advertisement
4.3” Factory Mount Mirror
Monitor with Built-In DVR
User Manual
Installation Guide
MM-4320-DVR
4.3” Factory Mount Mirror Monitor with Built-In DVR
Introduction
Thank you for purchasing your EchoMaster Mirror Monitor.
EchoMaster mirror monitors are designed to improve safety by providing high quality images from camera inputs. This may help to improve vehicle maneuvering capabilities by displaying blind spots or areas not normally visible to the driver.
Please ensure you read and understand all aspects of this manual before fitting or using your EchoMaster mirror monitor.
Box Contents
u User Guide u Mirror Monitor u Main Harness u Universal Mounting Button u Cable Management u Allen Key u 8GB Micro SD Card
Key Features
u Factory replacement mirror u Dual video sensing inputs u Auto-dimming display u Built-in shock sensor u Built-in forward looking camera
with Digital Video Recorder u Built-in selectable motion detection
2 email - [email protected] (US) tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast) email - [email protected] (Europe)
Installation Guide
MM-4320-DVR
4.3” Factory Mount Mirror Monitor with Built-In DVR
Fitting Instructions
The MM-4320-DVR will replace your factory fitted rearview mirror.
Remove the original mirror from the vehicle and replace with the
MM-4320-DVR. If your factory mounting bracket differs from the
MM-4320-DVR, there is a supplied metal button that can be bonded to the windshield to allow the new mirror to fit.
Once the unit is in place, run the connections cable across the headliner of the vehicle and down the A pillar.
Please ensure that you do not impede the operation of any airbags that may be located in the A pillar of the vehicle. Any cable passing these airbags should be run behind the airbag and not in front of it.
Once the cable has been routed down to the dashboard, connect the camera inputs and power connections as shown in the wiring diagram section of this manual.
Operating Instructions
Upon powering up the screen, the DVR screen will be displayed and recording will start automatically, as long as an SD card is inserted.
The SD card slot is located on the right-hand side of the unit. Please take care when inserting the card as improper insertion can damage the card and the mechanism.
To switch to V1 video input, press and hold the REC button for 2 seconds.
To revert back to the DVR display, press the REC button again briefly.
The screen will automatically switch to V2 when it detects a video signal on that input.
email - [email protected] (US) tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast) email - [email protected] (Europe)
3
Installation Guide
MM-4320-DVR
4.3” Factory Mount Mirror Monitor with Built-In DVR
Operating Instructions
(continued)
Pressing the menu button when a video signal is being viewed will allow you to adjust the following parameters.
Brightness Adjust the brightness level of the display (0-100).
Color Adjust the color of the display (0-100).
Contrast Adjust the contrast of the display (0-100).
Sharpness Adjust the display sharpness (0-100).
Reset This resets all values to the default setting.
The screen will automatically turn on when it detects a signal input on either channel. If a signal is detected on both channels then V2 will take priority.
To stop and start recording, press the REC button. If a shock event is detected, the unit will automatically protect the current file.
When using the DVR function the menus can be accessed by pressing the
MENU button. (Recording must be stopped for this to be enabled).
The menu categories can be scrolled through by pressing the MODE button and then each list can be scrolled through by pressing the REC button.
To enter a menu feature, press the REC button and change the values using the up and down arrow buttons. Repeatedly pressing the REC button will back out to the main menu.
Pressing MENU again will exit the menu structure.
Movie Mode menu:
Movie Mode
Movie Quality
Movie Clip Time
Movie Off Time
Adjust the resolution of the recording.
Adjust the picture quality (lower quality will increase the amount of video able to be recorded).
Sets the length of each individual recording clip.
This sets how long after power off the unit will continue to record for.
4 email - [email protected] (US) tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast) email - [email protected] (Europe)
Installation Guide
MM-4320-DVR
4.3” Factory Mount Mirror Monitor with Built-In DVR
Operating Instructions
(continued)
Motion Event Record This sets the recording length when a motion event is
Sound Record
Mic Sensitivity
Scene detected (requires the unit to be powered constantly).
This turns the built-in microphone recording on or off.
Adjust the sensitivity of the built-in mic.
Set different scene modes to improve picture quality in
different
Exposure
White Balance
ISO Sensitivity
Change the exposure value of the camera.
Change the white balance of the camera.
Change the ISO setting of the camera.
Still Capture:
Still Image Size
Still Quality
Scene
different
Exposure
White Balance
ISO Sensitivity
Color
Effect
This sets the size of the picture when taking still images. Lower resolution will allow for more pictures to be stored on the card.
This adjusts the image quality for still images
(lower quality offers more storage).
This adjusts the camera settings to compensate for
Adjust the exposure level of the camera.
Adjust the white balance of the camera.
Adjust the ISO setting of the camera.
Adjust the color setting of the camera.
Apply certain graphical effects to the still images.
Playback Menu:
Volume – Adjust the playback volume through the internal speaker.
Delete – Allows you to delete one or all of the files (protected files cannot be deleted).
Protect – This allows you to protect any files not currently protected.
Media Tool:
Format SD Card – This will format the contents of the currently inserted card
(Warning: this will delete all contents).
SD Card Info – This shows information about the currently inserted card.
email - [email protected] (US) tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast) email - [email protected] (Europe)
5
Installation Guide
MM-4320-DVR
4.3” Factory Mount Mirror Monitor with Built-In DVR
Operating Instructions
(continued)
General Settings:
Beep
Clock Settings
Date Format
Stamp
Language
Flicker
LCD Rotate
LCD Power Save
Protect Level
Motion Detection
Turns the button press beep on or off.
Allows you to set the current date and time.
Change the displayed format of the date.
You can set whether the date and time are permanently embedded into the recordings.
Choose the language of the menu structure.
You can change the flicker rate between 50 and 60 Hz to improve playback on different devices.
This allows you to invert the recording on a vertical plane.
This allows you to set the automatic turn-off of the display.
This will allow you to adjust the built in G sensor settings (lower is less sensitive).
This will set the camera’s sensitivity to movement when
Reset Setup
FW Version using the automatic motion detect feature.
This will reset all settings to the default values.
Display the current firmware version on the unit.
Pressing the mode button while in the DVR screen will switch between the Recording,
Photo and Playback modes. Pressing the right-hand arrow button while recording will mute the built-in microphone. Pressing the menu button while recording will lock the current file to prevent overwriting.
Wiring Diagram
Main Harness
6 email - [email protected] (US) tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast) email - [email protected] (Europe)
+12V Ignition
GND
(Red)
(Black)
V1
V 2
Video Input
Reverse Camera Input
MM-4320-DVR
4.3” Factory Mount Mirror Monitor with Built-In DVR
Dimensions (mm)
Installation Guide
Specifications
Screen Size
Aspect Ratio
Power Supply
Resolution
Luminance
Contrast
TV Format
OSD Languages
Video Inputs
Audio Inputs
Triggers
Current Draw
Operating Temperature
Parking Guidelines
Connection Type
Dimensions (mm)
MM-4320-BT
4.3”
16:9
12VDC
480x272
1000
500:1
Auto
0
0
Multi
2
300-1000mA
-20C - +60C
No
RCA
278 x 83 x 46 email - [email protected] (US) tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast) email - [email protected] (Europe)
7
15500 Lightwave Drive, Suite 202, Clearwater, Florida 33760
Woolmer Way, Bordon, Hampshire, United Kingdom email - [email protected] (US) tel - 1-800-477-2267 (East Coast) - 1-888-883-2790 (West Coast) email - [email protected] (Europe)
EchoMaster is a Power Brand of AAMP Global.
EchoMaster.com
advertisement
Related manuals
advertisement