advertisement
Monitor
User Manual
S32E590C
The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance.
Table of contents
Before Using the Product
Securing the Installation Space
Correct posture to use the product 12
Preparations
Wall Mount Kit Specifications (VESA) 24
Connecting and Using a Source
Device
Connection Using the HDMI Cable
Connection Using an HDMI-DVI Cable
Connecting to Headphones or Speakers
Screen Setup
Configuring SAMSUNG MAGIC Bright
Configuring the HDMI Black Level Settings 35
Configuring the Response Time 38
Configuring H-Position & V-Position 41
Coordinating OSD
2
Table of contents
Setup and Reset
Configuring Eco Saving Plus 48
Configuring DisplayPort Ver. 52
Configuring Source Detection 53
Configuring Key Repeat Time 54
Initializing Settings (Reset All) 56
Information Menu and Others
Configuring Brightness, Contrast and Sharpness from the Initial Screen 58
Configuring Volume in the Initial Screen 59
Installing the Software
Troubleshooting Guide
Requirements Before Contacting Samsung
Checking the Resolution and Frequency
Specifications
Appendix
Responsibility for the Pay Service
A Product damage caused by customer's fault 72
Correct Disposal of This Product (Waste Electrical &
3
Chapter 01
Before Using the Product
Copyright
The contents of this manual are subject to change without notice to improve quality.
ⓒ 2015 Samsung Electronics
Samsung Electronics owns the copyright for this manual.
Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited.
Microsoft, Windows are registered trademarks of Microsoft Corporation.
VESA, DPM and DDC are registered trademarks of the Video Electronics Standards Association.
Ownership of all other trademarks is attributed to their due owner.
4
Securing the Installation Space
Ensure some space around the product for ventilation. An internal temperature rise may cause fire and damage the product. Be sure to allow the amount of space as shown below or greater when installing the product.
― The exterior may differ depending on the product.
10 cm
10 cm
Safety Precautions
Caution
RISK OF ELECTRIC SHOCK DO NOT OPEN
Caution : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. (OR BACK)
THERE ARE NO USER SERVICEABLE PARTS INSIDE.
REFER ALL SERVICING TO QUALIFIED PERSONNEL.
10 cm 10 cm
This symbol indicates that high voltage is present inside.
It is dangerous to make any kind of contact with any internal part of this product.
10 cm
Precautions for storage
High-glossy models can develop white stains on the surface if an ultrasonic wave humidifier is used nearby.
― Contact your nearest Samsung Customer Service Center if you want to clean the inside of the product
(Service fee will be charged.)
This symbol alerts you that important literature concerning operation and maintenance has been included with this product.
Symbols
Warning
A serious or fatal injury may result if instructions are not followed.
Caution
Personal injury or damage to properties may result if instructions are not followed.
Activities marked by this symbol are prohibited.
Instructions marked by this symbol must be followed.
5
Cleaning
― Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched.
― Take the following steps when cleaning.
― The following images are for reference only. Real-life situations may differ from what is shown in the images.
1 Power off the product and computer.
2 Disconnect the power cord from the product.
― Hold the power cable by the plug and do not touch the cable with wet hands. Otherwise, an electric shock may result.
3
Wipe the monitor with a clean, soft and dry cloth.
• Do not apply a cleaning agent that contains alcohol, solvent, or surfactant to the monitor.
!
• Do not spray water or detergent directly on the product.
4
Wet a soft and dry cloth in water and wring thoroughly to clean the exterior of the product.
Electricity and Safety
― The following images are for reference only. Real-life situations may differ from what is shown in the images.
Warning
Do not use a damaged power cord or plug, or a loose power socket.
• An electric shock or fire may result.
Do not use multiple products with a single power socket.
• Overheated power sockets may cause a fire.
Do not touch the power plug with wet hands. Otherwise, an electric shock may result.
Insert the power plug all the way in so it is not loose.
• An unsecure connection may cause a fire.
!
5
Connect the power cord to the product when cleaning is finished.
6
Power on the product and computer.
!
Connect the power plug to a grounded power socket (type 1 insulated devices only).
• An electric shock or injury may result.
6
!
!
!
Caution
Do not bend or pull the power cord with force. Be careful not to leave the power cord under a heavy object.
• Damage to the cord may result in a fire or electric shock.
Do not place the power cord or product near heat sources.
• A fire or electric shock may result.
Clean any dust around the pins of the power plug or the power socket with a dry cloth.
• A fire may result.
!
Installation
Warning
Hold the plug when disconnecting the power cord from the power socket.
• An electric shock or fire may result.
DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP OF
THE PRODUCT. DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES.
• A fire may result.
Do not disconnect the power cord while the product is being used.
• The product may become damaged by an electric shock.
Do not install the product in poorly ventilated spaces such as a bookcase or closet.
• An increased internal temperature may cause a fire.
Install the product at least 10 cm away from the wall to allow ventilation.
• An increased internal temperature may cause a fire.
Only use the power cord provided with your product by Samsung. Do not use the power cord with other products.
• A fire or electric shock may result.
Keep the power socket where the power cord is connected unobstructed.
• The power cord must be disconnected to cut off power to the product when an issue occurs.
!
!
Keep the plastic packaging out of the reach of children.
• Children may suffocate.
7
!
Do not install the product on an unstable or vibrating surface (insecure shelf, sloped surface, etc.)
• The product may fall and become damaged and/or cause an injury.
• Using the product in an area with excess vibration may damage the product or cause a fire.
Do not install the product in a vehicle or a place exposed to dust, moisture
(water drips, etc.), oil, or smoke.
• A fire or electric shock may result.
Caution
!
Do not expose the product to direct sunlight, heat, or a hot object such as a stove.
• The product lifespan may be reduced or a fire may result.
Do not install the product within the reach of young children.
• The product may fall and injure children.
Do not drop the product while moving.
• Product failure or personal injury may result.
Do not set down the product on its front.
• The screen may become damaged.
When installing the product on a cabinet or shelf, make sure that the bottom edge of the front of the product is not protruding.
• The product may fall and become damaged and/or cause an injury.
• Install the product only on cabinets or shelves of the right size.
Set down the product gently.
• Product failure or personal injury may result.
Edible oil, such as soybean oil, can damage or deform the product. Do not install the product in a kitchen or near a kitchen counter.
!
!
SAMSUNG
Installing the product in an unusual place (a place exposed to a lot of fine dust, chemical substances, extreme temperatures or a significant presence of moisture, or a place where the product will operate continuously for an extended period of time) may seriously affect its performance.
• Be sure to consult Samsung Customer Service Center if you want to install the product at such a place.
8
Operation
Warning
!
!
There is a high voltage inside the product. Never disassemble, repair or modify the product yourself.
• A fire or electric shock may result.
• Contact Samsung Customer Service Center for repairs.
To move the product, first disconnect all the cables from it, including the power cable.
• Damage to the cord may result in a fire or electric shock.
If the product generates abnormal sounds, a burning smell or smoke, disconnect the power cord immediately and contact Samsung Customer
Service Center.
• An electric shock or fire may result.
Do not let children hang from the product or climb on top of it.
• Children may become injured or seriously harmed.
!
!
!
If the product is dropped or the outer case is damaged, turn off the power switch and disconnect the power cord. Then contact Samsung Customer
Service Center.
• Continued use can result in a fire or electric shock.
Do not leave heavy objects or items that children like (toys, sweets, etc.) on top of the product.
• The product or heavy objects may fall as children try to reach for the toys or sweets resulting in a serious injury.
During a lightning or thunderstorm, power off the product and remove the power cable.
• A fire or electric shock may result.
Do not drop objects on the product or apply impact.
• A fire or electric shock may result.
GAS
Do not move the product by pulling the power cord or any cable.
• Product failure, an electric shock or fire may result from a damaged cable.
If a gas leakage is found, do not touch the product or power plug. Also, ventilate the area immediately.
• Sparks can cause an explosion or fire.
Do not lift or move the product by pulling the power cord or any cable.
• Product failure, an electric shock or fire may result from a damaged cable.
9
!
100
Do not use or keep combustible spray or an inflammable substance near the product.
• An explosion or fire may result.
Caution
Ensure the vents are not blocked by tablecloths or curtains.
• An increased internal temperature may cause a fire.
Do not insert metallic objects (chopsticks, coins, hairpins, etc) or objects that burn easily (paper, matches, etc) into the product (via the vent or input/ output ports, etc).
• Be sure to power off the product and disconnect the power cord when water or other foreign substances have entered the product.
Then contact Samsung Customer Service Center.
• Product failure, an electric shock or fire may result.
Do not place objects containing liquid (vases, pots, bottles, etc) or metallic objects on top of the product.
• Be sure to power off the product and disconnect the power cord when water or other foreign substances have entered the product.
Then contact Samsung Customer Service Center.
• Product failure, an electric shock or fire may result.
!
!
!
-_-
Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage burn-in or defective pixels.
• Activate power-saving mode or a moving-picture screen saver if you will not be using the product for an extended period of time.
Disconnect the power cord from the power socket if you do not plan on using the product for an extended period of time (vacation, etc).
• Dust accumulation combined with heat can cause a fire, electric shock or electric leakage.
Use the product at the recommended resolution and frequency.
• Your eyesight may deteriorate.
Do not put DC power adapters together.
• Otherwise, a fire may result.
Remove the plastic bag from the DC power adapter before you use it.
• Otherwise, a fire may result.
Do not let water enter the DC power device or get the device wet.
• An electric shock or fire may result.
• Avoid using the product outdoors where it can be exposed to rain or snow.
• Be careful not to get the DC power adapter wet when you wash the floor.
10
!
!
!
Do not put the DC power adapter near to any heating apparatus.
• Otherwise, a fire may result.
Keep the DC power adapter in a well-ventilated area.
Do not hold the product upside-down or move it by holding the stand.
• The product may fall and become damaged or cause an injury.
Looking at the screen too close for an extended period of time can deteriorate your eyesight.
!
!
Do not use humidifiers or stoves around the product.
• A fire or electric shock may result.
Rest your eyes for more than 5 minutes for every 1 hour of product use.
• Eye fatigue will be relieved.
Do not touch the screen when the product has been turned on for an extended period of time as it will become hot.
Store small accessories out of the reach of children.
Exercise caution when adjusting the product angle or stand height.
• Your hand or finger may get stuck and injured.
• Tilting the product at an excessive angle may cause the product to fall and an injury may result.
Do not place heavy objects on the product.
• Product failure or personal injury may result.
When using headphones or earphones, do not turn the volume too high.
• Having the sound too loud may damage your hearing.
11
Correct posture to use the product
Use the product in the correct posture as follows:
• Straighten your back.
• Allow a distance of 45 to 50cm between your eye and the screen, and look slightly downward at the screen. Keep your eyes directly in front of the screen.
• Adjust the angle so light does not reflect on the screen.
• Keep your forearms perpendicular to your upper arms and level with the back of your hands.
• Keep your elbows at about a right angle.
• Adjust the height of the product so you can keep your knees bent at 90 degrees or more, your heels attached to the floor, and your arms lower than your heart.
12
Chapter 02
Preparations
Contact the vendor where you purchased the product if any components are missing.
The appearance of the components may differ from the images shown.
The optimal resolution may not be available when using a non-high speed
HDMI or HDMI-DVI cable.
Checking the Components
Components
― Components may vary depending on the country.
Quick Setup Guide
Warranty card
(Not available in some locations)
Regulatory guide
DC power adapter (Detachable)
(
)
HDMI cable (Optional) (
) Stand base
HOLDER-SCREW (4EA) (Optional)
Power cable (
)
Stand neck
13
Parts
Control Panel
― The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.
JOG Button
UP
LEFT RIGHT
2
Function Key Guide
PRESS(ENTER) DOWN
Icons
JOG Button
Function Key Guide
Description
Multi directional button that helps navigate.
― The JOG button is located on the rear left side of the product. The button can be used to move up, down, left or right, or as Enter.
Press the JOG button when the screen is turned on. The Function Key Guide will appear. To access the onscreen menu when the guide is displayed, press the corresponding direction button again.
― Function Key Guide may vary depending on the function or product model. Please refer to the actual product.
Return
14
Direct Key guide
Brightness
Volume
Features
Eye Saver Mode Off
― The shortcut button screen (OSD menu) shown below is displayed only when the monitor screen is turned on, the computer resolution changes, or the input source changes.
• UP/DOWN: Adjust Brightness , Contrast , Sharpness .
• LEFT/RIGHT: Adjust Volume , Mute .
• PRESS(ENTER): Display Function Key Guide.
― The function buttons page shows if Eye Saver Mode is enabled.
: On
: Off
15
Function Key Guide
― To enter the main menu or to use other items, press the JOG button to display the Function Key Guide. You can exit by pressing the JOG button again.
Return
UP/DOWN/LEFT/RIGHT: Move to the item you want. The description for each item will appear when the focus changes.
PRESS(ENTER): The selected item will be applied.
Icons Description
Selects to change the input signal by moving the JOG button in the Function Key
Guide screen. A message will appear on the top left corner of the screen if the input signal has been changed.
Selects by moving the JOG button in the function key guide screen.
The OSD (On Screen Display) of your Monitor’s feature appears.
OSD control lock: Maintain the current settings, or lock the OSD control to prevent unintended changes to settings. Enable/Disable: To lock/unlock the OSD control, press the
LEFT button for 10 seconds when the main menu displayed.
If the OSD control is locked, Brightness and Contrast can be adjusted.
Eye Saver Mode is available. System Power LED On is available. Information can be viewed.
Selects by moving the JOG button in the function key guide screen.
Press to enable or disable Eye Saver Mode .
The items below are not available if the Eye Saver Mode function is enable.
• Picture Game Mode ,
• System Eco Saving Plus
Bright , Brightness , Color
Selects to turn the Monitor off by moving the JOG button in the function key guide screen.
― Actual models because of functional variation, Function key guide options will be different. Please run the corresponding function based on the actual icon and description.
16
― When the monitor displays nothing (i.e. Power saving mode or Non-signal mode), 2 direct keys for control source and power could be used as below.
JOG Button
UP
Power saving/Non-signal mode
Source Change
Down
PRESS(ENTER) for 2 seconds Power Off
― When the monitor displays the Main menu the JOG Button could be used as below.
JOG Button
UP/DOWN
Action
Move the option
LEFT
Exit the Main menu.
Close Sublist without saving value.
Value decreases in the slider.
RIGHT
PRESS(ENTER)
Move to next depth.
Value increases in the slider.
Move to next depth.
Save the value and close Sublist.
17
Reverse Side
― The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.
Port
2
Description
Connects to a PC using a DP cable.
Connects to a source device using an HDMI cable or HDMI-DVI cable.
Connect to an audio output device such as headphones.
Connects to the DC power adapter.
18
Installation
Attaching the Stand
― Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards.
: The product is curved. Placing pressure on the product when on a flat surface may damage the product. When the product is on the ground facing up or down, do not put pressure on it.
1 Insert the stand neck into the stand base in the direction shown in the figure.
4
2
Check that the stand neck is firmly connected.
5
3
Tightly fasten the connecting screw at the bottom of the stand base.
Place the protective Styrofoam (cushion) included in the package on the floor and place the product facing down on the Styrofoam, as shown in the image.
If Styrofoam is unavailable, use a thick sitting mat.
Hold the main body of the product with your hand as shown by the figure. Push the assembled stand into the main body in the direction of the arrow as shown in the figure.
- Caution
Do not hold the product upside down only by the stand.
19
Removing the Stand
― Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards.
: The product is curved. Placing pressure on the product when on a flat surface may damage the product. When the product is on the ground facing up or down, do not put pressure on it.
1
Place the protective Styrofoam (cushion) included in the package on the floor and place the product facing down on the Styrofoam, as shown in the image.
If Styrofoam is unavailable, use a thick sitting mat.
3
2 While holding the upper part of the monitor with one hand, pull the stand neck with the other hand in the arrow direction to detach the stand.
4
Turn the connecting screw at the bottom of the stand base to separate it.
Remove the stand neck from the stand base by pulling it in the direction of the arrow as shown in the figure.
20
Adjusting the Product Tilt
― The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.
0˚ (±2˚) ~ 15˚ (±2˚)
• You can adjust the product tilt.
• Hold the lower part of the product and adjust the tilt carefully.
21
Anti-theft Lock
― An anti-theft lock allows you to use the product securely even in public places.
― The locking device shape and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft locking device for details.
― The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.
To lock an anti-theft locking device:
2
1
Fix the cable of your anti-theft locking device to a heavy object such as a desk.
2
Put one end of the cable through the loop on the other end.
3
Insert the locking device into the anti-theft lock slot at the back of the product.
4
Lock the locking device.
An anti-theft locking device can be purchased separately.
Refer to the user guide provided with your anti-theft locking device for details.
Anti-theft locking devices can be purchased at electronics retailers or online.
22
Installing the Wall Mount Installing the Wall Mount Kit
The wall mount kit allows you to mount the product on the wall.
Purchase a compatible wall-mount kit to use with the product.
For detailed information on installing the wall mount, see the instructions provided with the wall mount.
We recommend you contact a technician for assistance when installing the wall mount bracket.
Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you elect to install the wall mount on your own.
23
Wall Mount Kit Specifications (VESA)
― Install your wall mount on a solid wall perpendicular to the floor. Before attaching the wall mount to surfaces other than plaster board, please contact your nearest dealer for additional information. If you install the product on a slanted wall, it may fall and result in severe personal injury. Samsung wall mount kits contain a detailed installation manual and all parts necessary for assembly are provided.
• For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ depending on the wall mount specifications.
• Do not fasten the screws too firmly. This may damage the product or cause the product to fall, leading to personal injury.
• Samsung is not liable for these kinds of accidents.
• Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or the consumer fails to follow the product installation instructions.
• Do not mount the product at more than a 15 degree tilt.
• Always have two people mount the product on a wall.
• Standard dimensions for wall mount kits are shown in the table below.
Unit: mm
Model name VESA screw hole specs (A * B) in millimeters
Standard Screw Quantity
S32E590C 200 x 200 M4 4
― Do not install your Wall Mount Kit while your product is turned on. It may result in personal injury due to electric shock.
― a : HOLDER-SCREW (4EA) (Optional)
24
Chapter 03
Connecting and Using a Source Device
Before Connecting
Check the following before you connect this product with other devices.
Pre-connection Checkpoints
― Before connecting a source device, read the user manual provided with it.
The number and locations of ports on source devices may differ from device to device.
― Do not connect the power cable until all connections are completed.
Connecting the power cable during connection may damage the product.
― Check the types of ports at the back of the product you want to connect.
Connecting and Using a PC
Select a connection method suitable for your PC.
― Connecting parts may differ in different products.
Connection Using the HDMI Cable
― Do not connect the power cable before connecting all other cables.
Ensure you connect a source device first before connecting the power cable.
HDMI IN 1, HDMI IN 2
1 Connect the HDMI IN 1 or HDMI IN 2 port on the back of the product to the HDMI port on the PC using an HDMI cable.
2 Connect the DC power adapter to the product and a power socket. Next, turn on the power switch on the PC.
3 Change the input source to HDMI 1 or HDMI 2 controlling the JOG button UP/DOWN, when input source is not set.
― Provided ports may vary depending on the product.
25
Connection Using an HDMI-DVI Cable
― Do not connect the power cable before connecting all other cables.
Ensure you connect a source device first before connecting the power cable.
Connection Using the DP Cable
― Do not connect the power cable before connecting all other cables.
Ensure you connect a source device first before connecting the power cable.
― A DP cable shorter under 1.5m in length is recommended. Using a cable longer than 1.5m can affect the picture quality.
HDMI IN 1, HDMI IN 2
DP IN
1
Connect the HDMI-DVI cable to the HDMI IN 1 or HDMI IN 2 port on the back of the product and the DVI port on the PC.
2
Connect the DC power adapter to the product and a power socket. Next, turn on the power switch on the PC.
3
Change the input source to HDMI 1 or HDMI 2 controlling the JOG button UP/DOWN, when input source is not set.
― Provided ports may vary depending on the product.
― The audio function is not supported if the source device is connected using the HDMI-DVI cable.
1 Connect the DP cable to the DP IN port on the back of the product and the DP port on the PC.
2 Connect the DC power adapter to the product and a power socket. Next, turn on the power switch on the PC.
3 Change the input source to DisplayPort controlling the JOG button UP/DOWN, when input source is not set.
― Provided ports may vary depending on the product.
26
Connecting to Headphones or Speakers
― Do not connect the power cable before connecting all other cables.
Ensure you connect a source device first before connecting the power cable.
1
Connect an audio output device such as headphones to port on the product.
― Provided ports may vary depending on the product.
Connecting the Power
Power connection using detachable DC power adapter
1
2
3
1
Connect the power cable to the DC power adapter. Then, connect the DC power adapter to the
DC 14V port on the back of the product.
2
Next, connect the power cable to the power outlet.
3
Press the JOG button on the back of the monitor to turn it on.
― Provided ports may vary depending on the product.
― The input voltage is switched automatically.
27
Driver Installation
― You can set the optimum resolution and frequency for this product by installing the corresponding drivers.
― To install the latest version of the product driver, download it from the Samsung Electronics website at http://www.samsung.com.
1 Click on the "Windows Driver" downloaded from the website.
2 Follow the instructions given on the screen to proceed with installation.
3 Select your product model from the list of models.
4 Go to Display Properties and check that the resolution and refresh rate are appropriate.
Refer to your Windows OS manual for further details.
Setting Optimum Resolution
An information message about setting optimum resolution will appear if you power on the product for the first time after purchase.
Select a language on the product and change the resolution on your PC to the optimum setting.
Setup Guide
Language
The optimal resolution for this monitor is as follows:
English
****x**** **Hz
Follow the above settings to set the resolution.
Current Resolution ****x****
Close
1 Select a language by moving the JOG button LEFT/RIGHT. Next, press the JOG button.
2 To hide the information message, press the JOG button.
― If the optimum resolution is not selected, the message will appear up to three times for a specified time even when the product is turned off and on again.
― The optimum resolution can also be selected in Control Panel on your PC.
28
Chapter 04
Screen Setup
Configure the screen settings such as brightness.
A detailed description of each function is provided. Refer to your product for details.
SAMSUNG MAGIC Bright
This menu provides an optimum picture quality suitable for the environment where the product will be used.
You can customize the brightness to suit your preferences.
― This menu is not available when Eco Saving Plus is enabled.
― This menu is not available when Game Mode is enabled.
― This menu is not available when Eye Saver Mode is enabled.
In PC mode
Picture
Brightness
Contrast
Sharpness
Color
HDMI Black Level
Eye Saver Mode
Custom
Standard
Cinema
Dynamic Contrast
Off
Set to an optimum picture quality suitable for the working environment.
Return
The displayed image may differ depending on the model.
Configuring SAMSUNG MAGIC Bright
1
When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button.
2
Move to Picture controlling the JOG button UP/DOWN and press the JOG button.
3
Move to SAMSUNG Bright controlling the JOG button UP/DOWN and press the JOG button.
• Custom : Customize the contrast and brightness as required.
• Standard : Obtain a picture quality suitable for editing documents or using Internet.
• Cinema : Obtain the brightness and sharpness of TVs suitable for enjoying video and DVD content.
• Dynamic Contrast : Obtain balanced brightness through automatic contrast adjustment.
29
In AV mode
Picture
Brightness
Contrast
Sharpness
Color
HDMI Black Level
Eye Saver Mode
Dynamic
Standard
Movie
Custom
The displayed image may differ depending on the model.
Off
Set to an optimum picture quality suitable for the working environment.
When the external input is connected through HDMI/DP and PC/AV Mode is set to AV , Bright has four automatic picture settings ( Dynamic , Standard , Movie and Custom ) that are preset at the factory. You can activate either Dynamic , Standard ,
Movie or Custom . You can select Custom which automatically recalls your personalized picture settings.
•
Dynamic : Select this mode to view a sharper image than in Standard mode.
•
Standard : Select this mode when the surroundings are bright. This also provides a sharp image.
•
Movie : Select this mode when the surroundings are dark. This will save power and reduce eye fatigue.
•
Custom : Select this mode when you want to adjust the image according to your preferences.
4
Move to the desired option controlling the JOG button UP/DOWN and press the JOG button.
5
The selected option will be applied.
Return
30
Brightness
You can adjust the general brightness of the picture. (Range: 0~100)
A higher value will make the picture appear brighter.
― This menu is not available when
SAMSUNG Bright is set to Dynamic Contrast mode.
― This menu is not available when Eco Saving Plus is set .
― This menu is not available when Eye Saver Mode is enabled.
Picture
Brightness
Contrast
Sharpness
Color
HDMI Black Level
Eye Saver Mode
Custom
100
75
60
Adjust the brightness level.
Values closer to 100 mean a brighter screen.
Off
Return
The displayed image may differ depending on the model.
Configuring Brightness
1 When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button.
2
Move to Picture controlling the JOG button UP/DOWN and press the JOG button.
3
Move to Brightness controlling the JOG button UP/DOWN and press the JOG button.
4
Adjust the Brightness controlling the JOG button LEFT/RIGHT.
5
The selected option will be applied.
31
Contrast
Adjust the contrast between the objects and background. (Range: 0~100)
A higher value will increase the contrast to make the object appear clearer.
― This option is not available when
SAMSUNG Bright is in Cinema or
Dynamic Contrast mode.
― This menu is not available when Game Mode is enabled.
Picture
Brightness
Contrast
Sharpness
Color
HDMI Black Level
Eye Saver Mode
Custom
100
75
60
Adjust the contrast level. Values closer to 100 mean a bigger light/dark contrast.
Off
Return
The displayed image may differ depending on the model.
Configuring Contrast
1 When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button.
2
Move to Picture controlling the JOG button UP/DOWN and press the JOG button.
3
Move to Contrast controlling the JOG button UP/DOWN and press the JOG button.
4
Adjust the Contrast controlling the JOG button LEFT/RIGHT.
5
The selected option will be applied.
32
Sharpness
Make the outline of objects more clear or blurry. (Range: 0~100)
A higher value will make the outline of objects clearer.
― This option is not available when
SAMSUNG Bright is in Cinema or
Dynamic Contrast mode.
― This menu is not available when Game Mode is enabled.
Picture
Brightness
Contrast
Sharpness
Color
HDMI Black Level
Eye Saver Mode
Custom
100
75
60
Adjust the sharpness of the picture. Values closer to 100 mean a sharper image.
Off
Return
The displayed image may differ depending on the model.
Configuring Sharpness
1 When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button.
2
Move to Picture controlling the JOG button UP/DOWN and press the JOG button.
3
Move to Sharpness controlling the JOG button UP/DOWN and press the JOG button.
4
Adjust the Sharpness controlling the JOG button LEFT/RIGHT.
5
The selected option will be applied.
33
Color
A detailed description of each function is provided. Refer to your product for details.
― Adjust the tint of the screen. This menu is not available when
SAMSUNG to Cinema or Dynamic Contrast mode.
Bright is set
― This menu is not available when Game Mode is enabled.
― This menu is not available when Eye Saver Mode is enabled.
Picture
Brightness
Contrast
Sharpness
Color
HDMI Black Level
Eye Saver Mode
Custom
100
75
60
Configure color settings.
Off
Return
Color
Red
Green
Blue
Color Tone
Gamma
50
50
50
Normal
Mode1
Adjust the red saturation level.
Values closer to
100 mean greater intensity for the color.
Configuring Color
1 When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button.
2
Move to Picture controlling the JOG button UP/DOWN and press the JOG button.
3
Move to Color controlling the JOG button UP/DOWN and press the JOG button.
• Red : Adjust the red saturation level. Values closer to 100 mean greater intensity for the color.
• Green : Adjust the green saturation level. Values closer to 100 mean greater intensity for the color.
• Blue : Adjust the blue saturation level. Values closer to 100 mean greater intensity for the color.
• Color Tone : Select a color tone that best suits your viewing needs.
Cool 2 : Set the color temperature to be cooler than Cool 1 .
Cool 1 : Set the color temperature to be cooler than Normal mode.
Normal : Display the standard color tone.
Warm 1 : Set the color temperature to be warmer than Normal mode.
Warm 2 : Set the color temperature to be warmer than Warm 1 .
Custom : Customize the color tone.
― When the external input is connected through HDMI/DP and PC/AV Mode is set to AV , Color Tone has four color temperature settings ( Cool , Normal , Warm and Custom ).
• Gamma : Adjust the middle level of luminance.
Mode1 / Mode2 / Mode3
4
Move to the desired option by controlling the JOG button and then press the JOG button.
5
The selected option will be applied.
Return
The displayed image may differ depending on the model.
34
HDMI Black Level
If a DVD player or set-top box is connected to the product via HDMI, image quality degradation (contrast/color degradation, black level, etc.) may occur, depending on the connected source device. In such case, HDMI Black Level can be used to adjust the image quality.
If this is the case, correct the degraded picture quality using HDMI Black Level .
― This function is only available in HDMI 1 or HDMI 2 mode.
Picture
Brightness
Contrast
Sharpness
Color
HDMI Black Level
Eye Saver Mode
Normal
Low
Custom
100
75
60
Optimize HDMI picture brightness and contrast by adjusting the black level of the video signal.
해제
Return
Configuring the HDMI Black Level Settings
1 When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button.
2
Move to Picture controlling the JOG button UP/DOWN and press the JOG button.
3
Move to HDMI Black Level controlling the JOG button UP/DOWN and press the JOG button.
• Normal : Select this mode when there is no contrast ratio degradation.
• Low : Select this mode to reduce the black level and increase the white level when there is a contrast ratio degradation.
4 Move to the desired option controlling the JOG button UP/DOWN and press the JOG button.
5 The selected option will be applied.
― HDMI Black Level may not be compatible with some source devices.
― The HDMI Black Level feature is only activated at a certain AV resolution, such as 720P and 1080P.
The displayed image may differ depending on the model.
35
Eye Saver Mode
Set to an optimum picture quality suitable for eye relaxation.
TÜV Rheinland “Low Blue Light Content” is a certification for products which meet requirements for lower blue light levels. When Eye Saver Mode is ' On ', the blue light that wavelength is around 400nm will become lower and lower, and one hour later it will approach the optimum picture quality suitable for eye relaxation.
At the same time, the blue light level is lower than in the default settings, and it was tested by TÜV Rheinland and certified as it met the requirements of TÜV
Rheinland “Low Blue Light Content” standards.
Picture
Brightness
Contrast
Sharpness
Color
HDMI Black Level
Eye Saver Mode
Off
On
Custom
100
75
60
Set to an optimum picture quality suitable for eye relaxation.
Return
The displayed image may differ depending on the model.
Configuring Eye Saver Mode
1 When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button.
2
Move to Picture controlling the JOG button UP/DOWN and press the JOG button.
3
Move to Eye Saver Mode controlling the JOG button UP/DOWN and press the JOG button.
4
Move to the desired option controlling the JOG button UP/DOWN and press the JOG button.
5
The selected option will be applied.
36
Game Mode
Configure the product screen settings for game mode.
Use this feature when playing games on a PC or when a game console such as
PlayStation™ or Xbox™ is connected.
― This menu is not available when Eye Saver Mode is enabled.
Picture
Game Mode
Response Time
Picture Size
Screen Adjustment
Off
On
Always On
Optimizes image settings for playing games.
Configuring Game Mode
1 When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button.
2
Move to Picture controlling the JOG button UP/DOWN and press the JOG button.
3
Move to Game Mode controlling the JOG button UP/DOWN and press the JOG button.
4
Move to the desired option controlling the JOG button UP/DOWN and press the JOG button.
5
The selected option will be applied.
― When the monitor turns off, enters power-saving mode or changes input sources, Game Mode turns Off even if it is set to
On .
― If you want to keep Game Mode enabled all the time, select Always On .
Return
The displayed image may differ depending on the model.
37
Response Time
Accelerate the panel response rate to make video appear more vivid and natural.
― It is best to set Response Time to Standard or Faster when you are not viewing a movie.
Picture
Game Mode
Response Time
Picture Size
Screen Adjustment
Standard
Faster
Fastest
Accelerate the panel response rate to make video appear more vivid and natural.
Configuring the Response Time
1 When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button.
2
Move to Picture controlling the JOG button UP/DOWN and press the JOG button.
3
Move to Response Time controlling the JOG button UP/DOWN and press the JOG button.
• Standard / Faster / Fastest
4
Move to the desired option controlling the JOG button UP/DOWN and press the JOG button.
5
The selected option will be applied.
Return
The displayed image may differ depending on the model.
38
Picture Size
Change the picture size.
In PC mode
Picture
Game Mode
Response Time
Picture Size
Screen Adjustment
Auto
Wide
Off
Choose the size and aspect ratio of the picture displayed on screen.
Changing the Picture Size
1 When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button.
2
Move to Picture controlling the JOG button UP/DOWN and press the JOG button.
3
Move to Picture Size controlling the JOG button UP/DOWN and press the JOG button.
In PC mode
• Auto : Display the picture according to the aspect ratio of the input source.
• Wide : Display the picture in full screen regardless of the aspect ratio of the input source.
Return
The displayed image may differ depending on the model.
39
In AV mode
Picture
Game Mode
Response Time
Picture Size
Screen Adjustment
4:3
16:9
Screen Fit
The displayed image may differ depending on the model.
Off
Choose the size and aspect ratio of the picture displayed on screen.
Return
In AV mode
• 4:3 : Display the picture with an aspect ratio of 4:3. Suitable for videos and standard broadcasts.
• 16:9 : Display the picture with an aspect ratio of 16:9.
• Screen Fit : Display the picture with the original aspect ratio without cutting off.
― The function may not be supported depending on the ports provided with the product.
― Changing the screen size is available when the following conditions are satisfied.
― A digital output device is connected using the HDMI cable.
― A digital output device is connected using the DP cable.
― The input signal is 480p, 576p, 720p, or 1080p and monitor can display normally
(Not every model can support all of these signals.).
― This can only be set when the external input is connected through HDMI, DP and PC/AV Mode is set to AV .
4
Move to the desired option controlling the JOG button UP/DOWN and press the JOG button.
5
The selected option will be applied.
40
Screen Adjustment
― This menu is only available when Picture Size is set to Screen Fit in AV Mode.
― When a 480P or 576P or 720P or 1080P signal is input in AV mode and the monitor can display normally, select Screen Fit to adjust horizontal position in
0-6 levels.
Screen Adjustment
H-Position
V-Position
3
3
Move the image displayed on the screen to the left or right.
Configuring H-Position & V-Position
H-Position : Move the screen to the left or right.
V-Position : Move the screen up or down.
1
When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button.
2
Move to Picture controlling the JOG button UP/DOWN and press the JOG button.
3
Move to Screen Adjustment controlling the JOG button UP/DOWN and press the JOG button.
4
Move to the H-Position or V-Position controlling the JOG button UP/DOWN and press the JOG button.
5
Adjust the H-Position or V-Position controlling the JOG button LEFT/RIGHT and press the JOG button.
6
The selected option will be applied.
Screen Adjustment
H-Position
V-Position
Return
3
3
Move the image displayed on the screen up or down.
Return
The displayed image may differ depending on the model.
41
Chapter 05
Coordinating OSD
A detailed description of each function is provided. Refer to your product for details.
Transparency
Set the transparency for the menu windows.
OnScreen Display
Transparency
Language
Display Time
Off
On
The displayed image may differ depending on the model.
한국어
Configure the transparency of the menu windows.
Changing Transparency
1
When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button.
2
Move to OnScreen Display controlling the JOG button UP/DOWN and press the JOG button.
3
Move to Transparency controlling the JOG button UP/DOWN and press the JOG button.
• Off / On
4
Move to the desired option controlling the JOG button UP/DOWN and press the JOG button.
5
The selected option will be applied.
Return
42
Language
Set the menu language.
― A change to the language setting will only be applied to the onscreen menu display.
― It will not be applied to other functions on your PC.
OnScreen Display
Transparency
Language
Display Time
Deutsch
English
Español
Français
Italiano
20 초
Set the menu language.
Configuring Language
1 When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button.
2
Move to OnScreen Display controlling the JOG button UP/DOWN and press the JOG button.
3
Move to Language controlling the JOG button UP/DOWN and press the JOG button.
4
Move to the desired option controlling the JOG button UP/DOWN and press the JOG button.
5
The selected option will be applied.
Return
The displayed image may differ depending on the model.
43
Display Time
Set the on-screen display (OSD) menu to automatically disappear if the menu is not used for a specified period of time.
Display Time can be used to specify the time after which you want the OSD menu to disappear.
OnScreen Display
Transparency
Language
Display Time
5 sec
10 sec
20 sec
200 sec
On
Set how long the menu window will remain on screen for when it is not in use.
Configuring Display Time
1 When the Function Key Guide appears, select to display the corresponding menu screen.
2
Move to OnScreen Display controlling the JOG button UP/DOWN and press the JOG button.
3
Move to Display Time controlling the JOG button UP/DOWN and press the JOG button.
• 5 sec / 10 sec / 20 sec / 200 sec
4
Move to the desired option controlling the JOG button UP/DOWN and press the JOG button.
5
The selected option will be applied.
Return
The displayed image may differ depending on the model.
44
Chapter 06
Setup and Reset
A detailed description of each function is provided. Refer to your product for details.
Sound
System
Sound
Eco Saving Plus
Off Timer
PC/AV Mode
DisplayPort Ver.
Source Detection
Key Repeat Time
Sound
Volume
Sound Mode
Select Sound
Off
1.2
Auto
Acceleration
50
Standard
Stereo
Return
Configuring Volume
1
When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button.
2
Move to System controlling the JOG button UP/DOWN and press the JOG button.
3
Move to Sound controlling the JOG button UP/DOWN and press the JOG button.
4
Adjust the Volume controlling the JOG button LEFT/RIGHT.
5
The selected option will be applied.
Return
The displayed image may differ depending on the model.
45
Configuring Sound Mode
― Applicable when speakers are connected.
Sound
Volume
Sound Mode
Select Sound
Standard
Music
Movie
Clear Voice
The displayed image may differ depending on the model.
Return
1
When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button.
2
Move to System controlling the JOG button UP/DOWN and press the JOG button.
3
Move to Sound controlling the JOG button UP/DOWN and press the JOG button.
4
Move to Sound Mode controlling the JOG button UP/DOWN and press the JOG button.
• Standard : Selects the normal sound mode.
• Music : Emphasizes music over voices.
• Movie : Provides the best sound for movies.
• Clear Voice : Emphasizes voices over other sounds.
5 Move to the desired option controlling the JOG button UP/DOWN and press the JOG button.
6 The selected option will be applied.
46
Configuring Select Sound
Sound
Volume
Sound Mode
Select Sound Stereo
Left Channel
Right Channel
50
Return
1
When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button.
2
Move to System controlling the JOG button UP/DOWN and press the JOG button.
3
Move to Sound controlling the JOG button UP/DOWN and press the JOG button.
4
Move to Select Sound controlling the JOG button UP/DOWN and press the JOG button.
• Stereo : Enable the sound both from the left and right speakers.
• Left Channel : Set the left and right speakers to play only the left channel of the sound source.
• Right Channel : Set the left and right speakers to play only the right channel of the sound source.
5
Move to the desired option controlling the JOG button UP/DOWN and press the JOG button.
6
The selected option will be applied.
The displayed image may differ depending on the model.
47
Eco Saving Plus
The Eco Saving Plus function reduces power consumption by controlling the electric current used by the monitor panel.
― This option is not available when
SAMSUNG Bright is in Dynamic Contrast mode.
― This menu is not available when Game Mode is enabled.
― This menu is not available when Eye Saver Mode is enabled.
System
Sound
Eco Saving Plus
Off Timer
PC/AV Mode
DisplayPort Ver.
Source Detection
Key Repeat Time
Off
Auto
Low
High
해제
Adjust the power consumption of the product to save energy.
자동
Stand-by
Return
The displayed image may differ depending on the model.
Configuring Eco Saving Plus
1
When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button.
2
Move to System controlling the JOG button UP/DOWN and press the JOG button.
3
Move to Eco Saving Plus controlling the JOG button UP/DOWN and press the JOG button.
• Off : Deactivate the Eco Saving Plus function.
• Auto : The power consumption will automatically be reduced by about 10% over the current setting.
(The reduction of power consumption depends on the customer screen brightness condition.)
• Low : The power consumption will be reduced by 25% over the default setting.
• High : The power consumption will be reduced by 50% over the default setting.
4
Move to the desired option controlling the JOG button UP/DOWN and press the JOG button.
5
The selected option will be applied.
48
Off Timer
You can set the product to automatically turn off.
System
Sound
Eco Saving Plus
Off Timer
PC/AV Mode
DisplayPort Ver.
Source Detection
Key Repeat Time
Off
1.2
Acceleration
Auto
Enable or disable the Off Timer.
Return
Configuring Off Timer
1 When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button.
2
Move to System controlling the JOG button UP/DOWN and press the JOG button.
3
Move to Off Timer controlling the JOG button UP/DOWN and press the JOG button.
• Off : Deactivate the off timer so that the product does not power off automatically.
• On : Activate the off timer so that the product powers off automatically.
4 Move to the desired option controlling the JOG button UP/DOWN and press the JOG button.
5 The selected option will be applied.
Off Timer
Off Timer
Turn Off After
Enable or disable the Off Timer.
Return
The displayed image may differ depending on the model.
49
Off Timer
Off Timer
Turn Off After
The displayed image may differ depending on the model.
Off
4h
Set the monitor to automatically turn off after a certain time period.
Return
Configuring Turn Off After
― This option is only available when Off Timer is set to On .
1
When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button.
2
Move to System controlling the JOG button UP/DOWN and press the JOG button.
3
Move to Off Timer controlling the JOG button UP/DOWN and press the JOG button.
4
Move to Turn Off After controlling the JOG button UP/DOWN and press the JOG button.
5
Adjust the Turn Off After controlling the JOG button LEFT/RIGHT.
6
The selected option will be applied.
― The off timer can be set within a range of 1 to 23 hours. The product will automatically power off after the specified number of hours.
― For products for the market in some regions, the Off Timer is set to automatically activate 4 hours after the product powers on. This is done in accordance with power supply regulations. If you do not want the timer to activate, go to
MENU System and set Off Timer to Off .
50
PC/AV Mode
Set PC/AV Mode to AV . The picture size will be enlarged.
This option is useful when you view a movie.
System
Sound
Eco Saving Plus
Off Timer
PC/AV Mode
DisplayPort Ver.
Source Detection
Key Repeat Time
Off
1.2
Acceleration
Auto
Set to AV to enlarge the picture.
Return
― Supplied for the wide models only such as 16:9 or 16:10.
― If the monitor is in HDMI 1 , HDMI 2 or DisplayPort mode and the screen says Check Signal Cable or power saving mode activates, press the JOG button to display the function-button screen and then select the icon. You can select PC or AV .
Configuring PC/AV Mode
1
When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button.
2 Move to System controlling the JOG button UP/DOWN and press the JOG button.
3 Move to PC/AV Mode controlling the JOG button UP/DOWN and press the JOG button.
4 Move to the HDMI 1 , HDMI 2 , DisplayPort controlling the JOG button UP/DOWN and press the JOG button.
• Set to PC when connected to a PC.
• Set to AV when connected to an AV device.
5
Move to the desired option controlling the JOG button UP/DOWN and press the JOG button.
6
The selected option will be applied.
PC/AV Mode
DisplayPort
HDMI 1
HDMI 2
PC
AV
Select the PC/
AV mode for the
DisplayPort source.
Return
The displayed image may differ depending on the model.
51
DisplayPort Ver.
Select your Displayport. Displayport 1.1 supports High Bit Rate 1, while 1.2 supports High Bit Rate 2.
System
Sound
Eco Saving Plus
Off Timer
PC/AV Mode
DisplayPort Ver.
Source Detection
Key Repeat Time
1.1
1.2
자동
가속반복
Off
Select your
Displayport.
Displayport 1.1 supports HBR 1, while 1.2 supports
HBR 2.
Return
The displayed image may differ depending on the model.
― Incorrect settings may cause the screen to go blank. If this occurs, check the device specifications.
― If the monitor is in HDMI 1 , HDMI 2 or DisplayPort mode and the screen says Check Signal Cable or power saving mode activates, press the JOG button to display the function-button screen and then select the icon. You can select 1.1
or 1.2
.
Configuring DisplayPort Ver.
1
When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button.
2 Move to System controlling the JOG button UP/DOWN and press the JOG button.
3 Move to DisplayPort Ver.
controlling the JOG button UP/DOWN and press the JOG button.
• 1.1
/ 1.2
4
Move to the desired option controlling the JOG button UP/DOWN and press the JOG button.
5
The selected option will be applied.
52
Source Detection
You can activate Source Detection .
System
Sound
Eco Saving Plus
Off Timer
PC/AV Mode
DisplayPort Ver.
Source Detection
Key Repeat Time
Auto
Manual
자동
가속반복
Off
Decide how input sources will be detected.
Return
The displayed image may differ depending on the model.
Configuring Source Detection
1 When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button.
2
Move to System controlling the JOG button UP/DOWN and press the JOG button.
3
Move to Source Detection controlling the JOG button UP/DOWN and press the JOG button.
• Auto : The input source is automatically recognized.
• Manual : Manually select an input source.
4 Move to the desired option controlling the JOG button UP/DOWN and press the JOG button.
5 The selected option will be applied.
53
Key Repeat Time
Control the response rate of a button when the button is pressed.
System
Sound
Eco Saving Plus
Off Timer
PC/AV Mode
DisplayPort Ver.
Source Detection
Key Repeat Time
Acceleration
1 sec
2 sec
No Repeat
자동
가속반복
Off
Configure the response rate of a button when the button is pressed.
Return
The displayed image may differ depending on the model.
Configuring Key Repeat Time
1 When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button.
2
Move to System controlling the JOG button UP/DOWN and press the JOG button.
3
Move to Key Repeat Time controlling the JOG button UP/DOWN and press the JOG button.
• Acceleration , 1 sec , or 2 sec can be selected. If No Repeat is selected, a command responds only once when a button is pressed.
4
Move to the desired option controlling the JOG button UP/DOWN and press the JOG button.
5
The selected option will be applied.
54
Power LED On
Configure the settings to enable or disable the power LED located at the lower part of the product.
System
Power LED On
Reset All
Working
Stand-by
Set the status of the power LED.
Configuring Power LED On
1 When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button.
2
Move to System controlling the JOG button UP/DOWN and press the JOG button.
3
Move to Power LED On controlling the JOG button UP/DOWN and press the JOG button.
• Working : The power LED is on when the product is turned on.
• Stand-by : The power LED is on when the product is turned off.
4 Move to the desired option controlling the JOG button UP/DOWN and press the JOG button.
5 The selected option will be applied.
Return
The displayed image may differ depending on the model.
55
Reset All
Return all the settings for the product to the default factory settings.
System
Power LED On
Reset All
Stand-by
Return all the settings for the product to the default factory settings.
Initializing Settings (Reset All)
1 When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button.
2
Move to System controlling the JOG button UP/DOWN and press the JOG button.
3
Move to Reset All controlling the JOG button UP/DOWN and press the JOG button.
4
Move to the desired option controlling the JOG button LEFT/RIGHT and press the JOG button.
5
The selected option will be applied.
Return
All the menu settings will be reset to default.
Are you sure you want to reset?
Yes No
The displayed image may differ depending on the model.
56
Chapter 07
Information Menu and Others
A detailed description of each function is provided. Refer to your product for details.
Information
View the current input source, frequency and resolution.
Picture
OnScreen Display
System
Information
Information
LS32E590CS/XF
S/N:***********
DisplayPort
**** x ****
**kHz **Hz PP
Displaying Information
1
When the Function Key Guide appears, select by moving the JOG button UP. Next, press the JOG button.
2
Move to Information controlling the JOG button UP/DOWN and press the JOG button. The current input source, frequency and resolution will appear.
Exit
The displayed image may differ depending on the model.
57
Configuring Brightness, Contrast and Sharpness from the Initial
Screen
You can adjust Brightness , Contrast or Sharpness by moving the JOG button up or down, if no OSD menu is displayed.
Sharpness
Brightness
Contrast
100
Brightness
― This menu is not available when
SAMSUNG Bright is set to Dynamic Contrast mode.
― This menu is not available when Eco Saving Plus is enabled.
― This menu is not available when Eye Saver Mode is enabled.
Contrast
― This menu is not available when
SAMSUNG Bright is in Cinema or Dynamic Contrast mode.
― This menu is not available when Game Mode is enabled.
Sharpness
― This menu is not available when
SAMSUNG Bright is in Cinema or Dynamic Contrast mode.
― This menu is not available when Game Mode is enabled.
1
Move the JOG button UP/DOWN to select Brightness , Contrast or Sharpness .
2
Move the JOG button LEFT/RIGHT to adjust the Brightness , Contrast or Sharpness setting.
The displayed image may differ depending on the model.
58
Configuring Volume in the Initial
Screen
Adjust the Volume by moving the JOG button when the Direct Key Guide is displayed on the screen.
Volume 50
Mute
The displayed image may differ depending on the model.
1
Adjust the Volume controlling the JOG button LEFT/RIGHT.
― If the audio quality of a connected input device is poor, the Auto Mute function on the product may mute the sound or cause choppy audio when applying the headphones or speakers. Set the input volume for the input device to at least 20% and control the volume using the volume control (JOG button LEFT/RIGHT) on the product.
― What is Auto Mute?
The function mutes the audio to improve sound effect when there is sound noise or when the input signal is weak, usually due to a problem with the volume of an input device.
― To activate the Mute function, access the Volume control screen, then use the JOG button to move the focus down.
To deactivate the Mute function, access the Volume control screen, then increase or decrease the Volume .
― The Mute function is disabled if you activate power-saving mode or turn the product off and then on again.
59
Chapter 08
Installing the Software
Easy Setting Box
Easy Setting Box
Easy Setting Box enables users to use the monitor by partitioning multiple sections.
Installing the Software
1
To install the latest version of Easy Setting Box, download it from the Samsung Electronics website at http://www.samsung.com.
2
Select the Easy Setting Box setup program.
3
When the Installation Wizard appears, click Next.
4
Follow the instructions given on the screen to proceed with installation.
― The software may not work properly if you do not restart the computer after the installation.
― The Easy Setting Box icon may not appear depending on the computer system and the product specifications.
― If the shortcut icon does not appear, press the F5 key.
Restrictions and Problems with the Installation (Easy Setting Box)
The Easy Setting Box installation may be affected by the Graphics Card, Motherboard and the
Networking Environment.
System Requirements
OS
• Windows Vista 32Bit/64Bit
• Windows 7 32Bit/64Bit
• Windows 8 32Bit/64Bit
• Windows 8.1 32Bit/64Bit
Hardware
• At least 32MB of memory
• At least 60MB of free space on the hard disk drive
Removing the Software
Click Start, select Settings/Control Panel, and then double-click Add or Remove Programs.
Select Easy Setting Box from the program list and click the Add/Delete button.
60
Chapter 09
Troubleshooting Guide
Requirements Before Contacting Samsung Customer Service Center
Before calling Samsung Customer Service
Center, test your product as follows. If the problem persists, contact Samsung
Customer Service Center.
If the screen remains blank, check the PC system, video controller and cable.
Testing the Product
Check if your product is operating normally by using the product test function.
If the screen is turned off and the power indicator blinks even though the product is properly connected to a PC, perform a self-diagnosis test.
1
Power off both the PC and product.
2
Disconnect the cables from the product.
3
Power on the product.
4
If the message Check Signal Cable appears, the product is working normally.
Checking the Resolution and Frequency
For a mode that exceeds the supported resolution(refer to Standard Signal Mode Table ), the message
Not Optimum Mode will appear for a short time.
― The displayed resolution may vary depending on the product or PC system settings.
61
Check the following.
Installation issue (PC mode)
Issues Solutions
The screen keeps switching on and off.
Check the cable connection between the product and PC, and ensure the connectors are locked.
Blank spaces are found on all four sides of the screen when an HDMI or HDMI-DVI cable is connected to the product and
PC.
The blank spaces found on the screen have nothing to do with the product.
Blank spaces on the screen are caused by the PC or graphics card. To resolve the problem, adjust the screen size in the HDMI or DVI settings for the graphics card.
If the graphics card settings menu does not have an option to adjust the screen size, update the graphics card driver to the latest version.
(Please contact the graphics card or computer manufacturer for further details about how to adjust the screen settings.)
Screen issue
Issues
The power LED is off. The screen will not switch on.
The message Check Signal Cable appears.
Not Optimum Mode is displayed.
The images on the screen look distorted.
Solutions
Check that the power cable is connected properly.
Check that the cable is properly connected to the product.
Check that the device connected to the product is powered on.
This message appears when the signal from the graphics card exceeds the maximum resolution or frequency for the product.
Change the maximum resolution and frequency to suit the product performance, referring to Standard
Signal Mode Table (
Check the cable connection to the product.
62
Issues
The screen is not clear. The screen is blurry.
The screen appears unstable and shaky.
There are shadows or ghost images left on the screen.
The screen is too bright. The screen is too dark.
Screen color is inconsistent.
The colors on the screen have a shadow and are distorted.
White does not really look white.
There is no image on the screen and the power LED blinks every 0.5 to 1 second.
Text is blurry.
Video playback is choppy.
Solutions
Remove any accessories (video extension cable, etc.) and try again.
Set the resolution and frequency to the recommended level.
Check that the resolution and frequency for the PC are within the range of resolution and frequency compatible with the product. Next, if required, change the settings, referring to Standard Signal Mode
Table (
Information menu on the product.
Adjust Brightness and Contrast .
Change the Color settings.
Change the Color settings.
Change the Color settings.
The product is operating in power-saving mode.
Press any key on the keyboard or move the mouse to return to normal operating mode.
If using a Windows OS (e.g. Windows 7, Windows 8 or Windows 8.1): Go to Control Panel Fonts
Adjust ClearType text and change Turn on ClearType.
Playback of high-definition large video files can be choppy. This may be because the video player is not optimized for the computer resource.
Try playing the file on another video player.
63
Sound issue
Issues
There is no sound.
The volume is too low.
Video is available but there is no sound.
Solutions
Check the connection of the audio cable or adjust the volume.
Check the volume.
Adjust the volume.
If the volume is still low after turning it up to the maximum level, adjust the volume on your PC sound card or software program.
Sound cannot be heard if a HDMI-DVI cable is used to connect the input device.
Connect the device using an HDMI cable or a DP cable.
Source device issue
Issues
A beeping sound is heard when my PC is booting.
Solutions
If a beeping sound is heard when your PC is booting, have your PC serviced.
― The LED lights on the frame of the product may be seen depending on the user's viewing angle. The light is harmless to people and has no bearing on product features and performance. The product is safe to use.
64
Refer to the user manual for your PC or graphics card for further instructions on adjustment.
Q & A
Question
How can I change the frequency?
How can I change the resolution?
Answer
Set the frequency on your graphics card.
• Windows XP: Go to Control Panel Appearance and Themes Display Settings
Advanced Monitor, and adjust Refresh rate under Monitor settings.
• Windows ME/2000: Go to Control Panel Display Settings Advanced Monitor, and adjust Refresh rate under Monitor settings.
• Windows Vista: Go to Control Panel Appearance and Personalization Personalization
Display Settings Advanced Settings Monitor, and adjust Refresh rate under
Monitor settings.
• Windows 7: Go to Control Panel Appearance and Personalization Display Screen
Resolution Advanced settings Monitor, and adjust Refresh rate under Monitor
settings.
• Windows 8(Windows 8.1): Go to Settings Control Panel Appearance and
Personalization Display Screen Resolution Advanced settings Monitor, and adjust Refresh rate under Monitor settings.
• Windows XP: Go to Control Panel Appearance and Themes Display Settings, and adjust the resolution.
• Windows ME/2000: Go to Control Panel Display Settings, and adjust the resolution.
• Windows Vista: Go to Control Panel Appearance and Personalization Personalize
Display Settings, and adjust the resolution.
• Windows 7: Go to Control Panel Appearance and Personalization Display Adjust
Resolution, and adjust the resolution.
• Windows 8(Windows 8.1): Go to Settings Control Panel Appearance and
Personalization Display Adjust Resolution, and adjust the resolution.
65
Question
How do I set power-saving mode?
Answer
• Windows XP: Set power-saving mode in Control Panel Appearance and Themes Display
Screen Saver Settings or BIOS SETUP on the PC.
• Windows ME/2000: Set power-saving mode in Control Panel Display Screen Saver
Settings or BIOS SETUP on the PC.
• Windows Vista: Set power-saving mode in Control Panel Appearance and Personalization
Personalize Screen Saver Settings or BIOS SETUP on the PC.
• Windows 7: Set power-saving mode in Control Panel Appearance and Personalization
Personalize Screen Saver Settings or BIOS SETUP on the PC.
• Windows 8(Windows 8.1): Set power-saving mode in Settings Control Panel Appearance
and Personalization Personalize Screen Saver Settings or BIOS SETUP on the PC.
66
Chapter 10
Specifications
- Size
- Display area
H
V
- Dimensions (W x H x D)
D
General
Model Name
Panel
Dimensions (W x H x D) /
Weight
Maximum Pixel Clock
Power Supply
Signal connectors
Size
Display area
Pixel Pitch
Without Stand
With Stand
S32E590C
80.1 cm
698.40 mm (H) x 392.85 mm (V)
0.36375 mm (H) x 0.36375 mm (V)
729.1 x 425.1 x 90.6 mm / 6.0 kg
729.1 x 523.9 x 214.3 mm / 6.9 kg
148.5 MHz (HDMI, DisplayPort)
AC 100 - 240 V ~ (+/- 10 %), 50/60 Hz ± 3 Hz
Refer to the label at the back of the product as the standard voltage can vary in different countries.
HDMI, DP Port
H
W
67
Model Name
Environmental conditions Operating
S32E590C
Temperature: 10 C – 40 C (50 F – 104 F)
Humidity: 10 % – 80 %, non-condensing
Storage Temperature: -20 C – 45 C (-4 F – 113 F)
Humidity: 5 % – 95 %, non-condensing
― Plug-and-Play
This monitor can be installed and used with any Plug-and-Play compatible systems. Two-way data exchange between the monitor and PC system optimizes the monitor settings. Monitor installation takes place automatically. However, you can customize the installation settings if desired.
― Panel Dots (Pixels)
Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may be brighter or darker on the LCD panel. This does not affect product performance.
― The above specifications are subject to change without notice to improve quality.
― This device is a Class B digital apparatus.
68
PowerSaver
The power-saving function of this product reduces power consumption by switching off the screen and changing the color of the power LED if the product is not used for a specified period of time. The power is not turned off in power-saving mode. To switch the screen back on, press any key on the keyboard or move the mouse. Powersaving mode only functions when the product is connected to a PC with a power-saving function.
PowerSaver Power saving mode Power off (Power button)
Power Indicator
Power Consumption
(Energy Star Test Condition)
Off Blinking On
Power Consumption 34 W Less than 0.3 W Less than 0.3 W
― The displayed power consumption level can vary in different operating conditions or when settings are changed.
― ENERGY STAR® is a US registered mark of the United States Environmental Protection Agency.
Energy Star power is measured with the test method in the current Energy Star® Standard.
― SOG(Sync On Green) is not supported.
― To reduce the power consumption to 0, disconnect the power cord. Disconnect the power cable if you will not be using the product for an extended period of time (during vacation, etc.)
69
This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Using a resolution other than the specified resolution may degrade the picture quality. To avoid this, it is recommended that you select the optimum resolution specified for your product.
Standard Signal Mode Table
Model Name
Synchronization
Resolution
Horizontal Frequency
Vertical Frequency
Optimum resolution
Maximum resolution
S32E590C
30 – 81 kHz
56 – 75 Hz (HDMI)
1920 x 1080 @ 60 Hz
1920 x 1080 @ 60 Hz
If a signal that belongs to the following standard signal modes is transmitted from your PC, the screen will automatically be adjusted. If the signal transmitted from the
PC does not belong to the standard signal modes, the screen may be blank even though the power LED turns on. In such a case, change the settings according to the following table by referring to the graphics card user manual.
Resolution Horizontal Frequency
(kHz)
Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V)
IBM, 720 x 400 31.469 70.087 28.322 -/+
MAC, 640 x 480
MAC, 832 x 624
MAC, 1152 x 870
VESA, 640 x 480
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
35.000
49.726
68.681
31.469
37.861
37.500
35.156
37.879
48.077
46.875
48.363
66.667
74.551
75.062
59.940
72.809
75.000
56.250
60.317
72.188
75.000
60.004
30.240
57.284
100.000
25.175
31.500
31.500
36.000
40.000
50.000
49.500
65.000
+/+
+/+
+/+
-/-
-/-
+/+
-/-
-/-
-/-
-/-
-/-
70
Resolution
Horizontal Frequency
The time required to scan a single line from the left to the right side of the screen is called a horizontal cycle. The reciprocal number of a horizontal cycle is called horizontal frequency. Horizontal frequency is measured in kHz.
Vertical Frequency
Repeating the same picture dozens of times per second allows you to view natural pictures. The repeat frequency is called "vertical frequency" or "refresh rate" and is indicated in Hz.
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 x 720
VESA, 1280 x 800
VESA, 1280 x 1024
VESA, 1280 x 1024
VESA, 1440 x 900
VESA, 1600 x 900 RB
VESA, 1680 x 1050
VESA, 1920 x 1080
Horizontal Frequency
(kHz)
63.981
79.976
55.935
60.000
65.290
67.500
56.476
60.023
67.500
45.000
49.702
Vertical Frequency (Hz) Pixel Clock (MHz)
60.020
75.025
59.887
60.000
59.954
60.000
70.069
75.029
75.000
60.000
59.810
75.000
78.750
108.000
74.250
83.500
108.000
135.000
106.500
108.000
146.250
148.500
Sync Polarity (H/V)
+/+
-/+
+/+
+/+
+/+
-/+
-/-
+/+
+/+
+/+
-/+
71
Chapter 11
Appendix
Responsibility for the Pay Service
(Cost to Customers)
― When the service is requested, in spite of in warranty, we may charge you for a visit from a service technician in the following cases.
Not a product defect
Cleaning of the product, Adjustment, Explanation, Re-installation and etc.
• If a service technician gives instructions on how to use product or simply adjusts options without disassembling product.
• If a defect is caused by external environmental factors (Internet, Antenna, Wired Signal, etc.)
• If a product is reinstalled or devices are connected additionally after installing the purchased product for the first time.
• If a product is reinstalled to move to a different spot or to move to a different house.
• If customer requests instructions on how to use because of another company's product.
• If customer requests instructions on how to use the network or another company's program.
• If customer requests software installation and setup for the product.
• If a service technician removes/cleans dusts or foreign materials inside of the product.
• If customer requests an installation additionally after purchasing a product through homeshopping or online.
A Product damage caused by customer's fault
Product damage caused by customer's mishandling or wrong repair
If a product damage is caused by;
• External impact or drop.
• Use of supplies or separatly sold product unspecified by Samsung.
• Repair from a person besides an engineer of outsourcing service company or partner of Samsung
Electronics Co., Ltd.
• Remodeling or repairing the product by customer.
• Using it with incorrect voltage or non-authorised electrical connections.
• Not following the "cautions" in User Manual.
Others
• If product fails by natural disaster. (lightning, fire, earthquake, flood damage, etc)
• If consumable components are all used up. (Battery, Toner, Fluorescent lights, Head, Vibrator,
Lamp, Filter, Ribbon, etc.)
― If customer requests a service in case the product has no defect, service fee may be charged. So please read User Manual first.
72
Correct Disposal
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
(For India Only)
This product is RoHS compliant.
For more information on safe disposal and recycling visit our website www.samsung.com/in or contact our Helpline numbers -
18002668282, 180030008282.
73
Terminology
OSD (On Screen Display)____ On screen display (OSD) allows you to customize on-screen settings to optimize the picture quality as required.
You can change the screen brightness, tint, size and many other settings using menus displayed on the screen.
Gamma____ The Gamma menu adjusts the grey scale that represents middle tones on the screen. Adjusting the brightness brightens the whole screen, but adjusting Gamma only brightens the medium brightness.
Grey scale____ Scale refers to levels of color intensity that show variations of color change from darker areas to brighter areas on the screen. Changes to the screen brightness are expressed with black and white variation, and grey scale refers to the medium area between black and white. Changing the grey scale through Gamma adjustment will change the medium brightness on the screen.
Scanning rate____ Scanning rate, or refresh rate, refers to the frequency of screen refreshes. Screen data is transmitted as it refreshes to display an image, although the refreshing is invisible to the naked eye. The number of screen refreshes is called scanning rate and is measured in Hz. A scanning rate of 60Hz means that the screen refreshes 60 times per second. The screen scanning rate depends on the performance of the graphics cards in your PC and monitor.
Dot Pitch____ The product and screen consist of red, green and blue dots.
A shorter distance between the dots produces a higher resolution. Dot pitch refers to the distance between the shortest distance between dots of the same color. Dot pitch is measured in millimeters.
Horizontal Frequency____ Characters or images displayed on the monitor screen consist of numerous dots (pixels).
Pixels are transmitted in horizontal lines, which are then arranged vertically to create an image. The horizontal frequency is measured in kHz and represents how many times horizontal lines per second are transmitted and displayed on the monitor screen. A horizontal frequency of 85 means that the horizontal lines that make up an image are transmitted 85000 times per second. The horizontal frequency is indicated in 85kHz.
Vertical Frequency____ One image is made of numerous horizontal lines. The vertical frequency is measured in Hz and represents how many images can be created per second by those horizontal lines. A vertical frequency of 60 means that an image is transmitted 60 times per second. The vertical frequency is also called "refresh rate" and affects screen flicker.
Resolution____ Resolution is the number of horizontal pixels and vertical pixels that form a screen. It represents the level of display detail. A higher resolution displays a greater amount of information on the screen and is suitable for performing multiple tasks at the same time.
E.g. A resolution of 1920 x 1080 consists of 1920 horizontal pixels (horizontal resolution) and 1080 vertical lines
(vertical resolution).
Plug & Play____ The Plug & Play feature allows the automatic exchange of information between a monitor and
PC to produce an optimum display environment.
The monitor uses VESA DDC
(international standard) to execute Plug
& Play.
74
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- 80 cm (31.5") LED VA
- Full HD 1920 x 1080 pixels 16:9
- 4 ms 350 cd/m² 5000:1
Related manuals
advertisement