TRACEABLE LCD Timer Instruction manual

Below you will find brief information for LCD Timer. The TRACEABLE LCD Timer is a versatile count-up and count-down timer that can be used for a variety of purposes, including timing cooking, workouts, laboratory experiments, and more. The device can also be used as as a standard clock. The timer has a variety of features, including memory recall, an alarm, and fast setting. The device can be attached to a magnetic surface, clipped to a shirt pocket, or stood up on a table.

PDF

Document

TIMER FEATURES
1. LCD Count-down/count-up Timer together with Clock.
2. 6 digit display showing HOUR, MINUTE, and
SECOND for both Timer and Clock.
3. Automatic count up after Timer counts down to zero.
4. Count-down Timer:
Maximum setting is 23 HR.
59 MIN. 59 SEC. and counts
down at 1 second resolution.
Count-up Timer:
Maximum count-up range is
23 HR. 59 MIN. 59 SEC. at
1 second resolution.
5. Memory recall function for count-down Timer.
6. Timer alarm sounds for 1 minute when Timer counts down to zero.
7. Individual setting buttons for HOUR, MINUTE, and SECOND
setting.
COUNT-DOWN TIMER SETTING (See Fig. 1)
1. Switch the [TIMER/CLOCK] slide switch to [TIMER] position, 0:00
00 and I TIMER I mark will show on display.
2. Press [HR] button to advance hour digits. Button Confirmation
sound can be heard for each press of button. Press and hold [HR]
button for 2 seconds will fast set the hour digits..
3. Press [MIN] button to advance minute digits. Button confirmation
sound can be heard for each press of button. Press and hold [MIN]
button for 2 seconds will fast set the minute digits.
4. Press [SEC] button to advance second digits. Button confirmation
sound can be heard for each press of button. Press and hold [SEC]
button for 2 seconds will fast set the second digits.
5. If setting is not the desired one, press [RESET] button once to
reset Timer to zero and set time again.
COUNT-DOWN TIMER START/STOP
1. After time setting is ready, press [START/STOP] button once and
Timer will start to count down at 1 second resolution.
2. When Timer is counting, press [START/STOP] button once and
Timer will stop.
3. Press [START/STOP] button once and Timer will start counting
again.
COUNT-DOWN TIMER ALARM
1. When Timer counts down to 0 HR 00 MIN 00 SEC (0:00 00 will
show on display), [TIMES UP] mark will flash on display, Timer
alarm starts to sound for 1 minute and Timer will automatically
continue to count up at 1 second resolution.
2. Timer alarm and count-up time can be stopped by pressing [HR],
[MIN], [SEC], [START/STOP] or [RESET] button.
COUNTDOWN TIMER MEMORY RECALL
1. After Timer alarm stops, press [START/STOP] button once can
recall pre-setting desired count-down time. [MEMORY] mark will
appear on display.
2. Press [START/STOP] button 2nd time can start Timer and Timer
will count down for another lap. [MEMORY] mark will disappear.
COUNT-UP TIMER SETTING (See Fig. 1)
1. When Timer is in rest stage (0 HR. 00 MIN. 00 SEC.), press
[START/STOP] button once will activate count-up feature and
2.
3.
4.
5.
Timer starts to count up at 1 second resolution. Button confirmation
sound can be heard.
Press [START/STOP] button 2nd time can stop the count-up Timer.
Press [START/STOP] button 3rd time, count-up Timer will continue
to count up at 1 second resolution.
Press [START/STOP] button 4th time can stop the count-up Timer.
Press [RESET] button once will reset count-up Timer to zero.
COUNTDOWN AND COUNT-UP TIME MEASUREMENT:
1. Switch the [TIMER/CLOCK] slide switch to [TIMER] position.
2. Set desired time to count-down Timer by using the same procedure
as count-down Timer setting.
3. Press [START/STOP] button once to start the count-down Timer.
4. When Timer counts down to 0 HR 00 MIN 00 SEC (0:00 00 will
show on display), [TIMES-UP] mark will flash on display, Timer
alarm starts to sound for 1 minute and Timer will automatically
count up at 1 second resolution.
5. When you think the count-up period is good enough for you, press
[START/STOP] button once to stop the count-up Timer.
6. Elapsed period after Timer counts down to zero can be known from
the count-up time on display.
NORMAL TIME SETTING (See Fig. 1)
Switch the [TIMER/CLOCK] slide switch to [CLOCK] position, normal
time of clock with flashing colon will show on display.
REPLACEMENT OF BATTERY (See Fig. 2)
Follow the arrow direction, use a money coin to open the battery cover
at back side of Timer.
HOUR
Press [SET] button (button confirmation sound can be heard) and at
the same time press [HR] button (button confirmation sound can be
heard) to advance hour digits, Press [SET] button and simultaneously
press and hold [HR] button for 2 seconds will fast set the hour digits,
[AM] or [PM] mark will appear on display for 12 hour version clock.
Remove exhausted battery, insert a new 1.5V G-13 size button cell
battery (make sure positive 1+1 is facing yourself) and close battery
cover.
MINUTE
Press [SET] button (button beep sound) and at the same time press
[MIN] button (button beep sound) to advance minute digits. Press
[SET] button and simultaneously press and hold [MIN] button for 2
seconds will fast set the minute digits.
SECOND
Press [SET] button (button beep sound) and at the same time press
[SET] button (button beep sound) will reset second digits to zero
when second digits are within 0-30 sec. range. When second digits
are within 31-59 sec. range, press [SET] and [SEC] button will reset
second digits to zero and minute digit advance by 1.
TRACEABLE &reg;
LCD TIMER
INSTRUCTIONS
CLIP ATTACHMENT (See Fig. 2)
The Timer can clip on thin board or shirt pocket by using the plastic
clip at back side of Timer.
MAGNETIC ATTACHMENT (See Fig. 2)
The Timer can attach on iron or steel surface by using the magnet at
back side of Timer.
TABLE STANDING (See Fig. 2)
The Timer can stand on table surface by flipping out the metal stand
bar at back side of Timer.
&copy;2017 92-8906-40 Rev. 0 072517
">

Hello! I am an AI chatbot specifically trained to assist you with the Traceable LCD Timer Instruction manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant is out of keyboard. Please, try again later.

Key features

Count-up/count-down timer function
Standard clock functionality
6-digit display with hour, minute, and second
Timer alarm
Memory recall for count-down timer
Fast setting buttons for hour, minute, and second
Magnetic attachment
Clip attachment
Table stand
Automatic count-up after timer counts down to zero

Frequently asked questions

To use the LCD Timer as a clock, simply slide the [TIMER/CLOCK] switch to the [CLOCK] position. The normal time of the clock with a flashing colon will then be displayed.

To set the time on the LCD Timer, switch the [TIMER/CLOCK] slide switch to the [CLOCK] position. Then, press the [SET] button and at the same time, press or hold the [HR] button for fast setting. The [AM] or [PM] mark will appear on the display for a 12-hour version clock.

To use the count-down timer on the LCD Timer, slide the [TIMER/CLOCK] switch to the [TIMER] position. Press the [HR], [MIN], and [SEC] buttons to set the desired time and press the [START/STOP] button to begin the count-down. The timer will count down to zero and then automatically count up at 1 second resolution.

To use the count-up timer on the LCD Timer, slide the [TIMER/CLOCK] switch to the [TIMER] position. Press the [START/STOP] button to begin the count-up. To stop the count-up, simply press the [START/STOP] button again. To reset the count-up timer, press the [RESET] button.

To use the memory recall function on the LCD Timer, slide the [TIMER/CLOCK] switch to the [TIMER] position. Set the desired count-down time and press the [START/STOP] button to begin the count-down. After the timer reaches zero and the alarm sounds, press the [START/STOP] button to recall the pre-set count-down time. The [MEMORY] mark will appear on the display. Press [START/STOP] button 2nd time can start Timer and Timer will count down for another lap. [MEMORY] mark will disappear.