HPE FlexFabric 5930 Switch Series

QuickSpecs

Overview

HPE FlexFabric 5930 Switch Series


HP FlexFabric 5930 32QSFP+ Switch

HP FlexFabric 5930-4Slot Switch

HP FlexFabric 5930 2QSFP+ 2-slot Switch

Page 1

QuickSpecs

Overview

Models

HP FlexFabric 5930 32QSFP+ Switch

HP FlexFabric 5930-4Slot Switch

HP FlexFabric 5930 2QSFP+ 2-slot Switch

Key features

•

•

•

•

•

Cut-through with ultra-low-latency and wire speed

VXLAN VTEP support for virtualized environments

High-density 10GbE and 40GbE spine/ToR connectivity

IPv6 support with full L2 and L3 features

Convergence-ready with DCB, FCoE, and TRILL


JG726A

JH179A

JH178A

Product overview

The HPE FlexFabric 5930 Switch Series is a family of high-density, ultra-low-latency, top-of-rack (ToR) switches that is part of the

HP FlexNetwork architecture's HPE FlexFabric solution.

Ideally suited for deployment at the aggregation or server access layer of large enterprise data centers, the HPE 5930 Switch Series is also powerful enough for deployment at the core layer of medium-sized enterprises.

With the increase in virtualized applications and server-to-server traffic, customers now require spine and ToR switch innovations that will meet their needs for higher-performance server connectivity, convergence of Ethernet and storage traffic, the capability to handle virtual environments, and ultra-low-latency all in a single device- the HPE FlexFabric 5930 Switch Series.

Features and benefits

Quality of Service (QoS)

• Powerful QoS features

–

Flexible queue scheduling including Strict Priority (SP), WRR, WDRR, WFQ, SP+WRR, SP+WDRR, SP+WFQ, Configurable Buffer, Time range,

–

Queue Shaping, CAR with 8kbps granularity.

Packet filtering and remarking: packet filtering at L2 (Layer 2) through L4 (Layer 4); flow classification based on source MAC address, destination MAC address, source IP (IPv4/IPv6) address, destination IP (IPv4/IPv6) address, port, protocol, and

VLAN.

Data center optimized

•

•

•

Flexible high port density the HPE FlexFabric 5930 Switch Series enables scaling of the server edge with 10GbE and 40GbE spine and ToR deployments to new heights with a high-density 32-port fixed port switch in a 1RU design, a 2 Slot Modular design with

Two 40GbE QSFP+ ports and a 4 Slot Design. Support for 10GbE SFP+, 10GBASE-T, Converged Port 1/10GbE or 4/8Gbps

Fiber Channel, and 40GbE ports.

High-performance switching cut-through and nonblocking architecture delivers low latency (~1 microsecond for 10GbE) for very demanding enterprise applications; the switch delivers high-performance switching capacity and wire-speed packet forwarding

Higher scalability

Page 2

QuickSpecs HPE FlexFabric 5930 Switch Series

Overview

•

•

•

•

•

•

•

•

•

•

HPE Intelligent Resilient Fabric (IRF) technology simplifies the architecture of server access networks; up to nine HP 5930 switches can be combined to deliver unmatched scalability of virtualized access layer switches and flatter two-tier networks using IRF, which reduces cost and complexity

Advanced modular operating system

Comware v7 software's modular design and multiple processes bring native high stability, independent process monitoring, and restart; the OS also allows individual software modules to be upgraded for higher availability and supports enhanced serviceability functions like hitless software upgrades with single-chassis ISSU

TRILL, SPB and EVB/VEPA

TRansparent Interconnection of Lots of Links (TRILL) is supported including support of TRILL with IRF, TRILL ECMP up to 8 paths. Support for Shortest Path Bridging (IEEE 802.1aq) with ECMP up to 8 paths. Edge Virtual Bridging with Virtual

Ethernet Port Aggregator (EVB/VEPA) provides connectivity into the virtual environment for a data center-ready environment

Reversible airflow enhanced for data center hot-cold aisle deployment with reversible airflow—for either front-to-back or back-to-front airflow

Redundant fans and power supplies

Internal redundant and hot-pluggable power supplies and dual fan trays enhance reliability and availability

Lower OPEX and greener data center provide reversible airflow and advanced chassis power management

Data Center Bridging (DCB) protocols provides support for IEEE 802.1Qbb Priority Flow Control (PFC), Data Center Bridging Exchange (DCBX), IEEE 802.1Qaz

Enhanced Transmission Selection (ETS), Explicit Congestion Notification (ECN) for converged FCoE, iSCSI and RoCE environments.

FCoE support provides support T11 standards-compliant FC-BB-5 Fibre Channel over Ethernet (FCoE), including FCoE Initialization

Protocol (FIP), FCP, Fiber Channel enhanced port types VE, TE and VF, NPV, NPIV, Fabric Name Server, RSCN, Login

Services, and name-server zoning, Per-VSAN Fabric Services, FSPF, Standard Zoning and Fiber Channel Ping.

Jumbo frames with frame sizes of up to 10,000 bytes on Gigabit Ethernet and 10-Gigabit ports, allows high-performance remote backup and disaster-recovery services to be enabled

VXLAN Support

VXLAN Layer 2 Gateway support for up to 4k tunnels

Dynamic VXLAN configuration

OVSDB support for dynamic VXLAN configuration

Manageability

•

•

•

•

•

Full-featured console provides complete control of the switch with a familiar CLI

Troubleshooting

–

Ingress and egress port monitoring

– enable network problem solving

Traceroute and ping enable testing of network connectivity

Multiple configuration files allow multiple configuration files to be stored to a flash image

sFlow (RFC 3176) provides wire-speed traffic accounting and monitoring

SNMP v1, v2c and v3 facilitate centralized discovery, monitoring, and secure management of networking devices

Page 3


Overview

•

•

•

•

•

Out-of-band interface isolates management traffic from user data plane traffic for complete isolation and total reachability, no matter what happens in the data plane

Remote configuration and management delivered through a secure command-line interface (CLI) over Telnet and SSH; Role-Based Access Control (RBAC) provides multiple levels of access; Configuration Rollback and multiple configurations on the flash provide ease of operation; remote visibility is provided with sFlow and SNMP v1/v2/v3, and is fully supported in HPE Intelligent

Management Center (IMC)

ISSU and hot patching provides hitless software upgrades with single-unit In Services Software Upgrade (ISSU) and hitless patching of the modular operating system

Autoconfiguration provides automatic configuration via DHCP autoconfiguration

NTP, SNTP and PTP Support synchronize timekeeping among distributed time servers and clients; Support for Network Time Protocol (NTP), Secure

Network Time Protocol (SNTP) and Precision Time Protocol (PTP) IEEE 1588v2 (2008)

Resiliency and high availability

•

•

•

•

•

•

•

•

HPE Intelligent Resilient Fabric (IRF) technology enables an HPE FlexFabric to deliver resilient, scalable, and secured data center networks for physical and virtualized environments; groups up to nine HPE 5930 switches in an IRF configuration, allowing them to be configured and managed as a single switch with a single IP address; simplifies ToR deployment and management, reducing data center deployment and operating expenses

IEEE 802.1w Rapid Convergence Spanning Tree Protocol increases network uptime through faster recovery from failed links

IEEE 802.1s Multiple Spanning Tree provides high link availability in multiple VLAN environments by allowing multiple spanning trees

Virtual Router Redundancy Protocol (VRRP) allows groups of two routers to dynamically back each other up to create highly available routed environments

Hitless patch upgrades allows patches and new service features to be installed without restarting the equipment, increasing network uptime and facilitating maintenance

Ultrafast protocol convergence (< 50 ms) with standard-based failure detection—Bidirectional Forwarding

Detection (BFD) enables link connectivity monitoring and reduces network convergence time for RIP, OSPF, BGP, IS-IS, VRRP, MPLS, and

IRF

Device Link Detection Protocol (DLDP) monitors link connectivity and shuts down ports at both ends if unidirectional traffic is detected, preventing loops in STPbased networks

Graceful restart allows routers to indicate to others their capability to maintain a routing table during a temporary shutdown and significantly reduces convergence times upon recovery; supports OSPF, BGP, and IS-IS

Layer 2 switching

•

•

MAC-based VLAN provides granular control and security; uses RADIUS to map a MAC address/user to specific VLANs

Address Resolution Protocol (ARP) supports static, dynamic, and reverse ARP and ARP proxy

Page 4


Overview

•

•

•

•

•

•

IEEE 802.3x Flow Control provides intelligent congestion management via PAUSE frames

Ethernet Link Aggregation provides IEEE 802.3ad Link Aggregation of up to 128 groups of 32 ports; support for LACP, LACP Local Forwarding First, and LACP Short-time provides a fast, resilient environment that is ideal for the data center

Spanning Tree Protocol (STP) supports STP (IEEE 802.1D), Rapid STP (RSTP, IEEE 802.1w), and Multiple STP (MSTP, IEEE 802.1s)

VLAN support provides support for 4,096 VLANs based on port, MAC address, IPv4 subnet, protocol, and guest VLAN; supports VLAN mapping

IGMP support provides support for IGMP Snooping, Fast-Leave, and Group-Policy; IPv6 IGMP Snooping provides Layer 2 optimization of multicast traffic

DHCP support at Layer 2 provides full DHCP Snooping support for DHCP Snooping Option 82, DHCP Relay Option 82, DHCP Snooping Trust, and

DHCP Snooping Item Backup

Layer 3 services

•

•

•

Address Resolution Protocol (ARP) determines the MAC address of another IP host in the same subnet; supports static ARPs; gratuitous ARP allows detection of duplicate IP addresses; proxy ARP allows normal ARP operation between subnets or when subnets are separated by a

Layer 2 network

Dynamic Host Configuration Protocol (DHCP) simplifies the management of large IP networks and supports client and server; DHCP Relay enables DHCP operation across subnets

Operations, administration and maintenance (OAM) support provides support for Connectivity Fault Management (IEEE 802.1AG) and Ethernet in the First Mile (IEEE 802.3AH); provides additional monitoring that can be used for fast fault detection and recovery

Layer 3 routing

•

•

•

•

•

•

•

Virtual Router Redundancy Protocol (VRRP) and VRRP Extended allow quick failover of router ports

Policy-based routing makes routing decisions based on policies set by the network administrator

Equal-Cost Multipath (ECMP) enables multiple equal-cost links in a routing environment to increase link redundancy and scale bandwidth

Layer 3 IPv4 routing provides routing of IPv4 at media speed; supports static routes, RIP and RIPv2, OSPF, BGP, and IS-IS

Open shortest path first (OSPF) delivers faster convergence; uses this link-state routing Interior Gateway Protocol (IGP), which supports ECMP, NSSA, and

MD5 authentication for increased security and graceful restart for faster failure recovery

Border Gateway Protocol 4 (BGP-4) delivers an implementation of the Exterior Gateway Protocol (EGP) utilizing path vectors; uses TCP for enhanced reliability for the route discovery process; reduces bandwidth consumption by advertising only incremental updates; supports extensive policies for increased flexibility; scales to very large networks

Intermediate system to intermediate system (IS-IS) uses a path vector Interior Gateway Protocol (IGP), which is defined by the ISO organization for IS-IS routing and extended by IETF RFC 1195 to operate in both TCP/IP and the OSI reference model (Integrated IS-IS)

Page 5


Overview

•

•

•

•

•

•

•

•

•

•

•

Static IPv6 routing provides simple manually configured IPv6 routing

Dual IP stack maintains separate stacks for IPv4 and IPv6 to ease the transition from an IPv4-only network to an IPv6-only network design

Routing Information Protocol next generation (RIPng) extends RIPv2 to support IPv6 addressing

OSPFv3 provides OSPF support for IPv6

BGP+ extends BGP-4 to support Multiprotocol BGP (MBGP), including support for IPv6 addressing

IS-IS for IPv6 extends IS-IS to support IPv6 addressing

IPv6 tunneling allows IPv6 packets to traverse IPv4-only networks by encapsulating the IPv6 packet into a standard IPv4 packet; supports manually configured, 6to4, and Intra-Site Automatic Tunnel Addressing Protocol (ISATAP) tunnels; is an important element for the transition from IPv4 to IPv6

Policy routing allows custom filters for increased performance and security; supports ACLs, IP prefix, AS paths, community lists, and aggregate policies

Bidirectional Forwarding Detection (BFD) enables link connectivity monitoring and reduces network convergence time for RIP, OSPF, BGP, IS-IS, VRRP, MPLS, and

IRF

Multicast Routing PIM Dense and Sparse modes provides robust support of multicast protocols

Layer 3 IPv6 routing provides routing of IPv6 at media speed; supports static routing, RIPng, OSPFv3, BGP4+ for IPv6, and IS-ISv6

Additional information

• Green IT and power improves energy efficiency through the use of the latest advances in silicon development; shuts off unused ports and utilizes variable-speed fans, reducing energy costs

Management

•

•

•

•

•

•

USB support

–

File copy allows users to copy switch files to and from a USB flash drive

Multiple configuration files stores easily to the flash image

SNMPv1, v2c, and v3 facilitate centralized discovery, monitoring, and secure management of networking devices

Out-of-band interface isolates management traffic from user data plane traffic for complete isolation and total reachability, no matter what happens in the data plane

Port mirroring enables traffic on a port to be simultaneously sent to a network analyzer for monitoring

Remote configuration and management is available through a command-line interface (CLI)

Page 6


Overview

•

•

•

•

•

•

•

•

•

•

•

•

IEEE 802.1AB Link Layer Discovery Protocol (LLDP) advertises and receives management information from adjacent devices on a network, facilitating easy mapping by network management applications

sFlow (RFC 3176) provides scalable ASIC-based wirespeed network monitoring and accounting with no impact on network performance; this allows network operators to gather a variety of sophisticated network statistics and information for capacity planning and real-time network monitoring purposes

Command authorization leverages RADIUS to link a custom list of CLI commands to an individual network administrator's login; an audit trail documents activity

Dual flash images provides independent primary and secondary operating system files for backup while upgrading

Command-line interface (CLI) provides a secure, easy-to-use CLI for configuring the module via SSH or a switch console; provides direct real-time session isibility

Logging provides local and remote logging of events via SNMP (v2c and v3) and syslog; provides log throttling and log filtering to reduce the number of log events generated

Management interface control provides management access through a modem port and terminal interface, as well as in-band and out-of-band Ethernet ports; provides access through terminal interface, Telnet, or secure shell (SSH)

Industry-standard CLI with a hierarchical structure reduces training time and expenses, and increases productivity in multivendor installations

Management security restricts access to critical configuration commands; offers multiple privilege levels with password protection; ACLs provide

Telnet and SNMP access; local and remote syslog capabilities allow logging of all access

Information center provides a central repository for system and network information; aggregates all logs, traps, and debugging information generated by the system and maintains them in order of severity; outputs the network information to multiple channels based on user-defined rules

Network management

HPE Intelligent Management Center (IMC) centrally configures, updates, monitors, and troubleshoots

Remote intelligent mirroring mirrors ingress/egress ACL-selected traffic from a switch port or VLAN to a local or remote switch port anywhere on the network

Security

•

•

•

•

•

Access control lists (ACLs) provide IP Layer 3 filtering based on source/destination IP address/subnet and source/destination TCP/UDP port number

RADIUS/TACACS+ eases switch management security administration by using a password authentication server

Secure shell encrypts all transmitted data for secure remote CLI access over IP networks

IEEE 802.1X and RADIUS network logins controls port-based access for authentication and accountability

Port security allows access only to specified MAC addresses, which can be learned or specified by the administrator

Page 7

QuickSpecs

Overview

Convergence


• LLDP-MED (Media Endpoint Discovery) defines a standard extension of LLDP that stores values for parameters such as QoS and VLAN to automatically configure network devices such as IP phones

Warranty and support

•

•

1-year warranty see http://www.hpe.com/networking/warrantysummary for warranty and support information included with your product purchase.

Software releases to find software for your product, refer to http://www.hpe.com/networking/support; for details on the software releases available with your product purchase, refer to http://www.hpe.com/networking/warrantysummary

Page 8


Configuration

Build To Order: BTO is a standalone unit with no integration. BTO products ship standalone are not part of a CTO or Rack-Shippable solution.

Standard Switch Enclosures

HP FF 5930-32QSFP+ Switch

• 32 QSFP+ ports (min=0 \ max=32)

• Must select min 1 Power Supply

• Must select min 2 Fan Trays

• 1U - Height

HP FF 5930-2Slot+2QSFP+ Switch


• 2 port expansion module slots



• 1U - Height

HP FF 5930 2-slot 2QSFP FB AC Bndl


• 1 - JH178A HP FF 5930-2Slot+2QSFP+ Switch

• 2 - JC680A HP 58x0AF 650W AC Power Supply

• 2 - JG552A HP X711 Frt(prt)-Bck(pwr) HV Fan Tray

Each Switch:



• 2 Power Supplies Standard (min=2 \ max=2)

• 2 Front to Back Fan Trays Standard (min=2 \ max=2)

• 1U - Height

PDU Cable NA/MEX/TW/JP (2 Cables)

• C15 PDU Jumper Cord (NA/MEX/TW/JP) (2 Cables)

PDU Cable ROW (2 Cables)

• C15 PDU Jumper Cord (ROW) (2 Cables)

HP FF 5930 2-slot 2QSFP BF AC Bndl




• 2 - JG553A HP X712 Bck(pwr)-Frt(prt) HV Fan Tray

Each Switch:



JG726A

See Configuration

NOTE: 1

JH178A

See Configuration

NOTE: 1

JH378A

See Configuration

NOTE: 1

JH378A#B2B

JH378A#B2C

JH379A

See Configuration

NOTE: 1

Page 9

QuickSpecs

Configuration


• 2 Back Fan to Front Fan Trays Standard (min=2 \ max=2)

• 1U - Height





HP FF 5930-4Slot Switch




• 2U - Height

HP FF 5930 4-slot FB AC Bundle


• 1 - JH179A HP FF 5930-4Slot Switch


• 2 - JH186A HP 5930-4Slt Front-to-Back Fan Tray

Each Switch:




• 2U - Height





HP FF 5930 4-slot BF AC Bundle




• 2 - JH185A HP 5930-4Slt Back-to-Front Fan Tray

•

Each Switch:



• 2 Back to Front Fan Trays Standard (min=2 \ max=2)

2U - Height




JH379A#B2B

JH379A#B2C

JH179A

JH380A

JH380A#B2B

JH380A#B2C

JH381A

JH381A#B2B

Page 10


Configuration



Configuration Rules:

Note 1 The following 40G Transceivers install into this switch:

HP X140 40G QSFP+ LC LR4 SM 10km 1310nm Transceiver

HP X140 40G QSFP+ MPO SR4 Transceiver

HP X140 40G QSFP+ MPO MM 850nm CSR4 300m Transceiver

HP X240 40G QSFP+ QSFP+ 1m Direct Attach Copper Cable



HP X240 40G QSFP+ to 4x10G SFP+ 1m Direct Attach Copper Splitter Cable



Box Level Integration CTO Models

CTO Solution Sku

HP 59xx CTO Switch Solution

• SSP trigger sku

CTO Switch Chassis




• Must select min 2 Fan Tray

• 1U - Height






• 1U - Height






Each Switch:




JH381A#B2C

JG505A

JG726A

See Configuration

NOTE: 1, 5

JG661A

JG325B

JG709A

JG326A

JG327A

JG328A

JG329A

JG330A

JG331A

JH178A

See Configuration

NOTE: 1, 5

JH378A

See Configuration

NOTE: 1, 5

Page 11

QuickSpecs

Configuration


• 1U - Height










Each Switch:





• 1U - Height









• 2U - Height






•

Each Switch:




2U - Height




JH378A#B2B

JH378A#B2C

JH379A

See Configuration

NOTE: 1, 5

JH379A#B2B

JH379A#B2C

JH179A

See Configuration

NOTE: 5

JH380A

See Configuration

NOTE: 5

JH380A#B2B

Page 12


Configuration








Each Switch:




• 2U - Height






Note 1 The following 40G Transceivers install into this switch: (Use #0D1 or #B01 quoted to switch if switch is CTO) - if applicable










Note 5 If the Switch Chassis is to be Box Level Factory Integrated (CTO), Then the #0D1 is required on the Switch Chassis and integrated to the JG505A - HP 59xx CTO Switch

Solution. (Min 1/Max 1 Router per SSP)

Rack Level Integration CTO Models

CTO Switch Chassis




• Must select min 2 Fan Tray

• 1U - Height

JH380A#B2C

JH381A

See Configuration

NOTE: 5

JG726A

See Configuration

NOTE: 1, 11

Page 13

JH381A#B2B

JH381A#B2C

JG661A

JG325B

JG709A

JG326A

JG327A

JG328A

JG329A

JG330A

JG331A

QuickSpecs

Configuration






• 1U - Height






Each Switch:





• 1U - Height










Each Switch:





• 1U - Height









JH178A

See Configuration

NOTE: 1, 11

JH378A

See Configuration

NOTE: 1, 11

JH378A#B2B

JH378A#B2C

JH379A

See Configuration

NOTE: 1, 11

JH379A#B2B

JH379A#B2C

JH179A

See Configuration

NOTE: 11

Page 14


Configuration


• 2U - Height






•

Each Switch:




2U - Height










Each Switch:




• 2U - Height






Note 1 The following 40G Transceivers install into this Switch: (Use #0D1 or #B01 if switch is

CTO) - if applicable







JH380A

See Configuration

NOTE: 11

JH380A#B2B

JH380A#B2C

JH381A

See Configuration

NOTE: 11

JH381A#B2B

JH381A#B2C

JG661A

JG325B

JG709A

JG326A

JG327A

JG328A

Page 15


Configuration

Note 11




If HP CTO Switch Chassis is selected for Rack Level Integration, Then the Switch needs to integrate (with #0D1) to the Rack.

Enter the following menu selections as integrated to the CTO Model X server above if order is factory built.

Modules

(JH178A, JH187A) System (std 0 // max 2) User Selection (min 0 // max 2)



(max 2 Single Modules or 1 Module Bundle)


(max 4 Single Modules, or 2 Module Bundles, or 2 Single Modules and 1 Module Bundle)

HP 5930 24p SFP+ and 2p QSFP+ Mod

• 24 SFP+ ports (min=0 \ max=24)


HP 5930 24p SFP+ and 2p QSFP+ Mod w Msec

• 24 SFP+ ports (min=0 \ max=24)


HP 5930 24p 10GBase-T and 2p QSFP+ Mod

• 24 1/10GBase-T ports


HP 5930 8-port QSFP+ Module


JG329A

JG330A

JG331A

JH180A

See Configuration

NOTE: 1, 2, 6

JH181A

See Configuration

NOTE: 1, 2, 5, 6

JH182A

See Configuration

NOTE: 2, 6

JH183A

See Configuration

NOTE: 2, 6

JH383A

See Configuration

NOTE: 2, 4

HP FF 5930 8-port QSFP 2 Mod Bundle

(Bundle Occupies 2 slots)

Module Bundle:

• 2 - JH183A HP 5930 8-port QSFP+ Module

•

Each Module Bundle:

16 QSFP+ ports (min=0 \ max=16)

Configurator Blue Text: NOTE: Each Module: 8 QSFP+ ports (min=0 \ max=8). 2 Modules in each bundle.

Page 16


Configuration

HP 5930 24p Conv Port and 2p QSFP+ Mod

• 24 Converged SFP+/FC ports (min=0 \ max=24)


HP FF 5930 24-port CP 2QSFP 2 Mod Bundle

(Bundle Occupies 2 slots)

Module Bundle (Occupies 2 slots):

• 2 - JH184A 5930 24p Conv Port and 2p QSFP+ Mod

Each Module Bundle:

• 48 Converged SFP+/FC ports (min=0 \ max=48)


Configurator Blue Text: NOTE: Each Module: 24 Converged SFP+/FC ports (min=0 \ max=24)

2 QSFP+ ports (min=0 \ max=2)


Note 1 The following Transceivers install into this Module's SFP+ Ports: (Use #0D1 or #B01 if switch is CTO) - if applicable

HP X130 10G SFP+ LC SR Transceiver

HP X130 10G SFP+ LC LR Transceiver

HP X130 10G SFP+ LC ER 40km Transceiver

HP X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable


HP X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable


HP X240 10G SFP+ SFP+ 7m Direct Attach Copper Cable

HP X125 1G SFP LC LH40 1310nm Transceiver


HP X125 1G SFP LC LH70 Transceiver

HP X120 1G SFP RJ45 T Transceiver

HP X120 1G SFP LC BX 10-U Transceiver

Note 2

HP X120 1G SFP LC BX 10-D Transceiver

HP X120 1G SFP LC SX Transceiver

HP X120 1G SFP LC LX Transceiver

The following 40G Transceivers install into this Module's QSFP+ Ports: (Use #0D1 or

#B01 if switch is CTO) - if applicable









JH184A

See Configuration

NOTE: 1, 2, 3, 5, 6

JH382A

See Configuration

NOTE: 1, 2, 3, 4, 5

JD092B

JD094B

JG234A

JD095C

JD096C

JD097C

JG081C

JC784C

JD061A

JD062A

JD063B

JD089B

JD098B

JD099B

JD118B

JD119B

JG661A

JG325B

JG709A

JG326A

JG327A

JG328A

JG329A

JG330A

Page 17


Configuration

Note 3

Note 4

Note 5

Note 6


The following FC Transceivers install into this Module's SFP+/FC Ports: (Use #0D1 or

BTO if switch is CTO) - if applicable

HP StoreFabric 16Gb FC/10GbE 100m SR SFP+ Transceiver

HP 8Gb Short Wave Fibre Channel SFP+ 1 Pack

HP 8Gb Long Wave 10km Fibre Channel SFP+ 1 Pack Transceiver

This Module Bundle takes up 2 slots, and is only offered on:

HP FlexFabric 5930 2-slot 2QSFP+ Front-to-Back AC Bundle

HP FlexFabric 5930 2-slot 2QSFP+ Back-to-Front AC Bundle

HP FlexFabric 5930 4-slot Front-to-Back AC Bundle

HP FlexFabric 5930 4-slot Back-to-Front AC Bundle

The following Transceivers install into this Module's SFP+ Ports: (Use #0D1 or #B01 if switch is CTO) - if applicable

HP X130 10G SFP+ LC LRM Transceiver

If the JH179A or JH188A is selected with this module, the following cables are not allowed to be selected:




Transceivers

SFP Transceivers





HP X120 1G SFP LC BX 10-U Transceiver

HP X120 1G SFP LC BX 10-D Transceiver



SFP+ Transceivers





HP X240 10G SFP+ SFP+ 0.65m DAC Cable

HP X240 10G SFP+ SFP+ 1.2m DAC Cable

HP X240 10G SFP+ SFP+ 3m DAC Cable

HP X240 10G SFP+ SFP+ 5m DAC Cable

JD093B

JG329A

JG330A

JG331A

JD092B

JD093B

JD094B

JG234A

JD095C#B01

JD096C#B01

JD097C#B01

JG081C#B01

Page 18

JD061A

JD062A

JD063B

JD089B

JD098B

JD099B

JD118B

JD119B

JG331A

H6Z42A

AJ718A

AW584A

JH378A

JH379A

JH380A

JH381A

QuickSpecs

Configuration

HP X240 10G SFP+ 7m DAC Cable

FC SFP+ Transceivers

HP 16Gb FC/10GbE 100m SFP+ XCVR

HP 8Gb Short Wave FC SFP+ 1 Pack

HP 8Gb LW 10km FC SFP+ 1 Pk Transceiver

QSFP+ Transceivers

HP X140 40G QSFP+ LC LR4 SM XCVR

HP X140 40G QSFP+ MPO SR4 XCVR

HP X140 40G QSFP+ CSR4 300m XCVR

HP X240 40G QSFP+ QSFP+ 1m DAC Cable



HP X240 QSFP+ 4x10G SFP+ 1m DAC Cable



Cables

AOC Cables

HP BLc 40G QSFP+ QSFP+ 7m AOC Cable



Multi-Mode Cables

HP .5m Multi-mode OM3 LC/LC FC Cable

HP 1m Multi-mode OM3 LC/LC FC Cable

HP 2 m Multimode OM3 LC/LC FC Cable





HP Premier Flex LC/LC OM4 2f 1m Cbl






MPO Cables


720205-B21

720211-B21

720208-B21

AJ833A

AJ834A

AJ835A

AJ836A

AJ837A

AJ838A

AJ839A

QK732A

QK733A

QK734A

QK735A

QK736A

QK737A

JC784C#B01

H6Z42A

AJ718A

AW584A

JG661A

JG325B

JG709A

JG326A#B01

JG327A#B01

JG328A#B01

JG329A#B01

JG330A#B01

JG331A#B01

Page 19


Configuration

HP MPO to 4 x LC 5m Cable

HP MPO to 4 x LC 15m Cable

HP Premier Flex MPO/MPO OM4 8f 10m Cbl



Internal Power Supplies

(JG726A, JH178A, JG727A, JH187A) System (std 0 // max 2) User Selection (min 1 // max 2) per switch

(JH378A, JH379A) System (std 2 // max 2) User Selection (min 0 // max 0) per switch

(JH179A, JH188A) System (std 0 // max 4) User Selection (min 2 // max 4) per switch

(JH380A, JH381A) System (std 4// max 4) User Selection (min 0 // max 0) per switch

HP 58x0AF 650W AC Power Supply

• includes 1 x c13, 300w

PDU Cable NA/MX/TW/JP

• C15 PDU Jumper Cord (NA/MX/TW/JP)

PDU Cable ROW

• C15 PDU Jumper Cord (ROW)

HP 58x0AF 650W DC Power Supply

K2Q46A

K2Q47A

QK729A

QK731A

H6Z30A

JC680A

See Configuration

NOTE: 1, 2

JC680A#B2B

JC680A#B2C

JC681A

See Configuration

NOTE: 1

JH336A

See Configuration

NOTE: 1

HP FF SW 650W 48V NEBS DC PSU


Note 1 If 2 power supplies are selected they must be the same Sku number.

Note 2

Remarks:

Localization (Wall Power Cord) required on orders without #B2B, #B2C (PDU Power

Cord) . (See Localization Menu)

REMARK: When Switches/Routers are Factory Racked, Then #B2B, or #B2C should be the Defaulted Power Cable option on the Switches/Routers.

Drop down under power supply should offer the following options and results:

Switch/Router to PDU Power Cord - #B2B in NA, Mexico, Taiwan, and Japan or #B2C

ROW. (Watson Default B2B or B2C for Rack Level CTO)

Switch/Router/Power Supply to Wall Power Cord - Localized Option (Watson Default

Page 20

QuickSpecs

HP X712 Bck(pwr)-Frt(prt) HV Fan Tray

HP 5930-4Slt Back-to-Front Fan Tray

HP 5930-4Slt Front-to-Back Fan Tray


Configuration for BTO and Box Level CTO)

Switch Options

Fan Trays

System (std 0 // max 2) User Selection (min 2 // max 2) per switch

(JH378A, JH379A, JH380A, JH381A) System (std 2 // max 2) User Selection (min 0 // max 0) per switch

HP X711 Frt(prt)-Bck(pwr) HV Fan Tray JG552A

See Configuration

NOTE: 1, 2

JG553A

See Configuration

NOTE: 1, 2

JH185A

See Configuration

NOTE: 1, 3

JH186A

See Configuration

NOTE: 1, 3


Note 1 Fan Trays cannot be mixed in the same switch enclosure

Note 2

Note 3

Remarks:

This power supply is only supported on JG726A, JH178A, JG727A and JH187A.

This power supply is only supported on JH179A and JH188A.

Watson Blue Text:

If there is any empty space below the switch in a rack when using Back to Front Fan

Trays, JG553A, the rack will receive an Air Plenum kit that takes up 1U of additional space in the rack. The Air Plenum kit is not required on fully configured racks. This only applies for CTO Rack Level Integration. The Air Plenum Kit is a non-saleable SKU, and is brought in automatically for CTO Factory Rack Level Integration.

Opacity Shield Kit

System (std 0 // max 1) User Selection (min 0 // max 1)

Page 21

QuickSpecs

Configuration

HP FF 5930-32QSFP+ Opcty Shld Kit

• Supported on JG727A

HP FF 5930-2Slot+2QSFP+ Opcty Shld Kit

• Supported on JH187A


HP FF 5930-4Slot Opcty Shld Kit

• Supported on JH188A


Note 1 If selected with a CTO Switch Solution, Quantity 1 of JG585A#B01 must also be ordered.

Tamper Evidence Labels

System (std 0 // max 1) User Selection (min 0 // max 1)

HP 12mm x 60mm Tmpr-Evidence (30) Lbl

• Supported on JG727A, JH187A, JH188A


Note 1 If selected with a CTO Switch Solution, Quantity 1 of JH062A#B01, JH189A#B01 or

JH190A#B01 must also be ordered.

Remarks:

Each JH062A, JH189A or JH190A would use 1 of JG585A.

JH062A#B01

See Configuration

NOTE: 1

JH189A#B01

See Configuration

NOTE: 1

JH190A#B01

See Configuration

NOTE: 1

JG585A#B01

See Configuration

NOTE: 1

Page 22


Technical Specifications

HP FlexFabric 5930-32QSFP+ Switch (JG726A)

32 QSFP+ 40GbE ports I/O ports and slots

Additional ports and slots

1 RJ-45 serial console port

1 RJ-45 out-of-band management port

Power supplies

1 USB 2.0

2 power supply slots

1 minimum power supply required (ordered separately)

Fan tray

Physical characteristics

2 fan tray slots

The customer must order fan trays, as fan trays are not included with the switch. This system requires two same-direction airflow fan trays to function properly.

The system should not be operated with only one fan tray for more than 24 hours. The system should not be operated without a fan tray for more than two minutes.

The system should not be operated outside of the temperature range of 32°F (0°C) to 113°F (45°C).

Failure to comply with these operating requirements may void the product warranty

Dimensions

Weight

17.32(w) x 25.98(d) x 1.72(h) in (44.00 x 66.0 x 4.37 cm)

28.66 lb (13 kg) shipping weight

Full configuration weight 28.66 lb (13 kg)

Memory and processor 1 GB flash; Packet buffer size: 12.2 MB, 4 GB SDRAM

Performance 10 Gbps Latency

Throughput

< 1 µs (64-byte packets) up to 1429 Mpps

Routing/Switching capacity 2560 Gbps

Environment

Routing table size

MAC address table size

120000 entries (IPv4), 60000 entries (IPv6)

288000 entries

Operating temperature 32°F to 113°F (0°C to 45°C)

Operating relative humidity

10% to 95%, noncondensing

Electrical characteristics

Acoustic

Frequency

Low-speed fan: 59.8 dB, High-speed fan: 74.4 dB

50/60 Hz

Maximum heat dissipation 597/1361 BTU/hr (629.83/1435.86 kJ/hr)

Safety

Voltage 90 - 264 VAC, rated

-40 to -75 VDC, rated

(depending on power supply chosen)

Maximum power rating 399 W

Idle power 175 W

Notes Idle power is the actual power consumption of the device with no ports connected.

Maximum power rating and maximum heat dissipation are the worstcase theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated.

UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser Products-Part 2;

IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR; GOST; EN 60950-1/A11; FDA 21 CFR

Page 23



Emissions

Immunity

Management

Notes

Services

Subchapter J; NOM; ROHS Compliance

VCCI Class A; EN 55022 Class A; ICES-003 Class A; ANSI C63.4 2003; AS/NZS CISPR 22 Class A; EN

61000-3-2:2006; EN 61000-3-3:1995 +A1:2001+A2:2005; EMC Directive 2004/108/EC; FCC (CFR 47,

Part 15) Class A

Generic

EN

ESD

ETSI EN 300 386 V1.3.3

EN 55024:1998+ A1:2001 + A2:2003

EN 61000-4-2; IEC 61000-4-2

Radiated

EFT/Burst

Surge

Conducted

Power frequency magnetic field

Voltage dips and interruptions

Harmonics

EN 61000-4-3; IEC 61000-4-3

EN 61000-4-4; IEC 61000-4-4

EN 61000-4-5; IEC 61000-4-5

EN 61000-4-6; IEC 61000-4-6

IEC 61000-4-8; EN 61000-4-8

EN 61000-4-11; IEC 61000-4-11

EN 61000-3-2, IEC 61000-3-2

Flicker EN 61000-3-3, IEC 61000-3-3

IMC - Intelligent Management Center; command-line interface; out-of-band management; SNMP

Manager; Telnet; FTP

The customer must order a power supply, as the device does not come with one. At least one JC680A or JC681A is required.

Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services, and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

HP FlexFabric 5930-4Slot Switch (JH179A)

I/O ports and slots 4 module slots




Power supplies

1 USB 2.0

4 power supply slots

2 minimum power supplies required (ordered separately)

Fan tray 2 fan tray slots

The customer must order fan trays, as fan trays are not included with the switch. This system requires two same-direction airflow fan trays to function properly.

The system should not be operated with only one fan tray for more than 24 hours. The system should not be operated without a fan tray for more than two minutes.

The system should not be operated outside of the temperature range of 32°F (0°C) to 113°F (45°C).

Failure to comply with these operating requirements may void the product warranty.

Physical characteristics Dimensions

Weight

17.32(w) x 25.98(d) x 3.47(h) in (44.00 x 66.0 x 8.81 cm) (2U height)

66.14 lb (30 kg) shipping weight

Full configuration weight 59.52 lb (27 kg)


Performance 10 Gbps Latency < 1 μs (64-byte packets)

Page 24



Reliability

Environment

Electrical characteristics

Acoustic

Frequency

Low-speed fan: 59.8 dB, High-speed fan: 74.4 dB

50/60 Hz





Safety


Idle power 139 W

Notes Idle power is the actual power consumption of the device with no ports connected.





Emissions

Throughput

Routing/Switching capacity up to 1429 Mpps

2560 Gbps

Routing table size 120000 entries (IPv4), 60000 entries (IPv6)

MAC address table size 288000 entries

MTBF (years)

MTTR (hours) 1

35.8

Operating temperature 32°F to 113°F (0°C to 45°C)



Immunity



Part 15) Class A

Generic ETSI EN 300 386 V1.3.3

EN EN 55024:1998+ A1:2001 + A2:2003

ESD

Radiated

EFT/Burst

Surge

EN 61000-4-2; IEC 61000-4-2

EN 61000-4-3; IEC 61000-4-3

EN 61000-4-4; IEC 61000-4-4

EN 61000-4-5; IEC 61000-4-5

Conducted


EN 61000-4-6; IEC 61000-4-6


IEC 61000-4-8; EN 61000-4-8

EN 61000-4-11; IEC 61000-4-11

Harmonics

Flicker

EN 61000-3-2, IEC 61000-3-2

EN 61000-3-3, IEC 61000-3-3

Page 25



Management

Services




HP FlexFabric 5930-2Slot+2QSFP+ Switch (JH178A)

I/O ports and slots 2 module slots


2 QSFP+ 40GbE ports



1 USB 2.0

Power supplies 2 power supply slots

1 minimum power supply required (ordered separately)

Fan tray 2 fan tray slots

The customer must order fan trays, as fan trays are not included with the switch. This system requires two same-direction airflow fan trays to function properly. The system should not be operated with only one fan tray for more than 24 hours. The system should not be operated without a fan tray for more than two minutes. The system should not be operated outside of the temperature range of 32°F

(0°C) to 113°F (45°C). Failure to comply with these operating requirements may void the product warranty.

Physical characteristics Dimensions 17.32(w) x 25.98(d) x 1.74(h) in (44.00 x 66.0 x 4.42 cm)

Weight (1U height)

Full configuration weight 39.68 lb (18 kg) shipping weight


Performance 10 Gbps Latency < 1 µs (64-byte packets)

Throughput up to 1071 Mpps

Routing/Switching capacity

1440 Gbps

Reliability

Routing table size 120000 entries (IPv4), 60000 entries (IPv6)

MAC address table size 288000 entries

MTBF (years)

MTTR (hours) 1

47.2

Environment Operating temperature 32°F to 113°F (0°C to 45°C)



Acoustic Low-speed fan: 59.8 dB, High-speed fan: 74.4 dB

Electrical characteristics Frequency 50/60 Hz






Page 26



Safety

Emissions

Immunity

Notes

Services

Management

Idle power

Notes

105 W

Idle power is the actual power consumption of the device with no ports connected.







Part 15) Class A

Generic ETSI EN 300 386 V1.3.3

EN EN 55024:1998+ A1:2001 + A2:2003

ESD

Radiated

EFT/Burst

Surge

EN 61000-4-2; IEC 61000-4-2

EN 61000-4-3; IEC 61000-4-3

EN 61000-4-4; IEC 61000-4-4

EN 61000-4-5; IEC 61000-4-5

Conducted


EN 61000-4-6; IEC 61000-4-6


IEC 61000-4-8; EN 61000-4-8

EN 61000-4-11; IEC 61000-4-11

Harmonics

Flicker

EN 61000-3-2, IEC 61000-3-2

EN 61000-3-3, IEC 61000-3-3



The customer must order a power supply, as the device does not come with one. At least one JC680A or JC681A is required.


Standards and protocols

(applies to all products in series)

BGP

RFC 1163 Border Gateway Protocol (BGP)

RFC 1771 BGPv4

RFC 1997 BGP Communities Attribute

RFC 2918 Route Refresh Capability

RFC 3392 Capabilities Advertisement with BGP-4

RFC 4271 A Border Gateway Protocol 4 (BGP-4)

RFC 4360 BGP Extended Communities Attribute

RFC 4456 BGP Route Reflection: An Alternative to

Full Mesh Internal BGP (IBGP)

RFC 4760 Multiprotocol Extensions for BGP-4

Device management

IPv6

RFC 2080 RIPng for IPv6

RFC 2460 IPv6 Specification

RFC 2461 IPv6 Neighbor Discovery

RFC 2462 IPv6 Stateless Address Autoconfiguration

RFC 2463 ICMPv6

RFC 2464 Transmission of IPv6 over Ethernet

Networks

RFC 2473 Generic Packet Tunneling in IPv6

RFC 2545 Use of MP-BGP-4 for IPv6

RFC 2563 ICMPv6

RFC 2711 IPv6 Router Alert Option

Page 27

QuickSpecs



RFC 1157 SNMPv1/v2c

RFC 1305 NTPv3

RFC 1591 DNS (client)

RFC 1902 (SNMPv2)

RFC 1908 (SNMP v1/2 Coexistence)

RFC 2573 (SNMPv3 Applications)

RFC 2576 (Coexistence between SNMP V1, V2, V3)

RFC 2819 RMON

Multiple Configuration Files

Multiple Software Images

SSHv1/SSHv2 Secure Shell

TACACS/TACACS+

General protocols

IEEE 802.1ad Q-in-Q

IEEE 802.1AX-2008 Link Aggregation

IEEE 802.1D MAC Bridges

IEEE 802.1p Priority

IEEE 802.1Q VLANs

IEEE 802.1s Multiple Spanning Trees

IEEE 802.1w Rapid Reconfiguration of Spanning

Tree

IEEE 802.3ad Link Aggregation Control Protocol

(LACP)

IEEE 802.3ae 10-Gigabit Ethernet

IEEE 802.3ag Ethernet OAM

IEEE 802.3ah Ethernet in First Mile over Point to

Point Fiber - EFMF

IEEE 802.3x Flow Control

RFC 768 UDP

RFC 783 TFTP Protocol (revision 2)

RFC 791 IP

RFC 792 ICMP

RFC 793 TCP

RFC 826 ARP

RFC 854 TELNET

RFC 856 TELNET

RFC 868 Time Protocol

RFC 896 Congestion Control in IP/TCP

Internetworks

RFC 950 Internet Standard Subnetting Procedure

RFC 1027 Proxy ARP

RFC 1058 RIPv1

RFC 1091 Telnet Terminal-Type Option

RFC 1141 Incremental updating of the Internet checksum

RFC 1142 OSI IS-IS Intra-domain Routing Protocol

RFC 1191 Path MTU discovery

RFC 1213 Management Information Base for

Network Management of TCP/IP-based internets

RFC 1253 (OSPF v2)

RFC 2740 OSPFv3 for IPv6

RFC 2767 Dual stacks IPv46 & IPv6

RFC 3315 DHCPv6 (client and relay)

RFC 4291 IP Version 6 Addressing Architecture

RFC 4862 IPv6 Stateless Address Autoconfiguration

RFC 5095 Deprecation of Type 0 Routing Headers in IPv6

MIBs

RFC 1213 MIB II

RFC 1907 SNMPv2 MIB

RFC 2571 SNMP Framework MIB

RFC 2572 SNMP-MPD MIB

RFC 2573 SNMP-Notification MIB

RFC 2573 SNMP-Target MIB

RFC 2574 SNMP USM MIB

RFC 2737 Entity MIB (Version 2)

RFC 3414 SNMP-User based-SM MIB

RFC 3415 SNMP-View based-ACM MIB

LLDP-EXT-DOT1-MIB

LLDP-EXT-DOT3-MIB

LLDP-MIB

Network management

RFC 2580 Conformance Statements for SMIv2

RFC 3164 BSD syslog Protocol

OSPF

RFC 1587 OSPF NSSA

RFC 2328 OSPFv2

RFC 3101 OSPF NSSA

RFC 3137 OSPF Stub Router Advertisement

RFC 3623 Graceful OSPF Restart

RFC 4577 OSPF as the Provider/Customer Edge

Protocol for BGP/MPLS IP Virtual Private Networks

(VPNs)

RFC 4811 OSPF Out-of-Band LSDB

Resynchronization

RFC 4812 OSPF Restart Signaling

RFC 4813 OSPF Link-Local Signaling

QoS/CoS

IEEE 802.1p (CoS)

RFC 2475 DiffServ Architecture

RFC 2597 DiffServ Assured Forwarding (AF)

RFC 3247 Supplemental Information for the New

Definition of the EF PHB (Expedited Forwarding

Per-Hop Behavior)

RFC 3260 New Terminology and Clarifications for

Page 28

QuickSpecs



RFC 1531 Dynamic Host Configuration Protocol

RFC 1533 DHCP Options and BOOTP Vendor

Extensions

RFC 1534 DHCP/BOOTP Interoperation

RFC 1541 DHCP

RFC 1542 Clarifications and Extensions for the

Bootstrap Protocol

RFC 1591 DNS (client only)

RFC 1624 Incremental Internet Checksum

RFC 1723 RIP v2

RFC 1812 IPv4 Routing

RFC 2030 Simple Network Time Protocol (SNTP) v4

RFC 2131 DHCP

RFC 2236 IGMP Snooping

RFC 2338 VRRP

RFC 2453 RIPv2

RFC 2581 TCP Congestion Control

RFC 2644 Directed Broadcast Control

RFC 2767 Dual Stacks IPv4 & IPv6

RFC 2865 Remote Authentication Dial In User

Service (RADIUS)

RFC 2868 RADIUS Attributes for Tunnel Protocol

Support

RFC 2890 Key and Sequence Number Extensions to GRE

RFC 3046 DHCP Relay Agent Information Option

RFC 3411 An Architecture for Describing Simple

Network Management Protocol (SNMP)

Management Frameworks

RFC 3412 Message Processing and Dispatching for the Simple Network Management Protocol (SNMP)

RFC 3413 Simple Network Management Protocol

(SNMP) Applications

RFC 3416 Protocol Operations for SNMP

DiffServ

Security

RFC 1321 The MD5 Message-Digest AlgorithmRFC

2818 HTTP Over TLSRFC 6192 Partial Support -

Protecting the Router Control Plane

Access Control Lists (ACLs)

SSHv2 Secure Shell

RFC 3417 Transport Mappings for the Simple

Network Management Protocol (SNMP)

RFC 3418 Management Information Base (MIB) for the Simple Network Management Protocol (SNMP)

RFC 3768 Virtual Router Redundancy Protocol

(VRRP)

RFC 4250 The Secure Shell (SSH) Protocol

Assigned Numbers

RFC 4251 The Secure Shell (SSH) Protocol

Architecture

RFC 4252 The Secure Shell (SSH) Authentication

Protocol

RFC 4253 The Secure Shell (SSH) Transport Layer

Protocol

RFC 4254 The Secure Shell (SSH) Connection

Protocol

Page 29

QuickSpecs


RFC 4292 IP Forwarding Table MIB

RFC 4293 Management Information Base for the

Internet Protocol (IP)

RFC 4364 BGP/MPLS IP Virtual Private Networks

(VPNs)

RFC 4419 Diffie-Hellman Group Exchange for the

Secure Shell (SSH) Transport Layer Protocol

RFC 4594 Configuration Guidelines for DiffServ

Service Classes

RFC 4601 Protocol Independent Multicast - Sparse

Mode (PIM-SM): Protocol Specification (Revised)

RFC 4604 Using Internet Group Management

Protocol Version 3 (IGMPv3) and Multicast

Listener Discovery Protocol Version 2 (MLDv2) for

Source-Specific Multicast

RFC 4607 Source-Specific Multicast for IP

RFC 4941 Privacy Extensions for Stateless Address

Autoconfiguration in IPv6

RFC 5340 OSPF for IPv6

RFC 5905 Network Time Protocol Version 4:

Protocol and Algorithms Specification

RFC2929 RADIUS Support DS for Radius


Page 30


Accessories

HP FlexFabric 5930 Switch Series accessories

Bundles

HP FlexFabric 5930 2-slot 2QSFP+ Front-to-Back AC Bundle

Included in this bundle: (1) FlexFabric 5930 2QSFP+ 2-slot Switch (JH178A), (2) HP X711 Front (port side) to

Back (power side) Airflow High Volume Fan Tray (JG552A), and (2) HP 58x0AF 650W AC Power Supply

(JC680A

HP FlexFabric 5930 2-slot 2QSFP+ Back-to-Front AC Bundle

Included in this bundle: (1) FlexFabric 5930 2QSFP+ 2-slot Switch (JH178A), (2) HP X712 Back (power side) to Front (port side) Airflow High Volume Fan Tray (JG553A), and (2) HP 58x0AF 650W AC Power Supply

(JC680A)

HP FlexFabric 5930 4-slot Front-to-Back AC Bundle

Included in this bundle: (1) FlexFabric 5930 4-slot Switch (JH179A), (2) HP FlexFabric 5930 4-slot Front (Port

Side) to Back (Power Side) Airflow Fan Tray (JH186A), and (4) HP 58x0AF 650W AC Power Supply (JC680A)

HP FlexFabric 5930 4-slot Back-to-Front AC Bundle

Included in this bundle: (1) FlexFabric 5930 4-slot Switch (JH179A), (2) HP FlexFabric 5930 4-slot Back

(Power Side) to Front (Port Side) Airflow Fan Tray (JH185A), and (4) HP 58x0AF 650W AC Power Supply

(JC680A)

HP FlexFabric 5930 24-port Converged Port and 2-port QSFP+ 2 Module Bundle

Included in this bundle: (2) HP 5930 24-port Converged Port and 2-port QSFP+ Module (JH184A)

HP FlexFabric 5930 8-port QSFP+ 2 Module Bundle

Included in this bundle: (2) HP 5930 8-port QSFP+ Module (JH183A)

Transceivers









HP X240 10G SFP+ SFP+ 7m Direct Attach Copper Cable

HP X140 40G CFP LC LR4 10km SM Transceiver











JH378A

JH379A

JH380A

JH381A

JH382A

JH383A

JC784C

JC857A

JD061A

JD062A

JD063B

JD089B

JD092B

JD093B

JD094B

JD095C

JD096C

JD097C

JG327A

JG328A

JG329A

JG330A

JG331A

JG661A

JG325B

JG709A

Page 31

QuickSpecs

Accessories


HP X130 10G XFP LC ZR Single Mode 80km 1550nm Transceiver

HP X130 10G XFP LC LR Single Mode 10km 1310nm Transceiver






HP X130 10G SFP+ LC LH 80km Transceiver


Power Supply

HP A58x0AF 650W AC Power Supply

HP 58x0AF 650W DC Power Supply

HP FlexFabric 5930-32QSFP+ Switch_PL (JG726A)

HP X711 Front (port side) to Back (power side) Airflow High Volume Fan Tray

HP X712 Back (power side) to Front (port side) Airflow High Volume Fan Tray

HP FlexFabric 5930-4Slot Switch (JH179A)

HP 5930 24-port SFP+ and 2-port QSFP+ Module

HP 5930 24-port SFP+ and 2-port QSFP+ with MACsec Module

HP 5930 24-port 10GBASE-T and 2-port QSFP+ with MACsec Module


HP 5930 24-port Converged Port and 2-port QSFP+ Module

HP 5930-4Slot Back (Power Side) to Front (Port Side) Airflow Fan Tray

HP 5930-4Slot Front (Port Side) to Back (Power Side) Airflow Fan Tray

HP FlexFabric 5930-2Slot+2QSFP+ Switch (JH178A)

HP 5930 24-port SFP+ and 2-port QSFP+ Module

HP 5930 24-port SFP+ and 2-port QSFP+ with MACsec Module

HP 5930 24-port 10GBASE-T and 2-port QSFP+ with MACsec Module


HP 5930 24-port Converged Port and 2-port QSFP+ Module

HP X711 Front (port side) to Back (power side) Airflow High Volume Fan Tray

HP X712 Back (power side) to Front (port side) Airflow High Volume Fan Tray


JG552A

JG553A

JH180A

JH181A

JH182A

JH183A

JH184A

JH185A

JH186A

JH180A

JH181A

JH182A

JH183A

JH184A

JG552A

JG553A

JD103A

JD107A

JD108B

JD118B

JD119B

JG081C

JG234A

JG234A

JG915A

JG326A

JC680A

JC681A

Page 32

QuickSpecs

Summary of Changes

Date

11-Dec-2015

12-Oct-2015

02-Oct-2015

28-Sep-2015

Version History Action

From Version 14 to 15 Changed

From Version 13 to 14 Added



12-Jun-2015

05-May-2015

24-Apr-2015

12-Dec-2014

03-Jul-2014

15-Apr-2014

19-Mar-2013

17-Dec-2013

11-Dec-2013

Changed




Changed

From Version 7 to 8 Removed







Description of Change

Updated Overview and Technical Specifications

Added new DC power supply:

JH336A

Configuration section updated

Bundles added:

JH378A

JH379A

JH380A

JH381A

JH382A

JH383A

Minor changes on Features and benefits, Configuration menu updated

Product images added, Configuration menu updated

Minor spelling change made on the overview section,

Configuration menu updated

Added two new models:

JH179A

JH178A

Updated Overview, Configuration, Technical Specifications and

Accessories sections

Deleted SKU JG325A

Configuration menu updated.

Transceivers were revised.

Transceivers were revised in Configuration.

Switch Enclosure Options were revised and HP X140 40G

QSFP+ LC LR4 SM XCVR was added to Configuration.

Updated the power specifications and accessories.

Page 33

QuickSpecs

Summary of Changes


Sign up for updates

Rate this document

© Copyright 2015 Hewlett Packard Enterprise Development LP. The information contained herein is subject to change without notice. The only warranties for Hewlett Packard Enterprise products and services are set forth in the express warranty statements accompanying such products and services.

Nothing herein should be construed as constituting an additional warranty. Hewlett Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.

To learn more, visit: http://www.hpe.com/networking c04111326 - 14818 - Worldwide - V15 - 11-December-2015

Page 34

HPE FlexFabric 5930 Switch Series

QuickSpecs

Related manuals

Hewlett Packard Enterprise

JH185A

Hewlett Packard Enterprise

JH184A

HPE

JH182A

Aruba

Comware-Based Devices Transceiver Modules

Hewlett Packard Enterprise

JH183A

Hewlett Packard Enterprise

JH182A

Aruba

JH213A