SyncMaster 793MG

Install drivers Install programs

Notational

Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.

Prohibited

Do not disassemble

Do not touch

Important to read and understand at all times

Disconnect the plug from the outlet

Grounding to prevent an electric shock

Power

When not used for extended periods of time, set your computer to a screen saver. z

If the same image is present for long periods of time, Phosphor Burnt can be occured, or the screen may be blurred.

Do not use a damaged or loose plug. z

This may cause an electric shock or fire.

Do not pull the plug out by the wire nor touch the plug with wet hands. z

This may cause an electric shock or fire.

Use only a properly grounded plug and receptacle. z

An improper ground may cause electric shock or equipment damage.

Insert the power plug firmly so that it does not come loose. z

A bad connection may cause fire.

Do not excessively bend the plug and wire nor place heavy objects upon

them, which could cause damage. z

This may cause an electric shock or fire.

Do not connect too many extension cords or plugs to an outlet. z

This may cause fire.

Installation

Be sure to contact an authorized Service Center when installing your set in a location with heavy dust, high or low temperatures, high humidity, and chemical substances, or where it will be operated for 24 hours continuously such as an airport, train station or etc.

Failure to do so may cause serious damage to your set.

Put your monitor in a location with low humidity and a minimum of dust. z

Failure to do so may cause an electric shock or fire inside the monitor.

Do not drop the monitor when moving it. z

This may cause damage to the product or human body.

Install the monitor base in a showcase or shelf so that the end of the base does not protrude from the showcase or shelf. z

Dropping the product may cause damage to the product or personal injury.

Do not place the product on an unstable or small surface area. z

Place the product on an even, stable surface, as the product may fall and cause harm to someone walking by, specifically children.

Do not place the product on the floor. z Someone, specifically children could trip over it.

Keep any flammable objects such as candles, insecticides or cigarettes away from the product. z

Otherwise, this may cause a fire.

Keep any heating devices away from the power cable. z A melted coating may lead to electric shock or fire.

Do not install the product in places with poor ventilation, for instance, a bookshelf, closet, etc. z Any increase in internal temperature may cause fire.

Set down the monitor carefully. z The monitor could be damaged or broken.

Do not place the monitor face down. z The CDT surface may be damaged.

Do not use the monitor without the monitor stand. z z

It could break down or cause fire due to bad ventilation.

If the monitor must be used without the supplied stand, take steps to insure proper ventilation.

When installing the product, make sure to keep it away from the wall

(more than 10cm/4inch) for ventilation purposes. z

Poor ventilation may cause an increase in the internal temperature of the product, resulting in a shortened component life and degraded performance.

Clean

When cleaning the monitor case or the surface of the CDT, wipe with a slightly moistened, soft fabric.

Do not clean Flat monitor with water. Use a water-diluted mild detergent.

(Some detergents contain significant amounts of alcohol-based solvents, which can damage (color change) or crack the monitor case. The antiglare/anti-static surface coating on the CDT may also be affected.)

Dilute the detergent (1:10 ratio) with water before using.

Do not spray water or detergent directly on the monitor. z

This may cause damage, electric shock or fire.

Use the recommended detergent with a smooth cloth. z z

You may prevent the coated CDT from being damaged or the monitor cabinet from being dissolved, cracked or discolored.

You may buy a recommended detergent at any Service Center.

If the connector between the plug and the pin is dusty or dirty, clean it

properly with a dry cloth. z

A dirty connector may cause an electric shock or fire.

Make sure to unplug the power cord before cleaning the product. z

Otherwise, this may cause electric shock or fire.

Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth. z

Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent.

Contact the Service Center or Customer Center for interior cleaning once a year. z

Keep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause malfunction or fire.

Others

Do not remove cover(or back). z z

This may cause an electric shock or fire.

Refer servicing to qualified service personnel.

If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service . z

This may cause an electric shock or fire.

Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle. z z

This may cause malfunction, an electric shock or fire.

Especially avoid operating the monitor near water or outdoors where the monitor could be exposed to snow or rain.

If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact the Service Center . z The monitor may malfunction, causing an electric shock or fire.

Disconnect the plug from the outlet during storms or lightening or if it is

not used for a long period of time.

z

Failure to do so may cause an electric shock or fire.

Do not try to move the monitor by pulling only the wire or the signal cable. z

This may cause a breakdown, electric shock or fire due to damage to the cable.

Do not move the monitor right or left by pulling only the wire or the

signal cable. z This may cause a breakdown, electric shock or fire due to damage to the cable.

Do not cover the vents on the monitor cabinet. z Bad ventilation may cause a breakdown or fire.

Do not place water containers, chemical products or small metal objects on the monitor. z z

This may cause malfunction, an electric shock or fire.

If a foreign substance enters the monitor, unplug the power cord and contact the Service Center .

Do not place any heavy objects on the monitor. z This may cause an electric shock or fire.

Keep the product away from combustible chemical sprays or inflammable substances. z This may cause an explosion or fire.

Never insert anything metallic into the monitor openings. z

This may cause an electric shock, fire or injury.

Keep the monitor away from any magnetic substances. z This may cause discoloring or distortion of the image.

Watching the monitor continuously at a too close angle may result in

eyesight damage.

To ease eye strain, take at least a five-minute break after every hour of

using the monitor.

Do not install the product on an unstable, uneven surface or a location

prone to vibrations. z

Dropping the product may cause damage to the product or personal injury. Using the product in a location prone to vibrations may shorten the lifetime of the product or may catch fire.

When moving the monitor, turn off and unplug the power cord.

Make sure that all cables, including the antenna cable and cables connected to other devices, are disconnected before moving the monitor. z Failure to disconnect a cable may damage it and lead to fire or an electric shock.

Place the product out of children's reach, as they could damage it by

hanging onto it. z

A falling product could cause physical damage even death.

When not using the product for an extended time period, keep the

product unplugged z Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, leading to electric shock or fire.

Do not place children's favorite objects (or anything else that may be

tempting) on the product. z

Children may try to climb on the product to retrieve an object. The product could fall, causing physical damage or even death.

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer .

Contact a local dealer to buy optional items.

Unpacking

Monitor and Stand

(Some models include a stand attached.)

Manual

Cable

Quick Setup Guide

Warranty Card

(Not available in all locations)

User's Guide,

Monitor Driver,

Natural Color software,

MagicTune™ software

Power Cord

Stand

Stand

For Multimedia model (Option)

Manual

Cable

User Guide

Stand

Sound Cables(2each) DC Power Cord

Multimedia Speaker Stand

Front

Rear

Menu button [

Adjust buttons [

Enter button [ ]

] Opens the OSD menu. Also used to exit the OSD menu or return to the previous menu.

] These buttons allow you to highlight and adjust items in the menu.

Used to select the OSD menu.

Power button [ ] Use this button for turn the monitor on and off.

Power indicator This light glows green during normal operation, and blinks green once as the monitor saves your adjustments.

See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.

(The configuration at the back of the monitor may vary from product to product.)

Power port

Signal Cable

Connect the power cord for your monitor to the power port on the back of the monitor.

Connect the signal cable to the video port on your computer

(video board, video card, or graphics card).

See Connecting the Monitor for further information regarding cable connections.

Bottom

Tilt/Swivel Base You can separate the base from the monitor.

Connecting the Monitor

Setup-For Multimedia model | Multimedia Speaker Stand

1.

Connect the power cord for your monitor to the power port on the back of the monitor.

Plug the power cord for the monitor into a nearby outlet.

2-1.

Connecting to a computer

Connect the signal cable to the 15-pin, D-sub connector on the back of your computer.

2-2.

Connecting to a new Macintosh

Connect the monitor to the Macintosh computer using the D-SUB connection cable.

2-3.

Connecting to an old Macintosh

Connect your monitor to the Macintosh using the adapter for Macintosh (sold separately).

3.

Turn on your computer and monitor. If your monitor displays an image, installation is complete.

Setup-For Multimedia model

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

Turn off your computer and unplug the power cord.

Connect the end of the signal cable to your computer's video port(video board, video card or graphics card).

Connect one end of the other sound cable to the Mic Input jack on your sound card or computer.Connect the other end of this cable to the Mic By-pass jack on the back of the monitor stand.

Plug the DC power cord from the stand into a nearby outlet.

Connect the power cord for your monitor to the power port on the back of the monitor.

Plug the power cord for the monitor and the power cord for your computer into a nearby outlet.

Turn on your computer and monitor.

Turn up or down the On-Off control terminal on the stand of the monitor until it clicks.

Execute a sound program, music or sound effect in your computer and then adjust the volume by turning up or down until the sound volume is appropriate.

Adjust the treble and bass.

Sound distortion may occur when the monitor is placed on top of a mostly hollow cabinet such as your computer. If this occurs, place a pad or magazine beneath the monitor stand. High sound volume may also cause sound distortion; lower the volume.

Multimedia Speaker Stand

1.

Mic By-pass Jack

To transmit your voice,connect a sound cable from the Mic By-pass jack to the mic in jack on the sound card slot in your computer.

2.

Stereo Input Jack

Connect a sound cable from the input source(sound card,computer,CD-ROM drive).

3.

DC Power Cord

Connect DC power cord to monitor DC 12V output jack.

4.

Power Indicator

Glows green when the speakers are turned on.

5.

On/Off Volume

Turns On/Off and adjusts the output volume.

6.

Treble Control

Use to control high frequencies.

7.

Bass Control

Use to control low frequencies.

8.

Mic Input Jack

To transmit your voice,connect a microphone to this jack.

9.

Headphone Jack

To listen in privacy,connect headphones here.

10.

Detachable Stand Top

Base Installation

Tilt/Swivel Base | Attaching and Removing the Base

Tilt/Swivel Base

With the built-in pedestal, you can tilt and/or swivel the monitor for the most comfortable viewing angle.

The base is detachable.

Attaching and Removing the Base

If your monitor was supplied with the base detached, attach the base as follows.

Remove the twist-tie before attaching the base to the monitor.

Attaching the Base

1. Place the monitor upside-down on a flat work surface.

2. Align the tabs on the base with the corresponding slots on the bottom of the monitor.

3. Press the base onto the monitor until the tabs are fully engaged in the slots.

4. Push the base toward the front of the monitor until the release latch clicks into the locked position.

* Do not bend the snap.

Removing the Base

5. Squeeze and pull up on the release latch on the base.

6. Push the base toward the back of the monitor and lift up to remove the base.

The base will align with the monitor slots in only one position.

Installing the Monitor Driver(Automatic)

When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating

z system to another. Follow the directions appropriate for the operating system you

have.

Prepare a blank disk and download the driver program file at the Internet web site shown here.

Internet web site : http://www.samsung.com/ (Worldwide) http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China)

Windows ME

1. Insert CD into the CD-ROM drive.

2. Click "Windows ME Driver".

3. Choose your monitor model in the model list, then click the "OK" button.

4. Click the "Install" button in the "Warning" window.

5. Monitor driver installation is completed.

Windows XP/2000

1. Insert CD into the CD-ROM drive.

2. Click "Windows XP/2000 Driver"

3. Choose your monitor model in the model list, then click the "OK" button.

4. If you can see following message window, then click the "Continue Anyway" button.

Then click "OK" button.

This monitor driver is under certified MS logo and this installation doesn't damage your system. The certified driver will be posted on Samsung

Monitor homepage. http://www.samsung.com/ .

5. Monitor driver installation is completed.

Installing the Monitor Driver(Manual)

Windows XP | Windows 2000 | Windows Me | Windows NT | Linux z

When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you

have.

Prepare a blank disk and download the driver program file at the Internet web site shown here.

Internet web site : http://www.samsung.com/ (Worldwide) http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China)

Microsoft

®

Windows

®

XP Operating System

1. Insert CD into the CD-ROM driver.

2. Click "Start" —> "Control Panel" then click the "Appearance and Themes" icon.

3. Click "Display" icon and choose the "Settings" tab then click "Advanced..".

4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab.

5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button.

6. Select "Don't search ,I will.." then click "Next" and then click "Have disk".

7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button.

8. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button.

This monitor driver is under certified MS logo and this installation doesn't damage your system. The certified driver will be posted on Samsung

Monitor homepage. http://www.samsung.com/ .

9. Click the "Close" button, then click "OK" button continually.

10. Monitor driver installation is completed.

Microsoft

®

Windows

®

2000 Operating System

When you can see "Digital Signature Not Found" on your monitor, follow these steps.

1. Choose "OK" button on the "Insert disk" window.

2. Click the "Browse" button on the "File Needed" window.

3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.

How to install

1. Click "Start" , "Setting" , "Control Panel".

2. Double click the "Display" Icon.

3. Choose the "Settings" tab and then click "Advanced..".

4. Choose "Monitor".

Case1: If the "Properties" button is inactive, it means your monitor is properly configured.

Please stop installation

Case2: If the "Properties" button is active, click the "Properties" button then follow next steps continually.

5. Click "Driver" and then click on "Update Driver.." then click on the "Next" button.

6. Choose "Display a list of the known drivers for this device so that I can choose a

specific driver" then click "Next" and then click "Have disk".

7. Click the "Browse" button then choose A:(D:\Driver).

8. Click the "Open" button, then click "OK" button.

9. Choose your monitor model and click the "Next" button then click "Next" button.

10. Click the "Finish" button then the "Close" button.

If you can see the "Digital Signature Not Found" window then click the "Yes"button.

And click the "Finish" button then the "Close" button.

Microsoft

®

Windows

®

Millennium Operating System

1. Click "Start" , "Setting" , "Control Panel".

2. Double click "Display" icon.

3. Select the "Settings" tab and click "Advanced Properties" button.

4. Select the "Monitor" tab.

5. Click the "Change" button in the "Monitor Type" area.

6. Choose "Specify the location of the driver".

7. Choose "Display a list of all the driver in a specific location.." then click "Next" button.

8. Click the "Have Disk" button

9. Specify A:\(D:\driver) then click "OK" button.

10. Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK".

11. Continue choosing "Close" button and "OK" button until you close the Display Properties dialogue box.

Microsoft

®

Windows

®

NT Operating System

1. Click Start, Settings, Control Panel, and then double-click Display icon.

2. In Display Registration Information window, click Settings Tab and then click All Display

Modes.

3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK.

4. Click Apply button if you see the screen working normally after clicking Test. If the screen is not normal, change to a different mode (lower mode of resolution, colors or frequency).

If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by referring to the Preset Timing Modes in the user guide.

Linux Operating System

To execute X-Window, you need to make the X86Config file, which is a type of system setting file.

1. Press Enter at the first and the second screen after executing the X86Config file.

2. The third screen is for setting your mouse.

3. Set a mouse for your computer.

4. The next screen is for selecting a keyboard.

5. Set a Keyboard for your computer.

6. The next screen is for setting your monitor.

7. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.)

8. Set a vertical frequency for your monitor. (You can enter the frequency directly.)

9. Enter the model name of your monitor. This information will not affect the actual execution of X-Window.

10. You have finished setting up your monitor.

Execute X-Window after setting other requested hardware.

Natural Color

Natural Color Software Program

One of the recent problems in using a computer is that the color of the images printed out by a printer or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor.

The Natural Color S/W is the very solution for this problem. It is a color administration system developed by Samsung Electronics in association with Korea Electronics &

Telecommunications Research Institute (ETRI).

This system is available only for Samsung monitors and makes the color of the images on the monitor the same as the printed or scanned images.

For more information, refer to Help (F1) in the software program.

How to install the Natural Color software

Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial screen of the program Natural Color will be executed. Click Natural Color on the initial screen to install the Natural Color software.

To install the program manually, insert the CD included with the Samsung monitor into the CD-

ROM Drive, click the [Start] button of Windows and then select [Execute].

Enter D:\color\eng\setup.exe and then press the <Enter> key.

(If the drive where the CD is inserted is not D:\, enter the applicable drive.)

How to delete the Natural Color software program

Select [Setting]/[Control Panel] on the [Start] menu and then double-click [Add/Delete a

program].

Select Natural Color from the list and then click the [Add/Delete] button.

Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu.

These buttons allow you to highlight and adjust items in the menu.

Use to select the OSD menu.

Brightness

Menu Description

When OSD is not on the screen, push the button to adjust brightness.

Contrast

Menu Description

When OSD is not on the screen, push the button to adjust Contrast.

Menu Description

You can use the on-screen menus to change the brightness according to personal preference.

Direct Access Feature : When OSD is not on the screen, push the button to adjust brightness.

You can use the on-screen menus to change the contrast according to personal preference.

A "Moiré" pattern can appear on your screen, looking like a series of concentric circles or arcs. To eliminate this pattern, use the horizontal moire adjustments.

A "Moiré" pattern can appear on your screen, looking like a series of concentric circles or arcs. To eliminate this pattern, use the vertical moire adjustments.

The Degauss feature will remove color impurities caused by magnetic fields.

Use the recall feature to reset these monitor settings to their original levels: Position, Size, Pincushion, Trapezoid,

Parallelogram, Pinbalance, Rotation, H-Moire,and V-Moire.

Note: If you have selected "Yes", all settings listed above will be reset. All other settings will remain the same.

Play/Stop

Menu Description

Color temperature is a measure of the 'warmth' of the image colors. (6500K / 9300K)

Use to adjust the monitor color setting.(Red)

Play/Stop

Use to adjust the monitor color setting.(Green)

Use to adjust the monitor color setting.(Blue)

Standard Red Green Blue (sRGB) is a defined default color space. If a monitor, printer and scanner are all calibrated to the sRGB color characteristics, then you can find color matching from each peripheral.

Note : When the monitor is in the sRGB mode, Brightness /

Contrast adjustment is not available.

Menu Description

Follow these instructions to change the horizontal position of the monitor's entire display.

Play/Stop

Follow these instructions to change the vetical position of the

monitor's entire display.

Follow these instructions to change the horizontal size of the monitor's entire display.

Follow these instructions to change the vertical size of the monitor's entire display.

Adjust the pincushion setting when the sides of the display are bowed in or bowed out.

Adjust the pinbalance setting when the sides of the display are bowed towards the left or right.

Adjust the trapezoid setting when the top or bottom of the display is too large or small.

Adjust the parallelogram setting when the display is leaning left or right.

Adjust the rotation setting when the entire display is tilted left or right.

Provides information about the display timing and sync signals polarity(user mode).

Note: These screens do not allow any changes to the settings, they are for information only.

Overview | Installation | OSD Mode | | Uninstall | Troubleshooting

Overview

What is MagicTune™?

Monitor performance can vary due to the graphics card, host computer lighting conditions and other environmental factors. In order to get the best image on a monitor requires you to adjust it for your unique setting. Unfortunately, the manual controls available to tune the image often prove to be challenging. Proper adjustment (tuning) requires an easy to use program that goes through a step-by-step process to obtain the best overall picture quality.

In most cases even simple adjustments to Brightness, or Contrast require navigation of the multi-level, on-screen display (OSD) menus that are not easy to understand. Furthermore, there is no feedback to assist in correctly setting the controls of the monitor. MagicTune™ is a software utility that guides you through the tuning process with easy to understand instructions and back ground patterns designed for each monitor control. The display settings for each user can be saved, providing an easy way to select display characteristics in a multi-user environme or having a single user have multiple defined presets based on content and ambient lighting.

Basic Functionality

MagicTune™ is a software utility that allows monitor adjustment and color tuning using the Display Data

Channel Command Interface (DDC/CI) protocol. All adjustments to the display are controlled via software to eliminate the need to use the monitor on-screen display (OSD).

MagicTune™ supports Windows™ 98 SE, Me, 2000, XP Home, and XP Professional.

It is recommended using MagicTune™ in Windows™ 2000 or later.

MagicTune™ allows for quick accurate tuning of the display with the ability to easily save and use monitor configurations that are best suited for you.

OSD Mode

The OSD mode allows easy adjustment of monitor settings without taking pre-defined steps. You can access the desired menu item to set with ease.

Overview | Installation | OSD Mode | | Uninstall | Troubleshooting

Installation

1. Insert the installation CD into the CD-ROM drive.

2. Click the MagicTune™ installation file.

3. Select installation Language, Click "Next".

4. When the Installation Shield Wizard window appears, click "Next."

5. Select "I agree to the terms of the license agreement" to accept the terms of use.

6. Choose a folder to install the MagicTune™ program.

7. Click "Install."

8. The "Installation Status" window appears.

9. Click "Finish."

10. When the installation is complete, the MagicTune™ executable icon appears on your desktop.

Double-click the icon to start the program.

MagicTune™ execution icon may not appear depending on specification of computer system or monitor. If that happens, press F5 Key.

Installation Problems

The installation of MagicTune™ can be affected by such factors as the video card, motherboard and the network environment.

See "Troubleshooting" if you have trouble during installation.

System Requirements

OS z z z z z

Windows™ 98 SE

Windows™ Me

Windows™ 2000

Windows™ XP Home Edition

Windows™ XP Professional

It is recommended using MagicTune™ in Windows™ 2000 or

later.

Hardware z z

32MB Memory above

25MB Hard disk space above

* For more information, visit the MagicTune™ website .

Overview | Installation | OSD Mode | Uninstall | Troubleshooting

MagicTune allows for quick accurate tuning of the display with the ability to easily save and use monitor configurations that are best suited for you. z z

OSD mode may appear inconsistent with the explanation in guidance book depending on specification of each monitor.

MagicTune control mode will be different according to monitor models.

OSD Mode

The OSD mode makes the adjustment of settings on all monitors easy. When selected , each tab on top of the control window displays the general descriptions of the sub-menu items for adjustment.

When selected, each tab displays a list of menus. For quick adjustment of the monitor settings, the OSD mode allows easy and convenient access to all tabs and sub-menu items.

Button Tab Definition

OK

Reset

Cancel

Applies any changes made and exits MagicTune.

Restores the display settings to the factory settings.

Exits MagicTune without applying the changes made. If you have not made any changes in the control window, clicking "Cancel" does not cause any actions.

Picture Tab Definition

Allows the user to adjust the screen settings to the desired values.

Brightness

Contrast

MagicBright™

Makes the entire screen brighter or darker. The detailed data of the images in the dark areas can be lost if the brightness is not adjusted to the proper level. Adjust the brightness for best viewing conditions.

Adjusts the difference in brightness between the bright and dark areas on screen.

Determines the crispness of the images.

MagicBright™ is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available:

Text, Internet,Game, Sport, Movie and Custom. Each mode has its own pre-configured brightness value. You can easily select one of six settings by simply pressing MagicBright control buttons. z

19" or above

1. Text: For documentations or works involving heavy text.

2. Internet: For working with a mixture of images such as text and graphics.

3. Game: For watching motion pictures such as a Game.

4. Entertain: For watching motion pictures such as a DVD or VCD.

z

Less than 19"

1. Text: For documentations or works involving heavy text.

2. Internet: For working with a mixture of images such as text and graphics.

3. Entertain: For watching motion pictures such as a DVD or VCD.

Color Tab Definition

Adjusts the "warmth" of the monitor background or image color.

The tone of the color can be changed.

Color Tone

Color Control z z

5000K - 6500K - 9300K

Reset

Adjusts of the monitor image color.

You can change the monitor color to your desired color. z z

R- G - B sRGB

Image Tab Definition

Adjusts the Position, Size and Rotation values.

Geometry 1

Geometry 2

Other

Adjusts the Position, Size and Rotation values. z z z

Position

Size

Rotation

Adjusts the Pincushion, Pinbalance, Trapezoid and Parallelogram values. z z z z

Pincushion

Pinbalance

Trapezoid

Parallelogram

Adjusts the Moire, Degauss, Sidepin Corner, and Pinbalance Corner values. z z z z z z

Moire

Degauss

Sidepin Corner Top

Sidepin Corner Bottom

Pinbalance Corner Top

Pinbalance Corner Bottom

Option Tab Definition

You can configure MagicTune using the following options.

Preferences

Loads the Preferences Dialog Box. Preferences in use will have an "V" in the check box. To turn on or off any Preference, position the cursor over the box and click. z z

Enable task tray menu .

- To access the MagicTune menus, click the icon on the [task tray menu].

The menus are not displayed if the [Enable System Tray] is deselected in

[Options] ' [Basic Settings].

Select Language - The language chosen affects only the language of the OSD.

Support Tab Definition

Shows the Asset ID and the version number of the program, and allows you to use the Help feature.

Help

Asset ID

Version

Visit the MagicTune website or click to open the Help files (User Manual) if you need any help installing or running MagicTune. The User Manual opens within a basic browser window. you can use the server to control the Client monitor.

(Server program should be installed to use this program as Client)

User Name

User ID

Shows the user name that is registered in PC.

Shows the user ID that is register in PC.

Server IP Write down the server IP .

Department Write down the department.

Location Write down the location.

Displays the version of MagicTune.

Overview | Installation | OSD Mode | | Uninstall | Troubleshooting

Uninstall

The MagicTune™ program can be removed only by using the "Add or Remove Programs" option of the

Windows™ Control Panel.

Perform the following steps remove MagicTune™.

1. Go to [Task Tray] ' [Start] ' [Settings] and select [Control Panel] in the menu. If the program runs on

Windows™ XP, go to [Control Panel] in the [Start] menu.

2. Click the "Add or Remove Programs" icon in Control Panel.

3. In the "Add or Remove Programs" screen, scroll down to find "MagicTune™." Click on it to highlight it.

4. Click the "Change/Remove" button to remove the program.

5. Click "Yes" to begin the uninstall process.

6. Wait until the "Uninstall Complete" dialog box appears.

Visit the MagicTune™ website for technical support for MagicTune™, FAQs (questions and answers) and software upgrades.

Overview | Installation | OSD Mode | | Uninstall | Troubleshooting

Troubleshooting

The current computing system is not compatible with MagicTune™.

Please press OK and click on the "Shortcut to the MagicTune™ site" to view our home

page for further reference.

An error may occur when your video/graphic card is not in the 'Available' list.

(The latest or oldest video cards may not be compatible.)

Please visit our homepage to see the Troubleshooting section.

An error may occur if the card maker has modified the video card driver or the graphics chip even when the video card is in the list.

Please visit our homepage to see the Troubleshooting section.

Check if your monitor is manufactured by Samsung.

Products from other manufacturers may cause errors.

Only Samsung products are able to support this feature.

An error may occur even when your monitor is manufactured by Samsung but is out of date.

Check if your monitor is able to support MagicTune™.

This feature is only supported by those monitors that are registered on our homepage.

Check for the monitor before purchasing it as out-of-date models are not supported.

An error occurs when no information on EDID (Extended Display Identification

Data) exists for the current monitor.

This happens when from your desktop, Start > Setup > Control Panel > System >

Hardware > Device Manager > Monitor is selected, the current "Plug-and-play monitor" is removed and new hardware is searched for but the system couldn't find any "Plug-and-play monitor".

Please visit our homepage to see the Troubleshooting section.

An error occurs when replacing the monitor with a new one when the system power is off but the system has not been restarted.

Please restart the system each time the monitor is replaced before using

MagicTune™.

An error occurs when the video card driver is not installed properly.

This happens when the current video card list is not displayed normally. You can check this via Start > Setup > System > Hardware > Device Manager > Display

Adapter.

Visit the video card maker's homepage and download and install the latest driver.

For more information about the video card, contact the card manufacturer.

To ensure normal operation, please restart your system.

An error occurs when the system is not restarted after installing MagicTune™.

(This is for Win98SE and WinMe only.)

Restart the system before use.

For the best performance of MagicTune™, adjust to the optimal resolution. Refer to the

User Guide for the optimal resolution.

If you do not adjust to the optimal resolution and perform Color Calibration, the monitor cannot be adjusted to the optimal condition.

Refer to the manual for the optimal resolution.

This video card does not support MagicTune™.

Please install a new video card driver.

An error occurs when the video card driver is not installed properly.

This happens when the current video card list is not displayed normally. You can check this from Start > Setup > System > Hardware > Device Manager > Display

Adapter.

Visit the video card manufacturer's homepage and download and install the latest driver.

For more information about the video card, contact the card manufacturer.

As the Highlight program uses the communication lines,

please exit the Highlight program before you can access MagicTune™.

Some of Samsung CDT monitors support the Highlight feature.

When using both the Highlight feature and MagicTune™ simultaneously, conflicts occur, which cause errors.

Make sure to turn OFF Highlight before using MagicTune™.

Troubleshooting

z

MagicTune™ may not work in case monitor is replaced or driver of graphic card is updated while

MagicTune™ is operating. If so, please restart the system.

Symptom Check List Solutions

Check when

MagicTune™ does not function properly.

MagicTune™ feature is found only on PC (VGA) with Window OS that supports Plug and Play.

* To check whether your PC is available for

MagicTune™ feature, follow the

steps below (When Windows™ is XP);

Control Panel -> Performance and Maintenance

-> System -> Hardware -> Device Manager ->

Monitors -> After deleting Plug and Play monitor, find 'Plug and Play monitor' by searching new Hardware.

MagicTune™ is an additional software for the monitor. Some graphic cards may not support your monitor. When you have a problem with

MagicTune™ doesn't work properly.

the graphic card, visit our website to check the compatible graphic card list provided. http://www.samsung.com/monitor/magicTune .

Have you changed your PC or video graphic card?

Download the latest program. The program can be downloaded http://www.samsung.com/monitor/magicTune .

z z

Visit the MagicTune™ website for technical support for MagicTune™, FAQs (questions and answers) and software upgrades.

Visit the MagicTune™ website and download the installation software for MagicTune™ MAC.

Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the

Information section or contact your dealer .

Symptom

No images on the screen. I cannot turn on the monitor.

Check List

Is the power cord connected properly?

Can you see " the screen?

" on

Solutions

Check the power cord connection and supply.

Check the signal cable connection.

If the power is on, reboot the computer to see the initial screen(the login screen), which can be seen.

If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows

ME/XP/2000) and then change the frequency of the video card.

(Refer to the Preset Timing Modes )

Can you see " the screen?

" on

Note: If the initial screen (the login screen) does not appear, contact a service center or your dealer .

You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can properly handle.

Adjust the maximum resolution and frequency that the monitor can handle properly.

There is no image on the screen.

Is the power indicator on the monitor blinking at 1 second intervals?

The monitor is in PowerSaver mode.

Press any key on the keyboard to activate the monitor and restore the image on the screen.

The image on the screen is shaking.

Check the monitor configuration to see if it is in Interlace Mode.

(Interlace Mode: Vertical frequency 43Hz, 87Hz(i), etc)

Change the vertical frequency to Non-

Interlace mode by referring to the video card manual.

Are there any magnetic products such as a power adapter, speaker or a

Move the monitor away from anything that can create a strong magnetic field.

high voltage wire near by?

Is the voltage stable?

The screen image can appear to shake or vibrate at a particular time of day due to low supply voltage.

The screen image can also appear to shake or vibrate if there is a problem with the video card or the computer's main board.

The screen shows strange colors or just black and white.

The screen suddenly has become unbalanced.

Is the screen displaying only one color as if looking at the screen through a cellophane paper?

Has the video card been set properly?

Have you changed the video card or the driver?

Check the signal cable connection.

Make sure the video card is fully inserted in it's slot.

Have the screen colors become strange after running a program or due to a crash between applications?

Reboot the computer.

Set the video card by referring to the video card manual.

Adjust screen image position and size using the OSD.

The screen is out of focus or OSD cannot be adjusted.

The screen is partially distorted.

Have you adjusted the resolution or frequency on the monitor?

Adjust the resolution and frequency of the video card.

(Refer to the Preset Timing Modes ).

The screen can be unbalanced due to the cycle of the video card signals. Readjust Position by referring to the OSD.

Have you adjusted the resolution or frequency on the monitor?

Are there any magnetic products such as an adapter, speaker or a high voltage wire near the monitor?

Adjust the resolution and frequency of the video card.

(Refer to the Preset Timing Modes ).

Enter the OSD and perform a "Degauss".

Keep the monitor away from any magnetic products.

LED is blinking but no images on the screen.

There are only 16 colors shown on the screen.

The screen colors have changed after changing the video card.

There is a message that reads "Unrecognized monitor, Plug & Play

(VESA DDC) monitor found".

Check when MagicTune does not function properly.

Is the frequency properly adjusted when checking the Display Timing on the menu?

Adjust the frequency properly by referring to the video card manual and the Preset Timing

Modes .

(The maximum frequency per resolution may differ from product to product.)

Have the Windows colors been set properly?

Windows ME/2000/XP:

Set the colors properly at the Control Panel

→ Display → Settings.

Has the video card been set properly?

Set the video card by referring to the video card manual.

Have you installed the monitor driver?

Install the monitor driver according to the

Driver Installation Instructions .

See the video card manual to see if the Plug

& Play (VESA DDC) function can be supported.

Install the monitor driver according to the

Driver Installation Instructions .

MagicTune feature is found only on PC (VGA) with Window OS that supports Plug and Play.

* To check whether your PC is available for

MagicTune feature, follow the

steps below (When Windows is XP);

Control Panel → Performance and

Maintenance → System → Hardware →

Device Manager → Monitors → After

deleting Plug and Play monitor, find 'Plug and Play monitor' by searching new

Hardware.

MagicTune is an additional software for the monitor. Some graphic cards may not support your monitor. When you have a problem with the graphic card, visit our website to check the compatible graphic card list provided. http://www.samsung.com/monitor/magictune

MagicTune™ doesn't work properly.

Have you changed your

PC or video graphic card?

Download the latest program. The program can be downloaded http://www.samsung.com/monitor/magictune .

Visit the MagicTune™ website and download the installation software for MagicTune™

MAC.

Check the following items if there is trouble with the monitor.

1. Check if the power cord and the video cables are properly connected to the computer.

2. Check if the computer beeps more than 3 times when booting.

(If it does, request an after-service for the main board of the computer.)

3. If you installed a new video card or if you assembled the PC, check if the installed adapter (video) driver and the monitor driver.

4. Check if the scanning ratio of the video screen is set at 50Hz ~ 160 Hz.

(Do not exceed 60 Hz when using the maximum resolution.)

5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "Control Panel→System→Device Administrator" and then reboot the computer to reinstall the adapter (video) driver.

If problems repeatedly occur, contact an authorized service center .

Q & A

Question

How can I change the frequency?

How can I adjust the resolution?

Answer

Frequency can be changed by reconfiguring the video card.

Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.)

Windows ME/XP/2000 : Set the resolution at the Control

Panel→Display→Settings.

* Contact the video card manufacturer for details.

How can I set the Power Saving function?

Windows ME/XP/2000 : Set the function at BIOS-SETUP of the computer or the screen saver. (Refer to

Windows/Computer Manual).

The monitor makes a sound when it is turned on.

This is normal as some sound may be generated when the metal case and the electromagnet, which are installed to block any electromagnetic waves, interact with each other.

How can I clean the outer case/Picture tube?

Disconnect the power cord and then clean the monitor with a soft cloth, using either a cleaning solution or plain water.

Do not leave any remains of the detergent nor scratch the case. Do not allow any water to go inside the monitor.

Self-Test Feature Check

Self-Test Feature Check | Warning Messages | Environment | Useful Tips

Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly.

Self-Test Feature Check

1. Turn off both your computer and the monitor.

2. Unplug the video cable from the back of the computer.

3. Turn on the monitor.

If the monitor is functioning properly, you will see a box in the illustration below.

This box appears during normal operation if the video cable becomes disconnected or damaged.

4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor.

If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly.

Warning Messages

If there is something wrong with the input signal, the message below appears on the screen or the screen goes blank although the power indicator LED is still on. The message may indicate that the monitor is out of scan range or that you need to check the signal cable.

Environment

The location and the position of the monitor may influence the quality and other features of the monitor.

1. If there are any sub woofer speakers near the monitor, unplug and relocate the woofer to another room.

2. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor.

3. Degauss the monitor if any devices were removed from the area.

Useful Tips z

A monitor recreates visual signals received from the computer. Therefore, if there is trouble with the computer or the video card, this can cause the monitor to become blank, have poor coloring, noise, unavailable video mode, etc. In this case, first check the source of the problem, and then contact a service center or your dealer.

z

Judging the monitor's working condition

If there is no image on the screen or a " " message comes up, disconnect the cable from the computer while the monitor is still powered on.

{

If there is a message coming up on the screen or if the screen goes white, this means the monitor is in working condition.

{ In this case, check the computer for trouble.

General

General

Model Name

Picture Tube

Type

Deflection angle

Dot Pitch

Screen type

SyncMaster 793MG

17" (43 cm) DynaFlat (40.6 cm viewable)

90 °

0.20 mm (Horizontal)

Aluminized tri-color phosphor dot trio with black matrix.

Anti-doming invar shadow mask.

Multi-layer coated with anti-static.

Resolution

Optimum resolution

Maximum resolution

Active Display

Horizontal

Vertical

Synchronization

Horizontal

Vertical

1024 x 768 @ 85 Hz

1280 x 1024 @ 60 Hz

312 ± 4 mm

234 ± 4 mm

30 ~ 70 kHz

50 ~ 160 Hz

Input Signal Definition

Video Signal

Sync Signal

Display Color

Unlimited

RGB, Analog 0.7 Vp-p Positive at 75 Ω

Separate H/V sync, TTL level, positive or negative

Maximum Pixel Clock

120 MHz

Power Supply

90 ~ 264 VAC rms, 60/50 Hz ± 3Hz

Power Consumption

66 W (nominal)

Dimensions (WxDxH)

401 x 410 x 378 mm / 15.8 x 16.1 x 14.9 inch (After installation of Stand)

Weight

14.3 kg

Environmental considerations

Operating Temperature 32°F ~ 104°F(0°C ~ 40°C)

Humidity 10% ~ 80%, non-condensing

Storage Temperature -4°F ~113°F (-20°C ~ 45°C)

Humidity 5% ~ 95%, non-condensing

Plug and Play Capability

This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings.

Note: Design and specifications are subject to change without prior notice.

PowerSaver

This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use a software utility installed on your computer to set up this feature.

State Normal Operation Power-off mode

Power Indicator

Power Consumption

Green

66 W (nominal)

Green, Blinking

Less than 1 W

Preset Timing Modes

If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows.

Display Mode

VESA, 640 x 480

VESA, 800 x 600

VESA, 1024 x 768

Horizontal

Frequency

(kHz)

37.500

53.700

68.700

Vertical

Frequency

(Hz)

75.000

85.100

85.000

Pixel Clock

(MHz)

31.500

56.250

94.500

Sync Polarity

(H/V)

-/-

+/+

+/+

Horizontal Frequency

The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz

Vertical Frequency

Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called Vertical Frequency or Refresh

Rate. Unit: Hz

Contact SAMSUNG WORLD-WIDE

If you have any questions or comments relating to Samsung products, please

contact the SAMSUNG customer care center.

North America

CANADA 1-800-SAMSUNG (7267864) http://www.samsung.com/ca

MEXICO

U.S.A

01-800-SAMSUNG (7267864)

1-800-SAMSUNG (7267864) http://www.samsung.com/mx http://www.samsung.com

ARGENTINE

BRAZIL

Latin America

0800-333-3733

0800-124-421 http://www.samsung.com/ar http://www.samsung.com/br

CHILE

COSTA RICA

ECUADOR

EL SALVADOR

GUATEMALA

JAMAICA

PANAMA

PUERTO RICO

REP. DOMINICA

TRINIDAD & TOBAGO

VENEZUELA

800-726-7864 (SAMSUNG)

0-800-507-7267

1-800-10-7267

800-6225

1-800-299-0013

1-800-234-7267

800-7267

1-800-682-3180

1-800-751-2676

1-800-7267-864

1-800-100-5303 http://www.samsung.com/cl http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin

Europe

BELGIUM 02 201 2418 http://www.samsung.com/be

RUSSIA

UKRAINE

AUSTRALIA

CHINA

HONG KONG

INDIA

INDONESIA

JAPAN

MALAYSIA

PHILIPPINES

SINGAPORE

THAILAND

TAIWAN

VIETNAM

SOUTH AFRICA

U.A.E

CZECH REPUBLIC

DENMARK

FINLAND

FRANCE

GERMANY

HUNGARY

ITALIA

LUXEMBURG

NETHERLANDS

NORWAY

POLAND

PORTUGAL

SLOVAKIA

SPAIN

SWEDEN

U.K

844 000 844

38 322 887

09 693 79 554

08 25 08 65 65 (€ 0,15/min)

01805 - 121213 (€ 0,12/Min)

06 40 985 985

199 153 153

02 261 03 710

0900 20 200 88 (€ 0.10/Min)

231 627 22

0 801 801 881

80 8 200 128

0850 123 989

902 10 11 30

08 585 367 87

0870 242 0303

8-800-200-0400

8-800-502-0000

CIS http://www.samsung.com/cz http://www.samsung.com/dk http://www.samsung.com/fi http://www.samsung.com/fr http://www.samsung.de

http://www.samsung.com/hu http://www.samsung.com/it http://www.samsung.lu

http://www.samsung.com/nl http://www.samsung.com/no http://www.samsung.com/pl http://www.samsung.com/pt http://www.samsung.com/sk http://www.samsung.com/es http://www.samsung.com/se http://www.samsung.com/uk http://www.samsung.ru

http://www.samsung.com/ur

1300 362 603

Asia Pacific

800-810-5858, 010- 6475 1880

2862 6001

3030 8282, 1600 1100 11

0800-112-8888

0120-327-527

1800-88-9999

1800-10-SAMSUNG (7267864)

1800-SAMSUNG (7267864)

1800-29-3232, 02-689-3232

0800-329-999

1 800 588 889 http://www.samsung.com/au http://www.samsung.com.cn

http://www.samsung.com/hk http://www.samsung.com/in http://www.samsung.com/id http://www.samsung.com/jp http://www.samsung.com/my http://www.samsung.com/ph http://www.samsung.com/sg http://www.samsung.com/th http://www.samsung.com/tw http://www.samsung.com/vn

Middle East & Africa

0860 7267864 (SAMSUNG)

800SAMSUNG (7267864) http://www.samsung.com/za http://www.samsung.com/mea

Terms

Dot Pitch

The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot

Pitch'. Unit: mm

Vertical Frequency

The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called Vertical Frequency or

Refresh Rate. Unit: Hz

Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz.

Horizontal Frequency

The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal

Frequency. Unit: kHz

Interlace and Non-Interlace Methods

Showing the horizontal lines of the screen from the top to the bottom in order is called the

Non-Interlace method while showing odd lines and then even lines in turn is called the

Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs.

Plug & Play

This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically. This monitor follows the international standard VESA DDC for the Plug & Play function.

Resolution

The number of horizontal and vertical dots used to compose the screen image is called

'resolution'. This number shows the accuracy of the display. High resolution is good for performing multiple tasks as more image information can be shown on the screen.

Example: If the resolution is 1024 X 768, this means the screen is composed of 1024 horizontal dots (horizontal resolution) and 768 vertical lines (vertical resolution).

MagicGreen

The MagicGreen CDT monitor has adopted a Well-Being CDT that is coated with a Vital &

Pure coating, which radiates far infrared and anion and provides antibacterial and deodorizing effects.

z z

Vital Coating Radiates far infrared and anion by applying a specialized ceramic on the surface of the CDT funnel.

Pure Coating Provides antibacterial deodorizing effects by treating the surface with photocatalyst TiO2 and Nano Silver.

Authority

Information in this document is subject to change without notice.

© 2006 Samsung Electronics Co., Ltd. All rights reserved.

Reproduction in any manner whatsoever without the written permission of Samsung Electronics

Co., Ltd. is strictly forbidden.

Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.

Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and

Windows NT are registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are registered trademarks of Video Electronics Standard Association; the E NERGY S TAR ® name and logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). All other product names mentioned herein may be the trademarks or registered trademarks of their respective owners.

Class B

This device is a Class B digital apparatus. For Safety and EMC compliance guide, you may refer to

"Regulatory" Guide.

.

MÉXICO

IMPORTADO POR: SAMSUNG ELECTRONICS MÉXICO. S.A. de C.V.

Vía Lopez Portillo No. 6, Col. San Fco. Chilpan

Tultitlán, Estado de México, C.P. 54940

Tel: 01-55-5747-5100 / 01-800-726-7864

EXPORTADO POR: Samsung Electronics CO.,LTD.

416, Mae tan-3dong, Yeongtong - gu,

Suwon City, Gyeonggi-do Korea

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment) - Europe only

(Applicable in the European Union and other European countries with

separate collection systems)

This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.