EBA 485 A, 485 EP Paper Guillotine Operating Instructions
广告
广告
Guillotines
EBA 485 A
EBA 485 EP
GB Operating Instructions
• Safety precautions •
EBA 485 A • EBA 485 EP
D Bitte lesen Sie vor Inbetriebnahme der Maschine unbedingt diese Betriebsanleitung und beachten Sie die Sicherheitshinweise. Die Betriebsanleitung muss jederzeit verfügbar sein.
GB Please read these operating instructions before putting the machine into operation and observe the safety precautions. The operating instructions must always be available.
F Nous vous prions de lire attentivement le mode d’emploi avant d’utiliser la machine, et attirons votre attention sur les consignes de sécurité. Les instructions d'utilisation et les consignes de sécurité doivent toujours être disponibles. Les instructions d'utilisation et les consi.
NL Leest u voor de ingebruik name van het apparaat a.u.b. deze gebruiksaanwijzing goed door en neemt u de veiligheidsinstructies n acht. De gebruiksaanwijzing en de veiligheids-voorschriften moeten altijd binnen handbereik zijn.
I Per favore legga questo manuale di istruzione prima di mettere in funzione il distruggidocumenti e osservi le regole di sicurezza. Le istruzioni d’uso devono essere sempre disponibili.
E Le recomendamos lea las instrucciones antes de poner en funcionamiento esta máquina y cumpla las normas de seguridad. Las instrucciones de servicio y seguridad deben estar siempre disponibles.
S Läs igenom denna bruksanvisning innan ni startar maskinen. Var noga med säkerhetsföreskrifterna. Instruktionsmanualen måste alltid finnas tillgänglig.
FIN Lue nämä käyttö-ohjeet läpi ennenkuin käynnistät laitteen !
Noudata turvaohjeita. Käyttöohjeiden on oltava aina saatavilla.
N Lees gjennom denne bruksannvisningen før De tar i bruk maskinen
Vær oppmerksom på sikkerhetsforskriftene. Opperatørmanualen må alltid være tilgjengelig.
PL Proszę uważnie przeczytać instrukcję obsługi przed uruchomieniem urządzenia i stosować się do przepisów bezpieczeństwa. Instrukcje obsługi muszą być zawsze dostępne.
RUS Ïîæàëóéñòà, ïðî÷èòàéòå èíñòðóêöèþ ïî ýêñïëóàòàöèè ïåðåä óñòàíîâêîé
àïïàðàòà, ñîáëþäàéòå òåõíèêó áåçîïàñíîñòè. Èíñòðóêöèÿ ïî
ýêñïëóàòàöèè äîëæíà íàõîäèòüñÿ â äîñòóïíîì äëÿ ïîëüçîâàòåëÿ ìåñòå.
H A gép üzembe helyezése elott figyelmesen olvassa el a kezelési utasítást és tartsa be a biztonsági eloírásokat.Kezelési utasításnak mindig elérhetonek kell lennie.
TR Lütfen makineyi çalýþtýrmadan önce bu kullanma talimatlarýný dikkatli bir þekilde okuyunuz ve belirtilen güvenlik önlemlerine uyunuz. Kullanma Talimatlarý her zaman kullanýma hazýr olmalýdýr.
DK Før installation af maskinen bedes De venligst læse brugervejledningen brugervejledningen og være opmærksom på sikkerhedsanvisningerne.
Brugervejledningen skal altid være tilgængelig.
CZ Prosím přečtěte si instrukce k obsluze a dodržujte bezpečnostní upozornění. Návod k obsluze musí být vždy dostupný.
P Por favor leiam o manual de instruções antes de colocar a máquina em operação e vejam as precauções de segurança. As instruções de operação deverão estar sempre disponíveis.
GR ÐÁÑÁÊÁËÙ ÄÉÁÂÁÓÔÅ ÔÉÓ ÏÄÇÃÉÅÓ ×ÑÇÓÅÙÓ ÊÁÉ ÔÉÓ ÐÑÏÖÕËÁÎÅÉÓ
ÁÓÖÁËÅÉÁÓ ÐÑÉÍ ÂÁËÅÔÅ ÔÏ ÌÇ×ÁÍÇÌÁ ÓÅ ËÅÉÔÏÕÑÃÉÁ.
ÏÉ ÏÄÇÃÉÅÓ ×ÑÇÓÇÓ ÐÑÅÐÅÉ ÍÁ ÅÉÍÁÉ ÐÁÍÔÁ ÄÉÁÈÅÓÉÌÅÓ.
SLO Prosimo preberite navodila za uporabo ter upoštevajte varnostna opozorila preden zaženete naparavo. Navodila naj bodo vedno pri roki.
SK Starostlivo si preštudujte tento návod na obsluhu pred uvedením stroja do prevádzky a najmä bezpecnostné predpisy. Držte tento návod na obsluhu na dostupnom mieste.
EST Palun lugege enne masina käivitamist käesolevat kasutusjuhendit ning järgige ohutusnõudeid. Kasutusjuhend peab alati käepärast olema.
CHI
UAE
- 2-
• Safety precautions •
D Keine Bedienung durch Kinder!
GB Children must not operate the machine!
F Pas d‘utilisation par un enfant!
NL Geen bediening door kinderen!
I Non lasciare utilizzare il tagliacarte a bambini!
E No dejar que la utilicen los niños!
S Installera maskinen utom räckhåll för barn!
FIN Asentakaa laite lasten ulottumattomiin !
N Installer maskinen utenfor rekkevidde for barn!
PL Dzieciom nie wolno obsługiwać urządzenia !
RUS Íå äîïóñêàéòå äåòåé ê ïîëüçîâàíèþ àïïàðàòîì!
H Gyerekek a gépet nem kezelhetik
TR Makinayý Çocuklar Kullanmamalýdýr.
DK Må kun betjenes af voksne
CZ Stroj nesmí být obsluhován dětmi!
P As crianças não devem trabalhar com a máquina!
GR ÁÐÁÃÏÑÅÕÅÔÁÉ Ç ×ÑÇÓÇ ÁÐÏ ÐÁÉÄÉÁ.
SLO Otroci ne smejo uporabljati naprave
SK So strojom nesmú pracovat deti!
EST Lapsed ei tohi masinat kasutada!
CHI
UAE
D Nicht unter das Messer fassen!
GB Do not reach beneath the blade!
F Ne pas passer les mains sous la lame!
NL Niet met de handen onder het mes komen!
I Non toccare la lama nella parte inferiore!
E ¡No tocar debajo de la cuchilla!
S Sträck inte in handen under kniven!
FIN Älä laita kättäsi terän alle !
N Plasser aldri hender ol. under kniven !
PL Nie wkładać rąk pod noże!
RUS Èçáåãàéòå ïîïàäàíèÿ ðóê ïîä ëåçâèå!
H Ne nyúljon a kés alá!
TR Elinizi býçaðýn altýna sokmayýnýz!
DK Stik ikke hænderne ind under knivbladet!
CZ Nesahejte pod ostří nože!
P Não tocar na parte inferior da faca!
GR ÌÇÍ ÁÃÃÉÆÅÔÅ ÔÏ ÊÁÔÙ ÌÅÑÏÓ ÔÇÓ ËÅÐÉÄÁÓ!
SLO Ne segajte z roko pod rezilo!
SK Nevkladajte ruky pod nôž!
EST Ärge pange kätt tera alla!
CHI
UAE
- 3 -
• Safety precautions •
EBA 485 A • EBA 485 EP
D Messer nie lose liegen lassen!
Messer nur mit Messerwechselvorrichtung oder im
Messertransportkasten befördern!
(siehe Seite 31 und 33).
Warnung! Verletzungsgefahr!
GB Never leave the blade unattended!
Do not extract or transport the blade without protection!
(See page 31 and 33).
Danger! Risk of injury!
F Ne jamais laisser la lame sans protections !
Elle ne doit être démontée qu’à l’ aide du dispositif de changement de lame (cf. page 31 et 33), ou transportée dans son étui en bois !
Danger! Risques de coupures !
NL Laat nooit de messen alleen achter.
Transporteer de messen niet zonder de houten bescherming
(zie pagina 31 en 33).
Waarschuwing! Opgelet voor ongevallen!
I Non lasciare mai la lama incustodita. Non rimuovere o trasportare la lama senza protezione. (Vedi pagina 31 e 33).
Attenzione! Rischio di infortunio!
E ¡No quitar la cuchilla sin prestar atención. No desmontar no transportar la cuchilla sin protección! (vérase pág. 31 y 33)
¡Advertencia! ¡Peligro de hacerse daño!
S Lämna aldrig maskinen obemannad. Ta inte ur eller transportera kniven utan skydd. (se sid 31 och 33).
Skaderisk!
FIN Käsittele terää aina varoen. Älä siirrä tai kuljeta terää ilman suojaa ! (katso sivu 31 ja 33
Loukkaantumisen vaara !
N La aldri kniven ligge ubeskyttet. Ta aldri ut kniven eller transporter den uten beskyttelse (Se side 31 og 33)
FARE ! Muligheter for skade !
PL Nigdy nie pozostawiać noży bez nadzoru.
Nie wyciągać lub transportować noży bez osłon!
(zobacz strona 31 i 33).
Ryzyko skaleczenia sie!
RUS Íå îñòàâëÿéòå îòêðûòîå ëåçâèå áåç ïðèñìîòðà! Íå
ïûòàéòåñü èçâëå÷ü èëè òðàíñïîðòèðîâàòü ëåçâèå áåç
ñïåöèàëüíûõ ìåð ïðåäîñòîðîæíîñòè!
(Ñì. ñòðàíèöû 31 è 33)
Ñîáëþäàéòå âûøå ïåðå÷èñëåííûå ïðàâèëà Ñîáëþäàéòå âûøå ïåðå÷èñëåííûå ïðàâèëà
äëÿ èçáåæàíèÿ òðàâì!
H Soha ne hagyja a kést őrizetlenül!
Ne vegye ki vagy ne szállítsa a kést védőtok nélkül!
(Lásd 31. és 33. oldal)
Veszély! Sérülésveszély!
TR Býçaðý hiçbir zaman gözetimsiz býrakmayýnýz!
Býçaðý muhafazasýz olarak yerinden çýkartmayýnýz veya taþýmayýnýz! (Sayfa 31 ve 33’e bakýnýz)
Dikkat! Yaralanma riski!
- 4 -
• Safety precautions •
DK Knivbladet må aldrig efterlades uden opsyn.
Forsøg ikke at afmontere eller transportere knivbladet uden beskyttelse! (Se side 31 og 33)
FARE! Risiko for legemlig beskadigelse.
CZ Nikdy nenechávejte nůž bez krytu.
Nikdy nevyjímejte nebo neprepravujte nuz bez ochranného krytu (viz. strany 31 a 33)
Nebezpecí! Riskujete zranení
P Deixar a faca sempre em local seguro!
Não retirar ou transportar a faca sem protecção!
(Ver pág. 31 e 33)
Perigo! Risco de dano!
GR ÌÇÍ ÁÖÇÍÅÔÅ ÔÇÍ ËÅÐÉÄÁ ÁÍÅÐÉÔÇÑÇÔÇ!
ÌÇÍ ÁËËÁÆÅÔÅ ¹ ÌÅÔÁÖÅÑÅÔÅ ÔÇÍ ËÅÐÉÄÁ ×ÙÑÉÓ
ÐÑÏÖÕËÁÎÇ (Äåßôå ó÷åôéêÜ óôéò óåëßäåò 31&35)
ÐÑÏÓÏ×Ç ! ÊÉÍÄÕÍÏÓ ÔÑÁÕÌÁÔÉÓÌÏÕ !
SLO Nikoli ne puščajte rezila nazaščitenega. Nikoli ne prenašajte rezilo brez zaščite. ( glej stran 31 in 33).
Pozor!
SK Nenechávajte nôž nechránený (nezabezpecený)!
Nevyberajte alebo netransportujte nôž bez ochrany
(vid s. 31 a 33)
! Riziko úrazu !
EST Ärge jätke lõiketera kunagi järelevalveta!
Ärge pikendage ega teisaldage tera kaitseseadmeteta!
(Vt lk 31 ja 33)
Oht! Vigastuste oht!
CHI
31 33
UAE
33 31
- 5 -
• Safety precautions •
EBA 485 A • EBA 485 EP
D Keine harten und splitternden Materialien schneiden!
GB Do not cut hard materials or materials which may splinter!
F La coupe de matériaux trop durs ou risquant des projections est interdite !
NL Snij geen harde materialen of materiaal dat kan splinteren!
I Utilizzare il tagliacarte esclusivamente per il taglio di risme di carta o materiali analoghi!
E ¡No cortar materiales duros o materiales que puedan astillarse!
S Förstör inte hârt material eller material som kan splittras!
FIN Asentakaa laite lasten ulottumattomiin !
N Ikke kutt hardt metall eller materiale som kan splintre !
PL Nie ciąć twardych materiałów lub materiałów, które mogą ulec odpryśnięciu!
RUS Äàííûé ðåçàê íå ïðåäíàçíà÷åí äëÿ ðåçêè òâåðäûõ
ìàòåðèàëîâ èëè ìàòåðèàëîâ, êîòîðûå ìîãóò
ðàñùåïëÿòüñÿ!
H Ne vágjon kemény vagy olyan anyagot, amely repedhet!
TR Sert veya parçalanabilecek malzemeleri kesmeyiniz!
DK Der må ikke skæres i hårde materialer eller i materialer, der kan splintre!
CZ Neřežte tvrdý materiál, při kterém mohou ustřelovat ostré
úlomky!
P Não cortar materiais duros ou materiais que possam lascar!
GR ÌÇÍ ÊÏÂÅÔÅ ÓÊËÇÑÁ ÕËÉÊÁ ¹ ÕËÉÊÁ ÐÏÕ
ÈÑÕÌÌÁÔÉÆÏÍÔÁÉ!
SLO Nikoli ne režite trdih materialov ali materialov, ki se lahko razcepijo.
SK Nerežte tvrdé materiály, alebo materiály, z ktorých môžu vystrelovat ostré úlomky.
EST Ärge lõigake kõvasid materjale ega materjale, mis võivad pilbasteks puruneda!
CHI
UAE
- 6 -
• Safety precautions •
The machine is designed for cutting stacks of paper to a specified size.
This machine is constructed for "one-man operation" only!
Warning! Clips or similar damage the cutting blade.
Disconnect from the mains before starting any service work or before removing the panels!
Replacement of blade and cutting stick may be performed only when the main switch is switched off!
- 7 -
EBA 485 A • EBA 485 EP
A
• Safety precautions •
All components which could endanger the operator are covered by a guard!
A
A
B
C
A
C
- 8 -
Operating the machine without safety device is forbidden!
(Front safety guard (A), rear screwed safety guard (B) and panel (C).
• Safety precautions •
The dangerous cutting movement is safeguarded by a movable guard (A) and a safety two-handed control system! (B)
B
A
A
Before working with the machine and after every blade replacement the automatic cut-off function of safety guard (A) (correct if distance between cover and table is < 20 mm), main switch (B) and control panel (C) must be checked.
C
20mm
0.79inch
B
- 9 -
EBA 485 A • EBA 485 EP
• Safety precautions •
Protect mains cable against heat, oil and sharp edges!
230V / 10A min
115V / 15A min
Connect the power cord to a single phase socket.
Ensure free access to mains!
- 10 -
• Safety precautions •
When not in use for a longer period switch off.
(Main switch to "0").
Clamping
OK
Blade
Danger!
Blade must always be covered by the pressing bar.
OK
- 11 -
EBA 485 A • EBA 485 EP
• Installation •
Remove the stand from the wooden pallet.
B
4 x
A
C
- 12 -
4 strong people are required to lift the machine from the pallet and place it on the stand.
Secure with 4 screws (A). Put the shelf (B) on the stand. (Parts and tools are in the tool set
(C).
• Installation •
Only EBA 485 A
Tighten the backgauge crank (A). Parts and tools are in the tool set (C).
C
A
Plug into socket.
The machine must be connected directly to the socket.
- 13 -
EBA 485 A • EBA 485 EP
A
A
A
• Operation •
It is forbidden to operate the machine if the operating and safety instructions have not been understood. Please check the safety devices are functioning and complete before use.
• All covers have to be mounted (A).
• The release for cutting is allowed only if the cover is closed and the two-hand safety device is operated at the same time (B)
• If the front cover closes by itself the gas spring (X) needs replacing.
We recommend you keep a record of your test results.
B
B
X
- 14 -
• Operation •
C A
D
Position the main switch to "I" (A). Insert the key for the control system and move it to the right (B). Open the safety guard (C). The machine is now ready for use.
Only EBA 485 EP
Press S button (D).
Machine will automatically go to the start position.
B
B
EBA 485 EP
The measurement is set either with the handwheel (A) or by programming (B) the cutting measurements. Measurement is shown on the display in inches or cm (B).
A
- 15 -
EBA 485 A • EBA 485 EP
C
D
E
A
B
• Operation •
EBA 485 A
The measurement is set with the backgauge crank.(A) The symbol – rotary direction –
moves to the right on the display (B) (see picture C). The rotary direction of the backgauge crank (A) is indicated on the right.
Keep turning the backgauge crank to the right until a measurement appears (see picture E).
The reference position is reached.
The cutting size can now be set with the handle (A).
If the backgauge is right at the front the symbol – rotary direction – will move to the left (see picture D). Turn the backgauge crank to the left until the rotary direction appears on the right in the display (see picture C).
Afterwards turn the backgauge crank to the right until a measurements appears (see picture E). The reference position is reached.
The cutting size can now be set with the handle (A). Proceed to position from the rear.
Measurement is shown on the display in inches or cm (B).
A
B
Optical cutting line (A) that indicates the exact position of the cut. Blade cuts on the front edge (B) of the light beam. (Only use when no exact cut is required).
- 16 -
• Operation •
Only EBA 485 A
Pull out the handle to avoid the measurement being wrongly adjusted.
A
B
B
C
Position the paper on the backgauge (A) and side lays left or right (B).
To move paper stacks, please use the paper knock-up block (C) provided.
(Run backgauge to the front for turning the paper stack).
- 17 -
EBA 485 A • EBA 485 EP
• Operation •
The clamp moves automatically when cutting is activated.
The paper can also be pressed in advance.
Clamping and cutting is activated by pressing button (A) on the front table.
A
+ = Pre-clamping
= Clamp returns
+ =
Cutting sequence with automatic clamping
- 18 -
• Operation •
Close the safety guard.
Cutting activation:
Press both buttons of the two-handed control system activation (A) simultaneously and them pressed until the paper is completely cut.
A
To interrupt or stop cutting:
To interrupt or stop cutting, release both buttons (A) of the two-hand control.
- 19 -
• Operation •
EBA 485 A • EBA 485 EP
Only EBA 485 EP
Only EBA 485 A
- 20 -
Operating elements
A - Front safety guard
B - Safety two-handed control system
Pre-clamping and cutting
C - Overload switch
(blade drive/clamp drive/ backgauge drive)
D - Backgauge control (EP)
E - Main switch
F - Hand-wheel (EP) or crank handle for backgauge setting
G - Key switch
H - Backgauge
I - Side lay left and right
J - Display cutting size (EP, cm or inch)
K - Select program step up (Programming) or fixed dimension (Standard 21 cm)
L - Select program step down (Programming) or fixed dimension (Standard 10,5 cm)
M - Stop and delete input
N - Start
O - Memory multiple cut
P - Keypad
Q - Changeover cm - inch (LED - display)
R - Clear program
S - Select program
T - Enter
U - Program number
V - Program step
W - Cut is blocked
X - Display multiple cut
Y - Display cutting size (cm or inch)
Z - Changeover cm/inch a - Measuring unit (cm or inch)
• Operation •
EBA 485 A
C
D
A
B
E
- 21 -
EBA 485 A
Start machine
• Main switch E to position "I", insert the key
G for the control panel and turn it to the right.
Open the front safety guard A
Only by EBA 485 A
Cutting to specified dimensions
• The measurement is set with the backgauge crank.(A) The symbol – rotary direction – moves to the right on the display (B) (see picture C). The rotary direction of the
(backgauge crank (A) is indicated on the right. Keep turning the backgauge crank to the right until a measurement appears
(see picture E).
The reference position is reached. The cutting size can now be set with the handle (A).
If the backgauge is right at the front the symbol – rotary direction – ill move to the left (see picture D). Turn the backgauge crank to the left until the rotary direction appears on the right in the display (see picture C). Afterwards turn the backgauge crank to the right until a measurements appears (see picture E). The reference position is reached. The cutting size can now be set with the handle (A). Proceed to position from the rear.
The measurement scale in cm or inch has a
LED display store see page 20, picture below left.
• Insert paper and move by means of the stacking angle to the backgauge lay on the left a . For information on how to
I .
• Close the front safety guard
• Release the cut.
A.
H and side
Cut according to markings
• Adjust the backgauge with the crank handle
F to the back.
• Insert paper and move by means of the stacking angle to the backgauge lay on the left I.
• Turn the crank handle F
H and side
to the right until the marking on the paper to be cut is below the cutting line indicator.
• Operation •
EBA 485 A • EBA 485 EP
EBA 485 EP
Start machine
• Main switch E to position "I", insert the key
G for the control panel and turn it to the right.
Open the front safety guard
•
Press S button N
A
backgauge H moves to the rear and searches for the reference position, wait until a measurement is shown in the display D.
EBA 485 EP = 45 cm, 17,72 inches
Warning!
Before storing or cutting a measurement please check if the correct measurement scale (cm or inch) see above is stored.
For information on how to store see picture below left.
Cutting to specified dimensions
• Enter dimension on the numerical key pad
LED "S" to e.g. 7 cm.
W
(If a wrong dimension is entered this can be corrected by pressing the
• Press the S
S button dimension is
H
S
S button pressed and
button s button).
N
is released, the
moves to a measurement of
• Insert paper and move by means of the stacking angle to the backgauge lay on the left
appears.
I .
• Close the front safety guard
• Release the cut.
A.
P approached, LED "S" disappears.
Dimensions below 9 cm 3,5 cm can only be approached with the held. (When the backgauge
9 cm measurement 9 cm blinks, keep
button pressed, backgauge
H
H moves
and side
Cut according to markings
• Adjust the backgauge with the hand-wheel to the back.
• Insert paper and move by means of the stacking angle to the backgauge lay on the left I.
• Turn the hand-wheel F
H and side
to the right until the marking on the paper to be cut is below the cutting line indicator.
F
Only EBA 485 EP
• The further the hand-wheel F
is turned to the right, the quicker the backgauge moves. If the hand-wheel is turned to the left the backgauge will return quicker.
- 22 -
• Operation •
Eject function
If button j
L is pressed instead of button after inserting the measurement P , the backgauge will advance forwards so that
S N paper can be removed. Finally the backgauge moves to the last setting.
,
Adjust the eject-dimension
• Press
•
• display.
• Insert the desired dimension.
(Standard is 20 cm).
g p p , hold, and press
Store dimension.
+ s
T e
Escape the program mode.
on
Program buttons
Press , the display) or
Press g p p , b
Store dimension.
and hold, and press hold, and press on the display) j b j
programs
(
(
ö
appears on
Ü
appears
•
•
Enter the desired dimension (For example:
29,7 cm x 21 cm can be entered for DIN A4)
Display in cm or inch
•
Press i display changes between cm and inch (see page 20 and 22).
Multiple cut
• Enter the start dimension on the display
• Advance to the measurement with the button
• Press
N
• Push the paper to the backgauge
T
.
will be on.
• Enter the multiple cut size.
• Pressing the size.
s
S
button M
H .
button the red LED "M "
• After cutting has been activated press
X button is pressed, the
S
light
S
P button.
Every time the backgauge will advance by the multiple cut size.
.
shows the actual
Exiting program-mode
• Pree T button LED "M " the display.
X is cleared on
- 23 -
EBA 485 A • EBA 485 EP
• Operation •
Programming
Only EBA 485 EP
This control system enables you to store 99 programs with 99 programmable steps. One step represents one measurement. After entering the program numbers you are able to change between several program steps with the button
First figure on display = program number.
Second figure = program step.
Dimensions below 9 cm/3,54 inch can only be approached with the
"
" u too high.
j and b .
S button held pressed.
" on the display the entered dimension is too low.
o " on the display the entered dimension is
Each program step corresponds to one dimension. The indicated program step can be overwritten at any time. These programs remain stored when the machine is off. Should you change to another dimension unit all programmed measurements are converted into the new unit (cm or inch).
•
•
•
•
Entering a program
•
Press
01
(Top number
• If measurement is shown on the display program is reserved.
g
... p
99
P appears on the display.
Enter program number 01 ... 99.
U on display = program number).
the desired measurement with the hand-wheel
J
• Enter dimension, or move the backgauge to
the
Should an ejection be desired before this cut press immediately press
Press
dimension of the first program).
Or: p + s p
V .
F .
Store the dimension next program step appears
• Enter the next dimension.
g Store the dimension next program step appears.
• Should the entered program be required
S
, hold, and press
S
T .
(program is closed).
again (backgauge moves to the
Escape the program mode.
- 24 -
• Operation •
Eject function program
The eject function can be added each time a measurement is entered and ejects before advancing to the next measurement.
An eject at the end of a program must be programmed in the first step at the program.
If the dimension and eject function are stored in the program step the program number appears on the display U .
Example of a program eject function
•
•
• Press
•
•
•
• p 0 8 c c
1 6 g
2 0 g p s p program 08 delete previous program
, hold, and press step 1 on 16,0 cm step 2 on 20,0 cm
T eject ( e blinks)
Store the dimension escape the program mode
How the example works
•
• p
S
0 8
• Insert paper
• Release cut 1
• Press p s
S button
• Paper is ejected (
• Turn the paper
• Release cut 2
•
U blinks) start program 08
proceeds to position escape the program mode
•
•
• p
0 1
Top number on display = program number.
Lower number = program step.
• Enter the cut size on the display g Store the dimension.
•
Enter multiple cut size.
Press T
X button
" appears on the display.
E V appears on the display.
Press g p
Press "
... 9 9 Enter program number 01 ... 99.
Store the dimension.
+ s
T button again F ..... N .
P
Escape the program mode.
.
and multiple cut size
•
•
Maximum nine multiple cuts can be entered.
- 25 -
EBA 485 A • EBA 485 EP
• Operation •
•
• p press "
0 1 ... 9 9
•
Press button
X
Enter program number 01 ... 99.
c
" appears on the display.
twice.
Each program has to be cancelled separately.
Deleting a dimension when programming
Press s and overwrite the dimension.
Choose a program step appears.
Press p , hold, and press T ß V
Enter the desired number of steps (e.g.
lights.
0 5 ).
Change a step j
next step
previous step
Insert a step
Press p , hold, and press b
A new program step is inserted before the displayed program step is shown.
Delete a step
Press p , hold, and press is deleted.
j Program step
The following number of steps are updated.
- 26 -
• Operation •
Working with programs
• Press
• 01 ... p
With the button dimension.
With
"
99
" appears on the display
Enter program number 01 ... 99 j and b you are able to change between several program steps.
With S s
the backgauge moves to the indicated
the backgauge stops.
General
LED "S" lights Cut is blocked.
LED "S" is off the actual dimension appears.
In the program mode the ejection of paper is not possible. The ejection of paper has to be programmed.
j
Escape the program mode
•
Press
•
Press p s
"
X
" appears on the display.
escape the program mode.
Cutting activation
Warning!
• Run backgauge to the front for turning the paper stack.
• Do not interrupt the upward movement of the blade by performing switching procedures.
• Release blade only when LED "S" out.
A .
W has gone
• Close the front safety guard
• Blade must always be at the top and be covered by the clamp. Do not touch the blade.
(see safety information on page 36).
Risk of injury!
- 27 -
EBA 485 A • EBA 485 EP
• Blade and cutting stick replacement •
If the cutting quality decreases:
• Check the cutting depth (see page 36).
• Check the cutting stick (see page 32).
• Replace or grind the blade (see page 28 - 36).
The blade cannot be ground if the blade height is less than 83 mm/3,29 inches.
A new blade must be used.
The blade may only be ground by a qualified supplier or from the manufacturer
Krug & Priester, D-72336 Balingen.
Danger! Risk of injury!
The blade is extremely sharp. Do not extract or transport the blade without protection.
Changing the blade may only be performed by trained staff.
- 28 -
• Blade and cutting stick replacement •
Turn the blade depth adjustment screw to the left until it stops. (Screwdriver found in tool set
(A).
Close the safety guard (1.).
Lower the blade by pressing both cutting buttons (2.). Keep one button pressed and turn off the main switch (3.).
- 29 -
EBA 485 A • EBA 485 EP
C
A
B
• Blade and cutting stick replacement •
The 3 eccentrics are now exposed and should be turned counter clockwise to position "0" with the special wrench and attachable extension pipe (A) (in the tool set). The slot must correspond to position "0" (B).
Unscrew the blade screws (C) on the right hand side.
Remove the special wrench and turn on the main switch until the blade returns to the home position.
- 30 -
• Blade and cutting stick replacement •
A
Position the main switch to "0" (1.)
Remove the 2 blade screws on the elongated holes (2.). Then put the blade changing tool (A) into place and fasten it to the blade (3.).
3.
2.
1.
1.
3.
A
Remove the rest of 2 blade screws (1.)
Loosen the grips (2.) of the blade changing tool (A) lightly and allow the blade to be taken downwards out of the machine (3.). Place the blade into the blade carrier (B) and screw it into place (4).
B
4.
2.
- 31 -
EBA 485 A • EBA 485 EP
1.
• Blade and cutting stick replacement •
A
Take out the cutting stick with a small screwdriver. If needed the cutting stick can be turned or exchanged. (The cutting stick can be used eight times).
2.
A
3.
Replacing the cutting stick (not the blade).
• Turn the blade adjusting screw (A) to the left until it stops. (Otherwise the first cut will be too deep).
• Remove the cutting stick according to top picure.
• Turn the cutting stick (the non-used side must be near to the blade) and plug it into the holding bolt.
Danger! Risk of injury!
Cutting test after replacing the cutting stick
(not the blade)
• Insert the paper and release the cut.
• If the last sheet of paper is not cut along the entire length turn the blade adjusting screw
(A) ¼ turn to the right.
• If the last sheet is still not completely cut along the entire length.
- 32 -
• Blade and cutting stick replacement •
A
Take the exchange blade carefully out of the blade box and screw it to the blade changing tool (A).
• Make sure there is a space ot 11 mm or
0.43 inches! (B).
• Blade must be covrted! (C).
Danger! Risk of injury!
11 mm
0.43 inch
C
B
B
C
1.
A
Place the blade to be exchanged with the blade changing tool (A) mounted (1.), into the blade carrier and push it up to the top and screw it into place with the grips (2.).
2.
- 33 -
EBA 485 A • EBA 485 EP
1.
A
2.
• Blade and cutting stick replacement •
Lightly tighten 2 of the 5 blade screws with washers (1.). Remove the blade changing tool (2.). Lightly tighten the remaining blade screws with washers (3.).
Lightly screw in the right blade screw with the washer (A) when the blade is lowered.
3.
1.
Remove all tools and distribute paper along the entire cutting length (1.).
Turn main switch to position "I" (2.).
2.
- 34 -
• Blade and cutting stick replacement •
1.
Close the safety guard (1.) Lower the blade by pressing both cutting buttons (2.). Keep one button pressed and turn off the main switch (3.).
3.
4.
5.
A
2.
Open the safety guard (4.). With the special wrench (B) the 3 eccentrics should be screwed down (5.)until the paper is cut along the entire length of the blade (The blade must remain parallel, not too deep into cutting stick).
2.
A
Tighten the blade screws (A) on the right hand side.
Turn main switch to position "I" (1.). Blade will return to upper position. Tighten the 4 blade screws (2.) firmly.
Warning
The clamp must always overlap the blade! (see page 36).
Danger! Risk of injury!
1.
- 35 -
EBA 485 A • EBA 485 EP
A
• Blade and cutting stick replacement •
Paper cutting test. If the last sheet or several sheets are not completely cut, gradually turn the knob for blade depth adjustment (A)
¼ turn to the right until the paper is cut along the entire length. Do not set too low as blade will become blunt sooner.
Warning!
Danger!
Blade must always be covered by the pressing bar (see picture below at the left).
Clamping
OK
Blade
OK
- 36 -
• Maintenance and cleaning •
D
Maintenance work may only be performed by trained staff.
Danger! Disconnect the mains before starting any service work or before removing the cover.
Grease the backgauge (A) control weekly with a grease gun. Advance the backgauge as far as possible to the front. (Use non-resinous oil or grease).
Grease the remaining parts twice a year (see picture).
The main switch must be on "0" (B).
Remove lower panel (C).
Tools in tool set.
• Remove any paper.
• Grease the machine.
• Check the 4 joining bolts and 2 pushing bars for wear (D). If necessary inform your service personnel.
• Mount the machine.
= Greasing points on the machine.
- 37 -
EBA 485 A • EBA 485 EP
• Maintenance and cleaning •
Safety test
The safety regulations are according to the regulations of the country where the cutting machine is operated. The manufacturer recommends a safety check is made every 5 years by an authorised service team.
- 38 -
• Possible malfuntions •
Machine does not function!
Is the machine plugged in?
Main switch to position "I"? (A)
Control system activated? (B)
(Turn key to the right)
Release a cut see page 19.
- 39 -
EBA 485 A • EBA 485 EP
• Possible malfuntions •
Cut cannot be made.
• If cover is open: close it.
• If cover is closed: open and re-close it. (Security check).
A, B
Machine turns off:
• Machine overloaded.
Safety button (A) ejects.
(Allow 1 minute cooling time and reset the safety button (A).
• Machine blocked.
• Blade is blunt.
Eliminate the cause, and push the safety button (A).
Only EBA 485 EP
• Backgauge blocked
Safety button (B) ejects.
Eliminate the cause, and push the safety button (B).
Safety button for:
A = Blade drive
A = Clamping drive
B = Backgauge drive
- 40 -
• Possible malfuntions •
A Does not cut through the last sheet:
• Turn or turn around the cutting stick (A), readjust the blade by means of the blade adjusting knob (B)
(see page 36).
Poor cutting quality or blade stays in the paper stack.
• Change the blade (C) (see pages 28 - 36).
B
C
- 41 -
EBA 485 A • EBA 485 EP
• Possible malfuntions •
Motor runs but blade does not move downwards.
• Security brake has been activated!
Inform the Service Team!
• www.eba.de "Service" [email protected]
A
C
B
Display illumination off
• Machine is plugged in? (A)
• Main switch on position "I"? (B)
• Push in the safety button! (C)
• Check the units fuse and the on-site circuit breaker!
- 42 -
• Possible malfuntions •
EBA 485 EP
Cut cannot be made.
• Measurement has not been reached correctly.
• LED "S" W
Push the
does not turn off.
S button again.
Check the security cover (see page 40).
• Measurement below 9 cm/3,54 inch
Hold the S button N until the measurement is achieved.
None of the above mentioned methods helped to solve the problem:
Contact Service Team under
• www.eba.de
"Service" [email protected]
- 43 -
EBA 485 A • EBA 485 EP
• Accessories •
Recommended accessories:
Blade
• Nr. 9000 021 EBA 485 A, EBA 485 EP
Cutting stick (6 pieces)
• Nr. 9000 022 EBA 485 A, EBA 485 EP
Blade changing tool 1
• Nr. 9000 518 EBA 485 A, EBA 485 EP
Paper knock-up block 1
• Nr. 9000 521 EBA 485 A, EBA 485 EP
1 Included in delivery
- 44 -
• Technical data •
A
Technical data:
• Power supply: 230V/50Hz/1~,120V/60Hz/1~
• Cutting height: 80 mm
• Sound level EN 13023: < 70 dB (A)
• Leakage current < 3,5mA
• Power cord gauge min. 1,5mm 2 (230V).
• Power cord gauge AWG 12 (20A) (120V)
The exact technical specifications can be found on the technical specifications sticker (A) on the machine. A wiring diagram is found in the electrical switch box.
To claim under guarantee, the machine must still carry its original identification label.
IDEAL 4810-95
IDEAL 4850-95
IDEAL 4850-95 EP
IDEAL 5221-95 EP
IDEAL 6550-95 EP
Cutting- length
mm
475
475
475
520
650
Table- depth
mm
458
458
450
520
610
Minimum space requirement
(B X T X H) mm
755 x 970 x 1360
755 x 970 x 1230
755 x 970 x 1230
855* x 1067 x 1260
995 x 1260 x 1220
Weight
kg
194
209
215
262**
304
- 45 -
EBA 485 A • EBA 485 EP
• Technical data •
This machine is approved by independent safety laboratories and is in compliance with the EC-regulations 2006/42/EG and
2004/108/EG.
Sound level information:
The sound level is < 70 db (A) as defined by
EN 13023.
Subject to alteration without notice.
- 46 -
D EG-KONFORMITÄTSERKLÄRUNG
GB EC-declaration of conformity
F Déclaration de conformité CE
- Hiermit erklären wir, daß die Bauart von
- Herewith we declare that
- Par la présente, nous déclarons que
485 A
485 EP
UL- IDENT. Nr.
10485001
10485002
- folgenden einschlägigen Bestimmungen entspricht
- complies with the following provisons applying to it
- sont conformes aux dispositions pertinentes suivantes
2006/42/EG:
Maschinenrichtline, EC Machinery directive, EC Directives machines.
2004/108/EG:
EMV Richtline, EMV Electromagnetic compatibility directive,
EMV directives compatibilité électromagnétique.
- Angewendete harmonisierte Normen insbesondere
- Applied harmonised standards in particular
- Normes harmonisées utilisées, notamment
EN 60204-1; EN 1010-1; EN 1010-3; EN 55014-1; EN 55014-2;
EN 61000-3-2; EN 61000-3-3; EN ISO 12100-1; EN ISO 12100-2;
EN ISO 13857; EN ISO 11204; EN 13023; EN ISO 13849-1
29.12.2009
Datum
Bevollmächtigter für technische Dokumentation
Authorized representative for technical documentation
Représentant autorisé pour la documentation technique
Krug & Priester GmbH u. Co KG
Simon-Schweitzer-Str. 34
D-72336 Balingen (Germany)
- 47 -
EBA • Made in Germany
Document Shredders
Trimmers and Guillotines
• EBA Krug & Priester
•
72336 Balingen
•
Germany
•
www.eba.de •
文档公共链接
广告
