Data Projector

Operating Instructions

3-293-838-11 (1)

VPL-EW5

VPL-EX50/EX5

VPL-ES5

© 2008 Sony Corporation

WARNING

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

WARNING

THIS APPARATUS MUST BE

EARTHED.

IMPORTANT

The nameplate is located on the bottom.

WARNING

When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring, or connect the power plug to an easily accessible socket-outlet near the unit.

If a fault should occur during operation of the unit, operate the disconnect device to switch the power supply off, or disconnect the power plug.

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer’s instructions.

For the customers in the U.S.A.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

2

WARNING determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/

TV technician for help.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

All interface cables used to connect peripherals must be shielded in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC

Rules.

If you have any questions about this product, you may call:

Sony Customer Information Service Center

1-800-222-7669 or http://www.sony.com/

Declaration of Conformity

Trade Name: SONY

Model: VPL-EW5, VPL-EX50,VPL-

EX5, VPL-ES5

Responsible Party: Sony Electronics Inc.

Address: 16530 Via Esprillo,

San Diego, CA 92127 U.S.A.

Telephone Number: 858-942-2230

This device complies with part 15 of the

FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

WARNING: THIS WARNING IS

APPLICABLE FOR USA ONLY.

If used in USA, use the UL LISTED power cord specified below.

DO NOT USE ANY OTHER POWER

CORD.

Plug Cap Parallel blade with ground pin

(NEMA 5-15P Configuration)

Cord Type SJT, three 16 or 18 AWG wires

Length Minimum 1.5m (4 ft .11in.), Less than 4.5 m (14 ft .9

5

/

8

in.)

Rating Minimum 10A, 125V

Using this unit at a voltage other than 120V may require the use of a different line cord or attachment plug, or both.

To reduce the risk of fire or electric shock, refer servicing to qualified service personnel.

WARNING: THIS WARNING IS

APPLICABLE FOR OTHER

COUNTRIES.

1. Use the approved Power Cord (3-core mains lead) / Appliance Connector / Plug with earthing-contacts that conforms to the safety regulations of each country if applicable.

2. Use the Power Cord (3-core mains lead) /

Appliance Connector / Plug conforming to the proper ratings (Voltage, Ampere).

If you have questions on the use of the above

Power Cord /Appliance Connector /Plug, please consult a qualified service personnel.

For the customers in Europe

The manufacturer of this product is Sony

Corporation, 1-7-1 Konan, Minato-ku,

Tokyo, Japan.

The Authorized Representative for EMC and product safety is Sony Deutschland

GmbH, Hedelfinger Strasse 61, 70327

Stuttgart, Germany. For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents.

For the State of California, USA only

Perchlorate Material - special handling may apply, See www.dtsc. ca.gov/hazardouswaste/ perchlorate

Perchlorate Material: Lithium battery contains perchlorate.

Disposal of the used lamp

For the customers in the USA

Lamp in this product contains mercury.

Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the

Electronic Industries Alliance

(www.eiae.org).

Disposal of Old Electrical &

Electronic Equipment (Applicable in the European Union and other

European countries with separate collection systems)

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

For the customers in Taiwan only

WARNING

3

Table of Contents

Precautions ......................................... 5

Notes on Installation and Usage ........ 6

Overview

Features .............................................. 9

Location and Function of Controls .. 10

Top/Right Side/Front .................. 10

Rear/Bottom ............................... 10

Control Panel .............................. 12

Connector Panel ......................... 14

Remote Commander ................... 15

About the Preset Memory No. ....34

The SET SETTING Menu ................35

The MENU SETTING Menu ...........37

The INSTALL SETTING Menu .......38

The INFORMATION Menu .............40

Maintenance

Replacing the Lamp ..........................42

Cleaning the Air Filter ......................44

Projecting the Picture

Installing the Projector ..................... 17

Connecting the Projector ................. 19

Connecting a Computer .............. 19

Connecting a VCR ..................... 21

Projecting ......................................... 22

Turning Off the Power ..................... 24

Others

Troubleshooting ................................45

Messages List ..............................47

Specifications ...................................49

Installation Diagram .........................54

Floor Installation (Front Projection)

..................................................54

Ceiling Installation (Front

Projection) ...............................56

Dimensions .......................................58

Index .................................................60

Convenient Functions

Selecting the Menu Language .......... 25

Security Lock ................................... 26

Other Functions ................................ 27

Direct Power On/Off Function ... 27

Off & Go Function ..................... 27

Effective Tools for Your

Presentation ............................. 27

Adjustments and Settings

Using a Menu

Using a MENU ................................ 29

The PICTURE SETTING Menu ...... 31

The INPUT SETTING Menu .......... 33

4

Table of Contents

Precautions

Safety

• Check that the operating voltage of your unit is identical with the voltage of your local power supply. If voltage adaptation is required, consult with qualified Sony personnel.

• Should any liquid or solid object fall into the cabinet, unplug the unit and have it checked by qualified personnel before operating it further.

• Unplug the unit from the wall outlet if it is not to be used for several days.

• To disconnect the cord, pull it out by the plug. Never pull the cord itself.

• The wall outlet should be near the unit and easily accessible.

• The unit is not disconnected to the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off.

• Do not look into the lens while the lamp is on.

• Do not place your hand or objects near the ventilation holes. The air coming out is hot.

• Be careful not to get your fingers caught in the adjuster.

• Do not spread a cloth or paper under the unit.

Illumination

• To obtain the best picture, the front of the screen should not be exposed to direct lighting or sunlight.

• Ceiling-mounted spot lighting is recommended. Use a cover over fluorescent lamps to avoid lowering the contrast ratio.

• Cover any windows that face the screen with opaque draperies.

• It is desirable to install the unit in a room where floor and walls are not of lightreflecting material. If the floor and walls are of reflecting material, it is recommended that the carpet and wall paper be changed to a dark color.

Preventing internal heat build-up

The unit is equipped with ventilation holes

(intake) and ventilation holes (exhaust). Do not block or place anything near these holes, or internal heat build-up may occur, causing picture degradation or damage to the projector.

Cleaning

Before cleaning

Be sure to disconnect the AC power cord from the AC outlet.

Cleaning the air filter

• Clean the air filter whenever you replace the lamp.

• Refer to the “Cleaning the Air Filter” on

page 44 for the air filter cleaning.

Cleaning the lens

The lens surface is especially treated to reduce reflection of light.

As incorrect maintenance may impair the performance of the projector, take care with respect to the following:

• Avoid touching the lens. To remove dust on the lens, use a soft dry cloth. Do not use a damp cloth, detergent solution, or thinner.

• Wipe the lens gently with a soft cloth such as a cleaning cloth or glass cleaning cloth.

• Stubborn stains may be removed with a soft cloth such as a cleaning cloth or glass cleaning cloth lightly dampened with water.

• Never use solvent such as alcohol, benzene or thinner, or acid, alkaline or abrasive detergent, or chemical cleaning cloth, as they will damage the lens surface.

Cleaning the cabinet

• Clean the cabinet gently with a soft dry cloth. Stubborn stains may be removed with a cloth lightly dampened with mild detergent solution, followed by wiping with a soft dry cloth.

• Use of alcohol, benzene, thinner or insecticide may damage the finish of the cabinet or remove the indications on the cabinet. Do not use these chemicals.

Precautions

5

• If you rub on the cabinet with a stained cloth, the cabinet may be scratched.

• If the cabinet is in contact with a rubber or vinyl resin product for a long period of time, the finish of the cabinet may deteriorate or the coating may come off.

LCD data projector

• This LCD data projector is manufactured using high-precision technology. You may, however, see tiny black points and/or bright points (red, blue, or green) that appear continuously on the LCD data projector. This is a normal result of the manufacturing process and does not indicate a malfunction.

Notes on Installation and Usage

Unsuitable Installation

Do not install the projector in the following situations. Installation is these situations

or locations may cause a malfunction or

damage to the unit.

Poorly ventilated locations

• Allow adequate air circulation to prevent internal heat build-up. Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation holes. When internal heat builds up due to blockage of ventilation holes, the temperature sensor will function, and the power will be turned off automatically.

• Leave space of more than 30 cm (11

7

/

8 inches) around the unit.

• Be careful not to allow the ventilation holes to inhale tiny objects such as pieces of paper or clumps of dust.

6

Notes on Installation and Usage

Hot and humid Very dusty, extremely smoky locations

• Avoid installing the unit in a location where the temperature or humidity is very high, or the temperature is very low.

• To avoid moisture condensation, do not install the unit in a location where the temperature may rise rapidly.

Locations subject to direct cool or warm air from an air-conditioner

Installing the projector in such a location may cause a malfunction of the unit due to moisture condensation or a rise in temperature.

Near a heat or smoke sensor

Avoid installing the unit in a very dusty or extremely smoky environment. Otherwise, the air filter will become obstructed, and this may cause a malfunction of the unit or damage it. Dust preventing the air passing through the filter may cause a rise in the internal temperature of the unit. Clean the air filter whenever you replace the lamp.

Unsuitable Conditions

Do not use the projector under the following conditions.

Do not stand the unit upright on one side

Avoid using the unit standing upright on its side. It may cause malfunction.

Malfunction of the sensor may occur.

Do not tilt the unit to the right or left

Avoid tilting the unit to an angle of 15°, and avoid installing the unit in any way other than placing it on a level surface or suspending from the ceiling. Such an installation may cause color shading or shorten the lamp life excessively.

Notes on Installation and Usage

7

Do not block the ventilation holes

Avoid using a thick-piled carpet or anything that covers the ventilation holes (exhaust/ intake); otherwise, internal heat may build up.

Do not place a blocking object just in front of the lens

Do not place any object just in front of the lens that may block the light during projection. Heat from the light may damage the object. Use the PIC MUTING key to cut off the picture.

Do not use the Security bar for transporting or installation

Usage at High Altitude

When using the projector at an altitude of

1,500 m or higher, turn on “High

Altitude Mode” in the INSTALL SETTING menu. Failing to set this mode when using the projector at high altitudes could have adverse effects, such as reducing the reliability of certain components.

Notes on Use

Note on carrying the projector

The unit is manufactured using highprecision technology. When transporting the unit stored in the carrying case, do not drop the unit or subject it to shock, as this may cause damage. When storing the unit in the carrying case, disconnect the AC power cord and all other connecting cables or cards, and store the supplied accessories in a pocket of the carrying case.

Note on the screen

When using a screen with an uneven surface, a striped pattern may rarely appear on the screen depending on the distance between the screen and the projector or the zooming magnification settings used. This is not a malfunction of the projector.

Use the Security bar at the rear of the projector for a purpose of preventing theft, by attaching a commercially available theft prevention cable for example. If you lift the projector by holding the Security bar, or hang the projector by using this bar, it may cause the projector to fall or be damaged.

8

Notes on Installation and Usage

B Overview

Features

High brightness · High picture performance

High brightness

Sony’s unique optical system allows high efficiency.

High picture performance

VPL-EW5: Three super-high-aperture

0.59-inch WXGA panels with approximately 1,020,000 effective pixels produce a resolution of 1280 × 800 dots

(horizontal/vertical) for RGB input, and

750 horizontal TV lines for video input.

VPL-EX50/EX5:Three super-high-aperture

0.63-inch XGA panels with approximately 790,000 effective pixels produce a resolution of 1024 × 768 dots

(horizontal/vertical) for RGB input, and

750 horizontal TV lines for video input.

VPL-ES5:Three super-high-aperture 0.63inch SVGA panels with approximately

480,000 effective pixels produce a resolution of 800 × 600 dots (horizontal/ vertical) for RGB input, and 500 horizontal TV lines for video input.

Direct Power On/Power Off function

The AC power for the entire system can be turned on and off by means of a breaker or other switch without going through a standby mode.

Simple maintenance

Even when the projector is mounted on the ceiling, you can clean the air filter easily because it is located at the side.

Clean the filter at the same time as you replace the lamp.

Short focal lens

The projection distance is very short, approximately 2.4 m (7.9 feet), when projecting an 80-inch image, which allows projection on a larger screen even in a limited space.

Security Functions

Security lock

This function makes it possible to prevent projection of a picture on the screen unless the required password is entered when the projector is turned on.

Panel key lock

This function locks all the keys on the control panel of the projector, allowing use of the keys on the Remote Commander. This prevents the projector from operating incorrectly.

Other Convenient Functions

• Low fan noise makes your presentation comfortable

• On-screen menu in 17 languages

• Picture muting

• Freeze

• Lamp mode switching function (VPL-

EX50/EW5 only)

• Low power consumption in standby

• Security bar

About Trademarks

• Adobe Acrobat is a trademark of Adobe

Systems Incorporated.

• Windows is a registered trademark of

Microsoft Corporation in the United States and/or other countries.

• Kensington is a registered trademark of

Kensington Technology Group.

• Macintosh is a registered trademark of

Apple, Inc.

• VESA is a registered trademark of the

Video Electronics Standards Association.

• Display Data Channel is a trademark of the

Video Electronics Standards Association.

• HDMI, HDMI logo and High-Definition

Multimedia Interface are trademarks or registered trademarks of HDMI Licensing

LLC.

• All other trademarks and registered trademarks are trademarks or registered trademarks of their respective holders. In this manual, ™ and ® marks are not specified.

Features

9

Location and Function of Controls

Top/Right Side/Front

4

1

2

3

Rear/Bottom

5

6 qa qs qd qf qg qh

7 8

10

Location and Function of Controls

9 0

a Ventilation holes (exhaust) b Lens

Remove the lens cover before projection.

c Front remote control detector d Control panel

For details, see “Control Panel” on page 12.

e Zoom ring

Adjusts the picture size.

f Focus ring

Adjusts the picture focus.

g Ventilation holes (intake)/Air

filter cover

h Adjusters (fore pad) i Lamp cover j Adjuster k Connector Panel

For details, see “Connector Panel” on page 14.

l AC IN socket

Connects the supplied AC power cord.

m Adjuster adjustment button

For details, see “Using the adjuster” on page 23.

n Speaker o Security bar

An anti-theft chain or wire

(commercially available) can be connected to it.

Security bar p Security lock

Connects to an optional security cable

(from Kensington).

Web page address: http://www.kensington.com/

Note

To maintain optimal performance, clean the

air filter whenever you replace the lam p

.

For details, see “Cleaning the Air Filter” on page 44.

Location and Function of Controls

11

Control Panel

1 2 3 4 5 6 a ?/1

(On/Standby) key

Turns on the projector when the projector is in standby mode. To turn off the power, press the ?/1 key twice according to the message or hold the ?/1 key for about one second.

Lights up or flashes under the following conditions:

– Lights in red when the AC power cord is plugged into a wall outlet. Once the projector is in standby mode, you can turn it on with the ?/1 key.

– Flashes in red when the temperature becomes high inside the projector, or when the projector fails to operate.

– Lights in green when the power is turned on, and when it is ready to operate.

– Flashes in green from the projector is turned on until the projector is ready to operate. Also, flashes in green while the cooling fan is running after the power is turned off with the ?/1 key.

The fan runs for about 90 seconds after the power is turned off.

– Lights in orange when the power saving mode is on.

For detail, see page 24.

b INPUT key

Selects an input signal. The input signal will change whenever you press the key.

c ENTER/

V

/

v

/

B

/

b

(Arrow) keys

Used to enter the settings of items in the menu system, select a menu, or make various adjustments.

d LAMP/COVER indicators

Flashes in orange under the following conditions:

• A reception rate of 2 flashes when the lamp cover or air filter cover is not secured firmly.

• A reception rate of 3 flashes when the lamp has reached the end of its life or reaches a high temperature.

12

Location and Function of Controls

e MENU key

Displays the on-screen menu. Press again to clear the menu.

f PIC MUTING key

Cuts off the picture. Press again to restore the picture.

Location and Function of Controls

13

Connector Panel

VPL-EW5

1 2 8 6 5 7

VPL-EX50

1 4 2 5 8 6 7

VPL-EX5

1 3 2 8 6 7

VPL-ES5

1 2 3 8 6 a VIDEO IN connector

• S VIDEO (mini DIN 4-pin):

Connects to the S video output of video equipment.

• VIDEO (phone type):

Connects to the video output of video equipment.

• AUDIO (stereo minijack) (VPL-

EW5/EX50 only):

To listen to sound output from video equipment, connect via this jack to the audio output of the video equipment.

b INPUT A connector

• RGB (HD D-sub 15-pin, female):

Inputs a computer signal, video GBR signal, component signal, or DTV signal depending on the connected equipment.

Connects to the output connector of equipment using the supplied cable or an optional cable.

• AUDIO (stereo minijack) (VPL-

EW5 only):

To listen to sound output from computer, connect via this jack to the audio output of the computer.

14

Location and Function of Controls

For details, see “Connecting a

Computer” on page 19 and

“Connecting a VCR” on page 21.

c INPUT A/VIDEO IN AUDIO

connector (VPL-EX5/ES5 only)

Inputs audio signal attached to the image from INPUT A or VIDEO.

d INPUT A/ B AUDIO (VPL-EX50

only)

Inputs audio signal attached to the image from INPUT A or INPUT B.

e INPUT B connector

• Digital RGB/Component connector

(for HDMI and HDCP) (VPL-EW5 only):

Connects to the video output connector of the video equipment or the computer equipped with HDMI/

DVI output connector (digital).

• RGB connector (HD D-sub 15-pin,

female) (VPL-EX50 only):

Inputs a computer signal.

Connects to the output connector of equipment using the supplied cable or an optional cable.

f OUTPUT connector

• MONITOR (HDD-sub 15-pin

female):

Connects to the input connector of the monitor. Only the computer signal on the current channel is output from among the signals connected to

INPUT A or INPUT B (VPL-EX50 only).

• AUDIO (stereo minijack):

Connects to the active speaker. Adjust the volume with VOLUME +/- on the remote commander)

In VPL-EX50:

When INPUT A or INPUT B is selected, the output audio is the signal input to AUDIO (INPUT A/B

AUDIO) that is common to INPUT A and B. When VIDEO or S VIDEO is selected, the output audio is the signal input to AUDIO of VIDEO IN.

In VPL-EW5/EX5/ES5:

When INPUT A is selected, the output audio is the signal input to AUDIO of

INPUT A. When INPUT B (VPL-

EW5 only) is selected, the output audio is the signal input to HDMI connector of INPUT B. When VIDEO or S VIDEO is selected, the output audio is the signal input to AUDIO of

VIDEO IN.

g REMOTE RS-232C connector (D-

sub 9-pin female) (VPL-EX5/

EX50/EW5 only)

Connects to the connector of the computer when you operate the projector from the computer.

h Rear remote control detector

Remote Commander

The keys that have the same names as those on the control panel function identically.

1

2

3

4

5

6

7

APA INPUT

KEY

STONE

RESET

PIC

MUTING

D ZOOM

FREEZE

ENTER

MENU

VOLUME a INPUT key b APA (Auto Pixel Alignment) key

Automatically adjusts a picture to its clearest while a signal is input from a computer.

For details, see “Smart APA” in “The

SET SETTING Menu” on page 35.

c KEYSTONE (Trapezoidal

distortion correction) key

Adjusts the vertical trapezoidal distortion of the image. Pressing this key, the adjustment menu are displayed.

8

9

0 qa qs qd

Location and Function of Controls

15

Use the arrow keys (v/V/b/B) for adjustment.

d RESET key

Resets the value of an item to its factory preset value or returns the enlarged image to its original size. This key functions when the menu or a setting item is displayed on the screen.

e PIC MUTING key

Cuts off the picture. Press again to restore the picture.

f FREEZE key

Freezes the projected picture. To cancel the frozen picture, press the key again.

g D ZOOM (Digital Zoom) +/– key

Enlarges the image at a desired location on the screen.

h Infrared transmitter i ?/1 (On/Standby) key j v

/

V

/

b

/

B

(Arrow) keys

k ENTER key l MENU key m VOLUME +/– keys

Before using the Remote

Commander

Pull out the clear film from the lithium battery holder.

To replace a battery

1

Release the lock of the lithium battery holder by picking it, and pull out the holder from the Remote Commander.

2

Install the lithium battery.

Face the + side up.

3

Put the lithium battery holder back into the Remote Commander.

Notes on the lithium battery

• A button type lithium battery (CR2025) is used in the Remote Commander. Do not use batteries other than CR2025.

• Keep the lithium battery out of the reach of children.

• Should the battery be swallowed, immediately consult a doctor.

Notes on Remote Commander operation

• Make sure that nothing obstructs the infrared beam between the Remote

Commander and the remote control detector on the projector. Direct the

Remote Commander toward the remote control detector.

• The operation range is limited. The shorter the distance between the Remote

Commander and the remote control detector is, the wider the angle within which the commander can control the projector becomes.

16

Location and Function of Controls

B Projecting the Picture

Installing the Projector

The distance between the lens and the screen varies depending on the size of the screen. Use the following table as a guide.

Screen

Distance between the screen and the center of the lens

*

Adjuster not stretched, and the V Keystone function has been done.

VPL-EX50/EX5/ES5

Projected image size (diagonal)

(inches)

Minimum Distance

40 80 100 150 200 250

Unit: m (feet)

300

Maximum

Distance

1.2

(3.9)

1.3

(4.3)

2.4

(7.9)

2.7

(8.9)

3.0

(9.8)

3.4

(11.2)

4.4

(14.4)

5.2

(17.1)

5.9

(19.4)

7.0

(23.0)

7.4

(24.3)

8.7

(28.6)

8.8

(28.9)

10.5

(34.5)

There may be a slight difference between the actual value and the design value shown in the table above.

Installing the Projector

17

VPL-EW5

(When “Aspect” on the Signal menu is set to “Full 2”

Projected image size (diagonal)

(inches)

Minimum Distance

Maximum

Distance

40

1.3

(4.3)

1.4

(4.6)

80

2.5

(8.2)

2.9

(9.5)

100

3.1

(10.2)

3.6

(11.8)

150

4.7

(15.4)

5.5

(18.1)

200

6.2

(20.3)

7.4

(24.3)

250

7.8

9.2

Unit: m (feet)

(25.6)

(30.2)

300

9.3

(30.5)

11.1

(36.4)

There may be a slight difference between the actual value and the design value shown in the table above.

Notes for VPL-EW5 only

• When “Aspect” on the Signal menu is set to other than “Full 2”, black bands may appear at the top and bottom or right and left of the screen.

• When “Aspect” in the Signal menu is set to “4:3”, the projected image size (diagonal) will be approximately 88 % of “Full 2” size.

• When “Aspect” in the Signal menu is set to “16:9”, the projected image size (diagonal) will be approximately 97 % of “Full 2” size.

For details on installation, see “Installation Diagram” on page 54.

18

Installing the Projector

Connecting the

Projector

When you connect the projector, make sure to:

• Turn off all equipment before making any connections.

• Use the proper cables for each connection.

• Insert the cable plugs firmly; loose connections may increase noise and reduce performance of picture signals.

When pulling out a cable, be sure to pull it out by the plug, not the cable itself.

Connecting a Computer

This section describes how to connect the projector to a computer.

For more information, refer to the computer’s instruction manual.

To connect a computer

Rear side

to monitor output

VPL-EX50

Computer to audio output

1

HD D-sub 15-pin cable (supplied)

2

Stereo audio connecting cable (not supplied)

(Use a no-resistance cable.)

Notes

• For stereo audio connection, connect the stereo audio connecting cable to following connectors:

VPL-EX5/ES5: INPUT A/VIDEO IN

AUDIO connector

VPL-EW5: INPUT A AUDIO connector

VPL-EX50: INPUT A/B AUDIO connector

• The projector accepts VGA, SVGA, XGA,

SXGA, SXGA+, WXGA signals. However, we recommend that you set the output mode of your computer to SVGA (VPL-ES5),

XGA (VPL-EX5/EX50) or WXGA (VPL-

EW5) mode for the external monitor.

Connecting the Projector

19

• If you set your computer, such as a notebook computer, to output the signal to both your computer’s display and the external monitor, the picture of the external monitor may not appear properly. Set your computer to output the signal to only the external monitor.

For details, refer to the operating instructions supplied with your computer.

To connect a computer (Digital) or video equipment (Digital) (VPL-EW5 only)

Front (the connector panel on the right of the lens)

VPL-EW5

Note

To connect a Macintosh computer equipped with a video output connector of a type having two rows of pins, use a commercially available plug adaptor.

to DVI-D output connector

Computer to HDMI connector DVD player

1

HDMI-DVI-D cable (not supplied)

2

HDMI cable (not supplied)

Notes

• Be sure to use the HDMI cable with an

HDMI logo.

• The HDMI connector of this projector is not compatible with DSD (Direct Stream

Digital) Signal or CEC (Consumer

Electronics control) Signal.

20

Connecting the Projector

Connecting a VCR

This section describes how to connect the projector to a VCR.

For more information, refer to the instruction manuals of the equipment you are connecting.

To connect to a video or S video output connector

Rear side

VPL-EX50

To connect to a video GBR/

Component output connector

Rear side

VPL-EX50

to audio output

(L) to audio output

(R) to video

GBR/ component output to S video output to audio output (L) to video output to audio output (R)

VCR

1

Stereo audio connecting cable (not supplied)

(Use a no-resistance cable.)

2

Video cable (not supplied) or S-Video cable

(not supplied)

VCR

1

Signal Cable (not supplied)

HD D-sub 15-pin (male)

↔ 3 × phono jack

2

Stereo audio connecting cable (not supplied)

(Use a no-resistance cable.)

Notes

• For stereo audio connection, connect the stereo audio connecting cable to following connectors:

VPL-EX5/ES5: INPUT A/VIDEO IN

AUDIO connector

VPL-EW5: INPUT A AUDIO connector

VPL-EX50: INPUT A/B AUDIO connector

• Set the aspect ratio using “Aspect” on the

INPUT SETTING menu according to the input signal.

• When you connect the projector to a video

GBR output connector, select “Video GBR” or when you connect the projector to a component output connector, select

“Component” with the “Input-A Signal Sel.” setting on the SET SETTING menu.

Connecting the Projector

21

Projecting

1,2

4

Press the INPUT key to select the input source.

Each time you press the key, the input signal switches as follows:

Input-A t Input-B t Video t S-Video

(VPL-EW5/EX50 only)

Rear remote control detector

APA INPUT

KEY

STONE

RESET

PIC

MUTING

D ZOOM

FREEZE

ENTER

MENU

VOLUME

1

Plug the AC power cord into a wall outlet, and connect all equipment, then remove the lens cover.

The ?/1 key lights in red and the projector goes into standby mode.

2

Press the ?/1 key.

The ?/1 key lights after flashing in green. (The projector cannot be used while the ?/1 key is flashing.)

3

Turn on the equipment connected to the projector.

To input from

Computer/Component connected to the INPUT

A connector

Computer connected to the INPUT B connector

(VPL-EX50 only)

Computer/VCR, etc. connected to INPUT B

(Digital) connector

(VPL-EW5 only)

Video equipment connected to the VIDEO input connector

Video equipment connected to the

S VIDEO input connector

Press INPUT to display

Input-A

Input-B

Video

S-Video

Smart APA (Auto Pixel Alignment) adjusts the picture of the connected equipment so that it is projected clearly.

Notes

• If “Auto Input Search” is set to “On,” the projector searches for the signals from the connected equipment and displays the input channel where the input signals are found.

For details, see “Auto Input Search” on page 35.

• The Smart APA feature is effective for the input analog signal from a computer only.

5

Switch the equipment connected to output to the projector.

Depending on the type of your computer, for example a notebook, or an all-in-one LCD type, you may have to switch the computer to output to the projector by pressing certain keys (e.g.,

22

Projecting

LCD

/

VGA

,

/

, etc.), or by changing your computer’s settings.

F7

and

Fn

or

Fx

Note

The key used for switching the computer to output to the projector varies depending on the type of computer.

6

Adjust the upper or lower position of the picture.

Use the adjuster to adjust the picture position.

Using the adjuster

Lift the projector while pressing the adjuster adjustment button, and adjust the tilt of the projector, then release the button to lock the adjuster.

For VPL-EW5/EX50/EX5

• When you adjust the tilt of the projector with the adjuster, the V keystone adjustment is performed at the same time. If you do not want to perform the automatic keystone adjustment, set the

“V Keystone” to “Manual.” (See

page 38.)

• If you set the “V Keystone” to “Auto,” the “V Keystone” correction is automatically adjusted. However, it may not be perfectly adjusted depending on the room temperature or the screen angle. In this case, adjust it manually.

Press the KEYSTONE key to “V

Keystone” displays on the screen, and adjust the value with the v/V/b/B keys.

8

Adjust the size of the picture and the focus.

Adjust the picture size using the Zoom ring and adjust the picture focus using the Focus ring.

Adjuster adjustment button

Notes

• Be careful not to let the projector down on your fingers.

• Do not push hard on the top of the projector or do not drag it hard with the adjuster out. It may be occurred malfunction.

7

Adjust the trapezoidal distortion

( ) of the picture. (VPL-ES5 only)

Press the KEYSTONE key on the

Remote Commander to display the adjustment menu and adjust the tilt using the v/V/b/B keys.

Projecting

23

Turning Off the

Power

1

Press the ?/1 key.

“POWER OFF? Please press ?/1 key again.” appears to confirm that you want to turn off the power.

Note

The message disappears if you press any key other than the ?/1 key, or if you do not press any key for five seconds.

2

Press the ?/1 key again.

The ?/1 key flashes in green and the fan continues to run to reduce the internal heat. Also, the ?/1 key flashes quickly for the first 60 seconds. During this time, you will not be able to light up the ?/1 key again with the ?/1 key.

3

Unplug the AC power cord from the wall outlet after the fan stops running and the

?/1 key

lights in red. (Except when using the Direct Power On/Off function or the Off & Go function.)

24

Turning Off the Power

B Convenient Functions

Selecting the Menu

Language

You can select one of seventeen languages for displaying the menu and other on-screen displays. The factory setting is English.

To change the menu language, proceed as follows:

1,2

The menu currently selected is shown as a yellow button.

4

Press the v or V key to select the

MENU SETTING menu, then press the B or ENTER key.

The selected menu appears.

Rear remote control detector

5

Press the v or V key to select

“Language,” then press the B or

ENTER key.

1

Plug the AC power cord into a wall outlet.

2

Press the ?/1 key to turn on the projector.

3

Press the MENU key.

The menu appears.

6

Press the v, B, b or V key to select a language, then press the ENTER key.

The menu changes to the selected language.

To clear the menu

Press the MENU key.

The menu disappears automatically if a key is not pressed for one minute.

Selecting the Menu Language

25

Security Lock

The projector is equipped with a security lock function. When you turn the power of the projector on, you are required to input the previously set password. If you do not input the correct password, you will not be able to project the picture.

Notes

• You will not be able to use the projector if you forget your password and the password administrator is not available. Be please aware that using the security lock can prevent valid usage in such cases.

• When you set the security lock being active, the password will be necessary only when the power is turned on after plugging the power cord.

To use the security lock

1

Press the MENU key and then, on the

INSTALL SETTING menu, turn on the

“Security Lock”

setting.

2

Enter the password.

Use the MENU, v/V/b/B, and ENTER keys to enter the four-digit password.

(The default initial password setting is

“ENTER, ENTER, ENTER, ENTER.”

After this is entered you can put in your own password. Therefore, when you use this function for the first time, please input “ENTER” four times.)

Enter the password on this screen.

Enter new password key.

Power-on cannot be performed without the password.

Use: Cancel: Other key

3

Enter the password again to confirm.

Re-enter new password key.

Be sure to remember this password.

Use: Cancel: Other key

When the following message is displayed, the setting for security lock is completed.

If “Invalid Password!” is displayed on the screen, perform this procedure again from step 1.

Enter password key.

Password required for power-on.

Use: Cancel: Other key

Next, the screen for entering the new password is displayed. (Enter the password on this screen even if you want to keep the current password.)

4

Turn the main power off and disconnect the AC power cord.

The security lock is set to on, then it becomes effective. The screen used for entering the password is displayed when the power is turned on the next time.

Security certification

When the password screen is displayed, enter the password that was set. If you fail to enter the correct password after three tries, the projector cannot be used. In this case, press the ?/1 key to turn off the power.

To cancel the security lock

1

Press the MENU key, then turn off the

“ Security Lock ” setting on the

INSTALL SETTING menu.

26

Security Lock

2

Enter the password.

Enter the password that was set.

Note

If you call the customer service center because you have forgotten the password, you will need to be able to verify the projector’s serial number and your identity. (This process may differ in other countries/regions.) Once your identity has been confirmed, we will provide you with the password.

Other Functions

Direct Power On/Off Function

If you will be using a circuit breaker to turn the power for the entire system on and off, set the direct power on function to “On.” You can turn the power on/off without pressing the power key on the projector.

Off & Go Function

If you are leaving the conference room immediately, turn the projector off, and then, you can unplug the AC power cord.

Effective Tools for Your

Presentation

To enlarge the image (Digital Zoom function)

You can select a section of the image to enlarge. This function works when a signal from a computer is input.

This function does not work when a video signal is input.

1

Project a normal image, and press the

D ZOOM + key on the Remote

Commander.

The digital zoom icon appears in the center of the image.

Digital zoom icon

2

Move the icon to the point on the image you want to enlarge. Use the arrow key (v/V/b/B) to move the icon.

3

Press the D ZOOM + key again.

The portion of the image where the icon is located is enlarged. The enlargement

Other Functions

27

ratio is displayed on the screen for a few seconds.

By pressing the + key repeatedly, the image size (ratio of enlargement: max. 4 times) increases.

Use the arrow key ( v/V/b/B

) to scroll the enlarged image.

To return the image to its original size

Press the D ZOOM – key.

Just pressing the RESET key returns the image back to its original size immediately.

To freeze the image projected

(Freeze function)

Press the FREEZE key. “Freeze” appears when the key is pressed. This function works when a signal from a computer is input.

To restore the original screen, press the

FREEZE key again.

28

Other Functions

B Adjustments and Settings Using a Menu

Using a MENU

2

Use the v or V key to select a menu, then press the B or ENTER key.

The selected menu appears.

The projector is equipped with an on-screen menu for making various adjustments and settings.

Display items

3

Select an item.

Use the v or V key to select the item, then press the B or ENTER key.

The setting items are displayed in a popup menu or in a sub menu.

Input signal indicator

Pop-up menu

Menu

Setting items

Selected input signal

Input signal setting indicator

Picture adjustment menu

MENU SETTING

S t a t u s :

L a n g u a g e :

M e n u Po s i t i o n :

S t a r t U p I m a g e

O n

E n g l i s h

To p l e f t

B o t t o m L e f t

C e n t e r

To p R i g h t

B o t t o m R i g h t

Input A

A

Input signal indicator

Shows the selected input channel. x is displayed when no signal is input. You can hide this indicator using “Status” on the

MENU SETTING menu.

Input signal setting indicator

For Input-A: Shows “Auto” or “Input-A

Signal Sel.” setting on the SET

SETTING menu.

For Video/S-Video input: Shows “Auto” or the “Color System” setting on the SET

SETTING menu.

1

Press the MENU key.

The menu appears.

The menu presently selected is shown as a yellow button in the column on the left.

SET SETTING

S m a r t A PA : O n

Au t o I n p u t S e a rch : O f f

Input-A Signal Sel.: C o m p o n e n t

C o l o r S y s t e m :

Pow e r S av i n g :

I R R e c e i v e r : F ro n t & R e a r

Pa n e l Key L o ck : O f f

L a m p T i m e r R e s e t

Au t o

O f f

Input-A

Sub menu

Menu Setting items

PICTURE SETTING Input A

A D J U S T P I C T U R E S t a n d a rd

C o n t r a s t : 8 0

B r i g h t n e s s : 5 0

G a m m a M o d e :

C o l o r Te m p . :

G r a p h i c s

H i g h

4

Make the setting or adjustment of an item.

• When changing the adjustment level:

To increase the number, press the v or

B key.

To decrease the number, press the V or b key.

Press the ENTER key to restore the previous screen.

• When changing the setting:

Press the v or V key to change the setting.

Press the ENTER or b key to restore the previous screen.

Using a MENU

29

To clear the menu

Press the MENU key.

The menu disappears automatically if a key is not pressed for one minute.

To reset items that have been adjusted

Select the item that you want to reset, and then press the RESET key on the Remote

Commander.

“Complete!” appears on the screen and the

setting of the item that you have selected is reset to its factory preset value.

Items that can be reset are:

• “Contrast,” “Brightness,” “Color,” “Hue” and “Sharpness” on the “Adjust Picture...” menu of the PICTURE SETTING menu

• “Dot Phase,” “H Size,” and “Shift” on the

“Adjust Signal...” menu of the INPUT

SETTING menu

Storage of the settings

The settings are automatically stored in the projector memory when the ENTER key is pressed.

If no signal is input

If there is no input signal, “Cannot adjust this item.” appears on the screen.

Unadjustable items

Items that cannot be adjusted, depending on the input signal, are not displayed on the menu.

For details, see page 41.

30

Using a MENU

The PICTURE SETTING Menu

The PICTURE SETTING menu is used for adjusting the picture or volume.

Items that can be adjusted or set depend on the kind of input signals.

For details, see “Input signals and adjustable/setting items” on page 41.

PICTURE SETTING

P i c t u r e M o d e

A d j u s t P i c t u r e . . .

S t a n d a rd

Vo l u m e : 3 0

Input A

PICTURE SETTING

Input-A

A D J U S T P I C T U R E S t a n d a rd

C o n t r a s t : 8 0

B r i g h t n e s s : 5 0

G a m m a M o d e : G r a p h i c s

C o l o r Te m p . : H i g h

Setting items

Picture Mode

Adjust Picture...

Contrast

Brightness

Color

Hue

Sharpness

Functions

Selects the picture mode.

• Dynamic: Emphasizes the contrast to produce a

“dynamic” picture.

• Standard: Selects for the standard picture.

• Game: Select for viewing game picture.

• Living: Select for viewing sports, music, digital video camera picture.

• Cinema: Select for viewing film-like picture.

• Presentation: Makes the picture suitably bright for a presentation when the signal is input from a computer.

Initial setting

Set according to the input signal

The unit can store the setting values of the following sub menu items for each picture mode separately.

Adjusts the picture contrast.

80

Adjusts the picture brightness.

Adjusts color intensity.

Adjusts color tones. The higher the setting, the more greenish the picture becomes. The lower the setting, the more purplish.

Adjusts the picture sharpness. The higher the setting, the sharper the picture becomes. The lower the setting, the softer the picture becomes.

50

50

50

30

Gamma Mode Selects a gamma correction curve.

• Graphics: Improves the reproduction of halftones.

Photos can be reproduced in natural tones.

• Text: Contrasts black and white. Suitable for images that contain lots of text.

Color Temp.

Adjusts the color temperature.

• High: Makes white colors bluish.

• Middle: Makes white part of the picture natural white.

• Low: Makes white colors reddish.

Graphics

Set according to the input signal

The PICTURE SETTING Menu

31

Setting items

DDE (Dynamic

Detail

Enhancer)

Volume

Functions

Selects the mode to play the input video signal according to the material.

• Off: Plays back the interlace format without conversion.

• Progressive: Plays back the video picture of the interlace format converting to progressive.

• Film: Plays back a smooth picture in a softwear of 2-

2, 2-3 pull-down type like a movie. When other than the softwear of 2-2, 2-3 pull-down type is played back, it is automatically switched to "Progressive".

Adjusts the volume.

Initial setting

Film

30

Note

When the Picture Mode is set to “Presentation”, the items of “Color Temp.” are not displayed.

32

The PICTURE SETTING Menu

The INPUT SETTING Menu

The INPUT SETTING menu is used to adjust the input signal.

When the signal is input from a computer

Setting items

Adjust Signal...

Dot Phase

Functions Initial setting

H Size

Shift

Aspect (When the video signal is input)

Adjusts the dot phase of the LCD panel and the signal output from a computer.

Adjust the picture further for finer picture after the picture is adjusted by pressing the APA key.

Adjusts the horizontal size of a picture output from a computer. Adjust the setting according to the dots of the input signal.

For details, see page 52.

Adjusts the position of the picture. H adjusts the horizontal position of the picture.V adjusts the vertical position of the picture. As the setting for H increases, the picture moves to the right, and as the setting decreases, the picture moves to the left.

As the setting for V increases, the picture moves up, and as the setting decreases, the picture moves down.

Use the b or the

B

key to adjust the horizontal position and the v

and

V

key for the vertical position.

You can set the aspect ratio of the picture to be displayed for the current input signal. This item is enabled only when an video signal (preset memory numbers 1 to 11) is input.

• Normal*

1

: Select to view a picture with normal 4:3 aspect ratio.

• 4:3: Makes the aspect ratio 4:3.

• 16:9*

2

: Select to view a picture squeezed.

• Full*

1

: The original image is projected fully in the window.

• Zoom: Select to enlarge the original picture without distorting the aspect ratio.

• Wide Zoom: Select to enlarge to full screen with minimum distortion.

Set according to the input signal

Set according to the input signal

Set according to the input signal

Set according to the input signal

The INPUT SETTING Menu

33

Setting items Functions

Aspect (When the

PC signal is input)

You can set the aspect ratio of the picture to be displayed for the current input signal. This item is enabled only when an PC signal (preset memory numbers 21 to 63) is input.

• Full 1: Displays a picture vertically or horizontally to fill the screen without changing the aspect ratio of the original picture.

• Full 2:The original image is projected fully in the window.

• Normal: Displays the picture while matching one pixel of input picture element to that of the LCD. The picture will be clear but the picture size will be smaller.

• Zoom: Select to enlarge the original picture without distorting the aspect ratio.

*

*

1

2

: VPL-EW5 only

: VPL-EX5/EX50/EW5 only

Initial setting

Set according to the input signal

Note

Note that if the projector is used for profit or for public viewing, modifying the original picture by switching to the wide mode may constitute an infringement of the rights of authors or producers, which are legally protected.

About the Preset Memory No.

This projector has 45 types of preset data for input signals (the preset memory). When a preset signal is input, the projector automatically detects the signal type and recalls the data for the signal from the preset memory to adjust it to an optimum picture.

The memory number and signal type of that signal are displayed on the INFORMATION

menu (See page 40). You can also adjust the

preset data through the INPUT SETTING menu.

See the chart on page 52 to find if the signal

is registered in the preset memory.

Note

When the aspect ratio of input signal is other than “Full 2”, a part of the screen may be displayed in black.

34

The INPUT SETTING Menu

The SET SETTING Menu

The SET SETTING menu is used for changing the settings of the projector.

SET SETTING

S m a r t A PA : O n

Au t o I n p u t S e a rch : O f f

I n p u t - A S i g n a l S e l . : Au t o

C o l o r S y s t e m : Au t o

Pow e r S av i n g :

I R R e c e i v e r :

O f f

F ro n t & R e a r

Pa n e l Key L o ck : O f f

L a m p T i m e r R e s e t

Input-A

Setting items

Smart APA

Functions

The APA (Auto Pixel Alignment) automatically adjusts “Dot Phase,” “H Size” and “Shift” on the

INPUT SETTING menu for the input signal from a computer.

• On: When a signal is input from a computer, the

APA functions automatically so that the picture can be seen clearly. Once the specified input signal has been adjusted by the “Smart APA,” it will not be readjusted even when the cable is disconnected and connected again or the input channel is changed. You can adjust the picture by pressing the APA key on the

Remote Commander even if “Smart APA” set to

“On.”

• Off: The APA functions when you press the APA key on the Remote Commander.

Auto Input Search When set to “On,” the projector detects input signals in the following order: Input-A/Input-B (VPL-EW5/

EX50 only)/Video/S-Video. It indicates the input channel when the power is turned on or the INPUT key is pressed.

Input-A Signal Sel.

Selects the type of signal input from the equipment connected to the INPUT A connector.

Selects the type of signal input from the equipment by selecting “Input-A” with the INPUT key.

• Auto: Selects the input signal type automatically.

• Computer: Inputs the signal from a computer.

• Component: Inputs the component signal from a

DVD player/recorder, Blu-ray Disc player, digital tuner, etc.

• Video GBR: Inputs the signal from a TV game or

HDTV broadcast.

Color System Selects the color system of the input signal.

If you select “Auto,” the projector detects the color system of the input signal automatically. If the picture is distorted or colorless, select the color system according to the input signal.

Initial setting

On

Off

Auto

Auto

The SET SETTING Menu

35

Setting items Functions

Power Saving

IR Receiver

Selects the Power Saving mode.

• Lamp off: The lamp goes off if no signal is input for

10 minutes. The lamp lights again when a signal is input or any key is pressed.

• Standby: The projector goes into Standby mode if no signal is input for 10 minutes. To use it, turn on the power again.

• Off: The projector does not go into Power Saving mode.

Selects the remote control detectors (IR Receiver) on the front and rear of the projector.

• Front & Rear: Activates both the front and rear detectors.

• Front: Activates the front detector only.

• Rear: Activates the rear detector only.

Panel Key Lock Locks all the control panel keys on the top panel of the projector so that the projector can be operated only with the Remote Commander.

To lock the control panel keys, set to “On.”

When it is set to “On,” keeping the ?/1 key on the control panel pressed for 10 seconds turns the projector on when it is in standby mode, and turns the projector to standby mode when the power is on. If you press and hold the MENU key for about 10 seconds when the power is on, the lock will be released and “Panel

Key Lock” is automatically set to “Off.”

Lamp Timer Reset When replacing the lamps, reset the lamp timer.

Initial setting

Off

Front & Rear

Off

–

Notes

• Press the APA key when the full image is displayed on the screen. If the projected image includes a black portion around it, the APA function will not work properly and some parts of the image may not be displayed on the screen.

- You can cancel the adjustment by pressing the APA key again while “Adjusting” appears on the screen.

- The picture may not be adjusted properly depending on the type of input signal.

- Adjust the “Dot Phase,” “H Size,” and “Shift” items on the INPUT SETTING menu when you adjust the picture manually.

• If the input signal is not displayed correctly when the input A signal classifying is set to "Auto", set it to conform the input signal.

36

The SET SETTING Menu

The MENU SETTING Menu

The MENU SETTING menu is used for changing the menu displays.

Setting items

Status (on-screen display)

Language

Menu Position

Start Up Image

Functions Initial setting

Sets up the on-screen display.

When set to “Off,” turns off the on-screen displays except for the menus, a message when the power is turned off, and warning messages.

On

Selects the language used in the menu and on-screen displays. The languages available are: English,

Nederlands, Français, Italiano, Deutsch, Español,

English

Português, , , and .

Selects the display position of the menu from “Top

Left,” “Bottom Left,” “Center,” “Top Right,” and

“Bottom Right.”

• On: Displays the Start Up Image in the window after turning on the power.

• Off: Does not displays the Start Up Image in the window after turning on the power.

Center

On

The MENU SETTING Menu

37

The INSTALL SETTING Menu

The INSTALL SETTING menu is used for changing the settings of the projector.

INSTALL SETTING

V Key s t o n e : Au t o

I m a g e F l i p : O f f

B a ck g ro u n d : B l u e

L a m p M o d e : S t a n d a rd

H i g h A l t i t u d e M o d e : O f f

S e c u r i t y L o ck : O f f

D i r e c t Pow e r O n : O f f

Input-A

Setting items

V Keystone

(VPL-EX50/

EX5/EW5 only)

V Keystone

(VPL-ES5 only)

Image Flip

Background

Lamp Mode

(VPL-EW5/

EX50 only)

High Altitude

Mode

Security Lock

Functions

Corrects the trapezoidal distortion caused by the projection angle. Select “Auto” for automatic correction, or “Manual” for manual correction using the v/V/b/B keys.

When the bottom of the trapezoid is longer than the top

: Sets a lower value.

When the top of the trapezoid is longer than the bottom

: Sets a higher value.

Initial setting

Auto

Corrects the trapezoidal distortion caused by the projection angle using the v/V/b/B keys on the Remote Commander.

When the bottom of the trapezoid is longer than the top

: Sets a lower value.

When the top of the trapezoid is longer than the bottom

: Sets a higher value.

0

Off Flips the image on the screen horizontally and/or vertically.

• HV: Flips the image horizontally and vertically.

• H: Flips the image horizontally.

• V: Flips the image vertically.

• Off: The image does not flip.

Selects the background color of the screen when no signal is input to the projector. Select “Black” or “Blue.”

Normally, set to “Blue.”

Sets the lamp brightness used during the projection.

• High: Illuminates the projected image brightly.

• Standard: Reduces fan noise and power consumption.

The brightness of the projected image will be lower compared with the “High” setting.

Blue

Standard

Set to “On” when the projector is used at an altitude of

1,500 m or higher.

Turns on the projector’s security lock function.

When set to “On,” turns on the security lock function, which locks the projector once a password has been set.

For details, see “Security Lock” on page 26.

Off

Off

Direct Power On Set to “On” if you are using a circuit breaker to turn the power on/off the entire system. You can turn the power on/ off without pressing the power key on the projector.

Off

38

The INSTALL SETTING Menu

Note

If you set “High Altitude Mode” to “On” at an altitude of under 1,500 m, the reliability of the lamp may be reduced.

Notes on VPL-EX50/EX5/EW5

• The auto V Keystone adjustment may not correct the trapezoidal distortion perfectly, depending on the room temperature or the screen angle.

• If you need fine adjustment when V Keystone is set to “Auto”, press the KEYSTONE key on the control panel or the remote commander, and change the value. The setting mode will be temporarily changed to “Manual” from “Auto”.

If you want restore the “Auto” setting, first switch the V Keystone setting to “Manual”, then return it to “Auto”.

• When you want to apply the fine adjustment value the next time, change the V Keystone setting to

“Manual” from “Auto”.

The INSTALL SETTING Menu

39

The INFORMATION Menu

The INFORMATION menu displays the model name, serial number, the horizontal and vertical frequencies of the input signal and the cumulated hours of usage of the lamp.

INFORMATION

V P L - E X 5 0 Serial No. 3 3 3 3 3 3 3 f H : 4 8 , 4 7 k H z f V: 6 0 , 0 0 H z

N o . 2 3

1 0 2 4 x 7 6 8

L a m p T i m e r : 2 H

I n p u t A

Model name

Serial number

Memory number of an input signal

Signal type

Setting items

fH fV

Lamp Timer

Functions

Displays the horizontal frequency of the input signal.

The displayed value is approximate.

Displays the vertical frequency of the input signal.

The displayed value is approximate.

Indicates how long the lamp has been turned on.

Note

These are only displayed on the screen. You cannot alter the display, and these is no setting to be altered.

40

The INFORMATION Menu

Input signals and adjustable/setting items

Some of the items in the menus cannot be adjusted depending on the input signal as indicated in the following tables. The items that cannot be adjusted are not displayed in the menu.

Adjust Picture... menu

Item

Picture Mode

Adjust Picture...

Contrast

Brightness

Color

Hue

Video or S-Video

(Y/C)

z z z z

Component

z z z z

Sharpness

Gamma Mode

Color Temp.

DDE z

(NTSC 3.58/4.43 only) z

– z z

Volume z z : Adjustable/can be set

– : Not adjustable/cannot be set

*1

*2

: Except for preset memory No. 7, 8

: Cannot be set in the Presentation mode z z

– z z

(Interlace format only)

*1 z

Input signal

Video GBR

z z z z z z

– z z

(Interlace format only)

*1 z

Computer

z z z

–

–

– z z

– z

*2

INPUT SETTING menu

Item

Video/S-Video (Y/C) Component

Input signal

Video GBR

z z z

Aspect

Adjust Signal

Dot Phase

H size

Shift

–

–

– z : Adjustable/can be set

– : Not adjustable/cannot be set

*3

: Can be set except preset memory number 49.

–

– z

–

– z z z z

B&W

Computer

z

*3 z z z

– z z z z

–

–

The INFORMATION Menu

41

B Maintenance

Replacing the Lamp

The lamp used as a light source is consumable product. Thus replace the lamp with a new one in the following cases.

• When the lamp has burnt out or dims

• “Please replace the Lamp.” appears on the screen

• The LAMP/COVER indicator lights up

(repeats flashing three times)

The lamp life varies depending on conditions of use.

Use an LMP-E190 Projector Lamp as the replacement lamp.

Use of any other lamps than the LMP-E190 may cause damage to the projector.

Notes

• If the lamp breaks, ask qualified Sony personnel to replace the lamp and to check inside.

• Pull out the lamp by holding the handle.

• When removing the lamp, make sure it remains horizontal, then pull straight up. Do not tilt the lamp. If you pull out the lamp while it is tilted and if the lamp breaks.

1

Turn off the projector, and disconnect the AC power cord from the AC outlet.

Note

When replacing the lamp after using the projector, wait for at least an hour for the lamp to cool.

2

Place a protective sheet (cloth) beneath the projector. Turn the projector over so you can see its underside.

Note

Be sure that the projector is stable after turning it over.

3

Open the lamp cover by loosening the screw with a Phillips screwdriver.

Note

For safety reasons, do not loosen any other screws.

4

Loosen the two screws on the lamp unit with the Phillips screwdriver (a).

Fold out the handle (b), then pull out the lamp unit by the handle (c).

Handle

42

Replacing the Lamp

5

Insert the new lamp all the way in until it is securely in place (a). Tighten the two screws (b). Fold down the handle to replace it (c).

11

Select “Lamp Timer Reset”, and then press the ENTER key.

SET SETTING

S m a r t A PA : O n

Au t o I n p u t S e a rch : O f f

I n p u t - A S i g n a l S e l . : Au t o

C o l o r S y s t e m : Au t o

Pow e r S av i n g : O f f

I R R e c e i v e r : F ro n t & R e a r

Pa n e l Key L o ck : O f f

L a m p T i m e r R e s e t

Input-A

Notes

• Be careful not to touch the glass surface of the lamp.

• The power will not turn on if the lamp is not secured properly.

• Do not allow any liquid or other objects into the slot to avoid electrical shock or

fire.

6

Close the lamp cover and tighten the screw.

Note

Be sure to attach the lamp cover securely as it was. If not, the projector cannot be turned on.

7

Turn the projector back over.

8

Connect the power cord.

The ?/1 key lights in red.

9

Press the ?/1 key to turn the projector on.

10

Press the MENU key, and then select the Setup menu.

12

Select “Execute” with the V key, and then press the ENTER key.

The Lamp Timer is initialized to 0, and

“Change the Lamp and clean the Filter?” is displayed in the menu screen.

Change the Lamp and clean the Filter?

Yes: No:

Refer to page 44 for “Cleaning the Air

Filter”.

13

Select “Yes” with the v key.

“Lamp Timer Reset Complete!” is displayed in the menu screen.

Disposal of the used lamp

For the customers in the USA

Lamp in this product contains mercury.

Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the

Electronic Industries Alliance

(www.eiae.org).

Replacing the Lamp

43

Cleaning the Air

Filter

The air filter should be cleaned whenever you replace the lamp.

Remove the air filter, and then remove the dust with a vacuum cleaner.

The time needed to clean the air filter will vary depending on the environment or how the projector is used.

When it becomes difficult to remove the dust from the filter with a vacuum cleaner, remove the air filter and wash it.

1

Turn the power off and unplug the power cord.

2

Draw out the air filter cover and remove it.

Air filter

5

Attach the air filter so that it fits into the each claws on the air filter cover and replace the cover.

Notes

• If you neglect to clean the air filter, dust may accumulate, clogging it. As a result, the temperature may rise inside the unit, leading to a possible malfunction or fire.

• Be sure to attach the air filter cover firmly; the power can not be turned on if it is not closed securely.

• The air filter has a face and a reverse side.

Place the air filter so that it fits in a notch on the air filter cover.

3

Remove the air filter.

Claws

4

Wash the air filter with a mild detergent solution and dry it in a shaded place.

44

Cleaning the Air Filter

B Others

Troubleshooting

If the projector appears to be operating erratically, try to diagnose and correct the problem using the following instructions. If the problem persists, consult with qualified Sony personnel.

Power

Symptom Cause and Remedy

The power is not turned on. • The power has been turned off and on with the ?/1 key at a short interval.

c Wait for about 90 seconds before turning on the power

(see page 24).

• The lamp cover is not secured.

c Close the lamp cover securely (see page 43).

• The air filter cover is detached.

c Attach the air filter cover securely (see page 44).

Picture

Symptom

No picture.

The picture is noisy.

The picture from the

INPUT A connector is colored strangely.

Cause and Remedy

• A cable is disconnected or the connections are wrong.

c Check that the proper connections have been made (see

page 19).

• The connections are wrong.

c This projector is compatible with DDC2B (Digital Data

Channel 2B). If your computer is compatible with DDC, turn the projector on according to the following procedures.

1 Connect the projector to the computer.

2 Turn the projector on.

3 Start the computer.

• Input selection is incorrect.

c Select the input source correctly (see page 22).

• The picture is muted.

c Press the PIC MUTING key to release the picture muting (see

page 16).

• The computer signal is not set to output to an external monitor or set to output both to an external monitor and a LCD monitor of a computer.

c Set the computer signal to output only to an external monitor

(see page 19).

Noise may appear on the background depending on the combination of the number of dots input from the computer and the numbers of pixels on the LCD panel.

c Change the desktop pattern on the connected computer.

The input signal cannot be received at “Auto” of “Input-A Signal

Sel” on the SET SETTING menu, or the setting of “Input-A Signal

Sel” is incorrect.

c Selects “Computer”, “Video GBR” or “Component” correctly

according to the input signal (see page 35).

Troubleshooting

45

Symptom Cause and Remedy

On-screen display does not appear.

Color balance is incorrect.

• The picture has not been adjusted properly.

c Adjust the picture (see page 31).

• The projector is set to the wrong color system.

c Set “Color System” on the SET SETTING menu to match the

color system being input (see page 35).

The picture is too dark.

“Status” on the MENU SETTING menu has been set to “Off.” c Set “Status” on the MENU SETTING menu to “On” (see

page 37).

The picture is not clear.

The image extends beyond the screen.

• Contrast or brightness has not been adjusted properly.

c Adjust the contrast or brightness on the “Adjust Picture...” menu

properly (see page 31).

• The lamp has burnt out or is dim.

c Replace the lamp with a new one (see page 42).

• The picture is out of focus.

c Adjust the focus (see page 23).

• Condensation has accumulated on the lens.

c Leave the projector for about two hours with the power on.

• The APA key has been pressed even though there are black edges around the image.

c Display the full image on the screen and press the APA key.

c Adjust “Shift” on the INPUT SETTING menu properly (see

page 33).

• This input signal cannot be projected as the frequency is out of the acceptable range of the projector.

c Input a signal that is within the range of the frequency.

• The resolution setting of the output signal of the computer is too high.

c Set the output setting to SVGA (VPL-ES5), XGA (VPL-EX50/

EX5) or WXGA (VPL-EW5) (see page 19).

The picture flickers.

“Dot Phase” on the INPUT SETTING menu has not been adjusted properly.

c Adjust “Dot Phase” on the INPUT SETTING menu properly (see

page 33).

Sound

Symptom

No sound.

Cause and Remedy

• A cable is disconnected or the connections are wrong.

c Check that the proper connections have been made (see

page 19).

• The audio connecting cable used is incorrect.

c Use a no-resistance stereo audio cable (see page 19).

• The sound is not adjusted properly.

c Adjust the sound with the VOLUME +/– key on the Remote

Commander or adjust “Volume” on the PICTURE SETTING

menu (see page 32).

46

Troubleshooting

Remote Commander

Symptom

The Remote Commander does not work.

Cause and Remedy

The Remote Commander battery are dead.

c Replace them with new battery (see page 16).

Others

Symptom

The control panel keys do not function.

Cause and Remedy

The control panel keys are locked.

c Unlock the control panel keys (see page 36).

Indicators

Symptom

The LAMP/COVER indicator flashes in orange.

(Repetition rate of 2 flashes)

Cause and Remedy

• The lamp cover or the air filter cover is detached.

c Attach the cover securely (see pages 43 and 44).

The LAMP/COVER indicator flashes in orange.

(Repetition rate of 3 flashes)

• The lamp has reached the end of its life.

c Replace the lamp (see page 42).

• The lamp has reached a high temperature.

c Wait for 60 seconds to cool the lamp and then turn on the power again.

: / 1 key flashes in red.

(Repetition rate of 2 flashes)

• The internal temperature is unusually high.

c Check to see that nothing is blocking the ventilation holes.

• The projector is being used at a high altitude.

c Ensure that “High Altitude Mode” in the Setup menu is set to

“On.”

:

/

1 key flashes in red.

(Repetition rate of 4 flashes)

: / 1 key flashes in red.

(Repetition rate of 6 flashes)

The fan is broken.

c Consult with qualified Sony personnel.

Unplug the AC power cord from the wall outlet after the :/1 key stops flashing, plug the power cord to the wall outlet, and then turn the projector on again. If the ON/STANDBY flashes in red and the problem persists, the electrical system has failed.

c Consult with qualified Sony personnel.

Messages List

Warning Messages

Use the list below to check the meaning of the messages displayed on the screen.

Message

Please replace the Lamp and clean the Filter.

Meaning and Remedy

• It is time to replace the lamp and clean the air filter.

c Replace the lamp (see page 42) and clean the filter (see

page 44).

• When this message appears even after replacing the lamp, the task has not been completed.

c Perform the operation of steps 10 to 13 on page 43

Troubleshooting

47

Caution Messages

Use the list below to check the meaning of the messages displayed on the screen.

Message Meaning and Remedy

Not applicable!

You have pressed the wrong key.

c Press the appropriate key.

The panel keys are locked!

“Panel Key Lock” on the SET SETTING menu is set to “On.” c All the keys on the control panel of the projector are locked.

Operate the projector with the keys on the Remote Commander

(see page 36).

48

Troubleshooting

Specifications

Optical characteristics

Projection system

3 LCD panels, 1 lens, projection system

LCD panel VPL-ES5: 0.63-inch SVGA panel, about 1,440,000 pixels (800 ×

600 × 3)

VPL-EX50/EX5: 0.63-inch XGA panel, about 2,360,000 pixels

(1024 × 768 × 3)

VPL-EW5: 0.59-inchvWXGA panel, about 3,070,000 pixels

(1280 × 800 × 3)

Lens 1.2 times zoom lens f 18.53 to 22.18 mm/F1.65 to 1.93

Lamp 190 W Ultra high pressure lamp

Projected picture size

40 to 300 inches (measured diagonally)

Light output VPL-EX50

1)

: 2500 lm

VPL-EW5

1)

/EX5/ES5: 2000 lm

1)

When the Lamp Mode is set to “High.”

Throwing distance (When placed on the floor./

Adjuster not stretched, and the V Keystone function has been done. )

VPL-EX50/EX5/ES5:

40-inch: 1.2 to 1.3 m

(3.9 to 4.3 feet)

80-inch: 2.4 to 2.7 m

(7.9 to 8.9 feet)

100-inch: 3.0 to 3.4 m

(9.8 to 11.2 feet)

150-inch: 4.4 to 5.2 m

(14.4 to 17.1 feet)

200-inch: 5.9 to 7.0 m

(19.4 to 23.0 feet)

250-inch: 7.4 to 8.7 m

(24.3 to 28.6 feet)

300-inch: 8.8 to 10.5 m

(28.9 to 34.5 feet)

VPL-EW5:

(When “Aspect” on the Signal menu is set to “Full 2”)

40-inch: 1.3 to 1.4 m

(4.3 to 4.6 feet)

80-inch: 2.5 to 2.9 m

(8.2 to 9.5 feet)

100-inch: 3.1 to 3.6 m

(10.2 to 11.8 feet)

150-inch: 4.7 to 5.5 m

(15.4 to 18.1 feet)

200-inch: 6.2 to 7.4 m

(20.3 to 24.3 feet)

250-inch: 7.8 to 9.2 m

(25.6 to 30.2 feet)

300-inch: 9.3 to 11.1 m

(30.5 to 36.4 feet)

There may be a slight difference between the actual value and the design value shown above.

Electrical characteristics

Color system NTSC

3.58

/PAL/SECAM/

NTSC

4.43

/PAL-M/PAL-N/

PAL60 system, switched automatically/manually

(NTSC

4.43

is the color system used when playing back a video recorded in NTSC on a

NTSC

4.43

system VCR.)

Resolution VPL-ES5: 500 horizontal TV lines

(Video input)

800 × 600 dots (RGB input)

VPL-EX5/EX50: 750 horizontal

TV lines (Video input)

1024

× 768 dots (RGB input)

VPL-EW5: 750 horizontal TV lines (video input)

1280 × 800 dots (RGB input)

Acceptable computer signals

2) fH: 19 to 92 kHz

2) fV: 48 to 92 Hz

(Maximum input signal resolution:

SXGA+ 1400

× 1050 fV: 60 Hz)

Set the resolution and the frequency of the signal of the connected computer within the range of acceptable preset signals of the projector.

Applicable video signals

15 k RGB 50/60 Hz, Progressive component 50/60 Hz, DTV

(480/60i, 575/50i, 480/60p,

575/50p, 720/60p, 720/50p,

1080/60i, 1080/50i), Composite

Speaker

Speaker output video, Y/C video

Monaural speaker system, 40

×

28.5 mm (1

5

/

8

× 1

1

/

8

inches)

1 W (max.)

Input/Output

VIDEO IN VIDEO: phono type

Composite video: 1 Vp-p ±2 dB sync negative (75 ohms terminated)

S VIDEO: Y/C mini DIN 4pintype

Specifications

49

INPUT A

INPUT B

Y (luminance): 1 Vp-p ±2 dB sync negative (75 ohms terminated)

C (chrominance): burst 0.286

Vp-p ±2 dB (NTSC) (75 ohms terminated), burst 0.3 Vp-p ±2 dB (PAL) (75 ohms terminated)

AUDIO (VPL-EW5/EX50 only):

Stereo minijack, 500 mVrms, input impedance 47 Kilohms or more

RGB: HD D-sub15-pin (female)

Analog RGB/component:

R/R-Y: 0.7 Vp-p ±2 dB (75 ohms terminated)

G: 0.7 Vp-p ±2 dB (75 ohms terminated)

G with sync/Y: 1 Vp-p ±2 dB sync negative (75 ohms terminated)

B/B-Y: 0.7 Vp-p ±2 dB (75 ohms terminated)

HD: Horizontal sync input: TTL level, positive/negative

VD: Vertical sync input: TTL level, positive/negative

AUDIO (VPL-EW5/EX50 only):

Stereo minijack, 500 mVrms, input impedance 47 Kilohms or more

HDMI (VPL-EW5 only): Digital

RGB/Y C

B

(P

B

) C

R

(P

R

): HDMI

RGB (VPL-EX50 only): HD Dsub15-pin (female) Analog

RGB/component:

R: 0.7 Vp-p ±2 dB (75 ohms terminated)

G: 0.7 Vp-p ±2 dB (75 ohms terminated)

B: 0.7 Vp-p ±2 dB (75 ohms terminated)

HD: Horizontal sync input: TTL level, Positive/negative

VD: Vertical sync input: TTL level, positive/negative

AUDIO INPUT A/VIDEO IN (VPL-EX5/ES5 only)/AUDIO INPUT A/B

(VPL-EX50 only)

OUTPUT

AUDIO: Stereo minijack, 500 mVrms, input impedance 47

Kilohms or more

MONITOR OUT: HD D-sub15pin (female)

R, G, B: Gain Unity: 75 ohms

HD, VD: 4 Vp-p (open), 1 Vp-p

(75 ohms)

AUDIO OUT (variable out):

Stereo minijack

1 Vrms (When the volume is maximum and an input signal is

500 mVrms), output impedance

5 kilohms or less

REMOTE (VPL-EW5/EX50/EX5 only)

RS-232C: D-sub 9 pin

General

Dimensions 314

× 109 × 269 mm (12 3

/

8

×

4

3

/

8

× 10

5

/

8

inches) (w/h/d)

Mass

(without projecting parts)

Approx. 2.9 kg (6 lb 6 oz)

Power requirements

VPL-EX50/EW5: AC 100 to 240

V, 2.6 to 1.1 A, 50/60 Hz

VPL-EX5/ES5: AC 100 to 240 V.

2.2 to 1.0 A, 50/60 Hz

Power consumption

VPL-EX50/EW5: Max.260 W (in standby: 5 W)

VPL-EX5/ES5: Max.220 W (in standby: 5 W)

Heat dissipation

884 BTU (VPL-EX50/EW5)

748 BTU (VPL-EX5/ES5)

Operating temperature

0°C to 35°C (32°F to 95°F)

Operating humidity

35% to 85% (no condensation)

Storage temperature

–20°C to +60°C (–4°F to +140°F)

Storage humidity

10% to 90%

Supplied accessories

Remote Commander (1)

Lithium battery CR2025 (1)

HD D-sub 15 pin cable (1.8 m) (1)

(1-832-428-11, SONY)

Carrying case (1)

AC power cord (1)

Operating Instructions (CD-ROM)

(1)

Quick Reference Manual (1)

Safety Regulations (1)

Security Label (1)

Design and specifications are subject to change without notice.

50

Specifications

Note

Always verify that the unit is operating properly before use. SONY WILL NOT BE LIABLE FOR

DAMAGES OF ANY KIND INCLUDING, BUT

NOT LIMITED TO, COMPENSATION OR

REIMBURSEMENT ON ACCOUNT OF THE

LOSS OF PRESENT OR PROSPECTIVE

PROFITS DUE TO FAILURE OF THIS UNIT,

EITHER DURING THE WARRANTY PERIOD

OR AFTER EXPIRATION OF THE

WARRANTY, OR FOR ANY OTHER REASON

WHATSOEVER.

Optional accessories

Projector Lamp

LMP-E190(for replacement)

Some of the items may not be available in some areas. For details, please consult your nearest Sony dealer.

Pin assignment

INPUT A connector (HD D-sub 15-pin, female)

INPUT B connector (HD D-sub 15-pin, female) (VPL-EX50 only)

1

4

5

2

3

6

7

8

R 9

G

B

10

11

RESERVE 12

GND 13

GND (R)

GND (G)

GND (B)

14

15

Power supply input for DDC

GND

GND

DDC/SDA

HD

VD

DDC/SCL

RS-232C connector (D-sub 9 pin, female) (VPL-EW5/EX50/EX5 only)

1

4

5

2

3

6

7

8

R/R-Y 9

G/Y

B/B-Y

GND (R)

GND (G)

GND (B)

10

11

RESERVE 12

GND 13

14

15

Power supply input for DDC

GND

GND

DDC/SDA

HD

VD

DDC/SCL

3

4

5

1

2

NC

RXDA

TXDA

DTR

GND

8

9

6

7

NC

RTS

CTS

NC

Specifications

51

37

38

39

40

33

34

35

36

41

42

43

44

29

30

31

32

25

26

27

28

21

22

23

24

7

8

10

11

1080/60i

1080/50i

720/60p

720/50p

640

× 350

640

× 400

640

× 480

800

× 600

832

× 624

1024

× 768

1152

× 864

1152

× 900

52

Specifications

Preset signals

3

4

1

2

5

Memory

No.

Preset signal

Video 60 Hz

Video 50 Hz

480/60i

575/50i

480/60p

6 575/50p

60 Hz

50 Hz

480/60i

575/50i

480/60p (Progressive component NTSC)

575/50p (Progressive component PAL)

1035/60i, 1080/60i

1080/50i

720/60p

720/50p

VGA mode 1

VGA VESA 85 Hz

PC-9801 Normal

VGA mode 2

VGA VESA 85 Hz

VGA mode 3

Macintosh 13"

VGA VESA 72 Hz

VGA VESA 75 Hz

VGA VESA 85 Hz

SVGA VESA 56 Hz

SVGA VESA 60 Hz

SVGA VESA 72 Hz

SVGA VESA 75 Hz

SVGA VESA 85 Hz

Macintosh 16"

XGA VESA 60 Hz

XGA VESA 70 Hz

XGA VESA 75 Hz

XGA VESA 85 Hz

SXGA VESA 70 Hz

SXGA VESA 75 Hz

SXGA VESA 85 Hz

Sunmicro LO

fV (Hz)

59.940

50.000

59.940

50.000

60.000

50.000

72.188

75.000

85.061

74.550

60.004

70.069

75.029

84.997

70.019

75.000

85.057

65.960

85.080

59.940

66.667

72.809

75.000

85.008

56.250

60.317

60.000

50.000

60.000

50.000

70.086

85.080

56.416

70.086

31.250

48.077

46.875

53.674

49.724

48.363

56.476

60.023

68.677

63.995

67.500

77.487

61.795

37.861

31.469

35.000

37.861

37.500

43.269

35.156

37.879

33.750

28.130

45.000

37.500

31.469

37.861

24.823

31.469

fH (kHz)

15.734

15.625

15.734

15.625

31.470

Sync

S on G/Y

S on G/Y

–

–

S on G/Y

S on G/Y

H-pos, V-pos

H-pos, V-pos

H-pos, V-pos

H-neg, V-neg

H-neg, V-neg

H-neg, V-neg

H-pos, V-pos

H-pos, V-pos

H-pos, V-pos

H-pos, V-pos

H-pos, V-pos

H-neg, V-neg

S on G/Y

S on G/Y

S on G/Y

S on G/Y

H-pos, V-neg

H-pos, V-neg

H-neg, V-neg

H-neg, V-pos

H-neg, V-pos

H-neg, V-neg

H-neg, V-neg

H-neg, V-neg

H-neg V-neg

H-neg V-neg

H-pos, V-pos

H-pos, V-pos

56

60

61

49

50

55

63

46

47

48

Memory

No.

45

Preset signal

1280

× 960

1280

1280

× 1024

1400

× 1050

1280

× 768

× 720

1360 × 768

1440 × 900

1280 × 800

SXGA VESA 60 Hz

SXGA VESA 75 Hz

SXGA VESA 60 Hz

SXGA VESA 75 Hz

SXGA VESA 85 Hz

SXGA+ 60 Hz

WXGA 60Hz

WXGA 60Hz

1360 × 768/60

1440 × 900/60

1280 × 800/60

fH (kHz)

60.000

75.000

63.974

79.976

91.146

65.317

47.776

44.772

44.720

55.935

49.702

fV (Hz)

60.000

75.000

60.013

75.025

85.024

59.978

59.870

59.885

59.799

59.887

59.810

Sync

H-pos, V-pos

H-pos, V-pos

H-pos, V-pos

H-pos, V-pos

H-pos, V-pos

H-neg, V-pos

H-neg, V-pos

H-neg, V-pos

H-neg, V-pos

H-neg, V-pos

H-neg, V-pos

Notes

• The receivable digital signals are preset signals of Memory No. 3 to 11, 26, 32, 37, 45, 50, 55 and

56 (VPL-EW5 only).

• When a signal other than the preset signals shown above is input, the picture may not be displayed properly.

• When an SXGA+ signal is input, the image may extend beyond the edges of the screen. In this case, input a signal with no black edges around the image, and disconnect and reconnect the cable or select the input signal by pressing the INPUT key.

Specifications

53

Installation Diagram

Floor Installation (Front Projection)

Wall

Distance between the front of the cabinet and the center of the lens

Foremost part of the cabinet

Front of the lens

14.6 (

19

/

32

)

Center of the lens

Center of the screen

Floor

Unit: mm (inches)

*

Adjuster not stretched, and the V Keystone function has been done.

This section describes the examples of installing the projector on a desk, etc.

See the chart on page 55 concerning the installation measurements.

The alphabetical letters in the illustration indicate the distances below.

a: distance between the screen and the center of the lens

b: distance between the floor and the center of the lens

c: distance between the floor and the bottom of the adjusters of the projector

x: distance between the floor and the center of the screen (free)

54

Installation Diagram

VPL-EX50/EX5/ES5

PS 40 a N

1180

(46

1

/

2

)

M 1330

(52

3

/

8

)

b c

60

1780

(70

1

/

8

)

2020

(79

5

/

8

)

80 100 120 150 180 200

2390

(94

1

/

8

)

2700

(106

3

/

8

)

2990

(117

3

/

4

)

3600

(141

3

/

4

)

4510

(177

5

/

8

)

5410

(213

1

/

8

)

6020

(237

1

/

8

)

3380

(133

1

/

8

)

4070

(160

3

/

8

)

5090

(200

1

/

2

)

6110

(240

5

/

8

)

Based on the calculation formula given below.

6800

(267

3

/

4

)

Based on the calculation formula given below.

a (N) = {(PS × 29.376) × 1.03} – 31.7

a (M) = {(PS × 35.202) × 0.97} – 31.7

b = x – {PS × 5.055 + (a + 31.7) × 0.1405 – 4.5} c = x – {PS × 5.055+ (a + 31.7) × 0.1405 – 4.5 + 90.5}

Unit: mm (inches)

250 300

7530

(296

1

/

2

)

8500

(334

3

/

4

)

9050

(356

3

/

8

)

10210

(402

1

/

8

)

VPL-EW5

(When “Aspect” on the Signal menu is set to “Full 2”)

PS 40 a N

1250

(49

1

/

4

)

M 1410

(55

5

/

8

)

b c

60

1890

(74

1

/

2

)

2140

(84

3

/

8

)

80 100 120 150 180 200

2530

(99

5

/

8

)

2860

(112

5

/

8

)

3170

(124

3580

(141)

7

/

8

)

3810

(150

4300

(169

1

3

/

/

8

8

)

)

4770

(187

5390

(212

7

1

/

/

8

4

)

)

5730

(225

6470

(254

5

7

/

/

8

8

)

)

6370

(250

7

/

8

)

7200

(283

Based on the calculation formula given below.

1

/

2

)

Based on the calculation formula given below.

a (N) = {(PS × 31.076) × 1.03} – 31.7

a (M) = {(PS × 37.252) × 0.97} – 31.7

b = x – {PS × 4.465 + (a + 31.7) × 0.1405 – 4.5} c = x – {PS × 4.465 + (a + 31.7) × 0.1405 – 4.5 + 90.5}

Unit: mm (inches)

250 300

7970

(313

7

/

8

)

9000

(354

3

/

8

)

9570

(376

7

/

8

)

10810

(425

3

/

4

)

Notes for VPL-EW5

• The projected image size is the one when “Aspect” on the Signal menu is set to “Full 2”. When

“Aspect” on the Signal menu is set to other than “Full 2”, black bands may appear at the top and bottom or right and left of the screen.

• When “Aspect” in the Signal menu is set to “4:3”, the projected image size (diagonal) will be approximately 88 % of “Full 2” size.

• When “Aspect” in the Signal menu is set to “16:9”, the projected image size (diagonal) will be approximately 97 % of “Full 2” size.

The alphabetical letters in the charts and calculation methods indicate the following.

PS: projected image size measured diagonally (inches)

a:

distance between the screen and the center of the lens

b:

distance between the floor and the center of the lens

c:

distance between the floor and the adjusters of the projector

x:

free

N: minimum

M: maximum

Installation Diagram

55

Ceiling Installation (Front Projection)

The unit is set so that the bottom is parallel to the ceiling.

3

1

5

Center of the screen

Center of the lens

Center of the Projector

Holes for mounting a projector suspension support

Ceiling

Center of the lens

Center of the screen

Foremost part of the cabinet

10.4 (

3

/

8

)

26.7 (1)

Center of the lens

Hole for mounting a projector suspension support (front)

Center of the lens

Distance between the front of the cabinet and the hole for mounting a projector suspension support (front)

Unit: mm (inches)

This section describes the examples for installing the projector on the ceiling.

When installing the projector on the ceiling, use a Projector Suspension Support recommended by Sony.

For ceiling installation, ask for qualified Sony personnel.

See the chart on page 57 concerning the installation measurements.

The alphabetical letters in the illustrations indicate the distances below.

a’: distance between the hole (front) for mounting a projector suspension support on bottom surface of this projector and the center of the screen

b: distance between the hole (front) for mounting a projector suspension support on bottom surface of this projector and the ceiling

x: distance between the ceiling and the center of the screen

56

Installation Diagram

VPL-EX50/EX5/ES5

PS 40 a’ N

1200

(47

1

/

4

)

M 1350

(53

1

/

4

)

x b

60

1800

(70

7

/

8

)

2040

(80

3

/

8

)

80 100 120 150 180 200

2410

(95)

3010

(118

5

/

8

)

3620

(142

5

/

8

)

4530

(178

3

/

8

)

5440

(214

1

/

4

)

6040

(237

7

/

8

)

2720

(107

1

/

8

)

3410

(134

3

/

8

)

4090

(161

1

/

8

)

5120

(201

5

/

8

)

6140

(241

7

/

8

)

Based on the calculation formula given below.

6830

(269)

Free a’(N) = {(PS × 29.415) × 1.03} - 32.0 + 16.4

a’(M) = {(PS × 35.283) × 0.97} - 32.0 + 16.4

x = b + {PS × 5.073 + (a’+ 32.0 - 16.4) × 0.07344 - 2.3 + 72.5}

Unit: mm (inches)

250 300

7560

(297

3

/

4

)

8540

(336

3

/

8

)

9070

(357

1

/

4

)

10250

(403

5

/

8

)

VPL-EW5

(When “Aspect” on the Signal menu is set to “Full 2”)

x b

PS 40 a’ N

1270

(50)

M 1430

(56

3

/

8

)

60

1910

(75

1

/

4

)

2160

(85

1

/

8

)

80 100 120 150 180 200

2550

(100

1

/

2

)

2880

(113

1

/

2

)

3190

(125

3610

(142

5

1

/

/

8

4

)

)

3830

(150

(170

7

4330

1

/

8

/

)

2

)

4800

(189)

5420

(213)

5760

(226

6510

(256

7

3

/

/

8

8

)

)

6400

(252)

7230

(284

3

/

4

)

Based on the calculation formula given below.

Free a’(N) = {(PS × 31.147) × 1.03} – 32.0 + 16.4

a’(M) = {(PS × 37.367) × 0.97} – 32.0 + 16.4

x = b + {PS × 4.481 + (a’+ 32.0 – 16.4) × 0.07344 – 2.3 + 72.5}

Unit: mm (inches)

250 300

8000

(315)

9050

(356

3

/

8

)

9610

(378

1

/

2

)

10860

(427

5

/

8

)

Notes for VPL-EW5

• The projected image size is the one when “Aspect” on the Signal menu is set to “Full 2”. When

“Aspect” on the Signal menu is set to other than “Full 2”, black bands may appear at the top and bottom or right and left of the screen.

• When “Aspect” in the Signal menu is set to “4:3”, the projected image size (diagonal) will be approximately 88 % of “Full 2” size.

• When “Aspect” in the Signal menu is set to “16:9”, the projected image size (diagonal) will be approximately 97 % of “Full 2” size.

The alphabetical letters in the charts and calculation methods indicate the following.

PS: projected image size measured diagonally (inches)

a’: distance between the hole (front) for mounting a projector suspension support on bottom surface of this projector and the center of the screen

b:

distance between the projector suspension support mounting surface on bottom of this projector and the ceiling

x:

distance between the center of the screen and the ceiling

N: minimum

M: maximum

Installation Diagram

57

Dimensions

Front

314 (12

3

/

8

)

69.5 (2

5

/

8

)

Center of the projector

7

3

Unit: mm (inches)

Side

269 (10

5

/

8

)

3

Unit: mm (inches)

58

Dimensions

Top

5

314 (12

3

/

8

)

Unit: mm (inches)

Dimensions

59

Index

A

Adjust Picture .......................................... 31

Air filter ................................................... 44

Aspect ............................................... 33, 34

Auto Input Search ................................... 35

B

Background ............................................. 38

Batteries .................................................. 16

Brightness ............................................... 31

C

Color ....................................................... 31

Color System ........................................... 35

Color Temp. ............................................ 31

Connecting a computer ........................... 19

Connecting a VCR .................................. 21

Contrast ................................................... 31

D

DDE ........................................................ 32

Digital Zoom function ............................. 27

Direct Power On ...................................... 38

Direct power On/Off function ................. 27

Dot Phase ................................................ 33

F

fH (Horizontal Frequency) ...................... 40 fV (Vertical Frequency) .......................... 40

G

Gamma Mode .......................................... 31

H

H Size ...................................................... 33

High Altitude Mode ................................ 38

Hue .......................................................... 31

I

Image Flip ............................................... 38

Input-A Signal Sel. .................................. 35

Installation ............................................... 17

notes ...................................................... 6

unsuitable conditions ............................. 7

unsuitable installation ............................ 6

60

Index

IR Receiver ..............................................36

L

Lamp Mode .............................................38

Lamp replacement ...................................42

Lamp Timer .............................................40

Lamp Timer Reset ...................................36

Language .................................................37

selecting the menu language ................25

Lens .........................................................11

Location and function of controls

connector panel ....................................14

control panel ........................................12

rear/bottom ...........................................10

Remote Commander ............................15

top/right side/front ...............................10

M

Menu

clearing the menu display ....................30

INFORMATION Menu .......................40

INPUT SETTING menu ......................33

INSTALL SETTING menu .................38

MENU SETTING menu ......................37

PICTURE SETTING menu .................31

SET SETTING menu ...........................35

using a menu ........................................29

Menu Position ..........................................37

Message List

caution ..................................................48

warning ................................................47

O

Optional accessories ................................51

P

Panel Key Lock ........................................36

Picture Mode ...........................................31

Pin assignment .........................................51

Power

turn on ..................................................22

Power Saving ...........................................36

Presentation .............................................27

Preset Memory No. ..................................34

Projecting .................................................22

R

Remote Commander ................................15

front remote control detector .........10, 36

location and function of controls .........15

rear remote control detector .................36

Reset

resetting an item ..................................30

RS-232C connector .................................51

S

Screen size .........................................17, 18

Security bar .............................................11

Security Lock ....................................26, 38

Security lock ............................................11

Sharpness .................................................31

Shift .........................................................33

Smart APA ...............................................35

Specifications ..........................................49

Standby Mode .........................................36

Start Up Image ........................................37

Status .......................................................37

Supplied accessories ................................50

T

Troubleshooting .......................................45

V

V Keystone ..............................................38

Volume ....................................................32

Index

61

Sony Corporation