advertisement
DVD-P728 TWN(gb)00049T-1 7/23/02 1:25 PM Page 2
Precautions
1. Setting up
Ensure that the mains supply in your house complies with that indicated on the identification sticker located at the back of your play. Install your player horizontally, on a suitable base (furniture), with enough space around it for ventilation (7~10cm). Make sure the ventilation slots are not covered.
Do not stack other, or heavy devices on top of the player. Do not place the player on amplifiers or other equipment which may become hot. Before moving the player ensure the disc tray is empty.
This player is designed for continuous use. Switching off the DVD player to the stand-by mode does not disconnect the electricity supply In order to separate the player completely from the mains,it has to be disconnected by unplugging the main plug, especially when left unused for a long period of time.
2. Caution
Protect the player from moisture (dripping or splashing and objects filled with liquids), and excess heat
(e.g.fireplace) or equipment creating strong magnetic or electric fields (i.e.speakers...). Disconnect the power cable from the mains electricity supply if the player malfunctions. Your player is not intended for industrial use but for domestic purposes only. Use of this product is for personal use only. If your player or disc has been stored in a cold atmosphere for example during transportation in the winter, wait for approximately 2 hours until they have reached room temperature, before use.
3. For your safety
Never open the player or any of its components. It can be dangerous for you or certain fragile components.
You could receive an electric shock or touch the laser beam. Do not place your eyes close to the opening of the disc tray or any other opening to look inside the player.
4. Disc
Be careful handle your discs with care. Hold a disc with finger on the border or hole. Always place disc with the label facing upward (in case of a single side disc ). Always use a soft cloth to clean disc if necessary, wipe from the centre to the border. Always put disc back into their cases after playing and store in vertical position. Always place the disc properly into the tray using the proper guide area. Never use record cleaning sprays, benzine, static electricity liquids or any other solvent, if the disc surface is dirty.
Wipe gently with a soft damp (water only) cloth, never wipe the disc in a circular motion, since circular scratches are likely to occur and could cause noise during playback.
5. Battery
The battery used in this product contains chemicals that are harmful to the environment.
Do not dispose of batteries in the general household waster. It is recommended that the replacement of the battery should be done by a technician.
6. Maintenance of cabinet
For safety reasons, be sure to disconnect the AC power cord from the AC outlet.
• Do not use benzene, thinner, or other solvents for cleaning.
• Wipe the cabinet with a soft cloth.
2
1
2
4
JOG
/SHUTTLE
G/SH UTTLE
JOG E
3
5
Precautions
JOG
/SHUTTLE
JOG
/SHUTTL
3
DVD-P728 TWN(gb)00049T-1 7/23/02 1:25 PM Page 4
Before You Start
Accessories
Remote Control Easy Remote Control
Batteries for
Remote Controls (AA Size)
4
User’s Manual Video/Audio Cable
Install Batteries in the
Remote
1 Open the battery cover on the back of the remote.
Insert two AA batteries. Make sure that the polarities (+ and -) are aligned correctly.
Replace the battery cover.
If remote doesn’t operate properly:
• Check the polarity + - of the batteries
(Dry-Cell)
• Check if the batteries are drained.
• Check if remote sensor is blocked by obstacles.
• Check if there is any fluorescent lighting nearby.
TABLE OF CONTENTS
General Features ............................................................................................ 6
Disc Type and Characteristics .......................................................................... 7
Description-Front Panel ....................................................................................8
Description-Rear Panel ....................................................................................9
Tour of the Remote Control..............................................................................10
Choosing a Connection ..................................................................................12
Playing a Disc................................................................................................14
Using the Search & Skip Functions ............................................................16
Using the Display Function..............................................................................17
Repeat Play ..................................................................................................18
Program Play & Random Play ........................................................................19
S.FIT Play ......................................................................................................20
Digest Play ....................................................................................................21
Using the Disc View Function ..........................................................................22
Selecting the Audio Language ........................................................................23
Selecting the Subtitle Language ......................................................................24
Changing the Camera Angle ..........................................................................25
Using the Instant Replay Function ....................................................................26
Using the Bookmark Function..........................................................................27
Using the Zoom & 3D Sound Functions ..........................................................28
MP3 Play ......................................................................................................29
Using the Setup Menu ....................................................................................31
Setting Up the Language Features ..................................................................32
Setting Up the Parental Control ......................................................................34
Setting Up the Audio ....................................................................................35
Surround Sound Speaker Setup ......................................................................36
Setting Up the Display ....................................................................................37
Controlling a TV with the Remote ....................................................................38
Troubleshooting..............................................................................................39
Specifications ................................................................................................40
5
DVD-P728 TWN(gb)00049T-1 7/23/02 1:25 PM Page 6
General Features
Excellent Sound
Dolby Digital, a technology developed by Dolby Laboratories provides crystal clear sound reproduction.
Repeat
You can repeat a song or movie simply by pressing the REPEAT button.
Screen
Both regular and widescreen(16:9) pictures can be viewed.
MP3
This unit can play discs created from MP3 files.
Instant Replay
This function is used to replay the previous 10 seconds of the movie from the current position.
Slow Motion
An important scene can be viewed in slow motion.
Programmed Play
You can program tracks to play in desired order.
Progressive Scan
Progressive scanning creates an improved picture with double the scan lines of a conventional interlaced picture.
Parental Control
The parental control allows users to set the level necessary to prohibit children from viewing harmful movies such as those with violence, adult subject matter, etc.
Easy Remocon
The Easy Remocon combines frequently used functions for easier operation.
NOTE
Various On-Screen Menu Functions
You can select various languages(Audio/Subtitle) and screen angles while enjoying movies.
* Discs which cannot be played with this player:
• DVD-ROM
• CD-ROM
• DVD-RAM
• CDV
• CDI • SVCD, CVD
• HD layer of super Audio CD
• CDGs play audio only, not graphics.
* Ability to play back may depend on recording conditions:
• DVD-R
• DVD+RW, -RW
• CD-RW
COPY PROTECTION
• Many DVD discs are encoded with copy protection. Because of this, you should only connect your DVD player directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copy-protected DVD discs.
• This product incorporates copyright protection technology that is protected by methods claims of certain U.S.
patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
6
Disc Type and Characteristics
This DVD player is capable of playing the following types of discs with the corresponding logos:
Disc Types
(Logos)
DVD
Recording
Types
Audio
+
Video
Disc Size
12cm
8cm
Max.
Playing Time
Single-sided
240 min.
Double-sided
480 min.
Single-sided
80 min.
Double-sided
160 min.
Characteristics
• DVD contains excellent sound and video due to Dolby Digital and MPEG-2 system.
• Various screen and audio functions can be easily selected through the onscreen menu.
VIDEO-CD
12cm 74 min.
Audio
+
Video
8cm 20 min.
• Video with CD sound, VHS quality & MPEG-1 compression technology.
AUDIO-CD
Audio
12cm
8cm
74 min.
20 min.
• CD is recorded as a
Digital Signal with better audio quality, less distortion and less deterioration of audio quality over time.
Disc Markings
~
• Play
Region
Number
NTSC
• NTSC broadcast system in U.S.A,
Canada, Korea,
Japan, etc.
• Dolby
Digital disc
STEREO
DIGITAL
SOUND
• Stereo disc • Digital
Audio disc
• DTS disc • MP3 disc
Play Region Number
Both the DVD player and the discs are coded by region. These regional codes must match in order for the disc to play. If the codes do not match, the disc will not play.
The Region Number for this player is described on the rear panel of the player.
7
DVD-P728 TWN(gb)00049T-1 7/23/02 1:25 PM Page 8
Description-Front Panel
JOG
/SHUTTLE
1 2 3 4
Front Panel Controls
1. STANDBY / ON
• When the unit is first plugged in, the indicator lights.
When STANDBY/ON is pressed on again, the light goes out and the player is turned on.
2. HEADPHONES JACK
• You can attach headphones here for private listening.
3. HEADPHONES VOLUME
• Use to adjust headphones volume level.
4. DISC TRAY
• Load the disc here.
5. DISPLAY
• Operation indicators are displayed here.
5 6 7 8 9 10 11
6. OPEN/CLOSE
• Press to open and close the disc tray.
7. SCREEN FIT
8. PLAY/PAUSE
• Begin or pause disc play.
9. SKIP/SEARCH
10. STOP
• Stops disc play.
11. JOG/SHUTTLE
• Shuttle(outer dial) - Use during DVD and CD play to fast forward or reverse.
• Jog(inner dial) - Use for frame advance/CD track selection.
2 5 6 7 8 9 10
1
11
3 4
Front Panel Display
8
1. Angle indicator. You can select multiple angles of a scene recorded by different cameras.
2. Disc type indicators
3. Reverse play / Pause / Forward play
4. Lights when 3D surround is turned on.
5. DVD : Title number
6. DVD : Chapter number.
7. Video/Audio CD : Track number
8. Repeat play mode
14 13 12
9. Linear PCM audio output
10. Dolby Digital Disc
11. DTS (Digital Theater System) output
12. MPEG-2 Audio output
13. MP3 indicators
14. Displays various messages concerning operations such as PLAY, STOP, LOAD, RANDOM, ...
no DISC : No disc loaded.
OPEN : The disc tray is open.
LOAD : Player is loading disc information.
Description-Rear Panel
SURROUND
FRONT
S/W
CENTER R1
R2
MIXBD AUDIO OUT
L2
L1
V2
V1
1 2 3 4 5 6 7
Rear Panel
1. DIGITAL AUDIO OUT JACKS
• Use either an optical or coaxial digital cable to connect to a compatible Dolby Digital receiver.
Use to connect to an A/V Amplifier that contains a Dolby Digital or DTS decoder.
2. ANALOG AUDIO OUT JACKS
• Connect to a 5.1ch analog input jack on a speaker.
3. MIXED AUDIO OUT JACKS
• Connecting to audio input jacks on your television, audio/video receiver or VCR.
4. VIDEO OUT JACK
• Use a video cable to connect to the Video input jack on your television.
• The VIDEO OUT SELECT switch must be set to the 525I(480I) position.
5. S-VIDEO OUT JACK
• Use the S-Video cable to connect this jack to the S-Video jack on your television for a higher quality picture.
• The VIDEO OUT SELECT switch must be set to the 525I(480I) position.
6. COMPONENT VIDEO OUT JACKS
• Use these jacks if you have a TV with Component Video in jacks. These jacks provide Pr, Pb and Y video. Along with S-Video, Component Video provides the best picture quality.
• If 525P(480P) VIDEO is selected, progressive scan mode will work.
• If 525I(480I) VIDEO is selected, interlaced scan mode will work.
7. VIDEO OUT SELECT SWITCH
• Use the switch to set video out.
• If 525P(480P) VIDEO is selected, VIDEO and S-VIDEO will not work.
Important Note
• Consult your TV User’s Manual to find out if your TV supports Progressive Scan.
If Progressive Scan is supported, follow the TV User’s Manual’s instructions regarding
Progressive Scan settings in the TV’s menu system.
• If 525P(480P) VIDEO OUT is Selected, VIDEO and S-VIDEO will not work.
9
DVD-P728 TWN(gb)00049T-1 7/23/02 1:25 PM Page 10
10
11
12
4
5
8
9
6
7
13
14
15
16
17
1
2
3
Tour of the Remote Control
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
1
9
27
(Easy Remote Control)
25
24
10
12
10
Tour of the Remote Control
DVD Function Buttons
1. DVD POWER Button
2. I.REPLAY Button
• This function is used to replay the previous 10 seconds of the movie from the current position.
3. NUMBER Buttons
4. SETUP Button
• Brings up the DVD player’s Setup menu.
5. VOLUME Buttons
6. TV/VIDEO Button
7. ZOOM Button
8. S.FIT Button
9. STOP Button
10. MENU Button
• Brings up the Disc menu.
11. TOP MENU Button
12. ENTER/DIRECTION Button
(UP/DOWN or LEFT/RIGHT buttons)
• This button functions as a toggle switch.
13. CLEAR Button
• Use to remove menus or status displays from the screen.
14. BOOKMARK Button
15. REPEAT Button
• Allows you to repeat play a title, chapter, track, or disc.
16. JOG DIAL
• Operates frame by frame play. In CD mode, performs track search.
17. SHUTTLE DIAL
• Performs fast or slow motion play.
18. TV POWER Button
19. SLOW Button
20. 3D Button
21. OPEN/CLOSE Button
22. CHANNEL Buttons
23. DIGEST Button
24. PLAY/PAUSE Button
• Begin/Pause disc play.
25. SKIP Buttons
• Use to skip the title, chapter, or track.
26. RETURN Button
• Returns to a previous menu.
27. DISPLAY Button
• Displays the current disc mode.
28. ANGLE Button
• Use to access various camera angles on a DVD.
29. MODE Button
• Allows you to program a specific order.
30. SUBTITLE Button
31. AUDIO Button
• Use this button to access various audio functions on a disc.
32. REPEAT A-B Button
• Use to mark a segment to repeat between A and B.
11
DVD-P728 TWN(gb)00049T-1 7/23/02 1:25 PM Page 12
Choosing a Connection
The following show examples of connections commonly used to connect the DVD player with a
TV and other components.
Before Connecting the DVD Player
• Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.
• Refer to the owner’s manual of the additional components you are connecting for more information on those particular components.
Connection to an Audio System
Method 1 Method 2 Method 3
AUDIO
2ch Amplifier
Audio Input Jacks
R L
5.1ch Analog Amplifier
Audio Input Jacks
Front (RH) Front (LH) Center
Rear (RH) Rear (LH) Subwooper
Dolby Digital Decoder
Digital Audio Input Jacks
OR
12
MIXED AUDIO OUT
R2 L2
L1
R1
Mixed Audio Out
R SURROUND L
S/W
R FRONT L CENTER
Analog Audio Out Digital Audio Out
DVD
Choosing a Connection
Connection to a TV (For Video)
TV (Normal, Widescreen, Projection, etc..)
Method 1 Method 2 Method 3
Basic Audio Good picture Better picture Best picture
Method 4
Optimum picture
TV
AV Cable
S-Video
Cable
OR
Video Cables
OR
R2
L2
DVD
1
R1 L1
MIXED AUDIO OUT
Audio Output Jacks Video Output Jack S-Video Jack Component Video Jacks
• Method 1 DVD Player + TV with Video Input Jack
(The VIDEO OUT SELECT switch must be set to the 525I(480I) position.)
• Method 2 DVD Player + TV with S-Video Input Jack
(The VIDEO OUT SELECT switch must be set to the 525I(480I) position.)
• Method 3 DVD Player + TV with Component Video Jacks
(The VIDEO OUT SELECT switch must be set to the 525I(480I) position.)
• Method 4 DVD Player + TV with Progressive Scan Jacks.
(The VIDEO OUT SELECT switch must be set to the 525P(480P) position).
•If 525P(480P) VIDEO OUT is Selected, VIDEO and S-VIDEO will not work.
•Depending on your TV, your hookup for Method 4 may differ from the illustration.
Important Note
Consult your TV User’s Manual to find out if your TV supports Progressive Scan. If Progressive Scan is supported, follow the TV User’s Manual’s instructions regarding Progressive Scan settings in the TV’s menu system.
13
DVD-P728 TWN(gb)00049T-1 7/23/02 1:25 PM Page 14
Playing a Disc
Before Play
• Turn on your TV and press the TV/VIDEO button to select the video mode.
• Turn on your Audio System and select AUX, CD or DVD.
After plugging in the player, the first time you press the DVD POWER button, this screen comes up :
If you want to select the language, press a NUMBER button.
(This screen will only appear the very first time you plug in the player.)
Select menu language
Play
Press the OPEN/CLOSE button.
The STANDBY indicator light goes out and the tray opens.
Place a disc gently into the tray with the disc’s label facing up.
Press the PLAY/PAUSE button or OPEN/CLOSE button to close the disc tray.
Stopping Play
Press the STOP button during play.
Removing Disc
Press the OPEN/CLOSE button.
Pausing Play
Press the PLAY/PAUSE or STEP button on the remote during play.
- Screen stops, no sound.
- To resume again, press PLAY/PAUSE button once again.
14
Playing a Disc
Step Motion Play (Except CD)
When the JOG DIAL is turned, you can view frames one by one.
- Each time the button is pressed, a new frame will appear.
- No sound is heard during STEP mode.
- Press PLAY/PAUSE to resume normal play.
(You can only perform step motion play in the forward direction.)
Slow Motion Play (Except CD)
- Press and hold the SKIP button to choose playback speed among 1/8X, 1/4X, and 1/2X of normal.
- No sound is heard during slow mode.
- Press PLAY/PAUSE to resume normal play.
- When playing a VCD, the reverse slow motion play will not work.
RESUME function
When you stop disc play, the player remembers where you stopped, so when you press PLAY again, it will pick up where you left off. (unless the disc is removed, the STOP button is pressed twice or the player is unplugged.)
NOTE
• If the player is left for 5 minutes in pause mode, it will stop.
• If the player is left in the stop mode for more than 30 minutes, the power will automatically shut off.
(Automatic Power-Off Function)
• If the player is left in the stop mode for more than one minute without any user interaction, a screen saver will be activated, and the TV screen will fade in and out repeatedly. Press the PLAY button to resume normal play.
• This icon indicates an invalid button press.
15
DVD-P728 TWN(gb)00049T-1 7/23/02 1:25 PM Page 16
Using the Search & Skip Functions
During play, you can search quickly through a chapter or track or use the skip function to jump to the next selection.
Searching through a Chapter or Track
Turn the shuttle diad of remote control or Jog/Shuttle on the front during disc play.
DVD
VCD/CD
2X, 4X, 8X, 16X, 32X, 128X
2X, 4X, 8X
• Depending on the disc, audio may not be heard when a disc is in 2X play mode.
Skipping Tracks
1 During play, press the NEXT SKIP ( ¨¨I) or
BACK SKIP (IÃÃ) button.
• When playing a DVD, if you press the NEXT SKIP button, it moves to the next chapter. If you press the BACK SKIP button, it moves to the beginning of the chapter.
One more press makes it move to the beginning of the previous chapter.
• When playing a VCD 2.0 in MENU OFF mode, a VCD 1.1 or a CD, if you press the NEXT SKIP button, it moves to the next track.
If you press the BACK SKIP button, it moves to the beginning of the track.
One more press makes it move to the beginning of the previous track.
• If a track exceeds 15 minutes when playing a VCD and you press the NEXT
SKIP button, it moves forward 5 minutes.
If you press the BACK SKIP button, it moves backward 5 minutes.
16
Using the Display Function
When Playing a DVD
1 During play, press the DISPLAY button on the remote.
- Current title, chapter number, elapsed time,
Audio, Subtitle, Angle, Repeat and 3D control will be displayed.
• Use the NUMBER buttons to enter a different title, then press the ENTER button.
• Use the LEFT/RIGHT or NUMBER buttons to enter a chapter number, then press the ENTER button.
• To enter the time from which you want to start, use the UP/DOWN buttons to select, then use the
NUMBER buttons to enter the time.
Then press the ENTER button.
• Use the LEFT/RIGHT buttons to change the values of the current audio, subtitle, Angle, Repeat and 3D.
• To make the screen disappear, press the DISPLAY button again.
When Playing a CD/VCD
During play, press the DISPLAY button on the remote.
- Current track number, elapsed time, Audio, Repeat and 3D control will be displayed.
• Use the UP/DOWN buttons to select a track. Use the LEFT/RIGHT buttons or NUMBER buttons to enter a different track number, then press the
ENTER button.
• To enter the time from which you want to start, use the UP/DOWN buttons to select, then use the
NUMBER buttons to enter the time.
Press the ENTER button.
• Use the LEFT/RIGHT buttons to change the values of the current audio, Repeat and 3D.
- To make the screen disappear, press the DISPLAY button again.
* In VCD 2.0 mode (MENU ON mode), only the volume control will appear on screen.
Display
Title 1 / 10
Chapter 10 / 40
Time 00 : 23 : 25
Audio ENG 5.1CH
Return
Enter
A
Subtitle Off
Angle 1 / 1
Repeat Off
3D Off
Display
Track
Time
Audio
Repeat Off
3D Off
1 / 17
00 : 00 :15
Stereo
Return
Enter
NOTE
What is a Chapter ?
Each Title on a DVD is usually divided into chapters (similar to tracks on an audio CD).
What is a Title ?
A DVD may contain several different titles.
For example, if a disc contains four different movies, each might be considered a title.
17
DVD-P728 TWN(gb)00049T-1 7/23/02 1:25 PM Page 18
Repeat Play
Repeat the current track, chapter, title, a chosen section (A-B), or all of the disc.
When playing a DVD
Press the REPEAT button on the remote. Repeat screen appears.
Select Title or Chapter using the LEFT/RIGHT buttons.
3 Press ENTER.
To return to normal play, press REPEAT again, then press the LEFT/RIGHT buttons to select Off and press ENTER.
* REPEAT A-B button
• Press the REPEAT (A-B) button to select the point where the function starts. (A)
• Press the REPEAT (A-B) button to select the point where the function ends. (B)
• To terminate the function, press the 'CLEAR' button or the
'REPEAT (A-B)' button again. Then press play to resume normal playback.
• A-B REPEAT does not allow you to set point (B) until at least 5 seconds has elapsed after point (A) has been set.
DVD
Repeat Off Title Chapter
VCD/CD
Repeat Off Track Disc
Repeat A-B
NOTE
• DVD repeats play by chapter or title, CD and VCD repeat play by disc or track.
See page 29 to MP3 disc repeat Play.
• Depending on the disc, the Repeat function may not work.
• If the title or track is completed before marking the end (B), the end of title or track becomes B automatically.
• When in VCD 2.0 mode (MENU ON mode), this function does not work.
18
Program Play & Random Play
Program Play (DVD/VCD/CD)
1 Press the MODE button.
2 Use the LEFT/RIGHT buttons to select PROGRAM.
Press the ENTER button.
Use the UP/DOWN/LEFT/RIGHT buttons to select the first chapter (or track) to add to the program.
Press the ENTER button. The selection numbers appear in the Program Order box.
PROGRAM
Chapters of Title 01
01 02 03 04
05 06 07 08
09 10 11 12
13 14 15 16
17
Program order
-- -- -- --
-- -- -- --
-- -- -- --
-- -- -- --
-- -- -- --
Clear last chapter
Clear all chapters
Press the PLAY/PAUSE button. The disc will be played in programmed order.
Random Play (DVD/VCD/CD)
Press the MODE button.
2 Use the LEFT/RIGHT buttons to select RANDOM.
Press the ENTER button.
The disc will be played in random order.
M
Mode 1 Program ?
Ramdom On
NOTE
• Depending on the disc, the Program and Random Play function may not work.
• When in VCD 2.0 mode (MENU ON mode), these functions do not work.
• To resume normal play, press the CLEAR button.
19
DVD-P728 TWN(gb)00049T-1 7/23/02 1:25 PM Page 20
S.FIT Play
Screen Fit Play
1 During play, press S.FIT button on remote control.
- Allows you to eliminate the black bars in the top and bottom of the screen.
- Screen Fit will not work when the Zoom mode is active.
(you can not remove the black bars on the screen)
However, Zoom mode will work when Screen Fit is active.
Digest Play
Digest Play
1 During play, press the DIGEST button.
- You'll see the 6 individual windows representing each of the chapters on the TV screen.
- When each window is displayed, the first 3 seconds of the chapter will be played.
Press UP/DOWN/LEFT/RIGHT buttons or NUMBER button to select the window you'd like to see, and press the ENTER button.
- Up to 6 windows(chapters) can be displayed on the screen at a time.
- Press the 'Skip' button for the next 6 chapters if the movie has more than 6.
SKIP button
NOTE
• Various aspect ratios are available only in multiple screen format discs.
• This function does not work when a DVD has been recorded in a multi-camera angle format.
• On some DVDs, the black bars cannot be eliminated due to their aspect ratio.
20
NOTE
• You can play the DVD player starting with the desired chapter after directly moving to the scene you want.
• 'DIGEST' may not operate depending on the disc in use.
21
DVD-P728 TWN(gb)00049T-2 7/23/02 1:27 PM Page 26
Using the Disc View Function
Index View (VCD)
Displays the equally divided 6 views of the current playing track.
During play, press the DIGEST button.
Press LEFT/RIGHT buttons to select Index View.
Press the ENTER button.
3 Select the desired view by pressing
UP/DOWN or LEFT/RIGHT buttons.
- Press the SKIP button for the next 6 tracks if the movie has more than 6.
4 Press the ENTER button.
Track View (VCD)
Displays the beginning view of each track and the track number.
During play, press the DIGEST button.
Press the LEFT/RIGHT buttons to select Track
View. Press the ENTER button.
Select the desired view by pressing the
UP/DOWN or LEFT/RIGHT buttons.
Press the ENTER button.
View Index Track
View Index Track
NOTE
• When pressing the TOP MENU button with a DVD; the disc’s TITLE MENU function comes up. A disc must have at least two titles for the TITLE MENU function to work.
• When pressing the TOP MENU button with a CD; the unit enters the INTRO mode. INTRO lets you listen to the beginning of each track for about 10 seconds.
• When in VCD 2.0 mode (MENU ON mode), this function does not work.
22
Selecting the Audio Language
You can select a desired language quickly and easily with the AUDIO button.
Using the AUDIO button
Press the AUDIO button.
DVD
Audio ENG Dolby Digital 5.1CH
Use the LEFT/RIGHT buttons to select the desired language on a DVD.
- The audio languages are represented by abbreviations.
Use the LEFT/RIGHT buttons to select
Stereo, Right or Left. (On VCD/CD)
VCD/CD
Audio Stereo
NOTE
• This function depends on what languages are encoded on the disc and may not work with all DVDs.
• A DVD disc can contain up to 8 audio languages.
• How to have the same audio language come up whenever you play a DVD;
Refer to “Setting Up the Language Features” on page 33.
23
DVD-P728 TWN(gb)00049T-2 7/23/02 1:27 PM Page 28
Selecting the Subtitle Language
You can select a desired subtitle quickly and easily with the SUBTITLE button.
Using the SUBTITLE button
1 Press the SUBTITLE button.
2 Use the LEFT/RIGHT buttons to select the desired subtitle language.
Use the UP/DOWN buttons to determine whether or not the subtitle will be displayed.
- Initially, the subtitling will not appear on screen.
- The subtitle languages are represented by abbreviations.
A
Subtitle ENG Off
A
Subtitle ENG On
Changing the Camera Angle
When a DVD contains multiple angles of a particular scene, you can select the Angle function.
Using the ANGLE button
Press the ANGLE button to see if an ANGLE ( mark is present at the upper right hand corner of the screen.
)
When an ANGLE mark is shown, press the
ANGLE button, then an ANGLE select icon will appear at the upper left hand corner of the screen.
Use the LEFT/RIGHT buttons to select the desired screen angle.
To turn off the display, press the ANGLE button again.
Angle 1/6
NOTE
• This function depends on what languages are encoded on the disc and may not work with all DVDs.
• A DVD disc can contain up to 32 subtitle languages.
• How to have the same subtitle language come up whenever you play a DVD;
Refer to “Setting Up the Language Features” on page 33.
24 25
DVD-P728 TWN(gb)00049T-2 7/23/02 1:27 PM Page 30
Using the Instant Replay Function
Using the Instant Replay function (DVD)
If you miss a scene, you can see it again using this function.
If you press the I.REPLAY button, the current scene moves backward about 10 seconds, and plays back.
* Depending on the disc, the Instant Replay function may not work.
I. Replay
Using the Bookmark Function
The Bookmark function lets you select parts of a DVD or VCD (MENU OFF mode) so that you can quickly find the section at a later time.
Using the Bookmark Function (DVD/VCD)
1 During play, press the BOOKMARK button on the remote. The Bookmark icons will be displayed.
Use the LEFT/RIGHT buttons to move to the desired bookmark icon.
3 When you reach the scene you want to mark, press the ENTER button. The icon will change to a number (1, 2, or 3).
4 Press the BOOKMARK button to turn off the display.
Recalling a Marked Scene
During play, press the BOOKMARK button on the remote.
Use the LEFT/RIGHT buttons to select a marked scene.
Press the PLAY/PAUSE buttons to skip to the marked scene.
Bookmark - - - - - -
Bookmark 1 2 3
Clearing a Bookmark
During play, press the BOOKMARK button on the remote.
Use the LEFT/RIGHT buttons to select the bookmark number you want to delete.
Press the CLEAR button to delete a bookmark number. Press the BOOKMARK button to turn off display.
NOTE
• Up to three scenes may be marked at a time.
• When in VCD 2.0 mode (MENU
ON mode), this function does not work.
• Depending on the disc, the
Bookmark function may not work.
27 26
DVD-P728 TWN(gb)00049T-2 7/23/02 1:27 PM Page 32
Using the Zoom & 3D Sound Functions
28
Using the Zoom Function (DVD/VCD)
During play or pause mode, press the
ZOOM button on the remote.
A square will be displayed on screen.
Use the UP/DOWN or LEFT/RIGHT buttons to select the part of the screen you want to zoom in on.
3 Press the ENTER button.
- During DVD play, press ENTER to zoom in
2X/4X/2X/Normal in order.
- During VCD play, press ENTER to zoom in
2X/normal in order.
Using the 3D Sound Function
The simulated surround effect depends on the disc contents. If you connect the unit to your stereo system, you can enhance sound quality and produce a greater surround effect.
This feature is useful when you are using the DVD player with a two channel stereo through the analog outputs.
(Discs which are recorded with LPCM or DTS will not work. When the DIGITAL OUTPUT is set to BIT
STREAM in the SETUP MENU, the 3D Sound function will not work.)
During play, press the 3D button.
The 3D SOUND mark will be displayed on screen. (Be sure the DIGITAL OUTPUT is set to
PCM.)
2 Press the UP/DOWN buttons to turn the 3D
Sound feature on or off.
+
3D Sound Off
NOTE
• 3D Sound is possible only on discs recorded using DOLBY SURROUND or
DOLBY DIGITAL. However, some of these discs do not contain rear channel sound signals.
• Depending on the disc, the Zoom and
3D Sound function may not work.
MP3 Play
When an MP3 Disc is inserted into the DVD PLAYER, the first song file of the first Directory plays.
MP3 Play Function
To returned playback of the first song file, then press
RETURN to display the music files menu on the right side of the screen, the music Directory menu on Ieft side of the Screen. Up to 10 music Directories can be displayed at a time. If you have more than 10
Directories on a disc, press the LEFT/RIGHT buttons to bring them up on the screen.
HJLN01
Return
Enter
10 Directory
HJUN
BACKJY
BANK
COOL
DJDOC
BABYBOX
J
JACKKI
KIMHJ
KOHK
00:02
13 Files
HJLN01
HJLN02
HJLN03
HJLN04
HJLN05
HJLN06
HJLN07
HJLN08
HJLN09
HJLN10
Off
2 Use the UP/DOWN buttons to select the desired music
Directory, the press ENTER. Use the UP/DOWN buttons again to select a song file. Press ENTER to begin playback of the song file.
Program/Random playback
Press the MODE button, then the UP/DOWN buttons, to switch between the RANDOM and PROGRAM modes.
See page 19 for more information on these modes.
NOTE
• Press the REPEAT button to hear a song file repeatedly.
Press Repeat again to release the Repeat mode.
• Depending on the disc, the Program and Random Play function may not work.
• To resume normal play, press the CLEAR button.
• It does not work SETUP MENU in CD-R (MP3).
Return
Enter
HJLN01
HJUN 13 Files
HJLN01
HJLN02
HJLN03
HJLN04
HJLN05
HJLN06
HJLN07
HJLN08
HJLN09
HJLN10
00:10 Off
Progrm Play
Progrm Order :05
HJLN01
HJLN02
HJLN03
HJLN04
HJLN05
29
DVD-P728 TWN(gb)00049T-2 7/23/02 1:27 PM Page 34
MP3 Play
CD-R/MP3 requirements
When playing CD-R MP3 discs, please follow the recommendations below:
• Your MP3 files should be ISO 9660 or JOLIET format.
ISO 9660 format and Joliet MP3 files are compatible with Microsoft's DOS and Windows, and with Apple's
Mac. These two formats are the most widely used.
• When naming your MP3 files do not exceed 8 characters, and place ".mp3" as the file extension.
General name format of: Title.mp3. When composing your title, make sure that you use 8 characters or less, have no spaces in the name, and avoid the use of special characters including: (.,/,\,=,+).
• Use a decompression transfer rate of at least 128 Kbps when recording MP3 files.
Sound quality with MP3 files basically depends on the rate of compression/decompression you choose.
Getting audio CD quality sound requires an analog/digital sampling rate (conversion to MP3 format) of at least 128 Kbps and up to 160 Kbps. However, choosing higher rates, like 192 Kbps or more, only rarely give better sound quality.
Conversely, files with sampling rates below 128 Kbps will not be played properly.
• Do not try recording copyright protected MP3 files.
Certain "securized" files are encrypted and code protected to prevent illegal copying. These files are of the following types: Windows Media TM (registered trade mark of Microsoft Inc) and SDMI mark of The SDMI Foundation). You cannot copy such files.
TM (registered trade
• Your DVD player only accepts one level of file directory.
Consequently you must choose:
-either to save all your MP3 recording files at the root of the disc;
-and/or create folders in the directory for each artist or music type (e.g.classical, rock, jazz, etc)
• Important: The above recommendations cannot be taken as a guarantee that the DVD player will play MP3 recordings, or as an assurance of sound quality.
You should note that certain technologies and methods for MP3 file recording on CD-Rs prevent optimal playback of these files on your DVD player (degraded sound quality and in some cases, inability of the player to read the files).
Using the Setup Menu
The Setup menu lets you customize your DVD player by allowing you to select various language preferences, set up a parental level, even adjust the player to the type of television screen you have.
With the unit in Stop mode, press the SETUP button on the remote.
Language
Language
• Player Menu: Setup of the Display Language
Use the Player preference menu to select the language for the player’s on-screen displays.
• Disc Menu : Setup of the Menu Language
Use the Menu preference menu to select the language you want a
DVD’s disc menu to be displayed in.
• Audio : Setup of the Audio Language
Use the Audio preference menu to select the soundtrack language.
Parental
Audio
Display
• Subtitle : Setup of the Subtitle Language
Use the Subtitle preference menu to select the language the disc’s subtitles are to be displayed in.
Parental : Setup of the Parental Level
Allows users to set the level necessary to prevent children from viewing unsuitable movies such as those with violence, adult subject matter, etc.
Audio : Setup of the Audio Options
Display : Setup of the Display Options
Use to select which type of screen you want to watch and several display options.
2 Use the UP/DOWN buttons on the remote to access the different features.
3 Press the ENTER button to access the sub features.
To make the setup screen disappear after setting up, press the
SETUP button again.
NOTE
Player Menu
Disc Menu
Audio
Subtitle
Depending on the disc, some
Setup Menu selections may not work.
English
English
English
Automatic
Return
Enter
31 30
DVD-P728 TWN(gb)00049T-2 7/23/02 1:27 PM Page 36
Setting Up the Language Features
If you set the player menu, disc menu, audio and subtitle language in advance, they will come up automatically every time you watch a movie.
Using the Player Menu Language
1
2
3
4
5
With the unit in Stop mode, press the
SETUP button. Then press the ENTER button.
Use the UP/DOWN buttons to select the
Player Menu .
Press the ENTER button.
Use the UP/DOWN buttons to select
‘English’.
Press the ENTER button.
- English is selected and the screen returns to SETUP
MENU.
- To make the SETUP MENU disappear, press the
RETURN button.
Using the Disc Menu Language
This function changes the text language only on the disc menu screens.
With the unit in Stop mode, press the
SETUP button. Then press the ENTER button.
2
3
4
Use the UP/DOWN buttons to select
Disc Menu .
Press the ENTER button.
Use the UP/DOWN buttons to select
‘English’.
- Select “Others” if the language you want is not listed.
5 Press the ENTER button.
- English is selected and the screen returns to SETUP
MENU.
e.g
Setting up in English.
Language
Parental
Audio
Display
Return
Enter
Player Menu
Disc Menu
Audio
Subtitle
English
English
English
Automatic
Language
Parental
Audio
Display
Disc Menu
Audio
Subtitle
Player Menu
English
English
English
English
Return
Enter e.g
Setting up in English.
Language
Parental
Audio
Display
*
Player Menu
Disc Menu
Audio
Subtitle
Disc Menu
English
English
English
English
Others
Return
Enter
32
Setting Up the Language Features
Using the Audio Language
With the unit in Stop mode, press the SETUP button. Then press the ENTER button.
Press the UP/DOWN buttons to move to Audio.
Press the ENTER button.
Language
Parental
Audio
Display
Audio
Return
Enter
Player Menu
*
Original
English
Disc Menu
Audio
Subtitle
English
English
English
Others
Press the UP/DOWN buttons to select ‘English’.
- Select “Original” if you want the default soundtrack language to be the original language the disc is recorded in.
- Select “Others” if the language you want is not listed.
Press the ENTER button.
- English is selected and the screen returns to SETUP MENU.
Using the Subtitle Language
Return
Enter
1
2
With the unit in Stop mode, press the SETUP button. Then press the ENTER button.
Use the UP/DOWN buttons to select Subtitle.
3 Press the ENTER button.
4 Use the UP/DOWN buttons to select ‘English’.
- Select “Automatic” if you want the subtitle language to be the same as the language selected as the audio preference.
- Select “Others” if the language you want is not listed. Some discs may not contain the language you select as your initial language; in that case the disc will use its original language setting.
Language
Parental
Audio
Display
*
Player Menu
Automatic
English
Disc Menu
Audio
Subtitle
Subtitle
NOTE
English
English
English
Others
• If the selected language is not recorded on the disc, the original pre-recorded language is selected.
5 Press the ENTER button.
- English is selected and the screen returns to SETUP MENU.
• How to make the SETUP MENU disappear or return to menu screen during set up; Press RETURN button.
33
DVD-P728 TWN(gb)00049T-2 7/23/02 1:28 PM Page 38
Setting Up the Parental Control
34
The Parental Control function works in conjunction with DVDs that have been assigned a rating - which helps you control the types of DVDs that your family watches.
There are up to 8 rating levels on a disc.
Return
Enter
Language
Parental
Audio
Display
Create
Player Menu
Enter Password
? - - -
Password
Language
Parental
Audio
Display
Return
Enter
With the unit in Stop mode, press SETUP button.
Use UP/DOWN to select Parental. Press ENTER.
The Parental Control screen appears.
Use LEFT/RIGHT to select On if you want to use a password. The Enter Password screen appears.
Enter your password. The Re-enter Password screen appears to confirm the password. Enter your password again. The Parental Control screen appears.
5 About the Rating Level ;
The Rating Level will work only when Use
Password is set to On. To unlock the player, use LEFT/RIGHT to select Off. Use UP/DOWN to select Rating level. Press ENTER.
- Use UP/DOWN to select the level(e.g. Level 6) and press
ENTER. Discs that contain Level 7 will now not play.
- To cancel the rating level, use LEFT/RIGHT to select Off in Use Password.
6 About Change Password;
- Use UP/DOWN to select Change Password.
The Change Password screen appears.
- Enter your new password.
Re-enter the new password again.
Language
Parental
Audio
Display
Use Password Off
Use Password On
Rating Level
Change Password
6 e.g
Setting up in LEVEL6.
Return
Enter
Return
Enter
Language
Player Menu
Rating Level
Parental
Audio
Display
Rating Level
6
NOTE
• How to make the SETUP MENU disappear or return to menu screen during set up;
Press RETURN button.
• If you have forgotten your password, see Forgot Password in the Troubleshooting Guide.
Setting Up the Audio
With the unit in Stop mode, press the SETUP button.
2 Use the UP/DOWN buttons to select Audio. Then press the ENTER button.
Use the UP/DOWN buttons to select the desired item. Then press the LEFT/RIGHT buttons.
Language
Parental
Audio
Display
Digital Output
1. PCM : Converts to PCM(2CH) audio.
Select PCM when using the Analog
Audio Outputs.
2. Bitstream : Converts to Dolby DigitalBitstream
(5.1CH). Select Bitstream when using the Digital Audio Output.
N O TT TT EE : Be sure to select the correct Digital Output or no audio will be heard.
DTS
1 . Off : Doesn’t output digital signal.
2 . On : Outputs DTS Bitstream via digital output only.
Select DTS when connecting to a DTS Decoder.
Dynamic Compression
1 . On : To select dynamic compression.
2 . Off : To select the standard range.
2X Scan Audio
1 . Off : Turns 2X audio off.
Though 2X Scan Audio is ON in the SETUP
MENU, no sound will be heard on discs which are recorded with LPCM, DTS or MPEG-2
Audio.
2 . On : Turns 2X audio on.
Speaker
Return
Enter
Digital Output
DTS
Dynamic Compression
2x Scan Audio
Speaker
PCM
Off
On
On
NOTE
• How to make the SETUP MENU disappear or return to menu screen during set up; Press RETURN button.
• Manufactured under license from Dolby Laboratories.
”Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
• “DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
35
DVD-P728 TWN(gb)00049T-2 7/23/02 1:28 PM Page 40
Surround Sound Speaker Setup
Press the SETUP button in play or stop mode.
2 Press the UP/DOWN buttons to select Audio.
Then press the ENTER button.
Parental
Audio TEST
Display
SL 3 Use the UP/DOWN buttons to select Speaker.
Then press the ENTER button.
4 Use the UP/DOWN or LEFT/RIGHT buttons to select the desired item. Then press the ENTER button.
Setting up SPEAKER MODE
• If you have connected the system to a speaker with low frequencies of 100Hz or below, select ‘Found (Large illustration)’.
• If you have connected the system to a speaker without low frequencies of 100Hz or below, select ‘Found(Small illustration)’. If you don’t connect a subwoofer, always select
‘Found(Large illustration)’ for the Front Speakers(L/R).
• When you don’t have a particular speaker connected, select ‘Not found
(No illustration visible)’.
Setting up TEST
The test output signals come clockwise starting from the Front Speaker(L). Adjust Channel
Balance to match to the volume of test signals memorized in the system.
FRONT(L) CENTER FRONT(R) SUBWOOFER
SURROUND(R) SURROUND(L)
C
R
SR
SW
NOTE
• How to make the SETUP MENU disappear or return to menu screen during set up.
Press RETURN button.
• The subwoofer test output signal is lower than the other speakers.
• The MPEG Multichannel logo is a trademark registered by PHILIPS Corporation.
36
Setting Up the Display
1 With the unit in Stop mode, press the SETUP button.
2 Use the UP/DOWN buttons to select Display. Then press the ENTER button.
Use the UP/DOWN buttons to select the desired item.
Then press the LEFT/RIGHT buttons.
TV Aspect
Depending on the type of television you have, you may want to adjust the screen setting (aspect ratio).
1 . Letter Box :
Select when you want to see the total 16:9 ratio screen DVD supplies, even though you have a TV with a 4:3 ratio screen.
Black bars will appear at the top and bottom of the screen.
2 . Pan-Scan :
Select this for conventional size TVs when you want to see the central portion of the 16:9 screen. (Extreme left and right side of movie picture will be cut off.)
3 . Wide :
You can view the full 16:9 picture on your widescreen TV.
Still Mode
These options will help prevent picture shake in still mode and display small text clearer.
1 . Auto : When selecting Auto, Field/Frame mode will be automatically converted.
2 . Frame : Select this feature when you want to see small letters more clearly in the Auto mode.
3 . Field : Select this feature when the screen shakes in the Auto mode.
Screen Messages
Use to turn on-screen messages On or Off.
Front Display
Adjust the brightness of the unit’s front panel display.
1 . Auto Dim : Makes the Front Panel Display dim automatically when playing a DVD.
2 . Dim : Makes the Front Panel Display dim.
3 . Bright : Makes the Front Panel Display bright.
Black Level
Adjusts the brightness of the screen.(On/Off)
You are unable to adjust picture brightness in case you select progressive video out.
Language
Parental
Audio
Display
Return
Enter
TV Aspect Wide
Still Mode
Screen Messages
Front Display
Black Level
Auto
On
Auto Dim
On
NOTE
• How to make the SETUP MENU disappear or return to menu screen during set up;
Press the RETURN button.
37
DVD-P728 TWN(gb)00049T-2 7/23/02 1:28 PM Page 42
Controlling a TV with the Remote
The remote can also be set up to control most TVs. To program the remote, use the code that corresponds to your brand.
Code
10
11
12
13
14
15
05
06
07
08
09
01
02
03
04
TV Codes
Brand
SAMSUNG_1
SHARP_2
SONY
MAGNAVOX
SANYO_1
LG_2
RCA
LG_1
TOSHIBA
HITACHI
JVC
PANASONIC_1
MITSUBISHI_2
SAMSUNG_2
SAMSUNG_3
Code
20
21
22
23
24
16
17
18
19
25
26
27
28
29
Brand
SHARP_1
ZENITH
LG_3
DAEWOO_8
SANYO_2
EMERSON
SHARP_3
SAMSUNG_4
PANASONIC_2
NOBLEX
TELEFUNKEN
NEWSAN
LOEWE
RCA2
38
Turn on the TV.
If the TV turns off, setup is complete.
2 Point the DVD’s remote at the TV.
3 While holding the TV POWER button down, enter the code for your brand.
e.g
For SAMSUNG _1 TVs
While holding down the TV POWER button, enter 0 and then 1.
Enter other codes of the same brand if the first code does not work.
To operate the TV, use the “TV Function
Buttons” described on page 11.
NOTE
The remote may not be able to control every model
TV of the brands listed.
Troubleshooting
Before requesting service (troubleshooting), please check the following.
Problem
No operations can be performed with remote.
Disc does not play.
5.1 channel sound is not being reproduced.
The icon appears on screen.
Disc Menu doesn’t appear.
Play mode differs from the
Setup Menu selection.
The screen ratio cannot be changed.
No audio.
Forgot password
If you experience other problems.
Action
• Check the batteries in the remote. May need replacing.
• Operate the remote control at a distance of no more than 20 feet.
• Remove batteries and hold down one or more buttons for several minutes to drain the microprocessor inside the remote to reset it.
Reinstall batteries and try remote again.
• Ensure that the disc is installed with the label side facing up.
• Check the region number of the DVD.
• 5.1 channel sound is reproduced only when the following conditions are met. :
1) The DVD player is connected with the proper amplifier
2) The disc is recorded with 5.1 channel sound.
• Check whether the disc being played has the “Dolby 5.1 ch” mark on the outside.
• Check if your audio system is connected and working properly.
• In a SETUP Menu, is the Audio Output set to Bitstream?
• The features or action cannot be completed at this time because:
1. The DVD’s software restricts it.
2. The DVD’s software doesn’t support the feature (e.g., angles).
3. The feature is not available at the moment.
4. You’ve requested a title or chapter number or search time that is out of range.
• Check if the disc has a Menu.
• Some of the functions selected in the Setup Menu may not work properly if the disc is not encoded with the corresponding function.
• The Screen Ratio is fixed on your DVDs.
• Make sure you have selected the correct Digital Output in the Audio
Options Menu.
• Press power on from a cold start with no disc in the unit. Press the STOP and PLAY buttons simultaneously on the front panel for three seconds. The
Select Menu Language display will appear. Select the desired language button. Press the SETUP button on the remote control to select the Parental
Mode. The Parental Mode is now unlocked as indicated on the display.
Press the DOWN button to select Parental. Press ENTER and the Create
Password display will appear. You can now set your rating level and change your password to a new number.
• Go to the contents and find the section of the instruction book that contains the explanations regarding the current problem, and follow the procedure once again.
• If the problem still cannot be solved, please contact your nearest authorized service center.
Page
P4
P7
P12
P15
P31~32
P31~37
P37
P35
P34
39
DVD-P728 TWN(gb)00049T-2 7/23/02 1:28 PM Page 44
Specifications
General
Disc
Video
Output
Audio
Output
Power Requirements
Power Consumption
Weight
Dimensions
Operating Temperature Range
Operating Humidity Range
DVD
(DIGITAL VERSATILE DISC)
CD : 12Cm
(COMPACT DISC)
CD : 8Cm
(COMPACT DISC)
VCD : 12Cm
Composite Video
Component Video
S-VIDEO
2 channel
*Frequency Response
*S/N Ratio
*Dynamic Range
*Total Harmonic Distortion
AC 110~240V, 50/60 Hz
16 W
2.8 Kg
430mm ✕ 240mm ✕ 79mm
+5°C to +35°C
10 % to 75 %
Reading Speed : 3.49 m/sec
.
Approx. Play Time
(Single Sided, Single Layer Disc) : 135 min.
Reading Speed : 1.2 to 1.4 m/sec.
Maximum Play Time : 74 min.
Reading Speed : 1.2 to 1.4 m/sec.
Maximum Play Time : 20 min.
Reading Speed : 1.2 to 1.4 m/sec.
Maximum Play Time : 74 min. (Video + Audio)
1 channel : 1.0 Vp-p (75 Ω load)
Y : 1.0 Vp-p (75 Ω load)
Pr : 0.70 Vp-p (75 Ω load)
Pb : 0.70 Vp-p (75 Ω load)
Luminance Signal : 1.0 Vp-p (75 Ω load)
Chrominance Signal : 0.286 Vp-p (75 Ω load)
L(1/L), R(2/R)
48 kHz Sampling : 4 Hz to 22 kHz
96 kHz Sampling : 4 Hz to 44 kHz
110 dB
100 dB
0.004 %
*: Nominal specification
• Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
• Weight and dimensions are approximate.
40
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement