advertisement
User Manual
EB40D EB48D
The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance.
Recommended hours of use per day of this product is under 16 hours.
If the product is used for longer than 16 hours a day, the warranty may be void.
Table of contents
Before Using the Product
Preparations
Connecting and Using a Source
Device
Connection using the D-SUB cable
Connection Using an HDMI Cable
Connection Using an HDMI-DVI Cable
Connection Using an HDMI-DVI Cable
Connection Using an HDMI Cable
Using MDC
MDC Program Installation/Uninstallation 41
Using MDC over RS232C connections and Wi-Fi 42
Screen Adjustment
If the input source is PC or HDMI
If the input source is TV, HDMI or AV 43
Backlight / Contrast / Brightness /
Sharpness / Color / Tint (G/R) 44
2
Table of contents
Sound Adjustment
Broadcasting
Network
Applications
MagicInfo Express Content Creator
Using MagicInfo Express Content Creator 90
3
Table of contents
Playing photos, videos and music
(Media Play)
Read the following before using media play with a USB device 91
Menu items in the media content list page
Available buttons and features during photo playback 95
Available buttons and features during video playback 96
Available buttons and features during music playback 97
Supported Subtitle and Media play file formats 98
Compatible image file format 98
System
Configuring settings for Multi Control 105
Source AutoSwitch Settings 118
Support
Troubleshooting Guide
Requirements Before Contacting Samsung
Checking the Resolution and Frequency
4
Table of contents
Specifications
Appendix
Responsibility for the Pay Service
A Product damage caused by customer's fault 140
Optimum Picture Quality and Afterimage
Prevention of Afterimage Burn-in
5
Chapter 01
Before Using the Product
Copyright
The contents of this manual are subject to change without notice to improve quality.
© 2014 Samsung Electronics
Samsung Electronics owns the copyright for this manual.
Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited.
Microsoft, Windows are registered trademarks of Microsoft Corporation.
VESA, DPM and DDC are registered trademarks of the Video Electronics Standards Association.
Ownership of all other trademarks is attributed to their due owner.
6
Safety Precautions
Caution
RISK OF ELECTRIC SHOCK DO NOT OPEN
Caution : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. (OR BACK)
THERE ARE NO USER SERVICEABLE PARTS INSIDE.
REFER ALL SERVICING TO QUALIFIED PERSONNEL.
This symbol indicates that high voltage is present inside.
It is dangerous to make any kind of contact with any internal part of this product.
This symbol alerts you that important literature concerning operation and maintenance has been included with this product.
Symbols
Warning
A serious or fatal injury may result if instructions are not followed.
Caution
Personal injury or damage to properties may result if instructions are not followed.
Activities marked by this symbol are prohibited.
Instructions marked by this symbol must be followed.
Cleaning
― Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched.
― Take the following steps when cleaning.
― The following images are for reference only. Real-life situations may differ from what is shown in the images.
1 Power off the product and computer.
2 Disconnect the power cord from the product.
― Hold the power cable by the plug and do not touch the cable with wet hands. Otherwise, an electric shock may result.
3 Wipe the product with a clean, soft and dry cloth.
• Do not use detergents that contain alcohol, solvent or surface-active agents.
!
• Do not spray water or detergent directly on the product.
4 Wet a soft and dry cloth in water and wring thoroughly to clean the exterior of the product.
5
Connect the power cord to the product when cleaning is finished.
6
Power on the product and computer.
7
Storage
Due to the characteristics of high-glossy products, using a UV humidifier nearby may create whitecolored stains on the product.
― Contact Customer Service Center if the inside of the product needs cleaning (service fee will be charged).
Electricity and Safety
― The following images are for reference only. Real-life situations may differ from what is shown in the images.
Warning
Do not use a damaged power cord or plug, or a loose power socket.
• An electric shock or fire may result.
!
Do not use multiple products with a single power socket.
• Overheated power sockets may cause a fire.
Do not touch the power plug with wet hands. Otherwise, an electric shock may result.
!
Insert the power plug all the way in so it is not loose.
• An unsecure connection may cause a fire.
!
Connect the power plug to a grounded power socket (type 1 insulated devices only).
• An electric shock or injury may result.
Do not bend or pull the power cord with force. Be careful not to leave the power cord under a heavy object.
• Damage to the cord may result in a fire or electric shock.
Do not place the power cord or product near heat sources.
• A fire or electric shock may result.
Clean any dust around the pins of the power plug or the power socket with a dry cloth.
• A fire may result.
8
Caution
!
!
!
Do not disconnect the power cord while the product is being used.
• The product may become damaged by an electric shock.
Only use the power cord provided with your product by Samsung. Do not use the power cord with other products.
• A fire or electric shock may result.
Keep the power socket where the power cord is connected unobstructed.
• The power cord must be disconnected to cut off power to the product when an issue occurs.
• Note that the product is not completely powered down by using only the power button on the remote.
Hold the plug when disconnecting the power cord from the power socket.
• An electric shock or fire may result.
!
Installation
Warning
DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP OF
THE PRODUCT. DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES.
• A fire may result.
Have a technician install the wall-mount hanger.
• Installation by an unqualified person can result in an injury.
• Only use approved cabinets.
Do not install the product in poorly ventilated spaces such as a bookcase or closet.
• An increased internal temperature may cause a fire.
Install the product at least 10 cm away from the wall to allow ventilation.
• An increased internal temperature may cause a fire.
!
Keep the plastic packaging out of the reach of children.
• Children may suffocate.
!
9
!
!
!
Bend and keep part of the outdoor TV antenna cable hanging downwards
(the part inside the room) to prevent rainwater from entering the product.
• If rainwater enters the product, a fire or electric shock can occur.
When using an outdoor antenna, be sure to install the antenna away from nearby power lines to prevent the antenna from collapsing onto them in strong winds.
• A collapsed antenna can cause an electric shock or injury.
Do not install the product on an unstable or vibrating surface (insecure shelf, sloped surface, etc.)
• The product may fall and become damaged and/or cause an injury.
• Using the product in an area with excess vibration may damage the product or cause a fire.
Do not install the product in a vehicle or a place exposed to dust, moisture
(water drips, etc.), oil, or smoke.
• A fire or electric shock may result.
Do not expose the product to direct sunlight, heat, or a hot object such as a stove.
• The product lifespan may be reduced or a fire may result.
Do not install the product within the reach of young children.
• The product may fall and injure children.
• As the front is heavy, install the product on a flat and stable surface.
Edible oil, such as soybean oil, can damage or deform the product. Do not install the product in a kitchen or near a kitchen counter.
10
Caution
!
Do not drop the product while moving.
• Product failure or personal injury may result.
Do not set down the product on its front.
• The screen may become damaged.
When installing the product on a cabinet or shelf, make sure that the bottom edge of the front of the product is not protruding.
• The product may fall and become damaged and/or cause an injury.
• Install the product only on cabinets or shelves of the right size.
Set down the product gently.
• Product failure or personal injury may result.
!
!
!
!
SAMSUNG
Installing the product in an unusual place (a place exposed to a lot of fine dust, chemical substances, extreme temperatures or a significant presence of moisture, or a place where the product will operate continuously for an extended period of time) may seriously affect its performance.
• Be sure to consult Samsung Customer Service Center if you want to install the product at such a place.
Operation
Warning
There is a high voltage inside the product. Never disassemble, repair or modify the product yourself.
• A fire or electric shock may result.
• Contact Samsung Customer Service Center for repairs.
To move the product, first disconnect all the cables from it, including the power cable.
• Damage to the cord may result in a fire or electric shock.
If the product generates abnormal sounds, a burning smell or smoke, disconnect the power cord immediately and contact Samsung Customer
Service Center.
• An electric shock or fire may result.
Do not let children hang from the product or climb on top of it.
• Children may become injured or seriously harmed.
If the product is dropped or the outer case is damaged, turn off the power switch and disconnect the power cord. Then contact Samsung Customer
Service Center.
• Continued use can result in a fire or electric shock.
11
!
!
!
Do not leave heavy objects or items that children like (toys, sweets, etc.) on top of the product.
• The product or heavy objects may fall as children try to reach for the toys or sweets resulting in a serious injury.
During a lightning or thunderstorm, remove the power cable and do not touch the antenna cable.
• A fire or electric shock may result.
!
Do not drop objects on the product or apply impact.
• A fire or electric shock may result.
100
GAS
Do not move the product by pulling the power cord or any cable.
• Product failure, an electric shock or fire may result from a damaged cable.
If a gas leakage is found, do not touch the product or power plug. Also, ventilate the area immediately.
• Sparks can cause an explosion or fire.
Do not lift or move the product by pulling the power cord or any cable.
• Product failure, an electric shock or fire may result from a damaged cable.
Do not use or keep combustible spray or an inflammable substance near the product.
• An explosion or fire may result.
Ensure the vents are not blocked by tablecloths or curtains.
• An increased internal temperature may cause a fire.
Do not insert metallic objects (chopsticks, coins, hairpins, etc) or objects that burn easily (paper, matches, etc) into the product (via the vent or input/ output ports, etc).
• Be sure to power off the product and disconnect the power cord when water or other foreign substances have entered the product.
Then contact Samsung Customer Service Center.
• Product failure, an electric shock or fire may result.
Do not place objects containing liquid (vases, pots, bottles, etc) or metallic objects on top of the product.
• Be sure to power off the product and disconnect the power cord when water or other foreign substances have entered the product.
Then contact Samsung Customer Service Center.
• Product failure, an electric shock or fire may result.
12
!
!
Caution
!
!
-_-
Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage burn-in or defective pixels.
• Activate power-saving mode or a moving-picture screen saver if you will not be using the product for an extended period of time.
Disconnect the power cord from the power socket if you do not plan on using the product for an extended period of time (vacation, etc).
• Dust accumulation combined with heat can cause a fire, electric shock or electric leakage.
Use the product at the recommended resolution and frequency.
• Your eyesight may deteriorate.
!
!
Do not hold the product upside-down or move it by holding the stand.
• The product may fall and become damaged or cause an injury.
!
Looking at the screen too close for an extended period of time can deteriorate your eyesight.
Do not use humidifiers or stoves around the product.
• A fire or electric shock may result.
Rest your eyes for more than 5 minutes for every 1 hour of product use.
• Eye fatigue will be relieved.
Do not touch the screen when the product has been turned on for an extended period of time as it will become hot.
Store small accessories out of the reach of children.
Exercise caution when adjusting the product angle or stand height.
• Your hand or finger may get stuck and injured.
• Tilting the product at an excessive angle may cause the product to fall and an injury may result.
Do not place heavy objects on the product.
• Product failure or personal injury may result.
13
!
!
Be careful that children do not place the battery in their mouths when removed from the remote control. Place the battery in a location that children or infants cannot reach.
• If children have had the battery in their mouths, consult your doctor immediately.
When replacing the battery, insert it with the right polarity (+, -).
• Otherwise, the battery may become damaged or it may cause fire, personal injury or damage due to leakage of the internal liquid.
Use only the specified standardized batteries, and do not use a new battery and a used battery at the same time.
• Otherwise, the batteries may be damaged or cause fire, personal injury or damage due to a leakage of the internal liquid.
The batteries (and rechargeable batteries) are not ordinary refuse and must be returned for recycling purposes. The customer is responsible for returning the used or rechargeable batteries for recycling.
• The customer can return used or rechargeable batteries to a nearby public recycling center or to a store selling the same type of the battery or rechargeable battery.
14
Chapter 02
Preparations
Checking the Components
Contact the vendor where you purchased the product if any components are missing.
The appearance of the components and items sold separately may differ from the image shown.
Components
― Components may differ in different locations.
Quick Setup Guide
Warranty card
(Not available in some locations)
Regulatory guide
RS232C-Stereo cable Stand base Remote Control
Stand neck
Power cord
Batteries
(Not available in some locations)
15
The following items can be purchased at your nearest retailer.
Items sold separately
HDMI cable HDMI-DVI cable Video cable Audio cable RCA stereo cable
Stereo cable
16
Parts
Control Panel
RS232C IN
VIDEO AUDIO
HDMI IN
(DVI)
ANT IN
RGB / DVI
AUDIO IN
CABLE AIR
RGB IN
Speaker
Panel Key
POWER
Remote sensor
― The color and shape of parts may differ from what is shown.
Specifications are subject to change without notice to improve quality.
Panel Key
Buttons Description
Power on the product.
If you press the button when the product is turned on, the control menu will be displayed.
― To exit the OSD menu, press and hold the panel key for at least one second.
Move to the upper or lower menu. You can also adjust the value of an option.
Change the channel in TV mode.
Remote sensor
Move to the left or right menu.
― You can adjust the volume by moving the panel key left or right when the control menu is not displayed.
Press a button on the remote control pointing at the sensor on the front of the product to perform the corresponding function.
― Using other display devices in the same space as the remote control of this product can cause the other display devices to be inadvertently controlled.
Use the remote control within 7 m to 10 m from the sensor on the product at an angle of 30 from the left and right.
― Store used batteries out of reach of children and recycle.
― Do not use a new and used battery together. Replace both batteries at the same time.
― Remove batteries when the remote control is not to be used for an extended period of time.
17
― If you press the button on the panel key when the product is turned on, the control menu will be displayed.
Control menu
Buttons
Return
Source
Menu
MagicInfo
Power Off
Return
Description
Select the connected input source.
Move the panel key right to select Source in the control menu.
When the list of input sources is displayed, move the panel key up or down to select the desired input source. Next, press the panel key.
Display the OSD menu.
Move the panel key left to select Menu in the control menu. The OSD control screen will appear. Move the panel key right to select the desired menu.
You can select a sub-menu item by moving the panel key up, down, left, or right.
To change settings, select the desired menu and press the panel key.
Enter MagicInfo mode.
Move the panel key up to select MagicInfo in the control menu.
Power off the product.
Move the panel key down to select Power Off in the control menu.
Next, press the panel key.
Exit the control menu.
18
Reverse Side
― The color and shape of parts may differ from what is shown.
Specifications are subject to change without notice to improve quality.
RS232C IN
VIDEO AUDIO R
HDMI IN
(DVI)
ANT IN
CABLE AIR
RGB IN
Port
USB
RS232C IN
(5V 0.5A) / CLONING
AV IN VIDEO / L-AUDIO-R
RGB / DVI AUDIO IN
HDMI IN (DVI)
ANT IN CABLE / AIR
RGB IN
Description
Connect to a USB memory device.
Connects to MDC using an RS232C adapter.
Connect to an external device using a video or Audio cable.
Receives sound from a PC via an audio cable.
Connects to a source device using a HDMI cable or HDMI-DVI cable.
Connect to an antenna cable.
Connects to a source device using a D-SUB cable.
VIDEO L AUDIO R
RS232C IN
ANT IN
RGB / DVI
AUDIO IN
CABLE AIR
RGB IN
HDMI IN
(DVI)
19
Anti-theft Lock
― An anti-theft lock allows you to use the product securely even in public places.
― The locking device shape and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft locking device for details.
― The following images are for reference only. Real-life situations may differ from what is shown in the images.
To lock an anti-theft locking device:
1
Fix the cable of your anti-theft locking device to a heavy object such as a desk.
2
Put one end of the cable through the loop on the other end.
3
Insert the locking device into the anti-theft lock slot at the back of the product.
4
Lock the locking device.
An anti-theft locking device can be purchased separately.
Refer to the user guide provided with your anti-theft locking device for details.
Anti-theft locking devices can be purchased at electronics retailers or online.
20
Remote Control
― Using other display devices in the same space as the remote control of this product can cause the other display devices to be inadvertently controlled.
― A button without a description in the image below is not supported on the product.
Turns the product On/Off.
Press to select additional channels (digital) being broadcasted by the same station. For example, to select channel
“54-3”, press “54”, then press “-” and “3”.
Adjust the volume.
Change the input source.
Display or hide the onscreen display menu, or return to the previous menu.
.QZ
1
GHI
4
PRS
7
DEL-/--
VOL
ABC
2
JKL
5
TUV
8
SYMBOL
0
MUTE
POWER
OFF
DEF
3
MNO
6
WXY
9
CH LIST
CH
SOURCE
MENU
HOME
MagicInfo
Player I
Power off the product.
Number buttons
Enter the password in the OSD menu.
Channel List Launch Button.
Mute the sound.
Unmuting the sound: Press MUTE again or press the volume control(+ VOL -) button.
Remote control button functions may differ for different products.
Change the channel in TV mode.
MagicInfo Player Launch Button.
MagicInfo Player Launch Button.
21
TOOLS INFO
Quickly select frequently used functions.
Return to the previous menu.
It sets safe lock function.
Not Available.
RETURN EXIT
PC
A
DVI
B
HDMI
C
SET
IR control
UNSET LOCK
DP
D
Display information about the current input source.
Move to the upper, lower, left or right menu, or adjust an option's setting.
Confirm a menu selection.
Exit the current menu.
In TV mode, configure settings such as the program guide for digital channels. In other modes, manually select a connected source device.
Play photos, videos or music.
Remote control button functions may differ for different products.
To place batteries in the remote control
22
Before Installing the Product
(Installation Guide)
15 ˚
To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.
• Ensure that an authorized installation company installs the wall mount.
• Otherwise, it may fall and cause personal injury.
• Make sure to install the specified wall mount.
Tilting Angle and Rotation
― Contact Samsung Customer Service Center for further details.
• The product can be tilted at a maximum angle of 15˚ from a perpendicular wall surface.
• To use the product vertically (portrait), turn it clockwise so that the LED is pointing down.
Ventilation
Installation on a Perpendicular Wall
A Minimum 4 cm
B Ambient temperature: Under 35 C
• When installing the product on a perpendicular wall, allow at least 4 cm of space between the product and wall surface for ventilation and ensure that the ambient A temperature is kept below 35 C.
A
B
Figure 1.1 Side view
23
B
A
E
C
Figure 1.2 Side view
Dimensions
2
1
Figure 1.3 Side view
D
4
3
D
Installation on an Indented Wall
― Contact Samsung Customer Service Center for further details.
Plane view
A Minimum 4 cm
B Minimum 7 cm
C Minimum 5 cm
D Minimum 5 cm
E Ambient temperature: Under 35 C
― When installing the product on an indented wall, allow at least the space specified above between the product and wall for ventilation and ensure that the ambient temperature is kept below 35 C.
5
Unit: cm
Model name
1 1 2 2 3 3 4 4 5
EB40D 91.42
88.82
50.07
54.79
9.09
EB48D 108.32
105.62
59.51
63.78
9.09
― All drawings are not necessarily to scale. Some dimensions are subject to change without prior notice.
Refer to the dimensions prior to performing installation of your product. Not responsible for typographical or printed errors.
24
Installing the Wall Mount
Installing the Wall Mount Kit
The wall mount kit (sold separately) allows you to mount the product on the wall.
For detailed information on installing the wall mount, see the instructions provided with the wall mount.
We recommend you contact a technician for assistance when installing the wall mount bracket.
Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you elect to install the wall mount on your own.
25
Wall Mount Kit Specifications
― Install your wall mount on a solid wall perpendicular to the floor. Before attaching the wall mount to surfaces other than plaster board, please contact your nearest dealer for additional information.
If you install the product on a slanted wall, it may fall and result in severe personal injury.
• Samsung wall mount kits contain a detailed installation manual and all parts necessary for assembly are provided.
• Do not use screws that are longer than the standard length or do not comply with the VESA standard screw specifications. Screws that are too long may cause damage to the inside of the product.
• For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ depending on the wall mount specifications.
• Do not fasten the screws too firmly. This may damage the product or cause the product to fall, leading to personal injury.
Samsung is not liable for these kinds of accidents.
• Samsung is not liable for product damage or personal injury when non-specified wall mount is used or the consumer fails to follow the product installation instructions.
• Do not mount the product at more than a 15 degree tilt.
• Always have two people mount the product on a wall.
• Standard dimensions for wall mount kits are shown in the table below.
Unit: cm
Model name Screw hole specs
(A * B) in centimeters
Standard Screw Quantity
EB40D
20 × 20 M8 / L14~16 4
EB48D
― Do not install your Wall Mount Kit while your product is turned on. It may result in personal injury due to electric shock.
26
Remote Control (RS232C)
Cable Connection
RS232C Cable
Interface
Pin
Bit rate
Data bits
Parity
Stop bit
Flow control
Maximum length
RS232C (9 pins)
TxD (No.2), RxD (No.3), GND (No.5)
9600 bps
8 bit
None
1 bit
None
15 m (only shielded type)
• Pin assignment
1 2 3 4 5
6
7
8
9
3
4
5
Pin
1
2
6 7 8 9
Signal
Detect data carrier
Received data
Transmitted data
Prepare data terminal
Signal ground
Prepare data set
Send request
Clear to send
Ring indicator
27
• RS232C cable
Connector: 9-Pin D-Sub to Stereo Cable
9 5
6
-P1-
1
-P1-
Female Rx
Tx
Gnd
-P1-
2
3
5
-------->
<--------
----------
-P2-
3
2
5
Tx
Rx
Gnd
-P2-
STEREO
PLUG
(3.5ø)
3
2
1
-P2-
Connection
• Connection 1
RS232C IN
28
Control Codes
Viewing control state (Get control command)
Header
0xAA
Command
Command type
ID Data length
0
Checksum
Controlling (Set control command)
Header Command ID Data length
0xAA Command type 1
Data
Value
Checksum
5
6
3
4
7
1
2
Command
No.
Command type
Power control
Volume control
8
Input source control
Screen mode control
Screen size control
PIP On/Off control
Auto adjustment control
Safety Lock
Command
0x11
0x12
0x14
0x18
0x19
0x3C
0x3D
0x5D
Value range
0~1
-
0~100
-
0~255
0~1
0
0~1
• All communications take place in hexadecimals. The checksum is calculated by adding up all values except the header. If a checksum adds up to be more than 2 digits as shown below
(11+FF+01+01=112), the first digit is removed.
E.g. Power On & ID=0
Header
0xAA
Command
0x11
ID Data length
1
Data 1
"Power"
Checksum
Header
0xAA
Command
0x11
ID Data length
1
Data 1
1
12
• To control all devices connected by a serial cable simultaneously irrespective of IDs, set the ID as
"0xFE" and transmit commands. Commands will be executed by each device but ACK will not respond.
29
Power control
• Function
A product can be powered on and off using a PC.
― The power on/off functions are not available on a Wi-Fi connection.
• Viewing power state (Get Power ON / OFF Status)
Header Command ID Data length Checksum
0xAA 0x11 0
• Setting power ON/Off (Set Power ON / OFF)
Header Command ID Data length
0xAA 0x11 1
Data
"Power"
"Power": Power code to be set on a product.
1: Power ON
0: Power OFF
• Ack
Header Command ID Data length
0xAA 0xFF 3
"Power": Power code to be set on a product.
• Nak
Header Command ID Data length
0xAA 0xFF 3
"ERR" : A code showing what error has occurred.
Ack/Nak
'A'
Ack/Nak
'N' r-CMD
0x11 r-CMD
0x11
Val1
"ERR"
Checksum
Val1
"Power"
Checksum
Checksum
Volume control
• Function
The volume of a product can be adjusted using a PC.
• Viewing volume state (Get Volume Status)
Header Command ID Data length
0xAA 0x12 0
Checksum
• Setting the volume (Set Volume)
Header Command ID
0xAA 0x12
Data length
1
"Volume": Volume value code to be set on a product. (0-100)
• Ack
Header Command ID Data length Ack/Nak
0xAA 0xFF 3 'A'
"Volume": Volume value code to be set on a product. (0-100)
• Nak
Header Command ID Data length Ack/Nak
0xAA 0xFF 3 'N'
Data
"Volume" r-CMD
0x12 r-CMD
0x12
Val1
"ERR"
Checksum
Val1
"Volume"
Checksum
Checksum
"ERR" : A code showing what error has occurred.
30
Input source control
• Function
The input source of a product can be changed using a PC.
• Viewing input source state (Get Input Source Status)
Header Command ID Data length Checksum
0xAA 0x14 0
• Setting the input source (Set Input Source)
Header Command ID Data length
0xAA 0x14 1
"Input Source": An input source code to be set on a product.
0x14 PC
Data
"Input Source"
0x0C Input source
0x40
0x21
0x22
0x23
DTV
HDMI1
HDMI1_PC
HDMI2
0x24
0x60
HDMI2_PC
MagicInfo
― This model does not support HDMI1_PC, HDMI2 and HDMI2_PC ports.
― MagicInfo is only available with models that contain the MagicInfo function.
Checksum
• Ack
Header
0xAA
Command
0xFF
ID Data length
3
Ack/Nak
'A' r-CMD
0x14
Val1
"Input
Source"
"Input Source": An input source code to be set on a product.
• Nak
Header Command ID Data length Ack/Nak
0xAA 0xFF 3 'N'
"ERR" : A code showing what error has occurred.
r-CMD
0x14
Val1
"ERR"
Checksum
Checksum
31
Screen mode control
• Function
The screen mode of a product can be changed using a PC.
― This control can only be used on models that include a TV.
― Displayed menus may vary depending on the region.
• Viewing screen status (Get Screen Mode Status)
Header Command ID Data length Checksum
0xAA 0x18 0
• Setting the picture size (Set Picture Size)
Header Command ID Data length
0xAA 0x18 1
Data
"Screen Mode"
"Screen Mode": A code that sets the product status
0x01 16 : 9
0x04
0x31
0x0B
Zoom
Wide Zoom
4 : 3
• Ack
Header
0xAA
Command
0xFF
ID Data length Ack/Nak
3 'A' r-CMD
0x18
Checksum
Val1
"Screen
Mode"
"Screen Mode": A code that sets the product status
Checksum
• Nak
Header
0xAA
Command
0xFF
ID Data length Ack/Nak
3 'N'
"ERR": A code showing what error has occurred r-CMD
0x18
Val1
"ERR"
Screen size control
• Function
The screen size of a product can be changed using a PC.
• Viewing the screen size (Get Screen Size Status)
Header Command ID Data length Checksum
0xAA 0x19 0
• Ack
Header Command ID Ack/Nak r-CMD
0xAA 0xFF
Data length
3 'A' 0x19
Val1
"Screen Size"
Checksum
Checksum
"Screen Size": product screen size (range: 0 – 255, unit: inch)
• Nak
Header Command ID Data length
Ack/Nak
0xAA 0xFF 3 'N' r-CMD
0x19
"ERR": A code showing what error has occurred
Val1
"ERR"
Checksum
32
PIP On/Off control
• Function
The PIP mode of a product can be turned on or off using a PC.
― Only available on models that have the PIP function.
― This function is not available in MagicInfo .
• Viewing PIP on/off state (Get the PIP ON / OFF Status)
Header Command ID Data length Checksum
0xAA 0x3C 0
• Setting PIP on/off (Set the PIP ON / OFF)
Header Command ID Data length
0xAA 0x3C 1
Data
"PIP"
"PIP": A code used to turn the PIP mode of a product on or off
1: PIP ON
0: PIP OFF
• Ack
Header Command ID Data length
Ack/Nak r-CMD
0xAA 0xFF 3 'A' 0x3C
Val1
"PIP"
Checksum
Checksum
"PIP": A code used to turn the PIP mode of a product on or off
• Nak
Header Command ID Data length
Ack/Nak r-CMD
0xAA 0xFF 3 'A' 0x3C
"ERR": A code showing what error has occurred
Val1
"PIP"
Checksum
Auto adjustment control (PC and BNC only)
• Function
Automatically adjust the PC system screen using a PC.
• Viewing auto adjustment state (Get Auto Adjustment Status)
None
• Setting auto adjustment (Set Auto Adjustment)
Header Command ID Data length Data
0xAA 0x3D 1 "Auto
Adjustment"
"Auto Adjustment" : 0x00 (at all times)
• Ack
Header Command ID Data length
0xAA 0xFF 3
Ack/Nak
'A' r-CMD
0x3D
Val1
Checksum
"Auto
Adjustment"
• Nak
Header
0xAA
Command
0xFF
ID Data length
3
"ERR": A code showing what error has occurred
Ack/Nak
'A' r-CMD
0x3D
Val1
"ERR"
Checksum
Checksum
33
Safety Lock
• Function
PC can be used to turn the Safety Lock function on or off on a product.
This control is available regardless of whether or not the power is turned on.
• Viewing the safety lock state (Get Safety Lock Status)
Header Command ID Data length Checksum
0xAA 0x5D 0
• Enabling or disabling safety lock (Set Safety Lock Enable / Disable)
Header Command ID Data length Data
0xAA 0x5D 1 "Safety Lock"
"Safety Lock": Safety lock code to be set on a product
1: ON
0: OFF
• Ack
Header Command ID Data length
Ack/Nak
0xAA 0xFF 3 'A' r-CMD
0x5D
Val1
Checksum
"Safety Lock"
"Safety Lock": Safety lock code to be set on a product
• Nak
Header Command ID Data length
Ack/Nak
0xAA 0xFF 3 'N'
"ERR": A code showing what error has occurred r-CMD
0x5D
Val1
"ERR"
Checksum
Checksum
34
Chapter 03
Connecting and Using a Source Device
Before Connecting
Pre-connection Checkpoints
― Before connecting a source device, read the user manual provided with it.
The number and locations of ports on source devices may differ from device to device.
― Do not connect the power cable until all connections are completed.
Connecting the power cable during connection may damage the product.
― Connect the sound ports correctly: left = white and right = red.
― Check the types of ports at the back of the product you want to connect.
Connecting to a PC
• Do not connect the power cable before connecting all other cables.
Ensure you connect a source device first before connecting the power cable.
• A PC can be connected to the product in a variety of ways.
Select a connection method suitable for your PC.
― Connecting parts may differ in different products.
Connection using the D-SUB cable (Analog type)
RGB IN
RGB / DVI AUDIO IN
35
Connection Using an HDMI Cable
HDMI IN (DVI)
Connection Using an HDMI-DVI Cable
― When you connect a PC to the product using an HDMI-DVI cable, set Edit Name to DVI PC to access video and audio content stored on the PC.
HDMI IN (DVI)
RGB / DVI AUDIO IN
36
Connecting to a Video Device
• Do not connect the power cable before connecting all other cables.
Ensure you connect a source device first before connecting the power cable.
• You can connect a video device to the product using a cable.
― Connecting parts may differ in different products.
― Press the SOURCE button on the remote control to change the source.
Connection Using the AV Cable
AV IN / VIDEO
AV IN / L-AUDIO-R
37
Connection Using an HDMI-DVI Cable
― Audio will not be enabled if the product is connected to a video device using an HDMI-DVI cable. To resolve this, additionally connect an audio cable to the audio ports on the product and video device.
When you connect a video device to the product using an HDMI-DVI cable, set Edit Name to DVI
Devices to access video and audio content stored on the video device.
― Supported resolutions include 1080p (50/60Hz), 720p (50/60Hz), 480p, and 576p.
HDMI IN (DVI)
Connection Using an HDMI Cable
Using an HDMI cable (up to 1080p)
• For better picture and audio quality, connect to a digital device using an HDMI cable.
• An HDMI cable supports digital video and audio signals, and does not require an audio cable.
• The picture may not display normally (if at all) or the audio may not work if an external device that uses an older version of HDMI mode is connected to the product. If such a problem occurs, ask the manufacturer of the external device about the HDMI version and, if out of date, request an upgrade.
• Be sure to use an HDMI cable with a thickness of 1.4 cm or less.
• Be sure to purchase a certified HDMI cable. Otherwise, the picture may not display or a connection error may occur.
• A basic high-speed HDMI cable or one with ethernet is recommended.
This product does not support the ethernet function via HDMI.
RGB / DVI AUDIO IN
HDMI IN (DVI)
38
Connecting the Antenna
― Connecting parts may differ in different products.
― When the product is powered on for the first time, basic settings are configured automatically.
― Take extra care to ensure the wires inside the antenna cable are not bent.
ANT IN CABLE / AIR
39
Initial Setup
After powering on the product for the first time, configure basic settings such as the language, channel and time.
Language → Regional Settings → Channel Source → Auto Tuning ( Auto Tuning does not appear if Set-top box or No TV (Signage Only) is selected.) → Network Settings → Clock → Setup Complete!
― Refer to
page 102 for details about the
Setup .
Changing the Input source
Source List
MENU m → Applications → Source List → ENTER E
Source
TV HDMI AV PC USB
The displayed image may differ depending on the model.
Source allows you to select a variety of sources and change source device names.
You can display the screen of a source device connected to the product. Select a source from source list to display the screen of the selected source.
― The input source can also be changed by using the SOURCE button on the remote control.
― The screen may not display correctly if an incorrect source is selected for the source device you want to convert to.
― To view detailed information about connected source devices, press the TOOLS button from the
Source page.
― If the product is in portrait orientation, it is not possible to change Source List .
― Refer to
for details about the Source List .
40
Chapter 04
Using MDC
The Multiple Display Control (MDC) software allows you to control display devices easily from a computer.
For details on how to use the MDC program, refer to Help after installing the program. The MDC program can be downloaded from the website.
MDC Program Installation/Uninstallation
Installation
MDC installation can be affected by the graphics card, mother board and network conditions.
1
Click the MDC Unified installation program.
2
Select a language for installation. Next, click " OK ".
3
When the " Welcome to the InstallShield Wizard for MDC_Unified " screen appears, click " Next ".
4
In the " License Agreement " window displayed, select " I accept the terms in the license agreement " and click " Next ".
5
In the displayed " Customer Information " window, fill out all the information fields and click
" Next ".
6
In the displayed " Destination Folder " window, select the directory path you want to install the program in and click " Next ".
― If the directory path is not specified, the program will be installed in the default directory path.
7
In the displayed " Ready to Install the Program " window, check the directory path to install the program in and click " Install ".
8
Installation progress will be displayed.
9
Click " Finish " in the displayed " InstallShield Wizard Complete " window.
― Select " Launch MDC Unified " and click " Finish " to run the MDC program immediately.
10 The MDC Unified shortcut icon will be created on the desktop after installation.
― The MDC execution icon may not be displayed depending on the PC system or product specifications.
― Press F5 if the execution icon is not displayed.
Uninstallation
1 Select Settings > Control Panel on the Start menu and double-click Add/Delete Program.
2 Select MDC Unified from the list and click Change/Remove.
41
Connecting to MDC
Using MDC over RS232C connections and Wi-Fi
Connect monitors using Wi-Fi and the RS232C IN ports on the monitors.
RS232C IN
Computer
Display 1
Display 2
42
Chapter 05
Screen Adjustment
Configure the Picture settings ( Backlight , Color Tone , etc.).
The layout of the Picture menu options may vary depending on the product.
Picture Mode
MENU m → Picture → Picture Mode → ENTER E
Select a picture mode ( Picture Mode ) suitable for the environment where the product will be used.
Different Picture Mode options are displayed depending on the current input source.
Picture
Picture Mode
· Backlight
· Contrast
· Brightness
· Sharpness
· Color
· Tint (G/R) G50
Information
55
100
45
50
50
R50
If the input source is PC or HDMI (when a PC is connected)
• Information : This mode reduces eye fatigue and is suitable for displaying information to the public.
• Advertisement : This mode is suitable for displaying video content and indoor/outdoor advertisements.
― These options can be selected only when Edit Name is set to PC .
(SOURCE → Source → TOOLS → Edit Name → ENTER E)
If the input source is TV, HDMI or AV
• Dynamic : This mode is suitable when the ambient light is bright.
• Standard : This mode is generally suitable for any environment.
• Movie : This mode reduces eye fatigue.
The displayed image may differ depending on the model.
43
Backlight / Contrast / Brightness /
Sharpness / Color / Tint (G/R)
MENU m → Picture → ENTER E
Picture
Picture Mode
· Backlight
· Contrast
· Brightness
· Sharpness
· Color
· Tint (G/R) G50
Information
55
100
45
50
50
R50
Your product has several options for adjusting picture quality.
Input source
PC , HDMI (when a PC is connected)
Picture Mode
Information , Advertisement
Adjustable options
Backlight / Contrast / Brightness /
Sharpness
AV , HDMI , TV Dynamic , Standard , Movie Backlight / Contrast / Brightness /
Sharpness / Color / Tint (G/R)
― When you make changes to Backlight , Contrast , Brightness , Sharpness , Color or Tint (G/R) , the OSD will be adjusted accordingly.
― You can adjust and store settings for each external device you have connected to an input on the product.
― Lowering picture brightness reduces power consumption.
The displayed image may differ depending on the model.
44
Picture Size
MENU m → Picture → Picture Size → ENTER E
Picture Size
Picture Size
· Position
Resolution Select
16:9
Off
The displayed image may differ depending on the model.
choose size and aspect ratio picture displayed on screen.
Picture Size
― Different Screen Adjustment options are displayed depending on the current input source.
• 16:9 : Sets the picture to 16:9 wide mode.
• Wide Zoom : Magnifies the picture size more than 4:3. A magnified picture can be moved up and down.
• Zoom : Magnifies the 16:9 wide pictures vertically to fit the screen size. A magnified picture can be moved up and down.
• Smart View 1 : Reduces the 16:9 picture by 50%.
― Smart View 1 is enabled only in HDMI mode.
• Smart View 2 : Reduces the 16:9 picture by 25%.
― Smart View 2 can be selected in HDMI mode or when you are watching DTV.
• Wide Fit : Enlarges the aspect ratio of the picture to fit the entire screen.
• 4:3 : Sets the picture to basic 4:3 mode.
― Do not set your product to 4:3 format for a long time.
The borders displayed on the left and right, or top and bottom of the screen may cause image retention (screen burn) which is not covered by the warranty.
• Screen Fit : Displays the full image without any cut-off when HDMI (720p / 1080i / 1080p) signals are inputted.
• Original Ratio : If the input source is PC or HDMI (PC connection) the video will display in the original aspect ratio.
• Custom : Changes the resolution to suit the user's preferences.
― Not available on analog TVs.
45
Picture Sizes available by Input Source.
Input Source
ATV
DTV (1080i)
AV (480i, 480p)
HDMI (720p, 1080i, 1080p)
HDMI (480i, 480p)
PC , HDMI (when a PC is connected)
Picture Size
16:9 , Wide Zoom , Zoom , 4:3
16:9 , Smart View 2 , Wide Fit , 4:3 , Screen Fit
16:9 , Wide Zoom , Zoom , 4:3 , Custom
16:9 , Smart View 1 , Smart View 2 , Wide Fit , 4:3 , Screen Fit ,
Custom
16:9 , Wide Zoom
Custom
, Zoom , Smart View 1 , Smart View 2 , 4:3 ,
16:9 , 4:3 , Original Ratio
46
Position
Picture Size
Picture Size
·
Position
Resolution Select
Wide Zoom
Off
The displayed image may differ depending on the model.
Zoom/Position
Picture Size
Picture Size
·
Zoom/Position
Resolution Select
Custom
Off
The displayed image may differ depending on the model.
Adjusts the picture position. Position is only available if Picture Size is set to Wide Zoom , Zoom , Wide Fit or Screen Fit .
― To use the Position function after selecting Wide Zoom , Zoom , Wide Fit or Screen Fit , follow these steps.
1
Press the button to select Position . Press the E button.
2
Press the or button to move the picture up or down.
3
Press the E button.
― If you want to reset the picture to its original position, select Reset in the Position screen.
― The picture will be set to its default position.
Adjusts the picture zoom and position. This option is available when the input source is set to HDMI (1080i/1080p) or AV
(1080i/1080p). Picture Size must be set to Custom for the option to be available.
1
Press the button to select Zoom/Position . Press the E button.
2
Select the Zoom or Position . Press the E button.
3
Press the / / / button to move the picture.
4 Press the E button.
― If you want to reset the picture to its original position, select Reset in the Zoom/Position screen.
― The picture will be set to its default position.
47
Resolution
If the picture is not normal even when the resolution of the graphics card is one of the following, you can optimize the picture quality by selecting the same resolution for the product as the PC using this menu.
Available resolutions: Off / 1024x768 / 1280x768 / 1360x768 / 1366x768
48
Auto Adjustment
MENU m → Picture → Auto Adjustment → ENTER E
Picture
Auto Adjustment
Available in PC mode only.
The displayed image may differ depending on the model.
PC Screen Adjustment
MENU m → Picture → PC Screen Adjustment → ENTER E
Picture
PC Screen Adjustment
Available in PC mode only.
The displayed image may differ depending on the model.
Adjust frequency values/positions and fine tune the settings automatically.
• Coarse / Fine
Removes or reduces picture noise.
If the noise is not removed by Fine-tuning alone, use the Coarse function to adjust the frequency as best as possible
( Coarse ) and Fine-tune again. After the noise has been reduced, re-adjust the picture so that it is aligned with the Center of screen.
• Position
To adjust the PC’s screen position if it is not Centered or does not fit the product screen.
Press the ▲ or ▼ button to adjust the Vertical Position. Press the ◄ or ► button to adjust the Horizontal Position.
• Image Reset
Resets the image to the default settings.
49
PIP
MENU m → Picture → PIP → ENTER E
Picture
PIP
The displayed image may differ depending on the model.
For PIP sound, refer to the Sound Select instructions.
If you turn the product off while watching in the PIP mode, PIP mode will remain after power
Off/On.
PIP Settings
The picture from the external video source will be in the main screen and the picture from the product will be in the PIP subpicture screen.
Main picture
AV , TV
Sub picture
PC , HDMI
HDMI PC , AV , TV
PC TV , AV , HDMI
• PIP ( Off / On ): Activate or deactivate the PIP function.
• Source : You can select a source of the sub picture.
• Antenna ( Air / Cable ): Select either Air or Cable as the input source for the sub-screen.
― This option is enabled if the secondary display is set to TV .
• Channel : Select the channel for the sub-screen.
― This option is enabled if the secondary display is set to TV .
• Size ( , , , , , ): Select a size for the subpicture.
• Position ( , , , ): Select a position for the sub-picture.
― In Double ( , , ) mode, you cannot select Position .
• Sound Select ( Main / Sub ): You can choose to listen to the sound from the Main picture or the Sub picture.
50
Advanced Settings
MENU m → Picture → Advanced Settings → ENTER E
Advanced Settings
Dynamic Contrast
Black Tone
Flesh Tone
RGB Only Mode
Color Space
White Balance
Gamma
Medium
Off
0
Off
Native
0
The displayed image may differ depending on the model.
Input Source
PC , HDMI (when a PC is connected)
TV , HDMI , AV
Picture Mode
Information ,
Advertisement
Dynamic
Standard
Movie
Advanced Settings
White Balance / Gamma
Not available.
Dynamic Contrast / Black Tone / Flesh Tone /
RGB Only Mode / Color Space / White Balance / Gamma
/ Motion Lighting
Dynamic Contrast / Black Tone / Flesh Tone /
RGB Only Mode / Color Space / White Balance / Gamma
51
Advanced Settings
Dynamic Contrast
Black Tone
Flesh Tone
RGB Only Mode
Color Space
White Balance
Gamma
Medium
Off
0
Off
Native
0
The displayed image may differ depending on the model.
Dynamic Contrast
Adjust the screen contrast.
• Off / Low / Medium / High
Black Tone
Select the black level to adjust the screen depth.
• Off / Dark / Darker / Darkest
Flesh Tone
Emphasize pink Flesh Tone .
RGB Only Mode
Displays the Red , Green and Blue color for making fine adjustments to the hue and saturation.
• Off / Red / Green / Blue
Color Space
Adjusts the range and variety of colors (the color space) available to create images.
• Auto / Native
52
Advanced Settings
White Balance
Gamma
Motion Lighting
The displayed image may differ depending on the model.
0
Off
White Balance
Adjust the color temperature for a more natural picture.
• R-Offset / G-Offset / B-Offset : Adjust each color’s (red, green, blue) darkness.
• R-Gain / G-Gain / B-Gain : Adjust each color’s (red, green, blue) brightness.
• Reset : Resets the White Balance to its default settings.
Gamma
Adjust the primary color intensity.
Motion Lighting
Reduces power consumption by reducing screen brightness when the picture on the screen is in motion.
• Off / On
53
Picture Options
MENU m → Picture → Picture Options → ENTER E
Picture Options
Color Tone
Color Temp.
Digital Clean View
MPEG Noise Filter
HDMI Black Level
Film Mode
Dynamic Backlight
Off
10000K
Off
Off
Normal
Off
Off
The displayed image may differ depending on the model.
Select an option using the and arrow keys, and the press E.
Use the arrow keys to change the setting, and then press E.
Input source Picture Mode Picture Options
PC , HDMI (when a PC is connected)
Information , Advertisement Color Tone / Color Temp.
/ HDMI Black Level /
Dynamic Backlight
HDMI Dynamic , Standard , Movie
TV , AV Dynamic , Standard , Movie
Color Tone / Color Temp.
/ Digital Clean View /
MPEG Noise Filter / Dynamic Backlight
Color Tone / Color Temp.
/ Digital Clean View /
MPEG Noise Filter / Film Mode / Dynamic Backlight
54
Picture Options
Color Tone
Color Temp.
Digital Clean View
MPEG Noise Filter
Off
10000K
Off
Off
The displayed image may differ depending on the model.
Color Tone
If the input source is PC , HDMI (PC connection).
• Off / Cool / Standard / Warm
If the input source is AV , HDMI or TV .
• Off / Cool / Standard / Warm1 / Warm2
― Warm1 or Warm2 will be deactivated when the Picture Mode is Dynamic .
― Settings can be adjusted and stored for each external device connected to an input on the product.
Color Temp.
Adjust the color temperature ( Red / Green / Blue ). (Range: 3000K–15000K)
― This option is available when Color Tone is set to Off .
Digital Clean View
If the broadcast signal received by your product is weak, you can activate the Digital Clean View feature to reduce any static and ghosting that may appear on the screen.
• Off / Low / Medium / High / Auto / Auto Visualization
― Auto Visualization : When changing analog channels, displays signal strength.
― When the signal is weak, try all the options until the the product displays the best picture.
MPEG Noise Filter
Reduces MPEG noise to provide improved picture quality.
• Off / Low / Medium / High / Auto
55
Picture Options
HDMI Black Level
Film Mode
Dynamic Backlight
Normal
Off
Off
The displayed image may differ depending on the model.
HDMI Black Level
Selects the black level on the screen to adjust the screen depth.
• Normal / Low
― Available only in HDMI (PC connection) mode (Enabled only when the color format is RGB.).
Film Mode
This mode is suitable to view movies.
Sets the product to automatically sense and process film signals from all sources and adjust the picture for optimum quality.
• Off / Auto1 / Auto2
― Available in TV , AV .
Dynamic Backlight
Automatically adjust the backlight to provide the best possible screen contrast under the current conditions.
• Off / On .
56
Picture Off
MENU m → Picture → Picture Off → ENTER E
Picture
Picture Off
The displayed image may differ depending on the model.
Reset Picture
MENU m → Picture → Reset Picture → ENTER E
Picture
Reset Picture
The displayed image may differ depending on the model.
Selecting Picture Off switches off the screen. The volume is not disabled.
To switch the screen on, press any button other than the volume button.
Resets your current picture mode to its default settings.
57
Chapter 06
Sound Adjustment
Configure the sound ( Sound ) settings for the product.
Sound Mode
MENU m → Sound → Sound Mode → ENTER E
Sound
Sound Mode
Sound Effect
Speaker Settings
Additional Settings
Reset Sound
Standard
The displayed image may differ depending on the model.
You can select a sound mode to suit your personal preferences.
• Standard : Selects the normal sound mode.
• Music : Emphasizes music over voices.
• Movie : Provides the best sound for movies.
• Clear Voice : Emphasizes voices over other sounds.
• Amplify : Increase the intensity of high-frequency sound to allow a better listening experience for the hearing impaired.
58
Sound Effect
MENU m → Sound → Sound Effect → ENTER E
Sound
Sound Effect
The displayed image may differ depending on the model.
Configure your preferred sound effect for output sound.
― Available only when Sound Mode is set to Standard .
• DTS TruSurround HD ( Off / On )
This function provides a virtual 5.1 channel surround sound experience through a pair of speakers using HRTF(Head
Related Transfer Function) technology.
• DTS TruDialog ( Off / On )
This function allows you to increase the intensity of a voice over background music or sound effects so that dialog can be heard more clearly.
• Equalizer
Use Equalizer to customize sound setting for each speaker.
Balance L/R : Adjusts the balance between the right and left speaker.
100Hz / 300Hz / 1kHz / 3kHz / 10kHz (Bandwidth Adjustment): Adjusts the level of specific bandwidth frequencies.
Reset : Resets the equalizer to its default settings.
59
Speaker Settings
MENU m → Sound → Speaker Settings → ENTER E
Sound
Speaker Settings
The displayed image may differ depending on the model.
• Auto Volume ( Off / Normal / Night )
The volume can vary depending on the channel.
Automatically equalize the volume level when switching to another channel.
Normal equalizes the volume level on each channel, so that when you change channels, the volume level is the same.
Night equalizes and decrease the volume level on each channel, so each channel is quieter. Night is useful at night, when you may want to keep the volume low.
― To use the volume control of a connected source device, set Auto Volume to Off . A change to the volume control of the connected source device may not be applied if Auto Volume is set to Normal or Night .
60
Additional Settings
MENU m → Sound → Additional Settings → ENTER E
Sound
Additional Settings
The displayed image may differ depending on the model.
DTV Audio Level
(Digital channels only)
The TV cannot freely control the volume of the digital audio that it sends to the AV receiver. Use this to set the digital audio volume at a comfortable level.
― According to the type of broadcast signal, MPEG / HE-AAC can be adjusted between -10dB and 0dB.
― To increase or decrease the volume, adjust between the range 0 and -10 respectively.
Dolby Digital Comp
Some digital TV programmes provide 5.1-channel Dolby audio. This TV converts Dolby audio to stereo audio so that it can play the sound through the TV’s speakers. There are two methods to choose from. RF is for better sound at lower volumes, and Line is for higher volumes.
61
Reset Sound
MENU m → Sound → Reset Sound → ENTER E
Sound
Reset Sound
The displayed image may differ depending on the model.
Reset all sound settings to the factory defaults.
62
Chapter 07
Broadcasting
Configure the Broadcasting settings for the product.
Auto Tuning
MENU m → Broadcasting → Auto Tuning → ENTER E
Broadcasting
Auto Tuning
Antenna
Channel List
Guide
Schedule Manager
Edit Channel
Edit Favorites
Air
The displayed image may differ depending on the model.
Available in TV mode only.
The Auto Tuning function memorizes all channels that are available over the air or through your cable system and adds them to the Channel List .
To start Auto Tuning , follow these steps:
1
Push MENU m → Broadcasting → Auto Tuning → ENTER E on your remote. The Auto Tuning screen appears.
2
On the Auto Program screen, select the source of your product signal.
― Air : If your product is connected to an antenna choose Air , and then press ENTER E. The product will automatically start memorizing channels.
― Cable : If your product is connected to a cable outlet, choose Cable , and then press ENTER E. Go to Step 3.
3
On the cable type screen, use the / buttons to select the type of digital and analog cable systems you have: STD,
HRC, or IRC. Most systems are STD (Standard). When done, select Next , and then press ENTER E. The product will start memorizing channels.
― Channel memorization can take up to 45 minutes, depending on your cable system.
― Memorized channels are added to the Added Ch.
list. These are the channels you will see when you use the channel buttons on your remote.
Cancelling Auto Tuning
1
Press the Stop button.
2
A Stop Auto Tuning?
message appears.
3
Press the Yes button.
63
Antenna
MENU m → Broadcasting → Antenna → ENTER E
Broadcasting
Antenna Cable
The displayed image may differ depending on the model.
Available in TV mode only.
Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the LED display.
• Air / Cable
64
Channel List
MENU m → Broadcasting → Channel List → ENTER E
Broadcasting
Channel List
The displayed image may differ depending on the model.
Available in TV mode only.
Register or delete channels. Add favorite channels or rename analog channels.
Select a desired channel from Channel List to view the channel instantly.
― To navigate Channel List faster, press the channel buttons. The channel list changes page by page.
Icons found in the channel list page
•
•
•
A : Analog channel
* : A channel that is selected
\ : Locked channels
Pressing the right cursor ( ) button on the remote control displays the Mode page.
Mode
Antenna
Select either Air or Cable as digital channel mode.
Edit Favorites
Edit favorite channel lists from Edit Favorites .
Favorites 1 ~ Favorites 5
Shows all favorite channels, in up to five groups. Each group has a separate screen.
― The TV displays favorite groups only if you have added favorites using Favorites 1 - to Favorites 5 .
All
Shows all channels.
TV
Shows channels.
Analog
Shows Analog channels.
65
Guide
MENU m → Broadcasting → Guide → ENTER E
Broadcasting
Guide
The displayed image may differ depending on the model.
Available in TV mode only.
The Guide provides an overview of each digital channel's program lineup. You can check the program schedules and set up a
Schedule Manager .
― The information in the Guide is for digital channels only. Analog channels are not supported.
You can press the color keys on the remote to access optional functions.
Quick Nav
Search channel information quickly.
Schedule Manager
Access the Schedule Manager function.
You can view information on the Schedule Manager .
Channel Category
The Channel List varies depending on the selected option.
66
Schedule Manager
MENU m → Broadcasting → Schedule Manager → ENTER E
Broadcasting
Schedule Manager
The displayed image may differ depending on the model.
Available in TV mode only.
Watch a desired channel at a scheduled time.
• Antenna : DTV Cable / Cable / DTV Air / Air
• Channel : Select the desired channel.
• Repeat : Once / Manual / Sat~Sun / Mon~Fri / Everyday
― Select Manual if you want to configure settings by day of the week.
• Date : Select the desired date.
• Start Time : Set the time to watch the desired channel.
67
Edit Channel
MENU m → Broadcasting → Edit Channel → ENTER E
Broadcasting
Edit Channel
The displayed image may differ depending on the model.
Available in TV mode only.
Manage channels saved on your TV. Delete channels, re-register deleted channels or rename analog channels.
― Conveniently configure settings using the remote control buttons displayed at the bottom of the screen.
Icons found in the edit channel page
•
•
•
A : Analog channel
* : A channel that is selected
\ : Locked channels
Deleting/registering channels
Deleting channels
Delete channels, if required. Note that deleting channels from the Recently Viewed or Mostly Viewed category does not remove the channels permanently. The channels are only removed from the categories.
1
Select channels to delete from the screen. To cancel, select again.
2
After selecting channels, select Delete from the screen to delete the channels.
Re-registering deleted channels
Register deleted channels again, if required. Deleted channels are grayed out and can only be found in the list of all channels.
The register function is enabled for deleted channels only.
1
Press TOOLS on the screen to display the Tools page. Select Category from the sub-menu items and then select All .
2
From the list of all channels, select deleted channels you want to register again.
3
After selecting channels, select Add from the screen to re-register the channels.
68
Editing registered channels
Pressing TOOLS from the Edit Channel page displays the following menu items. Provided functions may vary depending on the broadcast signal.
Option Name Operations
Sorting Select either Air or Cable as digital channel mode.
Category Channels saved on your TV are classified under the All , TV , Analog , Recently
Viewed and Mostly Viewed categories. Select a desired category.
Edit Favorites
Rename Channel
Channel Info
Information
Set frequently viewed channels as favorite channels.
Change the names of analog channels to suit your preferences. A channel name can be up to five characters long.
Check the information of the channel.
View information about the current broadcast program on the air.
Locking/unlocking channels using a password
Lock specific channels to prevent children from accessing inappropriate content.
― To set a password, make sure Channel Lock is set to On .
Locking channels
1
Select a channel from the Edit Channel page, and then select Channel Lock from the screen. The password input window is displayed.
2
Enter the password. The selected channel is locked.
Unlocking channels
1
Select a locked channel from the Edit Channel page, and then select Channel Lock Off from the screen. The password input window is displayed.
2
Enter the password. The selected channel is unlocked.
69
Edit Favorites
MENU m → Broadcasting → Edit Favorites → ENTER E
Broadcasting
Edit Favorites
The displayed image may differ depending on the model.
Available in TV mode only.
Creating a favorite channel list
Set frequently viewed channels as favorite channels. Favorite channels are indicated by a symbol in the Edit Channel or
Channel List page. A maximum of five favorite channel lists are allowed. Create different favorite channel lists for each family member.
― Conveniently configure settings using the remote control buttons displayed at the bottom of the screen.
Adding the current channel to a favorite channel list
Add the channel you are currently watching to a favorite channel list.
1 When watching TV, press TOOLS to display the Tools page. Select Edit Favorites from the sub-menu items.
2 From the displayed prompt box, select a favorite channel list to save the current channel to. Select OK .
3 The current channel is added in the selected favorite channel list. Select OK .
Adding multiple channels to a favorite channel list
Add multiple channels to a favorite channel list, if required.
1
Select Category from the screen to change the channel list in the center of the screen to the channel list that contains the channels to add. Each time Category is selected, the category switches in the order Recently Viewed , Mostly
Viewed , and All , TV , Analog .
― Recently Viewed and Mostly Viewed are only enabled if they contain saved channels.
2
Select desired channels from the channel list in the center of the screen.
3
Select Change Fav.
from the screen to change the favorite channel list on the right to another desired favorite channel list.
4
Select Add from the screen. The selected channels will create a favorite channel list.
70
Viewing channels saved under a favorite channel list
― Favorite channel lists are only displayed if they have been created previously.
When changing the channel using the channel buttons, channels saved in favorite channel lists can only be accessed.
1
Select Channel List from the Channel menu. The channel list is displayed.
2
Pressing the right cursor ( ) button on the remote control displays the Mode page.
3
Select a favorite channel list among Favorites 1 – Favorites 5 .
4
Select channels from the selected favorite channel list.
― Selecting Channel List while watching a favorite channel will display the updated favorite channel list.
Editing favorite channel lists
Pressing TOOLS from one of the Favorites 1 - to Favorites 5 pages displays the following menu items.
Option Name Operations
Copy to Favorites Copy channels from a favorite channel list to another favorite channel list.
― This option is only available when channels under a favorite channel list are selected.
Rename Favorites Change the name of a favorite channel list.
― This option is only available when channels under a favorite channel list are selected.
Antenna Select either the Air or Cable signal.
Edit Channel
Information
Manage saved channels.
View information about the current broadcast program on the air.
Deleting channels from a favorite channel list
Delete channels from a favorite channel list, if required.
1
Select Change Fav.
from the screen to change the favorite channel list on the right to another desired favorite channel list.
2
Select channels to delete from the selected favorite channel list.
3
Select Delete from the screen. The selected channels are deleted from the favorite channel list.
Changing the order of channels in a favorite channel list
Change the order of channels saved in a favorite channel list, if required.
1 Select Change Fav.
from the screen to change the favorite channel list on the right to another desired favorite channel list.
2 Select channels to rearrange from the selected favorite channel list.
3 Select Change order from the screen, and then change the order of the selected channels. To apply the new order of the channels, press the E button.
71
Renaming a favorite channel list
Change the name of a favorite channel list, if required.
1
Select Change Fav.
from the screen to change the favorite channel list on the right to another desired favorite channel list.
2
Press TOOLS on the screen. Sub-menu items are displayed.
3
Select Rename Favorites from the sub-menu items. A prompt box appears.
4
Change the favorite channel list using the prompt box. The name for a favorite channel list can be up to 20 characters long.
Copying channels between favorite channel lists
Copy channels from a favorite channel list to another favorite channel list, if required.
1 Select Change Fav.
from the screen to change the favorite channel list on the right to another desired favorite channel list.
2 Select channels to copy from the favorite channel list on the right.
3 Press TOOLS on the screen. Sub-menu items are displayed.
4 Select Copy to Favorites from the sub-menu items. A prompt box appears.
5 Select favorite channel lists to copy the channels to using the prompt box. The channels are saved to the selected favorite channel lists.
― To use Copy to Favorites , make sure channels are saved in a favorite channel list.
72
Channel Settings
MENU m → Broadcasting → Channel Settings → ENTER E
Broadcasting
Channel Settings
The displayed image may differ depending on the model.
Available in TV mode only.
Digital Manual Tuning
Scans for a channel manually and stores in the TV .
If a channel is locked using the Channel Lock function, the PIN input window appears.
This function depends on the country and region.
Fine Tune
(analog channels only)
If the reception is clear, you do not have to fine tune the channel, as this is done automatically during the search and store operation. If the signal is weak or distorted, fine tune the channel manually. Scroll to the left or right until the image is clear.
― This function is only available for analog channels.
― Settings are applied to the channel you’re currently watching.
― Fine tuned channels that have been saved are marked with an asterisk “*” on the right-hand side of the channel number in the channel banner.
― To reset the fine-tuning, select Reset .
Color System
Change the Color System according to the broadcast signal.
• Auto / PAL-M / PAL-N / NTSC
73
Subtitle
MENU m → Broadcasting → Subtitle → ENTER E
Subtitle
Subtitle
Primary Subtitle
Secondary Subtitle
The displayed image may differ depending on the model.
Available in TV mode only.
Configures the subtitle options.
Subtitle
(digital channels only)
Show subtitles.
• Subtitle Mode : Set the subtitle mode.
• Subtitle Language : Set the subtitle language.
Primary Subtitle
Set the primary subtitle language.
Secondary Subtitle
Set the secondary subtitle language.
74
Caption
MENU m → Broadcasting → Caption → ENTER E
Broadcasting
Caption
The displayed image may differ depending on the model.
Available in TV mode only.
Caption
(analog channels only)
You can switch the caption function on or off.
If captions are not available, they will not be displayed on the screen.
• Off / On
― The Caption feature does not work with devices connected to the product through the HDMI input jacks.
Caption Mode
You can select the caption mode to use.
― The caption feature is available depending on the content being broadcast.
• Default / CC1 ~ CC4 / Text1 ~ Text4 (in analog channels only) : Select the caption mode to use on analog channels.
(Except for Default , some caption modes may not be available depending on the broadcasting signal.)
• Default / Service1 ~ Service6 / CC1 ~ CC4 / Text1 ~ Text4 (in digital channels only) : Select the caption mode to use on digital channels.
(Except for Default , some caption modes may not be available depending on the broadcasting signal.)
― If you are not sure about which caption mode is available for a channel, set the Caption Mode to Default .
75
Digital Caption Options
You can customize Caption settings when the Caption Mode is set to one of Service1 to Service6 .
(digital channels only)
Configure the subtitle settings such as size and color.
Adjusts the each option. When done, select Close .
• Size : Options include Default , Small , Standard and Large . The default is Standard .
• Font Style : Select the caption fonts.
• Font Color : You can change the color of the letters. Options include Default , White , Black , Red , Green , Blue , Yellow ,
Magenta and Cyan . The default is White .
• Background Color : You can change the background color of the caption. Options include Default , White , Black , Red ,
Green , Blue , Yellow , Magenta and Cyan . The default is Black .
• Font Opacity : This adjusts the opacity of text. Options include Default , Transparent , Translucent , Solid and Flashing .
• Background Opacity : This adjusts the opacity of the caption background. Options include Default , Transparent ,
Translucent , Solid and Flashing .
• Return to Default : This option sets each Size , Font Color , Background Color , Font Opacity and Background Opacity to their default.
― Digital Caption Options are available only when you can select Return to Default and Service1 ~ Service6 in
Caption mode.
― The availability of captions depends on the program being Broadcasted.
― The Return to Default setting follows the standards set by the broadcaster.
― You cannot set the Font Color and Background Color to the same color.
― You cannot set both the Font Opacity and the Background Opacity to the same color.
76
Audio Options
MENU m → Broadcasting → Audio Options → ENTER E
Audio Options
Multi-Track Sound
Audio Language
Audio Format
Mono
English
The displayed image may differ depending on the model.
Available in TV mode only.
Multi-Track Sound
Select an option using the up and down arrow keys, and the press E.
• Mono : Choose for channels that are Broadcasting in mono or if you are having difficulty receiving a stereo signal.
• Stereo : Choose for channels that are Broadcasting in stereo.
• SAP : Choose to listen to the Separate Audio Program, which is usually a foreign-language translation.
― Depending on the program being broadcast, you can listen to Mono , Stereo or SAP .
Audio Language
(for digital broadcasts)
Change the default value for audio languages.
Select the type of audio languages in the current channel.
• Audio Language / Primary Audio / Secondary Audio
― The available language may differ depending on the broadcast.
Audio Format
(for digital broadcasts)
Change a desired audio format. The supported audio format may vary depending on the broadcast program.
77
Channel Lock
MENU m → Broadcasting → Channel Lock → ENTER E
Broadcasting
Channel Lock On
The displayed image may differ depending on the model.
Available in TV mode only.
Prevent your children from accessing harmful content by locking channels.
• On / Off
― This option is available when the input source is TV .
― The default PIN number for a new product set is “0-0-0-0”.
― Availability depends on the specific model and area.
78
Chapter 08
Network
Network Status
MENU m → Network → Network Status → ENTER E
You can check the current network status.
Network Status
Your wireless network is setup and ready to use.
MAC Address
IP Address
Subnet Mask
Gateway
** : ** : ** : ** : ** : **
***.
***.
***.
***.
***.
***.
***.
***.
***.
***.
***.
***.
AP0000
Ready to play your business content.
-Run the Content Creator on your PC, then create and schedule your content. You can send it to the Signage TV using the wireless network.
-Refer to the Content Creator manual for more information.
Disconnect IP Settings Retry Close
The displayed image may differ depending on the model.
Network Settings
MENU m → Network → Network Settings → ENTER E
Connect to a wireless network and use the product as a TV+signage using MagicInfo Express Content
Creator on your PC.
Network Settings
Your wireless network is setup and ready to use.
WPS(PBC)
AP000
Ready to play your business content.
-Run the Content Creator on your PC, then create and schedule your content. You can send it to the Signage TV using the wireless network.
-Refer to the Content Creator manual for more information.
The displayed image may differ depending on the model.
79
Network Setting (Wireless)
Connecting to a Wireless Network
Samsung recommends using IEEE 802.11n. When you play video over a network connection, the video may not play smoothly.
― Select a channel for the wireless IP sharer that is not currently being used. If the channel set for the wireless IP sharer is currently being used by another device nearby, this will result in interference and communication failure.
― Your product supports only the following wireless network security protocols.
If you select the Pure High-throughput (Greenfield) 802.11n mode and the Encryption type is set to
WEP, TKIP or TKIP AES (WPS2Mixed) on your AP or wireless router, Samsung products will not support a connection in compliance with new Wi-Fi certification specifications.
― If your wireless router supports WPS (Wi-Fi Protected Setup), you can connect to the network via PBC
(Push Button Configuration) or PIN (Personal Identification Number). WPS will automatically configure the SSID and WPA key in either mode.
― Connection Methods: You can setup the wireless network connection in three ways.
Auto Setup (Using the Auto Network Search function), Manual Setup, WPS(PBC)
Automatic Network Setup (Wireless)
Most wireless networks have an optional security system that requires devices that access the network to transmit an encrypted security code called an Access or Connection Information . The Connection
Information is based on a Pass Phrase, typically a word or a series of letters and numbers of a specified length you were asked to enter when you set up security for your wireless network. If you use this method of setting up the network connection, and have a Connection Information for your wireless network, you will have to enter the Pass Phrase during the the automatic or manual setup process.
How to set up automatically
1
Go to MENU m → Network → Network Settings .
2
The Network function searches for available wireless networks. When done, it displays a list of the available networks.
3
In the list of networks, press the ▲ or ▼ button to select a network, and then press the E button.
― If the desired wireless router does not appear, select Refresh to search again.
― If the router cannot be found after retrying, select the Stop button.
The Add Network button appears.
Select Add Network to add a wireless router to connect to.
4 If the Enter password.
screen appears, go to step 5. If you select a wireless router that does not have security, go to step 7.
5 If the router has security, enter the Enter password.
(Security key or PIN).
80
6
When done, use the down arrow button to move the cursor to Done , and then press E. The network connection screen appears and the verification process starts.
― This product cannot connect to the Internet via Soft AP (Wi-Fi Hotspot) or Wi-Fi Direct .
7 When the connection has been verified, the “ Your wireless network is setup and ready to use.
” message appears.
Manual Network Setup (Wireless)
Offices may use static IP addresses.
If this is the case, ask the network administrator for the IP address, subnet mask and gateway. Enter these values manually.
Getting the Network Connection Values
To view the Network connection values on most Windows computers, follow these steps.
1
Right click the Network icon on the bottom right of the screen.
2
In the pop-up menu that appears, click Status.
3
On the dialog that appears, click the Support tab.
4
On the Support Tab, click the Details button. The Network connection values are displayed.
How to set up manually
On the product, go to MENU m → Network → Device Name and change the product's device name.
― If you are using multiple products, make sure to change their device names.
1 Go to MENU m → Network → Network Settings .
2 The Network function searches for available wireless networks. When done, it displays a list of the available networks.
3 In the list of networks, press the u or d button to select a network, and then press the E button twice.
― If the desired wireless router does not appear, select Refresh to search again.
― If the router cannot be found after retrying, select the Stop button.
The Add Network button appears.
Select Add Network to add a wireless router to connect to.
4
If the Enter password.
screen appears, go to step 5. If you select a wireless router that does not have security, go to step 7.
5
If the router has security, enter the Enter password.
(Security key or PIN).
6
When done, use the right arrow button to move the cursor to Done , and then press E. The network connection screen appears and the verification process starts.
7
Select Stop while network connections are being attempted. This will stop the connection.
8
Select IP Settings on network connection screen. The IP Settings screen appears.
9
Select the field at the top, press E, and then set IP Settings to Enter manually . Repeat the entry process for each field in the IP Address .
81
10
When done, select OK at the bottom of the page, and then press E. The network test screen appears and the verification process starts.
11
When the connection has been verified, the “ Your wireless network is setup and ready to use.
” message appears.
WPS(PBC)
How to set up using WPS(PBC)
If your router has a WPS(PBC) button, follow these steps.
1
Go to MENU m → Network → Network Settings .
2
Select WPS(PBC) , press E, and then press E again.
3
Press the WPS(PBC) button on your router within 2 minutes. Your product automatically acquires all the network setting values it needs and connects to your network.
4
The network connection screen appears, and network setup is done.
82
Soft AP (Wi-Fi Hotspot)
MENU m → Network → Soft AP (Wi-Fi Hotspot) → ENTER E
Using this function, you can connect the product on your mobile devices if your mobile devices do not support Wi-Fi Direct .
Set the options for connection of Wi-Fi device.
• Soft AP (Wi-Fi Hotspot)
Turns on or off the Soft AP (Wi-Fi Hotspot) . When Soft AP (Wi-Fi Hotspot) is set to On , your mobile devices can find the product name in Wi-Fi connection list.
• Connection Information
Displays the TV name (SSID) and password.
• Reset password
Powering on the display creates a new security key and disconnect any existing Soft AP (Wi-Fi Hotspot) connection.
Off / On
• Advanced Settings
Change detailed Wi-Fi settings.
Channel ( CH.1
~ CH.11
)
Change Wi-Fi channel settings.
Signal Level ( Level 1 ~ Level 5 )
Change Wi-Fi signal level settings.
83
To use this function, your mobile device should be supported by the Wi-Fi Direct .
Wi-Fi Direct
MENU m → Network → Wi-Fi Direct → ENTER E
Set to connect the product to wireless mobile devices. Using this function, you can connect wireless mobile devices with your product directly without a router.
To connect your mobile device with your product using Wi-Fi Direct, follow these steps:
1 Go to Wi-Fi Direct screen. The product starts to search devices.
2 Turn on the Wi-Fi Direct function on your device. Select the desired Wi-Fi device.
• PBC (Push Button Configuration): Press the WPS(PBC) button on your Wi-Fi device within 2 minutes. Your product automatically acquires all the network setting values it needs and connects to your network.
• PIN : Input the displayed PIN on your device.
― If you want to disconnect the device, select the connected Wi-Fi device, and then select Disconnected .
84
AllShare Settings
MENU m → Network → AllShare Settings → ENTER E
Shows a list of mobile phones or connected devices which have been set up to use the AllShare Play function with this product.
• Allow / Deny : Allows/Blocks the devices.
• Delete from the list : Deletes the devices from the list.
― This function only deletes the name of the device from the list. If the deleted device is turned on or tries to connect to the product, it may appear on the list again.
Using the AllShare Play Function
An alarm window appears informing you that media contents (videos, photos, music) sent from a mobile phone will be displayed on your product. The contents are played automatically 3 seconds after the alarm window appears. If you press the RETURN or EXIT button when the alarm window appears, the media contents are not played.
― The first time a device accesses your product through the media function, a warning popup window appears. Press the E button to select Allow . This permits the phone to access the product freely and use the AllShare Play function to play content.
― To turn off media contents transmissions from a mobile phone, set Deny in the AllShare Settings .
― Contents may not play on your product depending on their resolution and format.
― The E and ◄ / ► buttons may not work depending on the type of media content.
― Using the mobile device, you can control the AllShare Play . For details, refer to each mobile’s user’s guide.
Device Name
MENU m → Network → Device Name → ENTER E
Select or enter a device name.
This name can be shown on network remote controls over the network.
85
Chapter 09
Applications
Source List
MENU m → Applications → Source List → ENTER E
Source
TV HDMI AV PC USB
The displayed image may differ depending on the model.
Source allows you to select a variety of sources and change source device names.
You can display the screen of a source device connected to the product. Select a source from source list to display the screen of the selected source.
― The input source can also be changed by using the SOURCE button on the remote control.
― The screen may not display correctly if an incorrect source is selected for the source device you want to convert to.
― To view detailed information about connected source devices, press the TOOLS button from the Source page.
― If the product is in portrait orientation, it is not possible to change Source List .
Edit Name
SOURCE → Source → TOOLS → Edit Name → ENTER E
Sometimes the screen will not display properly unless the name of a source device is specified in Edit Name .
In addition, it is best to rename the source device in Edit Name to obtain optimal picture quality.
― The list can include the following source devices. Source devices on the list differ depending on the selected source.
PC / Cable STB / Satellite STB / PVR STB / Game / Blu-ray / DVD / VCR / AV Receiver / Camcorder / DVI PC /
DVI Devices / TV / IPTV / HD DVD / DMA
― Available settings in the Picture menu depend on the current source and settings made in Edit Name .
Information
SOURCE → Source → TOOLS → Information → ENTER E
You can see detailed information about the selected external device.
86
MagicInfo
MENU m → Applications → MagicInfo → ENTER E
Applications
MagicInfo
Press HOME or MagicInfo Player I on the remote control to access the application more quickly.
The displayed image may differ depending on the model.
MagicInfo is a business solution that allows the product to be used as a signage (advertising media). Using the solution, play image and video files from the internal memory or a connected USB storage device. You can also play schedules created using the MagicInfo Express Content Creator on your computer.
Playing content from the internal memory or USB
Play content from the internal memory or a connected USB storage device.
Playing PC or mobile content
Send content via the MagicInfo Express Content Creator or a mobile app to the product for playback. If the internal memory is insufficient, connect a USB device and go to Options → Settings → Default Storage at the top right of the MagicInfo browser. Change the option to USB .
87
Schedule
Device : All Content : All Sort by : File Name Options
The displayed image may differ depending on the model.
Schedule
Play configured schedules.
Available features in the MagicInfo page
The MagicInfo list page provides the following features.
• Device
Select either Internal or USB to search for a desired device list.
All / Internal / USB
• Content
Select a content type as criterion to search for a desired content list.
All / My Templates / Video / Image
• Sort by
Specify the content sort criterion.
File Name / Recently Played
• Options
Options menu items in the MagicInfo screen
Option Name
Play Selected
Operations
Select and play desired content.
Send
Delete
Settings
Copy content to another storage device.
Delete desired content.
Configure detailed properties of content.
― See the following page for details on the Settings feature.
88
Settings
Settings
Select the storage location that you want to download scheduled channels from the network to.
Default Storage
Repeat Mode
Picture Size
Display Duration
Safely Remove USB
Reset Settings
Internal
One Close
The displayed image may differ depending on the model.
Default Storage
Select the storage location that you want to download scheduled channels from the network to.
• Internal / USB
Repeat Mode
Set repeat mode whether to repeat playing contents or not.
• One / All
Picture Size
Set Picture Size to either Screen Fit or Original Size .
• Screen Fit / Original Size
― Available only for Video and Image content.
Display Duration
Set the duration for each page in a slideshow.
― Available only for Template and Image content.
Safely Remove USB
Safely removes USB memory
Reset Settings
Restore all the values under Settings to the default when the product was purchased.
89
Chapter 10
MagicInfo Express Content Creator
For more information, refer to the user guide for the MagicInfo Express Content Creator tool from the website.
Installation requirements
HDD: At least 500 MB of free space
Operating system: Windows XP or later
Resolution: 1024x768 or higher
Using MagicInfo Express Content Creator
MagicInfo Express Content Creator is a program that allows you to conveniently create content using a variety of templates. Using MagicInfo Express Content Creator, create and manage schedules to play content on the product at a specific time.
― To use the MagicInfo Express Content Creator tool, download the tool from http://www.samsung.com/displaysolutions.
• Create Content : Create and manage templates that will be played on Samsung display devices.
• Schedule Content : Create and manage schedules to play content at specified times.
Managing templates
Using the templates provided in the program, organize a variety of content items based on predefined layouts to conveniently create new templates. Import and edit previously created templates.
Managing schedules
Configure and manage schedules to play content on Samsung display devices at specific times. Set the same schedule to play on specified days of the week or set different schedules to play by day of the week.
90
Chapter 11
Playing photos, videos and music (Media Play)
Enjoy videos, photos, music files saved on a USB Mass Storage Class (MSC) device.
Play photos, videos or music saved on a storage device.
Play a variety of content using the following methods.
• Using a USB device: Play media content such as videos, photos and music from a USB device.
• Connecting a storage device: Play media content saved on a storage device such as a smartphone, camera, PC or cloud service.
Read the following before using media play with a USB device
Caution
• Before connecting a USB device to the product, back up files to ensure your data is not damaged or lost.
Samsung Electronics is not liable for any damage or loss of data.
• Do not remove a USB device while it is loading.
• If a USB device is connected using a USB extension cable, the USB device may not be recognized or files saved on the device may not be able to be read.
• If the product does not recognize a connected USB device, the files on the USB device may be corrupted or may not be able to be played.
If this occurs, connect the USB device to the PC to format the device, then make sure the device is connected properly.
• USB HDD greater than 2TB is not supported.
91
Compatible devices with media play
• Some USB digital cameras, smartphones and audio devices may not be compatible with the product.
• Media play is only compatible with USB MSC devices.
• MSC device refers to a Mass Storage Class Bulk-Only Transport device.
Examples of MSC devices include Thumb drives, Flash card readers and USB HDDs. (USB hubs are not supported.)
These MSC devices must be connected directly to a USB port on the product.
• If more than one Picture Transfer Protocol (PTP) device is connected, only one will work at a time.
• If multiple MSC devices are connected, some devices may not be recognized. USB devices that require high power (higher than 500mA or 5V) may not be supported.
• If an overheating warning message appears when a USB device is connected or used, the USB device may not be recognized or function properly.
• The screensaver activates if the product is left idle for a period of time specified in Auto Protection Time .
• Power-saving mode on some external hard disk drives may automatically deactivate after connecting to the product.
File system and formats
• Media play may not function properly with unlicensed multimedia files.
• Media Transfer Protocol (MTP) is not supported.
• Supported file systems include FAT16, FAT32 and NTFS (read only).
• Media play supports the sequential JPEG format.
It does not support the progressive JPEG format.
• Images with a higher resolution take longer to be displayed on the screen.
• The maximum JPEG resolution supported is 15360x8640 pixels.
• If a file is incompatible or corrupted, a message Not Supported File Format.
appears.
• When sorting files in folder view mode, a maximum of 1000 files can be displayed in each folder.
• If a USB device contains 8000 files and folders or more, some files and folders may not open.
• DRM MP3 files downloaded from websites that charge a fee cannot be played.
― Digital Rights Management (DRM) refers to a system for protecting the copyrights of data circulated via the Internet or other digital media by enabling secure distribution and/or disabling illegal distribution of the data.
92
It is recommended to use a USB HDD that has a power adapter.
It is recommended to remove a USB device using the Remove USB function.
Using a USB device
Connecting a USB device
1
Turn on your product.
2
Connect a USB device containing photo, music and/or movie files to the USB port on the back or side panel of the product.
3
The USB device connected.
page automatically appears as soon as a USB device connects to the product.
― If only one USB device is connected, files saved on the USB device are displayed automatically.
― To view content saved on a USB device, connect the USB device to a USB port on the product.
― Connecting a USB device automatically runs MagicInfo. To run Media Play, connect a USB device, close MagicInfo, and then select USB from Source List .
Removing a USB device
Removing a USB device from Source
1 Press SOURCE on the remote control. Alternatively, go to Source using the OSD menu.
SOURCE → Source
2
Select USB from Source , and then press the TOOLS button on the remote control. Optional menu items are displayed.
3
Select Remove USB and wait until the USB device is disconnected. The USB device is disconnected.
93
Menu items in the media content list page
Option Name
Slide Show
Encoding
Play Selected
Operations
Start a slideshow.
― This menu item is not available if Sort by is set to Folder .
Select an encoding language if the title of media content appears corrupted.
Select and play desired content from the media content list.
Photos
c
Videos Music
c c c c
94
Pressing the INFO button while a file is selected will display information about the selected file.
Available buttons and features during photo playback
Pressing the E or TOOLS button displays the following buttons. The RETURN button makes the buttons disappear.
• Previous / Next
View the previous or next photo.
• Start Slide Show / Stop Slide Show
Start or stop a slideshow. Using a slideshow, it is possible to play all photos in a folder.
• Slideshow Settings
Speed : Change the slideshow speed.
Effects : Apply transition effects between photos.
• Zoom
Zoom in on photos up to 4x.
• Rotate
Rotate photos.
• Background Music
Play background music while viewing photos.
Background Music / Mini Player
― Make sure a music file is saved on the same device.
― Pause the current music playing or switch to another music file using Mini Player .
• Settings
Option Name
Picture Mode
Sound Mode
Information
Operations
Change the Picture Mode .
Change the Sound Mode .
― This menu item is only available when Background Music is playing.
View information about a file.
95
Available buttons and features during video playback
Pressing the E or TOOLS button displays the following buttons. The RETURN button makes the buttons disappear.
• Pause / Play
Pause or play a video.
The following features are available in pause mode. Note that sound cannot be heard in pause mode.
• Rewind / Fast forward
Rewind or fast forward a video. Speed up playback up to 3x, if required. To change the playback speed to the original speed, select ∂.
• Previous / Next
To play the previous video, select twice. Selecting once will play the current video from the beginning.
To play the next video, select ‚.
• Search
Select and play another video in the same folder. ( Search Titles )
• Repeat mode
Configure Repeat mode .
( Off , Repeat One , Repeat All )
• Picture Size
Change the screen size ( Picture Size ). Supported screen sizes vary depending on the image. ( Original / Mode1 / Mode2 / Smart View 1 /
Smart View 2 )
• Settings
Option Name Operations
Picture Mode Change the Picture Mode .
Sound Mode
Audio Language
Information
Change the Sound Mode .
Play a video using a desired language. This feature only activates when a streaming file that supports multiple audio formats is playing.
View information about a file.
96
Available buttons and features during music playback
Pressing the E or TOOLS button displays the following buttons. The RETURN button makes the buttons disappear.
• Pause / Play
Pause or play music.
• Rewind / Fast forward
Rewind or fast forward music. Speed up playback up to 3x, if required. To play the previous music file, select ∂ twice.
• Previous / Next
To play the previous music file, select twice. Selecting once will play the current music from the beginning.
To play the next music file, select ‚.
• Repeat
Configure Repeat mode. One song plays the current music file repeatedly. All plays all files in a folder repeatedly.
• Shuffle
Enable or disable shuffle playback mode.
• Sound Mode
Change the Sound Mode .
97
Supported Subtitle and Media play file formats
Subtitle
External
• MPEG-4 timed text (.ttxt)
• SAMI (.smi)
• SubRip (.srt)
• SubViewer (.sub)
• Micro DVD (.sub or .txt)
• SubStation Alpha (.ssa)
• Advanced SubStation Alpha (.ass)
• Powerdivx (.psb)
Internal
• Xsub
Container: AVI
• SubStation Alpha
Container: MKV
• Advanced SubStation Alpha
Container: MKV
• SubRip
Container: MKV
• MPEG-4 timed text
Container: MP4
Compatible image file format
Type
JPEG
MPO
BMP
98
Supported music file formats
File Extension
*.aac, *.flac, *.m4a, *.mid, *.midi,
*.mp3, *.mpa, *.ogg, *.wav, *.wma
Supported Video Formats
• Video content will not play, or not play correctly, if there is an error in the content or the container.
• Sound or video may not work if the contents have a standard bitrate/frame rate above the compatible Frame/sec listed in the table above.
• If the Index Table is in error, the Seek (Jump) function is not supported.
• You may experience file stuttering while playing a video through a network connection.
• The menu may take longer to appear if the video’s bit rate exceeds 10Mbps.
• Some USB/digital camera devices may not be compatible with the player.
Video Decoder
Supports up to H.264, Level 4.1
H.264 FMO / ASO / RS, VC1 SP / MP / AP L4 and AVCHD are not supported.
For all Video codecs except MVC, VP8, VP6:
• Below 1280 x 720: 60 frame max
• Above 1280 x 720: 30 frame max
GMC 2 over is not supported.
Supports only BD MVC Spec.
Audio Decoder
Supports up to WMA 10 Pro 5.1 channel.
WMA lossless audio is not supported.
QCELP, AMR NB/WB are not supported.
If Vorbis is only in Webm container, supports up to 2 channel.
99
Container
ps ts vob vro
3gpp asf avi flv mkv mov mp4
Video Codec
DivX 3.11 /DivX4
XVID
H.264 BP/MP/HP
MPEG-4 SP/ASP
WINDOW MEDIA VIDEO V9
MPEG2
MPEG1
H.263
DivX5
DivX6
Resolution
1280 x 720
Frame rate
(fps)
60
Bit rate
(Mbps)
30
Audio Codec
AAC
AC3
ADPCM
DD+
DTS Core
HE-AAC
LPCM
MP3
WMA
100
Container
ps ts vob vro
3gpp asf avi flv mkv mov mp4
Video Codec
DivX 3.11 /DivX4
XVID
H.264 BP/MP/HP
MPEG-4 SP/ASP
WINDOW MEDIA VIDEO V9
MPEG2
MPEG1
H.263
DivX5
DivX6
MOTION JPEG
Resolution
1920 x 1080
640 x 480
Frame rate
(fps)
30
30
Bit rate
(Mbps)
30
8
Audio Codec
AAC
AC3
ADPCM
DD+
DTS Core
HE-AAC
LPCM
MP3
WMA
101
Chapter 12
System
Setup
MENU m → System → Setup → ENTER E
System
Setup
Menu Language
Multi Control
Time
Eco Solution
Auto Protection Time
Screen Burn Protection
English
Off
The displayed image may differ depending on the model.
Initial settings (Setup)
After powering on the product for the first time, configure basic settings such as the language, channel and time.
Press the button. Setup is available only when Source is set to TV .
1 Selecting a language
Press the or button, and then press the E button. Specify the OSD menu language.
2 Regional Settings
Select your region to optimize system.
― The displayed image may differ depending on the model.
3
Configure the TV settings.
TV input source setup.
Set Channel Source to Set-top box to display the Source options.
Set-top box / Antenna / No TV (Signage Only)
4 Auto Tuning
This feature automatically searches and configures broadcast signals connected to the product.
To configure settings later, press the Stop button.
― Auto Tuning does not appear if Set-top box or No TV (Signage Only) is selected.
102
5
Network Settings
Select a wireless router from the list of retrieved routers and press the E button.
(See Connecting to a Wireless Network for more information.)
If a wireless router to connect to is not found, select the arrow on the right and press the Skip button.
6 Clock
Set the current date and time, and then select Next .
7 Setup Complete!
To watch TV using the product now, select OK .
103
Menu Language
MENU m → System → Menu Language → ENTER E
System
Menu Language English
The displayed image may differ depending on the model.
Set the menu language.
― A change to the language setting will only be applied to the onscreen menu display. It will not be applied to other functions on your PC.
104
Multi Control
MENU m → System → Multi Control → ENTER E
Multi Control
ID Setup
ID Input
PC Connection
00
--
Wi-Fi
The displayed image may differ depending on the model.
Configuring settings for Multi Control
• ID Setup
Assign an ID to a set. (Range: 0~99)
Press to select a number, and press E.
• ID Input
Enter the ID number of the product connected to the input cable for input signal reception.
Enter the number you want using the number buttons on the remote control.
• PC Connection
Select a method to connect to MDC to receive the MDC signal.
RS232C cable
Communicates with the MDC via a RS232C cable.
Wi-Fi
Communicate with MDC over Wi-Fi.
105
Time
MENU m → System → Time → ENTER E
Time
Clock
Sleep Timer
On Timer
Off Timer
Holiday Management
MagicInfo On/Off Timer
Off
The displayed image may differ depending on the model.
You can configure Clock . You can also set the product to automatically turn on or off at a specified time using the Timer function.
Clock
Clock Mode
Set the current time manually or automatically.
Auto : Have the product set the current time automatically using the time from a digital channel.
― You must have the cable or an antenna connected to the product to set the time automatically.
Manual : Set the current time manually.
Clock Set
Set the clock to use the various various timer features of the product.
Set the Date and Time .
Select Clock Set . Select Date or Time , and then press E.
Use the number buttons to enter numbers or press the up and down arrow buttons. Use the left and right arrow buttons to move from one entry field to the next. Press E when done.
― Available only when Clock Mode is set to Manual .
― You can set the Date and Time directly by pressing the number buttons on the remote control.
106
Time
Clock
Sleep Timer
On Timer
Off Timer
Holiday Management
MagicInfo On/Off Timer
The displayed image may differ depending on the model.
Off
Sleep Timer
Automatically shuts off the product after a preset period of time.
( Off / 30 min.
/ 60 min.
/ 90 min.
/ 120 min.
/ 150 min.
/ 180 min.
)
― Use the up and down arrows to select a period of time, and then press E. To cancel Sleep Timer , select Off .
On Timer
Set On Timer so that your product turns on automatically at a time and on a day of your choosing.
The power is turned on with the specified volume or input source.
On Timer : Set the on timer by making a selection from one of the seven options. Ensure you set the current time first.
( On Timer1 ~ On Timer7 )
― You must set the clock before you can use On Timer .
• Setup : Select Off , Once , Everyday , Mon~Fri , Mon~Sat , Sat~Sun or Manual . If you select Manual , you can choose the days you want On Timer to turn on your product.
― The check mark indicates days you’ve selected.
• Time : Set the hour and minute. Use the number buttons or the up and down arrow keys to enter numbers.
Use the left and right arrow buttons to change entry fields.
• Volume : Set the desired volume level. Use the left and right arrow buttons to change the volume level.
• Source : Select the input source of your choice.
• Antenna (when the Source is set to TV ): Select Air or Cable .
• Channel (when the Source is set to TV ): Select the desired channel.
• Music / Photo (when the Source is set to USB ): Select a folder in the USB device containing music or photo files you want played when the product turns on automatically.
― This function is available only when a USB device is connected.
― If there is no music file on the USB device or you don’t select a folder containing a music file, the Timer function does not operate correctly.
― If there is only one photo file in the USB, the Slide Show will not play.
― If a folder name is too long, the folder cannot be selected.
― Each USB you use is assigned its own folder. When using more than one of the same type of USB, make sure the folders assigned to each USB have different names.
― We recommend that you use a USB memory stick and a multi card reader when using On Timer . The On Timer function may not work with USB devices with a built-in battery, MP3 players, or PMPs made by some manufacturers because the product can take too long to recognize these devices.
107
Time
Clock
Sleep Timer
On Timer
Off Timer
Holiday Management
MagicInfo On/Off Timer
The displayed image may differ depending on the model.
Off
Off Timer
Set the off timer ( Off Timer ) by making a selection from one of the seven options. ( Off Timer1 ~ Off Timer7 )
― You must set the clock before you can use Off Timer .
• Setup : Select Off , Once , Everyday , Mon~Fri , Mon~Sat , Sat~Sun or Manual . If you select Manual , you can choose the days you want Off Timer to turn off your product.
― The check mark indicates days you’ve selected.
• Time : Set the hour and minute. Use the number buttons or the up and down arrow keys to enter numbers. Use the left and right arrow buttons to change entry fields.
Holiday Management
Timer will be disabled during a period specified as a holiday.
• Add : Specify the period you want to add as a holiday.
Select the start and end dates of the holiday you want to add using the / buttons, and click the Save button.
The period will be added to the list of holidays.
Start : Set the start date of the holiday.
End : Set the end date of the holiday.
Delete : Delete all items from the list of holidays.
Select Delete . The message " Delete all holidays?
" will appear.
Select Yes . All holidays will be deleted.
• Apply : Set the On Timer and Off Timer to not activate on public holidays.
Press E to select the On Timer and Off Timer settings you do not want to activate.
The selected On Timer and Off Timer will not activate.
108
Time
Clock
Sleep Timer
On Timer
Off Timer
Holiday Management
MagicInfo On/Off Timer
The displayed image may differ depending on the model.
Off
MagicInfo On/Off Timer
View the on/off timer settings configured in the MagicInfo Express Content Creator tool.
• On Timer
Setup : View the days of the week specified in the MagicInfo Express Content Creator tool for the on timer to turn on the product.
Time : View the time specified in the MagicInfo Express Content Creator tool for the on timer to turn on the product.
Source : View the content input source specified in the MagicInfo Express Content Creator tool.
• Off Timer
Setup : View the days of the week specified in the MagicInfo Express Content Creator tool for the off timer to turn off the product.
Time : View the time specified in the MagicInfo Express Content Creator tool for the off timer to turn off the product.
109
Eco Solution
MENU m → System → Eco Solution → ENTER E
Eco Solution
Energy Saving
Eco Sensor
No Signal Power Off
Auto Power Off
Off
Off
15 min.
Off
The displayed image may differ depending on the model.
Energy Saving
Reduce the power consumption by adjusting the screen brightness.
Selecting Picture Off switches off the screen. The volume is not disabled.
To switch the screen on, press any button other than the volume button.
• Off / Low / Medium / High
Eco Sensor
Eco Sensor
To enhance your power savings, the picture settings will automatically adapt to the light in the room.
• Off / On
― Adjusting the Backlight setting under Picture while Eco Sensor is on will disable the Off .
Min. Backlight
When Eco Sensor is On , you can manually adjust the minimum screen brightness. Min. Backlight is the darkest backlight mode. Make sure the Min. Backlight setting is lower than the Backlight setting.
― If Eco Sensor is On , the display brightness may change (become slightly darker or brighter) depending on the surrounding light intensity.
110
Eco Solution
Energy Saving
Eco Sensor
No Signal Power Off
Auto Power Off
The displayed image may differ depending on the model.
Off
Off
15 min.
Off
No Signal Power Off
Save power by turning the device off when no signal is received from any source.
• Off / 15 min.
/ 30 min.
/ 60 min.
― Disabled when an attached PC is in power saving mode.
― The product will automatically power off at a specified time. The time can be changed as required.
Auto Power Off
The product will automatically turn off if you don’t press a button on the remote or touch a button on product front panel within 4 hours to prevent overheating.
• Off / On
111
Auto Protection Time
MENU m → System → Auto Protection Time → ENTER E
System
Auto Protection Time Off
The displayed image may differ depending on the model.
If the screen displays a still image for a certain period of time you define, the product activates the screen saver to prevent the formation of burnt in ghost images on the screen.
― Displaying a still image for longer than four hours can cause image retention.
• Off / 2 hours / 4 hours / 8 hours / 10 hours
112
Screen Burn Protection
MENU m → System → Screen Burn Protection → ENTER E
Screen Burn Protection
Pixel Shift
Timer
Immediate Display
Side Gray
Off
Off
Off
Off
The displayed image may differ depending on the model.
To reduce the possibility of screen burn, this unit is equipped with Pixel Shift screen burn prevention technology.
Pixel Shift moves the picture slightly on the screen.
The Pixel Shift Time setting allows you to program the time between movements of the picture in minutes.
Pixel Shift
Minimize image retention by finely moving pixels horizontally or vertically.
• Pixel Shift ( Off / On )
Horizontal : Sets how many pixels the screen moves horizontally.
Vertical : Sets how many pixels the screen moves vertically.
Time : Set the time interval for performing the horizontal or vertical movement, respectively.
― Horizontal , Vertical and Time are enabled only when Pixel Shift is set to On .
Available Pixel Shift Settings and Optimum Settings.
Available Settings Optimum Settings
Horizontal (pixels) 0 ~ 4 4
Vertical (pixels) 0~4 4
Time (minute) 1 min. ~ 4 min.
4 min.
― The Pixel Shift value may differ depending on the product size and mode.
― Displaying a still image or a 4:3 output for an extended period of time may cause image retention. This is not a defect in the product.
― This function is not available in the Screen Fit mode.
113
Screen Burn Protection
Pixel Shift
Timer
Immediate Display
Side Gray
The displayed image may differ depending on the model.
Off
Off
Off
Off
Timer
You can set the timer for Screen Burn Protection .
The Timer feature stops automatically after a specified period of time.
Timer
• Off
• Repeat : Display the image retention-preventive pattern set in Mode at specified time intervals(Period).
• Interval : Display the image retention-preventive pattern set in Mode for a specified period of time (from Start Time to
End Time ).
― The option is enabled only when Clock Set is configured.
― Mode , Period , Time , Start Time and End Time are enabled only when Timer is set to Repeat or Interval .
Mode
Select a screen protective pattern to display.
• Pixel : Pixels on the screen alternate black continuously.
• Rolling Bar : A vertical bar moves left to right.
• Fading Screen : The entire screen becomes brighter, then darker.
― The Rolling Bar and Fading Screen patterns appear only once regardless of the specified repeat period or time.
Period
Specify the time interval to activate the Screen Burn Protection function.
― The option is enabled when Repeat is selected for Timer .
Time
Specify the duration to keep the Screen Burn Protection function on.
― The option is enabled when Pixel is selected for Mode .
114
Start Time
Set the start time to activate the screen protection function.
― The option is enabled when Interval is selected for Timer .
End Time
Set the end time to deactivate the screen protection function.
― The option is enabled when Interval is selected for Timer .
115
Screen Burn Protection
Pixel Shift
Timer
Immediate Display
Side Gray
The displayed image may differ depending on the model.
Off
Off
Off
Off
Immediate Display
Select the screen saver you want to display immediately.
• Off / Pixel / Rolling Bar / Fading Screen
Side Gray
When the screen is set to 4:3 aspect ratio, adjust the brightness of white margins on sides to protect the screen.
• Off / Light / Dark
116
Ticker
MENU m → System → Ticker → ENTER E
Ticker
Ticker
· Message
· Time
· Position
· Motion
· Font Style
Off
Off
The displayed image may differ depending on the model.
The Ticker function is only available when Menu Language is set to English .
Ticker
Input text while a video or image is displayed and display the text on the screen.
• Off / On
― Message , Time , Position , Motion , and Font Options are enabled only when Ticker is set to On .
Message
Enter a message to display on the screen.
Time
Set the Start Time and End Time to display a Message .
• Start Time
• End Time
Position
Select an orientation to display a Message from Horizontal and Vertical .
• Horizontal ( Left / Center / Right )
• Vertical ( Up / Middle / Down )
Motion
Specify the Direction and Speed to display a Message .
• Motion ( Off / On )
• Direction ( Left / Right / Up / Down )
• Speed ( Slow / Normal / Fast )
― Direction and Speed are enabled only when Motion is set to On .
Font Style
Configure the message font options.
117
Source AutoSwitch Settings
MENU m → System → Source AutoSwitch Settings → ENTER E
Source AutoSwitch Settings
Source AutoSwitch
· Primary Source Recovery
· Primary Source
· Secondary Source
Off
Off
All
HDMI
The displayed image may differ depending on the model.
Turning on the display with Source AutoSwitch On , and the previous video source selection is not active, the display will automatically search the different video input sources for active video.
Source AutoSwitch
When the Source AutoSwitch is On , the display video source will automatically be searched for active video.
The Primary Source selection will be activated, if the current video source is not recognized.
Secondary Source selection will become active, if no primary video source is available.
If both the primary and secondary input sources are not recognized, the display will perform two searches for an active source, each search checking the primary and then secondary source. If both searches fail, the display will return to the first video source and display a message indicating that there is no signal.
When the Primary Source selection is set to All , the display will search all the video source inputs twice in sequence looking for an active video source, returning back to the first video source in the sequence if no video is found.
Primary Source Recovery
Select whether to restore the selected primary input source when a primary input source is connected.
― The Primary Source Recovery function is disabled if Primary Source is set to All .
Primary Source
Specify Primary Source for the automatic input source.
Secondary Source
Specify Secondary Source for the automatic input source.
118
General
MENU m → System → General → ENTER E
General
Game Mode
Auto Power
Safety Lock
Button Lock
USB Auto Play Lock
Standby Control
Lamp Schedule
Off
Off
Auto
Off
Off
Off
Off
The displayed image may differ depending on the model.
Game Mode
When connecting to a game console such as PlayStation™ or Xbox™, you can enjoy a more realistic gaming experience by selecting game mode.
• Off / On
― Precautions and limitations for Game Mode
To disconnect the game console and connect another external device, set Game Mode to Off in the setup menu.
― Game Mode is not available when the input source is set to TV . After connecting the game console, set Game Mode to
On . Unfortunately, you may notice reduced picture quality.
― If Game Mode is On
Picture Mode is set to Standard and Sound Mode is set to Movie .
Auto Power
Enabling this option will automatically power on the product if the power cable is connected.
• Off / On
Safety Lock
It sets safe lock function.
• Off / On
All the menus and buttons of the product and remote control, except for the LOCK button on the remote control, will be locked by the Safety Lock function.
To unlock the menus and buttons, press the LOCK button and then enter the password (default password: 0 - 0 - 0 - 0).
Button Lock
It sets safe lock function.
• Off / On
This menu can be used to lock the buttons on the product.
Only the remote control can control the product if Button Lock is set to On .
119
General
USB Auto Play Lock
Standby Control
Lamp Schedule
OSD Display
AV Color System
Off
Auto
Off
Auto
The displayed image may differ depending on the model.
USB Auto Play Lock
Select whether to automatically play MagicInfo content saved on a connected USB device.
• On
Do not play MagicInfo content saved on the USB device automatically.
― Connecting a USB device containing MagicInfo content displays " USB Auto Play Lock : On " for five seconds.
• Off
Play MagicInfo content saved on the USB device automatically.
Standby Control
You can set the screen standby mode to be applied when an input signal is received.
• Auto
Power-saving mode will activate if no input signals are detected even though a source device is connected to the display.
The message No Signal will appear if no source device is connected.
• On
Power-saving mode will activate if no input signals are detected.
• Off
The message No Signal will appear if no input signals are detected.
― The Standby Control option is only enabled when Source is set to HDMI .
― If No Signal is displayed although a source device is connected, check the cable connection.
Lamp Schedule
Adjusts the luminance to a user-specified value at a specified time.
• Off / On
OSD Display
Displays or hides a menu item on the screen.
• Source OSD : Off / On
• No Signal OSD : Off / On
120
General
USB Auto Play Lock
Standby Control
Lamp Schedule
OSD Display
AV Color System
Off
Auto
Off
Auto
The displayed image may differ depending on the model.
AV Color System
Change the Color System according to the AV signal.
• Auto / PAL-M / PAL-N / NTSC
121
Change PIN
MENU m → System → Change PIN → ENTER E
System
Change PIN
The displayed image may differ depending on the model.
The Change PIN screen will appear.
Choose any 4 digits for your PIN and enter it in Enter New PIN . Reenter the same 4 digits in Confirm New PIN .
When the Confirm screen disappears, press the Close button. The product has memorized your new PIN.
― Default password: 0 - 0 - 0 - 0
122
Clone Product
MENU m → System → Clone Product → ENTER E
Clone Product
Clone to USB
Clone From USB
The displayed image may differ depending on the model.
Reset System
MENU m → System → Reset System → ENTER E
System
Reset System
The displayed image may differ depending on the model.
Export the product settings to a USB device or load the settings via a USB device.
This option is useful when assigning the same settings to several products.
• Clone to USB : Copy the product settings to a USB device.
• Clone From USB : Assign the settings saved in a USB device to the product.
After configuration is complete, the product is rebooted automatically.
― The option may not work properly if the USB device contains a file other than a settings file.
― Confirm that the USB device functions properly before running the option.
― The option is available for products with the same Model Code and Software Version .
Go to Support → Contact Samsung and find the product Model Code and Software Version .
This option returns the current settings under system to the default factory settings.
123
Reset All
MENU m → System → Reset All → ENTER E
System
Reset All
The displayed image may differ depending on the model.
DivX® Video On Demand
MENU m → System → DivX® Video On Demand → ENTER E
System
DivX® Video On Demand
The displayed image may differ depending on the model.
This option returns all the current settings for a display to the default factory settings.
Shows the registration code authorized for the product.
If you connect to the DivXⓇ web site and register using that code, you can download the VOD registration file.
For more information about DivXⓇ VOD, visit “http://vod.divx.com”.
124
Chapter 13
Support
Current Version : This is the software version already installed in the product.
Software Update
MENU m → Support → Software Update → ENTER E
The Software Update menu lets you upgrade your product software to the latest version.
― Be careful not to turn off the power until the upgrade is complete. The product will turn off and on automatically after completing the software upgrade.
― When you upgrade software, all video and audio settings you have made will return to their default settings. We advise you to write down your settings so that you can easily reset them after the upgrade.
Update now
Update the software to the latest version.
― Performing a software update via USB will display the corresponding update window after a maximum of two minutes.
Contact Samsung
MENU m → Support → Contact Samsung → ENTER E
View this information when your product does not work properly or when you want to upgrade the software.
You can find information regarding our call centers and how to download products and software.
― Contact Samsung and find the product Model Code and Software Version .
125
Chapter 14
Troubleshooting Guide
Before calling Samsung Customer Service
Center, test your product as follows. If the problem persists, contact Samsung
Customer Service Center.
If the screen remains blank, check the PC system, video controller and cable.
Requirements Before Contacting Samsung Customer Service Center
Testing the Product
Check if your product is operating normally by using the product test function.
If the screen remains blank while the power LED blinks even when the product is correctly connected to a PC, perform product testing.
1
Power off both the PC and product.
2
Disconnect all the cables from the product.
3 Power on the product.
4 If No Signal is displayed, the product is operating normally.
Checking the Resolution and Frequency
Not Optimum Mode will briefly be displayed if a mode that exceeds a supported resolution is selected (refer to Supported Resolutions).
126
Check the followings.
Installation issue (PC mode)
The screen keeps switching on and off.
Check the cable connection between the product and PC, and ensure the connection is secure.
Blank spaces are found on all four sides of the screen when an HDMI or HDMI-DVI cable is connected to the product and
PC.
The blank spaces found on the screen have nothing to do with the product.
Blank spaces on the screen are caused by the PC or graphics card. To resolve the problem, adjust the screen size in the HDMI or DVI settings for the graphics card.
If the graphics card settings menu does not have an option to adjust the screen size, update the graphics card driver to the latest version.
(Please contact the graphics card or computer manufacturer for further details about how to adjust the screen settings.)
Screen issue
The power LED is off. The screen will not switch on.
No Cable Connected is displayed on the screen (refer to
"Connecting to a PC").
Not Optimum Mode is displayed.
The images on the screen look distorted.
The screen is not clear. The screen is blurry.
Make sure that the power cord is connected.
Check that the product is connected correctly with a cable.
Check that the device connected to the product is powered on.
This message is displayed when a signal from the graphics card exceeds the product's maximum resolution and frequency.
Refer to the Standard Signal Mode Table and set the maximum resolution and frequency according to the product specifications.
Check the cable connection to the product.
Remove any accessories (video extension cable, etc) and try again.
Set the resolution and frequency to the recommended level.
127
Screen issue
The screen appears unstable and shaky.
There are shadows or ghost images left on the screen.
The screen is too bright. The screen is too dark.
Screen color is inconsistent.
White does not really look white.
There is no image on the screen and the power LED blinks every 0.5 to 1 second.
The product will turn off automatically.
Check that the resolution and frequency of the PC and graphics card are set within a range compatible with the product. Then, change the screen settings if required by referring to the Additional
Information on the product menu and the Standard Signal Mode Table.
Adjust Brightness and Contrast .
Go to Picture and adjust the Color Space settings.
Go to Picture and adjust the White Balance settings.
The product is in power-saving mode.
Press any key on the keyboard or move the mouse to return to the previous screen.
Go to System and make sure Sleep Timer is set to Off .
If a PC is connected to the product, check the power status of the PC.
Make sure the power cable is connected properly to the product and power outlet.
If the signal from a connected device is not detected, the product automatically turns off after 10 to 15 minutes.
Use an HDMI cable to obtain high-definition (HD) picture quality.
Picture quality of the product is different from the dealer shop where it was purchased.
The screen display does not look normal.
Encoded video content may cause the display to appear corrupted in scenes featuring fast moving objects such as in a sports event or action video.
Low signal level or low picture quality may cause the display to appear corrupted. This does not mean the product is defective.
A cell phone within a distance of one-meter radius may cause static on analog and digital products.
128
Screen issue
The brightness and color do not look normal.
Broken lines are displayed on the edges of the screen.
Lines (red, green or blue) are displayed on the screen.
The display looks unstable and then freezes.
The screen cannot be displayed in full screen.
Go to Picture and adjust the screen settings such as Picture Mode , Color , Brightness and
Sharpness .
Go to System and adjust the Eco Solution settings.
Reset the screen settings to the default settings.
If Picture Size is set to Screen Fit , change the setting to 16:9 .
These lines are displayed when there is a defect in DATA SOURCE DRIVER IC on the product. Contact a
Samsung Service Center to resolve the issue.
The screen may freeze when a resolution other than the recommended resolution is used or if the signal is not stable. To resolve the issue, change the PC resolution to the recommended resolution.
A scaled SD (4:3) content file can cause black bars on both sides of an HD channel screen.
A video with an aspect ratio different from the product can cause black bars at the top and bottom of the screen.
Change the screen size setting to full screen on the product or source device.
Sound issue
There is no sound.
The volume is too low.
Check the connection of the audio cable or adjust the volume.
Check the volume.
Adjust the volume.
If the volume is still low after turning it up to the maximum level, adjust the volume on your PC sound card or software program.
129
Sound issue
Video is available but there is no sound.
There is static coming from the speakers.
If an HDMI cable is connected, check the audio output settings on the PC.
If a source device is used
• Make sure the audio cable is properly connected to the audio input port on the product.
• Check the audio output settings for the source device.
(For example, if an HDMI cable is connected to the product, the audio setting for the cable box may need to be changed to HDMI.)
Reconnect the power cable to the device and then reboot the device.
Check the cable connection. Make sure a video cable is not connected to an audio input port.
Check the signal strength after connecting a cable.
Low signal level can cause corrupted sound.
There is audible sound when the volume is muted.
Audio settings for main speakers are separate from the internal speakers on the product.
Changing or muting the volume on the product does not affect an external amplifier(decoder).
Sound from the product does not change after Sound Mode is changed.
Audio settings for main speakers are separate from the internal speakers on the product.
Audio settings on a source device do not affect the internal speaker settings on the product.
130
Remote control issue
The remote control does not work.
Make sure that the batteries are correctly in place (+/-).
Check if the batteries are flat.
Check for power failure.
Make sure that the power cord is connected.
Check for any special lighting or neon signs switched on in the vicinity.
Source device issue
A beeping sound is heard when my PC is booting.
Other issue
Caption is grayed out and not selectable.
The product smells like plastic.
The product appears tilted.
Audio or video cuts out intermittently.
Small particles are found on the edges of the product.
The PIP menu is not available.
If a beeping sound is heard when your PC is booting, have your PC serviced.
If the selected input source is not TV , Caption cannot be selected from the Channel menu.
The plastic smell is normal and disappears over time.
Remove and then attach the stand again to the product.
Check the cable connection and connect it again if required.
Using a very hard or thick cable may corrupt audio and video files.
Make sure cables are flexible enough to ensure durability. When mounting the product onto a wall, it is recommended to use right-angle cables.
The particles are part of the product design. The product is not defective.
The menu is enabled or disabled depending on the Source mode.
131
Other issue
When I try to change the PC resolution, a message The defined resolution is not currently supported.
appears.
There is no sound from the speakers in HDMI mode when a
DVI-HDMI cable is connected.
HDMI Black Level is not functioning properly on an HDMI device with YCbCr output.
There is no sound in HDMI mode.
The message The defined resolution is not currently supported.
appears if the input source resolution exceeds the maximum resolution of the display.
To resolve the issue, change the PC resolution to a resolution supported on the display.
DVI cables do not transmit sound data.
Make sure to connect the audio cable to the correct input jack to enable audio.
This function is available only when a source device, such as a DVD player and STB, is connected to the product via an HDMI (RGB signal) cable.
Displayed picture colors may not look normal. Video or sound may not be available. This can occur if a source device that only supports an older version of the HDMI standard is connected to the product. If these issues occur, connect an audio cable along with the HDMI cable.
Some PC graphics cards may not automatically recognize HDMI signals that do not include sound. In this case, manually select a sound input.
PC
Sound input
Auto
Screen mode
PC settings
132
Refer to the user manual for your PC or graphics card for further instructions on adjustment.
Q & A
Question
How can I change the frequency?
How can I change the resolution?
Answer
Set the frequency on your graphics card.
• Windows XP: Go to Control Panel → Appearance and Themes → Display → Settings →
Advanced → Monitor and adjust the frequency in Monitor Settings.
• Windows ME/2000: Go to Control Panel → Display → Settings → Advanced → Monitor and adjust the frequency in Monitor Settings.
• Windows Vista: Go to Control Panel → Appearance and Personalization → Personalize →
Display Settings → Advanced Settings → Monitor and adjust the frequency in Monitor
Settings.
• Windows 7: Go to Control Panel → Appearance and Personalization → Display → Adjust resolution → Advanced Settings → Monitor and adjust the frequency in Monitor Settings.
• Windows 8: Go to Settings → Control Panel → Appearance and Personalization → Display
→ Adjust resolution → Advanced Settings → Monitor and adjust the frequency in Monitor
Settings.
• Windows XP: Go to Control Panel → Appearance and Themes → Display → Settings and adjust the resolution.
• Windows ME/2000: Go to Control Panel → Display → Settings and adjust the resolution.
• Windows Vista: Go to Control Panel → Appearance and Personalization → Personalize →
Display Settings and adjust the resolution.
• Windows 7: Go to Control Panel → Appearance and Personalization → Display → Adjust
Resolution and adjust the resolution.
• Windows 8: Go to Settings → Control Panel → Appearance and Personalization → Display
→ Adjust Resolution and adjust the resolution.
133
Question
How do I set powersaving mode?
Answer
• Windows XP: Set power-saving mode in Control Panel → Appearance and Themes → Display
→ Screen Saver Settings or BIOS SETUP on the PC.
• Windows ME/2000: Set power-saving mode in Control Panel → Display → Screen Saver
Settings or BIOS SETUP on the PC.
• Windows Vista: Set power-saving mode in Control Panel → Appearance and Personalization
→ Personalize → Screen Saver Settings or BIOS SETUP on the PC.
• Windows 7: Set power-saving mode in Control Panel → Appearance and Personalization →
Personalize → Screen Saver Settings or BIOS SETUP on the PC.
• Windows 8: Set power-saving mode in Settings → Control Panel → Appearance and
Personalization → Personalize → Screen Saver Settings or BIOS SETUP on the PC.
134
Chapter 15
Specifications
- Size
- Display area
H
V
- Dimensions (W x H x D)
D
H
General
Model Name
Panel
Dimensions
(W x H x D) /
Weight
Audio Output
Power Supply
Size
Display area
Without Stand
With Stand
Environmental considerations
Operating
Storage
EB40D
40 CLASS (40.0 inches / 101 cm)
88.82 cm (H) x 50.07 cm (V)
91.42 x 54.79 x 9.09 cm / 7.0 kg
91.42 x 58.64 x 19.64 cm / 7.6 kg
EB48D
48 CLASS (47.6 inches / 120 cm)
105.62 cm (H) x 59.51 cm (V)
108.32 x 63.78 x 9.09 cm / 9.1 kg
108.32 x 67.70 x 20.39 cm / 9.9 kg
10 W + 10 W
AC 100 to 240 VAC (+/- 10%), 60 / 50Hz ± 3Hz
Refer to the label at the back of the product as the standard voltage can vary in different countries.
Temperature : 32 F - 104 F (0 C - 40 C)
Humidity : 10 % - 80 %, non-condensing
Temperature : -4 F - 113 F (-20 C - 45 C)
Humidity : 5 % - 95 %, non-condensing
W
135
― Plug-and-Play
This monitor can be installed and used with any Plug-and-Play compatible systems. Two-way data exchange between the monitor and PC system optimizes the monitor settings.
Monitor installation takes place automatically. However, you can customize the installation settings if desired.
― Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may appear brighter or darker on the panel. This does not affect product performance.
― This device is a Class A digital apparatus.
136
Power Consumption
Normal Operation
Rating
70 W
Stand-by
Power Consumption EB40D
EB48D
Lower than 0.5 W
84 W
― The displayed power consumption level can vary in different operating conditions or when settings are changed.
― SOG(Sync On Green) is not supported.
― To reduce the power consumption to 0, disconnect the power cord. Disconnect the power cable if you will not be using the product for an extended period of time (during vacation, etc.)
137
Horizontal Frequency
The time required to scan a single line from the left to the right side of the screen is called a horizontal cycle. The reciprocal number of a horizontal cycle is called horizontal frequency. Horizontal frequency is measured in kHz.
Vertical Frequency
The product displays a single image multiple times per second (like a fluorescent light) to display what the viewer sees. The rate of a single image being displayed repeatedly per second is called vertical frequency or refresh rate.
Vertical frequency is measured in Hz.
Preset Timing Modes
― This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Using a resolution other than the specified resolution may degrade the picture quality. To avoid this, it is recommended that you select the optimum resolution specified for your product.
― Check the frequency when you exchange a CDT product (connected to a PC) for an LCD product. If the LCD product does not support 85Hz, change the vertical frequency to 60Hz using the CDT product before you exchange it with the LCD product.
Model Name
Synchronization
EB48D
Resolution
Horizontal Frequency
Vertical Frequency
Optimum resolution
Maximum resolution
EB40D
30 - 61 kHz
60 - 75 Hz
1366 x 768 @ 60 Hz
1366 x 768 @ 60 Hz
The screen will automatically be adjusted if a signal that belongs to the following standard signal modes is transmitted from your PC. If the signal transmitted from the PC does not belong to the standard signal modes, the screen may be blank with the power LED on. In such a case, change the settings according to the following table by referring to the graphics card user manual.
Resolution
VESA, 640 x 480
Horizontal Frequency
(kHz)
31.469
Vertical Frequency
(Hz)
59.940
Pixel Clock
(MHz)
25.175
Sync Polarity
(H/V)
-/-
IBM, 720 x 400
MAC, 640 x 480
VESA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
31.469
35.000
37.861
37.500
37.879
70.087
66.667
72.809
75.000
60.317
28.322
30.240
31.500
31.500
40.000
-/-
-/-
-/+
-/-
+/+
138
Resolution
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1280 x 720
VESA, 1366 x 768
Horizontal Frequency
(kHz)
48.077
46.875
48.363
56.476
60.023
45.000
47.712
Vertical Frequency
(Hz)
72.188
75.000
60.004
70.069
75.029
60.000
59.790
Pixel Clock
(MHz)
50.000
49.500
65.000
75.000
78.750
74.250
85.500
+/+
-/-
-/-
+/+
+/+
+/+
Sync Polarity
(H/V)
+/+
139
Chapter 16
Appendix
Responsibility for the Pay Service
(Cost to Customers)
― When the service is requested, in spite of in warranty, we may charge you for a visit from a service technician in the following cases.
Not a product defect
Cleaning of the product, Adjustment, Explanation, Re-installation and etc.
• If a service technician gives instructions on how to use product or simply adjusts options without disassembling product.
• If a defect is caused by external environmental factors (Internet, Antenna, Wired Signal, etc.)
• If a product is reinstalled or devices are connected additionally after installing the purchased product for the first time.
• If a product is reinstalled to move to a different spot or to move to a different house.
• If customer requests instructions on how to use because of another company's product.
• If customer requests instructions on how to use the network or another company's program.
• If customer requests software installation and setup for the product.
• If a service technician removes/cleans dusts or foreign materials inside of the product.
• If customer requests an installation additionally after purchasing a product through homeshopping or online.
A Product damage caused by customer's fault
Product damage caused by customer's mishandling or wrong repair
If a product damage is caused by;
• External impact or drop.
• Use of supplies or separatly sold product unspecified by Samsung.
• Repair from a person besides an engineer of outsourcing service company or partner of Samsung
Electronics Co., Ltd.
• Remodeling or repairing the product by customer.
• Using it with incorrect voltage or non-authorised electrical connections.
• Not following the "cautions" in User Manual.
Others
• If product fails by natural disaster. (lightning, fire, earthquake, flood damage, etc)
• If consumable components are all used up. (Battery, Toner, Fluorescent lights, Head, Vibrator, Lamp,
Filter, Ribbon, etc.)
― If customer requests a service in case the product has no defect, service fee may be charged. So please read User Manual first.
140
Optimum Picture Quality and Afterimage
Burn-in Prevention
Optimum Picture Quality
Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may be brighter or darker on the panel.
This does not affect product performance.
The number of sub-pixels by panel type: 6,220,800
• Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage burn-in or defective pixels.
Activate power-saving mode or a dynamic screen saver if you will not be using the product for an extended period of time.
Prevention of Afterimage Burn-in
What is afterimage burn-in?
Afterimage burn-in should not occur when the LCD panel is operating normally. Normal operation refers to a continuously changing video pattern. If the LCD panel displays a fixed pattern for an extended period of time (more than 12 hours), a slight voltage difference may occur between the electrodes in pixels that control the liquid crystals.
Such a voltage difference between electrodes increases with time and makes the liquid crystals thinner.
When this occurs, a previous image can remain on the screen when the pattern changes. To prevent this, the accumulated voltage difference should be reduced.
― Afterimage burn-in should not occur when an LCD panel is operating in proper conditions.
Black Matrix
Source Drain
TFT
Data Bus-Line
Gate
Common
Electrode (ITO)
Color-Filter
Pixel Electrode (ITO)
Storage
Capaccitor (Cs)
141
Preventing afterimage burn-in
― The best way to protect the product from afterimage burn-in is switching the power off or setting the
PC or system to run a screen saver when not in use. Also, Warranty service may be limited depending on instruction guide.
• Powering Off, Screen Saver and Power Saving Mode
Go to Display Properties > Power Supply on your PC and set the product to power off as required.
Using a screen saver is recommended.
It is best to use a single-color or moving-image screen saver.
• Regular color Change
Use 2 colors
Switch between 2 colors every 30 minutes as shown above.
Type 1
FLIGHT
OZ348
TIME
20:30
UA102 21:10
Type 2
FLIGHT
OZ348
TIME
20:30
UA102 21:10
• Avoid combinations of a text color and background color of contrasting brightness.
(Brightness: refers to the lightness or darkness of a color which varies depending on the amount of light emitted.)
― Avoid using grey as it may contribute to afterimage burn-in.
― Avoid using colors of contrasting brightness (black and white; grey).
FLIGHT : TIME
OZ348 : 20:30
FLIGHT : TIME
OZ348 : 20:30
• Regular Text color Change
Use bright colors of similar brightness.
Interval: Change text color and background color every 30 minutes
FLIGHT : TIME
OZ348 : 20:30
FLIGHT : TIME
OZ348 : 20:30
FLIGHT : TIME
OZ348 : 20:30
FLIGHT
OZ348 :
: TIME
20:30
Move and change text every 30 minutes as shown below.
FLIGHT
OZ348 :
: TIME
20:30
[ Step 1 ] [ Step 2 ]
FLIGHT
OZ348 :
: TIME
20:30
[ Step 3 ]
Regularly display a moving image along with a logo.
Interval: Display a moving image along with a logo for 60 seconds after using for 4 hours.
142
License
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
2.0 Channel
Ⓡ
Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380;
6,487,535 & other U.S. and worldwide patents issued & pending. DTS, the
Symbol, & DTS and the Symbol together are registered trademarks & DTS 2.0
Channel is a trademark of DTS, Inc. ⓒ DTS, Inc. All Rights Reserved.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the
HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
DivX Certified Ⓡ to play DivX Ⓡ video up to HD 1080p, including premium content.
DivXⓇ, DivX CertifiedⓇ and associated logos are trademarks of Rovi
Corporation or its subsidiaries and are used under license.
ABOUT DIVX VIDEO: DivXⓇ is a digital video format created by DivX, LLC, a subsidiary of Rovi
Corporation. This is an official DivX CertifiedⓇ device that has passed rigorous testing to verify that it plays DivX video. Visit divx.com for more information and software tools to convert your files into
DivX videos.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX CertifiedⓇ device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the
DivX VOD section in your device setup menu. Go to vod.divx.com for more information on how to complete your registration.
Covered by one or more of the following U.S. patents: 7,295,673; 7,460,668; 7,515,710; 7,519,274
Open Source Licence Notice
In the case of using open source software, Open Source Licences are available on the product menu.
Open Source Licence Notice is written only English.
For information on the Open Source License Notice, contact the Samsung Customer Center or send email to [email protected].
143
Terminology
480i / 480p / 720p / 1080i /
1080p____ Each of the scanning rates above refers to the number of effective scanning lines that decides the screen resolution. The scanning rate may be indicated in i (interlaced) or p (progressive), depending on the scanning method.
- Scanning
Scanning refers to a process of sending pixels that form an image progressively.
A larger number of pixels will deliver a clearer and more vivid picture.
- Progressive
In progressive scan mode, all lines of pixels are scanned one by one
(progressively) on the screen.
- Interlaced
In interlaced scan mode, every other line of pixels is scanned from top to bottom first and then the remaining lines of pixels (that were not scanned) are scanned.
Non-interlace Mode and Interlace
Mode____ Non-interlace mode
(progressive scan) displays a horizontal line from the top to the bottom of a screen progressively. Interlace mode displays the odd number lines first and the even number lines next. Noninterlace mode is mainly used in monitors as it produces screen clarity and interlace mode is mainly used in
TVs.
Dot Pitch____ The screen consist of red, green and blue dots. A shorter distance between the dots produces a higher resolution. Dot pitch refers to the distance between the shortest distance between dots of the same color. Dot pitch is measured in millimeters.
Vertical Frequency____ The product displays a single image many times per second (like a fluorescent light that flickers) to display an image for a viewer to see. The rate of a single image being displayed repeatedly per second is called vertical frequency or refresh rate.
Vertical frequency is measured in Hz.
E.g. 60Hz refers to a single image being displayed 60 times in one second.
Horizontal Frequency____ The time required to scan a single line from the left to the right side of the screen is called a horizontal cycle. The reciprocal number of a horizontal cycle is called horizontal frequency. Horizontal frequency is measured in kHz.
Source____ Input source refers to a video source device connected to the product such as a camcorder or video or DVD player.
Plug & Play____ Plug & Play is a function that allows the automatic exchange of information between a product and PC to produce an optimum display environment. The product uses
VESA DDC (international standard) to execute Plug & Play.
Resolution____ Resolution is the number of horizontal dots (pixels) and vertical dots (pixels) that form a screen.
It represents the level of display detail.
A higher resolution enables more data to be displayed on the screen and is useful to perform multiple tasks simultaneously.
E.g. A resolution of 1920 X 1080 consists of 1,920 horizontal pixels (horizontal resolution) and 1,080 vertical pixels
(vertical resolution).
DVD (Digital Versatile Disc)____ DVD refers to a CD-sized mass storage disk where you can save multimedia (audio, video or game) applications using
MPEG-2 video compression technology.
HDMI (High Definition Multimedia
Interface)____ It is an interface that can be connected to a digital audio source as well as a high-definition video source by using a single cable without compression.
Multiple Display Control (MDC)____
MDC (Multiple Display Control) is an application that allows multiple display devices to be controlled simultaneously using a PC. Use RS232C (serial data communication standard) and Wi-Fi to transmit data between the PC and monitor.
144
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- Digital signage flat panel Black
- 121.9 cm (48") 1366 x 768 pixels LED 250 cd/m²
- 6 ms
- Built-in speaker(s) 20 W
Related manuals
advertisement