advertisement
Power over Ethernet Injector
User Guide
LP1001AE-R2
Rev.1.21
15-Feb-2007
Content
O VERVIEW ................................................................................................................1
F EATURES .................................................................................................................3
H ARDWARE D ESCRIPTION .........................................................................................3
P ACKAGE C ONTENTS ................................................................................................4
I NSTALLATION ..........................................................................................................4
Overview
The Power over Ethernet Injector provides data and AC power through the
Ethernet cable to PoE-equipped device, such as AP, PoE splitter or other equipment support IEEE 802.3af standard. The injector supports IEEE
802.3af standard that can detect the connected device, which support the
IEEE 802.3af and then provide the power to the device. If the injector detect the connected device does not support the IEEE 802.3af then the injector will not provide the power to the connected device. The injector is typically installed near the Ethernet hub. The following figures show the how Power over Ethernet Injector application.
Power over Ethernet Injection Application for non-PoE device
1
Power over Ethernet Injection Application for PoE device
2
Features
Power Over Ethernet Injector
Remote power feeding application
Short circuit protection
Mix Ethernet and power into RJ-45 port
Deliver power up to 100 meters
Light weight and compact size
Compatible with IEEE802.3af
Plug-and-Play
Hardware Description
The Power over Ethernet Injector has three connection ports and one LED indicator. We will describe each in following.
Data In port: It is a RJ-45 Ethernet interface port for data transmit into the PoE Injector. It is for connecting with the switch.
The Data In and Power in port figure
Power In port: The Power In port is for supplying the power into the
Injector.
Data Out port: It is a RJ-45 Ethernet port to connect with PoE Splitter, or PD.
Data Out port figure
3
Package Contents
One Power over Ethernet Injector
User Manual
Power cord x 1, 1830mm
The Power over Ethernet Injector User Guide
Figure 1-1. Package Contents
Compare the contents of your Power over Ethernet Injector package with the standard checklist above. IF any item is missing or damaged, please contact your local dealer for service.
Installation
To install the Power over Ethernet Injector, please follow the steps below.
1. Using RJ-45 cable that is Data in port on the Power over Ethernet
Injector to connect with the Switch/HUB.
2. Using RJ-45 cable that is on the Data out port in Power over Ethernet
Injector to connect with the PoE Splitter, PD (Such as Router, Access
Point…etc.) or PoE Hub.
3. Plug in the power cord of the Power over Ethernet Injector to the wall power plug.
4. Before starting, make sure all connections are correct.
The Power over Ethernet Injector connects to the Splitter, POE
Hub or PD is in Data Out port.
The Power over Ethernet Injector connects to the switch with
Data In port.
The Power In port is to get the power supply to Power over
Ethernet Injector from wall power plug.
4
Technical Specification
The following table provides the technical specification of the Power over
Ethernet Injector.
Standard
Connector
IEEE802.3 10BASE-T
IEEE802.3u 100BASE-TX
IEEE802.3af
RJ-45 Data in/out: Data/signal pairs pin
1,2,3,6
RJ-45 Power out: power over spare wire pairs pin: 4,5(V+) , 7,8(V-)
Network Cable
10BASE-T: 2-pair UTP/STP Cat.3, 4,5 cable
EIA/TIA-568 100-ohm (100m)
100BASE-TX: 2-pair UTP/STP Cat.5 cable
EIA/TIA-568 100-ohm (100m)
System: power (green) LED
Input Power Power supply: AC 100~240V, 50~60Hz, 0.3A
Output Power DC 48V, 0.3A
Operating Temperature 0 ℃~45℃
Operating Humidity 10%~90% Humidity (non-condensing)
Storage Temperature
Dimension
-40 ℃~70℃
117mm x 60mm x 35mm (W x D x H)
EMI & Safety FCC Class B, CE, UL, cUL, CE/EN60950
5
advertisement
Related manuals
advertisement