IdeaPad S9e and S10e Hardware Maintenance Manual

IdeaPad S9e and S10e Hardware Maintenance Manual
™
IdeaPad S9e and S10e
Hardware Maintenance Manual
™
IdeaPad S9e and S10e
Hardware Maintenance Manual
Note
Before using this information and the product it supports, be sure to read the general information under “Notices” on page
115.
First Edition (November 2008)
© Copyright Lenovo 2008. All rights reserved.
LENOVO products, data, computer software, and services have been developed exclusively at private expense and
are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted
rights to use, reproduction and disclosure.
LIMITED AND RESTRICTED RIGHTS NOTICE: If products, data, computer software, or services are delivered
pursuant a General Services Administration ″GSA″ contract, use, reproduction, or disclosure is subject to restrictions
set forth in Contract No. GS-35F-05925.
© 2008 Lenovo
Contents
About this manual . . . . . . . . . . v
Safety information . . . . . . . . . . 1
General safety . . . . . . . . . . . . . . 2
Electrical safety . . . . . . . . . . . . . 3
Safety inspection guide . . . . . . . . . . . 5
Handling devices that are sensitive to electrostatic
discharge . . . . . . . . . . . . . . . 6
Grounding requirements . . . . . . . . . . 6
Safety notices: multilingual translations . . . . . 7
Laser compliance statement . . . . . . . . . 14
Important service information . . . . . 17
Strategy for replacing FRUs . . . . . . . .
Strategy for replacing a hard disk drive . . .
Important notice for replacing a system board .
How to use error message . . . . . . .
Strategy for replacing FRUs for CTO, CMV, and
GAV . . . . . . . . . . . . . . . .
Product definition . . . . . . . . . .
FRU identification for CTO, CMV, and GAV
products . . . . . . . . . . . . .
Important information about replacing RoHS
compliant FRUs . . . . . . . . . . . .
.
.
.
.
17
18
18
18
. 19
. 19
. 19
. 21
General checkout . . . . . . . . . . 23
What to do first . . . . . . . . .
Checkout guide . . . . . . . . .
Diagnostics using PC-Doctor for DOS
PC-Doctor for Windows . . . . .
Power system checkout . . . . . .
Checking the ac adapter . . . . .
Checking operational charging . . .
Checking the battery pack . . . .
Checking the backup battery . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
24
25
26
28
29
29
30
30
31
Related service information . . . . . . 33
Restoring the factory contents by using Product
Recovery discs . . . . . . . . . . .
Passwords . . . . . . . . . . . . .
Hard-disk password . . . . . . . .
Supervisor password . . . . . . . .
User password . . . . . . . . . .
Power-on password . . . . . . . .
How to remove the hard-disk password . .
How to remove the supervisor password .
How to remove the user password . . .
Power management . . . . . . . . .
Screen blank mode . . . . . . . . .
Standby mode . . . . . . . . . .
Hibernation mode . . . . . . . . .
Symptom-to-FRU index . . . . . . . .
© Copyright Lenovo 2008
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
33
34
34
35
35
35
35
36
36
37
37
37
38
39
Numeric error codes .
Error messages . . .
Beep symptoms . . .
No-beep symptoms . .
LCD-related symptoms
Intermittent problems .
Undetermined problems
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
39
41
42
42
43
44
44
IdeaPad S9e and S10e . . . . . . . . 45
Specifications . . . . . . . . . . . . . . 46
Status indicators . . . . . . . . . . . . . 47
FRU tests . . . . . . . . . . . . . . . 49
Fn key combinations . . . . . . . . . . . 50
FRU replacement notices . . . . . . . . . . 51
Screw notices . . . . . . . . . . . . . 51
Retaining serial numbers . . . . . . . . . 52
Removing and replacing a FRU . . . . . . . . 54
Before servicing IdeaPad S9e and S10e . . . . 55
1010 Battery pack . . . . . . . . . . . 56
1020 Hard disk drive (HDD) door . . . . . . 57
1030 Hard disk drive (HDD). . . . . . . . 58
1040 DIMM . . . . . . . . . . . . . 61
1050 Palm rest assembly . . . . . . . . . 62
1060 PCI Express Mini Card for wireless LAN . . 65
1070 Bluetooth daughter card and Bluetooth
cable . . . . . . . . . . . . . . . 67
1080 Keyboard . . . . . . . . . . . . 69
1090 Keyboard bezel . . . . . . . . . . 72
1100 fan assembly . . . . . . . . . . . 74
1110 System board and backup battery . . . . 78
1120 LCD assembly . . . . . . . . . . . 81
1130 Speaker and base cover assembly . . . . 83
2010 LCD front bezel . . . . . . . . . . 85
2020 Hinges . . . . . . . . . . . . . 86
2030 LCD panel and LCD cable . . . . . . 88
2040 Integrated camera, camera cable, and LCD
rear cover assembly . . . . . . . . . . 91
Locations . . . . . . . . . . . . . . . 93
Front view. . . . . . . . . . . . . . 93
Bottom view . . . . . . . . . . . . . 94
Parts list . . . . . . . . . . . . . . . 95
Overall . . . . . . . . . . . . . . . 96
LCD FRUs . . . . . . . . . . . . . 101
Keyboard . . . . . . . . . . . . . . 106
Miscellaneous parts . . . . . . . . . . 107
AC adapters . . . . . . . . . . . . . 108
Power cords . . . . . . . . . . . . . 109
Recovery discs . . . . . . . . . . . . 110
Common service tools . . . . . . . . . 114
Notices . . . . . . . . . . . . . . 115
Trademarks .
.
.
.
.
.
.
.
.
.
.
.
.
. 116
iii
iv
IdeaPad S9e and S10e Hardware Maintenance Manual
About this manual
This manual contains service and reference information for the following IdeaPad™
products.
IdeaPad S9e and S10e
MT 4068 and 4187
Use this manual along with the advanced diagnostic tests to troubleshoot
problems.
The manual is divided into sections as follows:
v The common sections provide general information, guidelines, and safety
information required in servicing computers.
v The product-specific section includes service, reference, and product-specific
parts information.
Important:
This manual is intended only for trained servicers who are familiar with IdeaPad
products. Use this manual along with the advanced diagnostic tests to
troubleshoot problems effectively.
Before servicing a IdeaPad product, be sure to read all the information under
“Safety information” on page 1 and “Important service information” on page 17.
© Copyright Lenovo 2008
v
vi
IdeaPad S9e and S10e Hardware Maintenance Manual
Safety information
This chapter presents following safety information that you need to be familiar
with before you service a IdeaPad computer.
v “General safety” on page 2
v “Electrical safety” on page 3
v “Safety inspection guide” on page 5
v “Handling devices that are sensitive to electrostatic discharge” on page 6
v “Grounding requirements” on page 6
v “Safety notices: multilingual translations” on page 7
v “Laser compliance statement” on page 14
© Copyright Lenovo 2008
1
General safety
Follow these rules to ensure general safety:
v Observe good housekeeping in the area of the machines during and after
maintenance.
v When lifting any heavy object:
1. Make sure that you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt to
lift.
4. Lift by standing or by pushing up with your leg muscles; this action removes
the strain from the muscles in your back. Do not attempt to lift any object that
weighs more than 16 kg (35 lb) or that you think is too heavy for you.
v Do not perform any action that causes hazards to the customer, or that makes
the equipment unsafe.
v Before you start the machine, make sure that other service representatives and
the customer’s personnel are not in a hazardous position.
v Place removed covers and other parts in a safe place, away from all personnel,
while you are servicing the machine.
v Keep your toolcase away from walk areas so that other people will not trip over
it.
v Do not wear loose clothing that can be trapped in the moving parts of a
machine. Make sure that your sleeves are fastened or rolled up above your
elbows. If your hair is long, fasten it.
v Insert the ends of your necktie or scarf inside clothing or fasten it with a
nonconductive clip, about 8 centimeters (3 inches) from the end.
v Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your
clothing.
Attention: Metal objects are good electrical conductors.
v Wear safety glasses when you are hammering, drilling, soldering, cutting wire,
attaching springs, using solvents, or working in any other conditions that might
be hazardous to your eyes.
v After service, reinstall all safety shields, guards, labels, and ground wires.
Replace any safety device that is worn or defective.
v Reinstall all covers correctly before returning the machine to the customer.
v Fan louvers on the machine help to prevent overheating of internal components.
Do not obstruct fan louvers or cover them with labels or stickers.
2
IdeaPad S9e and S10e Hardware Maintenance Manual
Electrical safety
Observe the following rules when working on electrical equipment.
Important:
Use only approved tools and test equipment. Some hand tools have handles
covered with a soft material that does not insulate you when working with live
electrical currents.
Many customers have, near their equipment, rubber floor mats that contain small
conductive fibers to decrease electrostatic discharges. Do not use this type of mat
to protect yourself from electrical shock.
v Find the room emergency power-off (EPO) switch, disconnecting switch, or
electrical outlet. If an electrical accident occurs, you can then operate the switch
or unplug the power cord quickly.
v Do not work alone under hazardous conditions or near equipment that has
hazardous voltages.
v Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing main units
v Before you start to work on the machine, unplug the power cord. If you cannot
unplug it, ask the customer to power-off the wall box that supplies power to the
machine, and to lock the wall box in the off position.
v If you need to work on a machine that has exposed electrical circuits, observe the
following precautions:
– Ensure that another person, familiar with the power-off controls, is near you.
Attention: Another person must be there to switch off the power, if
necessary.
– Use only one hand when working with powered-on electrical equipment;
keep the other hand in your pocket or behind your back.
Attention: An electrical shock can occur only when there is a complete
circuit. By observing the above rule, you may prevent a current from passing
through your body.
– When using testers, set the controls correctly and use the approved probe
leads and accessories for that tester.
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate you
from grounds such as metal floor strips and machine frames.
v
v
v
v
Observe the special safety precautions when you work with very high voltages;
Instructions for these precautions are in the safety sections of maintenance
information. Use extreme care when measuring high voltages.
Regularly inspect and maintain your electrical hand tools for safe operational
condition.
Do not use worn or broken tools and testers.
Never assume that power has been disconnected from a circuit. First, check that it
has been powered off.
Always look carefully for possible hazards in your work area. Examples of these
hazards are moist floors, nongrounded power extension cables, power surges,
and missing safety grounds.
Safety information
3
v Do not touch live electrical circuits with the reflective surface of a plastic dental
mirror. The surface is conductive; such touching can cause personal injury and
machine damage.
v Do not service the following parts with the power on when they are removed
from their normal operating places in a machine:
– Power supply units
– Pumps
– Blowers and fans
– Motor generators
and similar units. (This practice ensures correct grounding of the units.)
v If an electrical accident occurs:
– Use caution; do not become a victim yourself.
– Switch off power.
– Send another person to get medical aid.
4
IdeaPad S9e and S10e Hardware Maintenance Manual
Safety inspection guide
The purpose of this inspection guide is to assist you in identifying potentially
unsafe conditions. As each machine was designed and built, required safety items
were installed to protect users and service personnel from injury. This guide
addresses only those items. You should use good judgment to identify potential
safety hazards due to attachment of non-IdeaPad features or options not covered
by this inspection guide.
If any unsafe conditions are present, you must determine how serious the apparent
hazard could be and whether you can continue without first correcting the
problem.
Consider these conditions and the safety hazards they present:
v Electrical hazards, especially primary power (primary voltage on the frame can
cause serious or fatal electrical shock)
v Explosive hazards, such as a damaged CRT face or a bulging capacitor
v Mechanical hazards, such as loose or missing hardware
To determine whether there are any potentially unsafe conditions, use the
following checklist at the beginning of every service task. Begin the checks with
the power off, and the power cord disconnected.
Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Power off the computer. Disconnect the power cord.
3. Check the power cord for:
4.
5.
6.
7.
8.
9.
a. A third-wire ground connector in good condition. Use a meter to measure
third-wire ground continuity for 0.1 ohm or less between the external
ground pin and the frame ground.
b. The power cord should be the type specified in the parts list.
c. Insulation must not be frayed or worn.
Check for cracked or bulging batteries.
Remove the cover.
Check for any obvious non-IdeaPad alterations. Use good judgment as to the
safety of any non-IdeaPad alterations.
Check inside the unit for any obvious unsafe conditions, such as metal filings,
contamination, water or other liquids, or signs of fire or smoke damage.
Check for worn, frayed, or pinched cables.
Check that the power-supply cover fasteners (screws or rivets) have not been
removed or tampered with.
Safety information
5
Handling devices that are sensitive to electrostatic discharge
Any computer part containing transistors or integrated circuits (ICs) should be
considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when
there is a difference in charge between objects. Protect against ESD damage by
equalizing the charge so that the machine, the part, the work mat, and the person
handling the part are all at the same charge.
Notes:
1. Use product-specific ESD procedures when they exceed the requirements
noted here.
2. Make sure that the ESD protective devices you use have been certified (ISO
9000) as fully effective.
When handling ESD-sensitive parts:
v Keep the parts in protective packages until they are inserted into the product.
v Avoid contact with other people.
v Wear a grounded wrist strap against your skin to eliminate static on your body.
v Prevent the part from touching your clothing. Most clothing is insulative and
retains a charge even when you are wearing a wrist strap.
v Use the black side of a grounded work mat to provide a static-free work surface.
The mat is especially useful when handling ESD-sensitive devices.
v Select a grounding system, such as those listed below, to provide protection that
meets the specific service requirement.
Note:
The use of a grounding system to guard against ESD damage is desirable but not
necessary.
– Attach the ESD ground clip to any frame ground, ground braid, or green-wire
ground.
– When working on a double-insulated or battery-operated system, use an ESD
common ground or reference point. You can use coax or connector-outside
shells on these systems.
– Use the round ground prong of the ac plug on ac-operated computers.
Grounding requirements
Electrical grounding of the computer is required for operator safety and correct
system function. Proper grounding of the electrical outlet can be verified by a
certified electrician.
6
IdeaPad S9e and S10e Hardware Maintenance Manual
Safety notices: multilingual translations
The safety notices in this section are provided in English, French, German, Hebrew,
Italian, Japanese, and Spanish.
Safety notice 1
Before the computer is powered on after FRU replacement, make sure all screws,
springs, and other small parts are in place and are not left loose inside the
computer. Verify this by shaking the computer and listening for rattling sounds.
Metallic parts or metal flakes can cause electrical shorts.
Avant de remettre l’ordinateur sous tension après remplacement d’une unité en
clientèle, vérifiez que tous les ressorts, vis et autres pièces sont bien en place et
bien fixées. Pour ce faire, secouez l’unité et assurez-vous qu’aucun bruit suspect
ne se produit. Des pièces métalliques ou des copeaux de métal pourraient causer
un court-circuit.
Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird,
muß sichergestellt werden, daß keine Schrauben, Federn oder andere Kleinteile
fehlen oder im Gehäuse vergessen wurden. Der Computer muß geschüttelt und
auf Klappergeräusche geprüft werden. Metallteile oder-splitter können
Kurzschlüsse erzeugen.
Prima di accendere l’elaboratore dopo che é stata effettuata la sostituzione di una FRU,
accertarsi che tutte le viti, le molle e tutte le altri parti di piccole dimensioni siano nella
corretta posizione e non siano sparse all’interno dell’elaboratore. Verificare ciò scuotendo
l’elaboratore e prestando attenzione ad eventuali rumori; eventuali parti o pezzetti
metallici possono provocare cortocircuiti pericolosi.
Antes de encender el sistema despues de sustituir una FRU, compruebe que todos los
tornillos, muelles y demás piezas pequeñas se encuentran en su sitio y no se encuentran
sueltas dentro del sistema. Compruébelo agitando el sistema y escuchando los posibles
ruidos que provocarían. Las piezas metálicas pueden causar cortocircuitos eléctricos.
Safety information
7
Safety notice 2
DANGER
Some standby batteries contain a small amount of nickel and cadmium. Do not
disassemble a standby battery, recharge it, throw it into fire or water, or short-circuit it.
Dispose of the battery as required by local ordinances or regulations. Use only the
battery in the appropriate parts listing. Use of an incorrect battery can result in
ignition or explosion of the battery.
Certaines batteries de secours contiennent du nickel et du cadmium. Ne les démontez
pas, ne les rechargez pas, ne les exposez ni au feu ni à l’eau. Ne les mettez pas en
court-circuit. Pour les mettre au rebut, conformez-vous à la réglementation en vigueur.
Lorsque vous remplacez la pile de sauvegarde ou celle de l’horloge temps réel, veillez
à n’utiliser que les modèles cités dans la liste de pièces détachées adéquate. Une
batterie ou une pile inappropriée risque de prendre feu ou d’exploser.
Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet, kann
geringe Mengen Nickel und Cadmium enthalten. Sie darf nur durch die Verkaufsstelle
oder den IBM Kundendienst ausgetauscht werden. Sie darf nicht zerlegt,
wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden. Die
Batterie kann schwere Verbrennungen oder Verätzungen verursachen. Bei der
Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim Ersetzen der
Bereitschafts-oder Systembatterie nur Batterien des Typs verwenden, der in der
Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien kann zu Entzündung oder
Explosion führen.
Alcune batterie di riserva contengono una piccola quantità di nichel e cadmio. Non
smontarle, ricaricarle, gettarle nel fuoco o nell’acqua né cortocircuitarle. Smaltirle
secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni
locali). Quando si sostituisce la batteria dell’RTC (real time clock) o la batteria di
supporto, utilizzare soltanto i tipi inseriti nell’appropriato Catalogo parti. L’impiego di
una batteria non adatta potrebbe determinare l’incendio o l’esplosione della batteria
stessa.
Algunas baterías de reserva contienen una pequeña cantidad de níquel y cadmio. No
las desmonte, ni recargue, ni las eche al fuego o al agua ni las cortocircuite.
Deséchelas tal como dispone la normativa local. Utilice sólo baterías que se
encuentren en la lista de piezas. La utilización de una batería no apropiada puede
provocar la ignición o explosión de la misma.
8
IdeaPad S9e and S10e Hardware Maintenance Manual
Safety notice 3
DANGER
The battery pack contains small amounts of nickel. Do not disassemble it, throw it
into fire or water, or short-circuit it. Dispose of the battery pack as required by local
ordinances or regulations. Use only the battery in the appropriate parts listing when
replacing the battery pack. Use of an incorrect battery can result in ignition or
explosion of the battery.
La batterie contient du nickel. Ne la démontez pas, ne l’exposez ni au feu ni à l’eau.
Ne la mettez pas en court-circuit. Pour la mettre au rebut, conformez-vous à la
réglementation en vigueur. Lorsque vous remplacez la batterie, veillez à n’utiliser que
les modèles cités dans la liste de pièces détachées adéquate. En effet, une batterie
inappropriée risque de prendre feu ou d’exploser.
Akkus enthalten geringe Mengen von Nickel. Sie dürfen nicht zerlegt,
wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden. Bei
der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim Ersetzen
der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgeführt ist.
Der Einsatz falscher Batterien kann zu Entzündung oder Explosion führen.
La batteria contiene piccole quantità di nichel. Non smontarla, gettarla nel fuoco o
nell’acqua né cortocircuitarla. Smaltirla secondo la normativa in vigore (DPR 915/82,
successive disposizioni e disposizioni locali). Quando si sostituisce la batteria,
utilizzare soltanto i tipi inseriti nell’appropriato Catalogo parti. L’impiego di una
batteria non adatta potrebbe determinare l’incendio o l’esplosione della batteria stessa.
Las baterías contienen pequeñas cantidades de níquel. No las desmonte, ni recargue,
ni las eche al fuego o al agua ni las cortocircuite. Deséchelas tal como dispone la
normativa local. Utilice sólo baterías que se encuentren en la lista de piezas al
sustituir la batería. La utilización de una batería no apropiada puede provocar la
ignición o explosión de la misma.
Safety information
9
Safety notice 4
DANGER
The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it,
remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate
it, or expose its cell contents to water. Dispose of the battery as required by local
ordinances or regulations. Use only the battery in the appropriate parts listing. Use of
an incorrect battery can result in ignition or explosion of the battery.
La pile de sauvegarde contient du lithium. Elle présente des risques d’incendie,
d’explosion ou de brûlures graves. Ne la rechargez pas, ne retirez pas son connecteur
polarisé et ne la démontez pas. Ne l’exposez pas à une temperature supérieure à 100°C,
ne la faites pas brûler et n’en exposez pas le contenu à l’eau. Mettez la pile au rebut
conformément à la réglementation en vigueur. Une pile inappropriée risque de
prendre feu ou d’exploser.
Die Systembatterie ist eine Lithiumbatterie. Sie kann sich entzünden, explodieren
oder schwere Verbrennungen hervorrufen. Batterien dieses Typs dürfen nicht
aufgeladen, zerlegt, über 100 C erhitzt oder verbrannt werden. Auch darf ihr Inhalt
nicht mit Wasser in Verbindung gebracht oder der zur richtigen Polung angebrachte
Verbindungsstecker entfernt werden. Bei der Entsorgung die örtlichen Bestimmungen
für Sondermüll beachten. Beim Ersetzen der Batterie nur Batterien des Typs
verwenden, der in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien
kann zu Entzündung oder Explosion führen.
La batteria di supporto e una batteria al litio e puo incendiarsi, esplodere o procurare
gravi ustioni. Evitare di ricaricarla, smontarne il connettore polarizzato, smontarla,
riscaldarla ad una temperatura superiore ai 100 gradi centigradi, incendiarla o gettarla
in acqua. Smaltirla secondo la normativa in vigore (DPR 915/82, successive
disposizioni e disposizioni locali). L’impiego di una batteria non adatta potrebbe
determinare l’incendio o l’esplosione della batteria stessa.
La batería de repuesto es una batería de litio y puede provocar incendios, explosiones
o quemaduras graves. No la recargue, ni quite el conector polarizado, ni la desmonte,
ni caliente por encima de los 100°C (212°F), ni la incinere ni exponga el contenido de
sus celdas al agua. Deséchela tal como dispone la normativa local.
10
IdeaPad S9e and S10e Hardware Maintenance Manual
Safety notice 5
If the LCD breaks and the fluid from inside the LCD gets into your eyes or on
your hands, immediately wash the affected areas with water for at least 15
minutes. Seek medical care if any symptoms from the fluid are present after
washing.
Si le panneau d’affichage à cristaux liquides se brise et que vous recevez dans les
yeux ou sur les mains une partie du fluide, rincez-les abondamment pendant au
moins quinze minutes. Consultez un médecin si des symptômes persistent après
le lavage.
Die Leuchtstoffröhre im LCD-Bildschirm enthält Quecksilber. Bei der Entsorgung
die örtlichen Bestimmungen für Sondermüll beachten. Der LCD-Bildschirm
besteht aus Glas und kann zerbrechen, wenn er unsachgemäß behandelt wird
oder der Computer auf den Boden fällt. Wenn der Bildschirm beschädigt ist und
die darin befindliche Flüssigkeit in Kontakt mit Haut und Augen gerät, sollten
die betroffenen Stellen mindestens 15 Minuten mit Wasser abgespült und bei
Beschwerden anschließend ein Arzt aufgesucht werden.
Nel caso che caso l’LCD si dovesse rompere ed il liquido in esso contenuto entrasse in
contatto con gli occhi o le mani, lavare immediatamente le parti interessate con acqua
corrente per almeno 15 minuti; poi consultare un medico se i sintomi dovessero
permanere.
Si la LCD se rompe y el fluido de su interior entra en contacto con sus ojos o sus manos,
lave inmediatamente las áreas afectadas con agua durante 15 minutos como mínimo.
Obtenga atención medica si se presenta algún síntoma del fluido despues de lavarse.
Safety information
11
Safety notice 6
DANGER
To avoid shock, do not remove the plastic cover that protects the lower part of the
inverter card.
Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique
protégeant la partie inférieure de la carte d’alimentation.
Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der
Spannungswandlerplatine umgibt, nicht entfernen.
Per evitare scosse elettriche, non rimuovere la copertura in plastica che avvolge la
parte inferiore della scheda invertitore.
Para evitar descargas, no quite la cubierta de plástico que rodea la parte baja de la
tarjeta invertida.
Safety notice 7
DANGER
Though the main batteries have low voltage, a shorted or grounded battery can
produce enough current to burn personnel or combustible materials.
Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou la mise
à la masse d’une batterie peut produire suffisamment de courant pour brûler des
matériaux combustibles ou causer des brûlures corporelles graves.
Obwohl Hauptbatterien eine niedrige Spannung haben, können sie doch bei
Kurzschluß oder Erdung genug Strom abgeben, um brennbare Materialien zu
entzünden oder Verletzungen bei Personen hervorzurufen.
Sebbene le batterie di alimentazione siano a basso voltaggio, una batteria in corto
circuito o a massa può fornire corrente sufficiente da bruciare materiali combustibili o
provocare ustioni ai tecnici di manutenzione.
Aunque las baterías principales tienen un voltaje bajo, una batería cortocircuitada o
con contacto a tierra puede producir la corriente suficiente como para quemar material
combustible o provocar quemaduras en el personal.
12
IdeaPad S9e and S10e Hardware Maintenance Manual
Safety notice 8
DANGER
Before removing any FRU, power off the computer, unplug all power cords from
electrical outlets, remove the battery pack, and then disconnect any interconnecting
cables.
Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension,
débranchez tous les cordons d’alimentation des socles de prise de courant, retirez la
batterie et déconnectez tous les cordons d’interface.
Die Stromzufuhr muß abgeschaltet, alle Stromkabel aus der Steckdose gezogen, der
Akku entfernt und alle Verbindungskabel abgenommen sein, bevor eine FRU entfernt
wird.
Prima di rimuovere qualsiasi FRU, spegnere il sistema, scollegare dalle prese elettriche
tutti i cavi di alimentazione, rimuovere la batteria e poi scollegare i cavi di
interconnessione.
Antes de quitar una FRU, apague el sistema, desenchufe todos los cables de las tomas
de corriente eléctrica, quite la batería y, a continuación, desconecte cualquier cable de
conexión entre dispositivos.
Safety information
13
Laser compliance statement
Some models of IdeaPad computer are equipped from the factory with an optical
storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are
also sold separately as options. If one of these drives is installed, it is certified in
the U.S. to conform to the requirements of the Department of Health and Human
Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class 1
laser products. Elsewhere, the drive is certified to conform to the requirements of
the International Electrotechnical Commission (IEC) 825 and CENELEC EN 60 825
for Class 1 laser products.
If a CD-ROM drive, a DVD-ROM drive, or another laser device is installed, note
the following:
CAUTION:
Use of controls or adjustments or performance of procedures other than those
specified herein might result in hazardous radiation exposure.
O uso de controles, ajustes ou desempenho de procedimentos diferentes daqueles aqui
especificados pode resultar em perigosa exposição à radiação.
Pour éviter tout risque d’exposition au rayon laser, respectez les consignes de réglage
et d’utilisation des commandes, ainsi que les procédures décrites.
Werden Steuer- und Einstellelemente anders als hier festgesetzt verwendet, kann
gefährliche Laserstrahlung auftreten.
L’utilizzo di controlli, regolazioni o l’esecuzione di procedure diverse da quelle
specificate possono provocare l’esposizione a.
El uso de controles o ajustes o la ejecución de procedimientos distintos de los aquí
especificados puede provocar la exposición a radiaciones peligrosas.
Opening the CD-ROM drive, the DVD-ROM drive, or any other optical storage
device could result in exposure to hazardous laser radiation. There are no
serviceable parts inside those drives. Do not open.
14
IdeaPad S9e and S10e Hardware Maintenance Manual
A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may
contain an embedded Class 3A or Class 3B laser diode. Note the following:
DANGER
Emits visible and invisible laser radiation when open. Do not stare into the beam, do
not view directly with optical instruments, and avoid direct exposure to the beam.
Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe diretamente
por meio de instrumentos óticos e evite exposição direta com o feixe de luz.
Rayonnement laser si carter ouvert. Évitez de fixer le faisceau, de le regarder
directement avec des instruments optiques, ou de vous exposer au rayon.
Laserstrahlung bei geöffnetem Gerät. Nicht direkt oder über optische Instrumente in
den Laserstrahl sehen und den Strahlungsbereich meiden.
Kinyitáskor lézersugár ! Ne nézzen bele se szabad szemmel, se optikai eszközökkel.
Kerülje a sugárnyalábbal való érintkezést !.
Aprendo l’unità vengono emesse radiazioni laser. Non fissare il fascio, non guardarlo
direttamente con strumenti ottici e evitare l’esposizione diretta al fascio.
Radiación láser al abrir. No mire fijamente ni examine con instrumental óptico el haz
de luz. Evite la exposición directa al haz.
Safety information
15
16
IdeaPad S9e and S10e Hardware Maintenance Manual
Important service information
This chapter presents following important service information:
v “Strategy for replacing FRUs”
– “Strategy for replacing a hard disk drive” on page 18
– “Important notice for replacing a system board” on page 18
– “How to use error message” on page 18
v “Strategy for replacing FRUs for CTO, CMV, and GAV” on page 19
– “Product definition” on page 19
– “FRU identification for CTO, CMV, and GAV products” on page 19
v “Important information about replacing RoHS compliant FRUs” on page 21
Important:
BIOS and device driver fixes are customer-installable. The BIOS and device
drivers are posted on the customer support site http://www.lenovo.com/support
System Disassembly/Reassembly videos that show the FRU removals or
replacements for the Lenovo® authorized service technicians are available in the
following support site: http://www.lenovoservicetraining.com/ion/
Advise customers to contact the Customer Support Center at 800-426-7378 if they
need assistance in obtaining or installing any software fixes, drivers, and BIOS
downloads.
Customers in Canada should call the Customer Support Center at 800-565-3344
for assistance or download information.
Strategy for replacing FRUs
Before replacing parts:
Make sure that all software fixes, drivers, and BIOS downloads are installed
before replacing any FRUs listed in this manual.
After a system board is replaced, ensure that the latest BIOS is loaded to the
system board before completing the service action.
To download software fixes, drivers, and BIOS, do as follows:
1. Go to http://www.lenovo.com/support
2. Enter the product number of the computer or press Auto-detect button on the
screen.
3. Select Downloads and drivers.
4. Follow the directions on the screen and install the necessary software.
Use the following strategy to prevent unnecessary expense for replacing and
servicing FRUs:
© Copyright Lenovo 2008
17
v If you are instructed to replace a FRU but the replacement does not correct the
problem, reinstall the original FRU before you continue.
v Some computers have both a processor board and a system board. If you are
instructed to replace either the processor board or the system board, and
replacing one of them does not correct the problem, reinstall that board, and
then replace the other one.
v If an adapter or a device consists of more than one FRU, any of the FRUs may
be the cause of the error. Before replacing the adapter or device, remove the
FRUs, one by one, to see if the symptoms change. Replace only the FRU that
changed the symptoms.
Attention: The setup configuration on the computer you are servicing may have
been customized. Running Automatic Configuration may alter the settings. Note
the current configuration settings (using the View Configuration option); then,
when service has been completed, verify that those settings remain in effect.
Strategy for replacing a hard disk drive
Always try to run a low-level format before replacing a hard disk drive. This will
cause all customer data on the hard disk to be lost. Be sure that the customer has a
current backup of the data before doing this task.
Attention: The drive startup sequence in the computer you are servicing may
have been changed. Be extremely careful during write operations such as copying,
saving, or formatting. If you select an incorrect drive, data or programs can be
overwritten.
Important notice for replacing a system board
Some components mounted on a system board are very sensitive. Improper
handling of a system board can cause damage to those components, and may
cause a system malfunction.
Attention: When handling a system board:
v Do not drop a system board or apply any excessive force to it.
v Avoid rough handling of any kind.
v Avoid bending a system board and hard pushing to prevent cracking at each
BGA (Ball Grid Array) chipset.
How to use error message
Use the error codes displayed on the screen to diagnose failures. If more than one
error code is displayed, begin the diagnosis with the first error code. Whatever
causes the first error code may also cause false error codes. If no error code is
displayed, see whether the error symptom is listed in the Symptom-to-FRU Index
for the computer you are servicing.
18
IdeaPad S9e and S10e Hardware Maintenance Manual
Strategy for replacing FRUs for CTO, CMV, and GAV
Product definition
Dynamic Configure To Order (CTO)
This provides the ability for a customer to configure an IBM® or a Lenovo solution
from an eSite, and have this configuration sent to fulfillment, where it is built and
shipped directly to the customer. The machine label, Product Entitlement
Warehouse (PEW), eSupport, and the HMM will load these products as the 4-digit
MT and 3-digit model, where model = “CTO” (Example: 1829-CTO).
Custom Model Variant (CMV)
This is a unique configuration that has been negotiated between IBM or Lenovo
and the customer. A unique 4-digit MT and 3-digit model is provided to the
customer to place orders (Example: 1829-W15). A CMV is a special bid offering.
Therefore, it is NOT generally announced.
v The MTM portion of the machine label is the 4-digit MT and 3-digit model,
where model = “CTO” (Example: 1829-CTO). The PRODUCT ID portion of the
machine label is the 4-digit MT and 3-digit CMV model (Example: 1829-W15).
v The PEW record is the 4-digit MT and 3-digit model, where model = “CTO”
(Example: 1829-CTO).
v eSupport will show both the CTO and CMV machine type models (Example:
1829-CTO and 1829-W15 will be found on the eSupport site.)
v The HMM will have the 4-digit MT and 3-digit CTO model only (Example:
1829-CTO). Again, CMVs are custom models and are not found in the HMM.
General Announce Variant (GAV)
This is a standard model (fixed configuration). GAVs are announced and offered to
all customers. The MTM portion of the machine label is a 4-digit MT and 3-digit
model, where model = a “fixed part number”, not “CTO” (Example: 1829-F1U).
Also, PEW, eSupport, and the HMM will list these products under the same fixed
model number.
FRU identification for CTO, CMV, and GAV products
There are three information resources to identify which FRUs are used to support
CTO, CMV, and GAV products. These sources are PEW, eSupport, and the HMM.
Using PEW
v PEW is the primary source for identifying FRU part numbers and FRU
descriptions for the key commodities for CTO, CMV and GAV products at a MT
- serial number level. An example of key commodities are hard disk drives,
system boards, microprocessors, Liquid Crystal Displays (LCDs), and memory.
v Remember, all CTO and CMV products are loaded in PEW under the 4-digit MT
and 3-digit model, where model = “CTO” (Example: 1829-CTO). GAVs are
loaded in PEW under the 4-digit MT and 3-digit model, where model = a “fixed
part number”, not “CTO” (Example: 1829-F1U).
v PEW can be accessed at the following Web site: http://w3-01.ibm.com/pc/
entitle/pg2/Service.wss/display/Home
Customers can also access PEW via
http://www-307.ibm.com/pc/support/site.wss/product.do?template=/warranty/
Important service information
19
warranty.vm&sitestyle=lenovo
Select Warranty lookup. Input the MT and the Serial number and the list of key
commodities will be returned in the PEW record under COMPONENT
INFORMATION.
v Business Partners using Eclaim will access PEW when performing Entitlement
Lookup. Business Partners will enter Loc ID, MT and Serial, and the key
commodities will be returned in the Eclaim record under SYSTEM DETAILS.
v Authorized IBM Business Partners can access Eclaim at the following Web site:
https://wca.eclaim.com
Using eSupport
For Key Commodities (Examples - hard disk drive, system board,
microprocessor, LCD, and memory)
v eSupport can be used to view the list of key commodities built in a particular
machine serial (this is the same record found in PEW).
v eSupport can be accessed at the following Web site: http://www.lenovo.com/
support
v To view the key commodities, click on PARTS INFORMATION, then PARTS
LOOKUP. Type in the model type and serial number. The key commodities will
be returned in the eSupport record under PARTS SHIPPED WITH YOUR
SYSTEM.
For the Remaining FRUs (the complete list of FRUs at the MT Model level)
v eSupport can be used to view the complete list of FRUs for a machine type and
model.
v To view the complete list of FRUs, type in the machine type and model
(Example: 1829-CTO) under QUICK PATH. Under “View by Document Type”
select PARTS INFORMATION. Under “Filter by Category” select SERVICE
PARTS. Under “Parts Information by Date” select SYSTEM SERVICE PARTS. The
list of service parts by description, with applicable machine type model and FRU
will be displayed.
Using the HMM
For Key Commodities (Examples - hard disk drive, system board,
microprocessor, LCD, and memory)
Use the HMM as a back-up to PEW and eSupport to view the complete list of
FRUs at the MT Model level.
20
IdeaPad S9e and S10e Hardware Maintenance Manual
Important information about replacing RoHS compliant FRUs
RoHS, The Restriction of Hazardous Substances in Electrical and Electronic
Equipment Directive (2002/95/EC) is a European Union legal requirement
affecting the global electronics industry. RoHS requirements must be
implemented on Lenovo products placed on the market after June 2006. Products
on the market before June 2006 are not required to have RoHS compliant parts.
If the original FRU parts are non compliant, replacement parts can also be non
compliant. In all cases if the original FRU parts are RoHS compliant, the
replacement part must also be RoHS compliant.
Note: RoHS and non-RoHS FRU part numbers with the same fit and function are
identified with unique FRU part numbers.
Lenovo plans to transition to RoHS compliance well before the implementation
date and expects its suppliers to be ready to support Lenovo’s requirements and
schedule in the EU. Products sold in 2005 and 2006, will contain some RoHS
compliant FRUs. The following statement pertains to these products and any
product Lenovo produces containing RoHS compliant FRUs.
RoHS compliant FRUs have unique FRU part numbers. Before or after the RoHS
implementation date, failed RoHS compliant parts must always be replaced using
RoHS compliant FRUs, so only the FRUs identified as compliant in the system
HMM or direct substitutions for those FRUs may be used.
Products marketed before June 2006
Products marketed after June 2006
Current or original
part
Replacement FRU
Current or original
part
Replacement FRU
Non-RoHS
Can be Non-RoHS
Must be RoHS
Must be RoHS
Non-RoHS
Can be RoHS
Non-RoHS
Can sub to RoHS
RoHS
Must be RoHS
Note: A direct substitution is a part with a different FRU part number that is
automatically shipped by the distribution center at the time of the order.
Important service information
21
22
IdeaPad S9e and S10e Hardware Maintenance Manual
General checkout
This chapter presents following information:
v “What to do first” on page 24
v “Checkout guide” on page 25
– “Diagnostics using PC-Doctor for DOS” on page 26
– “PC-Doctor for Windows” on page 28
v “Power system checkout” on page 29
The descriptions in this chapter apply to any IdeaPad model that supports the
PC-Doctor® for DOS diagnostics program. Some descriptions might not apply to
your particular computer.
Before you go to the checkout guide, be sure to read the following important notes.
Important notes:
v Only certified trained personnel should service the computer.
v Before replacing any FRU, read the entire page on removing and replacing
FRUs.
v When you replace FRUs, use new nylon-coated screws.
v Be extremely careful during such write operations as copying, saving, or
formatting. Drives in the computer that you are servicing sequence might
have been altered. If you select an incorrect drive, data or programs might be
overwritten.
v Replace a FRU only with another FRU of the correct model. When you
replace a FRU, make sure that the model of the machine and the FRU part
number are correct by referring to the FRU parts list.
v A FRU should not be replaced because of a single, unreproducible failure.
Single failures can occur for a variety of reasons that have nothing to do with
a hardware defect, such as cosmic radiation, electrostatic discharge, or
software errors. Consider replacing a FRU only when a problem recurs. If you
suspect that a FRU is defective, clear the error log and run the test again. If
the error does not recur, do not replace the FRU.
v Be careful not to replace a nondefective FRU.
© Copyright Lenovo 2008
23
What to do first
When you do return a FRU, you must include the following information in the
parts exchange form or parts return form that you attach to it:
__ 1. Name and phone number of servicer
__ 2. Date of service
__ 3. Date on which the machine failed
__ 4. Date of purchase
__ 5. Failure symptoms, error codes appearing on the display, and beep
symptoms
__ 6. Procedure index and page number in which the failing FRU was detected
__ 7. Failing FRU name and part number
__ 8. Machine type, model number, and serial number
__ 9. Customer’s name and address
Note for warranty: During the warranty period, the customer may be responsible
for repair costs if the computer damage was caused by misuse, accident,
modification, unsuitable physical or operating environment, or improper
maintenance by the customer.
Following is a list of some common items that are not covered under warranty and
some symptoms that might indicate that the system was subjected to stress beyond
normal use.
Before checking problems with the computer, determine whether the damage is
covered under the warranty by referring to the following list:
The following are not covered under warranty:
v LCD panel cracked from the application of excessive force or from being
dropped
v Scratched (cosmetic) parts
v Distortion, deformation, or discoloration of the cosmetic parts
v Plastic parts, latches, pins, or connectors that have been cracked or broken by
excessive force
v Damage caused by liquid spilled into the system
v Damage caused by the improper insertion of a PC Card or the installation of an
incompatible card
v Improper disc insertion or use of an optical drive
v Diskette drive damage caused by pressure on the diskette drive cover, foreign
material in the drive, or the insertion of a diskette with multiple labels
v Damaged or bent diskette eject button
v Fuses blown by attachment of a nonsupported device
v Forgotten computer password (making the computer unusable)
v Sticky keys caused by spilling a liquid onto the keyboard
v Use of an incorrect ac adapter on laptop products
The following symptoms might indicate damage caused by nonwarranted
activities:
v Missing parts might be a symptom of unauthorized service or modification.
v If the spindle of a hard disk drive becomes noisy, it may have been subjected to
excessive force, or dropped.
24
IdeaPad S9e and S10e Hardware Maintenance Manual
Checkout guide
Use the following procedures as a guide in identifying and correcting problems
with the IdeaPad computer.
Note: The diagnostic tests are intended to test only IdeaPad products. The use of
non-IdeaPad products, prototype cards, or modified options can lead to false
indications of errors and invalid system responses.
1. Identify the failing symptoms in as much detail as possible.
2. Verify the symptoms. Try to re-create the failure by running the diagnostic test
or by repeating the operation.
General checkout
25
Diagnostics using PC-Doctor for DOS
The IdeaPad computer has a test program called PC-Doctor for DOS (hereafter
called PC-Doctor.) You can detect errors by running the diagnostics test included in
PC-Doctor. This section is an overview of the procedure. For details that depend
on model-unique functions, refer to “IdeaPad S9e and S10e” on page 45.
Note:
PC-Doctor for DOS is available at following Web site: http://www.lenovo.com/
support
To create the PC-Doctor diagnostic CD or DVD, follow the instruction on the
Web site.
For some possible configurations of the computer, PC-Doctor might not run
correctly. To avoid this problem, you need to initialize the computer setup by use
of the BIOS Setup Utility before you run PC-Doctor.
To enter the BIOS Setup Utility, do as follows:
1. Turn on the computer.
2. When the Lenovo logo comes up, immediately press F2 to enter the BIOS Setup
Utility.
Note: If the customer has set a supervisor password, the BIOS Setup Utility menu
appears after the password is entered. If the customer has set a user password, you
can start the utility by entering that password; however, you cannot change all of
the parameters.
On the BIOS Setup Utility screen, press F9, Enter, F10, and then Enter.
Note: When you initialize the computer configuration, some devices are disabled,
such as the serial port. If you test one of these devices, you will need to enable it
by using Configuration utility for DOS. The utility is available on the following
Web site: http://www.lenovo.com/support
Testing the computer
To run the test, do as follows:
1. Insert the PC-Doctor disc into the optical drive; then power on the computer.
If the computer cannot be powered on, go to “Power system checkout” on page
29, and check the power sources.
If an error code appears, go to “Symptom-to-FRU index” on page 39.
On the first screen, select the model and press Enter. Follow the instructions on
the screen.
2. The main panel of PC-Doctor appears.
3. Select Diagnostics with the arrow keys, and press Enter.
A pull-down menu appears. (Its exact form depends on the model.)
Note: PC-Doctor menu does not mean the formal support device list. Some
unsupported device names may appear in the PC-Doctor menu.
26
IdeaPad S9e and S10e Hardware Maintenance Manual
Diagnostics
Interactive Tests
Hardware Info
Utility
Quit
F1=Help
Run Normal Test
Run Quick Test
CPU/Coprocessor
Systemboard
Video Adapter
Fixed Disks
Diskette Drives
Other Devices
PM Memory
PC-DOCTOR 2.0 Copyright 2002 PC-Doctor, Inc. All Rights Reserved.
Use the cursor keys and ESC to move in menus. Press ENTER to select.
The options on the test menu are as follows:
Diagnostics
v
v
v
v
v
v
v
v
v
Run Normal Test
Run Quick Test
CPU/Coprocessor
Systemboard
Video Adapter
Fixed Disks
Diskette Drives
Other Devices
PM Memory
Interactive Tests
v
v
v
v
v
v
Keyboard
Video
Mouse
Diskette
System Load
Optical Drive Test
Notes:
v In the Keyboard test in Interactive Tests, the Fn key should be held down for
at least 2 seconds; otherwise, it cannot be sensed.
v Video Adapter test supports only the LCD display on the IdeaPad computer. If
you have an external monitor attached to your computer, detach it before
running PC-Doctor for DOS.
4. Run the applicable function test.
5. Follow the instructions on the screen. If there is a problem, PC-Doctor shows
messages describing it.
6. To exit the test, select Quit — Exit Diag.
To cancel the test, press Esc.
Note: After running PC-Doctor, check the time and date on the system and reset
them if they are incorrect.
Detecting system information with PC-Doctor
PC-Doctor can detect the following system information:
Hardware Info
v System Configuration
v Memory Contents
v Physical Disk Drives
v Logical Disk Drives
v VGA Information
v IDE Drive Info
General checkout
27
v
v
v
v
v
PCI Information
PNPISA Info
SMBIOS Info
VESA LCD Info
Hardware Events Log
v
v
v
v
v
v
v
v
v
v
v
Run External Tests
Surface Scan Hard Disk
Benchmark System
DOS Shell
Tech Support Form
Battery Rundown
View Test Log
Print Log
Save Log
Full Erase Hard Drive
Quick Erase Hard Drive
Utility
PC-Doctor for Windows
This product is designed to help you troubleshoot and resolve problems related to
your computer. Select one of the categories listed below to display symptoms and
solutions:
v Check System Health
v System and Device Tests
v Lenovo Troubleshooting Center
v System Reports
v Updates and Support
28
IdeaPad S9e and S10e Hardware Maintenance Manual
Power system checkout
To
1.
2.
3.
4.
5.
6.
7.
verify a symptom, do the following:
Turn off the computer.
Remove the battery pack.
Connect the ac adapter.
Check that power is supplied when you turn on the computer.
Turn off the computer.
Disconnect the ac adapter and install the charged battery pack.
Check that the battery pack supplies power when you turn on the computer.
If you suspect a power problem, see the appropriate one of the following power
supply checkouts:
v “Checking the ac adapter”
v “Checking operational charging” on page 30
v “Checking the battery pack” on page 30
v “Checking the backup battery” on page 31
Checking the ac adapter
You are here because the computer fails only when the ac adapter is used.
v If the power-on indicator does not turn on, check the power cord of the ac
adapter for correct continuity and installation.
v If the computer does not charge during operation, go to “Checking operational
charging” on page 30
To check the ac adapter, do the following:
1. Unplug the ac adapter cable from the computer.
2. Measure the output voltage at the plug of the ac adapter cable. See the
following figure:
3
2
(20V)
Pin
Voltage (V dc)
1
+20
2
0
3
Ground
1
Note: Output voltage of pin no.2 of the ac adapter may different from the one
you are servicing.
3. If the voltage is not correct, replace the ac adapter.
4. If the voltage is acceptable, do the following:
v Replace the system board.
v If the problem persists, go to “IdeaPad S9e and S10e” on page 45.
Note: Noise from the ac adapter does not always indicate a defect.
General checkout
29
Checking operational charging
To check whether the battery charges properly during operation, use a discharged
battery pack or a battery pack that has less than 50% of the total power remaining
when installed in the computer.
Perform operational charging. If the battery status indicator or icon does not turn
on, remove the battery pack and let it return to room temperature. Reinstall the
battery pack. If the charge indicator or icon still does not turn on, replace the
battery pack.
If the charge indicator still does not turn on, replace the system board. Then
reinstall the battery pack. If it is still not charged, go to the next section.
Checking the battery pack
Battery charging does not start until the Power Meter shows that less than 95% of
the total power remains; under this condition the battery pack can charge to 100%
of its capacity. This protects the battery pack from being overcharged or from
having a shortened life.
To check your battery, move your cursor to the Power Meter icon in the icon tray
of the Windows® taskbar and wait for a moment (but do not click), and the
percentage of battery power remaining is displayed. To get detailed information
about the battery, double-click the Power Meter icon.
Note: If the battery pack becomes hot, it may not be able to charge. Remove it
from the computer and leave it at room temperature for a while. After it cools
down, reinstall and recharge it.
To check the battery pack, do the following:
1. Power off the computer.
2. Remove the battery pack and measure the voltage between battery terminals 1
(+) and 7 (-). See the following figure:
1(+)
2(+)
5
3 4
6(-)
7(-)
Terminal
Voltage (V dc)
1
+ 0 to + 12.6
7
Ground (-)
3. If the voltage is less than +11.0 V dc, the battery pack has been discharged.
Note: Recharging will take at least 3 hours, even if the indicator does not turn
on.
If the voltage is still less than +11.0 V dc after recharging, replace the battery.
4. If the voltage is more than +11.0 V dc, measure the resistance between battery
terminals 5 and 7. The resistance must be 4 to 30 K .
If the resistance is not correct, replace the battery pack. If the resistance is
correct, replace the system board.
30
IdeaPad S9e and S10e Hardware Maintenance Manual
Checking the backup battery
Do the following:
1. Power off the computer, and unplug the ac adapter from it.
2. Turn the computer upside down.
3. Remove the battery pack (see “1010 Battery pack” on page 56).
4. Remove the backup battery (see “1110 System board and backup battery” on
page 78).
5. Measure the voltage of the backup battery. See the following figure.
Red (+)
Black (-)
Wire
Voltage (V dc)
Red
+2.5 to +3.2
Black
Ground
v If the voltage is correct, replace the system board.
v If the voltage is not correct, replace the backup battery.
v If the backup battery discharges quickly after replacement, replace the system
board.
General checkout
31
32
IdeaPad S9e and S10e Hardware Maintenance Manual
Related service information
This chapter presents following information:
v “Restoring the factory contents by using Product Recovery discs”
v “Passwords” on page 34
v “Power management” on page 37
v “Symptom-to-FRU index” on page 39
Service Web site:
When the latest maintenance utility and the system program service diskette
become available, they will be posted on http://www.lenovo.com/spm
Restoring the factory contents by using Product Recovery discs
When the hard disk drive (HDD) or system board with a solid state drive (SSD) is
replaced because of a failure, no Product Recovery program is on the new drive. In
this case, you must use the recovery discs for the computer. Order the recovery
discs and the hard disk drive or system board with a solid state drive at the same
time so that you can recover the new drive with the pre-installed software when
they arrive. For information on which discs to order, see “Recovery discs” on page
110.
To install the factory contents by using Product Recovery discs, do the following:
Note: Recovery takes several hours. The length of time depends on the method
you use. If you use recovery discs, recovery takes at least five hours.
Windows XP Home Edition:
1. Insert the bootable disc.
2. Reboot the computer.
3. When the Lenovo logo comes up, press F12 to enter the Boot Menu.
4. To boot from the optical drive, select the optical drive, and then press Enter.
5. Select your language, and click Next.
6. Read the license. If you agree to the terms, select I accept these terms and
conditions and click Next.
7. Click Next to begin the recovery precess.
8. When prompted, insert the Product Recovery Disc and click OK.
9. When all of the data has been copied from the Product Recovery Disc, the
computer will restart automatically.
Note: The remainder of the recovery process is fully automated; no action is
required by you. The computer will restart into the Windows desktop several
times, and you might experience periods when no activity is apparent on the
screen for several minutes at a time. This is normal.
© Copyright Lenovo 2008
33
10. When the recovery process is complete, the Welcome to Microsoft Windows
screen is displayed. Follow the instructions on the screen to complete the
Windows setup.
SUSE Linux Enterprise Desktop 10:
1. Insert the bootable disc.
2. Reboot the computer.
3. When the Lenovo logo comes up, press F12 to enter the Boot Menu.
4. To boot from the optical drive, select the optical drive, and then press Enter.
5. To begin the recovery process, select Restore System.
6. A box pops up that says, “Think again... This will destroy ALL data on your
computer. There is no way back. Please save everything you might need before
you continue! Are you really sure? OK/Cancel.” Click OK.
7. A black screen appears, with messages showing that system data is being
written and then that data is being verified.
8. When the recovery process is complete, you will be prompted to remove the
disc and press a key to reboot the computer. Follow the instructions on the
screen.
Passwords
As many as three passwords may be needed for any IdeaPad computer: the
hard-disk password (HDP), the supervisor password (SVP), and the user password.
If any of these passwords has been set, a prompt for it appears on the screen
whenever the computer is turned on. The computer does not start until the
password is entered.
Exception: If only an SVP and a user password are installed, and Password on
boot is set to Disabled, the password prompt does not appear when the operating
system is booted.
Hard-disk password
Note: Computers with the solid state drive (SSD) do not support the hard-disk
password.
There are two hard-disk passwords (HDPs):
v User HDP—for the user
v Master HDP—for the system administrator, who can use it to get access to the
hard disk even if the user has changed the user HDP
Note: The Master + User mode requires two HDPs; the system administrator
enters both in the same operation. The system administrator then provides the user
HDP to the system user.
Attention: If the user HDP has been forgotten, check whether the master HDP is
available. If it is, it can be used for access to the hard disk drive. If no master HDP
is available, neither Lenovo nor Lenovo authorized servicers provide any services
to reset either the user or the master HDP, or to recover data from the hard disk
drive. The hard disk drive can be replaced, for a scheduled fee.
34
IdeaPad S9e and S10e Hardware Maintenance Manual
For how to remove the HDP, see “How to remove the hard-disk password.”
Supervisor password
A supervisor password (SVP) protects the system information stored in the BIOS
Setup Utility. The user enters the SVP to get access to the BIOS Setup Utility and
change the system configuration. It also can be used as a power-on password
(POP), if Password on boot is set to Enabled.
For how to remove the SVP, see “How to remove the supervisor password” on
page 36.
User password
If a user password has been set and Password on boot is set to Enabled, a
password prompt appears on the screen whenever the computer is turned on. The
user password is also used to enter the BIOS Setup Utility, but only a part of the
options can be set. The user password can be set only when the SVP has been set.
For how to remove the user password, see “How to remove the user password” on
page 36.
Power-on password
A power-on password (POP) protects the system from being powered on by an
unauthorized person. The password must be entered before an operating system
can be booted. The SVP and the user password can be used as the POP, if
Password on boot is set to Enabled.
How to remove the hard-disk password
Attention: If the user HDP has been forgotten and the master HDP cannot be
made available to the servicer, neither Lenovo nor Lenovo authorized servicers
provide any services to reset the user HDPs or to recover data from the hard disk
drive. The hard disk drive can be replaced, for a scheduled fee.
To remove a user HDP that has been forgotten, when the SVP and the master HDP
are known, do the following:
1. Turn on the computer.
2. When the Lenovo logo comes up, immediately press F2 to enter the BIOS
Setup Utility.
3. Enter the master HDP.
4. Select Security, using the cursor directional keys to move down the menu.
5. Select Set Hard Disk Passwords.
6. Select Change Master Password.
7. Type the current master HDP in the Enter Current Password field. then leave
the Enter New Password field blank, and press Enter twice.
8. In the Changes have been saved window, press Enter.
9. Press F10.
10. Select Yes in the Setup Configuration window.
Both user HDP and master HDP will have been removed.
Related service information
35
How to remove the supervisor password
To remove an SVP, do the following:
(A) If an SVP is know to the servicer:
1. Turn on the computer.
2. When the Lenovo logo comes up, immediately press F2 to enter the BIOS Setup
Utility.
3. If Password on boot is set to Enabled, enter the SVP.
4. Select Security, using the cursor directional keys to move down the menu.
5. Select Set Supervisor Password.
6. Type the current SVP in the Enter Current Password field. Then leave the Enter
New Password field blank, and press Enter twice.
7. In the Changes have been saved window, press Enter.
8. Press F10; then, in the Setup confirmation window, select Yes .
Both the SVP and the user password will be removed.
(B)
1.
2.
3.
If an SVP has been forgotten:
Turn on the computer.
Unplug the AC adapter cable from the computer.
Remove the battery pack.
For how to remove the battery pack, see “1010 Battery pack” on page 56.
4. Remove the backup battery.
For how to remove the backup battery, see “1110 System board and backup
battery” on page 78.
5. Wait about one minute.
6. Reinstall the backup battery and the battery pack.
Both the SVP and the user password will be removed.
How to remove the user password
To remove a user password that is known to the servicer, do the following:
1. Turn on the computer.
2. When the Lenovo logo comes up, immediately press F2 to enter the BIOS Setup
Utility.
3. If Password on boot is set to Enabled, enter the user password.
4. Select Security, using the cursor directional keys to move down the menu.
5. Select Set User Password.
6. Type the current user password in the Enter Current Password field. Then
leave the Enter New Password field blank, and press Enter twice.
7. In the Changes have been saved window, press Enter.
8. Press F10; then, in the Setup confirmation window, select Yes .
To remove a user password that has been forgotten, when the SVP is known, see
“How to remove the supervisor password”
36
IdeaPad S9e and S10e Hardware Maintenance Manual
Power management
To reduce power consumption, the computer has three power management modes:
screen blank, standby, and hibernation.
Screen blank mode
To enter screen blank mode, press Fn + F2. To end screen blank mode and resume
normal operation, press Fn + F2.
In certain circumstances, the computer goes into screen blank mode automatically:
v If the time set on the “Turn off monitor” timer in the operating system expires,
the LCD backlight turns off.
To end screen blank mode and resume normal operation, press any key.
Standby mode
When the computer enters standby mode, the following events occur in addition to
what occurs in screen blank mode:
v The LCD is powered off.
v The hard disk drive is powered off.
v The CPU stops.
To enter standby mode, press Fn+F1.
Note: If you are using the ACPI operating system, you can change the action of
Fn+F1.
In certain circumstances, the computer goes into standby mode automatically:
v If a “suspend time” has been set on the timer, and the user does not do any
operation with the keyboard, the touch panel, the hard disk, the parallel
connector, or the optical drive within that time.
v If the battery indicator blinks orange, indicating that the battery power is low.
(Alternatively, if Hibernate when battery becomes low has been selected in the
“Power Management Properties” window, the computer goes into hibernation
mode.)
Note for the APM operating system: Even if you do not set the low-battery alarm,
the charge indicator notifies you when the battery is low, and then the computer
enters the power-saving mode automatically. This default low-battery behavior is
independent of the operating system; so if you have set the low-battery alarm, the
computer may not do what you specified. It chooses either your setting or the
default setting, whichever is appropriate.
If you are using the ACPI operating system, only the low-battery alarm is
available.
To cause the computer to return from standby mode and resume operation, do one
of the following:
v Press the Fn key.
v Open the LCD cover.
v Turn on the power switch.
Related service information
37
Also, in either of the following events, the computer automatically returns from
standby mode and resumes operation:
v The ring indicator (RI) is signaled by a serial device or a PC Card device.
v The time set on the resume timer elapses.
Note: The computer does not accept any input immediately after it enters
standby mode. Wait a few seconds before taking any action to reenter operation
mode.
Hibernation mode
Note: Computers with the solid state drive (SSD) do not support hibernation
mode.
In hibernation mode, the following occurs:
v The system status, RAM, VRAM, and setup data are stored on the hard disk.
v The system is powered off.
To cause the computer to enter hibernation mode, do any of the following:
v If you are using the APM operating system and have set the mode to Power
switch mode [Hibernation], turn off the power switch.
v If you are using the ACPI operating system and have defined one of the
following actions as the event that causes the system to go into hibernation
mode, perform that action.
– Closing the lid.
– Pressing the power button.
– Pressing Fn+F1 keys.
Also, the computer goes into hibernation mode automatically in either of the
following conditions:
v If a “hibernation time” has been set on the timer, and if the user does not do
any operation with the keyboard, the touch panel, the hard disk drive, the
parallel connector, or the optical drive within that time.
v If the timer conditions are satisfied in suspend mode.
v If you are using the APM operating system and have set the mode to Hibernate
when battery becomes low, and the battery charge becomes critically low.
When the power is turned on, the computer returns from hibernation mode and
resumes operation. The hibernation file in the boot record on the hard disk drive is
read, and system status is restored from the hard disk drive.
38
IdeaPad S9e and S10e Hardware Maintenance Manual
Symptom-to-FRU index
This section contains following information:
v “Numeric error codes”
v “Error messages” on page 41
v “Beep symptoms” on page 42
v “No-beep symptoms” on page 42
v “LCD-related symptoms” on page 43
v “Intermittent problems” on page 44
v “Undetermined problems” on page 44
The symptom-to-FRU index in this section lists symptoms and errors and their
possible causes. The most likely cause is listed first, in boldface type.
Note: Do the FRU replacement or other actions in the sequence shown in the
column headed “FRU or action, in sequence.” If replacing a FRU does not solve
the problem, put the original part back in the computer. Do not replace a
nondefective FRU.
This index can also help you determine, during regular servicing, what FRUs are
likely to need to be replaced next.
A numeric error is displayed for each error detected in POST or system operation.
In the displays, n can be any number.
If no numeric code is displayed, check the narrative descriptions of symptoms. If
the symptom is not described there, go to “Intermittent problems” on page 44.
Note:
For a device not supported by diagnostic codes in the IdeaPad computers, see
the manual for that device.
Numeric error codes
Table 1. Numeric error codes
Symptom or error
FRU or action, in sequence
0200
Failure Fixed Disk.
1. Reseat the hard disk drive.
2. Load Setup Defaults in BIOS Setup
Utility.
3. Hard disk drive.
4. System board.
0210
Stuck Key.
Run interactive tests of the keyboard and
the auxiliary input device.
0211
Keyboard error.
0212
Keyboard Controller Failed.
0220
Monitor type error—Monitor type does not
match the one specified in CMOS.
Load Setup Defaults in BIOS Setup Utility.
0230
Shadow RAM Fails at offset:
System board.
Related service information
39
Table 1. Numeric error codes (continued)
40
Symptom or error
FRU or action, in sequence
0231
System RAM Fails at offset:
1. DIMM.
2. System board.
0232
Extended RAM Fails at address line:
1. DIMM.
2. System board.
0250
System battery dead—Replace and run
SETUP.
1. Charge the backup battery for more
than 8 hours by connecting the ac
adapter.
2. Replace the backup battery and run BIOS
Setup Utility to reset the time and date.
0251
System CMOS checksum bad— Default
configuration used.
1. Charge the backup battery for more
than 8 hours by connecting the ac
adapter.
2. Replace the backup battery and run BIOS
Setup Utility to reset the time and date.
0252
Password checksum bad—The password is
cleared.
Reset the password by running BIOS Setup
Utility.
0260
System timer error.
1. Charge the backup battery for more
than 8 hours by connecting the ac
adapter.
2. Replace the backup battery and run BIOS
Setup Utility to reset the time and date.
3. System board.
0270
Real time clock error.
1. Charge the backup battery for more
than 8 hours by connecting the ac
adapter.
2. Replace the backup battery and run BIOS
Setup Utility to reset the time and date.
3. System board.
0271
Check date and time settings.
Run BIOS Setup Utility to reset the time
and date.
0280
Previous boot incomplete— Default
configuration used.
1. Load “Setup Default” in BIOS Setup
Utility.
2. DIMM.
3. System board.
02F0
CPU ID:xx Failed.
System board.
02F4
EISA CMOS not writable.
1. Load Setup Defaults in BIOS Setup
Utility.
2. Replace the backup battery.
3. System board.
02F5
DMA test failed.
1. DIMM.
2. System board.
02F6
Software NMI failed
1. DIMM.
2. System board.
02F7
Fail-safe timer NMI failed
1. DIMM.
2. System board.
IdeaPad S9e and S10e Hardware Maintenance Manual
Error messages
Table 2. Error messages
Symptom or error
FRU or action, in sequence
Device address conflict.
1. Load “Setup Defaults” in the BIOS
Setup Utility.
2. Backup battery.
3. System board.
Allocation error for device.
1. Load “Setup Defaults” in the BIOS
Setup Utility.
2. Backup battery.
3. System board.
Failing bits: nnnn.
1. DIMM.
2. System board.
Invalid system configuration data.
1. DIMM.
2. System board.
I/O device IRQ conflict.
1. Load “Setup Defaults” in the BIOS
Setup Utility.
2. Backup battery.
3. System board.
Hibernation error.
1. Restore the system configuration to
what it was before the computer
entered hibernation mode.
2. If memory size has been changed,
re-create the hibernation file.
Fan error.
1. Fan.
2. Thermal grease.
3. System board.
Thermal sensing error.
System board.
Cannot boot from any device.
Check the status of device which you want
to boot from.
Device not found.
1. The device you want to boot from.
2. System board.
Device Error.
1. The device you want to boot from.
2. System board.
No valid operating system.
1. Check that the operating system has no
failure and is installed correctly.
2. Reinstall the operation system.
Excluded from boot order.
v Enter the BIOS Setup Utility and add the
device in boot order.
Related service information
41
Beep symptoms
Table 3. Beep symptoms
Symptom or error
FRU or action, in sequence
One beep and a blank, unreadable, or
flashing LCD.
1.
2.
3.
4.
One long and two short beeps, and a blank
or unreadable LCD.
1. System board.
2. LCD assembly.
3. DIMM.
Two short beeps with error codes.
POST error. See “Numeric error codes” on
page 39.
Two short beeps and a blank screen.
1. System board.
2. DIMM.
Three short beeps, pause, three more short
beeps, and one short beep.
1. DIMM.
2. System board
Reseat the LCD connector.
LCD assembly.
External CRT.
System board.
One short beep, pause, three short beeps,
pause, three more short beeps, and one short
beep.
Only the cursor appears.
Reinstall the operating system.
Four cycles of four short beeps and a blank
screen.
System board
Five short beeps and a blank screen.
System board
No-beep symptoms
Table 4. No-beep symptoms
Symptom or error
FRU or action, in sequence
No beep, power-on indicator on, LCD blank, 1. Make sure that every connector is
and no POST.
connected tightly and correctly.
2. DIMM.
3. System board.
42
No beep, power-on indicator on, and LCD
blank during POST.
1. Reseat DIMM.
The power-on password prompt appears.
A power-on password or a supervisor
password is set. Type the password and
press Enter.
The hard-disk password prompt appears.
A hard-disk password is set. Type the
password and press Enter.
IdeaPad S9e and S10e Hardware Maintenance Manual
2. System board.
LCD-related symptoms
Important: The TFT LCD for the notebook computer contains many thin-film
transistors (TFTs). The presence of a small number of dots that are missing,
discolored, or always lighted is characteristic of TFT LCD technology, but
excessive pixel problems can cause viewing concerns. The LCD should be
replaced if the number of missing, discolored, or lighted dots in any background
is as follows:
Table 5. Minimum quantity of defective pixels required for LCD replacement on June 2006
or later manufactured IdeaPad
LCD resolution
Bright dots
Dark dots
Bright and dark dots
XGA, WXGA
5
6
6
WXGA+, SXGA+,
WSXGA+
5
8
10
UXGA, WUXGA,
QXGA
5
13
13
Notes:
v Lenovo will not provide replacement if the LCD is within specification as we
cannot guarantee that any replacement LCD will have zero pixel defects.
v A bright dot means a pixel is always on (white or color.)
v A dark dot means a pixel is always off (black color.)
v One pixel consists of R, G, B sub-pixels.
Table 6. LCD-related symptoms
Symptom or error
FRU or action, in sequence
No beep, power-on indicator on, and a
blank LCD during POST.
System board.
v
v
v
v
LCD
LCD
LCD
LCD
backlight not working.
too dark.
brightness cannot be adjusted.
contrast cannot be adjusted.
v
v
v
v
LCD screen unreadable.
Characters missing pixels.
Screen abnormal.
Wrong color displayed.
Horizontal or vertical lines displayed on
LCD.
1. Reseat the LCD connectors.
2. LCD assembly.
3. System board.
1. See important note for “LCD-related
symptoms.”
2. Reseat all LCD connectors.
3. LCD assembly.
4. System board.
LCD assembly.
Related service information
43
Intermittent problems
Intermittent system hang problems can be due to a variety of causes that have
nothing to do with a hardware defect, such as cosmic radiation, electrostatic
discharge, or software errors. FRU replacement should be considered only when a
problem recurs.
When analyzing an intermittent problem, do the following:
1. Run the diagnostic test for the system board in loop mode at least 10 times.
2. If no error is detected, do not replace any FRUs.
3. If any error is detected, replace the FRU shown by the FRU code. Rerun the
test to verify that no more errors exist.
Undetermined problems
If the diagnostic tests did not identify the adapter or device that has failed, if
wrong devices are installed, or if the system simply is not operating, follow these
procedures to isolate the failing FRU (do not isolate FRUs that have no defects).
Verify that all attached devices are supported by the computer.
Verify that the power supply being used at the time of the failure is operating
correctly. (See “Power system checkout” on page 29.)
1. Turn off the computer.
2. Visually check each FRU for damage. Replace any damaged FRU.
3. Remove or disconnect all of the following devices:
a. Non-IdeaPad devices
b. Devices attached to the docking station or the port replicator
c. Printer, mouse, and other external devices
d. Battery pack
e. Hard disk drive
f. External diskette drive or optical drive
g. DIMM
h. Optical disk or diskette in the internal drive
i. PC Cards
4. Turn on the computer.
5. Determine whether the problem has been solved.
6. If the problem does not recur, reconnect the removed devices one at a time
until you find the failing FRU.
7. If the problem remains, replace the following FRUs one at a time (do not
replace a nondefective FRU):
a. System board
b. LCD assembly
44
IdeaPad S9e and S10e Hardware Maintenance Manual
IdeaPad S9e and S10e
This chapter presents following product-specific service references and
product-specific parts information.
v “Specifications” on page 46
v “Status indicators” on page 47
v “FRU tests” on page 49
v “Fn key combinations” on page 50
v “FRU replacement notices” on page 51
v “Removing and replacing a FRU” on page 54
v “Locations” on page 93
v “Parts list” on page 95
© Copyright Lenovo 2008
45
Specifications
The following table lists the specifications of the IdeaPad S9e and S10e :
Table 7. Specifications
Feature
Description
Processor
v Intel® ATOM™ Processor N270 (1.6 GHz), 533-MHz FSB,
3-MB L2 cache
Bus architecture
v
v
v
v
v
Graphic memory chip
v Intel® 945GSE
Display
v 8.9-inch, 16M colors, WSVGA (1024 × 600 resolution) TFT
color LCD
v 10.1-inch, 16M colors, WSVGA (1024 × 576 resolution) TFT
color LCD
Standard memory
v 512-MB DDR2-667 SDRAM SO-DIMM (PC2-5300) (on the
system board)
Extended memory device
v 512-MB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1
v 1-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1
(maximum of 1.5 GB)
CMOS RAM
v 242 bytes
Hard disk drive
v 80 GB, 5400 rpm, 9.5 mm high, SATA interface
v 160 GB, 5400 rpm, 9.5 mm high, SATA interface
533-MHz FSB
667-MHz DDR2 SDRAM (PC2-5300)
PCI bus
PCI Express bus
DMI
Supported hard disk drives depend on the model.
46
Solid state drive
v 4 GB (on the system board)
I/O port
v
v
v
v
v
v
v
Audio
v Built-in speakers
v Software control volume
Ethernet
v 10/100 Base Ethernet
PCI Express Mini Card
v Broadcom 11b/g WiFi wireless adapter
Bluetooth wireless (some
models)
v Bluetooth with Enhanced Data Rate (BDC-2.1)
Battery
v Li-ion battery (3 cells, 2.6 Ah)
v Li-ion battery (6 cells, 2.4 Ah)
AC adapter
v 40-watt type (20V)
Preinstalled operating
system
v Windows XP Home Edition
v SUSE Linux Enterprise Desktop 10
IdeaPad S9e and S10e Hardware Maintenance Manual
External monitor connector
Stereo headphone jack
Monaural microphone jack
RJ-45 (Ethernet) connector
Universal serial bus (USB) connector × 2
Multi-media reader slot
PCI Express card slot
Status indicators
The system status indicators show the status of the computer, as follows:
1
4
5
2
3
6
Table 8. Status indicators
Indicator
Meaning
1
Caps lock
Blue:
Caps lock mode is enabled. To enable or disable Caps
lock mode, press the CapsLk key.
2
Num lock
Blue:
The numeric keypad on the keyboard is enabled. To
enable or disable the keypad, press and hold the Shift
key, and press the NmLk key.
IdeaPad S9e and S10e
47
Table 8. Status indicators (continued)
48
Indicator
Meaning
3
Drive in use
Data is being read from or written to the hard disk
drive, the solid state drive, or the optical disk drive.
When this indicator is on, do not put the computer into
standby mode or turn off the computer.
Note: Do not move the system while the blue drive-in-use light
is on. Sudden physical shock could cause drive errors.
4
Power
Blue:
5
Battery status
Blue:
The battery is charged to 95% or more of its capacity.
Blinking blue:
The battery is being trickle-charged.
Orange:
The battery is being normally charged.
Off:
The computer is operating on battery power, and the
battery has enough power.
Blinking orange:
The computer is operating on battery power, and the
battery is charged to no more than 8% of capacity.
6
Wireless status
Purple: The wireless LAN and the Bluetooth features are on, and
the radio link is ready for use.
Orange:
The Bluetooth feature is on, and the radio link is ready
for use.
Blue:
The wireless LAN feature is on, and the radio link is
ready for use.
Blinking blue:
The wireless LAN feature is on, and the networks are
being scanned.
Blue:
The computer is on and ready to use. This indicator
stays on whenever the computer is on and is not in
standby mode.
Blinking blue:
The computer is in standby mode.
IdeaPad S9e and S10e Hardware Maintenance Manual
FRU tests
The following table shows the test for each FRU.
Table 9. FRU tests
FRU
Applicable test
System board
1. Diagnostics --> CPU/Coprocessor
2. Diagnostics --> Systemboard
LCD unit
1. Diagnostics --> Video Adapter
2. Interactive Tests --> Video
Keyboard
1. Diagnostics --> Systemboard --> Keyboard
2. Interactive Tests --> Keyboard
Hard disk drive
Diagnostics --> Fixed Disks
Diskette drive
Diagnostics --> Diskette Drives
Optical drive
1. Diagnostics --> Other Devices--> Optical Drive
2. Interactive Tests --> Optical Drive Test
Memory
Diagnostics --> PM Memory
Touch Pad
Interactive Tests --> Mouse
IdeaPad S9e and S10e
49
Fn key combinations
The following table shows the function of each combination of Fn with a function
key.
Table 10. Fn key combinations
Key combination Description
50
Fn+Esc
Turn on or off the integrated camera.
Fn+F1
Put the computer in standby mode. To return to normal operation,
press the power button or the Fn key, without pressing a function key.
Fn+F2
Turn off or on the LCD screen.
Fn+F3
Shift to other connected display devices.
Fn+F4
Reserved.
Fn+F5
Enable or disable the built-in wireless networking features and the
Bluetooth features. If you press Fn+F5, a list of wireless features is
displayed. You can quickly change the power state of each feature in
the list.
Fn+F6
Enable or disable the touch pad.
Fn+F7/NmLk
Enable or disable the numeric keypad.
Fn+F8/ScrLk
Enable or disable Scroll Lock.
Fn+F9/Break
Activate the Break function.
Fn+F10/Pause
Activate the Pause function.
Fn+F11/F12
Activate the F12 function.
Fn+PgUp/Home
Activate the Home function.
Fn+PgDn/End
Activate the End function.
Fn+Ins/SysRq
Activate the System Request.
Fn+up/down
arrow
Increase or decrease display brightness.
Fn+right/left
arrow
Increase or decrease computer volume.
IdeaPad S9e and S10e Hardware Maintenance Manual
FRU replacement notices
This section contains notices related to removing and replacing parts. Read this
section carefully before replacing any FRU.
Screw notices
Loose screws can cause a reliability problem. In the IdeaPad computer, this
problem is addressed with special nylon-coated screws that have the following
characteristics:
v They maintain tight connections.
v They do not easily come loose, even with shock or vibration.
v They are harder to tighten.
v Each one should be used only once.
Do the following when you service this machine:
v Keep the screw kit (for the P/N, see “Miscellaneous parts” on page 107) in your
tool bag.
v Always use new screws.
v Use a torque screwdriver if you have one.
Tighten screws as follows:
v Plastic to plastic
Turn an additional 90 degrees after the screw head touches the surface of the
plastic part:
90 degrees more
(Cross-section)
v Logic card to plastic
Turn an additional 180 degrees after the screw head touches the surface of the
logic card:
180 degrees more
(Cross-section)
v Torque driver
If you have a torque driver, refer to the “Torque” column for each step.
v Make sure that you use the correct screw. If you have a torque screwdriver,
tighten all screws firmly to the torque shown in the table. Never use a screw
that you removed. Use a new one. Make sure that all of the screws are
tightened firmly.
v Ensure torque screw drivers are calibrated correctly following country
specifications.
IdeaPad S9e and S10e
51
Retaining serial numbers
This section includes the following descriptions:
v “Restoring the Product Name and the P/N (part number) of the system unit”
v “Retaining the UUID”
Restoring the Product Name and the P/N (part number) of the
system unit
When the computer was manufactured, the EEPROM on the system board was
loaded with the Product Name and the P/N (part number) of the system unit.
These numbers need to remain the same throughout the life of the computer.
If you replace the system board, you must restore the Product Name and the P/N
of the system unit to their original values.
Table 11. the Product Name and the P/N
BIOS menu text
Meaning
Product Name
Four digits for the machine type and three digits of the
model
P/N
The seven-digit serial number of the system unit
Before replacing the system board, find the original Product Name and P/N by
doing the following:
1. Boot the computer with DOS.
2. To see the Product Name, run the maintenance utility, FL1RW.EXE as follows:
> FL1RW.EXE /r MM
3. To see the P/N, run the maintenance utility, FL1RW.EXE as follows:
> FL1RW.EXE /r SN
4. Write down the result of each of these procedures.
Note: The Product Name and the P/N of the system unit are also written on the
label attached to the bottom of the computer.
After you have replaced the system board, restore the Product Name and the P/N
by doing the following:
1. Boot the computer with DOS.
2. To restore the product name, run the maintenance utility, FL1RW.EXE with the
‘/w MM’ option as the following example.
If the product name is ″4068xxx,″ type the following command:
> FL1RW.EXE /w MM ″4068xxx″
3. To restore the P/N, run the maintenance utility, FL1RW.EXE with the ‘/w SN’
option as the following example.
If the P/N is ″LXXNNN,″ type the following command:
> FL1RW.EXE /w SN ″LxxNNNN″
Retaining the UUID
The Universally Unique Identifier (UUID) is a 128-bit number uniquely assigned to
your computer at production and stored in the EEPROM of your system board.
The algorithm that generates the number is designed to provide unique IDs until
the year A.D. 3400. No two computers in the world have the same number.
52
IdeaPad S9e and S10e Hardware Maintenance Manual
When you replace the system board, you must set the UUID on the new system
board as follows:
1. Boot the system with DOS.
2. Run the maintenance utility, FL1RW.EXE as follows:
> FL1RW.EXE /w UU
A new UUID is created and written. If a valid UUID already exists, it is not
overwritten.
IdeaPad S9e and S10e
53
Removing and replacing a FRU
This section presents directions and drawings for use in removing and replacing a
FRU. Be sure to observe the following general rules:
1. Do not try to service any computer unless you have been trained and certified.
An untrained person runs the risk of damaging parts.
2. Before replacing any FRU, review “FRU replacement notices” on page 51.
3. Begin by removing any FRUs that have to be removed before the failing FRU.
Any such FRUs are listed at the top of the page. Remove them in the order in
which they are listed.
4. Follow the correct sequence in the steps for removing the FRU, as given in the
drawings by the numbers in square callouts.
5. When turning a screw to replace a FRU, turn it in the direction as given by the
arrow in the drawing.
6. When removing the FRU, move it in the direction as given by the arrow in the
drawing.
7. To put the new FRU in place, reverse the removal procedure and follow any
notes that pertain to replacement. For information about connecting and
arranging internal cables, see “Locations” on page 93.
8. When replacing a FRU, use the correct screw as shown in the procedures.
DANGER
Before removing any FRU, turn off the computer, unplug all power cords from
electrical outlets, remove the battery pack, and then disconnect any
interconnecting cables.
Attention: After replacing a FRU, do not turn on the computer until you have
made sure that all screws, springs, and other small parts are in place and none are
loose inside the computer. Verify this by shaking the computer gently and listening
for rattling sounds. Metallic parts or metal flakes can cause electrical short circuits.
Attention: The system board is sensitive to, and can be damaged by, electrostatic
discharge. Before touching it, establish personal grounding by touching a ground
point with one hand or by using an electrostatic discharge (ESD) strap (P/N
6405959).
54
IdeaPad S9e and S10e Hardware Maintenance Manual
Before servicing IdeaPad S9e and S10e
Table 12. Before servicing IdeaPad S9e and S10e
Notice on disconnecting the cable from flip-lock ZIF connector:
Some cables used in the IdeaPad S9e and S10e are connected to the flip-lock ZIF
connectors.
When disconnecting the cable from those connectors, do as shown in this figure.
1
2
IdeaPad S9e and S10e
55
1010 Battery pack
DANGER
Use only the battery specified in the parts list for your computer. Any other
battery could ignite or explode.
Table 13. Removal steps of battery pack
Unlock the battery release lever 1. Holding the battery release lever in the
unlocked position 2, remove the battery pack in the direction shown by arrow
3.
2
2
3
1
1
When installing: Install the battery pack along the slide rails of the slot. Then
make sure that the battery release lever is in the locked position.
56
IdeaPad S9e and S10e Hardware Maintenance Manual
1020 Hard disk drive (HDD) door
For access, remove this FRU:
v “1010 Battery pack” on page 56
Table 14. Removal steps of HDD door
Remove the HDD door as shown in this figure.
Note: Loosen the screws 1, but do not remove them.
2
1
IdeaPad S9e and S10e
57
1030 Hard disk drive (HDD)
For access, remove this FRU:
v “1010 Battery pack” on page 56
v “1020 Hard disk drive (HDD) door” on page 57
Attention:
v Do not drop the hard disk drive or apply any physical shock to it. The hard
disk drive is sensitive to physical shock. Improper handling can cause damage
and permanent loss of data.
v Before removing the drive, have the user make a backup copy of all the
information on it if possible.
v Never remove the drive while the system is operating or is in suspend mode.
Table 15. Removal steps of HDD
In step 1, slide the HDD in the direction of the arrow.
1
58
IdeaPad S9e and S10e Hardware Maintenance Manual
Table 15. Removal steps of HDD (continued)
2
When installing:
1. Align the HDD as shown in this figure, and then place it downward.
1
IdeaPad S9e and S10e
59
Table 15. Removal steps of HDD (continued)
2. Slide the HDD in the direction of the arrow.
2
60
IdeaPad S9e and S10e Hardware Maintenance Manual
1040 DIMM
For access, remove this FRU in order:
v “1010 Battery pack” on page 56
v “1020 Hard disk drive (HDD) door” on page 57
Table 16. Removal steps of dimm
2
1
1
When installing: Insert the notched end of the DIMM into the socket. Press the
DIMM firmly, and pivot it until it snaps into the place. Make sure that it is
firmly fixed in the slot and does not move easily.
IdeaPad S9e and S10e
61
1050 Palm rest assembly
For access, remove this FRU in order:
v “1010 Battery pack” on page 56
Table 17. Removal steps of palm rest assembly
1
1
1
1
Step
Screw (quantity)
Color
Torque
1
M2 × 6 mm, wafer-head, nylon-coated (5)
Black
0.181 Nm
(1.85 kgfcm)
2
3
62
IdeaPad S9e and S10e Hardware Maintenance Manual
2
Table 17. Removal steps of palm rest assembly (continued)
4
7
5
6
Turn the palm rest over, and then disconnect the cable from the flip-lock ZIF
connector.
8
9
IdeaPad S9e and S10e
63
Table 17. Removal steps of palm rest assembly (continued)
When installing:
1. Attach the touch pad cable to the flip-lock ZIF connector on the palm rest.
2. Attach the touch pad cable to the flip-lock ZIF connector on the system board.
3. Attach the microphone connector firmly to the system board.
4. Attach the front side of the palm rest to the front side of the base cover.
5. Press the left and right top edges of the palm rest to fit it into place.
6. Close the LCD cover and turn the computer over. Then fasten the four screws
to secure the palm rest.
64
IdeaPad S9e and S10e Hardware Maintenance Manual
1060 PCI Express Mini Card for wireless LAN
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1050 Palm rest assembly” on page 62
Table 18. Removal steps of PCI Express Mini Card for wireless LAN
In step 1, unplug the jacks by using the removal tool antenna RF connector
(P/N: 08K7159) or pick the connectors with your fingers and gently unplug
them in direction of the arrow.
2
2
1
Step
Screw (quantity)
Color
2
M2 × 2.5 mm, wafer-head, nylon-coated (2) Silver
Torque
0.181 Nm
(1.85 kgfcm)
IdeaPad S9e and S10e
65
Table 18. Removal steps of PCI Express Mini Card for wireless LAN (continued)
3
When installing: Plug the black cable into the jack labeled MAIN or 1 on the
card, and the gray cable into the jack labeled AUX or 2.
66
IdeaPad S9e and S10e Hardware Maintenance Manual
1070 Bluetooth daughter card and Bluetooth cable
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1050 Palm rest assembly” on page 62
Table 19. Removal steps of Bluetooth daughter card and Bluetooth cable
3
1
2
Step
Screw (quantity)
Color
Torque
1
M2 × 4 mm, wafer-head, nylon-coated (1)
Silver
0.181 Nm
(1.85 kgfcm)
When installing: Make sure that the connector 2 is attached firmly.
IdeaPad S9e and S10e
67
Table 19. Removal steps of Bluetooth daughter card and Bluetooth cable (continued)
4
When installing: Make sure that the connector 4 is attached firmly.
68
IdeaPad S9e and S10e Hardware Maintenance Manual
1080 Keyboard
For access, remove this FRU in order:
v “1010 Battery pack” on page 56
v “1020 Hard disk drive (HDD) door” on page 57
v “1050 Palm rest assembly” on page 62
Table 20. Removal steps of keyboard
1
Step
Screw (quantity)
Color
Torque
1
M2 × 6 mm, wafer-head, nylon-coated (1)
Black
0.181 Nm
(1.85 kgfcm)
IdeaPad S9e and S10e
69
Table 20. Removal steps of keyboard (continued)
2
2
3
4
Step
Screw (quantity)
Color
2
M2 × 2.5 mm, wafer-head, nylon-coated (2) Silver
5
5
6
70
IdeaPad S9e and S10e Hardware Maintenance Manual
Torque
0.181 Nm
(1.85 kgfcm)
Table 20. Removal steps of keyboard (continued)
When installing: Make sure that the keyboard edges a are under the frame as
shown in this figure. Then press the keys to latch the keyboard firmly in place.
a
a
a
a
IdeaPad S9e and S10e
71
1090 Keyboard bezel
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1020 Hard disk drive (HDD) door” on page 57
v “1050 Palm rest assembly” on page 62
v “1080 Keyboard” on page 69
Table 21. Removal steps of keyboard bezel
1
1
Step
Screw (quantity)
Color
Torque
1
M2 × 6 mm, wafer-head, nylon-coated (2)
Black
0.181 Nm
(1.85 kgfcm)
2
2
Step
2
72
Screw
cap
Screw (quantity)
Color
Torque
M2 × 4 mm, wafer-head,
nylon-coated (2)
Silver
0.181 Nm
(1.85 kgfcm)
IdeaPad S9e and S10e Hardware Maintenance Manual
Table 21. Removal steps of keyboard bezel (continued)
6
3
5
4
Step
Screw (quantity)
Color
Torque
3-6
M2 × 6 mm, wafer-head, nylon-coated (2)
Black
0.181 Nm
(1.85 kgfcm)
In step 7, detach the claws. Then remove the keyboard bezel in the direction
shown by arrow 8.
7
7
7
7
8
When installing: Make sure that all the claws are attached firmly.
IdeaPad S9e and S10e
73
1100 fan assembly
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1020 Hard disk drive (HDD) door” on page 57
v “1030 Hard disk drive (HDD)” on page 58
v “1040 DIMM” on page 61
v “1050 Palm rest assembly” on page 62
v “1060 PCI Express Mini Card for wireless LAN” on page 65
v “1070 Bluetooth daughter card and Bluetooth cable” on page 67
v “1080 Keyboard” on page 69
v “1090 Keyboard bezel” on page 72
Table 22. Removal steps of fan assembly
2
1
3
4
74
Step
Screw (quantity)
Color
Torque
1
M2 × 4 mm, wafer-head, nylon-coated (1)
Silver
0.181 Nm
(1.85 kgfcm)
IdeaPad S9e and S10e Hardware Maintenance Manual
Table 22. Removal steps of fan assembly (continued)
8
5
6
7
Step
Screw (quantity)
Color
Torque
8
M2 × 4 mm, wafer-head, nylon-coated (1)
Silver
0.181 Nm
(1.85 kgfcm)
When installing: Make sure that the speaker connector 5 and the camera
connector 7 are attached to the system board firmly.
IdeaPad S9e and S10e
75
Table 22. Removal steps of fan assembly (continued)
In step 10 , remove the system board and the fan assembly together from the
base cover assembly.
10
9
Note: The fan assembly is attached to the underside of the system board.
2
3
1
76
Step
Screw (quantity)
Color
Torque
1-3
M2 × 4 mm, wafer-head, nylon-coated (3)
Silver
0.181 Nm
(1.85 kgfcm)
IdeaPad S9e and S10e Hardware Maintenance Manual
Table 22. Removal steps of fan assembly (continued)
4
5
When installing: Make sure that the fan connector is attached to the system
board firmly.
When installing:
v Before you attach the fan assembly to the computer, peel the thin film off from
the rubber a.
a
a
IdeaPad S9e and S10e
77
1110 System board and backup battery
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1020 Hard disk drive (HDD) door” on page 57
v “1030 Hard disk drive (HDD)” on page 58
v “1040 DIMM” on page 61
v “1050 Palm rest assembly” on page 62
v “1060 PCI Express Mini Card for wireless LAN” on page 65
v “1070 Bluetooth daughter card and Bluetooth cable” on page 67
v “1080 Keyboard” on page 69
v “1090 Keyboard bezel” on page 72
v “1100 fan assembly” on page 74
78
IdeaPad S9e and S10e Hardware Maintenance Manual
Table 23. Removal steps of backup battery
Following components soldered on the system board are extremely sensitive.
When you service the system board, avoid any kind of rough handling.
a
b
c
d
e
f
SSD (Solid State Drive)
ICH (I/O Controller Hub)
On-board 512 MB memory
CPU
MCH (Memory Controller Hub)
SSD controller
Top
a
Bottom
d
c
e
b
f
IdeaPad S9e and S10e
79
DANGER
Use only the battery specified in the parts list for your computer. Any other
battery could ignite or explode.
Table 24. Removal steps of backup battery
1
2
When installing: Make sure that the battery connector is attached firmly.
80
IdeaPad S9e and S10e Hardware Maintenance Manual
1120 LCD assembly
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1020 Hard disk drive (HDD) door” on page 57
v “1030 Hard disk drive (HDD)” on page 58
v “1040 DIMM” on page 61
v “1050 Palm rest assembly” on page 62
v “1060 PCI Express Mini Card for wireless LAN” on page 65
v “1070 Bluetooth daughter card and Bluetooth cable” on page 67
v “1080 Keyboard” on page 69
v “1090 Keyboard bezel” on page 72
v “1100 fan assembly” on page 74
Table 25. Removal steps of LCD assembly
In step 1, release the antenna cables from the cable guides of the base cover.
2
2
1
1
1
1
1
Step
Screw (quantity)
Color
Torque
1
M2 × 4 mm, wafer-head, nylon-coated (2)
Silver
0.181 Nm
(1.85 kgfcm)
IdeaPad S9e and S10e
81
Table 25. Removal steps of LCD assembly (continued)
3
3
When installing: Route the antenna cables along the cable guides. As you route
the cables, make sure that they are not subjected to any tension. Tension could
cause the cables to be damaged by the cable guides, or a wire to be broken.
82
IdeaPad S9e and S10e Hardware Maintenance Manual
1130 Speaker and base cover assembly
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1020 Hard disk drive (HDD) door” on page 57
v “1030 Hard disk drive (HDD)” on page 58
v “1040 DIMM” on page 61
v “1050 Palm rest assembly” on page 62
v “1060 PCI Express Mini Card for wireless LAN” on page 65
v “1070 Bluetooth daughter card and Bluetooth cable” on page 67
v “1080 Keyboard” on page 69
v “1090 Keyboard bezel” on page 72
v “1100 fan assembly” on page 74
v “1120 LCD assembly” on page 81
Table 26. Removal steps of speaker and base cover assembly
1
1
When installing: Route the speaker cables as shown in this figure.
IdeaPad S9e and S10e
83
Applying labels to the base cover:
The new base cover FRU is shipped with a kit containing labels of several kinds.
When you replace the base cover, you need to apply the following labels:
1
Product label
2
Homologation label
Following labels need to be peeled off from the old base cover, and need to be
put on the new base cover.
3
Serial number label
4
China label or Israel label
5
MAC address label
6
Windows license label (COA)
For some models, you also need to apply one or two FCC labels. Check the old
base cover; if it has one or two FCC labels, find duplicates of them in the label
kit and apply them to the new base cover.
For the location of each label, refer the following figure:
84
6
1
5
2
4
3
IdeaPad S9e and S10e Hardware Maintenance Manual
2010 LCD front bezel
For access, remove this FRU:
v “1010 Battery pack” on page 56
Table 27. Removal steps of LCD front bezel
1
2
1
2
Step
Screw cap Screw (quantity)
Color
Torque
1
M2 × 4 mm, wafer-head,
wafer-coated (2)
Silver
0.181 Nm
(1.85 kgfcm)
2
M2 × 4 mm, wafer-head,
wafer-coated (2)
Silver
0.181 Nm
(1.85 kgfcm)
In step 3 and 4, detach the claws. Then remove the LCD front bezel.
3
3
3
3
3
4
3
4
3
4
4
When installing: Make sure that all the claws are attached firmly.
IdeaPad S9e and S10e
85
2020 Hinges
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1020 Hard disk drive (HDD) door” on page 57
v “1030 Hard disk drive (HDD)” on page 58
v “1040 DIMM” on page 61
v “1050 Palm rest assembly” on page 62
v “1060 PCI Express Mini Card for wireless LAN” on page 65
v “1070 Bluetooth daughter card and Bluetooth cable” on page 67
v “1080 Keyboard” on page 69
v “1090 Keyboard bezel” on page 72
v “1100 fan assembly” on page 74
v “1120 LCD assembly” on page 81
v “2010 LCD front bezel” on page 85
Table 28. Removal steps of hinges
Remove the hinge caps.
1
1
86
IdeaPad S9e and S10e Hardware Maintenance Manual
Table 28. Removal steps of hinges (continued)
Remove the hinges from the LCD rear cover.
2
3
2
2
3
2
Step
Screw (quantity)
Color
Torque
2
M2 × 4 mm, wafer-head, wafer-coated (4)
Silver
0.181 Nm
(1.85 kgfcm)
When installing: Route the cables in this figure.
IdeaPad S9e and S10e
87
2030 LCD panel and LCD cable
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1020 Hard disk drive (HDD) door” on page 57
v “1030 Hard disk drive (HDD)” on page 58
v “1040 DIMM” on page 61
v “1050 Palm rest assembly” on page 62
v “1060 PCI Express Mini Card for wireless LAN” on page 65
v “1070 Bluetooth daughter card and Bluetooth cable” on page 67
v “1080 Keyboard” on page 69
v “1090 Keyboard bezel” on page 72
v “1100 fan assembly” on page 74
v “1120 LCD assembly” on page 81
v “2010 LCD front bezel” on page 85
v “2020 Hinges” on page 86
Table 29. Removal steps of LCD panel and LCD cable
1
88
IdeaPad S9e and S10e Hardware Maintenance Manual
Table 29. Removal steps of LCD panel and LCD cable (continued)
2
Remove the LCD brackets from the LCD panel.
3
3
4
3
4
3
Step
Screw (quantity)
Color
3
M2 × 2.5 mm, wafer-head, nylon-coated (4) Silver
Torque
0.181 Nm
(1.85 kgfcm)
IdeaPad S9e and S10e
89
Table 29. Removal steps of LCD panel and LCD cable (continued)
Turn the LCD panel over, and then remove the LCD cable.
5
6
7
When installing: Make sure that the LCD cable connector is attached firmly.
90
IdeaPad S9e and S10e Hardware Maintenance Manual
2040 Integrated camera, camera cable, and LCD rear cover
assembly
For access, remove these FRUs in order:
v “1010 Battery pack” on page 56
v “1020 Hard disk drive (HDD) door” on page 57
v “1030 Hard disk drive (HDD)” on page 58
v “1040 DIMM” on page 61
v “1050 Palm rest assembly” on page 62
v “1060 PCI Express Mini Card for wireless LAN” on page 65
v “1070 Bluetooth daughter card and Bluetooth cable” on page 67
v “1080 Keyboard” on page 69
v “1090 Keyboard bezel” on page 72
v “1100 fan assembly” on page 74
v “1120 LCD assembly” on page 81
v “2010 LCD front bezel” on page 85
v “2020 Hinges” on page 86
v “2030 LCD panel and LCD cable” on page 88
Table 30. Removal steps of Integrated camera, camera cable, and LCD rear cover assembly
In step 1, release the camera cable from the cable guides of the rear cover.
2
1
1
When installing: Make sure that the camera connector is attached firmly.
IdeaPad S9e and S10e
91
Table 30. Removal steps of Integrated camera, camera cable, and LCD rear cover
assembly (continued)
4
3
When installing: Route the camera cable as shown in this figure.
92
IdeaPad S9e and S10e Hardware Maintenance Manual
Locations
Front view
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Integrated camera (for some models)
Status indicators
Note: For the description of each indicator, see “Status indicators” on page
47.
Novo button
Wireless device switch
Security keyhole
RJ-45 (Ethernet) connector
Universal serial bus (USB) connector
Microphone jack
Stereo headphone jack
PCI Express card slot
Built-in speakers
Touch pad
Touch pad buttons
Power button
1
2
14
3
4
5
11
13
12
11
6
7
8
9
10
IdeaPad S9e and S10e
93
Bottom view
1
2
3
4
5
6
7
8
9
Battery pack latch - spring loaded
Battery pack
Battery pack latch - manual
AC power connector
External monitor connector
Multi-media reader slot
Universal serial bus (USB) connector
Status indicators
Note: For the description of each indicator, see “Status indicators” on page
47.
Hard disk drive (HDD) and DIMM compartment
1
9
2
3
4
5
6
8
7
94
IdeaPad S9e and S10e Hardware Maintenance Manual
Parts list
This section contains following lists of the service parts.
v “Overall” on page 96
v “LCD FRUs” on page 101
v “Keyboard” on page 106
v “Miscellaneous parts” on page 107
v “AC adapters” on page 108
v “Power cords” on page 109
v “Recovery discs” on page 110
v “Common service tools” on page 114
Notes:
v Each FRU is available for all types or models, unless specific types or models
are specified.
v FRU with specific models listed and described as xxU (where U is an example
of a country designator) should be used for all models ending in U.
v FRU with specific models listed and described as 3Dx (where 3D is an
example of a unique configuration) should be used for all of these models,
unless specific country or region designator is specified.
v A CRU (customer replaceable unit) is identified by a single asterisk (*) or two
asterisks (**) in the CRU ID column. An N in the CRU ID column means that
the part is not a CRU. A single asterisk (*) means that the part is a Self-service
CRU; two asterisks (**) means that the part is an Optional-service CRU.
IdeaPad computers contain the following types of CRUs:
Self-service CRUs
These CRUs unplug or are held by no more than two screws.
Examples of these types of CRUs include an AC adapter, a power
cord, a battery, and a hard disk drive. Other Self-service CRUs
depending on product design may include a memory, a wireless card,
a keyboard, and a palm rest with finger print reader and touchpad.
Optional-service CRUs
These CRUs are isolated parts within the computer that are concealed
by an access panel that is typically secured by more than two screws.
Once the access panel is removed, the specific CRU is visible.
v A RoHS compliant FRU is identified by an R. An N in the RoHS ID column
means the part is not a RoHS compliant FRU.
v FRUs marked with OP are available as options.
IdeaPad S9e and S10e
95
Overall
1
15
2
14
3
13
4
12
5
6
7
11
8
10
9
a
Table 31. Parts list—Overall
No.
96
FRU
a
See “Miscellaneous parts” on page 107.
1
LCD unit (see “LCD FRUs” on page 101.)
IdeaPad S9e and S10e Hardware Maintenance Manual
FRU no.
RoHS
ID
CRU
ID
Table 31. Parts list—Overall (continued)
No.
FRU
FRU no.
RoHS
ID
CRU
ID
2
Keyboard bezel assembly, black
v 4068-CTO, 22x, 23x, 24x, 27x, 28x, 29x, 2Ax, 2Bx, 32x,
35x ,38x, 3Bx, 3Ex, 42x, 46x, 4Ax, 4Ex, 4Jx, 4Nx, 4Sx,
4Wx, A2x, A3x, A4x, A5x, A6x, A7x, A8x, A9x, AAx,
ABx, ACx, ADx, AEx, AFx
v 4187-CTO, 27x, 29x, 32x, 33x, 34x, 37x, 39x, 3Ax, 3Dx,
3Hx, 3Jx, 42x, 45x, 48x, 4Bx, 4Ex, 52x, 55x, 58x, 5Bx,
5Ex, 5Hx, 5Lx, 5Px, DRx, ERx
45N3868
R
N
2
Keyboard bezel assembly, white
v 4068-CTO, 33x, 36x, 39x, 3Cx, 3Fx, 43x, 44x, 47x, 48x,
4Bx, 4Cx, 4Fx, 4Gx, 4Kx, 4Lx, 4Px, 4Qx, 4Tx, 4Ux,
4Xx, 4Yx, AGx, AHx, AJx
v 4187-CTO, 43x, 46x, 49x, 4Cx, 4Fx, 53x, 54x, 56x, 57x,
59x, 5Ax, 5Cx, 5Dx, 5Fx, 5Gx, 5Jx, 5Kx, 5Mx, 5Nx,
5Qx, 5Rx
45N5103
R
N
3
Palm rest assembly, black
45N3816
R
**
3
Palm rest assembly, white
45N5097
R
**
4
System board with Intel ATOM Processor N270 (1.6
42W8135
GHz) without SSD
v 4068-CTO, 23x, 24x, 27x, 29x, 2Ax, 2Bx, 35x, 36x, 38x,
39x, 3Bx, 3Cx, 42x, 43x, 44x, 4Ax, 4Bx, 4Cx, 4Ex, 4Fx,
4Gx, 4Jx, 4Kx, 4Lx, 4Sx, 4Tx, 4Ux, 4Wx, 4Xx, 4Yx,
A3x, A5x, A7x, A8x, A9x, AAx, ABx, AEx, AFx, AGx,
AHx, AJx
v 4187-CTO, 27x, 29x, 33x, 34x, 37x, 39x, 3Ax, 3Dx, 3Hx,
3Jx, 42x, 43x, 48x, 49x, 4Bx, 4Cx, 52x, 53x, 54x, 58x,
59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Fx, 5Gx, 5Lx, 5Mx,
5Nx, 5Px, 5Qx, 5Rx
R
N
4
System board with Intel ATOM Processor N270 (1.6
GHz) with SSD
v 4068-CTO, 22x, 28x, 32x, 33x, 3Ex, 3Fx, 46x, 47x, 48x
,4Nx, 4Px, 4Qx, A2x, A4x, A6x, ACx, ADx
v 4187-CTO, 32x, 45x, 46x, 4Ex, 4Fx, 55x, 56x, 57x, 5Hx,
5Jx, 5Kx, DRx, ERx
42W8136
R
N
5
Backup battery
92P1233
R
N
6
Bluetooth cable
44C9902
v 4068-CTO, 24x, 27x, 29x, 35x, 36x, 38x, 39x, 3Bx, 3Cx,
3Ex, 3Fx, 42x, 43x, 44x, 4Ax, 4Bx, 4Cx, 4Ex, 4Fx, 4Gx,
4Jx, 4Kx, 4Lx, 4Sx, 4Tx, 4Ux, 4Wx, 4Xx, 4Yx, A6x,
A7x, AAx, ABx, AFx, AGx, AHx, AJx
v 4187-CTO, 27x, 29x, 33x, 37x, 3Ax, 3Dx, 3Hx, 3Jx, 42x,
43x, 48x, 49x, 4Bx, 4Cx, 4Ex, 4Fx, 52x, 53x, 54x, 58x,
59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Fx, 5Gx, 5Lx, 5Mx,
5Nx, 5Px, 5Qx, 5Rx
R
N
7
Bluetooth daughter card (BDC-2.1)
43Y6491
v 4068-CTO, 24x, 27x, 29x, 35x, 36x, 38x, 39x, 3Bx, 3Cx,
3Ex, 3Fx, 42x, 43x, 44x, 4Ax, 4Bx, 4Cx, 4Ex, 4Fx, 4Gx,
4Jx, 4Kx, 4Lx, 4Sx, 4Tx, 4Ux, 4Wx, 4Xx, 4Yx, A6x,
A7x, AAx, ABx, AFx, AGx, AHx, AJx
v 4187-CTO, 27x, 29x, 33x, 37x, 3Ax, 3Dx, 3Hx, 3Jx, 42x,
43x, 48x, 49x, 4Bx, 4Cx, 4Ex, 4Fx, 52x, 53x, 54x, 58x,
59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Fx, 5Gx, 5Lx, 5Mx,
5Nx, 5Px, 5Qx, 5Rx
R
N
IdeaPad S9e and S10e
97
Table 31. Parts list—Overall (continued)
No.
98
FRU
FRU no.
RoHS
ID
CRU
ID
8
Battery pack, 3 cell, black
v 4068-CTO, 22x, 23x, 24x, 27x, 28x, 2Bx, 32x, 35x, 38x,
3Bx, 3Ex, 42x, 46x, 4Ax, 4Nx, 4Sx, A3x, A4x, A6x,
A8x, A9x, AAx, ABx, ACx, AEx
v 4187-CTO, 27x, 29x, 32x, 34x, 37x, 39x, 3Dx, 3Hx, 3Jx,
42x, 45x, 48x, 4Bx, 4Ex, 52x, 55x, 58x, 5Hx, 5Lx
42T4587
R
*
8
Battery pack, 3 cell, black
v 4068-CTO, 22x, 23x, 24x, 27x, 28x, 2Bx, 32x, 35x, 38x,
3Bx, 3Ex, 42x, 46x, 4Ax, 4Nx, 4Sx, A3x, A4x, A6x,
A8x, A9x, AAx, ABx, ACx, AEx
v 4187-CTO, 27x, 29x, 32x, 34x, 37x, 39x, 3Dx, 3Hx, 3Jx,
42x, 45x, 48x, 4Bx, 4Ex, 52x, 55x, 58x, 5Hx, 5Lx
42T4591
R
*
8
Battery pack, 6 cell, black
v 4068-CTO, 29x, 2Ax, 4Ex, 4Jx, 4Wx, A2x, A5x, A7x,
ADx, AFx
v 4187-CTO, 33x, 3Ax, 5Bx, 5Ex, 5Px, DRx, ERx
42T4589
R
*
8
Battery pack, 6 cell, black
v 4068-CTO, 29x, 2Ax, 4Ex, 4Jx, 4Wx, A2x, A5x, A7x,
ADx, AFx
v 4187-CTO, 33x, 3Ax, 5Bx, 5Ex, 5Px, DRx, ERx
42T4593
R
*
8
Battery pack, 3 cell, white
v 4068-CTO, 33x, 36x, 39x, 3Cx, 3Fx, 43x, 44x, 47x, 48x,
4Bx, 4Cx, 4Px, 4Qx, 4Tx, 4Ux
v 4187-CTO, 43x, 46x, 49x, 4Cx, 4Fx, 53x, 54x, 56x, 57x,
59x, 5Ax, 5Jx, 5Kx, 5Mx, 5Nx
42T4680
R
*
8
Battery pack, 3 cell, white
v 4068-CTO, 33x, 36x, 39x, 3Cx, 3Fx, 43x, 44x, 47x, 48x,
4Bx, 4Cx, 4Px, 4Qx, 4Tx, 4Ux
v 4187-CTO, 43x, 46x, 49x, 4Cx, 4Fx, 53x, 54x, 56x, 57x,
59x, 5Ax, 5Jx, 5Kx, 5Mx, 5Nx
42T4684
R
*
8
Battery pack, 6 cell, white
v 4068-CTO, 4Fx, 4Gx, 4Kx, 4Lx, 4Xx, 4Yx, AJx, AGx,
AHx
v 4187-CTO, 5Cx, 5Dx, 5Fx, 5Gx, 5Qx, 5Rx
42T4682
R
*
8
Battery pack, 6 cell, white
v 4068-CTO, 4Fx, 4Gx, 4Kx, 4Lx, 4Xx, 4Yx, AJx, AGx,
AHx
v 4187-CTO, 5Cx, 5Dx, 5Fx, 5Gx, 5Qx, 5Rx
42T4686
R
*
9
SATA hard disk drive, 80 GB, 9.5 mm, 5,400 rpm
41W0063
v 4068-CTO, 23x, 27x, 29x, 2Bx, 35x, 36x, 38x, 39x, 3Bx,
3Cx, 42x, 43x, 44x, 4Ax, 4Bx, 4Cx, 4Ex, 4Fx, 4Gx, A3x,
A8x, AAx, AEx, AFx
v 4187-CTO, 29x, 33x, 34x, 39x, 3Ax, 3Hx, 42x, 43x, 48x,
49x, 4Bx, 4Cx, 52x, 53x, 54x, 58x, 59x, 5Ax, 5Bx, 5Cx,
5Dx
R
*
9
SATA hard disk drive, 80 GB, 9.5 mm, 5,400 rpm
41W0065
v 4068-CTO, 23x, 27x, 29x, 2Bx, 35x, 36x, 38x, 39x, 3Bx,
3Cx, 42x, 43x, 44x, 4Ax, 4Bx, 4Cx, 4Ex, 4Fx, 4Gx, A3x,
A8x, AAx, AEx, AFx
v 4187-CTO, 29x, 33x, 34x, 39x, 3Ax, 3Hx, 42x, 43x, 48x,
49x, 4Bx, 4Cx, 52x, 53x, 54x, 58x, 59x, 5Ax, 5Bx, 5Cx,
5Dx
R
*
IdeaPad S9e and S10e Hardware Maintenance Manual
Table 31. Parts list—Overall (continued)
No.
FRU
FRU no.
RoHS
ID
CRU
ID
9
SATA hard disk drive, 160 GB, 9.5 mm, 5,400 rpm
v 4068-CTO, 24x, 2Ax, 4Jx, 4Kx, 4Lx, 4Sx, 4Tx, 4Ux,
4Wx, 4Xx, 4Yx, A5x, A7x, A9x, ABx, AGx, AHx, AJx
v 4187-CTO, 27x, 37x, 3Dx, 3Jx, 5Ex, 5Fx, 5Gx, 5Lx,
5Mx, 5Nx, 5Px, 5Qx, 5Rx
41W0059
R
*
9
SATA hard disk drive, 160 GB, 9.5 mm, 5,400 rpm
v 4068-CTO, 24x, 2Ax, 4Jx, 4Kx, 4Lx, 4Sx, 4Tx, 4Ux,
4Wx, 4Xx, 4Yx, A5x, A7x, A9x, ABx, AGx, AHx, AJx
v 4187-CTO, 27x, 37x, 3Dx, 3Jx, 5Ex, 5Fx, 5Gx, 5Lx,
5Mx, 5Nx, 5Px, 5Qx, 5Rx
41W0061
R
*
10
Base cover assembly, dark silver for 4068
v 4068-CTO, 22x, 23x, 24x, 27x, 28x, 29x, 2Ax, 2Bx, A2x,
A3x, A4x, A5x, A6x, A7x, A8x, A9x, AAx, ABx, ACx,
ADx, AEx, AFx
45N3869
R
N
10
Base cover assembly, blue for 4068
v 4068-CTO, AHx
45N5104
R
N
10
Base cover assembly, red for 4068
v 4068-CTO, 44x, 48x, 4Cx, 4Gx, 4Lx, 4Qx, 4Ux, 4Yx
45N5105
R
N
10
Base cover assembly, pink for 4068
v 4068-CTO, AJx
45N5106
R
N
10
Base cover assembly, white for 4068
v 4068-CTO, 33x, 36x, 39x, 3Cx, 3Fx, 43x, 47x, 4Bx, 4Fx,
4Kx, 4Px, 4Tx, 4Xx, AGx
45N5107
R
N
10
Base cover assembly, painted black for 4068
v 4068-CTO
45N5108
R
N
10
Base cover assembly, material black for 4068
v 4068-CTO, 32x, 35x, 38x, 3Bx, 3Ex, 42x, 46x, 4Ax, 4Ex,
4Jx, 4Nx, 4Sx, 4Wx
45N5117
R
N
10
Base cover assembly, dark silver for 4187
v 4187-CTO, 27x, 29x, 32x, 33x, 34x, 37x, 39x, 3Ax, 3Dx,
3Hx, 3Jx, DRx, ERx
45N3892
R
N
10
Base cover assembly, blue for 4187
v 4187-CTO
45N5109
R
N
10
Base cover assembly, red for 4187
v 4187-CTO, 54x, 57x, 5Ax, 5Dx, 5Gx, 5Kx, 5Nx, 5Rx
45N5110
R
N
10
Base cover assembly, pink for 4187
v 4187-CTO
45N5111
R
N
10
Base cover assembly, white for 4187
v 4187-CTO, 43x, 46x, 49x, 4Cx, 4Fx, 53x, 56x, 59x, 5Cx,
5Fx, 5Jx, 5Mx, 5Qx
45N5112
R
N
10
Base cover assembly, painted black for 4187
v 4187-CTO
45N5113
R
N
10
Base cover assembly, material black for 4187
v 4187-CTO, 42x, 45x, 48x, 4Bx, 4Ex, 52x, 55x, 58x, 5Bx,
5Ex, 5Hx, 5Lx, 5Px
45N5118
R
N
11
Speaker kit
45N3865
R
N
IdeaPad S9e and S10e
99
Table 31. Parts list—Overall (continued)
No.
100
FRU
FRU no.
RoHS
ID
CRU
ID
12
512-MB DDR2-533 SDRAM SO-DIMM (PC2-5300) card
v 4068-CTO, 23x, 27x, 28x, 29x, 38x, 39x, 3Bx, 3Cx, 42x,
43x, 44x, 4Ax, 4Bx, 4Cx, 4Ex, 4Fx, 4Gx, 4Sx, 4Tx, 4Ux,
4Wx, 4Xx, 4Yx, A4x, A8x, AAx, AFx, AGx, AHx, AJx
v 4187-CTO, 29x, 33x, 3Ax, 3Dx, 3Hx, 42x, 43x, 4Bx,
4Cx, 52x, 53x, 54x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Lx,
5Mx, 5Nx, 5Px, 5Qx, 5Rx, DRx, ERx
40Y8402
R
*
12
1-GB DDR2-533 SDRAM SO-DIMM (PC2-5300) card
v 4068-CTO, 24x, 2Ax, 4Jx, 4Kx, 4Lx, A2x, A5x, A7x,
ABx
v 4187-CTO, 27x, 3Jx, 5Ex, 5Fx, 5Gx
40Y8403
R
*
13
Fan assembly
45N3864
R
N
14
Broadcom 11b/g WiFi Wireless Adapter
43Y6487
R
**
14
Broadcom 11b/g WiFi Wireless Adapter
43Y6489
R
**
15
Keyboard (see “Keyboard” on page 106.)
—
AC adapter (see “AC adapters” on page 108.)
IdeaPad S9e and S10e Hardware Maintenance Manual
LCD FRUs
In IdeaPad S9e and S10e, there are following types of LCDs.
v “8.9-in. WSVGA TFT” on page 102
v “10.1-in. WSVGA TFT” on page 104
1
e
d
c
2
b
7
3
4
6
5
IdeaPad S9e and S10e
101
8.9-in. WSVGA TFT
Table 32. Parts list—8.9-in. WSVGA TFT
No.
FRU
FRU no.
RoHS
ID
CRU
ID
b - e See “Miscellaneous parts” on page 107.
102
1
LCD front bezel assembly, black for 8.9-in. WSVGA
v 4068-CTO, 22x, 23x, 24x, 27x, 28x, 29x, 2Ax, 2Bx, 32x,
35x, 38x, 3Bx, 3Ex
v 4187-CTO, 27x, 29x, 32x, 33x, 34x, 37x, 42x, 45x, 48x,
4Bx, 4Ex, DRx
45N3859
R
N
1
LCD front bezel assembly, white for 8.9-in. WSVGA
v 4068-CTO, 33x, 36x, 39x, 3Cx, 3Fx
v 4187-CTO, 43x, 46x, 49x, 4Cx, 4Fx
45N5090
R
N
2
LCD panel, 8.9-in. WSVGA
v 4068-CTO, 22x, 23x, 24x, 27x, 28x, 29x, 2Ax, 2Bx, 32x,
33x, 35x, 36x, 38x, 39x, 3Bx, 3Cx, 3Ex, 3Fx
v 4187-CTO, 27x, 29x, 32x, 33x, 34x, 37x, 42x, 43x, 45x,
46x, 48x, 49x, 4Bx, 4Cx, 4Ex, 4Fx, DRx
42T0599
R
N
2
LCD panel, 8.9-in. WSVGA
v 4068-CTO, 22x, 23x, 24x, 27x, 28x, 29x, 2Ax, 2Bx, 32x,
33x, 35x, 36x, 38x, 39x, 3Bx, 3Cx, 3Ex, 3Fx
v 4187-CTO, 27x, 29x, 32x, 33x, 34x, 37x, 42x, 43x, 45x,
46x, 48x, 49x, 4Bx, 4Cx, 4Ex, 4Fx, DRx
42T0603
R
N
2
LCD panel, 8.9-in. WSVGA
v 4068-CTO, 22x, 23x, 24x, 27x, 28x, 29x, 2Ax, 2Bx, 32x,
33x, 35x, 36x, 38x, 39x, 3Bx, 3Cx, 3Ex, 3Fx
v 4187-CTO, 27x, 29x, 32x, 33x, 34x, 37x, 42x, 43x, 45x,
46x, 48x, 49x, 4Bx, 4Cx, 4Ex, 4Fx, DRx
42T0601
R
N
3
Integrated camera for 8.9-in. WSVGA
v 4068-CTO, 22x, 23x, 24x, 27x, 28x, 29x, 2Ax, 2Bx, 32x,
33x, 35x, 36x, 38x, 39x, 3Bx, 3Cx, 3Ex, 3Fx
v 4187-CTO, 27x, 29x, 32x, 33x, 34x, 37x, 42x, 43x, 45x,
46x, 48x, 49x, 4Bx, 4Cx, 4Ex, 4Fx, DRx
42T4199
R
N
3
Integrated camera for 8.9-in. WSVGA
v 4068-CTO, 22x, 23x, 24x, 27x, 28x, 29x, 2Ax, 2Bx, 32x,
33x, 35x, 36x, 38x, 39x, 3Bx, 3Cx, 3Ex, 3Fx
v 4187-CTO, 27x, 29x, 32x, 33x, 34x, 37x, 42x, 43x, 45x,
46x, 48x, 49x, 4Bx, 4Cx, 4Ex, 4Fx, DRx
42T4201
R
N
4
Camera cable
44C9901
R
N
5
LCD rear cover assembly, dark silver with wireless LAN 45N3861
antenna
v 4068-CTO, 22x, 23x, 24x, 27x, 28x, 29x, 2Ax, 2Bx
v 4187-CTO, 27x, 29x, 32x, 33x, 34x, 37x, DRx
R
N
5
LCD rear cover assembly, blue with wireless LAN
antenna
v 4068-CTO
v 4187-CTO
45N5092
R
N
5
LCD rear cover assembly, red with wireless LAN
antenna
v 4068-CTO
v 4187-CTO
45N5093
R
N
IdeaPad S9e and S10e Hardware Maintenance Manual
Table 32. Parts list—8.9-in. WSVGA TFT (continued)
No.
FRU
FRU no.
RoHS
ID
CRU
ID
5
LCD rear cover assembly, pink with wireless LAN
antenna
v 4068-CTO
v 4187-CTO
45N5094
R
N
5
LCD rear cover assembly, white with wireless LAN
antenna
v 4068-CTO, 33x, 36x, 39x, 3Cx, 3Fx
v 4187-CTO, 43x, 46x, 49x, 4Cx, 4Fx
45N5095
R
N
5
LCD rear cover assembly, black with wireless LAN
antenna
v 4068-CTO, 32x, 35x, 38x, 3Bx, 3Ex
v 4187-CTO, 42x, 45x, 48x, 4Bx, 4Ex
45N5096
R
N
6
LCD cable assembly for 8.9-in. WSVGA
v 4068-CTO, 22x, 23x, 24x, 27x, 28x, 29x, 2Ax, 2Bx, 32x,
33x, 35x, 36x, 38x, 39x, 3Bx, 3Cx, 3Ex, 3Fx
v 4187-CTO, 32x, 33x, 34x, 27x, 29x, 37x, 42x, 43x, 45x,
46x, 48x, 49x, 4Bx, 4Cx, 4Ex, 4Fx, DRx
43Y9849
R
N
7
Hinge L/R
45N3862
R
N
IdeaPad S9e and S10e
103
10.1-in. WSVGA TFT
Table 33. Parts list—10.1-in. WSVGA TFT
No.
FRU
FRU no.
RoHS
ID
CRU
ID
b - e See “Miscellaneous parts” on page 107.
104
1
LCD front bezel assembly, black for 10.1-in. WSVGA
45N4959
v 4068-CTO, 42x, 46x, 4Ax, 4Ex, 4Jx, 4Nx, 4Sx, 4Wx,
A2x, A3x, A4x, A5x, A6x, A7x, A8x, A9x, AAx, ABx,
ACx, ADx, AEx, AFx
v 4187-CTO, 39x, 3Ax, 3Dx, 3Hx, 3Jx, 52x, 55x, 58x, 5Bx,
5Ex, 5Hx, 5Lx, 5Px, ERx
R
N
1
LCD front bezel assembly, white for 10.1-in. WSVGA
45N5091
v 4068-CTO, 43x, 44x, 47x, 48x, 4Bx, 4Cx, 4Fx, 4Gx, 4Kx,
4Lx, 4Px, 4Qx, 4Tx, 4Ux, 4Xx, 4Yx, AGx, AHx, AJx
v 4187-CTO, 53x, 54x, 56x, 57x, 59x, 5Ax, 5Cx, 5Dx, 5Fx,
5Gx, 5Jx, 5Kx, 5Mx, 5Nx, 5Qx, 5Rx
R
N
2
LCD panel, 10.1-in. WSVGA
v 4068-CTO, 42x, 43x, 44x, 46x, 47x, 48x, 4Ax, 4Bx, 4Cx,
4Ex, 4Fx, 4Gx, 4Jx, 4Kx, 4Lx, 4Nx, 4Px, 4Qx, 4Sx, 4Tx,
4Ux, 4Wx, 4Xx, 4Yx, A2x, A3x, A4x, A5x, A6x, A7x,
A8x, A9x, AAx, ABx, ACx, ADx, AEx, AFx, AGx,
AHx, AJx
v 4187-CTO, 39x, 3Ax, 3Dx, 3Hx, 3Jx, 52x, 53x, 54x, 55x,
56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Fx, 5Gx,
5Hx, 5Jx, 5Kx, 5Lx, 5Mx ,5Nx, 5Px, 5Qx, 5Rx, ERx
42T0617
R
N
2
LCD panel, 10.1-in. WSVGA
v 4068-CTO, 42x, 43x, 44x, 46x, 47x, 48x, 4Ax, 4Bx, 4Cx,
4Ex, 4Fx, 4Gx, 4Jx, 4Kx, 4Lx, 4Nx, 4Px, 4Qx, 4Sx, 4Tx,
4Ux, 4Wx, 4Xx, 4Yx, A2x, A3x, A4x, A5x, A6x, A7x,
A8x, A9x, AAx, ABx, ACx, ADx, AEx, AFx, AGx,
AHx, AJx
v 4187-CTO, 39x, 3Ax, 3Dx, 3Hx, 3Jx, 52x, 53x, 54x, 55x,
56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Fx, 5Gx,
5Hx, 5Jx, 5Kx, 5Lx, 5Mx ,5Nx, 5Px, 5Qx, 5Rx, ERx
42T0619
R
N
2
LCD panel, 10.1-in. WSVGA
v 4068-CTO, 42x, 43x, 44x, 46x, 47x, 48x, 4Ax, 4Bx, 4Cx,
4Ex, 4Fx, 4Gx, 4Jx, 4Kx, 4Lx, 4Nx, 4Px, 4Qx, 4Sx, 4Tx,
4Ux, 4Wx, 4Xx, 4Yx, A2x, A3x, A4x, A5x, A6x, A7x,
A8x, A9x, AAx, ABx, ACx, ADx, AEx, AFx, AGx,
AHx, AJx
v 4187-CTO, 39x, 3Ax, 3Dx, 3Hx, 3Jx, 52x, 53x, 54x, 55x,
56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Fx, 5Gx,
5Hx, 5Jx, 5Kx, 5Lx, 5Mx ,5Nx, 5Px, 5Qx, 5Rx, ERx
42T0621
R
N
3
Integrated camera for 10.1-in. WSVGA
v 4068-CTO, 42x, 43x, 44x, 46x, 47x, 48x, 4Ax, 4Bx, 4Cx,
4Ex, 4Fx, 4Gx, 4Jx, 4Kx, 4Lx, 4Nx, 4Px, 4Qx, 4Sx, 4Tx,
4Ux, 4Wx, 4Xx, 4Yx, A2x, A3x, A4x, A5x, A6x, A7x,
A8x, A9x, AAx, ABx, ACx, ADx, AEx, AFx, AGx,
AHx, AJx
v 4187-CTO, 39x, 3Ax, 3Dx, 3Hx, 3Jx, 52x, 53x, 54x, 55x,
56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Fx, 5Gx,
5Hx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 5Px, 5Qx, 5Rx, ERx
42T4203
R
N
4
Camera cable
44C9901
R
N
IdeaPad S9e and S10e Hardware Maintenance Manual
Table 33. Parts list—10.1-in. WSVGA TFT (continued)
No.
FRU
FRU no.
RoHS
ID
CRU
ID
5
LCD rear cover assembly, dark silver with wireless LAN 45N3861
antenna
v 4068-CTO, A2x, A3x, A4x, A5x, A6x, A7x, A8x, A9x,
AAx, ABx, ACx, ADx, AEx, AFx
v 4187-CTO, 39x, 3Ax, 3Dx, 3Hx, 3Jx, ERx
R
N
5
LCD rear cover assembly, blue with wireless LAN
antenna
v 4068-CTO, AHx
v 4187-CTO
45N5092
R
N
5
LCD rear cover assembly, red with wireless LAN
antenna
v 4068-CTO, 44x, 48x, 4Cx, 4Gx, 4Lx, 4Qx, 4Ux, 4Yx
v 4187-CTO, 54x, 57x, 5Ax, 5Dx, 5Gx, 5Kx, 5Nx, 5Rx
45N5093
R
N
5
LCD rear cover assembly, pink with wireless LAN
antenna
v 4068-CTO, AJx
v 4187-CTO
45N5094
R
N
5
LCD rear cover assembly, white with wireless LAN
45N5095
antenna
v 4068-CTO, 43x, 47x, 4Bx, 4Fx, 4Kx, 4Px, 4Tx, 4Xx, AGx
v 4187-CTO, 53x, 56x, 59x, 5Cx, 5Fx, 5Jx, 5Mx, 5Qx
R
N
5
LCD rear cover assembly, black with wireless LAN
antenna
v 4068-CTO, 42x, 46x, 4Ax, 4Ex, 4Jx, 4Nx, 4Sx, 4Wx
v 4187-CTO, 52x, 55x, 58x, 5Bx, 5Ex, 5Hx, 5Lx, 5Px
45N5096
R
N
6
LCD cable assembly for 10.1-in. WSVGA
v 4068-CTO, 42x, 43x, 44x, 46x, 47x, 48x, 4Ax, 4Bx, 4Cx,
4Ex, 4Fx, 4Gx, 4Jx, 4Kx, 4Lx, 4Nx, 4Px, 4Qx, 4Sx, 4Tx,
4Ux, 4Wx, 4Xx, 4Yx, A2x, A3x, A4x, A5x, A6x, A7x,
A8x, A9x, AAx, ABx, ACx, ADx, AEx, AFx, AGx,
AHx, AJx
v 4187-CTO, 39x, 3Ax, 3Dx, 3Hx, 3Jx, 52x, 53x, 54x, 55x,
56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Fx, 5Gx,
5Hx, 5Jx, 5Kx, 5Lx, 5Mx ,5Nx, 5Px, 5Qx, 5Rx, ERx
44C9913
R
N
7
Hinge L/R
45N3862
R
N
IdeaPad S9e and S10e
105
Keyboard
Table 34. Parts list—Keyboard
106
Language
P/N (black) P/N (white) RoHS
ID
CRU
ID
Arabic
42T4166
42T4244
**
Belgian
42T4167
42T4245
Brazilian Portuguese
42T4194
42T4272
Bulgarian
42T4197
42T4275
Canadian French (058)
42T4165
42T4243
Canadian French (Acnor)
42T4164
42T4242
Czech
42T4168
42T4246
Danish
42T4169
42T4247
Dutch
42T4177
42T4255
Finnish, Swedish
42T4184
42T4262
French
42T4171
42T4249
German
42T4172
42T4250
Greek (U.S. English and Greek layout)
42T4173
42T4251
Hebrew
42T4175
42T4253
Hungarian
42T4174
42T4252
Icelandic
42T4195
42T4273
Italian
42T4176
42T4254
Japanese
42T4189
42T4267
Kazakhstan
42T4196
42T4242
Latin American Spanish
42T4192
42T4270
Norwegian
42T4178
42T4256
Polish
42T4179
42T4257
Portuguese
42T4180
42T4258
Russian
42T4181
42T4259
Slovak
42T4182
42T4260
Slovenian
42T4183
42T4261
Spanish
42T4170
42T4248
Swiss
42T4185
42T4263
Traditional Chinese
42T4190
42T4268
Turkish
42T4186
42T4264
U.K. English
42T4187
42T4265
U.S. English
42T4163
42T4241
U.S. English (International, with a Euro
symbol)
42T4188
42T4266
IdeaPad S9e and S10e Hardware Maintenance Manual
R
Miscellaneous parts
Table 35. Parts list—Miscellaneous parts
FRU
P/N
RoHS
ID
CRU
ID
45N3867
R
N
45N3863
R
N
Rubber cap kit:
v Rubber cap, Top, black
v Rubber cap, Bottom, black
v Rubber cap, Top, white
v Rubber cap, Bottom, white
v Rubber cap, Rear, dark silver
v Rubber cap, Rear, blue
v Rubber cap, Rear, red
v Rubber cap, Rear, pink
v Rubber cap, Rear, white
v Rubber cap, Rear, black
45N5143
R
N
Misc parts kit (dark sliver):
v (a) HDD door, dark silver
v ExpressCard dummy, dark silver
45N5098
R
N
45N5099
R
N
45N5100
R
N
45N5101
R
N
45N5102
R
N
Screw kit:
v M2 × 2.5
v M2 × 4.0
v M2 × 6.0
v M3 × 3.5
mm
mm
mm
mm
(silver), wafer-head (10)
(silver), wafer-head (25)
(black), wafer-head (15)
(silver), wafer-head (5)
Misc parts kit (common):
v (b) LCD bracket, Right
v (c) LCD bracket, Left
v (d) Hinge cap, Right
v (e) Hinge cap, Left
Note: Italicized letters in parentheses are references to the
exploded view in “LCD FRUs” on page 101.
Note: Italicized letters in parentheses are references to the
exploded view in “Overall” on page 96.
Misc parts kit (blue):
v (a) HDD door, blue
v ExpressCard dummy, blue
Note: Italicized letters in parentheses are references to the
exploded view in “Overall” on page 96.
Misc parts kit (red):
v (a) HDD door, red
v ExpressCard dummy, red
Note: Italicized letters in parentheses are references to the
exploded view in “Overall” on page 96.
Misc parts kit (pink):
v (a) HDD door, pink
v ExpressCard dummy, pink
Note: Italicized letters in parentheses are references to the
exploded view in “Overall” on page 96.
Misc parts kit (white):
v (a) HDD door, white
v ExpressCard dummy, white
Note: Italicized letters in parentheses are references to the
exploded view in “Overall” on page 96.
IdeaPad S9e and S10e
107
Table 35. Parts list—Miscellaneous parts (continued)
FRU
P/N
RoHS
ID
CRU
ID
Misc parts kit (black):
v (a) HDD door, painted black
v ExpressCard dummy, painted black
45N5115
R
N
45N5116
R
N
FRU
P/N
RoHS
ID
CRU
ID
2-pin (40 W, 20 V) adapter
42T4455
R
*
3-pin (40 W, 20 V) adapter
42T4449
R
*
Note: Italicized letters in parentheses are references to the
exploded view in “Overall” on page 96.
Misc parts kit (all black):
v (a) HDD door, material black
v ExpressCard dummy, material black
Note: Italicized letters in parentheses are references to the
exploded view in “Overall” on page 96.
AC adapters
Table 36. Parts list—AC adapters
108
IdeaPad S9e and S10e Hardware Maintenance Manual
Power cords
A IdeaPad power cord for a specific country or region is usually available only in
that country or region:
Table 37. Parts list—2-pin power cords
Region
P/N
Argentina
v models -CTO, xxY
42T5020
42T5105
Brazil
v models -CTO, xxP
42T5180
42T5183
Canada, U.S.
v models -CTO, xxF, xxL, xxS, xxU
42T5008
42T5093
Japan
v models -Exx, Jxx
42T5014
42T5099
RoHS
ID
CRU
ID
R
*
RoHS
ID
CRU
ID
R
*
Table 38. Parts list—3-pin power cords
Region
P/N
Australia, New Zealand
v models -CTO, xxG, xxM
42T5050
42T5135
Bangladesh, Sri Lanka, South Africa
v models -CTO, xxG
42T5056
42T5141
Canada, U.S.
v models -CTO, xxF, xxL, xxS, xxU
42T5004
42T5089
China (P.R.C.) (other than Hong Kong S.A.R.)
v models -xxC
42T5065
42T5150
Denmark
v models -CTO, xxG
42T5041
42T5126
European countries
v models -CTO, xxG
42T5029
42T5114
India
v models -CTO, xxG
42T5083
42T5168
Israel
v models -CTO, xxG
42T5062
42T5147
Italy
v models -CTO, xxG
42T5047
42T5132
Korea
v models -xxK
42T5077
42T5162
Switzerland
v models -CTO, xxG
42T5044
42T5129
Taiwan
v models -CTO, xxV
42T5071
42T5156
U.K., China (Hong Kong S.A.R.)
v models -CTO, xxB, xxG, xxH
42T5035
42T5120
IdeaPad S9e and S10e
109
Recovery discs
Windows XP Home DVDs for HDD
Windows XP Home for HDD is preinstalled as the operating system in the
following models:
v 4068-CTO, 23x, 27x, 29x, 2Bx, 35x, 36x, 38x, 39x, 42x, 43x, 44x, 4Sx, 4Tx, 4Ux,
4Wx, 4Xx, 4Yx, A3x, A8x, AAx, AFx, AGx, AHx, AJx
v 4187-CTO, 29x, 33x, 34x, 39x, 3Ax, 3Hx, 42x, 43x, 48x, 49x, 52x, 53x, 54x, 5Lx,
5Mx, 5Nx, 5Px, 5Qx, 5Rx
Table 39. Parts list—Windows XP Home DVDs for HDD
110
Language
P/N
RoHS
ID
CRU
ID
Arabic
46V2802
R
*
Brazilian Portuguese
46V2803
Czech
46V2807
Danish
46V2808
Dutch
46V2809
English
46V2824
Finnish
46V2810
French
46V2811
German
46V2812
Greek
46V2813
Hebrew
46V2814
Hungarian
46V2815
Italian
46V2816
Japanese
46V2817
Korean
46V2818
Norwegian
46V2819
Polish
46V2820
Russian
46V2826
Simplified Chinese
46V2804
Spanish
46V2821
Swedish
46V2822
Traditional Chinese
46V2806
Traditional Chinese (Hong Kong S.A.R.)
46V2805
Turkish
46V2823
IdeaPad S9e and S10e Hardware Maintenance Manual
Windows XP Home DVDs for SSD
Windows XP Homel for SSD is preinstalled as the operating system in the
following models:
v 4068-CTO, 28x, 3Ex, 3Fx, 4Nx, 4Px, 4Qx, A4x, ADx
v 4187-CTO, 4Ex, 4Fx, 5Hx, 5Jx, 5Kx
Table 40. Parts list—Windows XP Home DVDs for SSD
Language
P/N
RoHS
ID
CRU
ID
Arabic
46V2603
R
*
Brazilian Portuguese
46V2604
Czech
46V2608
Danish
46V2609
Dutch
46V2610
English
46V2625
Finnish
46V2611
French
46V2612
German
46V2613
Greek
46V2614
Hebrew
46V2615
Hungarian
46V2616
Italian
46V2617
Japanese
46V2618
Korean
46V2619
Norwegian
46V2620
Polish
46V2621
Russian
46V2627
Simplified Chinese
46V2605
Spanish
46V2622
Swedish
46V2623
Traditional Chinese
46V2607
Traditional Chinese (Hong Kong S.A.R.)
46V2606
Turkish
46V2624
IdeaPad S9e and S10e
111
SUSE Linux Enterprise Desktop 10 DVDs for HDD
SUSE Linux Enterprise Desktop 10 for HDD is preinstalled as the operating system
in the following models:
v 4068-CTO, 24x, 2Ax, 3Bx, 3Cx, 4Ax, 4Bx, 4Cx, 4Ex, 4Fx, 4Gx, 4Jx, 4Kx, 4Lx, A5x,
A7x, A9x, ABx, AEx
v 4187-CTO, 27x, 37x, 4Bx, 4Cx, 3Dx, 3Jx, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Fx,
5Gx
Table 41. Parts list— SUSE Linux Enterprise Desktop 10 DVDs for HDD
112
Language
P/N
RoHS
ID
CRU
ID
All languages
46V2765
R
*
IdeaPad S9e and S10e Hardware Maintenance Manual
SUSE Linux Enterprise Desktop 10 DVDs for SSD
SUSE Linux Enterprise Desktop 10 for SSD is preinstalled as the operating system
in the following models:
v 4068-CTO, 22x, 32x, 33x, 46x, 47x, 48x, A2x, A6x, ACx
v 4187-CTO, 32x, 45x, 46x, 55x, 56x, 57x, DRx, ERx
Table 42. Parts list— SUSE Linux Enterprise Desktop 10 DVDs for SSD
Language
P/N
RoHS
ID
CRU
ID
Brazilian Portuguese, English, French, German, Italian,
Spanish
46V2762
R
*
Czech, Danish, Dutch, English, Finnish, Greek, Hungarian,
Slovenian, Swedish, Polish, Russian, Turkish
46V2763
Japanese, Korean, Simplified Chinese, Traditional Chinese,
Traditional Chinese (Hong Kong S.A.R.)
46V2764
IdeaPad S9e and S10e
113
Common service tools
Table 43. Parts list—Common service tools
Tool
P/N
Screwdriver kit
95F3598
1/4″ drive spinner handle
1650840
1/4″ Sq. to 1/4″ hex torx adapter
93F2838
TR7-TR-10 tamper resistant torx bits
00P6967
Removal tool antenna RF connector
08K7159
USB 2.0 CD-RW/DVD-ROM combo drive II
40Y8687
USB cable
40Y8704
USB floppy diskette drive
05K9283
USB floppy diskette drive tool kit
27L3452
Test card for integrated Smart Card
42W7820
CE Utility for IdeaPad S9e and S10e
—
Note: Download the file from the following Web site: http://www.lenovo.com/
spm
114
IdeaPad S9e and S10e Hardware Maintenance Manual
Notices
Lenovo may not offer the products, services, or features discussed in this
document in all countries. Consult your local Lenovo representative for
information on the products and services currently available in your area. Any
reference to a Lenovo product, program, or service is not intended to state or
imply that only that Lenovo product, program, or service may be used. Any
functionally equivalent product, program, or service that does not infringe any
Lenovo intellectual property right may be used instead. However, it is the user’s
responsibility to evaluate and verify the operation of any other product, program,
or service.
Lenovo may have patents or pending patent applications covering subject matter
described in this document. The furnishing of this document does not give you
any license to these patents. You can send license inquiries, in writing, to:
Lenovo (United States), Inc.
1009 Think Place - Building One
Morrisville, NC 27560
U.S.A.
Attention: Lenovo Director of Licensing
LENOVO GROUP LTD. PROVIDES THIS PUBLICATION “AS IS” WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some
jurisdictions do not allow disclaimer of express or implied warranties in certain
transactions, therefore, this statement may not apply to you.
This information could include technical inaccuracies or typographical errors.
Changes are periodically made to the information herein; these changes will be
incorporated in new editions of the publication. Lenovo may make improvements
and/or changes in the product(s) and/or the program(s) described in this
publication at any time without notice.
The products described in this document are not intended for use in implantation
or other life support applications where malfunction may result in injury or death
to persons. The information contained in this document does not affect or change
Lenovo product specifications or warranties. Nothing in this document shall
operate as an express or implied license or indemnity under the intellectual
property rights of Lenovo or third parties. All information contained in this
document was obtained in specific environments and is presented as an
illustration. The result obtained in other operating environments may vary.
Lenovo may use or distribute any of the information you supply in any way it
believes appropriate without incurring any obligation to you.
Any references in this publication to non-Lenovo Web sites are provided for
convenience only and do not in any manner serve as an endorsement of those Web
sites. The materials at those Web sites are not part of the materials for this Lenovo
product, and use of those Web sites is at your own risk.
Any performance data contained herein was determined in a controlled
environment. Therefore, the result obtained in other operating environments may
© Copyright Lenovo 2008
115
vary significantly. Some measurements may have been made on development-level
systems and there is no guarantee that these measurements will be the same on
generally available systems. Furthermore, some measurements may have been
estimated through extrapolation. Actual results may vary. Users of this document
should verify the applicable data for their specific environment.
Trademarks
The following terms are trademarks of Lenovo in the United States, other countries
or both:
Lenovo®
IdeaPad
The following terms are trademarks of the International Business Machines
Corporation in the United States, other countries, or both:
IBM® (used under license)
The following terms are trademarks of Microsoft Corporation in the United States,
other countries, or both:
Windows®
The following are trademarks of Intel Corporation or its subsidiaries in the United
States, other countries, or both:
Intel®
Intel® ATOMTM
Other company, product, or service names may be the trademarks or service marks
of others.
116
IdeaPad S9e and S10e Hardware Maintenance Manual
Part Number: 45N3684
(1P) P/N: 45N3684
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement