Badger Meter Europa GmbH BC-2 Batch Controller Operating Instructions

®
Badger Meter Europa GmbH
OPERATING INSTRUCTIONS
Batch Controller BC-2
April 2002
Version BC-2-04/02-e
Content
Content
1.
2.
General
1
1.1
1.2
1
2
2.2
2.3
2.4
4.
5.
System description
Specifications
Set-up
2.1
3.
Page
5
Mounting
2.1.1 Panel mounting
Electrical connections
2.2.1 Inputs
2.2.2 Power and outputs
Switch set-up
Modes of operation
5
5
7
9
10
11
11
Front panel function description
17
3.1
3.2
3.3
Entering of a new prescale value
Entering of a new preset value
Entering of a new time and output value
18
18
19
Hints for applications other than flow metering
20
4.1
20
Some sensor examples
Trouble shooting
21
5.1
5.2
5.3
21
23
23
Self test
Power-up diagnostics
Service address
Operating Instructions ? BC-2-04/02-e
General
Page 1/23
How to set / erase a coma on the BC-2
1.
How to set a coma
1.1
1.2
1.3
2.
How to erase a coma
2.1
2.2
2.3
1.
Press key farthest left and hold
Press key at the desired position and hold
Release first the key on the left, then the key on the desired
position
Press key farthest left and hold
Press key farthest right and hold
Release first the key on the left, then the key on the right
General
The BC 2 is designed for use with a pulse generating flow meter,
manufactured by Badger Meter. Such are oscillating piston meters,
nutating disc meters, turbine meters, pelton wheel meters, oval gear
meters and some special instruments.
If supplied with a flow meter, the BC 2 is programmed and scaled readily
by Badger Meter, according to customers orders. In this case, you need to
read only the chapters marked with a vertical bar for initial set-up and
normal operation. If you want to re-program an instrument, please take
into consideration that it may have been supplied with a "PROGRAMDISABLE" jumper for customers safety.
1.1
System description
The BC 2 consists of a dual preset counter with two relay – and
two transistor outputs, an electronic scaling function ("electronic
gears"), a power supply for the pulse transmitter, display and a
time switch.
Operating Instructions ? BC-2-04/02-e
Specification
1.2
Page 2/23
Specification
1.
2.
3.
4.
Display:
Power requirements:
Sensor power:
Count input:
6 digit, (7,6 mm high LCD display)
230 VAC (+/- 10%). 0/60 Hz, 6 VA
12 VDC (+/- 25%) @ 100 mA
Switch selectable to accept count
pulses from a variety of sources,
including switch contacts, outputs
from CMOS or TTL circuits and all
standard RLC sensors.
If ordered with a meter, count input is set-up correct by
Badger Meter.
Current sourcing
–
Unit provides 3.9 K pull-down load for
sensors with current sourcing outputs.
(Max. input voltage 28 VDC @ 7 mA)
Current sinking
-
Unit provides 7.8 K pull-up load for
sensors with current sinking outputs.
(Max. sensor current 1.6 mA)
Debounce
–
Damping capacitor provided for switch
contact debounce. Limits count speed to
100 pps max. and input pulse width to
5 msec. min.
LO BIAS – Input Trigger levels V IL = 1.5 V V IH = 3.75
HI BIAS – Input Trigger levels V IL = 5.5 V V IH = 7.5V
Note:
Bias levels +/- 10% @ 12 VDC sensor voltage. These
levels vary proportionally with the sensor supply voltage.
5. Prescale value range – 0 to 9.99999
If ordered with a flow meter, K factor is entered by Badger Meter.
6. Maximum count rates: High frequency
The following chart lists the count rates for all the possible
prescale values.
Operating Instructions ? BC-2-04/02-e
Specification
Page 3/23
Prescale value
0,00000 to 1
1,00001 to 2
2,00001 to 3
3,00001 to 4
4,00001 to 5
5,00001 to 6
6,00001 to 7
7,00001 to 8
8,00001 to 9
9,00001 to 9.99999
Count rate
2000 counts/second
1500 counts/second
1300 counts/second
1100 counts/second
1000 counts/second
900 counts/second
800 counts/second
750 counts/second
700 counts/second
650 counts/second
Low frequency
100 cps for switch contact closures.
Note: These units will operate with VCM (E-H) modules.
7. Control inputs
Remote reset
-
Active low (V IL = .5 V max) internally
pulled up to 5 VDC through a 10 KOhm
resistor (I SNK = .5 mA). Response
time = 10 sec. A low will reset the unit
and deactivate outputs.
Program disable
-
Active low (V IL = .5 V max) internally
pulled up to 5 VDC through a 10 KOhm
resistor (I SNK = .5 mA). A low will
inhibit the changing of presets, prescale
and time outputs, as well as testing
outputs in self-test.
Up/Down control -
Active low (V IL = .5 max) internally
pulled up to 5 VDC through a 10Kohm
resistor (I SNK = .5 mA). Response
time = 150 ? sec. This input determines
the direction of the count, and is
independent of reset to zero or reset to
preset modes of operation.
Operating Instructions ? BC-2-04/02-e
Specification
Page 4/23
8. Outputs
Solid state
-
Current sinking NPN open collector
transistors. I SNK = 1000 mA max,
VOH = 30 VDC max. VOL = 1 V @ 100
mA. One solid-state output for each
preset level.
Relays
-
Form C contacts rated 6 amps @
120/260 VAC, 28 VDC (resistive load)
1/8H.P @120 VAC (inductive load). One
relay output for each preset level.
Programmable
timed output
-
The timed output can be programmed
from .01 sec to 99.99 sec, +/- (1% +
10 msec). The timed output is set for 1
sec at the factory.
9. Memory
retention
-
The BC 2 counters have a "no power
EPROM", which maintains all
information when the AC power is
removed. The life expectancy of this
device is at least 10.000 power down
cycles, and length of memory retention
for a single power down can be as long
as 10 years.
10. Input, power
and output
connections -
11. Operating
temperature
range
-
There are two plug-in compression type
barrier strips, located at the rear of the
unit. These strips can be removed form
the rear of the unit for ease of wiring.
After wiring is complete, the connector
can be plugged back into the unit.
0°C to 50°C
Operating Instructions ? BC-2-04/02-e
Specification
Page 5/23
12. Storage
temperature
range
13. Construction
– BC 2a
-
14. Weight
2.
-
-40°C to 70°C
Black plastic front bezel with black
plastic insert. Front panel meets IP65
acc. to DIN, when properly installed.
(Panel gasket and mounting clip
included with unit)
360 g
Set-up
2.1
Mounting
2.1.1
Panel mounting
The BC 2 is designed to be panel mounted with a gasket
to provide a water-tight seal. One mounting clip and two
screws are provided for easy installation. Consideration
should be given to the thickness of the panel. A panel
which is too thin may distort and not provide a watertight seal (recommended minimum panel thickness is 3,2
mm)
Operating Instructions ? BC-2-04/02-e
Mounting
Page 6/23
After the panel cut-out has been completed and deburred,
carefully apply the gasket to the panel. DO NOT APPLY
THE ADHESIVE SIDE OF THE GASKET TO THE COUNTER
BEZEL. Insert the unit into the panel. As depicted in the
drawing, install the two tinnerman nuts and two selftapping screws onto the mounting clip. To install the
mounting clip: hold the mounting clip with both hands, so
that the two corners rest on the index finger of each
hand. While doing this, place the thumb of each hand
over the mounting screws. By pressing on the screws,
flex the clip enough to slide it over the back end of the
case until the clip touches the back of the panel. Insure
that the case is still fully inserted into the panel. While
maintaining slight pressure on th e clip, tighten the two
mounting screws. CATION: Only minimum pressure is
required to seal panel. DO NOT overtighten mounting
screws.
Cut-out
Dimensions in mm
Drawing No. 1
Operating Instructions ? BC-2-04/02-e
Electrical connections
2.2
Page 7/23
Electrical connections
As depicted in drawing no. 2 showing the rear view of the BC 2
counter, there are two terminal blocks, where all wiring
connections are made. Remove the blocks for easy access to the
terminal screws. To remove, insert a screwdriver into one of the
slots on the underside of the block and twist. The block can then
be lifted off the pins for wiring. CAUTION: Terminal blocks should
not be removed with power applied to the unit. For the solid-state
outputs, a three-pin connector is supplied. NOTE: The solid-state
connector housing is polarized to the body of the bottom terminal
block and must be inserted properly.
Drawing No. 2
All the input connections are made to the top 6-terminal block
(labelled TBA). The power and relay output connections are made
to the bottom 8-terminal block (labelled TBB), and the solid-state
outputs are connected to the three-pin connector. (The input
connections are the same for one or two preset counters.)
Operating Instructions ? BC-2-04/02-e
Electrical connections
Page 8/23
Drawing No. 3
Operating Instructions ? BC-2-04/02-e
Inputs
Page 9/23
2.2.1
Inputs
Terminal 6 on TBA (the first terminal from left) is the DC
OUT (+12 V) terminal. This is for sensor supply and can
provide up to 100 mA of current. Terminal 5 is the
COMM (common) terminal, which is the common line to
which the sensor and other input commons are
connected. (Do NOT connect relay commons or solidstate output commons to this point.) Terminal 4 is the
CNT.IN (count input) terminal. When the signal at this
terminal is pulled low (zero volt), a count will be
registered. (See Count Input and Count Rates under the
specifications section.) Terminal 3 is the UP/DN (count
direction control) terminal. When this terminal is at a high
level, the count direction is "UP". When the terminal is
grounded, the count direction is "DOWN". Terminal 2 is
the PGM.DIS (program disable) terminal. When this
terminal is at a high level, the preset values, prescale
value and timed output value(s) can be changed using the
front panel buttons. (Outputs can also be tested using
self-test under this condition. See self-test description for
further details.) When terminal 2 is at a low level
(connected to COMM.) changing these values and testing
the output is no longer possible. Terminal 1 is the
RMT.RST (remote reset) terminal. When this terminal is
at a low level (connected to COMM.), the unit will reset,
and the outputs will run off (if activated). As long as reset
is low, the unit is held at reset.
Then connecting and installing the input wires, the
following guidelines should be followed. (This is especially
true of "electrically noisy" environments.)
A. Never run count and control signal leads in the same
conduit or race ways with conductors feeding
motors, solenoids, SCR controls, heaters, etc. Ideally,
signal wires should be run by themselves in a
separate conduit.
B. Signal leads within electrical enclosures should be
routed as far from contactors, motor starters, control
relay, transformers and other similar components as
possible.
Operating Instructions ? BC-2-04/02-e
Inputs
Page 10/23
C. When shielded wire is used, connect the shield to the
signal common terminal of the BC 2 counter and
leave the other end of the shield unconnected and
insulated from machine ground.
2.2.2
Power and outputs
As mentioned before, power and output connections are
made to the bottom terminal block (labelled TBB), and
the solid-state output connector (located at the lower
right corner of the unit). Primary AC power is connected
to terminals 1 and 2 (marked A.C. Power, located on the
left-hand side of the terminal block TBB). For best results,
the AC power should be relatively "clean" and within the
specified +/- 10% variation limits. Drawing power from
heavily loaded circuits, or from circuits that also power
loads that cycle on and off, should be avoided.
Terminals 3, 4 and 5 are used to connect to output relay
1. Terminal 3 is the normally closed contact. Terminal 4 is
the normally open contact, and terminal 5 is the output
relay common. Terminals 6, 7 and 8 (dual preset only) are
used to connect to output relay 2. Terminal 6 is the
normally closed contact. Terminal 7 is the normally open
contact, and terminal 8 is the output relay common.
The solid-state output connector has three wires (two
wires for the single preset unit) coming from the top of
the connector housing. The yellow wire (first wire as
viewed from the back of the unit) is for solid-state output
1 (labelled 01 SNK.). This internally connects to an NPN
open collector transistor. The black wire is the common
for the solid-state outputs. This terminal should NOT be
used as the common for the input or control terminals.
The blue wire is used to connect to solid-state output 2
(labelled 02 SNK.).
Operating Instructions ? BC-2-04/02-e
Switch set-up
2.3
Page 11/23
Switch set-up
S1 –
SNK.:
SRC.:
S2 –
HI FRQ.:
LO FRQ.:
S3 –
HI BIAS:
LO BIAS:
S4 –
2.4
DIS.RST.:
EN-RST.:
Provides a 7.8K pull-up resistor for sensor with
sinking outputs.
Provides a 3.9K pull-down resistor for sensors
with sourcing outputs.
Removes damping capacitor and allows
operation up to the high speed count
specifications.
Connects damping capacitor for switch contact
debounce. Limits count speed to 100 cps.
Minimum count ON/OFF times – 5 msec.
Sets input trigger levels at mid-range, to
accept outputs from 2-wire proximity sensors,
resistive photo-cells, and logic pulses with full
1 to +12 V swings. (V IL = 5,5 V, V IH = 7,5
V)
Sets input trigger levels to the low range, to
accept logic pulses with 0 to +5 V swings. (V
IL = 1,5 V, V IH = 3.75 V
Disables front panel reset
Enables front panel reset.
Modes of operation
Mode settings of the switches are shown below. The mode
number corresponds to a binary code, represented by the DIP
switch positions. When the switch is "UP", it is equivalent to a
zero. When the switch is "DOWN, it is equivalent to a one. The
mode switch settings can be easily observed from the front panel
by using the self-test. At the end of the self-test, the state of
these mode switches is displayed. The mode selection DIP
switches are located along the side of the unit's case.
Operating Instructions ? BC-2-04/02-e
Modes of operation
Page 12/23
NOTES:
1) For all the following modes of operation, when the unit is set
for a Reset to Zero mode, the UP/DN terminal (count
direction) is normally left high (in "UP" position). When the
unit is set for a Reset to Preset mode, the UP/DN terminal is
normally tied to common (in the "DOWN" position).
However, even though these are the usual conditions for the
UP/DN terminal, it does not have to operate in this fashion
(i.e. the unit can count down in a Reset to Zero mode, or
count up in a Rest to Preset mode, and still maintain normal
operating functions).
2) The timed output must be less than the time required to
count from the reset condition to the preset point. Otherwise,
the output will appear to be latched-on.
MODE 0: Latch outputs at presets, manual reset to zero
In this mode, as the unit counts form zero, output 1 will latch on
when preset 1 is reached, and output 2 will latch on when preset
2 is reached. When a manual reset* occurs, the unit will reset to
zero and the outputs, if latched on, will unlatch. Counts will
continue to accumulate after the outputs have turned on.
MODE 1: Timed outputs at presets, manual reset to zero
In this mode, as the unit counts from zero, output 1 will turn on
when preset 1 is reached, and output 2 will turn on when preset 2
is reached. The outputs will turn off after their respective
programmed time values have occurred. When a manual reset
occurs, the unit will reset to zero. Manual reset* will terminate
the timed outputs if the outputs are still turned on. Counts will
continue to accumulate after the preset levels have been reached.
MODE 2: Output 1 turn off at preset 2, latch output 2 at preset
2, manual reset to zero
In this mode, as the unit counts from zero, output 1 will turn on
when preset 1 is reached. When preset 2 is reached, output 2 will
turn on and output 1 will turn off. Output 2 will remain latched on
until a manual reset occurs. Manual rest* will turn off both
outputs and the unit will reset to zero. Counts will continue to
accumulate after the preset levels have been reached.
Operating Instructions ? BC-2-04/02-e
Modes of operation
Page 13/23
MODE 3: Output 1 turn off at preset 2, timed output 2 at preset
2, manual reset to zero
In this mode, as the unit counts from zero, output 1 will turn on
when preset 1 is reached. When preset 2 is reached, output 2 will
turn on and output 1 will turn off. Output 2 will turn off after its
programmed time value has occurred. When a manual reset
occurs, the unit will reset to zero. Manual reset* will turn off both
outputs if they are still activated. Counts will continue to
accumulate after preset levels have been reached.
MODE 4: Output 1 turn off at preset 2, timed output 2 at preset
2, automatic reset to zero at preset 2
In this mode, as the unit counts from zero, output 1 will turn on
when preset 1 is reached. When preset 2 is reached, output 2 will
turn on, output 1 will turn off, and the unit will automatically
reset to zero. Output 2 will turn off after its programmed time
value has occurred. Manual reset* will turn off both outputs, if
activated, and reset the count to zero. During automatic reset, no
counts will be lost if the count rate does not exceed the maximum
count rate specified.
MODE 5: Timed outputs at presets, automatic reset to zero at
preset 2
In this mode, as the unit counts from zero, output 1 will turn on
when preset 1 is reached, and output 2 will turn on when preset 2
is reached. The outputs will turn off after their respective
programmed time values have occurred. Also, when preset 2 is
reached, the unit will automatically reset the count to zero and
start the cycle over (output 2 will remain on until its time value
has occurred). Manual reset* will turn off both outputs and reset
the count to zero. During automatic reset, no counts will be lost if
the count rate does not exceed the maximum count rate specified.
Operating Instructions ? BC-2-04/02-e
Modes of operation
Page 14/23
MODE 6: Output 1 turn off at preset 2, timed output 2 at preset
2, automatic reset to zero after timed output 2
In this mode, as the unit counts from zero, output 1 will turn on
when preset 1 is reached. When preset 2 is reached, output 2 will
turn on and output 1 will turn off. Output 2 will turn off after its
programmed time value has occurred. At the end of timed output
2, the unit will automatically reset to zero and start the cycle over
again. During automatic reset, no counts will be lost if the count
rate does not exceed the maximum count rate specified. Manual
reset* will turn off both outputs, if turned on, and reset the count
to zero.
MODE 7: Timed outputs at presets, automatic reset to zero after
timed output 2
In this mode, as the unit counts from zero, output 1 will turn on
when preset 1 is reached, and output 2 will turn on when preset 2
is reached. The outputs will turn off after their respective
programmed time values have occurred. At the end of timed
output 2, the unit will automatically reset to zero and start the
cycle over again. During automatic reset, no counts will be lost, if
the count rate does not exceed the maximum count rate specified.
Manual reset* will turn off both outputs, if turned on, and reset
the count to zero.
MODE 8: Latch output at preset 1 and zero, manual reset to
preset 2
In this mode, as the unit counts from preset 2, output 1 will latch
on when preset 1 is reached, and output 2 will latch on when zero
is reached. When a manual reset* occurs, the unit will reset to
preset 2 and the output, if latched on, will unlatch. Counts will
continue to register after the outputs have turned on.
MODE 9: Timed output at preset 1 and zero, manual reset to
preset 2
In this mode, as the unit counts from preset 2, output 1 will turn
on when preset 1 is reached, and output 2 will turn on when zero
is reached. The outputs will turn off after their respective
programmed time values have occurred. When a manual reset*
occurs, the unit will reset to preset 2. Manual reset will terminate
the timed outputs if the outputs are still activated. Counts will
continue to accumulate after the outputs have activated.
Operating Instructions ? BC-2-04/02-e
Modes of operation
Page 15/23
MODE 10: Output 1 turn off at zero, latch output 2 at zero,
manual reset to preset 2
In this mode, as the unit counts from preset 2, output 1 will turn
on when preset 1 is reached. When zero is reached, output 2 will
turn on and output 1 will turn off. Output 2 will remain latched on
until a manual reset occurs. Counts will continue to accumulate
after preset levels have been reached. Manual reset* will turn off
all outputs, if activated, and the unit resets to preset 2.
MODE 11: Output 1 turn off at zero, timed output 2 at zero,
manual reset to preset
In this mode, as the unit counts from preset 2, output 1 will turn
on when preset 1 is reached. When zero is reached, output 2 will
turn on and output 1 will turn off. Output 2 will turn off after its
programmed time value has occurred. Counts will continue to
accumulate after the preset levels have been reached. When a
manual reset* occurs, the unit will reset to preset 2. Manual reset
will also turn off both outputs, if still activated.
MODE 12: Output 1 turn off at zero, timed output 2 at zero,
automatic reset to preset 2 at zero
In this mode, as the unit counts from preset 2, output 1 will turn
on when the preset is reached. When zero is reached, output 2
will turn on, output 1 will turn off, and the unit will automatically
reset to preset 2. Output 2 will turn off after its programmed time
value has occurred. Manual reset* will turn off both outputs, if
turned on, and reset the count to preset 2. During automatic
reset, no counts will be lost if the count rate does not exceed the
maximum specified count rate.
Operating Instructions ? BC-2-04/02-e
Modes of operation
Page 16/23
MODE 13: Timed outputs at preset 1 and zero, automatic reset to
preset 2 at zero
In this mode, as the unit counts from preset 2, output 1 will turn
on when preset 1 is reached, and output 2 will turn on when zero
is reached. The outputs will turn off after their respective
programmed time values have occurred. Also, when zero is
reached, the unit will automatically reset the count to preset 2
and start the cycle over (output 2 will remain on until its time
value has occurred). Manual reset* will turn off both outputs, if
turned on, and reset the count to preset 2. During automatic
reset, no counts will be lost if the count rate does not exceed the
maximum count rate specified.
MODE 14: Output 1 turn off at zero, timed output 2 at zero,
automatic reset to preset 2 after timed output 2
In this mode, as the unit counts from preset 2, output 1 will turn
on when preset 1 is reached. When zero is reached, output 2 will
turn on and output 1 will turn off. Output 2 will turn off after its
programmed time value has occurred. At the end of timed output
2, the unit will automatically reset to preset 2 and start the cycle
over. During automatic reset, no counts will be lost if the count
rate does not exceed the maximum count rate specified. Manual
reset* will turn off both outputs, if activated, and reset the count
to preset 2.
MODE 15: Timed outputs at preset 1 and zero, automatic reset to
preset 2 after timed output 2
In this mode, as the unit counts from preset 2, output 1 will turn
on when preset 1 is reached, and output 2 will turn on when zero
is reached. The outputs will turn off after their respective
programmed time values have occurred. At the end of timed
output 2, the unit will automatically reset to preset 2 and start
the cycle over. During automatic reset, no counts will be lost if the
count rate does not exceed the maximum specified count rate.
Manual reset* will turn off either output, if turned on, and reset
the count to preset 2.
* - Manual reset, either by front panel reset (if enabled) of
remote reset, is always active and will override any present
condition or state of the counter.
Operating Instructions ? BC-2-04/02-e
Front panel function description
3.
Page 17/23
Front panel function description
These units employ eight front panel buttons for control and data entering.
The button functions are as described below:
Drawing No. 4
Reset "R"
This button resets the counter to either zero or preset, depending on the
mode of operation selected. For this button to operate, the en able/disable
reset button switch at the rear of the unit must be set to the enable (EN.)
position. This button is also used, in conjunction with the two preset
buttons (one button on the single preset unit), to view and change the
timed output value. When reset is activated, all processes are stopped or
interrupted (i.e. outputs turn off, display is halted, etc.). This is the case
under any mode of operation, in any data entry mode.
Preset "P1" and P2"
The preset buttons are labelled, and are the two right-hand buttons of the
top two rows, located on the front of the unit. When the "P1" button is
pressed, preset 1 is displayed and the "Preset Enter" mode is accessed.
(See "To Enter A New Preset Value".) These values will remain displayed
for approximately 10 sec. after release of the button. The preset buttons
are also used, in conjunction with the reset button, to view and change the
timed output values. (See "To Enter A New Timed Output Value" section.)
Enter "E"
This button is used in the "Preset Enter" mode and in the "Timed Output
Enter" mode. After the desired value is obtained on the display, this button
is pressed. This enters the value into the internal processor. This new
value, at that instant, is used in the processing of preset or timed output
values "E" can also be used at the end of self-test to exit self-test.
Operating Instructions ? BC-2-04/02-e
Front panel function description
Page 18/23
Prescale "PS"
When the "PS" button is pressed, the prescale value is displayed and the
"Prescale Enter" mode is accessed. (See "To Enter A New Prescale
Value".) This value will remain displayed for approximately 10 sec. after
release of the button.
3.1
To enter a new prescale value
1. Press "PS". This will display the prescale value and it will
remain displayed for approximately 10 sec. after release of
the button. (At this time, the prescale display mode can be
exited without change by pressing the "E" button.)
2. Once the prescale value is displayed, changing the digit value
can be done by pressing the button directly beneath the digit
position to be changed. (To change this value, "PGB.DIS."
must be at a high level.) Each time the button is pressed, the
digit will increment by one. Also, pressing and holding the
button down will continuously scroll the digit from 0 through
9, then back to 0 again. When the desired value for that digit
is reached, release the button. Do this for all the digits to be
changed.
3. Press the "E" (Enter) button to enter the value into the unit's
memory. AS SOON AS the "E" button is pressed, this new
value is used as the operating data. If the "E" button is not
pressed within 10 sec. after the last digit has been changed,
the value will disappear (go back to normal display mode) and
continue to operate on the previous value.
3.2
To enter a new preset value
1. Press "P1" (or "P2", if a two preset unit). This will display
the respective preset value and it will remain displayed for
approximately 10 sec. after release of the last button pushed.
(At this time, the preset display mode can be exited, without
a change, by pressing the "E" button.)
Operating Instructions ? BC-2-04/02-e
Front panel function description
Page 19/23
2. Once the preset value is displayed, changing the digit value
can be done by pressing the button directly beneath the digit
to be changed. (To change this value, "PGM.DIS." must be at
a high level.) Each time the button is pressed, the digit will
increment by one. Also, pressing and holding the button down
will continuously scroll the digit from 0 through 9, then back
to 0 again. When the desired value for that digit is reached,
release the button. Do this for all the digits to be changed.
3. Press the "E" (Enter) button to enter the value into the unit's
memory. AS SOON AS the "E" button is pressed, this new
value is used as the operating data. This means, if the preset
value is entered, and the old or new value has not been
reached, the new value will be used without process
disruption. (Preset on the fly.) If the "E" button is not pressed
within 10 sec. after the last digit has been changed, the value
will disappear (go back to normal display mode) and the unit
will continue to operate on the previous value. During the
displaying, changing and entering of a new preset value, all
functions of the unit are operational (i.e. counting, resetting,
outputs firing, etc.).
3.3
To enter a new timed output value
1. Press and hold the button and then press the "R" (Reset)
button. The respective timed output value will now be
displayed and will remain displayed for approximately 10 Sec.
after release of the button pushed. (At this time, the timed
output display mode can be exited, without change, by
pressing the "E" button.)
2. Once the timed output is displayed, changing the digit value
can be done by pressing the button directly beneath the digit
to be changed. (To change this value, "PGM.DIS" must be at
a high level.) Each time the button is pressed, the digit will
increment by one. Also, pressing and holding the button down
will continuously scroll the digit from 0 through 9, then back
to 0 again. When the desired value for that digit is reached,
release the button. Do this for all the digits to be changed.
(This value can be set between 0,01 Sec. and 99,99 Sec.)
Operating Instructions ? BC-2-04/02-e
Front panel function description
Page 20/23
3. Press the "E" (Enter) button to enter the value into the unit's
memory. AS SOON AS the "E" button is pressed, this new
value is used as the operating data. If the "E" button is not
pressed within 10 Sec. after the last digit has been changed,
the value will disappear (go back to normal display mode) and
the unit will continue to operate on the previous value. During
the displaying, changing and entering of a new timed output
value, all functions of the unit are operational (i.e. counting,
resetting, output firing, etc.).
4.
Hints for applications other than flow metering
Badger Meter uses BC 2 as a useful complement to their range of flow
meters. The design of BC 2 also allows a lot of other industrial counting
applications. Please check specifications (1.2) before trying an application
not mentioned in this manual.
4.1
Some sensor examples
Drawing No. 5
Operating Instructions ? BC-2-04/02-e
Hints for applications
Page 21/23
Notes:
1. Sensor supply voltage and current
The +12 V sensor supply voltage on the "DC OUT" terminal
is nominal with +/- 25% variation due to line and internal
load variations. All RLC sensors will accommodate this
variation.
2. HI/LO FRQ selection
The HI/LO FRW selection switch must be set on LO FRQ when
switch contacts are used to generate count input signals.
Since the LO FRQ mode also provides very high immunity
against electrical noise pickup, it is recommended that his
mode also be used, whenever possible, with electronic sensor
outputs, as added insurance. The LO FRQ mode can be used
with any type of sensor output, provided count pulse widths
never decreases below 5 milliseconds, and the count rate
does not exceed 100 cps.
3. V IL and V IH levels given are nominal values, +/- 10% when
counter voltage on "DC OUT" terminals is +12 VDC. These
nominal values will vary in proportion to the variations in "DC
OUT" terminal voltage, caused by line voltage and load
changes.
4. When shielded cable is used, the shield should be connected
to COMM at the counter and left unconnected at sensor end.
5.
Trouble shooting
5.1
Self-test
This unit has a built-in self-test feature, which can be activated
without loosing counts or preset values, missing preset points or
timed output durations, or interfering with control functions. With
this test, all digits are cycled though, then the mode select switch
settings are displayed. At this point, the outputs can also be
tested.
Operating Instructions ? BC-2-04/02-e
Self-test
Page 22/23
To enter self-test, the two left-hand digit buttons (located on the
front panel) simultaneously. At this time, whatever count value
was displayed will disappear and be replaced by a string of six
zeros. This will be shown for about a half a second, then a string
of ones will appear for the same time duration. Following these, a
string of twos and so on, up to none will be displayed. After the
nines are shown, five decimal points will appear. After this
portion, an interlace pattern of 1, 0, 1, 0, 1, 0 then 1, 2, 1, 2, 1, 2
and so on, until all digits from zero to nine have been displayed.
The next portion of self-test will display a group of ones and zeros.
These ones and zeros are the settings of the mode select switches
(the four DIP switches located along the side of the unit). This
pattern directly corresponds to the number representing the mode
of operation. If the switches are changed at his point of self-test,
the settings can be seen to change. These changes will not affect
counter operation immediately, but any changes will take effect
when self-test is exited. When the switch is "DOWN", the LCD
will show a one. When the switch is "UP", the LCD will show a
zero. If no testing of the output is required, press the "E" button
until the unit exits self-test (the unit will go back to the count
display mode). Also, if no activity occurs on the switches or the
front panel button within 18 sec, after the unit pauses at the
mode switch display, the unit will automatically exit the self-test.
During the time the mode switch settings are displayed, the
outputs can be tested. To activate the output, press the "P1"
"P2" button.
Note:
The "PGM:DIS" terminal must be at a high level for the outputs to
be activated. Also, caution should be used when testing the
outputs, so as not to cause any undesirable or hazardous
conditions in the system. (To turn off the outputs, release the
button.)
If the outputs are not tested, the state(s) of the outputs will
remain the same as they were prior to self-test. If the outputs are
tested in self-test, the outputs will be off after exiting self-test.
Operating Instructions ? BC-2-04/02-e
Self-test
Page 23/23
Rapid advantage of the self-test routine can be done by pressing
and releasing any of the front panel buttons except for the "R"
button. (Pressing "R" at any time, except when entering the
timed output mode, will reset the unit.)
5.2
Power-up diagnostics
The BC 2 has internal diagnostics, which will check the stored
data during power-up. When the data is saved (power-down),
computations are made with these values. The results of these
computations are stored in the memory to serve as a check
against possible error. On power-up, these same computations are
repeated on the stored data. If these results do not agree with the
stored results, then a "P" will appear on the right side of the
display. Normal operation of the unit will continue while this "P"
is displayed. To remove the "P" from the display, press the "E"
button. Then check programmed values to be certain they are
correct.
5.3
Service address
There are no user serviceable parts inside. If necessary, address to
your local agent or to Badger Meter Europa GmbH for further
service.
Operating Instructions ? BC-2-04/02-e
Hotline
Tel.
Fax
®
+49-7025-9208-0 or -31
+49-7025-9208-15
Badger Meter Europa GmbH
Subsidiary of Badger Meter, Inc.
Karlstrasse 11
72660 Beuren (Germany)
E-mail: [email protected]
Operating Instructions ? BC-2-04/02-e
">