Digital Video Recorder

HD-SDI 4CH

1

Thank you for using our product.

1. This is user's manual for H.264 HD DVR (Digital Video Recorder).

2. This manual contains product specification and introduction, installation guide, operating guide and other necessary matters for easy understanding. Users should read this user's manual carefully for proper use.

3. Contents in this manual may be changed according to the specification change and f t i t ith t tifi ti

4. This user's manual shall never be copied without prior agreement and violating this may be a reason for legal punishment on piracy.

5. If there is any incorrect or insufficient content in this user's manual, notify it to

Customer Support Center.

2

Contents

CH 1. Product Introduction

1-1. Product Contents

1-2. Specifications

1-3. Product Characteristics

1-4. Name of Each Part

CH 2. Installation Guide and Cautions

2-1. Cautions

2-2. Product Installation

2-2-1. Power Connection

CH 3. How to Use

3-1. General Usage Information

3-2. Live Mode d t l

3-2-2. Live mode feature

3-3. Search Mode

3-3-1. Search selection type

3-3-2. Play mode

3-4-1. Display

3-4-2. Record

3-4-3. Device

3-4-4. Network

3-4-5. System

3

CONTENTS

5

6

7

9

11

14

14

20

21

23

28

28

30

31

33

38

42

45

Contents

Trouble Shooting

Warranty

(ULTIMA-X Only)

Appendix B Catcheye for Android mobile

Appendix C Catcheye for iPhone

CONTENTS

48

49

50

52

58

4

CH 1 Product Introduction

CH1. Product Introduction

1-1. Product Contents

After removing packing materials of this product, check whether all following contents are included.

Main Body (DVR):

This converts the analog video and audio signal to the digital signal and saves on HDD.

Adapter:

Power Cable:

This connect the adapter and the power source.

This contains the User’s manual and Client

Program for DVR.

Remote Controller:

This is an IR remote controller for convenience.

Battery:

These are 2(two) battery for the remote controller.

5

CH 1 Product Introduction

1-2. Specifications

Video Input : 720p, 1080i, 1080p

Recording Speed :

720p :1~120fps

1080p : 1~60fps

Compression Method : H.264 Technology

Power : DC12V, 5A (DC adapter)

Power Consumption : 60W

External Terminal : Video Input - BNC 4CH

Video Output - SPOT 1CH, VGA 1CH, HD output 1CH

Audio Input - RCA 4CH

Audio Output - RCA 1CH

Sensor Input - Terminal Block 4CH (NO/NC selectable)

LAN Communication - RJ45 Port

Serial Communication - Terminal Block(RS485)

2xUSB 2.0 Type A

Video and control Transmission - RJ45 Port using xbox

Temperature : 5~40℃(30~110 F)

Humidity : 20%~80%(Non-condensing)

Size : 340 (W) × 250 (D) × 60 (H) mm

Weight : 3Kg(Supplements and Packing Materials Excluded)

Supplements : Adapter 1

Power Cable 1

Program CD 1

Remote Controller 1

Battery 2

6

CH 1 Product Introduction

1-3. Product Characteristics

This DVR can record HD and Full HD video with extreme quality. Also it displays real HD(1920X1080) resolution, and therefore it provides the most clear image quality and the best security level.

2) High reliability

With Embedded hardware and software design, this maintains higher product reliability.

3) Simple usage

This allows users to use it conveniently by placing control buttons similar to existing ones on VCR, and users can easily learn the usage.

4) Pentaplex System

Pentaplex System allows live, recording, backup, networking and playback simultaneously.

5) Selectable recording setup

For recording methods, users can select the frame rate, resolution and video quality individually in order to be appropriate for user's environment.

6) Remote monitoring

With using exclusive line or Internet network, you can search or monitor recorded images remotely by installing exclusive client program on PC.

7) Backup

You can backup with a versitile external USB devices.

8) Audio recording

You can record 4 sound inputs simultaneously. Moreover, you can listen to the sound in search and live monitoring and play mode.

9) V i di th d

This provides convenient use with manual recording, recording by dates and days, hourly schedule recording, sensor and motion detection event recording and others to enable unmanned monitoring.

10) Various total monitoring features

You can cover any security scenario through various sensor inputs and contact output control.

7

CH 1 Product Introduction

11) Display information in easy-to-understand information method

Thi h d i f b di l i i f ti (d t ti di method, recording frame number, HDD capacity and others) in monitoring, recording and playing mode in easy-to-understand way.

12) P/T/Z control

By built in RS485, various P/T/Z cameras can be used.

13) Dual CODEC for video transmission

f (b d ) setup regardless with recording setup.

dl f h l l di d i

14) Web browser support

You can monitor and playback the video and control the PTZ camera by internet explorer.

i

15) Built in S.M.A.R.T.

You can automatically check the health of the hard disk drives.

16) Language pack

Basically DVR has multiple language set, furthermore you can choose the language set if you want.

17) Mirroring by internal HDD

If you install two HDDs, you can use the second HDD for backup for maximum fault tolerance.

18) Spot monitoring

Spot out can be enable to monitor sequentially in other place.

19) Biometric Touch Switch

You can operate with Biometric touch switch in front panel.

8

CH 1 Product Introduction

1-4. Name of Each Part

[Front Panel]

5. NUMBER SELECTION 4. CONTROL WINDOW

2. USB

1. IR WINDOW

3. STATUS RAMPS

1. IR Window : the window for remote controller connect correctly the USB devices and mouse as picture directed.

3. Status lamps

POWER : Blue color back light. Power indicator.

RECORD : Red. Indicate the recording.

NETWORK : Green. Lit on connecting the network

4. CONTROL WINDOW : Going to Menu and Backup Video, Search Video

5. Number Selection : Use for Channel Selection and Number input in Setup Menu

9

CH 1 Product Introduction

[Rear Panel]

9.SENSOR IN

10. AUDIO IN

11.AUDIO

8.RELAY

OUT

7.RS485

13.Xbox

Extender

(option)

1.FAN

2.VIDEO IN

12.HDMI

5. VGA

3. LAN

4.SPOT

6. POWER

1. Cooling Fan

2. Video In: This receives images from SDI cameras.

3. LAN Port: This is the Gigabit Ethernet LAN cable connection terminal.

4. SPOT Out : To CRT 4:3 monitor for spot video.

5. VGA port: video output for analog RGB display

6. DC Power : DC12V 4.0A or up

7. RS485 port : For control the pan and tile cameras. Make sure that the polarity.

8. Relay out : This terminal blocks connect external electric devices to the product

( Warning Lamp and others).

9. Sensor In : This terminals can be connected to external sensors.

10. Audio In: RCA audio in terminals. You can record four channels at the same time.

11. Audio Out: RCA audio out terminal.

12. HDMI : HDMI output for HD monitor

13. Xbox Extender (option) : Connect to xbox for VGA and USB extention with

FTP cable (Refer to Appendix A)

※

For more details, refer to [CH 2. Installation Method and Cautions].

10

CH 2 Installation Method and Cautions

CH2. Installation Method and Cautions

2-1. Cautions

WARNING

Risk of electric shock.

Do not open the cover of the product.

Servicing of this product by unauthorized personnel is prohibited and will result in a void of warranty.

In order to ensure the most stable conditions for power, the use of a UPS (Uninterrupted

Power Supply) is recommended.

- Avoid installing the product where there are direct rays or it is hot by locating near from heat generator. (May cause fire)

- Do not put vase, flowerpot, cup, cosmetics, drug, and anything the contain water on product. (May cause fire or electric shock, and it may injure people by falling)

- Do not insert or drop any metal object (coin, hair pin) or flammable object (match, paper) into air hole. (May cause fire or electric shock)

- Do not put any heavy object on it. (May injure people by being fell or destroyed.)

- Put power plug surely not to be moved. (If not, this may cause fire.)

- Unplug power plug and antenna when there are thunders and lightening. (May cause fire.)

- For cleaning the product, wipe surface with dry towel. Using chemical agent or cleaner may change the color and unpeel paint. Do not put several plugs at same time. (May cause electric shock.) If there is smoke or strange smell, stop operation. In this case, turn the power off and unplug it, and then contact our service center. (If you keep using it, this may cause fire or electric shock.)

- Do not unplug by pulling cord. (If cord is damaged, it may cause fire or electric shock.)

- Do not plug or unplug with wet hands. (May cause electric shock.)

11

CH 2 Installation Method and Cautions

- Keep the power cord untwisted. (May cause fire or electric shock.)

- Use proper adapter. (Using too much electric power may cause fire or electric shock.)

- Do not install it at where exposed to rain and wind and water drop. (May cause fire, electric shock and transformation.)

- Keep away from fire. (May cause fire.)

-Do not disassemble or remodel on your own. (May cause malfunction or electric shock.)

- Do not put next to flammable materials like flammable spray. (May cause fire.)

- Do not install it at a place with too much dirt. (May cause fire.)

- Do not install it on unstable places like shaking table and inclined place or shaking place. (May injure users by falling down or being upside down.)

- Do not put an heavy object on power cord or avoid it from being pressed by the device. (May cause fire or electric shock.)

- In case of using extension cord, do not use several devices at same time. (May cause fire with abnormal heating of extension.)

- When there are dirt on power plug pin or power outlet, clean it nicely. (May cause fire.)

-Do not damage on power cord or plug, and bend or twist or pull too much, and put it between other objects or heat. If power outlet insertion part is not tight, do not use it.

(May cause fire or electric shock.)

-Do not drop or give a shock to the product. (May injure people or cause malfunction.)

- Do not put any object too close to block cooling fan. (May cause fire.)

- In case of exchanging batteries with improper type, there might be danger of explosion.

- For used batteries, throw away separately from other garbage.

- When you take out batteries, avoid children from eating them by mistake. Keep them away from children. (If a child ate them, contact a doctor right away.)

12

CH 2 Installation Method and Cautions

Note :

This equipment has been tested and found to comply with the limits for a Class A provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

This device complies with the part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operations.

This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

CE Warning : This is a Class A product. In a domestic environment this may cause

This product has obtained EMI registration.

13

CH 2 Installation Method and Cautions

2-2 Product Installation

d t b d f d it i d f lt d dditi ll the sensor, microphone, speaker and PC for network can be connected if necessary.

2-2-1. Power Connection

1) Connect adapter cable to power connection terminal at rear side.

2) Input AC power to the adapter. (free voltage from 100V to 240V, 50/60Hz)

※ You must operate it at the rated voltage instructed on the user's manual. In case hi h h h d l i li d i d d

2-2-2. Connecting External Device

※ Connect it when power of the product is off.

※ Read through user's manual for the device you are connecting carefully.

MIC

CAMERA

Connect cameras to VIDEO IN by channels.

Connect microphone (AMP) to AUDIO IN by channels.

Connect VIDEO OUT to VIDEO IN of monitor.

Connect HD output to HD Monitor.

Connect AUDIO OUT to AUDIO IN of monitor (or speaker).

Connect Spot output to Composite Monitor.

14

CH 2 Installation Method and Cautions

2) How to connect external sensor

Sensor terminal is composed of 1 input channel and 1 output channel. Sensor out

SENSOR

+

POWER

SIREN

Sensor In : Connect the sensors. The sensor are composed of both signal and ground terminals, with a voltage difference of 5V. In the case that the sensor used for input is of the N/O (Normal Open) type, when the voltage difference between the signal and ground falls to 0V (short), the DVR can use this as a trigger to start alarm/sensor b d di

Sensor Out : Connecting external electrical devices

The relay output terminal does not provide power, and functions only on an ON/OFF basis via a relay. Normally, the signal and ground should be on an OPEN basis, and the DVR will complete the relay connection.

3) Connecting with PC using LAN cable

If you want to connect DVR to PC directly, use LAN cable, and if you want to use HUB, connect cable via hub.

*Hub : This is a device connecting one office to devices located near with using cable when you organize LAN

*Cable : This is standard UTP cable used for communication among devices through Hub and others when you organize LAN

PC

HUB

15

CH 2 Installation Method and Cautions

4) Connection Using PTZ camera

In case of using pan and tilt cameras, connect PAN/TILT DRIVE to product as t f ll i fi

VIDEO CABLE

SPEED

DOME

RS485 CABLE

5) Installing Hard disk drive

drive on the hard bracket. Remember that the main power should be off to install the hard disk drive. If you have any trouble, please contact the technical support.

16

CH 3 How to Use

CH3. How to Use

3-1. General Usage Information

The ULTIMA series DVR can be operated with a mouse or remote controller under the four main modes listed below:

Live Mode – This is the “main or default” mode. From this mode you can view in real time all currently operating cameras, information regarding camera status, and have access to Pan/Tilt camera controls. In addition, system status information will b h d i li d d th d b t d f Li d

Setup Mode – The user will be able to customize settings for Live viewing,

Recording, Backup, and Camera related devices under the Setup Mode.

Search Mode – In Search Mode, the user will be able to review all recorded footage in the case that an event must be reviewed using a calendar or event based search.

d h ill b bl hi h d i d d the preferred supported media of their choice (ex. CD, DVD, USB Backup, Remote

Client Software, etc.)

Password Protection – The DVR system will utilize a user ID and password system to prevent unauthorized usage of this product. Control of the system will only be possible after entering a proper ID and password as illustrated below. (Factory

Default settings are blank for these fields).

IDs and passwords should be managed by a system administrator, as different users may be given different levels of access to the DVR.

17

CH 3 How to Use

3-2. LIVE Mode

I hi i ill k h li h id d i 1 4 6 8 9 12 16 well as auto sequencing, PTZ Control, Mouse control, Setup configurations, Backup

3-2-1. LIVE Mode Control

1) Live View Status

You may use the Live Menu Bar located at the bottom for quick shortcuts and view status of certain items.

Recording indicator di i di

Motion detection indicator

Sensor activation indicator

2) Live Menu Bar

You may use the Live Menu Bar located at the bottom for quick shortcuts and view status of certain items.

18

CH 3 How to Use

Date

Time

Screen Split mode change

Sequence activation

Hard drive usage

Lock/ Unlock indicator

Scheduler activation indicator

Audio out channel indicator

Mute indicator

3) Live Popup Menu

By Right-Clicking anywhere on Live Screen, you may view the Live Popup Menu.

By using the Live Popup Menu, you can quickly jump to the necessary configuration and settings.

19

CH 3 How to Use

3-2-2. LIVE Mode Feature

1) Split

Change video split mode for Live View.

20ch : 1/6/12/20 Split Mode

2) Audio Out

You can choose the audio out from this menu.

3) Instant Replay

This is very convenient function to catch the abrupt accident. During live viewing, you can go directly to the playback screen.

If you choose the ‘Instant Replay’ , the DVR goes to the ‘PLAY’ with the present time screen. And you can use the functions related playback.

20

CH 3 How to Use

4) Backup

t t t th b k Th fi t i th t i ht li k th li screen, and the second one is that enter directly from ‘Search’ upon playback. If you choose the ‘backup’ from the live menu, below backup screen appears.

• You can set the backup device, time and channel from the backup screen.

• After that, if you push the ‘Estimation’ button, it will show the estimated backup file size.

• Then click the ‘Start’ button.

WARNING

Do NOT remove the backup device till end sign. The device and system may be damaged.

21

CH 3 How to Use

5) PTZ (Pan, Tilt and Zoom)

ibl t t l th d tilt b it lf P th ‘PTZ’ b tt t enter the PTZ mode. For Menu setting, you can set it by pressing button as displayed at bottom of window.

• You can set the direction of camera by using the arrow buttons.

• Setup : If you press Setup using mouse (or Menu button on the remote controller) in PTZ Menu, PTZ setup window will appear. You can set the pan and tilt speed, 32 preset name and tour sequence as well as dwelling time,

• Zoom In/Out : You can zoom in/out with mouse or play /backward buttons on the remote controller.

• Focus In/Out : You can adjust the focus with mouse or slow buttons on the remote controller.

• Iris In/Out : You can adjust the iris with mouse or ff/rew buttons on the remote controller.

22

CH 3 How to Use

•Preset : You can enter the preset number using the keypad appearing the preset button or ‘Enter’ button on the remote controller.

6) Zoom

Digital zoom of live screen for selected channel. It can be 2x zoom and also control the position by mouse dragging.

23

CH 3 How to Use

7) Sequence

Sequence Mode On /Off: Switches screens as set on Dwell time under Screen Setup

8) OSD

This feature shows current settings of product through GUI (Graphic User

Interface) and INFO button at front side is used for this feature. When you turn on power, this will show current date and time, System Lock Setting, HDD usage, Video Loss Check, Sensor ON/OFF, Motion Detection Check, Recording Stat us and Schedule Feature Usage. As you press INFO button once more, GUI disappear->OSD disappear->GUI appear->OSD appear will happen sequentially.

※ GUI (Graphic User Interface): displaying current status on monitor as images

※ OSD (On Screen Display): displaying current status on monitor as character

9) Lock/Log In

Logs off current user and locks DVR from any further configuration and screen setup until next Administrator logs in.

24

CH 3 How to Use

3-3. Search Mode

Search mode consists of two different modes of searching. The video data can be selected by

Time or Event.

Search Month / Day / Time selection.

Select from Event Log

3-3-1. Search Selection Type

1) Time Based search selection

- Select the Date you wish to view by selecting a Date from Calendar

- Select time you wish to view by selecting a time from Time Line

- Preview pane above the time bar will show preview of the currently selected video

- You may click on Refresh, Option, Backup, Import, To Live, To Play for additional

25

2) Event Based Search Selection

CH 3 How to Use

- Select search date from calendar

- Event log will be displayed according to the chosen date

- Preview pane above the Event Log will show preview of currently selected video

- You may click on Refresh, Option, Backup, Import, To Live, To Play for additional features and options

3) Miscellaneous Search Options

R l d ll d t li t

Search option.

Backup recorded data to external USB device.

Playback recorded data from external USB device

Load playback data to full screen mode.

26

CH 3 How to Use

3-3-2. Play Mode

If you choose ‘to play’, the full screen appear. You can control the play speed in here.

▶ Play Screen GUI

1. Split Screen

3. FB (Fast Backward): FB×2, 4, 8, 16, 32, 64 times faster

4. Playback : Backward normal speed

5. SB (Slow Bacward):SBx1/2, SBx1/4

6. STILL (Pause) / Frame advance

7. SF (Slow Forward):SFx1/2, SFx1/4

8. Play : Forward normal speed

9. FF (Fast Forward): FF×2, 4, 8, 16, 32, 64 times faster

11. Status information

27

CH 3 How to Use

3-4. SETUP Mode

S t f Ri ht Cli ki b tt t P M

Configure Display, Record, Device, Network, System which is navigated by clicking on corresponding tab menu at the top of the screen

3-4-1. Display

Configure OSD, Main Display, Color Control setting.

1) OSD

You may configure and/or view Date Format / Time Format / Language / Alpha

Blending / OSD / Information Bar options

Date Display Format: Select from YYYY/MM/DD, MM/DD/YYYY, DD/MM/YYYY

Time Display Format: 24H – 24hour military time

Language

12H (AM/PM) – 24 Hour separated by AM/PM

: Select system language

Alpha Blending: Adjust transparency of System Menus

OSD : OSD On/Off

Information Bar: Information Menu Bar Hide/Auto hide/ Show always

Default : Factory default all configuration values

Apply : Save current page configuration

28

CH 3 How to Use

2) Display

Monitor : You can choose the monitor between VGA and composite. The screen size will be optimized with the selected monitor.

Full Screen 4:3 ratio: Set the full screen ratio from 16:9 to 4:3 for getting original picture.

3) SPOT Control

Set the SPOT output .

You can set the SPOT output.

- Sequence dwell time: Adjust the switching time.

- Switching : You can program the sequence time. If you want to just see ch1, you set all box to ‘1’. You can make any useful sequence by this map.

29

3) Color Control

Adjust color control for Video.

CH 3 How to Use

You can adjust images of camera by channels.

- Contrast: Adjust contrast of camera.

- Brightness: Adjust brightness of camera.

- Saturation: Adjust saturation of camera.

- Hue: Adjust color of camera.

30

CH 3 How to Use

3-4-2. Record

Configure and view Event In, Record, Group, Holiday settings

1) Record

With this menu, you can set the recording variables of DVR and the Scheduler.

1) Rec type: to set conti, event, C/E(conti and event) and none(not recording).

2) Audio Rec: to select audio recording or not.

3) Conti Recording: continuous recording mode setting.

① Resolution: This is the D1 real time machine. Therefore the resolution fixed to

② FPS: Set recording frame rate. 1,2,3,5,6,7.5,10,15,30 are possible You can check the total number of frames in ‘Total’ .

31

CH 3 How to Use

③ Quality: Set picture quality. As quality gets higher, screen quality gets better but saving period gets shorter because file size gets bigger. There lit h S Hi h M di d L

To save the setting, choose ‘Apply’ after setting.

4) Event Recording

This is a window setting Event Record Mode. Setting method is same as Conti

Recording method. Conti Recording and Event Recording can be operated simultaneously.

So during no event input, DVR records by Conti recording settings. However if there is an event , it starts recording by Event Recording settings during Time(sec).

This function is very useful when you want to operate with the mixture mode.

- Duration(sec): to set post event recording time. You can choose between 1~59 seconds.

- Pre alarm(sec): to set pre event recording time. You can choose 1~4 seconds.

* Event recording has priority in recording. In C/E recording, the recording will follow conti recording setup in normal condition while it would follow event recording setup in event generation.

* For convenience, you can use the ‘Apply All’ menu to change with the same function.

[When Scheduler On]

If you select Schedule , following [Schedule Recording] setting window appears. If you choose Schedule On, the weekly scheduler is activated. Since you can set recording weekly, you can reduce recording of unnecessary time period. In Scheduler window, days and channels are displayed, and recording information for each

<How to set the weekly scheduler>

1. Choose 'Scheduler' to 'On'.

2. Choose group and drag to wanted time.

3. Press the time bar if you want to set the detailed time.

4. Press ‘Enter' button to change the group of the selected area.

5. If you activate ‘Holiday’ scheduler, choose ‘holiday’.

32

CH 3 How to Use

2) Group

‘Group’ tab, you can see the similar screen with ‘Record’. The setting is similar.

*In recording, Schedule recording setting is most preferred. So if you activate the weekly scheduler, you cannot record manually.

33

CH 3 How to Use

3) Holiday

With this menu, you can add the holidays. Use the ‘Add’ button for adding the holiday and use the ‘Delete’ or ‘Delete All’ buttons for removing the existing holidays.

34

CH 3 How to Use

4) Event In

With this menu, you can set sensor input, motion detection setup. You can also set each channel individually. Each channel may be configured to M (Motion) / S

(Sensor) / V (Both)

* Summary regarding as Event Recording

di

Sensor detection and recording

MD,Sensor detection and

Recording

MD,Sensor

Detection and nonrecording

Event Input

MD

Sensor

MD/Sensor

None

Motion

Detection

ON

OFF

ON

ON

Sensor Setting

OFF

ON

ON

ON

*In REC Menu, MD recording, Sensor detection recording, MD, Sensor detection recording and no recording are determined according to Event Input.

*Although you set Motion Detection and Sensor Setting to On in Event menu, if

Event Input in Rec Menu is set to None, it only detects and does not record.

35

CH 3 How to Use

3-4-3. Device

Configure and view Camera, Private Zone, Audio, Motion Detection, Alarm

Out, PTZ settings and Controller.

1) Camera

You may configure and/or view camera video type and general camera configuration.

•Channel Name: You can set the camera name.

•Disable : Disable current camera. It is useful when the signal is bad.

•Covert : Hide current camera from Live view but Record for future searching option

2) Private Zone

If you want to hide some part of the picture for privacy, you can choose the area by dragging the mouse. The selected area will be changed to mosaic screen.

① All On : All area will be mosaic.

② All Off : .No mosaic

③ Apply all : apply the setting to whole channel

36

CH 3 How to Use

3) Audio

•Audio Out: Select which channel will be heard during Live View.

4) Motion Detection

Change settings for Motion Grid selection and Sensitivity Level. You can set multiple area.

① Sensitivity.: 3 steps

② All On/Off : This will activate or deactivate the motion detection of the all area.

③ Apply all : apply the setting to whole channel

37

CH 3 How to Use

5) Alarm Out

setting is related that which trigger will be activate the action such as Relay, Popup, and Buzzer Alarm Out. Each type can have separate Duration value and also linked to selected camera.

• Duration Time from 5 seconds to 60 seconds

• Sensor Type: Selectable option is N.O. (Normally Open) / N.C. (Normally Close)

38

CH 3 How to Use

6) PTZ

Configure Pan/Tilt/Zoom camera for control via DVR System and Remote client

Driver: Choose Driver to be suitable for PAN/TILT Camera manufacturer.

You have to set Comport value according to the connected camera. There are more kinds of camera which can be supported. Please contact the tech support

PELCO D type

PELCO P type

PANASONIC

ORIENTAL

LPT-A100L

LG-SD110

Baudrate

9600~2400

2400

2400~19200

2400(Fixed)

9600(Fixed)

2400~19200

* For connection of PAN/TILT Camera Receiver part, refer to user's manual of the related PAN/TILT Camera.

7) Controller

This sets the ID of remote control. If you have many DVRs in the same place, you can control separately the DVR by different remote control ID.

Use the ID setup and number key to set the ID of remote control on the remote controller. You may check the ID by pressing the remote control key. The ID should be the same between the DVR and remote control.

39

CH 3 How to Use

3-4-4. NETWORK

C fi

1) Address

d i Add P DDNS E il C l

Configure Network information for Remote client connection d S i

• DVR Name : Type the URL of DVR using virtual keyboard.

• Type : It can be supported only Ethernet

• DHCP (Dynamic Host Configuration Protocol)

Set whether you want to use DHCP or not (On/Off)

If you connect LAN after setting it to On, IP is allocated automatically. If you set it to Off, you have to input IP. DHCP is a protocol that allows managers to manage

2) Port

There are 4 kinds of ports for the case such as watch, search, setup and web. You can individually set the port number of the DVR. The default is 8000. You can choose from 8000 to 9999.

If you activate ‘uPNP (Universal plug and play)’ box, DVR connects the router automatically with these port number. You don’t have to setup the router.

40

CH 3 How to Use

3) DDNS

This is the function to automatically change the IP of DVR to URL. This product supports the automatic DDNS service using manufacture’s internal server. Also you can choose Dyndns.

4) E-mail

You can send the event with snapshot by email. Fill all the information correctly and push the ‘Email Test’. Also you can select each event individually by ‘Event Set’.

41

5) Control

within 600 frames based on CIF.

① Resolution : You can choose CIF or D1 dj t th f

③ Quality: Set picture quality t

6) Status

This shows the information how many connections and what is the action of each

① Connected IP : This displays all the connected IP.

② Watch User: This displays how many connection for live viewing.

④ Setup User: This displays how many connection for DVR setting.

42

CH 3 How to Use

3-4-5. SYSTEM

Configuration settings

1) Date/Time

•Time Zone: Choose the time zone of your site. If you using the NTP function, it must be set correctly to your zone.

•Daylight Saving Time: It enables to adapt the day light saving time automatically.

• Date/Time: This sets product time. Input time by pressing number buttons after moving cursor with direction buttons. Be careful to move to backward.

The overlapped data will be deleted with warning message.

• NTP (Network Time Protocol) Server: This function is to change the time of DVR keyboard, type the address of NTP server.

2) User Authority

This sets User authority individually. You can give to each users the authorities such as setup, search, backup, PTZ, network and camera control.

43

CH 3 How to Use

3) Storage

•Display the information and usage of the hard disk drives. If you press the ‘Format’ button on each HDD, only that HDD will be formatted.

•Total : Display all the HDD usage being used for the product. If you press the ‘Enter’ button on here, all the hard disk drives will be formatted.

• HDD Overwrite : Determine whether you want to continue recording if there is no

•Mirroring : If you install two hard disk drives, you can set the second drive as a backup drive by mirroring. The mirrored disk size will be the same or greater than master HDD.

• Auto Deletion : You can select the holding period of the data. If you choose ‘OFF’, the DVR keep the maximum data regarding the HDD capacity.

4) S.M.A.R.T (Self-Monitoring Analysis and Reporting Technology)

Thi f ti l t drivers automatically. b th h d di k d i d i ti t th t t f th

•Check day : Determine the date to perform the SMART.

B t th b f f h i th

•Check Time : Temperature check period

•Limit : The upper tolerance of the hard disk drive temperature

•Alarm out : You can choose Buzzer or Relay

44

CH 3 How to Use

5) System Log

You may view all System administration log from Setup Æ System Æ System Log.

Also you can export the system log and easily send it to technical support for trouble shooting.

6) Configuration

Shown at the following screen, from Setup Æ System Æ Firmware, you may view the current firmware version as well as Upgrade the firmware and additionally,

Export, Import, and Default DVR Configuration.

45

CH 5 Client Program

3-5. Firmware Upgrade

Aft i t lli th li t ft fi d th ‘N tD l d P ’ i th window programs (Start -> programs -> DVR Client -> NetDownLoader) . Please execute this ‘Net Downloader Program’ to upgrade the firmware of the DVR.

After typing the IP and password of the DVR, click the ‘Connect’ button. You can check the model name and the current version. If you can’t see the model name and

46

CH 5 Client Program

When you connect the DVR, click the ‘open’ button on the ‘NetDownloader

Program ’and select the update file and then press the ‘start’ button. You can see the b l d l d i d th DVR

☞ WARNING!!! ff h d i d l d d off manually, all memory will be deleted !

If

※ After upgrading, DVR will reboot automatically. Before rebooting, do not operate manually !

47

Trouble Shooting

Trouble Shooting

● Can't turn on power

● There is no image on monitor

● Only INFO OSD is on monitor and no image

● There is Video Loss message.

● Can't search with Client

● Is DVR connected to power supply cable?

● Are DVR and monitor turned on?

● Are cables of DVR connected?.

● Is camera turned on?

● Are cables of DVR and monitor connected?

● Is NTSC/PAL setting normal?

● Is connection between DVR and camera normal?

● Isn't another user using same

● Connect power cable

● Turn on power.

● Connect DVR cable.

● Turn on camera.

● Connect cables of DVR and monitor.

● Check whether NTSC/PAL setting is SETUP properly

● Check whether DVR and camera are connected properly

● Use it after another use finishes using it. If another user is searching DVR remotely with

●Motion Detection doesn't work well

● Isn't it too bright or too dark?

● Isn't camera installed too far away?

.

● Increase Motion Detection sensitivity.

● Install camera closer.

● Since it buffers Live images, there might be changes with actual condition. (1~2 sec)

● There are differences condition during remote monitoring

● Live doesn't work well in remote monitoring

● Is it set to True Color?

● Are PC specifications and

VGA Card specifications are appropriate?

● Refer to recommended Client

PC specifications in 4-1

Installing

Client Program?

48

Warranty

Warranty

This product guarantees free repair based on guarantee regulations only if the malfunction is caused while customers were using it properly.

Warranty Period

Warranty period begins from the day this product is delivered to customer.

Model Name

Warranty

From . . . To . . . (for year)

User

Retailer

Address :

Company :

NAME :

Address :

Company :

NAME :

TEL :

TEL :

In case the malfunction is caused by one of following reasons, repair shall be provided as charged service.

A) If cause for the malfunction is from external condition other than the product

B) If malfunction is cased because user tried to reassemble the product

C) If malfunction is caused by natural disasters such as fire, water disaster, thunder and others

D) If malfunction is caused while transporting or moving the product after purchasing

1. All other refunds other than warranty repair for this product shall be based on actual cost.

2. Refund standard about product repair, exchange or repayment observe Regulations for Compensating Customers' Damage provided by the Economic Planning

Board.

product stops.

Address

Tel

Fax

URL

49

Appendix A How to Connect Receiver

1. Connect EXTEND FTP cable to Receiver (upto 350ft/100m).

Refer to http://en.wikipedia.org/wiki/Twisted_pair about the FTP cable.

Connect Monitor and Wired/Wireless Mouse to the Receiver

Appendix A

FTP(Foiled Twisted Cable)

Receiver

2. Because all the case has different cable length, you should adjust the GAIN and

PHASE in Receiver to get a most proper VGA output. You can use the small cross screw driver for adjusting at the edge of Receiver.

50

adjustment

3.This is the whole diagram.

Appendix A

51

Appendix B

Appendix B Catcheye for Android mobile

The Catch Eye allows for you to monitor DVRs.

It now supports Live mode. Playback mode will be added soon.

It is easy and convenient to use.

The functions of Catch Eye:

• Live View

• Channel switching

• Server management

• PTZ control

• Digital zooming

• Snapshot

The functions operated by Touch:

• Single touch : switch channel, Pan/Tilt.

• Multi touch : Digital-Zoom, PTZ Zoom-In/Out

1. Starting

When o la nch Catch E e for the first time Yo need to register ne DVR ser ers in the screenshot (as) below. Tap the menu button and select the “Add“ to continue.

52

2. Server Management

Appendix B

Enter the appropriate data of your DVR server.

Server Name : Name that you want to associate with the DVR server.

IP address : IP address(example : 192.168.1.110) or a DNS name(example :

12345.3r.global.com).

Server Port : Port number(watch port in DVR setup).

User Name : Username(default is "admin").

Password : User password.

Server Type : Embedded DVR, HD DVR, PC DVR

When you finish, tap the "Save" button.

53

The "Edit“ button modifies the information of the selected DVR Server.

Appendix B

3. Live Viewing

Tap the DVR server item and select the “Connect” in menu when you register DVR server. The app. will show “loading, Please wait” as below.

** Wait Until it receives DVR channel data, it will take a few seconds depending on the network environment. 3G will take a longer time than Wi-

Fi.

54

Appendix B

The next screen shows the first channel on DVR live view.

“Channel", “Division“, “Save“, “PTZ” or “Zoom“ buttons are shown in menu.

4. Multi Channel Viewing

- "Channel“, “Division” button -

If you select these buttons, sliding view will appear in live view so that you can change the channel or division that you want. Max channel depends on division mode works on products support over 16channels.

55

5. Image Saving

- "Save" button -

"S " b i If i b i

"Save" button, you can find the image file in your phone’s Gallery menu.

Appendix B

6. PTZ Control Mode

- "PTZ" button -

The "PTZ" button allows you to control PTZ camera

If the camera type of the channel is PTZ, the fourth button on the bottom bar

Every PTZ function is controlled by touch. You can also control zoom-in, zoom-out, focus-in, focus-out functions by tapping menu buttons.

If you tap the “Exit” button in “PTZ” mode or “Zoom” mode, channel mode will be changed to Channel-switching mode. There you can change channel by touch –to-scroll in the left or right direction.

- Pan/Tilt -

Pan/Tilt functions are controlled by a single touch directionally. The app. will show the arrow on the screen as below.

56

Appendix B

- Zoom-In/Out -

The Zoom-in/out function is controlled by multi touch from inside to outside or from outside to inside. The app. will show “+” icon in Zoom-in mode or a“-” icon in Zoom-Out mode on the screen as below.

7. Digital-Zoom Mode

If the camera type is not pan-tilt, you can control the Digital zoom function.

supported functions are as below.

- Digital Zoom-in

- Digital Zoom-out

Every Digital Zoom function is controlled by your touch. Digital Zoom-in function is controlled by multi touch from inside to outside.

Digital Zoom-out function is controlled by multi-touch from outside to inside.

57

Appendix C

Appendix C Catcheye for iPhone

The Catch Eye allows for you to monitor DVRs.

It now supports Live mode. Playback mode will be added soon.

It is easy and convenient to use.

The functions of Catch Eye:

• Live View

• Channel switching

• Server management

• PTZ control

• Digital zooming

• Snapshot

The functions operated by Touch:

• Single touch : switch channel, Pan/Tilt.

• Multi touch : Digital-Zoom, PTZ Zoom-In/Out

1. Starting

When o la nch the Catch E e for the first time Yo needs to register ne DVR ser ers in the screenshot as below. Tap the “Add server“ button to continue.

58

2. Server Management

Appendix C

Enter the appropriate data of your DVR server.

Title : Name that you want to associate with the DVR server.

IP address : IP address(example : 192.168.1.110) or a DNS name(example :

12345.3r.global.com).

Port : Port number(watch port in DVR setup).

Username : Username(default is "admin").

Password : User password.

Server Type : Embedded DVR, HD DVR, PC DVR

When you finish, tap the "Save" button.

59

The "Edit“ button modifies the information of the selected DVR Server.

Appendix C

3. Live Viewing

Go ahead and tap the DVR server item in

Addressbook table when you register DVR server.

The app. will show “loading circle icon” as below.

** Until it received DVR channel data, it takes a few seconds(it depends on network environment.

3G will be longer than Wi-Fi)

60

Appendix C

The next screen shows DVR live view for first channel.

"CH", "Save" and “Digital-Zoom" or "PTZ“ buttons are shown in the bottom bar.

4. Multi Channel Viewing

- "CH" button -

If you tap this button, sliding view will appear in live view and you can change channel and division mode. Max channel depends on server’s max h l d di i i i h l h l d h l d f you finish change channel or division, tap "CH" button in bottom bar again.

61

Appendix C

5. Image Saving

- "Save" button -

"S " b 1 h l i If i b i

"Save" button, you can find image file in iPhone's photo album menu.

6. PTZ Control Mode

- "PTZ" button -

"PTZ" button makes you can control PTZ camera f h h l i PTZ h hi d b named "PTZ". Otherwise, “Zoom“.

i h b b

Every PTZ functions are controlled by your touch. You can also control zoom-in, ill b zoom-out, focus-in, focus-out functions by tapping buttons.

If you tap the “Exit” button in “PTZ” mode or “Zoom” mode, channel mode will be changed to Channel-switching mode. And you can change channel by touch and scroll left or right direction.

- Pan/Tilt -

Pan/Tilt functions are controlled by single touch directionally. The app. will show the arrow in the screen as below.

62

Appendix C

- Zoom-In/Out -

Zoom-in/out function is controlled by multi touch from inside to outside or from outside to inside. The app. will show “+” icon in Zoom-in or “-” icon in

Zoom-Out in the screen as below.

M d

If camera type is not pan-tilt, you can control digital zoom function.

supported functions are like below.

- Digital Zoom-in

- Digital Zoom-out

Every Digital Zoom function is controlled by your touch. Digital Zoom-in function is controlled by multi touch from inside to outside.

Digital Zoom-out function is controlled by multi touch from outside to inside.

You can also control Digital zoom-in and Digital zoom-out functions by tapping “ “ and “ " buttons.

63

Appendix D

8. DVR Information

If you tap the "i“ button in top bar, you can see the DVR server’s information.

DVR server Information list :

- Server name

- Server IP address

- Channel name

- Image size

64