1 Dometic:
INSTALLATION
ВЕ
OPERATING
INSTRUCTIONS
RGE 410
E —
Ce
INTRODUCTION CONTENTS
We are pleased that you have chosen this refrigerator andhope OPERATING INSTRU CTIONS 4
you will derive much satisfaction from using it.
The refrigerator is designed for storage of foods and storage of CONTROLS... oe oo 4
frozen foods and making ice. The refrigerator is ideal for in- |
stallation in homes, farms, cottages, holiday homes, and chalets STARTING THE REFRIGERATOR ............... 4
or similar. |
The installation and servicing should only be carried out by an REGULATING THE TEMPERATURE ............. 4
authorized, qualified person and must conform to all relevant
national and local regulations FOOD STORAGE ser 4
It is important to read through these instructions carefully POSITIONING THE STORAGE RACKS 4
before using the refrigerator. CNT
To ensure good refrigeration and economical operation, the ICE-MAKINCS .......reereoeraadoroaoreorereco 5
refrigerator must be installed and used as described in these :.
instructions. DEFROSTING...........e.srecrorecorereeara. 5
ING THE REFRIGERATOR...............
TRANSIT DAMAGE CLEAN HE REFRIGERATOR 5
Inspect the refrigerator for damage. Transit damage must be TURNING OFF THE REFRIGERATOR. ........... 5
reported to whoever is responsible for delivery not later than
seven days after the refrigerator was delivered. IF THE FRIDGE FAILS TO WORK .............. 5
DATA PLATE MAINTENANCE... ВИ 5
The data plate is located inside the refrigerator. Since these SOMEUSEFULHINTS ooo, 9
details will be needed if you have to contact service personnel,
it is a good idea to make a note of them here- TECHNICAL DATA... 5
INSTALLATION INSTRUCTIONS 6
Mod: GENERAL INSTRUCTION ..................... 6
PLACEMENT OF THE REFRIGERATOR .......... 6
LP GAS CONNECTION. ..............ee.eee0.. 6
; ELECTRICAL CONNECTION ................... 7
ER LIGHTING LL Len anne T
OPERATING INSTRUCTIONS
CONTROLS
N
ON
FIG. 1
The refrigerator can be run on either mains electric or LP gas.
Changing between these modes of operation is carried out by
means of control buttons positioned as shown in fig. 1.
The energy selector (A) can be set at either e 230 - 240V),
0) GLP gas) or 0 (= off). |
The refrigerator temperature is controlled by a thermostat (B).
Please note that the thermostat has no “off” position.
The refrigerator is fitted with a safety device that automatically
shuts off the supply of gas if the flame goes out. The safety
device can be opened manually by pressing the button (С).
The piezoelectric igniter discharges sparks over the burner -
when the button (D) is pressed.
In the flame viewer (E) you can see a blue light when the gas
flame is lit,
STARTING THE REFRIGERATOR
Whilst mebile:
« Do not operate the refrigerator on LP gas.
« Turn off the gas bottle.
The position numbers refer to fig. 1.
LP Gas operation
After initial installation, servicing, or changing gas cylinders
etc., the gas pipes may contain some air, which should be al-
lowed to escape by briefly turning on the refrigerator or other
appliances. This will ensure that the flame lights immediately.
1. Make sure that all valves between the gas container and the
refrigerator are open.
2. Tum the energy selector (A) to position (),
. Push the button (C) in until it reaches the bottom - and hold,
push the button (D) for the piezo igniter several times to
Light the burner.
4. Check the flame indicator (E) to see if the flame 1s lit.
LG
5. Keep the button (C) pressed for a further 10-15 seconds,
6. Release the button (C) and check that the flame is alight.
To terminate gas operation, turn knob (A) to 0.
Electric operation
Set the energy selector (A) to position 1.
REGULATING THE TEMPERATURE
The position number refers to fig. 1.
It will take several hours for the refrigerator to reach normal
operating temperature. A thermostat controls the temperature
of the main compartment of the refrigerator. The thermostat
knob (B) should be set at 3-5. If a lower (colder) temperature is
desired set the thermostat to a higher figure.
FOOD STORAGE ~
Always keep food in closed containers. Never put hot food in
the refrigerator; allow № to cool first.
Never keep items in the refrigerator that might give off
flammable gases.
The frozen food compartment is intended for the storage of
frozen food and for making ice. It is not suitable for freezing
items of food.
Never put bottles or cans of fizzy drinks in the frozen food stor-
age compartment as they may burst when freezing. Also don’t
give children ice-lollies straight from the frozen food as they
could cause frost bums.
Most kinds of frozen food can be stored in the frozen food
compartment for about a month. This period of time may vary,
however, and it is important to follow the instructions on the
individual packets.
POSITIONING THE STORAGE RACKS
Dismantling/mounting
1. Remove the front and back securing brackets.
2. Detach the storage rack by moving it to the left (1) and then
tilt it up or down (2). Pull rack towards you and remove.
AE TE ser me ka pue
ый ла тел “Fi
Riera RT R
+ Le 1, НИЙ
da e
3. To fit the storage rack, mount in reverse order.
ICE-MAKING
“Fill the ice tray just below the brim with drinking water and
place it on the freezer shelf.
It is possible to make ice faster by turning the control knob tem-
porarily to its highest value but do not forget to turn it back to
its regular setting afterwards as the refrigerator might otherwise
become too cold,
DEFROSTING
Frost will gradually accumulate on the refrigerating surfaces, It
must not be allowed to grow too thick as it acts as an insulator
and adversely affects refrigerator performance.
Check the formation of frost regularly every week and when it
gets about 3 mm thick, defrost the refrigerator. To defrost the re-
frigerator, tum it off and remove the ice tray and all food items,
leave the cabinet and freezer doors open.
Do not try to accelerate defrosting by using any kind of heat-
ing appliance, as this might damage the plastic surfaces of the
refrigerator. Neither should any sharp objects be used to scrape
off the ice.
Defrost water runs from a drip tray to a receptacle at the rear of
the refrigerator where it evaporates. Defrost water in the freezer
compartment should be mopped up with a cloth.
When all the frost has melted, wipe the refrigerator dry and
restart it. Place the food items back inside but wait until the
refrigerator is cold before making ice cubes.
CLEANING THE REFRIGERATOR
Clean the inside of the refrigerator regularly to keep it fresh and
hygienic. Soak a cloth in a solution consisting of a teaspoon of
bicarbonate of soda to half a litre of warm water. Wring out the
cloth and use it to clean the interior of the refrigerator and its
fittings.
Never use detergents, scouring powder, strongly scented prod-
ucts or wax polish to clean the interior of the refrigerator as they
may damage the surfaces and leave a strong odour.
The exterior of the refrigerator should be wiped clean now and
again, using a damp cloth and a small quantity of detergent. The
door gasket should only be cleaned with soap and water and
then thoroughly dried.
The cooling unit behind the refrigerator should be cleaned with
a brush from time to time, but make sure that the refrigerator is
switched off when doing this,
TURNING OFF THE REFRIGERATOR
if the refrigerator is not to be used for some time:
1. Shut off any valve in the gas line to the refrigerator.
2. Set the energy selector (A) to 0.
3. Empty the refrigerator. Defrost and clean it as described ear-
lier. Leave the doors of the refrigerator and the frozen food
compartment ajar.
IF THE ‘FRIDGE FAILS TO WORK
Check the following points before calling a service technician:
« Ensure the STARTING THE REFRIGERATOR instructions
have been followed.
« Make sure the refrigerator is level,
« If it is possible to start the refrigerator on any of the connec-
ted sources of energy.
A
« Tf the refrigerator fails to work on gas, check:
- That the gas bottle is not empty.
- That all LP-gas valves are open.
« If the refrigerator fails to work on mains electric, check:
- That the mains electric supply is connected to the
refrigerator.
- That the fuse is intact.
If the refrigerator is not cold enough it may be because:
* The ventilation of the cooling unit is inadequate; see the
paragraph PLACEMENT OF THE REFRIGERATOR.
» The evaporator is frosted up.
" The temperature control setting is incorrect,
* The gas pressure is incorrect - check the pressure regulator at
the gas container.
» Too much food is loaded at one time. |
* The door is not properly closed or the magnetic sealing strip
is defective.
If the refrigerator still does not work properly, call a service
technician.
The sealed cooling system must not be opened,
since it contains corroding chemicals under high
pressure.
MAINTENANCE
Inspect the gas hose periodically for cracks or deep chafing
marks. Connections can be tested for leaks using a soap solu-
tion. DO NOT USE AN OPEN FLAME! Tf there is any sus-
picion of damage, call for a service technician. We recommend
that a service technician check the refrigerator once a year.
SOME USEFUL HINTS
Make sure that:
« Defrosting is carried out periodically.
« The refrigerator is clean and dry with the door left open
when it is not to be used for some time.
= Liquids or items with a strong odour are well packaged.
* There is a free air circulation over the cooling unit at the rear
of the refrigerator.
TECHNICAL DATA
Overall dimensions
Height 1612 mm
Width 592 mm
Depth 623 mm
Capacity
Gross 224 litres
Net 209 litres
Frozen food compartment 47 litres
Weight (without packaging) 76 kg
Electrical data
Input 230 - 240 Y 325 watt
Energy consumption/24h 39 kWh
LP gas data
Input max 1.38 MIh
Energy consumption/24h 500 г
Cooling medium Ammonia
Sodium chromate is used for corrosion protection
(less than 2 weight % of the coolant).
INSTALLATION INSTRUCTIONS
GENERAL INSTRUCTION
The installation, servicing and gas installation must be per-
formed by an authorised, qualified person and the refrigera-
tor should be installed in accordance with the manufacturers
installation instructions; local gas fitting regulations, municipal
building codes, electrical wiring regulations, AS5601 “Gas
Installations” and any other statutory regulations.
The packaging of this appliance is design to withstand the trans-
portation from the factory to the point where it will be installed
in the recreational vehicle. Before starting to install the appli-
ance, please, make sure all parts of the packaging have been
removed, so there will not be anything left that may come into
contact with heat parts of the appliance or obstruct the combus-
tion exhaust gases or the air movement around the cooling unit.
PLACEMENT OF THE REFRIGERATOR
The room should have a capacity (length x width x height) of at
least 20 m* and must be adequately ventilated as well as follow
all relevant national and local regulations. Further the room
should have a window (which can be opened) or a door to the
outside.
It is important that the refrigerator is not subject to radiation of
heat from a stove etc.
For best performance also at high ambient temperatures there
must be a free air circulation over the cooling unit at the rear of
the refrigerator.
The refrigerator is designed for a free-standing installation and
the clearance to the rear wall and to possible side walls, should
be at least 25 mm. The clearance above the refrigerator should
be at least 100 mm.
The refrigerator must be adjusted to a vertical position in both
directions. Use the feet on the refrigerator to adjust its position.
LP GAS CONNECTION
The refrigerator is designed for operation on LP gas, the
pressure of which must be 2.75 kPa for Propane. Check that this
is stated on the data plate.
The refrigerator is not designed for operation on town gas or
natural gas. |
Check that the gas supplied to the refrigerator is at the correct
pressure. See the reducing valve on the LP gas container.
The gas supply system must incorporate a pressure regulator to
maintain a supply pressure of not more than 2.735 kPa.
The supply pipe should preferable be of copper. If any other
material is used, it must be of a type approved for use with con-
tinuously operating bottled-gas appliances, and have threaded
connections throughout.
All connectors etc. should be of a type specifically designed for
the type and diameter of the connection pipe used, and screwed
joints should be sealed with a joining compound approved for
use with bottled gas,
The gas supply pipe should be connected to the gas valve at
the rear of the refrigerator, by means of a suitable threaded
coupling. The gas valve is furnished witha ISO 7/1 -Rp 1/8 -
internal pipe thread connection.
From the side
At least |
25 mm ZB
a |
Г an
у
From above
Wall
ZZ A A
of Г
y
я 4 1425
с
8
od
7
Wall
In making the connection to the refrigerator, a union gas cock of
an approved bottled-gas type must be incorporated in the supply
line in a position that is readily accessible to the user.
For servicing purposes, the union should be on the outlet side
of the cock and the pipework should be positioned so as not to
prevent the refngerator from being readily withdrawn.
All completed connections should be checked for leaks with
soapy water.
A DO NOT use a flame to check for gas leaks.
ELECTRICAL CONNECTION
The electrical installation must be carried out in a proper and
durable manners, taking into account all relevant regulations
and codes of practice.
For mains voltage operation, it is important that the circnit
is effectively earthed.
230-240 volts connection
Check that the voltage stated on the data plate is the same as
the main voltage in use. Plug the refrigerator power cord into
an easily accessible earthed wall socket.
Electrical leads must be routed and secured so that they
cannot come into contact with hot or sharp parts of the
refrigerator.
LIGHTING
The refrigerator is provided with a battery power interior light.
The battery box is at the rear of the refrigerator. Four batteries,
type LR20 1,5 volts are to be used.
Before leaving |
¢ Once the installation is complete, test the
operation of the refrigerator and instruct the user
on its correct operation. If the appliance fails to
operate correctly, contact your local Dometic
Service provider.
">
