBT GT2110:
z Green ON: The CF Card is inserted and the Cover is closed, or the CF Card is
being accessed.
z Green OFF: The CF Card is not inserted or is not being accessed.
F
Ethernet Interface (10BASE-T/100BASE-TX) (except XBT GT2110/2220: RJ-45
connector is used, and the LED turns ON or OFF to indicate the current status.
z Green ON: Data transmission available.
z Green OFF: No connection or subsequent transmission failure.
z Yellow ON: Data transmission is occurring.
z Yellow OFF: No data transmission.
G
Power Input Terminal Block: connects the XBT GT power cable’s input and ground
wires to the XBT GT.
H
USB Interface (USB1.1): Connects a data transfer cable to XBT GT.
I
Serial Interface COM1: Connects a RS232C or RS422 (Serial) cable (from the host/
2CC) to the XBT GT (COM1 port).
J
Serial Interface COM2: Connects a RS488 (Serial) cable (from the host/2LC) to the
XBT GT (COM2 port).
K
Polarization Switch Selector.
L
CF Card Cover (except XBT GT2110): Covers the CF Card Slot. This cover must be
closed when accessing to the CF Card.
M
CF Card Socket: Permits to insert the CF Card in this slot.
57
Specifications
Terminal Configuration Switches
Introduction
The RS485 Line Polarization Selector Switch is available on:
z
z
z
z
z
z
z
XBT GT1100
XBT GT1130
XBT GT2110
XBT GT2120
XBT GT2130
XBT GT2220
XBT GT2330
The CF Card Dip Switches are available on:
z
z
z
z
XBT GT Location
RS485 Line
Polarization
Selector Switch
XBT GT2120
XBT GT2130
XBT GT2220
XBT GT2330
On XBT GT1100/1130 and XBT GT2110/2120/2130/2220/2330, the RS485 line
polarization Selector Switch is located next to the RJ45 Serial Port.
The following illustration displays the location of the RS485 line polarization Selector
Switch on XBT GT units:
Selector Switch
XBT GT1000
58
Selector Switch
XBT GT2000
35010372 01 12/2005
Specifications
XBT GT
Parameters of
RS485 Line
Polarization
Selector Switch
The following table explains XBT GT1100/1130 and XBT GT2110/2120/2130/2220/
2330 units’ RS485 Line Polarization parameters:
Selector
Switch
Function
ON
1
Controls the
polarization of
RS485 serial line.
No polarization.
RS485 Serial line is
polarized (620 Ω pull up
on D1 and 620 Ω pull
down on D0).
XBT GT Location
of CF card Dip
Switches
OFF
Note
The polarization shall be activated if
Modbus protocol has to be
implemented and no other equipment
performs polarization on the bus.
On XBT GT2120/2130/2220/2330, the CF Card Dip Switches are located below the
CF Card Cover.
The following illustration displays the location of the CF Card Dip Switches on XBT
GT2120/2130/2220/2330:
ON
1
35010372 01 12/2005
2
3
4
59
Specifications
XBT GT
Parameter of CF
Card Dip
Switches
The following table explains XBT GT2120/2130/2220/2330 units’ CF Card Dip
Switches parameters:
Dip
Switch
Function
1
This Dip switch setting controls the startup from a CF Card.
When there is no startup
data in the XBT GT
memory.
ON
Startup is done from the CF Card(*)
and the data is also transferred into
the XBT GT memory.
OFF
A system
message
appears.
Note
(*): Startup data is
required in the CF
Card.
Start up is done
When there is valid startup Startup is done from the CF Card*
and the XBT GT memory is updated. from the XBT
data in the
XBT GT
GT memory.
memory.
Download is available.
Download is not
available.
-
2
This Dip switch allows
download application on
XBT GT products.
3
Reserved
-
-
-
4
This setting controls the
forced closing of the CF
Card cover.
Forced close enabled.
Forced close
disabled.
Used when CF
Card cover is
damaged.
60
35010372 01 12/2005
Specifications
3.5
Dimensions
At a Glance
Overview
This section presents all the dimensions of XBT GT units.
What's in this
Section?
This section contains the following topics:
35010372 01 12/2005
Topic
Page
XBT GT1000 Series Dimensions
62
XBT GT2000 Series Dimension
65
Panel Cut dimension
69
Installation Fasteners
70
61
Specifications
XBT GT1000 Series Dimensions
Introduction
The following dimensions are given in mm and inches and apply to all XBT GT
Series units.
Dimensions
The following illustrations display the dimensions of XBT GT1100/1130:
Top
Front
62
Right Side
35010372 01 12/2005
Specifications
Installation with
Spring Clips
The following illustrations display the external dimensions of the XBT GT1100/1130
unit with Spring Clips:
Top
Front
Right Side
Note: Spring Clip fasteners have to be ordered separately (ref. XBT Z3002)
35010372 01 12/2005
63
Specifications
Installation with
Screw Fasteners
The following illustrations display the external dimensions of the XBT GT1100/1130
unit with Screw Fasteners:
Top
Front
64
Right Side
35010372 01 12/2005
Specifications
XBT GT2000 Series Dimension
Introduction
The following dimensions given in millimeters and inches apply to all XBTGT2000
Series units.
Dimensions
The following illustrations display the dimensions of XBT GT2110/2120/2130/2220/2330:
Top
Front
35010372 01 12/2005
Right Side
65
Specifications
Dimensions with
Cables
The following illustrations displays the dimensions of XBT GT2110/2120/2130/
2220/330 with cables.
Top
Left
66
Back
Right
35010372 01 12/2005
Specifications
Installation with
Spring Clips
The following illustrations display the external dimensions of the XBT GT2110/2120/
2130/2220/2330 unit with Spring Clips:
Top
Front
Right Side
Note: Spring Clip fasteners have to be ordered separately (ref. XBT Z3002)
35010372 01 12/2005
67
Specifications
Installation with
Screw Fasteners
The following illustrations display the external dimensions of the XBT GT2110/2120/
2130/2220/2330 unit with Screw Fasteners:
Top
Front
Right Side
Bottom
68
35010372 01 12/2005
Specifications
Panel Cut dimension
Introduction
Create a panel cut-out and insert the XBT GT into the panel from the front.
Inserting a
XBT GT
The following presents principle of panel cut, (example for XBT GT1000 series),
dimensions are in mm and in inches:
Panel
A
Under 4-R3
B
XBT GT 1000
Dimensions
The following table presents all panel cut’s dimensions in function of XBT GT unit:
XBT GT
A (mm)
XBT GT1100
XBT GT1130
+1
118.5
-0
XBT GT2110
XBT GT2120
XBT GT2130
XBT GT2220
XBT GT2330
35010372 01 12/2005
C
+1
156
-0
B (mm)
A (in.)
B (in.)
C (mm)
C (in.)
+ 0.04
3.64
-0
1.6 to 5.0
0.06 to 0.2
-0
+ 0.04
4.67
-0
+1
123.5
-0
+ 0.04
6.14
-0
+ 0.04
4.86
-0
1.6 to 5.0
0.06 to 0.2
+1
92.5
69
Specifications
Installation Fasteners
Introduction
Two types of fasteners are used to mount the XBT GT range:
z
z
Screw Installation Fasteners,
Spring Clips.
Quantities of fasteners to install XBT GT units.
XBT GT
Spring Clips
Screw Installation Fasteners (1)
XBT GT1100
XBT GT1130
2
4
XBT GT2100
XBT GT2120
XBT GT2130
XBT GT2220
XBT GT2330
2
4
(1) Delivered with XBT GT unit
XBT GT Spring
Clip Dimensions
70
The following illustration shows the dimensions of the Spring Clip in mm and in inch:
35010372 01 12/2005
Specifications
XBT GT Screw
Installation
Fasteners
Dimensions
35010372 01 12/2005
The following illustration shows the dimensions of the Screw Installation Fasteners
in mm and in inch:
71
Specifications
72
35010372 01 12/2005
Installation and Wiring
4
At a glance
Overview
This chapter describes the installation procedures and the wiring principles of XBT
GT.
What's in this
Chapter?
This chapter contains the following sections:
35010372 01 12/2005
Section
Topic
Page
4.1
Installation
75
4.2
Wiring Precautions
82
4.3
Tool Port Connector
91
4.4
Ethernet Cable Connector
96
4.5
CF Card
98
4.6
USB Port
101
73
Installation and Wiring
74
35010372 01 12/2005
Installation and Wiring
4.1
Installation
Installation Procedures
Introduction
Before installing the XBT GT product into a cabinet or panel, read the instructions
below.
The installation gasket and installation fasteners (Screw Installation Fasteners or
Spring Clips) are required when installing the XBT GT.
Gasket setup
requirements
The following table describes the Gaskets setup requirements to be taken:
Stage
Description
1
Before installing the XBT GT into a cabinet or panel, check that the Installation
gasket is securely attached to the unit.
2
A gasket which has been used for a long period of time may have scratches or dirt
on its surface, and could have lost much of its dust and drip resistance. Be sure to
change the gasket once a year or when scratches or dirt become visible.
3
Do not insert the joint of the installation gasket in the corner of the XBT GT. Insert
the joint only in the straight sections of the groove preferably at the bottom of the
product. If you do it, the joint will be pulled so that it may cause the installation
gasket to be torn.
4
To ensure a maximum level of moisture resistance to the installation gasket, make
sure the gasket is inserted into the panel bottom face as shown in the following
illustrational:
Gasket
Rear face of XBT GT
35010372 01 12/2005
75
Installation and Wiring
Panel setup
procedure
The following table describes the Panel setup procedure to be taken:
Stage
Description
1
Check that the installation panel or cabinet’s surface is flat, in good condition and
has no jagged edges. Also, if desired, metal reinforcing strips can be attached to
the inside of the panel, near the Panel Cut, to increase the panel’s resistance
2
Panel thickness (See Panel cut dimensions) depends on the XBT GT unit. Decide
the panel’s thickness based on the level of panel strength required. (1.6mm
(0.06inch) to 10mm (0.4inch) for XBT GT1100/1130.)
3
Be sure that the ambient operation temperature and the ambient humidity are
within their designated ranges. (When installing the XBT GT in a cabinet or
enclosure, the term "ambient operation temperature" indicates the cabinet or
enclosure’s internal temperature.
4
Be sure that heat from surrounding equipment does not cause the XBT GT to
exceed its standard operating temperature.
5
When installing the XBT GT in a slanted panel, the panel face should not incline
more than 30°.
30° or less
76
6
When installing the XBT GT in a slanted panel, and the panel face inclines more
than 30°, the ambient temperature must not exceed 40 °C. You may need to use
forced air cooling (fan, A/C) to ensure the ambient operating temperature is 40°C
or below.
7
When installing the XBT GT vertically, position the unit so that the Power Input
Terminal Block is also vertical.
8
When installing the XBT GT in Enclosure type 4 compliant environment, use only
the screw installation fasteners supplied with the XBT GT (installation brackets +
attachment screws).
35010372 01 12/2005
Installation and Wiring
Stage
9
Fasteners’
Instructions
35010372 01 12/2005
Description
For easier maintenance, operation and improved ventilation, install the XBT GT at
least 100mm [3.94 in.] away from adjacent structures and other equipment as
shown in the following illustrational:
The following table describes the Fasteners’ instructions to be taken:
Stage
Description
1
The minimum number of installation fasteners required to install a XBT GT unit is
four (4) for Screw Installation Fastener’s system.
2
The minimum number of installation fastener’s required to install XBT GT unit is
two (2) for Spring Clip system.
77
Installation and Wiring
Spring Clips’
Procedure
The following table describes how to install the XBT GT with Spring Clip:
Step
Action
1
Place the XBT GT on a level surface with the display panel facing downward.
2
Check that the XBT GT’s installation gasket (See Regular Cleaning) is seated
securely into the gasket’s groove, which runs around the perimeter of the panel’s
frame.
3
Create the correct sized opening required to install the XBT GT, using the
installation dimensions (See Panel cut-out dimensions) given.
4
Insert the XBT GT (example: XBT GT1100/1130) into the panel cut-out:.
A
Under 4C
B
XBT GT
5
Adjust the Spring Clips for the panel thickness:
z 1.6 mm ≤ panel thickness ≤ 4 mm (position 1),
z 4 mm ≤ panel thickness ≤ 6 mm (position 2).
Position 1
Position 2
6
78
Place the Spring Clips at the anchoring points:
35010372 01 12/2005
Installation and Wiring
Step
7
8
Action
Lock the Spring Clips by pressing simultaneously on the top and the bottom with two
fingers.
To remove the Spring Clips:
z Unlock the Spring Clips by pressing on the back:
CAUTION
RISK OF LOSS OF SEAL
The gasket helps maintain the protection ratings (IP65, IP20) of the unit, and
provides additional protection from vibration. It is strongly recommended that you
use the installation gasket, since it absorbs vibration in addition to repelling water.
Install the gaskets delivered with your XBT GT product.
Failure to follow this instruction can result in injury or equipment damage.
35010372 01 12/2005
79
Installation and Wiring
Installation with
screw fasteners
The following table describes how to install the XBT GT with screw fasteners:
Step
Action
1
Place the XBT GT on a level surface with the display panel facing downward.
2
Check that the XBT GT’s installation gasket (See Regular Cleaning) is seated
securely into the gasket’s groove, which runs around the perimeter of the panel’s
frame.
3
Create the correct sized opening required to install the XBT GT, using the
installation dimensions (See Panel cut dimensions) given.
4
Insert the XBT GT (example: XBT GT1100/1130) into the panel cut:
Under 4-
A
C
B
XBT GT
5
Insert the installation fasteners into the XBT GT ‘s insertion slots situated on the left
and right side of the unit and they are made to slide to a back side. If the fasteners
are not correctly attached, the XBT GT unit may shift or fall out of the panel:
Installation
Panel
Slot
6
80
Hook
Be sure to insert installation fasteners in the recessed portion of an installation
fastener’s hole:
35010372 01 12/2005
Installation and Wiring
Step
7
Action
Use a Phillips screwdriver to tighten each fastener screw and secure the XBT GT in
place. The necessary torque is 0.5 Nm (4.4 lb-in):
CAUTION
RISK OF LOSS OF SEAL
The gasket helps maintain the protection ratings (IP65, IP20) of the unit, and
provides additional protection from vibration. It is strongly recommended that you
use the installation gasket, since it absorbs vibration in addition to repelling water.
Install the gaskets delivered with your XBT GT product.
Failure to follow this instruction can result in injury or equipment damage.
Note: The Screw Installation Fasteners are required for NEMA4 protection.
35010372 01 12/2005
81
Installation and Wiring
4.2
Wiring Precautions
At a glance
Overview
This section presents principle of XBT GT wiring.
What's in this
Section?
This section contains the following topics:
82
Topic
Page
Connecting the Power Cord
83
Connecting the Power Supply
86
Grounding
88
Input/Output Line placement
90
35010372 01 12/2005
Installation and Wiring
Connecting the Power Cord
Introduction
Follow these instructions when supplying power to the XBT GT unit.
Note:
z When the Frame Ground terminal is connected, be sure the wire is grounded.
Not grounding the XBT GT unit will result in excessive noise and vibration.
Grounding is required to assure EMC level immunity.
z The Shield Ground (SG) and Frame Ground (FG) terminals are connected
internally in the XBT GT unit.
z If your system is installed with the 24 VDC power connected to the Frame
Ground (typical in systems such as fire protection), when connecting other
devices, be sure the design of the overall system does not produce a short loop.
WARNING
RISK OF ELECTRIC SHOCK
z
z
z
z
Be sure the power cord is unplugged from the power outlet when connecting the
power terminals to the XBT GT unit .
The XBT GT1000 series and the XBT GT2000 series use only 24V DC power.
Using any other level of power can damage both the power supply and the
XBT GT unit.
Since the XBT GT is not equipped with a power switch, be sure to connect a
power switch to the XBT GT’s power supply.
Be sure to ground the XBT GT's FG terminal. Failure to do so can lead to an
electrical shock or XBT GT malfunction.
Failure to follow this instruction can result in death, serious injury, or
equipment damage.
35010372 01 12/2005
83
Installation and Wiring
Power Cord
Preparation
Note:
z Wherever possible, use wires that are 0.2 to 2.5 mm2 (24 - 12 AWG) in size for
the power cord, and twist the wire ends before attaching the terminals.
z If the conductor’s end (individual) wires are not twisted correctly, the end wires
may either short loop to each other, or against an electrode. To avoid it, use
D25CE/AZ5CE cable-ends.
z The Conductor Type is solid or stranded wire.
The following illustration shows the conductor length:
Power Plug
Illustration
The following illustration shows the Power Plug
Insertion
Direction
The following table displays connection wires into the Power Plug:
84
Connection
Wire
+
24V
-
0V
FG
Grounded Terminal connected to the XBT GT chassis.
35010372 01 12/2005
Installation and Wiring
How to connect
the Power Cord
on XBT GT1100/
1130
The following table explains how to connect the Power Plug:
Step
Action
1
Remove the Power Cord from the Power supply.
2
Remove the Power Plug from XBT GT.
3
Remove the vinyl cover of each of the Power Cord’s wires.
4
Twist the wire ends.
5
Connect the wires to the Power Plug by using flat-blade screwdriver (Size 0.6 X 3.5)
6
Torque the mounting screws: 0.5 to 0.6 Nm (4.4 to 5.2 lb-in)
7
Replace the Power Plug to the Power Connector.
Note:
z Don’t solder the wire directly to the power receptable pin.
z The power supply cord should be equivalent to the specification shown above.
Be sure to twist the power cords together, up to the power plug, for EMC
cancellation. (See illustration as shown below)
Example of
Power Cord’s
illustration
connection on
XBT GT1100/
1130
The following illustration displays a connection’s example of the Power Cord on
XBT GT1100/1130:
Terminal block
wire set block
Power Plug
FG
35010372 01 12/2005
85
Installation and Wiring
Connecting the Power Supply
Introduction
Follow these instructions when supplying power to the XBT GT unit.
Precautions
z
z
z
z
z
z
Connect the power cord to the Power Connector on the side of the XBT GT unit
using the Power Plug.
Between the line and the ground, be sure to use a regulated power supply with a
Class 2 Power Supply
To increase the noise resistance, be sure to twist the ends of the power cord
wires before connecting them to the Power Plug.
The XBT GT unit’s power supply cord should not be bundled with or kept close to
main circuit lines (high voltage, high current), or input/output signal lines.
Connect a lightning surge absorber to handle power surges.
To reduce noise, make the power cord as short as possible.
WARNING
RISK OF EQUIPMENT DAMAGE AND POWER LOSS
z
z
z
z
Avoid excessive stress on the power cable to prevent accidental disconnection.
Securely attach power cables to the panel or cabinet.
Use the designated torque to tighten the unit’s terminal block screws.
Install and fasten unit on installation panel or cabinet prior to connecting Power
Supply and Communication lines.
Excessive stress on the power connection or attempting to install a unit with the
power cables connected may disconnect or cause damage to the power
connections, which can cause short circuits, fire or incorrect operation.
Failure to follow this instruction can result in death, serious injury, or
equipment damage.
86
35010372 01 12/2005
Installation and Wiring
Diagram of the
Power Supply
Connections
The following displays the Power Supply Connections:
XBT GT Unit
Main
Power
XBT GT
Power
I/O Unit
I/O
Power
XBT GT Unit
Main
Power
XBT GT
Power
I/O Power
I/O
Power
I/O Power
Operation unit
Motor
Main
Circuit
Note:
z Be sure to ground the surge absorber (E1) separately from the XBT GT unit (E2).
z Select a surge absorber that has a maximum circuit voltage greater than that of the
peak voltage of the power supply.
The following displays the Lightning Surge Absorber connection:
XBT GT Unit
FG
E1
35010372 01 12/2005
E2
87
Installation and Wiring
Grounding
Introduction
Take the following precautions for grounding the XBT GT unit.
WARNING
RISK OF EQUIPMENT DAMAGE AND UNINTENDED EQUIPMENT
OPERATION
Do not use common grounding, since it can lead to electrostatic damage and
unintended equipment operation which may lead to an accident or machine
breakdown.
Failure to follow this instruction can result in death, serious injury, or
equipment damage.
Exclusive
Grounding
Connect the FG terminal found at the Power Plug to an exclusive ground.
XBT GT Unit
88
Other
Equipment
35010372 01 12/2005
Installation and Wiring
Common
Grounding
If exclusive grounding is not possible, use a common connection point.
The grounding is OK
XBT GT Unit
Other
Equipment
The grounding is not OK
XBT GT Unit
Procedure
Other
Equipment
When Grounding, make sure to follow the procedures given below.
Step
Action
1
Check that the grounding resistance is less than 100Ω. (1).
2
The SG and FG terminals are connected internally in the XBT GT unit.
3
When connecting the SG line to another device, be sure that the design of the
system/connection does not produce a grounding loop.
4
The grounding wire should have a cross sectional area greater than 2mm (1). Create
the connection point as close to the XBT GT unit as possible, and make the wire as
short, as possible. When using a long grounding wire, replace the thin wire with a
thicker wire, and place it in a duct.
5
If the equipment does not function properly when grounded, disconnect the ground
wire from the FG terminal.
(1): Observe local codes and standards. Ensure the ground connection has a resistance
of
less than 100Ω. and that the ground wire has a cross-section of at least 2mm2 or 14AWG.
For details, contact your local Schneider Electric distributor.
35010372 01 12/2005
89
Installation and Wiring
Input/Output Line placement
Introduction
Input and output signal lines must be separated from the power supply cables for
operating circuits.
If this is not possible, use a shielded cable and connect the shield to the XBT GT’s
FG terminal.
90
35010372 01 12/2005
Installation and Wiring
4.3
Tool Port Connector
At a Glance
Overview
This section describes the Tool Port Connector Installation.
What's in this
Section?
This section contains the following topics:
35010372 01 12/2005
Topic
Page
Presentation
92
USB Data Transfer Cable (XBT ZG925) - USB Driver Installation
93
91
Installation and Wiring
Presentation
Introduction
The Data Transfer Cables (XBTZG915 and XBTZG925). See. Parts Identification
and Functions, p. 54 can be attached to the Tool Port on XBT GT11** Series units
to allow transferring of data from the computer to the XBT GT
WARNING
RISK OF ELECTRIC SHOCK
To prevent an electric shock, unplug the XBT GT unit’s Power Cord from the Main
Power Supply prior to attaching or detaching any connector(s) to or from the XBT GT.
Failure to follow this instruction can result in death, serious injury, or
equipment damage.
Tool Port
Connector
Location
The following diagram shows the Tool Port Connector Location.
XBT GT Unit
Tool Port Connector Location
Rear face of:
XBT GT1100
XBT GT1130
Tool
Connector
92
35010372 01 12/2005
Installation and Wiring
USB Data Transfer Cable (XBT ZG925) - USB Driver Installation
Introduction
The USB Data Transfer Cable is used to download data from a PC running VijeoDesigner to the XBT GT unit. It connects to the Tool Port of the XBT GT.
Installation
Requirements
The PC must run on Microsoft Windows 2000 or Windows XP.
You will need the installation CD for Vijeo-Designer.
CAUTION
RISK OF EQUIPMENT DAMAGE
Follow the procedure described below to prevent damage to the cable connector
or the XTG GT.
z When connecting the USB Data Transfer Cable to the PC or to the XBT GT unit,
insert the cable’s connector at the correct 90° angle.
z
When disconnecting the cable, make sure to hold the connector, not the cable itself.
z
If the cable is unplugged from the port designated during installation and connected
to a different port, the Operating System (OS) will not recognize the new port.
Therefore, make sure to always use the port designated during installation.
z
If the installation does not complete successfully, restart the PC and quit all
resident applications before re-installing the software.
Failure to follow this instruction can result in injury or equipment damage.
35010372 01 12/2005
93
Installation and Wiring
Installation
Procedure for
Window 2000
Installation
Procedure for
Windows XP
94
Use the following procedures with Windows 2000:
Step
Action
1
Start Windows, and connect the XBTZG925 cable to your PC’s USB port at one
end, and to the XBT GT’s tool port at the other end.
2
Insert the Vijeo-Designer CD into the CD-ROM drive.
3
The New Hardware Wizard dialog box appears. Click Next.
4
In the following dialog box, select Search for a suitable driver for my device
[recommended] option, and click Next.
5
In the following dialog box, select Specify a location option, and click Next.
6
In the following dialog box, Click Browse then, select the Set2pl.inf file located in
the CD-ROM’s folder XBTZG925, and click Open.
7
The dialog box displays the driver for the XBTZG925. Click OK.
8
Confirm the wizard finds the driver for the following device: Telemecanique
XBTZG925, and click Next.
9
Click Finish to complete the installation.
Use the following procedures with Windows XP:
Step
Action
1
Start Windows, and connect the XBTZG925 cable to your PC’s USB port at one
end, and to the XBT GT’s tool port at the other end.
2
Insert the Vijeo-Designer CD into the CD-ROM drive.
3
The Found New Hardware Wizard dialog box appears. Select Install from a list or
specific location (Advanced) and click Next.
4
In the following dialog box, select Include this location in the search, and click
Browse.
5
From the Installation CD-ROM, select the XBTZG925 folder, and click OK.
6
In the Found New Hardware Wizard dialog box, click Next.
7
The name of the Telemecanique XBTZG925 driver now displays in the dialog box.
Click Continue Anyway.
8
Click Finish in the following screen to complete the installation.
35010372 01 12/2005
Installation and Wiring
Post-Installation
Check
Changing the
COM Port
Number
Execute the following check after installation:
Step
1
In the Control Panel, click on System Properties and select Device Manager.
2
Confirm that Telemecanique XBTZG925 COM3 is listed below Ports [COM & LPT].
The COM number 3 is assigned automatically by the operating system (OS). If the
OS had previously allocated COM 3 or other numbers for devices such as Internal
modems, IrDA ports, and so on, XBTZG925 is allocated to the next available COM
number. However if required, you can change the COM port number.
Step
Troubleshooting
Action
Action
1
In the Control Panel, click on System Properties and select Device Manager.
2
Click to expand the Ports [COM & LPT] folder, right-click the Telemecanique
XBTZG925 COM 3 node, and then click Properties.
3
In the Telemecanique XBTZG925 [COM3] Properties dialog box, click the Port
Settings tab, and click the Advanced button.
4
At the bottom of the Advanced Settings for COM 3 dialog box, select an unused
number and click OK.
5
When the following Communication Port Properties dialog box appears, click Yes.
The following table describe errors that may occur and their possible solutions:
Problem/Symptom
Solution
The USB cable is not recognized.
Connect the cable correctly, or restart you
PC. Also, when connecting a USB hub, make
sure to connect it directly to your PC’s USB
The Plug and Play is not functioning correctly.
port.
You are unable to use the USB cable after
connecting it to a USB hub.
The power supplied from the hub may be
insufficient. Make sure the hub is selfpowered.
Connect the cable directly to the PC USB
port.
After installation, a "?" is displayed when you The driver has not been installed correctly.
try to confirm the cable’s status via the Device Unionist the driver and re-install it.
Manager.
Uninstalling the
USB Driver
35010372 01 12/2005
Unplug the USB Data Transfer Cable from the PC and double-click on the CD-ROM’s
DRemover2K.exe file to start the uninstallation process.
95
Installation and Wiring
4.4
Ethernet Cable Connector
Presentation
Introduction
The XBT GT1130/2130/2330 come equipped with an IEEE802.3 compliant Ethernet
Interface, that transmits data at 10Mbps or 100 Mbps.
Illustration of
XBT GT Ethernet
Cable Connector
The following illustration displays the location of the RJ45 Ethernet Cable
Connector:
Ethernet Cable Connector
XBT GT1130 Bottom
Ethernet Cable Connector
XBT GT2130/2330
Right Side
Both the Ethernet connector and the COM1 serial connector on XBT GT1130 or
COM2 serial port connector on XBT GT2130/2330 use RJ45 ports, therefore, DO
NOT confuse them.
96
35010372 01 12/2005
Installation and Wiring
WARNING
RISK OF MATERIAL DAMAGE AND UNINTENDED EQUIPMENT
OPERATION
z
z
z
Do not connect the serial cable to the Ethernet port.
Do not connect the Ethernet cable to the serial port.
Carefully observe the product markings distinguishing between the Ethernet
and serial ports.
Since Ethernet Port and the serial port (RJ45) share the same type of plug, there
is a risk of swapping the Ethernet line with the serial line. Improper connections
may result in damage to the XBT GT, to remotely connected equipment, and may
cause unintended equipment operation.
Failure to follow this instruction can result in death, serious injury, or
equipment damage.
Note: It is recommended that your Ethernet network is installed by a trained and
qualified person.
You may be able to use the 1:1 connection with a cross cable depending on the connected
PCs and network cards. Make sure to use 1:1 connections with a hub or a switch.
35010372 01 12/2005
97
Installation and Wiring
4.5
CF Card
CF Card Installation and Removal
Introduction
The following XBT GT target machines support the use of CF cards.
z
z
z
z
Precautions
XBT GT2120
XBT GT2130
XBT GT2220
XBT GT2330
When using the XBT GT Unit and a CF Card, follow the precautions below:
z
z
z
z
z
z
Prior to inserting or removing a CF Card, be sure to turn the XBT GT unit’s CF
Card ACCESS switch OFF and to confirm that the ACCESS lamp is not lit. If you
do not, CF Card internal data may be damaged or lost.
Check that the CF Card DIP Switches setting are appropriate.
While a CF Card is being accessed, NEVER turn OFF or reset the XBT GT, or
insert or remove the CF Card. Prior to performing these operations, create and
use a special XBT GT application screen that will prevent access to the CF Card.
Prior to inserting a CF Card, familiarize yourself with the CF Card’s front and rear
face orientation, as well as the CF Card connector’s position. If the CF Card is not
correctly positioned when it is inserted into the Mulit Unit, the CF Card’s internal
data and the XBT GT unit may be damaged or broken.
Be sure to use only CF Cards manufactured by Schneider Electric. XBT GT unit
performance cannot be guaranteed when using another manufacturer’s CF Card.
Once XBT GT data is lost, it cannot be recovered. Since accidental data loss can
occur at any time, be sure to back up all XBT GT screen and CF Card data regularly.
CAUTION
RISK OF EQUIPMENT DAMAGE
Be sure to follow the instructions given below to prevent the CF Card’s internal
data from being destroyed or a CF Card malfunction from occurring:
z DO NOT bend the CF Card.
z DO NOT drop or strike the CF Card against another object.
z Keep the CF Card dry.
z DO NOT touch the CF Card connectors.
z DO NOT disassemble or modify the CF Card.
Failure to follow this instruction can result in injury or equipment damage.
98
35010372 01 12/2005
Installation and Wiring
Inserting the CF
Card
Use the following steps to insert the CF Card in the XBT GT2000 unit (except
XBT GT2110).
Step
35010372 01 12/2005
Action
1
Slide the CF Card Cover in the direction shown here, then upwards to open the
cover.
2
Insert the CF Card in the CF Card Slot, until the ejector button is pushed forward.
3
Close the cover. (As shown).
4
Confirm that the CF Card Access LED turns ON.
You cannot access to the CF Card with the CF Card cover opened. However, if the CF
Card is being accessed, the access will be continued even if you open it on the way.
99
Installation and Wiring
Removing the CF
Card
Simply reverse the steps shown in the previous "inserting CF Card" explanation.
Prior to removing the CF Card, confirm that the CF Card Access LED is turned OFF.
The following figure displays how to remove the CF Card:
Eject Button
CF Card
Handling
The CF card has a life expectancy of 100,000 write cycles. Therefore, be sure to
back up all CF Card data regularly to another storage media. (100,000 times
assumes the overwriting of 500 kilobytes of data in DOS format).
The following table presents two methods to back up data.
If
Then
And
Your PC is
equipped with a
PC Card Slot
To view CF Card data on a personal
computer, first, insert the CF Card into
a CF Card Adaptor XBTZGADT.
Save data CF Card on the PC.
Your PC is not
equipped with a
PC Card Slot
Use a standard XBTZGADT type PC
Card or CF Card reader.
Save data CF Card on the PC.
Note: Depending on the setup of your PC, it’s possible that the Card reader may
not operate correctly.
The connection between a personal computer and CF Card reader has been tested
using an Windows® compatible machine. Check that CF Card reader is correctly
installed and configured. Please contact your PC or CF Card reader manufacturer
directly for details.
100
35010372 01 12/2005
Installation and Wiring
4.6
USB Port
At a Glance
Overview
This section presents the USB Port.
What's in this
Section?
This section contains the following topics:
35010372 01 12/2005
Topic
Page
Presentation
102
USB Data Transfer Cable (XBT ZG935) - USB Driver Installation
103
USB Cable Clamp
106
101
Installation and Wiring
Presentation
Introduction
The following XBT GT units have a USB port:
z
z
z
z
z
XBT GT2110
XBT GT2120
XBT GT2130
XBT GT2220
XBT GT2330
Data transfer cable (XBT ZG935) can be attached to the USB port to allow
transferring of data from the computer to the XBT GT.
WARNING
RISK OF ELECTRIC SHOCK
To prevent an electric shock, unplug the XBT GT unit’s Power Cord from the Main
Power Supply prior to attaching or detaching any connector(s) to or from the XBT GT.
Failure to follow this instruction can result in death, serious injury, or
equipment damage.
102
35010372 01 12/2005
Installation and Wiring
USB Data Transfer Cable (XBT ZG935) - USB Driver Installation
Important
information
CAUTION
RISK OF EQUIPMENT DAMAGE
Follow the procedure described below to prevent damage to the cable connector
or the XTG GT.
z When connecting the USB Data Transfer Cable to the PC or to the XBT GT unit,
insert the cable’s connector at the correct 90° angle.
z
When disconnecting the cable, make sure to hold the connector, not the cable itself.
z
If the cable is unplugged from the port designated during installation and connected
to a different port, the Operating System (OS) will not recognize the new port.
Therefore, make sure to always use the port designated during installation.
z
If the installation does not complete successfully, restart the PC and quit all
resident applications before re-installing the software.
Failure to follow this instruction can result in injury or equipment damage.
35010372 01 12/2005
103
Installation and Wiring
Installation
Procedure for
Windows 2000
104
Use the following procedure with Windows 2000:
Step
Action
1
Insert the Vijeo Designer Installation CD-ROM into your CD-ROM drive. If the
installation menu comes up, click Exit to close the menu.
2
Connect the USB cable to the USB port on your PC.
3
When Windows detects the USB cable and displays the Found New Hardware
Wizard, click Next.
4
Select Search for a suitable driver for my device, then click Next.
5
Select the Specify a location check box, then click Next.
6
Define the path and filename Z:\XBT ZG935\usbdlc.inf (Z is the drive letter of the
CD-ROM drive) and click OK.
7
Make sure the hardware wizard has located the correct driver for the USB Link
Cable (XBT ZG935) and click Next.
8
Once driver installation is complete, click Finish to exist the wizard, then take a
following steps to make sure installation is successful.
1. On the PC, make sure the USB cable is physically connected to the USB port.
2. On the desktop, right-click My Computer and click Properties.
3. In the System Properties dialog box, select the Hardware tab, and then click
Device Manager.
4. In the Device Manager, the USB Link Cable (XBT ZG935) should display below
the USB (Universal Serial Bus) controller.
9
Note: You can install the USB Link Cable Driver from the Installer menu: Click the
USB Driver button and follow the instructions.
35010372 01 12/2005
Installation and Wiring
Installation
Procedure for
Windows XP
Troubleshooting
Use the following procedure with Windows XP:
Step
Action
1
Insert the Vijeo Designer Installation CD-ROM into your CD-ROM drive. If the
installation menu comes up, click Exit to close the menu.
2
Connect the USB cable to the USB port on your PC.
3
When Windows detects the USB cable and displays the Found New Hardware
Wizard, select Install from a list or specific location, then click Next.
4
Select the Search for the best driver in these location and select the Include this
location in the search check box, then define the path:Z:\XBT ZG935\usbdlc.inf (Z is
the drive letter of the CD-ROM drive) and click Next.
5
Click Next on the [New hardware detect wizard] dialog box.
6
Make sure the hardware wizard has located the correct driver for the USB Link Cable
(XBT ZG935), then click Continue.
7
Note: You can install the USB Link Cable Driver from the Installer menu: Click the
USB Driver button and follow the instructions.
The following table describe errors that may occur and their possible solutions:
Problem/Symptom
Solution
The USB cable is not recognized.
Connect the cable correctly, or restart you PC.
Also, when connecting a USB hub, make sure to
connect it directly to your PC’s USB port.
Overcurrent occurred
The Plug and Play is not functioning correctly.
You are unable to use the USB cable after
connecting it to a USB hub.
The power supplied from the hub may be
insufficient. Make sure the hub is self-powered.
Connect the cable directly to the PC USB port.
After installation, a "?" is displayed when you try to The driver has not been installed correctly.
confirm the cable’s status via the Device Manager. Unionist the driver and re-install it.
Uninstalling the
USB Driver
35010372 01 12/2005
Step Action
1
Click the USB device icon "Stop USB link cable" in the Windows task tray and then
click the command Stop USB Link Cable (XBT ZG935) for Windows 2000, or Safely
remove USB Link Cable (XBT ZG935) for Windows XP.
2
When the Safe To Remove Hardware massage box appears, remove the USB
download cable.
3
Click OK to close the message box.
105
Installation and Wiring
USB Cable Clamp
Attaching the
USB Cable
Clamp
Use the following procedures to attach the USB Cable Clamp:
Step
Action
1
Insert the USB holder into the slot in front of the XBT GT unit’s USB port and pull it
down and forward.
2
Pass the band of the USB cable clamp through the bridge of the USB holder.
Bridge
USB Holder
106
35010372 01 12/2005
Installation and Wiring
Step
3
Action
Insert the USB cable into the port. Fasten the band around the plug and secure it
with the clamp.
Clamp
USB Holder
USB Cable
Release the USB
Cable Clamp
Lower the tab and lift the clamp to release the plug as the following illustration:
Tab
Clamp
35010372 01 12/2005
107
Installation and Wiring
108
35010372 01 12/2005
Setting and Debugging
II
At a Glance
Overview
This part describes the settings available on the target machine as well as how to
debug XBT GT unit.
What's in this
Part?
This part contains the following chapters:
35010372 01 12/2005
Chapter
Chapter Name
Page
5
Settings
111
6
Troubleshooting
121
7
Maintenance
129
109
Setting and Debugging
110
35010372 01 12/2005
Settings
5
At a Glance
Overview
This chapter presents the Settings to be configured on XBT GT unit.
What's in this
Chapter?
This chapter contains the following sections:
Section
5.1
35010372 01 12/2005
Topic
XBT GT Settings
Page
113
111
Settings
112
35010372 01 12/2005
Settings
5.1
XBT GT Settings
At a Glance
Overview
This section describes the settings on all XBT GT units.
What's in this
Section?
This section contains the following topics:
35010372 01 12/2005
Topic
Page
Types of Settings
114
Offline Settings
115
System Settings
118
113
Settings
Types of Settings
Introduction
You can use the Setting menu to configure the XBT GT unit.
Depending on how you use your XBT GT, you can display the Settings menu using
three different methods:
z
z
z
Use a switch,
Touch the top-left corner of the panel when powering up,
Touch three corners of the panel simultaneously while the application is running.
You can select which methods your application uses in the Vijeo-Designer editor’s
Target properties.
To call up Setting
menu
the following table describes the steps in calling up the Setting menu:
Step
1
Action
Set up the method for entering the Setting menu in the editor. You can set up any
combination of the following methods for displaying the Setting menu.
z Switch: create a switch and add the Configuration System Operation.
z Top-Left Corner: in the Target properties, set To Configuration to either Top Left
Corner or Top Left/3 Corner.
z Touch three corners simultaneously: in the Target properties, set To
Configuration to either 3 Corner or Top Left/3 Corner.
If you set To Configuration to None, and do not create a switch to display the Settings
menu, then there would be no way of configuring the XBT GT unit at run time.
114
2
Connect the XBT GT unit’s power supply.
3
Depending on what you set up in Step 1, you can display the Settings menu using
one of the following methods:
z Touch the switch set up with the Configuration system operation.
z Touch the top-left corner of the screen within ten seconds after the XBT GT unit
begins starting up.
z Touch any three corners of the panel simultaneously. Vijeo-Designer Runtime
restarts and displays the Settings menu.
4
The Settings menu contains two tabs: Offline and System. Click either tab to display
its settings.
35010372 01 12/2005
Settings
Offline Settings
Introduction
The Offline settings cannot be changed while a user application is running.
Offline Tab
The following illustration shows the Offline tab on XBT GT1000 unit:
Offline
System
Network
Option
Buzzer
Backlight
Self Test
To Run Mode
The following illustration shows the Offline tab on XBT GT2000 unit:
Offline
Network
System
Buzzer
Backlight
Self Test
Option
To Run Mode
35010372 01 12/2005
115
Settings
Network Settings
The following table describes how to change the network settings (IP address) on
the XBT GT 1300 unit (except on XBT GT1100).
Step
Action
1
In the Settings menu, touch the Offline tab.
2
Touch the Network icon.
3
Touch any of the three fields (IP Address, Subnet Mask, or Default Gateway) and
a keypad will appear.
4
Enter the desired network addresses.
Note: In order for changes to the network settings to take effect, the XBT GT will
restart when you touch "To Run Mode" and return to the application.
Touch Buzzer
The following table describes how to change the buzzer settings on the XBT GT unit.
Step
116
Action
1
In the Settings menu, touch the Offline tab.
2
Touch the Buzzer icon.
3
Touch the desired buzzer mode. The factory setting is When Press Touch object.
z None: Selecting this will turn the buzzer OFF.
z When Press Touch Object: The buzzer will only sound when a Touch Object is
touched.
35010372 01 12/2005
Settings
Backlight
Control
The following table describes how to change the backlight settings on the XBT GT
unit.
Step
Action
1
In the Settings menu, touch the Offline tab.
2
Touch the Backlight icon.
3
In the Backlight Control, define the backlight operations.
z Wait: To extend the life of the backlight, you can set up the XBT GT so that it
turns off the backlight when the panel is inactive (idle) for the defined period of
time, (Idle means the XBT GT panel has not been touched). The factory setting
for this item is OFF.
z Enable Touch if Backlight is Burned Out: this setting defines whether the touch
panel is enabled or disabled when a backlight burnout is detected. When this
feature is cleared and the backlight burns out, touch inputs are ignored to prevent
operation errors. the factory setting for this item is OFF.
4
To turn the backlight off automatically after a specified period of time, touch the Wait
checkbox and then set the idle time.
Self Test
Runs test on the XBT GT unit to ensure its various hardware components are
operating correctly.
Option
Configure the COM1 port as a power supply.
35010372 01 12/2005
117
Settings
System Settings
Introduction
You can change System Settings while the user application is still running.
System tab
The following illustration displays System tab on XBT GT1000 unit:
Offline
System
Stylus
Ver. Info
Date/Time
Memory
Restart
Brightness
Language
Option
To Run Mode
The following illustration displays System tab on XBT GT2000 unit:
Offline
System
Stylus
Date/Time
Restart
Ver. Info
Langage
Memory
Brightness
Option
To Run Mode
118
35010372 01 12/2005
Settings
Stylus
This setting is not supported for XBT GT1100/1130 series units.
Date/Time
The following table describes how to change the date or time on the XBT GT unit.
Step
Restart
In the Settings menu, touch the System tab.
2
Touch the Date/Time icon.
3
Touch any of the Date or Time fields and a data entry keypad will display. Use this
keypad to define the selected date or time setting.
The following table describes how to force the XBT GT unit to restart.
Step
Language
In the Settings menu, touch the System tab.
2
Touch the Restart icon.
3
Touch the Restart button to restart the XBT GT unit.
The following table describes how to select the language used by the XBT GT
system (Settings menu and run-time messages) and user application.
Action
1
In the Settings menu, touch the System tab.
2
Touch the Language icon.
3
Touch the spin boxes to select the desired System and User Application
languages.
The languages available in the Language Settings are defined in the VijeoDesigner editor.
The following table describes how to access version information about the runtime
and user application on the XBT GT unit.
Step
35010372 01 12/2005
Action
1
Step
Version
Information
Action
1
Action
1
In the Settings menu, touch the System tab.
2
Touch the Ver.Info icon.
Version Information displays the version number of the runtime and the version
and build number of the editor that was used to design the user application.
119
Settings
Memory
The following table describes how to access information about the amount of
memory available and the amount of memory currently being used.
Step
Brightness/
Contrast Control
Action
1
In the Settings menu, touch the System tab.
2
Touch the Memory icon.
z DRAM describes the amount of memory currently being used by the application.
z Main Flash indicates the amount of internal memory (flash memory) required to
store the runtime system files and the user application.
Step
Action
1
In the Settings menu, touch the System tab.
2
Touch the Brightness icon.
3
Touch the up/down arrows to adjust the brightness and contrast.
Reducing the brightness and contrast could increase the life span of the backlight.
Option
Step
120
Action
1
In the Settings menu, touch the System tab.
2
Touch the Option icon.
3
Select Invert to reverse the black and white colors on the screen.
In some projects and in some environments, inverting could make the application
more visible and reduce eye-strain of operator working with the target machine.
35010372 01 12/2005
Troubleshooting
6
At a Glance
Overview
This chapter describes how to find and resolve problems with the XBT GT unit.
What's in this
Chapter?
This chapter contains the following topics:
35010372 01 12/2005
Topic
Page
Troubleshooting Checklists
122
Self Test List
126
121
Troubleshooting
Troubleshooting Checklists
Introduction
When a problem occurs, make sure to go through the checklist and follow the
instructions given.
Here are the main potential problems which may occur when using the XBT GT unit are:
z
z
z
z
z
Panel display is blank,
Connected equipment cannot be used,
XBT GT does not respond or responds very slowly,
XBT GT beeps when powered on,
Cannot change the date or time.
Note: If the following checklists do not solve your problem, please contact your
local Schneider Electric vendor or the vendor who sold you the XBT GT unit.
Panel display is
blank
The table below gives you some solutions to adopt if the XBT GT unit display is
blank.
Step
122
Check/Operation
Solution
1
Are all Vijeo Designer screens
downloaded to the XBT GT unit?
You may have to download again the
screens again.
2
Is the Initial Panel ID set up correctly in
Vijeo Designer?
Enter the Initial Panel ID in the Vijeo
Designer editor and download again.
3
Is the unit using the correct rated
voltage?
Verify the power supply connections and
levels.
4
Is the power supply OFF or
disconnected?
Follow the instructions in this manual for
reconnecting the power supply.
5
Is the power lamp lit?
A blank power lamp may indicate a
problem with the hardware.
6
Is the backlight lit?
The backlight may be burned out or there
may be a problem with the unit. Contact
your local Schneider Electric distributor,
for backlight replacement.
7
Is the problem resolved?
If none of the previous steps fixed the
blank panel display problem, then there
is a problem with the hardware.
35010372 01 12/2005
Troubleshooting
Connected
equipment
cannot be used
35010372 01 12/2005
The table below presents how to run through the following steps when the XBT GT
unit is failing to communicate with connected equipment.
Step
Check/Operation
Solution
1
Is the power supply OFF or
disconnected?
Verify the power supply connections and
levels.
2
Do the Driver and Equipment settings in
Vijeo-Designer match the actual
equipment you are trying to communicate
with?
In the Vijeo Designer editor’s Navigator
window’s Project tab, expand the I/O
Manager node to enter the correct
configuration settings for the Driver and
Equipment nodes.
3
Is the communication cable connected
correctly?
Refer to the associated protocol manual
for information about cable diagrams.
4
Is the problem resolved?
If none of the previous steps fixed the
communication problem, then there is a
problem with the hardware.
123
Troubleshooting
XBT GT does not
respond when
touched
Step
The table below gives you some solutions to adopt if the XBT GT unit is either not
responding when touched or if its response time is very slow.
Check/Operation
Solution
1
Disconnect all the cables except the
power cable.
-
2
If the test fails, there is a problem with the hardware.
Enter the Settings menu, touch the
Offline tab and then touch the Self Test
icon.
Run the Touch Panel test.
3
Enter the Settings menu, touch the
System Tab and then touch the Stylus
icon. Calibrate the analog touch.
If the touch calibration is not possible, there is a problem with the
hardware.
4
If touch response is slow, does it
happen on a specific panel?
If the panel displays the values of a large number of equipment
variables, you may want to redesign the panel and separate the
variables into different panels and download again.
5
To resolve this problem, try each of the following in the Vijeo
If touch response is slow, the target’s
CPU may be very busy communicating Designer editor and download again.
with external equipment.
z If you are using serial communication, make sure the
communication speed between the target and equipment is
optimized.
z In the equipment or scan group properties, reduce the Scan
Rate to Slow. This will reduce the frequency of variable updates
to 1000ms.
z If you use many equipment variables in application scripts, you
may want to change the script to a panel script so that the
variables are active only when the information is necessary.
If none of the above works, then you may have to reduce the
number of external variables in the project.
If none of the proposed options work, contact your Schneider
Electric Technical Support for other methods of optimizing your
project.
124
35010372 01 12/2005
Troubleshooting
Target beeps
when powered
ON
If the target beeps continually when you turn ON the power supply, then the system
files on the XBT GT unit have become corrupted.
Cannot change
the Date or Time
The following table gives you some solutions to adopt if you cannot change the date
or time.
To resolve this problem, do the following: From the Vijeo Designer Start menu, use
the Runtime Installer application and run Recovery on the target machine.
Problem
Solution
To ensure that the backup battery is fully
The date and time keeps reverting to a
charged:
different date and time when you try to
change the date or time. The lithium backup z Run the XBT GT unit continuously for 24
battery for the internal clock has probably run
hours, (the battery need 96 hours to be
out of power.
recharged fully).
z Try to change the clock setting again.
If the error continues, the battery may need
replacement.
Contact your local Schneider Electric
distributor for service.
WARNING
RISK OF BATTERY EXPLOSION
Do not attempt to replace the XBT GT battery. Incorrectly replacing the battery
may result in the battery explosion next time it is used.
Contact a Schneider Electric representative for the nearest Schneider Electric
support center.
Failure to follow this instruction can result in death, serious injury, or
equipment damage.
Note: The lifetime of the backup battery depends on the ambient temperature.
The expected battery life is 10+ years when:
z The battery ambient temperature is less than 40°C (104°F).
z Or the unit ambient temperature is less than 25°C (77°F).
35010372 01 12/2005
125
Troubleshooting
Self Test List
Introduction
The XBT GT unit is equipped with a number of diagnostic features that can be used
to check its system and interfaces for any problems.
Self Test
From the Settings menu, touch the Offline tab and then the Self Test icon. Self Test
menu appears.
The following illustration shows the Self Test menu on XBT GT1000.
Self Test
Char. Pattern
COM 2
Disp. Pattern
Video Memory
Touch Panel
COM 1
Return
The following illustration shows the Self Test menu on XBT GT2000.
Self Test
Char. Pattern
Video Memory
Disp. Pattern
Touch Panel
COM 1
COM 2
Return
126
35010372 01 12/2005
Troubleshooting
Details
The following table describes each test in the Self Test menu.
Test
Description
Char. Pattern
Checks the characters in each font set available on the XBT GT unit. Use
this test when characters (usually 2-byte characters) do not display properly.
OK appears if there is no error; NG appears if there is an error.
Disp. Pattern
Use this test when your drawings do not display properly.
Touch Panel
Tests the touch panel cells. Each cell highlights when it’s pressed during the
test.
COM 1
Checks to make sure the serial port (RS-232C and RS-485) is working
properly.
To run the check, you may need to connect a loopback cable (see below).
OK appears if there is no error; an error message appears if there is an error.
COM 2
Video Memory Use this check to test the video memory (memory used for screen display).
Run this test when the screen does not display properly.
OK appears if there is no error; NG appears if there is an error.
35010372 01 12/2005
127
Troubleshooting
Wiring for COM
1, COM 2 tests
When testing the serial port, depending on which port and which communication
format you are testing, you may need to attach a loopback cable with wiring as
defined below.
The following table displays the loopback cable wiring for XBT GT:
RS-232C
RS-422
XBT GT1000 in COM1
Not available.
SD 2
RD 1
XBT GT2000 in COM1
XBT GT2000 in COM1
RD
SD
CS
ER
RI
DR
RS
CD
RDA
SDA
SDB
RDB
CSB
ERB
CSA
ERA
-
128
2
3
8
4
9
6
7
1
1
3
7
2
6
9
8
4
XBT GT2000 in COM2
Not available
35010372 01 12/2005
Maintenance
7
At a Glance
Overview
This chapter explains how to maintain your XBT GT.
What's in this
Chapter?
This chapter contains the following topics:
35010372 01 12/2005
Topic
Page
Regular Cleaning
130
Periodic Check Points
131
Replacing the Backlight
132
129
Maintenance
Regular Cleaning
Introduction
The regular cleaning is composed of:
z
z
Cleaning the
display
Cleaning the front panel,
Cleaning the Gasket and procedures.
When the surface or the frame of the display gets dirty, soak a soft cloth in water
with a neutral detergent, wring the cloth tightly, and wipe the display.
Note:
z Do not use paint thinner, organic solvents, or a strong acid compound to clean
the unit.
z Do not use hard or pointed objects to operate the touch-screen panel, since it
can damage the panel surface.
Cleaning the
Gasket
The gasket protects the XBT GT and improves its water resistance.
Inserting the
Gasket
The gasket must be inserted correctly into the groove for the XBT GT's moisture
resistance to be equivalent to IP65.
A gasket which has been used for a long period of time may have scratches or dirt
on it, and could have lost much of its water resistance. Be sure to change the gasket
at least once a year, or when scratches or dirt become visible.
The upper surface of the gasket should protrude approximately 2mm [0.08 inch] out
from the groove. Be sure to check that the gasket is correctly inserted before
installing the XBT GT into a panel.
Note: Be sure the gasket's seam is not inserted into any of the unit's corners. Insert
the joint only in the straight sections of the groove, preferably in the bottom section.
Inserting it into a corner may lead to its eventually tearing.
130
35010372 01 12/2005
Maintenance
Periodic Check Points
Introduction
To keep your XB GT unit in its best condition, please, check the following points
periodically.
z
z
z
XBT GT1000/
2000 Operation
Environment
z
z
z
XBT GT Operation Environment,
Electrical Specifications,
Related Items.
The operating temperature is within the allowable range (0°C to 50°C) (32°F to
122°F)?
The operating humidity is within the specified range (10%RH to 90%RH), dry bulb
temperature of 39°C (102°F) or less)?
The operating atmosphere is free of corrosive gases?
XBT GT1000/
2000 Electrical
Specifications
z
The input voltage is appropriate?
z XBT GT1000/2000: DC19.2V to DC28.8V.
Related Items
z
Are all power cords and cables connected properly? Have any become loose?
Are all mounting brackets holding the unit securely?
Are there many scratches or traces of dirt on the installation gasket?
z
z
35010372 01 12/2005
131
Maintenance
Replacing the Backlight
Introduction
The XBT GT1000/2000 units’s backlight cannot be replaced by the customer. When
the backlights need to be replaced, please contact your local XBT GT distributor.
WARNING
RISK OF EQUIPMENT DAMAGE AND UNINTENDED EQUIPMENT
OPERATION
Do not create XBT GT touch panel switches for system functions that may cause
injury and/or equipment damage if activated accidentally.
If the XBT GT unit's backlight burns out and the unit is not set to Standby Mode,
the touch panel remains active. If the operator fails to notice that the backlight is
burned out and touches the panel, unintended equipment operation can occur.
Failure to follow this instruction can result in death, serious injury, or
equipment damage.
How to
determine if the
Backlight is
burned out
If your XBT GT unit's backlight suddenly turns OFF, use the following steps to
determine if the backlight is actually burned out:
z
z
132
If the XBT GT unit's "Backlight Control" is not set and the screen has gone blank,
your backlight is burned out.
If the XBT GT unit's "Backlight Control" is set to Standby Mode and the screen
has gone blank, and touching the screen or performing another input operation
does not cause the display to reappear, your backlight is burned out.
35010372 01 12/2005
Index
35010372 01 12/2005
B
AC
133
">