Sharp MX-M620U Specifications

MX-M550U/MX-M620U/MX-M700U/MX-M550N/MX-M620N/MX-M700N
OPERATION MANUAL (for general information and copier operation)
NA
KS1
CZZ
dragonII_copy_sec.book
1 ページ
２００６年１０月１８日　水曜日　午後７時３９分
MODEL
MX-M550U
MX-M620U
MX-M700U
MX-M550N
MX-M620N
MX-M700N
DIGITAL MULTIFUNCTIONAL
SYSTEM
OPERATION MANUAL
(for general information and copier operation)
Page
PART 1: GENERAL INFORMATION
• BEFORE USING
THE PRODUCT
• MANAGING THE MACHINE
• PERIPHERAL DEVICES
1-1
2-1
3-1
PART 2: COPIER OPERATION
• MAKING COPIES
• CONVENIENT COPY
FUNCTIONS
• MACHINE MAINTENANCE
(FOR COPYING)
• DOCUMENT FILING
FUNCTION
• SPECIFICATIONS
4-1
5-1
6-1
7-1
8-1
Be sure to become thoroughly familiar with this manual to
gain the maximum benefit from the product.
Before installing this product, be sure to read the
installation requirements and cautions sections.
Be sure to keep all operation manuals handy for reference
including this manual, the "Operation manual (for general
information and copier operation)" and operation manuals
for any optional equipment which has been installed.
dragon_cover2.fm
1 ページ
２００６年１１月２９日　水曜日　午後８時２５分
Each instruction also covers the optional units used with these products.
The power switch positions are marked " I " to indicate power "ON" and " " to indicate stand-by.
In the stand-by position, power is being supplied to a drying heater within the paper tray and sensor system in the
printer.
Caution:
For complete electrical disconnection, pull out the main plug.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
FOR YOUR RECORDS ...
To protect against loss or theft, record and retain for reference the machine's serial number located on the back
of the unit.
Model Number
Serial Number
Date of Purchase
Place of Purchase
Authorized Sharp Printer
Service Department Number
WARNING:
FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved
by the manufacturer could void the user's authority to operate this equipment.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
●
●
●
●
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Shielded interface cables must be used with this equipment to maintain compliance with EMC regulations.
Model Number: MX-M550U/MX-M550N/MX-M620U/MX-M620N/MX-M700U/MX-M700N
MX-M550U J/MX-M620U J/MX-M700U J
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undersired operation.
Responsible Party: SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430
TEL:1-800-BE-SHARP
dragonII_copy_sec.book
2 ページ
２００６年１０月１８日　水曜日　午後７時３９分
The Environmental Choice Program guidelines are applied to the products only in Canada. The
products that meet the Environmental Choice Program guidelines carry the logo shown to the left. The
products without the logo may not meet the Environmental Choice Program guidelines.
Trademark acknowledgments
The following trademarks and registered trademarks are used in conjunction with the machine and its peripheral devices and
accessories.
• Microsoft®, Windows®, Windows® 98, Windows® Me, Windows NT® 4.0, Windows® 2000, Windows® XP, Windows® Server
2003 and Internet Explorer® are registered trademarks or trademarks of Microsoft Corporation in the U.S.A. and other
countries.
• PostScript is a registered trademark of Adobe Systems Incorporated.
• Macintosh, Mac OS, AppleTalk, EtherTalk, LaserWriter, and Safari are registered trademarks or trademarks of Apple
Computer, Inc.
• Netscape Navigator is a trademark of Netscape Communications Corporation.
• Adobe, the Adobe logo, Acrobat, the Adobe PDF logo, and Reader are registered trademarks or trademarks of Adobe
Systems Incorporated in the United States and other countries.
• PCL is a registered trademark of the Hewlett-Packard Company.
• IBM, PC/AT, and PowerPC are trademarks of International Business Machines Corporation.
• Sharpdesk is a trademark of Sharp Corporation.
• All other trademarks and copyrights are the property of their respective owners.
Candid and Taffy are trademarks of Monotype Imaging, Inc. registered in the United States Patent and Trademark Office and may
be registered in certain jurisdictions. CG Omega, CG Times, Garamond Antiqua, Garamond Halbfett, Garamond Kursiv,
Garamond and Halbfett Kursiv are trademarks of Monotype Imaging, Inc. and may be registered in certain jurisdictions. Albertus,
Arial, Coronet, Gill Sans, Joanna and Times New Roman are trademarks of The Monotype Corporation registered in the United
States Patent and Trademark Office and may be registered in certain jurisdictions. Avant Garde, ITC Bookman, Lubalin Graph,
Mona Lisa, Zapf Chancery and Zapf Dingbats are trademarks of International Typeface Corporation registered in the United
States Patent and Trademark Office and may be registered in certain jurisdictions. Clarendon, Eurostile, Helvetica, Optima,
Palatino, Stempel Garamond, Times and Univers are trademarks of Heidelberger Druckmaschinen AG, which may be registered
in certain jurisdictions, exclusively licensed through Linotype Library GmbH, a wholly owned subsidiary of Heidelberger
Druckmaschinen AG. Apple Chancery, Chicago, Geneva, Monaco and New York are trademarks of Apple Computer Inc. and may
be registered in certain jurisdictions. HGGothicB, HGMinchoL, HGPGothicB and HGPMinchoL are trademarks of Ricoh Company,
Ltd. and may be registered in some jurisdictions. Wingdings is a registered trademark of Microsoft Corporation in the United States
and other countries. Marigold and Oxford are trademarks of Arthur Baker and may be registered in some jurisdictions. Antique
Olive is a trademark of Marcel Olive and may be registered in certain jurisdictions. Hoefler Text is a trademark of Johnathan
Hoefler and may be registered in some jurisdictions. ITC is a trademark of International Typeface Corporation registered in the
United States Patent and Trademark Office and may be registered in certain jurisdictions. Agfa is a trademark of the Agfa-Gevaert
Group and may be registered in certain jurisdictions. Intellifont, MicroType and UFST are trademarks of Monotype Imaging, Inc.
registered in the United States Patent and Trademark Office and may be registered in certain jurisdictions. Macintosh and
TrueType are trademarks of Apple Computer Inc. registered in the United States Patent and Trademark Office and other countries.
PostScript is a trademark of Adobe Systems Incorporated and may be registered in some jurisdictions. HP, PCL, FontSmart and
LaserJet are trademarks of Hewlett-Packard Company and may be registered in some jurisdictions. The Type 1 processor resident
in Monotype Imaging's UFST product is under license from Electronics For Imaging, Inc. All other trademarks are the property of
their respective owners.
dragonII_copy_sec.book
3 ページ
２００６年１０月１８日　水曜日　午後７時３９分
dragonII_copy_sec.book
1 ページ
２００６年１０月１８日　水曜日　午後７時３９分
Part 1: General Information
dragonII_copy_sec.book
2 ページ
２００６年１０月１８日　水曜日　午後７時３９分
dragon_00.fm
1 ページ
２００６年１０月２０日　金曜日　午前１１時４８分
NOTES
● Considerable care has been taken in preparing this manual. If you have any comments or concerns about the
manual, please contact your nearest SHARP Service Department.
● This product has undergone strict quality control and inspection procedures. In the unlikely event that a defect
or other problem is discovered, please contact your dealer or nearest SHARP Service Department.
● Aside from instances provided for by law, SHARP is not responsible for failures occurring during use of the
product or its options, or failures due to incorrect operation of the product and its options, or other failures, or for
any damage that occurs due to use of the product.
Warranty
While every effort has been made to make this document as accurate and helpful as possible, SHARP Corporation makes
no warranty of any kind with regard to its content. All information included herein is subject to change without notice. SHARP
is not responsible for any loss or damages, direct or indirect, arising from or related to the use of this operation manual.
© Copyright SHARP Corporation 2006. All rights reserved. Reproduction, adaptation or translation without prior
written permission is prohibited, except as allowed under copyright laws.
The display screens, messages, and key names shown in the manual may differ from those on the actual machine
due to product improvements and modifications.
OPERATION MANUALS
The following operation manuals are provided for the machine. Please read the appropriate manuals as needed for
the features you wish to learn about.
● Operation manual (for general information and copier operation) (this manual)
The first half of this manual provides general information about the machine, including safety information, loading
paper, removing misfeeds, and regular maintenance.
The second half of the manual explains how to use the copy and document filing functions.
● Administrator settings guide
The administrator settings are used by the administrator of the machine to configure functions to meet the needs
of your workplace.
This guide explains administrator settings for machine management, copying, and document filing. Administrator
settings for the fax, printer, network scanner and Internet fax functions are explained in the manuals for those
functions.
● Software setup guide
This manual mainly explains how to install and configure the software that allows the machine to be used as a
printer.
● Operation manual (for printer)*1
This manual explains the procedures for using the machine as a printer.
● Operation manual (for image send)*1
This manual explains the procedures for using the image send feature of the machine, including the network
scanner and Internet fax functions.
To use the network scanner function, the network function of the machine must be in a useable state*2 and the
network scanner expansion kit must be installed.
To use the Internet fax function, the network function of the machine must be in a useable state*2 and the network
scanner expansion kit and the Internet fax expansion kit must be installed.
*1 The Operation manual (for printer) and the Operation manual (for image send) are provided as PDF files in the
CD-ROM.
These manuals are not provided as printed manuals.
*2 On the MX-M550U/M620U/M700U, the network expansion kit is required.
0-1
dragonII_copy_sec.book
2 ページ
２００６年１０月１８日　水曜日　午後７時３９分
INSTALLATION REQUIREMENTS
Improper installation may damage this product. Please note the following during initial installation and whenever the
machine is moved.
1.The machine should be installed near an
accessible power outlet for easy connection.
2.Be sure to connect the power cord only to a
power outlet that meets the specified voltage and
current requirements. Also make certain the
outlet is properly grounded.
●For the power supply requirements, see the
name plate on the back of the main unit.
3.Do not install your machine in areas that are:
●damp, humid, or very dusty
●exposed to direct sunlight
●poorly ventilated
●subject to extreme temperature or humidity
changes, e.g., near an air conditioner or heater.
4.Be sure to allow the required space around the
machine for servicing and proper ventilation.
11-13/16"
(30cm)
6-1/8"
(15cm)
23-5/8"
(60cm)
A small amount of ozone is produced within the printer during operation. The emission level is insufficient to cause
any health hazard.
NOTE:
The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m3) calculated as an 8 hr. timeweighted average concentration.
However, since the small amount that is emitted may have an objectionable odor, it is advisable to place the copier
in a ventilated area.
0-2
dragon_00.fm
3 ページ
２００６年１１月２９日　水曜日　午後８時２６分
CAUTIONS
1.Do not touch the photoconductive drum. Scratches or smudges on the
drum will cause dirty prints.
2.The fusing unit is extremely hot. Exercise care in this area.
3.Do not look directly at the light source. Doing so may damage your
eyes.
Fusing unit
4.Four adjusters are provided on all optional stand/paper drawer units.
These adjusters should be lowered until they contact the floor.
When moving the machine with the optional stand/paper drawer, be
sure to raise the adjusters. Also, unlock the two casters at the front of
the optional stand/paper drawer. After moving the machine, lower the
four adjusters until they reach the floor and lock the two casters.
5.Do not make any modifications to this machine. Doing so may result in
personal injury or damage to the machine.
6.Since this machine is heavy, it is recommended that it be moved by
more than one person to prevent injury.
Adjuster
7.When connecting this machine to a computer, be sure to first turn both
the computer and the machine off.
Lock
8.Do not make copies of anything which is prohibited from copying by law.
The following items are normally prohibited from printing by national
law. Other items may be prohibited by local law.
● Money ● Stamps ● Bonds ● Stocks
● Bank drafts ● Checks ● Passports ● Driver's licenses
Release
Caution:
This connector (A) is only intended for service purposes.
Any connection to this terminal may cause malfunctions of the machine.
Instruction for service technician:
The cable length for the service terminal has to be less than 118" (3m).
(A)
The machine includes the document filing function, which stores document image data on the machine's hard disk.
Stored documents can be called up and printed or transmitted as needed. If a hard disk failure occurs, it will no
longer be possible to call up the stored document data. To prevent the loss of important documents in the unlikely
event of a hard disk failure, keep the originals of important documents or store the original data elsewhere.
With the exception of instances provided for by law, Sharp Corporation bears no responsibility for any damages
or loss due to the loss of stored document data.
"BATTERY DISPOSAL"
THIS PRODUCT CONTAINS A LITHIUM PRIMARY MEMORY BACK-UP BATTERY THAT MUST BE
DISPOSED OF PROPERLY. PLEASE CONTACT YOUR LOCAL SHARP DEALER OR AUTHORIZED SERVICE
REPRESENTATIVE FOR ASSISTANCE IN DISPOSING OF THIS BATTERY.
This product utilizes tin-lead solder, and a fluorescent lamp containing a small amount of mercury.
Disposal of these materials may be regulated due to environmental considerations.
For disposal or recycling information, please contact your local authorities or the Electronics Industries Alliance:
www.eia.org
0-3
dragon_00.fm
4 ページ
２００６年１１月２９日　水曜日　午後８時３６分
CAUTIONS
Laser Information
Wave length
Pulse times
Output power
785 nm
+10 nm
-15 nm
North America:
55 cpm / 62 cpm model: (3.1 µs ± 3.1 ns)/7 mm
70 cpm model: (2.7 µs ± 2.7 ns)/7 mm
Europe:
55 cpm / 62 cpm model: (3.7 µs ± 3.7 ns)/7 mm
70 cpm model: (3.2 µs ± 3.2 ns)/7 mm
Max 0.8 mW
At the production line, the output power of the scanner unit is adjusted to 0.8 MILLIWATT PLUS 10 % and is maintained
constant by the operation of the Automatic Power Control (APC).
Caution
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous
radiation exposure.
For North America:
SAFETY PRECAUTIONS
This Digital Equipment is rated Class 1 and complies with 21 CFR 1040.10 and 1040.11 of the CDRH standards. This
means that the equipment does not produce hazardous laser radiation. For your safety, observe the precautions below.
● Do not remove the cabinet, operation panel or any other covers.
● The equipment's exterior covers contain several safety interlock switches. Do not bypass any safety interlock by
inserting wedges or other items into switch slots.
This product utilizes a CR coin Lithium battery which contains a Perchlorate material. Special handling for this material may
apply, California residents, See www.dtsc.ca.gov/hazardouswaste/perchlorate/
Others, consult local environmental officers.
For Europe:
CAUTION
INVISIBLE LASER RADIATION
WHEN OPEN INTERLOCKS
DEFEATED. AVOID EXPOSURE
TO BEAM.
CLASS 1 LASER PRODUCT
LASER KLASSE 1
VAROITUS!
LAITTEEN KÄYTTÄMINEN
MUULLA KUIN TÄSSÄ
KÄYTTÖOHJEESSA
MAINITULLA TAVALLA SAATTAA
ALTISTAA KÄYTTÄJÄN
TURVALLISUUSLUOKAN 1
YLITTÄVÄLLE
NÄKYMÄTTÖMÄLLE
LASERSÄTEILYLLE.
VORSICHT
UNSICHTBARE
LASERSTRAHLUNG WENN
ABDECKUNG GEÖFFNET UND
SICHERHEITSVERRIEGELUNG
ÜBERBRÜCKT. NICHT DEM
STRAHL AUSSETZEN.
LUOKAN 1 LASERLAITE
VARNING
OM APPARATEN ANVÄNDS PÅ
ANNAT SÄTT ÄN I DENNA
BRUKSANVISNING
SPECIFICERATS, KAN
ANVÄNDAREN UTSÄTTAS FÖR
OSYNLIG LASERSTRÅLNING,
SOM ÖVERSKRIDER GRÄNSEN
FÖR LASERKLASS 1.
ADVARSEL
USYNLIG LASERSTRÅLNING
VED ÅBNING, NÅR
SIKKERHEDSBRYDERE ER
UDE AF FUNKTION. UNDGÅ
UDSAETTELSE FOR
STRÅLNING.
KLASS 1 LASERAPPARAT
LASER KLASSE 1
Laserstrahl
0-4
CAUTION
VORSICHT
ADVARSEL
ADVERSEL
VARNING
VARO!
INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED.
AVOID EXPOSURE TO BEAM.
CLASS 1
LASER PRODUCT
UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET UND
SICHERHEITSVERRIEGELUNG ÜBERERÜCKT. NICHT DEM STRAHL AUSSETZEN.
USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAFBRYDERE ER
UDE AF FUNKTION. UNDGÅ UDSAETTELSE FOR STRÅLNING.
USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES OG SIKKERHEDSLÅS BRYTES.
UNNGÅ EKSPONERING FOR STRÅLEN.
OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRRAR ÄR
URKOPPLADE. STRÅLEN ÄR FARLIG. BETRAKTA EJ STRÅLEN.
AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄKYMÄTÖNTÄ
LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
dragon_00.fm
5 ページ
２００６年１０月１８日　水曜日　午後８時２７分
CONTENTS
Page
OPERATION MANUALS .............................................. 0-1
INSTALLATION REQUIREMENTS............................... 0-2
CAUTIONS................................................................... 0-3
● Laser Information ................................................. 0-4
CONTENTS ................................................................. 0-5
CHAPTER 1
BEFORE USING THE PRODUCT
INTRODUCTION.......................................................... 1-2
MAIN FEATURES ........................................................ 1-3
PART NAMES AND FUNCTIONS................................ 1-10
● Exterior................................................................. 1-10
● Interior .................................................................. 1-11
● Operation panel.................................................... 1-13
● Touch panel .......................................................... 1-14
TURNING THE POWER ON AND OFF ....................... 1-17
AUDITING MODE ........................................................ 1-18
● Using the machine when the auditing mode is
enabled................................................................. 1-18
CHAPTER 2
MANAGING THE MACHINE
LOADING PAPER ........................................................ 2-2
● Identifying the trays .............................................. 2-2
● Loading paper in paper tray 1 - tray 2 .................. 2-2
● Changing the paper size in paper tray 1 - tray 2 .. 2-3
● Loading paper in paper tray 3 .............................. 2-5
● Changing the paper size in paper tray 3 .............. 2-5
● Changing the paper size in paper tray 4 .............. 2-6
● Loading paper in paper tray 5 (optional large
capacity tray AR-LC6) ..................................................2-7
● Loading paper in paper tray 5 (optional large
capacity tray AR-LC7) ..................................................2-8
● Loading paper in the bypass tray ......................... 2-10
● Specifications of paper trays (Types and sizes of
paper that can be used in the trays)..................... 2-12
● Setting the paper type and paper size.................. 2-14
● Setting the paper size when a special size is
loaded .................................................................. 2-17
SYSTEM SETTINGS ................................................... 2-18
● General procedure for system settings ................ 2-18
● About the settings ................................................ 2-20
REPLACING THE TONER CARTRIDGES .................. 2-21
STORAGE OF SUPPLIES ........................................... 2-22
MISFEED REMOVAL ................................................... 2-23
● Misfeed removal guidance.................................... 2-23
● Misfeed in the transport area, fusing area, and
exit area................................................................ 2-24
● Misfeed in the duplex unit..................................... 2-25
● Misfeed in the paper feed area............................. 2-26
REMOVING AN ORIGINAL MISFEED......................... 2-31
● Removing a misfed original from the automatic
document feeder .................................................. 2-31
TROUBLESHOOTING ................................................. 2-32
CHAPTER 3
PERIPHERAL DEVICES
FINISHER AND SADDLE STITCH FINISHER .............3-2
● Part names ...........................................................3-2
● Specifications .......................................................3-2
● Finishing methods ................................................3-4
● Finishing modes and finisher functions ................3-6
● Staple cartridge replacement and staple jam
removal .................................................................3-7
● Removing a misfeed .............................................3-11
● Troubleshooting finisher/saddle stitch finisher
problems ...............................................................3-13
INSERTER ...................................................................3-14
● Part names ...........................................................3-14
● Specifications .......................................................3-14
● Loading paper.......................................................3-15
● Manual operation of the inserter...........................3-15
● Misfeed removal ...................................................3-17
● Troubleshooting inserter problems .......................3-18
SHARP OSA.................................................................3-19
APPLICATION COMMUNICATION MODULE (MXAMX2)...........................................................................3-19
● Standard application setup ...................................3-19
● Selecting a standard application...........................3-19
● Operation in OSA mode .......................................3-20
EXTERNAL ACCOUNT MODULE (MX-AMX3)............3-21
● External account application setup.......................3-21
● Operation in external account mode.....................3-21
CHAPTER 4
MAKING COPIES
AUTOMATIC DOCUMENT FEEDER............................4-2
● Acceptable originals .............................................4-2
PLACING ORIGINALS .................................................4-3
CHECKING THE SIZE OF A PLACED ORIGINAL.......4-5
● Manually setting the scanning size .......................4-5
STORING, DELETING, AND USING ORIGINAL
SIZES ...........................................................................4-6
● Storing or deleting an original size .......................4-6
NORMAL COPYING.....................................................4-7
● Making copies with the automatic document
feeding function ....................................................4-7
● Automatic two-sided copying using the automatic
document feeding function....................................4-10
● Copying from the document glass ........................4-11
● Automatic two-sided copying from the document
glass .....................................................................4-13
ADJUSTING THE EXPOSURE ....................................4-14
REDUCTION/ENLARGEMENT/ZOOM ........................4-15
● Automatic selection (auto image) .........................4-15
● Manual selection (preset copy ratios/zoom) .........4-16
● XY ZOOM .............................................................4-18
SPECIAL PAPERS .......................................................4-20
0-5
dragonII_copy_sec.book
6 ページ
２００６年１０月１８日　水曜日　午後７時３９分
CONTENTS
CHAPTER 5
CONVENIENT COPY FUNCTIONS
CHAPTER 8
SPECIFICATIONS
SPECIAL MODES ........................................................5-2
● General procedure for using special functions .....5-2
● Margin shift ...........................................................5-3
● Erase ....................................................................5-4
● Dual page copy.....................................................5-5
● Pamphlet copy ......................................................5-6
● Job build ...............................................................5-8
● Tandem copy ........................................................5-10
● Covers/inserts.......................................................5-12
● Transparency film with insert sheets ....................5-23
● Multi shot ..............................................................5-24
● Book copy.............................................................5-26
● Tab copy ...............................................................5-27
● Card shot ................................................................. 5-29
● Mirror image .........................................................5-31
● B/W reverse ..........................................................5-31
● Print menu ............................................................5-32
STORING,
USING
AND
DELETING
JOB
PROGRAMS.................................................................5-44
● Storing a job program ...........................................5-44
● Calling up a job program ......................................5-45
● Deleting a stored job program ..............................5-45
INTERRUPTING A COPY RUN ...................................5-46
SPECIFICATIONS ....................................................... 8-2
INDEX.......................................................................... 8-4
CHAPTER 6
MACHINE MAINTENANCE (FOR
COPYING)
USER MAINTENANCE ................................................6-2
● Cleaning the document glass and the automatic
document feeder...................................................6-2
TROUBLESHOOTING..................................................6-3
CHAPTER 7
DOCUMENT FILING FUNCTION
OVERVIEW ..................................................................7-2
● Document filing function .......................................7-2
TO USE THE DOCUMENT FILING FUNCTION ..........7-4
● A look at the operation panel................................7-4
● Saving files ...........................................................7-4
● Main screen of document filing.............................7-5
● Document filing icons ...........................................7-5
SAVING A DOCUMENT IMAGE FILE..........................7-6
● Quick File..............................................................7-6
● Filing .....................................................................7-7
● Print jobs ..............................................................7-9
● Scan Save ............................................................7-10
CALLING UP AND USING A FILE ...............................7-13
● Searching for and calling up a saved file .............. 7-13
● Calling up and using a saved file ..........................7-15
SYSTEM SETTINGS....................................................7-24
● Creating, editing, and deleting user names and
folders...................................................................7-24
ENTERING CHARACTERS .........................................7-29
TROUBLESHOOTING..................................................7-31
0-6
dragonII_copy_sec.book
1 ページ
２００６年１０月１８日　水曜日　午後７時３９分
CHAPTER 1
BEFORE USING THE
PRODUCT
This chapter contains basic information that should be read before using
the product.
Page
INTRODUCTION..................................................................................... 1-2
MAIN FEATURES ................................................................................... 1-3
PART NAMES AND FUNCTIONS........................................................... 1-10
● Exterior............................................................................................ 1-10
● Interior ............................................................................................. 1-11
● Operation panel............................................................................... 1-13
● Touch panel..................................................................................... 1-14
TURNING THE POWER ON AND OFF.................................................. 1-17
AUDITING MODE ................................................................................... 1-18
● Using the machine when the auditing mode is enabled.................. 1-18
1-1
dragonII_copy_sec.book
2 ページ
２００６年１０月１８日　水曜日　午後７時３９分
INTRODUCTION
Thank you for purchasing a SHARP digital multifunction copier.
Please read this manual before using the machine. In particular, be sure to read "INSTALLATION REQUIREMENTS"
before using the machine.
Please keep this manual close at hand for reference whenever necessary.
This manual provides general information on using the machine, such as routine maintenance and how to load paper
and remove misfeeds. It also explains how to use the copier and document filing functions.
Separate manuals have been provided for the fax function, printer function, and network scanner function.
■ Original and paper sizes
This machine allows use of standard sizes in both the inch and AB systems.
These are shown in the tables below.
Sizes in the inch system
Sizes in the AB system
11" x 17" (LEDGER)
A3
8-1/2" x 14" (LEGAL)
B4
8-1/2" x 13" (FOOLSCAP)
A4
8-1/2" x 11" (LETTER)
B5
7-1/4" x 10-1/2" (EXECUTIVE)
A5
5-1/2" x 8-1/2" (INVOICE)
■ The meaning of "R" in original and paper size indications
Some original and paper sizes can be placed in either the portrait or landscape orientations. To differentiate
between landscape and portrait, the landscape orientation size indication will contain an "R". These are indicated
as 8-1/2" x 11"R, 5-1/2" x 8-1/2"R, A4R, B5R, etc. Sizes that can be placed only in the landscape orientation (11"
x 17", 8-1/2" x 14", 8-1/2" x 13", A3, B4) do not contain the "R" in their size indication.
Size indication
with "R"
1-2
Landscape
orientation
Size indication
without "R"
Portrait orientation
dragonII_copy_sec.book
3 ページ
２００６年１０月１８日　水曜日　午後７時３９分
MAIN FEATURES
The digital multifunction copier is capable of performing a variety of functions. This page shows features related to
the copy function.
● Job programs
See page 1-6
● Sort mode
See page 1-3
● Mirror Image
See page 1-6
● Group mode
See page 1-3
● B/W Reverse
See page 1-6
● 2-sided Copy
See page 1-3
● Date print
See page 1-6
● Exposure Adjustments
See page 1-3
● Stamp
See page 1-7
● Reduction/Enlargement
See page 1-4
● Page numbering
See page 1-7
● XY Zoom
See page 1-4
● Text
See page 1-7
● Margin Shift
See page 1-4
● Interrupting a copy run
See page 1-7
● Erase
See page 1-4
● Offset mode
See page 1-7
● Dual Page Copy
See page 1-4
● Pamphlet Copy
See page 1-4
(When the Finisher or Saddle stitch finisher is installed.)
● Job Build
See page 1-5
● Staple sort mode
See page 1-7
● Tandem Copy
See page 1-5
(When the Finisher or Saddle stitch finisher is installed.)
(When using the MX-M550U, MX-M620U, or
● Saddle stitch
See page 1-8
MX-M700U, the network expansion kit is required.)
(When the Saddle stitch finisher is installed.)
● Covers/inserts
See page 1-5
● Hole punching
See page 1-8
● Transparency Insert
See page 1-5
(When the Punch Module is installed.)
● Multi Shot
See page 1-5
● Inserter mode
See page 1-8
● Book Copy
See page 1-5
(When the Inserter is installed.)
● Tab Copy
See page 1-6
● Document filing function
See page 1-8
● Card Shot
See page 1-6
Sort
See page 4-9
Copies can be collated.
Original
2-sided Copy
See pages 4-10, 4-13
Copy onto both sides of the paper using the document
glass or the automatic document feeder.
Group
Copy
Original
Copy
See page 4-9
Copies can be grouped by page.
Exposure Adjustments
The desired image type for the original can be
selected.
Text
Original
See page 4-14
Text/Photo
Photo
Copy
Resolution
ABCDE
ABCDE
Lighter
Darker
Exposure
1-3
1
dragonII_copy_sec.book
4 ページ
２００６年１０月１８日　水曜日　午後７時３９分
MAIN FEATURES
Reduction / Enlargement
See page 4-15
Copies can be enlarged or reduced to the desired
size.
Erase
See page 5-4
Shadows that appear around the edges of copies of
books or thick originals can be erased.
Original
Original
Copy
Copy
Edge erase
Center erase
Enlargement
Reduction
Edge+Center
erase
XY Zoom
See page 4-18
Separate ratio settings can be selected for the
length and width of a copy.
Original
Dual Page Copy
The left and right pages of a book can be
successively copied onto separate sheets.
Copy
Margin Shift
See page 5-3
Margins can be added to copies.
See page 5-5
Book original
Copy
Pamphlet Copy
See page 5-6
One-sided or two-sided pamphlet style copies can
be made.
One-sided copying Image shifted Image shifted
Original
to the right
to the left
Originals (one-sided)
Finished copies are
folded in two.
Left binding
1
2
3
Margin
Two-sided copying
Original
4
Margin
5
6
8
Image shifted Image shifted
to the right
to the left
Originals (two-sided)
2
1
Or
Margin
1-4
First page
7
Margin
4
6
8
Right binding
3
5
7
First page
dragonII_copy_sec.book
5 ページ
２００６年１０月１８日　水曜日　午後７時３９分
MAIN FEATURES
Job Build
See page 5-8
When you have a very large number of originals, the
pages can be scanned in sets.
Transparency Insert
See page 5-23
Inserts can be automatically inserted between
transparencies.
Originals (1-sided)
Copy
1
Originals (2-sided)
300 sheets
150 sheets
Tandem Copy
150 sheets
See page 5-10
Two machines can be used to run a large copy job
in parallel.
Insert sheets
Multi Shot
Multiple original pages can be copied onto a
single sheet of paper in a uniform layout.
Originals
(1-sided)
100 sets of
copies
50 sets of
copies
See page 5-24
Originals
(2-sided)
Copy
50 sets of
copies
*When using the MX-M550U, MX-M620U, or
MX-M700U, the network expansion kit is required.
Covers/inserts
See page 5-12
Front covers, back covers, and inserts can be
added. These can also be copied on.
Book Copy
See page 5-26
Books and other bound originals can be copied
pamphlet style.
Original
Originals
Copy
Left binding
Back cover
First page
First page
Front cover
Insert sheets
Right binding
First page
First page
1-5
dragonII_copy_sec.book
6 ページ
２００６年１０月１８日　水曜日　午後７時３９分
MAIN FEATURES
Tab Copy
See page 5-27
Copying is possible on the tabs of tabbed paper.
Original
Tab paper
Mirror Image
See page 5-31
A mirror image copy can be made.
Copy
Original
Copy
INDEX
INDEX
Tab width
8-1/2" x 11" : Maximum of 5/8" (17mm)
A4 : Maximum of 51/64" (20mm)
Card Shot
See page 5-29
The front and back of a card can be copied onto
one sheet of paper.
This function is convenient for making copies for
certification purposes and helps save paper.
Original
B/W Reverse
See page 5-31
White and black can be inverted on a copy to
produce a negative image.
Original
Copy
Copy
CARD
CARD
Front of
card
CARD
Back of
card
Example:
Portrait
8-1/2" (A4) size
Job programs
Example:
Landscape
8-1/2" (A4) size
See page 5-44
Various steps of a copy operation can be stored
as a program, and up to 10 programs can be
stored. Saving frequently used sets of settings in a
program saves you the trouble of selecting those
settings each time you wish to use them.
Date
See page 5-35
The date can be added to copies.
JOB PROGRAMS
PRESS PROGRAM NUMBER.
RECALL
1-6
2010/APR/4
dragon_01.fm
7 ページ
２００６年１０月１８日　水曜日　午後８時３４分
MAIN FEATURES
Stamp
See page 5-36
Reverse text can be added to copies ("stamp").
Interrupting a copy run
See page 5-46
A copy job in progress can be interrupted for a
rush job.
INTERRUPT
1
AUTO
ORIGINAL
CONFIDENTIAL
81/2x11
AUTO
EXPOSUR
AUTO
Page numbering
See page 5-37
Page numbers can be added to copies.
Offset mode
A4
See page 3-4
Each set of output can be offset slightly from other
sets for easy separation.
Offset mode
Non-Offset mode
*When the Finisher or Saddle stitch finisher is
installed.
Text
See page 5-41
Entered text can be added to copies.
Staple sort mode
See page 3-4
Sets of copies can be automatically stapled.
Original
Copy
Meeting
*When the Finisher or Saddle stitch finisher is
installed.
1-7
dragonII_copy_sec.book
8 ページ
２００６年１０月１８日　水曜日　午後７時３９分
MAIN FEATURES
Saddle stitch
See page 3-5
When a saddle stitch finisher is installed, copies
can be automatically folded in half and stapled at
the fold. (Use with the pamphlet function (see
page 5-6) or book copy function (see page 5-26).)
Document filing function
See chap. 7
A document image can be stored on the hard disk.
A stored file can easily be called up and printed or
transmitted.
Saddle stitch binding
Printed
Document
Image
HDD
Save to
machine's
hard disk
6
7
*When the Saddle stitch finisher is installed.
Hole punching
See page 3-5
Copies can be punched to add holes.
Original
Punch positions
*When the Punch module is installed.
Inserter mode
See page 3-14
Blank or already printed-on sheets of paper can
be added as a cover or an insert without being
printed on. The inserter can be used to feed heavy
sheets of paper that cannot be fed from other
trays.
Original
*When the Inserter is installed.
1-8
Copy
Call up a
saved file to
reuse
Transmitted
dragonII_copy_sec.book
9 ページ
２００６年１０月１８日　水曜日　午後７時３９分
MAIN FEATURES
Energy saving features
This product has the following two power reducing modes that conform to the
Energy Star guidelines to help conserve natural resources and reduce
environmental pollution.
Preheat mode
The preheat mode is the first level of power reduction. The power is reduced
to the fuser unit a preset time after the machine has completed a job and no
further machine operations have been performed. The machine can recover
to the ready condition within a short period of time. The preset time to enter
the mode can be set by a administrator settings.
Products that have earned
the ENERGY STAR® are
designed to protect the
environment through
superior energy efficiency.
Auto power shut-off mode
The auto power shut-off mode is the second level of power reduction. In this mode power is shut off to the
fusing unit and the touch panel. In this state more energy is saved than in the preheat mode but the time to
recover to the ready condition will be longer. The preset time to enter this mode can be set by a administrator
settings.
When this product is used as a printer, and either of the above modes is active, the mode will be deactivated
automatically by an incoming job and the machine will automatically warm up and start to print when it has
reached the ready temperature.
When this product is configured for multi-function operation, and either of the above modes is active, the mode
will be deactivated as above by an incoming print job. Either mode will also be deactivated by operation of
DOCUMENT FILING, IMAGE SEND or COPY mode key.
1-9
1
dragonII_copy_sec.book
10 ページ
２００６年１０月１８日　水曜日　午後７時３９分
PART NAMES AND FUNCTIONS
Exterior
(AR-F15)
1
Saddle stitch finisher (AR-F16)*1 /
9
Finisher (AR-F15)*1 (See page 3-2)
2
Punch module (AR-PN4B)*1 (See page 3-2)
3
Inserter (AR-CF2)*1 (See page 3-14)
4
Automatic document feeder (See page 4-2)
Power switch (See page 1-17)
Turns the power on and off.
If the power does not come on when the power
switch is turned on, check the main power switch to
see if it is turned on.
10
Tray 5 (Large capacity tray (AR-LC6))*1
(See page 2-7)
This automatically feeds and scans multiple sheet
originals. Both sides of two-sided originals can be
scanned at once.
5
11
(See page 2-8)
12
Open to replace toner cartridge.
Operation panel
7
Center tray (See page 4-9)
13
Bypass tray
Special papers (including transparency film) and
copy paper can be fed from the bypass tray.
Tray 3
Tray 3 holds paper. Approximately 500 sheets of
standard (20 lbs. (80 g/m2)) paper can be loaded
in this tray. Tabbed paper and transparencies can
also be loaded.
Finished sheets are deposited here
8
Tray 1-Tray 2
The trays hold paper. Approximately 800 sheets of
standard 8-1/2" x 11" or A4 size paper (20 lbs. (80
g/m2)) can be loaded in tray 1, and approximately
1200 sheets of standard 8-1/2" x 11" or A4 size
paper (20 lbs. (80 g/m2)) can be loaded in tray 2.
Front cover
6
Tray 5 (Large capacity tray (AR-LC7))*1
14
Tray 4
Tray 4 holds paper. Approximately 500 sheets of
standard (20 lbs. (80 g/m2)) paper can be loaded
in this tray.
*1
, 2 , 3 , 10 and 11 are peripheral devices. For information on these devices, see the explanations of the
devices in the manual.
1
1-10
dragonII_copy_sec.book
11 ページ
２００６年１０月１８日　水曜日　午後７時３９分
PART NAMES AND FUNCTIONS
Interior
1
15
Duplex unit
20
Open when a misfeed has occurred in the bypass
tray or large capacity tray.
Open this cover to remove a misfeed from the
fusing unit area.
16
Fusing unit
Right side cover
21
Upper cover of large capacity tray
Open when a misfeed has occurred in the large
capacity tray.
Toner images are fused here.
CAUTION
The fusing unit is hot. Take care in removing misfed
paper.
17
Cover of the duplex unit
22
Push this knob up to open the left side cover.
23
Left cover of paper drawer
Open this cover to remove paper misfed in tray 3 or
tray 4.
Open when a misfeed has occurred in duplex unit.
18
Left side cover release
Toner cartridge*2
This holds toner for printing. The toner cartridge
must be replaced when indicated on the operation
panel.
24
Photoconductive drum
Images are formed on the photoconductive drum.
NOTE
19
Main power switch (See page 1-17)
Do not touch or damage the photoconductive drum.
Keep this switch turned on when the fax option or
Internet fax option is installed.
*2 See page 2-21 for the procedure for installing and replacing the toner cartridge.
1-11
dragon_01.fm
12 ページ
２００６年１０月１９日　木曜日　午後２時５７分
PART NAMES AND FUNCTIONS
■ Other optional equipment
●Network expansion kit (MX-NBX1)
This kit is required to add on the network function.
When this expansion kit is installed, the machine
can be used as a network printer.
●Barcode font kit (AR-PF1)
This kit adds bar code fonts to the machine.
● Data security kit (MX-FRX5)
This kit is used to erase electronic data from the
hard disk and memory immediately after a
document is printed or transmitted.
●PS3 expansion kit (MX-PKX1)
This kit provides compatibility of PostScript level 3
to the printer.
●Facsimile expansion kit (AR-FX8)
This kit is required to add fax function.
●Network scanner expansion kit (MX-NSX1)
This kit is required to add the network scanning
feature.
To add the network scanner function to the
MX-M550U, MX-M620U, or MX-M700U, the
network expansion kit is required.
●Internet fax expansion kit (MX-FWX1)
This kit is required to use the Internet fax function.
To add the Internet fax function, the network
scanner expansion kit is required.
●Application integration module (MX-AMX1)
The application integration module can be
combined with the network scanner function to
append a metadata file to a scanned image file.
●Application communication module (MX-AMX2)
This allows the machine to be linked over a network
to an external software application.
●Additional fax memory (8 MB) (AR-MM9)
●256MB expansion mamory board (AR-SM5)
This extends the memory of the machine.
●External account module (MX-AMX3)
This is required to use an external account
application on the machine.
Peripheral devices are basically optional, but are incorporated in some models as standard equipment.
1-12
dragonII_copy_sec.book
13 ページ
２００６年１０月１８日　水曜日　午後７時３９分
PART NAMES AND FUNCTIONS
Operation panel
DOCUMENT
FILING
IMAGE SEND
1
PRINT
READY
DATA
LINE
DATA
COPY
SYSTEM
JOB STATUS SETTINGS
1
Touch panel
The machine status, messages and touch keys are
displayed on the panel. The document filing, copy,
network scanner*1, and fax*2, Internet fax*3
functions are used by switching to the screen for
the desired function. See the following page.
2
LOGOUT
5
This is used to store, edit, and delete user names
and folder names for the document filing function,
and to configure the administrator settings and
printer configuration settings. (See page 7-24)
6
Mode select keys and indicators
Use to change modes and the corresponding
display on the touch panel.
[DOCUMENT FILING] key
7
PRINT mode indicators
8
9
Press to display the current job status. (See page
1-15.)
[C] key (Clear key)
This key is used in copy mode, document filing
mode, network scanner mode*1, fax mode*2, and
Internet fax mode*3.
10
[START] key
Use this key to start copying in copy mode, scan a
document in network scanner mode*1, or scan a
document for transmission in fax mode*2 or
Internet fax mode*3.
Print data can be received when this indicator is
lit.
DATA indicator
4
[#/P] key
This is used as a program key when using the copy
function, and to dial when using the fax function*2.
READY indicator
Lights up or blinks when print data is being
received. Also lights up or blinks when printing is
being performed.
[JOB STATUS] key
[ ] key ([LOGOUT] key)
This key is used in copy mode, document filing
mode, network scanner mode*1, fax mode*2, and
Internet fax mode*3.
[COPY] key
Press to select the copy mode.
3
Numeric keys
Use to enter numeric values for various settings.
Press to select the document filing mode. (See
page 7-5.)
[IMAGE SEND] key/LINE indicator/DATA
indicator
Press to change the display to network scanner
mode*1, fax mode*2 or Internet fax mode*3. (See
the "Operation manual (for image send)") and
"Operation manual (for facsimile)".)
[SYSTEM SETTINGS] key
11
[CA] key (Clear all key)
This key is used in copy mode, document filing
mode, network scanner mode*1, fax mode*2, and
Internet fax mode*3. Use the key to cancel settings
and perform an operation from the initial machine
state.
*1 When the network scanner option is installed.
*2 When the fax option is installed.
*3 When the Internet fax option is installed.
1-13
dragon_01.fm
14 ページ
２００６年１０月１９日　木曜日　午後１２時５５分
PART NAMES AND FUNCTIONS
Touch panel
The touch panel screens shown in this manual are
printed images, and may appear different from the
actual screens.
■ Selecting a function
[Example 1]
OCK ONTO
0
■ Using the touch panel
[Example 1]
OK
PRINT ON INSERT SHEETS
Items on the touch panel
are easily selectable by
003 / 000
COPY
touching
the
key
003 / 000 associated with the item
001
010 / 000 with a finger. Selection
0666211221
of an item will be
Beep
accompanied with a
tone
beep tone* to confirm
the item was selected.
Also, the key area for the item will be highlighted
for visual confirmation.
JOB QUEUE
OK
CANCEL
YES
NO
PAPER IS FED
FROM INSERTER
SETS / PROG
[Example 2]
A function in the special
functions
screen
is
selected by touching the
key so that it is
highlighted. To cancel
the selection, touch the
highlighted key once
again.
DUAL PAGE
COPY
TANDEM
COPY
* If a grayed out key is touched, a double beep will
sound.
[Example 2]
1/13
COMPLETE
Keys which are grayed
out on any screen are
not selectable.
If a key is highlighted in a
setting screen at the
time the screen appears,
the [OK] key can be
pressed to store the
selection without further
operation.
Copier feature
●
●
●
●
●
Dual page copy
Job build
Tandem copy
Mirror image
B/W Reverse
[Example 3]
The confirmation beeps can be disabled using
"Keys touch sound" in the administrator settings.
(See page 10 of the administrator settings guide.)
A corresponding icon
representing the feature
will appear on the touch
2-SIDED COPY
key and on the main
OUTPUT
1.
2.
screen of the mode
FILE
8 x11 8 x11
3. 8 x14
selected. If this icon is
4.
11x17
QUICK FILE
touched, the setting
screen of the function (or
a menu screen) will
appear, allowing the settings to be checked or
adjusted and the function to be canceled easily.
READY TO SCAN FOR COPY.
SPECIAL MODES
ORIGI
1/2
1/2
1/2
1-14
dragon_01.fm
15 ページ
２００６年１２月１日　金曜日　午前８時５２分
PART NAMES AND FUNCTIONS
■ Job status screen (common to print, scan, fax and Internet fax)
This screen is displayed when the [JOB STATUS] key on the operation panel is pressed.
This screen can be used to display the "JOB QUEUE" (showing stored jobs and the current job) or the
"COMPLETE" job list (showing finished jobs). This screen is used to check jobs, move a job to the top of the JOB
QUEUE, or delete a job.
JOB QUEUE
SETS / PROGRESS
020 / 001
COPYING
COPY
020 / 000
PAPER EMPTY
Suzuki
020 / 000
WAITING
066211221
002 / 000
WAITING
SCAN TO
PRINT JOB
1
STATUS
COPY
The displayed jobs in the job list are themselves
operation keys. To cancel printing or to give a job
the highest print priority, touch the relevant job key
to select the job and execute the desired operation
using the keys described in 8 and 9 .
This shows the current job and the jobs waiting to
be run. The icons to the left of the jobs in the
queue show the job mode. The document filing
reprint job icon is highlighted.
Note that the icon does not become highlighted
during retransmission of a fax/image transmission
job.
Print mode
Copy mode
SCAN mode
Scan to e-mail job
Scan to FTP job
Scan to Desktop job
Scan to Network folder job
Fax mode
Fax send job
Fax reception job
PC-Fax send job
Internet Fax mode
i-Fax send job
1/1
JOB QUEUE
JOB QUEUE
COMPLETE
COMPLETE
DETAIL
DETAIL
PRIORITY
STOP/DELETE
INTERNET-FAX
FAX JOB
Job list
1
"COMPLETE"
job screen
*1
"JOB QUEUE" screen
CALL
INTERNET-FAX
*1 "PAPER EMPTY" in the job status display
When a job status display indicates "PAPER
EMPTY", the specified paper size for the job is not
loaded in any of the trays.
In this case, the job will be suspended until the
required paper is loaded. Other stored jobs will be
printed (if possible) until the required paper is loaded.
(Other jobs will not be printed if the paper runs out
during printing.) If you need to change the paper size
because the specified paper size is not available,
touch the current job key to select it and then touch
the [DETAIL] key described in 10 .
2
Mode select key
This switches the job list display between "JOB
QUEUE" and "COMPLETE".
"JOB QUEUE": Shows stored jobs and the job in
progress.
"COMPLETE": Shows finished jobs.
Files saved using the "FILE" and "QUICK FILE"
functions and finished broadcast transmission
jobs appear as keys in the finished job screen.
The "FILE" or "QUICK FILE" job keys in the
finished job screen can be touched, followed by
the [CALL] key, to call up a finished job and print
or transmit it. A finished broadcast transmission
job key can be touched followed by the [DETAIL]
key to check the result of the transmission.
i-Fax reception job
PC-Internet Fax send job
1-15
dragon_01.fm
16 ページ
２００６年１２月１日　金曜日　午前８時５２分
PART NAMES AND FUNCTIONS
3
[PRINT JOB] key
9
A stored job in the "JOB QUEUE" job list can be
printed ahead of all other stored jobs by selecting
the job and then touching this key.
This displays the print job list of print mode
(copying, printing, fax reception, Internet fax
reception, and self printing).
4
[SCAN TO] key
10
This displays the transmission status and finished
jobs of scan mode (Scan to e-mail, Scan to FTP,
Scan to Desktop, and Scan to Network Folder)
when the network scanner option is installed.
5
[DETAIL] key
This shows detailed information on the selected
job. Files saved using the "FILE" and "QUICK
FILE"
functions
and
finished
broadcast
transmission jobs appear as keys in the finished
job screen. A Quick File in the finished job screen
or the [Filing] key can be touched, followed by the
[CALL] key, to call up a finished job and print or
transmit it. A finished broadcast transmission job
key can be touched followed by the [DETAIL] key to
check the result of the transmission.
[FAX JOB] key
This displays the transmission/reception status
and finished jobs of fax mode (fax and PC-Fax)
when the fax option is installed.
6
[PRIORITY] key
Display switching keys
Use to switch the page of the displayed job list.
7
[INTERNET-FAX] key
This displays the transmission/reception status
and finished jobs of Internet fax mode and PC
Internet fax mode when the Internet fax option is
installed.
8
[STOP/DELETE] key
Use to cancel or delete the current job or delete
the selected reserved job. Note that printing of
received faxes and received Internet faxes cannot
be canceled or deleted.
1-16
11
[CALL] key
When this key is touched after selecting a job in
the COMPLETE job status screen (a job stored
using the FILE or QUICK FILE keys of the
document filing function), the "JOB SETTINGS"
menu screen appears to let you resend or reprint
the finished job. (See "Document filing function"
on page 7-2.)
dragonII_copy_sec.book
17 ページ
２００６年１０月１８日　水曜日　午後７時３９分
TURNING THE POWER ON AND OFF
The machine has two power switches. The main power switch can be found at the upper right after the front cover
is opened. The power switch is located at the upper left of the right side of the machine.
The two switches are normally used as follows:
CAUTION
Before turning off the main power switch, make sure
that the communication and data lights are not
blinking on the operation panel. Turning off the main
power switch or unplugging the power cord while the
lights are blinking may damage the hard disk and
cause the data being stored or received to be lost.
"ON" position
"OFF" position
Main power switch
Power switch
Main power switch: Normally kept in the ON position.
(Be sure to keep ON when using the
fax function.)
Power switch :
Turn to ON position before using
the machine.
Turn OFF at night when the
machine is not used.
Main power switch ON, Power switch ON
The copy, printer, fax*, Internet fax*, network
scanner*, and document filing functions can be
used. If the machine is not used for a certain interval
after turning on the power switch, the machine will
automatically enter a reduced power consumption
state (preheat mode or auto power shut-off mode
(see page 1-9)).
Main power switch ON, Power switch OFF
Set the switches in this way at night or at other times
when the machine is not being used. The touch
panel cannot be used, however, the following
functions will remain operational:
When the fax option is installed:
Automatic fax reception, timer transmission
(automatic transmission at a specified time), and
transmission when a polling request is received from
another machine (remote transmission, relay
broadcast transmission)
When the Internet fax option is installed:
Automatic Internet fax reception
* The required options must be installed to use
these functions.
Main power switch OFF, Power switch ON
Main power switch OFF, Power switch OFF
The copy, printer, fax, Internet fax, network scanner,
and document filing functions cannot be used.
The copy, printer, fax, Internet fax, network scanner,
and document filing functions cannot be used.
Turn both switches off and unplug the power cord if
you suspect a machine failure, if there is a bad
thunderstorm nearby, or when you are moving the
machine.
1-17
1
dragonII_copy_sec.book
18 ページ
２００６年１０月１８日　水曜日　午後７時３９分
AUDITING MODE
Auditing mode can be enabled to keep track of the number of pages printed and transmitted (scanned) by each
account (up to 500 accounts can be established). The page counts can be viewed and totaled as needed.
<This mode is enabled in the administrator settings separately for the copy, printer, fax, Internet fax, network scanner,
and document filing functions (page 7 of the administrator settings guide)>
Using the machine when the auditing mode is enabled
The procedure for making copies when auditing mode has been enabled for the copy function is explained below.
NOTES
● When auditing mode is enabled for document filing and fax/image transmission, a message will appear asking you
to enter your account number each time you switch to the main screen of one of those functions in the touch panel.
Enter your account number in the same way as for copy mode, and then begin the scanning procedure.
● When the account counter is turned on for the printer function, you must enter your account number in the
setting screen of the printer driver on your computer in order to print.
When the account counter is turned on, the right
message appears on the touch panel.
ENTER YOUR ACCOUNT NUMBER.
When the above screen appears, enter your 5-digit account number and then begin the copying procedure.
your account number (5 digits) with
1 Enter
the numeric keys.
LOGOUT
As you enter your
account number, the
hyphens (-) change to
asterisks ( ). If you
enter an incorrect digit,
press the
key and
re-enter the correct digit.
When a correct account number is entered, the
following message will appear.
ACCOUNT STATUS
COPIES
:MADE
/REMAINING
:00,123,000/00,012,456
OK
the appropriate steps to perform
2 Follow
the copy job.
When copying is begun, the following message
will appear.
READY TO SCAN FOR COPY.
PRESS [LOGOUT] WHEN FINISHED.
To perform an interrupt copy job (page 5-46),
touch the [INTERRUPT] key and then enter your
account number as explained in step 1. The
following message will appear.
COPY INTERRUPT MODE.
READY TO SCAN FOR COPY.
If a limit has been set in the administrator settings
for the number of copies that can be made by the
account, the remaining number that can be made
is displayed.
the copy job is finished, press the
3 When
[ ] key ([LOGOUT] key)
Check the number in the display and touch the
[OK] key.
NOTE
If "ACCOUNT NUMBER SECURITY" is enabled in the
administrator settings and an incorrect account
number is entered three times in a row, "PLEASE SEE
YOUR ADMINISTRATOR FOR ASSISTANCE." will
appear (page 8 of the administrator settings guide).
Operation is not possible while this message
appears (about one minute).
1-18
LOGOUT
dragon_02-1.fm
1 ページ
２００６年１０月１８日　水曜日　午後８時２０分
CHAPTER 2
MANAGING THE MACHINE
This chapter explains how to load paper, replace the toner cartridge, and
remove paper misfeeds. It also contains information about supplies.
Page
LOADING PAPER ................................................................................... 2-2
●
Identifying the trays ......................................................................... 2-2
●
Loading paper in paper tray 1 - tray 2 ............................................. 2-2
●
Changing the paper size in paper tray 1 - tray 2 ............................. 2-3
● Loading paper in paper tray 3 ......................................................... 2-5
●
Changing the paper size in paper tray 3 ......................................... 2-5
●
Changing the paper size in paper tray 4 ......................................... 2-6
● Loading paper in paper tray 5 (optional large capacity tray AR-LC6) ... 2-7
●
Loading paper in paper tray 5 (optional large capacity tray AR-LC7) ... 2-8
●
Loading paper in the bypass tray .................................................... 2-10
● Specifications of paper trays (Types and sizes of paper that can be
used in the trays)............................................................................. 2-12
●
Setting the paper type and paper size ............................................ 2-14
● Setting the paper size when a special size is loaded...................... 2-17
SYSTEM SETTINGS .............................................................................. 2-18
● General procedure for system settings ........................................... 2-18
● About the settings ........................................................................... 2-20
REPLACING THE TONER CARTRIDGES ............................................. 2-21
STORAGE OF SUPPLIES ...................................................................... 2-22
MISFEED REMOVAL .............................................................................. 2-23
●
Misfeed removal guidance .............................................................. 2-23
● Misfeed in the transport area, fusing area, and exit area................ 2-24
●
Misfeed in the duplex unit................................................................ 2-25
●
Misfeed in the paper feed area........................................................ 2-26
REMOVING AN ORIGINAL MISFEED ................................................... 2-31
●
Removing a misfed original from the automatic document feeder .. 2-31
TROUBLESHOOTING ............................................................................ 2-32
2-1
dragon_02-1.fm
2 ページ
２００６年１０月２０日　金曜日　午前９時２２分
LOADING PAPER
If the paper runs out during printing, a message will appear in the display.
Follow the procedure below to load paper.
Identifying the trays
The trays are identified using numbers as shown below.
For the types and sizes of paper that can be used in each tray, see page 2-12.
1
Tray 1
This is the left large capacity tray.
2
Tray 3
3
Tray 4
4
Tray 2
This is the right large capacity tray.
5
Tray 5
This is an optional large capacity tray.
6
Bypass tray
NOTES
● Do not use curled or folded paper. Doing so may cause a misfeed.
● Do not place heavy objects or press hard on any tray which is pulled out.
● Do not place objects on the large-capacity tray. This may damage the tray or interfere with operation.
● Load paper with the print side face up. However, when the paper type is set to "PRE-PRINTED" or "LETTER
HEAD", load the paper face down*.
* If the two-sided function is disabled using "DISABLING OF DUPLEX" in the administrator settings (page 11
of the administrator settings guide), load the paper face up.
Loading paper in paper tray 1 - tray 2
8-1/2" x 11" or A4 size paper can be loaded in tray 1 and tray 2. These are parallel large-capacity trays that allow a
total of approximately 2000 sheets of SHARP standard paper (20lbs. (80g/m2)) to be loaded. If you wish to change
the paper size of tray 1 or tray 2, see "Changing the paper size in paper tray 1 - tray 2" on the next page.
1 Pull out paper tray 1-tray 2.
Gently pull the tray out
until it stops.
2 Load paper in the left and right trays.
Indicator line
Indicator line
Lift the paper guide and
load paper in tray 1.*1
Approximately 800 sheets
of SHARP standard paper
(20lbs.(80g/m2)) can be
loaded.
Be sure to return the
paper guide to its
original position after
loading the paper.
Load paper in tray 2.*1
Approximately
1200
sheets
of
SHARP
standard paper (20lbs.
(80g/m2)) can be loaded.
*1 The paper stack must not be higher than the indicator line.
2-2
dragonII_copy_sec.book
3 ページ
２００６年１０月１８日　水曜日　午後７時３９分
LOADING PAPER
3 Gently push tray 1-tray 2 into the machine.
Push the tray firmly all
the
way
into
the
machine.
4 Set the paper type.
If the paper size was changed from an inch size to an
AB size, or from an AB size to an inch size, or if the
paper type was changed, be sure to change the
appropriate settings as explained in "Setting the
paper type and paper size" (See page 2-14).
paper in paper tray 1/tray 2 is now
5 Loading
complete.
Changing the paper size in paper tray 1 - tray 2
To change the paper size of tray 1 - tray 2, follow the steps below.
This section only explains how to change the paper size. For the procedures for opening/closing the tray and loading
paper, see "Loading paper in paper tray 1 - tray 2" (page 2-2).
1 Remove the paper size guide.
Tray 1
the paper size guide to the paper
2 Adjust
size to be used.
Tray 2
(A)
(B)
LT
A4
A4
LT
Hook
Paper guide
With the base of the tray pressed all the way down,
hold down the hook at the bottom on the paper
size guide and pull the paper size guide up slightly.
NOTES
● Do not place heavy objects on the tray or press
down on the tray.
● Before changing the paper size of tray 1, raise the
paper guide.
Paper sizes are inscribed at the slot (A) on the
bottom of the tray and at the hole (B) at the top of
the paper size guide. ("LT" indicates 8-1/2" x 11"
size.)
Align the bottom of the paper size guide with the
slot, and align the hole at the top with the locking
tab.
NOTES
● When attaching the paper size guide, make sure
that the top and bottom of the guide are aligned to
the same paper size.
● If the top and bottom of the paper size guide are not
aligned to the same paper size, skewed feeding
and misfeeds will result.
2-3
2
dragon_02-1.fm
4 ページ
２００６年１０月１８日　水曜日　午後８時４４分
LOADING PAPER
in the paper guide so that it locks
3 Push
into place.
5 Set the paper type and paper size.
For the procedure for configuring these settings,
see "Setting the paper type and paper size" (page
2-14).
An incorrect paper type or paper size setting may
cause automatic selection of the wrong type or
size of paper, and result in a misfeed or otherwise
prevent printing.
Push the paper size guide in until the hook at the
bottom locks into place. (You will hear a "click"
when the hook locks.) Move the paper size guide
slightly to verify that it has locked into place.
steps 1 to 3 to adjust the far paper
4 Repeat
guide to the paper size to be used.
Be sure to adjust the far paper guide to the same
size as the near paper guide.
NOTES
● When removing and attaching the far paper size
guide, take care not to hit the front cover of the
machine.
● Adjust both the front and back guides. If only one
guide is adjusted, skewed feeding and misfeeds
may result.
2-4
dragonII_copy_sec.book
5 ページ
２００６年１０月１８日　水曜日　午後７時３９分
LOADING PAPER
Loading paper in paper tray 3
Approximately 500 sheets of standard paper (20lbs. (80g/m2)) from 11" x 17" to 5-1/2" x 8-1/2"R size (A3 to A5R) can
be loaded in tray 3. Special papers such as tabbed paper and transparency film can also be loaded. For information
on what special papers can be used, see "Specifications of paper trays (Types and sizes of paper that can be used
in the trays)" on page 2-12. To load tabbed paper or transparency film, see "Loading tabbed paper" or "Loading
transparency film" on the next page.
1 Pull out paper tray 3.
3 Gently push tray 3 into the machine.
Gently pull the tray out
until it stops.
2 Load paper into the tray.
The paper stack must not
be higher than the
indicator line (no more
than 500 sheets of
SHARP standard paper
(20lbs. (80g/m2)).
To change the paper
size, see "Changing the paper size in paper tray 3"
below.
Push the tray firmly all
the
way
into
the
machine.
4 Set the paper type.
If the paper size was changed from an inch size to
an AB size, or from an AB size to an inch size, or if
the paper type was changed, be sure to change the
appropriate settings as explained in "Setting the
paper type and paper size" (see page 2-14).
paper
5 Loading
complete.
in paper tray 3 is now
Changing the paper size in paper tray 3
1 Pull out paper tray 3.
4 Gently push tray 3 into the machine.
If paper remains in the tray, remove it.
the guide plates A and B by
2 Adjust
squeezing their lock levers and sliding
them to the paper size to be loaded.
The guide plates A and
B are slidable. Adjust
them to the paper size to
be
loaded
while
squeezing their lock
levers.
3 Load paper into the tray.
Push the tray firmly all the way into the machine.
the paper type of the paper that was
5 Set
loaded in tray 3.
Be sure to change the appropriate settings as
explained in "Setting the paper type and paper size"
(see page 2-14).
If you changed the paper size, be sure to change
the paper size setting. An incorrect paper size
setting will cause the wrong paper to be
automatically selected and may prevent printing or
cause misfeeds.
the paper size in paper tray 3 is
6 Changing
now complete.
2-5
2
dragonII_copy_sec.book
6 ページ
２００６年１０月１８日　水曜日　午後７時３９分
LOADING PAPER
■ Loading tabbed paper
When using tabbed paper, follow the steps below to attach the special guide to the divider plate at the bottom
edge of the tabbed paper. (Tabbed paper cannot be used in tray 4.)
1 Take out the tabbed paper guide.
3 Place the tabbed paper in the tray.
The guide is stored
inside the left side of the
machine as shown.
Be sure to replace the
guide when you have
finished using it.
2 Pull out the tray and attach the guide.
[Example]
Make sure that the positions of the tabs correspond
with the originals as shown below.
Original
Tabbed paper
DEF
ABC
Front side
GHI
JKL
Slide the divider plate to
the position of the
bottom edge of the
tabbed paper and attach
the guide so that it
covers the divider plate.
Place the tabbed paper
with the print side face
up.
1st page
2nd page
3rd page
4th page
1st page
2nd page
3rd page
4th page
push the tray in and set the paper
4 Gently
type to tabbed paper.
(See "Setting the paper type and paper size" on
page 2-14)
■ Loading transparency film
Be sure to load transparency film with the label facing down and the film oriented vertically. Smudging and a
dirty image may result if the film is loaded with the label facing up. (Transparency film cannot be used in tray 4.)
Changing the paper size in paper tray 4
Plain paper from 11" x 17" to 7-1/4" x 10-1/2"R size (A3 to B5) can be loaded in tray 4. For paper that can be used,
see "Specifications of paper trays (Types and sizes of paper that can be used in the trays)" on page 2-12.
The procedures for loading paper in tray 4 and changing the paper size are the same as for tray 3 (see page 2-5).
NOTE
When referring to the explanations of tray 3, keep in mind that special papers such as tabbed paper and
transparency film cannot be used in tray 4. Use tray 3 for special paper.
2-6
dragonII_copy_sec.book
7 ページ
２００６年１０月１８日　水曜日　午後７時３９分
LOADING PAPER
Loading paper in paper tray 5 (optional large capacity tray
AR-LC6)
The large capacity tray can hold up to 3,500 sheets of 8-1/2" x 11" size (A4) SHARP standard paper (20 lbs. (80
g/m2)). If you wish to change the paper size, please consult your dealer (the paper size must be changed by a service
technician).
1 Pull the tray out until it stops.
the tray firmly all the way into the
3 Push
machine.
When the tray is in
operation, do not use
excessive force to pull
the tray out. This may
damage the tray.
The paper table will
automatically rise to the
paper feed position.
the paper in the center of the paper
2 Place
table.
The paper stack must
not be higher than the
indicator line (up to
3,500 sheets of SHARP
standard paper (20 lbs.
(80 g/m2))
If the paper type was
changed, be sure to change the appropriate
settings as explained in "Setting the paper type
and paper size" (See page 2-14).
■ Specifications
Name
Large capacity tray (AR-LC6)
Paper size
8-1/2" x 11" (A4)
Paper weight
16 to 28 lbs. (60 to 105 g/m2)
Paper capacity (plain)
3500 sheets (20 lbs. (80 /m2))
Dimensions
14-23/32" (W) x 21-1/2" (D) x 20-13/32" (H)
(376 mm (W) x 546 mm (D) x 518 mm (H))
Power supply
Supplied from the main unit
Weight
Approximately 62.9 lbs. (28.5 kg)
Overall dimensions when
attached to machine
53-3/64" (W) x 26-47/64" (D)
(1347 mm (W) x 679 mm (D))
Specifications are subject to change for improvement without notice.
2-7
2
dragonII_copy_sec.book
8 ページ
２００６年１０月１８日　水曜日　午後７時３９分
LOADING PAPER
Loading paper in paper tray 5 (optional large capacity tray
AR-LC7)
An optional large capacity tray (AR-LC7) is available for the machine. The AR-LC7 can hold up to 3000 sheets of 20
lbs. (80 g/m2) paper. (See the following "Specifications" for the types of paper that can be used in the large capacity
tray.)
When installed, the AR-LC7 operates as "Tray 5". The AR-LC7 cannot be used together with the AR-LC6 described
on page 2-7.
■ Part names
Operation button /
Indicator
To load paper in the tray,
press this button, wait until
the indicator turns off, and
then pull the tray out.
Top cover
Open this cover to
remove a misfeed.
● Load paper in the tray with the print side face up.
However, if the paper type is "PRE-PRINTED" or
"LETTER HEAD", load the paper with the print side
face down*.
* If the two-sided function is disabled using
"DISABLING OF DUPLEX" in the administrator
settings (page 11 of the administrator settings
guide), load the paper face up.
■ Specifications
Name
Large capacity tray (AR-LC7)
Paper sizes*
11" x 17" (A3), 8-1/2" x 14" (B4),
8-1/2" x 11" (A4), 8-1/2" x 11"R (A4R)
Paper weight 16 to 28 lbs. (60 to 105
g/m2)
Number
of
paper
trays
/Paper capacity
One tray 3000 sheets (20 lbs. or 80
g/m2)
Power supply
Supplied from the machine
Dimensions
27-5/32" (W) x 23-7/64" (D) x
20-17/32" (H) (690mm (W) x 587mm
(D) x 521.5mm (H))
Weight
Approx. 110 lbs. (Approx. 50 kg)
Paper size display
NOTES
● If you wish to change the paper size, please consult
your dealer (the paper size must be changed by a
service technician).
● Do not use curled or folded paper. This may cause
misfeeds.
● When the tray has been pulled out, do not place
heavy objects on the tray or press down on the tray.
● Do not place any objects on the large capacity tray
or use it instead of a chair or step. This may
damage the tray and interfere with the use of the
bypass tray.
* The indicated sizes of plain paper can be used.
When using the AR-LC7, refer also to "More
information on plain paper" on page 2-13.
Specifications are subject to change for improvement
without notice.
2-8
dragonII_copy_sec.book
9 ページ
２００６年１０月１８日　水曜日　午後７時３９分
LOADING PAPER
■ Loading paper in the AR-LC7
If the paper runs out during printing, a message will appear in the display. Follow the procedure below to load
paper.
1 Pull the tray out until it stops.
Pull the finger grip up
and pull the tray out
until it stops.
CAUTION
When loading paper, take care not to insert your
hands into holes on paper table.
Do not insert your
hands here.
2
NOTE
To add or change paper, press the operation button.
When the button is
pressed, the indicator
will blink until the paper
table stops descending.
Do not pull the tray out
until the indicator turns
off. Attempting to pull
the tray out when the indicator is blinking or solidly lit
may damage the tray.
2 Place the paper on the paper table.
The paper stack must
not be higher than the
indicator line.
When the paper tray is
pulled out, the paper
Indicator
table
will
have
line
descended
to
a
position
where
approximately 500 sheets of 8-1/2" x 11" size (A4)
20lbs. (80g/m2) paper can be placed. After the
paper is placed, the paper table will descend to a
position where an additional approximately 500
sheets can be placed. When the paper table has
descended all the way, approximately 3000 sheets
can be held.
If a different type of paper is loaded that was used
previously, the paper settings for tray 5 must be
changed on the machine. Be sure to change to the
appropriate settings as explained in "Setting the
paper type and paper size" on page 2-14.
NOTES
Do not insert objects in
the tray or attempt to
place spare paper in
the tray. This may
damage the tray.
● Use SHARP-recommended paper (page 2-22).
Special paper cannot be used.
the tray firmly all the way into the
3 Push
machine.
After the tray is pushed
in, the indicator will
blink until the paper
table
finishes
ascending and then
light solidly.
2-9
dragonII_copy_sec.book
10 ページ
２００６年１０月１８日　水曜日　午後７時３９分
LOADING PAPER
Loading paper in the bypass tray
The bypass tray can be used to print on plain paper, postcards, label sheets, tabbed paper, and other special papers.
When using SHARP standard paper, up to 100 sheets can be loaded (up to 20 postcards) for continuous printing
similar to the other trays. For the paper types that can be used in the bypass tray, see "Specifications of paper trays
(Types and sizes of paper that can be used in the trays)" on page 2-12.
NOTE
After loading the paper in the bypass tray, be sure to set the paper type and size (step 4) if these were changed.
1 Open the bypass tray.
the type and size of the paper loaded in
4 Set
the bypass tray.
If the paper size was changed from an inch size to an
AB size, or from an AB size to an inch size, or if the
paper type was changed, be sure to change the
appropriate settings as explained in "Setting the
paper type and paper size" (see page 2-14).
When loading 11" x 17",
8-1/2" x 14", 8-1/2" x 13",
or 8-1/2" x 11"R, A3, B4,
A4R size paper, be sure
to pull the auxiliary tray
all the way out. If the
auxiliary tray is not
pulled all the way out, the size of the loaded paper
will not be correctly displayed.
■ Loading tabbed paper in the bypass
tray
[Example]
Make sure that the positions of the tabs correspond
with the originals as shown below.
Original
Tabbed paper
DEF
ABC
the bypass tray guides to the width of
2 Set
the copy paper.
completes the procedure for loading
5 This
paper in the bypass tray.
GHI
Front side
JKL
1st page
2nd page
3rd page
4th page
Place the tabbed paper face up.
the copy paper all the way into the
3 Insert
bypass tray. (Do not force the paper in.)
Place the copy paper
face up. If the bypass
tray guides are set wider
than the copy paper, the
inside of the machine
may become soiled,
resulting in smudges on
succeeding copies. A gap may cause skewing
or wrinkling.
2-10
Front
1st page
2nd page
3rd page
4th page
dragonII_copy_sec.book
11 ページ
２００６年１０月１８日　水曜日　午後７時３９分
LOADING PAPER
■ Important points when using the
bypass tray
● Be sure to load 5-1/2" x 8-1/2" paper, A5 paper,
and postcards as shown (1) horizontal loading in
the diagram below.
(1)
(2)
2
(1):Horizontal loading
(2):Vertical loading
● When loading plain paper other than SHARP
standard paper, special media other than
postcards, SHARP-recommended transparency
film, or paper to be printed on the back, the
paper must be loaded one sheet at a time.
Loading more than one sheet at a time will cause
misfeeds.
● Before loading heavy paper, straighten any
curling in the paper.
● When adding paper, remove any paper
remaining in the tray, combine it with the paper to
be added, and reload as a single stack.
● Do not use paper that has already been printed
on by a plain paper fax machine or a laser
printer. This may cause printed images to
become dirty.
● When printing on transparency film, be sure to
remove each sheet as it exits the machine.
Allowing sheets to stack in the output tray may
cause curling.
● Use only Sharp-recommended transparency
film. Transparency film should be loaded in the
bypass tray with the label facing down and the
film oriented vertically. Smudging and a dirty
image may result if the film is placed with the
label facing up.
Label facing down
● When loading multiple sheets of transparency
film in the bypass tray, be sure to fan the sheets
several times before loading.
● Use only tabbed sheets that are made of paper.
Tabbed sheets made of film or other material
cannot be used.
2-11
dragon_02-1.fm
12 ページ
２００６年１１月２９日　水曜日　午後８時４４分
LOADING PAPER
Specifications of paper trays (Types and sizes of paper that
can be used in the trays)
The specifications for the types and sizes of paper that can be loaded in the paper trays are shown below.
Tray No.
(tray name)
Tray 1
Tray 2
Applicable paper types
Applicable paper sizes
Plain paper (Refer to the next page 8-1/2" x 11", A4
"More information on plain paper".) 8-1/2" x 11", A4
Paper weight
16 to 28 lbs.
(60 to 105g/m2)
• When "AUTO-INCH" is selected in "Setting
the paper type and paper size" (page
2-14), the following paper sizes can be
automatically detected:
11" x 17", 8-1/2" x 14", 8-1/2" x 11", 8-1/2"
Plain paper
16 to 34 lbs.
x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R
(Refer to the next page "More
(60 to 128g/m2)
information on plain paper".)
• When "AUTO-AB" is selected in "Setting the paper
type and paper size" (page 2-14), the following
paper sizes can be automatically detected:
A3, B4, A4, A4R, B5, B5R, A5R, 8-1/2" x 13"
• Non-standard sizes
Tray 3
Special paper
(Refer to the
next
page
"More
information on
special media
that can be
used".)
Tray 4
Bypass tray
• Heavy paper
• Transparency
film
• Labels
• Tabbed paper
• When "AUTO-INCH" is selected in "Setting
the paper type and paper size" (page
2-14), the following paper sizes can be
automatically detected:
8-1/2" x 11", 8-1/2" x 11"R (only 8-1/2" x
11" for tabbed paper)
• When "AUTO-AB" is selected in "Setting the paper
type and paper size" (page 2-14), the following
paper sizes can be automatically detected:
A4, A4R, B5, B5R (only A4 for tabbed paper)
• Non-standard sizes smaller than 8-1/2" x 11" or A4
• 40 sheets of transparency film can be loaded
• Tabbed paper can be used
See the remarks
for special papers
on the following
page.
• When "AUTO-INCH" is selected in "Setting
the paper type and paper size" (page
2-14), the following paper sizes can be
automatically detected:
11" x 17", 8-1/2" x 14", 8-1/2" x 11", 8-1/2"
Plain paper (Refer to the next
x 11"R, 7-1/4" x 10-1/2"R
16 to 34 lbs.
page "More information on plain
• When "AUTO-AB" is selected in "Setting (60 to 128g/m2)
paper".)
the paper type and paper size" (page
2-14), the following paper sizes can be
automatically detected:
A3, B4, A4, A4R, B5, B5R, 8-1/2" x 13"
• Non-standard sizes
Same as tray 3. Postcards can also be used.
However,
• Up to 100 sheets of plain paper can be loaded.
• Up to 20 sheets of transparency film can be loaded.
• Up to 20 postcards can be loaded.
The same paper
as tray 3, and also
14 lbs. to 15 lbs.
(52 to 59 g/m2) thin
paper can be used.
Tray 5
(AR-LC6)
Same as tray 2.
Tray 5
(AR-LC7)
Plain paper (Refer to the next page 11" x 17", 8-1/2" x 14", 8-1/2" x 11", 8-1/2" x 11"R, 16 to 28 lbs.
"More information on plain paper".) A3, B4, A4, A4R
(60 to 105g/m2)
2-12
dragonII_copy_sec.book
13 ページ
２００６年１０月１８日　水曜日　午後７時３９分
LOADING PAPER
■ More information on plain paper
Incorrect feeding may result in poor toner fusing (the toner does not adhere to the paper well and can be rubbed
off), skewed feeding, misfeeds, or other failures.
Plain
paper
Paper in inch system
Paper in AB system
5-1/2" x 8-1/2" to 11" x 17"
A5 to A3
SHARP standard paper
(See page 2-22)
17 lbs. (64g/m2)
Restrictions on paper
other
than
SHARP
standard paper
16 to 28 lbs. or 60 to 105g/m2
Recycled, colored, pre-punched, pre-printed and letterhead papers must conform to the same conditions as
above.
■ More information on special media that can be used
Incorrect feeding may result in poor toner fusing (the toner does not adhere to the paper well and can be rubbed
off), skewed feeding, misfeeds, or other failures.
Type
Remarks
Heavy paper
• For 5-1/2" x 8-1/2" to 8-1/2" x 11" or A5 to A4 sizes, heavy paper ranging
from 16 to 34 lbs. or 106 to 128 g/m2 can be used.
• Other heavy papers
65 lbs. (176 g/m2) can be used.
110 lbs. (200 to 205 g/m2) can be used but only for 8-1/2" x 11", A4 paper
in the portrait orientation.
• For 5-1/2" x 8-1/2" or A5 paper, the orientation must be landscape.
Transparency film,
Tabbed paper
• Use SHARP recommended paper.
• Use only tabbed sheets that are made of paper. (Tabbed sheets made of
film or other material cannot be used.)
Postcards
• Japanese official postcards can be used.
Special
paper
■ Paper that can be used for automatic two-sided printing
Paper used for automatic two-sided printing (paper that can be fed through the duplex module) must meet the
following conditions:
Paper type
Paper size
:Plain paper as specified on page above.
:Must be one of the following standard sizes: 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2"
x 11"R, 7-1/4" x 10-1/2" or 5-1/2" x 8-1/2"R (A3, B4, A4, A4R, B5, B5R or A5R)
Paper weight :16 to 34 lbs. (64 to 128 g/m2)(special heavy papers indicated in the table above)
NOTES
● Special papers (explained above) cannot be used for automatic two-sided printing. However, certain special
heavy papers (index paper, cover paper) can be used.
● Various types of plain paper and special paper are sold. Some of these cannot be used in the machine. Please
consult your retailer or your dealer when buying paper.
● The image quality and toner fusibility of special papers may change due to ambient conditions, operating
conditions, and paper characteristics, resulting in image quality inferior to that of SHARP standard paper.
2-13
2
dragonII_copy_sec.book
14 ページ
２００６年１０月１８日　水曜日　午後７時３９分
LOADING PAPER
Setting the paper type and paper size
Follow these steps to change the paper type setting when the paper type has been changed in a paper tray. For the
paper types that can be used in each tray, see page 2-12.
1 Press the [SYSTEM SETTINGS] key.
The system setting
menu
screen
will
appear.
PY
SYSTEM
JOB STATUS SETTINGS
5 Touch the [TYPE / SIZE] key.
PER TRAY SETTINGS
TYPE / SIZE
TRAY 3
PRINT
2
Touch the [PAPER TRAY SETTINGS] key.
The paper tray selection
screen will appear.
PAPER TRAY
SETTINGS
RINT
PLAIN / 81/2x11
FAX
COPY
DOC.
FILING
I-FAX
the type of paper that was loaded in
6 Select
the tray.
Example: The paper type of tray 3 is selected
SYSTEM SETTINGS
CANCEL
TRAY 3 TYPE/SIZE SETTING
SELECT THE PAPER TYPE.
1/2
ATA
ORWARD
PRINTER
CONDITION
PLAIN
LETTER HEAD
PRE-PRINTED
PRE-PUNCHED
LABELS
RECYCLED
COLOR
TRANSPARENCY
HEAVY PAPER
TAB PAPER
1/2
Touch the desired paper type to select it. The
paper size setting screen will appear.
3 Touch the [TRAY SETTINGS] key.
PAPER TRAY SETTINGS
NOTES
● Tabbed paper can only be used in tray 3, bypass
tray and the inserter.
● Heavy paper, label sheets, and transparency film
cannot be loaded in trays 1, 2, 4, and 5.
TRAY SETTINGS
the setting screen of the desired
4 Display
paper tray.
SYSTEM SETTINGS
OK
PAPER TRAY SETTINGS
TYPE / SIZE
TRAY 1
FIXED PAPER SIDE 1/8
PLAIN / 81/2x11
DISABLE DUPLEX
PRINT
COPY
FAX
I-FAX
DOC.
FILING
DISABLE STAPLE
DISABLE PUNCH
Touch the
key or
key to display the
setting screen of the desired paper tray.
NOTE
To automatically switch to a tray with the same size
and type of paper (if there is one) in the event that the
paper tray runs out of paper, display the last screen
with the
key and select [AUTO TRAY
SWITCHING].
2-14
dragonII_copy_sec.book
15 ページ
２００６年１０月１８日　水曜日　午後７時３９分
LOADING PAPER
the size of paper that was loaded in
7 Select
the tray.
Touch the appropriate keys (checkboxes).
SYSTEM SETTINGS
TYPE
TRAY3 TYPE/SIZE SETTING
OK
SIZE
TYPE
AUTO-INCH
PLAIN
AUTO-AB
11X17,81/2 X14,81/2 X11
81/2 X11R,71/4X101/2,51/2X81/2R
A3,A4,A4R,A5R,B4,B5
B5R,216X330(81/2X13)
■ User type
Select a "User type" when the name of the paper
type does not appear in the selections or when you
wish to select the tray attributes yourself.
Touch the
key in step 5 on the previous page
to display the user type selection screen and then
select a user type.
SYSTEM SETTINGS
SIZE INPUT
X17
Y11
NON STANDARD
SIZE
CANCEL
TRAY 3 TYPE/SIZE SETTING
2/2
SELECT THE PAPER TYPE
[AUTO-INCH] key
[AUTO-AB] key
[NON STANDARD SIZE] checkbox :
Select when you have
loaded a non-standard size
of paper (see page 2-17).
NOTE
Sizes that can be selected vary depending on the
selected paper type.
USER TYPE 1
USER TYPE 2
USER TYPE 3
USER TYPE 5
USER TYPE 6
USER TYPE 7
USER TYPE 4
2
1/2
: Select when you have
loaded an AB size of paper.
[SIZE INPUT] key : Select to directly enter a
paper size (see page 2-17).
the
8 Touch
screen.
2/2
: Select when you have
loaded an inch-based size
of paper.
paper settings for each tray and
10 Configure
then touch the [OK] key to exit.
NOTE
The size and type of paper loaded in the bypass tray
can also be set from the paper setting screen. Touch
the [PAPER SELECT] key in the main screen to
display the paper selection screen, and then touch
the [PAPER SELECT] key of the bypass tray and go
to step 5.
[OK] key in the size setting
You will return to the tray setting screen of step 4.
output functions that can be used
9 Select
with the selected tray.
PRINT
COPY
FAX
I-FAX
DOC.
FILING
Touch the checkboxes
under the desired items
to select them.
NOTE
When the inserter (option) is selected, printing of
faxes and Internet faxes is not possible.
2-15
dragonII_copy_sec.book
16 ページ
２００６年１０月１８日　水曜日　午後７時３９分
LOADING PAPER
■ Programming and editing paper types
To program or edit the name of a paper type or set paper attributes, follow the steps below.
the [PAPER TYPE REGISTRATION]
1 Touch
key.
OK
4 Set the paper attributes.
Touch the checkboxes to the left of the items to
select them.
CANCEL
PAPER TYPE REGISTRATION
PAPER TYPE REGISTRATION
TYPE NAME
the paper type that you wish to
2 Select
program or edit.
SYSTEM SETTINGS
OK
PAPER TYPE REGISTRATION
SELECT THE PAPER TYPE TO EDIT.
TYPE 2
USER TYPE
1 TYPEUSER
USER
PAPER
REGISTRATION
USER TYPE 5
USER TYPE 6
USER
3 Touch the [TYPE NAME] key.
A character entry screen appears. Enter up to 14
characters. Refer to page 7-29 for the procedure
for entering characters.
CANCEL
PAPER TYPE REGISTRATION
No.01
TYPE NAME
EXIT
No.01
USER TYPE 1
FIXED PAPER SIDE
DISABLE DUPLEX
DISABLE STAPLE
DISABLE PUNCH
EXIT
USER TYPE 1
FIXED PAPER SIDE
DISABLE DUPLEX
DISABLE STAPLE
DISABLE PUNCH
FIXED PAPER SIDE:
Select this checkbox when paper is to be loaded
print side down in the tray. Make sure a checkmark
does not appear when paper is to be loaded print
side up.
• If the two-sided function is disabled using
"DISABLING OF DUPLEX" in the administrator
settings (page 11 of the administrator settings
guide), load the paper face up.
DISABLE DUPLEX:
Prohibits two-sided printing. Enable when the
backside of the paper cannot be printed on.
DISABLE STAPLE:
Prohibits stapling. Enable when using special
papers such as transparency film and label
sheets.
DISABLE PUNCH:
Prohibits punching. Enable when using special
papers such as transparency film and label
sheets.
NOTES
● Tray attributes depend on the selected paper.
● "FIXED PAPER SIDE" and "DISABLE DUPLEX"
cannot be simultaneously enabled.
the [EXIT] key to
5 Touch
programming/editing procedure.
2-16
exit
the
dragonII_copy_sec.book
17 ページ
２００６年１０月１８日　水曜日　午後７時３９分
LOADING PAPER
Setting the paper size when a special size is loaded
NOTE
Special sizes of paper cannot be loaded in trays 1, 2, 4 and 5.
Trays 3 and the bypass tray
Inserter (option)
steps 1 through 5 of "Setting the
1 Perform
paper type and paper size" (see page 2-14).
steps 1 through 5 of "Setting the
1 Perform
paper type and paper size" (see page 2-14).
the [SIZE INPUT]
2 Touch
touch the [INCH] tab.
2 Touch the [SIZE SELECT] key.
OK
Y
X
17
(5 1/2 17)
Y
11
(5 1/2 11 5/8)
key and then
The size entry palette
appears.
11X17,81/2X14,81/2X
81/2X11R,71/4X101/2,5
A3,A4,A4R,A5R,B
B5R
AUTO-INCH
inch
AUTO-AB
The
size
selection
screen appears.
inch
SIZE SELECT
INCH
AB
the
key or the
key to enter
3 Touch
the X (width) and Y (length) dimensions of
3 Select the desired paper size.
SYSTEM SETTINGS
TYPE
X
OK
Y
X
17
(5 1/2 17)
Y
11
(5 1/2 11 5/8)
inch
inch
X (width) is initially
selected. To enter Y
(length), touch the [Y]
key and then enter the
length.
4 Touch the [OK] key.
X
OK
Y
X
17
(5 1/2 17)
Y
11
(5 1/2 11 5/8)
SIZE
PLAIN
A4R
A5R
B4
B5
B5R
216x330(81/2x13)
4 Touch the [OK] key.
You will return to the size
setting screen of step 2.
inch
TYPE
SIZE
inch
INCH
AB
2/2
A4
A3
OK
There are separate screens for inch-based paper
selection and AB paper selection. Touch the
key or the
key to switch between the screens.
INCH
AB
TYPE
INSERTER TYPE/SIZE SETTING
the paper.
paper is a non-standard size, select
5 Ifthethe[NON
STANDARD SIZE] checkbox.
You will return to the size
setting screen of step 2.
OK
2/2
A4
A4R
B4
B5
steps 8 through 10 of "Setting the
5 Perform
paper type and paper size" (pages 2-15).
11X17,81/2X14,81/2X11
81/2X11R,71/4X101/2,51/2X81/2R
A3,A4,A4R,A5R,B4,B5
B5R,216x330(81/2x13)
X17
Y115/8
NON STANDARD
SIZE
steps 8 through 10 of "Setting the
6 Perform
paper type and paper size" (pages 2-15).
2-17
2
dragon_02-2.fm
18 ページ
２００６年１１月３０日　木曜日　午後２時１３分
SYSTEM SETTINGS
The system settings can be used as needed to meet the needs of your workplace. The items that can be set with the
system settings are shown below.
● Total count . . . . . . . . . . . . . . . . . . The number of pages processed by the machine and optional equipment
can be displayed. (See page 2-20)
● Default settings . . . . . . . . . . . . . . Used to configure the screen contrast, date and time, and keyboard
selection*1 settings. (See page 2-20)
● List print . . . . . . . . . . . . . . . . . . . . Used to print lists of settings and fonts. (See page 2-20)
● Paper tray settings . . . . . . . . . . . . The paper type, paper size and automatic tray switching can be set for each
tray. Automatic tray switching allows feeding to switch between trays loaded
with the same type and size of paper. If one tray runs out of paper during
printing, printing will continue from the other tray. (See page 2-20)
For the detailed descriptions and use of the settings listed below, see the fax, image send, and printer
manuals.
● Address control*1 . . . . . . . . . . . . . Used to store information for various functions.
● Sender control*2 . . . . . . . . . . . . . . Used to store the sender's information that appears on your Scan to E-mail
transmissions at the destination.
● Fax data receive/forward*1 . . . . . . Faxes received to memory and received Internet faxes can be forwarded to
another destination.
● Printer condition . . . . . . . . . . . . . . Used to configure default settings for the printer function (see the Operation
manual (for printer)).
● Document filing control*2. . . . . . . . . Used to configure default settings for the document filing function. (pages 7-25
to 7-28)
● Administrator settings . . . . . . . . . These are items that are used by the administrator of the machine to
configure machine settings. A key appears for these settings in the system
settings menu screen. For information on these settings, see the
administrator settings guide.
*1 These settings can be configured in a system where the facsimile, network scanner and Internet fax function is
available.
*2 These settings can be configured in a system where the network scanner function is available.
General procedure for system settings
1 Press the [SYSTEM SETTINGS] key.
The system setting
menu
screen
will
appear.
PY
SYSTEM
JOB STATUS SETTINGS
3 Touch the [CLOCK] key.
Touch the [CLOCK] key and then the following
screen appears.
SYSTEM SETTINGS
CLOCK ADJUST
2
Touch the key of the desired item to
display its setting screen.
The example of selecting the [DEFAULT SETTINGS]
key and then the [CLOCK] key is explained below.
SYSTEM SETTINGS
EXIT
TOTAL COUNT
DEFAULT
SETTINGS
LIST PRINT
PAPER TRAY
SETTINGS
ADDRESS CONTROL
SENDER CONTROL
FAX DATA
RECEIVE/FORWARD
PRINTER
CONDITION
DOCUMENT FILING
CONTROL
ADMINISTRATOR SETTINGS
The system settings are described in detail on the
following pages.
2-18
OK
YEAR
MONTH
DAY
HOUR
MINUTE
2010
04
04
11
30
DAYLIGHT SAVING TIME SETTING
DATE FORMAT
the year, month, day, hour or minute
4 Touch
key, and then use the
or
key to
adjust the setting.
●If you select a non-existent date (for example,
Feb. 30), the [OK] key will gray out to prevent
entry of the date.
●Select [DAYLIGHT SAVING TIME SETTING]
checkbox to have the time automatically
change at the beginning and end of daylight
saving time.
dragonII_copy_sec.book
19 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SYSTEM SETTINGS
5 Touch the [DATE FORMAT] key.
The following screen appears.
SYSTEM SETTINGS
OK
DATE FORMAT
2010/04/04/SUN 11:30
MM/DD/YYYY
DAY-NAME
POSITION
FIRST
12-HOUR
DD/MM/YYYY
LAST
24-HOUR
YYYY/MM/DD
More information on setting procedures
In the following type of screen, a setting is selected
by touching the key so that a checkmark ( )
appears. The settings below are configured to
allow use of tray 1 in print, copy, and fax modes. To
display the next screen, touch the
or
keys.
SYSTEM SETTINGS
OK
PAPER TRAY SETTINGS
TYPE / SIZE
TRAY1
FIXED PAPER SIDE
1/8
PLAIN / 81/2X11
DISABLE DUPLEX
wish to change the format of the date
6 Ifandyoutime,
touch the desired format keys.
PRINT
COPY
FAX
I-FAX
DOC.
FILING
2
DISABLE STAPLE
DISABLE PUNCH
Touched keys are highlighted.
The selected format is applied to lists printed out in
"LIST PRINT".
7 Touch the [OK] key.
You will return to the
date and time setting
screen.
OK
AME
ON
T
12-HOUR
8 Touch the [OK] key.
9 To exit the settings, touch the [EXIT] key.
SYSTEM SETTINGS
EXIT
TOTAL COUNT
DEFAULT
SETTINGS
LIST PRINT
PAPER TRAY
SETTINGS
ADDRESS CONTROL
SENDER CONTROL
FAX DATA
RECEIVE/FORWARD
PRINTER
CONDITION
DOCUMENT FILING
CONTROL
ADMINISTRATOR SETTINGS
2-19
dragonII_copy_sec.book
20 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SYSTEM SETTINGS
About the settings
■ Total count
■ List print
This displays the following sheet counts (the
counts that can be displayed vary depending on
the options installed):
This is used to print lists of machine settings and a
test page to check resident fonts.
The following lists and pages are available:
Number of pages output by the machine.
Number of original pages transmitted by the
machine.
3 Number of times the automatic document feeder
was used to feed original pages and number of
times the stapler was used (if installed).
4 Number of pages stored by document filing.
In the case of 1 only,
●11" x 17" (A3) size paper is counted as two
sheets.
●Each sheet of paper used for automatic twosided copying is counted as two sheets (11" x
17" (A3) paper is counted as four sheets).
●Paper with an entered size of 15-1/8" (384 mm)
or larger is counted as two sheets (four sheets
during automatic two-sided copying).
●All custom setting list
Shows the hardware status, software status,
printer configuration settings, tray settings, and
counts.
●Printer test page
Shows the PCL symbol set list, fonts, network
interface (NIC interface) settings, and settings
used for the NIC card.
●Sending address list
One touch destination list, group list, program
list, and memory box list.
●Document filing user / folder list
Shows the user names and folder names for
document filing.
●Sender control list
Shows the senders that have been stored.
1
2
■ Default settings
NOTE
The following settings can be configured:
●Display contrast
Screen contrast adjustment is used to make the
LCD touch panel easier to view under various
lighting conditions. Touch the [LIGHTER] key to
make the screen lighter, or the [DARKER] key to
make the screen darker.
●Clock
Use this to set the date and time in the
machine's built-in clock. This clock is used by
functions that require date and time information.
●Keyboard select
The layout of the keyboard that appears in letter
entry screens can be changed.
Select the arrangement of the letter keys that
you find easiest to use.
The
following
three
alphabet
configurations are available:
keyboard
● Keyboard 1 (QWERT... configuration)*
● Keyboard 2 (AZERTY...configuration)
● Keyboard 3 (ABCDEF...configuration)
* The default setting is "Keyboard 1".
(Example: Character entry
Keyboard 3 is selected)
screen
ABC
2-20
when
abc
A test page cannot be printed if "PROHIBIT TEST
PAGE PRINTING" (See the "Operation manual (for
printer)".) has been set to "prohibited" in the
administrator settings.
■ Paper tray settings
The paper type, paper size, enabled modes and
automatic tray switching can be set for each tray.
See page 2-14 for details on setting the paper type
and paper size. Automatic switching to another
paper tray is used to automatically switch to
another tray with the same size and type of paper in
the event that the paper runs out during continuous
printing. This requires that the trays be loaded with
the same size of paper. The paper tray settings can
be enabled or disabled for each tray, and for printer
mode, copy mode, fax mode, Internet fax mode,
and document filing mode. To enable any function,
touch the check box key so that a checkmark ( )
appears.
dragon_02-2.fm
21 ページ
２００６年１０月２３日　月曜日　午後１２時５５分
REPLACING THE TONER CARTRIDGES
When toner runs low, a message will appear to inform you that the toner cartridge must be replaced.
NOTE
To view the approximate amount of toner remaining, hold down the [COPY] key during printing or when the
machine is on standby. The percentage of toner remaining will appear in the display while you hold down the key.
When the percentage falls to "20-0%" , obtain a new toner cartridge and keep it ready for replacement.
Follow the steps below to replace the toner cartridge.
1 Open the front cover.
Shake
the
toner
cartridge horizontally.
Do not rotate it as shown
at left.
4 Insert the new toner cartridge.
Align the toner cartridge
with the insert hole and
push it in as shown.
Do not rotate the
cartridge.
2 Remove the toner cartridge gently.
the cartridge in until it locks securely
5 Push
in place.
Hold the toner cartridge
with both hands as
shown in the illustration,
and pull it out of the
machine.
the new toner cartridge from the
3 Remove
box and shake it thoroughly for 10
6 Close the front cover.
seconds.
CAUTION
It is important to
thoroughly shake the
supply cartridge for 10
seconds as shown in
the diagram in order to
ensure
proper
operation of toner
supply system.
CAUTION
● Do not throw the toner cartridge into a fire. Toner may fly and cause burns.
● Store toner cartridges out of the reach of small children.
NOTE
Place the used toner cartridge in the plastic bag and store it. When placing the toner cartridge in the bag, insert
it horizontally, not vertically. If the cartridge is stood on end, the collected used toner may spill out and soil the floor
or your clothes.
2-21
2
dragonII_copy_sec.book
22 ページ
２００６年１０月１８日　水曜日　午後７時３９分
STORAGE OF SUPPLIES
Standard supplies for this product that can replaced by the user include paper, toner cartridges, and staple cartridges
for the finisher.
For best copying results, be sure to use only Sharp Genuine Supplies which are designed,
engineered, and tested to maximize the life and performance of Sharp products. Look for
the Genuine Supplies label on the toner package.
GENUINE SUPPLIES
■ Proper storage
1.
●
●
●
Store the supplies in a location that is:
clean and dry,
at a stable temperature,
not exposed to direct sunlight.
2. Store paper in the wrapper and lying flat.
3. Paper stored in packages standing up or out of
the wrapper may curl or become damp, resulting
in paper misfeeds.
4. Store a new toner cartridge box horizontally. Do
not store it standing on end. If stored standing on
end, the toner may not distribute well even after
shaking the cartridge vigorously, and will remain
inside the cartridge without flowing out.
Supply and Consumables
The supply of spare parts for a repair of the appliance is guaranteed for at least 7 years following the termination
of production. Spare parts are those parts of the apparatus which may break down within the scope of the ordinary
use of the product - whereas those parts which normally exceed the life of the product are not to be considered
as spare parts. Consumables too, are available for 7 years following the termination of production.
2-22
dragonII_copy_sec.book
23 ページ
２００６年１０月１８日　水曜日　午後７時３９分
MISFEED REMOVAL
When a misfeed has occurred during printing, the message "A MISFEED HAS OCCURRED". will appear in the touch
panel display of the operation panel and printing including copying and facsimile output will stop. The approximate
misfeed locations are indicated with " " shown in the illustration below. The page numbers for detailed information
on misfeed removal are also shown.
1
Misfeed in the transport area, fusing
area, and exit area (See page 2-24)
2
Misfeed in the automatic document
feeder (See page 2-31)
3
When feeding paper from tray 2, the
bypass tray, or tray 5, this mark may
blink. When the mark blinks, check the
following diagrams:
● Fourth diagram in step 3 on page 2-26
● Diagram in step 6 on page 2-27
● Diagram in step 8 on page 2-29, 2-30
4
Misfeed in the bypass tray (See page 2-28)
5
Misfeed in the finisher (See page 3-11)
6
Misfeed in the saddle stitch finisher
(See page 3-11)
7
Misfeed in the inserter (See page 3-17)
8
Misfeed in the tray 3 (See page 2-27)
9
Misfeed in the tray 4 (See page 2-27)
10
Misfeed in tray 1 - tray 2
(See page 2-26)
11
Misfeed in the tray 5 (See page 2-29, 2-30)
NOTE
Printing is not possible when a misfeed occurs, and thus any faxes or Internet faxes received at this time will be
temporarily held in memory. The faxes will print out automatically as soon as the misfeed is cleared.
NOTES
● Do not damage or touch the photoconductive
drum. (See page 2-24.)
● Be careful not to tear the misfed paper during
removal.
● lf paper is accidentally torn during removal, be
sure to remove all pieces.
CAUTION
The fusing unit is hot. Take
care in removing paper.
Fusing unit
Misfeed removal guidance
Misfeed removal guidance can be displayed by touching the [INFORMATION] key on the touch panel after a misfeed
has occurred.
INFORMATION
2-23
2
dragonII_copy_sec.book
24 ページ
２００６年１０月１８日　水曜日　午後７時３９分
MISFEED REMOVAL
Misfeed in the transport area, fusing area, and exit area
CAUTION
Misfed in the fusing area
Turn roller rotating knob
B in the direction of the
arrow to remove the
misfed paper.
o
The fusing unit is hot. Take care in removing paper.
(Do not touch the metal parts.)
1 Remove the duplex unit.
Grasp the finger hold
and gently open the unit.
Roller rotating knob B
CAUTION
The fusing unit is hot. Take care in removing paper.
(Do not touch any metal parts.)
2
Remove the misfed paper as shown in the
illustrations below.
Misfed in the transport area
Turn roller rotating knob
A in the direction of the
arrow to remove the
misfed paper.
Fusing unit open tab
If the misfed paper is
inside the fusing area,
turn down the fusing unit
open tab to open the
fusing unit and remove
the misfed paper.
Roller rotating knob A
NOTES
Do not touch or
damage the transfer
roller.
Misfed in the exit area
Transfer roller
Do not touch or
damage
the
photoconductive
drum.
After clearing the
misfeed,
promptly
Photoconductive drum
close the duplex unit.
Leaving the unit
open may adversely affect the photo-sensitive drum
and cause poor copy quality.
2-24
Be careful not to tear the
misfed paper during
removal.
3 Gently close the duplex unit.
After closing, confirm
that
the
misfeed
message has been
cleared and the normal
display appears.
dragonII_copy_sec.book
25 ページ
２００６年１０月１８日　水曜日　午後７時３９分
MISFEED REMOVAL
Misfeed in the duplex unit
1 Remove the duplex unit.
4 Close the cover of the duplex unit.
Grasp the finger hold
and gently open the unit.
2 Open the cover of the duplex unit.
5 Gently close the duplex unit.
After closing the duplex
unit, confirm that the
misfeed message has
been cleared and the
normal display appears.
the misfed paper.
3 Remove
Misfeed in upper part of unit
Be careful not to tear the
misfed paper during
removal.
Misfeed in lower part of unit
Be careful not to tear the
misfed paper during
removal.
2-25
2
dragonII_copy_sec.book
26 ページ
２００６年１０月１８日　水曜日　午後７時３９分
MISFEED REMOVAL
Misfeed in the paper feed area
NOTE
Be sure to follow the misfeed removal sequence. Do not pull the tray out immediately as the misfeed may have
occurred with paper partially fed out of the tray. Open the left cover and see if there is misfed paper first (steps 1
and 2). If you open the tray without checking, the partially fed paper may tear and leave torn pieces in the machine,
increasing the difficulty of removal.
■ Misfeed in paper tray 1 - tray 2
1 Remove the duplex unit.
●If paper is misfed in tray 2 (right-side tray)...
Grasp the finger hold
and gently open the unit.
2
Remove the misfed paper.
Turn roller rotating knob
A in the direction of the
arrow to remove the
misfed paper.
When using tray 2,
check the paper transfer
unit inside the tray and
remove any misfed
paper.
4 Gently close paper tray 1 - tray 2.
Roller rotating knob A
Push the tray all the way
back in.
NOTE
A misfeed may occur inside the compartment, so
please check the entire compartment carefully.
paper is not found in step 2, pull
3 Ifoutmisfed
paper tray 1 - tray 2 and remove the
misfed paper.
Grasp the finger hold
and gently open the unit.
Pull the tray all the way
out until it stops.
●If paper is misfed in tray 1 (left-side tray)...
Lift the paper guide and
remove
the
misfed
paper.
Be sure to replace the
paper guide in its
original position after
removing the paper.
2-26
5 Gently close the duplex unit.
After closing, confirm
that
the
misfeed
message has been
cleared and the normal
display appears.
dragonII_copy_sec.book
27 ページ
２００６年１０月１８日　水曜日　午後７時３９分
MISFEED REMOVAL
■ Misfeed in paper tray 3
1 Remove the duplex unit.
the lower cover on the left side of
5 Close
the machine.
Grasp the finger hold
and gently open the unit.
2 Remove the misfed paper.
Turn roller rotating knob
A in the direction of the
arrow to remove the
misfed paper.
misfed paper is not found in step 3, pull out
6 Ifpaper
tray 3 and remove the misfed paper.
Pull the tray all the way
out until it stops.
Check the
paper
transfer unit inside the
tray.
Be careful not to tear the
misfed paper during
removal.
Roller rotating knob A
the lower cover on the left side of the
3 Open
machine.
7 Gently close paper tray 3.
Grasp the finger hold
and gently open the unit.
4 Remove the misfed paper.
Push the tray all the way
back in.
8 Gently close the duplex unit.
Be careful not to tear the
misfed paper during
removal.
After closing, confirm
that
the
misfeed
message has been
cleared and the normal
display appears.
NOTE
A misfeed may occur inside the compartment, so
please check the entire compartment carefully.
■ Misfeed in the tray 4
To remove a misfeed in tray 4, follow the same steps as in "Misfeed in paper tray 3".
2-27
2
dragonII_copy_sec.book
28 ページ
２００６年１０月１８日　水曜日　午後７時３９分
MISFEED REMOVAL
■ Misfeed in the bypass tray
the misfed paper from the bypass
1 Remove
tray.
Be careful not to tear the
misfed paper during
removal.
did not find a misfeed in step 1, open
2 Iftheyouside
cover and remove the misfeed.
3 Gently close the side cover.
4 Remove tray 1 - tray 2.
Grasp the finger hold
and gently open the unit.
Pull the tray all the way
out until it stops.
NOTE
If a misfeed occurs during printing from the bypass
tray while paper is being loaded in tray 1 - tray 2,
push tray 1 - tray 2 back in to close it, and then pull
the tray out again.
2-28
5 Remove the misfed paper.
Check the
paper
transfer unit inside the
tray and remove any
misfed paper.
6 Gently close paper tray 1 - tray 2.
Push the tray all the way
back in.
Make sure that the
misfeed message no
longer appears (the
normal message display
should appear).
dragonII_copy_sec.book
29 ページ
２００６年１０月１８日　水曜日　午後７時３９分
MISFEED REMOVAL
■ Misfeed in the tray 5 (AR-LC6)
1 Open the side cover.
the top cover and remove the misfed
6 Open
paper.
After
removing
the
misfed paper, close the
top cover.
2 Remove the misfed paper.
Be careful not to tear the
misfed paper during
removal.
3 Gently close the side cover.
2
7 Remove tray 1 - tray 2.
Grasp the finger hold
and gently open the unit.
Pull the tray all the way
out until it stops.
NOTE
If a misfeed occurs in the following situation, push
tray 1 - tray 2 back in to close it and then pull the tray
out again:
● A misfeed occurs during printing from tray 5 while
paper is being loaded in tray 1 or tray 2.
8 Remove the misfed paper.
4 Close the bypass tray.
Check the
paper
transfer unit inside the
tray and remove any
misfed paper.
9 Gently close paper tray 1 - tray 2.
5 Open the top cover of tray 5.
Push the tray all the way
back in.
Make sure that the
misfeed message no
longer appears (the
normal message display
should appear).
2-29
dragonII_copy_sec.book
30 ページ
２００６年１０月１８日　水曜日　午後７時３９分
MISFEED REMOVAL
■ Misfeed in the tray 5 (AR-LC7)
If a paper misfeed occurs, follow the steps below to remove the misfeed.
1 Open the side cover.
6 Remove the misfed paper.
Be careful not to tear
the
misfed
paper
during removal.
After removing the
misfed paper, close the
top cover.
2 Remove the misfed paper.
7 Pull out tray 1 - tray 2.
Be careful not to tear
the
misfed
paper
during removal.
Grasp the finger hold
and gently open the
tray.
Pull the tray all the way
out until it stops.
3 Gently close the side cover.
NOTE
If a misfeed occurs in the following situation, push tray
1 - tray 2 back in and then pull the tray out again:
● A misfeed occurs during printing from tray 5 (ARLC7) while paper is being loaded in tray 1 - tray 2.
8 Remove the misfed paper.
Check the
paper
transfer unit inside the
tray. If there is a
misfeed in the paper
transfer unit, remove
the misfeed.
4 Close the bypass tray.
9 Gently push tray 1-tray 2 into the machine.
5 Open the top cover of the AR-LC7 (tray 5).
Hold the top cover
open.
2-30
Push the tray firmly all
the way into the
machine.
Make sure that the
misfeed message no
longer appears (the
normal
message
display should appear).
dragonII_copy_sec.book
31 ページ
２００６年１０月１８日　水曜日　午後７時３９分
REMOVING AN ORIGINAL MISFEED
Removing a misfed original from the automatic document feeder
If an original misfeed occurs in the automatic document feeder, follow the steps below to remove the misfed original.
NOTES
● For misfeed removal in the main unit and other peripheral devices, see page 2-23
● When a misfeed occurs, touch the [INFORMATION] key to display detailed information for misfeed removal.
Check locations A and B in the diagram at left to
remove the original.
2
1 Removing misfeeds from each location.
● Check location A
Open the document
feeder cover and gently
remove
the
misfed
original without tearing
it. Close the document
feeder cover.
and
2 Open
cover.
close the document feeder
Opening and closing the
cover clears the misfeed
display. Copying cannot
be resumed until this
step is performed.
However, this step is not
necessary
after
a
misfeed is removed from location B.
A message may appear indicating the number of
originals which must be returned to the document
feeder tray. Return the originals to the document
feeder tray and press the [START] key.
● Check location B
● Misfeed in the transfer unit
Open the document
transfer cover, hold the
paper guide open, and
remove
the
misfed
original.
● Misfeed in the document exit unit
Open the document
transfer cover. Rotate
the transfer roller in the
direction of the arrow
and gently remove the
original without tearing
it.
2-31
dragonII_copy_sec.book
32 ページ
２００６年１０月１８日　水曜日　午後７時３９分
TROUBLESHOOTING
Check the following troubleshooting list before requesting service as many problems can be fixed by the user. If you
are unable to solve the problem by checking the list, turn off the main power switch and the power switch, unplug the
power cord.
Problems related to general use of the machine are described below. For problems related to the copy function, see
page 6-3. For problems related to document filing, see page 7-31. For fax, printer, and network scanner/Internet fax
problems, see the manuals for those functions. For peripheral device problems, see the explanation of the device.
If the message "CALL FOR SERVICE. CODE:**-**"(Note) appears in the touch panel, turn off the main power switch
and the power switch, wait about 10 seconds, and then turn the main power switch and the power switch back on.
If the message still appears after turning the main power switch and the power switch off and on several times, it
is likely that a failure has occurred that requires service. In this event, stop using the machine, unplug the power
cord, and contact your Sharp dealer.
Note: Letters and numbers appear in "**-**". When you contact your Sharp dealer, please tell your dealer what
letters and numbers appear.
Problem
Check
Solution or cause
Machine plugged in?
Plug the machine into a grounded outlet.
The main power switch and power
switch are not turned on?
Turn on the main power switch and the power
switch. (Page 1-17)
READY indicator off?
The printer is warming up. (Warm-up time is
approximately 120 seconds.) Wait until the
READY indicator lights up.
Message indicating need to load paper
displayed?
Load paper. (Page 2-2)
Message indicating need to replace the
toner cartridge displayed?
Replace the toner cartridge. (Page 2-21)
Message indicating a paper misfeed
displayed?
Remove misfed paper. (Page 2-23)
Copying/printing is
not possible.
A message appears saying that this type
of paper cannot be used for two-sided
copying.
Two-sided printing is not possible on special
paper. Use paper that can be used for automatic
two-sided printing. (Page 2-13)
Incorrect
bypass
tray paper size.
Incorrect display of paper sizes 11" x 17",
8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11"R,
A3, B4, or A4R only.
When loading sizes 11" x 17", 8-1/2" x 14", 8-1/
2" x 13", 8-1/2" x 11"R, A3, B4, or A4R, be sure
to open the tray extension.
The number of sheets placed on the bypass
tray exceeds the maximum number.
Do not place more than the maximum number of
sheets.
The bypass guide is not adjusted to the
size of the loaded paper.
Adjust the bypass guide to the size of the loaded
paper.
The machine does
not operate.
Copying/printing on
paper from the
bypass
tray
is
skewed.
2-32
dragonII_copy_sec.book
33 ページ
２００６年１０月１８日　水曜日　午後７時３９分
TROUBLESHOOTING
Problem
Paper from
bypass
misfeeds.
the
tray
Printing
stops
before the job is
finished.
Check
Solution or cause
The paper size and paper type have not
been set.
Be sure to set the paper size and paper type
when using special size or special type papers.
(Page 2-14)
The number of sheets placed on the bypass
tray exceeds the maximum number.
Do not place more than the maximum number of
sheets.
The bypass guide is not adjusted to the
size of the loaded paper.
Adjust the bypass guide to the size of the loaded
paper.
If too many pages collect on the output
tray, the tray full sensor activates and Remove the paper from the output tray.
stops printing.
2
The paper tray is out of paper.
Load paper. (Page 2-2)
Smudges on printed
sheets
Does a message appear indicating the
need for maintenance?
Please contact your dealer as soon as possible.
The displayed paper
size or paper type
does not match the
loaded paper size or
paper type.
When loading paper, if you change the paper
size from an inch size to an AB size, or from an
The correct paper size or paper type is
AB size to an inch size, or change the paper
not set in the paper tray settings of the
type, be sure to set the new paper type as
system settings.
explained in "Setting the paper type and paper
size" (see page 2-14).
When printing on a
special
size
of
paper, part of the
printed image is
missing.
The paper size setting is not set
correctly in the paper tray settings of the
system settings.
When using a special size of paper, set the
correct paper size as explained in "Setting the
paper type and paper size" on page 2-14. If the
paper size setting is not correct, part of the image
may be cut off or the image may not be printed.
The paper size is not set correctly in the
special size settings for the bypass tray.
When using a special size of paper, set the
correct paper size as explained in "Setting the
paper type and paper size" on page 2-14. If the
paper size setting is not correct, part of the image
may be cut off or the image may not be printed.
Is
paper
other
than
SHARPrecommended paper being used?
Use SHARP-recommended paper. (Page 2-22)
Paper curled or damp?
Do not use curled or crimped paper. If you will
not use the paper for a long time, remove the
paper from the tray and store it in the wrapper in
a cool and dark location so that it will not absorb
moisture.
Is the paper curled and does it
frequently misfeed in the finisher or
saddle stitch finisher?
Paper may be curled when output depending on
the paper type and quality.
In some cases turning the paper over in the tray
will reduce misfeeding due to curling.
When printing on a
special size of paper
using the bypass
tray, part of the
printed image is
missing.
Paper
misfeeds
frequently.
fed
Remove the paper
from the paper
tray or the bypass
tray, fan the paper
as shown in the
illustration,
and
then load it again.
The paper in the tray is not stacked
evenly.
Make sure that the paper in the paper tray is
stacked evenly. If the stack is not even, paper
misfeeds will occur.
Multiple
sheets
simultaneously?
of
paper
2-33
dragonII_copy_sec.book
34 ページ
２００６年１０月１８日　水曜日　午後７時３９分
TROUBLESHOOTING
Problem
Printed paper is
wrinkled or the
image
rubs
off
easily.
The contrast on the
touch panel is too
high or too low.
Printing takes place
on the wrong side of
the paper.
Marks appear at
regular intervals on
printed pages.
2-34
Check
Solution or cause
Is
paper
other
than
SHARPrecommended paper being used?
Use SHARP-recommended paper. (Page 2-22)
Is the paper size or weight outside the
specifications?
Use paper within the specifications.
Paper damp?
Be sure to store paper in the wrapper in a dry
location and do not store paper in a location that is
●humid
●at a high temperature or an extremely low
temperature
●exposed to direct sunlight
●dusty.
Is LCD contrast properly adjusted?
Adjust the screen contrast using "DISPLAY
CONTRAST" in "DEFAULT SETTINGS" of the
system settings. (Page 2-20)
The paper is loaded in the tray with the
print side face down*.
* Face up if the paper type is "PREPRINTED" or "LETTER HEAD".
Load paper in the tray with the print side face up.
However, if the paper type is "PRE-PRINTED" or
"LETTER HEAD", load the paper with the print
side face down*.
* If the two-sided function has been prohibited
using "DISABLING OF DUPLEX" in the
administrator settings (page 11 of the
administrator settings guide), load the paper
face up.
Paper with punch holes is being used.
If the original image overlaps the punch holes,
marks will appear at the position of the holes on
the back of the paper after one-sided printing, or
on the front and back of the paper after two-sided
printing. Make sure that the original image does
not overlap the punch holes.
dragonII_copy_sec.book
1 ページ
２００６年１０月１８日　水曜日　午後７時３９分
CHAPTER 3
PERIPHERAL DEVICES
This chapter explains the procedures for using the optional finisher,
saddle stitch finisher, and inserter, as well as Sharp OSA (application
communication module and external account module).
Page
FINISHER AND SADDLE STITCH FINISHER........................................ 3-2
● Part names...................................................................................... 3-2
● Specifications .................................................................................. 3-2
● Finishing methods ........................................................................... 3-4
● Finishing modes and finisher functions ........................................... 3-6
● Staple cartridge replacement and staple jam removal .................... 3-7
● Removing a misfeed........................................................................ 3-11
● Troubleshooting finisher/saddle stitch finisher problems ................. 3-13
INSERTER .............................................................................................. 3-14
● Part names...................................................................................... 3-14
● Specifications .................................................................................. 3-14
● Loading paper ................................................................................. 3-15
● Manual operation of the inserter ..................................................... 3-15
● Misfeed removal .............................................................................. 3-17
● Troubleshooting inserter problems .................................................. 3-18
SHARP OSA ........................................................................................... 3-19
APPLICATION COMMUNICATION MODULE (MX-AMX2)..................... 3-19
● Standard application setup.............................................................. 3-19
● Selecting a standard application ..................................................... 3-19
● Operation in OSA mode .................................................................. 3-20
EXTERNAL ACCOUNT MODULE (MX-AMX3) ...................................... 3-21
● External account application setup ................................................. 3-21
● Operation in external account mode ............................................... 3-21
3-1
dragonII_copy_sec.book
2 ページ
２００６年１０月１８日　水曜日　午後７時３９分
FINISHER AND SADDLE STITCH FINISHER
The finisher and the saddle stitch finisher include the offset function, which offsets each set of copies from the
preceding set for easy separation. Each set of sorted copies can also be stapled. The saddle stitch finisher can
automatically staple a set of copies at the center line and fold the pages to create a pamphlet.
A punch module unit can be installed to add punch holes to copies, and an inserter can be installed to insert blank
pages at specified pages.
In the following explanations, the finisher and saddle stitch finisher are referred to simply as "finisher".
Part names
1
2
3
Finisher
(AR-F15)
4
Saddle stitch
finisher (AR-F16)
5
6
7
Saddle stitch finisher
(AR-F16)
Finisher (AR-F15)
*
Tray
Offset pages and stapled
pages are delivered here.
Stapler compiler
Paper to be stapled is stacked
temporarily.
Top cover
Open for misfeed removal.
Punch module (Option)
Adds punch holes to printed pages.
Front cover
Open to replace the staple
case in the staple unit or clear
jammed staples.
Lower cover
Open to clear misfed paper or
replace the staple cartridge in the
pamphlet unit. (AR-F16 only)
Saddle stitch tray
Saddle stitched output is
delivered here.
(AR-F16 only)
The illustrations on the following pages (to page 3-18) show the AR-F16; however, the operation of the AR-F15
is the same as the AR-F16.
NOTES
● Do not press on the finisher.
● Use caution when near the offset tray during printing as the tray moves up and down.
Specifications
Name
Number of trays
Paper output
Paper capacity
3-2
Finisher (AR-F15)
2
Saddle stitch finisher (AR-F16)
3
Face down output
Upper paper tray/Middle paper tray:
Upper paper tray/Middle paper tray:
Non-stapling:
Non-stapling:
2000 sheets of paper or total aggregate 2000 sheets of paper or total aggregate thickness
thickness is within 9-53/64" (250mm):
is within 9-53/64" (250mm): 8-1/2" x 11", 5-1/2" x
8-1/2" x 11", 5-1/2" x 8-1/2"R, A4, B5 or A5R 8-1/2"R, A4, B5 or A5R (20 lbs. (80 g/m2))
(20 lbs. (80 g/m2))
1000 sheets of paper or total aggregate thickness is
1000 sheets of paper or total aggregate within 5-1/2" (140mm): Sizes other than the above
thickness is within 5-1/2" (140mm):
Stapling:
Sizes other than the above
100 sets or 750 pages or total aggregate thickness is
Stapling:
within 4-5/16" (110mm) of 8-1/2" x 11", A4 or B5 paper.
100 sets or 750 pages of 8-1/2" x 11", A4 100 sets or 500 pages or total aggregate thickness
or B5 paper.
is within 2-29/32" (74mm) of other sizes of paper
100 sets or 500 pages of other sizes of Lower tray:
paper
Stapled print capacity is (11 - 15) sheets x 10 sets, (6
- 10) sheets x 20 sets, (1 - 5) sheets x 25 sets.
(Continued on next page)
dragonII_copy_sec.book
3 ページ
２００６年１０月１８日　水曜日　午後７時３９分
FINISHER AND SADDLE STITCH FINISHER
Paper size
Paper weight
Paper full detection
Paper sizes for which
offset is possible
Allowed paper sizes for
stapling
Maximum number of
sheets for stapling
Stapling positions
Paper conveying
Power supply
Dimensions
Weight
Overall dimensions when
attached to machine
Upper paper tray/Middle paper tray:
11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2"
x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 51/2" x 8-1/2"R, A3, B4, A4, A4R, B5, B5R,
A5R
Upper paper tray/Middle paper tray:
16 to 68* lbs. (60 to 256 g/m2)
Both upper and lower tray
Upper paper tray/Middle paper tray:
11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x
11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2"
x 8-1/2"R, A3, B4, A4, A4R, B5, B5R, A5R
Lower tray:
11" x 17", 8-1/2" x 11"R, A3, B4, A4R
Upper paper tray/Middle paper tray/Lower tray:
16 to 68* lbs. (60 to 256 g/m2)
Upper, middle and lower tray
11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, A3, B4, A4, A4R, B5
Upper paper tray/Middle paper tray:
11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2"
x 11", 8-1/2" x 11"R, A3, B4, A4, A4R, B5
Upper paper tray/Middle paper tray:
11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x
11", 8-1/2" x 11"R, A3, B4, A4, A4R, B5
Lower tray:
11" x 17", 8-1/2" x 11"R, A3, B4, A4R
See "Staple sort mode" on 3-4 page
1 place at back, 1 place at back (diagonal), one place at front (diagonal), 2 places
Center reference
Supplied from machine
When tray is folded up: 25-33/64" (W) x 24-13/16" (D) x 45-9/32" (H)
(648 mm (W) x 630 mm (D) x1150 mm(H))
When tray is extended: 30-7/16" (W) x 24-13/16" (D) x 45-9/32" (H)
(773 mm (W) x 630 mm (D) x1150 mm(H))
Not including stopper (1-37/64" (40 mm)) when attached to machine
Approx. 113 lbs. (Approx. 51 kg)
Approx. 157 lbs. (Approx. 71 kg)
30-7/16" (W) x 24-13/16" (D) (Separation from machine 15-3/4")
(773 mm (W) x 630 mm (D) (Separation from machine 400 mm))
*For index paper, equivalent to 140-lbs.
Name
Hole punching
Allowed paper sizes for
punching
Page weight
Power supply
Dimensions
Weight
Punch module (AR-PN4B)
3 holes
11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, A3, B4, A4, A4R, B5,
B5R
16 to 68* lbs. (60 to 256 g/m2)
Supplied from finisher / saddle stitch finisher
3-3/4" (W) x 22-1/16" (D) x 6-45/64" (H) (95 mm (W) x 560 mm (D) x 170 mm (H))
Approx. 7.8 lbs. (Approx. 3.5 kg)
* For index paper, equivalent to 140-lbs.
Specifications are subject to change for improvement without notice.
NOTES
● The following papers cannot be stapled and punched:
Special papers such as transparency film and label sheets
● If mixed paper sizes are selected for stapling jobs, stapling will be automatically canceled.
■ Supplies
The finisher and saddle stitch finisher require the following staple cartridge:
● Staple cartridge for finisher
(approx. 5,000 per cartridge
X 3 cartridges)
SF-SC11
● Staple cartridge for saddle
stitch finisher (approx. 2000
per cartridge X 3 cartridges)
AR-SC3
3-3
3
dragonII_copy_sec.book
4 ページ
２００６年１０月１８日　水曜日　午後７時３９分
FINISHER AND SADDLE STITCH FINISHER
Finishing methods
■ Sort mode
■ Offset mode
Sorted sets will be delivered.
Offset mode
Original
Printouts
■ Group mode
Groups of copies of the same page will be
delivered.
Original
Non-offset mode
Printouts
Each set of copies is offset from the preceding set to
allow easy separation.
(The offset function operates in the finisher / saddle
stitch finisher tray.)
The offset function cannot be selected when the
staple sort function is selected.
Offset width : Approx. 1-3/16" (Approx. 30 mm)
■ Staple sort mode
Output pages are sorted into sets by the sort function, and each set is stapled and delivered to the tray. The center
of the paper can also be stapled and delivered to the lower saddle tray (only when using the saddle stitch finisher).
The relations between possible stapling positions, the paper feed direction, paper sizes that can be used, and
number of pages that can be stapled are shown below.
Two sheets (one sheet when using the saddle stitch function) of 68 lbs. (256 g/m2) paper can be included as
covers in the page stapling limit in the table below.
Stapling positions
Top left corner of
printouts
Portrait orientation
Available paper sizes:
8-1/2" x 11", A4 and B5
Stapling capacity:
For each size, up to 50 sheets
can be stapled
Landscape orientation
Available paper sizes:
11" x 17", A3, B4
Stapling capacity:
For each size, up to 30 sheets
can be stapled
Available paper sizes:
8-1/2" x 14", 8-1/2" x 13",
8-1/2" x 11"R, A4R
Stapling capacity:
For each size, up to 30 sheets
can be stapled
Lower left corner
of printouts
Same as above
Available paper sizes:
11" x 17", 8-1/2" x 14",
8-1/2" x 13", 8-1/2" x 11"R, A3,
B4, A4R
Stapling capacity:
For each size, up to 30 sheets
can be stapled
Center left two
positions of
printouts
Same as above
Same as above
Saddle stitch on
centerfold line.
(only when using
the saddle stitch
finisher)
Paper in the portrait
direction cannot be saddle
stitched.
Available paper sizes:
11" x 17", 8-1/2" x 11"R, A3,
B4, A4R
Stapling capacity:
For each size, up to 15 sheets
can be stapled
3-4
dragonII_copy_sec.book
5 ページ
２００６年１０月１８日　水曜日　午後７時３９分
FINISHER AND SADDLE STITCH FINISHER
■ Original orientation when using the staple sort or punch function
When using the staple sort or punch function, the original must be placed in the following orientations to enable
stapling or punching in the desired position on the paper.
Staple sort
Document feeder
Punch
Document glass
Document feeder
Document glass
3
■ Saddle stitch function (only saddle stitch finisher)
The saddle stitch finisher can automatically place
two staples for centerline binding of prints or copies
and fold them along the centerline.
<Example>
6
4
2
7
9
11
■ Hole punching (only if a punch module is installed)
When the optional punch module is installed, holes
can be punched in printed pages. (When using the
saddle stitch finisher, pamphlet style stapling and
the punch function cannot be used together.) When
using the punch function, automatic rotation of the
original image does not operate.
For the allowed paper sizes for punching, see the
specifications on page 3-3.
When using the punch function in copy mode,
place the original with the top toward the inside of
the machine. If the original is not placed in this
orientation, punching will not take place at the
correct positions. (See "Standard original
placement orientations" on page 4-4.)
<Example>
{Original 1}
{Punch positions}
{Original 2}
{Punch positions}
3-5
dragonII_copy_sec.book
6 ページ
２００６年１０月１８日　水曜日　午後７時３９分
FINISHER AND SADDLE STITCH FINISHER
Finishing modes and finisher functions
Touch the [OUTPUT] key on the main screen of copy mode to display the screen that allows selection of sort, staple
sort, group function, centerline stapling, and the output tray.
0
OUTPUT
SORT
FINISHER
TRAY
STAPLE
SORT
GROUP
1
[GROUP] key (See page 3-4.)
SADDLE
STITCH
6
If the center tray is selected, output paper will be
delivered to the exit tray located above the main
unit.
7
[SORT] key (See page 3-4.)
[FINISHER TRAY] key (See page 3-2.)
When the offset function is selected, output is
delivered offset to the finisher tray. (The finisher
tray is automatically selected when the staple sort
function is turned on.)
9
[OFFSET] key (See page 3-4.)
The offset function operates when a checkmark
appears in this key. (The offset checkmark is
automatically cleared when the staple sort function
is enabled.)
3-6
[SADDLE STITCH] key (See page 3-5.)
This is displayed when the saddle stitch finisher is
installed, and is used to staple pages at the center
and fold them in half to create a pamphlet.
Touch this key to display the pamphlet copy
setting screen (page 5-6). (This is only possible
when the [AUTOMATIC SADDLE STITCH]
checkbox is selected in the administrator settings
(see page 12 of the administrator settings guide).)
When Sort is selected, sets of copies will be
collated.
5
[OK] key
Touch to close the [OUTPUT] screen and return to
the main screen.
8
4
[CENTER TRAY] key
[STAPLE SORT] key (See page 3-4.)
When Staple Sort is selected, sorted sets will be
stapled and delivered to the offset tray. (They will
not be offset stacked.) Select from three stapling
positions.
3
PUNCH
OFFSET
When Group is selected, copies will be grouped by
page.
2
OK
CENTER
TRAY
[PUNCH] key (See page 3-5.)
This is used to punch holes in printed pages when
an optional punch module is installed.
NOTE
When a functions is selected, it is highlighted.
dragonII_copy_sec.book
7 ページ
２００６年１０月１８日　水曜日　午後７時３９分
FINISHER AND SADDLE STITCH FINISHER
Staple cartridge replacement and staple jam removal
When a finisher is installed, a message will appear when the staple cartridge runs out of staples or a staple jam
occurs.
Follow the procedure below to replace the staple cartridge or remove jammed staples.
■ Replacing the cartridge in the finisher
1 Open the front cover of the finisher.
the seal that holds the staples straight
5 Pull
out.
3
the blue lever in the stapler and
2 Lower
slide out the staple cartridge.
the cartridge all the way in until it
6 Insert
clicks into place.
Insert the cartridge all
the way in until it clicks
into place.
the empty staple case straight up and
3 Pull
out of the cartridge.
4
Insert a new staple case into the cartridge.
Push the staple case all the way in until it
clicks into place.
7 Close the front cover of the finisher.
NOTE
Make a test print or copy in the staple sort mode to
verify that stapling is performed properly.
Do not remove the seal
holding the staples until
the staple case is set in
the cartridge.
3-7
dragonII_copy_sec.book
8 ページ
２００６年１０月１８日　水曜日　午後７時３９分
FINISHER AND SADDLE STITCH FINISHER
■ Replacing the cartridge in the saddle stitch finisher
Only when the saddle stitch finisher (AR-F16) is installed.
the lower cover of the saddle stitch
1 Open
finisher.
When
an
optional
inserter is installed,
open the front cover of
the
inserter
before
opening the lower cover
of the finisher.
out the saddle stitch unit carefully
2 Slide
toward the front.
the saddle stitch holder and the
5 Return
saddle stitch unit to their respective
original positions.
sure that the finisher is firmly
6 Make
attached to the machine and that 11" x 17",
8-1/2" x 11"R, or 8-1/2" x 14" (A3, A4R, or
B4) size paper is loaded.
If one of the above paper sizes is not set, test
stapling cannot be performed.
7 Close the lower cover of the finisher.
Grasp the grip of the saddle staple
3 (1)
holder and pull it out.
(2) While still grasping the grip, rotate the
saddle staple holder 90° in the direction of
the arrow (rotate to the right).
(2)
Test
stapling
is
automatically performed
on a blank sheet.
This operation is carried
out to avoid blank
stapling.
(1)
NOTE
If test stapling fails to take place, repeat steps 1 to 7.
the empty staple case and set a
4 Remove
new one.
Replace both staple
cases with new ones.
Remove the cover from
the staple cartridge and
then install the cartridge.
3-8
dragonII_copy_sec.book
9 ページ
２００６年１０月１８日　水曜日　午後７時３９分
FINISHER AND SADDLE STITCH FINISHER
■ Removing a staple jam in the finisher
steps 1 to 2 of the procedure for
1 Perform
"Replacing the cartridge in the finisher"
the knob, return part (A) to its
4 Holding
original position.
on page 3-7.
2 Holding the knob, lower part (A).
Stapling area
(A)
(A)
NOTE
Do not touch the stapling area.
The stapler could injure you.
the
5 Return
position.
staple case to its original
Insert the cartridge all
the way in until it clicks
into place.
3 Remove any jammed staples.
6 Close the front cover of the finisher.
3-9
3
dragonII_copy_sec.book
10 ページ
２００６年１０月１８日　水曜日　午後７時３９分
FINISHER AND SADDLE STITCH FINISHER
■ Removing a staple jam in the saddle stitch finisher
steps 1 to 3 of the procedure for
1 Perform
"Replacing the cartridge in the saddle
the
5 Return
position.
staple case to its original
stitch finisher" on page 3-8.
2 Remove the empty staple case.
the saddle stitch holder and the
6 Return
saddle stitch unit to their respective
original positions.
While pushing down on lever (A), pull up
3 knob
(B) .
sure that the finisher is firmly
7 Make
attached to the machine and that 11" x 17",
8-1/2" x 11"R, or 8-1/2" x 14" (A3, A4R, or
B4) size paper is loaded.
(A)
If one of the above paper sizes is not set, test
stapling cannot be performed.
(B)
8 Close the lower cover of the finisher.
4
Remove any jammed staples, and then
return knob (B) to its original position.
(B)
Be sure to remove any
strips of staples.
Test stapling is automatically performed on a blank
sheet.
This operation is carried out to avoid blank
stapling.
NOTE
If test stapling fails to take place, repeat steps 1 to 7.
Jammed staples
NOTE
Do not touch the stapling area.
The stapler could injure you.
■ Disposal of hole punch scrap (when the punch module is installed)
1 Open the cover of the hole punch module.
the black handle, slide out the
2 Holding
case containing the paper bits, and
dispose of them properly.
the
3 Return
position.
waste case to its original
4 Close the cover of the hole punch module.
3-10
dragonII_copy_sec.book
11 ページ
２００６年１０月１８日　水曜日　午後７時３９分
FINISHER AND SADDLE STITCH FINISHER
Removing a misfeed
When a misfeed occurs, remove the misfed paper as explained below.
■ General procedure for the finisher and saddle stitch finisher
move the finisher/saddle stitch
1 Gently
finisher away from the machine while
pressing the button.
When an inserter is
installed, separate the
inserter
from
the
machine while pressing
on the inserter button.
the misfed paper from the main
2 Remove
unit.
any misfed paper from the paper
6 Remove
exit area.
Be careful not to tear the
misfed paper during
removal.
the upper cover
7 Close
saddle stitch finisher.
of the finisher/
3
After
removing
the
misfed paper, perform
steps 1 and 3 on page 224 to reset the machine.
■ When a saddle stitch finisher is installed
the upper cover
3 Open
saddle stitch finisher.
(A)
of the finisher/
the front cover of the inserter (only
8 Open
when an inserter is installed).
When an inserter is
installed, lift the tray of
the inserter.
Lift knob (A) (See the step 3 figure), then
4 remove
any misfed paper.
Be careful not to tear the
misfed paper during
removal.
the lower cover of the saddle stitch
9 Open
finisher.
(B)
knob (B) (see the illustration in step 4)
5 Lift
and remove any misfed paper.
Be careful not to tear the
misfed paper during
removal.
the entrance cover of the saddle
10 Open
stitch unit.
3-11
dragonII_copy_sec.book
12 ページ
２００６年１０月１８日　水曜日　午後７時３９分
FINISHER AND SADDLE STITCH FINISHER
11 Remove the misfed paper.
the lower cover of the saddle stitch
17 Close
finisher.
Be careful not to tear the
misfed paper during
removal.
the entrance cover of the saddle
12 Close
stitch unit.
the front cover of the inserter (only
18 Close
when an inserter is installed).
the right-hand knob
counter
13 Turn
clockwise. Then, push the left-hand knob
■ When a punch module is installed
1
2
and turn it clockwise.
any paper misfed on the exit side
14 Remove
of the saddle stitch unit.
Be careful not to tear the
misfed paper during
removal.
the exit cover of the saddle stitch
15 Open
unit and remove any misfed paper.
Be careful not to tear the
misfed paper during
removal.
the exit cover of the saddle stitch
16 Close
unit.
3-12
19 Open the cover of the hole punch module.
the green knob until the arrow is
20 Rotate
within the range (A) on the label, and
remove the misfed paper.
(A)
Be careful not to tear the
misfed paper during
removal.
21 Close the cover of the hole punch module.
the finisher back against the main
22 Push
unit.
dragonII_copy_sec.book
13 ページ
２００６年１０月１８日　水曜日　午後７時３９分
FINISHER AND SADDLE STITCH FINISHER
Troubleshooting finisher/saddle stitch finisher problems
Check the list below before calling for service.
Problem
Check
Solution or cause
Stapling position is
not
correct
Stapling position not set properly?
(including
saddle
stitch).
Check the stapling position setting. (See page
3-4.)
Are any finisher/saddle stitch finisher
The finisher/saddle covers open?
stitch finisher does
Message indicating need to remove paper
not operate.
from the stapler compiler displayed?
Message to
displayed?
check
the
staple
unit
Message to add staples displayed?
Stapling cannot be
performed (including
Different sizes of paper mixed together?
saddle stitch).
The paper is badly curled.
Close all covers. (See step 7 on page 3-7 and
step 7 on page 3-11.)
Remove all remaining paper from the stapler
compiler. (For the stapler compiler, see "Part
names" on page 3-2.)
Remove jammed staples. (See pages 3-9 and
3-10.)
Replace the staple cartridge. (See pages 3-7
and 3-8.) Check that a staple cartridge has
been installed. (See pages 3-7 and 3-8.)
Stapling cannot be performed on mixed paper
sizes.
The quality and type of some papers may
cause bad curling that prevents stapling.
Take the paper out of the tray or bypass tray,
turn the stack over, and reload it.
Saddle stitch cannot The paper type of the selected paper tray
be selected.
is set to heavy paper.
Saddle stitch is not possible on heavy paper.
However, when cover insertion is selected,
saddle stitch is possible on a single sheet of
heavy paper inserted for use as a cover.
The punch hole
The punch function is not set to the correct
positions are not
punch positions.
correct.*
Check the allowed hole punch positions. (See
page 3-5.)
Message to check the punch module
displayed?
Dispose of punch scraps. (See page 3-10.)
Mixed paper sizes.
Punching is not possible when different paper
sizes are mixed together.
The paper is badly curled.
The quality and type of some papers may
cause bad curling that prevents punching.
Take the paper out of the tray or bypass tray,
turn the stack over, and reload it.
Cannot be punched.*
* When a hole punch module is installed
3-13
3
dragon_03.fm
14 ページ
２００６年１１月２９日　水曜日　午後８時４７分
INSERTER
The inserter enables blank sheets or printed sheets to be added to copy and print output as covers or inserts
without printing. The inserter also allows feeding of heavy paper that cannot be fed from the other trays.
Printed output can also be fed one set at a time from the inserter for stapling or punching without performing
stapling or staple sorting finishing (see "Manual operation of the inserter" (page 3-15)).
When feeding from the inserter for pamphlet copying (page 5-6), cover or insert copying (page 5-12), or
transparency insert copying (page 5-23), select "INSERTER" in step 4 of "Setting the paper type and paper size"
(page 2-14), and be sure to perform steps 5 through 8. In step 9, make sure that the checkboxes below "PRINT",
"COPY", and "DOC. FILING" are selected. If any of these checkboxes are not selected, touch them so that a
checkmark appears.
When feeding from the inserter for pamphlet copying (page 5-6), cover or insert copying (page 5-12), or
transparency insert copying (page 5-23), select the inserter in the tray settings. The inserter attributes can also
be selected in the system settings (see page 2-18).
Part names
1
Paper tray
Place blank or printed paper here to be inserted.
2
Paper guide
When loading paper, adjust this guide to the width of the paper.
3
Top cover
Open for misfeed removal.
4
Inserter operation panel
Stapling and punching can be performed directly
from the inserter operation panel without using the
machine operation panel.
5
Paper guide lever
Release the paper guide lock to remove misfed paper.
6
Front cover
Open this cover to remove misfed paper from the
finisher or saddle stitch finisher.
NOTE
To install the inserter...
An optional finisher or saddle stitch finisher must be installed (page 3-2).
Specifications
Name
Paper weight
Paper types
Paper size
Paper capacity
Paper conveying
Power supply
Dimensions
Weight
Inserter (AR-CF2)
16 lbs. to 68* lbs. (60 to 256 g/m2) *For index paper, equivalent to 140-lbs.
Plain paper, special paper (transparency film, colored paper, paper with punch holes,
tabbed paper, etc.)
(Consult your retailer for more information on special papers that can be used.)
1 1 " x 1 7 " , 8 - 1 / 2 " x 1 4 " , 8 - 1 / 2 " x 1 3 ", 8 - 1 / 2 " x 1 1 " , 8 - 1 / 2 " x 1 1 " R , 7 - 1 / 4 " x
10-1/2"R, 5-1/2" x 8-1/2"R, A3, B4, A4, A4R, B5, B5R, A5R
Max. 100 (20 lbs. (80 g/m2))
Center reference
Supplied from machine
When paper tray is folded up: 11-15/64" (22-1/4"*) (W) x 23-3/64" (D) x 44-7/64" (H)
(285 (565*) mm (W) x 585 mm (D) x 1120 mm (H))
Not including stopper ( 1-37/64"(40 mm)) when attached to machine
* Including paper tray
Approx. 53 lbs. (Approx. 24 kg)
Specifications are subject to change for improvement without notice.
3-14
dragonII_copy_sec.book
15 ページ
２００６年１０月１８日　水曜日　午後７時３９分
INSERTER
Loading paper
When loading paper in the inserter, load the paper face up. If the paper has a top edge and bottom edge, load in
the same top-bottom orientation as the original. Adjust the paper guide on the paper tray to the width of the paper.
When using tabbed paper, place the paper as follows:
Load the paper back
side up.
The top side is
inserted first.
Back side
The relation of copies and tabbed sheets is shown below.
Copy
Load tabbed paper
Back
side
Back
side
Inserted first.
1st sheet
1st sheet
Back
side
2nd sheet
3rd sheet
4th sheet
5th sheet
4th sheet
5th sheet
Back
side
Tabbed paper 4th sheet (back side)
Copy result
Tabbed paper 1st sheet (back side)
Manual operation of the inserter
The inserter can be used for stapling or punching without performing a copy operation. These functions are selected
at the operation panel of the inserter.
1
2
[PUNCH] key
When a punch module is installed on the finisher
or saddle stitch finisher, punch holes can be
added to blank paper or printed paper. The
indicator lights when this function is selected.
[STAPLE] key/indicator
When this function is selected, each set of output
is stapled and delivered to the finisher or saddle
stitch finisher tray. (Note that the sets are not
offset.) Press this key until the icon light of the
desired staple position lights up. (" " pamphlet
stapling can only be selected when a saddle stitch
finisher is installed)
3
[START] key/indicator
After selecting punch or staple settings with key 1
or key 2 , place the paper to be punched or
stapled on the inserter tray and press this key.
NOTES
● Do not use tabbed paper when operating the inserter manually.
● The punching and stapling functions cannot be used when the finisher or saddle stitch finisher has failed, or
when the functions are prohibited* in the administrator settings (page 11 of the administrator settings guide).
* Disabling of stapler/Disabling of punch/Disabling of finisher/Disabling of inserter
3-15
3
dragonII_copy_sec.book
16 ページ
２００６年１０月１８日　水曜日　午後７時３９分
INSERTER
■ Alarm display
If the [START] key indicator on the inserter operation panel is blinking and the [PUNCH] key or [STAPLE] key
indicator is also blinking or solidly lit, operation will not start when the [START] key is pressed. Resolve the
problem as indicated below, depending how the indicators are lit or blinking.
[PUNCH]
indicator
[START]
indicator
[STAPLE] indicator
Any one of the indicators is solidly lit.
-
Blinking
-
-
-
-
-
-
-
Solidly
lit
-
-
Any one of the
indicators is blinking.
-
-
-
Blinks red
-
Blinking
Blinks red
Blinks red
Blinks red
Blinks red
Cause
Solution
A paper size that cannot
be fed has been loaded.
Use paper that is a suitable
size for punching, stapling, or
saddle stitching (page 3-3).
The paper type of the
inserter is set to heavy
paper.
Heavy paper cannot be
used.
The finisher or saddle
stitch finisher tray is full.
Remove the paper from
the tray.
Discard the hole punch
The hole punch scrap
scrap (page 3-10).
container in the punch
module on the finisher or
saddle stitch finisher is full.
The finisher or saddle
stitch finisher tray is full.
Remove the paper from
the tray.
The finisher or saddle
stitch finisher is out of
staples.
Replace the staple
cartridge (page 3-7).
The saddle stitch tray on
the saddle stitch finisher is
full.
Remove the paper from
the saddle stitch tray.
The saddle stitch finisher is Replace the saddle stitch
out of saddle stitch staples. staple cartridge (page 38).
■ Using the inserter
For paper sizes that can be stapled or punched, see the finisher and saddle stitch finisher specifications on
page 3-2.
Some paper types cannot be stapled or punched (see "NOTES" on page 3-3). Do not use these paper types.
1 Load paper in the inserter.
Paper guide
Load the paper face up.
When
performing
pamphlet stapling, place
the paper so that the
opened pages are face
up as shown.
Adjust the paper guide
to the size of the paper.
2 Press the desired mode key.
Press key 2 on page 3-15 for stapling or pamphlet
stapling. Press key 1 on page 3-15 for punching.
The selected mode lights up.
3-16
NOTE
Pamphlet stapling can only be used when the saddle
stitch finisher (AR-F16) is installed.
When using pamphlet stapling, stapling and
punching cannot be used in combination.
3 Press the [START] key.
Make sure that the
[START] key light is
illuminated green and
then press the [START]
key.
dragonII_copy_sec.book
17 ページ
２００６年１０月１８日　水曜日　午後７時３９分
INSERTER
Misfeed removal
When a misfeed occurs in the inserter, remove the misfed paper following the procedure below.
■ Misfeed in the inserter
move the inserter away from the
1 Gently
machine while pressing the button.
6 Remove the misfed paper.
the misfed paper from the main
2 Remove
unit.
a misfeed was not found in step 6,
7 Ifremove
the misfed paper from under the
Be careful not to tear the
misfed paper during
removal.
After
removing
the
misfed paper, perform
steps 1 and 3 on page 224 to reset the machine.
paper is not found in step 2, open
3 Ifthemisfed
top cover.
4 Remove the misfed paper.
Be careful not to tear the
misfed paper during
removal.
Be careful not to tear the
misfed paper during
removal.
paper guide.
Be careful not to tear the
misfed paper during
removal.
the paper guide lever to its original
8 Return
position.
the finisher to close the gap between
9 Push
the machine and the inserter.
After
attaching
the
inserter on the machine,
make sure that the paper
misfeed message has
been cleared and the
normal message display
appears.
was not found in step 4, raise
5 Ifthea misfeed
paper guide lever.
3-17
3
dragonII_copy_sec.book
18 ページ
２００６年１０月１８日　水曜日　午後７時３９分
INSERTER
Troubleshooting inserter problems
Check the list below before calling for service.
Problem
Check
Solution or cause
The desired staple mode is not selected.
Select the desired staple mode at the
operation panel of the inserter (page 3-15).
The paper is not loaded in the correct
position.
Load the paper correctly (page 3-16).
The paper is not loaded face up.
Paper must be loaded face up in the inserter
tray (page 3-16).
Are any inserter covers open?
Close all covers.
"Disabling of inserter" is enabled in the
administrator settings.
Check the administrator settings and disable
"Disabling of inserter".
A paper misfeed message appears.
Remove the misfed paper (page 3-17).
The [START] key light is not illuminated.
Make sure that the punch or staple key has
been selected on the operation panel of the
inserter (page 3-15).
The paper is curled or damp.
Do not use curled or folded paper. When the
inserter is not going to be used for a long time,
remove the paper from the inserter, place it in
a bag so that it does not absorb moisture, and
store it in a cool and dark place.
A paper misfeed
occurs when paper
is fed from the
inserter.
Do the size and orientation of the loaded
paper match the paper size and orientation
set in "Setting the paper type and paper
size"?
Make sure paper size and orientation set in
"Setting the paper type and paper size" match
the size and orientation of the loaded paper.
A message appears
each time paper is
placed in the paper
tray of the inserter.
Was the [SIZE SELECT] key touched and
the size and orientation of the paper for the
inserter set as explained in "Setting the
paper type and paper size"?
To ensure that the correct paper (size and
orientation) is loaded in the inserter, the
machine indicates the current paper size
setting each time paper is placed in the paper
tray.
Stapling position is
not
correct
(including
saddle
stitch).
The inserter does
not operate.
Paper
occurs
3-18
misfeed
dragonII_copy_sec.book
19 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SHARP OSA
Sharp OSA (Open Systems Architecture) is an architecture that enables external applications to be directly
connected to a digital multifunction machine over a network.
When a digital multifunction machine that supports Sharp OSA is used, the operation panel controls and functions
of the machine such as scan send can be linked to an external application.
There are two types of external applications: "standard application" and "external account application". An "external
account application" is used for centralized account management of a multifunction machine on a network. A
"standard application" refers to all other applications.
APPLICATION
COMMUNICATION
MODULE (MX-AMX2)
The application communication module is required to use a "standard application" on the machine.
When a previously registered standard application is selected in the Web pages of the machine, the machine
retrieves the operation screen from the registered URL. Control of the operation screen is performed by the standard
application, and Scan to FTP can be executed.
Standard application setup
To register a standard application in the machine's Web pages, click [External Applications] in the administrator menu
frame and then click [Standard Applications]. Configure settings for the standard application in the screen that
appears.
Selecting a standard application
There are two methods for selecting a standard application that has been registered in the machine's Web pages.
■ Selecting a standard application from the job status screen
The Sharp OSA icon will appear in the lower left-hand corner of the job status screen. Follow the steps below to
select a standard application.
1 Touch the Sharp OSA icon.
If
no
standard
applications have been
stored in the Web pages,
the key cannot be
touched.
2 Select the standard application.
If two or more standard
applications have been
02
stored in the Web pages,
03
the screen to select the
standard application will
04
appear.
Touch
the
standard application that
you wish to use.
If only one standard application has been stored in
the Web pages, connection to the standard
application will begin.
App 01
App
App
App
machine
3 The
application.
connects to the standard
The message "Connecting to the external
application." appears while the machine
communicates with the standard application.
3-19
3
dragon_03.fm
20 ページ
２００６年１１月２９日　水曜日　午後８時４９分
APPLICATION COMMUNICATION MODULE (MX-AMX2)
■ Selecting the standard application from document filing mode
The [Sharp OSA] key appears in the upper right-hand corner of the document filing screen. Follow the steps
below to select a standard application.
1 Touch the [Sharp OSA] key.
SharpOSA
FILE RETRIEVE
FILE
FOLDER
If
no
standard
applications have been
stored in the Web pages,
the key cannot be
touched.
QUICK FILE
FOLDER
2 Select the standard application.
If one or more standard
applications have been
02
stored in the Web pages,
03
the screen to select the
standard application will
04
appear.
Touch
the
standard application that
you wish to use.
If only one standard application has been stored in
the Web pages, connection to the standard
application will begin.
App 01
App
App
App
machine
3 The
application.
connects to the standard
The message "Connecting to the external
application." appears while the machine
communicates with the standard application.
Operation in OSA mode
When the application communication module is installed, it is possible to check the job log of OSA scan mode in the
job status screen. The procedure for displaying the job log is the same as for regular Scan to FTP.
To display the job log of OSA scan mode, touch the [SCAN] key once again while the job log of scan mode appears
in the job status screen. (When this is done, the name of the key will change to [OSA SCAN].) To return to the scan
screen from the OSA scan screen, touch the [OSA SCAN] key.
3-20
dragon_03.fm
21 ページ
２００６年１０月２３日　月曜日　午後１２時０分
EXTERNAL ACCOUNT MODULE (MX-AMX3)
The external account module is required to use a "external account application" on the machine.
An external account application can be used in "external authentication mode" or "external count mode". When
external authentication mode is used, the login screen is retrieved from the application when the machine is started.
When a job ends, a job notification screen is sent to the application to enable counts to be kept for each authenticated
user.
When "external count mode" is used, the login screen is not displayed when the machine is started. Only a job result
notification is sent to the application. User authentication by the external account application cannot be used,
however, the external account application can be used in combination with the internal account function.
External account application setup
To register an external account application in the machine's Web pages, click [External Applications] in the
administrator menu frame and then click [External Accounting]. Configure settings for the external account
application in the screen that appears. To make the settings in the Web page take effect, restart the machine.
Operation in external account mode
3
The two modes for using an external account application operate as explained below.
■ External authentication mode
When the [ENABLE AUTHENTICATION BY EXTERNAL SERVER] checkbox is selected in "External account
setting" of "Sharp OSA settings" in the administrator settings, the machine enters external authentication mode.
When the machine is powered on in external authentication mode, the machine accesses the external account
application and displays the login screen. The login screen also appears when the [CALL] key is touched to run
a job in the job status complete screen. (The login screen does not appear if the user has already logged in by
the normal method.)
The [JOB STATUS] key can be pressed while the login screen appears to show the job status screen. To return
to the previous state, press the mode select key.
NOTES
● The user control function of the machine cannot be used in external authentication mode.
● The [SYSTEM SETTINGS] key can be pressed while the login screen appears to show the system settings
screen. To return to the initial state, touch the [EXIT] key.
If login fails
If the login screen fails to appear or the application does not operate correctly, the machine may also stop operating
correctly. In this event, it is recommended that you quit external account mode from the Web pages of the machine.
For more information, see [Help] in the Web pages.
If it is necessary to forcibly terminate external account mode using the operation panel of the machine, follow the
steps below.
Press the [SYSTEM SETTINGS] key and change "External account setting" in the administrator settings (see page
14 of the administrator settings guide). After changing the setting, restart the machine.
■ External count mode
When only the [ENABLE EXTERNAL ACCOUNT CONTROL] setting is enabled in "External account setting" of
"Sharp OSA settings" in the administrator settings, the machine enters external count mode.
Unlike external authentication mode, when the machine is started in "external count mode", the login screen of
the external account application is not displayed. Only the job result is sent to the external account application.
External count mode can be used together with the user control function of the machine. (External count mode
can also be used when the user control function is disabled.)
3-21
dragon_03.fm
22 ページ
２００６年１０月１９日　木曜日　午後１時１６分
dragonII_copy_sec.book
1 ページ
２００６年１０月１８日　水曜日　午後７時３９分
Part 2: Copier Operation
dragonII_copy_sec.book
2 ページ
２００６年１０月１８日　水曜日　午後７時３９分
dragonII_copy_sec.book
1 ページ
２００６年１０月１８日　水曜日　午後７時３９分
CHAPTER 4
MAKING COPIES
This chapter explains the basic procedures for making copies, including
selection of the copy ratio and other copy settings.
Page
AUTOMATIC DOCUMENT FEEDER ...................................................... 4-2
● Acceptable originals ........................................................................ 4-2
PLACING ORIGINALS............................................................................ 4-3
CHECKING THE SIZE OF A PLACED ORIGINAL ................................. 4-5
● Manually setting the scanning size ................................................. 4-5
STORING, DELETING, AND USING ORIGINAL SIZES ........................ 4-6
● Storing or deleting an original size.................................................. 4-6
NORMAL COPYING ............................................................................... 4-7
● Making copies with the automatic document feeding function ........ 4-7
● Automatic two-sided copying using the automatic document feeding
function............................................................................................ 4-10
● Copying from the document glass................................................... 4-11
● Automatic two-sided copying from the document glass .................. 4-13
ADJUSTING THE EXPOSURE .....................................................................4-14
REDUCTION/ENLARGEMENT/ZOOM................................................... 4-15
● Automatic selection (auto image).................................................... 4-15
● Manual selection (preset copy ratios/zoom).................................... 4-16
● XY ZOOM........................................................................................ 4-18
SPECIAL PAPERS.................................................................................. 4-20
4-1
dragonII_copy_sec.book
2 ページ
２００６年１０月１８日　水曜日　午後７時３９分
AUTOMATIC DOCUMENT FEEDER
The automatic document feeding function automatically feeds originals into the machine, making continuous copying
possible. In addition, both sides of two-sided sheet originals can be simultaneously scanned. This function is
convenient when you have a large number of original pages to scan.
Acceptable originals
Up to 150 originals (20 lbs. (80 g/m2)) of the same size, or an overall stack height of no more than 49/64" (19.5 mm),
can be loaded. Originals of mixed length can also be loaded together as long as they are the same width; however,
some special functions may not operate correctly.
■ Size and weight of acceptable
originals
■ Total number of originals that can be
set in the document feeder tray
●
Original size:
5-1/2" x 8-1/2"
or A5
(148 x 210 mm)
Maximum of 150 sheets (20 lbs. (80 g/m2)) or
total stack height of 49/64" (19.5 mm) or less.
11" x 17"
or A3
(297 x 420 mm)
Weight (thickness):
14 lbs. or 50g/m 2
42 lbs. or 128 g/m2
Special heavy papers
2
2
(65 lbs. (176 g/m ), 110 lbs. (205 g/m )) can be used.
2
g/m ... Weight of a sheet of paper of 1 m 2
■ Notes on use of the automatic document feeder
●Use originals within the specified size and weight ranges. Use of originals out of the specified range may cause
an original misfeed.
●Before loading originals into the document feeder tray, be sure to remove any staples or paper clips.
●If originals have damp spots from correction fluid, ink or glue from pasteups, be sure they are dried before they
are fed. If not, the interior of the document feeder or the document glass may be soiled.
●Do not use the following originals. These originals may cause incorrect original size detection, original
misfeeds, and smudges on copies.
● Transparency film, tracing paper, carbon paper, thermal paper or originals printed with thermal transfer ink
ribbon should not be fed through the document feeder. Originals to be fed through the feeder should not be
damaged, crumpled or folded or have loosely pasted paper on them or cutouts in them. Originals with multiple
punched holes other than two-hole or three-hole punched paper may not feed correctly.
●When using originals with two or three holes, place them so that the
Hole positions
punched edge is at a position other than the feed slot.
Hole
positions
Hole positions
4-2
dragon_04.fm
3 ページ
２００６年１１月２９日　水曜日　午後８時５１分
PLACING ORIGINALS
■ Using the
feeder
automatic
document
■ Using the document glass
the document cover, make sure that
1 Open
an original has not been left on the
Open the document cover, place the
original face down on the document glass,
and then gently close the document cover.
document glass, and then gently close the
document cover.
NOTES
● After placing the original, be sure to close the
document cover. If left open, parts outside of the
original will be copied black, causing excessive
use of toner.
● Do not place any objects under the original size
detector, because they may damage it or the
original size may not be detected properly.
the original guides to the size of the
2 Adjust
originals.
3
Document glass scale
mark
Place the originals face up in the
document feeder tray.
Document glass scale
mark
Place the originals face
up.
Insert the originals all
the
way
into
the
document feeder. The
stack height must not be
higher than the indicator
line (maximum of 150 pages).
8½x11 or A4
8½x14
or B4
11x17 or A3
8½x11
or A4
●Align the corner of the original with the tip of the
arrow mark
on the document glass scale.
●Place the original in the appropriate position for its
size as shown above.
NOTE
Original size detection function
One of the four groups of standard original sizes shown below can be selected for detection by the original size
detection function. The factory default setting is "INCH-1". The setting can be changed using "ORIGINAL SIZE
DETECTOR SETTING" in the administrator settings.
Detectable original sizes
Group
Document feeder tray (for reversing automatic document feeding)
Document glass
1
INCH-1
11" x 17", 8-1/2" x 14", 8-1/2" x 11",
8-1/2" x 11"R, 5-1/2" x 8-1/2"
Document glass + A4
2
INCH-2
11" x 17", 8-1/2" x 13", 8-1/2" x 11",
8-1/2" x 11"R, 5-1/2" x 8-1/2"
Document glass + A4
3
AB-1
A3, A4, A4R, A5,B4, B5, B5R
Document glass + 8-1/2" x 11", 216x330
4
AB-2
A3, A4, A4R, A5,B5, B5R, 216x330
Document glass + 8-1/2" x 11", B4
4-3
4
dragon_04.fm
4 ページ
２００６年１０月１９日　木曜日　午後１２時５８分
PLACING ORIGINALS
■ Standard original placement orientations
[Example 1]
Document feeder tray
Document glass
[Example 2]
Document feeder tray
Document glass
Place
originals
in
the
document feeder tray or on
the document glass so that
the top and bottom of the
original is positioned as
shown in the illustration. If not,
staples will be incorrectly
positioned and some special
features may not give the
expected result.
■ Automatic copy image rotation - rotation copying
If the orientation of the originals and copy paper are different, the original image will be automatically rotated 90°
and copied. (When an image is rotated, a message will be displayed.) If a function is selected that is not suitable
for rotation, such as enlarging the copy to greater than 8-1/2" x 11" (A4) size or staple sorting with the saddle
stitch finisher, rotation will not be possible.
[Example]
Orientation of original
Orientation of paper
Copy after rotation
Face down
Face down
●This function operates in both the auto paper select or auto image mode. ("Rotation copy setting" can be
disabled in the administrator settings. See page 16 of the administrator settings guide.)
4-4
dragonII_copy_sec.book
5 ページ
２００６年１０月１８日　水曜日　午後７時３９分
CHECKING THE SIZE OF A PLACED
ORIGINAL
If the placed original is a standard size, the size will be automatically
detected (automatic original detection function) and displayed in the touch
panel. Make sure that the correct size has been detected.
(A) : The original size is displayed.
(B) : [AUTO] appears when the automatic original detection function is
operating.
If you have loaded a non-standard size original or wish to change the
scanning size, you can follow the steps below to manually set the original
scanning size. (For the standard sizes, see "Original size detection
function" on page 4-3.)
0
81/2x11
AUTO
ORIGINAL
AUTO
EXPOSURE
(A)
(B)
NOTE
If a non-standard size original is loaded (including special sizes), the closest standard size may be displayed,
or the original size may not appear at all.
If "CANCEL DETECTION AT DOCUMENT GLASS" is enabled in the administrator settings (see page 11 of the
administrator settings guide), automatic original detection at the document glass will not operate. In this case,
follow the steps below to manually set the original scanning size.
Manually setting the scanning size
If you load an original that is not a standard size (such as an AB size), or if the size is not detected correctly, you must
touch the [ORIGINAL] key and set the original size manually. Perform the following steps after placing the document
in the automatic document feeder or on the document glass.
If a non-standard size original is placed in
the document feeder or on the document
glass, touch the [SIZE INPUT] tab and then
enter the X (width) and Y (length)
dimensions of the original.
Touch the [ORIGINAL] key.
1
0
AUTO
ORIGINAL
X is initially selected.
Enter the X dimension
1/2 17)
(width) and then touch
X
17 (2
inch
the Y( ) key and enter
(2 1/2 11 5/8)
Y
11 5/8 inch
the Y dimension (length).
STANDARD SIZE
SIZE INPUT
X can be from 2-1/2 to 17
inch, and Y can be from
2-1/2 to 11-5/8 inch.
If you frequently use originals that are the same
non-standard size, you can store the size as
explained in "STORING, DELETING, AND USING
ORIGINAL SIZES"on the following page. This will
save you the trouble of manually entering the size
each time you use that original size.
X
OK
Y
AUTO
EXPOSURE
2 Touch the desired original size key.
81/2 X13
51/2X81/2R
81/2 X14
AB
11X17
INCH
1/
2
8 X11
[AUTO] is no longer
highlighted. [MANUAL]
and the original size key
you
touched
are
highlighted.
OK
51/2X81/2
81/2X11R
STANDARD SIZE
SIZE INPUT
If you wish to select an AB size, touch the
[AB/INCH] key and then touch the desired
original size key.
A5
A4
OK
A5R
A4R
AB
B5
B4
INCH
B5R
A3
STANDARD SIZE
SIZE INPUT
[AB] is highlighted and
AB size keys are
displayed. To return to
the inch palette, touch
the [AB/INCH] key once
again.
3 Touch the [OK] key.
You will return to the initial screen.
selected original size appears in the
4 The
top half of the [ORIGINAL] key.
0
A4
ORIGINAL
AUTO
EXPOSURE
4-5
4
dragonII_copy_sec.book
6 ページ
２００６年１０月１８日　水曜日　午後７時３９分
STORING, DELETING, AND USING
ORIGINAL SIZES
Up to 9 special original sizes can be stored. Stored sizes can be easily called up and are not erased if the power is
turned off. Storing a frequently used original size saves you the trouble of manually setting the size each time you
copy that size of document.
● To cancel an original size storing, using, or deleting operation, touch the [ORIGINAL] key on the screen.
Storing or deleting an original size
1 Touch the [ORIGINAL] key.
the X (width) and Y (length)
5 Enter
dimensions of the original with the
0
keys.
AUTO
ORIGINAL
X
INCH
MANUAL
AUTO
EXPOSURE
COPY RAT
(2 1/2 17)
inch
you touch a key that shows an
7 When
original size in step 4, a message screen
appears that contains the keys [CANCEL],
[DELETE], and [STORE].
●To cancel the procedure, touch the [CANCEL]
key.
●To delete the selected original size, touch the
[DELETE] key.
●To change the original size stored in the key,
touch the [STORE] key. The screen of step 5
will appear to let you change the size.
AUTO
MANUA
CUSTO
SIZE
STORE/DELETE
the original size key (
4 Touch
you wish to store or delete.
) that
To store an original size,
touch a key that does not
show a size (
).
X51/2 Y101/8
RECALL
17
To exit, touch the [ORIGINAL] key.
3 Touch the [STORE/DELETE] key.
LL
STORE/DELETE
Keys that already have
an original size stored
will show the stored size
( X5 Y10 ).
1/
2
1/
8
To delete or change a stored size, touch the key
that shows the size that you wish to delete or
change.
●If you are storing an original size, go to step 5.
●To delete or change an original size, go to
step 7.
8 To exit, touch the [ORIGINAL] key.
■ USING A STORED ORIGINAL SIZE
steps 1 to 2 of "STORING
1 Follow
DELETING AN ORIGINAL SIZE".
OR
the original size key that you wish
2 Touch
to use.
X51/2 Y101/8
RECALL
STORE/DELETE
the [OK] key.
3 Touch
The stored original size is called up.
4-6
initially
key selected in step 4.
100%
E INPUT
is
the [OK] key.
6 Touch
The original size entered in step 5 is stored in the
AUTO 81/2x1
PAPER SE
CUSTOM
SIZE
X (width)
selected.
(2 1/2 11 5/8)
11 5/8 inch
2 Touch the [CUSTOM SIZE] key.
AUTO
OK
Enter X and then touch
the ( ) key to enter Y.
Y
A width of 2-1/2 to 17
inches can be entered in
RECALL
STORE/DELETE
X, and a length of 2-1/2
to 11-5/8 inches can be entered in Y.
X
AUTO
EXPOSURE
AB
CANCEL
Y
A
dragonII_copy_sec.book
7 ページ
２００６年１０月１８日　水曜日　午後７時３９分
NORMAL COPYING
This section describes the normal copying procedure.
Making copies with the automatic document feeding
function
■ 1-sided copies of 1-sided originals
Original
Copy
the originals in the document feeder
1 Place
tray. (pages 4-3 to 4-6)
5 Touch the [OK] key.
0
OK
4
2
Ensure that the 1-sided to 1-sided copy
mode is selected.
that paper of the same size as the
6 Ensure
originals is automatically selected*.
AUTO
EXPOSURE
The one-sided to onesided mode is selected
12
123 3
when no icon for a two8 x11
sided mode appears in
1.
2.
5. 8 x11
the dashed area on the
8 x11 8 x11
3. 8B4
x14
4. 11x17
display. If the 1-sided to
1-sided copy mode is
already selected, steps 3 to 5 are not needed.
ORIGINAL
8 x11
1/
2
AUTO 81/2x11
PAPER SELECT
1/
2
1/
2
1/
2
100%
O
1/
2
1/
2
The selected tray will be
highlighted
or
the
message "LOAD xxxxxx
PAPER." will appear. If
the message appears,
load paper in a paper
tray with paper of the
required size.
Even if the message above appears, copying can
be performed onto the currently selected paper.
3 Touch the [2-SIDED COPY] key.
*The following requirements must be satisfied.
Originals of a standard size (11" x 17", 8-1/2" x
14", 8-1/2" x 11", 8-1/2" x 11"R or 5-1/2" x 8-1/2R"
(A3, B4, A4, A4R, B5, B5R or A5)) are set and the
auto paper select function is enabled.
SPECIAL MODES
2-SIDED COPY
If originals of a size other
than the sizes above are
1. 8 x11
2. 8 x11
8 x11
to be copied, manually
PLAIN
PLAIN
PLAIN
select the desired paper
5. 8 x11
PLAIN
3. 8 x14
size by touching the
PLAIN
4. 11x17
PLAIN
[PAPER SELECT] key
and then touching the
desired paper size selection key.
READY TO SCAN FOR COPY.
OUTPUT
1/
2
4
Touch the [1-sided to 1-sided copy] key.
Touch the [1-sided to 1sided copy] key.
1/
2
1/
2
1/
2
1/
2
The selected key will be highlighted and the paper
selection screen will close. To close the paper
selection screen without making a selection, touch
the [PAPER SELECT] key.
4-7
dragonII_copy_sec.book
8 ページ
２００６年１０月１８日　水曜日　午後７時３９分
NORMAL COPYING
7 Select the desired output mode (page 4-9).
The sort mode is the
default mode.
To select the group
OUTPUT
mode,
touch
the
[OUTPUT] key, then
touch the [GROUP] key
FILE
on the output setting
screen, and then touch the [OK] key on the setting
screen.
2-SIDED COPY
the numeric keys to set the desired
8 Use
number of copies.
Up to 999 can be set.
If you are only making a
single copy, the copy can
be made with the copy
number display showing
"0". Use the [C] (clear)
LOGOUT
key to cancel an entry if
a mistake has been made.
4-8
9 Press the [START] key.
If the [C] key is pressed
while originals are being
scanned, scanning will
stop. If copying had
already started, copying
and scanning will stop
after the original in
progress is output to the original exit area. In these
cases the copy quantity will be reset to "0".
NOTES
● The 1-sided to 1-sided copying mode is set as the
default in the initial settings. If the default setting
has not been changed using the "Initial status
settings" (administrator settings), steps 3 to 5 on
page 4-7 can be omitted.
To cancel copying...
To cancel a copy job in progress, press the [CA]
key. A confirmation message will appear. Touch
the [YES] key to cancel copying.
dragonII_copy_sec.book
9 ページ
２００６年１０月１８日　水曜日　午後７時３９分
NORMAL COPYING
■ Copy output (sort and group)
Example: Making five sets or five copies each of three originals
● Sorting copies into sets
Original
Five sets of copies
OUTPUT
SORT
SPECIAL MODES
2-SIDED COPY
OUTPUT
GROUP
LOGOUT
Set the
number of
copies (5)
Touch the
[OUTPUT] key
Touch the
[SORT] key
Press the [START]
key
When using the automatic document feeding function,
sorting is automatically selected when the original is placed
in the document feeder.
● Grouping copies by page
4
Original
5 copies per page
OUTPUT
SORT
SPECIAL MODES
2-SIDED COPY
OUTPUT
GROUP
LOGOUT
Set the
number of
copies (5)
Touch the
[OUTPUT] key
Touch
the
[GROUP] key
Press the [START]
key
"Group" is automatically selected when the
original is placed on the document glass.
■ Selecting the output tray (when an optional finisher or saddle stitch finisher is
installed)
When the [FINISHER TRAY] key is highlighted, output pages are delivered to the finisher tray of the finisher or
saddle stitch finisher. When the "CENTER TRAY" key is highlighted, output pages are delivered to the center
tray. Touch the appropriate key to select the desired output tray.
0
OUTPUT
SORT
FINISHER
TRAY
STAPLE
SORT
GROUP
OK
CENTER
TRAY
SADDLE
STITCH
PUNCH
OFFSET
This screen appears when a saddle stitch finisher is installed.
The screen that appears when a finisher is installed is slightly different.
4-9
dragon_04.fm
10 ページ
２００６年１１月２９日　水曜日　午後８時５２分
NORMAL COPYING
Automatic two-sided copying
document feeding function
using
the
automatic
The machine can automatically copy two-sided originals, saving you the trouble of manually turning over each
original page.
Original
Copy
1. Automatic two-sided copying from one-sided
originals
2. Automatic two-sided copying from two-sided
originals
3. Automatic one-sided copying from two-sided
originals
the originals in the document feeder
1 Place
tray. (pages 4-3 to 4-6)
3 Select the desired copy mode.
The display will vary
depending
on
the
equipment installed.
ED COPY
2 Touch the [2-SIDED COPY] key.
SPECIAL MODES
If a copy key is touched for a mode that cannot
be selected, a double beep will sound.
Example of a
portrait-oriented
original
Example of a
landscape-oriented
original
2-SIDED COPY
OUTPUT
When making automatic two-sided copies of a
one-sided 11" x 17" (A3) or 8-1/2" x 14" (B4) size
portrait original, or when you wish to invert the top
and bottom of the back side of a two-sided original,
touch the [BINDING CHANGE] key.
4 Touch the [OK] key.
0
OK
BINDING
Perform steps 6 through 9 on pages 4-7 and 4-8.
4-10
dragonII_copy_sec.book
11 ページ
２００６年１０月１８日　水曜日　午後７時３９分
NORMAL COPYING
Copying from the document glass
When copying originals which cannot be fed from the automatic document feeder such as thick originals, open the
document cover and copy the originals from the document glass.
■ 1-sided copies of 1-sided originals
Original
Copy
the original on the document glass.
1 Place
(pages 4-3 to 4-6)
that paper of the same size as the
3 Ensure
original is automatically selected*.
AUTO
EXPOSURE
AUTO 81/2x11
PAPER SELECT
100%
COPY
RATIO
required size.
Document glass scale
mark
Even if the message above is displayed, copying
can be performed onto the currently selected
paper.
* The following requirements must be satisfied.
Originals of a standard size (11" x 17", 8-1/2" x 14",
8-1/2" x 11", 8-1/2" x 11"R or 5-1/2" x 8-1/2"R (A3,
B4, A4, A4R, B5, B5R or A5)) are set and the auto
paper select function is enabled.
Document glass scale
mark
8½x14
or B4
11x17 or A3
The selected tray will be
highlighted
or
the
message "LOAD xxxxxx
PAPER." will appear. If
the message appears,
load paper in a paper
tray with paper of the
8½x11
or A4
●Align the corner of the original with the tip of the
arrow mark
on the document glass scale.
●Place the original in the appropriate position for its
size as shown above.
If originals of a size other
than the sizes above are
1. 8 x11
2. 8 x11
8 x11
to be copied, manually
PLAIN
PLAIN
PLAIN
select the desired paper
5. 8 x11
PLAIN
3. 8 x14
size by touching the
PLAIN
4. 11x17
PLAIN
[PAPER SELECT] key
and then touching the
desired paper size selection key.
that the 1-sided to 1-sided copy
2 Ensure
mode is selected.
The selected key will be highlighted and the paper
selection screen will close. To close the paper
selection screen without making a selection, touch
the [PAPER SELECT] key.
8½x11 or A4
The one-sided to onesided mode is selected
22
when no icon for a two111 2
81/2x11
sided mode appears in
1.
2.
the dashed area on the
5.
8
x11
8 x11 8 x11
3. 8 B4
x14
display. If an icon
4. 11x17
appears, perform steps
3 to 5 on page 4-7 and then go to step 3.
ORIGINAL 81/2x11
1/2
1/2
READY TO SCAN FOR COPY.
1/
2
1/
2
1/
2
1/
2
1/
2
1/2
1/2
4-11
4
dragonII_copy_sec.book
12 ページ
２００６年１０月１８日　水曜日　午後７時３９分
NORMAL COPYING
the desired output mode. (page 44 Select
9.)
2-SIDED COPY
OUTPUT
FILE
Group mode
default mode.
is
6 Press the [START] key.
Replace the original with
the next original and
press the [START] key.
Repeat this operation
until all originals have
been scanned.
the
To select sort mode,
touch the [OUTPUT]
key, touch the [SORT]
key in the screen that
appears, and then touch
the [OK] key.
the numeric keys to set the desired
5 Use
number of copies.
Up to 999 can be set.
If you are only making a
single copy, the copy can
be made with the copy
number display showing
"0".
If you selected "Sort" for
the output mode in step 4 and pressed the
[START] key, it is necessary to touch the [READEND] key.
7 Touch the [READ-END] key.
PLACE NEXT ORIGINAL. PRESS [START].
WHEN FINISHED, PRESS [READ-END].
READ-END
LOGOUT
Use the [C] (clear) key to
cancel an entry if a mistake has been made.
To cancel copying...
To cancel a copy job in progress, press the [CA] key.
A confirmation message will appear. Touch the
[YES] key to cancel copying.
4-12
dragon_04.fm
13 ページ
２００６年１１月３０日　木曜日　午後４時１９分
NORMAL COPYING
Automatic two-sided copying from the document glass
The following two-sided copying function is possible. The copy paper is turned over automatically, allowing easy twosided copying.
Original
Copy
an original on the document glass.
1 Place
(pages 4-3 to 4-6)
3 Touch the [1-sided to 2-sided copy] key.
Example of a
portrait-oriented
original
Document glass scale
mark
8½x11 or A4
8½x14
or B4
11x17 or A3
Document glass scale
mark
8½x11
or A4
●Align the corner of the original with the tip of the
arrow mark
on the document glass scale.
●Place the original in the appropriate position for its
size as shown above.
2 Touch the [2-SIDED COPY] key.
SPECIAL MODES
2-SIDED COPY
OUTPUT
Example of a
landscape-oriented
original
When making automatic two-sided copies of a
one-sided 11" x 17" (A3) or 8-1/2" x 14" (B4) size
portrait original, or when you wish to invert the top
and bottom of the back side of a two-sided original,
touch the [BINDING CHANGE] key.
4 Touch the [OK] key.
0
OK
BINDING
Perform steps 3 to 7 on pages 4-11 and 4-12.
4-13
4
dragon_04.fm
14 ページ
２００６年１０月１９日　木曜日　午後１２時５８分
ADJUSTING THE EXPOSURE
Select an appropriate exposure mode for the original to be copied. The selections are AUTO, TEXT, TEXT/PHOTO
and PHOTO.
■ Automatic exposure adjustment
AUTO
The default exposure
ORIGINAL
setting is "AUTO", which
automatically
adjusts
the exposure for the
original. To select the
exposure mode, or to
1
AUTO 8 /2 x11
manually adjust the
PAPER SELECT
exposure level, follow the steps below.
AUTO
EXPOSURE
■ Selecting the exposure mode and manually adjusting the exposure level
1 Touch the [EXPOSURE] key.
3 Adjust the exposure level.
AUTO
ORIGINAL
AUTO
EXPOSURE
1
MANUAL
3
5
Touch the
key to
make darker copies.
Touch the
key to
make lighter copies.
AUTO 81/2x11
PAPER SELECT
2
Select [TEXT], [TEXT/PHOTO] or [PHOTO]
as appropriate for the original to be
copied.
0
TEXT
AUTO
ORIGINAL
OK
ORIGINAL
IMAGE TYPE
AUTO
MANUAL
NOTE
Exposure levels in TEXT mode
1 to 2: Dark originals such as newspaper
3:
Normal density originals
4 to 5: Originals written with pencils or light color
characters
EXPOSURE
TEXT/PHOTO
1
3
5
AUTO 81/2 x11
PAPER SELECT
PHOTO
To select [TEXT], touch the [AUTO
key so that [MANUAL] is selected.
100%
COPY RATIO
MANUAL]
Exposure modes selection
TEXT:
This mode is useful for producing
dark text copies with minimum
background.
TEXT/PHOTO: This provides the best balance for
copying an original which contains
both text and photos. This mode is
also useful for copying printed
photographs.
PHOTO:
This mode provides the best copies
of photographs with fine details.
4-14
About the steps that follow
If an automatic document feeder is being used,
see pages 4-7 through 4-10. If the document
glass is being used, see pages 4-11 through 413.
NOTES
● To return to the automatic exposure mode, touch
the [AUTO / MANUAL] key to highlight [AUTO],
and then touch the [OK] key.
● The exposure level used in automatic exposure
mode can be adjusted in the administrator
settings. See "Exposure adjustment" on page 16
of the administrator settings guide.
dragonII_copy_sec.book
15 ページ
２００６年１０月１８日　水曜日　午後７時３９分
REDUCTION/ENLARGEMENT/ZOOM
Reduction and enlargement ratios can be selected automatically or manually.
● Automatic selection: Auto image (see below)
● Manual selection: Preset copy ratios/zoom (see page 4-16)
Automatic selection (auto image)
The reduction or enlargement ratio will be selected automatically based on the original size and the selected paper size.
the original in the document feeder
1 Place
tray or on the document glass. (pages 4-3
3 Touch the [AUTO IMAGE] key.
5.81/2 x11
to 4-6)
The detected original size will be displayed.
NOTE
Automatic ratio adjustment can only be used for the
following original and paper sizes. It cannot be used
for other sizes. However, in the case of non-standard
original and paper sizes, the sizes can be entered to
make automatic ratio adjustment possible for those
sizes.
Original sizes:Standard sizes (see "Original size
detection function" on page 4-3.)
Paper size:
11" x 17", 8-1/2" x 14", 8-1/2" x 11", 81/2" x 11"R, or 5-1/2" x 8-1/2"R (A3,
B4, A4, A4R, B5, B5R, or A5R)
the [PAPER SELECT] key and then
2 Touch
select the desired paper size.
READY TO SCAN FOR COPY.
1. 81/2 x11
2. 81/2x11
PLAIN
PLAIN
3. 81/2x11
HEAVY PAPER
4. 11x17
PLAIN
81/2x11
PLAIN
The selected paper size
key is highlighted and
the paper selection
screen closes.
AUTO
IMAGE
The [AUTO IMAGE] key
will be highlighted and
the best reduction or
129%
enlargement ratio for the
COPY RATIO
original size and the
selected paper size will
be
selected
and
displayed in the copy ratio display.
PAPER SELECT
O
GE
NOTE
If the message "ROTATE ORIGINAL FROM
TO
" is displayed, change the orientation of the
original as indicated in the message. When the
message above is displayed, copying can be done
without changing the orientation, but the image will
not fit the paper correctly.
5. 81/2x11
PLAIN
NOTE
If paper of the desired size is not loaded in any tray,
load paper of the required size in a paper tray or the
bypass tray. (See "Setting the paper type and paper
size" on page 2-14.)
the numeric keys to set the desired
4 Use
number of copies.
Up to 999 can be set.
If you are only making a
single copy, the copy can
be made with the copy
number display showing
"0".
LOGOUT
Use the [C] (clear) key to
cancel an entry if a mistake has been made.
5 Press the [START] key.
If you placed the original
on the document glass,
set the output mode to
"Sort", and pressed the
[START] key, you must
touch the [READ-END]
key after all pages of the
original have been scanned. (Step 7 on page 4-12)
To cancel the auto image mode, touch the [CA] key.
4-15
4
dragon_04.fm
16 ページ
２００６年１０月１９日　木曜日　午後１２時５９分
REDUCTION/ENLARGEMENT/ZOOM
Manual selection (preset copy ratios/zoom)
Five preset enlargement and five preset reduction copy ratios (max. 400%, min. 25%) can be selected. In addition,
the zoom keys can be used to select any ratio from 25% to 400% in increments of 1%.
<The administrator settings on page 16 of the administrator settings guide can be used to set two additional
enlargement ratios and two additional reduction ratios.>
the original in the document feeder
1 Place
tray or on the document glass. (pages 4-3
the reduction, enlargement, and
4 Use
[ZOOM] keys on the touch panel to set the
to 4-6)
desired copy ratio.
NOTE
When the original is placed in the document feeder,
the ratio can be set from 25% to 200%.
ZOOM
2 Touch the [COPY RATIO] key.
XY ZOOM
AUTO 8 /2X11
PAPER SELECT
Zoom ratios: Any ratio
from 25% to 400% can
ZOOM
be set in 1% increments.
Touch the [
] key to
increase the ratio, or the
[
] key to decrease
MENU
XY ZOOM
the ratio. (If you continue
to touch the [
]/[
] key, the ratio will change
automatically. After 3 seconds, the ratio will
change rapidly.)
64
100%
COPY RATIO
the [MENU] key to select menu "
3 Use
menu " " for copy ratio selection.
" or
Menu
READY TO SCAN FOR COPY.
0
OK
ZOOM
NOTES
● Touch a reduction or enlargement key to set the
approximate ratio, then touch the [
] key to
increase the ratio or the [
] key to decrease the
ratio.
● Automatic changing of the ratio when a zoom key
is continuously touched can be disabled in the
administrator settings (see "Key operation setting
(prohibit key repeat)" on page 10 of the
administrator settings guide).
● If the message "IMAGE IS LARGER THAN COPY
PAPER." appears when a ratio is selected, the
image may not fit on the copy paper.
● To set the horizontal and vertical copy ratios
separately, use the XY ZOOM feature. See page
4-18.
AUTO
ORIGINAL
AUTO
EXPOSURE
AUTO 81/2x11
PAPER SELECT
XY ZOOM
MENU
AUTO
IMAGE
COPY RATIO
●A.Preset reduction copy ratios are:
77% and 64% (for the inch system).
70%, 81% and 86% (for the AB system).
●B.Preset enlargement copy ratios are:
121% and 129% (for the inch system).
115%, 122% and 141% (for the AB system).
Menu
0
OK
ZOOM
AUTO
ORIGINAL
AUTO
EXPOSURE
AUTO 81/2x11
PAPER SELECT
XY ZOOM
MENU
AUTO
IMAGE
5 Touch the [OK] key.
0
COPY RATIO
●A.Preset reduction copy ratios are:
50% and 25%.
●B.Preset enlargement copy ratios are:
200% and 400%.
(The custom ratios set by the administrator appear
in ratio menu 2.)
4-16
MENU
OK
AUTO
ORIGINAL
AUTO
EXPOSURE
AUTO 81/2x11
PAPER SELECT
IO
AUTO
IMAGE
COPY RATIO
dragonII_copy_sec.book
17 ページ
２００６年１０月１８日　水曜日　午後７時３９分
REDUCTION/ENLARGEMENT/ZOOM
sure that an appropriate paper size
6 Make
has been selected based on the selected
ratio.
ORIGINAL
81/2x11
4
5. 81/2x11
AUTO
EXPOSURE
Auto paper select display
AUTO 81/2x11
PAPER SELECT
64%
COPY RATIO
NOTE
If the auto paper select display does not appear, a
tray with the correct size of paper for the selected
ratio will not be automatically selected.
8 Press the [START] key.
If you placed the original
on the document glass,
set the output to "Sort",
and
pressed
the
[START] key, you must
touch the [READ-END]
key after all pages of the
original have been scanned. (Step 7 on page 4-12)
To return the ratio to 100%
To return the ratio setting to 100%, touch the [COPY
RATIO] key to display the ratio menu and then touch
the [100%] key. (Steps 2 and 3 on page 4-16.)
the numeric keys to set the desired
7 Use
number of copies.
Up to 999 can be set.
If you are only making a
single copy, the copy can
be made with the copy
number display showing
"0".
4
LOGOUT
Use the [C] (clear) key to
cancel an entry if a mistake has been made.
4-17
dragon_04.fm
18 ページ
２００６年１０月１８日　水曜日　午後８時５５分
REDUCTION/ENLARGEMENT/ZOOM
XY ZOOM
The XY ZOOM feature allows the horizontal and vertical copy ratios to be changed separately. The ratios can be set
from 25% to 400% in increments of 1%.
Example: Selecting 100% for the length and 50% for the width
Copy
Original
the original in the document feeder
1 Place
tray or on the document glass. (pages 4-3
to 4-6)
NOTE
When the original is placed in the document feeder,
the ratio can be set from 25% to 200%.
2 Touch the [COPY RATIO] key.
the
5 Use
ZOOM ([
reduction, enlargement, and
], [
]) keys to change the
copy ratio in the horizontal (X) direction.
Y
64%
10
ZOOM
50%
XY ZOOM
AUTO A4
PAPER SELECT
100%
COPY RATIO
A fixed ratio key will not
become
highlighted
when touched.
X
50
Y
100
Zoom ratios: Any ratio
from 25% to 400% can
be set in 1% increments.
Touch the [
] key to
increase the ratio, or the
[
] key to decrease
the ratio. (If you continue
to touch the [
]/[
] key, the ratio will change
automatically. After 3 seconds, the ratio will
change rapidly.)
ZOOM
3 Touch the [XY ZOOM] key.
MENU
XY ZOOM
4 Touch the [X] key.
X
100
Y
100
ZOOM
The initial state of the [X]
key
is
selected
(highlighted), so this
step normally is not
necessary. Touch the [X]
key only if it is not
highlighted yet.
NOTES
● Touch a reduction or enlargement key to set the
approximate ratio, then touch the [
] key to
increase the ratio or the [
] key to decrease the
ratio.
● Automatic changing of the ratio when a zoom key
is continuously touched can be disabled in the
administrator settings (see "Key operation setting
(prohibit key repeat)" on page 10 of the
administrator settings guide).
6 Touch the [Y] key.
X
50
Y
100
ZOOM
4-18
dragonII_copy_sec.book
19 ページ
２００６年１０月１８日　水曜日　午後７時３９分
REDUCTION/ENLARGEMENT/ZOOM
the
7 Use
ZOOM ([
reduction, enlargement, and
], [
]) keys to change the
copy ratio in the vertical (Y) direction.
77%
X
50
70
Y
64%
any desired copy settings such as
10 Select
the exposure or number of copies, and
then press the [START] key.
A fixed ratio key will not
become
highlighted
when touched.
ZOOM
50%
50
77
Y
The zoom keys can be
used to change the ratio
from 25% to 400% in
increments of 1%.
If needed, you can touch
the [X] key once again to
readjust the X zoom.
ZOOM
XY ZOOM
CANCEL
To cancel an X or Y zoom setting...
Touch the [XY ZOOM] key or the [CANCEL] key in
the ratio selection screen (step 3 or 5 on page 4-18).
8 Touch the [OK] key.
OK
129%
4
200%
100%
A
PA
400%
touch the [PAPER SELECT] key
9 Ifandneeded,
select the paper size.
0
1/
2
8 x11
N
APER
PLAIN
AUTO
ORIGINAL
AUTO
EXPOSURE
5. 81/2x11
PAPER SELECT
N
PLAIN
X-50% Y-70%
COPY RATIO
If the AUTO PAPER
SELECT mode is on, the
appropriate copy paper
size will have been
automatically selected
based on the original
size and selected copy
ratios.
4-19
dragonII_copy_sec.book
20 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL PAPERS
Special papers including transparency film, postcards and tabbed paper must be fed through the bypass tray.
the original in the document feeder
1 Place
tray or on the document glass. (pages 4-3
5 Select the bypass tray.
0
to 4-6)
81/2 x11
N
HEAVY PAPER
PAPER
5. 81/2 x11
AUTO
ORIGINAL
AUTO
EXPOSURE
PAPER SELECT
N
2 Load the special paper in the bypass tray.
See page 2-12 for the
specifications of paper
that can be used in the
bypass tray.
For the paper loading
instructions,
see
"Loading paper in the
bypass tray" (page 210).
[PAPER SELECT] key.
3 Touch theAUTO
EXPOSURE
4
AUTO 81/2x11
PAPER SELECT
100%
COPY
the type and size of paper loaded in the
4 Set
bypass tray.
0
8 x11
N
1
The (X) key shows the
currently
selected
paper type.
2
The (Y) key shows the
size of paper loaded
in the bypass tray.
AUTO
ORIGINAL
1/
2
AUTO
EXPOSURE
HEAVY PAPER
5. 81/2 x11
APER
PAPER SELECT
PLAIN
N
(X)
3
100%
COPY RATIO
(Y)
To change the displayed paper type, touch the
(X) key before touching the (Y) key. When
loading paper, if you changed the paper size
from an inch size to an AB size (or from an AB
size to an inch size), or if you changed the paper
type, be sure to change the paper type and size
settings as explained in steps 5 to 7 on page 214, and steps 8 to 10 on page 2-15.
4-20
PLAIN
100%
COPY RATIO
any desired copy settings such as
6 Select
the exposure or number of copies, and
then press the [START] key.
When copying from the
document glass in the
sort mode using the
[START] key, touch the
[READ-END] key after
all originals have been
scanned (step 7 on page
4-12).
dragonII_copy_sec.book
1 ページ
２００６年１０月１８日　水曜日　午後７時３９分
CHAPTER 5
CONVENIENT COPY
FUNCTIONS
This chapter explains special-purpose functions, storing of copy
settings, and other convenient functions. Please select and read
sections of this chapter as needed.
Page
SPECIAL MODES................................................................................... 5-2
● General procedure for using special functions ................................ 5-2
● Margin shift...................................................................................... 5-3
● Erase............................................................................................... 5-4
● Dual page copy ............................................................................... 5-5
● Pamphlet copy................................................................................. 5-6
● Job build.......................................................................................... 5-8
● Tandem copy ................................................................................... 5-10
● Covers/inserts ................................................................................. 5-12
● Transparency film with insert sheets ............................................... 5-23
● Multi shot......................................................................................... 5-24
● Book copy ....................................................................................... 5-26
● Tab copy .......................................................................................... 5-27
● Card shot......................................................................................... 5-29
● Mirror image .................................................................................... 5-31
● B/W reverse..................................................................................... 5-31
● Print menu....................................................................................... 5-32
STORING, USING AND DELETING JOB PROGRAMS ......................... 5-44
● Storing a job program...................................................................... 5-44
● Calling up a job program ................................................................. 5-45
● Deleting a stored job program......................................................... 5-45
INTERRUPTING A COPY RUN .............................................................. 5-46
5-1
dragonII_copy_sec.book
2 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
Touch the [SPECIAL MODES] key in the main screen of copy mode to open the special modes screen. The following
functions can be selected in the special modes screen.
Touch the [SPECIAL MODES]
key in the main screen.
READY TO SCAN FOR COPY.
0
SPECIAL MODES
ORIGINAL 81/2 x11
2-SIDED COPY
81/2 x11
OUTPUT
1.
FILE
2.
81/2 x11 81/2 x11
3. 81/2 x14
4. 11x17
QUICK FILE
1
Margin shift (page 5-3)
2
Erase (page 5-4)
3
Dual page copy (page 5-5)
4
Pamphlet copy (page 5-6)
5
Job build (page 5-8)
6
Tandem copy (page 5-10)
81/2 x11
OK
SPECIAL MODES
AUTO
ORIGINAL
AUTO
EXPOSURE
MARGIN SHIFT
AUTO 81/2x11
PAPER SELECT
PAMPHLET COPY
ERASE
JOB
BUILD
DUAL PAGE
COPY
1/3
TANDEM
COPY
100%
COPY RATIO
7
[OK] key on the special modes screen
Touch the [OK] key to return to the main screen of
copy mode.
8
/
key
Touch these keys to change the special modes
screen.
There are three special modes screens.
Touch the
key to change to the other two screens.
●The following special functions can be selected in the 2nd screen (2/3).
Covers/inserts (page 5-12)
Book copy (page 5-26)
Transparency inserts (page 5-23)
Tab copy (page 5-27)
Multi shot (page 5-24)
Card shot (page 5-29)
●The following special functions can be selected in the 3rd screen (3/3).
Mirror image (page 5-31)
B/W reverse (page 5-31)
Print menu (page 5-32)
General procedure for using special functions
1 Touch the [SPECIAL MODES] key.
To select a special function in one of the other two
screens, use the
/
keys to change the
screen.
SPECIAL MODES
2-SIDED COPY
OUTPUT
2 Touch
mode.
the key for the desired special
SPECIAL MODES
MARGIN SHIFT
PAMPHLET COPY
5-2
ERASE
JOB
BUILD
Example:
Selecting the
shift function
margin
Setting procedures for modes requiring setting
screens start on the next page.
The dual page copy, job build, tandem copy,
mirror image and B/W reverse functions do not
require setting screens.
dragon_05.fm
3 ページ
２００６年１０月１９日　木曜日　午後１時０分
SPECIAL MODES
Margin shift
The margin shift function will automatically shift the text or image on the copy paper approximately 1/2" (10 mm) in
its initial setting.
This function is convenient when stapling or binding copies with a string.
NOTE
The initial setting for the margin width can be changed in the administrator settings to any value from 0" to 1" (0
to 20 mm) (page 16 of the administrator settings guide).
One-sided copying
Image shifted
Original
to the right
Image shifted
to the left
●The shift direction can be selected from right or left
shift as shown in the illustration.
Margin
Margin
Two-sided copying
Original
Image shifted
to the right
Image shifted
to the left
5
Or
Margin
Margin
To display the special modes screen...
See "General procedure for using special
functions" on page 5-2.
the shift amount as needed and touch
3 Set
the [OK] key.
OK
CANCEL
1
Touch the [MARGIN SHIFT] key on the
special modes screen.
SPECIAL MODES
MARGIN SHIFT
PAMPHLET COPY
ERASE
JOB
BUILD
The margin shift setting
screen will appear.
The margin shift icon
( ) will also appear in
the upper left of the
screen to indicate that
the function is turned on.
2 Select the shift direction.
RIGHT
LEFT
Touch a shift direction
key to select right or left.
The selected key will be
highlighted.
SIDE 1
1/2
(0 1)
inch
OK
SIDE 2
1/2
(0 1)
inch
Use the
and the
keys to set the shift
amount.
The
shift
amount can be set from
0" to 1" in 1/8" (0 to 20
mm
in
1
mm)
increments.
the [OK] key on the special modes
4 Touch
screen.
You will return to the main screen of copy mode.
About the steps that follow
If an automatic document feeder is being used,
see pages 4-7 through 4-10. If the document
glass is being used, see pages 4-11 through 413.
To cancel the margin shift function, touch the
[CANCEL] key on the margin shift setting screen
(step 3).
5-3
dragon_05.fm
4 ページ
２００６年１０月１９日　木曜日　午後１時０分
SPECIAL MODES
Erase
The erase function is used to erase the shadow lines on copies produced when copying thick originals or books. The
erase modes that can be selected are shown below. The erase width is approximately 1/2" (10 mm) in it's initial
setting.
NOTE
The initial setting for the erasure width can be changed in the administrator settings to any value from 0" to 1" (0
to 20 mm) (page 16 of the administrator settings guide).
Original
Copy
EDGE ERASE
Eliminates shadow lines around the edges of
copies caused when heavy paper or a book is used
as an original.
CENTER ERASE
Eliminates shadow lines produced by the bindings
of bound documents.
EDGE + CENTER ERASE
Eliminates shadow lines around the edges of copies
and eliminates the shadow at the center of copies.
To display the special modes screen...
See "General procedure for using special
functions" on page 5-2.
the amount of erase and touch the
3 Adjust
[OK] key.
CANCEL
OK
EDGE
1
Touch the [ERASE] key on the special
modes screen.
MODES
RGIN SHIFT
PHLET COPY
ERASE
DUAL
C
JOB
BUILD
TAN
C
The erase setting screen
will appear.
The erase icon ( ) will
also appear in the upper
left of the screen to
indicate that the function
is turned on.
2 Select the desired erase mode.
ERASE
EDGE
ERASE
CENTER
ERASE
EDGE+CENTER
ERASE
Select one of the three
erase
modes.
The
selected key will be
highlighted.
1/2
(0 1)
inch
Use the
and
keys
to set the erase width to
any value from 0" to 1" in
increments of 1/8" (0 to
10 mm in 1 mm).
the [OK] key on the special modes
4 Touch
screen.
You will return to the main screen of copy mode.
About the steps that follow
If an automatic document feeder is being used,
see pages 4-7 through 4-10. If the document
glass is being used, see pages 4-11 through 413.
NOTE
When erase is used, edge erase takes place at the
edges of the original image. If you also use a ratio
setting, the edge erase width will change according
to the set ratio.
To cancel the erase function, touch the [CANCEL]
key on the erase setting screen (step 3).
5-4
dragonII_copy_sec.book
5 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
Dual page copy
The dual page copy function produces separate copies of two documents placed side by side on the document glass.
This function is especially useful when copying books and other bound documents.
[Example] Copying right and left pages of a book
Book original
Dual page copy
●The dual page copy function can be used only
when copying from the document glass. The
automatic document feeder cannot be used with
this function.
●Only 8-1/2" x 11" (A4) paper can be used.
To display the special modes screen...
See "General procedure for using special
functions" on page 5-2.
that 8-1/2" x 11" (A4) size paper is
4 Ensure
selected.
AUTO 8 x11
PAPER SELECT
1/2
the [DUAL PAGE COPY] key on the
1 Touch
special modes screen.
OK
1/3
RASE
DUAL PAGE
COPY
JOB
BUILD
TANDEM
COPY
The
[DUAL
PAGE
COPY] key will be
highlighted to indicate
that the function is
turned on, and the dual
page copy icon (
) will
appear in the upper left
of the screen.
the [OK] key on the special modes
2 Touch
screen.
100%
If 8-1/2" x 11" (A4) size
paper is not selected,
touch
the
[PAPER
SELECT] key to select
8-1/2" x 11" (A4) size
paper.
About the steps that follow
For two-sided copying, follow steps 2 through 4
on page 4-13 and then follow steps 4 through 6
on page 4-12.
For one-sided copying, follow steps 4 through 6
on page 4-12.
You will return to the main screen of copy mode.
3 Place the originals on the document glass.
When copying a thick
book, press down lightly
on the book to flatten it
against the document
glass.
Index 81/2" x 11"
NOTE
To erase shadows caused by document binding, use
the edge erase function (page 5-4). (Center Erase
and Edge + Center Erase cannot be used in
combination.)
To cancel the dual page copy function, touch the
[DUAL PAGE COPY] key on the special modes
screen (screen of step 1).
A4
This page
is copied
first.
Center line of
original
81/2" x 11"
(A4)
11" x 17"
(A3)
Place the opened original on the document glass so
that the first page you wish to copy is on the right and
the center of the original is aligned with the size mark.
5-5
5
dragonII_copy_sec.book
6 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
Pamphlet copy
The pamphlet copy function is used to arrange copies in proper order for eventual center-stapling and folding into a
booklet. Two original pages are copied onto each side of copy paper. Four pages are, therefore, copied onto one sheet.
This function is convenient for arranging copies into an attractive booklet or pamphlet.
NOTE
To make pamphlet copies of a book or other bound original, use the book copy function (page 5-26). The book copy
function scans the opened original in two-page units. (Two pages are scanned at each scan, reducing the number
of repetitions of the scanning operation by a half.)
[Example] Copying eight originals in the pamphlet copy mode
Originals
(one-sided)
● Scan the originals from the first page to the last
page. The order of copying will be automatically
adjusted by the machine.
● Either left binding (right to left turning) or right
binding (left to right turning) can be selected.
● Four originals will be copied onto one sheet.
Blank pages may be automatically produced at
the end depending on the number of the originals.
● If a saddle stitch finisher is installed, copies can
be stapled in two positions along the center of
copies and folded at the center.
Finished copies are
folded in two.
Left binding
1
2
3
4
5
6
First page
7
8
Originals
(two-sided)
2
4
6
8
Right binding
1
3
First page
5
7
To display the special modes screen...
See "General procedure for using special
functions" on page 5-2.
the binding position (left binding or
3 Select
right binding).
LEFT
BINDING
RIGHT
BINDING
C
SE
the [PAMPHLET COPY] key on the
1 Touch
special modes screen.
SPECIAL MODES
MARGIN SHIFT
PAMPHLET COPY
ERASE
JOB
BUILD
The PAMPHLET COPY
setting
screen
will
appear. The pamphlet
copy icon ( , etc.) will
also appear in the upper
left corner of the screen
to indicate that the
function is turned on.
the type of originals
2 Designate
copied: 1-sided or 2-sided.
ORIGINAL
1-SIDED
2-SIDED
5-6
to be
Select the [2-SIDED] key
if you wish to scan a twosided original using the
automatic
document
feeding function.
If you wish to insert a different type of paper for use as
a cover, follow steps 4 through 12 below.
If you do not wish to insert paper for a cover, continue
from step 8 on the next page.
4 Touch the [COVER SETTING] key.
CANCEL
NG
OK
RIGHT
BINDING
COVER
SETTING
dragonII_copy_sec.book
7 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
whether or not you wish to copy on
5 Select
the cover ("YES" or "NO").
the original in the document feeder
9 Place
or on the document glass. (page 4-3)
PRINT ON COVER
YES
that the desired paper size has
10 Ensure
been automatically selected based on the
NO
original size.
6 Select the paper tray for the cover.
The currently selected
paper tray for the
cover is displayed.
2 The size and type of
paper in the currently
selected
tray
is
displayed.
1
CANCEL
OK
PAPER TRAY
BYPASS
TRAY
81/2x11
PLAIN
In the example screen above, 8-1/2" x 11" (A4)
size plain paper is loaded.
To change the paper tray for the cover, touch the
tray selection key. (In the screen example, the
"BYPASS TRAY" display is the tray selection key.)
The tray selection screen appears when the tray
selection key is touched. Select the desired tray in
this screen.
NOTES
● When the cover paper is fed from the inserter, the
cover cannot be copied on.
● Two-sided copying is not possible on label sheets,
transparency film, and tabbed paper. When
copying on a cover, do not select a tray that has
one of these types of paper.
7 Touch the [OK] key.
CANCEL
G
OK
RIGHT
BINDING
COVER
SETTING
8 Touch the [OK] key.
OK
CANCEL
LEFT
BINDING
OK
RIGHT
BINDING
Return to the main
screen of copy mode.
To select another size
paper, select the desired
AUTO 11x17
size and touch the
PAPER SELECT
[AUTO IMAGE] key. The
appropriate copy ratio
will
be
selected
100%
automatically based on
the original size and the paper size. (See steps 2
and 3 on page 4-15.)
any desired copy settings such as
11 Select
the exposure or number of copies, and
then press the [START] key.
using
12 [When
feeder:]
the automatic document
Copying will start after all originals have been
scanned. (The next step is not needed.)
[When using the document glass:]
Replace the original with the next original and
press the [START] key. Repeat this operation until
all originals have been scanned and then touch
the [READ-END] key.
NOTES
● When the pamphlet copy function is set, the twosided copying mode will be automatically selected.
● If this function is used in combination with the
pamphlet copy function (pamphlet stapling) and
the number of origial pages exceeds the number
of pages that can be stapled, a message asking
you to select "CANCEL", "CONTINUE", or
"DIVIDE" will appear.
To cancel the job, select "CANCEL". To make
pamphlet copies without stapling, select
"CONTINUE". To divide the pages into sets that
can be stapled, select "DIVIDE".
If you performed steps 4 to 6 to insert cover paper,
divided stapling is not possible. You can either
continue pamphlet copying without stapling, or
cancel the job.
To cancel the pamphlet copy function, touch the
[CANCEL] key on the pamphlet copy setting screen
(step 2).
COVER
SETTING
5-7
5
dragonII_copy_sec.book
8 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
Job build
Use job build mode when you need to copy more original pages than can be loaded at once in the document feeder
(the maximum number of pages that can be loaded is 150). This function allows the original pages to be scanned in
sets.
[Example] Copying 300 pages of 8-1/2" x 11" originals
Originals
1
1
A:150 sheets
300 original pages
151
B:150 sheets
*Divide the originals into sets of 150 pages each.
Scan the originals starting from the first page of set
A. Scan set B next, taking care to keep the correct
page order.
To display the special modes screen...
See "General procedure for using special
functions" on page 5-2.
sure that the desired paper size is
4 Make
selected, select the number of copies or
other copy settings, and
[START] key.
N SHIFT
LET COPY
DUAL
COP
ERASE
JOB
BUILD
TANDE
COPY
The [JOB BUILD] key
will be highlighted to
indicate that the function
is turned on, and the job
build icon (
) will
appear in the upper left
of the screen.
the [OK] key on the special modes
2 Touch
screen.
OK
Return to the main
screen of copy mode.
1/3
DUAL PAGE
COPY
RASE
5 Touch the [READ-END] key.
INTERRUPT
ES
TANDEM
COPY
JOB
BUILD
ORIGINAL
3
81/2x11
PLACE NEXT ORIGINAL. PRESS [START].
TO CHANGE COPY SETTINGS,
PRESS [CHANGE].
CHANGE
Place the first set of originals in the
document feeder tray. (page 4-3)
the
Scanning of originals will
start. After scanning of
the first set of originals (A
in the example above) is
completed, remove the
scanned originals, place
the next set of originals
(set B in the example) and press the [START] key.
Repeat this operation until all sets of originals have
been scanned.
If you wish to adjust the copy settings each time
you place a set of originals, see "Changing the
copy settings for each set of originals" on the next
page.
the [JOB BUILD] key on the special
1 Touch
modes screen.
ES
press
4.
READ-END
11x17
C
To cancel the job build function, touch the [JOB
BUILD] key on the special modes screen (step 1).
The highlighted display will be canceled.
5-8
dragonII_copy_sec.book
9 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
■ Changing the copy settings for each set of originals
When using job build mode, you can change the copy settings each time you place a set of originals.
After performing step 4 on page 5-8, follow the steps below.
5 Touch the [CHANGE] key.
7 Touch the [READ-END] key.
INTERRUPT
ES
ORIGINAL
INTERRUPT
ES
81/2 x11
PLACE NEXT ORIGINAL. PRESS [START].
TO CHANGE COPY SETTINGS,
PRESS [CHANGE].
CHANGE
4.
ORIGINAL
81/2x11
PLACE NEXT ORIGINAL. PRESS [START].
TO CHANGE COPY SETTINGS,
PRESS [CHANGE].
CHANGE
READ-END
4.
11x17
C
READ-END
11x17
C
the desired copy settings in the
6 Select
screen that appears and press the
[START] key.
INTERRUPT
[START].
ORIGINAL 81/2x11
81/2x11
1.
2.
81/2x11 81/2x11
3. 81/2x14
4. 11x17
5. 81/2x11
READ-END
AUTO
EXPOSURE
AUTO 81/2x11
PAPER SELECT
100%
COPY RATIO
The copy settings that
can be selected are
"EXPOSURE", "PAPER
SELECT", and "COPY
RATIO".
If you touch the [READEND] key now, copying
will
begin
without
scanning the new set of
originals.
5
NOTES
● If the original size was set manually at the beginning of the job build procedure, it will not be possible to change
the original size setting. If the automatic original detection function is operating, the original size will be detected
for each set of originals placed.
● When the bypass tray is selected, it is not possible to change the paper type.
● If "XY ZOOM" was initially set for the ratio, it will not be possible to change the ratio setting.
● When job build mode is used in combination with any of the following functions, the [CHANGE] key will not
appear in the screen of step 5.
Pamphlet copy, tandem copy, covers/inserts, transparency inserts, multi-shot, book copy, tab copy, staple sort,
saddle stitch
5-9
dragon_05.fm
10 ページ
２００６年１０月１９日　木曜日　午後１時０分
SPECIAL MODES
Tandem copy
Two machines connected to the same network can be used to run a large copy job in parallel.
By dividing the job in half, approximately half the time is required to complete the job.
To use this function, two machines must be connected to your network as network printers. Even if more machines
are connected to the network, this function can only be used to have one other machine share a job.
100 sets of
copies
50 sets of
copies
50 sets of
copies
To display the special modes screen...
See "General procedure for using special
functions" on page 5-2.
the [TANDEM COPY] key on the
1 Touch
special modes screen.
OK
1/3
ERASE
DUAL PAGE
COPY
JOB
BUILD
TANDEM
COPY
The [TANDEM COPY]
key will be highlighted to
indicate that the function
is turned on, and the
tandem copy icon (
)
will appear in the upper
left of the screen.
the [OK] key on the special modes
2 Touch
screen.
OK
RASE
JOB
BUILD
5-10
DUAL PAGE
COPY
TANDEM
COPY
1/3
You will return to the
main screen of copy
mode.
Server machine and client machine
●In the following explanations, the machine on which
the copy job is initially set up and tandem copy
selected is called the server machine. The other
machine that is asked to share the job is called the
client machine.
●To use the tandem copy function, the tandem
settings must be configured in the administrator
settings. (See page 13 of the "Administrator settings
guide")
●When configuring the tandem settings in the server
machine, the IP address of the client machine must
be entered. For the port number, it is best to use the
initial setting (50001). Unless you experience
difficulty with this setting, do not change it. The
tandem settings should be configured by your
network administrator. If the server and client
machines will alternate server and client roles, the IP
address of the server machine must also be entered
in the client machine.The same port number can be
set in both machines.
the number of copies with the numeric
3 Set
keys.
Up to 999 copies can be
set. When the [START]
key is pressed, the
copies will automatically
be divided between the
server
and
client
LOGOUT
machines. If an odd
number of copies is set, the server machine will
make the extra set.
If an incorrect number of copies is set...
Press the clear key and set the correct number of
copies.
the original in the document feeder
4 Place
or on the document glass. (page 4-3)
dragonII_copy_sec.book
11 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
5 Press the [START] key.
To cancel the tandem copy function, touch the
[TANDEM COPY] key on the special modes screen
(step 1). The highlighted display will be canceled.
NOTES
● To perform tandem copying, the server machine
and client machine must meet certain conditions.
After the [START] key is pressed on the server
machine, the server machine verifies that the
conditions have been met. If the conditions have
not been met, tandem copying does not begin
and "TANDEM OUTPUT IS NOT ALLOWED.
OUTPUT ALL SETS USING MASTER
MACHINE?" appears in the display. To have the
server machine make all the copies, touch the
[OK] key. To cancel the job, touch the [CANCEL]
key.
• As an example, the following conditions must
be met when a staple finisher is installed on the
server machine and not on the client machine:
(1) If tandem copying is executed for a twosided copy job with the number of copies
set to 999 and "Non-staple" is selected,
tandem copying will take place.
(2) If tandem copying is executed for a twosided copy job with the number of copies
set to 999 and "Staple" is selected,
tandem copying will not take place
because the client machine does not have
a finisher.
5
● After the [START] key is pressed, if the client
machine cannot print because it is out of paper or
other reason, the server machine will print its half
of the job. The other half of the job will be stored in
the client machine and the job will be printed when
the client machine is able to print.
● If auditing mode is enabled on both the server and
client machines, the same account number must
be entered on both machines.
● If auditing mode is enabled on the client machine
but not on the server machine, tandem copying
cannot be performed.
5-11
dragonII_copy_sec.book
12 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
Covers/inserts
A different type of paper can be inserted in positions corresponding to front and back covers of a copy job when the
automatic document feeding function is used. A different type of paper can also be automatically added as an insert
at specified pages.
As an example, tabbed paper can be added as inserts at the beginning of chapters or at other pages to create an
indexed document.
● Covers/inserts can be disabled in the administrator settings (page 11 of the administrator settings guide).
Example of adding covers
Example of adding inserts
Originals
Originals
Back cover
Front cover
Inserts
Example of adding covers and inserts
Originals
Back
cover
Front
cover
About the explanations of covers and
inserts
There are various ways of using covers and inserts.
To keep the explanations simple, covers and inserts
are explained separately. The procedure for
inserting covers is explained on page 5-13. The
procedure for adding inserts is explained on page 514. After reading these explanations, see the
examples of using covers and inserts on pages 517 to 5-22.
Inserts
■ Preparations for using covers and inserts
● Load the cover/insert paper in the tray before using the cover/insert function.
● Use the same size of paper for the covers/inserts as for the copies. (For the procedures for loading paper, see
pages 2-2 to 2-17.)
● Before selecting the cover/insert function, place the originals in the document feeder, select one-sided or twosided copying, and select the number of copies and any other desired copy settings as explained on pages 47 to 4-10. When these settings have been completed, perform the procedure to select covers/inserts on the
following page.
● The original must be scanned from the document feeder. The document glass cannot be used.
● Tabbed paper can be used for cover/ inserts, however, two-sided copying cannot be performed on the tabbed
paper. Tabbed paper can be fed from the bypass tray, tray 3, and the inserter. The other trays cannot be used.
● Up to 100 covers/inserts can be inserted. Two covers/inserts cannot be inserted between the same pages.
● Pamphlet copying cannot be used in combination with covers/inserts.
● When performing two-sided copying of two-sided originals, an insert cannot be added between the front and
back sides of an original page.
5-12
dragonII_copy_sec.book
13 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
■ Procedure for inserting front and back cover paper
The paper for the front cover is called the front cover paper ("FRONT COVER" in the touch panel). The paper
for the back cover is called the back cover paper ("BACK COVER" in the touch panel).
●Examples of insertion methods for the front and back cover paper are given on pages 5-18 to 5-21.
To display the special modes screen...
See "General procedure for using special
functions" on page 5-2.
the insertion conditions for the front
5 Set
cover paper.
PLEASE SET UP A FRONT COVER.
0
CANCEL
FRONT COVER SETTING
the [COVERS/INSERTS] key in the
1 Touch
special modes screen (2nd screen).
PRINT ON FRONT COVER
1-SIDED
YES
BYPASS
TRAY
2-SIDED
NO
81/2x11
PLAIN
SPECIAL MODES
COVERS/INSERTS
TRANSPARENCY
INSERTS
BOOK COPY
TAB COPY
2
2 Touch the [PAPER TRAY SETTINGS] key.
CANCEL
COVERS/INSERTS
FRONT COVER
INSERTION
TYPE A SETTING
BACK COVER
INSERTION
TYPE B SETTING
INSERTION
SETTINGS
OK
PAPER TRAY
SETTINGS
PAGE LAYOUT
3
Select the tray used for the front cover
paper.
OK
PAPER TRAY SETTINGS
FRONT COVER
BACK COVER
INSERTION
TYPE A
BYPASS
TRAY
BYPASS
TRAY
BYPASS
TRAY
BYPASS
TRAY
81/2x11
PLAIN
81/2x11
PLAIN
81/2x11
PLAIN
81/2x11
PLAIN
(X)
1
2
INSERTION
TYPE B
(Y)
(Z)
Select whether or not the front cover paper is to be
copied on with the (X) keys ([YES] or [NO]).
Select whether one-sided copying or two-sided
copying is to be performed on the front cover
paper with the (Y) keys. This selection is only
possible when the [YES] key of (X) has been
selected. (The one-sided/two-sided selection
made here only applies to the front cover paper.
When the back cover paper is selected, the
selection only applies to the back cover paper.)
The (Z) key shows the tray selected for the front
cover paper in step 3 and the paper size and
type.
the [OK] key in the screen of step 5.
6 Touch
You will return to the screen of step 2.
When you return to the screen of step 2, the
[FRONT COVER] key will be highlighted.
insert back cover paper, repeat steps 2
7 To
through 6, using the [BACK COVER] key
instead of the [FRONT COVER] key.
The tray name (tray position) selected for the
front cover paper and the paper size and type
are shown in (X). If the tray in which you
loaded paper for the front cover is shown, touch
the [OK] key. You will return to the screen of step
2.
If the correct tray for the cover sheet paper does
not appear in (X), touch the (Y) key. The tray
selection screen will appear. Select the tray in
which you loaded paper for the front cover. You
will return to the screen of above.
the [FRONT
4 Touch
screen of step 2.
(Y)
(X)
1
3
OK
PAPER TRAY
COVER] key in the
PLEASE SET UP COVERS/INSERTS.
0
OK
SPECIAL MODES
CANCEL
COVERS/INSERTS
FRONT COVER
INSERTION
TYPE A SETTINGS
BACK COVER
INSERTION
TYPE B SETTINGS
INSERTION
SETTINGS
OK
PAPER TRAY
SETTINGS
PAGE LAYOUT
the [PAGE LAYOUT] key in the
8 Touch
screen of step 7 to display a list of the
selected settings (page 5-16).
To edit or delete a cover/insert, follow
steps 1 and 2 on page 5-16. To exit the
cover/insert settings, touch the upper
[OK] key in the screen of step 7.
9 Press the [START] key.
To cancel covers/inserts settings...
Touch the [CANCEL] key in the screen of step 2.
5-13
5
dragonII_copy_sec.book
14 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
■ Procedure for adding inserts
You can have different paper automatically inserted as an insert at a specified pages. Two types of insert paper
can be used. These are specified with the [INSERTION TYPE A SETTING] key and [INSERTION TYPE B
SETTING] in the touch panel. Tabbed paper can be used as an insert.
●Examples of insertion methods for insert paper are given on page 5-22.
To display the special modes screen...
See "General procedure for using special
functions" on page 5-2.
the insertion conditions for insertion
5 Set
type A .
PRINT ON INSERT SHEETS
1
CANCEL
INSERTION TYPE A SETTING
Touch the [COVERS/INSERTS] key in the
special modes screen (2nd screen).
YES
1-SIDED
2-SIDED
OK
PAPER TRAY
BYPASS
TRAY
NO
81/2x11
PLAIN
TAB COPY
SPECIAL MODES
(X)
COVERS/INSERTS
TRANSPARENCY
INSERTS
BOOK COPY
TAB COPY
1
2
2 Touch the [PAPER TRAY SETTINGS] key.
CANCEL
COVERS/INSERTS
FRONT COVER
INSERTION
TYPE A SETTING
BACK COVER
INSERTION
TYPE B SETTING
INSERTION
SETTINGS
OK
PAPER TRAY
SETTINGS
3
PAGE LAYOUT
4
3
Select the tray used for insertion type A.
OK
PAPER TRAY SETTINGS
FRONT COVER
BACK COVER
INSERTION
TYPE A
INSERTION
TYPE B
BYPASS
TRAY
BYPASS
TRAY
BYPASS
TRAY
BYPASS
TRAY
81/2x11
PLAIN
81/2x11
PLAIN
81/2x11
PLAIN
81/2x11
PLAIN
(X)
1
2
(Y)
The tray name (tray position) selected for
insertion type A and the paper size and type are
shown in (X). If the tray in which you loaded
paper for insertion type A is shown, touch the
[OK] key. You will return to the screen of step 2.
If the correct tray for insertion type A does not
appear in (X), touch the (Y) key. The tray
selection screen will appear. Select the tray in
which you loaded paper for insertion type A. You
will return to the screen of step 2.
the [INSERTION TYPE A SETTING]
4 Touch
key in the screen of step 2
5-14
(Y)
(Z)
Select whether or not insertion type A paper is
to be copied on with the (X) keys ([YES] or
[NO]).
Select whether one-sided copying or two-sided
copying is to be performed on insertion type A
with the (Y) keys. This selection is only possible
when the [YES] key of (X) has been selected.
(The one-sided/two-sided selection made here
only applies to insertion type A paper. When
insertion type B is selected, the selection only
applies to insertion type B paper.)
The (Z) key shows the tray selected for insertion
type A in step 3 and the paper size and type.
If a paper tray with tabbed paper is selected in
the screen of step 3, you can touch the [TAB
COPY] key. This allows you to select the tab
width. Two-sided copying is not possible on
tabbed paper.
the [OK] key in the screen of step 5.
6 Touch
You will return to the screen of step 2.
When you return to the screen of step 2, the
[INSERTION TYPE A SETTING] key will be
highlighted.
wish to insert a different paper with
7 Iftheyou[INSERTION
TYPE B SETTING] key,
repeat steps 2 through 6. Use the
[INSERTION TYPE B SETTING] key instead
of the [INSERTION TYPE A SETTING] key,
and the [INSERTION TYPE B] key instead
of the [INSERTION TYPE A] key.
OK
CANCEL
TS
INSERTION
TYPE A SETTING
INSERTION
TYPE B SETTING
INSERTION
SETTINGS
OK
PAPER TRAY
SETTINGS
PAGE LAYOUT
dragonII_copy_sec.book
15 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
the [INSERTION SETTINGS] key to
8 Touch
specify the pages where you wish to insert
wish to insert a different paper with
11 Iftheyou[INSERTION
TYPE B SETTING] key,
the insert papers of [INSERTION TYPE A
SETTING] and [INSERTION TYPE B
SETTING].
repeat steps 2 through 6. Use the
[INSERTION TYPE B SETTING] key instead
of the [INSERTION TYPE A SETTING] key,
and the [INSERTION TYPE B] key instead
of the [INSERTION TYPE A] key.
CANCE
RTION
SETTING
INSERTION
SETTINGS
TION
SETTING
OK
INSERTION
TYPE A SETTING
INSERTION
TYPE B SETTING
the [INSERTION TYPE A] key or the
9 Touch
[INSERTION TYPE B] key, enter the page
number where you wish to insert the insert
paper with the numeric keys, and then
touch the [ENTER] key.
INPUT THE PAGE NUMBER AND
PRESS [ENTER]. USE [C] KEY TO AMEND.
OK
INSERTION SETTINGS
INSERTION PAGE
INSERTION
TOTAL:0
3
ENTER
(X)
1
2
3
4
INSERTION
TYPE A
INSERTION
TYPE B
BYPASS
TRAY
81/2x11
PLAIN
BYPASS
TRAY
81/2x11
PLAIN
(Y)
(Z)
OK
CANCEL
TS
INSERTION
SETTINGS
PAPER TRAY
SETTINGS
PAGE LAYOUT
the [PAGE LAYOUT] key in the
12 Touch
screen of step 11 to display a list of the
selected settings (page 5-16).
To edit or delete a cover/insert, follow
steps 1 and 2 on page 5-16. To exit the
cover/insert settings, touch the upper
[OK] key in the screen of step 11.
13 Press the [START] key.
To cancel covers/inserts settings...
Touch the [CANCEL] key in the screen of step 2.
(X) shows the total number of inserts. Up to 100
inserts can be added. When inserting multiple
inserts, touch the [ENTER] key after each entry
of an insertion page number (insertion position)
with the numeric keys.
(Y) shows the tray selected in step 3 for
[INSERTION TYPE A SETTING] and the paper
size and type.
(Z) shows the tray selected in step 3 for
[INSERTION TYPE B SETTING] and the paper
size and type.
When the [INSERTION TYPE A] key is
highlighted, the insert settings apply to
[INSERTION TYPE A SETTING]. When the
[INSERTION TYPE B] key is highlighted, the
insert settings apply to [INSERTION TYPE B
SETTING].
the [OK] key in the screen of step 9.
10 Touch
You will return to the screen of step 2.
When you return to the screen of step 2, the
[INSERTION TYPE A SETTING] key will be
highlighted.
5-15
5
dragonII_copy_sec.book
16 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
■ Checking, editing, and deleting cover/insert pages
The [PAGE LAYOUT] key appears after covers/inserts settings are configured (the settings of step 1 through
step 7 on pages 5-13 and 5-14).
The [PAGE LAYOUT] key is used for the following:
● To display the status of covers/inserts pages
● To edit, delete, or add inserted pages
3 To edit or delete an inserted page, touch the key
To display the [PAGE LAYOUT] key...
of the page you wish to edit or delete in the page
Configure the settings in step 1 through step 7
layout screen. When the key is touched, the
on pages 5-13 and 5-14.
[CANCEL], [DELETE], and [AMEND] keys
appear.
1 Touch the [PAGE LAYOUT] key.
AMEND THE INSERTION?
OK
INSERTION
TYPE A SETTING
INSERTION
TYPE B SETTING
INSERTION
SETTINGS
CANCEL
OK
CANCEL
TS
OK
PAGE LAYOUT
1/2
INSERTION
TYPE A
<4
INSERTION
TYPE B
7/8
INSERTION
TYPE A
12/-
1
If there are multiple screens, touch the
key to change screens.
2
Displayed icons:
: Front side copy only
: Back side copy only
: Two-sided copy
: No copying
For inserts, the insertion page also appears.
" " represents a page number.
/- : Front side copy only at page
/
5-16
AMEND
PAGE LAYOUT
2 The set covers/inserts pages are shown.
FRONT COVER
DELETE
PAPER TRAY
SETTINGS
: Two-sided copy at page
/
-/
: Back side copy only at page
<
: Insert non-copied insert at page
or
●To cancel, touch the [CANCEL] key.
●To delete an inserted page, touch the
[DELETE] key.
●To edit an inserted page, touch the [AMEND]
key. The screen of step 5 on page 5-13 or the
screen of step 5 on page 5-14 appears. Edit
the page as explained in step 5 on page 5-13
or step 5 on page 5-14.
you have finished
3 When
pages, touch the [OK] key.
OK
INSERTION
TYPE B
BYPASS
checking the
dragonII_copy_sec.book
17 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
■ Examples of covers and inserts
The relations between the originals and finished copies when covers or inserts are inserted are shown on the
following pages.
Covers
●Two-sided copying of one-sided originals
●One-sided copying of one-sided originals
(page 5-19)
(page 5-18)
●Two-sided copying of two-sided originals
●One-sided copying of two-sided originals
(page 5-21)
(page 5-20)
Inserts
●One-sided copying of one-sided originals
(page 5-22)
●One-sided copying of two-sided originals
(page 5-22)
●Two-sided copying of one-sided originals
(page 5-22)
●Two-sided copying of two-sided originals
(page 5-22)
■ Symbols used for covers and inserts
6
6
6
Inserts
Back cover
copied on.
1
not
Back cover after two-sided
copying. (One page is not
copied on.)
Back cover after two-sided
copying.
Icon
appearing
in display
1
6
5
5
one-sided
Insert after one-sided
copying. (One page is not
copied on.)
3
3
Back cover after one-sided
copying
of
one-sided
original.
Insert after
copying.
3
Front cover after two-sided
copying.
when
Meaning
Insert when not copied on.
4
2
Front cover
Front cover after two-sided
copying. (One page is not
copied on.)
1
Back cover
not
Front cover after one-sided
copying.
1
5
when
Symbol
Insert
after
copying.
two-sided
One-sided
original
or
output page of regular onesided copying
2
Front cover
copied on.
1
Icon
appearing
in display
Meaning
Type
Symbol
Other
Type
The following symbols are used to make the explanations easier to understand.
The numbers that appear indicate relations between the originals and copies, and will vary depending on the
settings.
Two-sided
original
or
output page of regular twosided copying.
One-sided
original
or
output page of regular onesided copying.
One-sided
original
or
output page of regular onesided copying.
5-17
dragonII_copy_sec.book
18 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
■ Covers (One-sided copying of one-sided originals)
One-sided copies are made of the following one-sided originals.
1st page
2nd page
2
1
3rd page
4th page
3
5th page
4
6th page
5
6
Copying on cover
Resulting copies
One-sided
copying
No copying
Two-sided
copying
No copying
No copying
3
4
5
1
2
3
4
5
6
1
3
4
5
6
One-sided
copying
1
2
3
4
5
Two-sided
copying
1
2
3
4
5
No copying
One-sided
copying
One-sided
copying
1
2
3
4
5
One-sided
copying
Two-sided
copying
1
2
3
4
5
Two-sided
copying
One-sided
copying
1
3
4
5
Two-sided
copying
Two-sided
copying
1
3
4
5
5-18
6
6
6
6
6
2
2
1
6
No copying
6
No copying
2
Back cover
2
Front cover
dragonII_copy_sec.book
19 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
■ Covers (Two-sided copying of one-sided originals)
Two-sided copies are made of the following one-sided originals.
1st page
2nd page
2
1
3rd page
4th page
3
5th page
4
6th page
5
6
Copying on cover
One-sided
copying
1
No copying
Two-sided
copying
1
No copying
One-sided
copying
One-sided
copying
1
2
One-sided
copying
Two-sided
copying
1
2
Two-sided
copying
One-sided
copying
1
2
3
Two-sided
copying
Two-sided
copying
1
3
3
2
1
4
6
5
6
No copying
2
4
Two-sided
copying
1
5
5
No copying
3
6
One-sided
copying
1
2
No copying
3
No copying
4
Back cover
2
Resulting copies
Front cover
6
6
6
6
5
5
6
4
5
4
3
4
4
3
4
5
5
2
3
5
6
2
3
4
5
5-19
dragonII_copy_sec.book
20 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
■ Covers (One-sided copying of Two-sided originals)
One-sided copies are made of the following two-sided originals.
5
Copying on cover
No copying
One-sided
copying
No copying
Two-sided
copying
No copying
No copying
3
4
5
1
2
3
4
5
6
1
3
4
5
6
One-sided
copying
1
2
3
4
5
Two-sided
copying
1
2
3
4
5
No copying
One-sided
copying
One-sided
copying
1
2
3
4
5
One-sided
copying
Two-sided
copying
1
2
3
4
5
Two-sided
copying
One-sided
copying
1
3
4
5
Two-sided
copying
Two-sided
copying
1
3
4
5
5-20
6
6
6
6
6
2
2
1
6
No copying
Resulting copies
2
Back cover
2
Front cover
6
3
3rd page
6
2nd page
4
1
2
1st page
dragonII_copy_sec.book
21 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
■ Covers (Two-sided copying of two-sided originals)
Two-sided copies are made of the following two-sided originals.
5
Copying on cover
2
3
One-sided
copying
One-sided
copying
1
3
4
One-sided
copying
Two-sided
copying
1
3
4
Two-sided
copying
One-sided
copying
1
2
3
4
Two-sided
copying
Two-sided
copying
1
3
4
4
3
5
6
6
5
5
6
5
6
4
2
5
6
Two-sided
copying
1
No copying
3
6
One-sided
copying
1
No copying
1
5
5
6
No copying
3
6
Two-sided
copying
1
3
6
No copying
2
One-sided
copying
1
4
No copying
4
No copying
2
Back cover
2
Resulting copies
Front cover
4
3
3rd page
6
2nd page
4
1
2
1st page
5-21
dragonII_copy_sec.book
22 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
■ Inserts (One-sided copying of one-sided originals)
One-sided and two-sided copying is performed using the following one-sided originals. The insert is added as
the third page.
1
3rd page
2
4th page
3
Copying on
insert
5th page
4
6th page
5
6
Resulting copies
(two-sided copying)
2
Two-sided
copying
1
2
5
3
4
5
6
3
5
6
6
1
4
1
4
5
3
4
5
One-sided
copying
3
6
3
5
6
2
3
2
1
2
Resulting copies (one-sided copying)
6
2nd page
2
1st page
1
1
4
4
No copying
■ Inserts (One-sided copying of two-sided originals)
One-sided and two-sided copying is performed using the following two-sided originals.
2
One-sided
copying
1
2
Two-sided
copying
1
2
3
4
5
3
4
5
6
3
5
6
6
1
3
2
1
5-22
3
5
6
3
5
6
4
1
2
1
2
4
No copying
5
6
Resulting copies
(two-sided copying)
Resulting copies (one-sided copying)
4
Copying on
insert
5
6
3
3rd page
4
1
2nd page
2
1st page
dragonII_copy_sec.book
23 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
Transparency film with insert sheets
When copying onto transparency film, blank insert sheets can be placed between transparent sheets.
Example: Inserting insert sheets between transparencies
● This function only operates in "one-sided to onesided" and "two-sided to one-sided" modes.
● Multiple copies cannot be selected in this mode.
● The inserts are inserted under each transparency
as shown at left.
● Select insert paper that is the same size as the
transparencies.
● When feeding insert paper from an inserter,
copying on the insert paper is not possible.
● Transparencies can be fed from the bypass tray
or tray 3.
● If the transparencies are loaded in tray 3, be sure
to set the paper size and paper type as explained
on pages 2-14 and 2-15.
Originals (1-sided)
Originals (2-sided)
Insert sheets
Two-sided originals are
only supported when
automatic
document
feeding is used.
Inserts can
copied on.
also
be
If the transparencies are loaded in tray 3, steps
1 to 5 below are not necessary.
4 Touch the [OK] key.
TYPE
TYPE/SIZE SETTING
OK
SIZE
transparency film into the bypass
1 Load
tray.
Remove any paper
already in the bypass
tray before loading the
transparency film. (To
load paper in the bypass
tray, see pages 2-10 and
2-11.)
the [PAPER SELECT] key in the
2 Touch
main screen and select the bypass tray
PLAIN
HEAVY PAPER
NON STANDARD SIZE
2/2
If the paper size was changed from an inch size to
an AB size, or from an AB size to an inch size, be
sure to set the paper type and size as explained on
steps 5 to 7 on page 2-14 and steps 8 to 10 on
page 2-15.
5 Select the bypass tray.
0
81/2x11
PLAIN
AUTO
ORIGINAL
Y
5. 81/2x11
AUTO
EXPOSURE
N
PLAIN
0
PLAIN
A4,B5
N
FOR COPY.
81/2x11
81/2X11
AUTO-AB
SIZE INPUT
paper type in the paper setting screen
(touch (X) below).
2. 81/2x11
AUTO-INCH
AUTO
ORIGINAL
AUTO
EXPOSURE
PAPER SELECT
100%
COPY RATIO
5. 81/2x11
PAPER SELECT
PLAIN
PLAIN
100%
COPY RATIO
(X)
3 Touch the [TRANSPARENCY] key.
TYPE.
LETTER HEAD
HEAVY PAPER
PRE-PUNCHED
LABELS
COLOR
TRANSPARENCY
To display the special modes screen...
See "General procedure for using special
functions" on page 5-2.
the [TRANSPARENCY INSERTS]
6 Touch
key in the special modes screen (2nd
screen).
SPECIAL MODES
COVERS/INSERTS
TRANSPARENCY
INSERTS
BOOK COPY
TAB COPY
The Transparency inserts
setting screen will appear.
The transparency inserts
icon (
, etc.) will also
appear in the upper left
corner of the screen to
indicate that the function
is turned on.
5-23
5
dragonII_copy_sec.book
24 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
the insertion conditions for the insert
7 Set
paper.
OK
CANCEL
PRINT ON INSERT SHEETS
YES
NO
You will return to the main screen of copy mode.
OK
INSERTION SHEET
TRAY5
81/2x11
PLAIN
(X)
the outer [OK] key in the screen of
8 Touch
step 7.
(Y)
1
Select whether or not the insert paper will be
copied on with the (X) keys ([YES] or [NO]). If
[YES] is selected, insert paper cannot be fed
from an inserter.
2
The (Y) key shows the tray selected for the insert
paper and the paper size and type. To select a
different tray, touch this key to display the tray
selection screen and select the tray that has the
insert paper.
NOTE
If insert paper is fed from an inserter, the output will
be delivered to the finisher (or saddle stitch finisher).
About the steps that follow
If an automatic document feeder is being used,
see pages 4-7 through 4-10. If the document
glass is being used, see pages 4-11 through 413.
To cancel the Transparency film with insert sheets
function, touch the [CANCEL] key on the
Transparency film with insert sheets setting screen.
Multi shot
Multiple original pages can be copied onto one sheet of copy paper in a uniform layout. Select 2in1 to copy two
original pages onto one sheet, or 4in1 to copy four original pages onto one sheet. This function is convenient when
you wish to present multiple pages in a compact format, or show a view of all pages in a document.
[Example] Copying 4 original pages onto one sheet of paper
(Page number : 4in1, layout : left top : right top (see the next page))
One-sided copies
one-sided originals
● When using the multi shot function, place the
originals, select the desired paper size, and
select the copying mode before selecting the
multi shot function on the special modes screen.
from
Copies
One-sided copies
two-sided originals
5-24
from
● When using the multi shot function, the
appropriate copy ratio will be automatically set
based on the original size, paper size, and the
number of originals to be copied onto one sheet.
The minimum reduction ratio is 25%. The
original size, copy paper size, and selected
number of original pages may require that the
ratio be less than 25%. As copying will take
place at 25% in this case, part of the original
images may be cut off.
dragonII_copy_sec.book
25 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
To display the special modes screen...
See "General procedure for using special
functions" on page 5-2.
the [MULTI SHOT] key in the special
1 Touch
modes screen (2nd screen).
TRANSPARENCY
INSERTS
MULTI SHOT
TAB COPY
CARD SHOT
The MULTI SHOT setting
screen will appear.
A multi shot icon ( ,
etc.) will also appear in
the upper left of the
screen to indicate that
the function is turned on.
the number of images to be copied
2 Select
onto one sheet of copy paper.
If
needed,
the
orientation of the copy
paper
and
the
orientation of the images
will be rotated.
SPECIAL MODES
MULTI SHOT
2in1
4in1
the [OK] key (inside [OK] key) on
4 Touch
the multi shot setting screen.
You will return to the special modes screen.
the [OK] key in the special modes
5 Touch
screen.
You will return to the main screen of copy mode.
About the steps that follow
If an automatic document feeder is being used, see
pages 4-7 through 4-10. If the document glass is
being used, see pages 4-11 through 4-13.
To cancel the multi shot function, touch the [CANCEL]
key in the multi shot setting screen (the screen of step
2).
3 Select the layout.
OK
CANCEL
LAYOUT
Shot number
OK
5
Select the order in which
the originals will be
arranged on the copy.
Layout
2in1
4in1
The arrows in the above diagram indicate the
directions in which the images are arranged.
5-25
dragonII_copy_sec.book
26 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
Book copy
This function is convenient when you wish to compile copies of books or other bound originals into an attractive
pamphlet format. The two pages of the open book are scanned as a set, and two pages each are copied onto the
front and back sides of the copy paper (four pages are copied onto one sheet of copy paper). This allows the copies
to be folded down the center and made into a pamphlet.
[Example] Book copying an 8-page pamphlet
Originals
● Scan the originals from the first page to the last
page. The order of copying will be automatically
adjusted by the machine.
● Either left binding (right to left turning) or right
binding (left to right turning) can be selected.
● Four originals will be copied onto one sheet.
Blank pages may be automatically produced at
the end depending on the number of the originals.
● If a saddle stitch finisher is installed, book copy
can be used in combination with the pamphlet
function to staple and fold the copies at the
centerline.
Finished copies are
folded in two.
Left binding
First page
First page
Right binding
First page
First page
To display the special modes screen...
See "General procedure for using special
functions" on page 5-2.
the [BOOK COPY] key in the special
1 Touch
modes screen (2nd screen).
SPECIAL MODES
COVERS/INSERTS
TRANSPARENCY
INSERTS
BOOK COPY
TAB COPY
You will return to the main screen of copy mode.
the originals on the document glass.
5 Place
(page 4-3)
Scan the original pages in
the following order:
Opened front and back
cover
Opened inside of front
cover and 1st page
Opened 2nd and 3rd
page
The
BOOK
COPY
setting
screen
will
appear. The book copy
icon ( , etc.) will also
appear in the upper left
corner of the screen to
indicate that the function
is turned on.
whether the book opens to the left or
2 Select
to the right, and touch the [OK] key in the
book copy setting screen.
LEFT
BINDING
the [OK] key in the special modes
4 Touch
screen.
Opened last page and
inside of back cover
sure that the desired paper size has
6 Make
been selected.
You will return to the
special modes screen.
RIGHT
BINDING
AUTO 11x17
PAPER SELECT
CO
SET
If the desired paper size
is not selected, select
the desired size.
100%
3
Select any desired cover settings.
CANCEL
NG
OK
RIGHT
BINDING
COVER
SETTING
If you wish to use a
different type of paper for
the cover, perform steps
4 to 12 on pages 5-6 to 57.
If you do not wish to use
a different type of paper,
continue from step 4.
the number of copies and any other
7 Select
desired copy settings, and then press the
8
[START] key.
Place the next two pages and press the
[START] key. Repeat until all pages have
been scanned, and then touch the [READEND] key.
When book copy is selected, two-sided
copying is automatically selected.
To cancel the book copy function, touch the [CANCEL] key
in the book copy setting screen (the screen of step 2).
5-26
dragonII_copy_sec.book
27 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
Tab copy
Copying is possible on the tabs of tabbed paper. Prepare appropriate originals for the tab captions.
[Example]
Original
Tabbed paper
Copy
Area A
INDEX
INDEX
Area B
Tab width
8-1/2" x 11" : Maximum of 5/8"
(A4 : Maximum of 20 mm)
●The tab caption is shifted by the amount of the tab width setting, so keep areas A and B blank.
Relations between originals and tabbed paper
Left binding
(normal top-bottom)
Prepare
originals
5
Originals placed
face up in the
document feeder
(Normal orderA-E)
Leading edge
of original
(Normal orderA-E)
Originals placed
on the document
glass
Tabbed
paper
Right binding
(Inverted top-bottom)
these
(Normal orderA-E)
Originals
Right binding
(Inverted top-bottom)
Load
tabbed
paper in the
bypass tray or
tray 3
(Normal orderA-E)
1
2
3
4
5
Leading edge
of original
Leading edge
of original
(Reverse orderE-A)
(Reverse
orderE-A)
(Normal
orderA-E)
(Normal
order A-E)
Feeding
direction
(Reverse orderE-A)
Feeding
direction
Feeding
direction
Result
(Top-bottom
normal)
(Top-bottom
reversed)
(Top-bottom
reversed)
5-27
dragonII_copy_sec.book
28 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
To display the special modes screen...
See "General procedure for using special
functions" on page 5-2.
the [TAB COPY] key in the special
1 Touch
modes screen (2nd screen).
SPECIAL MODES
COVERS/INSERTS
TRANSPARENCY
INSERTS
BOOK COPY
TAB COPY
The TAB COPY setting
screen will appear. A
tab copy icon ( ) will
also appear in the
upper left corner of the
screen to indicate that
the function is turned
on.
necessary, set the image shift width (tab)
2 Ifand
touch the [OK] key.
OK
CANCEL
OK
IMAGE SHIFT
1/2
(0 5/8)
inch
Set the image shift
width (tab) with the
and
keys.
The width can be set
from 0 to 5/8" (0 to 20
mm) in increments of 1/
8" (1 mm).
the [OK] key in the special modes
3 Touch
screen.
You will return to the main screen of copy mode.
4 Load tabbed paper in the bypass tray.
Place the tabbed paper
so that the edges with
the tabs are the trailing
edge.
To use tab paper in tray
3, set the paper type
setting of tray 3 to "TAB
PAPER" in the tray
settings of the system
settings (page 2-14).
To load tabbed paper in
tray 3, see "Loading tabbed paper" on page 2-6.
NOTE
The width of the tabbed paper can be up to 8-1/2" x
11" width (8-1/2") + 5/8" (or A4 width (210 mm) + 20
mm).
5-28
"TAB PAPER" for the paper type
5 Select
setting.
The paper type setting is explained in “Setting the
paper type and paper size” (page 2-14).
If you are using tray 3, see “Setting the paper size
when a special size is loaded” (page 2-17).
About the steps that follow
If an automatic document feeder is being used,
see pages 4-7 through 4-10. If the document
glass is being used, see pages 4-11 through 413.
When performing tab copying with a right
binding
If you are using left-binding tabbed paper for a right
binding, either stack the sheets in reverse order or
scan the originals in reverse order.(See the table on
the previous page.)
To cancel the tab copy function, touch the [CANCEL]
key in the tab copy setting screen (the screen of step
2).
dragon_05.fm
29 ページ
２００６年１１月２日　木曜日　午後１２時７分
SPECIAL MODES
Card shot
When copying a card, this function allows you to combine the front and back sides on a single sheet of paper.
Original
● Copying is only possible on standard size paper.
● A copy ratio cannot be selected when using this
function.
● The image cannot be rotated when using this
function.
Copy
CARD
CARD
Front of
card
CARD
Back of
card
Example:
Portrait
8-1/2" (A4) size
Example:
Landscape
8-1/2" (A4) size
the [PAPER SELECT] key and then
1 Touch
select the desired paper size.
READY TO SCAN FOR COPY.
1. 81/2 x11
2. 81/2x11
PLAIN
PLAIN
3. 81/2x11
HEAVY PAPER
4. 11x17
PLAIN
81/2x11
PLAIN
The selected paper size
key is highlighted and
the paper selection
screen closes.
the X dimension (width) and Y
3 Enter
dimension (length) of the original with the
keys.
CANCEL
OK
5
SIZE RESET
5. 81/2x11
PLAIN
FIT TO
PAGE
NOTE
If paper of the desired size is not loaded in any tray,
load paper of the required size in a paper tray or the
bypass tray. (See "Setting the paper type and paper
size" on page 2-14.)
To display the special modes screen...
See "General procedure for using special
functions" on page 5-2.
the [CARD SHOT] key in the special
2 Touch
modes screen (2nd screen).
TRANSPARENCY
INSERTS
MULTI SHOT
TAB COPY
CARD SHOT
●X (width) is initially selected. Enter X and then
touch the Y ( ) key to enter Y.
●To return the X and Y values to the initial
settings configured in the administrator
settings, touch the [SIZE RESET] key. (See
"CARD SHOT SETTINGS" on page 16 of the
administrator settings guide.)
●To have the images enlarged or reduced by a
suitable ratio based on the entered original
size so that the front and back sides fit into the
selected paper size, touch the [FIT TO PAGE]
key.
The CARD SHOT
setting screen will
appear. A card shot
icon ( , etc.) will also
appear in the upper left
corner of the screen to
indicate
that
the
function is turned on.
5-29
dragonII_copy_sec.book
30 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
4 Touch the outer [OK] key.
OK
CANCEL
OK
You will return to the
main screen of copy
mode.
the back side of the original face
8 Place
down on the document glass (see step 5).
9 Press the [START] key.
SIZE RESET
The back side of the
card is scanned.
FIT TO
PAGE
5 Place the original on the document glass.
Place the front side of
the original face down
and
close
the
document cover.
10Touch the [READ-END] key.
NOTE
steps 4 through 5 of "Copying from
6 Follow
the document glass" (page 4-12).
7 Press the [START] key.
The front side of the
card is scanned.
5-30
The original must be placed on the document glass.
The document feeder (automatic document feeding
function) cannot be used.
To cancel the card shot function, touch the
[CANCEL] key in the card shot setting screen (the
screen of step 4).
dragonII_copy_sec.book
31 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
Mirror image
This function is used to print a mirror image of the original. The images will be inverted in the right to left direction
on the copies.
Original
Copy
the [OK] key on the special modes
2 Touch
screen.
To display the special modes screen...
See "General procedure for using special
functions" on page 5-2.
the [MIRROR IMAGE] key in
1 Touch
special modes screen (3rd screen).
ECIAL MODES
MIRROR
IMAGE
B/W
REVERSE
You will return to the main screen of copy mode.
the
The [MIRROR IMAGE]
key will be highlighted to
indicate that the function
is turned on, and the
mirror image icon (
)
will appear in the upper
left of the screen.
About the steps that follow
If an automatic document feeder is being used,
see pages 4-7 through 4-10. If the document
glass is being used, see pages 4-11 through 413.
To cancel the mirror image function, touch the
[MIRROR IMAGE] key in the special modes screen
(the screen of step 1).
B/W reverse
Black and white are reversed in the copy to create a negative image.
NOTES
● When this function is selected, the exposure mode setting (page 4-14) automatically changes to "Text".
● Originals with large black areas (which use a large amount of toner) can be printed with black/white reverse
to reduce toner consumption.
Original
B/W reverse copy
the [OK] key in the special modes
2 Touch
screen.
To display the special modes screen...
See "General procedure for using special
functions" on page 5-2.
the [B/W REVERSE] key in
1 Touch
special modes screen (3rd screen).
ECIAL MODES
MIRROR
IMAGE
B/W
REVERSE
You will return to the main screen of copy mode.
the
The [B/W REVERSE]
key will be highlighted to
indicate that the function
is turned on, and the
mirror image icon (
)
will appear in the upper
left of the screen.
About the steps that follow
If an automatic document feeder is being used,
see pages 4-7 through 4-10. If the document
glass is being used, see pages 4-11 through 413.
To cancel the B/W reverse function, touch the [B/W
REVERSE] key in the special modes screen (the
screen of step 1).
5-31
5
dragonII_copy_sec.book
32 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
Print menu
The date, a stamp, page numbers, and entered text can be printed on copies. Four selections are available for the
PRINT MENU:
• Date print (page 5-35)
• Stamp (page 5-36)
This prints the date on the paper.
[Example] Printing 2010/APR/4 in the upper righthand corner of the paper
Print a message such as "CONFIDENTIAL" in
reverse text on the paper.
[Example] Printing "CONFIDENTIAL" in the upper
right-hand corner of the paper
2010/APR/4
The format of the date and the character that
separates the year, month, and day can be changed.
• Page numbering (page 5-37)
CONFIDENTIAL
One of 12 stamps can be selected.
• Text (page 5-41)
Page numbers can be printed on copies.
[Example] Printing page numbers in the bottom righthand corner of the paper
Entered text can be printed.
[Example] Printing "Meeting" in the upper left-hand
corner of the paper
Meeting
Up to 50 characters can be printed. You can store up
to 30 sequences of frequently used text.
The format of the page number can be changed.
Six printing positions are available: left, center, or right of the top or bottom of the page.
Each printing position is divided into an area for the date, page number, and text (A below), and an area for the stamp
(B below).
Top left
Top center
Bottom left
Top right
Print menu
Printing
area
Maximum number of
settings
DATE
A
One position only
STAMP
B
6 positions
PAGE
NUMBERING
A
One position only
TEXT
A
6 positions
Bottom right
Bottom center
NOTES
● A part that overlaps the printed text will not be copied.
● If the set text content overlaps the print content of another position, the central print content will be moved to the
bottom, the content on the left will be next, and the content on the right will be placed on top in that order such
that only the content visible at the top is printed. Content that is hidden due to overlapping will not be printed.
● The printed text will be printed at the set size regardless of the copy ratio or paper size.
● The printed text will also be printed at the set density regardless of the copy exposure.
● Some copy paper sizes may cause the printed contents to be cut off or the print position to shift.
● If a copy job with a print menu setting is saved using the document filing function, the print menu setting will not
be saved. If you wish to print a file saved in copy mode and use a print menu setting, use the special modes in
the Job settings / print screen (or the document filing print screen in the Web page if the machine is connected
to a network) to select the print menu setting. (A print menu setting cannot be selected when printing a file saved
in a mode other than copy mode.)
5-32
dragonII_copy_sec.book
33 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
■ Common operation procedure for using the print menu
To display the special modes screen...
See "General procedure for using special functions" on
page 5-2.
the [PRINT MENU] key in the special
1 Touch
modes screen (3rd screen).
B/W
REVERSE
The print menu setting
screen will appear. The
print menu icon ( ) will
also appear in the upper
left corner of the screen
to indicate that the
function is turned on.
PRINT MENU
2 Select the print position.
SPECIAL MODES
LAYOU
PRINT MENU
N
Six
positions
are
available: left, center,
or right of the top or
bottom of the page.
The touched key is
highlighted.
The keys indicating the print position appear as
follows depending on the state of the setting:
Not selected, print menu setting has not
been selected.
select print menu settings at another
4 To
print position, repeat steps 2 and 3.
NOTES
● If the [DATE], [PAGE NUMBERING], or [TEXT] key
is touched when other than a "STAMP" print menu
setting has been selected for the print position
selected in step 2, a message will appear. To
overwrite the previously set print content of the
print menu that you touched, touch the [YES] key.
To keep the previous settings, touch the [NO] key.
● The "DATE" and "PAGE NUMBERING" cannot be set
in multiple positions. If either of these keys is touched
when a date or page numbering setting has already
been configured, a message will appear asking you if
you wish to move the print settings to the position that
you selected in step 2. To move the print settings,
touch the [YES] key. Otherwise touch the [NO] key.
5 Touch the
key.
LAYOUT
OK
CANCEL
1/2
DATE
STAMP
PAGE
NUMBERING
TEXT
specify the orientation of the original,
6 To
touch the [ORIGINAL ORIENTATION] key.
PRINT MENU
Selected during selection of the print
menu setting.
Not selected, print menu setting has
already been selected.
The image displayed within each key varies
depending on the key position.
3 Select the print menu.
OK
LAYOUT
CANCEL
OK
1/2
DATE
PAGE
NUMBERING
STAMP
TEXT
OK
SPECIAL MODES
ORIGINAL ORIENTATION
LAYOUT
CANCEL
2-SIDED ORIGINAL TYPE
OK
2/2
PRINT ON COVERS/INSERTS WHEN COPYING ON COVERS/INSERTS
If you placed a two-sided original, touch the
[
] key to specify the binding style (book or
tablet). The icon of the selected binding style is
highlighted.
you are adding covers or inserts, select
7 Ifwhether
or not you wish to print on the
The settings screen of
the
print
menu
appears.
For information on
each of the print
menus,
see
the
settings of each.
● DATE (page 5-35) ● STAMP (page 5-36)
● PAGE NUMBERING (page 5-37) ● TEXT (page 541)
covers or inserts.
OK
SPECIAL MODES
PRINT MENU
ORIGINAL ORIENTATION
LAYOUT
CANCEL
2-SIDED ORIGINAL TYPE
OK
2/2
PRINT ON COVERS/INSERTS WHEN COPYING ON COVERS/INSERTS
If you do not wish to print on covers or inserts,
touch the checkbox to remove the checkmark.
NOTES
● If you are not copying on covers or inserts, printing will
not take place on these even if a checkmark appears.
● A page number is never printed on covers or
inserts, regardless of the above setting.
● If covers/inserts have been disabled in the
administrator settings, the checkbox will be grayed
out to prevent selection.
5-33
5
dragonII_copy_sec.book
34 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
the print layout if needed (page 58 Check
43).
OK
LAYOUT
OK
CANCEL
2-SIDED ORIGINAL TYPE
S WHEN COPYING ON COVERS/INSERTS
the [OK]
9 Touch
setting screen.
2
To display the layout
and print content of the
configured print menu,
touch the [LAYOUT]
key. The position can
be
changed
and
settings canceled if
needed.
NOTE
To cancel print menu...
Touch the [CANCEL] key in the screen of step 3.
key on the print menu
the [OK] key on the special modes
10 Touch
screen.
About the steps that follow
If an automatic document feeder is being used, see
pages 4-7 through 4-10.
If the document glass is being used, see pages 4-11
through 4-13.
Printing in combination with other special functions
When a print menu is combined with one of the following special modes, printing will reflect the selected special
mode.
Special modes
Printing operation
Margin shift
Like the copy image, the printed contents are shifted in accordance with the set margin.
Dual page copy
The print content is printed on each copy sheet.
Pamphlet copy
Book copy
The print content is printed on each page of the "book".
Multi shot
Card shot
The print content is printed on each copy sheet.
Covers/inserts
In the print menu settings, specify whether or not the print content is printed on covers and inserts.
NOTE
When combined with "Erase", "Job build", "Mirror image", "B/W reverse", or "Tab copy", printing takes place
normally at the set position on the paper.
5-34
dragonII_copy_sec.book
35 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
■ Printing the date on copies
The date can be printed on copies. Four selections each are available for the date format and the character that
separates the year, month, and day.
NOTE
The date must be previously set in the system settings. (See page 2-18.)
steps 1 and 2 of "Common
1 Follow
operation procedure for using the print
5 Select the pages to be printed on.
menu" (page 5-33).
2
CANCEL
CURRENT SETTING
Touch the [DATE] key.
OK
FIRST PAGE
2010/APR/04
ALL PAGES
OK
LAYOUT
CANCEL
DATE CHANGE
Select whether to print
on only the first page,
or all pages. The
touched
key
is
highlighted.
OK
1/2
DATE
STAMP
PAGE
NUMBERING
TEXT
6 Touch the [OK] key.
CANCEL
3
Select the date format.
CURRENT SETTING
OK
FIRST PAGE
2010/APR/04
DATE
The selected date format
is highlighted.
YYYY/MM/DD
If you selected [YYYY/
MM/DD/YYYY
MM/DD], [MM/DD/YYYY],
DD/MM/YYYY
or [DD/MM/YYYY], you
MM DD, YYYY
can select the character
that separates the year,
month, and date. Select [/] (slash), [.] (period), [-]
(hyphen), or [ ] (space).
4 Check the date and format.
The date to be printed
is
displayed
in
FIRST PAGE
CURRENT SETTING
"CURRENT SETTING"
2010/APR/04
in the selected format.
ALL PAGES
The date that appears
DATE CHANGE
is the date set in the
machine. If you need to
change the date, touch the [DATE CHANGE] key.
The following screen appears.
CANCEL
OK
ALL PAGES
DATE CHANGE
7
Continue from step 4 of "Common
operation procedure for using the print
menu" (page 5-33).
NOTE
To cancel a date print setting...
Touch the [CANCEL] key in the date selection screen.
(The screen of step 6.)
OK
DATE CHANGE
YEAR
MONTH
DAY
2010
04
04
Touch the key of the number (year, month, or day)
that needs to be changed, and then adjust the
number with the
or
key. When finished,
touch the [OK] key.
NOTE
If you select a non-existent date (for example, Feb. 30),
the [OK] key will gray out to prevent entry of the date.
5-35
5
dragonII_copy_sec.book
36 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
■ Printing a stamp (reverse text) on copies
A message such as "CONFIDENTIAL" can be printed in reverse text on copies.
The following 12 messages are available.
CONFIDENTIAL
PRIORITY
PRELIMINARY
FINAL
FOR YOUR INFO.
DO NOT COPY
IMPORTANT
COPY
URGENT
DRAFT
TOP SECRET
PLEASE REPLY
You can select from three density levels for the background of the stamp.
Two selections are available for the size of the stamp.
NOTE
The text of the stamp cannot be edited.
steps 1 and 2 of "Common
1 Follow
operation procedure for using the print
5 Select the desired stamp size.
menu" (page 5-33).
CANCEL
2 Touch the [STAMP] key.
1/2
CANCEL
FIRST PAGE
SIZE
LARGER
OK
LAYOUT
1
2
3
EXPOSURE
OK
ALL PAGES
SMALLER
OK
1/2
DATE
STAMP
PAGE
NUMBERING
TEXT
6 Select the pages to be printed on.
CANCEL
3 Select the stamp that you wish to print.
STAMP
1/2
CONFIDENTIAL
PRIORITY
FOR YOUR INFO.
DO NOT COPY
URGENT
DRAFT
The selected stamp is
highlighted.
If
the
desired stamp does not
appear,
change
screens with the
or
key.
4 Adjust the exposure as needed.
CANCEL
1
2
3
EXPOSURE
1/2
"LARGER" is initially
selected. To make the
stamp smaller, touch
the
[LARGER/
SMALLER]
key.
"Smaller" is selected
when [SMALLER] is
highlighted.
OK
FIRST PAGE
SIZE
ALL PAGES
LARGER
SMALLER
The density of the
background
of
the
stamp can be adjusted.
Touch the [EXPOSURE]
key to display the
following screen.
1/2
1
2
3
EXPOSURE
OK
FIRST PAGE
SIZE
LARGER
ALL PAGES
Select whether to print
on only the first page,
or all pages. The
touched
key
is
highlighted.
SMALLER
7 Touch the [OK] key.
CANCEL
1/2
1
2
3
EXPOSURE
OK
FIRST PAGE
SIZE
LARGER
ALL PAGES
SMALLER
from step 4 of "Common
8 Continue
operation procedure for using the print
menu" (page 5-33).
EXPOSURE
1
5-36
2
3
Touch the
key for a
darker
background.
Touch the
key for a
lighter background (3
levels).
When finished, touch
the [OK] key.
NOTE
To cancel a stamp setting...
Touch the [CANCEL] key in the stamp selection
screen. (The screen of step 7.)
dragonII_copy_sec.book
37 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
■ Printing the page number on copies
The page number can be printed on copies. One of 6 formats can be selected for the page number.
steps 1 and 2 of "Common
1 Follow
operation procedure for using the print
you need to change the starting or ending
4 Ifnumber
of page numbering, the first page
printed on, or the print settings for covers/
inserts, touch the [PAGE NUMBER] key.
menu" (page 5-33).
2 Touch the [PAGE NUMBERING] key.
TOTAL PAGE
OK
LAYOUT
CANCEL
AUTO
OK
MANUAL
1/2
DATE
STAMP
PAGE
NUMBERING
TEXT
OK
CANCEL
PAGE NUMBER
5 Touch the [MANUAL] key.
3 Select the page number format.
PAGE NUMBER
The selected format is
highlighted.
PAGE NUMBERING
PAGE NUMBERING FORMAT
FIRST NUMBER
AUTO
MANUAL
1,2,3..
(1),(2),(3)..
-1-,-2-,-3-..
P.1,P.2,P.3..
<1>,<2>,<3>..
1/5,2/5,3/5..
settings for
6 Enter
"LAST
NUMBER",
"FIRST NUMBER",
and
"PRINTING
STARTS FROM SHEET".
"PAGE NUMBER/TOTAL PAGES" will be printed.
"AUTO" is initially selected for "TOTAL PAGE",
which means that the number of scanned original
pages is automatically used. If you need to enter
the total pages manually (for example, when a
large number of originals are scanned in batches),
touch the [MANUAL] key to display the total page
entry screen.
CANCEL
PAGE NUMBERING
OK
PAGE NUMBERING FORMAT
OK
TOTAL PAGE
(1),(2),(3)..
-1-,-2-,-3-..
P.1,P.2,P.3..
<1>,<2>,<3>..
1/5,2/5,3/5..
PRINTING STARTS FROM
1
If you selected "1/5, 2/5, 3/5",
1,2,3..
LA
1
Touch each key so that
it is highlighted, and
FIRST NUMBER
LAST NUMBER
then enter the number
AUTO
1
with the numeric keys
(1 to 999).
PRINTING STARTS FROM SHEET
To return a number to
1
its initial value (FIRST
NUMBER: 1, LAST NUMBER: AUTO, PRINTING
STARTS FROM SHEET: 1), touch the [C] (clear)
key while the key of the number is highlighted. If
you enter the wrong number, press the [C] (clear)
key and enter the correct number.
TOTAL PAGE
AUTO
30
MANUAL
PAGE
Enter the total pages (1 to 999) with the numeric
keys and touch the [OK] key.
NOTES
● When two-sided copying is performed, each side of
the paper is counted as a page. If the last page is
blank, it will not be included in the total pages.
However, if [COUNT BACK COVER] is selected,
the last page will be counted. (See step 7.)
● When used in combination with "Dual page copy",
"Multi shot", or "Card shot", the number of copied
images is the total pages.
● When used in combination with "Pamphlet copy" or
"Book copy", the number of pages in the "book" is
the total pages.
NOTES
● A last number smaller than the "FIRST NUMBER"
cannot be set.
● "LAST NUMBER" is initially set to "AUTO", which
means that the page number is printed on each
page through the final page in accordance with the
"FIRST NUMBER" and "PRINTING STARTS
FROM SHEET" settings.
● A number less than the total page number is set as
the last number, the page number will not be
printed on the pages that follow the set number.
● Unlike the first and last page numbers, "PRINTING
STARTS FROM SHEET" specifies the sheet of paper
(not the page number) from which printing of the page
number begins.
For example, when "3" is selected for one-sided
copying, printing of the page number will start from the
3rd sheet of copy paper (the copy of the 3rd original
page). When "3" is selected for two-sided copying,
printing of the page number will start from the 3rd sheet
of copy paper, which is the copy of the 5th original page.
5-37
5
dragonII_copy_sec.book
38 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
covers/inserts are added and you
7 When
wish to include the covers/inserts in the
9 Touch the [OK] key.
page number count, touch the [COVERS/
INSERTS COUNTING] key.
OK
LAST NUMBER
OK
AUTO
COVERS/INSERTS
COUNTING
LAST NUMBER
AUTO
8
COVERS/INSERTS
COUNTING
10 Touch the [OK] key.
Select the checkboxes of the items that
you wish to include in the page number
count and then touch the [OK] key.
TOTAL PAGE
OK
COVERS/INSERTS COUNTING
OK
CANCEL
AUTO
COUNT FRONT COVER
MANUAL
PAGE NUMBER
COUNT INSERTS
2
COUNT BACK COVER
1
Front cover
image
Insert
image
from step 4 of "Common
11 Continue
operation procedure for using the print
Back cover
image
menu" (page 5-33).
Items that are selected are reflected in the print
image on the right side of the screen.
NOTE
To cancel a page number setting...
Touch the [CANCEL] key in the page number
selection screen. (The screen of step 10.)
NOTES
● When an item is selected, one inserted sheet (front
cover, insert, or back cover) is counted as one page
during one-sided copying, and two pages during
two-sided copying. However, if one-sided copying
is used for the body pages and two-sided copying is
used for the inserted sheets, each body page will
be counted as one page and each inserted sheet
will be counted as two pages.
● Printing never takes place on the front cover and back
cover, regardless of whether or not these are counted.
● To print on an insert, the insert must be counted
and it must be copied on.
NOTES
● Copying in group mode is not possible when page number printing is selected. The mode will automatically switch to sort mode.
● When the page number print position is set to the left or right side and "Pamphlet copy" or "Book copy" is
selected, the position of the page numbers will alternate so that they are always on the outside when the
pamphlet/book is opened. If a stamp is set in an area with a page numbering setting, the position of the stamp
will alternate in the same way.
If another item is set in a position that changes, that item will appear in the position that alternates with the page
number position.
Print menus not related to the alternating print positions will appear in their set positions.
[Example] When the page number format "1, 2, 3.." is selected when performing pamphlet copying of 4 pages,
the copies will appear as shown below.
In this example, the page number is at the bottom of the page and the date is at the top, so the
position of the date does not change.
Print settings
2010/APR/4
Date
Stamp
Page numbering
5-38
Front
CONFIDENTIAL
Text
4
Back
2010/APR/4
2010/APR/4
CONFIDENTIAL
Minutes of meeting Minutes of meeting
1
CONFIDENTIAL
2
2010/APR/4
CONFIDENTIAL
Minutes of meeting Minutes of meeting
3
dragonII_copy_sec.book
39 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
Examples of page number printing
Page number printing during one-sided copying (5 originals)
Setting
Value
1st page
2nd page
3rd page
4th page
5th page
A
1/5
B
2/5
C
3/5
D
4/5
E
5/5
FIRST NUMBER: 11
11/15
12/15
13/15
14/15
15/15
FIRST NUMBER: 11
LAST NUMBER: 13
11/13
12/13
13/13
1/2
2/2
11/15
12/15
TOTAL PAGE
AUTO
FIRST NUMBER
1
LAST NUMBER
AUTO
PRINTING STARTS
FROM SHEET
1
Printed contents when
settings are changed as
follows
TOTAL PAGE: 2
TOTAL PAGE: 15
FIRST NUMBER: 11
LAST NUMBER: 13
Not printed Not printed
Not printed Not printed Not printed
13/15
PRINTING STARTS FROM SHEET: 3 Not printed Not printed
Not printed Not printed
1/3
2/3
3/3
Page number printing during two-sided copying (9 originals)
Setting
Value
TOTAL PAGE
2nd page
3rd page
4th page
5th page
Front
Back
Front
Back
Front
Back
Front
Back
Front
A
1/9
B
2/9
C
3/9
D
4/9
E
5/9
6/9
F
G
7/9
H
8/9
9/9
Not
printed
Not
printed
Not
printed
Not
printed
1/5
2/5
3/5
4/5
5/5
Back
AUTO
FIRST
NUMBER
1
LAST NUMBER
AUTO
PRINTING
STARTS FROM
SHEET
1
Printed contents
when settings
are changed as
follows
1st page
PRINTING
STARTS
FROM
SHEET: 3
I
5
Not
printed
Page number printing during one-sided copying of body pages with covers inserted (4 originals)
Setting
TOTAL PAGE
Value
1
LAST NUMBER
AUTO
COUNT FRONT COVER
2nd page
3rd page
4th page
5th page
A
1/4
B
2/4
C
3/4
D
4/4
Not printed Not printed
1/3
2/3
3/3
Not printed
(count)
2/5
3/5
4/5
5/5
Not printed
(count)
1/4
2/4
3/4
4/4
AUTO
FIRST NUMBER
PRINTING STARTS
FROM SHEET
1st page
(Front
cover)
1
Not selected
PRINTING STARTS
FROM SHEET: 2
COUNT FRONT
Printed contents when
COVER: Selected
settings are changed
COUNT FRONT
as follows
COVER: Selected
PRINTING STARTS
FROM SHEET: 2
When a back cover is inserted, page numbers are counted and printed in the same way.
Note that page numbers are never printed on front and back covers.
5-39
dragonII_copy_sec.book
40 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
Page number printing during two-sided copying of body pages with covers (one-side copying) inserted (9 originals)
Setting
Value
TOTAL PAGE
AUTO
FIRST NUMBER
1
LAST NUMBER
AUTO
PRINTING
STARTS
FROM SHEET
1
COUNT FRONT
COVER
Not selected
1st page
(front cover)
Front
Printed
contents
when
settings are
changed as
follows
Back
2nd page
Not
printed
Not
printed
Not
Not
printed printed
(count) (count)
5th page
Back
Front
Back
Front
Back
Front
Back
B
1/8
C
2/8
D
3/8
E
4/8
5/8
F
G
6/8
H
7/8
8/8
Not
printed
Not
printed
Not
printed
Not
printed
1/4
2/4
3/4
4/4
3/10
4/10
5/10
6/10
7/10
8/10
9/10
10/10
Not
printed
Not
printed
1/6
2/6
3/6
4/6
5/6
6/6
Not printed Not printed
COUNT FRONT
(count)
(count)
COVER: Selected
COUNT FRONT
COVER: Selected
PRINTING STARTS
FROM SHEET: 3
4th page
Front
A
PRINTING STARTS
FROM SHEET: 3
3rd page
I
When a back cover is inserted, page numbers are counted and printed in the same way.
Note that page numbers are never printed on front and back covers.
Page number printing during one-sided copying with inserts (4 originals; 5 originals when copying on inserts)
1st page
2nd page
3rd page
(insert)
4th page
5th page
A
1/4
B
2/4
C
D
3/4
E
4/4
PRINTING STARTS FROM SHEET: 3 Not printed Not printed Not printed
1/2
2/2
COUNT INSERTS: Selected
3/5 (count)
4/5
5/5
COUNT INSERTS: Selected
Not printed Not printed 1/3 (count)
PRINTING STARTS FROM SHEET: 3
2/3
3/3
Not printed
(count)
4/5
5/5
COUNT INSERTS: Selected
Not printed
Not printed Not printed
PRINTING STARTS FROM SHEET: 3
(count)
2/3
3/3
Setting
Value
TOTAL PAGE
AUTO
FIRST NUMBER
1
LAST NUMBER
AUTO
PRINTING STARTS FROM
SHEET
1
COUNT INSERTS
Not selected
Printed contents when
copying on inserts and
settings are changed as
follows
Printed contents when not
copying on inserts and
settings are changed as
follows
1/5
COUNT INSERTS: Selected
2/5
1/5
2/5
When inserts are not copied on, the page number is not printed.
Page number printing during two-sided copying of body pages with inserts (one-side copying) (9 originals)
Setting
TOTAL PAGE
Value
2nd page
3rd page
(insert)
Front
Back
Front
Back
Front
A
1/8
B
2/8
C
3/8
D
4/8
E
1/10
2/10
3/10
4/10
5/10
Back
4th page
5th page
Front
Back
Front
Back
5/8
F
G
6/8
H
7/8
8/8
7/10
8/10
9/10
10/10
AUTO
FIRST NUMBER
1
LAST NUMBER
AUTO
PRINTING STARTS
FROM SHEET
1st page
1
I
COUNT INSERTS Not selected
Printed contents
when settings are
changed as follows
5-40
COUNT
INSERTS:
Selected
Not
printed
(count)
dragonII_copy_sec.book
41 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
■ Printing entered text on copies
Entered text can be printed on copies. Up to 50 characters can be printed.
Up to 30 sequences of frequently used text can be stored. See "Storing text sequences" (page 5-42).
NOTE
When the machine is connected to a network, the printed text sequences can be stored and deleted in the Web
page. For details, see Help in the Web page.
steps 1 and 2 of "Common
1 Follow
operation procedure for using the print
5 Touch the [OK] key.
menu" (page 5-33).
2 Touch the [TEXT] key.
04
05
OK
06
LAYOUT
CANCEL
OK
1/2
DATE
STAMP
PAGE
NUMBERING
TEXT
To edit the selected text
sequence, touch the
3
DIRECT ENTRY
6
[DIRECT ENTRY] key
1/5
to display the character
entry screen. The
selected text sequence
is
entered.
For
information on entering characters, see page 7-29.
When finished, touch the [OK] key to close the
character entry screen.
CANCEL
you wish to use one of the preset text
3 Ifsequences,
touch the [RECALL] key. To
6 Select the pages to be printed on.
CANCEL
directly enter the text, touch the [DIRECT
ENTRY] key.
CANCEL
TEXT
OK
FIRST PAGE
ALL PAGES
OK
FIRST PAGE
OK
Select whether to print
on only the first page,
or all pages. The
touched
key
is
highlighted.
DIRECT ENTRY
PRE-SET
ALL PAGES
RECALL
STORE/DELETE
DIRECT ENTRY
If you touch the [DIRECT ENTRY] key, a character
entry screen will appear. For information on
entering characters, see page 7-29. When
finished, click the [OK] key to close the character
entry screen. (Go to step 6.)
stored text sequences will appear as
4 The
keys. Touch the key of the desired text
sequence.
CANCEL
TEXT
3
RECALL
No.01 TARO YAMADA
No.04
No.02 Meeting
No.05
No.03
No.06
6
OK
DIRECT ENTRY
7 Touch the [OK] key.
CANCEL
OK
FIRST PAGE
ALL PAGES
DIRECT ENTRY
from step 4 of "Common
8 Continue
operation procedure for using the print
menu" (page 5-33).
1/5
The selected text sequence key is highlighted.
If the desired text sequence key does not appear,
change screens with the
or
key.
The display is initially set to show 6 keys per
screen. This can be changed to 3 keys per screen
by touching the [3 6] key. When 3 keys are
displayed, the entire text sequence will appear in
each key. (When 6 keys are displayed, up to 22
characters appear in each key.)
NOTE
To cancel a text setting...
Touch the [CANCEL] key in the text print screen. (The
screen of step 7.)
5-41
5
dragonII_copy_sec.book
42 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
Storing text sequences
1
Editing and deleting stored text
Follow steps 1 and 2 of "Common
operation procedure for using the print
menu" (page 5-33).
2 Touch the [TEXT] key.
steps 1 and 2 of "Common
1 Follow
operation procedure for using the print
menu" (page 5-33).
2 Touch the [TEXT] key.
OK
LAYOUT
CANCEL
OK
LAYOUT
OK
CANCEL
OK
1/2
1/2
DATE
STAMP
DATE
STAMP
PAGE
NUMBERING
TEXT
PAGE
NUMBERING
TEXT
3 Touch the [STORE/DELETE] key.
3 Touch the [STORE/DELETE] key.
PRE-SET
RECALL
PRE-SET
STORE/DELETE
RECALL
a key
4 Touch
programmed (a
that has not been
key in which No. xx
the text key that you wish to edit or
4 Touch
delete.
appears).
TEXT
3
STORE/DELETE
TEXT
3
STORE/DELETE
No.01 TARO YAMADA
No.04
No.02 Meeting
No.05
No.03
No.06
6
BACK
1/5
When touched, the character entry screen
appears. Enter the text (max. 50 characters). For
information on entering characters, see page 7-29.
When finished, touch the [OK] key to close the
character entry screen.
If no free keys appear, change screens with the
or
key.
6
04 Minutes of meeting
No.01 TARO YAMADA
No.02 Meeting
No.05
No.03
No.06
1/5
05
06
6 Touch the [BACK] key.
3
6
04 Minutes of meeting
05
06
5-42
BACK
1/5
When the [AMEND] key is
touched, the character
A TEXT HAS BEEN ALREADY STORED TO
LOCATION. CHANGE THE TEXT?
entry screen appears.
The
selected
text
CANCEL
DELETE
AMEND
sequence is entered. For
No.06
information on entering
characters, see page 729. When finished, touch the [OK] key to close the
character entry screen.
If you touch the [DELETE] key, the text will be deleted
and you will return to the screen of step 4.
To cancel editing or deletion, touch the [CANCEL] key.
The entered text is
stored.
BACK
6
No.04 Minutes of meeting
edit the text, touch the [AMEND] key. To
5 To
delete the text, touch the [DELETE] key.
5 Touch the [BACK] key.
3
STORE/DELETE
BACK
1/5
dragonII_copy_sec.book
43 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIAL MODES
■ Checking and changing the print layout
You can check the print layout after the print items have been selected. If needed you can change the print
position or delete print content.
the [LAYOUT] key on the print menu
1 Touch
screen.
4 Touch the key of the new position.
The selected key is
highlighted and the
print position changes
to the new position.
OK
LAYOUT
DATE
STAMP
PAGE
NUMBERING
TEXT
SELECTED ITEM.
OK
CANCEL
1/
the key in which you wish to change
2 Touch
the print position or delete print content.
The keys indicating the print position appear as
follows depending on the state of the setting:
Print position without any set print
menus.
OK
LAYOUT
TARO YAMADA
CONFIDENTIAL
Currently set print position.
DO NOT COPY
Print position with another competing
print menu set.
(When moving a stamp, this indicates
that another stamp has been set. When
moving a print menu other than a stamp,
this indicates that the date, page number,
or text has been set.)
1,2,3..
NOTE
Up to 14 characters of the print text appears in the
key.
3
To change the print position, touch the
[MOVE] key. To delete print content, touch
the [DELETE] key.
DO YOU WANT TO MOVE OR DELETE THE
SELECTED ITEM?
CANCEL
DELETE
MOVE
1,2,3..
If you touched the
[MOVE] key, the new
position
selection
screen appears.
If you touched the
[DELETE] key, the print
content is deleted. (Go
to step 6.)
NOTE
If you wish to swap the contents of two positions,
temporarily move the content of one position to an
unused position and then complete the swap.
5 Touch the [OK] key.
If you attempt to move
print content to a
position that already
has print content set, a
message will appear
asking you if you wish
to
overwrite
the
previously set content.
To overwrite the content, touch the [YES] key. To
cancel the move and return to the condition before
the [OK] key was touched, touch the [NO] key.
OK
6 Touch the [OK] key.
OK
CONFIDENTIAL
DO NOT COPY
1,2,3..
5-43
5
dragon_05.fm
44 ページ
２００６年１０月１９日　木曜日　午後１時０分
STORING, USING AND DELETING
JOB PROGRAMS
The steps of up to 10 copy jobs can be stored as job programs. Job programs can be called up with ease, and are
retained even when the power is turned off. By storing frequently used copy settings in a job program, you can
eliminate the bother of selecting the settings each time you use them for a copy job.
●If any settings related to the steps of a job program are changed in the administrator settings after the job program
is stored, the steps related to the changed settings will not be included when the job program is called up.
●To exit the job programs mode, press the [CA] (clear all) key on the operation panel or touch the [EXIT] key on the
touch panel.
Storing a job program
1 Press the [#/P] key.
5 Touch the [OK] key.
NCEL
OK
AUTO
ORIGINAL
LOGOUT
The selected settings
will be stored in the
number key selected in
step 3.
AUTO
2 Touch the [STORE/DELETE] key.
M NUMBER.
RECALL
STORE/DELETE
the number key ([1] to [10]) in which
3 Touch
you wish to store the job program.
Number keys in which
job
programs
are
already
stored
are
highlighted.
PROGRAMS
ESS PROGRAM NUMBER.
RECALL
STORE/
the copy settings that you wish to
4 Select
store in the job program.
The number of copies
cannot be stored.
TO STORE, MAKE SELECTIONS AND PRESS
[OK], TO DELETE, PRESS [CANCEL].
SPECIAL MODES
2-SIDED COPY
OUTPUT
1.
2.
81/2 x11 81/2x11
3. 81/2 x14
4. 11x17
5-44
■ If a number key is selected in step 3 that has
already been programmed.
A setting confirmation screen will appear. To replace
the existing program with the new program, touch
the [STORE] key and continue from step 4. If you do
not wish to replace the existing program, touch the
[CANCEL] key to return to the screen of step 3 and
select a different number key.
NOTE
If overwriting of programmed copy settings has been
prohibited in the administrator settings, it will not be
possible to store or delete a job program. (See page
17 of the administrator settings guide.)
dragon_05.fm
45 ページ
２００６年１０月１９日　木曜日　午後１時１分
STORING, USING AND DELETING JOB PROGRAMS
Calling up a job program
1 Press the [#/P] key.
the number of copies if needed and
3 Set
then press the [START] key.
Copying will begin using
the settings of the job
program.
LOGOUT
the number key of the desired job
2 Touch
program.
The
screen
automatically closes and
the job program is called
up. A number key that
does not have a job
program cannot be
selected.
JOB PROGRAMS
PRESS PROGRAM NUMBER.
RECALL
Deleting a stored job program
1 Press the [#/P] key.
5
4 Touch the [DELETE] key.
The selected program is
deleted and you return
to the screen of step 3.
To return to the screen of
CANCEL
DELETE
STORE
RECALL
STORE/DELETE
step 3 without deleting
the job program, touch
the [CANCEL] key. In
both cases, touch the
[EXIT] key displayed in the screen of step 3 to exit
the job program mode.
A JOB PROGRAM HAS BEEN ALREADY STORED
IN THIS LOCATION.
LOGOUT
2 Touch the [STORE/DELETE] key.
M NUMBER.
NOTE
RECALL
If overwriting of programmed copy settings has been
prohibited in the administrator settings, it will not be
possible to store or delete a job program. (See page
17 of the administrator settings guide.)
STORE/DELETE
a storage register number of the
3 Select
program to be deleted.
EXIT
STORE/DELETE
If a number key for which
no job program has been
stored is selected, the
screen will change to the
screen of step 4 on the
previous page for storing
a job program.
5-45
dragonII_copy_sec.book
46 ページ
２００６年１０月１８日　水曜日　午後７時３９分
INTERRUPTING A COPY RUN
The copy of the original scanned in interrupt mode is output before the remainder of the interrupted copy job.
1 Touch the [INTERRUPT] key.
If interrupt copying is
possible during a copy
run, the [INTERRUPT]
AUTO
ORIGINA key will appear. (If the
AUTO key does not appear,
EXPOSUR interrupt copying is not
AUTO A4 possible.)
INTERRUPT
23
81/2 x11
0
CANCEL
ORIGINAL
A4
AUTO
EXPOSURE
AUTO 81/2x11
PAPER SELECT
100%
COPY RATIO
When the [INTERRUPT]
key is touched in step 1,
the [INTERRUPT] key
will be replaced by the
[CANCEL] key as shown
in the illustration.
the original for the interrupt copy job
2 Place
in the document feeder or on the
document glass (page 4-3).
the exposure mode, paper size,
3 Select
number of copies, and any other copy
settings as needed, and then press the
[START] key.
To cancel an interrupt
copy job while the interrupt original is being
scanned or while you are selecting copy settings,
touch the [CANCEL] key.
NOTES
● If you touch the [INTERRUPT] key when auditing
mode is enabled, the display will prompt you to
enter your account number. Enter your account
number with the numeric keys. The copies you
make will be added to the count of the entered
account number.
● If a copy is being printed when the [INTERRUPT]
key is pressed, interrupt mode will begin after the
copy is finished.
● If the copy run to be interrupted is using paper
from the bypass tray, the paper size and type of the
bypass tray cannot be changed for use by the
interrupt job.
● If the document glass is used for an interrupt copy
job, two-sided copying, sort copying, and staple
sort copying cannot be selected. If any of these
functions are necessary, use the document feeder.
5-46
previous copy job automatically
4 The
resumes after the interrupt job finishes.
dragonII_copy_sec.book
1 ページ
２００６年１０月１８日　水曜日　午後７時３９分
CHAPTER 6
MACHINE MAINTENANCE
(FOR COPYING)
This chapter explains procedures for cleaning the machine, and
troubleshooting.
Page
USER MAINTENANCE ........................................................................... 6-2
● Cleaning the document glass and the automatic document feeder ....... 6-2
TROUBLESHOOTING ............................................................................ 6-3
6-1
dragonII_copy_sec.book
2 ページ
２００６年１０月１８日　水曜日　午後７時３９分
USER MAINTENANCE
To ensure good service from this product over a long period of time, it is recommended that the following
maintenance procedures be performed on a regular basis.
CAUTION
Do not use flammable spray to clean the machine. If gas from the spray comes in contact with hot electrical
components or the fusing unit inside the machine, fire or electrical shock may result.
NOTE
When cleaning, do not use thinner, benzene, or similar volatile cleaning agents.
Cleaning the document glass and the automatic document
feeder
If the document glass, document cover or automatic document scanning unit have dirty spots, these spots will form
lines in scanned images. These will show up as defects when the images are printed. Always keep these parts clean.
Wipe with a clean, soft cloth. If necessary, moisten the
cloth with water or a small amount of neutral detergent.
When finished, wipe dry with a clean cloth.
scanning unit (
and
If black or white stripes
appear
on
printed
images of originals that
were fed through the
automatic
document
feeder, wipe the long
narrow glasses in the
in the illustration).
Example of dirty print image
Black stripes
6-2
White stripes
dragon_06.fm
3 ページ
２００６年１０月１９日　木曜日　午後１時１分
TROUBLESHOOTING
Check the following troubleshooting list before requesting service as many problems can be fixed by the user. If you
are unable to solve the problem by checking the list, turn off the main power switch and the power switch, and unplug
the power cord.
Problems related to the copy function are described below. For problems related to general use of the machine, see
page 2-32.
Problem
Check
Solution
Machine does not Is the [START] key indicator off?
operate.
This indicates that the machine is warming
up (warming up lasts no more than 120
seconds after the power switch is turned on).
Copying is not possible during this time. Wait
until the [START] key light illuminates.
Copies are too dark Is the original image too dark or too light?
or too light.
Select an appropriate exposure mode for the
original being copied and adjust the copy
exposure. (See page 4-14.)
Is the exposure mode set to "AUTO"?
The exposure level for "AUTO" can be
adjusted using "Exposure adjustment" in the
administrator settings. Contact your
administrator. (See page 16 of the
administrator settings guide.)
An appropriate exposure mode for the
original has not been selected.
Change the exposure mode to "AUTO" or
manually select an appropriate resolution
setting. (See page 4-14.)
Text is not clear on a An appropriate exposure mode for the
copy.
original has not been selected.
Change the exposure mode to "TEXT". (See
page 4-14.)
Smudges appear on Document glass or document cover dirty?
Clean regularly. (See page 6-2.)
copies.
Black lines appear on copies when the Clean the original scanning area. (See page
automatic document feeding function is 6-2.)
used.
Original smudged or blotchy?
Image cannot
rotated.
be Is the auto paper select or auto image
function selected?
Use a clean original.
Rotation copy functions only if the machine
is either in the auto paper select mode or in
the auto image mode. (See page 4-15.)
Part
of
original
image is not copied.
Is the original positioned correctly?
Set the original properly. (See page 4-3.)
Is the copy ratio proper for the original and
paper sizes?
Use the auto image function to select the
appropriate copy ratio based on the original
and copy sizes. (See page 4-15.)
Blank copies
Is the original placed correctly?
When using the document glass, place the
original face down.
When using the automatic document feeder,
place original face up. (See page 4-3.)
copies Is the order of originals correct?
When using the document glass, place the
originals from the first page one sheet at a
time.
When using the automatic document feeder,
place the originals with the first page up.
Order of
incorrect
Job
cancelation Is a message requesting cancelation of job Press the [CA] key to cancel the current job.
needed
displayed?
6-3
6
dragonII_copy_sec.book
4 ページ
２００６年１０月１８日　水曜日　午後７時３９分
dragonII_copy_sec.book
1 ページ
２００６年１０月１８日　水曜日　午後７時３９分
CHAPTER 7
DOCUMENT FILING
FUNCTION
Page
OVERVIEW ............................................................................................. 7-2
● Document filing function.................................................................. 7-2
TO USE THE DOCUMENT FILING FUNCTION..................................... 7-4
● A look at the operation panel .......................................................... 7-4
● Saving files...................................................................................... 7-4
● Main screen of document filing ....................................................... 7-5
● Document filing icons ...................................................................... 7-5
SAVING A DOCUMENT IMAGE FILE .................................................... 7-6
● Quick File ........................................................................................ 7-6
● Filing................................................................................................ 7-7
● Print jobs ......................................................................................... 7-9
● Scan Save ....................................................................................... 7-10
CALLING UP AND USING A FILE.......................................................... 7-13
● Searching for and calling up a saved file......................................... 7-13
● Calling up and using a saved file..................................................... 7-15
SYSTEM SETTINGS .............................................................................. 7-24
● Creating, editing, and deleting user names and folders.................. 7-24
ENTERING CHARACTERS.................................................................... 7-29
TROUBLESHOOTING ............................................................................ 7-31
7-1
dragonII_copy_sec.book
2 ページ
２００６年１０月１８日　水曜日　午後７時３９分
OVERVIEW
Document filing function
The document filing function allows you to save a document image in the machine's hard disk as a data file. The
image can be called up and printed or transmitted as needed.
The scanned document image is saved when printing or transmitting a document in copy mode, printer mode, or
image send mode ("QUICK FILE" or "FILE"). A document can also be scanned and saved without being printed,
copied, or transmitted ("scan save").
To allow you to search for the file and call it up, names (user name, file name, etc.) can be assigned to the file (except
when using Quick File).
■ Data flow
Printing in copy mode (Quick
File saving, page 7-6)
Machine hard disk
Printing from a computer (printer
data, page 7-9)
Transmission in fax/image send
mode (filing, page 7-7)
Print
Save to machine's
hard disk
HDD
Call up a saved
file to reuse it.
Send
(facsimile or image send
function must be required)
and
Scanning a document only
(scan save, page 7-10)
Machine hard disk
QUICK FILE FOLDER
Data is saved by job
MAIN FOLDER
A user name and file name is
specified for each saved job
File 1
File 1
File 2
File 2
A password
can be set
CUSTOM FOLDER
A user name and file name can
be specified for each file and
the file saved to a folder with
any desired name assigned.
Folder 1
A password
can be set
Folder 2
Folder 3
File 1
File 2
●A stored file can be moved to a different folder under certain conditions (page 7-22).
7-2
A password
can be set
dragonII_copy_sec.book
3 ページ
２００６年１０月１８日　水曜日　午後７時３９分
OVERVIEW
■ Quick File folder
When [QUICK FILE FOLDER] is selected in the main screen of any of the modes, the file is saved in this folder.
Up to 1000 files can be saved in the Quick File folder. All files in the Quick File Folder can be deleted using the
administrator settings. If you have a file that you do not want deleted, set the file attribute to [PROTECT] (up to 500
files can be protected). (See [Property change] on page 7-21)
The following user and file names are automatically assigned (the names cannot be selected):
User name : User unknown
File name (example) : COPY_04042010_113050AM (job mode and month, day, year, hour, minute, second, AM/
PM of save). (In the example, the file was saved on 4/4/2010 at 11:30 and 50 sec in copy mode.)
When saved, jobs are classified by mode. A saved job can be called up from the COMPLETE job status screen.
■ Main folder
When saving a file, a previously stored user name (see [SYSTEM SETTINGS] on page 7-24) can be specified and
any file name can be assigned.
A password can also be set for a saved file ([CONFIDENTIAL] save). (See [Property change] on page 7-21.)
If a user name and file name are not selected, a name in the same format as Quick File is automatically assigned.
■ Custom folder
Up to 500 folders (named as desired) can be created in this folder. When saving a file in one of these folders, a
previously stored user name (see [SYSTEM SETTINGS] on page 7-24) can be specified and any file name can be
assigned.
A password can be set for a file saved in one of these folders.
■ Attributes of saved files
The protect setting can be selected for files saved with the document filing function. This prevents a file from being
moved or automatically or manually deleted.
Three attributes are available for saved files: [SHARING], [PROTECT], and [CONFIDENTIAL]. When saved with
the [SHARING] attribute, a file is not protected. When saved with the [PROTECT] or [CONFIDENTIAL] attribute, a
file is protected.
Files saved to the Quick File folder are all [SHARING]. When saving a file to the main folder or a custom folder,
[SHARING] or [CONFIDENTIAL] can be selected.
● A [SHARING] file can be changed to a [PROTECT] or [CONFIDENTIAL] file using [Property change] (page 7-21).
● A password is set for a [CONFIDENTIAL] file to protect it. (The password must be entered to call up the file.)
● A password cannot be set for a [PROTECT] file, however, as long as the file is not changed to [SHARING] with
[PROPERTY CHANGE], the file will be protected.
CAUTION
● Documents saved with [QUICK FILE] are shared files that can be called up by anyone and printed or transmitted. For this
reason, do not use Quick File for sensitive documents or documents that you do not want to be reused by others.
● When saving a document with [FILE], set the attribute to [CONFIDENTIAL] and set a password to prevent others from
reusing the document.
● Even when a file is saved with the [CONFIDENTIAL] attribute, the attribute can be changed afterward to [SHARING] using
[Property change] (page 7-21). For this reason, do not save sensitive documents or documents that you do not want to be
reused by others.
● Except in cases provided for by law, SHARP Corporation bears no responsibility for any damages that result from the
leaking of sensitive information due to 1) manipulation by a third party of any data saved using the Quick File function or
filing function, or 2) incorrect operation of the Quick File function or filing function by the operator that saves the data.
7-3
7
dragonII_copy_sec.book
4 ページ
２００６年１０月１８日　水曜日　午後７時３９分
TO USE THE DOCUMENT FILING FUNCTION
A look at the operation panel
DOCUMENT
FILING
IMAGE SEND
PRINT
READY
DATA
LINE
DATA
COPY
SYSTEM
JOB STATUS SETTINGS
1
Touch panel (see the next page)
This displays messages and keys. Keys can be
touched to select and enter settings.
When a key is touched, a beep will sound and the
key will be highlighted to indicate that it is selected.
When a key cannot be selected in a screen, it will
be grayed out. If touched, a warning beep will
sound to alert you that it cannot be selected.
2
4
Numeric keys
Use these keys to enter a password or a numeric
value for a setting.
5
[C] key (Clear key)
Use this key if you make a mistake when entering a
password or numeric setting.
This key is also used to cancel scanning of a
document.
Mode select keys
Use this key to select the mode.
3
LOGOUT
6
Use this key to cancel a setting procedure and
return to the main screen. The key is also used to
cancel a special function.
[DOCUMENT FILING] key
Touch this key to display the main screen of
document filing mode.
[CA] key (Clear all key)
7
[SYSTEM SETTINGS] key
Use this key to store, edit or delete a user name or
custom folder.
Saving files
To save files to the main folder or custom folders, a user name must be previously stored. To create a folder in the
custom folder, the folder name must be stored. These settings are configured in the system settings.
Follow the procedures explained in "Programming a user name", "Editing and deleting a user name", "Creating a
custom folder", and "Editing/deleting a custom folder" on pages 7-25 to 7-28.
7-4
dragon_07-1.fm
5 ページ
２００６年１１月２９日　水曜日　午後９時４０分
TO USE THE DOCUMENT FILING FUNCTION
Main screen of document filing
To display the main screen of document filing, press
the [DOCUMENT FILING] key when the touch panel
shows the copy mode screen, image send mode, or the
job status screen.
The main screen shows messages, keys, and items
that can be selected for document filing.
Document filing icons
Main
icon
Icon of
confidential
file or folder
Icon of
protected
file
Meaning
Folder
Copy job file
FILE STORE
SCAN TO HDD
Print job file
(including direct
print jobs)
FILE RETRIEVE
FILE
FOLDER
QUICK FILE
FOLDER
Fax transmission
job file
SEARCH
GLOBAL ACCESS
HDD STATUS
1
Message display
Displays messages.
2
[SCAN TO HDD] key
Touch to select scan save. Scan save is used to save
the image file of a scanned document in the main
folder or a custom folder without printing or
transmitting the document.
3
4
PC-FAX
transmission job
file
Internet
fax
transmission job
file
PC-Internet fax
transmission job
file
[FILE FOLDER] key
Touch to call up a file from the main folder or the
custom folder. When the key is touched, the files in
the main folder or the folders in the custom folder
appear.
Scan save file
E-mail
transmission job
file
[QUICK FILE FOLDER] key
Touch to call up a file from the Quick File folder.
When the key is touched, the files in the Quick File
folder appear.
5
[SEARCH] key
Touch to search for a file by user name, file name,
or folder name.
6
[HDD STATUS] key
Touch to check the use of the machine's hard disk.
FTP
transmission job
file
Desktop
transmission job
file
Network Folder
transmission job
file
The following icons may appear added to a main icon
or alone.
Icon
Meaning
Confidential file or folder
Protected file
NOTE
When the file of a job that was saved using scan save
is printed in job settings, the icon of the job is
highlighted.
7-5
7
dragonII_copy_sec.book
6 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SAVING A DOCUMENT IMAGE FILE
Quick File
When printing or transmitting a document in copy mode, printer mode, or fax/image transmission mode,"QUICK
FILE" can be selected to save an image of the document to the Quick File folder.
The image can be called up at a later time, allowing you to print or transmit the document without having to locate
the original.
NOTE
As an example, the procedure for saving a document to the Quick File folder while copying using the automatic
document feeding function is explained below.
the original in the document feeder
1 Place
and select resolution and exposure
settings.
AUTO
ORIGINAL
AUTO
EXPOSURE
AUTO 81/2x11
See steps 1 to 8 of
"Making copies with the
automatic
document
feeding function" on
pages 4-7 to 4-8 and
"ADJUSTING
THE
EXPOSURE" on page 414.
the [QUICK FILE] key in the main
2 Touch
screen.
The [QUICK FILE] key
will be highlighted to
FILE
indicate that the function
is selected.
QUICK FILE
If the [FILE] key is
grayed out, only the
[QUICK FILE] key can
be selected.
When you touch the [QUICK FILE] key, a message
asking you to confirm the save will appear. Touch
the [OK] key in the message screen and go to the
next step.
If you wish to cancel the save, touch the [QUICK
FILE] key after touching the [OK] key so that the
[QUICK FILE] key is no longer highlighted.
the [START] key on the operation
3 Press
panel.
To prevent accidental
saving of the document,
the
warning
"THE
SCANNED DATA IS
STORED
IN
THE
QUICK FILE FOLDER."
appears for 6 seconds
after the [START] key is pressed.
When copying begins, the image is saved.
7-6
saved image can be called up from the
4 The
Quick File folder or the job status screen.
●To call the image up from the Quick File folder,
see "Calling up and using a saved file" on
page 7-15.
●To call the job up from the finished job status
screen, see "Calling up and manipulating a
file from the job status screen" on page 7-23.
following operations can be
5 The
performed on the image that was called up
in step 4.
●Print the image (page 7-17)
●Transmit the image (page 7-20)
●Change the attribute (page 7-21)
●Move the image (page 7-22)
●Delete the image (page 7-22)
●Check details on the image (page 7-22)
dragonII_copy_sec.book
7 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SAVING A DOCUMENT IMAGE FILE
Filing
When printing or transmitting a document in copy mode, printer mode, or image send mode, "FILE" can be selected
to save an image of the document to the main folder or a previously created custom folder. The image can be called
up at a later time, allowing you to print or transmit the document without having to locate the original.
NOTE
As an example, the procedure for using the filing function while copying using the automatic document feeding
function is explained below.
the original in the document feeder
1 Place
and select resolution and exposure
settings.
AUTO
ORIGINAL
See steps 1 to 8 of
"Making copies with the
automatic
document
feeding function" on
pages 4-7 to 4-8 and
"ADJUSTING
THE
EXPOSURE" on page 414.
AUTO
EXPOSURE
AUTO 81/2x11
5 Touch the [OK] key.
The touched user name is selected and you return to the
screen of step 3. The selected user name appears.
NOTE
If you do not select a user name, the following name
is automatically selected:
Example : User unknown
6 Touch the [FILE NAME] key.
USER NAME
2
Touch the [FILE] key in the main screen.
FILE NAME
An information
screen appears.
FILE
entry
STORED TO:
A character entry screen
appears. Enter a file
COPY name (maximum of 30
characters). (See page
MAI 7-29
to
enter
characters.)
QUICK FILE
3 Touch the [USER NAME] key.
CONFIDENTIAL
7 Touch the [STORED TO:] key.
USER NAME
FILE NAME
COPY
STORED TO:
MAI
Suzuki
Sasaki
Hasegawa
Nakata
Ono
Yamada
ABCD
EFGHI
7
USER NAME
the desired user name in the list of
4 Touch
user names that appears.
ALL USERS
NOTE
If you do not enter a file name, a file name in the
following format is automatically assigned:
Auto generated file name : Month, day, year, hour,
minute, second, AM/PM
(Example : COPY_04042010_113050AM)
FILE NAME
COPY
STORED TO:
MAIN
1/1
the desired folder name in the list of
8 Touch
folder names that appears
JKLMN
OPQRST
UVWXYZ
User names must be previously stored
("Programming a user name" on page 7-25).
CUSTOM FOLDER 1
CUSTOM FOLDER 2
CUSTOM FOLDER 3
CUSTOM FOLDER 4
CUSTOM FOLDER 5
CUSTOM FOLDER 6
CUSTOM FOLDER 7
CUSTOM FOLDER 8
ALL FOLDERS
ABCD
EFGHI
JKLMN
OPQRS
1/2
UVWXY
Folder names must be previously stored.
("Creating a custom folder" on page 7-27). If a
password has been set for the folder, a password
entry screen will appear. Enter the 5-digit
password for the folder.
7-7
dragonII_copy_sec.book
8 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SAVING A DOCUMENT IMAGE FILE
9 Touch the [OK] key.
FOLDER
will return to the screen of step 4. The
14 You
set password is displayed with " ".
The touched folder is
selected and you return
to the screen of step 5.
The selected folder
name is displayed.
OK
2/2
CANCEL
OK
PASSWORD
XYYY
needed, select the [CONFIDENTIAL]
10 Ifcheckbox
(only in copy mode).
When this is selected, the
file is stored with the
FILE INFORMATION
attribute [CONFIDENTIAL].
CONFIDENTIAL
To call up the file, the
password that will be set in
USER NAME
the following steps must be
entered.
FILE NAME
●If you selected the [CONFIDENTIAL]
checkbox, touch the [PASSWORD] key and
enter a password.
●If you did not select the [CONFIDENTIAL]
checkbox, go to step 16. The file will be saved
as a [SHARING] file.
The password
screen appears.
entry
PASSWORD
XYYY
a 5-digit password with the numeric
12 Enter
keys.
CANCEL
ENTER PASSWORD VIA THE 10-KEY PAD.
13 Touch the [OK] key.
0
CANCEL
10-KEY PAD.
7-8
OK
You will return to the main screen.
the [START] key on the operation
16 Press
panel.
When copying begins,
the image is saved.
saved image can be called up using
17 The
the file name, folder name, or user name,
or from the filing folder.
11 Touch the [PASSWORD] key.
CAN
15 Touch the [OK] key.
As each digit is entered,
"-" changes to " ".
●To call up the image by entering the file name,
folder name, or user name, see "Searching for
and calling up a saved file" on page 7-13.
●To call up the image from the filing folder, see
"Calling up and using a saved file" on page 715.
following operations can be
18 The
performed on the image that was called
up:
●Print the image (page 7-17)
●Transmit the image (page 7-20)
●Change the attribute (page 7-21)
●Move the image (page 7-22)
●Delete the image (page 7-22)
●Check details on the image (page 7-22)
dragon_07-1.fm
9 ページ
２００６年１１月３０日　木曜日　午前９時３４分
SAVING A DOCUMENT IMAGE FILE
Print jobs
Print jobs sent to the machine using the machine's
printer driver can be saved in the main folder or a
previously created custom folder when printed. The
saved print data can be called up and printed or
transmitted without having to open the original file on
your computer.
This section gives an overview of this function and
explains the procedure for printing from the operation
panel of the machine.
For the procedures that are performed at your
computer when initiating printing such as selecting the
save location and file attribute, see the printer driver
Help file.
■ Using a print job file (printing,
deleting, transmitting, etc.)
the [DOCUMENT FILING] key on the
1 Press
operation panel.
DOCUMENT
FILING
PRINT
READY
DATA
the key of the folder that contains
3 Touch
the desired file.
CUSTOM FOLDER 1
CUSTO
CUSTOM FOLDER 3
CUSTO
CUSTOM FOLDER 5
CUSTO
CUSTOM FOLDER 7
CUSTO
ALL FOLDERS
If a password is set for
the selected folder, a
password entry screen
will appear. Enter the 5digit password with the
numeric keys.
MAIN FOLDER
CUSTOM FOLDER
ABCD
EFGHI
JKLMN
OPQRS
the printer icon ( ) tab and then
4 Touch
touch the key of the desired file.
CUSTOM FOLDER
MAIN FOLDER
FILE NAME
SEARCH
USER NAME
DATE
LINE
DATA
COPY
SYSTEM
JOB STATUS SETTINGS
2
Touch the [FILE FOLDER] key or the
[QUICK FILE FOLDER] key depending on
where the file is saved.
FILE RETRIEVE
FILE
FOLDER
QUICK FILE
FOLDER
1
1/1
1
Basic
Yamada
2003/10/01
presentation
Sato
2003/10/01
Product
Akata
2003/10/01
PRINTS
BATCH P.
The following screen appears if the [QUICK FILE
FOLDER] key is touched in step 2.
SEARCH
QUICK FILE FOLDER
IMAGE SEND
BACK
FILE NAME
USER NAME
BACK
DATE
1
1
Tanaka7890123456
User unknown
2003/10/01
Suzuki7890123456
User unknown
2003/10/01
PRINTS
BATCH P.
Touch the key of the file that you wish to call up. A
menu screen will appear.
If a password is set for the file, a password entry
screen will appear. Enter the 5-digit password with
the numeric keys.
the key of the operation that you
5 Touch
wish to perform.
SEARCH
(1)
HDD STATUS
(2)
(3)
CANCEL
JOB SETTINGS
●Touch the [FILE FOLDER] key if the file is
saved in the main folder or the custom folder.
Touch the [QUICK FILE FOLDER] key if the
file is saved in the Quick File folder.
If you touched the [FILE FOLDER] key, the
files in the main folder or the folders in the
custom folder appear. If you open the wrong
folder, touch the [MAIN FOLDER] key or the
[CUSTOM FOLDER] key and open the
correct folder.
●If the desired file is saved in the main folder,
go to step 4. If the desired file is saved in a
custom folder, go to step 3.
●If you touched the [QUICK FILE FOLDER]
key, the files in the Quick File folder appear.
Go to step 4.
Basic specifications
Yamada Taro
1
/
2
8 "x11"
SELECT THE JOB.
PRINT
SEND
PROPERTY
CHANGE
MOVE
DELETE
DETAIL
(4)
(5)
(6)
(1) [PRINT] key (see page 7-17)
(2) [SEND] key (see page 7-20)
(3) [PROPERTY CHANGE] key (see page 7-21)
(4) [MOVE] key (see page 7-22)
(5) [DELETE] key (see page 7-22)
(6) [DETAIL] key (see page 7-22)
The setting screen of the selected operation
appears. See the indicated page.
7-9
7
dragon_07-1.fm
10 ページ
２００６年１１月３０日　木曜日　午前９時０分
SAVING A DOCUMENT IMAGE FILE
Scan Save
Scan save is used to save a scanned document image in the main folder or the custom folder without copying or transmitting it.
the [DOCUMENT FILING] key on the
1 Press
operation panel.
any of the following steps 7 to 16
6 Perform
as needed. When finished, go to step 17 on
page 7-11.
PRINT
READY
DATA
DOCUMENT
FILING
●To set the original size, perform steps 7 to 10.
●To set the resolution, perform steps 11 to 13
on page 7-11.
●To select the exposure, perform steps 14 to 16
on page 7-11.
●If you no not wish to select any of the above
settings, go to step 17 on page 7-11.
LINE
DATA
IMAGE SEND
COPY
SYSTEM
JOB STATUS SETTINGS
2 Touch the [SCAN TO HDD] key.
7 Touch the [ORIGINAL] key.
FILE STORE
SCAN TO HDD
300x300dpi
RESOLUTION
3
AUTO
ORIGINAL
Touch the [SPECIAL MODES] key.
SPECIAL MODES
FILE
INFORMATION
Select
any
special
functions that you wish
to use (otherwise skip
this step).
When the [SPECIAL
MODES] key is touched,
the
special
modes
selection screen appears. (See "Using special
functions for scan save" on page 7-12.)
NOTE
For explanations of the special functions, see page
7-12 and chapter 5.
set the original size, see "Manually
8 To
setting the scanning size" on page 4-5.
the original is two-sided, touch the [29 IfSIDED
BOOKLET] key or the [2-SIDED
TABLET] key depending on where the
pages are bound.
SCAN SIZE
AUTO
2-SIDED
BOOKLET
100%
STORE SIZ
AUTO
2-SIDED
TABLET
4 Touch the [FILE INFORMATION] key.
SPECIAL MODES
10 Touch the [OK] key.
FILE
INFORMATION
You will return to the
screen of step 7.
screens for selecting the user name, file
5 The
name, folder, and attribute appear. Configure the
settings as explained in step 3 to step 15 on
pages 7-7 to 7-8. When step 15 is completed, you
will return to the main screen of document filing.
FILE STORE
FILE RETRIEVE
SCAN TO HDD
FILE
FOLDER
QUICK FILE
FOLDER
SEARCH
GLOBAL ACCESS
7-10
HDD STATUS
STORE SIZE
AUTO
OK
IDED
NOTE
If the original pages are bound at the side, the
document is a "booklet". If the original pages are
bound at the top, the document is a "tablet".
dragonII_copy_sec.book
11 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SAVING A DOCUMENT IMAGE FILE
11 Touch the [RESOLUTION] key.
16 Touch the [OK] key.
You will return to the
screen of step 14.
AUTO
EXPOSURE
OK
300x300dpi
RESOLUTION
MANUAL
AUTO
ORIGINAL
12 Touch the key of the desired resolution.
the original and touch the [START]
17 Place
key.
PRESS [START] TO SCAN ORIGINAL.
SCAN TO HDD
OK
200x200dpi
AUTO
EXPOSURE
300x300dpi
RESOLUTION
400x400dpi
AUTO
ORIGINAL
600x600dpi
HALF TONE
Select one of four resolution levels as appropriate
for the original.
The selected resolution key is highlighted.
13 Touch the [OK] key.
OK
You will return to the
screen of step 11.
NOTE
This completes the scan save procedure. Follow the
steps below when you wish to call up the image and
print or transmit it.
HALF TONE
14 Touch the [EXPOSURE] key.
AUTO
EXPOSURE
AUTO
ORIGINAL
15 Select [AUTO] or [MANUAL].
AUTO
saved image can be called up using
18 The
the file name, folder name, or user name,
or from the filing folder.
300x300dpi
RESOLUTION
AUTO
[Placing the original]
●For information on placing the original, see
"NORMAL COPYING" in chapter 4.
●If you selected the "Card Shot" special function,
the document glass must be used.
●If you selected job build mode, the automatic
document feeding function must be used.
Scanning begins.
If you are using the
document glass, touch
the [READ-END] key
after all pages have
been scanned.
MANUAL
MANUAL
To have the exposure
adjusted automatically,
select [AUTO].
If
you
selected
[MANUAL], touch the
or
key to adjust
the exposure.
(For a darker image, touch
the
key. For a lighter
image, touch the
key.)
●To call up the image by entering the file name,
folder name, or user name, see "Searching for
and calling up a saved file" on page 7-13.
●To call up the image from the filing folder, see
"Calling up and using a saved file" on page 715.
following operations can be
19 The
performed on the image that was called up
in step 18:
●Print the image (page 7-17)
●Transmit the image (page 7-20)
●Change the attribute ((page 7-21)
●Move the image (page 7-22)
●Delete the image (page 7-22)
●Check details on the image (page 7-22)
7-11
7
dragonII_copy_sec.book
12 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SAVING A DOCUMENT IMAGE FILE
■ Using special functions for scan save
Touch the [SPECIAL MODES] key in the main scan save screen to display the special modes screen.
The functions below can be selected in this screen.
READY TO SCAN TO HDD.
PRESS [START] TO SCAN ORIGINAL.
Touch the [SPECIAL MODES]
key in the main screen.
SCAN TO HDD
BACK
AUTO
EXPOSURE
300x300dpi
RESOLUTION
SPECIAL MODES
AUTO
ORIGINAL
FILE
INFORMATION
[READY TO SCAN TO HDD.
PRESS [START] TO SCAN ORIGINAL.
OK
SPECIAL MODES
ERASE
JOB
BUILD
1
[ERASE] key (see page 5-4)
DUAL PAGE
SCAN
[DUAL PAGE SCAN] key (see page 5-5)
(Equivalent to Dual page copy in copy mode)
This function is used to save the opened pages of
a book in order one page at a time (left page then
right page).
3
[2in1] key (see page 5-24)
(When the fax or image send function is installed,
this corresponds to the 2in1 function explained in
the fax and network scanner manuals. This also
corresponds to the "Multishot" function in copy
mode, however, only "2in1" is possible for scan
save. )
This function reduces two original pages and
arranges the images on a single page in a uniform
layout.
7-12
2in1
CARD SHOT
4
Use this function to erase shadows that can appear
around the edges of the image when books and
other thick originals are scanned.
2
1 2
[JOB BUILD] key (see page 5-8)
When you have more pages than can be placed in
the document feeder at once, this function allows
you to scan the pages in sets.
5
[CARD SHOT] key (see page 5-29)
This function allows you to save the front and back
side of a card on a single page (instead of saving
each side as a separate file).
dragon_07-2.fm
13 ページ
２００６年１１月２９日　水曜日　午後１０時６分
CALLING UP AND USING A FILE
Searching for and calling up a saved file
When calling up a file, you can enter the file name, folder name, or user name to quickly search for the file.
To search for a file, touch the [SEARCH] key in the main screen of document filing mode or in a screen that shows
folders or files in a folder. A data search screen will appear.
■ Procedure for searching for a file
the [SEARCH] key in the main
1 Touch
screen of document filing mode or in a
the one-touch key of the user name
4 Touch
that you wish to use to search for the file.
screen that shows folders or files in a
folder.
If you wish to directly enter the user name,
touch the [DIRECT ENTRY] key.
If
you
touch
the
[SEARCH] key in the
screen that shows the
folders in the custom
SEARCH
folder or a screen that
shows the files in a
HDD STATUS
folder, the [SEARCH
WITHIN CURRENT FOLDER] checkbox will
appear. Select this checkbox to search for a file
only in the selected folder.
SEARCH
FILE
FOLDER
Sasaki
Hasegawa
Nakata
Ono
Yamada
ABCD
EFGHI
OK
DIRECT ENTRY
JKLMN
OPQRST
UVWXYZ
●The selected user name is highlighted.
●If you select the wrong user name, touch the
key of the correct name.
●If you touch the [DIRECT ENTRY] key, a
character entry screen will appear. Enter the
user name.
See page 7-29 for the procedure for entering
characters.
OR FOLDER NAME].
CANCEL
Suzuki
ALL USERS
search screen, select whether
2 Inyouthewilldata
search by [USER NAME] or [FILE
SEARCH
CANCEL
SELECT USER NAME.
START SEARCH
5 Touch the [OK] key.
USER NAME
FILE OR FOLDER NAME
CANCEL
●To search by user name, follow steps 3 to 6.
●To search by file name or folder name,
perform step 8.
●To stop searching, touch the [CANCEL]key.
3
CANCEL
SEARCH
7
Touch the [START SEARCH] key.
CANCEL
Touch the [USER NAME] key.
You will return to the
screen of step 2 and the
selected user name will
appear.
DIRECT ENTRY
6
[Searching by user name]
OK
START SEARCH
START SEARCH
USER NAME
FILE OR FOLDER NAME
7-13
dragonII_copy_sec.book
14 ページ
２００６年１０月１８日　水曜日　午後７時３９分
CALLING UP AND USING A FILE
results of the user name search
7 The
appear. Touch the desired file name or
folder name.
name or folder name.
CANCEL
SEARCH
FILE OR FOLDER NAME
USER NAME
SEARCH AGAIN
DATE
CANCEL
SEARCH
FILE OR FOLDER NAME
USER NAME
SEARCH AGAIN
DATE
Product SpecA
AAA
2003/10/20
Product specifications
Yamada
2002/12/30
Product B
AAA
2003/10/20
Products
Sato
2002/12/30
Product 2
AAA
2003/10/20
Product_info
Akata
●See page 7-5 for a list of the document filing
icons.
●When a file name is touched, the operation
selection screen appears. (To perform an
operation using the file, go to step 5 on
page 7-16.)
●When a folder name is touched, all files in the
folder are displayed. Touch the desired file.
(To perform an operation using the file, go
to step 5 on page 7-16.)
●To change the order of file display, touch the
[FILE OR FOLDER NAME] key, [USER
NAME] key, or [DATE] key.
If you touch a file name or folder name that
has a password, a password entry screen will
appear. Enter the 5-digit password with the
numeric keys.
[Searching by file or folder name]
8 Touch the [FILE OR FOLDER NAME] key.
USER NAME
FILE OR FOLDER NAME
A character entry screen
appears. Enter the file
name or folder name to
be used for the search.
See page 7-29 to enter
characters.
9 Touch the [START SEARCH] key.
CANCEL
7-14
results of the file or folder name
10 The
search appear. Touch the desired file
START SEARCH
●See page 7-5 for a list of the document filing
icons.
●When a file name is touched, the operation
selection screen appears. (To perform an
operation using the file, go to step 5 on
page 7-16.)
●When a folder name is touched, all files in the
folder are displayed. Touch the desired file.
(To perform an operation using the file, go
to step 5 on page 7-16.)
●To change the order of file display, touch the
[FILE OR FOLDER NAME] key, [USER
NAME] key, or [DATE] key.
If you touch a file name or folder name that
has a password, a password entry screen will
appear. Enter the 5-digit password with the
numeric keys.
dragon_07-2.fm
15 ページ
２００６年１１月３０日　木曜日　午前９時３９分
CALLING UP AND USING A FILE
Calling up and using a saved file
A file saved with the document filing function can be called up and printed or manipulated as needed.
The following operations can be performed:
● [Print] : Print the file (page 7-17).
● [Send] : Transmit the saved file (page 7-20). The file can be transmitted by Scan to E-mail, Scan to FTP, Scan to
Network Folder, fax, or Internet fax. (All of these methods require installation of the appropriate options.)
(Page 1-12)
● [Property change] : Change the attribute of the saved file (page 7-21).
● [Move] : Move the file (page 7-22).
● [Delete] : Delete the file (page 7-22).
● [Detail] : Show details on the saved file (page 7-22).
■ General procedure for using a saved file
the [DOCUMENT FILING] key on the
1 Press
operation panel.
DOCUMENT
FILING
IMAGE SEND
PRINT
READY
DATA
CUSTOM FOLDER
MAIN FOLDER
SEARCH
CUSTOM FOLDER 1
CUSTOM FOLDER 2
CUSTOM FOLDER 3
CUSTOM FOLDER 4
CUSTOM FOLDER 5
CUSTOM FOLDER 6
BACK
1/1
LINE
DATA
CUSTOM FOLDER 7
COPY
SYSTEM
JOB STATUS SETTINGS
2
the key of the folder that contains
3 Touch
the desired file.
Touch the [FILE FOLDER] key or the
[QUICK FILE FOLDER] key depending on
where the file is saved.
FILE RETRIEVE
FILE
FOLDER
QUICK FILE
FOLDER
SEARCH
ALL FOLDERS
ABCD
CUSTOM FOLDER 8
EFGHI
JKLMN
OPQRST UVWXYZ
If there are more custom folder keys than can
appear in one screen, touch the
or
keys
to change screens.
If a password is set for the selected folder, a
password entry screen will appear. Enter the 5digit password with the numeric keys.
4 Touch the desired file key.
CUSTOM FOLDER
MAIN FOLDER
FILE NAME
USER NAME
SEARCH
DATE
HDD STATUS
●Touch the [FILE FOLDER] key if the file is
saved in the main folder or the custom folder.
Touch the [QUICK FILE FOLDER] key if the
file is saved in the Quick File folder.
If you touched the [FILE FOLDER] key, the
files in the main folder or the folders in the
custom folder appear. If you open the wrong
folder, touch the [MAIN FOLDER] key or the
[CUSTOM FOLDER] key and open the
correct folder.
●If the desired file is saved in the main folder,
go to step 4. If the desired file is saved in a
custom folder, go to step 3.
●If you touched the [QUICK FILE FOLDER]
key, the files in the Quick File folder appear.
Go to step 4.
Basic specifications
Yamada
2003/10/20
presentaion_0903
Sato
2003/10/20
Product_info
Akata
2003/10/20
COPY
BACK
1
1
BATCH P.
Touch the key of the file that you wish to use.
(Parts of the screen that are framed in black are
keys that can be touched.)
A menu screen will appear.
If a password is set for the file, a password entry
screen will appear. Enter the 5-digit password with
the numeric keys.
7-15
7
dragon_07-2.fm
16 ページ
２００６年１０月２２日　日曜日　午後３時２７分
CALLING UP AND USING A FILE
the key of the operation that you
5 Touch
wish to perform.
(1)
(2)
(1) [PRINT] key (see page 7-17)
(2) [SEND] key (see page 7-20)
(3) [PROPERTY CHANGE] key (see page 7-21)
(3)
(4) [MOVE] key (see page 7-22)
CANCEL
JOB SETTINGS
Basic specifications
Yamada Taro
8 1/2"x11"
(5) [DELETE] key (see page 7-22)
SELECT THE JOB.
PRINT
SEND
PROPERTY
CHANGE
MOVE
DELETE
DETAIL
(4)
(5)
(6)
(6) [DETAIL] key (see page 7-22)
The setting screen of the selected operation
appears. See the indicated page.
FILE SELECTION SCREEN
The file selection screen of the Quick File folder, Main folder, and custom folders is explained below.
MAIN FOLDER
CUSTOM FOLDER
FILE NAME
SEARCH
USER NAME
DATE
Basic specifications
Yamada
2006/10/20
Products
Sato
2006/10/20
Product_info
Akata
2006/10/20
ALL FILES
1
File keys
The stored files are displayed. An icon showing
which mode the file was stored from, the file name,
the user name, and the date the file was stored
appear in each file key.
When a file is touched, the job setting screen
appears.
2
7-16
1
3
BATCH P.
3
[Back] key
Touch this key to return to the screen one level up.
4
Select displayed files by job type.
You can select the file keys that are displayed by
job type.
[ALL FILES] is initially selected.
Touch a tab to show a list of the files that were
stored from that mode.
[File Name] key, [User Name] key, [Date] key
Use these keys to change the order of display of
the file keys. When one of the keys is touched,
or
appears in the key.
● When
appears in the [File Name] key or [User
Name] key, the files appear by file name or user
name in ascending order.
When
appears in the [Date] key, the files
appear in order from the oldest date.
● When
appears in the [File Name] key or [User
Name] key, the files appear by file name or user
name in descending order.
When
appears in the [Date] key, the files
appear in order from the most recent date.
BACK
5
[Batch Print] key
Touch this key to print all files in a folder.
For detailed information on batch printing, see 718.
dragonII_copy_sec.book
17 ページ
２００６年１０月１８日　水曜日　午後７時３９分
CALLING UP AND USING A FILE
■ [Print]
A saved file can be printed.
The screen below appears when the [PRINT] key is selected in the operation selection screen. To begin printing,
touch the [PRINT] ( 7 ) key. Printing settings can be selected in this screen before printing. The settings that were
in effect when the file was saved appear initially. The settings can be changed as needed.
NOTES
● When print settings are changed with this procedure, only the value for the number of copies is overwritten.
● The printing speed will be slower for image files saved using certain resolution settings. (See page 7-31.)
CANCEL
JOB SETTINGS / PRINT
Yamada Taro
Basic specifications
81/2 x11
AUTO
PAPER SELECT
NUMBER OF PRINTS
OUTPUT
1
PRINT AND DELETE THE DATA
(1~999)
2-SIDED
PRINT AND SAVE THE DATA
TANDEM PRINT
1
[PAPER SELECT] key
4
If the conditions for tandem printing are met (page
5-10), touch this key to enable tandem printing.
See page 5-10 for more information.
Use this key to set the paper size.
2
[OUTPUT] key
Use this key to select sort, group or staple sort
functions, and to select the output tray.
3
5
[NUMBER OF PRINTS] setting key
Use this key to set the number of copies.
[2-SIDED] key
When performing two-sided printing, use this key to
select the orientation of the image on the back side
of the paper. To have the front and back images
oriented in the same direction, touch the [2-SIDED
BOOKLET] key. To have the front and back images
oriented opposite to each other, touch the [2SIDED TABLET] key. Note that the size and
orientation of the saved image may cause these
keys to have the opposite effect. If neither key is
selected, one-sided printing will take place.
[TANDEM PRINT] key
6
[PRINT AND DELETE THE DATA] key
Touch this key to print a file and then have it
automatically deleted.
7
[PRINT AND SAVE THE DATA] key
Touch this key to print a file. The file will not be
automatically deleted after printing.
7-17
7
dragon_07-2.fm
18 ページ
２００６年１０月２０日　金曜日　午後３時２８分
CALLING UP AND USING A FILE
■ Batch printing
All files in a folder that have the same user name and password can be printed at once.
the [BATCH P.] key in the file list
1 Touch
screen of document filing mode.
has been established, touch
4 Ifthea password
[PASSWORD] key.
To print all files of a
specific type of job,
touch the desired job
tab. The files shown on
that tab can be printed
as a batch.
Enter the password with
USER NAME
Suzuki the numeric keys (5 to 8
digits) and touch the
PASSWORD
[OK] key. Only files that
have
the
same
password
will
be
selected.
If you do not wish to enter a password, go to the
next step.
2006/01/01
2006/01/01
BATCH P.
2 Touch the [USER NAME] key.
set the number of copies, touch the
5 To
[CHANGE PRT.NO.] key.
ALL FILES
USER NAME
CHANGE PRT.NO.
PASSWORD
If you wish to use the
number of copies stored
with each file, go to step
9.
NT AND DELETE THE DATA
the user name of the files that you
3 Touch
wish to print by batch printing.
BATCH PRINT
SELECT USER NAME.
ALL USERS
CANCEL
USER UNKNOWN
Suzuki
Sasaki
Hasegawa
Nakata
Ono
ALL USERS
OK
1
2
Yamada
ABCD
EFGHI
JKLMN
OPQRST
UVWXYZ
NOTE
When [SELECTION OF [ALL USERS] IS NOT
ALLOWED.] checkbox and [SELECTION OF [USER
UNKNOWN] IS NOT ALLOWED.] checkbox are
disabled in the administrator settings, the [ALL
USERS] key and [USER UNKNOWN] key can be
selected.
The [ALL USERS] key can be touched to select all
files in the folder (the files of all users).
The [USER UNKNOWN] key can be touched to
select all files in the folder that do not have a user
name.
7-18
the [APPLY THE NUMBER FROM
6 Touch
STORED SETTING OF EACH JOB]
checkbox to remove the checkmark.
APPLY THE NUMBER FRO
EACH JOB
the number of copies with the
7 Set
keys.
The number of copies
can be also set with the
numeric keys.
R FROM STORED SETTING OF
dragonII_copy_sec.book
19 ページ
２００６年１０月１８日　水曜日　午後７時３９分
CALLING UP AND USING A FILE
8 Touch the [OK] key.
the [PRINT AND DELETE THE
9 Touch
DATA] key or the [PRINT AND SAVE THE
DATA] key.
CANCEL
OK
If the [PRINT AND
DELETE THE DATA] key
PRINT AND DELETE THE DATA
is touched, the files will
PRINT AND SAVE THE DATA
be automatically deleted
after printing.
If the [PRINT AND SAVE
THE DATA] key is
touched, the files will be saved after printing.
If there are no files that match the search
conditions, you will return to the file list screen.
NOTE
● If "Auditing mode" is enabled in the administrator settings for copy mode, print mode, or document filing mode,
it will not be possible to perform batch printing of [ALL FILES].
● To display the job tab of a mode for which "Auditing mode" is enabled in the administrator settings, the account
number must be entered.
7
7-19
dragonII_copy_sec.book
20 ページ
２００６年１０月１８日　水曜日　午後７時３９分
CALLING UP AND USING A FILE
■ [Send]
A saved file can be transmitted by Scan to E-mail, Scan to FTP, Scan to Network Folder, fax, or Internet fax.
These transmission methods require installation of the appropriate options.
The following screen appears when the [SEND] key is touched. Select the destination and other settings required
for transmission and then touch the [SEND] ( 10 ) key to transmit the file. Transmission settings include the
resolution and transmission functions such as a timer setting. Change or select these settings as needed.
NOTE
Jobs that use the following special functions cannot be transmitted when called up. (The [SEND] key is grayed out
in the operation selection screen.)
Pamphlet copying, covers/insert, card shot, Multi shot.
Jobs that use the following functions can be transmitted with certain restrictions when called up:
Card shot:Can be transmitted if saved by scan save or image send.
Multi shot (2in1):Can be transmitted if saved as 2in1 using a portrait original.
[Example of FAX mode]
CANCEL
STANDARD
RESOLUTION
FAX
MODE SWITCH
ADDRESS BOOK
SUB ADDRESS
ADDRESS REVIEW
SPECIAL MODES
Basic specifications
Yamada Taro
SEND
1
[RESOLUTION] key
Use this key to set the resolution.
8
[ADDRESS REVIEW] key
Touch this key to display the destinations.
2
[FILE FORMAT] key
The [FILE FORMAT] key appears in scan mode
(Scan to E-mail, Scan to FTP, or Scan to Network
Folder). Touch this key to set the file format of scan
images that you transmit.
9
3
[FILE NAME/USER NAME] display
This shows the file name and user name of the file
to be transmitted.
4
[
] key (Speed dial key)
Use this key to specify a destination by entering the
3-digit number that is assigned to an e-mail
address or fax number when it is stored in a onetouch key or group key.
5
[MODE SWITCH] key
Use this key to select the transmission mode (Scan
to E-mail, Scan to FTP, Scan to Network Folder,
fax, or Internet fax).
[SPECIAL MODES] key
Touch this key to display the special function menu.
The functions that can be selected vary depending
on the transmission mode:
● Scan to E-mail/FTP/Network Folder
TIMER : The transmission time can be specified.
● FAX
TIMER : The transmission time can be specified.
FAX OWN ADDRESS SENDING: Your sender's
information can be included on the fax pages
printed out by the receiving machine.
● Internet FAX
TIMER : The transmission time can be specified.
I-FAX OWN ADDRESS SEND: Your sender's
information can be included on the Internet fax
pages printed out by the receiving machine.
10
[SEND] key
Touch this key after selecting transmission settings
to begin transmission. (The [START] key can also
be pressed to begin transmission.)
6
[CANCEL] key
Touch this key to return to the operation selection
screen.
7
[ADDRESS BOOK] key
Touch this key to display the destinations stored in
the directory.
7-20
dragonII_copy_sec.book
21 ページ
２００６年１０月１８日　水曜日　午後７時３９分
CALLING UP AND USING A FILE
11
[SEND SETTINGS] key
The [SEND SETTINGS] key is displayed in
scanner mode and in Internet fax mode.
Touch this key to set the subject and file name. In
scanner mode, the sender name can also be set.
12
[SUB ADDRESS] key or [ADDRESS ENTRY] key
● Touch this key to directly enter the destination for
a Scan to E-mail, Scan to FTP, Scan to Network
Folder, or Internet fax transmission.
● Touch this key to enter the sub-address and
passcode for an F-code fax transmission.
NOTE
See the "Operation manual (for facsimile)" and "Operation manual (for image send)" for detailed explanations of
1 , 2 , 3 , 4 , 5 , 6 , 7 , 8 , 9 , 11 , and 12 .
■ [Property change]
Select this operation to change the attribute of a saved file. Three attributes are available: [SHARING],
[PROTECT], and [ CONFIDENTIAL].
The following screen appears when the [PROPERTY CHANGE] key is selected in the operation selection screen.
Note the restrictions below on changing the attribute.
CANCEL
JOB SETTINGS / PROPERTY CHANGE
Basic specifications
Yamada Taro
[Restrictions on changing the attribute]
●A file that is set to [SHARING] can be
changed to [PROTECT] or [CONFIDENTIAL].
However, a [SHARING] file that is saved in the
Quick File folder can only be changed to
[PROTECT].
●A file that is set to [PROTECT] can be
changed to [SHARING] or [CONFIDENTIAL].
However, a [PROTECT] file that is saved in
the Quick File folder can only be changed to
[SHARING].
●A file that is saved in the Quick File folder
cannot be changed to [CONFIDENTIAL].
OK
81/2 x11
SHARING
PROTECT
CONFIDENTIAL
PASSWORD
the [PROPERTY CHANGE] key in
1 Touch
the operation selection screen.
3 Touch the [OK] key.
PROPERTY
CHANGE
NCEL
7
OK
DETAIL
2 Touch the key of the desired attribute.
SHARING
CONFIDENTIAL
If you are changing a
[SHARING]
or
[PROTECT]
file
to
[CONFIDENTIAL],
touch the [PASSWORD]
key and enter the
password.
PROTECT
PASSWORD
7-21
dragonII_copy_sec.book
22 ページ
２００６年１０月１８日　水曜日　午後７時３９分
CALLING UP AND USING A FILE
■ [Move]
■ [Delete]
This operation is used to move a file to a different
folder.
The following screen appears when the [MOVE]
key is selected.
Only [SHARING] and [CONFIDENTIAL] files can
be moved. A [PROTECT] file can be moved by first
using [PROPERTY CHANGE] to change the
attribute to [SHARING] or [CONFIDENTIAL].
CANCEL
JOB SETTINGS / MOVE
Basic specifications
Yamada Taro
■ [Detail]
1/2 x11
8A4
SELECT THE FOLDER THE FILE IS MOVED TO.
FILE NAME
Basic specifications
MOVE TO:
MOVE
the [MOVE TO:] key and select the
1 Touch
folder to which you wish to move the file.
●Select the main folder or a folder in the
custom folder. A file cannot be moved to the
Quick File folder.
●The file name can be changed when moving a
file. To change the name, touch the [FILE
NAME] key and enter the desired file name.
See page 7-29 for the procedure for entering
characters.
2 Touch the [OK] key.
N FOLDER
OK
3 Touch the [MOVE] key.
amada Taro
A4
OVED TO.
ations
MOVE
4 Touch the [CANCEL] key.
CANCEL
aro
1/ x11
8A4
2
7-22
This operation is used to delete the selected file.
Touch the [DELETE] key in the operation select
screen. A message asking you to confirm the
deletion will appear. Touch the [YES] key to delete
the file.
Only [SHARING] or [CONFIDENTIAL] files can be
deleted. (A [PROTECT] file can be deleted by first
using [PROPERTY CHANGE] to change the
attribute to [SHARING].)
You will return to the
operation
selection
screen.
This operation is used to show detailed information
on the selected file.
Touch the [DETAIL] key to display the information.
The information appears on two screens. Touch the
key or
key to move between the two
screens.
The file name can be changed in the information
screen. To change the name, touch the [FILE
NAME] key and enter the desired file name in the
character entry screen that appears. See page 729 for the procedure for entering characters.
dragonII_copy_sec.book
23 ページ
２００６年１０月１８日　水曜日　午後７時３９分
CALLING UP AND USING A FILE
■ Calling up and manipulating a file from the job status screen
Files saved using the "FILE" and "QUICK FILE" functions appear as keys in the finished job status screen.
You can view information on a file that appears in this screen and manipulate the file.
Press the [JOB STATUS] key.
1
AGE SEND
DATA
view information on the file, touch the
4 To
[DETAIL] key.
The job status screen
appears.
COPY
Use the
keys
to change screens.
When you are finished,
touch the [OK] key to
return to the screen of
step 3.
DETAIL
SYSTEM
JOB STATUS SETTINGS
CALL
X JOB
2 Touch the [COMPLETE] key.
1/8
DETAIL OF
COPY
The finished job screen
appears.
JOB QUEUE
INTERNET FAX
FILE NAME:
OK
COPY_20031021_153050
CALL
RESOLUTION:600x600dpi
SIZE:81/2 x11
1/2
COMPLETE
DATE:2003/10/10 15:30
PAGES:10
DETAIL
DETAIL OF
COPY
FILE NAME
3
Touch the key of the desired file.
OK
COPY_20031021_153050
DATA SIZE: 21,987,543KB
SPECIAL
MODES:
If there are more keys
than can appear in one
screen and the desired
COPY
14:38 12/09 00
file does not appear,
Suzuki7890123456 14:09 12/09 00
touch the
key or
key to change
COPY
13:27 12/09 00
screens.
The touched key is highlighted.
JOBS COMPLETED
SET TIME
CALL
DOCUMENT
STYLE:
1-SIDED
2/2
OUTPUT:
FILE FORMAT:
NUM
Tanaka7890123456 14:38 12/09 01
5 Touch the [CALL] key.
The operation selection
screen appears.
CALL
X JOB
7
INTERNET-FAX
Select and perform the desired operation as
explained in "Calling up and using a saved file"
(page 7-15).
7-23
dragonII_copy_sec.book
24 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SYSTEM SETTINGS
Creating, editing, and deleting user names and folders
This section explains how to create, edit, and delete user names and custom folders for saving files with the
document filing function. User names and custom folders are created and edited at the operation panel of the
machine or in the Web page.
NOTES
● A previously stored name cannot be used when creating a new user name or custom folder. However, the same password
can be used more than once.
● A password cannot be omitted when creating a user name.
■ General procedure for creating, editing, and deleting user names and folders
Follow steps 1 to 3 below to create, edit, or delete a user name or custom folder. In step 3, select the key for the
specific operation that you wish to perform.
1 Press the [SYSTEM SETTINGS] key.
LINE
DATA
AGE SEND
the key of the operation that you
3 Touch
wish to perform.
Go to the page indicated below for the selected
operation.
COPY
SYSTEM
JOB STATUS SETTINGS
(1)
(2)
SYSTEM SETTINGS
OK
DOCUMENT FILING CONTROL
2
Touch the [DOCUMENT FILING CONTROL]
key.
TOTAL COUNT
DEFAULT
SETTINGS
ADDRESS CONTROL
SENDER CONTROL
DOCUMENT FILING
CONTROL
ADMINISTRATOR
USER NAME REGISTRATION
AMEND/DELETE USER NAME
CUSTOM FOLDER REGISTRATION
AMEND/DELETE CUSTOM FOLDER
(3)
(4)
(1) [USER NAME REGISTRATION] key
Program a user name. (See the next page)
(2) [AMEND/DELETE USER NAME] key
Edit or delete a user name. (See page 7-26)
(3) [CUSTOM FOLDER REGISTRATION] key
Create a custom folder. (See page 7-27)
(4) [AMEND/DELETE CUSTOM FOLDER] key
Edit or delete a custom folder. (See page 7-28)
7-24
dragonII_copy_sec.book
25 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SYSTEM SETTINGS
■ Programming a user name
To program a user name, follow steps 1 and 2 on page 7-24, touch the [USER NAME REGISTRATION] key in
step 3, and then follow these steps:
1 Touch the [USER NAME] key.
The lowest number that
has not yet been
USER NAME
programmed
appears
PASSWORD
automatically in "No.".
Touch the number to
SELECT THE DEFAULT FOLDER THE F
STORED TO:
display a character entry
screen and enter a user
name (maximum of 16 characters). See page 7-29
for the procedure for entering characters.
SYSTEM SETTINGS
you wish to specify a folder for the user
6 Ifname,
touch the [STORED TO:] key. If you
wish to use the main folder, go to step 8.
No.001
2
Touch the [INITIAL] key.
A character entry screen
appears. Enter up to 10
search characters. See
page 7-29 for the
procedure for entering
characters.
NEXT
INITIAL
R THE FILE WITH THIS USER NAME IS STORED.
No.001 REGISTRATION IS COMPLETED.
USER NAME
PASSWORD
SELECT THE DEFAULT FOLDER THE FILE
STORED TO:
MAIN FOLDER
folders that have been created appear.
7 The
Touch the desired folder. If you wish to
create a new folder, or if no folders have
been created, touch the [ADD NEW] key.
STORED TO:
MAIN FOLDER
CUSTOM FOLDER 1
CUSTOM FOLDER 2
CUSTOM FOLDER 3
CUSTOM FOLDER 4
CUSTOM FOLDER 5
CUSTOM FOLDER 6
CUSTOM FOLDER 7
CUSTOM FOLDER 8
ALL FOLDERS
3
Yamada
ABCD
EFGHI
JKLMN
OPQRS
ADD NEW
1/1
UVWXY
Touch the [PASSWORD] key.
SYSTEM SETTINGS
A password cannot be
omitted.
No.001
Yamada
USER NAME
If you touched the [ADD NEW] key, program a
name for the folder as explained on page 7-27.
The user name programmed in step 1 is selected
as the user name of the folder.
PASSWORD
SELECT THE DEFAULT FOLDER THE FIL
STORED TO:
8 Touch the [EXIT] key.
a password for the user name (enter a
4 Set
5-digit password with the numeric keys).
This will be the password
for the user name
entered in step 1.
ENTER PASSWORD VIA THE 10-KEY PAD.
As each digit is entered,
"-" changes to " ". If
you make a mistake,
press the [C] key and
then enter the correct number.
You will return to the
"USER
NAME
REGISTRATION"
screen.
"REGISTRATION
IS
COMPLETED."
will
appear highlighted next
to "No.".
EXIT
– – – – –
CANCEL
5
exit, touch the [EXIT] key. To program
9 To
another user name, touch the [NEXT] key.
Touch the [OK] key.
NEXT
INITIAL
Yamada
EXIT
WITH THIS USER NAME IS STORED.
CANCEL
10-KEY PAD.
OK
EXIT
If you touched the [EXIT]
key, you will return to the
screen of step 3 on page
7-24. If you touched the
[NEXT] key, a new user
entry screen will appear.
Repeat steps 1 to 9 to
program a new user.
7-25
7
dragonII_copy_sec.book
26 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SYSTEM SETTINGS
■ Editing and deleting a user name
To edit or delete a user name, follow steps 1 and 2 on page 7-24 and then follow these steps:
the [AMEND/DELETE USER NAME]
1 Touch
key.
OK
[Editing]
the key of each item that you wish to
4 Touch
edit (edit as explained in steps 1 to 9 in
"Programming a user name" on page 725).
AMEND/DELETE USER NAME
AMEND/DELETE CUSTOM FOLDER
USER NAME / AMEND/DELETE
No.001 REGISTRATION IS COMPLETED.
Yamada
USER NAME
the [USER NAME] key that you wish
2 Touch
to edit or delete.
INIT
PASSWORD
SELECT THE DEFAULT FOLDER THE FILE WITH
STORED TO:
MAIN FOLDER
When you have finished
editing
the
items,
"REGISTRATION
IS
COMPLETED."
will
appear highlighted next
to "NO.".
EXIT
USER NAME / AMEND/DELETE
SELECT USER NAME TO AMEND/DELETE.
Suzuki
Sasaki
Hasegawa
Nakata
Ono
Yamada
ALL USERS
ABCD
EFGHI
1/1
you have finished editing
5 When
desired items, touch the [EXIT] key.
JKLMN
OPQRST
UVWXYZ
DELETE
EXIT
A password entry screen will appear.
ITIAL
3
the
To edit another user
name, repeat steps 2 to
4.
To exit, touch the [EXIT]
key in the screen of step
2.
Yamada
Enter the 5-digit password with the
numeric keys.
THIS USER NAME IS STORED
ENTER PASSWORD VIA THE 10-KEY PAD.
NOTE
When a user name is changed, the change is not
updated to any previously saved data (files or
folders).
CANCEL
BCD
EFGHI
JKLMN
OPQRST UVWXYZ
After entering the password, the following screen
will appear.
DELETE
USER NAME / AMEND/DELETE
EXIT
No.001
USER NAME
Yamada
INITIAL
[Deleting]
6 Touch the [DELETE] key.
Yamada
DELETE
EXIT
PASSWORD
SELECT THE DEFAULT FOLDER THE FILE WITH THIS USER NAME IS STORED.
STORED TO:
MAIN FOLDER
● To edit a user name, perform steps 4 and 5.
● To delete a user name, perform steps 6 and 7.
ITIAL
Yamada
H THIS USER NAME IS STORED
7 Touch the [YES] key.
DELETE THE USER NAME?
Yamada
NO
7-26
YES
You will return to the
screen of step 2. To
delete another user
name, repeat steps 2, 3,
5 and 6.
To exit, touch the [EXIT]
key in the screen of step
2.
dragonII_copy_sec.book
27 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SYSTEM SETTINGS
■ Creating a custom folder
Up to 500 custom folders can be created. When no further folders can be created, delete unneeded folders (page
7-28) and then create a new folder. A password can be omitted when creating a folder. To create a custom folder,
follow steps 1 and 2 on page 7-24, touch the [CUSTOM FOLDER REGISTRATION] key in step 3, and then follow
the steps below.
1 Touch the [FOLDER NAME] key.
The lowest number that
has not yet been
FOLDER NAME
programmed
appears
INITIAL
automatically in "No.".
Touch the number to
USER NAME
display a character entry
screen and enter a folder
name (maximum of 28 characters). See page 7-29
for the procedure for entering characters.
5 Touch the [OK] key.
CUSTOM FOLDER REGISTRATION
No.001
2
EXIT
10-KEY PAD.
6 Touch the [USER NAME] key.
No.001
Touch the [INITIAL] key.
CUSTOM FOLDER REGISTRATION
No.001
FOLDER NAME
USER FOLDER 1
INITIAL
P
USER NAME
OK
CANCEL
FOLDER NAME
A character entry screen
appears. Enter up to 10
search characters. See
page 7-29 for the
procedure for entering
characters.
INITIAL
USER FOLDER 1
USER1
PAS
USER NAME
You will select a user
name that will be
associated with the
folder name you are
programming.
Selection of a user name
cannot be omitted.
programmed user names appear.
7 The
Touch the desired user name. If you do not
wish to use any of the user names that
appear, touch the [ADD NEW] key to
program a new user name.
you wish to set a password for the new
3 Iffolder,
touch the [PASSWORD] key.
A password can be
omitted.
If you are omitting a
password, go to step 6.
CUSTOM FOLDER REGISTRATION
No.001
FOLDER NAME
INITIAL
USER FOLDER 1
PASSWORD
CUSTOM FOLDER REGISTRATION
USER NAME
Suzuki
Sasaki
Hasegawa
Nakata
Ono
Yamada
ALL FOLDERS
4
ABCD
EFGHI
1/1
7
ADD NEW
JKLMN
OPQRST
UVWXYZ
When you touch a user name, a password entry
screen appears.
If you touched the [ADD NEW] key, program a user
name as explained on page 7-25. The folder name
programmed in step 1 will be selected as the folder
for the user.
Set a password for the folder (enter a 5digit password with the numeric keys).
CANCEL
OK
SELECT USER NAME.
This will be the password
for the folder name
entered in step 1.
ENTER PASSWORD VIA THE 10-KEY PAD.
the 5-digit password of the selected
8 Enter
user name with the numeric keys.
ENTER PASSWORD VIA THE 10-KEY PAD.
CANCEL
BCD
EFGHI
JKLMN
OPQRST UVWXYZ
7-27
dragonII_copy_sec.book
28 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SYSTEM SETTINGS
9 Touch the [OK] key.
exit, touch the [EXIT] key. To create
10 To
another folder, touch the [NEXT] key.
If you touched the [EXIT]
key, you will return to the
screen of step 3 on page
7-24. If you touched the
[NEXT] key, a new folder
screen
will
appear.
Repeat steps 1 to 10 to
OK
ADD NEW
JKLMN
OPQRST
EXIT
NEXT
1/1
SWORD
UVWXYZ
create a new folder.
■ Editing/deleting a custom folder
To edit a previously created folder (change the folder name, initial, password, or user name), or to delete a folder,
follow steps 1 and 2 on page 7-24 and then follow the steps below.
When deleting a folder...
A folder that contains files cannot be deleted. Either move the files to a different folder or delete them before deleting the folder.
: [MOVE] (see page 7-22)
: [DELETE] (see page 7-22)
the [AMEND/DELETE
1 Touch
FOLDER] key.
CUSTOM
[Editing]
Touch the key of each item that you wish to
edit (edit as explained in steps 1 to 10 of
"Creating a custom folder" on page 7-27).
4
AMEND/DELETE USER NAME
DELETE
CUSTOM FOLDER / AMEND/DELETE
AMEND/DELETE CUSTOM FOLDER
EXIT
No.001 REGISTRATION IS COMPLETED.
USER FOLDER 1
FOLDER NAME
2
Touch the [FOLDER NAME] key that you
wish to edit or delete.
SELECT CUSTOM FOLDER TO AMEND/DELETE.
CUSTOM FOLDER 1
CUSTOM FOLDER 2
CUSTOM FOLDER 3
CUSTOM FOLDER 4
CUSTOM FOLDER 5
CUSTOM FOLDER 6
CUSTOM FOLDER 7
ALL FOLDERS
ABCD
1/2
CUSTOM FOLDER 8
EFGHI
JKLMN
OPQRST
UVWXYZ
If a password has been set for the folder, a
password entry screen will appear. Enter the
correct 5-digit password with the numeric keys.
USER NAME
Yamada
PASSWORD
you have finished editing the items,
5 When
touch the [EXIT] key.
To edit another folder, repeat steps 2 to 5.
[Deleting]
Touch the [DELETE] key.
6
3 Edit or delete the folder.
DELETE
CUSTOM FOLDER / AMEND/DELETE
USER1
After editing the items and returning to the screen of
step 3, "REGISTRATION IS COMPLETED." will be
highlighted to the right of "No.".
To stop using a password, touch the
[PASSWORD] key and then touch the [OK] key
without entering anything for the password. [-] will
appear and the password will be canceled.
EXIT
CUSTOM FOLDER / AMEND/DELETE
INITIAL
EXIT
No.001
DELETE
FOLDER NAME
EXIT
USER FOLDER 1
INITIAL
USER1
USER NAME
Yamada
PASSWORD
*****
●To edit the folder, perform steps 4 and 5.
●To delete the folder, perform steps 6 and 7.
●To exit, touch the [EXIT] key.
ORD
– – – – –
7 Touch the [YES] key.
DELETE THE FOLDER?
USER FOLDER 1
NO
7-28
YES
You will return to the
screen of step 2.
To delete another folder,
repeat steps 2, 6, and 7.
To exit, touch the [EXIT]
key in the screen of step
2.
dragonII_copy_sec.book
29 ページ
２００６年１０月１８日　水曜日　午後７時３９分
ENTERING CHARACTERS
To enter or edit characters in setting screens such as auto dial key programming screens, follow the steps below.
Characters that can be entered are alphabetical characters, special characters, numbers, and symbols.
■ Entering alphabetical characters
(Example: Sharp äÄ)
1 Touch the [S] key.
5 Touch the [
Characters cannot be
entered beyond the " " mark.
ÃÄÂ/ãäâ] key.
Sharp
6 Touch the [ä] key.
To switch between upper case and lower case,
touch the [ABC
abc] key. When ABC is
highlighted, upper case letters are entered.
2 Touch the [ABC
Sharp
abc] key.
S
To switch between upper case and lower case,
touch the [ÃÄÂ
ãäâ] key. When ãäâ is
highlighted, lower case letters are entered.
7 Touch the [ÃÄÂ
ãäâ] key.
Sharp ä
3
Touch the [h] key, [a] key, [r] key, and [p]
key.
Shar
8 Touch the [Ä] key.
7
Sharp ä
If you make a mistake, touch the
key to move
the cursor ( ) back one space and then enter the
correct character. You can also press the [AB/ab
12#$%] key during entry to enter a number or
symbol.
4
Touch the [SPACE] key.
Sharp
You can press the [ABC/abc] key during entry to
return to alphabetical character entry. You can
also enter numbers and symbols.
9 When finished, touch the [OK] key.
Sharp äÄ
The cursor ( ) moves forward and a space is
entered.
You will exit the character entry screen and return
to the programming screen. If you touch the
[CANCEL] key, you will return to the programming
screen without storing the entered characters.
7-29
dragon_07-3.fm
30 ページ
２００７年２月１６日　金曜日　午後１時３３分
ENTERING CHARACTERS
■ Entering numbers and symbols
1 Touch the [AB/ab
12#$%] key.
you have finished
3 When
characters, touch the [OK] key.
entering
1&1
When the characters "12#$%" are highlighted,
number/symbol entry mode is selected.
the desired number or symbol.
2 Enter
Numbers and symbols that can be entered are as
follows:
Screen 1/2
Screen 2/2
Change screens by touching the
key or
key
displayed in the screen. If you make a mistake,
touch the
key to move the cursor ( ) back one
space and then enter the correct character.
You can continue touching keys to enter
characters. You can also touch another character
type selection key ([ ÃÄÂ/ãäâ] key or [AB/ab
12#$%] key) to enter characters other than
numbers and symbols.
7-30
You will exit the character entry screen and return
to the programming screen. If you touch the
[CANCEL] key, you will return to the programming
screen without storing the entered characters.
NOTE
The following symbols cannot be used when
entering a file name or folder name.
\
?
/
"
;
:
,
<
>
!
*
|
&
#
Depending on the environment of use of the OS, it
may not be possible to use spaces and the symbols
indicated below.
For example, hyperlinks will not operate correctly or
nonsense characters may appear.
$ % ' ( ) + - . = @ [ ] ^ ` { } _
dragonII_copy_sec.book
31 ページ
２００６年１０月１８日　水曜日　午後７時３９分
TROUBLESHOOTING
This section explains problems frequently encountered when using the document filing function. If you experience
any difficulty, refer to the following table. For information on general machine problems, printer problems, fax
problems, and network scanner problems, please see the troubleshooting sections of the appropriate manuals.
Problem
Check
Cause and solution
A saved file has
disappeared.
Was the file called up and then printed by
touching the [PRINT AND DELETE THE
DATA] key?
A file that is printed using the [PRINT AND
DELETE THE DATA] key is automatically
deleted after being printed. To print a file
without deleting it, use the [PRINT AND
SAVE THE DATA] key.
A file cannot be
deleted.
Is the file's attribute set to [PROTECT]?
A file cannot be deleted when its attribute is
set to [PROTECT]. Change the attribute to
[SHARING] and then delete the file.
A file's attribute
cannot be set to
[CONFIDENTIAL].
Is the file in the main or custom folder?
A file in the Quick File folder cannot be set to
[CONFIDENTIAL]. Move the file to a
different folder or set it to [PROTECT].
A file's attribute
cannot be changed
to [PROTECT].
Is the file set to [CONFIDENTIAL]?
A file cannot be simultaneously set to
[CONFIDENTIAL] and [PROTECT]. If set to
[CONFIDENTIAL],
use
[PROPERTY
CHANGE] (page 7-21) to change the
attribute to [PROTECT].
A name in the Quick
File folder is cut off.
Was the name programmed in the advanced
transmission settings?
If the name was programmed in the
advanced transmission settings before the
file was saved in the Quick File folder, that
name will be used. However, if the name is
longer than the maximum name length of the
Quick File folder (30 characters), the excess
characters will be discarded.
Resolution settings
are not possible.
Was the file saved at low resolution?
A saved file cannot be transmitted at a
resolution higher than the resolution at
which it was saved.
A file name cannot
be
stored
or
changed.
Have you entered prohibited characters in
the file name?
Certain characters (symbols) cannot be
used in file names. See "ENTERING
CHARACTERS" (entering numbers and
symbols) on page 7-29.
A custom folder
name cannot be
stored or changed.
Have you entered prohibited characters in
the folder name?
Certain characters (symbols) cannot be
used in folder names. See "ENTERING
CHARACTERS" (entering numbers and
symbols) on page 7-29.
The printing speed
of a saved file is
slow.
The file was saved using one of the following
resolution settings:
● 200 x 200 dpi resolution.
● STANDARD (200 x 100 dpi) or FINE (200
x 200 dpi)
When a file is saved using one of the
resolutions setting at left, the printing speed
will be slower than when other resolution
settings are used.
Black dots appear
when a file that was
saved
with
the
document
filing
function is printed.
Was the file saved at other than the following
resolutions?
● 600x600dpi
● 600x600dpi and HALF TONE
To check the resolution of the saved file,
touch the [DETAIL] key in step 5 on page 716.
This problem can be alleviated by setting the
resolution to 600x600dpi when saving a file
with scan save. The problem can be further
alleviated by selecting HALF TONE after
setting the resolution to 600x600dpi, as light
images will be printed lightly.
7-31
7
dragonII_copy_sec.book
32 ページ
２００６年１０月１８日　水曜日　午後７時３９分
dragonII_copy_sec.book
1 ページ
２００６年１０月１８日　水曜日　午後７時３９分
CHAPTER 8
SPECIFICATIONS
This chapter contains useful information about the machine.
Page
SPECIFICATIONS................................................................................... 8-2
INDEX ..................................................................................................... 8-4
8-1
dragon_08.fm
2 ページ
２００６年１１月２９日　水曜日　午後９時１１分
SPECIFICATIONS
Type
Console
Print system
Electrophotographic system
Exposure system
OPC
Developer system
Dry-type two-component magnetic brush development
Paper feed system
4 trays and bypass tray
Fusing system
Heater roller
Resolution
Scan: 600 x 600 dpi, output: 600 x 600 dpi
Gradation
256 levels
Originals
Sheets, bound documents
Maximum size: 11" x 17" or A3
Copy paper
Plain paper and special papers
Copy sizes
Max. 11" x 17" or A3, min. 5-1/2" x 8-1/2"R or A5R, Postcard
Image loss: Max 21/64" or 8 mm (leading edge and trailing edge in total),
max. 21/64" or 8 mm (along all other edges in total)
Warm-up time
120 seconds or less
First-copy time
MX-M550U/MX-M620U/MX-M550N/MX-M620N
4.0 seconds or less*
MX-M700U/MX-M700N
3.5 seconds or less*
* When 8-1/2" x 11" (A4) size paper is fed horizontally from tray1
Copy ratio
Variable: 25 to 400% in 1% increments, total 376 steps
Fixed presets: 25%, 64%, 77%, 100%, 121%, 129%, 200% and 400% for inch
system, 25%, 50%, 70%, 81%, 86%, 100%, 115%, 122%, 141%, 200% and
400% for AB system.
Continuous copy
999 copies
Dimensions
(including automatic
document feeder)
28-43/64" (W) x 26-47/64" (D) x 46-15/16" (H)
(728 mm (W) x 679 mm (D) x 1192 mm (H))
Weight (main unit only)
Approx. 408 lbs. (Approx. 185 kg)
Overall dimensions
(When tray is extended)
49-23/32" (W) x 26-47/64"(D) (1263 mm (W) x 679 mm (D))
Required power supply
USA: AC120V, 60Hz, 16A
Power consumption
1.8 kW
Operating conditions
Temperature: 50ºF to 86ºF (10ºC to 30ºC)
Humidity: 20% to 85%
Automatic document feeder
Type
Two-side simultaneous scanning system
Original size
11" x 17" to 5-1/2" x 8-1/2" (A3 to A5)
Capacity
Maximum of 150 sheets (20 lbs. (80 g/m2)) or total stack height of 49/64" (19.5
mm) or less.
Original exchange speed
One-sided: 65 pages/min.
Two-sided: 76 sides/min.
Power supply
Supplied from machine
Some discrepancies may exist in the illustrations and content due to improvements to the machine.
8-2
dragonII_copy_sec.book
3 ページ
２００６年１０月１８日　水曜日　午後７時３９分
SPECIFICATIONS
Continuous copying speed (when the offset function is not used)
MX-M550U/MX-M550N
Copy paper size
MX-M620U/MX-M620N
MX-M700U/MX-M700N
100% / Reduced / Enlarged
11" x 17" (A3)
30 copies/min.
34 copies/min.
39 copies/min.
8-1/2" x 14" (B4)
35 copies/min.
39 copies/min.
45 copies/min.
8-1/2" x 11" (A4)
55 copies/min.
62 copies/min.
70 copies/min.
8-1/2" x 11"R (A4R)
40 copies/min.
45 copies/min.
48 copies/min.
7-1/4" x 10-1/2" (B5)
55 copies/min.
62 copies/min.
70 copies/min.
7-1/4" x 10-1/2"R (B5R)
40 copies/min.
45 copies/min.
48 copies/min.
8-1/2" x 5-1/2"R (A5R)
40 copies/min.
45 copies/min.
48 copies/min.
Center tray specifications
Output method
Face-down output
Maximum number
of sheets
(20lbs.
(80g/m2)
/recommended
paper)
250 sheets*
Paper type
Plain paper and special paper
* The maximum number of pages that can be held varies
depending on ambient conditions in the installation
location, the type of paper, and the storage conditions of
the paper.
Acoustic Noise Emission (measurement according to ISO7779)
Printing mode
Standby mode
7.3B
5.0B
Bystander positions
58dB(A)
34dB(A)
Operator position
58dB(A)
35dB(A)
Sound power level LwA
Sound pressure level LpA
(reference)
* Noise emission when peripheral devices are installed
Emission Concentration (measurement according to RAL-UZ62: Edition Jan. 2002)
Ozone
0.02 mg/m3 or less
Dust
0.075 mg/m3 or less
Styrene
0.07 mg/m3 or less
8
8-3
dragon_08.fm
4 ページ
２００６年１０月２２日　日曜日　午後７時４０分
INDEX
[ ] key................................................................. 1-13
[#/P] key ............................................................... 1-13
■ Numerics
1-sided copy .................................................. 4-7, 4-11
1-sided copy-Automatic document feeder .............. 4-7
1-sided copy-Document glass .............................. 4-11
256MB expansion memory board ........................ 1-12
2in1 ............................................................. 5-24, 7-12
2-sided copy ......................................... 1-3, 4-10, 4-13
■ A
Acceptable originals ............................................... 4-2
Account number ................................................... 1-18
Additional fax memory.......................................... 1-12
Address control .................................................... 2-18
Adjusting the exposure.................................. 1-3, 4-14
Administrator settings........................................... 2-18
Alarm display........................................................ 3-16
All custom setting list............................................ 2-20
Application communication module............. 1-12, 3-19
Application integration module ............................. 1-12
Attributes ................................................................ 7-3
Auditing mode ...................................................... 1-18
Auto image ........................................................... 4-15
Auto power shut-off mode ...................................... 1-9
Automatic copy image rotation ............................... 4-4
Automatic document feeder ................. 1-10, 2-31, 4-2
Automatic document feeder .........................................
-1-sided copies.................................................... 4-7
-Acceptable originals........................................... 4-2
-Automatic two-sided copying ........................... 4-10
-Misfeed original................................................ 2-31
-Setting originals ................................................. 4-3
-User maintenance.............................................. 6-2
Automatic exposure adjustment ........................... 4-14
Automatic selection .............................................. 4-15
Automatic two-sided copying
-Automatic document feeder ............................. 4-10
-Document glass ............................................... 4-13
Automatic two-sided printing ................................ 2-13
Auxiliary tray......................................................... 2-10
■ B
B/W reverse............................................ 1-6, 5-2, 5-31
Barcode font kit .................................................... 1-12
Binding change .................................................... 4-13
Book copy .............................................. 1-5, 5-2, 5-26
Book original .......................................................... 5-5
Bypass tray......................................... 1-10, 2-28, 4-20
■ C
[C] key ........................................................... 1-13, 7-4
[CA] key......................................................... 1-13, 7-4
Call for service ..................................................... 2-32
[CALL] key............................................................ 1-16
Calling up and using a file .................................... 7-13
8-4
Calling up and using a saved file.......................... 7-15
-Delete............................................................... 7-22
-Detail................................................................ 7-22
-Move ................................................................ 7-22
-Print.................................................................. 7-17
-Property change .............................................. 7-21
-Send................................................................. 7-20
-Card shot ..................................1-6, 5-2, 5-29, 7-12
Centre erase........................................................... 5-4
Centre tray..................................................... 1-10, 4-9
[CENTRE TRAY] key.............................................. 3-6
Changing the paper size in paper tray ......... 2-3 to 2-6
Clear all key................................................... 1-13, 7-4
Clear key ....................................................... 1-13, 7-4
Clock .................................................................... 2-18
Confidential ............................................................ 7-3
Contents ....................................................... 0-5 to 0-6
Continuous copying speed ..................................... 8-3
[COPY] key........................................................... 1-13
Cover of the duplex unit........................................ 1-11
Covers/inserts ........................................1-5, 5-2, 5-12
Creating a custom folder ...................................... 7-27
Custom folder ...........................7-3, 7-24, 7-27 to 7-28
■ D
Data security kit.................................................... 1-12
Default settings..................................................... 2-20
[DETAIL] key......................................................... 1-16
Display contrast.................................................... 2-20
Display switching keys.......................................... 1-16
Disposal of hole punch scrap ............................... 3-10
Document feeder tray ...................................... 4-2, 4-3
Document filing control......................................... 2-18
Document filing function .................................. 1-8, 7-1
Document filing user / folder list ........................... 2-20
[DOCUMENT FILING] key ............................ 1-13, 7-4
Document glass
-1-sided copies.................................................. 4-11
-Automatic two-sided copying ........................... 4-13
-Placing originals................................................. 4-3
-User maintenance.............................................. 6-2
Document transfer cover ............................... 2-31, 4-3
Dual page copy ........................................1-4, 5-2, 5-5
DUAL PAGE SCAN .............................................. 7-12
Duplex unit ........................................................... 1-11
■ E
Editing and deleting
-Custom folder................................................... 7-28
-User names...................................................... 7-26
Energy saving features........................................... 1-9
Energy Star guidelines ........................................... 1-9
Enlargement ......................................................... 4-15
Entering characters .................................. 7-29 to 7-30
Erase ...............................................1-4, 5-2, 5-4, 7-12
dragon_08.fm
5 ページ
２００６年１０月２３日　月曜日　午後１２時２分
INDEX
Examples of covers and inserts ............... 5-17 to 5-22
-Covers.................................................. 5-18 to 5-21
-Inserts .............................................................. 5-22
External account module............................. 1-12, 3-20
■ F
Facsimile expansion kit ........................................ 1-12
Fax data receive/forward ...................................... 2-18
[FAX JOB] key ...................................................... 1-16
Features ................................................................. 1-3
[FILE FOLDER] key................................................ 7-5
Finisher ......................................................... 1-10, 3-2
[FINISHER TRAY] key............................................ 3-6
Front cover .................................................... 1-10, 3-2
Fusing unit.......................................... 1-11, 2-23, 2-24
■ G
General procedure for using special functions ....... 5-2
Grayed out............................................................ 1-14
Group ....................................................... 1-3, 3-4, 4-9
[GROUP] key.......................................................... 3-6
■ H
[HDD STATUS] key................................................. 7-5
Heavy paper ................................................ 2-12, 2-13
Highlighted ........................................................... 1-14
Hole punching ................................................. 1-8, 3-5
■ I
Icon ...................................................... 1-14, 5-17, 7-5
[IMAGE SEND] key .............................................. 1-13
Information ........................................................... 2-23
Inserter................................................. 1-8, 1-10, 3-14
Installation requirements ........................................ 0-2
Interior .................................................................. 1-11
Internet fax expansion kit ..................................... 1-12
[INTERNET-FAX] key ........................................... 1-16
Interrupting a copy run .................................. 1-7, 5-46
■ J
Job build ..........................................1-5, 5-2, 5-8, 7-12
Job programs .................................... 1-6, 5-44 to 5-45
-Calling up ......................................................... 5-45
-Deleting............................................................ 5-45
-Storing ............................................................. 5-44
Job status screen ................................................. 1-15
[JOB STATUS] key ............................................... 1-13
■ K
Keyboard select.................................................... 2-20
■ L
Labels................................................................... 2-12
Landscape.............................................................. 1-2
Large capacity tray (AR-LC6)............... 1-10, 2-7, 2-29
Large capacity tray (AR-LC7)............... 1-10, 2-8, 2-30
Left cover of paper drawer ................................... 1-11
Left side cover release ......................................... 1-11
List print................................................................ 2-20
Loading paper ........................................................ 2-2
-bypass tray ....................................................... 2-10
-tray 1 - tray 2 ...................................................... 2-2
-tray 3 .................................................................. 2-5
-tray 5 ........................................................ 2-7 to 2-9
LOGOUT .............................................................. 1-13
[LOGOUT] key............................................. 1-13, 1-18
Lower cover ............................................................ 3-2
■ M
Main features................................................ 1-3 to 1-8
Main folder.............................................................. 7-3
Main power switch ....................................... 1-11, 1-17
Main screen............................................................ 5-2
Manual exposure adjustment ............................... 4-14
Manual selection .................................................. 4-16
Margin Shift ..............................................1-4, 5-2, 5-3
Meaning of "R" ....................................................... 1-2
Mirror image ...........................................1-6, 5-2, 5-31
Misfeed...................... 2-23 to 2-31, 3-11 to 3-12, 3-18
Misfeed in the paper feed area................. 2-26 to 2-30
Misfeed original .................................................... 2-31
Misfeed removal ................................................... 2-23
-Tray 1 - tray 2 ................................................... 2-26
-Tray 3 - tray 4 ................................................... 2-27
-Automatic document feeder ............................. 2-31
-Bypass tray ...................................................... 2-28
-Finisher/saddle stitch finisher........................... 3-11
-Inserter............................................................. 3-17
-Transport area, fusing area, and exit area ....... 2-24
-Tray 5 ................................................... 2-29 to 2-30
-Duplex unit ....................................................... 2-25
Mode select key ................................................... 1-15
Mode select keys........................................... 1-13, 7-4
More information on plain paper........................... 2-13
More information on special media ...................... 2-13
Multi shot ................................................1-5, 5-3, 5-24
■ N
Network expansion kit .......................................... 1-12
Network scanner expansion kit ............................ 1-12
Non-standard sizes .....................2-12, 2-14, 2-17, 4-5
Number of pages printed...................................... 1-18
number of pages transmitted (scanned)............... 1-18
Numeric keys................................................. 1-13, 7-4
■ O
Offset............................................................... 1-7, 3-4
[OFFSET] key......................................................... 3-6
Operation panel........................................... 1-10, 1-13
-Document filing function..................................... 7-4
-Inserter............................................................. 3-15
Original guides ....................................................... 4-3
Original orientation .......................................... 3-5, 4-4
Original size .............................................4-2, 4-5, 4-6
Output .............................................3-4, 3-6, 4-9, 4-12
Output tray..................................................... 1-10, 4-9
8-5
8
dragon_08.fm
6 ページ
２００６年１２月１日　金曜日　午前８時５３分
INDEX
■ P
Pamphlet copy.......................................... 1-4, 5-2, 5-6
Paper curled ......................................................... 2-33
Paper tray settings ...................................... 2-14, 2-20
Part names
-Exterior ............................................................ 1-10
-Finisher and the saddle stitch finisher................ 3-2
-Inserter............................................................. 3-14
-Interior.............................................................. 1-11
-Operation panel ............................... 1-13, 3-15, 7-4
-Trays................................................................... 2-2
Password................................................................ 7-8
Peripheral devices ....................................... 1-10, 1-12
Photo.................................................................... 4-14
Photoconductive drum ......................................... 1-11
Placing originals ..................................................... 4-3
Plain paper ............................................... 2-12 to 2-13
Portrait.................................................................... 1-2
Postcards ........................................ 2-10 to 2-11, 4-20
Power .......................................................... 1-17, 2-32
Power switch ............................................... 1-11, 1-17
Preheat mode......................................................... 1-9
Preset copy ratios................................................. 4-16
[PRINT JOB] key .................................................. 1-16
PRINT mode indicators ........................................ 1-13
Printer condition ................................................... 2-18
Printer test page................................................... 2-20
[PRIORITY] key.................................................... 1-16
Proper storage ..................................................... 2-22
Protect.................................................................... 7-3
PS3 expansion kit ................................................ 1-12
Punch module ............................................... 1-11, 3-2
[PUNCH] key ................................................. 3-6, 3-15
■ Q
Quick File folder ..................................................... 7-3
[QUICK FILE FOLDER] key ................................... 7-5
■ R
[READ-END] key ................................. 4-12, 5-8 to 5-9
Reduction ............................................................. 4-15
Reduction/Enlargement................................. 1-4, 4-15
Replacing the toner cartridges ............................. 2-21
Right side cover.................................................... 1-11
Rotation copying .................................................... 4-4
■ S
Saddle stitch.................................................... 1-8, 3-5
Saddle stitch finisher ..................................... 1-10, 3-2
Saddle stitch tray.................................................... 3-2
[SADDLE STITCH] key .......................................... 3-6
Saving a document image file .................... 7-6 to 7-12
-Filing ........................................................ 7-7 to 7-8
-Print jobs ............................................................ 7-9
-Quick file ............................................................ 7-6
-Scan save ............................................ 7-10 to 7-11
[SCAN TO] key ..................................................... 1-15
[SCAN TO HDD] key .............................................. 7-5
[SEARCH] key........................................................ 7-5
Searching for a file ................................... 7-13 to 7-14
8-6
Selecting a function .............................................. 1-14
Selecting the exposure level................................. 4-14
Selecting the exposure mode............................... 4-14
Selecting the output tray......................................... 4-9
Sender control ...................................................... 2-18
Sender control list ................................................ 2-20
Sending address list ............................................. 2-20
Setting the paper size............................... 2-14 to 2-17
Setting the paper type .............................. 2-14 to 2-16
Sharing................................................................... 7-3
Sharp OSA ........................................................... 3-19
Sort...........................................................1-3, 3-4, 4-9
[SORT] key ............................................................. 3-6
Special modes (Copier operation).......................... 5-2
Special modes (Document filing function) ............ 7-12
Special paper ........................................... 2-12 to 2-13
Special papers ..................................................... 4-20
Specifications ............................................... 8-2 to 8-3
-Finisher/saddle stitch finisher................... 3-2 to 3-3
-Inserter............................................................. 3-14
-Large capacity tray (AR-LC6)............................. 2-7
-Large capacity tray (AR-LC7)............................. 2-8
-Punch module .................................................... 3-3
Specifications of paper trays ................................ 2-12
Standard sizes............................................... 1-2, 2-13
Standard sizes in both the inch and AB systems ... 1-2
Staple cartridge ...................................................... 3-3
Staple cartridge replacement ....................... 3-7 to 3-8
Staple jam removal..................................... 3-9 to 3-10
Staple sort ....................................................... 1-7, 3-4
[STAPLE SORT] key............................................... 3-6
[STAPLE] key ....................................................... 3-15
Stapler compiler ..................................................... 3-2
Stapling positions ................................................... 3-4
[START] key................................................. 1-13, 3-15
[STOP/DELETE] key ............................................ 1-16
Storage of supplies............................................... 2-22
System settings ........................................... 2-18, 7-24
[SYSTEM SETTINGS] key ............................ 1-13, 7-4
■ T
Tab copy .................................................1-6, 5-2, 5-26
Tabbed paper....... 2-6, 2-10, 2-12 to 2-13, 3-15, 4-20, 5-12, 5-27
Tandem copy ..........................................1-5, 5-2, 5-10
Text....................................................................... 4-14
Text/photo............................................................. 4-14
The machine does not operate...................... 2-32, 6-3
Toner cartridge ............................................ 1-11, 2-21
Top cover ................................................................ 3-2
Total count ............................................................ 2-20
Total number of originals ........................................ 4-2
Touch panel ...................................1-13, 1-14, 7-4, 7-5
Transparency film .............. 2-6, 2-12, 2-13, 4-20, 5-23
Transparency inserts ..............................1-5, 5-2, 5-23
Tray................................................................ 1-10, 3-2
Tray 1..........................................1-10, 2-2 to 2-4, 2-26
Tray 2..........................................1-10, 2-2 to 2-4, 2-26
Tray 3....................................................1-10, 2-5, 2-27
Tray 4....................................................1-10, 2-6, 2-27
Tray 5................................... 1-10, 2-7, 2-8, 2-29, 2-30
dragon_08.fm
7 ページ
２００６年１０月１９日　木曜日　午後１時４分
INDEX
Troubleshooting
-Copier operation ................................................ 6-3
-Document filing function................................... 7-31
-Finisher/saddle stitch finisher........................... 3-13
-General information ............................. 2-32 to 2-34
-Inserter............................................................. 3-18
Types and sizes of paper ......................... 2-12 to 2-13
Types and sizes of paper that can be used .......... 2-12
■ U
Upper cover of large capacity tray........................ 1-11
User maintenance .................................................. 6-2
User name................................................ 7-24 to 7-26
■ W
Warming up .......................................................... 2-32
■ X
XY Zoom ....................................................... 1-4, 4-18
■ Z
Zoom .................................................................... 4-16
8
8-7
dragonII_copy_sec.book
10 ページ
２００６年１０月１８日　水曜日　午後７時３９分
dragonII_copy_sec.book
1 ページ
２００６年１０月１８日　水曜日　午後７時３９分
NOTICE
BE SURE TO ASK YOUR AUTHORIZED SHARP DEALER ABOUT THE WAR-RANTY THAT YOUR
SELLING DEALER EXTENDS TO YOU. In order to assure you, the end-user, of warranty protection,
Sharp extends a limited warranty to each of its authorized dealers and, in turn, requires each of its
authorized dealers to extend its own warranty to you on terms that are no less favorable than those
given to the dealer by Sharp. You should be aware, however, that Sharp does not itself extend any
warranties, either express or implied, directly to you, the end-user and no one is authorized to make
any representations or warranties on behalf of Sharp. Specifically, SHARP DOES NOT EXTEND TO
YOU, THE END-USER, ANY EXPRESS WARRANTY OR ANY IMPLIED WARRANTY OF
MERCHANTABILITY, FITNESS FOR USE OR FITNESS FOR ANY PARTICULAR PURPOSE IN
CONNECTION WITH THE HARDWARE, SOFTWARE OR FIRMWARE EMBODIED IN, OR USED
IN CONJUNCTION WITH THIS PRODUCT. Sharp is not responsible for any damages or loss, either
direct, incidental or consequential, which you, the end-user, may experience as a result of your
purchase or use of the hardware, software or firmware embodied in or used in conjunction with this
Product. Your sole remedy, in the event that you encounter any difficulties with this Product, is
against the authorized dealer from which you purchased the Product. In the event that this
authorized dealer does not honor its warranty commitments, please contact the General Manager,
Business Products Group, Sharp Electronics Corporation, Sharp Plaza, Mahwah, NJ 07430-1163,
so that Sharp can try to help assure complete satisfaction of all the warranty rights to which you are
entitled from the authorized dealer.
In the event that this authorized dealer does not honor its warranty commitments, please contact the
General Manager, Business Products Group, Sharp Electronics Corporation, Sharp Plaza, Mahwah,
NJ 07430-1163, so that Sharp can try to help assure complete satisfaction of all the warranty rights
to which you are entitled from the authorized dealer.
cover4.fm
1 ページ
２００７年２月１６日　金曜日　午後１２時５５分
MX-M550U/MX-M620U/MX-M700U/MX-M550N/MX-M620N/MX-M700N
OPERATION MANUAL (for general information and copier operation)
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-1163.
www.sharpusa.com
SHARP ELECTRONICS OF CANADA LTD.
335 Britannia Road East, Mississauga, Ontario, L4Z 1W9
This manual has been printed using a vegetable-based soy oil ink
to help protect the environment.
Printed on 100% post-consumer recycled paper
PRINTED IN CHINA
2007C
KS1
TINSE3584FCZ1