Speedrooter 91

™

Operating Instructions

For 3” through 10”

(75mm—250mm)

Y

our Speedrooter 91 is designed to give you years of trouble-free, profitable service. However, no machine is better than its operator.

R

ead, understand and follow all safety warnings and instructions provided with the product. Failure to follow the warnings and instructions may result in electric shock and/or serious injury. Save all warnings and instructions for future reference.

SAVE THESE INSTRUCTIONS!

Speedrooter 91™

GENERAL SAFETY RULES

WARNING! Read and understand all instructions.

Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. Replacement manuals are available upon request at no charge, or may be downloaded from our website, www.drainbrain.com

. Instructional videos are available for download on our website, and may be ordered. If you have any questions or problems, please call General’s customer service department at 412-771-6300.

SAVE THESE INSTRUCTIONS!

These instructions are intended to familiarize all personnel with the safe operation and maintenance procedures for the Speedrooter 91.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

DANGER indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.

WARINING indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury.

CAUTION indicates a hazard with a low level of risk which, if not avoided, will result in minor or moderate injury.

2

Electric shock resulting in death can occur if you plug this machine into an improperly wired outlet. If the ground wire is electrified, you can be electrocuted by just touching the machine, even when the power switch is off.

A ground fault circuit interrupter will not protect you in this situation. Use a

UL approved tester to determine if the outlet is safe.

Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.

Power tools create sparks which may ignite the dust of fumes.

Only wear leather gloves.

Never use any other type of glove, such as cloth, rubber, or coated gloves. Never grasp a rotating cable with a rag.

These items could become wrapped around the cable and cause serious injury.

Always wear safety glasses and rubber soled, non-slip shoes.

Use of this safety equipment may prevent serious injury.

Never operate machine with belt guard removed.

Fingers can get caught between belt and pulley.

Do not overstress cables.

Overstressing cables may cause twisting, kinking, or breaking of the cable and may result in serious injury.

GENERAL SAFETY RULES

Work Area

1.

Keep work area clean and well lit.

Cluttered benches and dark areas invite accidents.

2.

Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.

Power tools create sparks which may ignite the dust or fumes.

3.

Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

Electrical Safety

1.

Grounded tools must be plugged into an outlet, properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way.

Do not use any adapter plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded.

If the tool should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user.

2.

Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators.

There is an increased risk of electric shock if your body is grounded.

3.

Do not expose power tools to rain or wet conditions

.

Water entering a power tool will increase the risk of electric shock.

4.

Do not abuse the cord

. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.

5.

When operating a power tool outside use an outdoor extension cord marked “W-A” or “W” .

These cords are rated for outdoor use and reduce the risk of electric shock.

6.

Test the Ground Fault Circuit Interrupter (GFCI) provided with the power cord to insure it is operating correctly before operating machine.

Machine must have a properly functioning ground fault circuit interrupter on the power cord. GFCI reduces the risk of electric shock.

7.

Only use proper three-wire extension cords in good condition which have three-prong grounding plugs and three-pole receptacles which accept the tool‟s plug.

Use of damaged, inferior, or other extension cords will not ground the tool. Increases the risk of electric shock and bodily injury or death.

8.

Extension cords are not recommended unless they are plugged into a Ground Fault Circuit Interrupter (GFCI)

found in circuit boxes or outlet receptacles. The GFCI on the machine power cord will not prevent electric shock from the extension cords.

9.

Keep all electric connections dry and off the ground

. Reduces the risk of electric shock.

3

Speedrooter 91™

10.

DO NOT touch plugs or tools with wet hands.

Reduces the risk of electric shock.

Personal Safety

1.

Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication.

A moment of inattention while operating power tools may result in serious personal injury.

2.

Dress properly. Do not wear loose clothing or jewelry.

Contain long hair. Keep your hair, clothing, and gloves away from moving parts.

Loose clothes, jewelry, or long hair can be caught in moving parts.

3.

Avoid accidental starting.

Be sure switch is off before plugging in.

Plugging in tools that have the switch on invites accidents.

4.

Remove adjusting keys or switches before turning the tool on.

A wrench or key that is left attached to a rotating part of the tool may result in personal injury.

5.

Do not overreach.

Keep proper footing and balance at all times.

Proper footing and balance enables better control of the tool in unexpected situations.

6.

Use safety equipment. Always wear safety glasses and rubber soled, non-slip shoes

. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

Tool Use and Care

1.

Use clamps or other practical way to secure and support the workpiece to a stable platform. Do not force tool

. Holding the work by hand or against your body is unstable and may lead to loss of control.

2.

Do not force tool. Use the correct tool for your application.

The correct tool will do the job better and safer at the rate for which it is designed.

3.

Do not use tool if switch does not turn it on or off.

Any tool that cannot be controlled with the switch is dangerous and must be repaired.

4.

Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool.

Such preventative safety measures reduce the risk of starting the tool accidentally.

5.

Store idle tools out of reach of children and other untrained persons.

Tools are dangerous in the hands of untrained users.

6.

Maintain tools with care.

Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting edges are less likely to bind and are easier to control.

7.

Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool‟s operation

. If damaged, have the tool serviced before using.

Many accidents are caused by poorly maintained tools.

Speedrooter 91™

8.

Only use accessories that are recommended by the manufacturer for your model

. Accessories that may be suitable for one tool may become hazardous when used on another tool.

Service

1.

Tool service must be performed only by qualified repair personnel.

Service or maintenance performed by unqualified repair personnel could result in injury.

2.

When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual.

Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury.

SPECIFIC SAFETY RULES

1.

Only wear leather gloves

.

Never use any other type of glove, such as cloth, rubber, or coated gloves.

Never grasp a rotating cable with a rag. These items could become wrapped around the cable and cause serious injury.

2.

Never operate machine with belt guard removed

.

Fingers can get caught between belt and pulley.

3.

Do not overstress cables

. Keep leather-gloved hand on the cable for control when machine is running. Overstressing cables because of an obstruction may cause twisting, kinking, or breaking of the cable and may result in serious injury.

4.

Place the machine at a distance not greater than two feet from the opening

. Greater distances can result in cable twisting or kinking.

5.

Machine is designed for ONE-PERSON operation.

Operator must control foot switch and cable.

6.

Do not operate machine in reverse (REV).

Operating machine in reverse can result in cable damage and is used only to back cutting tool out of an obstruction.

7.

Keep hands away from rotating drum.

Do not reach into drum unless machine is unplugged. Hand may be caught in the moving parts resulting in serious injury.

8.

Be careful when cleaning drains where cleaning chemicals have been used.

Avoid direct contact with skin and eyes. Drain cleaning chemicals can cause serious burns as well as damage the cable.

9.

Do not operate machine if operator or machine is standing in water

. Will increase risk of electrical shock.

10.

Wear safety glasses and rubber soled, non-slip shoes.

Use of this safety equipment may prevent serious injury.

11.

Before starting each job, check that the cable in the drum is not broken or kinked, by pulling the cable out and checking for wear or breakage

.

Always replace worn out (kinked or broken) cables with genuine GENERAL replacement cables.

4

12.

Only use this tool in the application for which it was designed. Follow the instructions on the proper use of the machine.

Other uses or modifying the drain cleaner for other applications may increase risk of injury.

Ground Fault Circuit Interrupter (GFCI)

Your machine is equipped with a ground fault circuit interrupter, which protects you against shock if a short circuit should occur. Check that receptacle is properly grounded. Test the GFCI before each use.

1. Plug into 120-volt receptacle.

2. Push test button. Indicator light will go out and power to machine should cut off.

3. If light does not go out when test button is pushed, equipment should not be used until proper repairs can be made.

4. To restore power after test, push reset button. With the reset button depressed, if the machine doesn't start, stops while running, or if the operator experiences a mild shock,

do not use the machine!

Tag the machine out of service and take it to a motor repair center or return it to the factory for repairs.

THE SECTION OF CORD BETWEEN THE WALL PLUG

AND THE GFCI IS NOT IN THE PROTECTED CIRCUIT.

FEATURES

Truck

Loading

Wheel

Motor

Switch

Stair

Climbers

Wheel

Brake

V-Belt

Drum

Adjustable Height Handle

Distributor Tube

Belt Guard

Feed Pressure

Control Knob

Speedrooter 91 shown (Right) with Cable Guide Tube

(Cat. # S91-GT)

Feed

Control

Lever

Cutter

Foot Pedal

Cable Application Chart (Table 1)

Cable Size Pipe Size Typical Applications

3/4”

(Large Drum)

4” to 10”

5/8”

(Large Drum)

1/2”

(Small Drum)

3” to 6”

2” to 4”

Large Drains, Long Runs,

Roots

Floor Drains, Roots

Stacks & Small Drains

(No Roots)

Speedrooter 91™

POWER CABLE FEED

Feed Pressure Knob Feed Control Lever

Reverse

Neutral

Cutter Application Chart (Table 2)

Cutter Cat. # Typical Applications

Raised Cap

Forward

Cutters for 1/2” Cables

Arrow

Head

AH

Starting Tool, ideal for cutting and scraping.

OPERATION

SET-UP

1-1/2”

U-Cutter

Small

Retrieving

Tool

13” Flexible Leader LE-1

Spear

Head

2”

U-Cutter

3” & 4”

Side

Cutter

Blades

3” Heavy

Duty Saw

Blade

4” Rotary

Saw Blade

Tool for negotiating around difficult bends.

Cutters for 5/8” and 3/4” Cables

SHD

2UC For Cutting and Scraping

3SCB

&

4SCB

Starting Drill—gets water flowing.

For Cutting—Scraping walls of pipe.

3HDB For Cutting Roots

4RSB For Cutting Roots

Large

Retrieving

Tool

26” Flexible Leader LE-3

Helps cable get through tight traps and bends.

Note: There are no fixed rules for what cutter to use. If one tool doesn’t take care of a stoppage, simply try another.

5

MAKE SURE THE MOTOR SWITCH IS IN

THE „OFF‟ POSITION!

1.

Place machine at a distance not greater than two feet from the drain opening. Be sure the Speedrooter

Guide Tube (S91-GT) is in place. If you can't get the machine this close to the drain opening, run the cable through the optional Guide Tube Extension (GTE) or a metal guide tube to prevent cable whipping.

2.

Position the air foot pedal for easy accessibility. The machine is designed for one-person operation. Be sure you can quickly remove your foot from the pedal in an emergency.

3. Lock the wheels by lifting the brake handle located next to the left wheel and pressing it into the clip.

4. Be sure the motor switch is in the

off

position.

5. Make sure the Power Cable Feed is set to match the cable size you have selected. If you’re using 3/4" or

5/8” cables, the feed should be assembled with the raised side of the lower two caps outward. If you are using 1/2" cables, the feed should be assembled with the raised side of the caps inward.

6. Select the proper cutting tool (See Cutter Application

Chart—Table 2). A good tool to start with is the

Spearhead or 2” U-Cutter. If you are having difficulty getting around a P-Trap or close bend, try the flexible leader. After the line has been opened, follow with larger blades, which scrape the inside edges of the pipe, assuring a real cleaning job.

7. Insert the cutter into the female connector at the end of the cable and tighten the connecting screw and lock washer

firmly

in place.

Speedrooter 91™

OPERATION

1. Before stepping on the foot pedal, pull cable from the drum and slide it into the drain as far as it will go.

2. Tighten the knob at top of the Power Cable Feed so that the feed roller presses against the cable. Be sure not to over tighten since this could cause excess cable wear.

3. The feed lever controls the feeding rate and direction of the cable. Move the lever down to feed cable out of drum. The further the lever is moved downward, the faster the cable will feed out. Move lever up to retract cable into drum. When the lever is in the middle (neutral) position, cable will spin in place.

4. Move the motor switch to the

forward

position.

5. With a gloved hand on the Guide Tube, depress the air foot pedal to start machine. Feed the cable into the line and against the obstruction with a firm, even pressure. Adjust the feeding rate to the resistance met. Do not force the cable - let the cutter do the work. The job won’t go any faster and you could damage the cable.

6. Don't leave too much slack in the cable since this will cause whipping. If the cable starts to bend or build up too much twist, release pressure on the foot pedal and rotate the drum in the opposite direction to relieve the twist on the cable. Push any excess cable back into the drum and then continue.

7. If you're having trouble getting around tight bends, try putting the machine in reverse while applying steady pressure.

10. Be careful not to let the cutter get caught in the stoppage as you work through it. This can cause kinking and breaking of the cable. When you feel the cable starting to twist in your hands, stop the machine and retract the cable. This will free the cutter from the obstruction. Then allow the cable to move forward slowly into the stoppage. Remember, no cutting takes place when the blades stop turning.

11. After the line has been opened, retract the cable by moving the feed lever up. Make sure the motor switch is in the

forward

position. This is important to prevent the cable from tangling in the drum or in the line.

12. When the cutter is near the drain opening, take your foot off the pedal to stop drum rotation. Never retract the cutter from drain while cable is rotating. The cable could whip and cause serious injury.

DO NOT USE REVERSE TO PULL THE

CABLE OUT OF THE DRAIN.

RUNNING MACHINE IN REVERSE

CAN CAUSE THE CABLE TO TANGLE

IN THE DRUM.

SPECIAL OPERATIONS

IF CABLE GETS CAUGHT IN LINE

The motor can be reversed to free the cable if it gets caught in line. (Note: if using Power Cable Feed, putting motor in reverse will cause the feed control lever to operate opposite of normal.)

1. Move motor switch to the reverse position.

2. Depress the foot pedal while pulling on the cable.

3. After cable is loose, move switch back into forward position.

DO NOT RUN MOTOR IN REVERSE FOR

MORE THAN A FEW SECONDS AT A TIME

SINCE THIS COULD CAUSE THE CABLE

TO KINK OR TANGLE IN THE DRUM.

Don't do this for more than a few seconds at a time since this could cause tangling in the drum or kinking.

8. If you still can't get around the bend, you're probably using too large a cable. Switch to a 5/8" or 1/2” diameter cable. (See Cable Application Chart—

Table 1)

9. When the cable reaches the stoppage, allow the cable to progress forward slowly, chewing into the stoppage as it goes. This slow forward movement will reduce stress on the cable while doing a more thorough cleaning job. A back and forth action often works best.

Hint:

It's often helpful to have a small stream of water running in the line to wash the cuttings away while the machine is in operation and after.

IF CABLE TANGLES IN DRUM

This is caused by using too much pressure when feeding the cable or feeding the cable into the line while running the machine in reverse. To untangle the cable, rotate the drum in opposite direction. This will usually get the cable to lie in the drum properly.

If the cable has become badly tangled, which shouldn’t occur if used properly, it can be straightened out by removing the distributor tube from the machine. To do this:

DISCONNECT MACHINE FROM POWER

SOURCE BEFORE UNTANGLING CABLES

6

1. Remove drum from machine frame. (See TO RE-

MOVE DRUM.)

2. Set drum down so that distributor tube is pointing up.

Unscrew knob at the back of distributor tube. (See

Figure 1.) This unlocks the distributor tube from the drum shaft. Be careful not to lose the thrust bearing and race attached to the knob.

Figure 1

3. Slide the distributor tube off the shaft and out of the drum. (See Figure 2.)

Speedrooter 91™

TO REMOVE DRUM

DISCONNECT MACHINE FROM POWER

SOURCE BEFORE REMOVING DRUM FROM

MACHINE!

1. Remove belt guard by loosening the knob above the motor.

2. Press down on motor and slide V-Belt off of drum.

Then rotate motor to the side.

3. Remove the cutter and connecting screw from the cable end.

4. Unscrew knob behind the front post and pull Power

Cable Feed off the machine.

5. Loosen the knob on front post cap (S91-120), then open cap.

6. Loosen knob on rear drum shaft clamp (S91-130), then open cap.

7. Lift drum clear of machine.

Figure 2

The tension of the cable will force the tube to the side of the drum as you pull it out; so keep some pressure against the cable as you pull the tube out. After tube is out, pull out the inner drum cage. (See Figure 3.)

Pull out enough cable to eliminate the tangle.

Figure 3

4. After the cable is straightened out, slide the inner drum cage back into place. (Figure 3.) Then slide distributor tube back so that curved section is adjacent to crescent-shaped notch in inner drum cage and back of distributor tube fits over shaft in center of drum. (Figure 2.) Keep pressing down on distributor tube as you tighten knob

with

thrust bearing and races. (Figure 1.) This holds tube into place. You can now put the drum back on the machine.

7

TO INSTALL DRUM

DISCONNECT MACHINE FROM POWER

SOURCE BEFORE INSTALLING

DRUM ON MACHINE!

1. Hang V-Belt from motor pulley. (64” belt for large drum, 57” for small.)

2. Place drum on the machine, positioning the shaft into rear drum clamp first. Rotate the drum until the hole in the shaft fits over the guide pin in the clamp.

3. Then put the distributor tube into the front post clamp.

4. Close front and rear clamps. Then tighten knobs.

5. Slip V-Belt under drum.

Speedrooter 91™

TO INSTALL CABLE IN DRUM

DISCONNECT MACHINE FROM POWER

SOURCE BEFORE INSTALLING

CABLE IN DRUM!

To install cable in the drum, simply connect the male end of the cable to the drum connecting cable, which is already attached to the drum. Then remove the drum V-

Belt and turn the drum clockwise, while pushing cable

Note:

The cable should lay in the drum in a clockwise direction.

MAINTENANCE

DISCONNECT MACHINE FROM POWER

SOURCE BEFORE PERFORMING MAINTE-

NANCE ON MACHINE!

To keep your machine operating smoothly, it is essential that all bearings and distributor tube bushings be lubricated. Oiling moving parts is particularly important where machine comes in contact with sand, grit and other abrasive material.

CABLE MAINTENENCE

To get maximum service from your cables, be sure that they are clean and well oiled. This not only provides running lubrication but greatly extends the life of the cables as well.

Some users periodically pour oil directly into the drum.

Then, as the drum turns, the cables get complete lubrication. Our SNAKE OIL is ideally suited for this purpose, since it not only lubricates the cables, it deodorizes them as well.

FEED MAINTENANCE

Keep feed free of excessive soil and grit. It is recommended that the feed be flushed with fresh water followed by a light oiling of the moving parts. No disassembly is normally required. Failure to feed can usually be traced to the following possibilities:

DIRT ACCUMULATION

Over time, dirt can harden enough to stop roller rotation.

Flushing with water followed by liberal oiling can usually restore function. If disassembly is required, proceed as follows:

1. Remove the feed tension knob, springs and spring plunger. Note the positioning of these parts to ease

8

re-assembly. The top roller can now be removed.

2. Remove the snap rings and thrust washers from the bottom housing cylinders. The bottom rollers can now be removed.

3. Re-assembly is done in reverse order.

DAMAGED ROLLER

Excessive use may wear a roller to the point of failure. It is recommended that all three rollers be replaced at the same time (Cat # PO-703).

TANGLED CABLE

If a cable loops over itself in the drum, it will not feed properly. Remove and reload the cable to restore function. If the cable kinks, it is evidence of abuse and results from the use of too much pressure or use of the wrong size cable for the line. Do not force the cable — let the cutter do the work.

F

OR MORE INFORMATION

CONTACT THE

D

RAIN

B

RAINS

®

AT

:

412-771-6300 or 800-245-6200 www.drainbrain.com

[email protected]

Speedrooter 91™

TROUBLE SHOOTING GUIDE (Table 3)

Problem Probable Cause

Cable kinks or breaks.

Operator forcing the cable.

Solution

Do not force the cable. Let the cutter do the work.

Cable tangles in drum.

Too much slack between machine and drain.

Cable used in wrong size drain line.

Cable exposed to acid.

Operator forcing the cable.

Allow no more than two feet between machine and drain.

A cable that is too large or too small in diameter for a line is more likely to kink. (Consult Table 1—

Cable Applications.)

Clean and oil cables regularly.

Do not force the cable. Let the cutter do the work.

Drum stops while foot pedal depressed.

Machine running in reverse.

Distributor tube frozen.

Hole in pedal or hose.

Hole in diaphragm switch.

Drum turns in one direction but not other.

Reverse switch failure or momentary contact switch.

Do not run the machine in reverse to retract the cable from the drain.

Lubricate distributor tube bushings.

Replace as required.

If no hole found in pedal or hose, replace diaphragm switch.

Replace switch. Note: Momentary contact switch must be held in position to use reverse.

Ground fault circuit interrupter trips and will not reset.

Damaged power cord or extension cord.

Short circuit in motor.

Faulty ground fault circuit interrupter.

Motor turns but drum does not.

Safety Slip Clutch (optional) engaged.

Failure to feed.

Cable tangled in drum.

Replace cords.

Take motor to authorized repair center.

Replace ground fault circuit interrupter.

Do not force cable.

Do not run machine in reverse. Use proper cable size. (Consult Cable Application Chart—Table 1).

Feed misadjusted.

Feed roller frozen.

Worn cable.

If feed tension knob is too loose the cable will slip.

If it is too tight the feed rollers will wear prematurely.

Clean and lubricate feed rollers regularly. Replace worn rollers.

When cable coils wear flat, cable should be replaced.

9

S91-402

S91-404

S91-404-A

S91-405

S91-407

S91-410

S91-410-A

S91-420

S91-421

S91-422

S91-423

S91-424

S91-107-G

S91-107-H

S91-108

S91-108-A

S91-109

S91-109-A

S91-109-B

S91-109-C

S91-110

S91-111

S91-112

S91-115

S91-116

S91-118

S91-118-C

S91-120

S91-120-A

S91-120-D

S91-130

S91-130-A

S91-130-D

S91-400

CAT. NO.

S91-100

S91-101

S91-101-A

S91-101-B

S91-101-C

S91-103

S91-103-A

S91-103-B

S91-107

S91-107-A

S91-107-B

S91-107-C

S91-107-D

S91-107-E

S91-107-F

Speedrooter 91™

Speedrooter 91 Parts List

DESCRIPTION

Frame Complete

Frame Only with Axle

Handle Support Knob (2)

Motor Support Bolt, Nut, & Washer

Cord Wrap Cap (2)

Stair Climber with Belt (1)

Nuts, Bolts, & Washers (2)

Spacers (2)

Plated Handle Assembly

Handle – Left

Handle – Right

6" Handle Wheel

Axle for Handle Wheel

Bushings (2)

Felt Washers (2)

CAT. NO.

S91-425

S91-430

S91-440

S91-440-A

S91-450

S91-452

S91-454

S91-455

S91-460

S91-460-A

S91-470

S91-471

S91-472

DESCRIPTION

Distributor Tube Retaining Bolt

Drum Shaft

Inner Drum Cage

Bushing

Large Drum Complete with Shaft

and Distributor Tube (18")

Drum Shell

Drum Hub Bearings (2)

Bearing Spring

Drum Connecting Cable

(for 5/8" and 3/4" cables)

Nut, Bolt, & Washer

Drum Distributor Tube Assembly

Distributor Tube Only

Bushing

Bolts and Nuts (2)

Set Screws (2)

Brake Rod

Roll Pin

Brake Rod Handle with Knob

Knob for Brake Rod

Roll Pin

Brake Rod Latch with Screws

10" Wheel with Retaining Cap (1)

Wheel Retaining Cap (2)

Wheel Spacer Washers (2)

Axle

Motor Support Spring

Motor Support Platform

Nuts, Bolts, & Washers (4)

Front Bearing Assembly

Front Bearing Knob

Bolts, Nuts & Washers (2)

Rear Drum Shaft Clamp

Drum Clamp Knob

Mounting Bolts & Washers (2)

Small Drum Complete with Shaft

and Distributor Tube (15")

S91-473

S91-474

S91-475

S91-475-A

S91-480

S91-481

S91-482

S91-490

S91-490-A

S91-600

S91-600-3/4

S91-601

S91-602

S91-602-1

S91-603

S91-604

S91-605

S91-605-A

S91-605-B

S91-605-C

Retaining Ring

Thrust Bearing Race

Distributor Tube Retaining Knob

with Bearing Assembly

Bearing Assembly for Retaining Knob

Drum Shaft

Wear Washer

Spacer collar with Set Screw

Inner Drum Cage

Bushing

1/2 hp Motor Complete with Air Foot

Switch, Reverse Switch, & GFCI

3/4 hp Motor Complete with Air Foot

Switch, Reverse Switch, & GFCI

V-Belt (64")

V-Belt Pulley

Slip Clutch (Optional)

Knob for Mounting Stud

20 ft. Power Cord with GFCI

Air Foot Switch & Rev. Switch Assem.

Box Only with Cover & Screws

Foot Pedal and Hose

Cable Tie

Drum Shell

Drum Hub with Bearings

Bushings (2)

Nuts, Bolts, & Washers (5)

Shaft Washer

Drum Connecting Cable (for 1/2" cables)

Nut, Bolt, & Washer

Small Drum Distributor Tube Assem.

Distributor Tube Only

S91-605-E

S91-605-G

S91-605-H

S91-605-J

S91-605-N

S91-609-1/2

S91-609-3/4

S91-614

S91-TB

Power Switch Diaphragm

Reverse Switch – 3-Way

Rubber Boot (Rental)

Barbed Adapter

Strain Relief Nut

Belt Guard (1/2 hp) with Slot

Belt Guard (3/4 hp) with Slot

Small Drum V-Belt (57")

Tool Box

Bushing

Retaining Ring

Thrust Bearing Race

S91-GT

GTE

S91-DECAL

S91-VIDEO

Guide Tube for Speedrooter 91

Guide Tube Extension

Set of Safety Decals

Instructional Video

For Power Feed Parts List and Schematic Diagram please visit www.drainbrain.com.

10

11

Speedrooter 91™

Speedrooter 91™

General Wire Spring Co,

1101 Thompson Avenue

McKees Rocks, PA 15136

412-771-6300

www.drainbrain.com

© General Wire Spring Co. 2009 C-91OI-0409