Alcatel-Lucent 7210 SAS D, E OS router Basic System Configuration Guide

7210 SAS D, E OS
Basic System Configuration Guide
Software Versions: 7210 SAS OS 3.0 Rev. 04
April 2011
Document Part Number: 93-0219-04-04
93-0219-04-04
This document is protected by copyright. Except as specifically permitted herein, no portion of the provided information can be
reproduced in any form, or by any means, without prior written permission from Alcatel-Lucent.
Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of Alcatel-Lucent. All other trademarks are the property of
their respective owners.
The information presented is subject to change without notice.
Alcatel-Lucent assumes no responsibility for inaccuracies contained herein.
Copyright 2011 Alcatel-Lucent. All rights reserved.
TABLE
OF
CONTENTS
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Getting Started
Alcatel-Lucent 7210 SAS-Series System Configuration Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
CLI Usage
CLI Structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Navigating in the CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
CLI Contexts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Basic CLI Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
CLI Environment Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
CLI Monitor Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Getting Help in the CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
The CLI Command Prompt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Displaying Configuration Contexts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
EXEC Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Entering CLI Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Command Completion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Unordered Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Editing Keystrokes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Absolute Paths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Entering Numerical Ranges. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Pipe/Match. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Redirection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Basic Command Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
File System Management
The File System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Compact Flash Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
URLs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Wildcards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
File Management Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
Modifying File Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
Creating Directories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Copying Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
Moving Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Removing Files and Deleting Directories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Displaying Directory and File Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
File Command Reference. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Boot Options
System Intialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
Manual Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
Auto Init . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
7210 SAS D, E OS Basic System Configuration Guide
Page 3
Table of Contents
Out-of-band (OOB) Ethernet Management Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
Configuration and Image Loading. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
Ping Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
Persistence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
Initial System Startup Process Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108
Configuration Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109
Configuring Boot File Options with CLI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
BOF Configuration Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
Basic BOF Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
Common Configuration Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
Searching for the BOF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116
Accessing the CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
Console Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
Configuring BOF Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121
Service Management Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
System Administration Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
Viewing the Current Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
Modifying and Saving a Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124
Deleting BOF Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125
Saving a Configuration to a Different Filename . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127
Rebooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127
BOF Command Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129
System Management
System Management Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156
System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156
System Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156
System Contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .156
System Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157
System Coordinates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157
Naming Objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157
Common Language Location Identifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .158
System Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159
Time Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159
Network Time Protocol (NTP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .161
SNTP Time Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .162
CRON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .163
High Availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .164
HA Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .164
Redundancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .164
Temperature Threshold Alarm and Fan Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .166
Link Layer Discovery Protocol (LLDP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .167
System Configuration Process Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171
Configuration Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .172
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .172
Configuring System Management with CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .173
System Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .174
Saving Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .174
Basic System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .175
Page 4
7210 SAS D, E OS Basic System Configuration Guide
Table of Contents
Common Configuration Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .176
System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .177
System Information Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .178
Coordinates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180
System Time Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .181
Configuring Backup Copies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .202
System Administration Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .203
Validating the Golden Bootstrap Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .203
Updating the Golden Bootstrap Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .204
Disconnect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .204
Set-time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .205
Display-config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .205
Tech-support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .207
Save . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .207
Reboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .208
Post-Boot Configuration Extension Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .209
Configuring System Monitoring Thresholds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .212
Creating Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .212
System Alarm Contact Inputs in 7210 SAS-E devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .214
Configuring LLDP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .215
Standards and Protocol Support (7210 SAS D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .319
Standards and Protocol Support (7210 SAS E). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .321
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .323
7210 SAS D, E OS Basic System Configuration Guide
Page 5
Table of Contents
Page 6
7210 SAS D, E OS Basic System Configuration Guide
LIST
OF
TABLES
Getting Started
Table 1:
Configuration Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
CLI Usage
Table 2:
Table 3:
Table 4:
Table 5:
Table 6:
Table 7:
Table 8:
Table 9:
Table 10:
Table 11:
Console Control Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Command Syntax Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
CLI Environment Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
CLI Monitor Command Contexts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Online Help Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Command Editing Keystrokes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
CLI Range Use Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Regular Expression Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Special Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Show Alias Output Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
File System Management
Table 12:
Table 13:
URL Types and Syntax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
File Command Local and Remote File System Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Boot Options
Table 14:
Table 15:
Table 16:
Console Configuration Parameter Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
Show BOF Output Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .149
Show BOF Output Fields (supported only on 7210 SAS-E) . . . . . . . . . . . . . . . . . . . . . . . . . . .150
System Management
Table 17:
Table 18:
Table 19:
Table 20:
Table 21:
Table 22:
Table 23:
Table 24:
Table 25:
Table 26:
System-defined Time Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159
Temperature Thresholds for 7210 SAS-D Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .166
System-defined Time Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .182
Show System CPU Output Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .285
Show Memory Pool Output Fields. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .295
Show System SNTP Output Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .300
Show System Time Output Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .304
Show System tod-suite Output Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .306
Show System Time-range Output Fields. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .309
System Timing Output Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .310
7210 SAS D, E OS Basic System Configuration Guide
Page 7
List of Tables
Page 8
7210 SAS D, E OS Basic System Configuration Guide
LIST
OF
FIGURES
CLI Usage
Figure 1:
Figure 2:
Root Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Operational Root Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Boot Options
Figure 3:
Figure 4:
Figure 5:
Figure 6:
Figure 7:
Figure 8:
Figure 9:
Figure 10:
Bootstrap Load Process - System Initialisation - Part I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97
Files on the Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
Bootstrap Process - System Initialization - Part II-A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
Bootstrap Process - System Initialization - Part II-B. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103
Bootstrap Process - System Initialization - Part II-C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104
Timos Boot - System Initialization - Part III . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
7210 SAS E Front Panel Console Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
7210 SAS D Front Panel Console Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
System Management
Figure 11:
Figure 12:
Figure 13:
LLDP Internal Architecture for a Network Node . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .169
Customer Use Example For LLDP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .170
System Configuration and Implementation Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171
7210 SAS D, E OS Basic System Configuration Guide
Page 9
List of Figures
Page 10
7210 SAS D, E OS Basic System Configura-
Preface
About This Guide
This guide describes system concepts and provides configuration explanations and examples
to configure 7210 SAS-Series boot option file (BOF), file system and system management
functions.
This document is organized into functional chapters and provides concepts and descriptions of
the implementation flow, as well as Command Line Interface (CLI) syntax and command
usage.
Audience
This manual is intended for network administrators who are responsible for configuring the
7210 SAS-Series routers. It is assumed that the network administrators have an understanding
of networking principles and configurations. Protocols, standards, and processes described in
this manual include the following:
•
CLI concepts
•
File system concepts
•
Boot option, configuration, image loading, and initialization procedures
•
Basic system management functions such as the system name, router location and
coordinates, and CLLI code, time zones, Network Time Protocol (NTP), Simple
Network Time Protocol (SNTP), and synchronization properties
7210 SAS D, E OS Basic System Configuration Guide
Page 11
Preface
List of Technical Publications
The 7210-SAS D, E OS documentation set is composed of the following books:
•
7210-SAS D, E OS Basic System Configuration Guide
This guide describes basic system configurations and operations.
•
7210-SAS D, E OS System Management Guide
This guide describes system security and access configurations as well as event
logging and accounting logs.
•
7210-SAS D, E OS Interface Configuration Guide
This guide describes card, Media Dependent Adapter (MDA), and port provisioning.
•
7210-SAS D, E OS Router Configuration Guide
This guide describes logical IP routing interfaces and associated attributes such as an
IP address, port, link aggregation group (LAG) as well as IP-based filtering.
•
7210-SAS D, E OS Routing Protocols Guide
This guide provides an overview of routing concepts and provides configuration
examples for protocols and route policies.
•
7210-SAS D, E OS Services Guide
This guide describes how to configure service parameters such as customer
information, and user services.
•
7210-SAS D, E OS OAM and Diagnostic Guide
This guide describes how to configure features such as service mirroring and
Operations, Administration and Management (OAM) tools.
•
7210-SAS D, E OS Quality of Service Guide
This guide describes how to configure Quality of Service (QoS) policy management.
Page 12
7210 SAS D, E OS Basic System Configuration Guide
Preface
Technical Support
If you purchased a service agreement for your 7210 SAS-Series router and related products from a
distributor or authorized reseller, contact the technical support staff for that distributor or reseller
for assistance. If you purchased an Alcatel-Lucent service agreement, contact your welcome
center:
Web:
http://www1.alcatel-lucent.com/comps/pages/carrier_support.jhtml
7210 SAS D, E OS Basic System Configuration Guide
Page 13
Preface
Page 14
7210 SAS D, E OS Basic System Configuration Guide
Getting Started
In This Chapter
This chapter provides process flow information to configure basic router and system parameters,
perform operational functions with directory and file management, and boot option tasks.
Alcatel-Lucent 7210 SAS-Series System Configuration Process
Table 1 lists the tasks necessary to configure boot option files (BOF) and system and file
management functions. Each chapter in this book is presented in an overall logical configuration
flow. Each section describes a software area and provides CLI syntax and command usage to
configure parameters for a functional area. After the hardware installation has been properly
completed, proceed with the 7210 SAS-Series device configuration tasks in the following order:
Table 1: Configuration Process
Area
CLI Usage
Operational functions
Task
Chapter
The CLI structure
CLI Usage on page 17
Basic CLI commands
Basic CLI Commands on page 22
Configure environment commands
CLI Environment Commands on page 25
Configure monitor commands
CLI Monitor Commands on page 26
Directory and file management
File System Management on page 77
7210 SAS D, E OS Basic System Configuration Guide
Page 15
Getting Started
Table 1: Configuration Process
Area
Task
Chapter (Continued)
Boot options
Configure boot option files
(BOF)
Boot Options on page 95
System configuration
Configure system functions,
including host name, address,
domain name, and time
parameters.
System Management on page 155
Reference
List of IEEE, IETF, and other
proprietary entities.
Standards and Protocol Support on page 201
Page 16
7210 SAS D, E OS Basic System Configuration Guide
CLI Usage
In This Chapter
This chapter provides information about using the command-line interface (CLI).
Topics in this chapter include:
•
CLI Structure on page 18
•
Navigating in the CLI on page 20
•
Basic CLI Commands on page 22
•
CLI Environment Commands on page 25
•
CLI Monitor Commands on page 26
•
Getting Help in the CLI on page 27
•
The CLI Command Prompt on page 29
•
Displaying Configuration Contexts on page 30
•
EXEC Files on page 33
•
Entering CLI Commands on page 34
7210 SAS D, E OS Basic System Configuration Guide
Page 17
CLI Structure
CLI Structure
Alcatel-Lucent’s Operating System (OS) CLI is a command-driven interface accessible through
the console, Telnet and secure shell (SSH). The CLI can be used for configuration and
management of routers.
The CLI command tree is a hierarchical inverted tree. At the highest level is the ROOT level.
Below this level are other tree levels with the major command groups; for example, configuration
commands and show commands are levels below ROOT.
The CLI is organized so related commands with the same scope are at the same level or in the
same context. Sublevels or subcontexts have related commands with a more refined scope.
ROOT
ADMIN
BOF
CONFIGURE
ENVIRONMENT
alias
create
more
reduced-prompt
saved-ind-prompt
terminal
time-display
FILE
MONITOR
filter
lag
port
qos
router
service
PASSWORD
HELP
attrib
cd
copy
delete
dir
format
md
move
rd
scp
type
version
card
cron
dot1ag
filter
lag
log
mirror
port
qos
router
saa
service
split-horizon-group
system
address
autonegotiate
console-speed
dns-domain
duplex
persist
primary-config
primary-dns
primary-image
save
secondary-config
secondary-dns
secondary-image
ping-address
tertiary-config
static-route
tertiary-dns
tertiary-image
uplinkA-address
uplinkA-port
uplinkA-route
uplinkA-vlan
uplinkB-address
uplinkB-port
wait
check-golden-bootstrap
debug-save
disconnect
display-config
radius-disc
reboot
save
set-time
update-golden-bootstrap
help
help edit
help globals
Figure 1: Root Commands
Page 18
7210 SAS D, E OS Basic System Configuration Guide
CLI Usage
ROOT
SHOW
CLEAR
DEBUG
TOOLS
dump
perform
lag
mirror-source
radius
router
service
snmp
system
trace
card
cron
filter
lag
log
port
qos
radius
router
saa
screen
service
tacplus
trace
alias
bof
boot-messages
card
chassis
cron
debug
dot1ag
filter
lag
log
mda
mirror
pools
port
port-tree
qos
router
saa
service
snmp
split-horizon-group
system
time
trace
uptime
users
version
Figure 2: Operational Root Commands
7210 SAS D, E OS Basic System Configuration Guide
Page 19
Navigating in the CLI
Navigating in the CLI
The following sections describe additional navigational and syntax information.
•
CLI Contexts on page 20
•
Basic CLI Commands on page 22
•
CLI Environment Commands on page 25
•
CLI Monitor Commands on page 26
•
Entering Numerical Ranges on page 39
CLI Contexts
Use the CLI to access, configure, and manage Alcatel-Lucent’s 7210 SAS devices. CLI
commands are entered at the command line prompt. Access to specific CLI commands is
controlled by the permissions set by your system administrator. Entering a CLI command makes
navigation possible from one command context (or level) to another.
When you initially enter a CLI session, you are in the ROOT context. Navigate to another level by
entering the name of successively lower contexts. For example, enter either the configure or show
commands at the ROOT context to navigate to the config or show context, respectively. For
example, at the command prompt, enter config. The active context displays in the command
prompt.
A:ALU-7210# config
A:ALU-7210>config#
In a given CLI context, you can enter commands at that context level by simply entering the text.
It is also possible to include a command in a lower context as long as the command is formatted in
the proper command and parameter syntax.
The following example shows two methods to navigate to a service SAP ingress level:
Method 1:
A:ALU-7210# config service epipe 6 sap 1/1/2 ingress
Method 2:
A:ALU-7210# configure
A:ALU-7210>config# service
A:ALU-7210>config>service# epipe 6
A:ALU-7210>config>service>epipe# sap 1/1/2
A:ALU-7210>config>service>epipe>sap# ingress
A:ALU-7210>config>service>epipe>sap>ingress#
Page 20
7210 SAS D, E OS Basic System Configuration Guide
CLI Usage
The CLI returns an error message when the syntax is incorrect.
A:ALU-7210>config>service>epipe# sapp
^
Error: Bad command.
A:ALU-7210>config>service>epipe#
7210 SAS D, E OS Basic System Configuration Guide
Page 21
Navigating in the CLI
Basic CLI Commands
The console control commands are the commands that are used for navigating within the CLI and
displaying information about the console session. Most of these commands are implemented as
global commands. They can be entered at any level in the CLI hierarchy with the exception of the
password command which must be entered at the ROOT level. The console control commands
are listed in Table 2.
Table 2: Console Control Commands
Command
Page 22
Description
Page
<Ctrl-c>
Aborts the pending command.
<Ctrl-z>
Terminates the pending command line and returns to the ROOT
context.
back
Navigates the user to the parent context.
48
clear
Clears statistics for a specified entity or clears and resets the entity.
48
echo
Echos the text that is typed in. Primary use is to display messages to
the screen within an exec file.
49
exec
Executes the contents of a text file as if they were CLI commands
entered at the console.
49
exit
Returns the user to the previous higher context.
49
exit all
Returns the user to the ROOT context.
50
help
?
Displays help in the CLI.
50
history
Displays a list of the most recently entered commands.
52
info
Displays the running configuration for a configuration context.
52
logout
Terminates the CLI session.
56
oam
Provides OAM test suite options. See the OAM section of the 7210
SAS OS OAM and Diagnostic Guide.
password
Changes the user CLI login password. The password can only be
changed at the ROOT level.
57
ping
Verifies the reachability of a remote host.
57
pwc
Displays the present or previous working context of the CLI session.
59
7210 SAS D, E OS Basic System Configuration Guide
CLI Usage
Table 2: Console Control Commands (Continued)
Command
Description
Page
sleep
Causes the console session to pause operation (sleep) for one second
or for the specified number of seconds. Primary use is to introduce a
pause within the execution of an exec file.
59
ssh
Opens a secure shell connection to a host.
60
telnet
Telnet to a host.
60
traceroute
Determines the route to a destination address.
61
tree
Displays a list of all commands at the current level and all sublevels.
62
write
Sends a console message to a specific user or to all users with active
console sessions.
62
The list of all system global commands is displayed by entering help globals in the CLI. For
example:
A:ALU-7210>config>service# help globals
back
- Go back a level in the command tree
echo
- Echo the text that is typed in
enable-admin
- Enable the user to become a system administrator
exec
- Execute a file - use -echo to show the commands and
prompts on the screen
exit
- Exit to intermediate mode - use option all to exit to
root prompt
help
- Display help
history
- Show command history
info
- Display configuration for the present node
logout
- Log off this system
oam
+ OAM Test Suite
ping
- Verify the reachability of a remote host
pwc
- Show the present working context
sleep
- Sleep for specified number of seconds
ssh
- SSH to a host
telnet
- Telnet to a host
traceroute
- Determine the route to a destination address
tree
- Display command tree structure from the context of
execution
write
- Write text to another user
A:ALU-7210>config>service#
7210 SAS D, E OS Basic System Configuration Guide
Page 23
Navigating in the CLI
Table 3 lists describes command syntax symbols.
Table 3: Command Syntax Symbols
Symbol
Description
|
A vertical line indicates that one of the parameters within the brackets or braces is
required.
tcp-ack {true|false}
[ ]
Brackets indicate optional parameters.
redirects [number seconds]
< >
Angle brackets indicate that you must enter text based on the parameter inside the
brackets.
interface <interface-name>
{ }
Braces indicate that one of the parameters must be selected.
default-action {drop|forward}
[{ }]
Braces within square brackets indicates that you must choose one of the optional
parameters.
• sdp sdp-id [{gre|mpls}]vpls service-id [svc-sap-type {nullstar|dot1q|dot1q-preserve}]
Page 24
Bold
Commands in bold indicate commands and keywords.
Italic
Commands in italics indicate command options.
7210 SAS D, E OS Basic System Configuration Guide
CLI Usage
CLI Environment Commands
The CLI environment commands are found in the root>environment context of the CLI tree
and controls session preferences for a single CLI session. The CLI environment commands are
listed in Table 4.
Table 4: CLI Environment Commands
Command
Description
Page
alias
Enables the substitution of a command line by an alias.
63
create
Enables or disables the use of a create parameter check.
63
more
Configures whether CLI output should be displayed one screen
at a time awaiting user input to continue.
63
reduced-prompt
Configures the maximum number of higher-level CLI context
nodes to display by name in the CLI prompt for the current CLI
session.
64
saved-indprompt
Saves the indicator in the prompt.
64
terminal
Configures the terminal screen length for the current CLI
session.
65
time-display
Specifies whether time should be displayed in local time or
UTC.
65
7210 SAS D, E OS Basic System Configuration Guide
Page 25
Navigating in the CLI
CLI Monitor Commands
Monitor commands display specified statistical information related to the monitor subject (such as
filter, port, QoS, router, service) at a configurable interval until a count is reached. The CLI
monitor commands are found in the root>monitor context of the CLI tree.
The monitor command output displays a snapshot of the current statistics. The output display
refreshes with subsequent statistical information at each configured interval and is displayed as a
delta to the previous display.
The <Ctrl-c> keystroke interrupts a monitoring process. Monitor command configurations
cannot be saved. You must enter the command for each monitoring session. Note that if the
maximum limits are configured, you can monitor the statistical information for a maximum of 60
* 999 sec ~ 1000 minutes.
The CLI monitor command contexts are listed in Table 4.
Table 5: CLI Monitor Command Contexts
Command
Page 26
Description
Page
filter
Enables IP and MAC filter monitoring at a configurable interval
until that count is reached.
66
lag
Enables Link Aggregation Group (LAG) monitoring to display
statistics for individual port members and the LAG.
69
port
Enables port traffic monitoring. The specified port(s) statistical
information displays at the configured interval until the
configured count is reached.
71
service
Monitors commands for a particular service.
73
7210 SAS D, E OS Basic System Configuration Guide
CLI Usage
Getting Help in the CLI
The help system commands and the ? key display different types of help in the CLI. Table 6 lists
the different help commands.
Table 6: Online Help Commands
Command
Description
help ?
List all commands in the current context.
string ?
List all commands available in the current context that start with string.
command ?
Displays the command’s syntax and associated keywords.
command keyword ?
List the associated arguments for keyword in command.
string<Tab>
Complete a partial command name (auto-completion) or list available
commands that match string.
The tree and tree detail system commands are help commands useful when searching for a
command in a lower-level context.
The following example displays a partial list of the tree and tree detail command output
entered at the config level.
7210 SAS D, E OS Basic System Configuration Guide
Page 27
Getting Help in the CLI
A:ALU-7210>config# tree
configure
+---card
| +---card-type
| +---mda
| | +---access
| | +---mda-type
| | +---network
| | +---shutdown
| +---shutdown
+---cron
| +---action
| | +---expire-time
| | +---lifetime
| | +---max-completed
| | +---results
| | +---script
| | +---shutdown
| +---schedule
| | +---action
| | +---count
| | +---day-of-month
| | +---description
| | +---end-time
| | +---hour
| | +---interval
| | +---minute
| | +---month
| | +---shutdown
| | +---type
| | +---weekday
| +---script
| | +---description
| | +---location
| | +---shutdown
| +---time-range
| | +---absolute
| | +---daily
| | +---description
| | +---weekdays
| | +---weekend
| | +---weekly
| +---tod-suite
| | +---description
| | +---egress
| | | +---filter
| | | +---qos
| | | +---scheduler-policy
| | +---ingress
| | | +---filter
| | | +---qos
| | | +---scheduler-policy
+---dot1ag
| +---domain
| | +---association
...
Page 28
*A:ALA-12>config# tree detail
configure
+---card <slot-number>
| no card <slot-number>
| +---card-type <card-type>
| | no card-type
| +---mda <mda-slot>
| | no mda <mda-slot>
| | +---access
| | +---mda-type <mda-type>
| | | no mda-type
| | +---network
| | +---no shutdown
| | | shutdown
| +---no shutdown
| | shutdown
+---cron
| +---action <action-name> [owner <action-owner>]
| | no action <action-name> [owner <action-owner>]
| | +---expire-time {<seconds>|forever}
| | +---lifetime {<seconds>|forever}
| | +---max-completed <unsigned>
| | +---no results
| | | results <file-url>
| | +---no script
| | | script <script-name> [owner <script-owner>]
| | +---no shutdown
| | | shutdown
| +---no schedule <schedule-name> [owner <schedule-owner>]
| | schedule <schedule-name> [owner <schedule-owner>]
| | +---action <action-name> [owner <action-owner>]
| | | no action
| | +---count <number>
| | | no count
| | +---day-of-month {<day-number> [..<day-number>]|all}
| | | no day-of-month
| | +---description <description-string>
| | | no description
| | +---end-time [<date>|<day-name>] <time>
| | | no end-time
| | +---hour {<hour-number> [..<hour-number>]|all}
| | | no hour
| | +---interval <seconds>
| | | no interval
| | +---minute {<minute-number> [..<minute-number>]|all}
| | | no minute
|
|
+---month {<month-number> [..<month-number>]|<month-name>
[..<month-nam>]|all}
| | | no month
| | +---no shutdown
| | | shutdown
| | +---type <schedule-type>
| | +---weekday {<weekday-number> [..<weekday-number>]|<day-name>
[..<day-nme>]|all}
|...
7210 SAS D, E OS Basic System Configuration Guide
CLI Usage
The CLI Command Prompt
By default, the CLI command prompt indicates the device being accessed and the current CLI
context. For example, the prompt: A:ALA-1>config>router>if# indicates the active context, the
user is on the device with hostname ALA-1 in the configure>router>interface context. In the
prompt, the separator used between contexts is the “>” symbol.
At the end of the prompt, there is either a pound sign (“#”) or a dollar sign (“$”). A “#” at the end
of the prompt indicates the context is an existing context. A “$” at the end of the prompt indicates
the context has been newly created. New contexts are newly created for logical entities when the
user first navigates into the context.
Since there can be a large number of sublevels in the CLI, the environment command reducedprompt no of nodes in prompt allows the user to control the number of levels displayed in the
prompt.
All special characters (#, $, etc.) must be enclosed within double quotes, otherwise it is seen as a
comment character and all characters on the command line following the # are ignored.
For example:
*A:ALU-7210>config>router# interface "primary#1"
When changes are made to the configuration file a “*” appears in the prompt string (*A:ALU7210) indicating that the changes have not been saved. When an admin save command is
executed the “*” disappears. This behavior is controlled in the saved-ind-prompt command in the
environment context.
7210 SAS D, E OS Basic System Configuration Guide
Page 29
Displaying Configuration Contexts
Displaying Configuration Contexts
The info and info detail commands display configuration for the current level. The info
command displays non-default configurations. The info detail command displays the entire
configuration for the current level, including defaults. The following example shows the output
that displays using the info command and the output that displays using the info detail
command.
*A:ALA>config>service>vpls# info
---------------------------------------------stp
shutdown
exit
sap 1/1/14:100 create
exit
sap 1/1/15:100 create
exit
no shutdown
---------------------------------------------*A:ALA>config>service>vpls# info detail
---------------------------------------------no description
no disable-learning
no disable-aging
no discard-unknown
fdb-table-size 250
fdb-table-high-wmark 95
fdb-table-low-wmark 90
local-age 300
stp
shutdown
priority 32768
hello-time 2
forward-delay 15
max-age 20
hold-count 6
mode rstp
exit
mac-move
move-frequency 2
retry-timeout 10
shutdown
exit
sap 1/1/14:100 create
no description
no tod-suite
limit-mac-move blockable
no disable-aging
no max-nbr-mac-addr
no discard-unknown-source
no mac-pinning
stp
path-cost 10
priority 128
no edge-port
auto-edge
Page 30
7210 SAS D, E OS Basic System Configuration Guide
CLI Usage
link-type pt-pt
no root-guard
no shutdown
exit
dot1ag
exit
no authentication-policy
no l2pt-termination
no bpdu-translation
ingress
qos 1
no match-qinq-dot1p
no filter
exit
egress
no qinq-mark-top-only
no filter
no agg-rate-limit
exit
no collect-stats
no accounting-policy
no shutdown
exit
sap 1/1/15:100 create
no description
no tod-suite
limit-mac-move blockable
no disable-aging
no max-nbr-mac-addr
no discard-unknown-source
no mac-pinning
stp
path-cost 10
priority 128
no edge-port
auto-edge
link-type pt-pt
no root-guard
no shutdown
exit
dot1ag
exit
no authentication-policy
no l2pt-termination
no bpdu-translation
ingress
qos 1
no match-qinq-dot1p
no filter
exit
egress
no qinq-mark-top-only
no filter
no agg-rate-limit
exit
no collect-stats
no accounting-policy
no shutdown
exit
7210 SAS D, E OS Basic System Configuration Guide
Page 31
Displaying Configuration Contexts
no shutdown
---------------------------------------------*A:ALA>config>service>vpls#
Page 32
7210 SAS D, E OS Basic System Configuration Guide
CLI Usage
EXEC Files
The exec command allows you to execute a text file of CLI commands as if it were typed at a
console device.
The exec command and the associated exec files can be used to conveniently execute a number of
commands that are always executed together in the same order. For example, an exec command
can be used by a user to define a set of commonly used standard command aliases.
The echo command can be used within an exec command file to display messages on screen
while the file executes.
7210 SAS D, E OS Basic System Configuration Guide
Page 33
Entering CLI Commands
Entering CLI Commands
Command Completion
The CLI supports both command abbreviation and command completion. If the keystrokes
entered are enough to match a valid command, the CLI displays the remainder of the command
syntax when the <Tab> key or space bar is pressed. When typing a command, the <Tab> key or
space bar invokes auto-completion. If the keystrokes entered are definite, auto-completion will
complete the command. If the letters are not sufficient to identify a specific command, pressing
the <Tab> key or space bar will display commands matching the letters entered.
System commands are available in all CLI context levels.
Unordered Parameters
In a given context, the CLI accepts command parameters in any order as long as the command is
formatted in the proper command keyword and parameter syntax. Command completion will still
work as long as enough recognizable characters of the command are entered.
The following output shows different static-route command syntax and an example of the
command usage.
*A:ALA-1>config>router# static-route
- [no] static-route {<ip-prefix/prefix-length>|<ip-prefix> <netmask>}
[preference <preference>] [metric <metric>] [enable|disable] next-hop
<gateway>
- [no] static-route {<ip-prefix/prefix-length>|<ip-prefix> <netmask>}
[preference <preference>] [metric <metric>] [enable|disable] black-hole
Page 34
7210 SAS D, E OS Basic System Configuration Guide
CLI Usage
Editing Keystrokes
When entering a command, special keystrokes allow for editing of the command. Table 7 lists the
command editing keystrokes.
Table 7: Command Editing Keystrokes
Editing Action
Keystrokes
Delete current character
<Ctrl-d>
Delete text up to cursor
<Ctrl-u>
Delete text after cursor
<Ctrl-k>
Move to beginning of line
<Ctrl-a>
Move to end of line
<Ctrl-e>
Get prior command from history
<Ctrl-p>
Get next command from history
<Ctrl-n>
Move cursor left
<Ctrl-b>
Move cursor right
<Ctrl-f>
Move back one word
<Esc><b>
Move forward one word
<Esc><f>
Convert rest of word to uppercase
<Esc><c>
Convert rest of word to lowercase
<Esc><l>
Delete remainder of word
<Esc><d>
Delete word up to cursor
<Ctrl-w>
Transpose current and previous character
<Ctrl-t>
Enter command and return to root prompt
<Ctrl-z>
Refresh input line
<Ctrl-l>
7210 SAS D, E OS Basic System Configuration Guide
Page 35
Entering CLI Commands
Absolute Paths
CLI commands can be executed in any context by specifying the full path from the CLI root. To
execute an out-of-context command enter a forward slash “/” or backward slash “\” at the
beginning of the command line. The forward slash “/” or backward slash “\” cannot be used with
the environment alias command.The commands are interpreted as absolute path. Spaces between
the slash and the first command will return an error. Commands that are already global (such as
ping, telnet, exit, back, etc.) cannot be executed with a forward slash “/” or backward slash “\” at
the beginning of the command line.
*A:ALA-12# configure router
*A:ALA-12>config>router# interface system address 1.2.3.4
*A:ALA-12>config>router# /admin save
*A:ALA-12>config>router# \clear router interface
*A:ALA-12>config>router#
The command may or may not change the current context depending on whether or not it is a leaf
command. This is the same behavior the CLI performs when CLI commands are entered
individually, for example:
*A:ALA-12# admin
*A:ALA-12>admin# save
or
*A:ALA-12# admin save
*A:ALA-12#
Note that an absolute path command behaves the same as manually entering a series of command
line instructions and parameters.
For example, beginning in an IES context service ID 4 (IES 4),
CLI Syntax: config>service>ies> /clear card 1
behaves the same as the following series of commands.
Example: config>service>ies>exit all
clear card 1
configure service ies 4 (returns you to your starting point)
config>service>ies
Page 36
7210 SAS D, E OS Basic System Configuration Guide
CLI Usage
If the command takes you to a different context, the following occurs:
CLI Syntax: config>service>ies>/configure service ies 5 create
becomes
Example:
config>service>ies>exit all
configure service vpls 5 create
config>service>vpls>
7210 SAS D, E OS Basic System Configuration Guide
Page 37
Entering CLI Commands
History
The CLI maintains a history of the most recently entered commands. The history command
displays the most recently entered CLI commands.
*A:ALA-1# history
1 environment terminal length 48
2 environment no create
3 show version
4 configure port 1/1/1
5 info
6 \configure router isis
7 \port 1/1/1
8 con port 1/1/1
9 \con port 1/1/1
10 \configure router bgp
11 info
12 \configure system login-control
13 info
14 history
15 show version
16 history
*A:ALA-1# !3
A:cses-E11# show version
TiMOS-B-0.0.I2838 both/i386 ALCATEL SR 7750 Copyright (c) 2000-2011 Alcatel-Lucent.
All rights reserved. All use subject to applicable license agreements.
Built on Mon Jan 10 18:33:16 PST 2011 by builder in /rel0.0/I2838/panos/main
A:cses-E11#
TiMOS-B-0.0.I232 both/i386 ALCATEL SAS-E 7210 Copyright (c) 2000-2008 Alcatel-Lu
cent.
All rights reserved. All use subject to applicable license agreements.
Built on Sat Oct 11 18:15:40 IST 2008 by panosbld in /panosbld/ws/panos/main
*A:ALU-7210#
Page 38
7210 SAS D, E OS Basic System Configuration Guide
CLI Usage
Entering Numerical Ranges
The 7210-SAS OS CLI allows the use of a single numerical range as an argument in the command
line. A range in a CLI command is limited to positive integers and is denoted with two numbers
enclosed in square brackets with two periods (“..”) between the numbers:
[ x..y ]
where x and y are positive integers and y-x is less than 1000.
For example, it is possible to shut down ports 1 through 10 in Slot 1 on MDA 1. A port is denoted
with “slot/mda/port”, where slot is the slot number, mda is the MDA number and port is the port
number. To shut down ports 1 through 10 on Slot 1 and MDA 1, the command is entered as
follows:
configure port 1/1/[1..10] shutdown
<Ctrl-C> can be used to abort the execution of a range command.
Specifying a range in the CLI does have limitations. These limitations are summarized in Table 8.
Table 8: CLI Range Use Limitations
Limitation
Only a single range can be specified.
Description
It is not possible to shut down ports 1 through 10 on MDA 1 and MDA
2, as the command would look like
configure port 1/[1..2]/[1..10]
and requires two ranges in the command, [1..2] for the MDA and
[1..10] for the port number.
Ranges within quotation marks are
interpreted literally.
In the CLI, enclosing a string in quotation marks (“string”) causes the
string to be treated literally and as a single parameter. For example,
several commands in the CLI allow the configuration of a descriptive
string. If the string is more than one word and includes spaces, it must
be enclosed in quotation marks. A range that is enclosed in quotes is
also treated literally. For example,
configure router interface "A[1..10]" no shutdown
creates a single router interface with the name “A[1..10]”. However, a
command such as:
configure router interface A[1..10] no shutdown
creates 10 interfaces with names A1, A2 .. A10.
7210 SAS D, E OS Basic System Configuration Guide
Page 39
Entering CLI Commands
Table 8: CLI Range Use Limitations (Continued)
Limitation
The range cannot cause a change in
contexts.
Description
Commands should be formed in such a way that there is no context
change upon command completion. For example,
configure port 1/1/[1..10]
will attempt to change ten different contexts. When a range is specified
in the CLI, the commands are executed in a loop. On the first loop
execution, the command changes contexts, but the new context is no
longer valid for the second iteration of the range loop. A “Bad
Command” error is reported and the command aborts.
Command completion may cease to
work when entering a range.
Page 40
After entering a range in a CLI command, command and key
completion, which normally occurs by pressing the <Tab> or spacebar,
may cease to work. If the command line entered is correct and
unambiguous, the command works properly; otherwise, an error is
returned.
7210 SAS D, E OS Basic System Configuration Guide
CLI Usage
Pipe/Match
The 7210-SAS OS supports the pipe feature to search one or more files for a given character string
or pattern.
Note: When using the pipe/match command the variables and attributes must be spelled correctly.
The attributes following the command and must come before the expression/pattern. The
following displays examples of the pipe/match command to complete different tasks:
•
Task: Capture all the lines that include “echo” and redirect the output to a file on the
compact flash:
admin display-config | match “echo” > cf3cf1:\echo_list.txt
•
Task: Display all the lines that do not include “echo”:
admin display-config | match invert-match “echo”
•
Task: Display the first match of “vpls” in the configuration file:
admin display-config | match max-count 1 “vpls”
•
Task: Display everything in the configuration after finding the first instance of “interface”:
admin display-config | match post-lines 999999 interface
Command syntax:
match pattern context {parents | children | all} [ignore-case] [max-count lines-count]
[expression]
match pattern [ignore-case] [invert-match] [pre-lines pre-lines] [post-lines lines-count] [maxcount lines-count] [expression]
where:
pattern
context
parents
children
all
ignore-case
max-count
lines-count
expression
invert-match
pre-lines
pre-lines
post-lines
string or regular
keyword: display
keyword: display
keyword: display
keyword: display
keyword
keyword: display
1 — 2147483647
keyword: pattern
keyword
keyword: display
0 — 100
keyword: display
lines-count
1 — 2147483647
expression
context associated with the matching line
parent context information
child context information
both parent and child context information
only a specific number of instances of matching lines
is interpreted as a regular expression
some lines prior to the matching line
some lines after the matching line
For example:
7210 SAS D, E OS Basic System Configuration Guide
Page 41
Entering CLI Commands
*A:Dut-G# show log log-id 99 | match ignore-case sap
"Processing of an access port state change event is finished and the status of all affected
SAPs on port 1/1/21 has been updated."
"Service Id 4001, SAP Id 1/1/21:0.* configuration modified"
A:Dut-C# show log log-id 98 | match max-count 1 "service 1001"
"Status of service 1001 (customer 1) changed to administrative state: up, operational
state: up"
*A:Dut-G# admin display-config | match post-lines 4 max-count 2 expression "vpls"
#-------------------------------------------------...
vpls 1 customer 1 svc-sap-type null-star create
description "Default tls description for service id 1"
stp
shutdown
exit
vpls 2 customer 1 svc-sap-type null-star create
description "Default tls description for service id 2"
stp
shutdown
exit
...
#--------------------------------------------------
Table 9 describes regular expression symbols and interpretation (similar to what is used for route
policy regexp matching). Table 10 describes special characters.
Table 9: Regular Expression Symbols
String
Page 42
Description
.
Matches any single character.
[ ]
Matches a single character that is contained within the brackets.
[abc] matches “a”, “b”, or “c”. [a-z] matches any lowercase letter.
[A-Z] matches any uppercase letter.
[0-9] matches any number.
[^ ]
Matches a single character that is not contained within the brackets.
[^abc] matches any character other than “a”, “b”, or “c”.
[^a-z] matches any single character that is not a lowercase letter.
^
Matches the start of the line (or any line, when applied in multiline mode)
$
Matches the end of the line (or any line, when applied in multiline mode)
()
Define a “marked subexpression”.
Every matched instance will be available to the next command as a variable.
*
A single character expression followed by “*” matches zero or more copies of the
expression.
7210 SAS D, E OS Basic System Configuration Guide
CLI Usage
Table 9: Regular Expression Symbols (Continued)
String
Description
{m,n}
Matches least m and at most n repetitions of the term
{m}
Matches exactly m repetitions of the term
{m,}
Matches m or more repetitions of the term
?
The preceding item is optional and matched at most once.
+
The preceding item is matched one or more times.
-
Used between start and end of a range.
\
An escape character to indicate that the following character is a match criteria and
not a grouping delimiter.
>
Redirect output
Table 10: Special Characters
Options
Similar to
Description
[:upper:]
[A-Z]
uppercase letters
[:lower:]
[a-z]
lowercase letters
[:alpha:]
[A-Za-z]
upper- and lowercase letters
\w
[A-Za-z_]
word characters
[:alnum:]
[A-Za-z0-9]
digits, upper- and lowercase letters
[:digit:]
[0-9]
digits
\d
[0-9]
digits
[:xdigit:]
[0-9A-Fa-f]
hexadecimal digits
[:punct:]
[.,!?:...]
punctuation
[:blank:]
[ \t]
space and TAB
[:space:]
[ \t\n\r\f\v]
blank characters
\s
[ \t\n\r\f\v]
blank characters
7210 SAS D, E OS Basic System Configuration Guide
Page 43
Entering CLI Commands
Redirection
The 7210-SAS OS supports redirection (“>”) which allows the operator to store the output of a
CLI command as a local or remote file. Redirection of output can be used to automatically store
results of commands in files (both local and remote).
‘ping <customer_ip> > cf3cf1:/ping/result.txt’
‘ping <customer_ip> > ftp://[email protected]/ping/result.txt’
In some cases only part of the output might be applicable. The pipe/match and redirection
commands can be combined:
ping 10.0.0.1 | match expression “time.\d+” > cf3cf1:/ping/time.txt
This records only the RTT portion (including the word “time”).
Page 44
7210 SAS D, E OS Basic System Configuration Guide
Basic Command Reference
Basic Command Reference
Command Hierarchies
• Global CLI Commands
• Environment Commands
• Monitor Commands
Global CLI Commands
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
back
clear
echo [text-to-echo] [extra-text-to-echo] [more-text]
enable-admin
exec [-echo] [-syntax] filename
exit [all]
help
history
info [detail]
logout
password
ping {ip-address | dns-name} [rapid | detail] [ttl time-to-live] [tos type-of-service] [size bytes] [pattern pattern] [source ip-address] [interval seconds] [{next-hop ip-address} | {interface interfacename} |bypass-routing] [count requests] [do-not-fragment] [router [router-instance][timeout timeout]
pwc [previous]
sleep [seconds]
ssh [ip-addr | dns-name |username@ip-addr] [-l username] [-v SSH-version] [router router-instance]
telnet [ip-address| dns-name] [port] [router router-instance]
traceroute {ip-address | dns-name}[ttl value] [wait milliseconds] [no-dns] [source ip-address] [tos
type-of-service]
tree [detail]
write {user | broadcast} message-string
7210 SAS D, E OS Basic System Configuration Guide
Page 45
Monitor Commands
monitor
— filter
—
—
—
—
— ip ip-filter-id entry entry-id [interval seconds] [repeat repeat] [absolute | rate]
— mac mac-filter-id entry entry-id [interval seconds] [repeat repeat] [absolute | rate]
lag lag-id [lag-id...(up to 5 max)] [interval seconds] [repeat repeat] [absolute | rate]
port port-id [port-id...(up to 5 max)] [interval seconds] [repeat repeat] [absolute | rate]
service
— id service-id
— sap sap-id [interval seconds] [repeat repeat] [absolute | rate]
management-access-filter
— ip entry <entry-id> [interval <seconds>] [repeat <repeat>] [absolute|rate]
Environment Commands
<root>
— environment
— alias <alias-name> <alias-command-name>
— no alias alias-name
— [no] create
— [no] more
— reduced-prompt [no. of nodes in prompt]
— no reduced-prompt
— [no] saved-ind-prompt
— terminal
— length lines
— time-display {local | utc}
— [no] time-stamp
Page 46
7210 SAS D, E OS Basic System Configuration Guide
Root Commands
Basic CLI Commands
Global Commands
enable-admin
Syntax
Context
Description
enable-admin
<global>
NOTE: See the description for the admin-password command. If the admin-password is configured in the config>system>security>password context, then any user can enter a special administrative mode by entering the enable-admin command.
enable-admin is in the default profile. By default, all users are given access to this command.
Once the enable-admin command is entered, the user is prompted for a password. If the password
matches, the user is given unrestricted access to all the commands.
The minimum length of the password is determined by the minimum-length command. The complexity requirements for the password is determined by the complexity command.
The following displays a password configuration example:
A:ALA-1>config>system>security# info
---------------------------------------------...
password
aging 365
minimum-length 8
attempts 5 time 5 lockout 20
admin-password "rUYUz9XMo6I" hash
exit
...
---------------------------------------------A:ALA-1>config>system>security#
There are two ways to verify that a user is in the enable-admin mode:
• show users — Administrator can know which users are in this mode.
• Enter the enable-admin command again at the root prompt and an error message will be
returned.
A:ALA-1# show users
===============================================================================
User Type From Login time Idle time
===============================================================================
admin Console -- 10AUG2006 13:55:24 0d 19:42:22
admin Telnet 10.20.30.93 09AUG2004 08:35:23 0d 00:00:00 A
------------------------------------------------------------------------------Number of users : 2
7210 SAS D, E OS Basic System Configuration Guide
Page 47
Global Commands
'A' indicates user is in admin mode
===============================================================================
A:ALA-1#
A:ALA-1# enable-admin
MINOR: CLI Already in admin mode.
A:ALA-1#
back
Syntax
Context
Description
back
<GLOBAL>
This command moves the context back one level of the command hierarchy. For example, if the current level is the config router ospfconfig router interface interface-id context, the back command
moves the cursor to the config router context level.
clear
Syntax
Context
clear
<GLOBAL>
Description
This command clears statistics for a specified entity or clears and resets the entity.
Parameters
cron — Clears CRON history.
filter — Clears IP, MAC, and log filter counters.
lag — Clears LAG-related entities.
log — Closes and reinitializes the log specified by log-id.
port — Clears port statistics.
qos — Clears QoS statistics.
radius — Clears the RADIUS server state.
router — Clears router commands affecting the router instance in which they are entered.
Values
arp, authentication, bfd, dhcp, forwarding-table, icmp-redirect-route, interface,
isis, ldp, mpls, ospf, rip, rsvp
saa — Clears the SAA test results.
screen — Clears the console or telnet screen.
service — Clears service ID and statistical entities.
system — Clears (re-enables) a previously failed reference.
tacplus — Clears the TACACS+ server state.
trace — Clears the trace log.
Page 48
7210 SAS D, E OS Basic System Configuration Guide
Root Commands
echo
Syntax
Context
echo [text-to-echo] [extra-text-to-echo] [more-text]
<GLOBAL>
Description
This command echoes arguments on the command line. The primary use of this command is to allow
messages to be displayed to the screen in files executed with the exec command.
Parameters
text-to-echo — Specifies a text string to be echoed up to 256 characters.
extra-text-to-echo — Specifies more text to be echoed up to 256 characters.
more-text — Specifies more text to be echoed up to 256 characters.
exec
Syntax
Context
Description
exec [-echo] [-syntax] {filename | <<[eof_string]}
<GLOBAL>
This command executes the contents of a text file as if they were CLI commands entered at the console.
Exec commands do not have no versions.
Parameters
-echo — Echo the contents of the exec file to the session screen as it executes.
Default
Echo disabled.
-syntax — Perform a syntax check of the file without executing the commands. Syntax checking will
be able to find invalid commands and keywords, but it will not be able to validate erroneous usersupplied parameters.
Default
Execute file commands.
filename — The text file with CLI commands to execute.
<< — Stdin can be used as the source of commands for the exec command. When stdin is used as the
exec command input, the command list is terminated with <Ctrl-C>, “EOF<Return>” or
“eof_string<Return>”.
If an error occurs entering an exec file sourced from stdin, all commands after the command
returning the error will be silently ignored. The exec command will indicate the command error
line number when the stdin input is terminated with an end-of-file input.
eof_string — The ASCII printable string used to indicate the end of the exec file when stdin is used as
the exec file source. <Ctrl-C> and “EOF” can always be used to terminate an exec file sourced
from stdin.
Default
Related
Commands
<Ctrl-C>, EOF
boot-bad-exec command on page 226 — Use this command to configure a URL for a CLI script to
exec following a failed configuration boot.
boot-good-exec command on page 226 — Use this command to configure a URL for a CLI script to
exec following a successful configuration boot.
7210 SAS D, E OS Basic System Configuration Guide
Page 49
Global Commands
exit
Syntax
Context
Description
exit [all]
<GLOBAL>
This command returns to the context from which the current level was entered. For example, if you
navigated to the current level on a context by context basis, then the exit command only moves the
cursor back one level.
A:Dut-G# configure
A:Dut-G>config# service
A:Dut-G>config>service# vpls 1
A:Dut-G>config>service>vpls# exit
A:Dut-G>config>service# exit
A:Dut-G>config# exit
If you navigated to the current level by entering a command string, then the exit command returns the
cursor to the context in which the command was initially entered.
A:Dut-G# configure service vpls 1
A:Dut-G>config>service>vpls# exit
A:Dut-G#
The exit all command moves the cursor all the way back to the root level.
A:Dut-G# configure
A:Dut-G>config# service
A:Dut-G>config>service# vpls 1
A:Dut-G>config>service>vpls# exit all
A:Dut-G#
Parameters
all — Exits back to the root CLI context.
help
Syntax
Description
help
help edit
help global
help special-characters
<GLOBAL>
This command provides a brief description of the help system. The following information displays:
Help may be requested at any point by hitting a question mark '?'.
In case of an executable node, the syntax for that node will be displayed with an
explanation of all parameters.
In case of sub-commands, a brief description is provided.
Global Commands:
Help on global commands can be observed by issuing "help globals" at any time.
Editing Commands:
Help on editing commands can be observed by issuing "help edit" at any time.
Parameters
help — Displays a brief description of the help system.
help edit — Displays help on editing.
Available editing keystrokes:
Page 50
7210 SAS D, E OS Basic System Configuration Guide
Root Commands
Delete current character.....................Ctrl-d
Delete text up to cursor.....................Ctrl-u
Delete text after cursor.....................Ctrl-k
Move to beginning of line....................Ctrl-a
Move to end of line..........................Ctrl-e
Get prior command from history...............Ctrl-p
Get next command from history................Ctrl-n
Move cursor left.............................Ctrl-b
Move cursor right............................Ctrl-f
Move back one word...........................Esc-b
Move forward one word........................Esc-f
Convert rest of word to uppercase............Esc-c
Convert rest of word to lowercase............Esc-l
Delete remainder of word.....................Esc-d
Delete word up to cursor.....................Ctrl-w
Transpose current and previous character.....Ctrl-t
Enter command and return to root prompt......Ctrl-z
Refresh input line...........................Ctrl-l
help global — Displays help on global commands.
Available global commands:
back
echo
exec
exit
help
history
info
logout
oam
ping
pwc
sleep
ssh
telnet
traceroute
tree
write
- Go back a level in the command tree
- Echo the text that is typed in
- Execute a file - use -echo to show the commands and
prompts on the screen
- Exit to intermediate mode - use option all to exit to
root prompt
- Display help
- Show command history
- Display configuration for the present node
- Log off this system
+ OAM Test Suite
- Verify the reachability of a remote host
- Show the present working context
- Sleep for specified number of seconds
- SSH to a host
- Telnet to a host
- Determine the route to a destination address
- Display command tree structure from the context of
execution
- Write text to another user
help special-characters — Displays help on special characters.
Use the following CLI commands to display more information about commands and command syntax:
? — Lists all commands in the current context.
string? — Lists all commands available in the current context that start with the string.
command ? — Display command’s syntax and associated keywords.
string<Tab> or string<Space> — Complete a partial command name (auto-completion) or list
available commands that match the string.
7210 SAS D, E OS Basic System Configuration Guide
Page 51
Global Commands
history
Syntax
Context
Description
history
<GLOBAL>
This command lists the last 30 commands entered in this session.
Re-execute a command in the history with the !n command, where n is the line number associated
with the command in the history output.
For example:
A:ALA-1# history
68 info
69 exit
70 info
71 filter
72 exit all
73 configure
74 router
75 info
76 interface "test"
77 exit
78 reduced-prompt
79 info
80 interface "test"
81 icmp unreachables exit all
82 exit all
83 reduced-prompt
84 configure router
85 interface
86 info
87 interface "test"
88 info
89 reduced-prompt
90 exit all
91 configure
92 card 1
93 card-type
94 exit
95 router
96 exit
97 history
A:ALA-1# !91
A:ALA-1# configure
A:ALA-1>config#
info
Syntax
info [detail]
Context
<GLOBAL>
Description
Page 52
This command displays the running configuration for the configuration context.
7210 SAS D, E OS Basic System Configuration Guide
Root Commands
The output of this command is similar to the output of a show config command. This command, however, lists the configuration of the context where it is entered and all branches below that context
level.
By default, the command only enters the configuration parameters that vary from the default values.
The detail keyword causes all configuration parameters to be displayed.
For example,
*A:STU-1>config>service# info detail
---------------------------------------------customer 1 create
description "Default customer"
no contact
no phone
exit
ies 1 customer 1 create
no description
interface "new" create
no description
address 21.0.0.2/8
no mac
arp-timeout 14400
icmp
redirects 100 10
unreachables 100 10
ttl-expired 100 10
exit
sap 1/1/18:0.* create
no description
ingress
no match-qinq-dot1p
no filter
exit
egress
no qinq-mark-top-only
no filter
exit
no shutdown
exit
no shutdown
exit
no shutdown
exit
vpls 100 customer 1 svc-sap-type dot1q create
no description
no disable-learning
no disable-aging
no discard-unknown
fdb-table-size 250
fdb-table-high-wmark 95
fdb-table-low-wmark 90
local-age 300
stp
shutdown
priority 32768
hello-time 2
forward-delay 15
max-age 20
hold-count 6
mode rstp
7210 SAS D, E OS Basic System Configuration Guide
Page 53
Global Commands
exit
mac-move
move-frequency 2
retry-timeout 10
shutdown
exit
sap 1/1/14:100 create
no description
no tod-suite
limit-mac-move blockable
no disable-aging
no max-nbr-mac-addr
no discard-unknown-source
no mac-pinning
stp
path-cost 10
priority 128
no edge-port
auto-edge
link-type pt-pt
no root-guard
no shutdown
exit
dot1ag
exit
no authentication-policy
no l2pt-termination
no bpdu-translation
ingress
qos 1
no match-qinq-dot1p
no filter
exit
egress
no qinq-mark-top-only
no filter
no agg-rate-limit
exit
no collect-stats
no accounting-policy
no shutdown
exit
sap 1/1/15:100 create
no description
no tod-suite
limit-mac-move blockable
no disable-aging
no max-nbr-mac-addr
no discard-unknown-source
no mac-pinning
stp
path-cost 10
priority 128
no edge-port
auto-edge
link-type pt-pt
no root-guard
no shutdown
exit
dot1ag
exit
Page 54
7210 SAS D, E OS Basic System Configuration Guide
Root Commands
no authentication-policy
no l2pt-termination
no bpdu-translation
ingress
qos 1
no match-qinq-dot1p
no filter
exit
egress
no qinq-mark-top-only
no filter
no agg-rate-limit
exit
no collect-stats
no accounting-policy
no shutdown
exit
no shutdown
exit
ies 4001 customer 1 create
no description
interface "inband" create
no description
address 192.168.1.11/24
no mac
arp-timeout 14400
icmp
redirects 100 10
unreachables 100 10
ttl-expired 100 10
exit
sap 1/1/24:0.* create
no description
ingress
no match-qinq-dot1p
no filter
exit
egress
no qinq-mark-top-only
no filter
exit
no shutdown
exit
no shutdown
exit
interface "direct" create
no description
address 10.135.16.97/24
no mac
arp-timeout 14400
icmp
redirects 100 10
unreachables 100 10
ttl-expired 100 10
exit
sap 1/1/21:0.* create
no description
ingress
no match-qinq-dot1p
no filter
exit
7210 SAS D, E OS Basic System Configuration Guide
Page 55
Global Commands
egress
no qinq-mark-top-only
no filter
exit
no shutdown
exit
no shutdown
exit
no shutdown
exit
---------------------------------------------*A:STU-1>config>service#
Parameters
detail — Displays all configuration parameters including parameters at their default values.
logout
Syntax
Context
Description
logout
<GLOBAL>
This command logs out of the router session.
When the logout command is issued from the console, the login prompt is displayed, and any log IDs
directed to the console are discarded. When the console session resumes (regardless of the user), the
log output to the console resumes.
When a Telnet session is terminated from a logout command, all log IDs directed to the session are
removed. When a user logs back in, the log IDs must be re-created.
Page 56
7210 SAS D, E OS Basic System Configuration Guide
Root Commands
password
Syntax
password
Context
<ROOT>
Description
This command changes a user CLI login password.
When a user logs in after the administrator forces a new-password-at-login, or the password has
expired (aging), then this command is automatically invoked.
When invoked, the user is prompted to enter the old password, the new password, and then the new
password again to verify the correct input.
If a user fails to create a new password after the administrator forces a new-password-at-login or
after the password has expired, the user is not allowed access to the CLI.
ping
Syntax
Context
ping {ip-address | dns-name} [rapid | detail] [ttl time-to-live] [tos type-of-service] [size
bytes] [pattern pattern] [source ip-address] [interval seconds] [{next-hop ip-address} |
{interface interface-name} | bypass-routing] [count requests] [do-not-fragment] [router
[router-instance] [timeout timeout]
<GLOBAL>
Description
This command is the TCP/IP utility to verify IP reachability.
Parameters
ip-address | dns-name — The remote host to ping. The IP address or the DNS name (if DNS name
resolution is configured) can be specified.
rapid | detail — The rapid parameter specifies to send ping requests rapidly. The results are reported
in a single message, not in individual messages for each ping request. By default, five ping
requests are sent before the results are reported. To change the number of requests, include the
count option.
The detail parameter includes in the output the interface on which the ping reply was received.
Example output:
*A:ALU-7210# ping 192.xxx.xxx.xxx
PING 192.xxx.xxx.xxx 56 data bytes
64 bytes from 192.xxx.xxx.xxx: icmp_seq=1 ttl=64 time<10ms.
64 bytes from 1192.xxx.xxx.xxx: icmp_seq=2 ttl=64 time<10ms.
64 bytes from 192.xxx.xxx.xxx: icmp_seq=3 ttl=64 time<10ms.
64 bytes from 192.xxx.xxx.xxx: icmp_seq=4 ttl=64 time<10ms.
64 bytes from 192.xxx.xxx.xxx: icmp_seq=5 ttl=64 time<10ms.
---- 192.xxx.xxx.xxx PING Statistics ---5 packets transmitted, 5 packets received, 0.00% packet loss
round-trip min < 10ms, avg < 10ms, max < 10ms, stddev < 10ms
*A:ALU-7210#
7210 SAS D, E OS Basic System Configuration Guide
Page 57
Global Commands
ttl time-to-live — The IP Time To Live (TTL) value to include in the ping request, expressed as a
decimal integer.
Values
0 —128
tos type-of-service — The type-of-service (TOS) bits in the IP header of the ping packets, expressed
as a decimal integer.
Values
0 — 255
size bytes — The size in bytes of the ping request packets.
Default
56 bytes (actually 64 bytes because 8 bytes of ICMP header data are added to the
packet)
Values
0 — 65507
pattern pattern — A 16-bit pattern string to include in the ping packet, expressed as a decimal
integer.
Values
0 — 65535
source ip-address — The source IP address to use in the ping requests in dotted decimal notation.
Default
The IP address of the egress IP interface.
Values
0.0.0.0 — 255.255.255.255
interval seconds — The interval in seconds between consecutive ping requests, expressed as a
decimal integer.
Default
1
Values
1 — 10000
next-hop ip-address — This option disregards the routing table and will send this packet to the
specified next hop address. This address must be on an adjacent router that is attached to a subnet
that is common between this and the next-hop router.
Default
Per the routing table.
Values
A valid IP next hop IP address.
interface interface-name — Specify the interface name.
bypass-routing — Send the ping request to a host on a directly attached network bypassing the
routing table. The host must be on a directly attached network or an error is returned.
count requests — The number of ping requests to send to the remote host, expressed as a decimal
integer.
Default
5
Values
1 — 10000
do-not-fragment — Specifies that the request frame should not be fragmented. This option is
particularly useful in combination with the size parameter for maximum MTU determination.
router router-instance — Specify the router name or service ID.
Page 58
Default
Base
Values
router-name:
service-id:
Base, management
1 — 2147483647
7210 SAS D, E OS Basic System Configuration Guide
Root Commands
timeout timeout — Specify the timeout in seconds.
Default
5
Values
1 — 10
pwc
Syntax
Context
Description
pwc [previous]
<GLOBAL>
This command displays the present or previous working context of the CLI session. The pwc command provides a user who is in the process of dynamically configuring a chassis a way to display the
current or previous working context of the CLI session. The pwc command displays a list of the CLI
nodes that hierarchically define the current context of the CLI instance of the user.
For example,
A:Dut-G>config>service>vpls# pwc
------------------------------------------------------------------------------Present Working Context :
------------------------------------------------------------------------------<root>
configure
service
vpls 1
------------------------------------------------------------------------------A:Dut-G>config>service>vpls#
When the previous keyword is specified, the previous context displays. This is the context entered by
the CLI parser upon execution of the exit command. The current context of the CLI is not affected by
the pwc command.
Parameters
previous — Specifies to display the previous present working context.
sleep
Syntax
Context
sleep [seconds]
<GLOBAL>
Description
This command causes the console session to pause operation (sleep) for 1 second (default) or for the
specified number of seconds.
Parameters
seconds — The number of seconds for the console session to sleep, expressed as a decimal integer.
Default
1
Values
1 — 100
7210 SAS D, E OS Basic System Configuration Guide
Page 59
Global Commands
ssh
Syntax
Context
Description
ssh [ip-addr | dns-name |username@ip-addr] [-l username] [-v SSH-version] [router routerinstance]
<GLOBAL>
This command initiates a client SSH session with the remote host and is independent from the administrative or operational state of the SSH server. However, to be the target of an SSH session, the SSH
server must be operational.
Quitting SSH while in the process of authentication is accomplished by either executing a ctrl-c or
"~." (tilde and dot) assuming the “~” is the default escape character for SSH session.
Parameters
ip-address | host-name — The remote host to which to open an SSH session. The IP address or the
DNS name (providing DNS name resolution is configured) can be specified.
-l user — The user name to use when opening the SSH session.
router router-instance — Specify the router name or service ID.
Values
router-name:
agement.
Default
Base
Base, management (supported only on 7210 SAS-E) ,vpls-man-
telnet
Syntax
Context
telnet [ip-address | dns-name] [port] [router router-instance]
<GLOBAL>
Description
This command opens a Telnet session to a remote host. Telnet servers in networks limit a Telnet clients to three retries to login. The Telnet server disconnects the Telnet client session after three retries.
The number of retry attempts for a Telnet client session is not user-configurable.
Parameters
ip-address — The IP address or the DNS name (providing DNS name resolution is configured) can
be specified.
Values
ipv4-address
a.b.c.d
dns-name — Specify the DNS name (if DNS name resolution is configured).
Values
128 characters maximum
port — The TCP port number to use to Telnet to the remote host, expressed as a decimal integer.
Default
23
Values
1 — 65535
router router-instance — Specify the router name or service ID.
Page 60
Values
router-name:
agement.
Default
Base
Base, management (supported only on 7210 SAS-E) ,vpls-man-
7210 SAS D, E OS Basic System Configuration Guide
Root Commands
traceroute
Syntax
Context
Description
traceroute {ip-address | dns-name} [ttl ttl] [wait milliseconds] [no-dns] [source ip-address]
[tos type-of-service] [router router-instance]
<GLOBAL>
The TCP/IP traceroute utility determines the route to a destination address. Note that aborting a traceroute with the <Ctrl-C> command could require issuing a second <Ctrl-C> command before the
prompt is returned.
A:ALA-1# traceroute 192.168.xx.xx4
traceroute to 192.168.xx.xx4, 30 hops max, 40 byte packets
1 192.168.xx.xx4 0.000 ms 0.000 ms 0.000 ms
A:ALA-1#
Parameters
ip-address | dns-name — The remote address to traceroute. The IP address or the DNS name (if DNS
name resolution is configured) can be specified.
Values
ipv4-address
dns-name
a.b.c.d
128 characters maximum
ttl ttl — The maximum Time-To-Live (TTL) value to include in the traceroute request, expressed as a
decimal integer.
Values
1 — 255
wait milliseconds — The time in milliseconds to wait for a response to a probe, expressed as a
decimal integer.
Default
5000
Values
1 — 60000
no-dns — When the no-dns keyword is specified, a DNS lookup for the specified host name will not
be performed.
Default
DNS lookups are performed
source ip-address — The source IP address to use as the source of the probe packets in dotted
decimal notation. If the IP address is not one of the device’s interfaces, an error is returned.
tos type-of-service — The type-of-service (TOS) bits in the IP header of the probe packets, expressed
as a decimal integer.
Values
0 — 255
router router-instance — Specifies the router name or service ID.
Values
Default
router-name:
agement.
service-id:
Base, management (supported only on 7210 SAS-E) ,vpls-man1 — 2147483647
Base
7210 SAS D, E OS Basic System Configuration Guide
Page 61
Global Commands
tree
Syntax
tree [detail]
Context
<GLOBAL>
Description
This command displays the command hierarchy structure from the present working context.
Parameters
detail — Includes parameter information for each command displayed in the tree output.
write
Syntax
Context
write {user | broadcast} message-string
<GLOBAL>
Description
This command sends a console message to a specific user or to all users with active console sessions.
Parameters
user — The name of a user with an active console session to which to send a console message.
Values
Any valid CLI username
broadcast — Specifies that the message-string is to be sent to all users logged into the router.
message-string — The message string to send. Allowed values are any string up to 250 characters
long composed of printable, 7-bit ASCII characters. If the string contains special characters (#, $,
spaces, etc.), the entire string must be enclosed within double quotes.
Page 62
7210 SAS D, E OS Basic System Configuration Guide
Root Commands
CLI Environment Commands
alias
Syntax
Context
Description
alias alias-name alias-command-line
no alias alias-name
environment
This command enables the substitution of a command line by an alias. Use the alias command to create alternative or easier to remember/understand names for an entity or command string. If the string
contains special characters (#, $, spaces, etc.), the entire string must be enclosed within double
quotes. Only a single command can be present in the command string. The alias command can be
entered in any context but must be created in the root>environment context.
For example, to create an alias named soi to display OSPF interfaces, enter:
alias soi “show router ospf interface”
Parameters
alias-name — The alias name. Do not use a valid command string for the alias. If the alias specified is
an actual command, this causes the command to be replaced by the alias.
alias-command-line — The command line to be associated.
create
Syntax
[no] create
Context
environment
Description
By default, the create command is required to create a new OS entity.
The no form of the command disables requiring the create keyword.
Default
create — The create keyword is required.
Syntax
[no] more
more
Context
Description
environment
This command enables per-screen CLI output, meaning that the output is displayed on a screen-byscreen basis. The terminal screen length can be modified with the terminal command.
The following prompt appears at the end of each screen of paginated output:
Press any key to continue (Q to quit)
The no form of the command displays the output all at once. If the output length is longer than one
screen, the entire output will be displayed, which may scroll the screen.
7210 SAS D, E OS Basic System Configuration Guide
Page 63
CLI Environment Commands
Default
more — CLI output pauses at the end of each screen waiting for the user input to continue.
reduced-prompt
Syntax
Context
Description
reduced-prompt [number of nodes in prompt]
no reduced-prompt
environment
This command configures the maximum number of higher CLI context levels to display in the CLI
prompt for the current CLI session. This command is useful when configuring features that are several node levels deep, causing the CLI prompt to become too long.
By default, the CLI prompt displays the system name and the complete context in the CLI.
The number of nodes specified indicates the number of higher-level contexts that can be displayed in
the prompt. For example, if reduced prompt is set to 2, the two highest contexts from the present
working context are displayed by name with the hidden (reduced) contexts compressed into a ellipsis
(“…”).
A:ALA-1>environment# reduced-prompt 2
A:ALA-1>vonfig>router# interface to-103
A:ALA-1>...router>if#
Note that the setting is not saved in the configuration. It must be reset for each CLI session or stored
in an exec script file.
The no form of the command reverts to the default.
Default
Parameters
no reduced-prompt — Displays all context nodes in the CLI prompt.
number of nodes in prompt — The maximum number of higher-level nodes displayed by name in the
prompt, expressed as a decimal integer.
Default
2
Values
0 — 15
saved-ind-prompt
Syntax
Context
Description
[no] saved-ind-prompt
environment
This command enables saved indicator in the prompt. When changes are made to the configuration
file a “*” appears in the prompt string indicating that the changes have not been saved. When an
admin save command is executed the “*” disappears.
*A:ALA-48# admin save
Writing file to ftp://128.251.10.43/./sim48/sim48-config.cfg
Saving configuration .... Completed.
A:ALA-48#
Page 64
7210 SAS D, E OS Basic System Configuration Guide
Root Commands
terminal
Syntax
terminal
no terminal
Context
environment
Description
This command enables the context to configure the terminal screen length for the current CLI session.
length
Syntax
Context
Default
Parameters
length lines
environment>terminal
24 — Terminal dimensions are set to 24 lines long by 80 characters wide.
lines — The number of lines for the terminal screen length, expressed as a decimal integer.
Values
1 — 512
time-display
Syntax
Context
Description
time-display {local | utc}
environment
This command displays time stamps in the CLI session based on local time or Coordinated Universal
Time (UTC).
The system keeps time internally in UTC and is capable of displaying the time in either UTC or local
time based on the time zone configured.
This configuration command is only valid for times displayed in the current CLI session. This
includes displays of event logs, traps and all other places where a time stamp is displayed.
In general all time stamps are shown in the time selected. This includes log entries destined for console/session, memory, or SNMP logs. Log files on compact flash are maintained and displayed in
UTC format.
Default
time-display local — Displays time stamps based on the local time.
time-stamp
Syntax
time-stamp
Context
environment
Description
This command displays time stamps in the CLI session.
7210 SAS D, E OS Basic System Configuration Guide
Page 65
Monitor CLI Commands
Monitor CLI Commands
filter
Syntax
Context
Description
filter
monitor
This command enables the context to configure criteria to monitor IP and MAC filter statistics.
ip
Syntax
Context
Description
ip ip-filter-id entry entry-id [interval seconds] [repeat repeat] [absolute | rate]
monitor>filter
This command enables IP filter monitoring. The statistical information for the specified IP filter entry
displays at the configured interval until the configured count is reached.
The first screen displays the current statistics related to the specified IP filter. The subsequent
statistical information listed for each interval is displayed as a delta to the previous display.
When the keyword rate is specified, the "rate per second" for each statistic is displayed instead of the
delta.
Monitor commands are similar to show commands but only statistical information displays. Monitor
commands display the selected statistics according to the configured number of times at the interval
specified.
Parameters
ip-filter-id — Displays detailed information for the specified filter ID and its filter entries.
Values
1 — 65535
entry entry-id — Displays information on the specified filter entry ID for the specified filter ID only.
Values
1 — 65535
interval seconds — Configures the interval for each display in seconds.
Default
5 seconds
Values
3 — 60
repeat repeat — Configures how many times the command is repeated.
Default
10
Values
1 — 999
absolute — When the absolute keyword is specified, the raw statistics are displayed, without
processing. No calculations are performed on the delta or rate statistics.
rate — When the rate keyword is specified, the rate-per-second for each statistic is displayed
instead of the delta.
Page 66
7210 SAS D, E OS Basic System Configuration Guide
Root Commands
Sample Output
A:ALA-1>monitor# filter ip 10 entry 1 interval 3 repeat 3 absolute
===============================================================================
Monitor statistics for IP filter 10 entry 1
===============================================================================
At time t = 0 sec (Base Statistics)
------------------------------------------------------------------------------Ing. Matches: 0
Egr. Matches
: 0
------------------------------------------------------------------------------At time t = 3 sec (Mode: Absolute)
------------------------------------------------------------------------------Ing. Matches: 0
Egr. Matches
: 0
------------------------------------------------------------------------------At time t = 6 sec (Mode: Absolute)
------------------------------------------------------------------------------Ing. Matches: 0
Egr. Matches
: 0
------------------------------------------------------------------------------At time t = 9 sec (Mode: Absolute)
------------------------------------------------------------------------------Ing. Matches: 0
Egr. Matches
: 0
===============================================================================
A:ALA-1>monitor#
A:ALA-1>monitor# filter ip 10 entry 1 interval 3 repeat 3 rate
===========================================================================
Monitor statistics for IP filter 10 entry 1
===========================================================================
At time t = 0 sec (Base Statistics)
--------------------------------------------------------------------------Ing. Matches: 0
Egr. Matches
: 0
--------------------------------------------------------------------------At time t = 3 sec (Mode: Rate)
--------------------------------------------------------------------------Ing. Matches: 0
Egr. Matches
: 0
--------------------------------------------------------------------------At time t = 6 sec (Mode: Rate)
--------------------------------------------------------------------------Ing. Matches: 0
Egr. Matches
: 0
--------------------------------------------------------------------------At time t = 9 sec (Mode: Rate)
--------------------------------------------------------------------------Ing. Matches: 0
Egr. Matches
: 0
===========================================================================
A:ALA-1>monitor#
7210 SAS D, E OS Basic System Configuration Guide
Page 67
Monitor CLI Commands
mac
Syntax
Context
Description
mac mac-filter-id entry entry-id [interval seconds] [repeat repeat] [absolute | rate]
monitor>filter
This command enables MAC filter monitoring. The statistical information for the specified MAC
filter entry displays at the configured interval until the configured count is reached.
The first screen displays the current statistics related to the specified MAC filter. The subsequent
statistical information listed for each interval is displayed as a delta to the previous display. When the
keyword rate is specified, the "rate per second" for each statistic is displayed instead of the delta.
Monitor commands are similar to show commands but only statistical information displays. Monitor
commands display the selected statistics according to the configured number of times at the interval
specified.
Parameters
mac-filter-id — The MAC filter policy ID.
Values
1 — 65535
entry entry-id — Displays information on the specified filter entry ID for the specified filter ID only.
Values
1 — 65535
interval seconds — Configures the interval for each display in seconds.
Default
5 seconds
Values
3 — 60
repeat repeat — Configures how many times the command is repeated.
Default
10
Values
1 — 999
absolute — When the absolute keyword is specified, the raw statistics are displayed, without processing. No calculations are performed on the delta or rate statistics.
rate — When the rate keyword is specified, the rate-per-second for each statistic is displayed instead
of the delta.
Sample Output
A:ALA-1>monitor>filter# mac 50 entry 10 interval 3 repeat 3 absolute
===============================================================================
Monitor statistics for Mac filter 50 entry 10
===============================================================================
At time t = 0 sec (Base Statistics)
------------------------------------------------------------------------------Ing. Matches: 0
Egr. Matches
: 0
-----------------------------------------------------------------------------At time t = 3 sec (Mode: Absolute)
------------------------------------------------------------------------------Ing. Matches: 0
Egr. Matches
: 0
-------------------------------------------------------------------------------
Page 68
7210 SAS D, E OS Basic System Configuration Guide
Root Commands
At time t = 6 sec (Mode: Absolute)
------------------------------------------------------------------------------Ing. Matches: 0
Egr. Matches
: 0
------------------------------------------------------------------------------At time t = 9 sec (Mode: Absolute)
------------------------------------------------------------------------------Ing. Matches: 0
Egr. Matches
: 0
===============================================================================
A:ALA-1>monitor>filter# mac 50 entry 10 interval 3 repeat 3 rate
===============================================================================
Monitor statistics for Mac filter 50 entry 10
===============================================================================
At time t = 0 sec (Base Statistics)
------------------------------------------------------------------------------Ing. Matches: 0
Egr. Matches
: 0
------------------------------------------------------------------------------At time t = 3 sec (Mode: Rate)
------------------------------------------------------------------------------Ing. Matches: 0
Egr. Matches
: 0
------------------------------------------------------------------------------At time t = 6 sec (Mode: Rate)
------------------------------------------------------------------------------Ing. Matches: 0
Egr. Matches
: 0
------------------------------------------------------------------------------At time t = 9 sec (Mode: Rate)
------------------------------------------------------------------------------Ing. Matches: 0
Egr. Matches
: 0
===============================================================================
A:ALA-1>monitor>filter#
lag
Syntax
Context
Description
lag lag-id [lag-id...(up to 5 max)] [interval seconds] [repeat repeat] [absolute | rate]
monitor
This command monitors traffic statistics for Link Aggregation Group (LAG) ports. Statistical information for the specified LAG ID(s) displays at the configured interval until the configured count is
reached.
The first screen displays the current statistics related to the specified LAG ID. The subsequent statistical information listed for each interval is displayed as a delta to the previous display. When the keyword rate is specified, the “rate per second” for each statistic is displayed instead of the delta.
Monitor commands are similar to show commands but only statistical information displays. Monitor
commands display the selected statistics according to the configured number of times at the interval
specified.
Parameters
lag-id — The number of the LAG.
Default
none — The LAG ID value must be specified.
Values
1—6
interval seconds — Configures the interval for each display in seconds.
Default
5 seconds
Values
3 — 60
7210 SAS D, E OS Basic System Configuration Guide
Page 69
Monitor CLI Commands
repeat repeat — Configures how many times the command is repeated.
Default
10
Values
1 — 999
absolute — When the absolute keyword is specified, the raw statistics are displayed, without
processing. No calculations are performed on the delta or rate statistics.
rate — When the rate keyword is specified, the rate-per-second for each statistic is displayed instead
of the delta.
Sample Output
A:ALA-12# monitor lag 2
===============================================================================
Monitor statistics for LAG ID 2
===============================================================================
Port-id
Input
Input
Output
Output
Input
Output
Bytes
Packets Bytes
Packets
Errors Errors
------------------------------------------------------------------------------At time t = 0 sec (Base Statistics)
------------------------------------------------------------------------------1/1/1
2168900 26450
64
1
0
0
1/1/2
10677318 125610 2273750
26439
0
0
1/1/3
2168490 26445
0
0
0
0
------------------------------------------------------------------------------Totals
15014708 178505 2273814
26440
0
0
------------------------------------------------------------------------------At time t = 5 sec (Mode: Delta)
------------------------------------------------------------------------------1/1/1
0
0
0
0
0
0
1/1/2
258
3
86
1
0
0
1/1/3
82
1
0
0
0
0
------------------------------------------------------------------------------Totals
340
4
86
1
0
0
===============================================================================
A:ALA-12#
management-access-filter
Syntax
Context
Description
Page 70
management-access-filter
monitor
This command enables the context to monitor management-access filters. These filters are configured
in the config>system>security>mgmt-access-filter context.
7210 SAS D, E OS Basic System Configuration Guide
Root Commands
ip
Syntax
Context
ip entry entry-id [interval seconds] [repeat repeat] [absolute | rate]
monitor>management-access-filter
Description
This command nonitors statistics for the MAF IP filter entry.
Parameters
entry entry-id — Specifies an existing IP MAF entry ID.
Values
1 — 9999
interval seconds — Configures the interval for each display in seconds.
Default
10
Values
3 — 60
repeat repeat — Configures how many times the command is repeated.
Default
10
Values
1 — 999
absolute — When the absolute keyword is specified, the raw statistics are displayed, without
processing. No calculations are performed on the delta or rate statistics.
rate — When the rate keyword is specified, the rate-per-second for each statistic is displayed instead
of the delta.
port
Syntax
Context
Description
port port-id [port-id...(up to 5 max)] [interval seconds] [repeat repeat] [absolute | rate]
monitor
This command enables port traffic monitoring. The specified port(s) statistical information displays
at the configured interval until the configured count is reached.
The first screen displays the current statistics related to the specified port(s). The subsequent
statistical information listed for each interval is displayed as a delta to the previous display. When the
keyword rate is specified, the "rate per second" for each statistic is displayed instead of the delta.
Monitor commands are similar to show commands but only statistical information displays. Monitor
commands display the selected statistics according to the configured number of times at the interval
specified.
Parameters
port port-id — Specify up to 5 port IDs.
interval seconds — Configures the interval for each display in seconds.
Default
5 seconds
Values
3 — 60
repeat repeat — Configures how many times the command is repeated.
7210 SAS D, E OS Basic System Configuration Guide
Page 71
Monitor CLI Commands
Default
10
Values
1 — 999
absolute — When the absolute keyword is specified, the raw statistics are displayed, without
processing. No calculations are performed on the delta or rate statistics.
rate — When the rate keyword is specified, the rate-per-second for each statistic is displayed
instead of the delta.
Sample Output
A:ALA-12>monitor# port 1/1/4 interval 3 repeat 3 absolute
===============================================================================
Monitor statistics for Port 1/1/4
===============================================================================
Input
Output
------------------------------------------------------------------------------At time t = 0 sec (Base Statistics)
------------------------------------------------------------------------------Octets
0
0
Packets
39
175
Errors
0
0
------------------------------------------------------------------------------At time t = 3 sec (Mode: Absolute)
------------------------------------------------------------------------------Octets
0
0
Packets
39
175
Errors
0
0
------------------------------------------------------------------------------At time t = 6 sec (Mode: Absolute)
------------------------------------------------------------------------------Octets
0
0
Packets
39
175
Errors
0
0
------------------------------------------------------------------------------At time t = 9 sec (Mode: Absolute)
------------------------------------------------------------------------------Octets
0
0
Packets
39
175
Errors
0
0
===============================================================================
A:ALA-12>monitor#
A:ALA-12>monitor# port 1/1/4 interval 3 repeat 3 rate
===============================================================================
Monitor statistics for Port 1/1/4
===============================================================================
Input
Output
------------------------------------------------------------------------------At time t = 0 sec (Base Statistics)
------------------------------------------------------------------------------Octets
0
0
Packets
39
175
Errors
0
0
------------------------------------------------------------------------------At time t = 3 sec (Mode: Rate)
------------------------------------------------------------------------------Octets
0
0
Page 72
7210 SAS D, E OS Basic System Configuration Guide
Root Commands
Packets
0
0
Errors
0
0
------------------------------------------------------------------------------At time t = 6 sec (Mode: Rate)
------------------------------------------------------------------------------Octets
0
0
Packets
0
0
Errors
0
0
------------------------------------------------------------------------------At time t = 9 sec (Mode: Rate)
------------------------------------------------------------------------------Octets
0
0
Packets
0
0
Errors
0
0
===============================================================================
A:ALA-12>monitor#
service
Syntax
service
Context
monitor
Description
This command enables the context to configure criteria to monitor specific service SAP criteria.
id
Syntax
Context
Description
id service-id
monitor>service
This command displays statistics for a specific service, specified by the service-id, at the configured
interval until the configured count is reached.
The first screen displays the current statistics related to the service-id. The subsequent statistical
information listed for each interval is displayed as a delta to the previous display. When the keyword
rate is specified, the "rate per second" for each statistic is displayed instead of the delta.
Monitor commands are similar to show commands but only statistical information displays. Monitor
commands display the selected statistics according to the configured number of times at the interval
specified.
Parameters
service-id — The unique service identification number which identifies the service in the service
domain.
sap
Syntax
Context
Description
sap sap-id [interval seconds] [repeat repeat] [absolute | rate]
monitor>service>id service-id
This command monitors statistics for a SAP associated with this service.
7210 SAS D, E OS Basic System Configuration Guide
Page 73
Monitor CLI Commands
This command displays statistics for a specific SAP, identified by the port-id and encapsulation value,
at the configured interval until the configured count is reached.
The first screen displays the current statistics related to the SAP. The subsequent statistical information listed for each interval is displayed as a delta to the previous display. When the keyword rate is
specified, the “rate per second” for each statistic is displayed instead of the delta.
Monitor commands are similar to show commands but only statistical information displays. Monitor
commands display the selected statistics according to the configured number of times at the interval
specified.
Parameters
sap-id — Specifies the physical port identifier portion of the SAP definition.
Values sap-id:
null
dot1q
qinq
port-id
lag-id
qtag1
qtag2
[port-id | lag-id]
[port-id | lag-id]:* | qtag
[port-id | lag-id]:qtag1.qtag2
slot/mda/port
lag-id
lag
keyword
id
1 — 200
0 — 4094
*, 0 — 4094
port-id — Specifies the physical port ID in the slot/mda/port format.
If the card in the slot has Media Dependent Adapters (MDAs) installed, the port-id must be in the
slot_number/MDA_number/port_number format. For example 1/2/3 specifies port 3 on MDA 2
in slot 1.
qtag1, qtag2 — Specifies the encapsulation value used to identify the SAP on the port or sub-port. If
this parameter is not specificially defined, the default value is 0.
Values
qtag1:
qtag2 :
0 — 4094
* | 0 — 4094
The values depends on the encapsulation type configured for the interface. The following table
describes the allowed values for the port and encapsulation types.
Port Type
Encap-Type
Allowed Values
Comments
Ethernet
Null
0
The SAP is identified by the port.
Ethernet
Dot1q
0 — 4094
The SAP is identified by the 802.1Q tag on the port.
Note that a 0 qtag1 value also accepts untagged packets
on the dot1q port.
Ethernet
QinQ
qtag1: 0 — 4094
qtag2: 0 — 4094
The SAP is identified by two 802.1Q tags on the port.
Note that a 0 qtag1 value also accepts untagged packets
on the dot1q port.
interval seconds — Configures the interval for each display in seconds.
Page 74
Default
11 seconds
Values
11 — 60
7210 SAS D, E OS Basic System Configuration Guide
Root Commands
repeat repeat — Configures how many times the command is repeated.
Default
10
Values
1 — 999
absolute — When the absolute keyword is specified, the absolute rate-per-second value for each
statistic is displayed.
rate — When the rate keyword is specified, the rate-per-second for each statistic is displayed instead
of the delta.
Sample Output
A:7210SAS-E>monitor>service>id# sap 1/1/1:100
===============================================================================
Monitor statistics for Service 10000 SAP 1/1/1:100
===============================================================================
------------------------------------------------------------------------------At time t = 110 sec (Mode: Delta)
------------------------------------------------------------------------------------------------------------------------------------------------------------Ingress QoS Classifier Usage
------------------------------------------------------------------------------Classifiers Allocated: 16 Meters Allocated : 8
Classifiers Used : 2 Meters Used : 2
------------------------------------------------------------------------------Sap Statistics
------------------------------------------------------------------------------Packets Octets
Ingress Stats: 1013264 0
Egress Stats: 163674 0
------------------------------------------------------------------------------Sap STP Statistics
------------------------------------------------------------------------------Forward transitions : 0 Bad BPDUs rcvd : 0
Cfg BPDUs rcvd : 0 Cfg BPDUs tx : 0
TCN BPDUs rcvd : 0 TCN BPDUs tx : 0
RST BPDUs rcvd : 0 RST BPDUs tx : 0
MST BPDUs rcvd : 0 MST BPDUs tx : 0
------------------------------------------------------------------------------Sap per Meter Stats
------------------------------------------------------------------------------Packets Octets
Ingress Meter 1 (Unicast)
For. InProf : 0
0
For. OutProf : 210645 0
Ingress Meter 11 (Multipoint)
For. InProf : 0
0
For. OutProf : 87238 0
===============================================================================
A:7210SAS-E>monitor>service>id#
7210 SAS D, E OS Basic System Configuration Guide
Page 75
Show Commands
Show Commands
alias
Syntax
Context
Description
Output
alias
<root>
This command displays a list of existing aliases.
Show Alias Fields — The following table describes alias output fields.
Table 11: Show Alias Output Fields
Label
Description
Alias-Name
Displays the name of the alias.
Alias-command-name
The command and parameter syntax that define the alias.
Number of aliases
The total number of aliases configured on the router.
Sample Output
A:ALA-103>config>system# show alias
==============================================================================
Alias-Name
Alias-command-name
==============================================================================
sri
show router interface
sse
show service service-using epipe
ssvpls
show service service-using vpls
ssi
show service service-using ies
-----------------------------------------------------------------------------Number of aliases : 5
==============================================================================
A:ALA-103>config>system#
Page 76
7210 SAS D, E OS Basic System Configuration Guide
File System Management
In This Chapter
This chapter provides information about file system management.
Topics in this chapter include:
•
The File System on page 78
→ Compact Flash Devices on page 78
→ URLs on page 79
→ Wildcards on page 80
•
File Management Tasks on page 81
→ Modifying File Attributes on page 81
→ Creating Directories on page 82
→ Copying Files on page 83
→ Moving Files on page 84
→ Removing Files and Deleting Directories on page 84
→ Displaying Directory and File Information on page 85
7210 SAS D, E OS Basic System Configuration Guide
Page 77
The File System
The File System
The 7210 SAS file system is used to store files used and generated by the system, for example,
image files, configuration files, logging files and accounting files.
The file commands allow you to copy, create, move, and delete files and directories, navigate to a
different directory, display file or directory contents and the image version.
Compact Flash Devices
The file system is based on a DOS file system. In 7210 SAS, the node has a single compact flash
(internal). The name of this compact flash device is “cf1:”,
The above device names are relative device names as they refer to the devices local to the control
processor with the current console session. As in the DOS file system, the colon (“:”) at the end of
the name indicates it is a device.
The compact flash devices on the 7210 SAS devices are non-removable.
Page 78
7210 SAS D, E OS Basic System Configuration Guide
File System Management
URLs
The arguments for the 7210 SAS OS file commands are modeled after standard universal resource
locator (URL). A URL refers to a file (a file-url) or a directory (a directory-url).
7210 SAS OS supports operations on both the local file system and on remote files. For the
purposes of categorizing the applicability of commands to local and remote file operations, URLs
are divided into three types of URLs: local, ftp and tftp. The syntax for each of the URL types are
listed in Table 12.
Table 12: URL Types and Syntax
URL Type
Syntax
Notes
local-url
[cflash-id:\]path
cflash-id is the compact flash device name.
Values: cf1:
ftp-url
ftp://[username[:password]@]host/path
An absolute ftp path from the root of the remote
file system.
username is the ftp user name
password is the ftp user password
host is the remote host
path is the path to the directory or file
ftp://[username[:password]@]host/./path
A relative ftp path from the user’s home
directory. Note the period and slash (“./”) in this
syntax compared to the absolute path.
tftp://host[/path]/filename
tftp is only supported for operations on file-urls.
tftp-url
The system accepts either forward slash (“/”) or backslash (“\”) characters to delimit directory
and/or filenames in URLs. Similarly, the 7210 SAS OS SCP client application can use either slash
or backslash characters, but not all SCP clients treat backslash characters as equivalent to slash
characters. In particular, UNIX systems will often times interpret the backslash character as an
“escape” character. This can cause problems when using an external SCP client application to
send files to the SCP server. If the external system treats the backslash like an escape character, the
backslash delimiter will get stripped by the parser and will not be transmitted to the SCP server.
For example, a destination directory specified as “cf1:\dir1\file1” will be transmitted to the SCP
server as “cf1:dir1file1” where the backslash escape characters are stripped by the SCP client
system before transmission. On systems where the client treats the backslash like an “escape”
character, a double backslash “\\” or the forward slash “/” can typically be used to properly delimit
directories and the filename.
7210 SAS D, E OS Basic System Configuration Guide
Page 79
The File System
Wildcards
7210 SAS OS supports the standard DOS wildcard characters. The asterisk (*) can represent zero
or more characters in a string of characters, and the question mark (?) can represent any one
character.
Example: A:ALA-1>file cf1:\ # copy test*.cfg siliconvalley
cf1:\testfile.cfg
1 file(s) copied.
A:ALA-1>file cf1:\ # cd siliconvalley
A:ALA-1>file cf1:\siliconvalley\ # dir
Volume in drive cf1 on slot A has no label.
Directory of cf1:\siliconvalley\
05/10/2006 11:32p
<DIR>
.
05/10/2006 11:14p
<DIR>
..
05/10/2006 11:32p
7597 testfile.cfg
1 File(s)
7597 bytes.
2 Dir(s)
1082368 bytes free.
A:ALA-1>file cf1:\siliconvalley\ #
All the commands can operate on the local file system. Table 13 indicates which commands also
support remote file operations.
Table 13: File Command Local and Remote File System Support
Command
local-url
attrib
X
cd
X
X
copy
X
X
delete
X
X
dir
X
X
move
X
X
X
X
rd
scp
tftp-url
X
md
Page 80
ftp-url
source only
type
X
X
X
version
X
X
X
7210 SAS D, E OS Basic System Configuration Guide
File System Management
File Management Tasks
The following sections are basic system tasks that can be performed.
Note that when a file system operation is performed with the copy, delete, move, rd, or scp
commands that can potentially delete or overwrite a file system entry, a prompt appears to confirm
the action. The force keyword performs the copy, delete, move, rd, and scp actions without
displaying the confirmation prompt.
•
Modifying File Attributes on page 81
•
Creating Directories on page 82
•
Copying Files on page 83
•
Moving Files on page 84
•
Removing Files and Deleting Directories on page 84
•
Displaying Directory and File Information on page 85
Modifying File Attributes
The system administrator can change the read-only attribute in the local file. Enter the attrib
command with no options to display the contents of the directory and the file attributes.
Use the CLI syntax displayed below to modify file attributes:
CLI Syntax: file>
attrib [+r | -r] file-url
The following displays an example of the command syntax:
Example: # file
file cf1:\ # attrib
file cf1:\ # attrib +r BOF.SAV
file cf1:\ # attrib
7210 SAS D, E OS Basic System Configuration Guide
Page 81
File Management Tasks
The following displays the file configuration:
A:ALA-1>file cf1:\ # attrib
cf1:\bootlog.txt
cf1:\bof.cfg
cf1:\boot.ldr
cf1:\bootlog_prev.txt
cf1:\BOF.SAV
A:ALA-1>file cf1:\ # attrib +r BOF.SAV
A:ALA-1>file cf1:\ # attrib
cf1:\bootlog.txt
cf1:\bof.cfg
cf1:\boot.ldr
cf1:\bootlog_prev.txt
R
cf1:\BOF.SAV
Creating Directories
Use the md command to create a new directory in the local file system, one level at a time.
Enter the cd command to navigate to different directories.
Use the CLI syntax displayed below to modify file attributes:
CLI Syntax: file>
md file-url
The following displays an example of the command syntax:
Example: file cf1:\ # md test1
file
file
file
file
file
file
Page 82
cf1:\ # cd test1
cf1:\test1\ # md test2
cf1:\test1\ # cd test2
cf1:\test1\test2\ # md test3
cf1:\test1\test2\ # cd test3
cf1:\test1\test2\test3 #
7210 SAS D, E OS Basic System Configuration Guide
File System Management
Copying Files
Use the copy command to upload or download an image file, configuration file, or other file types
to or from a flash card or a TFTP server.
The scp command copies files between hosts on a network. It uses SSH for data transfer, and uses
the same authentication and provides the same security as SSH.
The source file for the scp command must be local. The file must reside on the router. The
destination file has to be of the format: user@host:file-name. The destination does not need to be
local.
Use the CLI syntax displayed below to copy files:
CLI Syntax: file>
copy source-file-url dest-file-url [force]
scp local-file-url destination-file-url [router router name | service-id] [force]
The following displays an example of the copy command syntax:
Example: A:ALA-1>file cf1:\ # copy 104.cfg cf1:\test1\test2\test3\test.cfg
A:ALA-1>file cf1:\ # scp file1 [email protected]:cf1:\file1
A:ALA-1>file cf1:\ # scp file2 [email protected]:/user2/file2
A:ALA-1>file cf1:\ # scp cf1:/file3 [email protected]:cf1:\file3
7210 SAS D, E OS Basic System Configuration Guide
Page 83
File Management Tasks
Moving Files
Use the move command to move a file or directory from one location to another.
Use the CLI syntax displayed below to move files:
CLI Syntax: file>
move old-file-url new-file-url [force]
The following displays an example of the command syntax:
Example: A:ALA-1>file cf1:\test1\test2\test3\ # move test.cfg cf1:\test1
cf1:\test1\test2\test3\test.cfg
A:ALA-1>file cf1:\test1\test2\test3\ # cd ..
A:ALA-1>file cf1:\test1\test2\ # cd ..
A:ALA-1>file cf1:\test1\ # dir
Directory of cf1:\test1\
05/04/2006 07:58a
<DIR>
.
05/04/2006 07:06a
<DIR>
..
05/04/2006 07:06a
<DIR>
test2
05/04/2006 07:58a
25278 test.cfg
1 File(s)
25278 bytes.
3 Dir(s)
1056256 bytes free.
A:ALA-1>file cf1:\test1\ #
Removing Files and Deleting Directories
Use the delete and rd commands to delete files and remove directories. Directories must be
empty in order to delete them. When file or directories are deleted they cannot be recovered.
Use the CLI syntax displayed below to delete files and remove directories:
CLI Syntax: file>
delete file-url [force]
rd file-url [force]
The following displays an example of the command syntax:
A:ALA-1>file
A:ALA-1>file
A:ALA-1>file
A:ALA-1>file
A:ALA-1>file
A:ALA-1>file
A:ALA-1>file
A:ALA-1>file
A:ALA-1>file
A:ALA-1>file
Page 84
cf1:\test1\ # delete test.cfg
cf1:\test1\ # delete abc.cfg
cf1:\test1\test2\ # cd test3
cf1:\test1\test2\test3\ # cd ..
cf1:\test1\test2\ # rd test3
cf1:\test1\test2\ # cd ..
cf1:\test1\ # rd test2
cf1:\test1\ # cd ..
cf1:\ # rd test1
cf1:\ #
7210 SAS D, E OS Basic System Configuration Guide
File System Management
Displaying Directory and File Information
Use the dir command to display a list of files on a file system.
The type command displays the contents of a file.
The version command displays the version of a cpm.tim or iom.timfile.
Use the CLI syntax displayed below to display directory and file information:
CLI Syntax: file>
dir [file-url]
type file-url
version file-url
The following displays an example of the command syntax:
*A:card-1>file cf1:\ # dir
Volume in drive cf1 on slot A is /flash.
Volume in drive cf1 on slot A is formatted as FAT32.
Directory of cf1:\
10/22/2008
10/22/2008
10/22/2008
02/01/2001
02/01/2001
10/22/2008
10/17/2008
10/15/2008
10:30a
10:30a
10:29a
09:25a
09:21a
11:07a
<DIR>
07:32p
03:38p
7 File(s)
1 Dir(s)
8849
733
5531
3528373
4860
bootlog.txt
bof.cfg
bootlog_prev.txt
boot.tim
config.cfg
test1
724 env.cfg
9499 snake.cfg
3558569 bytes.
53135360 bytes free.
7210 SAS D, E OS Basic System Configuration Guide
Page 85
File Management Tasks
Page 86
7210 SAS D, E OS Basic System Configuration Guide
File Commands
File Command Reference
Command Hierarchy
Configuration Commands
file
—
—
—
—
—
—
—
—
—
—
—
—
—
attrib [+r | -r] file-url
attrib
cd [file-url]
copy source-file-url dest-file-url [force]
delete file-url [force]
dir [file-url]
format cflash cflash-id [reliable]
md file-url
move old-file-url new-file-url [force]
rd file-url [force]
scp local-file-url destination-file-url [router router-instance] [force]
type file-url
version file-url [check]
7210 SAS D, E OS Basic System Configuration Guide
Page 87
File Command Reference
Page 88
7210 SAS D, E OS Basic System Configuration Guide
Configuration Commands
Configuration Commands
File Commands
attrib
Syntax
Context
Description
attrib [+r | -r] file-url
attrib
file
This command sets or clears/resets the read-only attribute for a file in the local file system. To list all
files and their current attributes enter attrib or attrib x where x is either the filename or a wildcard
(*).
When an attrib command is entered to list a specific file or all files in a directory, the file’s attributes
are displayed with or without an “R” preceding the filename. The “R” implies that the +r is set and
that the file is read-only. Files without the “R” designation implies that the -r is set and that the file is
read-write-all. For example:
ALA-1>file cf1:\ # attrib
cf1:\bootlog.txt
cf1:\bof.cfg
cf1:\boot.ldr
cf1:\sr1.cfg
cf1:\test
cf1:\bootlog_prev.txt
R cf1:\BOF.SAV
Parameters
file-url — The URL for the local file.
Values
local-url | remote-url:
local-url:
remote-url
cf1:,cf1-A:
255 chars max
[cflash-id/][file-path]
[ftp://login:pswd@remote-locn/][file-path]
+r — Sets the read-only attribute on the specified file.
-r — Clears/resets the read-only attribute on the specified file.
cd
Syntax
Context
Description
cd [file-url]
file
This command displays or changes the current working directory in the local file system.
7210 SAS D, E OS Basic System Configuration Guide
Page 89
File Commands
Parameters
file-url — Syntax:
[local-url | remote-url (255 chars max)
local-url - [cflash-id/][file-path]
remote-url - [{ftp://|tftp://}login:pswd@remote-locn/][file-path]
cf1:
<none> — Displays the current working directory.
.. — Signifies the parent directory. This can be used in place of an actual directory name in a
directory-url.
directory-url — The destination directory.
copy
Syntax
Context
Description
copy source-file-url dest-file-url [force]
file
This command copies a file or all files in a directory from a source URL to a destination URL. At
least one of the specified URLs should be a local URL. The optional wildcard (*) can be used to copy
multiple files that share a common (partial) prefix and/or (partial) suffix.
When a file is copied to a destination with the same file name, the original file is overwritten by the
new file specified in the operation. The following prompt appears if the destination file already exists:
“Overwrite destination file (y/n)?”
For example:
To copy a file named srcfile in a directory called test on cf1 to a file called
destfile in a directory called production on cf1, the syntax is:
sr1>file cf1:\ # copy cf2-/test/srcfile/production/destfile
To FTP a file named 121201.cfg in directory mydir stored on cf1 to a network FTP
server with IP address 131.12.31.79 in a directory called backup with a destination file name of 121201.cfg, the FTP syntax is:
copy /mydir/121201.cfg 131.12.31.79/backup/121201.cfg
Parameters
source-file-url — The location of the source file or directory to be copied.
dest-file-url — The destination of the copied file or directory.
force — Forces an immediate copy of the specified file(s).
file copy force executes the command without displaying a user prompt message.
delete
Syntax
Context
Description
Page 90
delete file-url [force]
file
This command deletes the specified file.
7210 SAS D, E OS Basic System Configuration Guide
Configuration Commands
The optional wildcard “*” can be used to delete multiple files that share a common (partial) prefix
and/or (partial) suffix. When the wildcard is entered, the following prompt displays for each file that
matches the wildcard:
“Delete file <filename> (y/n)?”
file-url — The file name to delete.
Values
local-url | remote-url:
local-url:
remote-url
cf1:
255 chars max
[cflash-id/][file-path]
[ftp://login:pswd@remote-locn/][file-path]
force — Forces an immediate deletion of the specified file(s).
file delete * force deletes all the wildcard matching files without displaying a user prompt message.
dir
Syntax
Context
dir [file-url]
file
Description
This command displays a list of files and subdirectories in a directory.
Parameters
file-url — The path or directory name.
Use the file-url with the optional wildcard (*) to reduce the number of files to list.
Default
Lists all files in the present working directory
file
Syntax
file
Context
root
Description
The context to enter and perform file system operations. When entering the file context, the prompt
changes to reflect the present working directory. Navigating the file system with the cd .. command
results in a changed prompt.
The exit all command leaves the file system/file operation context and returns to the <ROOT> CLI
context. The state of the present working directory is maintained for the CLI session. Entering the file
command returns the cursor to the working directory where the exit command was issued.
7210 SAS D, E OS Basic System Configuration Guide
Page 91
File Commands
format
Syntax
Context
format cflash cflash-id
root>file
Description
This command formats the compact flash. The compact flash must be shutdown before starting the
format.
Parameters
cflash-id — The compact flash type.
Values
cf1:
md
Syntax
Context
Description
md file-url
file
This command creates a new directory in a file system.
Directories can only be created one level at a time.
Parameters
file-url — The directory name to be created.
Values
local-url | remote-url:
local-url:
remote-url
cf1:
255 chars max
[cflash-id/][file-path]
[ftp://login:pswd@remote-locn/][file-path]
move
Syntax
Context
Description
move old-file-url new-file-url [force]
file
This command moves a local file, system file, or a directory. If the target already exists, the command
fails and an error message displays.
The following prompt appears if the destination file already exists:
“Overwrite destination file (y/n)?”
Parameters
old-file-url — The file or directory to be moved.
Values
Page 92
local-url | remote-url:
local-url:
remote-url
cf1:
255 chars max
[cflash-id/][file-path]
[ftp://login:pswd@remote-locn/][file-path]
7210 SAS D, E OS Basic System Configuration Guide
Configuration Commands
new-file-url — The new destination to place the old-file-url.
Values
local-url | remote-url:
local-url:
remote-url
cf1:
255 chars max
[cflash-id/][file-path]
[ftp://login:pswd@remote-locn/][file-path]
force — Forces an immediate move of the specified file(s).
file move force executes the command without displaying a user prompt message.
rd
Syntax
Context
Description
rd file-url [force]
file
The rd command is used to delete a directory.
If a directory has files and no sub-directories, the force option must be used to force delete the directory and files it contains.
Parameters
file-url — The directory to be removed.
Values
local-url | remote-url:
local-url:
remote-url
cf1:
255 chars max
[cflash-id/][file-path]
[ftp://login:pswd@remote-locn/][file-path]
force — Forces an immediate deletion of the specified directory.
For example, rd file-url force executes the command without displaying a user prompt message.
scp
Syntax
Context
Description
scp local-file-url destination-file-url [router router-instance] [force]
file
This command copies a local file to a remote host file system. It uses ssh for data transfer, and uses
the same authentication and provides the same security as ssh. The following prompt appears:
“Are you sure (y/n)?” The destination must specify a user and a host.
Parameters
local-file-url — The local source file or directory.
Values
[cflash-id/][file-path]: Up to 256 characters.
destination-file-url — The destination file.
Values
user@hostname:destination-file
user — The SSH user.
host — The remote host IP address of DNS name.
7210 SAS D, E OS Basic System Configuration Guide
Page 93
File Commands
file-path — The destination path.
router-instance — Specify the router name or service ID.
Values
router-name:
service-id:
Default
Base
Base , management
1 — 2147483647
force — Forces an immediate copy of the specified file.
file scp local-file-url destination-file-url [router] force executes the command without displaying a user prompt message.
type
Syntax
Context
Description
type file-url
file
Displays the contents of a text file.
version
Syntax
Context
version file-url [check]
file
Description
This command displays the version of a TiMOS file.
Parameters
file-url — The file name of the target file.
Values
local-url | remote-url:
local-url:
remote-url:
cflash-id:
255 characters maximum
[cflash-id/][file-path]
[{ftp://|tftp://}login:pswd@remote-locn/][file-path]
cf1:,
check — Validates the .tim file.
Page 94
7210 SAS D, E OS Basic System Configuration Guide
Boot Options
In This Chapter
This chapter provides information about configuring boot option parameters.
Topics in this chapter include:
•
System Intialization on page 96
→ Manual Mode on page 99
→ Auto Init on page 100
→ Ping Check on page 105
−
Persistence on page 106
•
Initial System Startup Process Flow on page 108
•
Configuration Notes on page 109
7210 SAS D, E OS Basic System Configuration Guide
Page 95
System Intialization
System Intialization
When the system is powered ON it executes the bootstrap image, for example, the boot.tim file,
from the file system which is located on a non-removable flash device (cf1:) that is built in to the
7210 SAS-Series router. The boot.tim file is the image that reads and executes the system
initialization commands configured in the Boot Option File (BOF). The default behavior is to
initially search for the boot.tim file on cf1:. This behavior cannot be modified. If the boot.tim file
is not present, or is not a valid loadable file, the Golden bootstrap image is loaded by the bootrom.
This image is equivalent to a boot.tim file except that it is present outside the file system and can
be updated and checked by means of special CLI commands.
When the system executes boot.tim, provision is given to the user to modify the BOF
manually and save it or to boot using existing BOF. The bootstrap image then processes the BOF
file present in the flash as explained in Configuration and Image Loading on page 102. The system
is shipped to the customer site with a boot.tim file and a Golden bootstrap image, but without a
BOF file. When the system is powered ON for the first time, there will be no BOF in the system.
Hence, provisions are given to create a new BOF file or alternatively get the BOF file from the
network. There are two options:
•
Boot by manually creating a BOF file (manual boot).
•
Boot by retrieving the BOF file from the network, using DHCP to get the network location
of the BOF file (auto init). Auto-init is the default boot procedure if there is no manualintervention during the first boot.
Note: When the operator executes the reset command in the boot loader prompt or admin
reboot auto-init in the TiMos CLI, 7210 SAS resets the current BOF and reboots.
Note: The operator can manage a 7210 SAS E node through an external physical network.
Managing a node through an external physical network secures the management network
by restricting access to service customers and service data. The 7210 SAS E node can be
managed through the Out-of-band (OOB) Ethernet management port. The 7210 SAS-D
devices do not support Out-of-band Ethernet management port.
The following is an example of console display output when the boot.tim file is located on cf1 and
the system boots successfully.
Alcatel-Lucent 7210 Boot ROM. Copyright 2000-2009 Alcatel-Lucent.
All rights reserved. All use is subject to applicable license agreements.
Running POST tests from ROM
Testing ROM load area...done
Relocating code...Jumping to RAM
Performing second stage RAM test....passed
Board Serial Number is 'SN123456789'
Bootlog started for Version V-0.0.I317
Build V-0.0.I317 bootrom/mpc 7xxx
Built on Tue Jan 6 02:23:14 IST 2009 by panosbld in /panosbld/ws/panos/main
Page 96
7210 SAS D, E OS Basic System Configuration Guide
Boot Option Files
?Attempting to load from file cf1:/boot.tim
Version L-0.0.I312, Fri Jan 2 04:26:32 IST 2009 by panosbld in /panosbld/ws/panos/main
text:(3002475-->12623392) + data:(550940-->2414128)
Starting at 0xb000000...
Total Memory: 512MB Chassis Type: sas
TiMOS-L-0.0.I312 boot/mpc ALCATEL SAS-E
All rights reserved. All use subject to
Built on Fri Jan 2 04:26:32 IST 2009 by
Card Type: badami_7210
7210 Copyright (c) 2000-2009 Alcatel-Lucent.
applicable license agreements.
panosbld in /panosbld/ws/panos/main
TiMOS BOOT LOADER
...
Figure 3 displays the bootstrap load process.
Power on/Reboot – Start Bootrom
code
Yes
Was Golden image requested
due to bootstrap image
upgrade failure?
Load golden
bootstrap
image
No
No
boot.tim present
and valid
R
Yes
boot.tim a different version from last
good bootstrap image
No
Yes
Indicate bootstrap-updated flag
to timos and the bootstrap
image
Load
boot.tim
Indicate bootstrap-no-update
flag to timos and the bootstrap
image
R
Figure 3: Bootstrap Load Process - System Initialisation - Part I
Figure 4 displays the flash directory structure and file names.
7210 SAS D, E OS Basic System Configuration Guide
Page 97
System Intialization
Figure 4: Files on the Flash
Files on the compact flash are:
•
bof.cfg — Boot option file
•
boot.tim — Bootstrap image
•
config.cfg — Default configuration file
•
TIMOS-m.n.Yz:
m — Major release number
n — Minor release number
Y: A — Alpha release
B — Beta release
M — Maintenance release
R — Released software
z — Version number
both.tim — CPM and IOM image file
Page 98
7210 SAS D, E OS Basic System Configuration Guide
Boot Option Files
Manual Mode
Note: Out-of-Band Ethernet management port is not supported on 7210 SAS-D devices.
If the user opts for the manual-mode boot procedure for the first time boot, the required
parameters must be specified for a successful system boot. Manual mode configurations require
authentication. The default password is password. BOF parameters that should be configured
include:
•
Image path
•
Configuration file path
•
UplinkA parameters (port number, vlan ID, IP/mask, static route)
•
UplinkB parameters (port number, vlan ID, IP/mask, static route)
•
eth-mgmt-disable (supported only on 7210 SAS-E)
Provisions to configure two uplinks is given in the BOF for port redundancy. If the image path and
configuration file path are local, then the IP address and routing information for uplinkA and
uplinkB are not required. The user can optionally obtain IP parameters through DHCP by
configuring 0 (zero) for the uplink port’s IP address. In this case, the DHCP server should be
configured to grant the IP address and the default gateway information used to reach the server
where the image and configuration files are present. After the BOF configuration is completed, a
BOF with configured parameters is created in the flash that can be used for subsequent reboots.
The bootstrap image then processes the BOF parameters in order to boot the system. BOF
processing is explained in Configuration and Image Loading on page 102.
For 7210 SAS-E devices, eth-mgmt-disable parameter indicates if the out-of-band Ethernet
management port is enabled during the boot-up procedure. The 7210 SAS-D devices do not
support Out-of-band Ethernet management port. For a 7210 node which has a previous BOF, the
boot process uses the existing parameters for uplink A and uplink B ports to boot the TIMOS
image. The OOB port is disabled, by default.
7210 SAS D, E OS Basic System Configuration Guide
Page 99
System Intialization
Auto Init
During the first boot or a reboot after the execution of CLI command admin reboot auto-init, if
the user does not intervene to create the BOF file in the manual mode, the system, by default, goes
to auto-init procedure after a “wait” time. The default wait time is 3 seconds. There are two
designated ports used for auto init. These are the front panel ports, port 1 and port 2. Auto init
requires a DHCP server to be configured in the network which should be reachable by the system.
DHCP requests are directed out of one uplink port at a time. All other ports of the system would be
down.
If a DHCP server is present in the network, the system expects to receive an IP address, the default
gateway information, and BOF file path in the response returned by the DHCP server. Upon
receiving these parameters from DHCP server, the system will apply the IP configuration and then
download the BOF file from the path given by the DHCP server. The BOF file is then saved into
the flash and is used for subsequent reboots. The bootstrap image then processes the BOF
parameters in order to boot the system. BOF processing is explained in Configuration and Image
Loading on page 102
The system first attempts to use uplinkA and then uplinkB parameters to receive a successful
response from the DHCP server. If there is no response from the DHCP server on both the uplink
ports, the boot procedure is restarted, during which the user can opt to enter the manual mode or
allow the system to default to auto-init again.
Note: Ethernet management port does not support AutoInit mode. The use of DHCP to obtain the
BOF file from the network and other system parameters is currently not supported on Ethernet
management port.
Page 100
7210 SAS D, E OS Basic System Configuration Guide
Boot Option Files
Out-of-band (OOB) Ethernet Management Port
Note: Out-of-band Ethernet port is not supported on 7210 SAS-D devices.
An Out-of-band Ethernet port can be used to download the TIMOS image file and the
configuration file. In the Autoinit manual mode, if the OOB port is enabled (that is the eth-mgmtdisable is set to “no”), the OOB port is used to download the TIMOS image file and configuration
file specified in the BOF file, and the system boot is successfully completed. If a system boot fails,
the uplink A and uplink B parameters are used to retrieve the TIMOS image and configuration
files.
7210 SAS D, E OS Basic System Configuration Guide
Page 101
Configuration and Image Loading
Configuration and Image Loading
The bootstrap image processes the initialization parameters from the BOF. The bootstrap image
attempts to locate the configuration file as configured in the BOF. Up to three locations can be
configured for the system to search for the configuration file. The locations can be local or remote.
The first location searched is the primary configuration location. If not found, the secondary
configuration location is searched, and lastly, the tertiary configuration location is searched. If the
configuration file is in a remote location, the bootstrap process saves it on the flash as cf1:/
default.cfg. Users must not delete this file or create a file with this name. The configuration file
includes chassis, MDA, and port configurations, as well as system, routing, and service
configurations. Like the configuration file, three locations can be configured for the system to
search for the files that contains the runtime image. The locations can be local or remote. The first
location searched is the primary image location. If not found, the secondary image location is
searched, and lastly, the tertiary image location is searched. Figure 5, Figure 6, and Figure 7
describe the bootstrap process.
R
Wait for “wait” seconds
for user key input
Restart
“wait” is
configurable in BOF
Yes
CLI User
connected?
No
If booting after reset-tofactory-default, reset bof
Yes
Booting for first-time
or booting after resetto-factory default ?
No
Auto Mode
A
Boot up
B
Check for Primary/
Secondary/Tertiary
config
Read BOF file for IP
address, static route.
M
Check for
Primary/Secondar
y/ Tertiary Image
T
Configure IP on uplink port
Config file
download
success ?
Yes
No
Manual Mode
TIMOS
Boot-up
Yes
Download Persistence File if
“persist” is ON in BOF
Image download
success?
No
If booting after reset-tofactory-default, reset bof
No
R
bootstrap-updated
flag set and
completed three
attempts
Yes
Set flag to load
golden bootstrap,
and Reboot
Restart
Figure 5: Bootstrap Process - System Initialization - Part II-A
Page 102
7210 SAS D, E OS Basic System Configuration Guide
Boot Option Files
Manual
Mode
M
Restart
R
Ctrl-D
User Login
Successful?
No
Retry User Login
Yes
Provision The BOF Parameters (Few Are Mentioned
Below) (Secondary/Tertiary Parameters Are Optional)
Image And Config Path (Primary/Secondary/Tertiary),
Safe-boot IP, UplinkA (Port, Vlan, IP/Mask, Static-route),
UplinkB (Port, Vlan, IP/Mask, Static-route), Persist.
Save BOF
Successful?
If the IP information needs to be obtained from
DHCP server, IP Address shall be configured
as 0 instead of specifying any IP Address.
DHCP server should grant IP address/mask
and the GW.
Yes
Set Bootflag To
NORMAL_BOOT
No
Old BOF
Present?
Yes
Revert To Old BOF
No
Restart
R
B
OSSG284
Figure 6: Bootstrap Process - System Initialization - Part II-B
7210 SAS D, E OS Basic System Configuration Guide
Page 103
Configuration and Image Loading
Auto
Mode
A
Send DHCP Broadcast Requests On
The Uplink Ports One At A Time
(Designated For Auto-boot)
DHCP
Response Received?
No
R
Restart
R
Restart
Yes
Receive IP, Static-route, BOF Path
In DHCP Response
Configure New IP On The Uplink
Port On Which DHCP Response Was
Received And Download BOF
BOF
Download
Success?
No
Yes
Save
BOF Successful?
No
Yes
Boot
Up
B
OSSG285
Figure 7: Bootstrap Process - System Initialization - Part II-C
When the runtime image is successfully downloaded, control is passed from the bootstrap image.
The runtime image attempts to load the configurations from the downloaded configuration file. If
no configuration file location is present in the BOF file, then the system is loaded with default
configuration. Also during the auto-init, if the configuration file or image file download fails from
the network, then the system is the auto-init procedure.
Page 104
7210 SAS D, E OS Basic System Configuration Guide
Boot Option Files
Ping Check
If the system is booted up using the auto-init procedure, the runtime image performs a ping check
to make sure that the system has IP connectivity. The runtime image, after loading the
configurations from the configuration file, tries three times to ping the IP address specified as the
ping-address parameter in the BOF file, at a 2, 8 and 16 minutes interval minute interval. If the
ping does not succeed, the system is rebooted with BOF reset after 1 minute and the whole boot
process is repeated. If address in the BOF is zero or the ping address is not given, the ping check is
not done. Figure 8 describes the TiMos Boot — System Initialization Part III.
TIMOS
Boot Up
T
Load TIMOS
Bootstrap-updated Flag Set,
Mark It As Success
Apply Downloaded Configuration
Booting For
First-time Or Booting After
Reset-to-factory
Default?
No
BOOT Process Complete.
Send Trap To SNMP.
Issue Trap.
Issue Log Entry.
Issue Console Msg.
Yes
Three Trials
With 5 Mins
Interval
Ping Safe-boot IP If Configured
In BOF
PING Reply
Received For
Safe-boot IP?
No
Reset Factory Default, Reboot
Yes
BOOT Process Complete.
Send Trap To SNMP.
Issue Trap.
Issue Log Entry.
Issue Console Msg.
OSSG286
Figure 8: Timos Boot - System Initialization - Part III
7210 SAS D, E OS Basic System Configuration Guide
Page 105
Configuration and Image Loading
Persistence
The following displays an example of BOF output for 7210 SAS-E devices.
*A:7210>show# bof
===============================================================================
BOF (Memory)
===============================================================================
primary-image ftp://*:*@135.254.170.22//import/panos_builds/nightly/0.0
/I783/STU-sultan
primary-config
ftp://*:*@10.135.25.100/tftpboot/STU/2597-ver2.cfg
secondary-config
tftp://10.135.25.100/STU/2597-ver2.cfg
#eth-mgmt Port Settings:
no eth-mgmt-disabled
eth-mgmt-address
10.135.25.91/24
eth-mgmt-route
10.135.0.0/16 next-hop 10.135.25.1
eth-mgmt-route
135.250.0.0/16 next-hop 10.135.25.1
eth-mgmt-route
135.254.0.0/16 next-hop 10.135.25.1
eth-mgmt-autoneg
eth-mgmt-duplex
full
eth-mgmt-speed
100
#uplinkA Port Settings:
uplinkA-port
1/1/24
uplinkA-address
10.135.25.91/24
uplinkA-vlan
0
uplinkA-route
10.135.0.0/16 next-hop 10.135.25.1
uplinkA-route
135.254.0.0/16 next-hop 10.135.25.1
#uplinkB Port Settings:
uplinkB-port
1/1/2
uplinkB-address
0
uplinkB-vlan
0
#System Settings:
wait
3
persist
off
console-speed
115200
===============================================================================
*A:7210>show#
The following displays an example of BOF output for 7210 SAS D device:
*A:SAS-D>show# bof
===============================================================================
BOF (Memory)
===============================================================================
primary-image
ftp://*:*@135.254.170.22//home/***/images/SASD-both.tim
primary-config
cf1:\****.cfg
#uplinkA Port Settings:
uplinkA-port
1/1/10
uplinkA-address
10.135.20.152/24
uplinkA-vlan
0
uplinkA-route
10.135.0.0/16 next-hop 10.135.20.1
uplinkA-route
135.250.0.0/16 next-hop 10.135.20.1
uplinkA-route
135.254.0.0/16 next-hop 10.135.20.1
#System Settings:
wait
3
Page 106
7210 SAS D, E OS Basic System Configuration Guide
Boot Option Files
persist
off
console-speed
115200
===============================================================================
*A:SAS-D>show#
Optionally, the BOF persist parameter can specify whether the system should preserve system
indexes when a save command is executed. During a subsequent boot, the index file is read along
with the configuration file. As a result, a number of system indexes are preserved between reboots,
including the interface index. If persistence is not required and the configuration file is
successfully processed, then the system becomes operational. If persist is required, then a
matching x.ndx file must be located and successfully processed before the system can become
operational. Matching files (configuration and index files) must have the same filename prefix
such as test123.cfg and test123.ndx and are created at the same time when a save
command is executed. Note that the persistence option must be enabled to deploy the Network
Management System (NMS). The default is off.
Traps, logs, and console messages are generated if problems occur and SNMP shuts down for all
SNMP gets and sets, however, traps are issued.
7210 SAS D, E OS Basic System Configuration Guide
Page 107
Initial System Startup Process Flow
Initial System Startup Process Flow
Figure 12 displays the process start your system. Note that this example assumes that the boot
loader and BOF image and configuration files are successfully located.
START
POWER CYCLE ROUTER
BOOT.TIM FILES FOUND
BOF FILES FOUND
ESTABLISH ROUTER CONNECTION (CONSOLE PORT)
CONFIGURE/MODIFY BOF FILE LOCATIONS
SAVE CONFIG CHANGES
Page 108
PRIMARY IMAGE
PRIMARY CONFIG
SECONDARY IMAGE
SECONDARY CONFIG
TERTIARY IMAGE
TERTIARY CONFIG
7210 SAS D, E OS Basic System Configuration Guide
Boot Option Files
Configuration Notes
•
The loading sequence is based on the order in which it is placed in the configuration file.
It is loaded as it is read in at boot time.
7210 SAS D, E OS Basic System Configuration Guide
Page 109
Configuration Notes
Page 110
7210 SAS D, E OS Basic System Configuration Guide
Boot Option Files
Configuring Boot File Options with CLI
This section provides information to configure BOF parameters with CLI.
Topics in this section include:
•
Configuring Boot File Options with CLI on page 111
•
BOF Configuration Overview on page 112
•
Basic BOF Configuration on page 113
•
Common Configuration Tasks on page 115
•
Configuring BOF Parameters on page 121
•
Service Management Tasks on page 122
→ Viewing the Current Configuration on page 122
→ Modifying and Saving a Configuration on page 124
→ Saving a Configuration to a Different Filename on page 127
→ Rebooting on page 127
7210 SAS D, E OS Basic System Configuration Guide
Page 111
BOF Configuration Overview
BOF Configuration Overview
The boostrap image is loaded from the boot.tim file. The BOF file performs the following tasks:
1.
Sets up the uplink ports (speed, duplex, auto).
2. Assign the IP address (either statically or using DHCP) for the uplink port.
3. Assign the VLAN to the uplink port.
4. Create static routes for the uplink routes.
5. Sets the console port speed.
6. Configures the Domain Name System (DNS) name and DNS servers.
7. Configures the primary, secondary, tertiary configuration source.
8. Configures the primary, secondary, and tertiary image source.
9. Configures operational parameters.
Page 112
7210 SAS D, E OS Basic System Configuration Guide
Boot Option Files
Basic BOF Configuration
The parameters which specify location of the image filename that the router will try to boot from
and the configuration file are in the BOF.
The most basic BOF configuration should have the following:
•
Uplink port parameters
•
Primary image location
•
Primary configuration location
Following is a sample of a basic BOF configuration for 7210 SAS-E devices.
*A:7210>show# bof
===============================================================================
BOF (Memory)
===============================================================================
primary-image ftp://*:*@135.254.170.22//import/panos_builds/nightly/0.0
/I783/STU-sultan
primary-config
ftp://*:*@10.135.25.100/tftpboot/STU/2597-ver2.cfg
secondary-config
tftp://10.135.25.100/STU/2597-ver2.cfg
#eth-mgmt Port Settings:
no eth-mgmt-disabled
eth-mgmt-address
10.135.25.91/24
eth-mgmt-route
10.135.0.0/16 next-hop 10.135.25.1
eth-mgmt-route
135.250.0.0/16 next-hop 10.135.25.1
eth-mgmt-route
135.254.0.0/16 next-hop 10.135.25.1
eth-mgmt-autoneg
eth-mgmt-duplex
full
eth-mgmt-speed
100
#uplinkA Port Settings:
uplinkA-port
1/1/24
uplinkA-address
10.135.25.91/24
uplinkA-vlan
0
uplinkA-route
10.135.0.0/16 next-hop 10.135.25.1
uplinkA-route
135.254.0.0/16 next-hop 10.135.25.1
#uplinkB Port Settings:
uplinkB-port
1/1/2
uplinkB-address
0
uplinkB-vlan
0
#System Settings:
wait
3
persist
off
console-speed
115200
===============================================================================
*A:7210>show#
The following displays an example of BOF output for 7210 SAS D device:
*A:SAS-D>show# bof
===============================================================================
BOF (Memory)
===============================================================================
7210 SAS D, E OS Basic System Configuration Guide
Page 113
Basic BOF Configuration
primary-image
ftp://*:*@135.254.170.22//home/***/images/SASD-both.tim
primary-config
cf1:\****.cfg
#uplinkA Port Settings:
uplinkA-port
1/1/10
uplinkA-address
10.135.20.152/24
uplinkA-vlan
0
uplinkA-route
10.135.0.0/16 next-hop 10.135.20.1
uplinkA-route
135.250.0.0/16 next-hop 10.135.20.1
uplinkA-route
135.254.0.0/16 next-hop 10.135.20.1
#System Settings:
wait
3
persist
off
console-speed
115200
===============================================================================
*A:SAS-D>show#
Page 114
7210 SAS D, E OS Basic System Configuration Guide
Boot Option Files
Common Configuration Tasks
The following sections are basic system tasks that must be performed.
•
Searching for the BOF on page 116
→ Accessing the CLI on page 119
−
•
Console Connection on page 119
Configuring BOF Parameters on page 121
For details about hardware installation and initial router connections, refer to the specific
hardware installation guide.
7210 SAS D, E OS Basic System Configuration Guide
Page 115
Common Configuration Tasks
Searching for the BOF
The BOF should be on the same drive as thebootstrap image file. If the system cannot load or
cannot find the BOF, then the system checks whether the boot sequence was manually interrupted
else continues with the auto-init mode. The system prompts for a different image and
configuration location.
The following example displays an example of the output when the boot sequence is interrupted
for 7210 SAS-E devices.
111Hit a key within 3 seconds to change boot parameters...
Enter password to edit the Boot Options File
Or CTRL-D to exit the prompt
You must supply some required Boot Options. At any prompt, you can type:
"restart" - restart the query mode.
"reboot" - reboot.
"exit"
- boot with with existing values.
"reset"
- reset the bof and reboot.
Press ENTER to begin, or 'flash' to enter firmware update, or the shell password...
Software Location
----------------You must enter the URL of the TiMOS software.
The location can be on a Compact Flash device,
or on the network.
Here are some examples
cf1:/timos1.0R1
ftp://user:[email protected]/./timos1.0R1
ftp://user:passwd@[3FFE::1]/./timos1.0R1
tftp://192.168.1.150/./timos1.0R1
tftp://3FFE::1/./timos1.0R1
The existing Image URL is 'ftp://*:*@10.10.170.22//home/***/images/both.tim'
Press ENTER to keep it.
Software Image URL:
Using: 'ftp://*:*@10.10.170.22//home/****/images/both.tim'
Configuration File Location
--------------------------You must enter the location of configuration
file to be used by TiMOS. The file can be on
a Compact Flash device, or on the network.
Here are some examples
cf1:/config.cfg
ftp://user:[email protected]/./config.cfg
ftp://user:passwd@[3FFE::1]/./config.cfg
tftp://192.168.1.150/./config.cfg
tftp://3FFE::1/./config.cfg
Page 116
7210 SAS D, E OS Basic System Configuration Guide
Boot Option Files
The existing Config URL is 'ftp://*:*@10.135.25.100/tftpboot/STU/config.cfg
Press ENTER to keep it, or the word 'none' for no Config URL.
Config File URL: none
Network Configuration
--------------------Boot Interface Management
------------------------You specified a network location for either the
software or the configuration file. You need to
configure either eth-mgmt or uplinkA or uplinkB ports.
You will be asked to configure the port number, IP address,
static routes, and VLAN Id in case of uplink ports.
eth-mgmt Port Setting
-------------------Existing eth-mgmt port settings are:
eth-mgmt-port
eth-mgmt-address
eth-mgmt-route
eth-mgmt-route
10.135.25.97/24
10.135.0.0/16 next-hop 10.135.25.1
135.254.0.0/16 next-hop 10.135.25.1
eth-mgmt port is configured for Boot Interface Management,
Press ENTER to proceed with existing port settings
Or "disable" to disable the port for Boot Interface Management
Or "edit" to change the port settings:
uplinkA Port Setting
-------------------Existing uplinkA port settings are:
uplinkA-port
uplinkA-address
uplinkA-vlan
1/1/24
0
0
uplinkA port is configured for Boot Interface Management,
Press ENTER to proceed with existing port settings
Or "disable" to disable the port for Boot Interface Management
Or "edit" to change the port settings:
uplinkB Port Setting
-------------------Existing uplinkB port settings are:
uplinkB-port
uplinkB-address
uplinkB-vlan
1/1/2
0
0
uplinkB port is configured for Boot Interface Management,
Press ENTER to proceed with existing port settings
Or "disable" to disable the port for Boot Interface Management
Or "edit" to change the port settings:
New Settings
7210 SAS D, E OS Basic System Configuration Guide
Page 117
Common Configuration Tasks
-----------primary-image
ftp://*:*@135.254.170.22//home/****/images/both.tim
secondary-config
tftp://10.135.25.100/STU/config.cfg
#eth-mgmt Port Settings:
no eth-mgmt-disabled
eth-mgmt-address
10.135.25.97/24
eth-mgmt-route
10.135.0.0/16 next-hop 10.135.25.1
eth-mgmt-route
135.254.0.0/16 next-hop 10.135.25.1
eth-mgmt-autoneg
eth-mgmt-duplex
full
eth-mgmt-speed
100
#uplinkA Port Settings:
uplinkA-port
1/1/24
uplinkA-address
0
uplinkA-vlan
0
#uplinkB Port Settings:
uplinkB-port
1/1/2
uplinkB-address
0
uplinkB-vlan
0
#System Settings:
wait
3
persist
off
console-speed
115200
Page 118
7210 SAS D, E OS Basic System Configuration Guide
Boot Option Files
Accessing the CLI
To access the CLI to configure the software for the first time, follow these steps:
•
When the power to the chassis is turned on, the 7210 SAS software automatically begins
the boot sequence.
•
When the boot loader and BOF image and configuration files are successfully located,
establish a router connection (console session).
Console Connection
To establish a console connection, you will need the following:
•
An ASCII terminal or a PC running terminal emulation software set to the parameters
shown in the table below.
•
A standard serial cable connector for connecting to a RS232 port (provides a RJ45
connector).
Table 14: Console Configuration Parameter Values
Parameter
Value
Baud Rate
115,200
Data Bits
8
Parity
None
Stop Bits
1
Flow Control
None
7210 SAS D, E OS Basic System Configuration Guide
Page 119
Common Configuration Tasks
Figure 9 displays an example of the Console port on a 7210 SAS E front panel.
Console Port
Figure 9: 7210 SAS E Front Panel Console Port
Figure 10 displays an example of the Console port on a 7210 SAS D front panels.
Console Port
AC Power
Console Port
DC Power
Figure 10: 7210 SAS D Front Panel Console Port
To establish a console connection:
Step 1
Connect the terminal to the Console port on the front panel using the serial cable.
Step 2
Power on the terminal.
Step 3
Establish the connection by pressing the <Enter> key a few times on your terminal
keyboard.
Step 4
At the router prompt, enter the login and password.
The default login is admin.
The default password is admin.
Page 120
7210 SAS D, E OS Basic System Configuration Guide
Boot Option Files
Configuring BOF Parameters
The following output displays a BOF configuration for 7210 SAS-E:
*A:7210>show# bof
===============================================================================
BOF (Memory)
===============================================================================
primary-image ftp://*:*@135.254.170.22//import/panos_builds/nightly/0.0
/I783/STU-sultan
primary-config
ftp://*:*@10.135.25.100/tftpboot/STU/2597-ver2.cfg
secondary-config
tftp://10.135.25.100/STU/2597-ver2.cfg
#eth-mgmt Port Settings:
no eth-mgmt-disabled
eth-mgmt-address
10.135.25.91/24
eth-mgmt-route
10.135.0.0/16 next-hop 10.135.25.1
eth-mgmt-route
135.250.0.0/16 next-hop 10.135.25.1
eth-mgmt-route
135.254.0.0/16 next-hop 10.135.25.1
eth-mgmt-autoneg
eth-mgmt-duplex
full
eth-mgmt-speed
100
#uplinkA Port Settings:
uplinkA-port
1/1/24
uplinkA-address
10.135.25.91/24
uplinkA-vlan
0
uplinkA-route
10.135.0.0/16 next-hop 10.135.25.1
uplinkA-route
135.254.0.0/16 next-hop 10.135.25.1
#uplinkB Port Settings:
uplinkB-port
1/1/2
uplinkB-address
0
uplinkB-vlan
0
#System Settings:
wait
3
persist
off
console-speed
115200
===============================================================================
*A:7210>show#
7210 SAS D, E OS Basic System Configuration Guide
Page 121
Service Management Tasks
Service Management Tasks
This section discusses the following service management tasks:
•
System Administration Commands on page 122
→ Viewing the Current Configuration on page 122
→ Modifying and Saving a Configuration on page 124
→ Deleting BOF Parameters on page 125
→ Saving a Configuration to a Different Filename on page 127
System Administration Commands
Use the following administrative commands to perform management tasks.
CLI Syntax: A:ALA-1# admin
check-golden-bootstrap
display-config
reboot [now]
save [file-url] [detail] [index]
update-golden-bootstrap [file-url]
Viewing the Current Configuration
Use one of the following CLI commands to display the current configuration. The detail option
displays all default values. The index option displays only the persistent indices. The info
command displays context-level information.
CLI Syntax: admin# display-config [detail|index]
info detail
The following displays an example of a configuration file:
*A:sim169# admin display-config
# TiMOS-B-0.0.I218 both/i386 ALCATEL SAS-E 7210 Copyright (c) 2000-2008 AlcatelLucent.
# All rights reserved. All use subject to applicable license agreements.
# Built on Fri Sep 26 20:46:58 IST 2008 by panosbld in /panosbld/ws/panos/main
# Generated THU JUN 23 19:19:22 2005 UTC
exit all
configure
#-------------------------------------------------echo "System Configuration"
Page 122
7210 SAS D, E OS Basic System Configuration Guide
Boot Option Files
#-------------------------------------------------system
name "7210-3"
contact "Fred Information Technology"
location "Bldg.1-floor 2-Room 201"
clli-code "abcdefg1234"
coordinates "N 45 58 23, W 34 56 12"
ccm 1
exit
snmp
exit
login-control
idle-timeout 1440
motd text "7210-3"
exit
time
sntp
shutdown
exit
zone UTC
exit
thresholds
rmon
exit
exit
exit...
...
#-------------------------------------------------# Finished FRI Nov 21 15:06:16 2008 UTC
A:*A:sim169##
7210 SAS D, E OS Basic System Configuration Guide
Page 123
Service Management Tasks
Modifying and Saving a Configuration
If you modify a configuration file, the changes remain in effect only during the current power
cycle unless a save command is executed. Changes are lost if the system is powered down or the
router is rebooted without saving.
•
Specify the file URL location to save the running configuration. If a destination is not
specified, the files are saved to the location where the files were found for that boot
sequence. The same configuration can be saved with different file names to the same
location or to different locations.
•
The detail option adds the default parameters to the saved configuration.
•
The index option forces a save of the index file.
•
Changing the active and standby addresses without reboot standby CPM may cause a
boot-env sync to fail.
The following command saves a configuration:
CLI Syntax: bof# save [cflash-id]
Example:
A:ALA-1# bof
A:ALA-1>bof# save cf1:
A:ALA-1>bof#
The following command saves the system configuration:
CLI Syntax: admin# save [file-url] [detail] [index]
Example:
A:ALA-1# admin save cf1:\test123.cfg
Saving config.# Saved to cf1:\test123.cfg
... complete
A:ALA-1#
NOTE: If the persist option is enabled and the admin save file-url command is executed
with an FTP path used as the file-url parameter, two FTP sessions simultaneously open to the
FTP server. The FTP server must be configured to allow multiple sessions from the same login,
otherwise, the configuration and index files will not be saved correctly.
Page 124
7210 SAS D, E OS Basic System Configuration Guide
Boot Option Files
Deleting BOF Parameters
You can delete specific BOF parameters. The no form of these commands removes the parameter
from configuration. The changes remain in effect only during the current power cycle unless a
save command is executed. Changes are lost if the system is powered down or the router is
rebooted without saving.
Deleting the BOF file and then rebooting, causes the system to enter auto mode.
Use the following CLI syntax to save and remove BOF configuration parameters:
CLI Syntax: bof# save [cflash-id]
Example:
A:ALA-1# bof
A:ALA-1>bof# save cf1:
A:ALA-1>bof#
The following is the CLI Syntax for 7210 SAS-E:
CLI Syntax: *A:7210>bof#
no
console-speed
no
dns-domain
no
eth-mgmt-address
no
eth-mgmt-autoneg
no
eth-mgmt-disable
eth-mgmt-duplex
no
eth-mgmt-route
eth-mgmt-speed
persist
no
ping-address
no
primary-config
no
primary-dns
no
primary-image
save
no
secondary-config
no
secondary-dns
no
secondary-image
no
tertiary-config
no
tertiary-dns
no
tertiary-image
no
uplinkA-address
no
uplinkA-port
no
uplinkA-route
no
uplinkA-vlan
no
uplinkB-address
no
uplinkB-port
7210 SAS D, E OS Basic System Configuration Guide
Page 125
Service Management Tasks
no
no
uplinkB-route
uplinkB-vlan
wait
The following is the CLI Syntax for 7210 SAS-D:
CLI Syntax: *A:7210>bof#
no console-speed
no dns-domain
persist
no ping-address
no primary-config
no primary-dns
no primary-image
save
no secondary-config
no secondary-dns
no secondary-image
no tertiary-config
no tertiary-dns
no tertiary-image
no uplinkA-address
no uplinkA-port
no uplinkA-route
no uplinkA-vlan
no uplinkB-address
no uplinkB-port
no uplinkB-route
no uplinkB-vlan
wait
Page 126
7210 SAS D, E OS Basic System Configuration Guide
Boot Option Files
Saving a Configuration to a Different Filename
Save the current configuration with a unique filename to have additional backup copies and to edit
parameters with a text editor. You can save your current configuration to an ASCII file.
Use either of the following CLI syntax to save a configuration to a different location:
CLI Syntax: bof# save [cflash-id]
Example:
A:ALA-1# bof
A:ALA-1>bof# save cf1:
A:ALA-1>bof#
or
CLI Syntax: admin# save [file-url] [detail] [index]
Example:
A:ALA-1>admin# save cf1:\testABC.cfg
Saving config.# Saved to cf1:\testABC.cfg
... complete
A:ALA-1#
Rebooting
When an admin>reboot command is issued, the system reboots. Changes are lost unless the configuration is saved. Use the admin>save file-url command to save the current configuration. The
user is prompted to confirm the reboot operation.
Use the following CLI syntax to reboot:
CLI Syntax: admin# reboot [now]
Example:
A:ALA-1>admin# reboot
A:DutA>admin# reboot
Are you sure you want to reboot (y/n)? y
Resetting...OK
Alcatel-Lucent 7210 Boot ROM. Copyright 2000-2009 Alcatel-Lucent.
All rights reserved. All use is subject to applicable license agreements.
Running POST tests from ROM
Testing ROM load area...done
Relocating code...Jumping to RAM
...
7210 SAS D, E OS Basic System Configuration Guide
Page 127
Service Management Tasks
When an admin reboot auto-init command is issued, the system resets the existing BOF file and
reboots. The system startup process after the admin reboot auto-init command is executed is the
same as the first time system boot as described in System Intialization on page 96.
NOTE: Since the BOF is reset, the system may not boot up withthe last saved system
configuration unless the new BOF file also uses the same configuration file. If it is required that
the system boot up with the last saved system configuration, it is recommended to use the
admin>save file-url command to save the current system configuration and modify the BOF to
use this.
Use the following CLI to reset the BOF and reboot:
CLI Syntax: admin# reboot auto-init [now]
Example: *A:ALA-1# admin reboot auto-init
WARNING: Configuration and/or Boot options may have changed since the last save.
Are you sure you want to reset the bof and reboot (y/n)? Y
Resetting...OK
Alcatel-Lucent 7210 Boot ROM. Copyright 2000-2008 Alcatel-Lucent.
All rights reserved. All use is subject to applicable license agreements.
Page 128
7210 SAS D, E OS Basic System Configuration Guide
Boot Option Files
BOF Command Reference
Command Hierarchies
Configuration Commands
bof
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
console-speed baud-rate
no console-speed
dns-domain dns-name
no dns-domain
[no] eth-mgmt-address ip-prefix/ip-prefix-length (Not supported on 7210 SAS-D)
[no] eth-mgmt-autoneg (Not supported on 7210 SAS-D)
[no] eth-mgmt-address (Not supported on 7210 SAS-D)
[no] eth-mgmt-disable (Not supported on 7210 SAS-D)
eth-mgmt-duplex {full | half} (Not supported on 7210 SAS-D)
[no] eth-mgmt-route <ip-prefix/ip-prefix-length> next-hop <ip-address>(Not supported on 7210
SAS-D)
eth-mgmt-speed speed (Not supported on 7210 SAS-D)
persist {on | off}
ping-address ip-address
no ping-address
primary-config file-url
no primary-config
primary-dns ip-address
no primary-dns
primary-image file-url
no primary-image
save [cflash-id ]
secondary-config file-url
no secondary-config
[no] secondary-dns ip-address
secondary-image file-url
no secondary-image
tertiary-config file-url
no tertiary-config
tertiary-dns ip-address
no tertiary-dns
tertiary-image file-url
no tertiary-image
wait seconds
uplinkA-address ip-address/mask
no uplinkA-address
uplinkA-port port-id
no uplinkA-port
[no] uplinkA-route <ip-address/mask> next-hop <ip-address>
uplinkA-vlan 0..4094
no uplinkA-vlan
uplinkB-address ip-address/mask
no uplinkB-address
uplinkB-port port-id
7210 SAS D, E OS Basic System Configuration Guide
Page 129
BOF Command Reference
—
—
—
—
—
Page 130
no uplinkB-port
[no] uplinkB-route <ip-address/mask> next-hop <ip-address>
uplinkB-vlan 0..4094
no uplinkB-vlan
wait <seconds>
7210 SAS D, E OS Basic System Configuration Guide
Boot Option Files
Show Commands
show
— bof [cflash-id | booted]
— boot-messages
7210 SAS D, E OS Basic System Configuration Guide
Page 131
BOF Command Reference
Page 132
7210 SAS D, E OS Basic System Configuration Guide
Boot Option Files
Configuration Commands
File Management Commands
bof
Syntax
Context
Description
bof
<ROOT>
This command creates or edits the boot option file (BOF) for the specified local storage device.
A BOF file specifies where the system searches for runtime images, configuration files, and other
operational parameters during system initialization.
BOF parameters can be modified. Changes can be saved to a specified compact flash. The BOF must
be located in the root directory of either an internal or external compact flash local to the system and
have the mandatory filename of bof.cfg.
When modifications are made to in-memory parameters that are currently in use or operating, the
changes are effective immediately. For example, if the console-speed is changed, the change takes
place immediately.
Only one entry of the BOF configuration command statement can be saved once the statement has
been found to be syntactically correct.
No default boot option file exists.
Default
none
Syntax
save [cflash-id]
save
Context
Description
bof
This command uses the boot option parameters currently in memory and writes them from the boot
option file to the compact flash.
The BOF is located in the root directory of the internal compact flash drive local to the system and
have the mandatory filename of bof.cfg.
Command usage:
• bof save — Saves the BOF to the flash drive CF1:
• bof save cf1: — Saves the BOF to cf1:
Default
Saves must be explicitly executed. The BOF is saved to cf1: if a location is not specified.
7210 SAS D, E OS Basic System Configuration Guide
Page 133
File Management Commands
Parameters
Page 134
flash-id — The compact flash ID where the bof.cfg is to be saved.
Values
cf1:
Default
cf1:
7210 SAS D, E OS Basic System Configuration
Boot Option Files
BOF Processing Control
wait
Syntax
Context
Description
wait seconds
bof
This command configures a pause, in seconds, at the start of the boot process which allows system
initialization to be interrupted at the console.
When system initialization is interrupted the operator is allowed to manually override the parameters
defined in the boot option file (BOF).
Only one wait command can be defined in the BOF.
Default
Parameters
3
seconds — The time to pause at the start of the boot process, in seconds.
Values
1 — 10
7210 SAS D, E OS Basic System Configuration Guide
Page 135
File Management Commands
Console Port Configuration
console-speed
Syntax
Context
Description
console-speed baud-rate
no console-speed
bof
This command configures the console port baud rate.
When this command is issued while editing the BOF file used for the most recent boot, both the BOF
file and the active configuration are changed immediately.
The no form of the command reverts to the default value.
Default
Parameters
115200 — console configured for 115,200 bps operation
baud-rate — The console port baud rate, expressed as a decimal integer.
Values
Page 136
9600, 19200, 38400, 57600, 115200
7210 SAS D, E OS Basic System Configuration
Boot Option Files
Image and Configuration Management
persist
Syntax
Context
Description
persist {on | off}
bof
This command specifies whether the system will preserve system indexes when a save command is
executed. During a subsequent boot, the index file is read along with the configuration file. As a
result, a number of system indexes are preserved between reboots, including the interface index, etc.
This reduces resynchronizations of the Network Management System (NMS) with the affected
network element.
In the event that persist is on and the reboot with the appropriate index file fails, SNMP is
operationally shut down to prevent the management system from accessing and possibly
synchronizing with a partially booted or incomplete network element. To enable SNMP access, enter
the config>system>snmp>no shutdown command.
If persist is enabled and the admin save <url> command is executed with an FTP path used as the
<url> parameter, two FTP sessions simultaneously open to the FTP server. The FTP server must be
configured to allow multiple sessions from the same login, otherwise, the configuration and index
files will not be saved correctly.
Notes:
• Persistency files (.ndx) are saved on the same disk as the configuration files and the image files.
• When an operator sets the location for the persistency file, the system will check to ensure that
the disk has enough free space. If this there is not enough free space, the persistency will not
become active and a trap will be generated. Then, it is up to the operator to free adequate disk
space. In the meantime, the system will perform a space availability check every 30 seconds. As
soon as the space is available the persistency will become active on the next (30 second) check.
Default
Parameters
off
on — Create when saving the configuration.
off — Disables the system index saves between reboots.
7210 SAS D, E OS Basic System Configuration Guide
Page 137
File Management Commands
primary-config
Syntax
Context
Description
primary-config file-url
no primary-config
bof
This command specifies the name and location of the primary configuration file.
The system attempts to use the configuration specified in primary-config. If the specified file cannot
be located, the system automatically attempts to obtain the configuration from the location specified
in secondary-config and then the tertiary-config.
Note that if an error in the configuration file is encountered, the boot process aborts.
The no form of the command removes the primary-config configuration.
Default
Parameters
none
file-url — The primary configuration file location, expressed as a file URL.
Values
file-url
local-url
remote-url
cflash-id
[local-url | remote-url] (up to 180 characters)
[cflash-id/][file-path]
[{ftp://|tftp://} login:pswd@remote-locn/][file-path]
cf1:
primary-image
Syntax
Context
Description
primary-image file-url
no primary image
bof
This command specifies the primary directory location for runtime image file loading.
The system attempts to load all runtime image files configured in the primary-image first. If this
fails, the system attempts to load the runtime images from the location configured in the secondaryimage. If the secondary image load fails, the tertiary image specified in tertiary-image is used.
The no form of the command removes the primary-image configuration.
Default
Parameters
none
file-url — The location-url can be either local (this CPMflash) or a remote FTP server.
Values
Page 138
file-url
local-url
remote-url
cflash-id
[local-url | remote-url] (up to 180 characters)
[cflash-id/][file-path]
[{ftp://|tftp://} login:pswd@remote-locn/][file-path]
cf1:
7210 SAS D, E OS Basic System Configuration
Boot Option Files
secondary-config
Syntax
Context
Description
secondary-config file-url
no secondary-config
bof
This command specifies the name and location of the secondary configuration file.
The system attempts to use the configuration as specified in secondary-config if the primary config
cannot be located. If the secondary-config file cannot be located, the system attempts to obtain the
configuration from the location specified in the tertiary-config.
Note that if an error in the configuration file is encountered, the boot process aborts.
The no form of the command removes the secondary-config configuration.
Default
Parameters
none
file-url — The secondary configuration file location, expressed as a file URL.
Values
file-url
local-url
remote-url
cflash-id
[local-url | remote-url] (up to 180 characters)
[cflash-id/][file-path]
[{ftp://|tftp://} login:pswd@remote-locn/][file-path]
cf1::
secondary-image
Syntax
Context
Description
secondary-image file-url
no secondary-image
bof
This command specifies the secondary directory location for runtime image file loading.
The system attempts to load all runtime image files configured in the primary-image first. If this
fails, the system attempts to load the runtime images from the location configured in the secondaryimage. If the secondary image load fails, the tertiary image specified in tertiary-image is used.
The no form of the command removes the secondary-image configuration.
Default
Parameters
none
file-url — The file-url can be either local (this CPMlocal flash) or a remote FTP server.
Values
file-url
local-url
remote-url
cflash-id
[local-url | remote-url] (up to 180 characters)
[cflash-id/][file-path]
[{ftp://|tftp://} login:pswd@remote-locn/][file-path]
cf1::
7210 SAS D, E OS Basic System Configuration Guide
Page 139
File Management Commands
tertiary-config
Syntax
Context
Description
tertiary-config file-url
no tertiary-config
bof
This command specifies the name and location of the tertiary configuration file.
The system attempts to use the configuration specified in tertiary-config if both the primary and
secondary config files cannot be located. If this file cannot be located, the system boots with the
factory default configuration.
Note that if an error in the configuration file is encountered, the boot process aborts.
The no form of the command removes the tertiary-config configuration.
Default
Parameters
none
file-url — The tertiary configuration file location, expressed as a file URL.
Values
local-url
cflash-id
remote-url
[cflash-id/][file-path]
cf1:
[{ftp://|tftp://} login:pswd@remote-locn/][file-path]
tertiary-image
Syntax
Context
Description
tertiary-image file-url
no tertiary-image
bof
This command specifies the tertiary directory location for runtime image file loading.
The system attempts to load all runtime image files configured in the primary-image first. If this
fails, the system attempts to load the runtime images from the location configured in the secondaryimage. If the secondary image load fails, the tertiary image specified in tertiary-image is used.
The no form of the command removes the tertiary-image configuration.
Default
Parameters
none
file-url — The location-url can be either local (this flash) or a remote FTP server.
Values
Page 140
file-url
local-url
remote-url
cflash-id
[local-url | remote-url] (up to 180 characters)
[cflash-id/][file-path]
[{ftp://|tftp://} login:pswd@remote-locn/][file-path]
cf1:
7210 SAS D, E OS Basic System Configuration
Boot Option Files
ping-address
Syntax
Context
Description
ping-address ip-address
no ping-address
bof
This command specifies the IP address which would be used for ping-test after the system boots.
The no form of the command removes the ping-address configuration. Setting a value of 0 also
removes the ping-address configuration.
Default
Parameters
none
ip-address — Specifies an IPv4 ip-address in the form a.b.c.d, for example, 10.1.2.10.
uplinkA-address
Syntax
Context
Description
uplinkA-address ip-address/mask
no uplinkA-address
bof
This command configures the uplink-A address.
The no form of the command sets the uplinkA to use DHCP to get the IP and the show bof value
reflects 0 for this parameter.
Parameters
ip-address — The IP address of the Boot Option File (BOF). This address must be unique within the
subnet and specified in dotted decimal notation.
mask — The subnet mask length when the IP prefix is specified in CIDR notation. When the IP prefix
is specified in CIDR notation, a forward slash (/) separates the ip-addr from the mask-length
parameter. The mask length parameter indicates the number of bits used for the network portion
of the IP address; the remainder of the IP address is used to determine the host portion of the IP
address.
Values
1 — 30
uplinkB-address
Syntax
Context
Description
uplinkB-address ip-address/mask
no uplinkB-address
bof
This command configures the uplink-B address.
The no form of the command sets the uplinkB to use DHCP to get the IP and the show bof value
reflects 0 for this parameter.
7210 SAS D, E OS Basic System Configuration Guide
Page 141
File Management Commands
Parameters
ip-address — The IP address of the Boot Option File (BOF). This address must be unique within the
subnet and specified in dotted decimal notation.
mask — The subnet mask length when the IP prefix is specified in CIDR notation. When the IP prefix
is specified in CIDR notation, a forward slash (/) separates the ip-addr from the mask-length
parameter. The mask length parameter indicates the number of bits used for the network portion
of the IP address; the remainder of the IP address is used to determine the host portion of the IP
address.
Values
1 — 30
uplinkA-port
Syntax
Context
Description
uplinkA-port port-id
no uplinkA-port
bof
This command configures the primary port to be used for boot up.
The no form of the command removes all the uplinkA parameters from the BOF.
Parameters
port-id — Specifies the primary port to be used for boot up in the slot/mda/port format.
uplinkB-port
Syntax
Context
Description
uplinkB-port port-id
no uplinkB-port
bof
This command configures the secondary port to be used for boot up.
The no form of the command removes all the uplinkB parameters from the BOF.
Parameters
port-id — Specifies the secondary port to be used for boot up in the slot/mda/port format.
uplinkA-route
Syntax
Context
Description
Page 142
[no] uplinkA-route ip-address/mask next-hop ip-address
bof
This command configures an uplink-A static route.
7210 SAS D, E OS Basic System Configuration
Boot Option Files
Parameters
ip-address — The IP address of the Boot Option File (BOF). This address must be unique within the
subnet and specified in dotted decimal notation.
mask — The subnet mask length when the IP prefix is specified in CIDR notation. When the IP prefix
is specified in CIDR notation, a forward slash (/) separates the ip-addr from the mask-length
parameter. The mask length parameter indicates the number of bits used for the network portion
of the IP address; the remainder of the IP address is used to determine the host portion of the IP
address.
Values
0 — 32
next-hop ip-address — The next hop IP address used to reach the destination.
uplinkB-route
Syntax
Context
[no] uplinkB-route ip-address/mask next-hop ip-address
bof
Description
This command configures an uplink-B static route.
Parameters
ip-address — The IP address of the Boot Option File (BOF). This address must be unique within the
subnet and specified in dotted decimal notation.
mask — The subnet mask length when the IP prefix is specified in CIDR notation. When the IP prefix
is specified in CIDR notation, a forward slash (/) separates the ip-addr from the mask-length
parameter. The mask length parameter indicates the number of bits used for the network portion
of the IP address; the remainder of the IP address is used to determine the host portion of the IP
address.
Values
0 — 32
next-hop ip-address — The next hop IP address used to reach the destination.
uplinkA-vlan
Syntax
Context
Description
uplinkA-vlan 0..4094
no uplinkA-vlan
bof
This command specifies a VLAN ID to be used on uplink-A.
The no form of the command is used to send untagged packets on uplink-A.
7210 SAS D, E OS Basic System Configuration Guide
Page 143
File Management Commands
uplinkB-vlan
Syntax
Context
Description
uplinkB-vlan 0..4094
no uplinkA-vlan
bof
This command specifies a VLAN ID to be used on uplink-B.
The no form of the command is used to send untagged packets on uplink-B.
eth-mgmt-address
Note: This command is not supported on 7210 SAS-D devices.
Syntax
Context
Description
[no] eth-mgmt-address ip-prefix\ip-prefix-length
bof
This command assigns an IP address to the management Ethernet port in the running configuration
and the Boot Option File (BOF). Deleting a BOF address entry is not allowed from a telnet session.
The no form of the command deletes the IP address assigned to the Ethernet port.
Default
Parameters
no eth-mgmt-address — There are no IP addresses assigned to the out-of-band Ethernet
management ports.
ip-prefix\ip-prefix-length — The IP address in dotted decimal notation.
Values
ipv4-prefix a.b.c.d (host bits must be 0)
Values
ipv4-prefix-length 0 — 32
eth-mgmt-autoneg
Note: This command is not supported on 7210 SAS-D devices.
Syntax
Context
Description
[no] eth-mgmt-autoneg
bof
This command enables speed and duplex Auto-negotiation on the management Ethernet port in the
running configuration and the Boot Option File (BOF).
The no form of the command disables the Auto-negotiate feature on this port.
Default
eth-mgmt-autoneg — Auto-negotiation is enabled on the management Ethernet port.
eth-mgmt-disable
Note: This command is not supported on 7210 SAS-D devices.
Page 144
7210 SAS D, E OS Basic System Configuration
Boot Option Files
Syntax
Context
Description
[no] eth-mgmt-disable
bof
This command allows the user to enable or disable the out-of-band management Ethernet port for use
during boot up.
The no form of the command enables the port.
Default
eth-mgmt-disable
eth-mgmt-duplex
Note: This command is not supported on 7210 SAS-D devices.
Syntax
Context
Description
eth-mgmt-duplex {full | half}
bof
This command configures the duplex mode of the management Ethernet port when Auto-negotiation
is disabled in the running configuration and the Boot Option File (BOF).
This configuration command allows for the configuration of the duplex mode of the Ethernet port. If
the port is configured to Auto-negotiate, this parameter will be ignored.
Default
Parameters
eth-mgmt-duplex full — Full duplex operation.
full — Sets the link to full duplex mode.
half — Sets the link to half duplex mode.
eth-mgmt-route
Note: This command is not supported on 7210 SAS-D devices.
Syntax
Context
Description
[no] eth-mgmt-route ip-prefix/ip-prefix-length next-hop ip-address
bof
This command creates a static route entry for the management Ethernet port in the running
configuration and the Boot Option File (BOF).
This command allows manual configuration of static routing table entries. These static routes are only
used by traffic generated by the Ethernet port. To reduce configuration, manual address aggregation
should be applied where possible.
A static default (0.0.0.0 or 0) route cannot be configured on the management Ethernet port. A
maximum of ten static routes can be configured on the management Ethernet port.
The no form of the command deletes the static route.
Default
Parameters
No default routes are configured.
ip-prefix\ip-prefix-length — The destination address of the static route in dotted decimal notation.
7210 SAS D, E OS Basic System Configuration Guide
Page 145
File Management Commands
100 — The destination address of the static route in dotted decimal notation.
Values
ip-prefix|ip-prefix-length: ipv4-prefix a.b.c.d (host bits must be zero) ipv4-prefix-le
0 — 32
Values
Values mask — The subnet mask, expressed as an integer or in dotted decimal
notation. 1 — 32 (mask length), 128.0.0.0 — 255.255.255.255 (dotted decimal)
next-hop ip-address — The next hop IP address used to reach the destination.
The destination address of the static route in dotted decimal notation.
eth-mgmt-speed
Note: This command is not supported on 7210 SAS-D devices.
Syntax
Context
Description
speed speed
bof
This command configures the speed for the management Ethernet port when Auto-negotiation is
disabled in the running configuration and the Boot Option File (BOF).
If the port is configured to Auto-negotiate, this parameter is ignored.
Default
Parameters
speed 100 — 100 M/bps operation.
10 — Sets the link to 10 M/bps speed.
100 — Sets the link to 100 M/bps speed.
active | standby — Specifies which CPM Ethernet address is being configured: the active CPM
Ethernet or the standby CPM Ethernet.
Default
active
next-hop ip-address — The next hop IP address used to reach the destination.
Page 146
7210 SAS D, E OS Basic System Configuration
Boot Option Files
DNS Configuration Commands
dns-domain
Syntax
Context
Description
dns-domain dns-name
no dns-domain
bof
This command configures the domain name used when performing DNS address resolution. This is a
required parameter if DNS address resolution is required. Only a single domain name can be
configured. If multiple domain statements are configured, the last one encountered is used.
The no form of the command removes the domain name from the configuration.
Default
Parameters
no dns-domain — No DNS domain name is configured.
dns-name — Specifies the DNS domain name up to 32 characters in length.
primary-dns
Syntax
Context
Description
primary-dns ip-address
no primary-dns
bof
This command configures the primary DNS server used for DNS name resolution. DNS name
resolution can be used when executing ping, traceroute, and service-ping, and also when defining file
URLs. DNS name resolution is not supported when DNS names are embedded in configuration files.
The no form of the command removes the primary DNS server from the configuration.
Default
Parameters
no primary-dns — No primary DNS server is configured.
ip-address — The IP address of the primary DNS server.
Values
ipv4-address - a.b.c.d
secondary-dns
[no] secondary-dns ip-address
Context
Description
bof
This command configures the secondary DNS server for DNS name resolution. The secondary DNS
server is used only if the primary DNS server does not respond.
7210 SAS D, E OS Basic System Configuration Guide
Page 147
File Management Commands
DNS name resolution can be used when executing ping, traceroute, and service-ping, and also when
defining file URLs. DNS name resolution is not supported when DNS names are embedded in
configuration files.
The no form of the command removes the secondary DNS server from the configuration.
Default
Parameters
no secondary-dns — No secondary DNS server is configured.
ip-address — The IP address of the secondary DNS server.
Values
ipv4-address - a.b.c.d
tertiary-dns
Syntax
Context
Description
tertiary-dns ip-address
no tertiary-dns
bof
This command configures the tertiary DNS server for DNS name resolution. The tertiary DNS server
is used only if the primary DNS server and the secondary DNS server do not respond.
DNS name resolution can be used when executing ping, traceroute, and service-ping, and also when
defining file URLs. DNS name resolution is not supported when DNS names are embedded in
configuration files.
The no form of the command removes the tertiary DNS server from the configuration.
Default
Parameters
no tertiary-dns — No tertiary DNS server is configured.
ip-address — The IP address of the tertiary DNS server.
Values
Page 148
ipv4-address - a.b.c.d
7210 SAS D, E OS Basic System Configuration
Boot Option Files
Show Commands
bof
Syntax
Context
Description
bof [cflash-id | booted]
show
This command displays the Boot Option File (BOF) executed on last system boot or on the specified
device.
If no device is specified, the BOF used in the last system boot displays. If the BOF has been modified
since the system boot, a message displays.
Parameters
cflash-id. The cflash directory name.
Values
cf1:
booted — Displays the boot option file used to boot the system.
Output
Show BOF Fields — The following table describes BOF output fields.
Table 15: Show BOF Output Fields
Label
Description
primary-image
The primary location of the directory that contains the runtime images
of both CPM and IOM.
primary-config
The primary location of the file that contains the configuration.
primary-dns
The primary DNS server for resolution of host names to IP addresses.
secondary-image
The secondary location of the directory that contains the runtime
images of both CPM and IOM.
secondary-config
The secondary location of the file that contains the configuration.
secondary-dns
The secondary DNS server for resolution of host names to IP
addresses.
tertiary-image
The tertiary location of the directory that contains the runtime images
of both CPM and IOM.
tertiary-config
The tertiary location of the file that contains the configuration.
tertiary-dns
The tertiary DNS server for resolution of host names to IP addresses.
persist
on — Persistent indexes between system reboots is enabled.
off — Persistent indexes between system reboots is disabled.
wait
The time configured for the boot to pause while waiting for console
input.
7210 SAS D, E OS Basic System Configuration Guide
Page 149
Show Commands
Table 15: Show BOF Output Fields (Continued)
Label
Description
autonegotiate
No autonegotiate — Autonegotiate not enabled.
autonegotiate — Autonegotiate is enabled.
console speed
The console port baud rate.
ping-address
The IPv4 IP address to be used for ping-test after auto-init.
dns domain
The domain name used when performing DNS address resolution.
uplinkA-address
Displays the Uplink-A IP address.
uplinkA-port
Displays the primary port to be used for auto-boot.
uplinkA-route
Displays the static route associated with Uplink-A.
uplinkA-vlan
Displays the VLAN ID to be used on Uplink-A.
uplinkB-address
Displays the Uplink-B IP address.
uplinkB-port
Displays the secondary port to be used for auto-boot.
uplinkB-route
Displays the static route associated with Uplink-B.
uplinkB-vlan
Displays the VLAN ID to be used on Uplink-B.
.
Table 16: Show BOF Output Fields (supported only on 7210 SAS-E)
Label
Description
eth-mgmt-disabled
Displays if Ethernet management is disabled.
eth-mgmt-addressg
Displays the Ethernet management address.
eth-mgmt-route
Displays the Ethernet Management route.
eth-mgmt-autoneg
Displays if the auto-negotiate is enabled.
eth-mgmt-duplex
Displays the mode of the Ethernet management port.
eth-mgmt-speed
Displays the Ethernet management speed.
Sample Output:
*A:ALA# show bof cf1:
===============================================================================
BOF on cf1:
===============================================================================
primary-image
ftp://*:*@10.135.16.90/./images/auto-boot/solution/bothx.tim
secondary-image
ftp://*:*@10.135.16.90/./images/auto-boot/solution/bothx.tim
Page 150
7210 SAS D, E OS Basic System Configuration Guide
Boot Option Files
tertiary-image
ftp://*:*@10.135.16.90/./images/auto-boot/solution/both.tim
primary-dns
135.254.244.204
dns-domain
in.lucent.com
ping 10.135.16.90
#uplinkA Port Settings:
uplinkA-port
1/1/1
uplinkA-address
192.168.1.11/24
uplinkA-vlan
0
uplinkA-route
10.135.0.0/16 next-hop 192.168.1.1
#uplinkB Port Settings:
uplinkB-port
1/1/2
uplinkB-address
0
uplinkB-vlan
0
#System Settings:
wait
3
persist
on
console-speed
115200
===============================================================================
*A:ALA#
*A:ALA# show bof booted
===============================================================================
System booted with BOF
===============================================================================
primary-image
ftp://*:*@10.135.16.90/./images/auto-boot/solution/bothx.tim
secondary-image
ftp://*:*@10.135.16.90/./images/auto-boot/solution/bothx.tim
tertiary-image
ftp://*:*@10.135.16.90/./images/auto-boot/solution/both.tim
primary-dns
135.254.244.204
dns-domain
in.lucent.com
ping-address
10.135.16.90
#uplinkA Port Settings:
uplinkA-port
1/1/1
uplinkA-address
192.168.1.11/24
uplinkA-vlan
0
uplinkA-route
10.135.0.0/16 next-hop 192.168.1.1
#uplinkB Port Settings:
uplinkB-port
1/1/2
uplinkB-address
0
uplinkB-vlan
0
#System Settings:
wait
3
persist
on
console-speed
115200
===============================================================================
*A:ALA#
7210 SAS D, E OS Basic System Configuration Guide
Page 151
Show Commands
boot-messages
Syntax
Context
Description
Output
boot-messages
show
This command displays boot messages generated during the last system boot.
Show Boot Messages Fields — The following output shows boot message output fields.
Sample Output
===============================================================================
cf1:/bootlog.txt
===============================================================================
Bootlog started for Version V-0.0.I317
Build V-0.0.I317 bootrom/mpc 7xxx
Built on Tue Jan 6 02:23:14 IST 2009 by panosbld in /panosbld/ws/panos/main
?Attempting to load from file cf1:/boot.tim
Version L-0.0.I312, Fri Jan 2 04:26:32 IST 2009 by panosbld in /panosbld/ws/panos/
main
text:(3002475-->12623392) + data:(550940-->2414128)
Starting at 0xb000000...
Total Memory: 512MB Chassis Type: sas
TiMOS-L-0.0.I312 boot/mpc ALCATEL SAS-E
All rights reserved. All use subject to
Built on Fri Jan 2 04:26:32 IST 2009 by
Card Type: badami_7210
7210 Copyright (c) 2000-2009 Alcatel-Lucent.
applicable license agreements.
panosbld in /panosbld/ws/panos/main
TiMOS BOOT LOADER
Extended checks enabled with overhead of 36B
Time from clock is THU JAN 08 16:04:05 2009 UTC
Switching serial output to sync mode...
done
Looking for cf1:/bof.cfg ... OK, reading
Contents of Boot Options File on cf1:
primary-image
ftp://*:*@192.168.170.22/import/panos_nightly_builds/1.0/B112/STU-sultan/both.tim
primary-config
cf1:\config.cfg
#uplinkA Port Settings:
uplinkA-port
1/1/13
uplinkA-address
10.135.17.246/24
uplinkA-vlan
null
uplinkA-route
10.135.0.0/16 next-hop 10.135.17.1
uplinkA-route
192.168.0.0/16 next-hop 10.135.17.1
#uplinkB Port Settings:
uplinkB-port
1/1/2
uplinkB-address
0
uplinkB-vlan
0
#System Settings:
wait
3
persist
off
console-speed
115200
Hit a key within 1 second to change boot parms...
Page 152
7210 SAS D, E OS Basic System Configuration Guide
Boot Option Files
Configuring Network with uplinkA Port Setting.....
Primary config file present at: cf1:\config.cfg
Primary image location: ftp://*:*@192.168.170.22/import/panos_nightly_builds/1.0/B112/STU-sultan/both.tim
Initializing uplinkA port using IP addr 10.135.17.246.
Loading image ftp://*:*@192.168.170.22/import/panos_nightly_builds/1.0/B1-12/STUsultan/both.tim
Version B-1.0.B1-12, Wed Jan 7 00:58:35 IST 2009 by builder in /builder/ws/panos/
main
text:(27022791-->84574868) + data:(1921023-->10720420)
Executing TiMOS image at 0x100000
Total Memory: 512MB Chassis Type: sas
TiMOS-B-1.0.B1-12 both/mpc ALCATEL 7210
All rights reserved. All use subject to
Built on Wed Jan 7 00:58:35 IST 2009 by
Card Type: badami_7210
Copyright (c) 2000-2009 Alcatel-Lucent.
applicable license agreements.
builder in /builder/ws/panos/main
___
___
___
___
/\ \
/\__\
/\ \
/\ \
\:\ \
___
/::| |
/::\ \
/::\ \
\:\ \
/\__\
/:|:| |
/:/\:\ \
/:/\ \ \
/::\ \
_\/__/ /:/|:|__|__
/:/ \:\ \
_\:\~\ \ \
/:/\:\__\ /\__\
/:/ |::::\__\ /:/__/ \:\__\ /\ \:\ \ \__\
/:/ \/__/ /:/ /
\/__/~~/:/ / \:\ \ /:/ / \:\ \:\ \/__/
/:/ /
/:/ /
/:/ /
\:\ /:/ /
\:\ \:\__\
\/__/
\/__/
/:/ /
\:\/:/ /
\:\/:/ /
/:/ /
\::/ /
\::/ /
\/__/
\/__/
\/__/
Time from clock is THU JAN 08 16:05:20 2009 UTC
Attempting to exec primary configuration file:
'cf1:\config.cfg' ...
System Configuration
System Security Configuration
Log Configuration
System Security Cpm Hw Filters Configuration
QoS Slope and Queue Policies Configuration
Port Scheduler Policies Configuration
Card Configuration
Port Configuration
Management Router Configuration
Router (Network Side) Configuration
Static Route Configuration
Service Configuration
Router (Service Side) Configuration
Executed 234 lines in 0.1 seconds from file cf1:\config.cfg
INFO: CLI #1008 The SNMP daemon is disabled. To enable SNMP, execute the command
'config>system>snmp no shutdown'.
TiMOS-B-1.0.B1-12 both/mpc ALCATEL SAS-E 7210 Copyright (c) 2000-2008 Alcatel-Lucent.
All rights reserved. All use subject to applicable license agreements.
Built on Wed Jan 7 00:58:35 IST 2009 by builder in /builder/ws/panos/main
Login:
7210 SAS D, E OS Basic System Configuration Guide
Page 153
Show Commands
Page 154
7210 SAS D, E OS Basic System Configuration Guide
System Management
In This Chapter
This chapter provides information about configuring basic system management parameters.
Topics in this chapter include:
•
System Management Parameters on page 156
→ System Information on page 156
−
System Name on page 156
−
System Contact on page 156
−
System Location on page 157
−
System Coordinates on page 157
−
Naming Objects on page 157
−
Naming Objects on page 157
→ System Time on page 159
•
−
Time Zones on page 159
−
Network Time Protocol (NTP) on page 161
−
SNTP Time Synchronization on page 162
−
CRON on page 163
High Availability on page 164
→ HA Features on page 164
−
HA Features on page 164
•
Redundancy on page 164
7210 SAS D, E OS Basic System Configuration Guide
Page 155
System Management Parameters
System Management Parameters
System management commands allow you to configure basic system management functions such
as the system name, the router’s location and coordinates, and CLLI code as well as time zones,
Network Time Protocol (NTP), Simple Network Time Protocol (SNTP) properties, CRON and
synchronization properties.
System Information
System information components include:
•
System Name on page 156
•
System Contact on page 156
•
System Location on page 157
•
System Coordinates on page 157
•
Naming Objects on page 157
System Name
The system name is the MIB II (RFC 1907, Management Information Base for Version 2 of the
Simple Network Management Protocol (SNMPv2)) sysName object. By convention, this text
string is the node’s fully-qualified domain name. The system name can be any ASCII printable
text string of up to 32 characters.
System Contact
The system contact is the MIB II sysContact object. By convention, this text string is a textual
identification of the contact person for this managed node, together with information on how to
contact this person.The system contact can be any ASCII printable text string of up to 80
characters.
Page 156
7210 SAS D, E OS Basic System Configuration Guide
System Management
System Location
The system location is the MIB II sysLocation object which is a text string conventionally used to
describe the node’s physical location, for example, “Bldg MV-11, 1st Floor, Room 101”. The
system location can be any ASCII printable text string of up to 80 characters.
System Coordinates
The system coordinates is the Alcatel-Lucent Chassis MIB tmnxChassisCoordinates object. This
text string indicates the Global Positioning System (GPS) coordinates of the location of the
chassis.
Two-dimensional GPS positioning offers latitude and longitude information as a four dimensional
vector:
⟨ direction, hours, minutes, sec onds⟩
where direction is one of the four basic values: N, S, W, E, hours ranges from 0 to 180 (for
latitude) and 0 to 90 for longitude, and minutes and seconds range from 0 to 60.
<W, 122, 56, 89> is an example of longitude and <N, 85, 66, 43> is an example of latitude.
System coordinates can be expressed in different notations, examples include:
•
N 45 58 23, W 34 56 12
•
N37 37' 00 latitude, W122 22' 00 longitude
•
N36*39.246'
W121*40.121
The system coordinates can be any ASCII printable text string up to 80 characters.
Naming Objects
It is discouraged to configure named objects with a name that starts with “_tmnx_” and with “_” in
general.
7210 SAS D, E OS Basic System Configuration Guide
Page 157
System Management Parameters
Common Language Location Identifier
A Common Language Location Identifier (CLLI) code string for the device is an 11-character
standardized geographic identifier that uniquely identifies the geographic location of places and
certain functional categories of equipment unique to the telecommunications industry. The CLLI
code is stored in the Alcatel-Lucent Chassis MIB tmnxChassisCLLICode object.
The CLLI code can be any ASCII printable text string of up to 11 characters.
Page 158
7210 SAS D, E OS Basic System Configuration Guide
System Management
System Time
routers are equipped with a real-time system clock for time keeping purposes. When set, the
system clock always operates on Coordinated Universal Time (UTC), but the software has
options for local time translation as well as system clock synchronization.
System time parameters include:
•
Time Zones on page 159
•
Network Time Protocol (NTP) on page 161
•
SNTP Time Synchronization on page 162
•
CRON on page 163
Time Zones
Setting a time zone in allows for times to be displayed in the local time rather than in UTC. The
has both user-defined and system defined time zones.
A user-defined time zone has a user assigned name of up to four printable ASCII characters in
length and unique from the system-defined time zones. For user-defined time zones, the offset
from UTC is configured as well as any summer time adjustment for the time zone.
The system-defined time zones are listed in Table 17 which includes both time zones with and
without summer time correction.
Table 17: System-defined Time Zones
Acronym
Time Zone Name
UTC Offset
Europe:
GMT
Greenwich Mean Time
UTC
BST
British Summer Time
UTC +1
IST
Irish Summer Time
UTC +1*
WET
Western Europe Time
UTC
WEST
Western Europe Summer Time
UTC +1
CET
Central Europe Time
UTC +1
CEST
Central Europe Summer Time
UTC +2
EET
Eastern Europe Time
UTC +2
EEST
Eastern Europe Summer Time
UTC +3
7210 SAS D, E OS Basic System Configuration Guide
Page 159
System Management Parameters
Table 17: System-defined Time Zones (Continued)
Acronym
Time Zone Name
UTC Offset
MSK
Moscow Time
UTC +3
MSD
Moscow Summer Time
UTC +4
US and Canada
AST
Atlantic Standard Time
UTC -4
ADT
Atlantic Daylight Time
UTC -3
EST
Eastern Standard Time
UTC -5
EDT
Eastern Daylight Saving Time
UTC -4
ET
Eastern Time
Either as EST or EDT, depending on
place and time of year
CST
Central Standard Time
UTC -6
CDT
Central Daylight Saving Time
UTC -5
CT
Central Time
Either as CST or CDT, depending
on place and time of year
MST
Mountain Standard Time
UTC -7
MDT
Mountain Daylight Saving Time
UTC -6
MT
Mountain Time
Either as MST or MDT, depending
on place and time of year
PST
Pacific Standard Time
UTC -8
PDT
Pacific Daylight Saving Time
UTC -7
PT
Pacific Time
Either as PST or PDT, depending on
place and time of year
HST
Hawaiian Standard Time
UTC -10
AKST
Alaska Standard Time
UTC -9
AKDT
Alaska Standard Daylight Saving Time
UTC -8
AWST
Western Standard Time (e.g., Perth)
UTC +8
ACST
Central Standard Time (e.g., Darwin)
UTC +9.5
AEST
Eastern Standard/Summer Time (e.g.,
Canberra)
UTC +10
Australia
Page 160
7210 SAS D, E OS Basic System Configuration Guide
System Management
Network Time Protocol (NTP)
NTP is the Network Time Protocol defined in RFC 1305, Network Time Protocol (Version 3)
Specification, Implementation and Analysis. It allows for the participating network nodes to keep
time more accurately and more importantly they can maintain time in a more synchronized fashion
between all participating network nodes.
NTP uses stratum levels to define the number of hops from a reference clock. The reference clock
is considered to be a stratum-0 device that is assumed to be accurate with little or no delay.
Stratum-0 servers cannot be used in a network. However, they can be directly connected to
devices that operate as stratum-1 servers. A stratum-1 server is an NTP server with a directlyconnected device that provides Coordinated Universal Time (UTC), such as a GPS or atomic
clock. The 7210 SAS E device cannot act as stratum-1 servers but can act as stratum-2 devices as
a network connection to an NTP server is required.
The higher stratum levels are separated from the stratum-1 server over a network path, thus, a
stratum-2 server receives its time over a network link from a stratum-1 server. A stratum-3 server
receives its time over a network link from a stratum-2 server.
The following NTP elements are supported:
•
Server mode — In this mode, the node advertises the ability to act as a clock source for
other network elements. In this mode, the node will, by default, transmit NTP packets in
NTP version 4 mode.
•
Authentication keys — Increased security support in carrier and other network has been
implemented. Both DES and MD5 authentication are supported as well as multiple keys.
•
Operation in symmetric active mode — This capability requires that NTP be synchronized
with a specific node that is considered more trustworthy or accurate than other nodes
carrying NTP in the system. This mode requires that a specific peer is set.
•
Broadcastmode — When operating in this mode, the node will receive or send using a
broadcast address.
•
Alert when NTP server is not available — When none of the configured servers are
reachable on the node, the system reverts to manual timekeeping and issues a critical
alarm. When a server becomes available, a trap is issued indicating that standard operation
has resumed.
•
NTP and SNTP — If both NTP and SNTP are enabled on the node, then SNTP transitions
to an operationally down state. If NTP is removed from the configuration or shut down,
then SNTP resumes an operationally up state.
•
Gradual clock adjustment — As several applications (such as Service Assurance Agent
(SAA)) can use the clock, and if determined that a major (128 ms or more) adjustment
needs to be performed, the adjustment is performed by programmatically stepping the
clock. If a minor (less than 128 ms) adjustment must be performed, then the adjustment is
performed by either speeding up or slowing down the clock.
7210 SAS D, E OS Basic System Configuration Guide
Page 161
System Management Parameters
•
In order to avoid the generation of too many events/trap the NTP module will rate limit the
generation of events/traps to three per second. At that point a single trap will be generated
that indicates that event/trap squashing is taking place.
SNTP Time Synchronization
For synchronizing the system clock with outside time sources, the 7210 SAS OS software includes
a Simple Network Time Protocol (SNTP) client. As defined in RFC 2030, SNTP Version 4 is an
adaptation of the Network Time Protocol (NTP). SNTP typically provides time accuracy within
100 milliseconds of the time source. SNTP can only receive the time from NTP servers; it cannot
be used to provide time services to other systems. SNTP is a compact, client-only version of NTP.
SNTP does not authenticate traffic.
SNTP can be configured in both unicast client modes (point-to-point) and broadcast client modes
(point-to-multipoint). SNTP should be used only at the extremities of the synchronization subnet.
SNTP clients should operate only at the highest stratum (leaves) of the subnet and in
configurations where no NTP or SNTP client is dependent on another SNTP client for
synchronization. SNTP time servers should operate only at the root (stratum 1) of the subnet and
then only in configurations where no other source of synchronization other than a reliable radio
clock is available.
In the 7210 SAS OS software, the SNTP client can be configured for either broadcast or unicast
client mode.
Page 162
7210 SAS D, E OS Basic System Configuration Guide
System Management
CRON
The CRON feature supports the Service Assurance Agent (SAA) functions as well as the ability to
schedule turning on and off policies to meet “Time of Day” requirements. CRON functionality
includes the ability to specify the commands that need to be run, when they will be scheduled,
including one-time only functionality (oneshot), interval and calendar functions, as well as where
to store the output of the results. In addition, CRON can specify the relationship between input,
output and schedule. Scheduled reboots, peer turn ups, service assurance agent tests and more can
all be scheduled with Cron, as well as OAM events, such as connectivity checks, or
troubleshooting runs.
CRON features are saved to the configuration file.
CRON features run serially with at least 255 separate schedules and scripts. Each instance can
support a schedule where the event is executed any number of times.
The following CRON elements are supported:
•
Action — Parameters for a script including the maximum amount of time to keep the
results from a script run, the maximum amount of time a script may run, the maximum
number of script runs to store and the location to store the results.
•
Schedule — The schedule function configures the type of schedule to run, including onetime only (oneshot), periodic or calendar-based runs. All runs are determined by month,
day of month or weekday, hour, minute and interval (seconds).
•
Script — The script command opens a new nodal context which contains information on a
script.
•
Time Range — ACLs and QoS policy configurations may be enhanced to support time
based matching. CRON configuration includes time matching with the 'schedule' subcommand. Schedules are based on events; time-range defines an end-time used as a match
criteria.
•
Time of Day — Time of Day (TOD) suites are useful when configuring many types of
time-based policies or when a large number of SAPs require the same type of TOD
changes. The TOD suite may be configured while using specific ingress or egress ACLs
or QoS policies, and is an enhancement of the ingress and egress CLI trees.
7210 SAS D, E OS Basic System Configuration Guide
Page 163
High Availability
High Availability
This section discusses the high availability (HA) routing options and features available to service
providers that help diminish vulnerability at the network or service provider edge and alleviate the
effect of a lengthy outage on IP networks.
High availability is an important feature in service provider routing systems. High availability is
gaining momentum due to the unprecedented growth of IP services and applications in service
provider networks driven by the demand from the enterprise and residential communities.
Downtime can be very costly, and, in addition to lost revenue, customer information and businesscritical communications can be lost. High availability is the combination of continuous uptime
over long periods (Mean Time Between Failures (MTBF)) and the speed at which failover or
recovery occurs (Mean Time To Repair (MTTR).
The popularity of high availability routing is evident at the network or service provider edge where
thousands of connections are hosted and rerouting options around a failed piece of equipment can
often be limiting. Or, a single access link exists to a customer because of additional costs for
redundant links. As service providers converge business-critical services such as real-time voice
(VoIP), video, and VPN applications over their IP networks, high availability becomes much more
stringent compared to the requirements for best-effort data. Network and service availability
become critical aspects when offering advanced IP services which dictates that IP routers that are
used to construct the foundations of these networks be resilient to component and software
outages.
HA Features
As more and more critical commercial applications move onto the IP networks, providing high
availability services becomes increasingly important. This section describes high availability
features for devices.
•
Redundancy on page 164
→ Component Redundancy on page 165
Redundancy
The redundancy features enable the duplication of data elements to maintain service continuation
in case of outages or component failure.
Page 164
7210 SAS D, E OS Basic System Configuration Guide
System Management
Component Redundancy
7210 SAS-Series component redundancy is critical to reduce MTTR for the system and primarily
consists of the following features for 7210 SAS-E devices:
•
Redundant power supply — A power module can be removed without impact on traffic.
•
Fan module — The fan module contains three fans. Failure of one or more fans does not
impact traffic.
•
Hot swap — The power supply and fan module supports hot swapping.
For 7210 SAS-D devices:
•
7210 SAS-D has an integrated AC or DC power supply. Redundant external backup
power supply is available only on 7210 SAS D ETR variant.
•
Fan module — 7210 SAS-D devices do not have a fan, therefore supports only passive
cooling.
•
Hot swap — Power supply integrated into chassis. Hot swapping is not supported.
7210 SAS D, E OS Basic System Configuration Guide
Page 165
High Availability
Temperature Threshold Alarm and Fan Speed
In the 7210 SAS E device, if the chassis temperature crosses a threshold of 58 degrees centigrade ,
the system raises an software alarm for over-termperature. When the temperature reduces below
58C, the over-temperature alarm is cleared by the system.
The fan operates at two speeds- half speed and full speed. When the temperature of the chassis
raises above 42 degrees centigrade the fan speed changes to full speed and when the temperature
reduces to 37 degrees centigrade, the fan speed changes to half speed.
The 7210 SAS-D devices do not support any alarm contact outputs, hence when the system raises
an alarm it is only logged. The system status LED is used to indicate an alarm in applicable cases.
Listed below in table X are the temperature thresholds for 7210 SAS-D devices:
.
Table 18: Temperature Thresholds for 7210 SAS-D Devices
Device Variants
Min. Temperature
(in degree centigrade)
Max. Temperature
(in degree centigrade)
7210 SAS-D
0
45
7210 SAS-D ETR
-30
60
The temperature threshold is measured by the sensors inside the chassis and is typically more than
the aisle ambient temperature.The threshold temperature is not user configurable.
Over-temperature is alarm raised when the temperature of the device exceeds 45 in degree
centigrade in 7210 SAS-D 6T4F and 60 in degree centigrade in 7210 SAS-D 6T4F ETR variant.
Note: 7210 SAS-D devices do not have a fan therefore only passive cooling is supported.
Page 166
7210 SAS D, E OS Basic System Configuration Guide
System Management
Link Layer Discovery Protocol (LLDP)
The IEEE 802.1ab Link Layer Discovery Protocol (LLDP) is a uni-directional protocol that uses
the MAC layer to transmit specific information related to the capabilities and status of the local
device. The LLDP can send as well as receive information from a remote device stored in the
related MIB(s).
The LLDP does not contain a mechanism to solicit information received from other LLDP agents.
The protocol also does not provide means to confirm the receipt of information. LLDP provides
the flexibility of enabling a transmitter and receiver separately, therefore the following LLDP
configurations are allowed:
•
An LLDP agent can only transmit information.
•
An LLDP agent can only receive information.
•
An LLDP agent can transmit and receive information.
The information fields in each LLDP frame are contained in an LLDP Data Unit (LLDPDU) as a
sequence of variable length information elements. Each information element includes Type,
Length, and Value fields (TLVs).
•
Type indicates the nature of information being transmitted.
•
Length indicates the length of the information string in octets.
•
Value is the actual information that is transmitted. (For example, a binary bit map or an
alphanumeric string that can contain one or more fields).
Each LLDPDU contains four mandatory TLVs and optional TLVs selected by the Network
Management. Below is the format of a LLDPDU:
•
Chassis ID TLV
•
Port ID TLV
•
Time To Live TLV
•
Zero or more optional TLVs, depending on the maximum size of the LLDPDU allowed.
•
End Of LLDPDU TLV
An LLDP agent or port is identified by a concatenated string formed by the Chassis ID TLV and
the Port ID TLV. This string is used by a recipient to identify an LLDP port or agent. The
combination of the Port ID and Chassis ID TLVs remains unchanged until the port or agent is
operational.
The TTL (Time To Live) field of an Time-To-Live TLV can be either zero or a non-zero value. A
zero value in the TTL field notifies the receiving LLDP agent to immediately discard all
information related to the sending LLDP agent. A non-zero value in the TTL field indicates the
time duration for which the receiving LLDP agent should retain the sending LLDP agent’s
7210 SAS D, E OS Basic System Configuration Guide
Page 167
Link Layer Discovery Protocol (LLDP)
information. The receiving LLDP agent discards all information related to the sending LLDP
agent after the time interval indicated in the TTL field is complete.
Note: A TTL value of zero can be used to signal that the sending LLDP port has initiated a port
shutdown procedure.
The End Of LLDPDU TLV indicates the end of the LLDPDU.
Listed below is the information included in the protocol defined by the IEEE 802.1ab standard:
Page 168
•
Connectivity and management information about the local station to adjacent stations on
the same IEEE 802 LAN is advertised.
•
Network management information from adjacent stations on the same IEEE 802 LAN is
received.
•
Operates with all IEEE 802 access protocols and network media.
•
Network management information schema and object definitions that suitable for storing
connection information about adjacent stations is established.
•
Provides compatibility with a number of MIBs. Refer to Figure 11.
7210 SAS D, E OS Basic System Configuration Guide
System Management
Figure 11: LLDP Internal Architecture for a Network Node
In order to detect and address network problems and inconsistencies in the configuration, the
network operators can discover the topology information using LLDP. The Standard-based tools
address the complex network scenarios where multiple devices from different vendors are
interconnected using Ethernet interfaces.
The example displayed in Figure 12 depicts a MPLS network that uses Ethernet interfaces in the
core or as an access/handoff interfaces to connect to different kind of Ethernet enabled devices
such as service gateway/routers, QinQ switches DSLAMs or customer equipment.
The topology information of the network in Figure 12 can be discovered if, IEEE 802.1ab LLDP
is running on each of the Ethernet interfaces in network.
7210 SAS D, E OS Basic System Configuration Guide
Page 169
Link Layer Discovery Protocol (LLDP)
MPLS/Native ETH
Core
SG/R
SG/R
P
P
LAG
PE
PE
PE
PE
PE
PE
QinQ
SWs
DSLAMs
Ethernet Links - FE/GE/10GE
OSSG263
Figure 12: Customer Use Example For LLDP
Page 170
7210 SAS D, E OS Basic System Configuration Guide
System Management
System Configuration Process Overview
Figure 13 displays the process to provision basic system parameters.
START
CONFIGURE SYSTEM INFORMATION
CONFIGURE TIME PARAMETERS
END
Figure 13: System Configuration and Implementation Flow
7210 SAS D, E OS Basic System Configuration Guide
Page 171
Configuration Notes
Configuration Notes
This section describes system configuration caveats.
General
•
Page 172
The 7210 SAS device must be properly initialized and the boot loader and BOF files
successfully executed in order to access the CLI.
7210 SAS D, E OS Basic System Configuration Guide
System Management
Configuring System Management with CLI
This section provides information about configuring system management features with CLI.
Topics in this chapter include:
•
Basic System Configuration on page 175
•
Common Configuration Tasks on page 176
•
System Information on page 177
→ System Information Parameters
— Name on page 178
— Contact on page 178
— Location on page 179
— CLLI Code on page 179
— Coordinates on page 180
→ System Time Elements on page 181
— Zone on page 181
— Summer Time Conditions on page 183
— NTP on page 184
— SNTP on page 189
— CRON on page 191
•
System Administration Parameters on page 203
→ Validating the Golden Bootstrap Image on page 203
→ Updating the Golden Bootstrap Image on page 204
→ Disconnect on page 204
→ Set-time on page 205
→ Display-config on page 205
→ Tech-support on page 207
→ Save on page 207
→ Reboot on page 208
→ Post-Boot Configuration Extension Files on page 209
•
Configuring System Monitoring Thresholds on page 212
7210 SAS D, E OS Basic System Configuration Guide
Page 173
System Management
System Management
Saving Configurations
Whenever configuration changes are made, the modified configuration must be saved so the
changes will not be lost when the system is rebooted. The system uses the configuration and image
files, as well as other operational parameters necessary for system initialization, according to the
locations specified in the boot option file (BOF) parameters. For more information about boot
option files, refer to the Boot Option Files section of this manual.
Configuration files are saved by executing implicit or explicit command syntax.
•
An explicit save writes the configuration to the location specified in the save command
syntax (the file-url option).
•
An implicit save writes the configuration to the file specified in the primary configuration
location.
If the file-url option is not specified in the save command syntax, the system attempts to
save the current configuration to the current BOF primary configuration source. If the
primary configuration source (path and/or filename) changed since the last boot, the new
configuration source is used.
The save command includes an option to save both default and non-default configuration
parameters (the detail option).
The index option specifies that the system preserves system indexes when a save command is
executed, regardless of the persistent status in the BOF file. During a subsequent boot, the index
file is read along with the configuration file. As a result, a number of system indexes are preserved
between reboots, including the interface index, LSP IDs, path IDs, etc. This reduces
resynchronizations of the Network Management System (NMS) with the affected network
element.
If the save attempt fails at the destination, an error occurs and is logged. The system does not try to
save the file to the secondary or tertiary configuration sources unless the path and filename are
explicitly named with the save command.
Page 174
7210 SAS D, E OS Basic System Configuration Guide
System Management
Basic System Configuration
This section provides information to configure system parameters and provides configuration
examples of common configuration tasks. The minimal system parameters that should be
configured are:
•
System Information Parameters on page 178
•
System Time Elements on page 181
The following example displays a basic system configuration:
A:ALA-12>config>system# info
#-----------------------------------------echo "System Configuration "
#-----------------------------------------name "ALA-12"
coordinates "Unknown"
snmp
exit
security
snmp
community "private" rwa version both
exit
exit
time
ntp
server 192.168.15.221
no shutdown
exit
sntp
shutdown
exit
zone GMT
exit
---------------------------------------------A:ALA-12>config>system#
7210 SAS D, E OS Basic System Configuration Guide
Page 175
Common Configuration Tasks
Common Configuration Tasks
This section provides a brief overview of the tasks that must be performed to configure system
parameters and provides the CLI commands.
•
System Information on page 177
→ Name on page 178
→ Contact on page 178
→ Location on page 179
→ CLLI Code on page 179
→ Coordinates on page 180
•
System Time Elements on page 181
→ Zone on page 181
→ Summer Time Conditions on page 183
→ NTP on page 184
→ SNTP on page 189
→ CRON on page 191
— Time Range on page 194
— Time of Day on page 198
•
System Administration Parameters on page 203
→ Disconnect on page 204
→ Set-time on page 205
→ Display-config on page 205
→ Reboot on page 208
→ Save on page 207
Page 176
7210 SAS D, E OS Basic System Configuration Guide
System Management
System Information
This section covers the basic system information parameters to configure the physical location of
the , contact information, location information such as the place the router is located such as an
address, floor, room number, etc., global positioning system (GPS) coordinates, and system name.
Use the CLI syntax displayed below to configure the following system components:
•
System Information Parameters on page 178
•
System Time Elements on page 181
General system parameters include:
•
Name on page 178
•
Contact on page 178
•
Location on page 179
•
CLLI Code on page 179
•
Coordinates on page 180
7210 SAS D, E OS Basic System Configuration Guide
Page 177
Common Configuration Tasks
System Information Parameters
Name
Use the system command to configure a name for the device. The name is used in the prompt
string. Only one system name can be configured, if multiple system names are configured the last
one encountered overwrites the previous entry. Use the following CLI syntax to configure the
system name:
CLI Syntax: config>system
name system-name
Example:
alcatel>config>system# name ALA-12
The following example displays the system name:
sysName@domain>config>system# info
#-----------------------------------------echo "System Configuration "
#-----------------------------------------name "ALA-12"
. . .
exit
---------------------------------------------sysName@domain>config>system#
Contact
Use the contact command to specify the name of a system administrator, IT staff member, or
other administrative entity.
CLI Syntax: config>system
contact contact-name
Example:
Page 178
config>system# contact “Fred Information Technology”
7210 SAS D, E OS Basic System Configuration Guide
System Management
Location
Use the location command to specify the system location of the device. For example, enter the
city, building address, floor, room number, etc., where the router is located.
Use the following CLI syntax to configure the location:
CLI Syntax: config>system
location location
Example:
config>system# location “Bldg.1-floor 2-Room 201”
CLLI Code
The Common Language Location Code (CLLI code) is an 11-character standardized geographic
identifier that is used to uniquely identify the geographic location of a router.
Use the following CLI command syntax to define the CLLI code:
CLI Syntax: config>system
clli-code clli-code
Example:
config>system# clli-code abcdefg1234
7210 SAS D, E OS Basic System Configuration Guide
Page 179
Common Configuration Tasks
Coordinates
Use the optional coordinates command to specify the GPS location of the device. If the string
contains special characters (#, $, spaces, etc.), the entire string must be enclosed within double
quotes.
Use the following CLI syntax to configure the location:
CLI Syntax: config>system
coordinates coordinates
Example:
config>system# coordinates "N 45 58 23, W 34 56 12"
The following example displays the configuration output of the general system commands:
output
sysName@domain>config>system# info
#-----------------------------------------echo "System Configuration "
#-----------------------------------------name "ALA-12"
contact "Fred Information Technology"
location "Bldg.1-floor 2-Room 201"
clli-code "abcdefg1234"
coordinates "N 45 58 23, W 34 56 12"
. . .
exit
---------------------------------------------A:ALA-12>config>system#
Page 180
7210 SAS D, E OS Basic System Configuration Guide
System Management
System Time Elements
The system clock maintains time according to Coordinated Universal Time (UTC). Configure
information time zone and summer time (daylight savings time) parameters to correctly display
time according to the local time zone.
Time elements include:
•
Zone on page 181
•
Summer Time Conditions on page 183
•
NTP on page 184
•
SNTP on page 189
•
CRON on page 191
→ Time Range on page 194
→ Time of Day on page 198
Zone
The zone command sets the time zone and/or time zone offset for the device. The 7210-SAS OS
supports system-defined and user-defined time zones. The system-defined time zones are listed in
Table 19.
CLI Syntax: config>system>time
zone std-zone-name|non-std-zone-name [hh [:mm]]
Example:
config>system>time#
config>system>time# zone GMT
The following example displays the zone output:
A:ALA-12>config>system>time# info
---------------------------------------------ntp
server 192.168.15.221
no shutdown
exit
sntp
shutdown
exit
zone UTC
---------------------------------------------A:ALA-12>config>system>time#
7210 SAS D, E OS Basic System Configuration Guide
Page 181
Common Configuration Tasks
Table 19: System-defined Time Zones
Acronym
Time Zone Name
UTC Offset
Europe:
GMT
Greenwich Mean Time
UTC
WET
Western Europe Time
UTC
WEST
Western Europe Summer Time
UTC +1 hour
CET
Central Europe Time
UTC +1 hour
CEST
Central Europe Summer Time
UTC +2 hours
EET
Eastern Europe Time
UTC +2 hours
EEST
Eastern Europe Summer Time
UTC +3 hours
MSK
Moscow Time
UTC +3 hours
MSD
Moscow Summer Time
UTC +4 hours
US and Canada:
AST
Atlantic Standard Time
UTC -4 hours
ADT
Atlantic Daylight Time
UTC -3 hours
EST
Eastern Standard Time
UTC -5 hours
EDT
Eastern Daylight Saving Time
UTC -4 hours
CST
Central Standard Time
UTC -6 hours
CDT
Central Daylight Saving Time
UTC -5 hours
MST
Mountain Standard Time
UTC -7 hours
MDT
Mountain Daylight Saving Time
UTC -6 hours
PST
Pacific Standard Time
UTC -8 hours
PDT
Pacific Daylight Saving Time
UTC -7 hours
HST
Hawaiian Standard Time
UTC -10 hours
AKST
Alaska Standard Time
UTC -9 hours
AKDT
Alaska Standard Daylight Saving Time
UTC -8 hours
Australia and New Zealand:
Page 182
AWST
Western Standard Time (e.g., Perth)
UTC +8 hours
ACST
Central Standard Time (e.g., Darwin)
UTC +9.5 hours
AEST
Eastern Standard/Summer Time (e.g.,
Canberra)
UTC +10 hours
NZT
New Zealand Standard Time
UTC +12 hours
NZDT
New Zealand Daylight Saving Time
UTC +13 hours
7210 SAS D, E OS Basic System Configuration Guide
System Management
Summer Time Conditions
The config>system>time>dst-zone context configures the start and end dates and offset for
summer time or daylight savings time to override system defaults or for user defined time zones.
When configured, the time will be adjusted by adding the configured offset when summer time
starts and subtracting the configured offset when summer time ends.
CLI Syntax: config>system>time
dst-zone zone-name
end {end-week} {end-day} {end-month} [hours-minutes]
offset offset
start {start-week} {start-day} {start-month} [hours-minutes]
Example:
config>system# time
config>system>time# dst-zone pt
config>system>time>dst-zone# start second sunday april 02:00
end first sunday october 02:00
config>system>time>dst-zone# offset 0
If the time zone configured is listed in Table 19, then the starting and ending parameters and offset
do not need to be configured with this command unless there is a need to override the system
defaults. The command will return an error if the start and ending dates and times are not available
either in Table 19 or entered as optional parameters in this command.
The following example displays the configured parameters.
A:ALA-48>config>system>time>dst-zone# info
---------------------------------------------start second sunday april 02:00
end first sunday october 02:00
offset 0
---------------------------------------------A:ALA-48>config>system>time>dst-zone# offset 0
7210 SAS D, E OS Basic System Configuration Guide
Page 183
Common Configuration Tasks
NTP
Network Time Protocol (NTP) is defined in RFC 1305, Network Time Protocol (Version 3)
Specification, Implementation and Analysis. It allows for participating network nodes to keep time
more accurately and maintain time in a synchronized manner between all participating network
nodes.
NTP time elements include:
•
Authentication-check on page 184
•
Authentication-key on page 185
•
Broadcast on page 185
•
Broadcastclient on page 186
•
NTP-Server on page 187
•
Server on page 188
Authentication-check
The authentication-check command provides for the option to skip the rejection of NTP PDUs that
do not match the authentication key or authentication type requirements. The default behavior
when authentication is configured is to reject all NTP protocol PDUs that have a mismatch in
either the authentication key-id, type, or key.
When authentication-check is configured, NTP PDUs are authenticated on receipt. However,
mismatches cause a counter to be increased, one counter for key-id, one for type, and one for key
value mismatches.
CLI Syntax: config>system>time>ntp
authentication-check
Example:
Page 184
config>system>time>ntp#
config>system>time>ntp# authentication-check
config>system>time>ntp# no shutdown
7210 SAS D, E OS Basic System Configuration Guide
System Management
Authentication-key
This command configures an authentication key-id, key type, and key used to authenticate NTP
PDUs sent to and received from other network elements participating in the NTP protocol. For
authentication to work, the authentication key-id, authentication type and authentication key value
must match.
CLI Syntax: config>system>time>ntp
authentication-key key-id {key key} [hash | hash2] type
{des|message-digest}
Example:
config>system>time>ntp#
config>system>time>ntp# authentication-key 1 key A type des
config>system>time>ntp# no shutdown
The following example shows NTP disabled with the authentication-key parameter
enabled.
A:sim1>config>system>time>ntp# info
---------------------------------------------shutdown
authentication-key 1 key "OAwgNUlbzgI" hash2 type des
---------------------------------------------A:sim1>config>system>time>ntp#
Broadcast
The broadcast command is used to transmit broadcast packets on a given subnet.
CLI Syntax: config>system>time>ntp
broadcast [router router-name] {interface
ip-int-name> [key-id key-id]
[ttlttl]
Example:
[version version]
config>system>time>ntp#
config>system>time>ntp# broadcast interface int11 version 4
ttl 127
config>system>time>ntp# no shutdown
The following example in the system>time context shows NTP enabled with the broadcast
command configured.
A:sim1>config>system>time# info detail
---------------------------------------------ntp
no shutdown
authentication-check
ntp-server
broadcast interface int11 version 4 ttl 127
7210 SAS D, E OS Basic System Configuration Guide
Page 185
Common Configuration Tasks
exit
A:sim1>config>system>time#
The following example in the config context shows NTP enabled with the broadcast command
configured. At this level, the NTP broadcast commands are displayed at the end of the output after
the router interfaces are shown.
A:sim1>config info
....
#-------------------------------------------------echo "System Time NTP Configuration"
#-------------------------------------------------system
time
ntp
broadcast interface toboth
exit
exit
exit
A:sim1>config
Broadcastclient
The broadcastclient command enables listening to NTP broadcast messages on the specified
interface.
CLI Syntax: config>system>time>ntp
broadcastclient[router router-name] {interface
ip-int-name} [authenticate]
Example:
config>system>time>ntp#
config>system>time>ntp# broadcastclient interface int11
config>system>time>ntp# no shutdown
The following example shows NTP enabled with the broadcastclient parameter enabled.
A:ALA-12>config>system>time# info
---------------------------------------------ntp
broadcastclient interface int11
no shutdown
exit
dst-zone PT
start second sunday april 02:00
end first sunday october 02:00
offset 0
exit
zone UTC
---------------------------------------------A:ALA-12>config>system>time#
Page 186
7210 SAS D, E OS Basic System Configuration Guide
System Management
NTP-Server
This command configures the node to assume the role of an NTP server. Unless the server
command is used this node will function as an NTP client only and will not distribute the time to
downstream network elements. If an authentication key-id is specified in this command, the NTP
server requires client packets to be authenticated.
CLI Syntax: config>system>time>ntp
ntp-server [transmit key-id]
Example:
config>system>time>ntp#
config>system>time>ntp# ntp-server transmit 1
config>system>time>ntp# no shutdown
The following example shows NTP enabled with the ntp-server command configured.
A:sim1>config>system>time>ntp# info
---------------------------------------------no shutdown
ntp-server
---------------------------------------------A:sim1>config>system>time>ntp#
Peer
Configuration of an NTP peer configures symmetric active mode for the configured peer.
Although any system can be configured to peer with any other NTP node, it is recommended to
configure authentication and to configure known time servers as their peers. Use the no form of
the command to remove the configured peer.
CLI Syntax: config>system>time>ntp
peer ip-address [version version] [key-id key-id]
[prefer]
Example:
config>system>time>ntp#
config>system>time>ntp# peer 192.168.1.1 key-id 1
config>system>time>ntp# no shutdown
The following example shows NTP enabled with the peer command configured.
A:sim1>config>system>time>ntp# info
---------------------------------------------no shutdown
peer 192.168.1.1 key-id 1
---------------------------------------------A:sim1>config>system>time>ntp#
7210 SAS D, E OS Basic System Configuration Guide
Page 187
Common Configuration Tasks
Server
The Server command is used when the node should operate in client mode with the NTP server
specified in the address field. Use the no form of this command to remove the server with the
specified address from the configuration.
Up to five NTP servers can be configured.
CLI Syntax: config>system>time>ntp
server ip-address [key-id key-id] [version version]
[prefer]
Example:
config>system>time>ntp#
config>system>time>ntp# server 192.168.1.1 key-id 1
config>system>time>ntp# no shutdown
The following example shows NTP enabled with the server command configured.
A:sim1>config>system>time>ntp# info
---------------------------------------------no shutdown
server 192.168.1.1 key 1
---------------------------------------------A:sim1>config>system>time>ntp#
Page 188
7210 SAS D, E OS Basic System Configuration Guide
System Management
SNTP
SNTP is a compact, client-only version of the NTP. SNTP can only receive the time from SNTP/
NTP servers; it cannot be used to provide time services to other systems. SNTP can be configured
in either broadcast or unicast client mode.
SNTP time elements include:
•
Broadcast-client on page 189
•
Server-address on page 190
CLI Syntax: config>system
time
sntp
broadcast-client
server-address ip-address [version version-number]
[normal|preferred] [interval seconds]
no shutdown
Broadcast-client
The broadcast-client command enables listening at the global device level to SNTP broadcast
messages on interfaces with broadcast client enabled.
CLI Syntax: config>system>time>sntp
broadcast-client
Example:
config>system>time>sntp#
config>system>time>sntp# broadcast-client
config>system>time>sntp# no shutdown
The following example shows SNTP enabled with the broadcast-client command enabled.
A:ALA-12>config>system>time# info
---------------------------------------------sntp
broadcast-client
no shutdown
exit
dst-zone PT
start second sunday april 02:00
end first sunday october 02:00
offset 0
exit
zone GMT
---------------------------------------------A:ALA-12>config>system>time#
7210 SAS D, E OS Basic System Configuration Guide
Page 189
Common Configuration Tasks
Server-address
The server-address command configures an SNTP server for SNTP unicast client mode.
CLI Syntax: config>system>time>sntp#
config>system>time>sntp# server-address ip-address version versionnumber] [normal|preferred] [interval seconds]
Example:
config>system>time>sntp#
config>system>time# server-address 10.10.0.94 version
1 preferred interval 100
The following example shows SNTP enabled with the server-address command configured.
A:ALA-12>config>system>time# info
---------------------------------------------sntp
server-address 10.10.0.94 version 1 preferred interval 100
no shutdown
exit
dst-zone PT start-date 2006/04/04 12:00 end-date 2006/10/25 12:00
zone GMT
---------------------------------------------A:ALA-12>config>system>time#
Page 190
7210 SAS D, E OS Basic System Configuration Guide
System Management
CRON
The CRON command supports the Service Assurance Agent (SAA) functions as well as the ability
to schedule turning on and off policies to meet “Time of Day” requirements. CRON functionality
includes the ability to specify the commands that need to be run, when they will be scheduled,
including one-time only functionality (oneshot), interval and calendar functions, as well as where
to store the output of the results. In addition, CRON can specify the relationship between input,
output and schedule. Scheduled reboots, peer turn ups, service assurance agent tests and more can
all be scheduled with Cron, as well as OAM events, such as connectivity checks, or
troubleshooting runs.
CRON elements include:
•
Action
•
Schedule
•
Script
•
Time Range
•
Time of Day
Action
Parameters for a script including the maximum amount of time to keep the results from a script
run, the maximum amount of time a script may run, the maximum number of script runs to store
and the location to store the results.
CLI Syntax: config>cron
action action-name [owner action-owner]
expire-time {seconds|forever}
lifetime {seconds|forever}
max-completed unsigned
results file-url
script script-name [owner script-owner]
shutdown
Example:config>cron# action test
config>cron>action# results ftp://172.22.184.249/./sim1/test-results
config>cron>action# no shut
The following example shows a script named “test” receiving an action to store its results in a file
called “test-results”:
A:sim1>config>cron# info
---------------------------------------------script "test"
location "ftp://172.22.184.249/./sim1/test.cfg"
7210 SAS D, E OS Basic System Configuration Guide
Page 191
Common Configuration Tasks
no shutdown
exit
action "test"
results "ftp://172.22.184.249/./sim1/test-results"
no shutdown
exit
---------------------------------------------A:sim1>config>cron# script
Schedule
The schedule function configures the type of schedule to run, including one-time only (oneshot),
periodic or calendar-based runs. All runs are determined by month, day of month or weekday,
hour, minute and interval (seconds). If end-time and interval are both configured, whichever
condition is reached first is applied.
CLI Syntax: config>cron
schedule schedule-name [owner schedule-owner]
action action-name [owner owner-name]
count number
day-of-month {day-number [..day-number]|all}
description description-string
end-time [date|day-name] time
hour {hour-number [..hour-number] | all}
interval seconds
minute {minute-number [..minute-number]|all}
month {month-number [..month-number]|month-name
[..month-name]|all}
no shutdown
type {periodic|calendar|oneshot}
weekday {weekday-number [..weekday-number]|day-name
[..day-name]|all}
shutdown
Example:
config>cron# schedule test2
config>cron>sched# day-of-month 17
config>cron>sched# end-time 2007/07/17 12:00
config>cron>sched# minute 0 15 30 45
config>cron>sched# weekday friday
config>cron>sched# shut
The following example schedules a script named “test2” to run every 15 minutes on the 17th of
each month and every Friday until noon on July 17, 2007:
*A:SR-3>config>cron# info
---------------------------------------------schedule "test2"
shutdown
day-of-month 17
minute 0 15 30 45
weekday friday
Page 192
7210 SAS D, E OS Basic System Configuration Guide
System Management
end-time 2007/07/17 12:00
exit
---------------------------------------------*A:SR-3>config>cron#
Script
The script command opens a new nodal context which contains information on a script.
CLI Syntax: config>cron
script script-name [owner script-owner]
description description-string
location file-url
shutdown
Example:
config>cron# script test
config>cron>script#
The following example names a script “test”:
A:sim1>config>cron# info
---------------------------------------------script "test"
location "ftp://172.22.184.249/./sim1/test.cfg"
no shutdown
exit
---------------------------------------------A:sim1>config>cron#
7210 SAS D, E OS Basic System Configuration Guide
Page 193
Common Configuration Tasks
Time Range
ACLs and QoS policy configurations may be enhanced to support time based matching. CRON
configuration includes time matching with the 'schedule' sub-command. Schedules are based on
events; time-range defines an end-time and will be used as a match criteria.
Time range elements include:
•
Create on page 194
•
Absolute on page 194
•
Daily on page 195
•
Weekdays on page 196
•
Weekend on page 196
•
Weekly on page 197
Create
Use this command to enable the time-range context.
The following example creates a time-range called test1.
CLI Syntax: config>cron>
time-range name create
Example:
config>cron# time-range test1 create
config>cron>time-range$
Absolute
The absolute command configures a start and end time that will not repeat.
CLI Syntax: config>cron>time-range$
absolute absolute-time end absolute-time
Example:
Page 194
config>cron>time-range$ absolute start 2006/05/05,11:00 end
2006/05/06,11:01
config>cron>time-range$
7210 SAS D, E OS Basic System Configuration Guide
System Management
The following example shows an absolute time range beginning on May 5, 2006 at 11:00 and
ending May 6, 2006 at 11:01:
A:sim1>config>cron>time-range# show cron time-range detail
===============================================================================
Cron time-range details
===============================================================================
Name
: test1
Triggers
: 0
Status
: Inactive
Absolute
: start 2006/05/05,11:00 end 2006/05/06,11:01
===============================================================================
A:sim1>config>cron>time-range#
Daily
The daily command configures the start and end of a periodic schedule for every day of the week
(Sunday through Saturday).
CLI Syntax: config>cron>time-range$
daily start time-of-day end time-of-day
Example:
config>cron>time-range$ daily start 11:00 end 12:00
config>cron>time-range$
The following example shows a daily time range beginning at 11:00 and ending at 12:00.
A:sim1>config>cron>time-range# show cron time-range detail
===============================================================================
Cron time-range details
===============================================================================
Name
: 1
Triggers
: 0
Status
: Inactive
Periodic
: daily
Start 11:00 End 12:00
===============================================================================
A:sim1>config>cron>time-range#
7210 SAS D, E OS Basic System Configuration Guide
Page 195
Common Configuration Tasks
Weekdays
The weekdays command configures the start and end of a periodic schedule for weekdays
(Monday through Friday).
CLI Syntax: config>cron>time-range$
weekdays start time-of-day end time-of-day
Example:
config>cron>time-range$ weekdays start 11:00 end 12:00
config>cron>time-range$
The following command shows a time range beginning at 11:00 and ending at 12:00. This
schedule runs all weekdays during this time period.
A:sim1>config>cron>time-range# show cron time-range detail
===============================================================================
Cron time-range details
===============================================================================
Name
: 1
Triggers
: 0
Status
: Inactive
Periodic
: weekdays Start 11:00 End 12:00
===============================================================================
A:sim1>config>cron>time-range#
Weekend
The weekend command configures the start and end of a periodic schedule for weekends
(Saturday and Sunday). The resolution must be at least one minute apart, for example, start at
11:00 and end at 11:01. A start time and end time of 11:00 is invalid.
CLI Syntax: config>cron>time-range$
weekend start time-of-day end time-of-day
Example:
config>cron>time-range$ weekend start 11:00 end 12:00
config>cron>time-range$
The following command shows a weekend time range beginning at 11:00am and ending at
12:00pm, both Saturday and Sunday.
To specify 11:00am to 12:00pm on Saturday or Sunday only, use the Absolute parameter for one
day, or the Weekly parameter for every Saturday or Sunday accordingly. In addition, see the
Schedule parameter to schedule oneshot or periodic events in the config>cron> context.
A:sim1>config>cron>time-range# show cron time-range detail
===============================================================================
Cron time-range details
===============================================================================
Name
: 1
Triggers
: 0
Page 196
7210 SAS D, E OS Basic System Configuration Guide
System Management
Status
Periodic
: Inactive
: weekend Start 11:00 End 12:00
Weekly
The weekly command configures the start and end of a periodic schedule for the same day every
week, for example, every Friday. The start and end dates must be the same. The resolution must be
at least one minute apart, for example, start at 11:00 and end at 11:01. A start time and end time of
11:00 is invalid.
CLI Syntax: config>cron>time-range$
weekly start time-in-week end time-in-week
Example:
config>cron>time-range$ start fri,01:01 end fri,01:02
config>cron>time-range$
The following command shows a weekly time range beginning on Friday at 1:01am ending Friday
at 1:02am.
A:sim1>config>cron>time-range$ info
---------------------------------------------weekly start fri,01:01 end fri,01:02
---------------------------------------------A:sim1>config>cron>time-range$
7210 SAS D, E OS Basic System Configuration Guide
Page 197
Common Configuration Tasks
Time of Day
Time of Day (TOD) suites are useful when configuring many types of time-based policies or when
a large number of subscribers or SAPs require the same type of TOD changes. The TOD suite may
be configured while using specific ingress or egress ACLs or QoS policies, and is an enhancement
of the ingress and egress CLI trees.
Time of day elements include:
•
SAPs on page 198
•
Egress on page 198
•
Ingress on page 200
•
If a TOD Suite is assigned to a SAP, statistics collection are not collected for that SAP.
•
When an item is configured both on SAP level and in the TOD suite assigned to the SAP,
the TOD-suite defined value takes precedence.
•
A policy or filter assignment configured directly on a SAP has a lower priority than any
assignment in a TOD Suite. Hence, it is possible that a new direct configuration has no
immediate effect. If the configuration is made by CLI, a warning is given.
SAPs
Egress
This command is an enhancement for specific egress policies. Use this command to create timerange based associations of previously created filter lists, QoS and scheduler policies. Multiple
policies may be included and each must be assigned a different priority; in case time-ranges
overlap, the priority will be used to determine the prevailing policy. Only a single reference to a
policy may be included without a time-range.
Page 198
7210 SAS D, E OS Basic System Configuration Guide
System Management
Filters
In a TOD suite, filters that have entries with time-ranges may not be selected. Similarly, filter
entries with a time-range may not be created while a TOD suite refers to that filter. QoS policies
and filters referred to by a TOD suite must have scope “template” (default).
The following syntax is used to configure TOD-suite egress parameters.
CLI Syntax: config
cron
tod-suite tod-suite-name create
egress
filter ip ip-filter-id [time-range time-range-name]
[priority priority]
filter mac mac-filter-id[time-range time-rangename] [priority priority]
Example:
config>cron>tod-suite$ egress filter ip 100
config>cron>tod-suite$
The following command shows an egress IP filter association with filter ID 100.
sim1>config>filter# ip-filter 100 create
A:sim1>config>filter>ip-filter$ entry 10 create
A:sim1>config>filter>ip-filter>entry$
A:sim1>config>cron>tod-suite# egress filter ip 100
A:sim1>config>cron>tod-suite# info detail
---------------------------------------------no description
egress
filter ip 100
exit
---------------------------------------------A:sim1>config>cron>tod-suite#
7210 SAS D, E OS Basic System Configuration Guide
Page 199
Common Configuration Tasks
Ingress
This command is an enhancement for specific ingress policies including filter lists and QoS
policies. Use this command to create time-range based associations of previously created filter
lists QoSpolicies. Multiple policies may be included and each must be assigned a different
priority; in case time-ranges overlap, the priority will be used to determine the prevailing policy.
Only a single reference to a policy may be included without a time-range. To configure a daily
time-range across midnight, use a combination of two entries. An entry that starts at hour zero will
take over from an entry that ends at hour 24.
CLI Syntax: config>system
cron
tod-suite tod-suite-name create
ingress
filter ip ip-filter-id [time-range time-range-name]
[priority priority]
filter mac mac-filter-id[time-range time-rangename] [priority priority]
qos policy-id [time-range time-range-name] [priority priority]
Example:
config>cron>tod-suite$ ingress filter ip 100
config>cron>tod-suite$
The following command shows an ingress IP filter association with filter ID 100.
sim1>config>filter# ip-filter 100 create
A:sim1>config>filter>ip-filter$ entry 10 create
A:sim1>config>filter>ip-filter>entry$
...
A:sim1>config>cron>tod-suite# ingress filter ip 100
A:sim1>config>cron>tod-suite# info detail
---------------------------------------------no description
ingress
filter ip 100
exit
---------------------------------------------A:sim1>config>cron>tod-suite#
Page 200
7210 SAS D, E OS Basic System Configuration Guide
System Management
Example:
config>cron>tod-suite$ ingress qos 101
config>cron>tod-suite$
The following command shows an association with ingress QoS-SAP policy 101.
A:sim1>config>qos# sap-egress 101 create
...
A:sim1>config>cron>tod-suite# ingress qos 101
A:sim1>config>cron>tod-suite# info detail
---------------------------------------------no description
ingress
qos 101
exit
---------------------------------------------A:sim1>config>cron>tod-suite#
7210 SAS D, E OS Basic System Configuration Guide
Page 201
Common Configuration Tasks
Configuring Backup Copies
The config-backup command allows you to specify the maximum number of backup versions
of configuration and index files kept in the primary location.
For example, assume the config-backup count is set to 5 and the configuration file is called
xyz.cfg. When a save command is executed, the file xyz.cfg is saved with a .1 extension. Each
subsequent config-backup command increments the numeric extension until the maximum count
is reached. The oldest file (5) is deleted as more recent files are saved.
xyz.cfg
xyz.cfg.1
xyz.cfg.2
xyz.cfg.3
xyz.cfg.4
xyz.cfg.5
xyz.ndx
Each persistent index file is updated at the same time as the associated configuration file. When
the index file is updated, then the save is performed to xyz .cfg and the index file is created as
xyz.ndx. Synchronization between the active and standby is performed for all configurations and
their associated persistent index files.
CLI Syntax: config>system
config-backup count
Example:
config>system#
config>system# config-backup 7
The following example shows the config-backup configuration.
A:ALA-12>config>system>time# info
#-----------------------------------------echo "System Configuration"
#-----------------------------------------name "ALA-12"
contact "Fred Information Technology"
location "Bldg.1-floor 2-Room 201"
clli-code "abcdefg1234"
coordinates "N 45 58 23, W 34 56 12"
config-backup 7
...
---------------------------------------------A:ALA-12>config>system>time#
Page 202
7210 SAS D, E OS Basic System Configuration Guide
System Management
System Administration Parameters
Use the CLI syntax displayed below to configure various system administration parameters.
Administrative parameters include:
•
Validating the Golden Bootstrap Image on page 203
•
Updating the Golden Bootstrap Image on page 204
•
Disconnect on page 204
•
Set-time on page 205
•
Display-config on page 205
•
Save on page 207
•
Reboot on page 208
•
Post-Boot Configuration Extension Files on page 209
Validating the Golden Bootstrap Image
The admin>check-golden-bootstrap command validates the current golden bootstrap image, and
displays its version. A default golden bootstrap image is installed on every 7210 SAS E unit.
CLI Syntax: admin
check-golden-bootstrap
Example:
admin# check-golden-bootstrap
The following example displays the output.
version TiMOS-L-0.0.I312
Golden Bootstrap Image validation successful
7210 SAS D, E OS Basic System Configuration Guide
Page 203
System Administration Parameters
Updating the Golden Bootstrap Image
The admin>update-golden-bootstrap command validates the input file, which must be a 7210
SAS E bootstrap image, and updates the golden bootstrap image with the contents of this file.
CLI Syntax: admin
update-golden-bootstrap [<file-url>]
Example:
admin# update-golden-bootstrap boot.tim
The following is an example of the output.
Updating Golden Bootstrap Image from "boot.tim"
This operation must not be interrupted
Updating Golden Bootstrap image .... Completed.
Disconnect
The disconnect command immediately disconnects a user from a console, Telnet, FTP, or SSH
session.
Note: Configuration modifications are saved to the primary image file.
CLI Syntax: admin
disconnect [address ip-address |username user-name |
{console|telnet|ftp|ssh}]
Example:
admin# disconnect
The following example displays the disconnect command results.
ALA-1>admin# disconnect
ALA-1>admin# Logged out by the administrator
Connection to host lost.
C:\>
Page 204
7210 SAS D, E OS Basic System Configuration Guide
System Management
Set-time
Use the set-time command to set the system date and time. The time entered should be accurate
for the time zone configured for the system. The system will convert the local time to UTC before
saving to the system clock which is always set to UTC. If SNTP or NTP is enabled (no
shutdown) then this command cannot be used. The set-time command does not take into account
any daylight saving offset if defined.
CLI Syntax: admin
set-time date time
Example:
admin# set-time 2007/02/06 04:10:00
The following example displays the set-time command results.
ALA-2# admin set-time 2007/02/06 04:10:00
ALA-2# show time
Thu Feb 2 04:10:04 GMT 2007
ALA-2#
Display-config
The display-config command displays the system’s running configuration.
CLI Syntax: admin
display-config [detail] [index]
Example:
admin# display-config detail
The following example displays a portion of the display-config detail command results.
A:ALA-12>admin# display-config detail
exit all
configure
#-----------------------------------------echo "System Configuration"
#-----------------------------------------system
name "ALA-12"
contact "Fred Information Technology"
location "Bldg.1-floor 2-Room 201"
clli-code "abcdefg1234"
coordinates "N 45 58 23, W 34 56 12"
config-backup 7
boot-good-exec "ftp://test:[email protected]/./1xx.cfg.A"
boot-bad-exec "ftp://test:[email protected]/./1xx.cfg.1"
lacp-system-priority 1
7210 SAS D, E OS Basic System Configuration Guide
Page 205
System Administration Parameters
no synchronize
snmp
shutdown
engineID "0000197f000000000467ff00"
packet-size 1500
general-port 161
exit
login-control
ftp
inbound-max-sessions 3
exit
telnet
inbound-max-sessions 5
outbound-max-sessions 2
exit
idle-timeout 1440
pre-login-message "Property of Service Routing Inc.Unauthorized access prohibited."
motd text “Notice to all users: Software upgrade scheduled 3/2 1:00 AM"
exit
security
management-access-filter
default-action permit
entry 1
no description
...
A:ALA-12>admin#
Page 206
7210 SAS D, E OS Basic System Configuration Guide
System Management
Tech-support
The tech-support command creates a system core dump. NOTE: This command should only
be used with explicit authorization and direction from Alcatel-Lucent’s Technical Assistance
Center (TAC).
Save
The save command saves the running configuration to a configuration file. When the debugsave parameter is specified, debug configurations are saved in the config file. If this parameter is
not specified, debug configurations are not saved between reboots.
CLI Syntax: admin
save [file-url] [detail] [index]
debug-save [file-url]
Example:
admin# save ftp://test:[email protected]/./1.cfg
admin# debug-save debugsave.txt
The following example displays the save command results.
A:ALA-1>admin# save ftp://test:[email protected]/./1x.cfg
Writing file to ftp://test:[email protected]/./1x.cfg
Saving configuration ...Completed.
ALA-1>admin# debug-save ftp://test:[email protected]/./debugsave.txt
Writing file to ftp://julie:[email protected]/./debugsave.txt
Saving debug configuration .....Completed.
A:ALA-1>admin#
7210 SAS D, E OS Basic System Configuration Guide
Page 207
System Administration Parameters
Reboot
The reboot command reboots the router including redundant s in redundant systems. If the now
option is not specified, you are prompted to confirm the reboot operation. The reboot upgrade
command forces an upgrade of the boot ROM and reboot.
CLI Syntax: admin
reboot [upgrade] [now]
Example:
admin# reboot now
The following example displays the reboot command results.
A:ALA-1>admin# reboot now
Are you sure you want to reboot (y/n)? y
Rebooting...
Using preloaded VxWorks boot loader.
...
When an admin reboot auto-init command is issued, the system resets the existing BOF file and
reboots. The system startup process after the admin reboot auto-init command is executed is the
same as the first time system boot as described in System Intialization on page 96.
NOTE: Since the BOF is reset, the system may not boot up withthe last saved system
configuration unless the new BOF file also uses the same configuration file. If it is required that
the system boot up with the last saved system configuration, it is recommended to use the
admin>save file-url command to save the current system configuration and modify the BOF to
use this.
Use the following CLI to reset the BOF and reboot:
CLI Syntax: admin# reboot auto-init [now]
Example: *A:ALA-1# admin reboot auto-init
WARNING: Configuration and/or Boot options may have changed since the last save.
Are you sure you want to reset the bof and reboot (y/n)? Y
Resetting...OK
Alcatel-Lucent 7210 Boot ROM. Copyright 2000-2008 Alcatel-Lucent.
All rights reserved. All use is subject to applicable license agreements.
Page 208
7210 SAS D, E OS Basic System Configuration Guide
System Management
Post-Boot Configuration Extension Files
Two post-boot configuration extension files are supported and are triggered when either a
successful or failed boot configuration file is processed. The commands specify URLs for the CLI
scripts to be run following the completion of the boot-up configuration. A URL must be specified
or no action is taken. The commands are persistent between router (re)boots and are included in
the configuration saves (admin>save).
CLI Syntax: config>system
boot-bad-exec file-url
boot-good-exec file-url
Example:config>system# boot-bad-exec ftp://test:[email protected]/./
fail.cfg
config>system# boot-good-exec ftp://test:[email protected]/./
ok.cfg
The following example displays the command output:
*A:ALA# configure system
*A:ALA>config>system# info
---------------------------------------------#-------------------------------------------------echo "System Configuration"
#-------------------------------------------------name "ALA"
boot-good-exec "cf1:\good.cfg"
boot-bad-exec "cf1:\bad.cfg"
snmp
shutdown
exit
login-control
idle-timeout disable
pre-login-message "ala-1" name
exit
time
ntp
authentication-key 1 key "SV3BxZCsIvI" hash type message-digest
server 10.135.16.130
peer 21.0.0.1 key-id 1
no shutdown
exit
sntp
server-address 10.135.16.90 preferred
no shutdown
exit
zone UTC
exit
thresholds
rmon
exit
exit
7210 SAS D, E OS Basic System Configuration Guide
Page 209
System Administration Parameters
#-------------------------------------------------echo "System Security Configuration"
#-------------------------------------------------security
hash-control read-version all write-version 1
telnet-server
ftp-server
snmp
community "private" rwa version both
community "public" r version both
exit
source-address
application ftp 10.135.16.97
application snmptrap 10.135.16.97
application ping 10.135.16.97
application dns 10.135.16.97
exit
exit
---------------------------------------------*A:ALA>config>system#
Page 210
7210 SAS D, E OS Basic System Configuration Guide
System Management
Show Command Output and Console Messages
The show>system>information command displays the current value of the bad/good exec
URLs and indicates whether a post-boot configuration extension file was executed when the
system was booted. If an extension file was executed, the show>system>information
command also indicates if it completed successfully or not.
When executing a post-boot configuration extension file, status messages are output to the
CONSOLE screen prior to the “Login” prompt.
Following is an example of a failed boot-up configuration that caused a boot-bad-exec file
containing another error to be executed:
Attempting to exec configuration file:
’ftp://test:[email protected]/./12.cfg’ ...
System Configuration
Log Configuration
MAJOR: CLI #1009 An error occurred while processing a CLI command File ftp://test:[email protected]/./12.cfg, Line 195: Command "log" failed.
CRITICAL: CLI #1002 An error occurred while processing the configuration file.
The system configuration is missing or incomplete.
MAJOR: CLI #1008 The SNMP daemon is disabled.
If desired, enable SNMP with the ’config>system>snmp no shutdown’ command.
Attempting to exec configuration failure extension file:
’ftp://test:[email protected]/./fail.cfg’ ...
Config fail extension
Enabling SNMP daemon
MAJOR: CLI #1009 An error occurred while processing a CLI command File ftp://test:[email protected]/./fail.cfg, Line 5: Command "abc log" failed.
TiMOS-B-x.0.Rx both/hops ALCATEL Copyright (c) 2000-2009 Alcatel-Lucent.
All rights reserved. All use subject to applicable license agreements.
Built on Thu Nov 207 19:19:11 PST 2008 by builder in /rel5x.0/b1/Rx/panos/main
Login:
7210 SAS D, E OS Basic System Configuration Guide
Page 211
Configuring System Monitoring Thresholds
Configuring System Monitoring Thresholds
Creating Events
The event command controls the generation and notification of threshold crossing events
configured with the alarm command. When a threshold crossing event is triggered, the rmon
event configuration optionally specifies whether an entry in the RMON-MIB log table be created
to record the occurrence of the event. It can also specify whether an SNMP notification (trap) be
generated for the event. There are two notifications for threshold crossing events, a rising alarm
and a falling alarm.ping-address
Creating an event entry in the RMON-MIB log table does not create a corresponding entry in the
event logs. However, when the event is set to trap the generation of a rising alarm or falling alarm
notification creates an entry in the event logs and that is distributed to whatever log destinations
are configured: console, session, memory, file, syslog, or SNMP trap destination. The logger
message includes a rising or falling threshold crossing event indicator, the sample type (absolute
or delta), the sampled value, the threshold value, the rmon-alarm-id, the associated rmon-event-id
and the sampled SNMP object identifier.
The alarm command configures an entry in the RMON-MIB alarm table. The alarm command
controls the monitoring and triggering of threshold crossing events. In order for notification or
logging of a threshold crossing event to occur there must be at least one associated rmon event
configured.
The agent periodically takes statistical sample values from the MIB variable specified for
monitoring and compares them to thresholds that have been configured with the alarm command.
The alarm command configures the MIB variable to be monitored, the polling period (interval),
sampling type (absolute or delta value), and rising and falling threshold parameters. If a sample
has crossed a threshold value, the associated ‘event’ is generated.
Preconfigured CLI threshold commands are available. Preconfigured commands hide some of the
complexities of configuring RMON alarm and event commands and perform the same function. In
particular, the preconfigured commands do not require the user to know the SNMP object
identifier to be sampled. The preconfigured threshold configurations include memory warnings
and alarms and compact flash usage warnings and alarms.
Page 212
7210 SAS D, E OS Basic System Configuration Guide
System Management
To create events, use the following CLI:
Example:
config>system>thresholds# cflash-cap-warn cf1-B: risingthreshold 2000000 falling-threshold 1999900 interval 240 trap startupalarm either
Example: config>system>thresholds# memory-use-alarm rising-threshold
50000000 falling-threshold 45999999 interval 500 both startup-alarm
either
Example:
config>system>thresh# rmon
Example: config>system>thresh>rmon# event 5 both description "alarm
testing" owner "Timos CLI"
The following example displays the command output:
A:ALA-49>config>system>thresholds# info
---------------------------------------------rmon
event 5 description "alarm testing" owner "Timos CLI"
exit
cflash-cap-warn cf1-B: rising-threshold 2000000 falling-threshold 1999900
interval 240 trap
memory-use-alarm rising-threshold 50000000 falling-threshold 45999999 interval
500
---------------------------------------------A:ALA-49>config>system>thresholds#
7210 SAS D, E OS Basic System Configuration Guide
Page 213
Configuring System Monitoring Thresholds
System Alarm Contact Inputs in 7210 SAS-E devices
The 7210 SAS E platform hardware supports alarm contact inputs that allow an operator to
monitor and report changes in the external environmental conditions. In a remote or outdoor
deployment, alarm contact inputs allow an operator to detect conditions, for example, air
conditioner fault, open door.
An operator can configure generation of events when alarm contact inputs transition between the
open and close states. For each generated event, the operator can specify the:
Page 214
•
Action associated with each state transition.
•
Severity associated with each state transition.
•
Log message associated with each state transition.
7210 SAS D, E OS Basic System Configuration Guide
System Management
Configuring LLDP
The following output displays LLDP defaults:
A:7210-SAS>config>system>lldp# info detail
---------------------------------------------no tx-interval
no tx-hold-multiplier
no reinit-delay
no notification-interval
no tx-credit-max
no message-fast-tx
no message-fast-tx-init
no shutdown
----------------------------------------------
The following example displays an LLDP port configuration:
*A:7210-SAS>config>port>ethernet>lldp# info
---------------------------------------------dest-mac nearest-bridge
admin-status tx-rx
tx-tlvs port-desc sys-cap
tx-mgmt-address system
exit
---------------------------------------------*A:7210-SAS>config>port>ethernet>lldp#
The following example displays a global system LLDP configuration:
A:7210-SAS>config>system>lldp# info
---------------------------------------------tx-interval 10
tx-hold-multiplier 2
reinit-delay 5
notification-interval 10
---------------------------------------------A:7210-SAS>config>system>lldp#
7210 SAS D, E OS Basic System Configuration Guide
Page 215
Configuring LLDP
Page 216
7210 SAS D, E OS Basic System Configuration Guide
System Management
System Command Reference
Command Hierarchies
Configuration Commands
• System Information Commands on page 217
• System Alarm Commands on page 218
• System Time Commands on page 219
• Cron Commands on page 220
• System Administration (Admin) Commands on page 221
• System Alarm Contact Commands on page 222
• Show Commands on page 223
• Debug Commands on page 224
• Clear Commands on page 224
System Information Commands
config
— system
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
alarm-contact-input alarm-contact-input-id (supported only on 7210 SAS E)
boot-bad-exec file-url
no boot-bad-exec
boot-bad-exec file-url
no boot-bad-exec
clli-code clli-code
no clli-code
config-backup count
no config-backup
contact contact-name
no contact
coordinates coordinates
no coordinates
lacp-system-priority lacp-system-priority
no lacp-system-priority
lldp
location location
no location
login-control
name system-name
no name
7210 SAS D, E OS Basic System Configuration Guide
Page 217
Command Hierarchies
System Alarm Commands
config
— system
— thresholds
— cflash-cap-alarm cflash-id rising-threshold threshold [falling-threshold threshold]
interval seconds [rmon-event-type] [startup-alarm alarm-type]
— no cflash-cap-alarm cflash-id
— cflash-cap-warn cflash-id rising-threshold threshold [falling-threshold threshold]
interval seconds [rmon-event-type] [startup-alarm alarm-type]
— no cflash-cap-warn cflash-id
— memory-use-alarm rising-threshold threshold [falling-threshold threshold] interval
seconds [rmon-event-type] [startup-alarm alarm-type]
— no memory-use-alarm
— memory-use-warn rising-threshold threshold [falling-threshold threshold] interval
seconds [rmon-event-type] [startup-alarm alarm-type]
— no memory-use-warn
— [no] rmon
— alarm rmon-alarm-id variable-oid oid-string interval seconds [sample-type]
[startup-alarm alarm-type] [rising-event rmon-event-id rising-threshold
threshold] [falling event rmon-event-id falling-threshold threshold] [owner
owner-string]
— no alarm rmon-alarm-id
— event rmon-event-id [event-type] [description description-string] [owner
owner-string]
— no event rmon-event-id
Page 218
7210 SAS D, E OS Basic System Configuration Guide
System Management
System Time Commands
root
— admin
— set-time [date] [time]
config
— system
— time
— [no] ntp
— [no] authentication-check
— authentication-key key-id key key [hash | hash2] type {des | message-digest}
— no authentication-key key-id
— [no] broadcast [router router-name] {interface ip-int-name} [key-id key-id]
[version version] [ttl ttl]
— [no] broadcast [router router-name] {interface ip-int-name}
— broadcastclient [router router-name] {interface ip-int-name} [authenticate]
— [no] broadcastclient [router router-name] {interface ip-int-name}
— [no] ntp-server [transmit key-id]
— [no] peer ip-address [version version] [key-id key-id] [prefer]
— [no] server ip-address [version version] [key-id key-id] [prefer]
— [no] shutdown
— [no] sntp
— [no] broadcast-client
— server-address ip-address [version version-number] [normal | preferred]
[interval seconds]
— no server-address ip-address
— [no] shutdown
— [no] dst-zone [std-zone-name | non-std-zone-name]
— end {end-week} {end-day} {end-month} [hours-minutes]
— offset offset
— start {start-week} {start-day} {start-month} [hours-minutes]
— zone std-zone-name | non-std-zone-name [hh [:mm]]
— no zone
7210 SAS D, E OS Basic System Configuration Guide
Page 219
Command Hierarchies
Cron Commands
config
— [no] cron
— [no] action action-name [owner owner-name]
— expire-time {seconds | forever}
— lifetime {seconds | forever}
— max-completed unsigned
— [no] results file-url
— [no] script script-name [owner owner-name]
— [no]shutdown
— [no] schedule schedule-name [owner owner-name]
— [no] action action-name [owner owner-name]
— [no] day-of-month {day-number [..day-number] all}
— count number
— [no] description description-string
— [no] end-time [date|day-name] time
— [no] hour {..hour-number [..hour-number]|all}
— [no] interval seconds
— [no] minute {minute-number [..minute-number]|all}
— [no] month {month-number [..month-number]|month-name [..month-name]|all}
— [no] shutdown
— type {schedule-type}
— [no] weekday {weekday-number [..weekday-number]|day-name [..day-name]|all}
— [no] script [no] script script-name [owner owner-name]
— [no] description description-string
— [no] location file-url
— [no] shutdown
— [no] time-range name [create]
— absolute start start-absolute-time end end-absolute-time
— no absolute start start-absolute-time
— daily start start-time-of-day end end-time-of-day
— no daily start start-time-of-day
— weekdays start start-time-of-day end end-time-of-day
— no weekdays start start-time-of-day
— weekend start start-time-of-day end end-time-of-day
— no weekend start start-time-of-day
— weekly start start-time-in-week end end-time-in-week
— no weekly start start-time-in-week
— [no] tod-suite <tod-suite-name> [create]
— egress
— filter ip ip-filter-id [time-range time-range-name] [priority priority]
— filter mac mac-filter-id [time-range time-range-name] [priority priority]
— no filter ip ip-filter-id [time-range time-range-name]
— no filter mac mac-filter-id [time-range time-range-name
— ingress
— filter ip ip-filter-id [time-range time-range-name] [priority priority]
— filter mac mac-filter-id [time-range time-range-name] [priority priority]
— no filter ip ip-filter-id [time-range time-range-name]
— no filter mac mac-filter-id [time-range time-range-name
— qos policy-id [time-range time-range-name] [priority priority]
— no qos policy-id [time-range time-range-name]
Page 220
7210 SAS D, E OS Basic System Configuration Guide
System Management
System Administration (Admin) Commands
root
— admin
—
—
—
—
—
—
—
—
—
—
check-golden-bootstrap
debug-save file-url
disconnect {address ip-address | username user-name | console | telnet | ftp | ssh}
display-config [detail | index]
[no] enable-tech
reboot [upgrade] [auto-init] [now]
save [file-url] [detail] [index]
set-time <date> <time>
tech-support [file-url]
update-golden-bootstrap [file-url]
7210 SAS D, E OS Basic System Configuration Guide
Page 221
Command Hierarchies
System Alarm Contact Commands
Note: System alarm contact commands are not supported on 7210 SAS-D devices.
config
— system
— alarm-contact-input alarm-contact-input-id
— [no] alarm-output-severity [critical | major | minor | none]
— [no] clear-alarm-msg {alarm-msg-txt}
— description description-string
— normal-state [open | closed]
— [no] shutdown
— [no] trigger-alarm-msg {alarm-msg-txt}
LLDP System Commands
configure
— system
— lldp
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
message-fast-tx time
no message-fast-tx
message-fast-tx-init count
no message-fast-tx-init
notification-interval time
no notification-interval
reinit-delay time
no reinit-delay
[no] shutdown
tx-credit-max count
no tx-credit-max
tx-hold-multiplier multiplier
no tx-hold-multiplier
tx-interval interval
no tx-interval
LLDP Ethernet Port Commands
configure
— port port-id
— ethernet
— lldp
— dest-mac {nearest-bridge | nearest-non-tpmr | nearest-customer}
— admin-status {rx | tx | tx-rx | disabled}
— [no] notification
— tx-mgmt-address [system]
— no tx-mgmt-address
— tx-tlvs [port-desc] [sys-name] [sys-desc] [sys-cap]
— no tx-tlvs
Page 222
7210 SAS D, E OS Basic System Configuration Guide
System Management
Show Commands
show
—
—
—
—
—
—
—
—
—
alarm-contact-input alarm-contact-input-id detail (supported only on 7210 SAS-E)
alarm-contact-input all (supported only on 7210 SAS-E)
chassis [environment] [power-supply] ('environment' option supported only on 7210 SAS E)
cron
— action action-name [owner owner-name]
— action run-history [run-state]
— schedule action-name [owner owner-name]
— script script-name [owner owner-name]
— tod-suite tod-suite-name [detail] associations failed-associations
— time-range name associations [detail]
time
system
— connections [address ip-address [port port-number] [detail]
— cpu [sample-period seconds]
— information
— lldp
— memory-pools
— ntp
— sntp
— thresholds
— time
uptime
alarm-contact-input alarm-contact-input-id [detail] (Supported only on 7210 SAS-E)
alarm-contact-input all (Supported only on 7210 SAS-E)
7210 SAS D, E OS Basic System Configuration Guide
Page 223
Command Hierarchies
Clear Commands
clear
— screen
Debug Commands
debug
— [no] system
— ntp [router router-name] [interface ip-int-name]
Page 224
7210 SAS D, E OS Basic System Configuration Guide
System Management
System Command Reference
Generic Commands
shutdown
Syntax
Context
Description
[no] shutdown
config>system>time>ntp
config>system>time>sntp
config>cron>action
config>cron>sched
config>cron>script
config>system>lldp
This command administratively disables the entity. When disabled, an entity does not change, reset,
or remove any configuration settings or statistics.
The operational state of the entity is disabled as well as the operational state of any entities contained
within. Many objects must be shut down before they may be deleted.
The no form of this command places the entity into an administratively enabled state.
Default
no shutdown
description
Syntax
Context
Description
description description-string
no description
config>cron>sched
This command creates a text description stored in the configuration file for a configuration context.
The description command associates a text string with a configuration context to help identify the
content in the configuration file.
The no form of this command removes the string from the configuration.
Default
Parameters
No description associated with the configuration context.
string — The description character string. Allowed values are any string up to 80 characters long
composed of printable, 7-bit ASCII characters. If the string contains special characters (#, $,
spaces, etc.), the entire string must be enclosed within double quotes.
7210 SAS D, E OS Basic System Configuration Guide
Page 225
System Information Commands
System Information Commands
boot-bad-exec
Syntax
Context
Description
boot-bad-exec file-url
no boot-bad-exec
config>system
Use this command to configure a URL for a CLI script to exec following a failure of a boot-up
configuration. The command specifies a URL for the CLI scripts to be run following the completion
of the boot-up configuration. A URL must be specified or no action is taken.
The commands are persistent between router (re)boots and are included in the configuration saves
(admin>save).
Default
Parameters
no boot-bad-exec
file-url — Specifies the location and name of the CLI script file executed following failure of the
boot-up configuration file execution. When this parameter is not specified, no CLI script file is
executed.
Values
file url:
local-url:
remote-url:
cflash-id:
Related
Commands
local-url | remote-url: 255 chars max
[cflash-id/][file-path]
[{ftp://} login:pswd@remote-locn/][file-path]
remote-locn [ hostname | ipv4-address]
ipv4-address
a.b.c.d
cf1:
exec command on page 49 — This command executes the contents of a text file as if they were CLI
commands entered at the console.
boot-good-exec
Syntax
Context
Description
Default
Parameters
Page 226
boot-good-exec file-url
no boot-good-exec
config>system
Use this command to configure a URL for a CLI script to exec following the success of a boot-up
configuration.
no boot-good-exec
file-url — Specifies the location and name of the file executed following successful completion of the
boot-up configuration file execution. When this parameter is not specified, no CLI script file is
executed.
7210 SAS D, E OS Basic System Configuration Guide
System Management
Values
file url:
local-url:
remote-url:
cflash-id:
Related
Commands
local-url | remote-url: 255 chars max
[cflash-id/][file-path]
[{ftp://} login:pswd@remote-locn/][file-path]
remote-locn [ hostname | ipv4-address]
ipv4-address
a.b.c.d
cf1:
exec command on page 49 — This command executes the contents of a text file as if they were CLI
commands entered at the console.
clli-code
Syntax
Context
Description
clli-code clli-code
no clli-code
config>system
This command creates a Common Language Location Identifier (CLLI) code string for the router. A
CLLI code is an 11-character standardized geographic identifier that uniquely identifies geographic
locations and certain functional categories of equipment unique to the telecommunications industry.
No CLLI validity checks other than truncating or padding the string to eleven characters are
performed.
Only one CLLI code can be configured, if multiple CLLI codes are configured the last one entered
overwrites the previous entry.
The no form of the command removes the CLLI code.
Default
Parameters
none — No CLLI codes are configured.
clli-code — The 11 character string CLLI code. Any printable, seven bit ASCII characters can be
used within the string. If the string contains special characters (#, $, spaces, etc.), the entire string
must be enclosed within double quotes. If more than 11 characters are entered, the string is
truncated. If less than 11 characters are entered the string is padded with spaces.
config-backup
Syntax
Context
Description
config-backup count
no config-backup
config>system
This command configures the maximum number of backup versions maintained for configuration
files and BOF.
For example, assume the config-backup count is set to 5 and the configuration file is called xyz.cfg.
When a save command is executed, the file xyz.cfg is saved with a .1 extension. Each subsequent
config-backup command increments the numeric extension until the maximum count is reached.
7210 SAS D, E OS Basic System Configuration Guide
Page 227
System Information Commands
xyz.cfg
xyz.cfg.1
xyz.cfg.2
xyz.cfg.3
xyz.cfg.4
xyz.cfg.5
xyz.ndx
Each persistent index file is updated at the same time as the associated configuration file. When the
index file is updated, then the save is performed to xyz.cfg and the index file is created as xyz.ndx.
Synchronization between the active and standby is performed for all configurations and their
associated persistent index files.
The no form of the command returns the configuration to the default value.
Default
Parameters
5
count — The maximum number of backup revisions.
Values
1—9
contact
Syntax
Context
Description
contact contact-name
no contact
config>system
This command creates a text string that identifies the contact name for the device.
Only one contact can be configured, if multiple contacts are configured the last one entered will
overwrite the previous entry.
The no form of the command reverts to default.
Default
Parameters
none — No contact name is configured.
contact-name — The contact name character string. The string can be up to 80 characters long. Any
printable, seven-bit ASCII characters can be used within the string. If the string contains special
characters (#, $, spaces, etc.), the entire string must be enclosed within double quotes.
coordinates
Syntax
Context
Description
Page 228
coordinates coordinates
no coordinates
config>system
This command creates a text string that identifies the system coordinates for the device location. For
example, the command coordinates “37.390 -122.0550" is read as latitude 37.390 north and
longitude 122.0550 west.
7210 SAS D, E OS Basic System Configuration Guide
System Management
Only one set of coordinates can be configured. If multiple coordinates are configured, the last one
entered overwrites the previous entry.
The no form of the command reverts to the default value.
Default
Parameters
none — No coordinates are configured.
coordinates — The coordinates describing the device location character string. The string may be up
to 80 characters long. Any printable, seven-bit ASCII characters can be used within the string. If
the string contains special characters (#, $, spaces, etc.), the entire string must be enclosed within
double quotes. If the coordinates are subsequently used by an algorithm that locates the exact
position of this node then the string must match the requirements of the algorithm.
lacp-system-priority
Syntax
Context
Description
Default
Parameters
lacp-system-priority lacp-system-priority
no lacp-system-priority
config>system
This command configures the Link Aggregation Control Protocol (LACP) system priority on
aggregated Ethernet interfaces. LACP allows the operator to aggregate multiple physical interfaces to
form one logical interface.
32768
lacp-system-priority — Specifies the LACP system priority.
Values
1 — 65535
location
Syntax
Context
Description
location location
no location
config>system
This command creates a text string that identifies the system location for the device.
Only one location can be configured. If multiple locations are configured, the last one entered
overwrites the previous entry.
The no form of the command reverts to the default value.
Default
none — No system location is configured.
7210 SAS D, E OS Basic System Configuration Guide
Page 229
System Information Commands
Parameters
location — Enter the location as a character string. The string may be up to 80 characters long. Any
printable, seven-bit ASCII characters can be used within the string. If the string contains special
characters (#, $, spaces, etc.), the entire string must be enclosed within double quotes.
login-control
Syntax
Context
Description
login-control
config>system
This command enables the context to configure login control.
name
Syntax
Context
Description
name system-name
no name
config>system
This command creates a system name string for the device.
For example, system-name parameter ALA-1 for the name command configures the device name as
ALA-1.
ABC>config>system# name "ALA-1"
ALA-1>config>system#
Only one system name can be configured. If multiple system names are configured, the last one
encountered overwrites the previous entry.
The no form of the command reverts to the default value.
Default
Parameters
Page 230
The default system name is set to the chassis serial number which is read from the backplane
EEPROM.
system-name — Enter the system name as a character string. The string may be up to 32 characters
long. Any printable, seven-bit ASCII characters can be used within the string. If the string
contains special characters (#, $, spaces, etc.), the entire string must be enclosed within double
quotes.
7210 SAS D, E OS Basic System Configuration Guide
System Management
System Alarm Commands
alarm
Syntax
Context
Description
alarm rmon-alarm-id variable-oid oid-string interval seconds [sample-type] [startup-alarm
alarm-type] [rising-event rmon-event-id rising-threshold threshold] [falling-event rmonevent-id falling threshold threshold] [owner owner-string]
no alarm rmon-alarm-id
config>system>thresholds>rmon
The alarm command configures an entry in the RMON-MIB alarmTable. The alarm command
controls the monitoring and triggering of threshold crossing events. In order for notification or
logging of a threshold crossing event to occur there must be at least one associated rmon>event
configured.
The agent periodically takes statistical sample values from the MIB variable specified for monitoring
and compares them to thresholds that have been configured with the alarm command. The alarm
command configures the MIB variable to be monitored, the polling period (interval), sampling type
(absolute or delta value), and rising and falling threshold parameters. If a sample has crossed a
threshold value, the associated event is generated.
Use the no form of this command to remove an rmon-alarm-id from the configuration.
Parameters
rmon-alarm-id — The rmon-alarm-id is a numerical identifier for the alarm being configured. The
number of alarms that can be created is limited to 1200.
Default
None
Values
1 — 65535
variable-oid oid-string — The oid-string is the SNMP object identifier of the particular variable to
be sampled. Only SNMP variables that resolve to an ASN.1 primitive type of integer (integer,
Integer32, Counter32, Counter64, Gauge, or TimeTicks) may be sampled. The oid-string may be
expressed using either the dotted string notation or as object name plus dotted instance identifier.
For example, "1.3.6.1.2.1.2.2.1.10.184582144" or "ifInOctets.184582144".
The oid-string has a maximum length of 255 characters
Default
None
interval seconds — The interval in seconds specifies the polling period over which the data is
sampled and compared with the rising and falling thresholds. When setting this interval value,
care should be taken in the case of ’delta’ type sampling - the interval should be set short enough
that the sampled variable is very unlikely to increase or decrease by more than 2147483647 - 1
during a single sampling interval. Care should also be taken not to set the interval value too low
to avoid creating unnecessary processing overhead.
Default
None
Values
1 — 2147483647
7210 SAS D, E OS Basic System Configuration Guide
Page 231
System Alarm Commands
sample-type — Specifies the method of sampling the selected variable and calculating the value to
be compared against the thresholds.
Default
Absolute
Values
absolute — Specifies that the value of the selected variable will be compared
directly with the thresholds at the end of the sampling interval.
delta — Specifies that the value of the selected variable at the last sample will be
subtracted from the current value, and the difference compared with the thresholds.
startup-alarm alarm-type — Specifies the alarm that may be sent when this alarm is first created.
If the first sample is greater than or equal to the rising threshold value and ’startup-alarm’ is
equal to ’rising’ or ’either’, then a single rising threshold crossing event is generated.
If the first sample is less than or equal to the falling threshold value and ’startup-alarm’ is equal
to ’falling’ or ’either’, a single falling threshold crossing event is generated.
Default
either
Values
rising, falling, either
rising-event rmon-event-id — The identifier of the the rmon>event that specifies the action to be
taken when a rising threshold crossing event occurs.
If there is no corresponding ’event’ configured for the specified rmon-event-id, then no
association exists and no action is taken.
If the ’rising-event rmon-event-id’ has a value of zero (0), no associated event exists.
If a ’rising event rmon-event’ is configured, the CLI requires a ’rising-threshold’ to also be
configured.
Default
0
Values
0 — 65535
rising-threshold threshold — Specifies a threshold for the sampled statistic. When the current
sampled value is greater than or equal to this threshold, and the value at the last sampling interval
was less than this threshold, a single threshold crossing event will be generated. A single
threshold crossing event will also be generated if the first sample taken is greater than or equal to
this threshold and the associated startup-alarm is equal to rising or either.
After a rising threshold crossing event is generated, another such event will not be generated
until the sampled value falls below this threshold and reaches less than or equal the ’fallingthreshold’ value.
Default
0
Values
-2147483648 — 2147483647
falling-event rmon-event-id — The identifier of the rmon>event that specifies the action to be taken
when a falling threshold crossing event occurs. If there is no corresponding event configured for
the specified rmon-event-id, then no association exists and no action is taken. If the falling-event
has a value of zero (0), no associated event exists.
If a ’falling event’ is configured, the CLI requires a ’falling-threshold to also be configured.
Page 232
Default
0
Values
-2147483648 — 2147483647
7210 SAS D, E OS Basic System Configuration Guide
System Management
falling-threshold threshold — Specifies a threshold for the sampled statistic. When the current
sampled value is less than or equal to this threshold, and the value at the last sampling interval
was greater than this threshold, a single threshold crossing event will be generated. A single
threshold crossing event will also be generated if the first sample taken is less than or equal to
this threshold and the associated ’startup-alarm’ is equal to ’falling’ or ’either’.
After a rising threshold crossing event is generated, another such event will not be generated
until the sampled value rises above this threshold and reaches greater than or equal the risingthreshold threshold value.
Default
0
Values
-2147483648 — 2147483647
owner owner — The owner identifies the creator of this alarm. It defaults to "TiMOS CLI". This
parameter is defined primarily to allow entries that have been created in the RMON-MIB
alarmTable by remote SNMP managers to be saved and reloaded in a CLI configuration file. The
owner will not normally be configured by CLI users and can be a maximum of 80 characters
long.
Default
TiMOS CLI
Configuration example:
alarm 3 variable-oid ifInOctets.184582144 interval 20 sample-type delta start-alarm
either rising-event 5 rising-threshold 10000 falling-event 5 falling-threshold 9000
owner "TiMOS CLI"
cflash-cap-alarm
Syntax
Context
Description
cflash-cap-alarm cflash-id rising-threshold threshold [falling-threshold threshold]
interval seconds [rmon-event-type] [startup-alarm alarm-type]
no cflash-cap-alarm cflash-id
config>system>thresholds
This command enables capacity monitoring of the compact flash specified in this command. The
severity level is alarm. Both a rising and falling threshold can be specified.
The no form of this command removes the configured compact flash threshold alarm.
Parameters
cflash-id — The cflash-id specifies the name of the cflash device to be monitored.
Values
cf1:, cf1-A:
rising-threshold threshold — Specifies a threshold for the sampled statistic. When the current
sampled value is greater than or equal to this threshold, and the value at the last sampling interval
was less than this threshold, a single threshold crossing event will be generated. A single
threshold crossing event will also be generated if the first sample taken is greater than or equal to
this threshold and the associated ’startup-alarm’ is equal to ’rising’ or ’either’.
7210 SAS D, E OS Basic System Configuration Guide
Page 233
System Alarm Commands
After a rising threshold crossing event is generated, another such event will not be generated
until the sampled value falls below this threshold and reaches less than or equal the ’fallingthreshold’ value.
Default
0
Values
-2147483648 — 2147483647
falling-threshold threshold — Specifies a threshold for the sampled statistic. When the current
sampled value is less than or equal to this threshold, and the value at the last sampling interval
was greater than this threshold, a single threshold crossing event will be generated. A single
threshold crossing event will also be generated if the first sample taken is less than or equal to
this threshold and the associated startup-alarm is equal to falling or either.
After a rising threshold crossing event is generated, another such event will not be generated
until the sampled value raises above this threshold and reaches greater than or equal the risingthreshold value.
Default
0
Values
-2147483648 — 2147483647
interval seconds — Specifies the polling period, in seconds, over which the data is sampled and
compared with the rising and falling thresholds.
Values
1 — 2147483647
rmon-event-type — Specifies the type of notification action to be taken when this event occurs.
Values
log — An entry is made in the RMON-MIB log table for each event occurrence.
This does not create a TiMOS logger entry. The RMON-MIB log table entries can
be viewed using the show>system>thresholds CLI command.
trap — A TiMOS logger event is generated. The TiMOS logger utility then
distributes the notification of this event to its configured log destinations which
may be CONSOLE, telnet session , memory log, cflash file, syslog, or SNMP trap
destinations logs.
both — Both a entry in the RMON-MIB logTable and a TiMOS logger event are
generated.
none — No action is taken.
Default
both
startup-alarm alarm-type — Specifies the alarm that may be sent when this alarm is first created.
If the first sample is greater than or equal to the rising threshold value and startup-alarm is equal
to rising or either, then a single rising threshold crossing event is generated.
If the first sample is less than or equal to the falling threshold value and startup-alarm is equal to
falling or either, a single falling threshold crossing event is generated.
Default
either
Values
rising, falling, either
Configuration example:
Page 234
7210 SAS D, E OS Basic System Configuration Guide
System Management
cflash-cap-alarm cf1-A: rising-threshold 50000000 falling-threshold 49999900 interval 120
rmon-event-type both start-alarm rising.
cflash-cap-warn
Syntax
Context
cflash-cap-warn cflash-id rising-threshold threshold [falling-threshold threshold]
interval seconds [rmon-event-type] [startup-alarm alarm-type]
no cflash-cap-warn cflash-id
config>system>thresholds
Description
This command enables capacity monitoring of the compact flash specified in this command. The
severity level is warning. Both a rising and falling threshold can be specified. The no form of this
command removes the configured compact flash threshold warning.
Parameters
cflash-id — The cflash-id specifies the name of the cflash device to be monitored.
Values
cf1:, cf1-A:
rising-threshold threshold — Specifies a threshold for the sampled statistic. When the current
sampled value is greater than or equal to this threshold, and the value at the last sampling interval
was less than this threshold, a single threshold crossing event will be generated. A single
threshold crossing event will also be generated if the first sample taken is greater than or equal to
this threshold and the associated startup-alarm is equal to rising or either.
After a rising threshold crossing event is generated, another such event will not be generated
until the sampled value falls below this threshold and reaches less than or equal the fallingthreshold value.
Default
0
Values
-2147483648 — 2147483647
falling-threshold threshold — Specifies a threshold for the sampled statistic. When the current
sampled value is less than or equal to this threshold, and the value at the last sampling interval
was greater than this threshold, a single threshold crossing event will be generated. A single
threshold crossing event will also be generated if the first sample taken is less than or equal to
this threshold and the associated startup-alarm is equal to falling or either.
After a rising threshold crossing event is generated, another such event will not be generated
until the sampled value raises above this threshold and reaches greater than or equal the risingthreshold value.
Default
0
Values
-2147483648 — 2147483647
interval seconds — Specifies the polling period over which the data is sampled and compared with
the rising and falling thresholds.
Values
1 — 2147483647
rmon-event-type — Specifies the type of notification action to be taken when this event occurs.
7210 SAS D, E OS Basic System Configuration Guide
Page 235
System Alarm Commands
Values
log — In the case of log, an entry is made in the RMON-MIB log table for each
event occurrence. This does not create a TiMOS logger entry. The RMON-MIB log
table entries can be viewed using the show>system>thresholds CLI command.
trap — In the case of trap, a TiMOS logger event is generated. The TiMOS logger
utility then distributes the notification of this event to its configured log
destinations which may be CONSOLE, telnet session , memory log, cflash file,
syslog, or SNMP trap destinations logs.
both — In the case of both, both a entry in the RMON-MIB logTable and a TiMOS
logger event are generated.
none — In the case of none, no action is taken.
Default
both
startup-alarm alarm-type — Specifies the alarm that may be sent when this alarm is first created. If
the first sample is greater than or equal to the rising threshold value and startup-alarm is equal to
rising or either, then a single rising threshold crossing event is generated. If the first sample is
less than or equal to the falling threshold value and startup-alarm is equal to falling or either, a
single falling threshold crossing event is generated.
Values
rising, falling, either
Default
either
Configuration example:
cflash-cap-warn cf1-B: rising-threshold 2000000 falling-threshold 1999900 interval 240 rmonevent-type trap start-alarm either
event
Syntax
Context
Description
event rmon-event-id [event-type] [description description-string] [owner owner-string]
no event rmon-event-id
config>system>thresholds>rmon
The event command configures an entry in the RMON-MIB event table. The event command
controls the generation and notification of threshold crossing events configured with the alarm
command. When a threshold crossing event is triggered, the rmon>event configuration optionally
specifies if an entry in the RMON-MIB log table should be created to record the occurrence of the
event. It may also specify that an SNMP notification (trap) should be generated for the event. The
RMON-MIB defines two notifications for threshold crossing events: Rising Alarm and Falling
Alarm.
Creating an event entry in the RMON-MIB log table does not create a corresponding entry in the
TiMOS event logs. However, when the event-type is set to trap, the generation of a Rising Alarm or
Falling Alarm notification creates an entry in the TiMOS event logs and that is distributed to
whatever TiMOS log destinations are configured: CONSOLE, session, memory, file, syslog, or
SNMP trap destination.
Page 236
7210 SAS D, E OS Basic System Configuration Guide
System Management
The TiMOS logger message includes a rising or falling threshold crossing event indicator, the sample
type (absolute or delta), the sampled value, the threshold value, the RMON-alarm-id, the associated
RMON-event-id and the sampled SNMP object identifier.
Use the no form of this command to remove an rmon-event-id from the configuration.
Parameters
rmon-event-type — The rmon-event-type specifies the type of notification action to be taken when
this event occurs.
Values
log — In the case of log, an entry is made in the RMON-MIB log table for each
event occurrence.
This does not create a TiMOS logger entry. The RMON-MIB log table entries can
be viewed using the show>system>thresholds CLI command.
trap — In the case of trap, a TiMOS logger event is generated. The TiMOS logger
utility then distributes the notification of this event to its configured log
destinations which may be CONSOLE, telnet session , memory log, cflash file,
syslog, or SNMP trap destinations logs.
both — In the case of both, both a entry in the RMON-MIB logTable and a TiMOS
logger event are generated.
none — In the case of none, no action is taken.
Default
both
description — The description is a user configurable string that can be used to identify the purpose
of this event. This is an optional parameter and can be 80 characters long. If the string contains
special characters (#, $, spaces, etc.), the entire string must be enclosed within double quotes.
Default
An empty string.
owner owner — The owner identifies the creator of this alarm. It defaults to "TiMOS CLI". This
parameter is defined primarily to allow entries that have been created in the RMON-MIB
alarmTable by remote SNMP managers to be saved and reloaded in a CLI configuration file. The
owner will not normally be configured by CLI users and can be a maximum of 80 characters
long.
Default
TiMOS CLI
Configuration example:
Default
event 5 rmon-event-type both description "alarm testing" owner "TiMOS CLI"
7210 SAS D, E OS Basic System Configuration Guide
Page 237
System Alarm Commands
memory-use-alarm
Syntax
Context
Description
memory-use-alarm rising-threshold threshold [falling-threshold threshold] interval
seconds [rmon-event-type] [startup-alarm alarm-type]
no memory-use-alarm
config>system>thresholds
The memory thresholds are based on monitoring the TIMETRA-SYSTEM-MIB sgiMemoryUsed
object. This object contains the amount of memory currently used by the system. The severity level is
Alarm. The absolute sample type method is used.
The no form of this command removes the configured memory threshold warning.
Parameters
rising-threshold threshold — Specifies a threshold for the sampled statistic. When the current
sampled value is greater than or equal to this threshold, and the value at the last sampling interval
was less than this threshold, a single threshold crossing event will be generated. A single
threshold crossing event will also be generated if the first sample taken is greater than or equal to
this threshold and the associated startup-alarm is equal to rising or either.
After a rising threshold crossing event is generated, another such event will not be generated
until the sampled value falls below this threshold and reaches less than or equal the fallingthreshold value.
Default
0
Values
-2147483648 — 2147483647
falling-threshold threshold — Specifies a threshold for the sampled statistic. When the current
sampled value is less than or equal to this threshold, and the value at the last sampling interval
was greater than this threshold, a single threshold crossing event will be generated. A single
threshold crossing event will also be generated if the first sample taken is less than or equal to
this threshold and the associated startup-alarm is equal to falling or either.
After a rising threshold crossing event is generated, another such event will not be generated
until the sampled value raises above this threshold and reaches greater than or equal the risingthreshold threshold value.
Default
0
Values
-2147483648 — 2147483647
interval seconds — Specifies the polling period over which the data is sampled and compared with
the rising and falling thresholds.
Values
1 — 2147483647
rmon-event-type — Specifies the type of notification action to be taken when this event occurs.
Values
log — In the case of log, an entry is made in the RMON-MIB log table for each
event occurrence. This does not create an OS logger entry. The RMON-MIB log
table entries can be viewed using the CLI command.
trap — In the case of trap, a TiMOS logger event is generated. The TiMOS logger
utility then distributes the notification of this event to its configured log
Page 238
7210 SAS D, E OS Basic System Configuration Guide
System Management
destinations which may be CONSOLE, telnet session , memory log, cflash file,
syslog, or SNMP trap destinations logs.
both — In the case of both, both a entry in the RMON-MIB logTable and a TiMOS
logger event are generated.
none — In the case of none, no action is taken.
Default
both
startup-alarm alarm-type — Specifies the alarm that may be sent when this alarm is first created. If
the first sample is greater than or equal to the rising threshold value and startup-alarm is equal to
rising or either, then a single rising threshold crossing event is generated. If the first sample is
less than or equal to the falling threshold value and startup-alarm is equal to falling or either, a
single falling threshold crossing event is generated.
Values
rising, falling, either
Default
either
Configuration example:
memory-use-alarm rising-threshold 50000000 falling-threshold 45999999 interval 500 rmonevent-type both start-alarm either
memory-use-warn
Syntax
Context
Description
memory-use-warn rising-threshold threshold [falling-threshold threshold] interval
seconds [rmon-event-type] [startup-alarm alarm-type]
no memory-use-warn
config>system>thresholds
The memory thresholds are based on monitoring MemoryUsed object. This object contains the
amount of memory currently used by the system. The severity level is Alarm.
The absolute sample type method is used.
The no form of this command removes the configured compact flash threshold warning.
Parameters
rising-threshold threshold — The rising-threshold specifies a threshold for the sampled statistic.
When the current sampled value is greater than or equal to this threshold, and the value at the last
sampling interval was less than this threshold, a single threshold crossing event will be
generated. A single threshold crossing event will also be generated if the first sample taken is
greater than or equal to this threshold and the associated startup-alarm is equal to rising or either.
After a rising threshold crossing event is generated, another such event will not be generated
until the sampled value falls below this threshold and reaches less than or equal the fallingthreshold value.
Default
0
Values
-2147483648 — 2147483647
7210 SAS D, E OS Basic System Configuration Guide
Page 239
System Alarm Commands
falling-threshold threshold — The falling-threshold specifies a threshold for the sampled statistic.
When the current sampled value is less than or equal to this threshold, and the value at the last
sampling interval was greater than this threshold, a single threshold crossing event will be
generated. A single threshold crossing event will also be generated if the first sample taken is
less than or equal to this threshold and the associated startup-alarm is equal to falling or either.
After a rising threshold crossing event is generated, another such event will not be generated
until the sampled value raises above this threshold and reaches greater than or equal the risingthreshold threshold value.
Default
0
Values
-2147483648 — 2147483647
interval seconds — The interval in seconds specifies the polling period over which the data is
sampled and compared with the rising and falling thresholds.
Values
1 — 2147483647
rmon-event-type — Specifies the type of notification action to be taken when this event occurs.
Values
log — In the case of log, an entry is made in the RMON-MIB log table for each
event occurrence.
This does not create a TiMOS logger entry. The RMON-MIB log table entries can
be viewed using the show>system>thresholds CLI command.
trap — In the case of trap, a TiMOS logger event is generated. The TiMOS logger
utility then distributes the notification of this event to its configured log
destinations which may be CONSOLE, telnet session , memory log, cflash file,
syslog, or SNMP trap destinations logs.
both — In the case of both, both a entry in the RMON-MIB logTable and a TiMOS
logger event are generated.
none — In the case of none, no action is taken.
Default
both
Values
log, trap, both, none
startup-alarm alarm-type — Specifies the alarm that may be sent when this alarm is first created. If
the first sample is greater than or equal to the rising threshold value and startup-alarm is equal to
rising or either, then a single rising threshold crossing event is generated. If the first sample is
less than or equal to the falling threshold value and startup-alarm is equal to falling or either, a
single falling threshold crossing event is generated.
Default
either
Values
rising, falling, either
Configuration example:
memory-use-warn rising-threshold 500000 falling-threshold 400000 interval 800 rmonevent-type log start-alarm falling
Page 240
7210 SAS D, E OS Basic System Configuration Guide
System Management
rmon
Syntax
Context
Description
rmon
config>system>thresholds
This command creates the context to configure generic RMON alarms and events.
Generic RMON alarms can be created on any SNMP object-ID that is valid for RMON monitoring
(for example, an integer-based datatype).
The configuration of an event controls the generation and notification of threshold crossing events
configured with the alarm command.
thresholds
Syntax
Context
Description
thresholds
config>system
This command enables the context to configure monitoring thresholds.
7210 SAS D, E OS Basic System Configuration Guide
Page 241
Date and Time Commands
Date and Time Commands
set-time
Syntax
Context
Description
set-time [date] [time]
admin
This command sets the local system time.
The time entered should be accurate for the time zone configured for the system. The system will
convert the local time to UTC before saving to the system clock which is always set to UTC. This
command does not take into account any daylight saving offset if defined.
Parameters
date — The local date and time accurate to the minute in the YYYY/MM/DD format.
Values
YYYY is the four-digit year
MM is the two-digit month
DD is the two-digit date
time — The time (accurate to the second) in the hh:mm[:ss] format. If no seconds value is entered, the
seconds are reset to :00.
Default
0
Values
hh is the two-digit hour in 24 hour format (00=midnight, 12=noon)
mm is the two-digit minute
time
Syntax
Context
Description
Page 242
time
config>system
This command enables the context to configure the system time zone and time synchronization
parameters.
7210 SAS D, E OS Basic System Configuration Guide
System Management
Network Time Protocol Commands
ntp
Syntax
Context
Description
Default
[no] ntp
config>system>time
This command enables the context to configure Network Time Protocol (NTP) and its operation. This
protocol defines a method to accurately distribute and maintain time for network elements.
Furthermore this capability allows for the synchronization of clocks between the various network
elements. Use the no form of the command to stop the execution of NTP and remove its
configuration.
none
authentication-check
Syntax
Context
Description
[no] authentication-check
config>system>time>ntp
This command provides the option to skip the rejection of NTP PDUs that do not match the
authentication key-id, type or key requirements. The default behavior when authentication is
configured is to reject all NTP protocol PDUs that have a mismatch in either the authentication keyid, type or key.
When authentication-check is enabled, NTP PDUs are authenticated on receipt. However,
mismatches cause a counter to be increased, one counter for type and one for key-id, one for type,
value mismatches. These counters are visible in a show command.
The no form of this command allows authentication mismatches to be accepted; the counters however
are maintained.
Default
authentication-check — Rejects authentication mismatches.
7210 SAS D, E OS Basic System Configuration Guide
Page 243
Date and Time Commands
authentication-key
Syntax
Context
Description
authentication-key key-id {key key} [hash | hash2] type {des | message-digest}
no authentication-key key-id
config>system>time>ntp
This command sets the authentication key-id, type and key used to authenticate NTP PDUs sent to or
received by other network elements participating in the NTP protocol. For authentication to work, the
authentication key-id, type and key value must match.
The no form of the command removes the authentication key.
Default
Parameters
none
key-id — Configure the authentication key-id that will be used by the node when transmitting or
receiving Network Time Protocol packets.
Entering the authentication-key command with a key-id value that matches an existing
configuration key will result in overriding the existing entry.
Recipients of the NTP packets must have the same authentication key-id, type, and key value in
order to use the data transmitted by this node. This is an optional parameter.
Default
None
Values
1 — 255
key — The authentication key associated with the configured key-id, the value configured in this
parameter is the actual value used by other network elements to authenticate the NTP packet.
The key can be any combination of ASCII characters up to 32 characters in length for messagedigest (md5) or 8 characters in length for des (length limits are unencrypted lengths). If spaces
are used in the string, enclose the entire string in quotation marks (“.”).
hash — Specifies the key is entered in an encrypted form. If the hash or hash2 parameter is not used,
the key is assumed to be in a non-encrypted, clear text form. For security, all keys are stored in
encrypted form in the configuration file with the hash or hash2 parameter specified.
hash2 — Specifies the key is entered in a more complex encrypted form that involves more
variables then the key value alone, this means that hash2 encrypted variable can’t be copied and
pasted. If the hash or hash2 parameter is not used, the key is assumed to be in a non-encrypted,
clear text form. For security, all keys are stored in encrypted form in the configuration file with
the hash or hash2 parameter specified.
type — This parameter determines if DES or message-digest authentication is used.
This is a required parameter; either DES or message-digest must be configured.
Values
Page 244
des — Specifies that DES authentication is used for this key
message-digest — Specifies that MD5 authentication in accordance with RFC 2104
is used for this key.
7210 SAS D, E OS Basic System Configuration Guide
System Management
broadcast
Syntax
Context
Description
broadcast [router router-name] {interface ip-int-name} [key-id key-id] [version version]
[ttl ttl]
no broadcast [router router-name] {interface ip-int-name}
config>system>time>ntp
This command configures the node to transmit NTP packets on a given interface. Broadcast and
multicast messages can easily be spoofed, thus, authentication is strongly recommended.
The no form of this command removes the address from the configuration.
Parameters
router — Specifies the router name used to transmit NTP packets. Base is the default and the only
router name supported currently.
Values
Base
Default
Base
ip-int-name — Specifies the local interface on which to transmit NTP broadcast packets. If the string
contains special characters (#, $, spaces, etc.), the entire string must be enclosed within double
quotes.
Values
32 character maximum
key-id key-id — Identifies the configured authentication key and authentication type used by this
node to receive and transmit NTP packets to and from an NTP server and peers. If an NTP packet
is received by this node both authentication key and authentication type must be valid otherwise
the packet will be rejected and an event/trap generated.
Values
1 — 255
Default
none
version version — Specifies the NTP version number that is generated by this node. This parameter
does not need to be configured when in client mode in which case all versions will be accepted.
Values
1—4
Default
4
ttl ttl — Specifies the IP Time To Live (TTL) value.
Values
1 — 255
Default
none
7210 SAS D, E OS Basic System Configuration Guide
Page 245
Date and Time Commands
broadcastclient
Syntax
Context
Description
broadcastclient [router router-name] {interface ip-int-name} [authenticate]
no broadcastclient [router router-name] {interface ip-int-name}
config>system>time>ntp
When configuring NTP, the node can be configured to receive broadcast packets on a given subnet.
Broadcast and multicast messages can easily be spoofed, thus, authentication is strongly
recommended. If broadcast is not configured then received NTP broadcast traffic will be ignored. Use
the show command to view the state of the configuration.
The no form of this command removes the address from the configuration.
Parameters
router router-name — Specifies the router name used to receive NTP packets.
Values
Base
Default
Base
interface ip-int-name — Specifies the local interface on which to receive NTP broadcast packets. If
the string contains special characters (#, $, spaces, etc.), the entire string must be enclosed within
double quotes.
Values
32 character maximum
authenticate — Specifies whether or not to require authentication of NTP PDUs. When enabled,
NTP PDUs are authenticated upon receipt.
ntp-server
Syntax
Context
Description
Default
Parameters
Page 246
ntp-server [transmit key-id]
no ntp-server
config>system>time>ntp
This command configures the node to assume the role of an NTP server. Unless the server command
is used, this node will function as an NTP client only and will not distribute the time to downstream
network elements.
no ntp-server
key-id — If specified, requires client packets to be authenticated.
Values
1 — 255
Default
None
7210 SAS D, E OS Basic System Configuration Guide
System Management
peer
Syntax
Context
Description
peer ip-address [key-id key-id] [version version] [prefer]
no peer ip-address
config>system>time>ntp
Configuration of an NTP peer configures symmetric active mode for the configured peer. Although
any system can be configured to peer with any other NTP node it is recommended to configure
authentication and to configure known time servers as their peers.
The no form of the command removes the configured peer.
Parameters
ip-address — Configure the IP address of the peer that requires a peering relationship to be set up.
This is a required parameter.
Default
None
Values
Any valid IP-address
key-id key-id — Successful authentication requires that both peers must have configured the same
authentication key-id, type and key value.
Specify the key-id that identifies the configured authentication key and authentication type used
by this node to transmit NTP packets to an NTP peer. If an NTP packet is received by this node,
the authentication key-id, type, and key value must be valid otherwise the packet will be rejected
and an event/trap generated.
Default
None
Values
1 — 255
version version — Specify the NTP version number that is generated by this node. This parameter
does not need to be configured when in client mode in which case all three nodes are accepted.
Default
4
Values
2—4
prefer — When configuring more than one peer, one remote system can be configured as the
preferred peer. When a second peer is configured as preferred, then the new entry overrides the
old entry.
7210 SAS D, E OS Basic System Configuration Guide
Page 247
Date and Time Commands
server
Syntax
Context
Description
server ip address [key-id key-id] [version version] [prefer]
no server ip address
config>system>time>ntp
This command is used when the node should operate in client mode with the ntp server specified in
the address field of this command. The no construct of this command removes the server with the
specified address from the configuration.
Up to five NTP servers can be configured.
Parameters
ip-address — Configure the IP address of a node that acts as an NTP server to this network element.
This is a required parameter.
Values
Any valid IP address
key-id key-id — Enter the key-id that identifies the configured authentication key and authentication
type used by this node to transmit NTP packets to an NTP server. If an NTP packet is received by
this node, the authentication key-id, type, and key value must be valid otherwise the packet will
be rejected and an event/trap generated. This is an optional parameter.
Values
1 — 255
version version — Use this command to configure the NTP version number that is expected by this
node. This is an optional parameter
Default
4
Values
2—4
prefer — When configuring more than one peer, one remote system can be configured as the
preferred peer. When a second peer is configured as preferred, then the new entry overrides the
old entry.
Page 248
7210 SAS D, E OS Basic System Configuration Guide
System Management
SNTP Commands
sntp
Syntax
Context
Description
[no] sntp
config>system>time
This command creates the context to edit the Simple Network Time Protocol (SNTP).
SNTP can be configured in either broadcast or unicast client mode. SNTP is a compact, client-only
version of the NTP. SNTP can only receive the time from SNTP/NTP servers. It cannot be used to
provide time services to other systems.
The system clock is automatically adjusted at system initialization time or when the protocol first
starts up.
When the time differential between the SNTP/NTP server and the system is more than 2.5 seconds,
the time on the system is gradually adjusted.
SNTP is created in an administratively enabled state (no shutdown).
The no form of the command removes the SNTP instance and configuration. SNTP does not need to
be administratively disabled when removing the SNTP instance and configuration.
Default
no sntp
broadcast-client
Syntax
Context
Description
[no] broadcast-client
config>system>time>sntp
This command enables listening to SNTP/NTP broadcast messages on interfaces with broadcast
client enabled at global device level.
SNTP must be shutdown prior to changing either to or from broadcast mode.
The no form of the command disables broadcast client mode.
Default
no broadcast-client
7210 SAS D, E OS Basic System Configuration Guide
Page 249
Date and Time Commands
server-address
Syntax
Context
server-address ip-address [version version-number] [normal | preferred]
[interval seconds]
no server-address
config>system>time>sntp
Description
This command creates an SNTP server for unicast client mode.
Parameters
ip-address — Specifies the IP address of the SNTP server.
version version-number — Specifies the SNTP version supported by this server.
Values
1—3
Default
3
normal | preferred — Specifies the preference value for this SNTP server. When more than one
time-server is configured, one server can have preference over others. The value for that server
should be set to preferred. Only one server in the table can be a preferred server.
Default
normal
interval seconds — Specifies the frequency at which this server is queried.
Page 250
Values
64 — 1024
Default
64
7210 SAS D, E OS Basic System Configuration Guide
System Management
CRON Commands
cron
Syntax
cron
Context
config
Description
This command creates the context to create scripts, script parameters and schedules which support the
Service Assurance Agent (SAA) functions.
CRON features are saved to the configuration file on both primary and backup control modules. If a
control module switchover occurs, CRON events are restored when the new configuration is loaded.
If a control module switchover occurs during the execution of a cron script, the failover behavior will
be determined by the contents of the script.
action
Syntax
Context
Description
Default
Parameters
[no] action action-name [owner action-owner]
config>cron
config>cron>sched
This command configures action parameters for a script.
none
action action-name — Specifies the action name.
Values
Maximum 32 characters.
owner action-owner — Specifies the owner name.
Default
TiMOS CLI
expire-time
Syntax
Context
expire-time {seconds | forever}
config>cron>action
Description
This command configures the maximum amount of time to keep the results from a script run.
Parameters
seconds — Specifies the maximum amount of time to keep the results from a script run.
Values
1 — 21474836
Default
3600 (1 hour)
forever — Specifies to keep the results from a script run forever.
7210 SAS D, E OS Basic System Configuration Guide
Page 251
Date and Time Commands
lifetime
Syntax
Context
lifetime {seconds | forever}
config>cron>action
Description
This command configures the maximum amount of time the script may run.
Parameters
seconds — Specifies the maximum amount of time to keep the results from a script run.
Values
1 — 21474836
Default
3600 (1 hour)
forever — Specifies to keep the results from a script run forever.
max-completed
Syntax
Context
Description
max-completed unsigned
config>cron>action
This command specifies the maximum number of completed sessions to keep in the event execution
log. If a new event execution record exceeds the number of records specified this command, the
oldest record is deleted.
The no form of this command resets the value to the default.
Parameters
unsigned — Specifies the maximum number of completed sessions to keep in the event execution log.
Values
0 — 255
Default
1
results
Syntax
[no] results file-url
Context
config>cron>action
Description
This command specifies the location where the system writes the output of an event script’s
execution.
The no form of this command removes the file location from the configuration.
Parameters
file-url — Specifies the location where the system writes the output of an event script’s execution.
Values
file url:
local-url:
remote-url:
cflash-id:
Page 252
local-url | remote-url: 255 chars max
[cflash-id/][file-path]
[{ftp://} login:pswd@remote-locn/][file-path]
remote-locn [ hostname | ipv4-address]
ipv4-address
a.b.c.d
cf1:
7210 SAS D, E OS Basic System Configuration Guide
System Management
script
Syntax
Context
Description
[no] script script-name [owner owner-name]
config>cron>action
This command creates action parameters for a script including the maximum amount of time to keep
the results from a script run, the maximum amount of time a script may run, the maximum number of
script runs to store and the location to store the results.
The no form of this command removes the script parameters from the configuration.
Default
Parameters
none — No server-address is configured.
script script-name — The script command in the action context connects and event to the script
which will run when the event is triggered.
owner owner-name — Owner name of the schedule.
Default
TiMOS CLI
The no form of this command removes the script entry from the action context.
schedule
Syntax
Context
Description
[no] schedule schedule-name [owner owner-name]
config>cron
This command configures the type of schedule to run, including one-time only (oneshot), periodic or
calendar-based runs. All runs are determined by month, day of month or weekday, hour, minute and
interval (seconds).
The no form of the command removes the context from the configuration.
Default
Parameters
none
schedule-name — Name of the schedule.
owner owner-name — Owner name of the schedule.
count
Syntax
Context
count number
config>cron>sched
Description
This command configures the total number of times a CRON “interval” schedule is run. For example,
if the interval is set to 600 and the count is set to 4, the schedule runs 4 times at 600 second intervals.
Parameters
number — The number of times the schedule is run.
7210 SAS D, E OS Basic System Configuration Guide
Page 253
Date and Time Commands
Values
1 — 65535
Default
65535
day-of-month
Syntax
Context
Description
[no] day-of-month {day-number [..day-number] all}
config>cron>sched
This command specifies which days of the month that the schedule will occur. Multiple days of the
month can be specified. When multiple days are configured, each of them will cause the schedule to
trigger. If a day-of-month is configured without configuring month, weekday, hour and minute, the
event will not execute.
Using the weekday command as well as the day-of-month command will cause the script to run
twice. For example, consider that “today” is Monday January 1. If “Tuesday January 5” is configured,
the script will run on Tuesday (tomorrow) as well as January 5 (Friday).
The no form of this command removes the specified day-of-month from the list.
Parameters
day-number — The positive integers specify the day of the month counting from the first of the
month. The negative integers specify the day of the month counting from the last day of the
month. For example, configuring day-of-month -5, 5 in a month that has 31 days will specify the
schedule to occur on the 27th and 5th of that month.
Integer values must map to a valid day for the month in question. For example, February 30 is
not a valid date.
Values
1 — 31, -31 — -1 (maximum 62 day-numbers)
all — Specifies all days of the month.
end-time
Syntax
Context
Description
[no] end-time [date | day-name] time
config>cron>sched
This command is used concurrently with type periodic or calendar. Using the type of periodic, endtime determines at which interval the schedule will end. Using the type of calendar, end-time
determines on which date the schedule will end.
When no end-time is specified, the schedule runs forever.
Parameters
date — Specifies the date to schedule a command.
Values
YYYY:MM:DD in year:month:day number format
day-name — Specifies the day of the week to schedule a command.
Values
sunday|monday|tuesday|wednesday|thursday|friday|saturday
time — Specifies the time of day to schedule a command.
Page 254
7210 SAS D, E OS Basic System Configuration Guide
System Management
Values
hh:mm in hour:minute format
hour
Syntax
Context
Description
[no] hour {..hour-number [..hour-number]| all}
config>cron>sched
This command specifies which hour to schedule a command. Multiple hours of the day can be
specified. When multiple hours are configured, each of them will cause the schedule to trigger. Dayof-month or weekday must also be specified. All days of the month or weekdays can be specified. If
an hour is configured without configuring month, weekday, day-of-month, and minute, the event will
not execute.
The no form of this command removes the specified hour from the configuration.
Parameters
hour-number — Specifies the hour to schedule a command.
Values
0 — 23 (maximum 24 hour-numbers)
all — Specifies all hours.
interval
Syntax
Context
[no] interval seconds
config>cron>sched
Description
This command specifies the interval between runs of an event.
Parameters
seconds — The interval, in seconds, between runs of an event.
Values
30 — 4,294,967,295
minute
Syntax
Context
Description
[no] minute {minute-number [..minute-number]| all}
config>cron>sched
This command specifies the minute to schedule a command. Multiple minutes of the hour can be
specified. When multiple minutes are configured, each of them will cause the schedule to occur. If a
minute is configured, but no hour or day is configured, the event will not execute. If a minute is
configured without configuring month, weekday, day-of-month, and hour, the event will not execute.
The no form of this command removes the specified minute from the configuration.
Parameters
minute-number — Specifies the minute to schedule a command.
Values
0 — 59 (maximum 60 minute-numbers)
7210 SAS D, E OS Basic System Configuration Guide
Page 255
Date and Time Commands
all — Specifies all minutes.
month
Syntax
Context
Description
[no] month {month-number [..month-number]|month-name [..month-name]| all}
config>cron>sched
This command specifies the month when the event should be executed. Multiple months can be
specified. When multiple months are configured, each of them will cause the schedule to trigger. If a
month is configured without configuring weekday, day-of-month, hour and minute, the event will not
execute.
The no form of this command removes the specified month from the configuration.
Parameters
month-number — Specifies a month number.
Values
1 —12 (maximum 12 month-numbers)
all — Specifies all months.
month-name — Specifies a month by name
Values
Page 256
january, february, march, april, may, june, july, august, september, october, november, december (maximum 12 month names)
7210 SAS D, E OS Basic System Configuration Guide
System Management
type
Syntax
Context
type {schedule-type}
config>cron>sched
Description
This command specifies how the system should interpret the commands contained within the
schedule node.
Parameters
schedule-type — Specify the type of schedule for the system to interpret the commands contained
within the schedule node.
Values
periodic — Specifies a schedule which runs at a given interval. interval must be
specified for this feature to run successfully.
calendar — Specifies a schedule which runs based on a calendar. weekday, month,
day-of-month, hour and minute must be specified for this feature to run successfully.
oneshot — Specifies a schedule which runs one time only. As soon as the first
event specified in these parameters takes place and the associated event occurs, the
schedule enters a shutdown state. month, weekday, day-of-month, hour and minute
must be specified for this feature to run successfully.
Default
periodic
weekday
Syntax
Context
Description
[no] weekday {weekday-number [..weekday-number]|day-name [..day-name]| all}
config>cron>sched
This command specifies which days of the week that the schedule will fire on. Multiple days of the
week can be specified. When multiple days are configured, each of them will cause the schedule to
occur. If a weekday is configured without configuring month, day-of-month, hour and minute, the
event will not execute.
Using the weekday command as well as the day-of month command will cause the script to run
twice. For example, consider that “today” is Monday January 1. If “Tuesday January 5” is configured,
the script will run on Tuesday (tomorrow) as well as January 5 (Friday).
The no form of this command removes the specified weekday from the configuration.
Parameters
day-number — Specifies a weekday number.
Values
1 —7 (maximum 7 week-day-numbers)
day-name — Specifies a day by name
Values
sunday, monday, tuesday, wednesday, thursday, friday, saturday (maximum 7 weekday names)
all — Specifies all days of the week.
7210 SAS D, E OS Basic System Configuration Guide
Page 257
Date and Time Commands
script
Syntax
Context
[no] script script-name [owner owner-name]
config>cron>script
Description
This command configures the name associated with this script.
Parameters
script-name — Specifies the script name.
location
Syntax
Context
[no] location file-url
config>cron>script
Description
This command configures the location of script to be scheduled.
Parameters
file-url — Specifies the location where the system writes the output of an event script’s execution.
Values
file url:
local-url:
remote-url:
cflash-id:
Page 258
local-url | remote-url: 255 chars max
[cflash-id/][file-path]
[{ftp://} login:pswd@remote-locn/][file-path]
remote-locn [ hostname | ipv4-address]
ipv4-address
a.b.c.d
cf1:
7210 SAS D, E OS Basic System Configuration Guide
System Management
Time Range Commands
time-range
Syntax
Context
Description
[no] time-range name [create]
config>cron
This command configures a time range.
The no form of the command removes the name from the configuration.
Default
Parameters
none
name — Configures a name for the time range up to 32 characters in length.
absolute
Syntax
Context
Description
absolute start start-absolute-time end end-absolute-time
no absolute start absolute-time
config>cron>time-range
This command configures an absolute time interval that will not repeat.
The no form of the command removes the absolute time range from the configuration.
Parameters
start absolute-time — Specifies starting parameters for the absolute time-range.
Values
absolute-time:
year:
month:
day:
hh:
mm: [
year/month/day,hh:mm
2005 — 2099
1 — 12
1 — 31
0 — 23
0 — 59
end absolute-time — Specifies end parameters for the absolute time-range.
Values
absolute-time:
year:
month:
day:
hh:
mm: [
year/month/day,hh:mm
2005 — 2099
1 — 12
1 — 31
0 — 23
0 — 59
7210 SAS D, E OS Basic System Configuration Guide
Page 259
Date and Time Commands
daily
Syntax
Context
Description
daily start start-time-of-day end end-time-of-day
no daily start start-time-of-day
config>cron>time-range
This command configures the start and end of a schedule for every day of the week. To configure a
daily time-range across midnight, use a combination of two entries. An entry that starts at hour zero
will take over from an entry that ends at hour 24.
The no form of the command removes the daily time parameters from the configuration.
Parameters
start-time-of-day — Specifies the starting time for the time range.
Values
Syntax:
hh:mm
hh
0 — 23
mm
0 — 59
end-time-of-day — Specifies the ending time for the time range.
Values
Syntax:
hh:mm
hh
0 — 24
mm
0 — 59
weekdays
Syntax
Context
Description
weekdays start start-time-of-day end end-time-of-day
no weekdays start start-time-of-day
config>cron>time-range
This command configures the start and end of a weekday schedule.
The no form of the command removes the weekday parameters from the configuration.
Parameters
start-time-of-day — Specifies the starting time for the time range.
Values
Syntax:
hh:mm
hh
0 — 23
mm
0 — 59
end-time-of-day — Specifies the ending time for the time range.
Values
Page 260
Syntax:
hh:mm
hh
0 — 24
mm
0 — 59
7210 SAS D, E OS Basic System Configuration Guide
System Management
weekend
Syntax
Context
Description
weekend start start-time-of-day end end-time-of-day
no weekend start start-time-of-day
config>cron>time-range
This command configures a time interval for every weekend day in the time range.
The resolution must be at least one minute apart, for example, start at 11:00 and end at 11:01. An
11:00 start and end time is invalid. This example configures a start at 11:00 and an end at 11:01 on
both Saturday and Sunday.
The no form of the command removes the weekend parameters from the configuration.
Parameters
start-time-of-day — Specifies the starting time for the time range.
Values
Syntax:
hh:mm
hh
0 — 23
mm
0 — 59
end-time-of-day — Specifies the ending time for the time range.
Values
Syntax:
hh:mm
hh
0 — 24
mm
0 — 59
weekly
Syntax
Context
Description
weekly start start-time-in-week end end-time-in-week
no weekly start start-time-in-week
config>cron>time-range
This command configures a weekly periodic interval in the time range.
The no form of the command removes the weekly parameters from the configuration.
Parameters
start-time-in-week — Specifies the start day and time of the week.
Values
Syntax:
day,hh:mm
day
hh
mm
sun, mon, tue, wed, thu, fri, sat
sunday, monday, tuesday, wednesday, thursday, friday,
saturday
0 — 23
0 — 59
end-time-in-week — Specifies the end day and time of the week.
Values
Values
Syntax:
day,hh:mm
day
sun, mon, tue, wed, thu, fri, sat
sunday, monday, tuesday, wednesday, thursday, friday,
saturday
7210 SAS D, E OS Basic System Configuration Guide
Page 261
Date and Time Commands
hh
mm
0 — 24
0 — 59
weekly start time-in-week end time-in-week — This parameter configures the start and end of a
schedule for the same day every week, for example, every Friday. The start and end dates must
be the same. The resolution must be at least one minute apart, for example, start at 11:00 and end
at 11:01. A start time and end time of 11:00 is invalid.
Values
Default
Page 262
00 — 23, 00 — 59
no time-range
7210 SAS D, E OS Basic System Configuration Guide
System Management
Time of Day Commands
tod-suite
Syntax
Context
Description
[no] tod-suite tod-suite name create
config>cron
This command creates the tod-suite context.
Default
no tod-suite
Syntax
egress
egress
Context
Description
config>cron>tod-suite
This command enables the TOD suite egress parameters.
ingress
Syntax
Context
Description
ingress
config>cron>tod-suite
This command enables the TOD suite ingress parameters.
filter
Syntax
Context
filter ip ip-filter-id [time-range time-range-name] [priority priority]
filter mac mac-filter-id [time-range time-range-name] [priority priority]
no ip ip-filter-id [time-range time-range-name]
no filter mac mac-filter-id [time-range time-range-name]
config>cron>tod-suite>egress
config>cron>tod-suite>ingress
Description
This command creates time-range based associations of previously created filter policies. Multiple
policies may be included and each must be assigned a different priority; in case time-ranges overlap,
the priority will be used to determine the prevailing policy. Only a single reference to a policy may be
included without a time-range.
Parameters
ip-filter ip-filter-id — Specifies an IP filter for this tod-suite.
7210 SAS D, E OS Basic System Configuration Guide
Page 263
Date and Time Commands
Values
1 — 65535
time-range time-range-name — Name for the specified time-range. If the time-range is not
populated the system will assume the assignment to mean “all times”. Only one entry without a
time-range is allowed for every type of policy. The system does not allow the user to specify
more than one policy with the same time-range and priority.
Values
Up to 32 characters
priority priority — Priority of the time-range. Only one time-range assignment of the same type and
priority is allowed.
Values
1 — 10
mac mac-filter-id — Specifies a MAC filter for this tod-suite.
Values
1 — 65535
qos
Syntax
Context
Description
qos policy-id [time-range time-range-name] [priority priority]
no qos policy-id [time-range time-range-name] [
config>cron>tod-suite>ingress
This command creates time-range based associations of previously created QoS policies. Multiple
policies may be included and each must be assigned a different priority; in case time-ranges overlap,
the priority will be used to determine the prevailing policy. Only a single reference to a policy may be
included without a time-range.
The no form of the command reverts to the
Parameters
policy-id — Specifies an egress QoS policy for this tod-suite.
Values
1 — 65535
time-range time-range-name — Name for the specified time-range. If the time-range is not
populated the system will assume the assignment to mean “all times”. Only one entry without a
time-range is allowed for every type of policy. The system does not allow the user to specify
more than one policy with the same time-range and priority.
Values
Up to 32 characters
Default
"NO-TIME-RANGE" policy
priority priority — Priority of the time-range. Only one time-range assignment of the same type and
priority is allowed.
Page 264
Values
1 — 10
Default
5
7210 SAS D, E OS Basic System Configuration Guide
System Management
System Time Commands
dst-zone
Syntax
Context
Description
[no] dst-zone [std-zone-name | non-std-zone-name]
config>system>time
This command configures the start and end dates and offset for summer time or daylight savings time
to override system defaults or for user defined time zones.
When configured, the time is adjusted by adding the configured offset when summer time starts and
subtracting the configured offset when summer time ends.
If the time zone configured is listed in Table 17, System-defined Time Zones, on page 159, then the
starting and ending parameters and offset do not need to be configured with this command unless it is
necessary to override the system defaults. The command returns an error if the start and ending dates
and times are not available either in Table 17 on or entered as optional parameters in this command.
Up to five summer time zones may be configured, for example, for five successive years or for five
different time zones. Configuring a sixth entry will return an error message. If no summer (daylight
savings) time is supplied, it is assumed no summer time adjustment is required.
The no form of the command removes a configured summer (daylight savings) time entry.
Default
Parameters
none — No summer time is configured.
std-zone-name — The standard time zone name. The standard name must be a system-defined zone in
Table 17. For zone names in the table that have an implicit summer time setting, for example
MDT for Mountain Daylight Saving Time, the remaining start-date, end-date and offset
parameters need to be provided unless it is necessary to override the system defaults for the time
zone.
Values
std-zone-name ADT, AKDT, CDT, CEST, EDT, EEST, MDT, PDT, WEST
non-std-zone-name — The non-standard time zone name. Create a user-defined name created using
the zone command on page 268
Values
5 characters maximum
7210 SAS D, E OS Basic System Configuration Guide
Page 265
Date and Time Commands
end
Syntax
Context
end {end-week} {end-day} {end-month} [hours-minutes]
config>system>time>dst-zone
Description
This command configures start of summer time settings.
Parameters
end-week — Specifies the starting week of the month when the summer time will end.
Values
first, second, third, fourth, last
Default
first
end-day — Specifies the starting day of the week when the summer time will end.
Values
sunday, monday, tuesday, wednesday, thursday, friday, saturday
Default
sunday
end-month — The starting month of the year when the summer time will take effect.
Values
january, february, march, april, may, june, july, august, september, october, november, december}
Default
january
hours — Specifies the hour at which the summer time will end.
Values
0 — 24
Default
0
minutes — Specifies the number of minutes, after the hours defined by the hours parameter, when the
summer time will end.
Values
0 — 59
Default
0
offset
Syntax
Context
offset offset
config>system>time>dst-zone
Description
This command specifies the number of minutes that will be added to the time when summer time
takes effect. The same number of minutes will be subtracted from the time when the summer time
ends.
Parameters
offset — The number of minutes added to the time at the beginning of summer time and subtracted at
the end of summer time, expressed as an integer.
Default
Page 266
60
7210 SAS D, E OS Basic System Configuration Guide
System Management
Values
0 — 60
start
Syntax
Context
start {start-week} {start-day} {start-month} [hours-minutes]
config>system>time>dst-zone
Description
This command configures start of summer time settings.
Parameters
start-week — Specifies the starting week of the month when the summer time will take effect.
Values
first, second, third, fourth, last
Default
first
start-day — Specifies the starting day of the week when the summer time will take effect.
Default
sunday
Values
sunday, monday, tuesday, wednesday, thursday, friday, saturday
start-month — The starting month of the year when the summer time will take effect.
Values
january, february, march, april, may, june, july, august, september, october, november, december
Default
january
hours — Specifies the hour at which the summer time will take effect.
Default
0
minutes — Specifies the number of minutes, after the hours defined by the hours parameter, when the
summer time will take effect.
Default
0
7210 SAS D, E OS Basic System Configuration Guide
Page 267
Date and Time Commands
zone
Syntax
Context
Description
zone [std-zone-name | non-std-zone-name] [hh [:mm]]
no zone
config>system>time
This command sets the time zone and/or time zone offset for the device.
supports system-defined and user-defined time zones. The system-defined time zones are listed in
Table 17, System-defined Time Zones, on page 159.
For user-defined time zones, the zone and the UTC offset must be specified.
The no form of the command reverts to the default of Coordinated Universal Time (UTC). If the time
zone in use was a user-defined time zone, the time zone will be deleted. If a dst-zone command has
been configured that references the zone, the summer commands must be deleted before the zone can
be reset to UTC.
Default
Parameters
zone utc - The time zone is set for Coordinated Universal Time (UTC).
std-zone-name — The standard time zone name. The standard name must be a system-defined zone in
Table 17. For zone names in the table that have an implicit summer time setting, for example
MDT for Mountain Daylight Saving Time, the remaining start-date, end-date and offset
parameters need to be provided unless it is necessary to override the system defaults for the time
zone.
For system-defined time zones, a different offset cannot be specified. If a new time zone is
needed with a different offset, the user must create a new time zone. Note that some systemdefined time zones have implicit summer time settings which causes the switchover to summer
time to occur automatically; configuring the dst-zone parameter is not required.
A user-defined time zone name is case-sensitive and can be up to 5 characters in length.
Values
A user-defined value can be up to 4 characters or one of the following values:
GMT, BST, IST, WET, WEST, CET, CEST, EET, EEST, MSK, MSD, AST, ADT,
EST, EDT, ET, CST, CDT, CT, MST, MDT, MT, PST, PDT, PT, HST, AKST,
AKDT, WAST, CAST, EAST
non-std-zone-name — The non-standard time zone name.
Values
Up to 5 characters maximum.
hh [:mm] — The hours and minutes offset from UTC time, expressed as integers. Some time zones
do not have an offset that is an integral number of hours. In these instances, the minutes-offset
must be specified. For example, the time zone in Pirlanngimpi, Australia UTC + 9.5 hours.
Default
hours: 0
minutes: 0
Values
hours: -11 — 11
minutes: 0 — 59
Values
Page 268
7210 SAS D, E OS Basic System Configuration Guide
System Management
Generic Commands
shutdown
Syntax
Context
Description
[no] shutdown
config>system>time>sntp
This command administratively disables an entity. When disabled, an entity does not change, reset, or
remove any configuration settings or statistics.
The operational state of the entity is disabled as well as the operational state of any entities contained
within. Many objects must be shut down before they may be deleted.
The no form of this command administratively enables an entity.
Unlike other commands and parameters where the default state is not indicated in the configuration
file, the shutdown and no shutdown states are always indicated in system generated configuration
files.
The no form of the command places an entity in an administratively enabled state.
7210 SAS D, E OS Basic System Configuration Guide
Page 269
System Administration Commands
System Administration Commands
admin
Syntax
Context
Description
Default
admin
<ROOT>
The context to configure administrative system commands. Only authorized users can execute the
commands in the admin context.
none
check-golden-bootstrap
Syntax
Context
Description
check-golden-bootstrap
admin
This command validates the current golden bootstrap image, and displays its version, if found to be
valid. If the golden bootstrap image is not found to be a valid, an error message is displayed to that
effect.
debug-save
Syntax
Context
Description
Default
Parameters
debug-save file-url
admin
This command saves existing debug configuration. Debug configurations are not preserved in
configuration saves.
none
file-url — The file URL location to save the debug configuration.
Values
file url:
local-url:
remote-url:
cflash-id:
Page 270
local-url | remote-url: 255 chars max
[cflash-id/][file-path], 200 chars max, including the cflash-id
directory length, 99 chars max each
[{ftp://} login:pswd@remote-locn/][file-path]
remote-locn [ hostname | ipv4-address]
ipv4-address
a.b.c.d
255 chars max, directory length 99 chars max each
cf1:
7210 SAS D, E OS Basic System Configuration Guide
System Management
disconnect
Syntax
Context
Description
disconnect {address ip-address | username user-name | console | telnet | ftp | ssh}
admin
This command disconnects a user from a console, Telnet, FTP, or SSH session.
If any of the console, Telnet, FTP, or SSH options are specified, then only the respective console,
Telnet, FTP, or SSH sessions are affected.
If no console, Telnet, FTP, or SSH options are specified, then all sessions from the IP address or from
the specified user are disconnected.
Any task that the user is executing is terminated. FTP files accessed by the user will not be removed.
A major severity security log event is created specifying what was terminated and by whom.
Default
Parameters
none — No disconnect options are configured.
address ip-address — The IP address to disconnect, specified in dotted decimal notation.
Values
ipv4-address
a.b.c.d
username user-name — The name of the user.
console — Disconnects the console session.
telnet — Disconnects the Telnet session.
ftp — Disconnects the FTP session.
ssh — Disconnects the SSH session.
display-config
Syntax
Context
Description
display-config [detail | index]
admin
This command displays the system’s running configuration.
By default, only non-default settings are displayed.
Specifying the detail option displays all default and non-default configuration parameters.
Parameters
detail — Displays default and non-default configuration parameters.
index — Displays only persistent-indices.
reboot
7210 SAS D, E OS Basic System Configuration Guide
Page 271
System Administration Commands
Syntax
Context
Description
reboot [upgrade] [auto-init] [now]
admin
This command reboots the s or upgrades the boot ROMs.
If no options are specified, the user is prompted to confirm the reboot operation. For example:
ALA-1>admin# reboot
Are you sure you want to reboot (y/n)?
If the now option is specified, boot confirmation messages appear.
Parameters
CPMupgrade — Enables card firmware to be upgraded during chassis reboot. The 7210 SAS OS
and the boot.tim support functionality to perform automatic firmware upgrades on s. The
automatic upgrade must be enabled in the 7210 SAS OS Command Line Interface (CLI) when
rebooting the system.
When the upgrade keyword is specified, a chassis flag is set for the BOOT Loader (boot.tim)
and on the subsequent boot of the 7210 SAS OS on the chassis, any firmware images on s
requiring upgrading will be upgraded automatically.
If an 7210 SAS is rebooted with the admin reboot command (without the upgrade keyword),
the firmware images are left intact.
During any firmware upgrade, automatic or manual, it is imperative that during the upgrade
procedure:
• Power must NOT be switched off or interrupted.
• The system must NOT be reset.
• No cards are inserted or removed.
Any of the above conditions may render cards inoperable requiring a return of the card for
resolution.
now — Forces a reboot of the router immediately without an interactive confirmation.
auto-init — Specifies to reset the BOF and initiates a reboot.
save
Syntax
Context
Description
save [file-url] [detail] [index]
admin
This command saves the running configuration to a configuration file. For example:
A:ALA-1>admin# save ftp://test:[email protected]/./100.cfg
Saving configuration .........Completed.
By default, the running configuration is saved to the primary configuration file.
Parameters
file-url — The file URL location to save the configuration file.
Default
Page 272
The primary configuration file location.
7210 SAS D, E OS Basic System Configuration Guide
System Management
Values
file url:
local-url:
remote-url:
cflash-id:
local-url | remote-url: 255 chars max
[cflash-id/][file-path], 200 chars max, including the cflash-id
directory length, 99 chars max each
[{ftp://} login:pswd@remote-locn/][file-path]
remote-locn [ hostname | ipv4-address]
ipv4-address
a.b.c.d
255 chars max, directory length 99 chars max each
cf1:
detail — Saves both default and non-default configuration parameters.
index — Forces a save of the persistent index file regardless of the persistent status in the BOF file.
The index option can also be used to avoid an additional boot required while changing your
system to use the persistence indices.
enable-tech
Syntax
Context
Description
[no] enable-tech
admin
This command enables the shell and kernel commands.
NOTE: This command should only be used with authorized direction from the Alcatel-Lucent
Technical Assistance Center (TAC).
tech-support
Syntax
Context
Description
tech-support file-url
admin
This command creates a system core dump.
NOTE: This command should only be used with authorized direction from the Alcatel-Lucent
Technical Assistance Center (TAC).
file-url — The file URL location to save the binary file.
file url:
local-url:
local-url | remote-url: 255 chars max
[cflash-id/][file-path], 200 chars max, including the cflash-id
directory length, 99 chars max each
remote-url:
[{ftp://} login:pswd@remote-locn/][file-path]
remote-locn [ hostname | ipv4-address]
ipv4-address
a.b.c.d
255 chars max, directory length 99 chars max each
cflash-id:
cf1:
update-golden-bootstrap
7210 SAS D, E OS Basic System Configuration Guide
Page 273
System Administration Commands
Syntax
Context
Description
Default
Parameters
update-golden-bootstrap [file-url]
admin
This command updates the golden bootstrap image with the file-url , after validating it as a bootstrap
image for the 7210 SAS E platform.
cf1:/boot.tim
file-url — Specifies the file URL.
Values
Page 274
file-url:
local-url:
local-url:
cflash-id:
255 characters max
[cflash-id/][file-path]
cf1:
7210 SAS D, E OS Basic System Configuration Guide
System Management
System Alarm Contact Commands
Note: System Alarm Contact commands are not supported on 7210 SAS-D devices.
alarm-contact-input
Syntax
Context
Description
Default
Parameters
alarm-contact-input alarm-contact-input-id
config>system>alarm-contact-input
This command provides the context to configure one of four available alarm contact input pins.
None
alarm-contact-input-id — Identifies the alarm contact input pin.
Values
1—4
alarm-output-severity
Syntax
Context
Description
[[no] alarm-output-severity {critical | major | minor | none}
config>system>alarm-contact-input
This command allows the user to relay alarms from the alarm-contact input to the alarm-contact
output by associating an appropriate alarm-contact output with the alarm-contact input. The system
generates or clears the alarm-contact output when it triggers or clears the alarm for the associated
alarm-contact input.
If multiple alarm-contact input pins share an alarm-contact output, the system generates the alarmcontact output even if any one of the alarm-contact input is triggered and the system clears alarmcontact output only when all the alarm-contact input pins are cleared.
The severity parameter configured by the user determines the appropriate alarm-contact output to be
used for generation and clearing the alarm.
Note: The system relays the alarm-contact input to the appropriate alarm-contact output only if the
alarm-contact output is available on the platform.
Default
Parameters
Major
critical — A critical alarm output is generated or cleared.
major — A major alarm output is generated or cleared.
minor — A minor alarm output is generated or cleared.
none — No alarm output is generated or cleared.
7210 SAS D, E OS Basic System Configuration Guide
Page 275
System Alarm Contact Commands
clear-alarm-msg
Syntax
Context
Description
Default
Parameters
[no] clear-alarm-msg {alarm-msg-text}
config>system>alarm-contact-input alarm-contact-input-id
This command allows the user to configure a text message for use along with SNMP trap and Log
message that are sent when the system clears an alarm. The system generates a default message if the
message is not configured. The system does not generate a trap or log if no form of the command is
enabled.
None
alarm-msg-text — A printable character string, up to 160 characters in length.
description
Syntax
Context
Description
Default
description description-string
config>system>alarm-contact-input alarm-contact-input-id description
This command describes an alarm contact input pin. The description provides an indication of the
usage or attribute of the pin. It is stored in the CLI configuration file and helps the user in identifying
the purpose of the pin.
None
normal-state
Syntax
Context
Description
Default
Parameters
normal-state [open | closed]
config>system>alarm-contact-input alarm-contact-input-id
This command configures the normal state to be associated with the alarm-contact input. When the
system detects a transition from the normal state, an alarm is generated. The alarm is cleared when the
system detects a transition is back to the normal state.
closed
open — The normal-state is identified as ‘open’. When the system detects a transition to the ‘closed’
state, an alarm is generated. The alarm is cleared when the system detects a transition back to the
‘Open’ state.
closed-state — The normal-state is identified as ‘closed’. When the system detects a transition to
the‘open’ state, and alarm is generated. The alarm is cleared when the system detects a transition
back to the ‘closed’ state.
Page 276
7210 SAS D, E OS Basic System Configuration Guide
System Management
shutdown
Syntax
Context
Description
[no] shutdown
config>system>alarm-contact-input
This command stops tracking the state changes associated with the alarm contact input .The system
does not generate or clear the alarms for the alarm-contact input, but if an alarm is generated for the
alarm-contact-input, the system clears the alarm when the shutdown command is executed.
The no form of the command starts tracking the state changes associated with the alarm contact input.
Default
Shutdown
trigger-alarm-msg
Syntax
Context
Description
Default
Parameters
[no] trigger-alarm-msg {alarm-msg-text}
config>system>alarm-contact-input alarm-contact-input-id
This command allows the user to configure a text message for use along with SNMP trap and Log
message that are sent when the system generates an alarm. The system generates a default message if
the message is not configured. The system does not generate a trap or log if no form of the command
is enabled.
None
alarm-msg-text — A printable character string, up to 160 characters in length.
7210 SAS D, E OS Basic System Configuration Guide
Page 277
LLDP System Commands
LLDP System Commands
lldp
Syntax
Context
Description
lldp
config>system
This command enables the context to configure system-wide Link Layer Discovery Protocol
parameters.
message-fast-tx
Syntax
Context
message-fast-tx time
no message-fast-tx
config>system>lldp
Description
This command configures the duration of the fast transmission period.
Parameters
time — Specifies the fast transmission period in seconds.
Values
1 — 3600
Default
1
message-fast-tx-init
Syntax
Context
message-fast-tx-init count
no message-fast-tx-init
config>system>lldp
Description
This command configures the number of LLDPDUs to send during the fast transmission period.
Parameters
count — Specifies the number of LLDPDUs to send during the fast transmission period.
Page 278
Values
1—8
Default
4
7210 SAS D, E OS Basic System Configuration Guide
System Management
notification-interval
Syntax
Context
notification-interval time
no notification-interval
config>system>lldp
Description
This command configures the minimum time between change notifications.
Parameters
time — Specifies the minimum time, in seconds, between change notifications.
Values
5 — 3600
Default
5
reinit-delay
Syntax
Context
reinit-delay time
no reinit-delay
config>system>lldp
Description
This command configures the time before re-initializing LLDP on a port.
Parameters
time — Specifies the time, in seconds, before re-initializing LLDP on a port.
Values
1 — 10
Default
2
tx-credit-max
Syntax
tx-credit-max count
no tx-credit-max
Context
config>system>lldp
Description
This command configures the maximum consecutive LLDPDUs transmitted.
Parameters
count — Specifies the maximum consecutive LLDPDUs transmitted.
Values
1 — 100
Default
5
7210 SAS D, E OS Basic System Configuration Guide
Page 279
LLDP System Commands
tx-hold-multiplier
Syntax
Context
tx-hold-multiplier multiplier
no tx-hold-multiplier
config>system>lldp
Description
This command configures the multiplier of the tx-interval.
Parameters
multiplier — Specifies the multiplier of the tx-interval.
Values
2 — 10
Default
4
tx-interval
Syntax
tx-interval interval
no tx-interval
Context
config>system>lldp
Description
Parameters
Page 280
This command configures the LLDP transmit interval time.
interval — Specifies the LLDP transmit interval time.
Values
1 — 100
Default
5
7210 SAS D, E OS Basic System Configuration Guide
System Management
LLDP Ethernet Port Commands
lldp
Syntax
Context
Description
lldp
config>port>ethernet
This command enables the context to configure Link Layer Discovery Protocol (LLDP) parameters
on the specified port.
dest-mac
Syntax
Context
dest-mac {bridge-mac}
config>port>ethernet>lldp
Description
This command configures destination MAC address parameters.
Parameters
bridge-mac — Specifies destination bridge MAC type to use by LLDP.
Values
nearest-bridge — Specifies to use the nearest bridge.
nearest-non-tpmr — Specifies to use the nearest non-Two-Port MAC Relay
(TPMR) .
nearest-customer — Specifies to use the nearest customer.
admin-status
Syntax
Context
admin-status {rx | tx | tx-rx | disabled}
config>port>ethernet>lldp>dstmac
Description
This command specifies the administratively desired status of the local LLDP agent.
Parameters
rx — Specifies the LLDP agent will receive, but will not transmit LLDP frames on this port.
tx — Specifies that the LLDP agent will transmit LLDP frames on this port and will not store any
information about the remote systems connected.
tx-rx — Specifies that the LLDP agent will transmit and receive LLDP frames on this port.
disabled — Specifies that the LLDP agent will not transmit or receive LLDP frames on this port. If
there is remote systems information which is received on this port and stored in other tables,
before the port's admin status becomes disabled, then the information will naturally age out.
7210 SAS D, E OS Basic System Configuration Guide
Page 281
LLDP Ethernet Port Commands
notification
Syntax
Context
Description
[no] notification
config>port>ethernet>lldp>dstmac
This command enables LLDP notifications.
The no form of the command disables LLDP notifications.
tx-mgmt-address
Syntax
Context
Description
tx-mgmt-address [system]
no tx-mgmt-address
config>port>ethernet>lldp>dstmac
This command specifies which management address to transmit.
The no form of the command resets value to the default.
Default
Parameters
no tx-mgmt-address
system — Specifies to use the system IP address. Note that the system address will only be
transmitted once it has been configured if this parameter is specified
tx-tlvs
Syntax
Context
Description
tx-tlvs [port-desc] [sys-name] [sys-desc] [sys-cap]
no tx-tlvs
config>port>ethernet>lldp>dstmac
This command specifies which LLDP TLVs to transmit.
The no form of the command resets the value to the default.
Default
Parameters
no tx-tlvs
port-desc — Indicates that the LLDP agent should transmit port description TLVs.
sys-name — Indicates that the LLDP agent should transmit system name TLVs.
sys-desc — Indicates that the LLDP agent should transmit system description TLVs.
sys-cap — Indicates that the LLDP agent should transmit system capabilities TLVs.
Page 282
7210 SAS D, E OS Basic System Configuration Guide
System Management
Show Commands
SYSTEM COMMANDS
connections
Syntax
Context
connections [address ip-address [interface interface-name]] [port port-number] [detail]
show>system
Description
This command displays UDP and TCP connection information.
If no command line options are specified, a summary of the TCP and UDP connections displays.
Parameters
ip-address — Displays only the connection information for the specified IP address.
ipv4-address:
a.b.c.d (host bits must be 0)
port-number — Displays only the connection information for the specified port number.
Values
0 — 65535
detail — Appends TCP statistics to the display output.
Output
Standard Connection Output — The following table describes the system connections output
fields.
Label
Description
Proto
Displays the socket protocol, either TCP or UDP.
RecvQ
Displays the number of input packets received by the protocol.
TxmtQ
Displays the number of output packets sent by the application.
Local Address
Displays the local address of the socket. The socket port is separated
by a period.
Remote Address
Displays the remote address of the socket. The socket port is separated
by a period.
State
Listen — The protocol state is in the listen mode.
Established — The protocol state is established.
Sample Output
A:ALA-12# show system connections
7210 SAS D, E OS Basic System Configuration Guide
Page 283
System Commands
===============================================================================
Connections :
===============================================================================
Proto
RecvQ
TxmtQ Local Address
Remote Address
State
------------------------------------------------------------------------------TCP
0
0 0.0.0.0.21
0.0.0.0.0
LISTEN
TCP
0
0 0.0.0.0.23
0.0.0.0.0
LISTEN
TCP
0
0 0.0.0.0.179
0.0.0.0.0
LISTEN
TCP
0
0 10.0.0.xxx.51138
10.0.0.104.179
SYN_SENT
TCP
0
0 10.0.0.xxx.51139
10.0.0.91.179
SYN_SENT
TCP
0
0 10.10.10.xxx.646
0.0.0.0.0
LISTEN
TCP
0
0 10.10.10.xxx.646
10.10.10.104.49406
ESTABLISHED
TCP
0
0 11.1.0.1.51140
11.1.0.2.179
SYN_SENT
TCP
0
993 192.168.x.xxx.23
192.168.x.xx.xxxx
ESTABLISHED
UDP
0
0 0.0.0.0.123
0.0.0.0.0
--UDP
0
0 0.0.0.0.646
0.0.0.0.0
--UDP
0
0 0.0.0.0.17185
0.0.0.0.0
--UDP
0
0 10.10.10.xxx.646
0.0.0.0.0
--UDP
0
0 127.0.0.1.50130
127.0.0.1.17185
--------------------------------------------------------------------------------No. of Connections: 14
===============================================================================
A:ALA-12#
Sample Detailed Output
A:ALA-12# show system connections detail
------------------------------------------------------------------------------TCP Statistics
------------------------------------------------------------------------------packets sent
: 659635
data packets
: 338982 (7435146 bytes)
data packet retransmitted
: 73 (1368 bytes)
ack-only packets
: 320548 (140960 delayed)
URG only packet
: 0
window probe packet
: 0
window update packet
: 0
control packets
: 32
packets received
: 658893
acks
: 338738 for (7435123 bytes)
duplicate acks
: 23
ack for unsent data
: 0
packets received in-sequence
: 334705 (5568368 bytes)
completely duplicate packet
: 2 (36 bytes)
packet with some dup. data
: 0 (0 bytes)
out-of-order packets
: 20 (0 bytes)
packet of data after window
: 0 (0 bytes)
window probe
: 0
window update packet
: 3
packets received after close
: 0
discarded for bad checksum
: 0
discarded for bad header offset field
: 0
discarded because packet too short
: 0
connection request
: 4
connection accept
: 24
connections established (including accepts) : 27
Page 284
7210 SAS D, E OS Basic System Configuration Guide
System Management
connections closed
: 26 (including 2 drops)
embryonic connections dropped
: 0
segments updated rtt
: 338742 (of 338747 attempts)
retransmit timeouts
: 75
connections dropped by rexmit timeout
: 0
persist timeouts
: 0
keepalive timeouts
: 26
keepalive probes sent
: 0
connections dropped by keepalive
: 1
pcb cache lookups failed
: 0
===============================================================================
A:ALA-12#
cpu
Syntax
Context
cpu [sample-period seconds]
show>system
Description
This command displays CPU utilization per task over a sample period.
Parameters
sample-period seconds — The number of seconds over which to sample CPU task utilization.
Output
Default
1
Values
1—5
System CPU Output — The following table describes the system CPU output fields.
Table 20: Show System CPU Output Fields
Label
Description
CPU Utilization
The total amount of CPU time.
Name
The process or protocol name.
CPU Time (uSec)
The CPU time each process or protocol has used in the specified time.
CPU Usage
The sum of CPU usage of all the processes and protocols.
Capacity Usage
Displays the level the specified service is being utilized. When this
number hits 100%, this part of the system is busied out. There may be
extra CPU cycles still left for other processes, but this service is running at capacity.
This column does not reflect the true CPU utilization value; that data is
still available in the CPU Usage column. This column is the busiest
task in each group, where busiest is defined as either actually running
or blocked attempting to acquire a lock.
7210 SAS D, E OS Basic System Configuration Guide
Page 285
System Commands
Sample Output
*A:cses-E11# show system cpu sample-period 2
===============================================================================
CPU Utilization (Sample period: 2 seconds)
===============================================================================
Name
CPU Time
CPU Usage
Capacity
(uSec)
Usage
------------------------------------------------------------------------------BFD
10
~0.00%
~0.00%
Cards & Ports
8,332
0.41%
0.08%
IS-IS
1,213
0.06%
0.06%
ISA
2,496
0.12%
0.07%
LDP
0
0.00%
0.00%
Logging
32
~0.00%
~0.00%
MSDP
0
0.00%
0.00%
Management
5,969
0.29%
0.15%
OAM
907
0.04%
0.02%
OSPF
25
~0.00%
~0.00%
Redundancy
3,635
0.18%
0.13%
SIM
1,462
0.07%
0.04%
SNMP Daemon
0
0.00%
0.00%
Services
2,241
0.11%
0.05%
Stats
0
0.00%
0.00%
Subscriber Mgmt
2,129
0.10%
0.04%
System
8,802
0.43%
0.17%
Traffic Eng
0
0.00%
0.00%
WEB Redirect
125
~0.00%
~0.00%
------------------------------------------------------------------------------Total
2,014,761
100.00%
Idle
1,945,113
96.54%
Usage
69,648
3.45%
Busiest Core Utilization
69,648
3.45%
===============================================================================
*A:cses-E11#
cron
Syntax
Context
Description
cron
show>cron
This command enters the show CRON context.
action
Syntax
Context
Description
Page 286
action [action-name] [owner action-owner] run-history run-state
show>cron#
This command displays cron action parameters.
7210 SAS D, E OS Basic System Configuration Guide
System Management
Parameters
action action-name — Specifies the action name.
Values
maximum 32 characters
owner action-owner — Specifies the owner name.
Default
TiMOS CLI
run-history run-state — Specifies the state of the test to be run.
Values
Output
executing, initializing, terminated
The following table describes the show cron action output fields.
Label
Description
Action
Displays the name of the action.
Action owner
The name of the action owner.
Administrative
status
Enabled — Administrative status is enabled
Disabled — Administrative status is disabled
Script
The name of the script
Script owner
The name of the script owner.
Script source
location
Displays the location of scheduled script.
Max running
allowed
Displays the maximum number of allowed sessions.
Max completed run
histories
Displays the maximum number of sessions previously run.
Max lifetime
allowed
Displays the maximum amount of time the script may run.
Completed run
histories
Displays the number of completed sessions.
Executing run
histories
Displays the number of sessions in the process of executing.
Initializing run
histories
Displays the number of sessions ready to run/queued but not executed.
Max time run history saved
Displays the maximum amount of time to keep the results from a
script run.
Last change
Displays the system time a change was made to the configuration.
7210 SAS D, E OS Basic System Configuration Guide
Page 287
System Commands
Sample Output
*A:Redundancy# show cron action run-history terminated
===============================================================================
CRON Action Run History
===============================================================================
Action "test"
Owner "TiMOS CLI"
------------------------------------------------------------------------------Script Run #17
------------------------------------------------------------------------------Start time
: 2006/11/06 20:30:09
End time
: 2006/11/06 20:35:24
Elapsed time : 0d 00:05:15
Lifetime
: 0d 00:00:00
State
: terminated
Run exit code : noError
Result time
: 2006/11/06 20:35:24
Keep history : 0d 00:49:57
Error time
: never
Results file : ftp://*:*@192.168.15.18/home/testlab_bgp/cron/_20061106-203008.
out
Run exit
: Success
------------------------------------------------------------------------------Script Run #18
------------------------------------------------------------------------------Start time
: 2006/11/06 20:35:24
End time
: 2006/11/06 20:40:40
Elapsed time : 0d 00:05:16
Lifetime
: 0d 00:00:00
State
: terminated
Run exit code : noError
Result time
: 2006/11/06 20:40:40
Keep history : 0d 00:55:13
Error time
: never
Results file : ftp://*:*@192.168.15.18/home/testlab_bgp/cron/_20061106-203523.
out
Run exit
: Success
------------------------------------------------------------------------------*A:Redundancy#
*A:Redundancy# show cron action run-history executing
===============================================================================
CRON Action Run History
===============================================================================
Action "test"
Owner "TiMOS CLI"
------------------------------------------------------------------------------Script Run #20
------------------------------------------------------------------------------Start time
: 2006/11/06 20:46:00
End time
: never
Elapsed time : 0d 00:00:56
Lifetime
: 0d 00:59:04
State
: executing
Run exit code : noError
Result time
: never
Keep history : 0d 01:00:00
Error time
: never
Results file : ftp://*:*@192.168.15.18/home/testlab_bgp/cron/_20061106-204559.
out
===============================================================================
*A:Redundancy#
*A:Redundancy# show cron action run-history initializing
===============================================================================
CRON Action Run History
===============================================================================
Action "test"
Page 288
7210 SAS D, E OS Basic System Configuration Guide
System Management
Owner "TiMOS CLI"
------------------------------------------------------------------------------Script Run #21
------------------------------------------------------------------------------Start time
: never
End time
: never
Elapsed time : 0d 00:00:00
Lifetime
: 0d 01:00:00
State
: initializing
Run exit code : noError
Result time
: never
Keep history : 0d 01:00:00
Error time
: never
Results file : none
------------------------------------------------------------------------------Script Run #22
------------------------------------------------------------------------------Start time
: never
End time
: never
Elapsed time : 0d 00:00:00
Lifetime
: 0d 01:00:00
State
: initializing
Run exit code : noError
Result time
: never
Keep history : 0d 01:00:00
Error time
: never
Results file : none
------------------------------------------------------------------------------Script Run #23
------------------------------------------------------------------------------Start time
: never
End time
: never
Elapsed time : 0d 00:00:00
Lifetime
: 0d 01:00:00
State
: initializing
Run exit code : noError
Result time
: never
Keep history : 0d 01:00:00
Error time
: never
Results file : none
===============================================================================
*A:Redundancy#
schedule
Syntax
Context
schedule [schedule-name] [owner schedule-owner]
show>cron#
Description
This command displays cron schedule parameters.
Parameters
schedule-name — Displays information for the specified scheduler name.
owner schedule-owner — Displays information for the specified scheduler owner.
Output
The following table describes the show cron schedule output fields.
A:sim1>show>cron schedule test
Label
Description
Schedule name
Displays the schedule name.
Schedule owner
Displays the owner name of the action.
Description
Displays the schedule’s description.
7210 SAS D, E OS Basic System Configuration Guide
Page 289
System Commands
Label
Description (Continued)
Administrative
status
Enabled — The administrative status is enabled.
Disabled — Administratively disabled.
Operational status
Enabled — The operational status is enabled.
Disabled — Operationally disabled.
Action
Displays the action name
Action owner
Displays the name of action owner.
Script
Displays the name of the script.
Script owner
Displays the name of the script.
Script owner
Displays the name of the of script owner.
Script source
location
Displays the location of scheduled script.
Script results
location
Displays the location where the script results have been sent.
Schedule type
Periodic — Displays a schedule which ran at a given interval.
Calendar — Displays a schedule which ran based on a calendar.
Oneshot — Displays a schedule which ran one time only.
Page 290
Interval
Displays the interval between runs of an event.
Next scheduled run
Displays the time for the next scheduled run.
Weekday
Displays the configured weekday.
Month
Displays the configured month.
Day of Month
Displays the configured day of month.
Hour
Displays the configured hour.
Minute
Displays the configured minute.
Number of scheduled runs
Displays the number of scheduled sessions.
Last scheduled run
Displays the last scheduled session.
Number of scheduled failures
Displays the number of scheduled sessions that failed to execute.
Last scheduled
failure
Displays the last scheduled session that failed to execute.
7210 SAS D, E OS Basic System Configuration Guide
System Management
Label
Last failure time
Description (Continued)
Displays the system time of the last failure.
===============================================================================
CRON Schedule Information
===============================================================================
Schedule
: test
Schedule owner
: TiMOS CLI
Description
: none
Administrative status
: enabled
Operational status
: enabled
Action
: test
Action owner
: TiMOS CLI
Script
: test
Script Owner
: TiMOS CLI
Script source location
: ftp://*****:******@192.168.15.1/home/testlab_bgp
/cron/test1.cfg
Script results location
: ftp://*****:******@192.168.15.1/home/testlab_bgp
/cron/res
Schedule type
: periodic
Interval
: 0d 00:01:00 (60 seconds)
Next scheduled run
: 0d 00:00:42
Weekday
: tuesday
Month
: none
Day of month
: none
Hour
: none
Minute
: none
Number of schedule runs
: 10
Last schedule run
: 2008/01/01 17:20:52
Number of schedule failures : 0
Last schedule failure
: no error
Last failure time
: never
===============================================================================
A:sim1>show>cron
script
Syntax
Context
script [script-name] [owner script-owner]
show>cron#
Description
This command displays cron script parameters.
Parameters
schedule-name — Displays information for the specified script.
owner schedule-owner — Displays information for the specified script owner.
Output
The following table describes the show cron script output fields.
Label
Script
Description
Displays the name of the script.
7210 SAS D, E OS Basic System Configuration Guide
Page 291
System Commands
Label
Description (Continued)
Script owner
Displays the owner name of script.
Administrative
status
Enabled — Administrative status is enabled.
Disabled — Administratively abled.
Operational status
Enabled — Operational status is enabled.
Disabled — Operationally disabled.
Script source
location
Displays the location of scheduled script.
Last script error
Displays the system time of the last error.
Last change
Displays the system time of the last change.
Sample Output
A:sim1>show>cron# script
===============================================================================
CRON Script Information
===============================================================================
Script
: test
Owner name
: TiMOS CLI
Description
: asd
Administrative status
: enabled
Operational status
: enabled
Script source location
: ftp://*****:******@192.168.15.1/home/testlab_bgp
/cron/test1.cfg
Last script error
: none
Last change
: 2006/11/07 17:10:03
===============================================================================
A:sim1>show>cron#
information
Syntax
information
Context
show>system
Description
Page 292
This command displays general system information including basic system, SNMP server, last boot
and DNS client information.
7210 SAS D, E OS Basic System Configuration Guide
System Management
Output
System Information Output — The following table describes the system information output
fields.
Label
Description
System Name
The configured system name.
System Contact
A text string that describes the system contact information.
System Location
A text string that describes the system location.
System Coordinates
A text string that describes the system coordinates.
System Up Time
The time since the last boot.
SNMP Port
The port number used by this node to receive SNMP request messages
and to send replies.
SNMP Engine ID
The SNMP engineID to uniquely identify the SNMPv3 node.
SNMP Max Message
Size
The maximum SNMP packet size generated by this node.
SNMP Admin State
Enabled — SNMP is administratively enabled and running.
Disabled — SNMP is administratively shutdown and not running.
SNMP Oper State
Enabled — SNMP is operationally enabled.
Disabled — SNMP is operationally disabled.
SNMP Index Boot
Status
Persistent — System indexes are saved between reboots.
Not Persistent — System indexes are not saved between
reboots.
Telnet/SSH/FTP
Admin
Displays the administrative state of the Telnet, SSH, and FTP sessions.
Telnet/SSH/FTP
Oper
Displays the operational state of the Telnet, SSH, and FTP sessions.
BOF Source
The location of the BOF.
Image Source
Primary — Indicates that the directory location for runtime image
file was loaded from the primary source.
Secondary — Indicates that the directory location for runtime
image file was loaded from the secondary source.
Tertiary — Indicates that the directory location for runtime image
file was loaded from the tertiary source.
7210 SAS D, E OS Basic System Configuration Guide
Page 293
System Commands
Label
Page 294
Description (Continued)
Config Source
Primary — Indicates that the directory location for configuration
file was loaded from the primary source.
Secondary — Indicates that the directory location for configuration
file was loaded from the secondary source.
Tertiary — Indicates that the directory location for configuration
file was loaded from the tertiary source.
Last Booted Config
File
The URL and filename of the last loaded configuration file.
Last Boot Cfg Version
The date and time of the last boot.
Last Boot Config
Header
Displays header information such as image version, date built, date
generated.
Last Boot Index
Version
The version of the persistence index file read when this card was last
rebooted.
Last Boot Index
Header
The header of the persistence index file read when this card was last
rebooted.
Last Saved Config
The location and filename of the last saved configuration file.
Time Last Saved
The date and time of the last time configuration file was saved.
Changes Since Last
Save
Yes — There are unsaved configuration file changes.
No — There are no unsaved configuration file changes.
Time Last Modified
The date and time of the last modification.
Max Cfg/BOF Backup
Rev
The maximum number of backup revisions maintained for a configuration file. This value also applies to the number of revisions maintained
for the BOF file.
Cfg-OK Script
URL — The location and name of the CLI script file executed following successful completion of the boot-up configuration file execution.
Cfg-OK Script Status
Successful/Failed. The results from the execution of the CLI
script file specified in the Cfg-OK Script location.
Not used — No CLI script file was executed.
Cfg-Fail Script
URL — The location and name of the CLI script file executed following a failed boot-up configuration file execution.
Not used — No CLI script file was executed.
Cfg-Fail Script
Status
Successful/Failed — The results from the execution of the
CLI script file specified in the Cfg-Fail Script location.
Not used — No CLI script file was executed.
7210 SAS D, E OS Basic System Configuration Guide
System Management
Label
Description (Continued)
DNS Server
The IP address of the DNS server.
DNS Domain
The DNS domain name of the node.
BOF Static Routes
To — The static route destination.
Next Hop — The next hop IP address used to reach the destination.
Metric — Displays the priority of this static route versus other static
routes.
None — No static routes are configured.
memory-pools
Syntax
Context
Description
Output
memory-pools
show>system
This command displays system memory status.
Memory Pools Output — The following table describes memory pool output fields.
Table 21: Show Memory Pool Output Fields
Label
Description
Name
The name of the system or process.
Max Allowed
Integer — The maximum allocated memory size.
No Limit — No size limit.
Current Size
The current size of the memory pool.
Max So Far
The largest amount of memory pool used.
In Use
The current amount of the memory pool currently in use.
Current Total Size
The sum of the Current Size column.
Total In Use
The sum of the In Use column.
Available Memory
The amount of available memory.
Sample Output
A:ALA-1# show system memory-pools
===============================================================================
Memory Pools
===============================================================================
Name
Max Allowed
Current Size
Max So Far
In Use
7210 SAS D, E OS Basic System Configuration Guide
Page 295
System Commands
------------------------------------------------------------------------------System
No limit
24,117,248
24,117,248
16,974,832
Icc
8,388,608
1,048,576
1,048,576
85,200
RTM/Policies
No limit
5,242,912
5,242,912
3,944,104
OSPF
No limit
3,145,728
3,145,728
2,617,384
MPLS/RSVP
No limit
9,769,480
9,769,480
8,173,760
LDP
No limit
0
0
0
IS-IS
No limit
0
0
0
RIP
No limit
0
0
0
VRRP
No limit
1,048,576
1,048,576
96
Services
No limit
2,097,152
2,097,152
1,589,824
IOM
No limit
205,226,800
205,226,800
202,962,744
SIM
No limit
1,048,576
1,048,576
392
IGMP
No limit
0
0
0
MMPI
No limit
0
0
0
MFIB
No limit
0
0
0
PIP
No limit
79,943,024
79,943,024
78,895,248
MBUF
67,108,864
5,837,328
5,837,328
4,834,280
------------------------------------------------------------------------------Current Total Size :
343,495,200 bytes
Total In Use
:
324,492,768 bytes
Available Memory
:
640,178,652 bytes
===============================================================================
A:ALA-1#
ntp
Syntax
Context
Description
Output
ntp
show>system
This command displays NTP protocol configuration and state.
Show NTP Output — The following table describes NTP output fields.
Label
Enabled
Description
yes
no
Admin Status
yes
no
— NTP is disabled.
— Administrative state is enabled.
— Administrative state is disabled.
NTP Server
Displays NTP server state of this node.
Stratum
Displays stratum level of this node.
Oper Status
yes
no
Auth Check
Page 296
— NTP is enabled.
— The operational state is enabled.
— The operational state is disabled.
Displays the authentication requirement
7210 SAS D, E OS Basic System Configuration Guide
System Management
Label
Description (Continued)
System Ref. ID
IP address of this node or a 4-character ASCII code showing the state.
Auth Error
Displays the number of authentication errors.
Auth Errors
Ignored
Displays the number of authentication errors ignored.
Auth key ID Errors
Displays the number of key identification errors .
Auth Key Type
Errors
Displays the number of authentication key type errors.
Reject
The peer is rejected and will not be used for synchronization. Rejection
reasons could be the peer is unreachable, the peer is synchronized to
this local server so synchronizing with it would create a sync loop, or
the synchronization distance is too large. This is the normal startup
state.
Invalid
The peer is not maintaining an accurate clock. This peer will not be
used for synchronization.
Excess
The peer's synchronization distance is greater than ten other peers.
This peer will not be used for synchronization.
Outlyer
The peer is discarded as an outlyer. This peer will not be used for synchronization.
Candidate
The peer is accepted as a possible source of synchronization.
Selected
The peer is an acceptable source of synchronization, but its synchronization distance is greater than six other peers.
Chosen
The peer is chosen as the source of synchronization.
ChosenPPS
The peer is chosen as the source of synchronization, but the actual synchronization is occurring from a pulse-per-second (PPS) signal.
Remote
The IP address of the remote NTP server or peer with which this local
host is exchanging NTP packets.
Reference ID
When stratum is between 0 and 15 this field shows the IP address of
the remote NTP server or peer with which the remote is exchanging
NTP packets. For reference clocks, this field shows the identification
assigned to the clock, such as, “.GPS.” For an NTP server or peer, if
the client has not yet synchronized to a server/peer, the status cannot be
determined and displays the following codes:
7210 SAS D, E OS Basic System Configuration Guide
Page 297
System Commands
Label
Description (Continued)
Peer Codes:
ACST — The association belongs to any cast server.
AUTH — Server authentication failed. Please wait while the association is restarted.
AUTO — Autokey sequence failed. Please wait while the association
is restarted.
BCST — The association belongs to a broadcast server.
CRPT — Cryptographic authentication or identification failed. The
details should be in the system log file or the cryptostats statistics file,
if configured. No further messages will be sent to the server.
DENY — Access denied by remote server. No further messages will
be sent to the server.
DROP — Lost peer in symmetric mode. Please wait while the association is restarted.
RSTR — Access denied due to local policy. No further messages will
be sent to the server.
INIT — The association has not yet synchronized for the first time.
MCST — The association belongs to a manycast server.
NKEY — No key found. Either the key was never installed or is not
trusted.
RATE — Rate exceeded. The server has temporarily denied access
because the client exceeded the rate threshold.
RMOT — The association from a remote host running ntpdc has had
unauthorized attempted access.
STEP — A step change in system time has occurred, but the association has not yet resynchronized.
System Codes
INIT — The system clock has not yet synchronized for the first time.
STEP — A step change in system time has occurred, but the system
clock has not yet resynchronized.
St
Stratum level of this node.
Auth
yes — Authentication is enabled.
no — Authentication is disabled.
Poll
Polling interval in seconds.
R
Yes — The NTP peer or server has been reached at least once in the
last 8 polls.
No — The NTP peer or server has not been reached at least once in
the last 8 polls.
Offset
Page 298
The time between the local and remote UTC time, in milliseconds.
7210 SAS D, E OS Basic System Configuration Guide
System Management
Sample Output
A:pc-40>config>system>time>ntp# show system ntp
===============================================================================
NTP Status
===============================================================================
Enabled
: Yes
Stratum
: 3
Admin Status
: up
Oper Status
: up
Server enabled
: No
Server keyId
: none
System Ref Id
: 192.168.15.221
Auth Check
: Yes
===============================================================================
A:pc-40>config>system>time>ntp# show system ntp all
===============================================================================
NTP Status
===============================================================================
Enabled
: Yes
Stratum
: 3
Admin Status
: up
Oper Status
: up
Server enabled
: No
Server keyId
: none
System Ref Id
: 192.168.15.221
Auth Check
: Yes
===============================================================================
NTP Active Associations
===============================================================================
State
Remote
Reference ID
St Type
Auth Poll R Offset
------------------------------------------------------------------------------reject
192.168.15.221 192.168.14.50
2
srvr
none 64
y 0.901
chosen
192.168.15.221 192.168.14.50
2
mclnt none 64
y 1.101
===============================================================================
A:pc-40>config>system>time>ntp#
*A:pc-4.0# show system ntp detail
===============================================================================
NTP Status
===============================================================================
Enabled
: Yes
Stratum
: 3
Admin Status
: up
Oper Status
: up
Server enabled
: No
Server keyId
: none
System Ref Id
: 10.135.16.130
Auth Check
: Yes
Auth Errors
: 1
Auth Errors Ignored : 0
Auth Key Id Errors : 1
Auth Key Type Errors : 0
===============================================================================
===============================================================================
NTP Configured Broadcast Interfaces
===============================================================================
vRouter
Interface
Address
Type
Auth
Poll
------------------------------------------------------------------------------Base
new
Host-ones
bcast
no
off
Base
direct
Host-ones
bclnt
no
n/a
===============================================================================
*A:pc-4.0#
*A:pc-4.0# show system ntp detail all
===============================================================================
NTP Status
===============================================================================
Enabled
: Yes
Stratum
: 3
Admin Status
: up
Oper Status
: up
7210 SAS D, E OS Basic System Configuration Guide
Page 299
System Commands
Server enabled
: No
Server keyId
: none
System Ref Id
: 10.135.16.130
Auth Check
: Yes
Auth Errors
: 0
Auth Errors Ignored : 0
Auth Key Id Errors : 0
Auth Key Type Errors : 0
===============================================================================
===============================================================================
NTP Configured Broadcast Interfaces
===============================================================================
vRouter
Interface
Address
Type
Auth
Poll
------------------------------------------------------------------------------Base
new
Host-ones
bcast
no
off
Base
direct
Host-ones
bclnt
no
n/a
===============================================================================
===============================================================================
NTP Active Associations
===============================================================================
State
Remote
Reference ID
St Type A Poll Reach
Offset(ms)
------------------------------------------------------------------------------candidate 21.0.0.1
10.135.16.130
3 actpr y 64
YYYY.YY. 14.440
chosen
10.135.16.130
127.127.1.0
2 srvr - 256 .Y.YYYYY 24.364
reject
10.135.16.130
127.127.1.0
2 bclnt - 64
.......Y 27.576
===============================================================================
*A:pc-4.0#
sntp
Syntax
Context
Description
Output
sntp
show>system
This command displays SNTP protocol configuration and state.
Show SNTP Output — The following table describes SNTP output fields.
Table 22: Show System SNTP Output Fields
Label
Description
SNTP Server
The SNTP server address for SNTP unicast client mode.
Version
The SNTP version number, expressed as an integer.
Preference
Normal — When more than one time server is configured, one
server can be configured to have preference over another.
Preferred — Indicates that this server has preference over another.
Interval
The frequency, in seconds, that the server is queried.
*A:pc-4.0# show system sntp
===============================================================================
SNTP Status
===============================================================================
Admin Status : up
Oper Status : up
Mode : broadcast
Page 300
7210 SAS D, E OS Basic System Configuration Guide
System Management
===============================================================================
===============================================================================
SNTP Servers
===============================================================================
SNTP Server
Version
Preference
Interval
------------------------------------------------------------------------------10.135.16.90
3
Preferred
64
------------------------------------------------------------------------------No. of SNTP Servers: 1
===============================================================================
*A:pc-4.0#
thresholds
Syntax
Context
Description
Output
thresholds
show>system
This command display system monitoring thresholds.
Thresholds Output — following table describes system threshold output fields.
Label
Description
Variable
Displays the variable OID.
Alarm Id
Displays the numerical identifier for the alarm.
Last Value
Displays the last threshold value.
Rising Event Id
Displays the identifier of the RMON rising event.
Threshold
Displays the identifier of the RMON rising threshold.
Falling Event Id
Displays the identifier of the RMON falling event.
Threshold
Displays the identifier of the RMON falling threshold.
Sample Interval
Displays the polling interval, in seconds, over which the data is
sampled and compared with the rising and falling thresholds.
Sample Type
Displays the method of sampling the selected variable and calculating
the value to be compared against the thresholds.
Startup Alarm
Displays the alarm that may be sent when this alarm is first created.
Owner
Displays the owner of this alarm.
Description
Displays the event cause.
Event Id
Displays the identifier of the threshold event.
Last Sent
Displays the date and time the alarm was sent.
7210 SAS D, E OS Basic System Configuration Guide
Page 301
System Commands
Label
Description (Continued)
Action Type
log — An entry is made in the RMON-MIB log table for each event
occurrence. This does not create a TiMOS logger entry. The RMONMIB log table entries can be viewed using the show>system>thresholds CLI command.
trap — A TiMOS logger event is generated. The TiMOS logger utility
then distributes the notification of this event to its configured log destinations which may be CONSOLE, telnet session, memory log, cflash
file, syslog, or SNMP trap destinations logs.
both — Both a entry in the RMON-MIB logTable and a TiMOS logger
event are generated.
none — No action is taken
Owner
Displays the owner of the event.
Sample Output
A:ALA-48# show system thresholds
================================================================
Threshold Alarms
================================================================
Variable: tmnxCpmFlashUsed.1.11.1
Alarm Id
: 1
Last Value : 835
Rising Event Id : 1
Threshold : 5000
Falling Event Id : 2
Threshold : 2500
Sample Interval : 2147483* SampleType : absolute
Startup Alarm
: either
Owner
: TiMOS CLI
Variable: tmnxCpmFlashUsed.1.11.1
Alarm Id
: 2
Last Value : 835
Rising Event Id : 3
Threshold : 10000
Falling Event Id : 4
Threshold : 5000
Sample Interval : 2147483* SampleType : absolute
Startup Alarm
: rising
Owner
: TiMOS CLI
Variable: sgiMemoryUsed.0
Alarm Id
: 3
Last Value : 42841056
Rising Event Id : 5
Threshold : 4000
Falling Event Id : 6
Threshold : 2000
Sample Interval : 2147836 SampleType : absolute
Startup Alarm
: either
Owner
: TiMOS CLI
================================================================
* indicates that the corresponding row element may have been truncated.
================================================================
Threshold Events
================================================================
Description: TiMOS CLI - cflash capacity alarm rising event
Event Id
: 1
Last Sent : 10/31/2006 08:47:59
Action Type
: both
Owner
: TiMOS CLI
Description: TiMOS CLI - cflash capacity alarm falling event
Event Id
: 2
Last Sent : 10/31/2006 08:48:00
Action Type
: both
Owner
: TiMOS CLI
Description: TiMOS CLI - cflash capacity warning rising event
Page 302
7210 SAS D, E OS Basic System Configuration Guide
System Management
Event Id
: 3
Last Sent : 10/31/2006 08:47:59
Action Type
: both
Owner
: TiMOS CLI
Description: TiMOS CLI - cflash capacity warning falling event
Event Id
: 4
Last Sent : 10/31/2006 08:47:59
Action Type
: both
Owner
: TiMOS CLI
Description: TiMOS CLI - memory usage alarm rising event
Event Id
: 5
Last Sent : 10/31/2006 08:48:00
Action Type
: both
Owner
: TiMOS CLI
Description: TiMOS CLI - memory usage alarm falling event
Event Id
: 6
Last Sent : 10/31/2006 08:47:59
Action Type
: both
Owner
: TiMOS CLI
================================================================
Threshold Events Log
================================================================
Description
: TiMOS CLI - cflash capacity alarm falling eve
nt : value=835, <=2500 : alarm-index 1, event
-index 2 alarm-variable OID tmnxCpmFlashUsed.
1.11.1
Event Id
: 2
Time Sent : 10/31/2006 08:48:00
Description
: TiMOS CLI - memory usage alarm rising event :
value=42841056, >=4000 : alarm-index 3, even
t-index 5 alarm-variable OID sgiMemoryUsed.0
Event Id
: 5
Time Sent : 10/31/2006 08:48:00
================================================================
A:ALA-48#
7210 SAS D, E OS Basic System Configuration Guide
Page 303
System Commands
time
Syntax
Context
Description
Output
time
show>system
This command displays the system time and zone configuration parameters.
System Time Output — The following table describes system time output fields.
Table 23: Show System Time Output Fields
Label
Description
Date & Time
The system date and time using the current time zone.
DST Active
Yes — Daylight Savings Time is currently in effect.
No — Daylight Savings Time is not currently in effect.
Zone
The zone names for the current zone, the non-DST zone, and the DST
zone if configured.
Zone type
Non-standard — The zone is user-defined.
Standard — The zone is system defined.
Offset from UTC
The number of hours and minutes added to universal time for the zone,
including the DST offset for a DST zone
Offset from NonDST
The number of hours (always 0) and minutes (0—60) added to the time
at the beginning of Daylight Saving Time and subtracted at the end
Daylight Saving Time.
Starts
The date and time Daylight Saving Time begins.
Ends
The date and time Daylight Saving Time ends.
Sample Output
A:ALA-1# show system time
===============================================================================
Date & Time
===============================================================================
Current Date & Time : 2006/05/05 23:03:13
DST Active
: yes
Current Zone
: PDT
Offset from UTC
: -7:00
------------------------------------------------------------------------------Non-DST Zone
: PST
Offset from UTC
: -8:00
Zone type
: standard
------------------------------------------------------------------------------DST Zone
: PDT
Offset from Non-DST
: 0:60
Starts
: first sunday in april 02:00
Page 304
7210 SAS D, E OS Basic System Configuration Guide
System Management
Ends
: last sunday in october 02:00
============================================================================
A:ALA-1#
A:ALA-1# show system time (with no DST zone configured)
===============================================================================
Date & Time
===============================================================================
Current Date & Time : 2006/05/12 11:12:05
DST Active
:
no
Current Zone
: APA
Offset from UTC : -8:00
------------------------------------------------------------------------------Non-DST Zone
: APA
Offset from UTC : -8:00
Zone Type
: non-standard
------------------------------------------------------------------------------No DST zone configured
===============================================================================
A:ALA-1#
time
Syntax
time
Context
show
Description
This command displays the current day, date, time and time zone.
The time is displayed either in the local time zone or in UTC depending on the setting of the root level
time-display command for the console session.
Output
Sample Output
A:ALA-49# show time
Tue Oct 31 12:17:15 GMT 2006
7210 SAS D, E OS Basic System Configuration Guide
Page 305
System Commands
tod-suite
Syntax
Context
Description
Output
tod-suite [detail]
tod-suite associations
tod-suite failed-associations
show>cron
This command displays information on the configured time-of-day suite.
CRON TOD Suite Output — The following table describes TOD suite output fields:
Table 24: Show System tod-suite Output Fields
Label
Description
Associations
Shows which SAPs this tod-suite is associated with.
failed-associations
Shows the SAPs or Multiservice sites where the TOD Suite could not
be applied successfully.
Detail
Shows the details of this tod-suite.
Sample Output
A:kerckhot_4# show cron tod-suite suite_sixteen detail
===============================================================================
Cron tod-suite details
===============================================================================
Name
: suite_sixteen
Type / Id
Time-range
Prio State
------------------------------------------------------------------------------Ingress Qos Policy
1160
day
5
Inact
1190
night
6
Activ
Ingress Scheduler Policy
SchedPolCust1_Day
day
5
Inact
SchedPolCust1_Night
night
6
Activ
Egress Qos Policy
1160
day
5
Inact
1190
night
6
Activ
Egress Scheduler Policy
SchedPolCust1Egress_Day
day
5
Inact
===============================================================================
A:kerckhot_4#
The following example shows output for TOD suite associations.
A:kerckhot_4# show cron tod-suite suite_sixteen associations
===============================================================================
Cron tod-suite associations for suite suite_sixteen
===============================================================================
Service associations
Page 306
7210 SAS D, E OS Basic System Configuration Guide
System Management
------------------------------------------------------------------------------Service Id : 1
Type
: VPLS
SAP 1/1/1:1
SAP 1/1/1:2
SAP 1/1/1:3
SAP 1/1/1:4
SAP 1/1/1:5
SAP 1/1/1:6
SAP 1/1/1:20
------------------------------------------------------------------------------Number of SAP's : 7
Customer Multi-Service Site associations
------------------------------------------------------------------------------Multi Service Site: mss_1_1
------------------------------------------------------------------------------Number of MSS's: 1
===============================================================================
A:kerckhot_4#
The following example shows output for TOD suite failed-associations.
A:kerckhot_4# show cron tod-suite suite_sixteen failed-associations
===============================================================================
Cron tod-suite associations failed
===============================================================================
tod-suite suite_sixteen : failed association for SAP
------------------------------------------------------------------------------Service Id : 1
Type
: VPLS
SAP 1/1/1:2
SAP 1/1/1:3
SAP 1/1/1:4
SAP 1/1/1:5
SAP 1/1/1:6
SAP 1/1/1:20
------------------------------------------------------------------------------tod-suite suite_sixteen : failed association for Customer MSS
------------------------------------------------------------------------------None
------------------------------------------------------------------------------Number of tod-suites failed/total : 1/1
===============================================================================
A:kerckhot_4#
Zooming in on one of the failed SAPs, the assignments of QoS and scheduler policies are shown as
not as intended:
A:kerckhot_4# show service id 1 sap 1/1/1:2
===============================================================================
Service Access Points(SAP)
===============================================================================
Service Id
: 1
SAP
: 1/1/1:2
Encap
: q-tag
Dot1Q Ethertype
: 0x8100
QinQ Ethertype
: 0x8100
Admin State
: Up
Oper State
: Up
Flags
: None
Last Status Change : 10/05/2006 18:11:34
Last Mgmt Change
: 10/05/2006 22:27:48
Max Nbr of MAC Addr: No Limit
Total MAC Addr
: 0
7210 SAS D, E OS Basic System Configuration Guide
Page 307
System Commands
Learned MAC Addr
:
Admin MTU
:
Ingress qos-policy :
Intend Ing qos-pol*:
Shared Q plcy
:
Ingr IP Fltr-Id
:
Ingr Mac Fltr-Id
:
tod-suite
:
Egr Agg Rate Limit :
ARP Reply Agent
:
Mac Learning
:
Mac Aging
:
L2PT Termination
:
0
1518
1130
1190
n/a
n/a
n/a
suite_sixteen
max
Unknown
Enabled
Enabled
Disabled
Static MAC Addr
:
Oper MTU
:
Egress qos-policy :
Intend Egr qos-po*:
Multipoint shared :
Egr IP Fltr-Id
:
Egr Mac Fltr-Id
:
qinq-pbit-marking :
0
1518
1130
1190
Disabled
n/a
n/a
both
Host Conn Verify :
Discard Unkwn Srce:
Mac Pinning
:
BPDU Translation :
Disabled
Disabled
Disabled
Disabled
Multi Svc Site
: None
I. Sched Pol
: SchedPolCust1
Intend I Sched Pol : SchedPolCust1_Night
E. Sched Pol
: SchedPolCust1Egress
Intend E Sched Pol : SchedPolCust1Egress_Night
Acct. Pol
: None
Collect Stats
: Disabled
Anti Spoofing
: None
Nbr Static Hosts : 0
===============================================================================
A:kerckhot_4#
If a time-range is specified for a filter entry, use the show filter command to view
results:
A:kerckhot_4# show filter ip 10
===============================================================================
IP Filter
===============================================================================
Filter Id
: 10
Applied
: No
Scope
: Template
Def. Action
: Drop
Entries
: 2
------------------------------------------------------------------------------Filter Match Criteria : IP
------------------------------------------------------------------------------Entry
: 1010
time-range
: day
Cur. Status
: Inactive
Log Id
: n/a
Src. IP
: 0.0.0.0/0
Src. Port
: None
Dest. IP
: 10.10.100.1/24
Dest. Port
: None
Protocol
: Undefined
Dscp
: Undefined
ICMP Type
: Undefined
ICMP Code
: Undefined
Fragment
: Off
Option-present : Off
Sampling
: Off
Int. Sampling : On
IP-Option
: 0/0
Multiple Option: Off
TCP-syn
: Off
TCP-ack
: Off
Match action : Forward
Next Hop
: 138.203.228.28
Ing. Matches : 0
Egr. Matches
: 0
Entry
: 1020
time-range
: night
Cur. Status
: Active
Log Id
: n/a
Src. IP
: 0.0.0.0/0
Src. Port
: None
Dest. IP
: 10.10.1.1/16
Dest. Port
: None
Protocol
: Undefined
Dscp
: Undefined
ICMP Type
: Undefined
ICMP Code
: Undefined
Fragment
: Off
Option-present : Off
Sampling
: Off
Int. Sampling : On
Page 308
7210 SAS D, E OS Basic System Configuration Guide
System Management
IP-Option
: 0/0
Multiple Option: Off
TCP-syn
: Off
TCP-ack
: Off
Match action : Forward
Next Hop
: 172.22.184.101
Ing. Matches : 0
Egr. Matches
: 0
===============================================================================
A:kerckhot_4#
If a filter is referred to in a TOD Suite assignment, use the show filter associations command to view
the output:
A:kerckhot_4# show filter ip 160 associations
===============================================================================
IP Filter
===============================================================================
Filter Id
: 160
Applied
: No
Scope
: Template
Def. Action
: Drop
Entries
: 0
------------------------------------------------------------------------------Filter Association : IP
------------------------------------------------------------------------------Tod-suite "english_suite"
- ingress, time-range "day" (priority 5)
===============================================================================
A:kerckhot_4#
time-range
Syntax
Context
Description
Output
time-range name associations [detail]
show>cron
This command displays information on the configured time ranges.
Time Range Output — The following table displays system time range output fields:
Table 25: Show System Time-range Output Fields
Label
Description
Associations
Shows the time-range as it is associated with the TOD suites and ACL
entries as well as the SAPs using them.
Detail
Shows the details of this time-range.
Sample Output
The following example shows time-range detail output.
7210 SAS D, E OS Basic System Configuration Guide
Page 309
System Commands
A:ala# show cron time-range time-range2 detail
===============================================================================
Cron time-range
===============================================================================
Name
: time-range1
Periodic
: Start * * * * End * * * *
Absolute
: Start * * * * End * * * *
The following example shows output for time-range associations with previously created IP and
MAC filters.
A:ala# show cron time-range day associations
===============================================================================
Cron time-range associations
===============================================================================
Name
: day
State : Inactive
------------------------------------------------------------------------------IP Filter associations
------------------------------------------------------------------------------IP filter Id : 10, entry 1010
------------------------------------------------------------------------------MAC Filter associations
------------------------------------------------------------------------------None
------------------------------------------------------------------------------Tod-suite associations
------------------------------------------------------------------------------Tod-suite : suite_sixteen, for Ingress Qos Policy "1160"
Tod-suite : suite_sixteen, for Ingress Scheduler Policy "SchedPolCust1_Day"
Tod-suite : suite_sixteen, for Egress Qos Policy "1160"
Tod-suite : suite_sixteen, for Egress Scheduler Policy "SchedPolCust1Egress_Day
===============================================================================
uptime
Syntax
Context
Description
Output
uptime
show
This command displays the time since the system started.
Uptime Output — The following table describes uptime output fields.
Table 26: System Timing Output Fields
Label
Description
Displays the length of time the system has been up in days,
hr:min:sec format.
System Up Time
Sample Output
A:ALA-1# show uptime
System Up Time
Page 310
: 11 days, 18:32:02.22 (hr:min:sec)
7210 SAS D, E OS Basic System Configuration Guide
System Management
A:ALA-1#
chassis
NOTE: 'environment' option is supported only on 7210 SAS-E
Syntax
Context
chassis [environment] [power-supply]
show
Description
This command displays general chassis status information.
Parameters
environment — Displays chassis environmental status information.
Default
Display all chassis information.
power-supply — Displays chassis power supply status information.
Default
Output
Display all chassis information.
Chassis Output — The following table describes chassis output fields.
Label
Description
Name
The system name for the router.
Type
The router series model number.
Location
The system location for the device.
Coordinates
A user-configurable string that indicates the Global Positioning System
(GPS) coordinates for the location of the chassis.
For example:
N 45 58 23, W 34 56 12
N37 37' 00 latitude, W122 22' 00 longitude
N36*39.246' W121*40.121'
CLLI Code
The Common Language Location Identifier (CLLI) that uniquely identifies the geographic location of places and certain functional categories of equipment unique to the telecommunications industry.
Number of slots
The number of slots in this chassis that are available for plug-in cards.
The total number includes slots.
Number of ports
The total number of ports currently installed in this chassis.
Critical LED
state
The current state of the Critical LED in this chassis.
Major LED state
The current state of the Major LED in this chassis.
Minor LED state
The current state of the Minor LED in this chassis.
7210 SAS D, E OS Basic System Configuration Guide
Page 311
System Commands
Label
Description (Continued)
Base MAC address
The base chassis Ethernet MAC address.
Part number
The part number.
CLEI code
The code used to identify the router.
Serial number
The part number. Not user modifiable.
Manufacture date
The chassis manufacture date. Not user modifiable.
Manufacturing
string
Factory-inputted manufacturing text string. Not user modifiable.
Time of last
boot
The date and time the most recent boot occurred.
Current alarm
state
Displays the alarm conditions for the specific board.
Number of fan
trays
The total number of fan trays installed in this chassis.
Number of fans
The total number of fans installed in this chassis.
Operational status
Current status of the fan tray.
Fan speed
Half speed — The fans are operating at half speed.
Full speed — The fans are operating at full speed.
Number of power
supplies
The number of power supplies installed in the chassis.
Power supply
number
The ID for each power supply installed in the chassis.
AC power
Within range — AC voltage is within range.
Out of range — AC voltage is out of range.
DC power
Within range — DC voltage is within range.
Out of range — DC voltage is out of range.
Over temp
Within range — The current temperature is within the acceptable
range.
Out of range — The current temperature is above the acceptable
range.
Status
Up/Present — The specified power supply is up.
Down — The specified power supply is down.
Page 312
7210 SAS D, E OS Basic System Configuration Guide
System Management
Sample Output
Note:This CLI output is obtained only if the hardware supports "DC source failure detection".
A:7210-SAS-E> show chassis
===============================================================================
Chassis Information
===============================================================================
Name
: STU2597
Type
: 7210 SAS-E-1
Location
:
Coordinates
:
CLLI code
:
Number of slots
: 2
Number of ports
: 24
Critical LED state
: Red
Major LED state
: Off
Minor LED state
: Off
Over Temperature state
: OK
Base MAC address
: 00:25:ba:04:b9:bc
Hardware Data
Part number
CLEI code
Serial number
Manufacture date
Manufacturing string
Manufacturing deviations
Time of last boot
Current alarm state
:
:
:
:
:
:
:
:
3HE04410ABAC01
IPMK310JRA
NS1026C0341
06292010
2010/11/09 16:12:40
alarm active
------------------------------------------------------------------------------Environment Information
Number of fan trays
: 1
Number of fans
: 3
Fan tray number
Status
Speed
: 1
: up
: half speed
------------------------------------------------------------------------------Power Supply Information
Number of power supplies
: 2
Power supply number
Configured power supply type
Status
DC power
Input power
Output power
:
:
:
:
:
:
1
dc
failed
out of range
out of range
within range
Power supply number
Configured power supply type
Status
DC power
Input power
Output power
:
:
:
:
:
:
2
dc
up
within range
within range
within range
7210 SAS D, E OS Basic System Configuration Guide
Page 313
System Commands
===============================================================================
A:7210-SAS-E>
A:7210-SAS-E> show chassis
===============================================================================
Chassis Information
===============================================================================
Name
: STU2597
Type
: 7210 SAS-E-1
Location
:
Coordinates
:
CLLI code
:
Number of slots
: 2
Number of ports
: 24
Critical LED state
: Off
Major LED state
: Off
Minor LED state
: Off
Over Temperature state
: OK
Base MAC address
: 00:25:ba:04:b9:bc
Hardware Data
Part number
CLEI code
Serial number
Manufacture date
Manufacturing string
Manufacturing deviations
Time of last boot
Current alarm state
:
:
:
:
:
:
:
:
3HE04410ABAC01
IPMK310JRA
NS1026C0341
06292010
2010/11/09 16:12:40
alarm cleared
------------------------------------------------------------------------------Environment Information
Number of fan trays
: 1
Number of fans
: 3
Fan tray number
Status
Speed
: 1
: up
: half speed
------------------------------------------------------------------------------Power Supply Information
Number of power supplies
Page 314
: 2
Power supply number
Configured power supply type
Status
DC power
Input power
Output power
:
:
:
:
:
:
1
dc
up
within range
within range
within range
Power supply number
Configured power supply type
Status
DC power
Input power
:
:
:
:
:
2
dc
up
within range
within range
7210 SAS D, E OS Basic System Configuration Guide
System Management
Output power
: within range
===============================================================================
A:7210-SAS-E>
alarm-contact-input
NOTE: This command is supported only on 7210 SAS-E devices.
Syntax
Context
Description
Output
alarm- contact-input all
alarm-contact-input <alarm-contact-input-id> [detail]
show>alarm-contact
This command displays information of all the alarm contact input pins.
alarm-contact-input Output — The following table describes alarm-contact-input output fields.
Label
Description
Alarm input pin Number
Indicates the pin alarm input pin number.
Alarm input pin Description
Describs the alarm indicating its usage or attribute.
Alarm input pin current
state
Indicates the current state of the alarm contact input
pin.
Alarm output pin used
Indicates the alarm output pin used.
Last state change time
Indicates the previous state change time.
Sample Output
*A:7210-2# show alarm-contact-input 1
===============================================================================
Alarm Contact Input
===============================================================================
Alarm Input Pin Number
: 1
Alarm Input Pin Current State : Disabled
Alarm Output Pin Used
: Major
===============================================================================
*A:7210-2#
*A:7210-2# show alarm-contact-input 1 detail
===============================================================================
Alarm Contact Input
===============================================================================
Alarm Input Pin Number
: 1
Alarm Input Pin Description
:
Alarm Input Pin Current State : Disabled
Alarm Output Pin Used
: Major
Last State Change
: 05/19/2010 11:28:09
===============================================================================
7210 SAS D, E OS Basic System Configuration Guide
Page 315
System Commands
*A:7210-2#
*A:7210-2# show alarm-contact-input all
===============================================================================
Alarm Contact Input
===============================================================================
Alarm Input Pin Number
: 1
Alarm Input Pin Description
:
Alarm Input Pin Current State : Disabled
Alarm Output Pin Used
: Major
Last State Change
: 05/19/2010 11:28:09
Alarm Input Pin Number
: 2
Alarm Input Pin Description
:
Alarm Input Pin Current State : Disabled
Alarm Output Pin Used
: Major
Last State Change
: 05/19/2010 11:28:09
Alarm Input Pin Number
: 3
Alarm Input Pin Description
:
Alarm Input Pin Current State : Disabled
Alarm Output Pin Used
: Major
Last State Change
: 05/19/2010 11:28:09
Alarm Input Pin Number
: 4
Alarm Input Pin Description
:
Alarm Input Pin Current State : Disabled
Alarm Output Pin Used
: Major
Last State Change
: 05/19/2010 11:28:09
===============================================================================
*A:7210-2#
Page 316
7210 SAS D, E OS Basic System Configuration Guide
System Management
Debug Commands
system
Syntax
Context
[no] system
debug
Description
This command displays system debug information.
Syntax
[no] router router-name interface ip-int-name
ntp
Context
Description
debug>system
This command enables and configures debugging for NTP.
The no form of the command disables debugging for NTP.
Parameters
router-name — Base
Default
Base
ip-int-name — maximum 32 characters; must begin with a letter. If the string contains special
characters (#, $, spaces, etc.), the entire string must be enclosed within double quotes.
7210 SAS D, E OS Basic System Configuration Guide
Page 317
System Commands
Clear Commands
cron
Syntax
Context
cron action completed [action-name] [owner action-owner]
clear
Description
This command clears completed CRON action run history entries.
Parameters
action-name — Specifies the action name.
Values
maximum 32 characters
owner action-owner — Specifies the owner name.
Default
TiMOS CLI
screen
Syntax
Context
Description
screen
clear
This command allows an operator to clear the Telnet or console screen.
trace
Syntax
Context
Description
Page 318
trace log
clear
This command allows an operator to clear the trace log.
7210 SAS D, E OS Basic System Configuration Guide
Standards and Protocol Support (7210 SAS D)
Standards Compliance
IEEE 802.1ab-REV/D3 Station
And Media Access Control
Connectivity Discovery
IEEE 802.1d Bridging
IEEE 802.1p/Q VLAN Tagging
IEEE 802.1w Rapid Spanning Tree
Protocol
IEEE 802.1x Port Based Network Access
Control
IEEE 802.1ad Provider Bridges
IEEE 802.1ag Service Layer OAM
IEEE 802.3ah Ethernet in the
First Mile
IEEE 802.3 10BaseT
IEEE 802.3ad Link Aggregation
IEEE 802.3ah Ethernet OAM
IEEE 802.3u 100BaseTX
IEEE 802.3z 1000BaseSX/LX
IANA-IFType-MIB
IEEE8023-LAG-MIB
Protocol Support
DIFFERENTIATED SERVICES
RFC 2474 Definition of the DS Field the
IPv4 and IPv6 Headers (Rev)
RFC 2597 Assured Forwarding PHB
Group (rev3260)
RFC 2598 An Expedited Forwarding
PHB
RFC 3140 Per-Hop Behavior
Identification Codes
RFC 4115 A Differentiated Service TwoRate, Three-Color Marker with
Efficient Handling of in-Profile
Traffic
TCP/IP
RFC 768 UDP
RFC 1350 The TFTP Protocol (Rev.
RFC 791 IP
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 Telnet
RFC 1519 CIDR
Standards and Protocols
RFC 1812 Requirements for IPv4
Routers
RFC 2347 TFTP option Extension
RFC 2328 TFTP Blocksize Option
RFC 2349 TFTP Timeout Intervaland
Transfer Size option
RADIUS
RFC 2865 Remote Authentication Dial In
User Service
RFC 2866 RADIUS Accounting
SSH
draft-ietf-secsh-architecture.txt SSH
Protocol Architecture
draft-ietf-secsh-userauth.txt SSH
Authentication Protocol
draft-ietf-secsh-transport.txt SSH
Transport Layer Protocol
draft-ietf-secsh-connection.txt SSH
Connection Protocol
draft-ietf-secsh- newmodes.txt SSH
Transport Layer Encryption Modes
TACACS+
draft-grant-tacacs-02.txt
NETWORK MANAGEMENT
ITU-T X.721: Information technologyOSI-Structure of Management
Information
ITU-T X.734: Information technologyOSI-Systems Management: Event
Report Management Function
M.3100/3120 Equipment and Connection
Models
TMF 509/613 Network Connectivity
Model
RFC 1157 SNMPv1
RFC 1215 A Convention for Defining
Traps for use with the SNMP
RFC 1907 SNMPv2-MIB
RFC 2011 IP-MIB
RFC 2012 TCP-MIB
RFC 2013 UDP-MIB
RFC 2096 IP-FORWARD-MIB
RFC 2138 RADIUS
RFC 2571 SNMP-FRAMEWORKMIB
RFC 2572 SNMP-MPD-MIB
RFC 2573 SNMP-TARGET-&NOTIFICATION-MIB
RFC 2574 SNMP-USER-BASEDSMMIB
RFC 2575 SNMP-VIEW-BASEDACMMIB
RFC 2576 SNMP-COMMUNITY-MIB
RFC 2665 EtherLike-MIB
RFC 2819 RMON-MIB
RFC 2863 IF-MIB
RFC 2864 INVERTED-STACK-MIB
RFC 3014 NOTIFICATION-LOGMIB
RFC 3164 Syslog
RFC 3273 HCRMON-MIB
RFC 3411 An Architecture for
Describing Simple Network
Management Protocol (SNMP)
Management Frameworks
RFC 3412 - Message Processing and
Dispatching for the Simple Network
Management Protocol (SNMP)
RFC 3413 - Simple Network
Management Protocol (SNMP)
Applications
RFC 3414 - User-based Security Model
(USM) for version 3 of the Simple
Network Management Protocol
(SNMPv3)
RFC 3418 - SNMP MIB
draft-ietf-disman-alarm-mib-04.txt
PROPRIETARY MIBs
TIMETRA-CHASSIS-MIB.mib
TIMETRA-CLEAR-MIB.mib
TIMETRA-DOT3-OAM-MIB.mib
TIMETRA-FILTER-MIB.mib
TIMETRA-GLOBAL-MIB.mib
TIMETRA-IEEE8021-CFM-MIB.mib
TIMETRA-LAG-MIB.mib
TIMETRA-LOG-MIB.mib
TIMETRA-MIRROR-MIB.mib
TIMETRA-NTP-MIB.mib
TIMETRA-OAM-TEST-MIB.mib
TIMETRA-PORT-MIB.mib
TIMETRA-QOS-MIB.mib
TIMETRA-SAS-IEEE8021-CFMMIB.mib
TIMETRA-SAS-GLOBAL-MIB.mib
TIMETRA-SAS-PORT-MIB.mib
Page 319
Standards and Protocols
TIMETRA-SAS-QOS-MIB.mib
TIMETRA-SAS-SYSTEM-MIB.mib
TIMETRA-SCHEDULER-MIB.mib
TIMETRA-SECURITY-MIB.mib
TIMETRA-SERV-MIB.mib
TIMETRA-SYSTEM-MIB.mib
TIMETRA-TC-MIB.mib
TIMETRA-VRTR-MIB.mib
Page 320
Standards and Protocols
Standards and Protocol Support (7210 SAS E)
Standards Compliance
IEEE 802.1ab-REV/D3 Station And
Media Access Control Connectivity
Discovery
IEEE 802.1d Bridging
IEEE 802.1p/Q VLAN Tagging
IEEE 802.1w Rapid Spanning Tree
Protocol
IEEE 802.1x Port Based Network Access
Control
IEEE 802.1ad Provider Bridges
IEEE 802.1ag Service Layer OAM
IEEE 802.3ah Ethernet in the First Mile
IEEE 802.3 10BaseT
IEEE 802.3ad Link Aggregation
IEEE 802.3ah Ethernet OAM
IEEE 802.3u 100BaseTX
IEEE 802.3z 1000BaseSX/LX
ITU-T Y.1731 OAM functions and
mechanisms for Ethernet based
networks
IANA-IFType-MIB
IEEE8023-LAG-MIB
ITU-T G.8032 Ethernet Ring Protection
Switching (version 1)
Protocol Support
DIFFERENTIATED SERVICES
RFC 2474 Definition of the DS Field the
IPv4 and IPv6 Headers (Rev)
RFC 2597 Assured Forwarding PHB
Group (rev3260)
RFC 2598 An Expedited Forwarding
PHB
RFC 3140 Per-Hop Behavior
Identification Codes
MULTICAST
RFC 1112 Host Extensions for IP
Multicasting (Snooping)
RFC 2236 Internet Group Management
Protocol, (Snooping)
RFC 3376 Internet Group Management
Protocol, Version 3 (Snooping)
TCP/IP
RFC 768 UDP
Standards and Protocols
RFC 1350 The TFTP Protocol (Rev.
RFC 791 IP
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 Telnet
RFC 1519 CIDR
RFC 1812 Requirements for IPv4
Routers
RFC 2347 TFTP option Extension
RFC 2328 TFTP Blocksize Option
RFC 2349 TFTP Timeout Intervaland
Transfer Size option
RADIUS
RFC 2865 Remote Authentication Dial In
User Service
RFC 2866 RADIUS Accounting
SSH
draft-ietf-secsh-architecture.txt SSH
Protocol Architecture
draft-ietf-secsh-userauth.txt SSH
Authentication Protocol
draft-ietf-secsh-transport.txt SSH
Transport Layer Protocol
draft-ietf-secsh-connection.txt SSH
Connection Protocol
draft-ietf-secsh- newmodes.txt SSH
Transport Layer Encryption Modes
TACACS+
draft-grant-tacacs-02.txt
NETWORK MANAGEMENT
ITU-T X.721: Information technologyOSI-Structure of Management
Information
ITU-T X.734: Information technologyOSI-Systems Management: Event
Report Management Function
M.3100/3120 Equipment and Connection
Models
TMF 509/613 Network Connectivity
Model
RFC 1157 SNMPv1
RFC 1215 A Convention for Defining
Traps for use with the SNMP
RFC 1907 SNMPv2-MIB
RFC 2011 IP-MIB
RFC 2012 TCP-MIB
RFC 2013 UDP-MIB
RFC 2096 IP-FORWARD-MIB
RFC 2138 RADIUS
RFC 2571 SNMP-FRAMEWORKMIB
RFC 2572 SNMP-MPD-MIB
RFC 2573 SNMP-TARGET-&NOTIFICATION-MIB
RFC 2574 SNMP-USER-BASEDSMMIB
RFC 2575 SNMP-VIEW-BASEDACMMIB
RFC 2576 SNMP-COMMUNITY-MIB
RFC 2665 EtherLike-MIB
RFC 2819 RMON-MIB
RFC 2863 IF-MIB
RFC 2864 INVERTED-STACK-MIB
RFC 3014 NOTIFICATION-LOGMIB
RFC 3164 Syslog
RFC 3273 HCRMON-MIB
RFC 3411 An Architecture for
Describing Simple Network
Management Protocol (SNMP)
Management Frameworks
RFC 3412 - Message Processing and
Dispatching for the Simple Network
Management Protocol (SNMP)
RFC 3413 - Simple Network
Management Protocol (SNMP)
Applications
RFC 3414 - User-based Security Model
(USM) for version 3 of the Simple
Network Management Protocol
(SNMPv3)
RFC 3418 - SNMP MIB
draft-ietf-disman-alarm-mib-04.txt
PROPRIETARY MIBs
ALCATEL-IGMP-SNOOPINGMIB.mib
TIMETRA-CAPABILITY-7210-SAS-EV1v0.mib
TIMETRA-CHASSIS-MIB.mib
TIMETRA-CLEAR-MIB.mib
TIMETRA-DOT3-OAM-MIB.mib
TIMETRA-FILTER-MIB.mib
TIMETRA-GLOBAL-MIB.mib
TIMETRA-IEEE8021-CFM-MIB.mib
TIMETRA-LAG-MIB.mib
Page 321
Standards and Protocols
TIMETRA-LOG-MIB.mib
TIMETRA-MIRROR-MIB.mib
TIMETRA-NTP-MIB.mib
TIMETRA-OAM-TEST-MIB.mib
TIMETRA-PORT-MIB.mib
TIMETRA-QOS-MIB.mib
TIMETRA-SAS-ALARM-INPUTMIB.mib
TIMETRA-SAS-IEEE8021-CFMMIB.mib
TIMETRA-SAS-GLOBAL-MIB.mib
TIMETRA-SAS-PORT-MIB.mib
TIMETRA-SAS-QOS-MIB.mib
TIMETRA-SAS-SYSTEM-MIB.mib
TIMETRA-SCHEDULER-MIB.mib
TIMETRA-SECURITY-MIB.mib
TIMETRA-SERV-MIB.mib
TIMETRA-SYSTEM-MIB.mib
TIMETRA-TC-MIB.mib
TIMETRA-VRTR-MIB.mib
Page 322
Standards and Protocols
INDEX
A
configuring 81
command reference 87
copying files 83
creating directories 82
displaying information 85
modifying 81
moving files 84
removing/deleting 84
auto mode 100
B
BOF
overview
image loading
persistence 106
saving a configuration 124
configuring
accessing
the CLI 119
console connection 119
basic 113
BOF parameters 121
command reference 129
management tasks 122
overview 112
rebooting 127
searching for BOF file 116
C
CLI
usage
basic commands 22
command prompt 29
displaying context configurations 30
displaying help 27
entering CLI commands 34
environment commands 25
exec 33
monitor commands 26
navigating 20
structure 18
F
File system
overview
compact flash devices 78
URLs 79
I
image loading 102
L
lldp 222
M
manual mode 99
S
System
overview
backup config files 202
CLLI 158
contact 156
coordinates 157
location 157
name 156
saving configurations 174
time 159
configuring
basic 175
command reference
administration commands 221
system information commands 217
system time commands 219
system administration parameters 203
system parameters 177
system time elements 181
7210 SAS D, E OS Basic System Configuration Guide
Page 323
Index
Page 324
7210 SAS D, E OS Basic System Configuration Guide
">