advertisement
PAC-MAN AIR HOCKEY
Air Hockey Table Owner’s Manual.
Assembly, operation and care instructions.
Contents
Foreword
We would like to thank you very much for purchasing the Pac-Man Air Hockey from
Bandai Namco Amusement America Inc.
For your own safety, please read through this instruction manual that we have prepared for you thoroughly, and take precautions when using the product. We hope that you will become accustomed to the product quickly.
2
Product Specifications
Electrical Power (MANUAL SELECT)
Domestic 120 VAC @ 60 Hz, 5 amps
International 240 VAC @ 50 Hz, 2.5 amps
Temperature
32° to 100° Fahrenheit
Humidity
Must not exceed 95% relative humidity
Assembled “Pac-Man Air Hockey” Dimensions
Width – 48,5”
Depth – 88”
Height – 37”
Weight Assembled ~360 lbs.
Before Assembling
WARNING
THIS TABLE WEIGHS 360 POUNDS
1. Please make sure you have at least 4 strong adults to assist with assembly and installation*.
*Note: Bandai Namco Amusement America accepts no responsibility for any injury that may result from the assembly, installation or moving of this product.
2. Inspect to make sure all the parts are included and not damaged.
3. Prior to assembly, you must ensure there is sufficient space for placing or shifting this product.
Tools required for Assembling*
Pac Man Air Hockey Manual
Scissors
Hex Allen Key - 4mm (located inside the bag manual)
*Note: Prepare the above specified tools. Be careful not to damage the product while using these tools
4
Product Parts
1. For Legs
4 Pac-Man Plastic Legs
4 Adjustable Leg Levelers
24 Roundhead screws M6 x 35mm
24 Split Lock washers M6
24 Flat washers M6
2. For Protection Acrylic
2 Steel Locker central protection acrylic
4 side protection acrylic
1 central protection acrylic
16 Roundhead screws M6 x 35mm
3. For Player
2 doors keys
1 AC Power cord
2 pucks
2 mallets
6
Assembly Procedures
1. Use scissors or a knife to cut* through the packing tape.
*Note: Do not cut too deep or you will damage the unit.
Panel marked
“Parts Inside”
2. Open the carton, make sure the wooden side of the Pac-Man Air Hockey is facing up.
3. Use Hex Allen Key - 4mm to unscrew the 10 screws on the panel with the sticker “Parts
Inside’’ on it. Once the panel is opened, please take out the parts* indicated on page 5 and 6.
*Note: Do not remove Air Blower
4. Take out the 4 Pac Man Air Hockey plastic legs and screw the adjustable leg levelers into the base of the legs.
8
5. Place the legs on the bottom surface of the table. Ensure alignment and then attach with roundhead screws M6 x 35mm and split lock washer M6 and flat washer M6
6. Plug in the AC Power Cord
Plug
AC Power
Fuse
ON / OFF
7. Ensure all legs are tightly attached then flip the table 90 degrees keeping the cardboard top on to prevent scratching. This action requires 4 people. Please make sure you have at least 4 strong adults to assist with assembly and installation. Flip it another 90 degrees to place the legs on the ground.
Finished Position
8. Using 2 steel locker central protection, assemble the central protection acrylic. Ensure alignment and then attach with 4 roundhead screws M6 x 35mm.
10
9. Assemble the side protection acrylic. Ensure alignment and then attach with 3 roundhead screws 6 x 35mm, each peace.
Safety Instructions for Use and Play
Risk of Electric Shock
Hazardous voltage, which can cause electrical shock, exists inside the equipment. Only qualified personnel should work inside the equipment.
Playing Warnings
Do not hit the puck with the mallet when the puck is not level and flat.
Spectators should not stand by the side of the table. This may cause injury.
Hold the mallet by the handle and not the base or the puck may hit fingers.
This game features flashing lights, which may not be suitable for photosensitive epilepsy.
Hardware and Software Configuration
First, ensure the power is off. Open the door with a key. Hold the panel's handle and pull it out until half of the power panel is exposed.
Open the door with a key
Handle on the panel
Hardware Descriptions
Note: Do not touch open terminals or exposed wires while the game is on. Risk of electric shock.
Power supply
12VDC to CPU
Power supply
24VDC to Motor
Motor Switch CPU
Main CPU
12
Hardware Specifications
Risk of Electric Shock
Avoid electric shock. Do not touch open terminals or exposed wires. Please turn off the game to perform repairs.
Hazardous voltage, which can cause electrical shock, exists inside the equipment. Only qualified personnel should work inside the equipment.
Warning
Machine is shipped set to 120 Volts, if operating this machine in an area that uses 220 Volts, both power supplies must be changed or severe damage will occur.
To change the voltage, swipe the red switch inside the both power supplies.
Power Supply
Provides power to all internal components, such as the motherboard, coin mechanism, motor. etc. The +12 VDC and +24VDC are separated to ensure no interference to components when one has an insufficient supply or an unstable supply of power.
Note: +24 VDC is on the left +12 VDC is on the right
Motor PCB
Motor PCB switches the blower motor on and off. When the green LED is on, the motor is on! Main PCB control the motor PCB.
Main PCB
Controls the operation of all internal components. Malfunctions or errors with any of the components can be diagnosed by looking at the DISPLAY indicators on the main PCB.
LED is lit if
SD Card is reading
LED is lit if main PCB is working
Display
&
SD CARD
MENU
4 push buttons
RESET
Restart the
Main PCB
Software Specifications
Short Menu: i. Press up to set VOLUME IN GAME, adjust the volume using up and down then press change for complete. ii. Press down to set VOLUME DEMO, adjust the volume using up and down then press change for complete.
Complete Menu:
Press change to enter menu, up and down to choose options, cancel to return.
14
Menu Diagram:
Parts
Cabinet parts
Ref
13
14
15
16
9
10
11
12
2
3
4
5
1
6
7
8
Part Description
Protection Acrylic Set
Protection Acrylic Center
Protection Acrylic Left
Protection Acrylic Right
Side Red Rubber Perimeter Rail Trim
Side Aluminum Rail
Red Plastic Corner
Red Corner Finishing
End Red Rubber Perimeter Rail Trim
End Aluminum Rail
Acrylic Play Field 10MM “Pac Man Air Hockey”
Leg “Pac Man Air Hockey”
Leg Leveler
Protection Bracket Set
Protection Bracket Left/Right
Protection Bracket Center
Yellow Push Button
Cover Plate with Hole for Push Button
Complete Door Set “Pac Man Air Hockey”
Lock
Cover Plate
16
Part#
AH90-68-000-258-00
AH90-68-000-258-99
AH90-68-000-258-98
AH90-68-000-258-97
AH96-68-000-256-00
AH10-31-002-070-00
AH90-55-000-142-00
AH90-55-000-146-00
AH96-68-000-257-00
AH90-31-002-069-00
AH40-21-000-957-00
AH10-57-000-035-00
AH20-31-000-095-00
AH05-68-000-259-00
AH05-68-000-259-99
AH05-68-000-259-98
AH53-60-000-064-00
AH10-31-002-122-00
AH05-68-000-252-00
AH26-64-700-006-00
AH10-31-002-109-00
Cash Box and Tickets Parts (Arcade Version Only)
Ref
1
2
3
4
Part Description
Coin Acceptor
Coin Door Assembly
Ticket Door Assembly
TL-002IV Ticket Dispenser
Part#
AH83-42-400-042-00
AH83-68-000-253-00
AH83-68-000-254-00
AH82-42-400-106-00
Electronics
Ref
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Part Description Part#
Line Filter 125/250 VCA 6A
Speaker 4” 40W 4 OHMS
Solenoid Matic 12V HST-100.1 12VCC-100%
Optical Goal Sensor
AH78-42-500-007-00
AH54-40-000-032-00
AH36-42-400-107-00
AH79-68-000-255-00
Power Cord 6 feet
Display PCB “Air Rev. 1”
Blower
Rail Sensor Chip “Piezoelectric” 27MM 30V
SD Card with Software “Pac Man Air Hockey”
Power Supply 24V 150W “Meanwell LRS-350-24”
AH51-40-200-104-06
AH15-41-700-062-00
AH58-40-000-009-00
AH75-40-600-003-00
AH15-43-000-036-00
VG88-16287-00
Power Supply 12V 150W “Meanwell RS-150-12”
Main PCB “Geany Rev. 5.1”
VG88-14591-00
AH15-43-000-035-00
Motor PCB “Motor Rev.1”
AH15-41-700-064-00
Complete Hardness “Pac Man Air Hockey (EXP)”
AH50-40-100-110-00
18
Decal Prints
Ref
1
2
Part Description
Decal Set Complete (4 pieces)
Decal Side (Colorful Ghost’s)
Decal Side (Blue Ghost’s)
Decal End
Security Decal Set “Pac Man Air Hockey”
Part#
AH40-68-000-260-00
AH40-68-000-260-99
AH40-68-000-260-98
AH40-68-000-260-97
AH40-68-000-261-00
Consumable Parts
Ref
1
2
Part Description
Puck (Red)
Mallet
Part#
AH95-55-000-016-00
AH90-68-000-039-00
20
© BANDAI NAMCO Amusement America Inc.
First Edition Published in October 2016
BANDAI NAMCO AMUSEMENT AMERICA INC.
951 Cambridge Drive
Elk Grove Village, IL 60007
847.264.5610
FAX: 847.264.5611
Technical Assistance (USA)
Parts: 847.264.5612 Tech Service: 847.264.5614
Fax: 847.264.5613
Part No. AH45-17059-00
Specifications of the machine and contents of this operation manual are subject to change without prior notice due to product improvements.
advertisement
Related manuals
advertisement