Samsung MM-G25 User manual

MM-G25

Micro Component Audio system

CD/MP3-CD/WMA-CD/CD-R/RW Playback user manual

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register your product at www.samsung.com/global/register

ENG

Safety Warnings

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

This symbol indicates “dangerous voltage” inside the product that presents a risk of electric shock or personal injury.

TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE REAR COVER (or BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

This symbol indicates important instructions accompanying the product.

CLASS 1 LASER PRODUCT

KLASSE 1 LASER PRODUKT

LUOKAN 1 LASER LAITE

KLASS 1 LASER APPARAT

PRODUCTO LASER CLASE 1

CLASS 1 LASER PRODUCT

This Compact Disc player is classified as a CLASS 1

LASER product.

Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

CAUTION : INVISIBLE LASER RADIATION WHEN OPEN AND

INTERLOCKS DEFEATED, AVOID EXPOSURE TO BEAM.

WARNING : To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

CAUTION : TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

• This apparatus shall always be connected to a AC outlet with a protective grounding connection.

• To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable.

CAUTION

• Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

• The Mains plug is used as a disconnect device and shall stay readily operable at any time.

Wiring the Main Power Supply Plug (UK Only)

IMPORTANT NOTICE

The main lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face of the plug and if it requires replacing, a fuse approved to BS1362 of the same rating must be used.

Never use the plug with the fuse cover removed. If the cover is detachable and a replacement is required, it must be of the same colour as the fuse fitted in the plug.

Replacement covers are available from your dealer.

If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should obtain a suitable safety approved extension lead or consult your dealer for assistance.

However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do not connect the plug to a main socket as there is a risk of shock hazard from the bared flexible cord.

Never attempt to insert bare wires directly into a main socket. A plug and fuse must be used at all times.

IMPORTANT

The wires in the main lead are coloured in accordance with the following code:– BLUE = NEUTRAL BROWN = LIVE

As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows:–

The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK.

The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.

WaRninG : dO nOt cOnnect eitheR WiRe tO the eaRth teRMinal Which is MaRKed With the letteR e OR BY the eaRth sYMBOl , OR cOlOuRed GReen OR GReen and YellOW.

What’s included

(Check for the supplied accessories below.)

2

FM Antenna User's Manual Remote Control

Contents

Thank you for buying this

SAMSUNG micro-compact system.

Please take time to read these instructions.

They will allow you to operate your system with ease and take full advantage of its features.

S afety

W arningS ................................................................................................................................................................................... 2 i nStalling

y our

M icro

-c oMpact

S ySteM

Front Panel View ...................................................................................................................................................................................... 4

Top Panel View ....................................................................................................................................................................................... 4

Rear Panel View ..................................................................................................................................................................................... 5

Remote Control ........................................................................................................................................................................................ 5

Where to Install Your Micro-Compact System ......................................................................................................................................... 6

Connecting your System to the Power Supply......................................................................................................................................... 6

Inserting Remote Control Batteries .......................................................................................................................................................... 6

Connecting the Loudspeakers.................................................................................................................................................................. 6

Connecting to an External Source ........................................................................................................................................................... 7

Connecting the FM Aerial ......................................................................................................................................................................... 7

Demo/Dimmer function ............................................................................................................................................................................. 8

Setting the Clock ...................................................................................................................................................................................... 8 cD/Mp3/WMa-cD-p layer

To play the CD/MP3/WMA-CD ................................................................................................................................................................. 9

Selecting a Track...................................................................................................................................................................................... 9

Searching for a Specific Music Passage on a CD ................................................................................................................................... 9

Function to skip through 10 track at a time ............................................................................................................................................. 10

Remain Function ..................................................................................................................................................................................... 10

Display Function ...................................................................................................................................................................................... 10

Repeating One or All Tracks on the Compact Discs ............................................................................................................................... 11

A-B Repeat Playback ............................................................................................................................................................................... 11

Programming the Order of CD Playback ................................................................................................................................................. 11

Checking or Changing Programmed CD Tracks ...................................................................................................................................... 12 u

Sb

Playing USB ............................................................................................................................................................................................ 12

To use high speed search ........................................................................................................................................................................ 13

To repeat .................................................................................................................................................................................................. 13

Remain Function ..................................................................................................................................................................................... 13

To skip next 10 tracks .............................................................................................................................................................................. 13

To repeat section...................................................................................................................................................................................... 13

Selecting a Track from USB Device ......................................................................................................................................................... 13 t uner

About RDS broadcasting ......................................................................................................................................................................... 14

About RDS DISPLAY function ................................................................................................................................................................ 14

PTY(Program Type) indication and PTY-SEARCH function ................................................................................................................... 15

Searching for and Storing the Radio Stations ......................................................................................................................................... 16

Selecting a Stored Station ........................................................................................................................................................................ 17

Improving Radio Reception ..................................................................................................................................................................... 17 o ther

f unctionS

CD Ripping Function ................................................................................................................................................................................ 18

Timer Function ......................................................................................................................................................................................... 19

Cancelling the Timer ................................................................................................................................................................................ 19

Mute Function ........................................................................................................................................................................................... 20

Selecting EQ Mode ................................................................................................................................................................................. 20

Treble Level Function ............................................................................................................................................................................... 20

Bass Level Function ................................................................................................................................................................................. 20

Power Sound Function ............................................................................................................................................................................. 20

Power Bass Function ............................................................................................................................................................................... 20

Setting the System to Switch off Automatically ........................................................................................................................................ 21

Connecting Headphones .......................................................................................................................................................................... 21 r ecoMMenDationS for

u

Se

Safety Precautions ................................................................................................................................................................................... 22

Cleaning Your Micro-Compact System .................................................................................................................................................... 22

Precautions When Using Compact Discs ................................................................................................................................................ 22

Before Contacting the After-Sales Service............................................................................................................................................... 23

Technical Specifications ........................................................................................................................................................................... 24

ENG

Press Push

Symbols

Important Note 3

ENG

Front Panel View

1

5

2

1. wINDOw DISPLAy

2. COMPACT DISC COMPARTMENT

3. HEADPHONE JACK

Top Panel View

3 4

4. USb JACK

5. vOLUME CONTROL bUTTON

1.

2.

3.

4.

5.

POwER bUTTON

FUNCTION bUTTON

SEARCH FUNCTION bUTTON(DOwN)

TUNING MODE OR STOP bUTTON

PLAy/PAUSE bUTTON

6. SEARCH FUNCTION bUTTON(UP)

7. CD OPEN/CLOSE bUTTON

4

1 2 3 4 5 6 7

Rear Panel View

1.

2.

3.

AUX IN

FM Aerial Connector Terminal

Speaker Connector Terminals

4. Clamp-wire

(Fasten the speaker wires.)

ENG

1

Remote Control

15

16

17

9

11

7

8

4

5

6

12

13

14

1

2

2 3

37

36

35

33

32

31

30

29

28

27

26

25

24

23

22

21

20

19

18

1. POwER

2. TUNER

3. CD

4. TIMER/CLOCK

5. TIMER ON/OFF

6. CD RIPPING

7. TUNING MODE

8. MO/ST

9. DISPLAy

10. +10

11. Skip and Search

12. Fast-Rewind

13. STOP

14. POwER SOUND

15. vOLUME -

16. TREb/bASS

17. REPEAT

18. TUNING

19. REPEAT A-b

20. P.bASS

21. MUTE

22. vOLUME +

23. TUNING

24. EQ

25. PLAy

26. Fast-Forwardy

27. PAUSE

28. RDS DISPLAy

29. RDS PTy

30. PROGRAM/SET

4

31. REMAIN

32. DEMO

33. SLEEP

34. USb

35. AUX

36. DIMMER

37. OPEN/CLOSE

5

ENG

Where to Install Your Micro-Compact

System

To take full advantage of your new micro-compact system, follow these installation instructions before connecting the unit.

Install the system on a flat, stable surface.

Never place this unit on carpeting.

Never place this unit in an outdoor area.

Maintain an open space of approximately 6 inches (15 cm) on the sides and rear of the system, for ventilation purposes.

Make sure that you have enough room to open the compact disc compartment easily.

Place the loudspeakers at a reasonable distance on either side of the system to ensure good stereo sound.

Direct the loudspeakers towards the listening area.

For optimum performance, make sure that both speakers are placed at an equal distance above the floor.

Inserting Remote Control Batteries

Insert or replace remote control batteries when you:

Purchase the micro-compact system

Find that the remote control is no longer operating correctly

When replacing the batteries, use a new set of batteries and never mix alkaline and manganese batteries.

1 Place your thumb on the position marked on the battery compartment cover (rear of the remote control) and pull the cover in the direction of the arrow.

2

Insert two AAA, LR03 or equivalent batteries, taking care to respect the polarities:

+ on the battery against + in the battery compartment

– on the battery against – in the battery compartment

3

Replace the cover by sliding it back until it clicks into position.

If you will not be using the remote control for a long time, remove the batteries to prevent corrosion.

The remote control can be used up to approximately 7 meters in

a straight line. It can also be operated at a horizontal angle of up

to 30° from the remote control sensor.

Connecting your System to the

Power Supply

Before plugging your system into a main socket, you must check the voltage.

1

2

Plug the main lead into an appropriate socket.

Press the ( STANDby/ON) button to switch your micro-compact system .

Connecting the Loudspeakers

The loudspeaker connector terminals are located on the rear of the system.

There are two terminals on the system: left speaker (marked L) right speaker (marked R)

To achieve the correct sound quality,insert those speaker connector cables to the speaker connector terminals of the system.

6

Connecting to an External Source Connecting the FM Aerial

The auxiliary input can be used to take advantage of the sound quality of your micro-compact system when listening to other sources.

Examples: A television

A DVD player

A VCR

To connect to the external source, the source must have an audio output. In addition, you need an connection cable.

How to connect a COAXIAL TYPE aerial.

Connect a 75Ω antenna to the FM antenna terminal.

Plug the connector on the FM aerial supplied into the coaxial socket (75Ω) marked FM on the rear of the system.

Follow the instructions given on Page 16 to tune into a radio station, and determine the best position for the aerial.

If reception is poor, you may need to install an outdoor aerial.

To do so, connect an outdoor FM aerial to the FM socket on the rear of the system using a 75Ω coaxial cable (not supplied).

1

Set the system to standby mode and disconnect it and the external source from the main socket.

2

Connect the audio cable to the rear of the micro component system.

3

Be sure to match connector colours.

Plug the system back into the main socket and press

POwER to switch it on.

4

Select the AUX source by pressing AUX.

Result: AUX is displayed.

5

6

Switch the external source on.

Adjust the volume and balance as required:

Volume Equalizer

Example: You can watch a film and take advantage of stereo sound provided that the original sound track is in stereo (as if you were in a cinema).

ENG

2

3

4

7

ENG

DEMO/DIMMER function Setting the Clock

All functions available on the system can be viewed on the display and the display's brightness can be switched between

"on" and "off".

1 Press the DEMO button.

Result: All functions available on the system appear on the front panel display.

Each of these are explained in detail in this guide. Please refer to the relevant section.

2

Press the DIMMER button.

Result: The Dimmer function is selected and the display darkens.

3

Press the DIMMER button once again to brighten the front panel display.

A display brightness control can only be performed while the system power is on.

1

5

6

1

2

3

Your system is equipped with a clock which allows you to turn your system on and off automatically.

You should set the clock:

When you first purchase the micro-compact system

After a power failure

After unplugging the unit

For each step, you have a few seconds to set the required

options. If you exceed this time, you must start again.

Switch the system on by pressing STANDby/ON.

Press TIMER/CLOCK twice.

Result: CLOCK is displayed.

Press PROGRAM/SET.

Result: The hour flashes.

4

7

To...

Increase the hours

Decrease the hours

Press the TUNING button

When the correct hour is displayed, press PROGRAM/SET.

Result: The minutes flash.

To...

Increase the minutes

Decrease the minutes

Press the TUNING button

When the correct time is displayed, press PROGRAM/SET.

Result: The clock starts and is displayed.

You can display the time, even when you are using another function, by pressing TIMER/CLOCK once.

You can also use , buttons on the main unit to instead of

TUNING button or in step 4, 6.

2,3

2

3,5,7

1

4,6

4,6

4,6

4,6

8

To play the CD/MP3/WMA-CD

You can play 12 cm or 8 cm compact disc without an adapter.

You can play 12 cm or 8 cm compact discs without an adapter.This unit has been designed to playback the CDs: Audio CD, CD-R,

CD-RW and MP3/WMA,-CD.

Continued use of irregular shape CDs (heart-shape, octagonal, etc.) can damage the unit.

3

4

5

1

2

6

Select the CD function by pressing PLAy/PAUSE( ) button.

Press the Open/Close( ) button.

Result: The compartment opens.

Place your disc in the compartment, with the label on the disc facingupwards.

Close the compartment by pressing the Open/Close( ) button again.

Press the PLAy/PAUSE( ) button.

Your CD Player will take a few moments to scan through all

the tracks recorded on a particular MP3/WMA-CD.

The English name of the song may be indicated on the display

only if directly downloaded from the PC or if the purchased MP3/

WMA-CD is sorted according to titles(directory).

(Other languages besides English may not be indicated.)

The English name of the track may not be indicated depending

on the characteristics of the MP3/WMA-CD.

Adjust the volume according to needs with the following procedures.

Press the VOLUME button of the main unit.

or

Press the VOLUME+or –button of the remote control. The volume level can be adjust in(VOL MIN,VOL 1- VOL 29,andVOL MAX).

7

8

Main set

To pause playback temporarily, press the PLAy/PAUSE(

Press PLAy/PAUSE(

) button.

) again to continue playing the disc.

Remote control

To pause playback temporarily, press the PAUSE( ) button.

Press PLAy( ) button to continue playing the disc.

Press the STOP( ) button when you have finished.

Press and hold OPEN/CLOSE( ) button for 5 seconds, ”LOCK”will be displayed and the compartment doesn’t open.In this way you must press and hold OPEN/CLOSE( ) button for along time until

“UNLOCK” will be displayed, the compartmentcan open.

8 2,4

1,5,7

6

Selecting a Track

You can select the track you wish to listen to when a disc is playing.

To play the previous track

Press the within 3 seconds after the current track started playing.

Press the twice 3 seconds after the current track started playing.

To play the next track

Press the .

To play the current track

Press the 3 seconds after the current track started playing.

To play the track of your choice

Press the or the appropriate number of times.

◆

You can also use the select a track.

or buttons on the remote control to

ENG

Searching for a Specific Music

Passage on a CD

When listening to a compact disc, you can quickly search for a specific music passage on a track.

To search through the tracks...

Forwards

Backwards

You can also press and hold down search through the tracks.

,

Press ...

on the main unit to auto

6

7

7

6

9

ENG

What is WMA?

WMA means Windows Media Audio, the global standard for audio signal compression technology.

What is MP3?

MP3 means MPEG1 Layer 3, the global standard for audio signal compression technology. It uses digital compression technology to compress original sound data by up to 12 times without sound quality degradation.

File Compatibility

The unit will playback files created in MP3 format (Mpeg1.

Layer3) with *.mp3 as their extension,and some WMA files with.WMA extension can’t be playback.

Playback will be impossible for the file of MP2 or 22KHz.

Function to skip through 10 tracks at a time

Press the +10 button briefly while playing back a

CD and MP3/WMA-CD . The track 10 tracks after the current one will then be played back.

Example: If you want to select track 43 during playback of track 5, press the +10 button four times, and then press the button three times .

5 10 20  30  40  41  42  43

How many MP3 files can a CD-R or CD-RW disc record?

The maximum capacity of one CD-R or CD-RW disc is

680MB.

Normally, one MP3 file has a capacity of 4MB, therefore approximately 170 files can be recorded on a single disc.

Regarding the playback of CD-R/RW

In the case of an original CD-R(Recordable) recorded in audio CD format, CD-RW(Rewritable) and editing by the user, playback is processed on the respective completed status. (The player may not be played back according to the characteristics of the CD or recorded status.)

The CD-RW is comparably less reflexive than CD which causes more time delay to read.

Remain Function

You can check the remaining time.

1

Press the REMAIN button .

◆

If you press the REMAIN button, the remaining time is displayed.

2

To cancel this function, press the REMAIN button again.

Display Function

(This function is not available during playback of an MP3/WMA-CD.)

You may check the total tracks of the disc.

1

Press the DISPLAy button.

Result: The total tracks numuber of the disc is displayed, and it will

disappear after 3 seconds.

10

Repeating One or All Tracks on the Compact Discs

You can repeat indefinitely:

A specific track on a compact disc.

All tracks on the compact disc selected.

1

Press REPEAT button.

Each time you press the REPEAT button, the repeat mode will change as follows:

MP3: RPT TRK ➝ RPT DIR ➝ RPT DISC ➝ RPT SHF ➝ RPT OFF.

CD: RPT TRK ➝ RPT DISC ➝ RPT SHF ➝ RPT OFF.

2

When you wish to stop the Repeat function, press REPEAT until

RPT OFF is displayed.

◆

RPT TRK: Repeatedly plays the selected track.

◆

RPT DIR: Repeatedly plays all tracks in the selected folder.

◆

RPT DISC: Repeatedly plays the entire disc.

◆

RPT SHF: one time.)

Plays tracks in random order.(Each track can be played

◆ RPT OFF: Cancels Repeat Playback.

Programming the Order of CD Playback

(This function is not available during playback of an MP3/WMA-CD.)

You can decide:

The order of the track desired to listen

The track not desired to listen

You can program up to 24 tracks.

You must stop the compact disc player before selecting the tracks.

1

2

If the CD function is selected, stop the player by pressing .


Result: The following indications are displayed:

(01 = Program no., -- -- = Track no. on the disc)

3

Select the required track by pressing the

Press the

Press the

or button:

button to move back through the tracks.

button to move forward through the tracks.

4

5

6

Press PROGRAM/SET to confirm your selection.

Result: The selection is stored and is displayed.

To select other tracks, repeat Steps 3 to 4.

Press PLAy ( ) to listen to the track selection in the order programmed.

7

When press button one time , compact disc player is stopped, and press button again to cancel the selection.

◆

If you open the compartment or turn off the power, the selection is cancelled.

ENG

1,2

A-B Repeat Playback

you can repeatedly play back a designated section of a CD/MP3/wMA-CD.

1 Press the REPEAT A-b button at the beginning of desired part.

'RPT A-' shows.

2

Press the REPEAT A-b button at the ending of desired part.

'RPT A-B' shows.

3

To cancel REPEAT A-B function, press REPEAT A-b button again.

Point B cannot be set until 5 seconds of playback has elapsed from point A.

3

1, 7 6

2,4

3

11

ENG

Checking or Changing Programmed

CD Tracks

You can check or change your selection of tracks at any time.

1

2

Press

/


Result: The following indications are displayed:

3

(CH = Check, 01=Program No., -- -- = Track No. on the disc)

If you have already programmed 24 tracks, CH is displayed instead of PR when you press PROGRAM/SET.

Press PROGRAM/SET once or more times until the track to be changed is displayed.

4

5

6

Press or button to select a different track.

Press PROGRAM/SET to confirm your change.

Press PLAy ( ) to start listening to the selection.

Result: The first track selected is played.

Please be aware of the following before using USb.

Some external USB storage devices may not be compatible with this

player.

With external HDD, FAT format can be played, however,the

NTFS format can not.

With USB 2.0 HDD, connect to a separate power source.

If it’s not connected to a separate power source, it may not work.

If memory of an external USB storage device is segmented into several parts, MP3 files of only the first hard disk drive can be played.

DRM applied files are not played.

Digital Rights Management: Technology and service that protect the

profit and rights of copyright owners by disallowing unauthorised use of

digital contents.

Even if the file name ends with .mp3, the file does not play if actual file format is MPEG layer 1 or 2.

Do not use a USB hub as it will not be recognized.

Up to 15 letters of MP3/WMA file name will be shown.

Delay

When selecting USB function,file reading (READ-IN) may take several minutes.

When playing a USB device,there may be a delay then advancing to the next track,especially with HDD.

The operation time of external USB storage devices will vary;even when

they are of the same capacity.

If the external USB storage device supports only USB VER1.1 and the access speed is slow,the file may not property.

2,3,5

4

1 6

4

1

Playing USb

you can play MP3/wMA files by connecting to various external USb storage devices such as USb flash memory or HDD(Hard Disc drives).

1

2

Connect the external USB storage device to your player.

Select USB function by pressing the USb button.

The first track of the first directory plays automatically.

To stop playing

Press the Stop ( ) button to stop playing.

Do not connect a USB charging device to the USB connection port on the player, because it may cause damage to the product.

2

12

To use high speed search

before you begin! Connect the external USB storage device to your player.

Select USB function by using the USB button.

you can search the desired section quickly during the play

Press the , button.

Whenever you press the button, you can search backward or forward quickly.

When you use the high speed search function, there is no sound.

To skip next 10 tracks



Press the +10 button on the remote control shortly during the play.

Example: If you want to select 43rd track while 15th track is playing, press the +10 button 3 times, and then press the button 3 times .

ENG

15  20  30  40  41  42  43

To repeat



Press REPEAT button.

Each time you press the REPEAT button, the repeat mode will change as follows:

RPT TRK ➝ RPT DIR ➝ RPT ALL ➝ RPT SHF ➝ RPT OFF.

When you wish to stop the Repeat function, press REPEAT until RPT

OFF is displayed.

◆

◆

RPT TRK:

◆

RPT DIR:

◆

◆

RPT ALL:

RPT SHF:

RPT OFF:

Repeatedly plays the selected track.

Repeatedly plays all tracks in the selected folder.

Repeatedly plays all tracks.

Plays tracks in random order. (Each track can be played one time.)

Cancels Repeat Playback.

To repeat section



1

Press the REPEAT A-b button at the beginning of desired part.

'RPT A-' shows.

2

Press the REPEAT A-b button at the ending of desired part.

'RPT A-B' shows.

3

To cancel REPEAT A-B function, press REPEAT A-b button again.

Point B cannot be set until 5 seconds of playback has elapsed from point A.

Remain Function

You can check the remaining time.



1

Press the REMAIN button .

◆ If you press the REMAIN button, the remaining time is displayed.

2

To cancel this function, press the REMAIN button again.

Selecting a Track from USb Device

you can select an MP3 file during the play.


Select the USB function by using the USB button.

If you want to move the next/previous(track), press the button shortly.

It moves the next/previous file within the directory.

,

If you press the , button more times than the number of the files in the directory, it will move over to the next directory.

13

ENG

About RDS broadcasting

This unit has the RDS (Radio Data System) function, which enables for the various information such as broadcasting station, radio text, time and 30 types of programs (News, Rock, Classic, etc.) to be received from the FM RDS station together with normal radio signal.

Press the ( ) button.

Receive the FM radio.

See the radio receiving method on the page 16.

FM and frequency are shown on the display

3

Press the RDS DISPLAy button to select the desired RDS mode.

Whenever the button is pressed, RDS mode changes as follows.

PS NAME RT CT Current FM frequency

The RDS function is available only in FM broadcasting.

RDS may not operate correctly if the station tuned is not transmitting RDS signal property or if the signal strength is weak.

Description on RDS function

1. PTy(Program Type) : Displays the type of programme

currently being broadcast .

2. PS NAME(Program Service Name) : Indicates the name of broadcasting station and is composed of 8 characters.

3. RT(Radio Text) : Decodes the text broadcast by a station (if any) and is composed of maximum 64 characters.

4. CT(Clock Time) : Decodes the real time clock from the FM frequency.

Some stations may not transmit PTY, RT or CT information therefore this may not be displayed in all cases.

5. TA(Traffic Announcement) : When this symbol flashes it shows that the traffic announcement is in progress.

About RDS DISPLAy function

About "PS NAME" MODE

Displays the name of broadcasting station.

Press the RDS DISPLAy button to select the PS NAME.

" PS NAME" appears on the display.

If the PS information is being received, the PS name (BBC, AFO, NDR, etc.) is shown on the display.

If the PS information isn't received, the original FM frequency is shown.

Even though no RDS DISPLAy button is pressed, the reception of

PS information ensues the PS name is displayed.

About 'RT' MODE

Displays the character transmitted from the broadcasting station.

Press the RDS DISPLAy button to select the RT MODE.

" RT" appears on the display.

If the RT information is being received, the received information is shown on the display.

If the RT information isn't received, the " NO RT" is shown on the display.

About CT(Clock Time)

Sets the time of RDS clock.

To select the CT time, set the RDS DISPLAy button to CT MODE.

The CT information will take up to 2 minutes to be decoded therefore the clock isn’t displayed immediately.

If there is no received CT information, " NO CT" is displayed.

1

3

14

PTy(Program Type) indication and

PTy-SEARCH function

NEwS

Display

AFFAIRS

INFO vARIED

POP M

ROCK M

M.O.R.M

LIGHT M

SPORT

EDUCATE

DRAMA

CULTURE

SCIENCE

CLASSICS

OTHER M wEATHER

FINANCE

CHILDREN

SOCIAL

RELIGION

PHONE IN

TRAvEL

LEISURE

JAZZ

COUNTRy

NATION M

OLDIES

FOLK M

DOCUMENT

TEST

 The PTY information is composed of an identification symbol, which helps the FM radio to recognize the program type of each FM station.

 The below 30 PTY information is shown on the display by pressing the

RDS PTY button.

 To stop searching any time during the process, press TUNING MODE

while searching.

 There is a time limit in doing the followings steps.If the setting is cancelled before you finish,start from step 1 again.

 When pressing the buttons on the primary remote control,make sure that

you have selected the FM station using the primary remote control.

• Weather

• Finance

• Children’s programmes

• Social affairs

• Religion

• Phone in

• Travel

• Leisure

• Jazz Music

• Country Music

• National Music

• Oldies Music

• Folk Music

• Documentary

• Alarm Test

Program Type

• News including an announced opinion and report

• Several matters including a current incident, documentary, discussion and analysis.

• Information including weights and measures, returns and forecast, matters interesting the customer, medical information, etc.

• Sports

• Education

• Drama-Radio serial, etc.

• Culture-National or local culture including the religious problem, social science, language, theatre,etc.

• Natural science and technology

• Others-Speech, amusing program (quiz, game), interview, comedy and satirical play, etc.

• Pop music

• Rock music

• M.O.R- Comfortable music, occasionally vocal or piece

• Light classical music- Classical music and instrumental and chorus music

• Heavy classical music-Orchestra music, symphony, chamber music and opera

• Other music - Jazz, R&B country music

About PTy-SEARCH

1

2

Receive the FM radio.

See the radio receiving method on the page 16.

The FM and frequency appear on the display.

Press the RDS PTy button.

The PTY MODE(NEWS, AFFAIRS, etc.) appears on the display.

Press the TUNING or button to select the desired PTY

MODE.

If the station is transmitting no PTY information, 'NO PTY' lights on the display.

When the PTY MODE is selected(The PTY MODE is shown on the display), press the PTY KEY once again to convert into PTY-

SEARCH MODE and auto-search the station sequentially.

If the PTY MODE received in the course of auto-search agrees with the selected PTY MODE, the auto-search stops and the PTY-

SEARCH is finished.

If the PTY MODE which agrees with the PTY MODE selected in the course of auto-search, isn't received, it is returned to the first frequency at beginning the PTY SEARCH and the auto-search and

PTY SEARCH are suspended.

2

2

2

15

ENG

ENG

Searching for and Storing the Radio

Stations

You can store up to:

15 FM stations

1

2


3

Select the TUNER function by pressing TUNER.

To search for a Press TUNING MODE button station...

Preset Once or more times until PRESET is

displayed.

Automatically Once or more times until AUTO is displayed.

Manually Once or more times until MANUAL is

displayed.

4

Select the station to be stored by:

Pressing TUNING or on the remote control.

To scroll through the frequencies faster when searching manually, hold down the or buttons.

The automatic search procedure may stop on a frequency that does not correspond to a radio station. If this happens, use the manual search mode.

5

Adjust the volume by:

Press the vOLUME button on the main unit or

Pressing the vOLUME + or – buttons on the remote control

6

7

Select the FM stereo or mono mode by pressing MO/ST.

If you do not want to store the radio station found, revert to Step 3 and search for another station.

Otherwise:

a Press PROGRAM/SET.

b Press or on the main unit or press TUNING

or on the remote control to assign a program number .

c Press PROGRAM/SET to store the radio station.

8

To store any other radio frequencies required, repeat Steps 3 to 7.

In Tuner mode

In manual tuning mode, you can use , button on the main unit to manual search a radio station.

During Tuner auto searching, press button on the main unit or

TUNING MODE button on the remote control to stop auto searching.

In Preset tuning mode, you can use , button on the main unit to search a stored radio station.

1

4,7 3 4,7

2

3 6

4,7

5 4,7 5

5

16

Selecting a Stored Station

You can listen to a stored radio station as follows:

1

2

3


Select the TUNER function by pressing TUNER.

Press the TUNING MODE button on the remote control or on the main unit until “PRESET” is displayed.

4

Press or

or to select the desired station.

Select the desired station by pressing the

TUNING or button on the remote control.

Result: The desired station is now received.

Improving Radio Reception

you can improve the quality of radio reception by:

Rotating the FM aerial

Testing the positions of the FM aerials before fixing them permanently

If reception from a specific FM radio station is poor, press MO/ST. to switch from stereo mode to mono. The quality of the sound will be improved.

ENG

1 4 3 4

2

3

4

4

17

ENG

CD RIPPING Function

you can rip a compact disc as a MP3 file on the USb

This feature enables you to ripping with the start of the disc or track of your choice.

1

2

3

4

5


Connect the USB.

Load a compact disc(Digital Audio).

Press the OPEN/CLOSE button to open the CD door.

Insert a CD and press the OPEN/CLOSE button to close the CD door.

Use the CD selection ( song.

or ) buttons to select the desired

Press CD RIPPING button on remote control to starting ripping.

If the system is playing state, press this button, “TRACK RIPPING”

is displayed and CD RIPPING starts.

If the system is playing state, press and hold this button, “FULL CD

RIPPING” is displayed and CD RIPPING starts.

During CD ripping, do not disconnect USB device.

To stop ripping, press STOP( )button and then automatically create and save as the MP3 file.

After CD-Ripping, a directory named “RIPPING” will be created in your device, and the file name is same with the disc.

Note

◆ Don’t disconnected USB and AC Cord during CD-Ripping. This may cause the file damage. If you want to stop CD-Ripping during

CD-Ripping, you must press stop Key first and after the CD Stopped, then you can remove the USB device.

◆

If you disconnected USB device when CD Ripping, the main unit will be power off and you may not delete the ripped file,In this case, please connect the USB on the PC and backup the USB data on the PC first and then formate the USB device.

◆ When the USB memory is not enough, it will be displayed “RIPPING

ERROR”.

◆

DTS-CD can’t for CD Ripping.

◆ With external HDD, FAT format the USB can be CD Ripping, but not

NTFS. The CD Ripping function of this product does not support all USB devices.

◆

When you use CD high speed search function or in the Pause or Stop mode, the CD Ripping can’t work.

◆ During CD Ripping, do not deal impact.If is shocked while CD Ripping,

CD Ripping maybe disengage.

◆

Sometimes, some of USB devices, CD Ripping time is long.

◆ In program mode, you can't use CD RIPPING function.

1

4

3 5 3 3

18

Timer Function

The timer enables you to switch the system on or off at specific times.

Example: You wish to wake up to music every morning.

If you no longer want the system to be switched on or off automatically, you must cancel the timer.

Before setting the timer, check that the current time is correct.

For each step, you have a few seconds to set the required options. If you exceed this time, you must start again.

1

2

3


Press TIMER/CLOCK until TIMER is displayed.


Result: ON TIME is displayed for a few seconds, followed by any switch-on time already set; you can set the timer switch-on time.

4

Set the timer switch-on time.

a Press the TUNING or buttons.

b Press PROGRAM/SET.


c Press the TUNING or buttons.

d Press PROGRAM/SET.

Result: OFF TIME is displayed for a few seconds, followed by any switch-off time already set, you can now set the timer switch-off time.

5

Set the timer switch-off time.

a Press the TUNING or buttons.

b Press PROGRAM/SET.


c Press the TUNING or buttons.

d Press PROGRAM/SET.

Result: VOL XX is displayed, where XX corresponds to the volume already set.

6

Press TUNING or to adjust the volume level and press

PROGRAM/SET.

Result: The source to be selected is displayed.

7

Press the TUNING or buttons to select the source to be played when the system switches on.

If you select...

TUNER (radio)

CD (compact disc)

USB you must also...

a Press PROGRAM/SET.

b Select a preset station by press

the TUNING or buttons.

Load disc.

connect usb.

8

Press PROGRAM/SET to confirm the timer.

1,9 4,5,6,7

2

4,5,6,7

4,5,6,7

4,5,6,7

3,4,5,6,7,8

Cancelling the Timer

After having set the timer, it will start automatically as shown by the TIMER indication on the display. If you no longer wish to use the timer, you must cancel it.

REC

REC

To...

Cancel the timer

Restart the timer

Once.

NR

Twice.

Result: is displayed again.

¡ If the timer switch on and off times are identical, the word is displayed.

ERROR

¡ You may use , buttons on the main unit to instead of the

TUNING or buttons to adjust in step 4, 5, 6, 7.

ENG

19

Mute Function

ENG

You can turn the sound off temporarily on your system.

Example: You wish to answer a telephone call.

1

2

Press MUTE.

To switch the sound back on , press MUTE again or the vOLUME buttons.

Bass Level Function

BASS function stresses low tones providing thudding sound effects.

1

Press TREB/BASS button until BASS 00 is displayed. Press or

button to select from BASS -04 to BASS 04.

2

You can select the level of low tones you desire.

Power Sound Function

Selecting EQ Mode

Your micro-compact system is equipped with a preset equalizer that allows you to choose the most appropriate balance between treble and bass frequencies, according to the type of music you are listening to.

To obtain a...

Normal balance (linear)

Balance suitable for pop music

Balance suitable for rock music

Balance suitable for classic music

Balance suitable for jazz

Balance suitable for super bass

Select...

PASS

POP

ROCK

CLASSIC

JAZZ

S.BASS

Your compact system is equipped with the function of

PowerSound.

The function of Power Sound amplifies bass and improves highkey or bass twice as much for you to appreciate powerful realsound.

1

2

Press the P.SOUND button.

Result: “ P.SOUND” is displayed.

To cancel this function, press P.SOUND again, “OFF” is displayed for a few seconds.

Treble Level Function

Treble Control function stresses high tones providing thudding soundeffects.

1

PressTREB/BASS button until TREB 00 is displayed. Press or

button to select from TREB -04 to TREB 04.

2

You can select the level of high tones you desire.

Power Bass Function

Y our micro-compact system has a bass amplification function called SBS (Super Bass Sound). This function makes the sound more powerful and real.

1

Press the P.bASS button.

Result: “ P. bASS” is displayed.

2

To cancel this function, press P.bASS again, “OFF” is displayed for a few seconds.

20

Setting the System to Switch off

Automatically

While listening to music, you can set the system to switch off automatically.

Example: You wish to go to sleep to music.

1

2

Press SLEEP.

Result: playback starts and the following indications are displayed:

90 MIN

Press SLEEP once or more times to indicate how long the system should continue playing before it switches off:

Connecting Headphones

You can connect a set of headphones to your micro-compact system so that you can listen to music or radio programmers without disturbing other people in the room. The headphones must have a 3.5

ø jack or an appropriate adapter.

Connect the headphones to the PHONES jack on the main unit.

Result: The loudspeakers are no longer used to output the sound.

Prolonged use of headphones at a high volume may damage your hearing.

ENG

At any time, you can:

Check the remaining time by pressing SLEEP

Change the remaining time by repeating Steps 1 and 2

3

To cancel SLEEP function, press SLEEP once or more times until SLEEPOFF is display.

21

ENG

Safety Precautions

The following diagrams illustrate the precautions to be taken when using or moving your micro-compact system.

Ambient operating conditions:

Ambient temperature 5°C-35°C

Humidity 10-75%

Do not expose the unit to direct sun radiation or other heat sources.

This could lead to overheating and malfunction of the unit.

Do not place potted plants or vases on top of the unit. Moisture entering the unit could lead to dangerous electric shock and can cause equipment damage. In such events immediately disconnect the main plug from the socket.

During thunderstorms, disconnect the main plug from the socket.

Main voltage peaks due to lightning could damage the unit.

Cleaning Your Micro-Compact

System

To obtain the best possible results from your micro-compact system, you must clean the following elements regularly:

The outer casing

The compact disc player

The cassette players (heads, rollers and drive capstans)

Always unplug the system from the wall outlet:

Before cleaning it

If you are not going to be using it for a long time

Outer Casing

Clean the outer casing regularly using a soft cloth and a light detergent. Do not use abrasive powders, liquids or aerosol cleaners. Never let any liquids get into the system.

Compact Disc Player

1

Before playing a compact disc, clean it with a special CD cleaning agent. Do not use the same cleaning agents as for vinyl LP records.

Carefully wipe the disc from the centre outward.

2

Regularly clean the player with a special cleaning disc (available from your local dealer).

If you will not be using the remote control for a long time, remove the batteries to prevent corrosion.

Although your system is very hard-wearing, it should not be used in an excessively dusty environment or subjected to shocks or extreme heat (close to heating appliances or in direct sunlight, etc.).

If the unit emits an unpleasant odor when in use, unplug it from the main supply and contact the after-sales service.

UP vOLUME

DOwN

Remove the batteries from the remote control, if not used for any extended period.

Leaking batteries can cause serious damage to the remote control.

When using headphones, take care not to listen at excessive volumes.

Extended use of headphones at high volumes will lead to hearing damage.

Precautions When Using Compact

Discs

Handle your compact discs with care. Always hold them by the edges to avoid leaving fingerprints on the shiny surface.

When you have finished playing a compact disc, always put it back in its case.

Do not fix paper or adhesive tape to the discs and do not write on the label.

Clean them with a special-purpose cloth.

Store your compact discs in a clean place, out of direct sunlight, where they will not be exposed to high temperatures.

DIGITAL AUDIO

Do not place heavy items on the main lead. Main cable damage can lead to damage of the equipment (fire hazard) and can cause electric shock.

Do not remove any equipment panels.

The inside of the unit contains live components, which cause electric shock.

22

Before Contacting the After-Sales Service

It always takes a little time to become familiar with a new appliance.

If you have any of the problems listed below, try the solutions given. They may save you the time and inconvenience of an unnecessary service call.

If the above guidelines do not allow you to solve the problem, take a note of:

The model and serial numbers, normally printed on the rear of the system

Your warranty details

A clear description of the problem

Then contact your local dealer or SAMSUNG after-sales service.

Problem

The system does not work

R

A

L

N

E

G

E

There is no sound

The Timer does not work

In case it does not work, even the action is taken as above.

CD

/

MP3

I

CD

The compact disc player does not start playing

Checks/Explanation

• The main lead is not correctly plugged into a wall socket or the wall socket is not switched on.

• The remote control batteries need replacing or the polarity has not been respected.

• The STANDBY/ON button has not been pressed.

• The volume has been completely turned down.

• The correct function (TUNER, CD, USB, AUX) has not been selected.

• You have connected a set of earphones.

• The loudspeaker wires have been disconnected.

• The MUTe button has been pressed.

• The timer has been stopped by pressing TIMeR ON/OFF.

• Press the STOP button for 5 seconds in power ‘OFF’(standby), then it is returned the original position (RESET)

• The CD function has not been selected.

• The disc has been inserted face down or is either dirty or scratched.

• The laser sensor is dirty or dusty.

• The system has not been installed on a flat, horizontal surface.

• Condensation has formed in the player; leave the system in a warm, airy room for at least one hour.

D

I

R

A

O

Reception is poor or no radio stations are received at all

• The TUNeR function has not been selected.

• The radio frequency has not been correctly selected.

• The aerial has been disconnected or is not facing the right way. Turn it until you find the best orientation.

• You are in a building that blocks radio waves; you must use an outside aerial.

ENG

23

Technical Specifications

ENG

SAMSUNG strives to improve its products at all times. Both the design specifications and these user instructions are thus subject to change without notice.

RADIO

FM

Signal/noise ratio

Usable sensitivity

Total harmonic distortion

62 dB

10 dB

0.4 %

COMPACT DISC PLAYER

Capacity

Frequency range

Signal/noise ratio

Distortion

Channel separation

Disc sizes

AMPLIFIER

Output power

Front Speaker (4 Ω)

Channel separation

Signal/noise ratio

1 disc

20 Hz - 20 KHz (± 1 dB)

90 dB (at 1 KHz) with filter

0.1 % (at 1 KHz)

75 dB

Diameter: 120 or 80 mm. Thickness: 1.2 mm

60 Watts/CH RMS,IEC (total harmonic distortion: 10 %)

60 dB

70 dB

GENERAL

Power Consumption

Dimensions

Weight

35W

230 (W) x 154 (H) x 251 (D) mm

2.2 Kg

24

Contact SAMSUNG wORLD wIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre.

Region Country Customer Care Centre web Site

ENG

25

AH68-02157B

No results