SML625BTBK / SML625BTW

TM

SML625BTBK / SML625BTW

INSTRUCTION MANUAL

www.singingmachine.com

The Singing Machine® is a registered trademark of The Singing Machine Co., Inc.

Warnings

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The Caution marking is located on the bottom panel.

DANGEROUS VOLTAGE: The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

ATTENTION: The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying this product.

DRIPPING WARNING: This product shall not be exposed to dripping or splashing, and no objects filled with liquids, such as vases, shall be placed on the product.

VENTILATION WARNING: The normal ventilation of the product shall not be impeded for intended use.

SAFETY VERIFICATION: This device is made and tested to meet safety standards of the FCC, requirements and compliance with safety performance of the U.S. Department of Health and Human Services and also with FDA Radiation Performance Standards 21 CFR Subchapter.

Warnings:

• This CD player employs a laser light beam. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury.

• The use of controls, adjustments, or procedures other than those specified herein might result in hazardous radiation exposure.

• The apparatus shall be used in an open area.

CAUTION!

Invisible laser radiation when open and interlocks defeated. Avoid exposure to beam.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE

THIS UNIT TO RAIN OR MOISTURE.

FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

The rating information is located at the rear of the unit.

INDUSTRY CANADA NOTICE:

This device complies with Industry Canada Iicense-exempt RSS standard(s).

Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that may cause undesired operation of the device.

CAN ICES-3(B)/NMB-3(B)

Class II equipment symbol.

This symbol indicates that the unit has a double insulation system.

Important Safety Information

1. Read these Instructions.

2. Keep these Instructions.

3. Heed all Warnings.

4. Follow all Instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings. Install in accordance with the Manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. Do not place objects filled with water, such as a vase, on the apparatus.

16. The AC mains plug is used as the power disconnect device and it should remain readily accessible and operable during intended use. In order to completely disconnect the apparatus from power, the mains plug should be completely removed from the AC outlet socket.

17. CAUTION: To reduce the risk of fire or explosion, do not expose batteries to excessive heat such as sunshine, fire or other heat sources.

— 1 —

Included

What’s in the box.

Main Unit

AC Adapter

Wired Microphone

Manual Welcome Kit

— 2 —

Audio/Video Cables

Location of Controls (Front) u v w y x

U

V

X at ak bp bq br

Display

Lense

bs

1. CD/USB/BT Button

2. PROGRAM/REPEAT

Button

3. Skip Back 9Button

4. AUTO VOICE CONTROL

Button

5. BLUETOOTH PAIRING

Button

6. BLUETOOTH indicator

7. ON/OFF Button

8. SKIP 10- Button (MP3)

9. BALANCE Control

10. USB Port

11. LINE IN Jack

12. MASTER VOLUME

Control

13. Play/Pause Button

14. Stop < Button

15. Skip Forward

: Button

16. MIC VOLUME control

17. RECORD Button

18. Record Indicator

19. DISCO LIGHT Button

20. Skip10+ Button (MP3)

— 3 —

21. ECHO Control

22. Mic Holder

23. Mic 2 jack

24. Mic 1 jack

25. Speaker

26. CDG Indicator

27. Play/Pause Indicator

28. Program Indicator

29. Repeat Indicator bo al am an ao ap aq aras bt bk bl bn bm

Location of Controls (Top/Rear) u v w x y

TOP VIEW

1. CD Door

2. CD open

U

— 4 —

REAR VIEW

3. VIDEO OUT Jack

4. AUDIO OUT Jack (R)

5. AUDIO OUT Jack (L)

6. DC IN Jack (5.8V)

Connection

Connecting the Microphone(s)

Microphones:

Connect a microphone into MIC jack 1 as well as MIC jack 2 (when desired).

Note: Do not drop or tap the Mic as damage to the Mic or speakers may occur.

Do not twirl the microphone cord as it will cause damage to the encased wiring.

u v

Connecting the Unit to a TV

VIDEO OUT

(yellow)

AUDIO OUT

(white - L red - R)

RCA cables

REAR VIEW OF TV

VIDEO

INPUT

R

AUDIO

INPUT

L

To output the video, lyrics and audio to your TV, perform the following steps:

Connect the RCA video cable

(Yellow) to the VIDEO OUT jack and the audio cables (White and Red) to the AUDIO OUT jacks located on the back of the

Singing Machine.

Connect the opposite end of the RCA video cable (Yellow) to the VIDEO IN jack and the audio cables (White and Red) to the

AUDIO IN on your TV.

Notes:

• This unit can be used with or without a TV, but it is highly recommended to use a TV in order to utilize all the features.

• Also refer to the TV’s User Guide.

• To see the lyrics on the screen, you must use a CD+G disc.

— 5 —

Connection

Connecting to AC Power

Connecting to LINE IN Jack

To External Unit

AUDIO OUTPUT

/ HEADPHONE JACK

LINE IN

Disco Lights

Insert the AC power cord into a conveniently located AC outlet having 120V AC, 60Hz.

Note:

Make all connections before connecting to AC power.

Connect an external device by using an appropriate cable

(3.5mm audio cable not included) as shown.

Note:

See page 17 to select and use the

LINE IN function.

1

Press the LIGHT button to switch on the lighting effect, press again to switch off.

u

— 6 —

Operation

Playing a CDG u w v x

1

Connect the unit as described previously; if using a CD+G, it is recommended to connect to a TV

(see page 5). Press the power

ON/

OFF button to turn the unit on.

2

Lift open the CD door and insert a

CD or a CD+G by gently pressing it on the center spindle. Then close the

CD door.

Note:

•

What is a CD+G?

A CD+G (CD+Graphics) is the standard format for most karaoke discs that will display the words on the screen.

• Never place anything other than a

CD in the compartment, as foreign objects can damage the unit.

• If no disc is inserted, “NO” will appear on the display.

• If connected to a TV and/or other audio source, adjust the volume of the external unit using its own volume control.

3

Repeatedly press the

CDG/USB/

BT button to select the CDG mode;

“---” will appear when searching the disc and then the total number of tracks will appear. When a CDG disc is inserted, the CDG indicator will light.

4

Press the

Play/Pause

button to start playback; if listening to a CD+G file, the image and lyrics will appear on the TV screen (if connected) and the PLAY/PAUSE Indicator will light.

— 7 —

Operation

Playing a CDG (Continued)

®X

®at

®U

®W y

5

Adjust the volume to a comfortable level using the MASTER VOLUME control.

6

Connect microphone(s) as shown on page 5, and slide the

ON/OFF

switch on the microphone to the ON position.

7

Adjust the MIC VOLUME control as desired. Increasing this control will increase the volume of both microphones.

8

Rotate the ECHO control to add an echo effect to your voice. Rotate towards

MAX to increase the echo effect.

®®V

9

AUTO VOICE CONTROL can be activated by rotating the AVC control. The higher this control is set to, the more the vocals on the multiplex recording will be muted when the singer starts to sing through the microphone. When the singer stops singing, the recorded vocals on the multiplex recording will resume to normal.

— 8 —

10

Rotate the BALANCE control clockwise to hear the music and recorded vocals from a multiplex recording or counterclockwise to hear the music only from a multiplex recording.

Note: To use the BALANCE control, a CD+G disc must be used, otherwise it will operate as a standard Balance control.

Operation

Playing a CDG (Continued)

®ak

®al

®am ak

11

SKIP: Advance or go back one track by pressing the

Skip Back

9

/Skip Forward : buttons.

12

REPEAT: During playback, press the PROG/REP button once to repeatedly play the selected song; the Repeat indicator will blink.

Press the PROG/REP button a second time to repeatedly play the whole CD; the Repeat indicator will light solid. Press it again to cancel Repeat function, the

PROG/REP indicator turns off.

®am

13

PROGRAM: You can program up to 20 tracks on any disc for playback in any desired order.

While in the Stop mode, press the PROG /REP button; the

Program indicator will blink and

“P00” will appear. Select the first track using the Skip Back 9/

Skip Forward : buttons. Press the PROG/REP button again to confirm the entry. After selecting the desired tracks the display will show P01, P02, etc. recognizing the tracks selected have been programmed and the program indicator will illuminate solid red.

Repeat to set up to 20 tracks into memory. When done, press the

Play/Pause

button to start playback.

Note:

• Press the Stop < button TWICE to stop and clear the program.

— 9 —

Operation

Playing a CDG (Continued) ap an ao

14

PAUSE: During playback, if you wish to pause the disc momentarily, press the

Play/Pause

button; the PLAY/PAUSE indicator will blink. Press again to resume normal playback.

15

Press the playback.

Stop < button to stop

16

Press the power ON/OFF button to turn the unit off.

— 10 —

Operation

Playing Songs from the USB y w u v

1

Connect the unit as described previously (see page 6). Press the power ON/OFF button to turn the unit on.

2

Insert a USB flash drive into the USB port on the unit so it faces upward.

Make sure to download music from the

Karaoke store, see page 21.

x

3

Repeatedly press the CDG/USB/BT button to select the USB mode; “usb” will appear when searching the drive and then the total number of files will appear.

Note: The USB mode cannot be accessed until a flash drive is inserted.

4

Press the

Play/Pause

button to start playback; if listening to an

MP3+G file, the image and lyrics will appear on the TV screen (if connected).

5

Adjust the volume to a comfortable level using the MASTER VOLUME control.

Note: If connected to a TV or other audio source, adjust the volume of the TV using its own volume control.

— 11 —

Operation

Playing Songs from the USB (Continued)

X at

U

6

Connect microphone(s) as shown on page 5, and slide the ON/OFF switch on the microphone to the ON position.

7

Adjust the MIC VOLUME control as desired. Increasing this control will increase the volume of both microphones.

8

Rotate the ECHO control to add an echo effect to your voice. Rotate towards MAX to increase the echo effect.

V

W

9

AUTO VOICE CONTROL can be activated by rotating the AVC control.

The higher this control is set to, the more the vocals on the multiplex recording will be muted when the singer starts to sing through the microphone.

When the singer stops singing, the recorded vocals on the multiplex recording will resume to normal.

10

Rotate the BALANCE control clockwise to hear the music and recorded vocals from a multiplex recording or counterclockwise to hear the music only from a multiplex recording.

— 12 —

Operation

Playing Songs from the USB (Continued) al ak ak

11

SKIP: Advance or go back one track by pressing the 9 or : buttons.

You can also skip ahead 10 files/ tracks using the Skip10+ button and skip back 10 files/tracks by

Skip 10- button.

SEARCH: When playing any audio from the USB, press and hold the

9

or : buttons. The USB will search at high speed in the forward or backward direction. Normal play will continue when you release the button.

During Stop mode you can also select a file using the 9 or : buttons to scroll right/left.

12

REPEAT: During playback, press the

REP/PROG button once during playback, the

REP indicator will blink and the current track will be repeated. Press the REP/PROG button twice, the REP indicator will blink, all MP3 tracks inside the current folder will be repeated continuously. Press the

REP/

PROG button three times, the REP indicator will light solid, all MP3 tracks will be repeatedly. To stop repeat function, press the button again; the REP indicator will turn off.

— 13 —

Operation

Playing Songs from the USB (Continued) am ap an ao

13

PROGRAM: You can program up to

20 tracks for playback in any desired order. While in Stop mode, press the

REP/PROG button; PROG indicator will blink and “P00”appear. Select the first track using 9 or : buttons, then press the REP/PROG button.

Repeat to set up to 20 tracks into memory. When done, press the

Play/Pause

button to start playback.

Note: Press the Stop < button TWICE to stop and clear the program.

14

PAUSE: During playback, if you wish to pause the music momentarily, press the

Play/Pause /

ENTER button. Press again to resume normal playback.

15

Press the playback.

Stop < button to stop

16

Press the

ON/OFF button to turn the unit off.

— 14 —

Operation

Using a Bluetooth Device v

3 u

4

1

Connect the unit as described previously.

Press the power ON/OFF button to turn the unit on.

v

2

Repeatedly press the

CDG/USB/BT button to select the Bluetooth mode;

“bt” will blink in the display as the unit automatically searches for and pairs a previously paired Bluetooth device (if previously paired). If no previously paired devices are present, connect as shown in the next step.

Note: You can also press the PAIR button to disconnect any paired devices in order to pair another device.

3

Turn on your device’s Bluetooth option in settings to search for a discoverable device with a Bluetooth signal. Select

“ Singing Machine” from the device results on the Bluetooth menu, “bt” will light solid in the display. Note: Also refer to the user manual of your Bluetooth device for detailed instructions.

4

The Bluetooth indicator will light and a successful pairing sound will be heard.

Notes:

• If your Bluetooth prompts you for a passcode during the pairing process, please enter “0000” to connect.

• On some Bluetooth devices, once pairing is complete, select your Bluetooth device as

“Use as Audio Device” or similar.

• If connection is lost after successful pairing, check to make sure the distance between speaker and Bluetooth-enabled device does not exceed 30 feet/10 meters.

•“Bluetooth” will blink on TV screen, and will stop blinking after successful connection.

— 15 —

Operation

Using a Bluetooth Device (Continued)

U ak

V ak

W y

5

To control your Bluetooth device from this unit, press the Play/Pause button to start playback. Press the

Play/

Pause

button during playback to pause the song.

6

Adjust the volume to a comfortable level using the MASTER VOLUME control on this unit as well as the volume on your

Bluetooth device.

7

Connect microphone(s) as shown on page 5, and slide the ON/OFF switch on the microphone to the ON position.

8

Adjust the MIC VOLUME control as desired. Increasing this control will increase the volume of both microphones.

9

Rotate the ECHO control to add an echo effect to your voice. Rotate towards MAX to increase the echo effect.

10

Adjust the balance between the speakers using the BALANCE control.

at al X

11

SKIP: Advance or go back one track by pressing the Skip Back 9/Skip

Forward : buttons.

12

Press the power turn the unit off.

ON/OFF button to

— 16 —

Operation

Using the LINE IN Jack u v w

1

Connect the unit as described previously (see page 6). Press the power ON/OFF button to turn the unit on.

2

Connect the external unit to the

LINE IN Jack on the front of this unit.

Connecting an external unit will allow the audio to be played through your

Singing Machine. LINE IN function is automatically selected once the audio cable is plugged in.

Notes:

• It is highly recommended to set the volume on the auxiliary unit to 1/3 or lower to avoid distortion.

• Skipping files/tracks is not possible on this unit when using an external device.

3

Adjust the volume using the

MASTER

VOLUME control on this unit or your external device’s volume control.

x

— 17 —

4

Connect microphone(s) as shown on page 5. Slide the ON/OFF switch on the microphone to the ON position.

Operation

Using the LINE IN Jack (Continued)

5

Adjust the MIC VOLUME control as desired. Increasing this control will increase the volume of both microphones.

y

6

Rotate the ECHO control to add an echo effect to your voice. Rotate towards MAX to increase the echo effect.

V W

U

7

Adjust the balance between the speakers using the BALANCE control.

8

Press the power turn the unit off.

ON/OFF button to

— 18 —

Operation

Recording Singing to the USB u w y

1

Connect the unit as described previously. Press the power

ON/OFF

button to turn the unit on.

RECORD CDG/CD MUSIC TO THE USB w y

2

Follow the “Playing a CDG” instruction described on page 7 - page 8 to start the CDG/CD music playback.

3

Insert a USB flash drive into the

USB port on the unit, press the REC button; the REC indicator will light up, the song will start over and recording will begin. When recording is finished, press the REC button again to stop.

RECORD BLUETOOTH MUSIC TO THE

USB

4

Follow the “Using a Bluetooth Device” instruction described on page 15 - page 16 to start the Bluetooth music playback.

5

Insert a USB flash drive into the

USB port on the unit, press the REC button; the REC indicator will light up, the song will be recording right the way. When recording is finished, press the REC button again to stop.

— 19 —

Operation

Recording Singing to the USB

W

U

W

RECORDING YOUR SINGING TO THE

USB

6

Connect microphone(s) as shown on page 5. Slide the ON/OFF switch on the microphone to the ON position.

7

Adjust the MIC VOLUME control as desired. Increasing this control will increase the volume of both microphones.

8

Insert a USB flash drive into the

USB port on the unit, press the REC button; the REC indicator will light up, recording will start immediately.

When recording is finished, press the

REC button again to stop.

9

All recorded music or recorded singing will be in the folder labelled

REC. CDG/CD music or singing recording will be saved in order starting from TRK01. (If CDG music is recorded, the graphic file will also be recorded.) Bluetooth music or singing recording will be saved in order starting from BT and then

BT~0.

Note: You cannot record from the

USB or Line in, only from a CD, CDG or

Bluetooth.

— 20 —

Operation

Where to Download MP3+G Files

Helpful Hints:

The .mp3 and .cdg files are delivered for download in a single, compressed MP3+G.zip file. The MP3+G file cannot be played as a .zip file on a USB flash drive. To play karaoke songs using a USB flash drive, the MP3+G.zip file must be unzipped as follow:

• Connect a USB flash drive to your computer.

• Download the MP3+G file from your Digital

Locker and save the .zip file to a folder on your computer.

• Double click the .zip file to open the .zip (you will see the .mp3 .cdg files to USB flash drive.

• Remove (eject) the USB flash drive from your computer.

Turn on the Singing Machine and connect the

USB flash drive.

To purchase and download karaoke music, please visit http://store.singingmachine.com to access over 12,000 of your favourite karaoke songs. You will need a USB flash drive (not included) to transfer the downloads to this unit.

Follow these easy steps:

1

2

Go to http://store.singmachine.com using your internet browser, and then register.

Select and purchase your favorite karaoke music from the Singing Machine

Download Store.

FAQ

• Where can I get additional help with the file formats?

While on the Singing Machine Store’s web page, simply click FILE FORMATS at the lower left.

3

Download your selected purchase(s) from the Singing Machine Digital Locker to your USB flash drive.

4

Insert the USB flash drive as shown on page 11 and have fun singing!

Note: Your downloaded songs can also be burned to a blank CDR/CDRW.

— 21 —

Troubleshooting Guide

Should this unit exhibit a problem, check the following before seeking service:

No Power

• Power is not on; press the power

ON/OFF button to turn power on.

• Confirm that the AC adapter is connected securely to the back of the unit.

• Connect the unit to a different outlet.

No Sound – General

• Master Volume is set to minimum; raise volume.

• Correct Function was not selected; select using the CDG/USB/BT button.

• If using an external device, raise the volume.

.

• Check if the LINE IN jack is still connected by a cable.

No Sound – If connected to a TV

• Volume on the TV is muted or too low.

• Correct source (usually AV) was not selected on the TV’s menu.

Lyrics do not appear on the TV screen

• If connected to a TV, Video plug is not connected properly; see page 5.

• If connected to a TV, select the correct source on the TV (usually AV).

• The file/track being played is not a track recording with lyrics. These are the only files that allow you to view the lyrics on the TV screen.

• Nothing will appear on the TV screen when using LINE IN or Bluetooth.

File(s) on USB Jack not playing

• The file is corrupted; replace the file.

• The file is not in a format this unit will play.

• The connected USB device is not supported by the product.

No sound from the microphone

• Make sure the microphone is firmly connected to the MIC 1 or MIC 2 jack.

• Make sure the

ON/OFF switch on the microphone is set to the ON position.

• Make sure the MIC VOLUME setting is not set too low.

• MASTER VOLUME is set to minimum; raise volume.

• Adjust The Echo control past the mid point on the Singing Machine.

The Bluetooth device cannot be paired or connected with the unit

• You have not activated the Bluetooth function of your device; see page 15 or refer to the Bluetooth device user’s manual.

• The system is not in pairing mode; press the Pair button to restart pairing.

The Music is not available on the unit after successfully connecting the Bluetooth

• Ensure your Bluetooth device can support the A2DP Bluetooth profile.

• The volume on the external Bluetooth device is set to low or muted; raise as desired.

— 22 —

Specifications

AUDIO

OUTPUT POWER (MAXIMUM) ................................................................................3.5 Watts (RMS)

OUTPUT IMPEDANCE ..................................................................................................................3 Ohms

CD PLAYER SECTION

FREQUENCY RESPONSE .............................................................................................. 100Hz - 20kHz

SIGNAL-TO-NOISE RATIO ............................................................................................................... 50dB

NUMBER OF PROGRAMS ...................................................20 Step Random Access Programming

SAMPLING SYSTEM.........................................................................................8 Times Over Sampling

BLUETOOTH

Bluetooth Version .....................................................................................................................V2.1+EDR

Working Distance ...........................................Up to 30 feet/10 meters measured in open space

USB

Format .................................................................................................................................................FAT32

Maximum Compatibility ..................................................................................................................32GB

AUX IN SECTION ...........................................................................3.5 mm Stereo Headphone Jack

MICROPHONE ....................-74db 600 Ohm Impedance with 6.3 mm Dynamic Microphone

POWER SECTION ............................................................................................................ DC 5.8V 1.5A

POWER CONSUMPTION .............................................................................................................. 8.7 W

DIMENSIONS (HxWxD) .............................12.8 x 7.8 x 8.5 inches / 32.5 x 19.8 x 21.5 cm

WEIGHT ...........................................................................................................................5.0 lbs / 2.2 kgs

Specifications are subject to change without notice.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG,

Inc. and any use of such marks by The Singing Machine Company is under license. Other trademarks and trade names are those of their respective owners.

— 23 —

Visit Our Website: www.singingmachine.com

The Singing Machine Company, Inc.

4060 E Jurupa Street, Unit B

Ontario, CA 91761-1413 USA

Copyright © 2017 All Rights Reserved.

PRINTED IN CHINA

625BT-1704-ENG01