advertisement
TD360_01-35 02.2.13 9:57 AM Page 1
OWNER’S
MANUAL
19-INCH COLOR TV/DVD/VHS
6719DB1
This Owner’s Manual is made of recycled paper.
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
SUPPLIED ACCESSORIES
ACCESSORIES
Remote Control Unit
Batteries
PART NO.
N0288UD
2 AA Batteries
If you need additional operating assistance after reading this owner’s manual or to order replacement accessories, please call
TOLL FREE : 1-800-968-3429.
Please read before using this equipment
TD360_01-35 02.2.13 9:57 AM Page 2
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSON-
NEL.
The caution marking is located on the rear of the cabinet.
THIS SYMBOL INDICATES THAT DAN-
GEROUS VOLTAGE CONSTITUTING A
RISK OF ELECTRIC SHOCK IS PRESENT
WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE
ARE IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THE
APPLIANCE.
IMPORTANT SAFEGUARDS
1.Read instructions-All the safety and operating instructions should be read before the appliance is operated.
2.Retain Instructions-The safety and operating instructions should be retained for future reference.
3.Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to.
4.Follow Instructions-All operating and use instructions should be followed.
5.Cleaning-Unplug TV/DVD/VHS from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5.
6.Attachments-Do not use attachments not recommended by the TV/DVD/VHS manufacturer as they may cause hazards.
7.Water and Moisture-Do not use this TV/DVD/VHS near water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.
8.Accessories-Do not place this TV/DVD/VHS on an unstable cart, stand, tripod, bracket, or table. The TV/DVD/VHS may fall, causing serious injury to someone, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the
TV/DVD/VHS. Any mounting of the appliance should follow the
PORTABLE CART WARNING manufacturer’s instructions and should use a mounting accessory recommended by the manufacturer.
An appliance and cart combination should be moved with care.Quick
stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
S3126A
- 2 -
AMEUBLES- Cet appareil ne doit
être placé que sur un meuble (avec ou sans roulettes) recommandé par le fabricant. Si vous l’installez sur un meuble à roulettes, déplacez les deux ensembles avec précaution.
Un arrêt brusque, l’utilisation d’une force excessive et des surfaces irrégulières risquent de déstabiliser l’ensemble et de le renverser.
SYMBOLE D'AVERTISSEMENT POUR
LES COMPOSANTES
APPAREIL ET MEUBLE A ROULETTES
S3126A
9. Ventilation-Slots and openings in the cabinet and the back or bottom are provided for ventilation and to ensure reliable operation of the TV/DVD/VHS and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the
TV/DVD/VHS on a bed, sofa, rug, or other similar surface.
This TV/DVD/VHS should never be placed near or over a radiator or heat register. This TV/DVD/VHS should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
10.Power Sources-This TV/DVD/VHS should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For TV/DVD/VHSs intended to operate from battery power, or other sources, refer to the operating instructions.
11.Grounding or Polarization-This TV/DVD/VHS is equipped with a polarized alternating-current line plug(a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
12.Power-Cord Protection-Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.
EN
1B15
TD360_01-35 02.2.13 9:57 AM Page 3
F IGUR E A
EXAMPLE OF ANTENNA GROUNDING AS PER
NA TIONA L ELECT RIC AL CODE
AN TE NN A
L E A D I N
W I R E
GROUN D
C L A M P
A NTEN NA
DI S CHA RG E UN I T
(NEC SE CTI ON 8 10 -2 0)
E L E CT RI C
S E RV I CE
E Q U I P M E N T
S 2 8 9 8 A
NE C - NA TI O NAL EL E CTRI CAL CO DE
G RO UNDI NG CO NDUCT ORS
(NEC SE CTI ON 8 10 -2 1)
G RO UND CL AM PS
P OWE R S E RVI C E G RO UNDI NG
E L E C TR O DE S Y S T E M
(NEC A RT 2 50 , P ART H)
13.Outdoor Antenna grounding-If an outside antenna or cable system is connected to the TV/DVD/VHS, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig. A)
14.Lightning-For added protection for this TV/DVD/VHS receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system.
This will prevent damage to the TV/DVD/VHS due to lightning and power-line surges.
15.Power Lines-An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
16.Overloading-Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.
17.Object and Liquid Entry-Never push objects of any kind into this TV/DVD/VHS through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the TV/DVD/VHS.
18.Servicing-Do not attempt to service this TV/DVD/VHS yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
19.Damage Requiring Service-Unplug this TV/DVD/VHS from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged or frayed.
b. If liquid has been spilled, or objects have fallen into the
TV/DVD/VHS.
c. If the TV/DVD/VHS has been exposed to rain or water.
d. If the TV/DVD/VHS does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the TV/DVD/VHS to its normal operation.
e. If the TV/DVD/VHS has been dropped or damaged in any way.
f. When the TV/DVD/VHS exhibits a distinct change in performance-this indicates a need for service.
20.Replacement Parts-When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, injury to persons or other hazards.
21.Safety Check-Upon completion of any service or repairs to this TV/DVD/VHS, ask the service technician to perform routine safety checks to determine that the TV/DVD/VHS is in proper operating condition.
22.Heat-This TV/DVD/VHS product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE
LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
- 3 EN
1B15
TD360_01-35 02.2.13 9:57 AM Page 4
IMPORTANT COPYRIGHT INFORMATION
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.
FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
RADIO-TV INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
PRECAUTIONS
LASER SAFETY
This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury.
CAUTION: USE OF CONTROLS OR ADJUST-
MENTS OR PERFORMANCE OF PROCE-
DURES OTHER THAN THOSE SPECIFIED
HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
CAUTION: VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN AND INTERLOCK
DEFEATED. DO NOT STARE INTO BEAM.
LOCATION: INSIDE, NEAR THE DECK
MECHANISM.
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC
ÉLECTRIQUES, INTRODUIRE LA LAME LA
PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE
ET POUSSER JUSQU’AU FOND.
- 4 EN
1B15
TD360_01-35 02.2.13 9:57 AM Page 5
LOCATION
For safe operation and satisfactory performance of your TV/DVD/VHS, keep the following in mind when selecting a place for its installation:
•
Shield it from direct sunlight and keep it away from sources of intense heat.
•
Avoid dusty or humid places.
•
Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes at the top and bottom of the unit. Do not place the unit on a carpet because this will block the ventilation holes.
•
Install unit in a horizontal position.
•
Avoid locations subject to strong vibration.
•
Do not place the TV/DVD/VHS near strong magnetic fields.
•
Avoid moving TV/DVD/VHS to locations where temperature differences are extreme.
WARNING
Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, or after heating a cold room or under conditions of high humidity. If a DVD is played in a TV/DVD/
VHS which has moisture, it may damage the DVD and TV/DVD/VHS. Therefore when the condensation occurs inside the unit, turn the POWER button on and allow at least 2 hours for the unit to dry out.
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE
•
Do not handle the power cord with wet hands.
•
Do not pull on the power cord when disconnecting it from an AC wall outlet. Grasp it by the plug.
•
If, by accident, water is spilled on your unit, unplug the power cord immediately and take the unit to our
Authorized Service Center for servicing.
•
Do not put your fingers or objects into the
TV/DVD/VHS disc loading tray.
•
Do not place anything directly on top of the unit.
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.
The serial number of this product may be found on the back of the unit. No other TV/DVD/VHS has the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
- 5 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 6
C
IMPORTANT SAFEGUARDS . . . . .2
C
PRECAUTIONS . . . . . . . . . . . . . . . .4
LOCATION . . . . . . . . . . . . . . . . . . .5
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE .5
WARNING . . . . . . . . . . . . . . . . . . . .5
C
FEATURES . . . . . . . . . . . . . . . . . . . .7
C
OPERATING CONTROLS AND
FUNCTIONS . . . . . . . . . . . . . . . . . . .9
C
PREPARATION FOR USE . . . . . . .11
ANTENNA/CABLE
CONNECTIONS . . . . . . . . . . . . . . .11
CONNECTING TO EXTERNAL
INPUT JACKS . . . . . . . . . . . . . . . .12
INSTALLING THE BATTERIES . .12
EXTERNAL INPUT MODE . . . . . .12
CONNECTING TO A DOLBY
DIGITAL DECODER,
DTS DECODER, OR MPEG
DECODER (for DVD) . . . . . . . . . .13
CONNECTING TO A STEREO
SYSTEM (for DVD) . . . . . . . . . . . .14
CONNECTING TO AN AMPLIFIER
EQUIPPED WITH DIGITAL INPUT
JACKS SUCH AS MD DECK OR
DAT DECK (for DVD) . . . . . . . . . .14
C
SET UP FOR USE . . . . . . . . . . . . .15
CHANNEL SET UP
FOR THE FIRST TIME . . . . . . . . .15
DELETING (OR ADDING)
CHANNEL . . . . . . . . . . . . . . . . . . .15
CHANNEL SET UP AGAIN . . . . . .16
SELECTING THE LANGUAGE . .16
DAYLIGHT-SAVING TIME . . . . . .16
CLOCK SET UP
(AUTO / MANUAL) . . . . . . . . . . . .17
TV/VCR SECTION
C
TV OPERATION . . . . . . . . . . . . . . .19
WATCHING A TV PROGRAM . . .19
DEGAUSSING . . . . . . . . . . . . . . . .19
PICTURE CONTROL . . . . . . . . . . .19
CLOSED CAPTION SYSTEM . . . .20
V-CHIP SET UP . . . . . . . . . . . . . . .21
C
MTS(Multi-Channel Television sound)SYSTEM . . . . . . . . . . . . . . . .23
CHECKING THE SELECTED
MTS MODE . . . . . . . . . . . . . . . . . .23
MTS RECORDING/MONITOR
MODE . . . . . . . . . . . . . . . . . . . . . .23
SELECTING THE MTS SYSTEM .24
C
VIDEO CASSETTE . . . . . . . . . . . . .25
C
PLAYBACK . . . . . . . . . . . . . . . . . . .26
NORMAL PLAYBACK . . . . . . . . .26
TABLE OF CONTENTS
TRACKING ADJUSTMENT . . . . .26
SLOW MOTION . . . . . . . . . . . . . .26
PICTURE SEARCH . . . . . . . . . . . .26
STILL PICTURE . . . . . . . . . . . . . .26
VERTICAL HOLD CONTROL . . .26
C
SPECIAL PLAYBACK . . . . . . . . . .27
RENTAL PLAYBACK . . . . . . . . . .27
AUTO REPEAT PLAYBACK . . . . .27
C
SEARCH . . . . . . . . . . . . . . . . . . . . .28
ZERO RETURN . . . . . . . . . . . . . . .28
TIME SEARCH . . . . . . . . . . . . . . .28
INDEX SEARCH . . . . . . . . . . . . . .29
C
SPECIAL FEATURES . . . . . . . . . .29
REAL TIME TAPE COUNTER . . .29
AUTO REWIND-EJECT . . . . . . . .29
C
RECORDING . . . . . . . . . . . . . . . . .30
NORMAL RECORDING . . . . . . . .30
SKIPPING UNWANTED SCENES
DURING
RECORDING . . . . . . . . . . . . . . . . .30
OTR (One Touch Recording) . . . . . .31
COPYING A VIDEO CASSETTE
(Requires a VCR or camcorder) . . .31
C
TIMER . . . . . . . . . . . . . . . . . . . . . .32
AUTOMATIC
TIMER RECORDING . . . . . . . . . .32
TIMER PROGRAM EXTENSION .33
HINTS FOR AUTOMATIC TIMER
RECORDING . . . . . . . . . . . . . . . . .34
AUTO RETURN . . . . . . . . . . . . . . .34
SLEEP TIMER . . . . . . . . . . . . . . . .34
C
ON SCREEN DISPLAY . . . . . . . . .35
C
CABLE CHANNEL
DESIGNATIONS . . . . . . . . . . . . . .35
DVD SECTION
C
ABOUT THE DISCS . . . . . . . . . . . .36
PLAYABLE DISCS . . . . . . . . . . . .36
DISC TYPES . . . . . . . . . . . . . . . . .36
SYMBOLS USED IN
THIS MANUAL . . . . . . . . . . . . . . .36
C
PLAYING A DISC . . . . . . . . . . . . . .37
PLAYING A DVD VIDEO OR AN
AUDIO CD . . . . . . . . . . . . . . . . . . .36
USING THE DVD MENUS . . . . . .36
USING THE TITLE MENU . . . . . .36
RESUMING PLAYBACK
FROM THE POINT WHERE
PLAYBACK STOPPED . . . . . . . . .38
FAST FORWARD/REVERSE . . . . .38
PAUSING PLAYBACK OR DIS-
PLAYING
A STILL PICTURE . . . . . . . . . . . . .38
STEPPING THROUGH FRAMES .38
SLOW MOTION . . . . . . . . . . . . . .39
PLAYING FROM A DESIRED
TITLE OR CHAPTER . . . . . . . . . .39
STARTING FROM A DESIRED
TIME COUNT . . . . . . . . . . . . . . . . .39
STARTING FROM A DESIRED
TRACK . . . . . . . . . . . . . . . . . . . . . .39
REPEAT . . . . . . . . . . . . . . . . . . . . .40
A-B REPEAT . . . . . . . . . . . . . . . . .40
PROGRAM (Audio CD) . . . . . . . . .41
RANDOM (Audio CD) . . . . . . . . . .41
ZOOM PLAYBACK . . . . . . . . . . . .41
C
SETTINGS . . . . . . . . . . . . . . . . . . .42
CHANGING THE AUDIO
LANGUAGE OR SOUND MODE .42
CHANGING THE SUBTITLE
LANGUAGE . . . . . . . . . . . . . . . . .43
CHANGING THE CAMERA
ANGLE (Multi-Angle Pictures) . . . .43
CHANGING THE ON-SCREEN
DISPLAY . . . . . . . . . . . . . . . . . . . .44
C
CHANGING THE SETUP ITEMS .45
LANGUAGE SETTINGS . . . . . . . .45
VIDEO SETTINGS . . . . . . . . . . . . .46
AUDIO SETTINGS . . . . . . . . . . . .46
PARENTAL LOCK . . . . . . . . . . . . .47
OTHER SETTINGS . . . . . . . . . . . .48
C
LANGUAGE CODE LIST . . . . . . . .49
C
TROUBLESHOOTING GUIDE . . .50
C
MAINTENANCE . . . . . . . . . . . . . . .53
DISC HANDLING . . . . . . . . . . . . .53
C
SPECIFICATIONS . . . . . . . . . . . . .54
C
WARRANTY . . . . . . . . . . .Back Cover
- 6 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 7
FEATURES
TV/VCR
•
Hi-Fi system–
The Hi-Fi stereo recording system offers you excellent sound quality with a dynamic range of 80dB, frequency response from 20Hz to
20kHz, and 0.005% wow and flutter.
•
Rotary 4-head Record/Playback System–
Four heads ensure excellent picture quality and special effects playback.
•
Index Search–
Fast-forwards to start of next recording.
•
Slow Motion–
View recorded program at slower than normal speed.
•
Infrared remote control
•
Trilingual on screen tv/vcr setup display selectable in English or Spanish or French
•
Real time counter–
This shows the elapsed recording or playback time in hours, minutes, and seconds. The
“–” indication will appear when the tape is rewound further than the tape counter position “0:00:00”.
•
181 channel capability PLL frequency synthesizer tuner with direct station call–
(A converter may be necessary to view scrambled cable channels.)
•
Auto Clock Setting–
Allows you to set the clock function from a PBS broadcast station.
•
Closed caption system–
You may view specially labeled (cc) TV programs, movies, news, prerecorded tapes, etc. with either a dialogue caption or text display added to the program.
•
Auto power on and off system–
Automatically turns on the TV/DVD/VHS when you insert the cassette, turns off after auto-rewind, and ejects when the beginning of the tape is reached.
•
Auto rewind when the end of a tape is reached–
This function doesn’t occur when using timer recording.
•
2 Step picture search operation–
You can view a video program at a high speed or super high speed in either a forward or reverse direction in LP and
SLP mode. For SP mode only high speed.
•
Three different playback tape speeds : SP/LP/SLP
•
Two different recording tape speeds : SP/SLP
•
Auto Head Cleaner–
Automatically cleans video heads as you insert or remove a cassette.
•
Zero Return–
The tape returns to counter of
0:00:00 by rewinding or fast forwarding.
•
Still–
“Freeze” the picture at any time, for close viewing of a particular scene.
•
Digital Auto Tracking (DTR)–
Automatically adjusts the tracking for each tape you play.
•
Rental play mode–
Improves playback picture quality from worn tapes, such as rental tapes.
•
Auto repeat–
Allows you to repeat the playing of a tape indefinitely without pressing the PLAY button.
•
Time search–
Let you set the TV/DVD/VHS to advance the tape by entering the desired playback time you want to skip.
•
OTR (One Touch Recording)–
Instant timed recording from 30 to 480 minutes is possible at the push of the REC/OTR button.
•
1 Year, 8 events (including Daily and Weekly
Timer Recording)–
The built-in timer allows you to record up to 8 programs at different times on different channels up to 1 year in advance. The Daily timer allows recordings to be made of daily broadcasts, and the Weekly timer allows recording to be made once a week up to the end of the tape.
•
Auto return–
After timer recording is finished, the
TV/DVD/VHS can return to the beginning of the recording.
•
Sleep timer–
Allows you to have the TV/DVD/VHS automatically turn on or off at a desired time. (This feature is not available for DVD mode.)
Timer Program Extension–
Allow you to shift the time schedule for automatic timer recording.
•
V-CHIP–
Enables parents to prevent their children from watching inappropriate material on TV.
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.
- 7 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 8
DVD
¡
Dolby Digital sound
This player can handle Dolby Digital surround sound having 5.1 channels when connected to a Dolby Digital decoder.
¡
Still/fast/slow/step playback
Various playback modes are available including still pictures, fast forward/reverse, slow motion and step frames.
¡
Random playback for audio CD
This player can shuffle the order of tracks to play them in random order.
¡
Program playback for audio CD
You can program the order of tracks to play them in any desired order.
¡
DVD menus in a desired language
You can display DVD menus in a desired language, if available on a DVD.
¡
Screen saver/Auto power-off functions
The screen saver program starts when there is no input from the player for five minutes in the stop mode. When the screen saver program is activated for 30 minutes, the
DVD power is automatically turned off, and "DVD" appears on the screen.
¡
Subtitles in a desired language
You can select a desired language for the display subtitles, if that language is available on a disc.
¡
Selecting a camera angle
You can select the desired camera angle, if a disc contains sequences recorded from different angles.
¡
Choices for audio language and sound mode
You can select the desired audio language and sound mode, if different languages and modes are available on a disc.
¡
Parental lock
You can set the control level to limit playback of discs which may not be suitable for children.
¡
Automatic detection of discs
This player automatically detects if a loaded disc is DVD or audio CD.
¡
On-screen display
Information about the current operation can be displayed on a TV screen, allowing you to confirm the currently active functions (such as program playback), on the TV screen using the remote control.
¡
DTS (Digital Theater System)
Sound system different from Dolby Digital sound system
¡
Search
Chapter search: Search for the chapter designated by user is possible.
Title search: Search for the title designated by user is possible.
Track search: Search for the track designated by user is possible.
Time search: Search for the time designated by user is possible.
¡
Repeat
Chapter:
Title:
Repeated playback of the chapter of the disc being played is possible.
Repeated playback of the title of the disc being played is possible.
Track: Repeated playback of the track of the disc being played is possible.
Disc(audio CD): Repeated playback of the entire disc being played is possible.
A-B: The part between A and B designated by user is possible.
¡
Zoom
4-time magnified screen can be displayed.
¡
Marker
The part designated by user can be called back.
¡
Resume Play
User can resume to playback from the part at which the play was stopped.
¡
SRS TruSurround
You can enjoy stereophonic virtual space on your existing stereo system.
¡
Dimmer
Brightness of the display can be varied.
¡
Bit rate indication
¡
Dynamic range control
This unit employs TruSurround system
of SRS Labs, Inc. as virtual technology.
TruSurround and the symbol are trademarks of
SRS Labs, Inc.
TruSurround technology is incorporated under license from SRS Labs, Inc.
NOTE:
•
We do not recommend the use of universal remote controls. Not all of the functions may be controlled with a universal remote control.
If you decide to use a universal remote control with this unit, please be aware that the code number given may not operate this unit. In this case, please call the manufacturer of the universal remote control.
- 8 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 9
OPERATING CONTROLS AND FUNCTIONS
- TV/DVD/VHS FRONT PANEL - [Fig.1]
POWER VOLUME
DVD buttons
STOP OPEN/CLOSE SKIP PLAY SKIP
SEARCH
SELECT
DVD TV/VCR
TV/VCR buttons
CHANNEL REC/OTR REW PLAY F.FWD
STOP/EJECT
HEADPHONE VIDEO L
AUDIO
R
1
22
23
24
25
26
1
(DVD)
3
(TV/VCR)
14
4
13
27
28
29
30
31
32
33
2 3 4
- REMOTE CONTROL -
POWER PICTURE SLEEP SELECT
1
4
2
5
3
6
7
PAUSE
8
0
SPEED C.RESET
9
+100
+10
ZOOM
RECORD
DISPLAY
SETUP
CLEAR SEARCH MODE REPEAT
MODE
TITLE
PLAY
STOP
ENTER
3
X
VOL.
Y
AUDIO SUBTITLE ANGLE
5
[Fig. 2]
CH.
MUTE
DISC
MENU
RETURN
A-B
6
45
44
11
2
36
35
34
7 8 9 10 11 12 13 14
4
43
42
3
(DVD)
15
(TV/VCR)
5
41
40
39
38
37
1.
POWER button
Press to turn the power on and off.
2.
VOLUME
K
/
L
buttons
Press to control the volume level for the DVD and TV.
3.
SKIP buttons (for DVD)
Skip chapters or tracks to a desired point.
4.
PLAY button
Starts playback of the disc or tape contents.
5.
STOP button
Stops operation of the disc or tape.
15 16 17 18 19 20 21
6.
OPEN/CLOSE button
Press to insert discs into or remove them from the tray.
7.
Disc loading tray
8.
DVD indicator
Lights on during DVD mode.
9.
SELECT button
Press to change to TV/VCR mode or DVD mode.
NOTE: For about 4 seconds just after the DVD mode has switched to the TV mode, the button does not work to switch back to the DVD mode.
10.
TV/VCR indicator
Lights on during TV/VCR mode.
11.
CHANNEL
K
/
L
buttons
Press to select memorized channel.
12.
Recording indicator
Flashes during recording. Lights up in the Standby mode for Timer Recording.
13.
REC/OTR (RECORD) button
Press for manual recording. Activates One Touch
Recording. (OTR is only during TV/VCR mode.)
14.
REW button (for TV/VCR)
Press to rewind the tape, or to view the picture rapidly in reverse during playback mode. (Rewind
Search)
15.
FWD button (for TV/VCR)
Press to rapidly advance the tape, or to view the picture rapidly in forward during playback mode.
(Forward Search)
16.
STOP/EJECT button
Press to stop the tape motion. Press in the Stop mode to remove tape from the unit.
17.
Remote sensor window
18.
HEADPHONE jack
To connect headphone (not supplied) for personal listening.
19.
VIDEO input jack
Connect to the video output jack of a video camera or VCR.
- 9 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 10
- TV/DVD/VHS REAR PANEL - [Fig.3]
ANT.
1
AUDIO OUT
L
R
COAXIAL
46 47 48 49
20.
AUDIO L/R input jacks
Connect to the audio output jacks of a video camera or VCR.
21.
Cassette compartment
22.
PICTURE button
Press to adjust the picture.
23.
Number buttons
TV Mode:
Press two digits to directly access the desired channel.
Remember to press a "0" before a single digit channel.
+100 button–
Press to select cable channels which are equal or greater than number 100.
DVD Mode:
Press to enter the desired number.
+10 button–
Press to enter the desired numbers which are equal or greater than number 10.
24.
PAUSE button
Pauses the current disc or tape operation.
25.
SPEED button
Press to choose the desired recording speed:
SP/SLP.
26.
C.RESET button
Press to reset counter to 0:00:00.
Press to cancel a setting of timer program. (See page 33.)
27.
DISPLAY button
TV/VCR Mode:
Display the counter or the current channel number and current time on the TV screen.
DVD Mode:
Displays the current status on the TV screen for checking purposes.
28.
SETUP button
Press to enter or exit the TV menu or DVD setup mode.
29.
TITLE button
Displays the title menu.
30.
CLEAR button
Resets a setting.
31.
MODE button
Activates program playback or random playback mode.
32.
SEARCH MODE button
Press to locate a desired point.
33.
AUDIO button
Press to select a desired audio language or sound mode.
34.
SUBTITLE button
Press to select a desired subtitle language.
35.
REPEAT button
Repeats playback of the current disc, title, chapter or track.
36.
ANGLE button (DVD mode)
Press to change the camera angle to see the sequence being played back from a different angle.
SLEEP button (TV/VCR mode)
Sets the Sleep Timer. (See page 34.)
37.
A-B REPEAT button
Repeats playback of a selected section.
38.
RETURN button
Returns to the previous operation.
39.
ENTER button
Press to accept a setting.
40.
Arrow buttons
TV/VCR Mode:
Press to select a setting mode from the menu on the TV screen.
Press to select or adjust from a particular menu.
DVD Mode:
Use when making settings while watching the display on a TV screen.
41.
DISC MENU button
Displays the menus in the DVD.
42.
ZOOM Button
Enlarges part of a DVD-reproduced image.
43.
MUTE button
Mutes the sound. Press it again to resume sound.
44.
DVD button
Press to switch to DVD mode. DVD indicator on the front will lights on.
45.
TV/VCR button
- 10 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 11
Press to switch to TV/VCR mode. TV/VCR indicator on the front will lights on.
46.
ANT. in jack
Connect to an antenna, cable system, or satellite system.
47.
Power cord
Connect to a standard AC outlet (120V/60Hz).
NOTE:
Remove the power cord from the hook to avoid breaking a wire before you connect to a standard AC outlet.
48.
COAXIAL digital audio out jack
Connect to the digital input of an external amplifier or decoder.
49.
AUDIO L/R output jack
Connect to the analog audio input of an external amplifier or decoder.
Satellite Box or
Cable Box (Not supplied)
OUT
IN
PREPARATION FOR USE
ANTENNA/CABLE CONNECTION
From Cable System or
Satellite Dish
VHF/UHF Antenna
(Not supplied)
VHF Antenna (Not supplied)
From Cable
System
75-ohm
Coaxial
Cable
(Not supplied)
ANT.
75-ohm Coaxial
Cable (Not supplied) or
1
AUDIO OUT
R
COAXIAL
ANT.
or
UHF Antenna
(Not supplied)
VHF/UHF
Combiner
(Not supplied)
Flat twin-lead cable
[Fig. 4]
or
VHF/UHF SEPARATE ANTENNAS
In some areas it will be necessary to use an outdoor antenna.
CABLE WITHOUT CONVERTER/
DESCRAMBLER BOX
Use this connection if your cable system connects directly to your TV/DVD/VHS without a converter box.
By using this connection you can:
1) Use the TV/DVD/VHS remote to select channels.
2) Program one or more unscrambled channels for
Automatic Timer Recording.
NOTE: This unit will ONLY record and view the same channel.
- 11 -
CABLE WITH CONVERTER/
DESCRAMBLER BOX OR SATELLITE
BOX
If your cable service supplies you with a converter box or if you use a satellite system, you can use the basic connection shown in the illustration.
By using this connection you can also record scrambled channels. However, channel selection must be made with the converter box or satellite box. This means that channels cannot be changed using the
TV/DVD/VHS Remote Control. Unattended timer recording is limited to one channel at a time.
Antenna/Cable Connections
Continued on the Next Page.
EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 12
TO RECORD A SCRAMBLED/UNSCRAM-
BLED CHANNEL
1. Set the TV/DVD/VHS channel selector to the output channel of the Cable Converter Box or Satellite
Box. (Ex. CH3)
2.Select the channel to record from your Cable
Converter Box or Satellite Box.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the
NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.
CONNECTING TO EXTERNAL
INPUT JACKS
When you watch a program recorded on an another source (VCR or video camera), use the audio/video input jacks on the front of the TV/DVD/VHS.
Connect the audio/video output jacks of another source to the AUDIO L/R and VIDEO jacks of this
TV/DVD/VHS.
Then press the SELECT button until "VIDEO" appears on the screen.
NOTE:
•
When you connect a monaural VCR (another source) to this TV/DVD/VHS, connect the Audio output jack of the monaural VCR (another source) to the AUDIO L jack of this TV/DVD/VHS. The audio will output in both L and R channel equally.
[Another source]
To the audio output jacks
INSTALLING THE BATTERIES
1)Open the battery compartment cover by pressing the cover on the remote unit in the direction of the arrow.
2)Insert 2 “AA” penlight batteries into the battery compartment in the direction indicated by the polarity (+/-) markings.
3)Replace the cover.
EXTERNAL INPUT MODE
When using an external input signal (another VCR or video camera), connect the player’s audio/video output cables to the AUDIO L/R IN/
VIDEO IN jacks of your
TV/DVD/VHS. Then press the
CHANNEL K or L button until
“AUX” appears on the screen.
AUX
etc.
To the video output jack
Audio/Video coaxial cable
(not supplied)
HEADPHONE VIDEO L-AUDIO-R
[Front of the
TV/DVD/VHS]
[Fig. 5]
- 12 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 13
CONNECTING TO A DOLBY DIGITAL DECODER,
DTS DECODER, OR MPEG DECODER (for DVD)
If using this TV/DVD/VHS to play back a TV/DVD/VHS in a 5.1 channel Dolby Digital surround, DTS surround, or MPEG surround format, the TV/DVD/VHS outputs a Dolby Digital, DTS, or MPEG data stream from its COAXIAL DIGITAL AUDIO OUT jack. By hooking the player up to a Dolby Digital or DTS decoder, you can enjoy a more convincing, realistic ambience with powerful and high-quality surround sound of a professional standard such as can be heard in movie theaters.
Use audio coaxial digital cables (commercially available) for the audio connections.
Front speaker
(left)
Center speaker
Front speaker
(right)
ANT.
Surround speaker
(left)
Dolby Digital or DTS decoder
Surround speaker
(right)
To COAXIAL DIGITAL
AUDIO INPUT jack
Subwoofer
1
L
AUDIO OUT
R
COAXIAL
To DIGITAL AUDIO OUT
(PCM/BITSTREAM)
COAXIAL jack
[Fig. 8]
NOTES:
•
Be sure to turn off the power to all components in the system before connecting another component.
•
Refer to the Owner's Manuals for the components to be connected to the TV/DVD/VHS.
•
If output Dolby Digital audio, connect to a Dolby Digital decoder, and set Dolby Digital to on for audio output in the setup mode.
•
If output DTS audio, connect to a DTS decoder, and set DTS to ON for audio output in the setup mode.
•
If played a disc indicated MPEG audio, connect to a MPEG decoder, and set MPEG to ON for audio output in the setup mode.
•
Unless connected to a Dolby Digital decoder, a DTS decoder, or a MPEG decoder, set Dolby Digital, DTS, or MPEG to off for audio output in the setup mode. Playing a TV/DVD/VHS using incorrect settings may generate noise distortion, and may also damage the speakers.
•
When DOLBY DIGITAL is set to OFF and VIRTUAL 3D to ON for audio output in the setup mode and you select the audio source in a 5.1 channel Dolby Digital surround format, the audio will be muted.
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby
Laboratories.
“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems Inc.
- 13 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 14
CONNECTING TO A STEREO SYSTEM (for DVD)
Stereo system
ANT.
1
L
AUDIO OUT
R
COAXIAL
To ANALOG AUDIO INPUT jacks
To Right (red) and Left (white)
AUDIO OUT jacks
(only DVD AUDIO OUT)
[Fig. 6]
NOTES:
•
Be sure to turn off the power to all components in the system before connecting another component.
•
Refer to the Owner's Manuals for your, stereo system and any other components to be connected to the
TV/DVD/VHS.
CONNECTING TO AN AMPLIFIER EQUIPPED WITH DIGITAL
INPUT JACKS SUCH AS MD DECK OR DAT DECK (for DVD)
Use an audio coaxial digital cable (commercially available) for the audio connections.
Connecting to an amplifier equipped with digital input jacks such as MD Deck or Dat Deck.
Amplifier equipped with digital input jacks, MD deck,
DAT deck, etc.
ANT.
To COAXIAL DIGITAL
AUDIO INPUT jack
1
L
AUDIO OUT
R
COAXIAL
To DIGITAL AUDIO OUT
(PCM/BITSTREAM)
COAXIAL jack
(only DVD AUDIO OUT)
[Fig. 7]
NOTES:
•
The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital sound by an MD or DAT deck.
•
Be sure to turn off the power to all components in the system before connecting another component.
•
Refer to the Owner's Manuals for the components to be connected to the TV/DVD/VHS.
•
Set DOLBY DIGITAL and DTS to OFF for audio output in the setup mode. Playing a TV/DVD/VHS using incorrect settings may generate noise distortion, and may also damage the speakers.
•
When DOLBY DIGITAL is set to OFF and VIRTUAL 3D to ON for audio output in the setup mode and you select the audio source in a 5.1 channel Dolby Digital surround format, the audio will be muted.
- 14 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 15
TV/VCR SECTION
SET UP FOR USE
You can program the tuner to scan all the channels you receive in your area.
NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just select the TV/DVD/VHS channel selector to the output channel of the cable box or satellite box (Ex CH3).
Then select the channel to be viewed on the Cable Box or Satellite Box.
CHANNEL SET UP FOR THE
FIRST TIME
1
Plug in the TV/DVD/VHS power cord
Plug the TV/DVD/VHS power cord into a standard AC outlet.
NOTE:
•
If some digits appear in the corner of the screen, press the POWER button without unplugging the power cord.
DELETING (OR ADDING)
CHANNEL
The channels you no longer receive or seldom watch can be deleted from the memory. (Of course, you can add the deleted channel into the memory again.)
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
B
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Turn on the TV/DVD/VHS
Press the POWER button to turn on the TV/DVD/VHS.
1
Select “CHANNEL SET UP”
Press the SETUP button on the remote control.
Press the Arrow K or L button to point to “CHANNEL SET UP”.
Then, press the Arrow B button.
2
Select “ADD/DELETE CH”
Press the Arrow K or L button to point to “ADD/DELETE CH”.
Press the Arrow B button.
– CHANNEL SET UP –
B ADD / DELETE CH (TV)
AUTO PRESET
3
Select “ENGLISH” or “ESPAÑOL” or
“FRANÇAIS”
Select “ENGLISH” or
“ESPAÑOL”=Spanish or
“FRANÇAIS” =French using the
Arrow B or s button. “[ ]” indicate the selected language.
– SET UP –
B
LANGUAGE
[ENGLISH] ESP
AUTO PRESET
FRA
4
Begin auto preset
Press the Arrow K or L button to point to “AUTO PRESET”.
Then press the Arrow B button.
The tuner scans and memorizes all active channels in your area.
– SET UP –
LANGUAGE
[ENGLISH] ESP
B AUTO PRESET
FRA
NOTES:
•
The TV/DVD/VHS distinguishes between standard
TV channels and cable channels.
•
If you want to play or record a video tape
BEFORE presetting the tuner, you must press the
SETUP button on the remote control. To preset the tuner again, see “CHANNEL SET UP AGAIN” on page 15.
•
The TV/DVD/VHS may memorize TV channels as
CATV channels if reception conditions is poor. If this happens, try AUTO MEMO action again when reception conditions are better.
5
After scanning
The tuner stops on the lowest memorized channel.
If you want to recall the selected channels, you can select the desired channel directly with the remote control number buttons or CHANNEL K or L.
3
Enter the desired channel number
Press the Arrow K or L button until your desired channel number appears. (You can also use the number buttons or the CHANNEL K/L button to enter it) (Example: CH8)
ADD / DELETE
08
4
Delete (or add) it from (into) memory
Press the Arrow B or s button. The channel number changes to light red. The channel is deleted from memory.
•
To delete another channel, repeat steps [3] and [4].
•
If you press the Arrow B or s button again, the channel is memorized again.
5
Exit the channel setup mode
Added channel: Light blue.
Deleted channel: Light red.
Press the SETUP button on the remote control to returns to TV mode.
NOTE: To confirm that channel(s) has been deleted or added, press the CHANNEL K or L button.
- 15 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 16
CHANNEL SET UP AGAIN
Make sure ...
•
Press the POWER button to turn on the
TV/DVD/VHS.
1
Select “CHANNEL SET UP”
Press the SETUP button on the remote control.
Press the Arrow K or L button to point to “CHANNEL SET UP”.
Then, press the Arrow B button.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
B
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Begin auto preset
Press the Arrow K or L button to point to “AUTO PRESET”.
Then, press the Arrow B button.
The tuner scans and memorizes all the active channels in your area.
– CHANNEL SET UP –
ADD / DELETE CH (TV)
B
AUTO PRESET
3
After scanning
The tuner stops on the lowest memorized channel.
SELECTING THE LANGUAGE
Make sure ...
•
Press the POWER button to turn on the
TV/DVD/VHS.
NOTE: This function effects only the language on the screen menu and not the audio source.
1
Select “LANGUAGE”
Press the SETUP button on the remote control.
Press the Arrow K or L button to point to “LANGUAGE”.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
B
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Select “ENGLISH” or “ESPAÑOL” or
“FRANÇAIS”
Select “ENGLISH” or “ESPAÑOL”= Spanish or
“FRANÇAIS”= French using the Arrow B or s button.
3
Exit the Language mode
Press the SETUP button on the remote control to return to TV mode.
NOTE: If Spanish or French is selected accidentally, press the SETUP button on the remote control, press the Arrow K button to point to “IDIOMA
[ESPAÑOL]” or “LANGAGE” [FRANÇAIS], then press the Arrow B button, then press the SETUP button on the remote control.
DAYLIGHT-SAVING TIME
Select this feature and the TV/DVD/VHS’s clock automatically will advance one hour in April, then reverse one hour in October.
When Daylight-Saving Time is ON, the clock will change automatically as follows:
•
First Sunday of April :
At 2 AM the clock immediately changes to 3 AM. Any timer programming you have set to occur between 2 AM and 3 AM will not record.
•
Last Sunday of October :
At 2 AM the clock immediately changes to 1 AM.
Make sure ...
•
Press the POWER button to turn on the
TV/DVD/VHS.
1
Select “SETTING CLOCK”
Press the SETUP button on the remote control.
Press the Arrow K or L button to point to “SETTING CLOCK”.
Then, press the Arrow B button.
B
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Set “D.S.T.” (Daylight-Saving Time) to [ON]
Press the Arrow K or L button to point to “D.S.T.”.
Then, press the Arrow B or s button until [ON] appears.
– SETTING CLOCK –
AUTO CLOCK
AUTO CLOCK CH
MANUAL CLOCK SET
[ON]
[AUTO]
B D.S.T.
[ON]
3
Exit the Daylight-Saving Time mode
Press the SETUP button on the remote control to return to TV mode.
TO CANCEL THE DAYLIGHT-SAVING
TIME
Repeat steps [1] to [2], select [OFF] using the Arrow
B or s button.
- 16 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 17
CLOCK SET UP
(AUTO / MANUAL)
Set the clock accurately for proper automatic timer recording. If the Public Broadcasting Station (PBS) is available in your area, follow “AUTO CLOCK SET-
TING”. If it is not, follow “MANUAL CLOCK SET-
TING”.
2
Set “AUTO CLOCK” to [ON]
Press the Arrow B or s button repeatedly until [ON] appears.
– SETTING CLOCK –
B
AUTO CLOCK
AUTO CLOCK CH
[ON]
[AUTO]
MANUAL CLOCK SET
D.S.T.
[OFF]
AUTO CLOCK SETTING
You can have the TV/DVD/VHS set the clock automatically by using the Public Broadcasting Station
(PBS) channel in your area. Once you have set the clock by using the following procedure, the
TV/DVD/VHS will automatically monitor the correct time and date being broadcast by the PBS station in your area, using a new service called Extended Data
Service (XDS).
Make sure ...
•
TV/DVD/VHS power must be turned on.
•
Confirm that the antenna connections are correct.
•
The cable converter box must be turned on if your
TV/DVD/VHS is connected directly to it. (See
NOTES:)
•
The channel is properly set in advance. (See page
16.)
3
Enter the channel number for the PBS station
Press the Arrow K or L button to point to “AUTO CLOCK CH”.
Then press the Arrow B or s button until the channel number for your local PBS station appears.
– SETTING CLOCK –
AUTO CLOCK
AUTO CLOCK CH
MANUAL CLOCK SET
B D.S.T.
[ON]
[AUTO]
[OFF]
If you do not know the PBS channel number, leave it set to [AUTO] which is located before [2]. The
TV/DVD/VHS will search automatically all available channels for the local PBS station, and will select that channel.
4
Exit the Auto Clock Setting
Press the SETUP button on the remote control to return to TV mode.
5
Turn off the TV/DVD/VHS
Turn the TV/DVD/VHS off. Because the Auto Clock functions automatically while the TV/DVD/VHS is off.
NOTES:
•
Auto clock setting only needs to be set once. But it can be done again if the clock’s time has become incorrect for some reason.
•
If the TV/DVD/VHS is connected directly to a cable converter box or satellite box, the local PBS station must be selected on the cable box itself, and the TV/DVD/VHS must be set to the output channel of the cable converter box or satellite box (usually channel 3 or 4), to be able to set up or correct the clock automatically.
If you do not know what your local PBS station is, then follow “Manual Clock Settings” on page 18.
The TV/DVD/VHS cannot control the channels of the cable converter box or satellite box.
If you choose [AUTO],
• the TV/DVD/VHS must search until the PBS channel is found. It must scan each channel for a couple of seconds to determine if that channel is transmitting the XDS signal.
• if the time, that is automatically set by this selected
PBS station is incorrect, it may not be your local
PBS station, but one from a different time zone. Or there is a case that no channel is broadcasting the
XDS signal in your area, as shown by no time. In these cases, you must manually enter the correct local PBS station, or set the clock manually and turn off the Auto Clock Setting feature.
1
Select “SETTING CLOCK”
Press the SETUP button on the remote control.
Press the Arrow K or L button to point to “SETTING CLOCK”.
Then, press the Arrow B button.
- TV/VCR SETUP -
TIMER PROGRAMMING
B
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
- 17 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 18
MANUAL CLOCK SETTING
Make sure ...
•
TV/DVD/VHS power must be turned on.
In the example below, the clock is to be set to:
DATE May 7th, 2002
SETTING TIME 5:40PM
1
Select “SETTING CLOCK”
Press the SETUP button on the remote control.
Press the Arrow K or L button to point to “SETTING CLOCK”.
Then, press the Arrow B button.
- TV/VCR SETUP -
TIMER PROGRAMMING
B
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Select “MANUAL CLOCK
– SETTING CLOCK –
SET”
AUTO CLOCK
AUTO CLOCK CH
Press the Arrow K or L button to point to “MANUAL CLOCK SET”.
Then, press the Arrow B button.
B
MANUAL CLOCK SET
D.S.T.
[ON]
[AUTO]
[OFF]
3
Select the month
Press the Arrow K or L button until your desired month appears.
(Example: May
→ 05)
Then, press the Arrow B button.
4
Select the day
Press the Arrow K or L button until your desired day appears.
(Example: 7th
→ 07)
Then, press the Arrow B button.
5
Select the year
Press the Arrow K or L button until your desired year appears.
(Example: 2002)
Then, press the Arrow B button.
– MANUAL CLOCK SET –
MONTH DAY YEAR
0 5 / – – – – – – – – –
HOUR MINUTE
– – : – – – –
– MANUAL CLOCK SET –
MONTH DAY YEAR
0 5 / 0 7 – – – – – – –
HOUR MINUTE
– – : – – – –
– MANUAL CLOCK SET –
MONTH DAY YEAR
0 5 / 0 7 TUE 2 0 0 2
HOUR MINUTE
– – : – – – –
6
Select the hour
Press the Arrow K or L button until your desired hour appears.
(Example: 5, PM)
Then, press the Arrow B button.
7
Select the minute
Press the Arrow K or L button until the desired minute appears.
(Example: 40)
– MANUAL CLOCK SET –
MONTH DAY YEAR
0 5 / 0 7 TUE 2 0 0 2
HOUR MINUTE
0 5 : – – PM
– MANUAL CLOCK SET –
MONTH DAY YEAR
0 5 / 0 7 TUE 2 0 0 2
HOUR MINUTE
0 5 : 4 0 PM
8
Start the clock
Press the SETUP button on the remote control.
5:40 PM
Although seconds are not displayed, they begin counting from 00 when you press the SETUP button on the remote control. Use this feature to synchronize the clock with the correct time.
NOTE:
When unplugging the AC cord or if there is a power failure for more than 30 seconds, you may have to reset the clock.
TO CHANGE CLOCK SETTING
If you want to change the clock,
1)Follow steps [1] and [2].
2)Select where you want to change using the Arrow
B or s button.
3)Enter correct numbers using the Arrow K or L button.
4)Press the SETUP button on the remote control to start the clock.
PLEASE NOTE:
If there is no local PBS station in your area or on your cable system, select “AUTO CLOCK” and press the Arrow B or s button to turn [OFF] this function. Then you can manually adjust the clock.
- 18 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 19
TV OPERATION
WATCHING A TV PROGRAM
1
Turn on the TV/DVD/VHS
Press the POWER button to turn on the
TV/DVD/VHS.
2
Select the channel number
Press the CHANNEL K or L button to select your desired channel number or press the number buttons on the remote control.
Remember: If the TV/DVD/VHS is connected to a cable box or satellite box, the TV/DVD/VHS must be on CH3 or CH4, then the channel to be viewed must be selected on the cable box or satellite box.
PICTURE CONTROL
The TV/DVD/VHS’s picture controls – BRIGHT,
CONTRAST, COLOR, TINT and SHARPNESS – are preset to factory specifications. Although they are usually the best, you may need to make some further adjustments for a natural looking image.
NOTES:
•
Procedures must be followed within 5 seconds or the Picture Control mode will be cancelled.
•
When setting the Picture Control, the Game mode will be cancelled.
Make sure ...
•
TV/DVD/VHS power must be turned on.
3
Adjust sound
Press the VOLUME X
Y button to adjust the volume.
DEGAUSSING
Magnetism from nearby appliances might affect the color of the TV picture.
If this happens, move this unit away from the appliance. If the color is still not correct, disconnect power cord from AC outlet then reconnect it after 30 minutes.
1
Select “PICTURE CONTROL”
Press the PICTURE button on the remote control.
VOLUME 20
C C C C C
C C C C C C C
NOTES:
•
If you press the CHANNEL o or p in the DVD mode, you can change the TV channels.
Even if you turn off the TV/DVD/VHS in the DVD mode, when you turn it on again, it will go into the
TV/VCR mode.
2
Select item you want to adjust
Press the Arrow K or L button until desired control is displayed.
BRIGHT
CONTRAST
COLOR
TINT
SHARPNESS
BRIGHT
P P
+
3
Adjust the picture control
Press the Arrow B or s button to adjust to your desired level.
Arrow s
BRIGHT
to decrease brightness
CONTRAST
to decrease contrast
COLOR
to pale
TINT
to purple
SHARPNESS
to soft
Arrow B to increase brightness to increase contrast to brilliant to green to clear
•
If there is a power failure of any kind, the unit will retain its memory for this feature.
- 19 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 20
CLOSED CAPTION SYSTEM
You can view specially labeled (cc) TV programs, movies, news, pre-recorded tapes with either a dialogue caption or text display.
CAPTION mode:
By choosing the caption mode, you can watch dramas, movies and news while captioning the dialogues and the contents of news.
TEXT mode:
By choosing the text mode, you can watch half screen text information if you want.
1-2:
You may get these captions or text information by selecting either “1” or “2”. Caption “2” is used, usually for a second language if available.
1
Select “CAPTION”
Press the SETUP button on the remote control.
Press the Arrow K or L button to point to “CAPTION”.
B
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Select your desired caption menu
Press the Arrow B or s button until your desired caption menu appears.
([CAPTION1], [CAPTION2],
[TEXT1] or [TEXT2])
B
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [CAPTION1]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
NOTE:
Not all programs are broadcast with closed captions.
Your television is designed to provide error free closed captions from high quality antenna, cable and
VCR signals. Conversely, poor quality signals are likely to result in caption errors or no captions at all.
Common signal conditions which may cause captions errors are listed below:
•
Automobile ignition noise
•
Electric motor brush noise
•
Weak snowy reception on TV screen
•
Multiplex signal reception displaying picture ghosts or airplane flutter.
•
Playback of poorly recorded or worn VCR tapes.
NOTE:
If the TV/DVD/VHS displays a black box on the TV screen, this means that the TV/DVD/VHS is set to the TEXT mode. To clear screen, select [CAPTION1], [CAPTION2] or [OFF].
Make sure ...
•
TV/DVD/VHS power must be turned on.
3
Exit the caption setting mode
Press the SETUP button on the remote control to return to TV mode.
TO CANCEL THE CLOSED CAPTION
SYSTEM
Repeat steps [1] and [2], select [OFF] using the
Arrow B or s button. Press the SETUP button on the remote control to return to TV mode.
WHEN THE CLOSED CAPTION MODE
IS ON
The On-Screen Display will disappear after 5 seconds.
•
This is also true when the MUTE button is pressed, and when the PAUSE button is pressed while recording.
•
If there is a power failure of any kind, the unit will retain its memory for this feature.
- 20 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 21
V-CHIP SET UP
V-CHIP enables parents to prevent their children from watching inappropriate material on TV.
V-CHIP reads the ratings for programming (except for news and sports programs, unedited movies on premium cable channels, and Emergency Broadcast
System signals), then denies access to programming if the program’s rating meets the limitations you select. In this case, “PROTECTED PROGRAM by
...” message appears on the TV screen. You can watch the protected program by entering access code
(default 0000).
To block ratings, follow the steps below.
•
Programming may be rated by the Motion Picture
Association of America (MPAA) or according to the Television Parental Guidelines. In order to block any inappropriate programming, set your limits in both places (MPAA RATING and TV
RATING).
TV RATING SET UP
Make sure ...
•
TV/DVD/VHS power must be turned on.
1
Select “V-CHIP SET UP”
Press the SETUP button on the remote control.
Press the Arrow K or L button to point to “V-CHIP SET UP”.
Then, press the Arrow B button.
B
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Input Access code
Use the number buttons to enter 4digit access code. The default code is 0000.
ACCESS CODE
_ _ _ _
3
Select “TV RATING”
Press the Arrow K or L button to point to “TV RATING”.
Then, press the Arrow B button.
– V-CHIP SET UP –
B
TV RATING
MPAA RATING
CHANGE CODE
4
Select your desired item
Press the Arrow K or L button to point to your desired item.
Then, press the Arrow B button to select [BLOCK] or [VIEW].
B TV–Y
TV–Y7 (
TV–G
TV–PG (
TV–14 (
TV–MA (
)
)
)
)
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
•
When you select the rating category and turn it
[BLOCK], the higher rating will turn [BLOCK] automatically. Also, the lower rating will turn
[VIEW] automatically.
•
When you turn “TV-Y” to [VIEW], the all ratings will turn to [VIEW] automatically.
Selection
TV-Y
Rating Category Explanations
Appropriate for all children
TV-Y7 Appropriate for children seven and older
TV-G General Audience
TV-PG Parental Guidance suggested.
TV-14 Unsuitable for children under 14
TV-MA Mature audience only
When you select TV-Y7, TV-PG, TV-14, or TV-MA and you press the Arrow B button, the sub-ratings will appear on the TV screen.
If you select the rating category (example: TV-PG) and turn it [BLOCK] or [VIEW], the sub-ratings
(example: V for Violence) will turn [BLOCK] or
[VIEW] automatically.
You can set the sub-ratings to [BLOCK] or [VIEW] individually when the rating category is set to
[BLOCK].
To set the sub-ratings individually, follow the steps below.
•
When you select [TV-Y7]:
Press the Arrow L or K button to select “FV” (Fantasy Violence).
Then, press the Arrow B button
B
TV–Y7
FV
[BLOCK]
[BLOCK] to select [BLOCK] or [VIEW].
•
When you select [TV-PG], [TV-14] or [TV-MA]:
Press the Arrow L or K button to select “D”(Suggestive Dialog),
“L”(Coarse Language),
“S”(Sexual Situation), or
“V”(Violence). Then, press the
Arrow B button to select
[BLOCK] or [VIEW].
TV–PG
B
D
L
S
V
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
Note: When you select [TV-MA], “D” does not appear on the TV screen.
•
The sub-ratings which set to
[BLOCK] appears next to the rating category in the TV RATING
B
TV–Y
TV–Y7 ( )
TV–G
TV–PG (DLSV )
TV–14 (DLSV )
TV–MA ( LSV )
[VIEW]
[VIEW]
[VIEW]
[BLOCK]
[BLOCK]
[BLOCK] menu.
5
Exit the V-Chip setting mode
Press the SETUP button on the remote control to return to original mode.
- 21 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 22
MPAA RATING SET UP
Make sure ...
•
TV/DVD/VHS power must be turned on.
1
Select “V-CHIP SET UP”
Press the SETUP button on the remote control.
Press the Arrow K or L button to point to “V-CHIP SET UP”.
Then, press the Arrow B button.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
B
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
CHANGE ACCESS CODE
To change access code, follow the steps.
1
Press the SETUP button so that the TV/VCR SETUP display appears on the TV screen.
2
Press the Arrow K or L button to point to "V-CHIP SET UP". Then, press the Arrow B button.
B
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Use the number buttons to enter 4digit access code. The default code is 0000.
ACCESS CODE
_ _ _ _
3
Use the number buttons to enter 4digit access code. The default code is 0000.
ACCESS CODE
_ _ _ _
3
Select “MPAA RATING”
Press the Arrow K or L button to point to “MPAA RATING”.
Then, press the Arrow B button.
– V-CHIP SET UP –
TV RATING
B
MPAA RATING
CHANGE CODE
4
Press the Arrow K or L button to point to "CHANGE CODE". Then, press the Arrow B button.
– V-CHIP SET UP –
TV RATING
MPAA RATING
B
CHANGE CODE
Selection
G
PG
Rating Category Explanations
General Audience
Parental Guidance suggested.
PG-13 Unsuitable for children under 13
R Restricted; under 17 requires accompanying parent or adult guardian
NC-17 No one under 17 admitted
X Mature audience only
4
Select your desired item
Press the Arrow K or L button to point to your desired item.
Then, press the Arrow B button to
G
PG
PG–13
B
R
NC–17
X select [BLOCK] or [VIEW].
•
When you select the rating category and turn it [BLOCK], the higher rating will
[VIEW]
[VIEW]
[VIEW]
[BLOCK]
[BLOCK]
[BLOCK] turn [BLOCK] automatically. Also, the lower rating will turn [VIEW] automatically.
•
When you turn “G” to [VIEW], the all ratings will turn to [VIEW] automatically.
5
Exit the V-Chip setting mode
Press the SETUP button on the remote control to return to original mode.
5
Use the number buttons to enter your desired access code in the
NEW CODE space. Then enter the same code in the CONFIRM
CODE space. V-CHIP SET UP screen appear on the screen.
•
If you enter wrong code, repeat step 5, making sure you enter the same new code exactly in the confirm code space.
NEW CODE
_ _ _ _
CONFIRM CODE
_ _ _ _
NEW CODE
X X X X
CONFIRM CODE
_ _ _ _
6
Press the SETUP button to exit the TV/VCR SETUP.
Note:
•
If you unplug the power code or power failure occurs, the changed access code will be lost and will return to default (0000). Change your access code again as necessary.
- 22 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 23
MTS(Multi-Channel Television sound)SYSTEM
You can record or listen to a program in MTS stereo.
When you play a VHS tape, or receive a broadcast on the
TV/DVD/VHS tuner channel you are watching, the status shown below will appear when you press the DISPLAY button on the remote control.
4]
CHECKING THE SELECTED MTS MODE
PLAY B
HIFI
12:00AM
CH 123
STEREO/SAP
SP COUNT 0:00:00
3]
2]
1]
SAP
Second Audio Program, which means your program, can also be received in a second language or sometimes a radio station.
HIFI
High Fidelity which produces better sound than standard stereo TV/DVD/VHSs.
1] When a program is broadcast in stereo, STEREO appears on the TV screen.
2] When a program is broadcast in second audio,
SAP appears on the TV screen.
3] When a program broadcast both in stereo and second audio, STEREO and SAP appear on the TV screen.
NOTE: Although a program may be broadcast in both stereo and second audio, you cannot record in both stereo and second audio at the same time.
4] While the TV/DVD/VHS is set in HIFI stereo mode and playback mode. HIFI appears on the
TV screen. While the TV/DVD/VHS is set in monaural(MONO) mode, HIFI disappears from the TV screen.
NOTE: If you play non-HIFI tapes while the
TV/DVD/VHS is set in HIFI, HIFI will disappear from the TV screen and the
TV/DVD/VHS will play automatically in monaural.
MTS RECORDING/MONITOR MODE
Type of broadcast Display on STEREO/SAP the TV screen SELECTION
Regular
(monaural audio)
-None-Invalid-
Stereo broadcast
Bilingual broadcast
STEREO
SAP
-Invalid-
STEREO*
Stereo & Bilingual broadcast
STEREO
SAP
SAP*
STEREO*
SAP*
Hi-Fi audio track(2-channel) Normal audio
L-channel R-channel track
Mono Mono Mono
L
Main audio program
Sub audio program
L sub audio program
R
Main audio program
Sub audio program
R sub audio program
L+R
Main audio program
Sub audio program
L+R sub audio program
*
You must select the recording mode in TV AUDIO [STEREO] or [SAP] when you record a broadcast.
- 23 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 24
SELECTING THE MTS SYSTEM
Make sure ...
•
TV/DVD/VHS power must be turned on.
TO SELECT HIFI MODE
1
Select “USER’S SET UP”
Press the SETUP button on the remote control.
Press the Arrow K or L button to point to “USER’S SET UP”. Then, press the Arrow Bbutton.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Select“VCR AUDIO”
– USER’S SET UP –
Press the Arrow K or L button to point to“VCR AUDIO”. Then, press the Arrow Bbutton.
RENTAL
REPEAT PLAY
AUTO RETURN
B
VCR AUDIO
TV AUDIO
[OFF]
[OFF]
[OFF]
[HIFI]
[STEREO]
3
Select [HIFI]
Press the Arrow B or s button until [HIFI] appears.
– USER’S SET UP –
RENTAL
REPEAT PLAY
AUTO RETURN
B
VCR AUDIO
TV AUDIO
[OFF]
[OFF]
[OFF]
[HIFI]
[STEREO]
TO SELECT MONO MODE
You can change the selection to “MONO” if you want to listen to HIFI tapes in normal audio playback.
1) Press the SETUP button on the remote control.
Press the Arrow K or L button to point to
“USER’S SET UP”.Then, press the Arrow B button.
2) Press the Arrow K or L button to point to
“VCR AUDIO”. Then, press Arrow Bbutton.
3) Press the Arrow B or s button until [MONO] appears.
4) Press the SETUP button on the remote control to return to TV mode.
TO SELECT STEREO, SAP, OR MONO
1
Select “USER’S SET UP”
Press the “SETUP” button on the remote control.
Press the Arrow K or L button to point to “USER’S SET UP”.Then, press the Arrow B button.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
4
To return to TV mode
Press the SETUP button on the remote control to return to TV mode.
NOTES:
•
Normally, “HIFI” should be selected for playback with HIFI sound.
•
When you play non-HIFI tapes, the TV/DVD/VHS will play automatically in the monaural mode.
•
The TV/DVD/VHS records automatically MTS broadcasts in HIFI stereo sound unless you select
SAP mode recording before you begin recording.
2
Select “TV AUDIO”
Press the Arrow K or L button to point to“TV AUDIO”. Then, press the Arrow Bbutton.
– USER’S SET UP –
RENTAL
REPEAT PLAY
AUTO RETURN
VCR AUDIO
B
TV AUDIO
[OFF]
[OFF]
[OFF]
[HIFI]
[STEREO]
3
Select [STEREO], [SAP], or [MONO]
Press the Arrow B or s button until [STEREO],
[SAP], or [MONO] appears.
4
To return to TV mode
Press the SETUP button on the remote control to return to TV mode.
NOTES:
• You must select the recording mode,either TV
AUDIO [STEREO] or [SAP] when you record a broadcast.
Refer to “MTS RECORDING/MONITOR MODE”.
• If you select second audio when second audio is not available, the TV/DVD/VHS will record normal audio.
- 24 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 25
VIDEO CASSETTE
This TV/DVD/VHS will operate with any cassette that has the mark. For best results, we recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.
PRECAUTIONS
•
Avoid moisture. Moisture condensation may occur on the tape if it is moved from a cold place to a warm place or visa versa. Before using a tape with these conditions, to avoid damage of the tape and your TV/DVD/VHS, wait until the tape has warmed to room temperature and the moisture has evaporated.
•
Avoid extreme heat, high humidity and magnetic fields.
•
Do not tamper with the cassette mechanism.
•
Do not touch the tape with your fingers.
INSERTING A CASSETTE
Insert the cassette in the direction as shown. Push in gently, but continuously, on the center-back of the cassette until it is drawn into the TV/DVD/VHS. The
TV/DVD/VHS will automatically turn on.
Window
CORRECT
WRONG
TWO DIFFERENT TAPE SPEEDS
Before recording, select the tape speed from : SP
mode (Standard Play) or SLP mode (Super Long
Play).
The table below shows the maximum recording/playback time using T60, T120 or T160 tapes in each mode.
Tape Speed Recording/Playback Time
Type of tape
T60
SP mode 1 hour
SLP mode
T120
2 hours
T160
2-2/3 hours
3 hours 6 hours 8 hours
Note: You can play back a tape recorded in LP mode
(Long Play).
REMOVING A CASSETTE
1)In the Stop mode, press the EJECT button on the remote control or press the STOP/EJECT button on the TV/DVD/VHS. The cassette will eject.
2)Pull the cassette out of the cassette compartment.
3)Store the cassette in its case as shown.
ERASE PREVENTION
You can prevent accidental erasing of recording by breaking off the tab on the back edge of the cassette.
Tab
If you decide to record on the tape again, cover the hole with plastic tape.
Transparent Tape
- 25 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 26
PLAYBACK
NORMAL PLAYBACK
Make sure ...
•
TV/DVD/VHS power must be turned on.
1
Insert a prerecorded tape
If the erase-protection tab has been removed, the
TV/DVD/VHS will start playback automatically.
2
To begin playback
Press the PLAY button.
PLAY B
3
To stop playback
Press the STOP button when playback is completed.
STOP
SLOW MOTION
During pause, press the FWD button to reduce the playback speed. The TV/DVD/VHS mutes the sound during slow motion. Press the PLAY button to return to normal playback.
NOTE: If it is left in the Slow mode for more than five minutes, the TV/DVD/VHS will automatically go into the Stop mode.
PICTURE SEARCH
This feature is very useful in finding or skipping over a particular scene on a tape. In this mode, the sound will be muted.
1)You may view a video tape at a high speed in either a forward or reverse direction by pressing the F.FWD or REW button. (in the SP / LP / SLP modes)
NOTE:
•
If you press the F.FWD or REW button in the
DVD mode, the VCR forward or reverse will start.
Please press the STOP button to stop it.
2)Press it again and the TV/DVD/VHS will now search in super high speed. (in the LP / SLP modes only)
NOTE: Tapes recorded in the SP or LP mode will display a noise bar on the TV screen and the picture may revert to Black and White. This is normal.
3)Press the PLAY button to return to normal speed.
NOTES:
•
If you press the TV/VCR side PLAY button in the
DVD mode, you can start the VCR playback.
•
If you press the SELECT button in the VCR playback, it will stop and the mode will change to the DVD mode. In addition, the same function operates with the DVD side
PLAY button or OPEN/CLOSE button.
TRACKING ADJUSTMENT
•
Tracking adjustment will be set automatically
(Digital Tracking function) when you start playback.
•
However when playing pre-recorded tapes or tapes recorded on units other than your own, noise lines
(black and white streaks) may appear on the playback picture. If this occurs, you can adjust the tracking control manually by pressing the CHAN-
NEL K or L button until the streaks disappear. To return to the DTR function, stop the tape once and start playback again.
•
You can reduce the noise lines by pressing the
CHANNEL K or L button in slow mode, too.
Tracking adjustment in Slow mode will not be set automatically.
STILL PICTURE
You can view a still picture on the TV screen during playback (the Still mode). Press the PAUSE button during playback. Only tapes recorded in the SLP mode will show the least amount of lines.Press the
PLAY button to return to playback.
NOTES:
•
You can advance the picture one frame at a time by pressing the PAUSE button during the Still mode.
•
If it is left in the Pause mode for more than five minutes, the TV/DVD/VHS will automatically switch to the Stop mode.
VERTICAL HOLD CONTROL
NOTE:
•
In Still mode, press the SLOW button and press the
CHANNEL K or L button until streaks disappear.
To return to Still mode, press the PAUSE button again.
In the Pause/Still mode only, when the picture begins to vibrate vertically, stabilize the picture by pressing the CHANNEL K or L button.
- 26 -
NOTE:
If there are video noise lines on the screen, see Tracking
Adjustment section.
EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 27
SPECIAL PLAYBACK
Make sure ...
•
TV/DVD/VHS power must be turned on.
•
Insert a prerecorded tape.
•
Before playback, follow steps below.
RENTAL PLAYBACK
This function enables you to improve the picture quality when playing back worn cassettes such as rented tapes.
AUTO REPEAT PLAYBACK
The TV/DVD/VHS has the auto repeat function that allows you to repeat a tape indefinitely without touching the PLAY button.
ALL REPEAT:
Repeat playback from the beginning to the end of the tape.
BLANK REPEAT
: Repeat playback from the beginning to a blank part, which is blank for more than
10 seconds.
1
Select “USER’S SET UP”
Press the SETUP button on the remote control.
Press the Arrow K or L button to point to “USER’S SET UP”.
Then, press the Arrow B button.
B
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
1
Select “USER’S SET UP”
Press the SETUP button on the remote control.
Press the Arrow K or L button to point to “USER’S SET UP”.
Then, press the Arrow B button.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Set “RENTAL” to [ON]
Press the Arrow K or L button to point to “RENTAL”.
Press the Arrow B or s button until [ON] appears.
– USER’S SET UP –
B RENTAL
REPEAT PLAY
AUTO RETURN
VCR AUDIO
TV AUDIO
[ON]
[OFF]
[OFF]
[HIFI]
[STEREO]
2
Select “ALL” or “BLANK”
Press the Arrow K or L button to point to “REPEAT PLAY”.
Press the Arrow B or s button repeatedly until your desired selection [ALL] or [BLANK] appears.
– USER’S SET UP –
B
RENTAL
REPEAT PLAY
AUTO RETURN
VCR AUDIO
TV AUDIO
[OFF]
[ALL]
[OFF]
[HIFI]
[STEREO]
3
Exit the Rental setting
Press the SETUP button on the remote control to return to the TV mode.
3
Exit the Repeat Play setting
Press the SETUP button on the remote control to return to the TV mode.
4
Start playback
Press the PLAY button to start playback. “RENTAL
PLAY B” appears.
•
Once you select the Rental mode, it stays in effect even after you turn off the TV/DVD/VHS.
4
Start playback
Press the PLAY button to start the Repeat Play.
”REPEAT PLAY B” appears.
•
Once you select the Repeat Play mode, it stays in effect even after you turn off the TV/DVD/VHS.
•
If the Rental mode is set [ON], the “RENTAL
PLAY B” display has priority.
TO CANCEL THE RENTAL MODE
Repeat steps [1] and [2], select [OFF] using the
Arrow B or s button on the remote control. Press the SETUP button on the remote control to return to
TV mode.
If there is a power failure of any kind, the unit will retain its memory for this feature.
TO CANCEL THE REPEAT PLAY MODE
Repeat steps [1] and [2], select [OFF] using the
Arrow B or s button on the remote control. Press the SETUP button on the remote control to return to
TV mode.
If there is a power failure of any kind, the unit will retain its memory for this feature.
- 27 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 28
SEARCH
Make sure ...
•
TV/DVD/VHS power must be turned on.
•
Insert a tape.
ZERO RETURN
This function allows you to search easily a beginning point that you want to review by rewinding or fast forwarding.
NOTE:
Zero Return WILL NOT work on a blank tape or a blank portion of a tape.
•
This function will not operate in recording mode.
•
This function is not operative when a cassette tape is not inserted in the TV/DVD/VHS.
In the example below: To watch a program after 2 hour 50 minutes from the present position, in either direction.
1
Insert a tape.
1
Stop a tape at your desired point
Rewind or fast forward the tape to the beginning point at which you want to review.
2
Reset the counter to 0:00:00
Press the C.RESET button repeatedly.
2
Select “TIME SEARCH” mode
Press the SETUP button on the remote control.
Press the Arrow K or L button to point to “TIME SEARCH”.
Then, press the Arrow B button.
B
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
3
Begin recording or playback
Press the RECORD or PLAY button.
Press the STOP button when recording or playback is completed.
4
To activate “ZERO RETURN” mode
Press the SETUP button on the remote control.
Press the Arrow K or L button to point to “ZERO RETURN”.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
B
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Then, press the Arrow B button.
The counter will appear on the TV screen.
The tape will automatically stop when the counter returns to 0:00:00.
3
Enter your desired time
Press the Arrow K or L button until your desired time appears.
(Example: “2:50” stands for 2 hours
50 minutes)
TIME SEARCH
2 : 50
If you wish to cancel the Time
Search at this point, press the SETUP button on the remote control.
4
Begin Time Search
By pressing the Arrow s or B button, the
TV/DVD/VHS will rewind or fast forward to the specified point.
The time counts down as the searching progresses.
When 0:00 is reached, the tape will start playback automatically.
TIME SEARCH
The Time Search function makes it possible to quickly advance the tape to your desired position simply by entering the exact amount of playback time you want to skip.
NOTES:
•
Time Search can be set up to a maximum of 9 hours 50 minutes (9:50) by 10 minutes at a time.
TO CANCEL THE TIME SEARCH at this point
Press the STOP/EJECT button on the TV/DVD/VHS or the remote control. This will delete the selected time.
- 28 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 29
INDEX SEARCH
This feature provides a method of indexing the starting point so that it can be easily returned to in either fast forward or rewind mode.
•
The index mark will be made automatically when the REC button is pressed. It will also be marked at the starting point of Timer recording and OTR.
•
The index mark will not be recorded if the PAUSE button is pressed and released during recording.
•
The time gap between making the index marks on the tape should be greater than 1 minute for SP recording, 2 minutes for LP recording and 3 minutes for SLP recording.
•
In some cases, the index mark at the beginning of video tape cannot be detected.
Example: You are watching program number 4 and want to fast forward to program number 7. You must skip three programs.
1
Select “INDEX SEARCH”
Press the SETUP button on the remote control.
Press the Arrow K or L button to point to “INDEX SEARCH”. Then, press the Arrow Bbutton.
B
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Enter your desired number
Press the Arrow K or L button until the number of programs that you want to skip appears.
(Example: “03” for 3 programs)
INDEX SEARCH
0 3
•
The Index Search mode will be canceled if the procedures are not activated in 30 seconds.
3
Begin Index Search
Press the Arrow s or B button. The TV/DVD/VHS begins rewinding or fast forwarding to the beginning of desired program.
NOTE: Every time an index signal is skipped, the number in the program indicator decreases by one.
CURRENT PLAYBACK PROGRAM
Beginning of tape
End of tape
4
Pro.1
Pro.2
Pro.3
Pro.4
Pro.5
Pro.6
Pro.7
3 2 1 1 2 3
INDEX MARK
4
After Index Search
When the preset program is reached, the
TV/DVD/VHS will start playback automatically.
•
A video cassette must be inserted in the
TV/DVD/VHS for this function to work.
•
The number of Index Searches can be set up to 20.
•
This function will not operate in the recording mode.
•
When you want to cancel the Index Search while in progress, press the STOP button.
SPECIAL FEATURES
REAL TIME TAPE COUNTER
This shows the elapsed recording or playback time in hours, minutes, and seconds. (The displayed time will not change on a blank tape or blank portions on the tape.)The “–” indication will appear when the tape has rewound further than “0:00:00” on the tape counter.
AUTO REWIND-EJECT
•
When the end of a tape is reached during recording, playback, or fast-forward, the tape will automatically rewind to the beginning. After rewinding finishes, the TV/DVD/VHS will eject the tape and turn itself to off.
•
This function is operative when Repeat Play is set to the [OFF] position.
•
The tape will not auto-rewind during timer recording or One Touch Recording.
- 29 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 30
RECORDING
Make sure ...
•
TV/DVD/VHS power must be turned on.
•
Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording.)
NOTES:
•
This unit will ONLY record and view the same channel.
•
This unit cannot record the contents from the built-in DVD.
NORMAL RECORDING
You can ONLY watch the same TV program that is being recorded.
1
Select the channel to be recorded
Press the number buttons on the remote control or the CHANNEL
K or L button.
CH 10
Remember: If the TV/DVD/VHS is connected to a cable box or satellite box, the TV/DVD/VHS must be on CH3 or CH4, then the channel to be recorded must be selected on the cable box or satellite box.
2
Select the tape speed
Press the SPEED button to select the desired tape speed (SP/ SLP).
SKIPPING UNWANTED
SCENES DURING RECORDING
Press the PAUSE button to temporarily stop recording.
PAUSE
Press the PAUSE or RECORD button to resume recording.
NOTES:
SP
•
After five minutes, the
TV/DVD/VHS will automatically switch to the
Recording mode to prevent tape damage.
•
If “CLOSED CAPTION (ON)” is selected, the On-
Screen Display will appear for 5 seconds, then disappear.
SP
3
Begin recording
Press the RECORD button.
REC
SP
4
Stop recording
Press the STOP button when recording is completed.
- 30 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 31
OTR (One Touch Recording)
This function enables you to set a recording length simply by pressing the REC/OTR button on the
TV/DVD/VHS.
Make sure ...
•
TV/DVD/VHS power must be turned on.
•
Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording.)
NOTES:
•
This function CANNOT be done from the remote control.
•
Recording starts immediately when the REC/OTR button is pressed.
•
When the REC/OTR button is pressed 18 times, the
TV/DVD/VHS returns to the Normal Recording mode.
•
To stop the OTR operation, press the STOP button on the TV/DVD/VHS or on the remote control.
•
To show the remaining time, press the DISPLAY button on the remote control so that “OTR” appears on the TV screen. (It will show up momentarily then disappear.)
•
Recording stops when 0:00 is reached.
•
Please note that in the SLP mode maximum recording time, assuming the tape is started at the beginning, is 8 hours using T-160 (or 6 hours using T-
120).
•
If the tape runs out before the end time, the
TV/DVD/VHS will switch to the Stop mode immediately, ejects the tape and turns itself off.
Push(es) Display
1 push
2 pushes
3 pushes
0:30
1:00
Recording length
(normal recording)
30 minutes
60 minutes
17 pushes 8:00
COPYING A VIDEO CASSETTE
(Requires a VCR or camcorder)
You can make copies of video tapes made by friends or relatives for your enjoyment.
WARNING: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws.
Connect your TV/DVD/VHS and a Source (Playing)
VCR using the following diagram.
[The TV/DVD/VHS]
[Fig.8]
HEADPHONE VIDEO L-AUDIO-R
480 minutes
Audio/Video adapter cable
(not supplied)
[Ex: Source (playing)
VCR or camcorder]
AUDIO
L
OUT IN
R
VIDEO
OUT IN
1
Select the channel to be recorded
Press the number buttons on the remote control or the CHANNEL K or L button.
Remember: If the TV/DVD/VHS is connected to a cable box or satellite box, the TV/DVD/VHS must be on CH3 or CH4, then the channel to be recorded is selected on the cable box or satellite box.
2
Select the tape speed
Press the SPEED button to select the desired tape speed (SP/ SLP).
3
Begin OTR
OTR(2 : 30)
Press the REC/OTR button on the
TV/DVD/VHS as many times as needed. The recording length will be determined by the number of
SP times you press the REC/OTR button. Each additional push will increase the recording time by 30 minutes. It is set up to 8 hours.
1)Insert a pre-recorded video cassette into the Source
(Playing) VCR or camcorder.
2)Insert a blank video cassette, or one you want to record over, into the TV/DVD/VHS’s cassette compartment.
3)Press the SPEED button on remote control for the
TV/DVD/VHS to select the desired recording speed (SP/SLP).
4)Press the CHANNEL K or L button on the
TV/DVD/VHS until “AUX” appears on the screen.
5)Press the RECORD button on the TV/DVD/VHS.
6)Begin playback of the tape in the source (Playing)
VCR or camcorder.
NOTE: For best results during copying, use the
TV/DVD/VHS’s front panel controls whenever possible. The remote control might affect the source
(Playing) VCR’s playback operation.
- 31 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 32
TIMER
AUTOMATIC TIMER
You may set the TV/DVD/VHS to start and end a recording while you are away. You can set 8 programs to record on specific days, daily or weekly within a 1 year period.
In the example below, the timer is being set to record:
DATE: July 5th, 2002
SETTING TIME: from 7:30PM to 8:50PM
CHANNEL: CH61
TAPE SPEED: SP
Make sure ...
•
If a cable box or satellite box is connected with the
TV/DVD/VHS you will be limited to record only one channel. And the channel selector on the
TV/DVD/VHS must be selected to the output channel of the boxes CH 3 or CH 4 and then the actual channel to be recorded must be selected on the boxes.
•
Clock must be set to the correct time and date before setting the timer.
•
TV/DVD/VHS power must be turn on to program it.
•
Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording.)
•
The channel you want to record is properly set in advance. (See page 16.)
Avoid over lap of programs ...
There is a chance that a program will not be recorded. when programs overlap;
•
The program with an earlier start has priority.
•
Once the earliest program finishes, the overlapping programs will begin recording in sequence.
•
The illustration below demonstrates the sequence of recordings.
Program 1
Program 2
Program 3
RECORDING
10:00AM - 11:00AM
9:00AM - 10:00AM
9:30AM - 12:00PM pressing the Arrow K button. And press the Arrow B button.
- TV/VCR SETUP -
•
If you have not yet set the clock,
“MANUAL CLOCK SET” appears. If so, follow stops [3] to
[8] on page 18. Then set the timer recording.
B TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Select your desired program position (1~8)
Press the Arrow K or L button to select the desired program position.
Then, press the Arrow B button.
– TIMER PROGRAMMING –
CH DATE BEGIN END
B
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
3
Set the channel number
– TIMER PROGRAMMING –
Press the Arrow K or L button until the desired channel number appears.
(Example: CH61)
CH DATE BEGIN END
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
B
61 -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
Then, press the Arrow B button.
Remember: If the TV/DVD/VHS is connected to a cable box or satellite box, the TV/DVD/VHS must be on CH3 or CH4, then the channel to be recorded is selected on the cable box or satellite box.
4
Select once, every day or
– TIMER PROGRAMMING –
CH DATE BEGIN END
weekly recording
For once recording :
B
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
61 7/05 FRI -:- -
- -/- - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
Press the Arrow K (up) button until the desired date appears.
(Example: “7/05” for July 5th). Then, press the
Arrow B button.
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
For every day recording : To record a TV program at the same time on the same chan-
– TIMER PROGRAMMING –
nel every day. (Example: Monday
CH DATE BEGIN END
through Sunday)
Press the Arrow L (down) button until “EVRY DAY” appears.
B
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
61 EVRY DAY -:- -
- - -/- - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
Then, press the Arrow B button.
Recording Sequence
Program 1
10:00AM-11:00AM
Program 2
9:00AM-10:00AM
Program 3
9:30AM-12:00PM
9:00AM 10:00AM 11:00AM
*Recording period is SHADED
12:00PM
1
Select “TIMER PROGRAMMING”
Press the SETUP button on the remote control.
Confirm “TIMER PROGRAMMING” is pointed by
- 32 -
For weekly recording : To record a TV program at the same time on the same channel
– TIMER PROGRAMMING –
every week. (Example: every
CH DATE BEGIN END
Monday)
Press the Arrow L (down) button until “EVRY” and your desired
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
B
61 EVRY MON -:- -
- - -/- - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - day of the week appear together. Then, press the
Arrow B button.
EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 33
5
Set beginning hour
– TIMER PROGRAMMING –
CH DATE BEGIN END
Press the Arrow K or L button until the desired hour appears.
(Example: “ 7, PM” for 7:30PM)
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
P
M B
61 7/05 FRI 7:12
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
Then, press the Arrow B button.
6
Set beginning minute
– TIMER PROGRAMMING –
Press the Arrow K or L button until the desired minute appears.
(Example: “30” for 7:30PM)
Then, press the Arrow B button.
CH DATE BEGIN END
B
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
61 7/05 FRI 7:30
P
M
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
7
Set end hour
– TIMER PROGRAMMING –
CH DATE BEGIN END
Press the Arrow K or L button until the desired hour appears.
(Example: “8, PM” for 8:50PM)
Then, press the Arrow B button.
B
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
61 7/05 FRI 7:30
P
M
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
-:- - - -
-:- - - -
-:- - - -
8:30
P
M
- -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
TIMER PROGRAM EXTENSION
To shift the time schedule of an automatic timer recording.
1)Press the POWER button.
2)Repeat step [1] on page 32.
3)Press the RECORD button and select the desired program using the Arrow K or L button.
4)Press the RECORD button again.
Each additional push will shift forward the begin/end time for recording by 10 minutes. When the recording is already in progress, each additional push will shift forward the end time only. If you want to cancel while setting, press the PAUSE button on the remote control. The recording time returns to the original time.
NOTE: When you shift forward the time schedule during recording, the recording speed will automatically be set to the SLP mode.
5)Press the Arrow B or s button to exit the setting menu. Then press the SETUP button on the remote control to return to original mode.
8
Set end minute
Press the Arrow K or L button until the desired minute appears.
(Example: “50” for 8:50PM)
Then, press the Arrow B button.
– TIMER PROGRAMMING –
CH DATE BEGIN END
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
P
M B
61 7/05 FRI 7:30
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
-:- - - -
-:- - - -
-:- - - -
P
M
8:50 - -
-:- - - -
-:- - - -
-:- - - -
-:- - - -
9
Set the tape speed
Press the Arrow K or L button until the desired tape speed appears. (Example: SP)
– TIMER PROGRAMMING –
CH DATE
B
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
61 7/05 FRI 7:30
P
M
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
- -/- - - - -:- -
BEGIN END
-:- - - -
-:- - - -
-:- - - -
8:50
P
M
SP
-:- - - -
-:- - - -
-:- - - -
-:- - - -
10
Finish setting the program
Press the Arrow B or s button. The program is now completed.
•
To set another program, repeat steps [2] to [10].
•
Press the SETUP button on the remote control to return to original mode.
TO CORRECT A PROGRAM
•
While setting a program; press the Arrow s button to go back one step and enter the correct numbers using the Arrow K or L button.
•
After setting a program;
1)Press the POWER button.
2)Repeat steps [1] - [2] on page 32.
3)Press the Arrow B button (or press the Arrow s button to go back one step) until the part you want to correct begins flashing, then make the changes pressing the Arrow K or L button.
4)Press the POWER button to set automatic timer recording.
11
Set the timer
Press the POWER button to set automatic timer recording. The TIMER REC indicator lights up.
•
You must turn off the TV/DVD/VHS to activate automatic timer recording.
If power is not turned off and you continue watching TV, “TIMER REC STANDBY” starts flashing on the TV screen 2 minutes before the programmed start time.
TO CANCEL AN AUTOMATIC TIMER
RECORDING
•
After setting a program;
1)Press the POWER button.
2)Repeat steps [1] ~ [2] on page 32 and select a program you want to cancel.
3)Press the C.RESET button.
4)Press the SETUP button on the remote control to return to TV mode.
•
While recording is in progress;
1)Press POWER button.
2)Press the STOP/EJECT button on the
TV/DVD/VHS.
- 33 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 34
TO CHECK THE BEGIN/END TIME
1)Press the POWER button so that the REC indicator goes off.
2)Press the SETUP button on the remote control.
3)Confirm “TIMER PROGRAMMING” is pointed.
4)Press the Arrow B button. The details of programs appear on the TV screen.
5)Press the SETUP button on the remote control to return to TV mode.
HINTS FOR AUTOMATIC
TIMER RECORDING
•
Make sure the channel you want to record is properly set in advance.
•
It is not necessary to press the RECORD button for timer recording.
•
Recording begins automatically at the Start time.
•
If you are recording using a Timer mode, you may not operate the unit manually.
•
The erase-prevention tab on the cassette must be in place (or you must put tape over the hole).
•
If the erase-prevention tab is removed, the cassette will be ejected when the POWER button is pressed to off.
•
If the tape runs out before the end time, the
TV/DVD/VHS will switch to the Stop mode immediately, and the tape will be ejected.
3
Auto Return will begin
When all the timer recordings are completed, the
TV/DVD/VHS will rewind to the beginning of the recorded program(s).
NOTE:
•
If you press the POWER button while tape is rewinding, the Auto Return will stop.
4
Watch the recorded program
Press the PLAY button.
TO CANCEL THE AUTO RETURN
MODE
Repeat steps [1] and [2], select [OFF] using the
Arrow B or s button.
If there is a power failure of any kind, the unit will retain its memory for this feature.
SLEEP TIMER
The Sleep Timer function turns off the
TV/DVD/VHS without using the POWER button after a desired period of time.
NOTE:
•
This function does not operate during Recording mode.
AUTO RETURN
With this feature, after timer recording is finished, the beginning of the recorded program(s) can be searched for automatically.
1
Select “SLEEP TIMER”
Press the SLEEP button on the remote control until
“SLEEP TIMER” appears.
1
Select “USER’S SET UP”
Press the SETUP button on the remote control.
Press the Arrow K or L button to point to “USER’S SET UP”.
Then, press the Arrow B button.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Set “AUTO RETURN” to [ON]
Press the Arrow K or L button to point to “AUTO RETURN”.
Press the Arrow B or s button until [ON] appears.
– USER’S SET UP –
RENTAL
REPEAT PLAY
B
AUTO RETURN
VCR AUDIO
TV AUDIO
[OFF]
[OFF]
[ON]
[HIFI]
[STEREO]
2
Set sleep time
Press the SLEEP button until your desired sleep time appears.
Each additional push will increase the time by 30 minutes up to 120 minutes.
After 5 seconds, exit the Sleep
Timer setting.
SLEEP 120 MINUTES
TO CANCEL THE SLEEP TIMER
Press the SLEEP button on the remote control until
“SLEEP TIMER” appears. Press the SLEEP button until “SLEEP 0 MINUTES” appears.
- 34 EN
1C29
TD360_01-35 02.2.13 9:57 AM Page 35
ON SCREEN DISPLAY
To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:
When the Closed Caption mode is OFF:
•
Counter mode: After 5 seconds, only the counter remains. To clear it, press the DISPLAY button.
•
Clock mode: After 5 seconds, only the clock and the channel number remain. To clear them, press the DISPLAY button.
When the Closed Caption mode is ON:
•
The On Screen Display disappear after 5 seconds.
•
This is true even if the MUTE button is pressed, or the PAUSE button is pressed while recording.
OFF mode Counter mode
STOP
Clock mode
STOP 5:40PM
CH2
OFF mode Clock/Counter mode
STOP 5:40 PM
CH2
SP COUNT 0:12:34
After 5 seconds
SP
After 5 seconds
5:40PM
CH2
SP COUNT 0:12:34
COUNT 0:12:34
Counter remains
Clock & Channel remains
CABLE CHANNEL DESIGNATIONS
If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels with letters or letter-number combinations. Please check with your local cable company. The following is a chart of common cable channel designations.
CATV channel
TV Display
CATV channel
TV Display
5A
1
C
16
2
2
D
17
3
3
E
18
4
4
F
19
5
5
G
20
6
6
H
21
7
7
I
22
8
8
J
23
9
9
K
24
10
10
L
25
11
11
M
26
12
12
N
27
13
13
O
28
A
14
P
29
CATV channel R S T U V W W+1 W+2 W+3 W+4 W+5 W+6 W+7 W+8 W+9
TV Display 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45
CATV channel
W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24
TV Display 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
CATV channel
W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39
TV Display
CATV channel
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75
W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54
TV Display 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90
CATV channel
TV Display
W+55 W+56 W+57 W+58
91 92 93 94
A-5
95
A-4
96
A-3
97
A-2
98
A-1
99
W+59 W+60 W+61 W+62 W+63 W+64
100 101 102 103 104 105
CATV channel
W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79
TV Display 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120
CATV channel
W+80 W+81 W+82 W+83 W+84
TV Display 121 122 123 124 125
B
15
Q
30
- 35 EN
1C29
TD360_35-55 02.2.13 9:58 AM Page 36
DVD SECTION
ABOUT THE DISCS
PLAYABLE DISCS
The following discs can be played back on this DVD player.
Disc Type
DVD
Video
Audio
CD
Logo Contents
Sound and
Pictures
Sound
Disc Size
12 cm
8 cm
Maximum
Playback Time
Approx. 4 h
(single-sided)
Approx. 8 h
(double-sided)
Approx. 80 min
(single-sided)
Approx. 160 min
(double-sided)
74 min 12 cm
8 cm
(singles)
20 min
This player conforms to the NTSC color system. You cannot play discs recorded in other color systems such as
PAL or SECAM.
¡ Some discs include region codes as shown below.
¡
Photo CD
(Never play back, otherwise malfunction may result.)
¡
Video CD
(Never play back, otherwise malfunction may result.)
Any other discs without compatibility indications
DISC TYPES
[DVD]
Data on a DVD is divided into sections called "titles", and then into subsections called "chapters", each of which is given a title or chapter number. Playback conditions are preset on some DVD video discs, and these playback conditions take priority over user operations on this player. If a function you selected do not run as desired, refer to the manual accompanying the disc.
Example
Title 1 Title 2
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2
¡ The number inside the symbol refers to a region of the world, and a disc encoded in a specific region format can only be played back on DVD players with the same region code.
The following discs cannot be played back on this
DVD player.
¡
DVD with region codes other than 1 or ALL.
¡
DVD-ROM
¡
DVD-RAM (Never play back, otherwise malfunction may result.)
¡
CD-ROM
¡
VSD
¡
CDV (Only plays back the audio part.)
¡
CD-G (Only plays back the sound.)
¡
CD-R
(Never play back, otherwise malfunction may result.)
¡
CD-I
(Never play back, otherwise malfunction may result.)
[AUDIO CD]
Data on an audio CD is divided into sections called
“tracks”, each of which is given a track number.
Example
Track 1 Track 2 Track 3 Track 4 Track 5 Track 6
– 36 – EN
01A11
TD360_35-55 02.2.13 9:58 AM Page 37
PLAYING A DISC
PLAYING A DVD VIDEO
OR AN AUDIO CD
DVD CD
Getting started
Turn on the power of the TV, amplifier and any other components which are connected to the DVD player.
(Change the input system to suit the DVD player, and check that the sound volume is correct.)
¡
If a disc is dirty or has scratches, the pictures may appear distorted and the playback operation may stop. In such cases, clean the disc and unplug the power cord and then plug it again before resuming playback.
¡
With DVDs that use some titles for playback program signals, playback may start from the second title, or it may skip these titles.
USING THE DVD MENUS
1
Press the POWER button.
¡ The power will turn on.
2
Press the OPEN/CLOSE button.
¡ The disc loading tray will open.
DVD
Some DVDs contain their own menus, such as a guidance menu which describes the contents of the disc or a selection menu for sound, language and other customized settings.
3
Place a disc into the tray.
¡
Make sure the disc is sitting properly in the correct recess, with the label side up.
1
Press the DISC MENU button.
¡
The DVD menu will appear.
2
Select the desired title.
¡
Press the arrow buttons ( L / K /B/s) to change the setting, and then press the ENTER button.
3
Playback will start from the selected title.
USING THE TITLE MENU
4
Press the PLAY button.
¡
The tray will close automatically, and playback will then start from the first chapter or track of the disc.
You need to press the PLAY button only when the tray has been closed by pressing the OPEN/CLOSE button.
DVD
With a DVD containing a title menu, you can select desired titles from the menu.
¡
When you play back the DVD which a title menu is recorded, the menu may appear on the screen. In this case, refer to “USING THE TITLE MENU”.
1
Press the TITLE button.
¡
The title menu will appear.
5
Press the STOP button to stop play.
2
Select the desired title.
¡ Press the arrow buttons ( L / K /B/s) to change the setting, and then press the ENTER button.
Notes
¡
If you press the OPEN/CLOSE button in the
TV/VCR mode or power-off, the DVD tray will open.
CALLING UP A MENU SCREEN
DURING PLAYBACK
¡
If you press the DVD side PLAY button in the
TV/VCR mode or power off, you can start the DVD playback.
¡ A “prohibited icon” may appear at the top-right on the TV screen during operation, warning that a prohibited operation has been encountered by the DVD player or the disc.
For DVDs
¡
¡
Press the DISC MENU button to call up the DVD menu.
Press the TITLE button to call up the title menu.
Note
¡ Contents of menus and corresponding menu
– 37 – operations may vary between discs. Refer to the manual accompanying the disc for details.
EN
01A11
TD360_35-55 02.2.13 9:58 AM Page 38
RESUMING PLAYBACK FROM
THE POINT WHERE
PLAYBACK STOPPED
DVD CD
2
Press the PLAY button to return to normal playback speed.
1
Press the STOP button during playback.
¡
Playback will stop, and then appear the resuming message at the center.
Press 'PLAY' to play from here
To play beginning, press 'STOP' first and the 'PLAY'.
PAUSING PLAYBACK OR
DISPLAYING A STILL PICTURE
DVD CD
2
Press the PLAY button. Playback will start from the point where the previous playback session was stopped.
Play B
1
Press the PAUSE button during playback.
¡ Playback will pause, with sound muted.
Pause F
2
Press the PLAY button to resume playback.
Notes
¡ Resuming playback is not available with some discs.
¡ It is possible to switch from the DVD play mode to the TV mode. Even if the power is turned off, the resume function enables to playback on from the previously interrupted point. But note that the
Marker commands are not saved.
¡
The resume function can be reset by pressing the
STOP button twice or by opening the disc loading tray.
Play B
STEPPING THROUGH FRAMES
DVD
FAST FORWARD/REVERSE
DVD CD
1
Press the PAUSE button while playback is paused.
¡
The next picture frame is displayed with sound muted each time the button is pressed.
Pause F
1
Press and hold the
g
or
h
button for more than 1 second during playback.
¡
For DVDs, pressing and more than 1 second holding the g or h button cycles the playback speed in three steps.
¡
For audio CDs, the playback speed is
×16 fixed.
REV E Button
E x2
FWD
D Button
D x2
2
Press the PLAY button to resume playback.
Play B
E x8
E x32
D x8
E x32
– 38 – EN
01A11
TD360_35-55 02.2.13 9:58 AM Page 39
SLOW MOTION
STARTING FROM A DESIRED
TIME COUNT
DVD
DVD CD
1
Press and hold the
g
button for more than
1 second while playback is paused. (Sound remains muted.)
¡ Slow motion mode will be activated.
¡ Pressing and holding the g button for more than
1 second cycles the playback speed in three steps.
Select an appropriate speed while referring to the speed indication on the screen.
1
Press the SEARCH MODE button.
¡
Press the button twice.
Search
Time _:__:__
Total Time 1:29:00
×1/16 ×1/8
D
Button
×1/2
2
Press the PLAY button to return to normal playback speed.
Notes
¡
Slow playback is not available with audio CDs.
¡
The reverse of slow playback is not available.
¡ If you press the g button and release immediately during playback is paused or slow, it returns to normal playback.
2
Press the numeric buttons to set the desired time count.
Search
Time _:__:__
Total Time 1:29:00
¡ Example: 1 hour, 23 minutes and
30 seconds
1
→ 2 → 3 → 3 → 0
Notes
¡ In the case of DVD, Time Search in Title is effective. (But Time Search in Chapter is ineffective.)
¡
In the case of CD, Time Search in Track is effective.
(But Time Search in the entire disc is ineffective.)
¡ Playback from a desired time count is not available with some discs.
¡
Specific time playback is not available with some discs or if the unit is in stop mode.
PLAYING FROM A DESIRED
TITLE OR CHAPTER
STARTING FROM A DESIRED
TRACK
CD
DVD
You can also press the SEARCH MODE button, use the numeric buttons to enter the chapter number.
¡
Perform the title search and the chapter search after setting them on the same screen at the same time.
Changeover by K / L buttons.
Search
Title : 1 / 4
Chapter:__ / 17
1
Press the SEARCH MODE button.
U se the numeric buttons to enter the track number. When the track number is entered in the entry box, playback of the desired track will start automatically.
Search
Track: __ / 26
Note
¡ Playback from a desired title or chapter is not available with some
DVDs.
TRICKS WITH THE SKIP BUTTONS (
H
, G)
If the SKIP button G is pressed during playback or while playback is paused, the current track is skipped and the next track is played. When the SKIP button H is pressed once, the top of the current track is located for replaying. When the SKIP button
H is pressed again while Within 2-second playback, the previous track is located.
– 39 – EN
01A11
TD360_35-55 02.2.13 9:58 AM Page 40
REPEAT A-B REPEAT
DVD DVD CD CD
1
Press the REPEAT button.
For DVDs
¡ A single title or chapter is played back repeatedly.
¡
Pressing the REPEAT button cycles the display on the screen as follows.
Repeat
[Title]
The current Title is played back repeatedly.
You can define a section to be played back repeatedly.
1
Press the A-B REPEAT button during playback.
¡ The starting point (A) will then be selected.
Repeat
[ A - ]
Repeat
[Chapter]
The current Chapter is played back repeatedly.
Repeat
[Off]
No repeat playback.
2
Press the A-B REPEAT button again at the end point (B) of the desired section.
¡ The selected section will be played back repeatedly.
Repeat
[ A - B ]
For audio CDs
¡
The whole disc or a single track is played back repeatedly.
¡ Pressing the REPEAT button cycles the display on the screen through All, Repeat Track and Off.
3
To exit A-B repeat playback, press the A-B
REPEAT button and set it to OFF.
Repeat
[ off ]
Repeat
[All]
Repeat
[Track]
Repeat
[Off]
The whole Disc is played back repeatedly.
The current Track is played back repeatedly.
No repeat playback.
If the REPEAT button is pressed once during program/random playback, the program/random playback is performed repeatedly.
If the REPEAT button is pressed again, the current track is played back repeatedly.
Notes
¡
With DVDs, the A-B repeat section can be set only within the current title.
¡
With audio CDs, the A-B repeat section can be set within the current track.
¡ A-B repeat is not available with some scenes in
DVD.
¡
To cancel the A point which was set, press RETURN button.
Notes
¡
Repeat playback is not available with some discs.
¡ The REPEAT setting will be cleared when moving to other title, chapter or track.
– 40 – EN
01A11
TD360_35-55 02.2.13 9:58 AM Page 41
PROGRAM (Audio CD) RANDOM (Audio CD)
CD
1
Press the MODE button in stop mode.
¡ The program screen will appear.
Audio CD
Program
Total
[Track]
– –
[Time]
0:00:00 Track 00 / 15
Start : PLAY
Random : MODE
Delete : CLEAR
Exit : RETURN
1
Press the MODE button in stop mode.
¡
The program setting menu screen will appear.
2
Press the MODE button again.
Audio CD
Random
CD
2
Press the numeric buttons to enter the desired track numbers.
¡ The total playback time for the selected tracks will appear on the
TOTAL line.
Audio CD
Program
Total
[Track]
12
[Time]
0:47:29
02 05 07 14 01 09 13 10 03 11
08 04
Track 04 / 15
Start : PLAY
Random : MODE
Delete :
Exit :
CLEAR
RETURN
Start : PLAY Exit : MODE
3
Press the PLAY button. Random playback will then start.
Note
¡
Program playback is not available during random playback.
3
Press the PLAY button.
¡
Playback will start in the programmed order.
¡
While the program is being played back, the STOP button works as follows.
ZOOM PLAYBACK
(enlargement onscreen)
¡ Press the STOP button once and then the PLAY
DVD
button again, playback will restart from the point where the STOP button was pressed. (Program continued)
Images can be enlarged four times on the screen to your taste.
¡ Press the STOP button twice and then the PLAY button again, playback will restart from the first tune
Press the ZOOM button during playback.
in the program in the usual way. (Program
¡ An image will be enlarged at the center of the continued) screen.
¡
Press the STOP button three times and then the
PLAY button again, playback will restart from the
¡ Press the ZOOM button again, and the image will be track in the usual way. (Program cleared) back to the previous size.
Zoom [on]
Notes
¡ Adding programs is not possible during program playback. You must stop the current playback before such operations can be carried out.
¡
Press the CLEAR button to cancel a program. The most recently entered program will then be deleted.
¡ Numbers which exceed the number of tracks on the disc in the tray are not accepted.
¡
Playback from a desired track and random playback are not available during program playback.
¡
Program settings are cleared when the power is turned off or the disc loading tray is opened.
¡ If the track no. is once set in the program, the setting cannot be changed.
When the cursor (
K / L / s / B
) button is pressed during zoom play, the part to be zoomed moves.
¡ The zooming frame can be moved from the center
.... 4 steps to the right. 4 steps to the left. 4 steps to the top. 4 steps to the bottom.
– 41 – EN
01A11
TD360_35-55 02.2.13 9:58 AM Page 42
Note
¡
Zooming function does not work while operation display screen is shown.
SETTINGS
CHANGING THE AUDIO
LANGUAGE OR SOUND MODE
For DVDs
DVD
Notes
¡ Pressing the Audio button may not work on some
DVDs with multiple audio languages (e.g. DVDs which allow audio language setting on the disc menu). Operation varies between discs, so refer to the manual accompanying the disc.
The DVD player has a function which allows you to select the desired audio language and sound mode.
¡
If a desired language is not shown after pressing the
Audio button several times, the disc does not have an audio source in that language.
Press the AUDIO button during playback, and then press the AUDIO button to select the desired audio language.
¡ The audio language can be changed if multiple languages are recorded on the DVD being played.
¡ The audio language resets to the one which has been selected in the setup mode, every time the power is turned on or discs are replaced. If that language is not available on a disc, a language defined by the disc is selected.
Audio 1 , English / 8
¡ The screen display will disappear after about 5 seconds.
Audio 2 , French / 8
Audio 8 , Japanese / 8
Bonjour
HELLO
– 42 – EN
01A11
TD360_35-55 02.2.13 9:58 AM Page 43
CHANGING THE SUBTITLE
LANGUAGE
DVD
CHANGING THE CAMERA
ANGLE (Multi-Angle Pictures)
DVD
The DVD player has a function which allows you to select the desired language for subtitles.
The DVD player has a function which allows you to select the desired camera angle.
Press the SUBTITLE button during playback, and then press the SUBTITLE button to select the desired subtitle language.
¡ The subtitle language can be changed if the subtitles are recorded in multiple languages on the DVD being played.
¡ The subtitle language cannot be changed if the subtitles are recorded in a single language on the
DVD being played.
1
Press the ANGLE button during playback.
¡ If the disc contains sequences recorded from different camera angles, the angle icon ( ) will appear at the top-right of the screen. You can change the camera angle when the icon appears on the screen.
¡ The camera angle cannot be changed if the disc does not contain sequences recorded from different camera angles.
Subtitle 1 , English / 8
Subtitle 1
Subtitle 2 , French / 8
Subtitle 2
2
Press the ANGLE button while the angle number is shown on the screen.
Angle 1 / 8
Angle 1
Angle 2 / 8
Angle 2
Subtitle Off
No subtitles
Angle 8 / 8
Angle 8
HELLO
Bonjour
¡
Pressing the SUBTITLE button cycles the subtitle language from SUBTITLE 1, SUBTITLE 2 and all the languages recorded through to off.
Note
¡
The screen display will disappear after about 5 seconds.
Notes
¡ Some discs allow subtitle language setting on the disc menu. (Operation varies between discs, so refer to the manual accompanying the disc.)
¡
If the desired language is not shown after pressing the SUBTITLE button several times, the disc does not have subtitles in that language.
¡
The subtitle language resets to the one which has been selected in the setup mode, every time the power is turned on or discs are replaced. If that language is not available on a disc, a language defined by the disc is selected.
¡ It may take time to display the subtitles in the selected language.
¡
The screen display will disappear after about 5 seconds.
¡ When “Subtitle Not Available” appears onscreen, it means no subtitle is recorded on the scene.
– 43 – EN
01A11
TD360_35-55 02.2.13 9:58 AM Page 44
CHANGING THE ON-SCREEN
DISPLAY
For DVDs
For audio CDs and DVDs
1
2
For audio CDs
Kind of disc in playbacking
Current playback status
Current repeat status
Current track number
Nomal playback
Programedplayback
Random playback
[Track]
Elapsed time of the current track and
Remaining time of the current track.
[All]
Elapsed time of the current disc and
Remaining time of the current disc.
Playback Setup Window (CD)
ITEM
Track
Time
Marker
DVD CD
You can check the information about the disc by pressing the DISPLAY button on the remote control.
Press the DISPLAY button, the display appears on the screen.
For the selecting the item of the Playback Setup
Window, press the K/L button to select the item, then press the ENTER button.
Audio CD
Play
Repeat
[Track]
Track
2
Play Mode
Normal
Time
[Track]
0:01:46
-0:03:27
01 02 03 04 05 06 07 08 09 10
11 12
Track 2 / 12
Time 0:05:13
Maker ...
Time Display Track
Info. Window
Playback Setup Window
DISPLAY CONTENTS
Current track number / the number of total tracks
Total time of the current track
Place the cursor and press the ENTER button to activate the Marker function.
[Set the marker]
Using
K
/
L button, position the cursor on to the marker number shown as “Not
Set”. Press the ENTER button when the screen to be reviewed appears.
Up to 5 points can be marked.
[Call back the marker]
Using
K
/
L button, position the cursor on to the marker number to be called back and press the ENTER button.
[Clear the marker]
Using
K
/
L button, position the cursor on to the marker number to be cleared and press the CLEAR button.
To clear all markers, place the cursor on
“All Clear Markers” and press the
ENTER button.
Kind of disc in playbacking
Current playback status
Current repeat status
Current title number
Current chapter number
Elapsed time of the current title and
Remaining time of the current title.
DVD
Play
Repeat
[Chapter]
Title
1
Chapter
18
Time
0:17:52
-1:38:46
Bit Rate
Picture in play back
•
Chapter
Title
Time
Audio
18 / 30
1 / 5
1:56:38
1.English / 4
Info. Window
Playback Setup Window
Playback Setup Window (DVD)
ITEM
Chapter
Title
Time
Audio
Subtitle
Angle
Marker
DISPLAY CONTENTS
Current chapter number / the number of total chapters
Current title number / the number of total titles
Total time of the current title
Audio No., audio language / the number of available audio languages in the disc
Subtitle No., subtitle language / the number of available subtitle languages in the disc
Off : Subtitle is not displays.
Not Available : Subtitle is not included.
Angle No. / total number of the angles
1/1 : Multi angle is not included in the disc.
Place the cursor and press the ENTER button to activate the Marker function.
[Set the marker]
Using
K
/
L button, position the cursor on to the marker number shown as “Not
Set”. Press the ENTER button when the screen to be reviewed appears.
Up to 5 points can be marked.
[Call back the marker]
Using
K
/
L button, position the cursor on to the marker number to be called back and press the ENTER button.
[Clear the marker]
Using
K
/
L button, position the cursor on to the marker number to be cleared and press the CLEAR button.
To clear all markers, place the cursor on
“All Clear Markers” and press the
ENTER button.
SRS
TruSurround
The current setting (On/Off) is displayed.
To exit the display (DVD and CD):
Press the RETURN button.
In the playback Setup Window, press the RETURN button to change the present indication to the former one.
– 44 – EN
01A11
TD360_35-55 02.2.13 9:58 AM Page 45
CHANGING THE SETUP ITEMS
Note
¡ When you change the setup items, press the STOP button if you are in playback mode.
(The on-screen display appears in selected language.)
LANGUAGE SETTINGS
1
Press the SETUP button.
¡
The setup screen appears.
2
Press the
Language
Display
Audio
Parental
Select : / Set : ENTER
Cancel : Exit : SETUP
K / L
buttons to select Language, and then press the ENTER button.
Language
Display
Audio
Language Controls
Audio English
Subtitle English
Disc Menu
Player Menu
English
English
Player Menu
English
Français
Español
P l
4
Press the
K / L
buttons to select a desired item, and then press the ENTER button.
¡
If Other is selected on the Audio, Subtitle or Disc
Menu setting screen, the Language Code setting screen will appear. Press the numeric buttons to enter the desired language code while referring to the list on page 49.
Language
Language Controls
Audio English
Subtitle
Disc Menu
Player Menu
English
English
English
Display
Language
Language Controls
Audio
Subtitle
English
English
Disc Menu
Player Menu
English
English
Display
Audio
Parental
Audio
Irish
Portuguese
Dutch
Other _.......
o
S l t / S t ENTER
3
Press the
K / L
buttons to select an item, and then press the ENTER button.
(Voice is played back in selected language.)
5
Press the SETUP button.
¡ The setup mode will be canceled and the ordinary screen will appear.
Language
Display
Audio
Language Controls
Audio English
Subtitle
Disc Menu
Player Menu
English
English
English
Audio
Original
English
French
Spanish p
P l
(Subtitles are shown in selected language.)
Note
¡ Language Setting for Audio and Subtitle is not available with some discs. Then use the Audio and
Subtitle button. Details are on pages 42 and 43.
Language
Display
Audio
Language Controls
Audio English
Subtitle
Disc Menu
Player Menu
English
English
English
Subtitle
Off
English
Spanish
French p
(The disc menu appears in selected language.)
Language
Display
Audio
Language Controls
Audio English
Subtitle
Disc Menu
Player Menu
English
English
English
Disc Menus
Original
English
French
Spanish p
– 45 – EN
01A11
TD360_35-55 02.2.13 9:58 AM Page 46
DISPLAY SETTINGS
Background Color (Default : Gray)
Select gray or blue.
1
Press the SETUP button.
¡
The setup screen will appear.
Language
Display
Audio
Parental
Select : / Set : ENTER
Cancel : Exit : SETUP
Language
Display Controls
On Screen Info On
Angle Icon On
Background Color Gray
Auto Power Off On
Display
o
2
Press the
K / L
buttons to select Display and then press the ENTER button.
Auto Power Off (Default : On)
Set or not set to turn off after the screen saver is started and no keys are pressed for 30 minutes.
Language
Display Controls
On Screen Info
Angle Icon
On
On
Background Color Gray
Auto Power Off On
Display
o
Language
Display Controls
TV Aspect 4:3 Pan & Scan
On Screen Info On
Angle Icon On
Background Color Gray p
Display
4
Press the
K / L
buttons to select a desired item, and then press the ENTER button.
3
Press the
K / L
buttons to select an item, and then press the ENTER button.
TV Aspect
(Default : 4:3 Pan & Scan)
4:3 Pan & Scan : Full height picture, trimmed both sides
4:3 Letter Box : Wide screen with black bars on top and bottom
5
Press the SETUP button.
¡
The setup mode will be canceled and the ordinary screen will appear.
Language
Display
Audio
Display Controls
TV Aspect 4:3 Pan & Scan
On Screen Info On
Angle Icon On
Background Color Gray p
TV Aspect
4:3 Pan & Scan
4:3 Letterbox
Notes
• Some discs do not contain pan and scan images.
• Some discs do not contain letter box images.
On Screen Info (Default : On)
Display or not display the disc status (Example “PLAYB”).
Language
Display Controls
TV Aspect 4:3 Pan & Scan
On Screen Info On
Angle Icon On
Background Color Gray p
Display
Angle Icon (Default : On)
Display or not display the Angle icon on the screen.
Language
Display Controls
TV Aspect 4:3 Pan & Scan
On Screen Info On
Angle Icon On
Background Color Gray p
Display
– 46 – EN
01A11
TD360_35-55 02.2.13 9:58 AM Page 47
AUDIO SETTINGS
1
Press the SETUP button.
¡
The setup screen will appear.
2
Press the
Language
Display
Audio
Parental
Select : / Set : ENTER
Cancel : Exit : SETUP
K / L
buttons to select Audio and then press the ENTER button.
Dolby Surround: When the unit is connected to an audio component that conforms to
Dolby Surround Pro Logic
Stereo: When the unit is connected to a normal audio component
Down Sampling (Default : 48kHz)
Set the output for the DVD recorded in PCM 96kHz
(96kHz or 48kHz)
To select Down
Sampling 48kHz or
Language
Display
Audio Controls
Digital Audio Out ...
Dynamic Range On
Downmix Mode Dolby Surround
Down Sampling 48kHz
96kHz, press the
ENTER button repeatedly.
Language
Audio Controls
Digital Audio Out ...
Dynamic Range On
Downmix Mode Dolby Surround
Down Sampling 48kHz
Display
3
Press the
K / L
buttons to select an item, and then press the ENTER button. (Choose
Digital Audio Out and press the ENTER button to set Dolby Digital, DTS, and MPEG. Go to step 4.)
4
Press the
K / L
buttons to select a desired item, and then press the ENTER button.
¡ If PCM, Dolby Digital or DTS MPEG is selected on the Digital Audio Out setting screen, press the K / L buttons again to select a further item, and then press the ENTER button.
Digital audio out setting (Next step)
Language
Display
Audio
Audio Controls
Digital Audio Out ...
Dynamic Range On
Downmix Mode Dolby Surround
Down Sampling 48kHz
Digital Audio Out
Dolby Digital Off
DTS Off
MPEG Off
Downmix Mode
(Default: Dolby Surround)
Language
Audio Controls
Digital Audio Out ...
Dynamic Range On
Downmix Mode Dolby Surround
Down Sampling 48kHz
Display
If you select Digital
Audio Out, the screen changes to step 4. If you want to set other items of step 3, press the K / L buttons.
Dynamic Range (Default : Off)
On : Dynamic range is available
To select Dynamic
Language
Audio Controls
Digital Audio Out ...
Dynamic Range On
Downmix Mode Dolby Surround
Down Sampling 48kHz
Range On or Off, press the ENTER
Display
button repeatedly.
¡ This function is for controlling the range of sound volume. By compressing the range of sound volume, it is possible not only to suppress the output of loud sound at night and but also to raise the volume of low sound.
¡
However, this function is effective only for the sound recorded by Dolby Digital recording. When the sound recorded by Dolby Digital 5.1ch is outputted, the sound is compressed automatically even with this function being set at “Off ”.
Dolby Digital (Default : Off)
On : Output by Dolby Digital.
Set to On when the unit is connected to Dolby Digital
Decoder.
Language
Display
Audio
Audio Controls
Digital Audio Out ...
Dynamic Range On
Downmix Mode Dolby Surround
Down Sampling 48kHz
Digital Audio Out
Dolby Digital On
DTS Off
To select Dolby
Digital On or Off, press the ENTER button repeatedly.
DTS (Default : Off)
On : Output DTS sound
Set to On when the unit is connected to DTS
Decoder.
Language
Display
Audio
Audio Controls
Digital Audio Out ...
Dynamic Range On
Downmix Mode Dolby Surround
Down Sampling 48kHz
Digital Audio Out
Dolby Digital Off
DTS On
MPEG Off
To select DTS On or
Off, press the
ENTER button repeatedly.
MPEG (Default : Off)
On : Output by MPEG
Off : Convert the MPEG to PCM
Language
Display
Audio
Audio Controls
Digital Audio Out ...
Dynamic Range On
Downmix Mode Dolby Surround
Down Sampling 48kHz
Digital Audio Out
Dolby Digital Off
DTS Off
MPEG On
To select MPEG On or Off, press the
ENTER button repeatedly.
To select Downmix
Mode Stereo or
Dolby Surround, press the ENTER button repeatedly.
Set to On when the unit is connected to MPEG2
Decoder.
5
Press the SETUP button.
¡ The setup mode will be canceled and the ordinary screen will appear.
– 47 – EN
01A11
TD360_35-55 02.2.13 9:58 AM Page 48
PARENTAL LOCK
5
Press the RETURN button.
¡ The setup screen will appear.
1
Press the SETUP button.
¡ The setup screen will appear.
Language
Display
Audio
Parental
Select : / Set : ENTER
Cancel : Exit : SETUP
2
Press the
K / L
buttons to select Parental, and then press the ENTER button.
Display
Password
Enter current password...
Audio
_ _ _ _
Parental
Select : / Set : ENTER
Cancel : Exit :
SETUP
CONTROL LEVELS
¡Level 8
DVD software of any grade (adult/general/children) can be played back.
¡Levels 7 to 2
Only DVD software intended for general use and children can be played back.
¡Level 1
Only DVD software intended for children can be played back, with those intended for adult and general use prohibited.
3
Press the numeric buttons to enter the 4digit password, and then press the ENTER button.
¡ When doing this for the first time, enter any 4 digits.
That number will be used as the password from the second time onward.
¡ By entering the password, you can then change the control level and password settings.
Language
Parental Contorols
Parental Level 7[NC-17]
Change
Notes
¡
With some DVDs, it may be difficult to find if they are compatible with parental lock. Be sure to check if the parental lock function operates in the way that you have set.
¡ Record the password in case you forget it.
Display
4
Press the
K / L
buttons to select an item, and then press the ENTER button.
When Parental Level is selected
¡
Press the K / L buttons to select an item from 8 to 1 and then press the ENTER button.
¡ When Change is selected, press the numeric buttons to enter the four digits password. Then press the
ENTER button.
IF YOU FORGET THE PASSWORD
1) Open the tray.
2) Press the 1, 2, 3, 4, then DISPLAY button on the remote control. the default setup screen will appear.
Then, press the ENTER button.
3) Disconnect the power once and reconnect, then proceed the step 1 to 4 of the PARENTAL LOCK again.
Note: If you proceed the above steps, ALL the settings of the DVD player will be cleared. To use the DVD player under the previous settings, set each setting item all over again.
Language
Parental Contorols
Parental Level 7[NC-17]
Change
Display
Audio
Parental Level
5
4 [PG-13]
3 [PG]
2 o p
Language
Parental Contorols
Parental Level
Change
7[NC-17]
Display
Audio
Password
Enter current password
_ _ _ _
– 48 – EN
01A11
TD360_35-55 02.2.13 9:58 AM Page 49
LANGUAGE CODE LIST
No.
Language Country code
5
6
7
8
1
2
3
4
Afar
Abkhazian
4 7 4 7
4 7 4 8
Afrikaans 4 7 5 2
Amharic 4 7 5 9
Arabic
Assamese
Aymara
Azerbaijani
4 7 6 4
4 7 6 5
4 7 7 1
4 7 7 2
9 Bashkir
10 Byelorussian
11 Bulgarian
12 Bihari
13 Bislama
14 Bengali;Bangla
15 Tibetan
16 Breton
4 8 4 7
4 8 5 1
4 8 5 3
4 8 5 4
4 8 5 5
4 8 6 0
4 8 6 1
4 8 6 4
17 Catalan
18 Corsican
19 Czech
20 Welsh
21 Danish
22 German (GER)
23 Bhutani
24 Greek
25 English (ENG)
26 Esperanto
27 Spanish (SPA)
28 Estonian
29 Basque
30 Persian
31 Finnish
32 Fiji
4 9 4 7
4 9 6 1
4 9 6 5
4 9 7 1
5 0 4 7
5 0 5 1
5 0 7 2
5 1 5 8
5 1 6 0
5 1 6 1
5 1 6 5
5 1 6 6
5 1 6 7
5 2 4 7
5 2 5 5
5 2 5 6
33 Faroese
34 French (FRE)
35 Frisian
36 Irish
37 Scots Gaelic
38 Galician
39 Guarani
40 Gujarati
41 Hausa
42 Hindi
43 Croatian
44 Hungarian
45 Armenian
46 Interlingua
47 Interlingue
48 Inupiak
49 Indonesian
50 Icelandic
51 Italian (ITA)
52 Hebrew
53 Japanese (JPN)
54 Yiddish
55 Javanese
56 Georgian
57 Kazakh
58 Greenlandic
59 Cambodian
60 Kannada
61 Korean (KOR)
62 Kashmiri
63 Kurdish
64 Kirghiz
65 Latin
66 Lingala
67 Laothian
68 Lithuanian
5 5 6 0
5 5 6 5
5 5 6 6
5 5 6 9
5 6 4 7
5 6 5 5
5 6 6 9
5 7 4 7
5 7 5 7
5 7 5 8
5 7 5 9
5 7 6 0
5 7 6 1
5 7 6 5
5 7 6 7
5 7 7 1
5 8 4 7
5 8 6 0
5 8 6 1
5 8 6 6
5 2 6 1
5 2 6 4
5 2 7 1
5 3 4 7
5 3 5 0
5 3 5 8
5 3 6 0
5 3 6 7
5 4 4 7
5 4 5 5
5 4 6 4
5 4 6 7
5 4 7 1
5 5 4 7
5 5 5 1
5 5 5 7
No.
Language
69 Latvian;Lettish
70 Malagasy
71 Maori
72 Macedonian
73 Malayalam
74 Mongolian
75 Moldavian
76 Marathi
77 Malay
78 Maltese
79 Burmese
80 Nauru
81 Nepali
82 Dutch (DUT)
83 Norwegian
84 Occitan
85 (Afan)Oromo
86 Oriya
87 Panjabi
88 Polish
89 Pashto;Pushto
90 Portuguese
91 Quechua
92 Rhaeto-Romance
93 Kirundi
94 Romanian
95 Russian
96 Kinyarwanda
97 Sanskrit
98 Sindhi
99 Sangho
100 Serbo-Croatian
101 Singhalese
102 Slovak
103 Slovenian
104 Samoan
105 Shona
106 Somali
107 Albanian
108 Serbian
109 Siswat
110 Sesotho
111 Sundanese
112 Swedish
113 Swahili
114 Tamil
115 Telugu
116 Tajik
117 Thai
118 Tigrinya
119 Turkmen
120 Tagalog
121 Setswana
122 Tonga
123 Turkish
124 Tsonga
125 Tatar
126 Twi
127 Ukrainian
128 Urdu
129 Uzbek
130 Vietnamese
131 Volapuk
132 Wolof
133 Xhosa
134 Yoruba
135 Chinese (CHI)
136 Zulu
– 49 –
Country code
6 6 5 4
6 6 5 5
6 6 5 7
6 6 5 8
6 6 6 0
6 6 6 1
6 6 6 4
6 6 6 5
6 6 6 6
6 6 6 9
6 7 5 7
6 7 6 4
6 7 7 2
6 8 5 5
6 8 6 1
6 9 6 1
7 0 5 4
7 1 6 1
7 2 5 4
7 2 6 7
6 5 5 5
6 5 5 7
6 5 5 8
6 5 5 9
6 5 6 0
6 5 6 1
6 5 6 3
6 5 6 4
6 5 6 5
6 5 6 6
6 5 6 7
6 5 6 8
6 5 6 9
6 6 4 7
6 6 5 2
6 6 5 3
6 1 5 9
6 1 6 4
6 2 4 7
6 2 5 8
6 2 6 5
6 2 6 6
6 3 6 7
6 4 5 9
6 4 6 0
6 4 6 1
6 4 6 7
6 4 6 9
6 5 4 7
6 5 5 0
6 5 5 3
6 5 5 4
5 8 6 8
5 9 5 3
5 9 5 5
5 9 5 7
5 9 5 8
5 9 6 0
5 9 6 1
5 9 6 4
5 9 6 5
5 9 6 6
5 9 7 1
6 0 4 7
6 0 5 1
6 0 5 8
6 0 6 1
6 1 4 9
EN
01A11
TD360_35-55 02.2.13 9:58 AM Page 50
TROUBLESHOOTING GUIDE
TV/VCR
Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked possibilities. Before arranging for service, check these items. It could save your time and money.
No power.
PROBLEM
Remote Control Doesn’t Work
No picture and sound.
No picture or poor picture on
TV/DVD/VHS.
No sound or poor sound.
Bars On Screen
Picture Distorted or Blurred
Picture Rolls Vertically
Lines or Streaks in Picture
No Color
Poor Reception on Some Channels
Ghosts in Picture
Weak Picture
Sound OK, Picture Poor
Picture OK, Sound Poor
Timer recording is not possible.
Cannot go into Record mode.
CORRECTIVE ACTION
•
Make sure the AC cord is connected to an AC outlet.
•
Make sure the power is turned on.
•
Is TV/DVD plugged in?
•
Power at outlet?
•
Check batteries in Remote Control.
•
Make sure the AC cord is connected to an AC outlet.
•
Check antenna connection.
•
Let the TV/DVD/VHS program its tuner memory.
•
Adjust direction or replace antenna.
•
Adjust picture controls.
•
Adjust volume control on remote control or main unit.
•
Press the MUTE button to restore sound.
•
If outside antenna is being used, check for broken wire.
•
Check for local interference.
•
Try a new channel, if OK, then possible station trouble.
•
If outside antenna is being used, check for broken wire.
•
Try a new channel, if OK, then possible station trouble.
•
If outside antenna is being used, check for broken wire.
•
Check for local interference.
•
Try a new channel, if OK, then possible station trouble.
•
Is antenna connected to terminal on the back of the set?
•
If outside antenna is being used, check for broken wire.
•
Adjust COLOR control.
•
Try a new channel, if OK, then possible station trouble.
•
Is antenna connected to terminal on the back of the set?
•
If outside antenna is being used, check for broken wire.
•
Check for local interference.
•
Try a new channel, if OK, then possible station trouble.
•
Is antenna connected to terminal on the back of the set?
•
If outside antenna is being used, check for broken wire.
•
Adjust CONTRAST & BRIGHT control.
•
Try a new channel, if OK, then possible station trouble.
•
Is antenna connected to terminal on the back of the set?
•
If outside antenna is being used, check for broken wire.
•
Check for local interference.
•
Adjust CONTRAST & BRIGHT control.
•
Try a new channel, if OK, then possible station trouble.
•
Check for local interference.
•
Make sure the timer recording is set correctly.
•
Make sure the power is off.
•
Make sure the TV/DVD/VHS clock is set correctly.
•
Make sure the tape has an erase-prevention tab. If need, cover the
• hole with plastic tape.
– 50 – EN
01A11
TD360_35-55 02.2.13 9:59 AM Page 51
PROBLEM
Playback picture is partially noisy.
No picture but the audio is OK in playback.
No operation by infrared Remote
Control.
Video or color fades in and out when making a copy of a video tape.
Uneven color
CORRECTIVE ACTION
•
Adjust tracking control for a better picture using the CHANNEL K
• or
L button on the TV/DVD/VHS.
•
Head cleaning may be necessary. Refer to “AUTO HEAD
•
CLEANING” on page 53.
•
Make sure the AC cord is connected to an AC outlet.
•
Check batteries in remote control.
•
You can not copy a copyrighted video tape. You are experiencing
• copy guard protection.
•
Unplug the AC cord for about 30 minutes, then plug it again.
CLOSED CAPTION PROBLEM
My TV/DVD/VHS is showing captions that are misspelled.
POSSIBLE REMEDY
• You are watching a live broadcast and spelling errors made by the
• closed captioning production company may pass through uncorrected.
• A prerecorded program will not show any misspelled words because
• of the normal time available for editing the captions.
My TV/DVD/VHS will not show • Captions that are delayed a few seconds behind the actual the text dialogue are common for live broadcast. Most captioning production in its entirety or there is a delay of • companies can display a dialogue to a maximum of 220 words what is being said.
• per minute. If a dialogue exceeds that rate, selective editing is used
• to insure that the captions remain up-to-date with the current
• TV screen dialogue.
My captions are scrambled with white boxes on the TV screen.
• Interference caused by building, power lines, thunderstorms, etc.
• may cause scrambled or incomplete captions to appear.
My program guide listed a TV show • Broadcasters may at times use a time compression process to speed as being closed captioned but none • up the actual program so that additional advertising time can be of the captions were displayed.
• given. Since the decoder cannot read the compressed information,
• captions will be lost.
My prerecorded video tape does not • The video tape was either an illegal copy or the tape duplicating show any captions. The tape box • company accidentally left out the captioning signals during the mentions it being closed captioned.
• copying process.
My TV screen shows a black box • You are in the TEXT mode. Select CAPTION mode to CAPTION on certain channels.
• [OFF].
– 51 – EN
01A11
TD360_35-55 02.2.13 9:59 AM Page 52
DVD
If the TV/DVD does not perform properly when operated as instructed in this Owner’s Manual, check the player, consulting the following checklist.
Symptom
No power.
The player does not respond to the remote control.
No picture
Disc cannot be played
No sound
Distorted picture
Audio or subtitle language does not match the setup.
The camera angle cannot be changed.
Cause Remedy
•
Loose power plug.
•
Insert the power plug firmly into the wall out let.
•
The remote control is not aimed
•
Aim the remote control directly at the sensor
• at the sensor on the TV/DVD.
• on the TV/DVD.
•
Obstacles present between the
•
Remove the obstacles from the signal path.
• remote control and the sensor.
•
The remote control is too far
•
Use the remote control within 7m of
• away from the TV/DVD.
•
Dead batteries.
•
• the TV/DVD.
Replace the batteries.
•
•
Loose video connection.
Wrong disc.
•
Connect the video cables firmly.
•
Insert a correct video disc that plays on this
•
TV/DVD.
•
No disc.
•
Dirty disc.
•
Disc is placed upside down.
•
Place the disc correctly, with the label side up.
•
Parental lock is active.
•
•
Insert a disc.
•
Clean the disc.
Cancel the parental lock or change the control
• level.
•
Loose audio connection.
•
Connect the audio cables firmly.
•
The power of the connected
•
Turn the power of the audio component on.
• audio component is off.
•
Wrong audio output settings.
•
Correct the audio output settings.
•
Wrong input settings on the
•
Correct the input settings on the audio
• connected audio component.
• component.
•
•
Immediately after playing,
•
There are some cases where pictures may be
• press fast forward or in reverse.
• slightly distorted, which are not a sign of a
• malfunction.
•
The selected language is not
•
No malfunction.
• available for audio or subtitles
• on the DVD.
The DVD does not contain
• sequences recorded from
• different camera angles.
•
No malfunction.
•
The DVD does not contain
• audio source or subtitles in the
• selected language.
•
No malfunction.
•
That operation is prohibited by
•
No malfunction.
• the TV/DVD or disc.
Audio or subtitle language cannot be changed.
"Prohibited icon" appears on the screen, prohibiting an operation.
CD sound dropout
No CD reproduction
DVD picture dropout
DVD picture freeze
DVD picture in mosaic
No DVD reproduction
•
Scratched disc
•
Replace the disc with unscratched one.
NOTES:
•
Some functions are not available in specific modes, but this is not a malfunction. Read the description in this Owner’s Manual for details on correct operations.
•
Playback from a desired track and random playback are not available during program playback.
– 52 – EN
01A11
TD360_35-55 02.2.13 9:59 AM Page 53
MAINTENANCE
CABINET CLEANING
•
Wipe the front panel and other exterior surfaces of the TV/DVD with a soft cloth immersed in lukewarm water and wrung dry.
•
Never use a solvent or alcohol. Do not spray insecticide liquid near the TV/DVD. Such chemicals may cause damage and discoloration to the exposed surfaces.
1. Please visit your local Audio/Video store and purchase a good quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the problem, please call our help line at 1-800-968-3429, to locate an Authorized Service Center.
NOTES:
•
Remember to read the instructions included with the video head cleaner before use.
•
Clean video heads only when problems occur.
AUTO HEAD CLEANING
•
Automatically cleans video heads as you insert or remove a cassette, so you can see a clear picture.
•
Playback picture may become blurred of interrupted while the TV program reception is clear. Dirt accumulated on the video heads after long periods of use, or the usage of rental or worn tapes can cause this problem.
If a streaky or snowy picture appears during playback, the video heads in your TV/DVD/VHS may need to be cleaned.
SERVICING
•
Should your TV/DVD become inoperative, do not try to correct the problem by yourself. There are no user-serviceable parts inside. Turn off, unplug the power cord, and please call our help line at 1-800-
968-3429, to locate an Authorized Service Center.
IF THE LASER OPTICAL PICKUP UNIT IS DIRTY
•
If the player still does not perform properly when it is operated while referring to the relevant sections and to
"TROUBLESHOOTING GUIDE" in this Owner's Manual, the laser optical pickup unit may be dirty. Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.
DISC HANDLING
•
Use discs which have the following logos on them.
(Optical audio digital discs.)
•
Handle the discs so that fingerprints and dust do not adhere to the surfaces of the discs.
•
Always store the disc in its protective case when it is not used.
•
To clean-off, use a soft cloth.
•
Do not use a hard cloth since this will mar the disc.
•
Wipe the disc in a straight line from center to edge.
•
Never wipe with a circular motion.
•
Do not use detergent or abrasive cleaning agents.
– 53 –
TD360_35-55 02.2.13 9:59 AM Page 54
SPECIFICATIONS
GENERAL SPECIFICATIONS
TV/VCR
CRT : 19 inch in-line gun, 90˚ deflection tube
Television system : NTSC-M
Closed caption system :§15.119/FCC
Video Heads :
Tape width :
Tape speed
SP :
Rotary four-head
1/2 inch
LP :
SLP :
Tuner channel
TV VHF Low :
33.40mm/sec.
16.67mm/sec.
11.12mm/sec.
#2~#6
TV VHF High : #7~#13
TV UHF : #14~#69
CATV
VHF :
MID band :
SUPER band :
HYPER band :
5A
A5~A1, A~I
J~W
W+1~W+84
ELECTRICAL SPECIFICATIONS
Sound output: 2 speakers, 1W, 8 ohm
OTHER SPECIFICATIONS
Terminals
Antenna input: VHF/UHF/CATV
75 ohm unbalanced (F-type)
RCA connector
[
1 Video input:
Audio L/R input: RCA connector
[
2
Headphone: 1/8” stereo (3.5 mm)
Coaxial digital audio output: One pin jack,
500m Vpp (75 ohm)
Analog audio L/R output :
Remote control:
RCA connector
[
2
Digital encoded infrared light system
Operating temperature: 5ºC to 40ºC
(41ºF~104ºF)
Power requirements: AC 120V, 60Hz
Power consumption
(Maximum):
Picture tube:
Dimensions:
Weight:
Accessories:
85W
19"
H:19-21/32” (500mm)
W:23-13/16” (605mm)
D:18-11/16” (475mm)
48.5 lbs (22kg)
Remote Control Unit with
2"AA"batteries
Owner’s Manual
DVD
Product type: DVD Player
Discs: DVD video, Audio CD
Output signal format: NTSC color
Frequency response
(out put jack)
DVD (linear sound): 20 Hz to 22 kHz
(sample rate: 48 kHz)
20 Hz to 44 kHz
(sample rate: 96 kHz)
20 Hz to 20 kHz CD:
Signal-to-noise ratio
(S/N ratio)(out put jack)
CD: 100 dB (EIAJ)
Dynamic range
(out put jack)
DVD (linear sound): 85 dB
CD: 84 dB (EIAJ)
Total distortion factor
CD:
Wow and flutter:
0.07% (EIAJ)
Below the measurement limitation (+/-0.001%
W PEAK) (EIAJ)
•
Designs and specifications are subject to change without notice and without our legal obligation.
•
If there is a discrepancy between languages, the default language will be English.
– 54 – EN
01A11
TD360_35-55 02.2.13 9:59 AM Page 55
MEMO
– 55 – EN
01A11
TD360UAES 02.2.13 9:59 AM Page 56
INDICE
■ CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 56
PANEL FRONTAL DEL televisor/DVD/VHS . . . . . . . . . 56
MANDO A DISTANCIA . . . . . . . . . . . . . . . . . . . . . . . . . 56
VISTA POSTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 58
CONEXIONES DE ANTENA/TELEVISIÓN
POR CABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
INSTALACIÓN DE LAS PILAS. . . . . . . . . . . . . . . . . . . 58
CONEXIÓN A TOMAS DE ENTRADA EXTERNA. . . . 58
MODE DE ENTRADA EXTERNA . . . . . . . . . . . . . . . . . 58
CONEXIÓN A UN SISTEMA ESTÉREO (Para DVD) . . 58
CONEXIÓN A UN AMPLIFICADOR EQUIPADO CON
TOMAS DE ENTRADA DIGITAL, PLATINA MD O
PLATINA DAT (Para DVD) . . . . . . . . . . . . . . . . . . . . . . 58
CONEXIÓN A UN DECODIFICADOR DOLBY DIGITAL
O A UN DECODIFICADOR DTS (Para DVD) . . . . . . . . 59
TV SECTION
■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . . . 60
SELECCIÓN DE IDIOMA . . . . . . . . . . . . . . . . . . . . . . . 60
PREAJUSTE DE CANALES. . . . . . . . . . . . . . . . . . . . . . 60
DVD SECTION
■ REPRODUCCIÓN DE UN DISCO . . . . . . . . . . . . . . . . 61
REPRODUCCIÓN DE UN DVD DE VÍDEO O UN CD DE
AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
CONTROLES DE
OPERACIÓN Y FUNCIONES
PANEL FRONTAL DEL
TELEVISOR/DVD
Consulte la figura 1 de la página 9
MANDO A DISTANCIA
Consulte la figura 2 de la página 9
VISTA POSTERIOR
Consulte la figura 3 de la página 10
1.
Botón POWER
Púlselo para conectar y desconectar la alimentación.
2.
Botones VOLUME
K
/
L
Púlselos para controlar el nivel del volumen para el DVD y el televisor.
3.
Botones SKIP (para DVD)
Salta capítulos o pistas hasta un punto deseado.
4.
Botón PLAY
Inicia la reproducción del contenido del disco o la cinta.
5.
Botón STOP
Detiene la operación del disco o la cinta.
6.
Botón OPEN/CLOSE
Púlselo para insertar discos en la bandeja o retirarlos de ella.
7.
Bandeja de carga del disco
8.
Indicador de DVD
Parpadea durante el modo del DVD.
9.
Botón SELECT
Púlselo para cambiar a un modo de televisor, modo de entrada externa o modo de DVD.
10.
Indicador del televisor/ la videograbadora
(TV/VCR)
Parpadea durante el modo del televisor/ la videograbadora
11.
Botones CHANNEL
K
/
L
Púlselo para seleccionar el canal memorizado.
Púlselo para cambiar a un modo de televisor cuando modo de DVD.
12.
Indicador de grabación (RECORD)
Parpadea durante la grabación.
Se enciende en el modo de espera de la grabación con temporizador.
Botón de grabación de un toque (OTR)
Activa la grabación de un toque. (Sólo en el televisor/DVD/VHS)
13.
Botón de grabación (REC)
Púlselo para iniciar la grabación manual.
14.
Botón de rebobinado (REW) (para televisor/ videograbadora)
Púlselo para rebobinar la cinta, o para ver la imagen en retroceso rápido durante el modo de reproducción.
(Búsqueda con rebobinado)
15.
Botón de avance rápido (FWD) (para televisor/ videograbadora)
Púlselo para avanzar rápidamente la cinta, o para ver la imagen en avance rápido durante el modo de reproducción. (Búsqueda con avance rápido)
16.
Botón de parada (STOP)
Púlselo para detener la cinta.
Botón de expulsión (EJECT)
Púlselo en el modo de parada para expulsar la cinta del televisor/videograbadora.
17.
Ventanilla del sensor del mando a distancia
18.
Toma HEADPHONE
Para conectar auriculares (no suministrados) y escuchar en privado.
19.
Toma de entrada VIDEO
Conecte aquí la toma de salida de vídeo de una videocámara o de una videograbadora.
20.
Tomas de entrada AUDIO L/R
Conecte aquí las tomas de salida de audio de una videocámara o de una videograbadora.
21.
Compartimiento del videocasete
22.
Botón PICTURE
Presione para entrar en el modo de ajuste de imagen.
– 56 – ES
1D18
TD360UAES 02.2.13 9:59 AM Page 57
23.
Botones de números
Modo del televisor:
Pulse dos dígitos para tener acceso directamente al canal deseado.
Recuerde pulsar "0" antes de elegir un canal de un solo dígito.
Botón +100
Púlselo para seleccionar canales de televisión por cable cuyo número sea igual o superior al 100.
Modo DVD:
Púlselo para introducir el número deseado.
Botón +10
Púlselo para introducir los números deseados cuyo número sea igual o superior al 10.
24.
Botón PAUSE
Hace una pausa en la operación del disco o la cinta.
25.
Botón de velocidad de cinta (SPEED)
Púlselo para elegir la velocidad de grabación deseada:
SP/SLP.
26.
Botón C-RESET
Púlselo para reponer el contador a 0:00:00.
27.
Botón DISPLAY
Modo del televisor/ la videograbadora:
Púlselo para visualizar el número del canal en la pantalla. Si lo pulsa de nuevo, el número del canal desaparecerá.
Modo de DVD:
Visualiza el estado actual en la pantalla del televisor con fines de comprobación.
28.
Botón SETUP
Púlselo para activar o salir del modo de menús de televisor o preparación de DVD.
29.
Botón TITLE
Visualiza el menú de títulos.
30.
Botón CLEAR
Repone un ajuste.
31.
Botón MODE
Activa el modo de reproducción programada o el modo de reproducción aleatoria.
32.
Botón SEARCH MODE
Púlselo para localizar un punto deseado.
33.
Botón AUDIO
Púlselo para seleccionar un idioma de audio o un modo de sonido deseado.
34.
Botón SUBTITLE
Púlselo para seleccionar un idioma de subtítulos deseado.
35.
Botón REPEAT
Repite la reproducción del disco, título, capítulo o pista actual.
36.
Botón ANGLE
Púlselo para cambiar el ángulo de la cámara y verde, desde un ángulo diferente, la secuencia que está siendo reproducida.
37.
Botón A-B REPEAT
Repite la reproducción de una sección seleccionada.
38.
Botón RETURN
Para volver a la operación anterior.
39.
Botón ENTER
Púlselo para establecer un ajuste.
40.
Botones de flechas
Modo de televisor:
Púlselo para seleccionar un modo de ajuste desde el menú que aparece en la pantalla del televisor.
Púlselo para seleccionar o ajustar desde un menú particular.
Modo de DVD:
Se utiliza cuando se hacen ajustes mientras se observa la visualización en una pantalla de televisor.
41.
Botón DISC MENU
Visualiza menús de DVD.
42.
Botón ZOOM
Amplia parte de una imagen de DVD reproducida.
43.
Botón MUTE
Pulse el botón MUTE para apagar el sonido de un programa de TV. La visualización del nivel del sonido cambia de ROJO CLARO a AZUL
CLARO.) Pulse de nuevo el botón MUTE o el botón VOL K o L para restaurar el sonido.
44.
Botón DVD
Púlselo para cambiar a un modo de DVD.
45.
Botón TV/VCR
Púlselo para cambiar a un modo de televisor/ videograbadora.
46.
Toma de entrada ANT.
Conéctela a una antena, sistema de televisión por cable o sistema de satélite.
47.
Cable de alimentación
Conéctelo a una toma de CA convencional (120
V/60 Hz).
NOTA:
Retire el cable de alimentación del gancho para evitar romperlo antes de conectarlo a una toma de CA convencional.
48.
Toma de salida de audio digital COAXIAL
Conéctela a la entrada digital de un amplificador o decodificador externo.
49.
Toma de salida AUDIO L/R
Conéctela a la entrada de audio analógico de un amplificador o decodificador externo.
NOTA
:
Las tomas de entrada de audio (roha y blanca) en el lado trasero sirven para producir no el son televisor ni el son de entrada externa, sino el son DVD.
– 57 – ES
1D18
TD360UAES 02.2.13 9:59 AM Page 58
PREPARACIÓN PARA LA
UTILIZACIÓN
fuente a las tomas AUDIO L/R y VIDEO de este televisor/DVD/VHS. Y luego pulse el botón SELECT hasta que "VIDEO" aparezca en la pantalla.
CONEXIONES DE ANTENA/
TELEVISIÓN POR CABLE
Consulte la figura 4 de la página 11
NOTA:
•
Cuando conecte una videograbadora monoaural
(otra fuente) a este televisor/DVD/VHS, conecte la toma de salida de audio de la videograbadora monoaural (otra fuente) a la toma AUDIO L de este televisor/DVD/VHS. El audio saldrá igualmente en los canales L y R.
ANTENAS SEPARADAS DE VHF/UHF
En algunas áreas será necesario utilizar una antena exterior.
Consulte la figura 5 de la página 12
Consulte la figura 4 de la página 11
Conexiones de antena/televisión por cable
Continúa en la página siguiente.
TELEVISIÓN POR CABLE SIN CAJA DE
CONVERTIDOR/DECODIFICADOR
Utilice esta conexión si su sistema de televisión por cable se conecta directamente a su televisor/DVD/VHS sin necesidad de caja de convertidor.
Consulte la figura 4 de la página 11
TELEVISIÓN POR CABLE CON CAJA
DE CONVERTIDOR/DECODIFICADOR
O CAJA DE SATÉLITE
Si su proveedor de servicios de televisión por cable le suministra una caja de convertidor o si usted utiliza un sistema de satélite, podrá utilizar la conexión básica mostrada aquí.
Consulte la figura 4 de la página 11
INSTALACIÓN DE LAS PILAS
1) Abra la tapa del compartimiento de las pilas del mando a distancia presionándola en el sentido de la flecha.
2) Inserte 2 pilas tamaño "AA" en su compartimiento colocando las polaridades (+/-) en sus posiciones correspondientes.
3) Vuelva a poner la tapa.
CONEXIÓN A TOMAS DE
ENTRADA EXTERNA
Cuando vea un programa grabado en otra fuente
(videograbadora o videocámara), utilice las tomas de entrada de audio/vídeo de la parte delantera del televisor/DVD/VHS.
Conecte las tomas de salida de audio/vídeo de otra
MODO DE ENTRADA EXTERNA
Cuando utilice una señal de entrada externa (otra videograbadora o una videocámara), conecte los cables de salida de audio/vídeo del equipo de reproducción a las tomas AUDIO IN/VIDEO IN de su televisor/videograbadora. Y luego pulse el botón
CHANNEL K o L hasta que “AUX” aparezca en la pantalla.
Usted puede programar el temporizador para que explore todos los canales que puedan recibirse en su zona.
CONEXIÓN A UN SISTEMA
ESTÉREO (Para DVD)
Consulte la figura 6 de la página 14
NOTAS:
•
Asegúrese de desconectar la alimentación a todos los componentes del sistema antes de hacer la conexión a otro componente.
•
Consulte el manual del propietario de su sistema estéreo y de cualquier otro componente que vaya a conectar al televisor/DVD/VHS.
•
Las tomas de entrada de audio (roha y blanca) en el lado trasero sirven para producir no el son televisor ni el son de entrada externa, sino el son DVD.
CONEXIÓN A UN
AMPLIFICADOR EQUIPADO
CON TOMAS DE ENTRADA
DIGITAL, PLATINA MD O
PLATINA DAT (Para DVD)
Utilice un cable digital coaxial (de venta en el comercio) para las conexiones de audio.
Consulte la figura 7 de la página 14
– 58 – ES
1D18
TD360UAES 02.2.13 9:59 AM Page 59
NOTAS:
•
La fuente de audio de un disco del formato de sonido ambiental Dolby Digital de 5,1 canales no puede ser grabada como sonido digital por una platina MD o DAT.
•
Asegúrese de desconectar la alimentación de todos los componentes del sistema antes de hacer la conexión a otro componente.
•
Consulte los manuales del propietario de los componentes que vaya a conectar al televisor/DVD/VHS.
•
Ponga DOLBY DIGITAL y DTS en OFF para la salida de audio en el modo de preparación. La reproducción en el televisor/DVD/VHS utilizando los ajustes incorrectos puede generar distorsión de ruido, y también puede estropear los altavoces.
•
El audio se silenciará cuando DOLBY DIGITAL se ponga en OFF y VIRTUAL 3D se ponga en ON para la salida de audio en el modo de preparación y usted seleccione la fuente de audio del formato de sonido ambiental Dolby Digital de 5,1 canales.
•
A menos que se haga la conexión a un decodificador Dolby Digital o DTS, ponga DOLBY DIGI-
TAL y DTS en OFF para la salida de audio en el modo de preparación. La reproducción en el televisor/DVD/VHS utilizando los ajustes incorrectos puede generar distorsión de ruido, y también puede estropear los altavoces.
•
El audio se silenciará cuando DOLBY DIGITAL se ponga en OFF y VIRTUAL 3D se ponga en ON para la salida de audio en el modo de preparación y usted seleccione la fuente de audio del formato de sonido ambiental Dolby Digital de 5,1 canales.
Fabricado bajo licencia de Dolby
Laboratories. “Dolby” y el símbolo de la D doble son marcas de fábrica de Dolby
Laboratories.
CONEXIÓN A UN
DECODIFICADOR DOLBY
DIGITAL O A UN
DECODIFICADOR DTS
(Para DVD)
Si se utiliza este televisor/DVD/VHS para reproducir fuentes del formato de sonido ambiental Dolby
Digital de 5,1 canales o de sonido ambiental DTS, el televisor/DVD/VHS dará salida a un flujo de datos
Dolby Digital o DTS desde su toma de salida de audio digital COAXIAL. Conectando el reproductor a un decodificador Dolby Digital o DTS, usted podrá disfrutar de un ambiente más convincente y real con un sonido ambiental potente y de alta calidad de tipo profesional tal como el que se oye en salas de cine.
Utilice cables digitales coaxiales (de venta en el comercio) para las conexiones de audio.
Consulte la figura 8 de la página 13
NOTAS:
•
Asegúrese de desconectar la alimentación de todos los componentes del sistema antes de hacer la conexión a otro componente.
•
Consulte los manuales del propietario de los componentes que vaya a conectar al televisor/DVD/VHS.
•
Si conecta un decodificador Dolby Digital, ponga
DOLBY DIGITAL en ON para la salida de audio en el modo de preparación.
•
Si conecta un decodificador DTS, ponga DTS en
ON para la salida de audio en el modo de preparación.
– 59 –
“DTS” y “DTS Digital Out” son marcas de fábrica de Digital Theater Systems, Inc.
ES
1D18
TD360UAES 02.2.13 9:59 AM Page 60
TV SECTION
PREPARACIÓN PARA LA
UTILIZACIÓN
AJUSTE DEL RELOJ
Cerciórese...
• La alimentación del televisor/videograbadora deberá estar conectada.
En el ejemplo de abajo, el reloj va a ajustarse así:
FECHA: 7 de mayo de 2002
HORA: 5:40 PM
PREPARACIÓN DE CANALES
POR PRIMERA VEZ
1
Conecte el cable de alimentación a una toma de CA convencional.
NOTA: Si aparecen algunos dígitos en la esquina de la pantalla, pulse el botón POWER sin desenchufar el cable de alimentación.
1
Pulse el botón SETUP en el mando a distancia.
Pulse el botón PLAY/K o STOP/L para indicar
“AJUSTE RELOJ”. Luego, pulse el botón F.FWD/B.
2
Pulse el botón POWER para encender el televisor/DVD/VHS.
3
Seleccione "ESPAÑOL" o "ENGLISH" (inglés),
"FRANÇAIS" (francés) utilizando el botón de flecha
B o s.
4
Pulse el botón flecha K o L para señalar “AUTOP-
RESELECCION”.
Luego pulse el botón flecha B. El sintonizador explorará y memorizará todos los canales activos de su área.
NOTAS:
• El televisor/videograbadora distingue entre los canales de televisión estándar y los canales de televisor por cable.
• Si desea reproducir o grabar una cinta ANTES de preajustar el sintonizador, usted tendrá que pulsar el botón SETUP en el mando a distancia. Para preajustar de nuevo el sintonizador, consulte
“REPETICIÓN DE LA PREPARACIÓN DE
CANALES”.
• La unidad de televisor/videograbadora puede reconocer los canales de TV como ellos de TV por cable a causa de los condiciones de recepción. En este caso, pruebe el preajuste automático de nuevo en los condiciones finas de recepción.
2
Pulse el botón PLAY/K o STOP/L para indicar
“AJUSTE MANUAL RELOJ”. Luego, pulse el botón
F.FWD/B.
3
Pulse el botón PLAY/K o STOP/L hasta que aparezca el mes deseado. (Ejemplo: Mayo - 05) Luego, pulse el botón F.FWD/B.
4
Pulse el botón PLAY/K o STOP/L hasta que aparezca el día del mes deseado. (Ejemplo: 7 - 07) Luego, pulse el botón F.FWD/B.
5
Pulse el botón PLAY/K o STOP/L hasta que aparezca el año deseado. (Ejemplo: 2002) Luego, pulse el botón F.FWD/B.
6
Pulse el botón PLAY/K o STOP/L hasta que aparezca la hora deseada. (Ejemplo: 5, PM) Luego, pulse el botón F.FWD/B.
7
Pulse el botón PLAY/K o STOP/L hasta que aparezca el minuto deseado. (Ejemplo: 40)
5
El sintonizador se para en el canal memorizado más bajo. Si desea recuperar canales seleccionados, usted podrá seleccionar directamente el canal deseado con los botones numerados del mando a distancia o con los botones CHANNEL K o L.
– 60 –
8
Pulse el botón SRTUP en el mando a distancia.
Aunque los segundos no se visualizan, éstos empiezan a contar desde 00 cuando se pulsa SETUP en el mando a distancia. Utilice esta función para sincronizar el reloj con la hora correcta.
ES
1D18
TD360UAES 02.2.13 9:59 AM Page 61
DVD SECTION
REPRODUCCIÓN DE UN
DISCO
REPRODUCCIÓN DE UN DVD
DE VÍDEO O UN CD DE AUDIO
DVD CD
Para empezar
Conecte la alimentación del televisor, amplificador y cualquier otro componente que esté conectado al reproductor DVD. (Cambie el sistema de entrada para adaptarlo al reproductor DVD, y compruebe que el volumen del sonido sea correcto.)
1
Pulse el botón POWER.
¡
La alimentación se conectará.
2
Pulse el botón OPEN/CLOSE.
¡ La bandeja de carga del disco se abrirá.
3
Ponga un disco en la bandeja.
¡ Asegúrese de que el disco esté correctamente asentado en el hueco correcto, con el lado de la etiqueta hacia arriba.
4
Pulse el botón PLAY.
¡ La bandeja se cerrará automáticamente y la reproducción empezará desde el primer capítulo o pista del disco. Necesitará pulsar el botón PLAY sólo cuando la bandeja haya sido cerrada pulsando el botón OPEN/CLOSE.
¡
Cuando reproduzca un DVD que tenga grabado un menú de títulos, el menú tal vez aparezca en la pantalla. En este caso, consulte "UTILIZACIÓN DEL
MENÚ DE TÍTULOS".
5
Pulse el botón STOP para detener la reproducción.
– 61 – ES
1D18
TD360UAES 02.2.13 9:59 AM Page 62
MEMO
– 62 – ES
1D18
TD360UAES 02.2.13 9:59 AM Page 63
MEMO
– 63 – ES
1D18
TD360_35-55 02.2.13 9:59 AM Page 64
LIMITED WARRANTY
FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or workmanship as follows:
DURATION:
PARTS:
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this warranty.
LABOR:
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of original retail purchase.
LIMITS AND EXCLUSIONS:
This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail purchase will be required together with the product to obtain service under this warranty.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to any product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this product or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS
REPRESENTATIVES IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED
SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI
AUTHORIZED SERVICE FACILITY.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS
THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI
CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
To locate your nearest SYLVANIA Authorized Service Center or for general service procedure, please call 1-800-968-3429 or write to the following:
FUNAI CORPORATION, INC.
Customer Service
100 North Street; Teterboro, NJ 07608
Tel :1-800-968-3429
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
Printed in Malaysia 0EMN01945
TD360UA
★★★★★
advertisement
Related manuals
advertisement
Table of contents
- 56 PANEL FRONTAL DEL televisor/DVD/VHS
- 56 MANDO A DISTANCIA
- 56 VISTA POSTERIOR
- 58 POR CABLE
- 58 INSTALACIÓN DE LAS PILAS
- 58 CONEXIÓN A TOMAS DE ENTRADA EXTERNA
- 58 MODE DE ENTRADA EXTERNA
- 58 CONEXIÓN A UN SISTEMA ESTÉREO (Para DVD)
- 58 PLATINA DAT (Para DVD)
- 59 O A UN DECODIFICADOR DTS (Para DVD)
- 60 SELECCIÓN DE IDIOMA
- 60 PREAJUSTE DE CANALES
- 61 AUDIO