advertisement
Assembly Instructions
ASSEMBLY RATING
The Assembly Rating is a 5-point system that shows the degree of effort needed in assembling a specific product (with 1 being easy and 5 being difficult). For some products, two persons are recommended.
Tools Required for Assembly:
Allen Wrench
(Included)
Phillips Screwdriver
(Not Included)
EASY DIFFICULT
Page 1 of 7
2 PERSONS RECOMMENDED
Thank you for your purchase!
We hope you will enjoy your new product for many years to come. Our commitment to providing quality products does not simply end when a purchase is made. We stand behind our products and will provide any support needed in order for you to fully enjoy your purchase. Your satisfaction is the greatest recognition we could have.
Because we value your trust in our company, we will do our best to meet your service expectations. Should you have any assembly related questions, parts replacement requests, comments or suggestions, please feel free to contact us any time. To help expedite the service, please have the assembly instructions available, along with your order receipt.
Page 2 of 7
Page 3 of 7
MD
Before you begin, please read Page 3 of “Assembly and Care Advice”.
And remember, do not tighten until each step is completed or instructed.
Parts List
#1 x 1 pc
Table Top
#2 x 4 pcs
Leg
#3 x 2 pcs
Leg Support Frame
Hardware List (Continued)
#C x 10 pcs
Bolt 5/16”x1-1/4”
#D x 16 pcs
Flat Washer 19mm
#E x 10 pcs
Flat Washer 16mm
#4 x 1 pc
Glass Strip
#F x 26 pcs
Lock Washer
#A x 16 pcs
Bolt 5/16”x7/8”
#G x 1 pc
Allen Wrench
#H x 8 pcs
Bracket
#B x 16 pcs
Bolt 5/16”x7/8”
#I x 8 pcs
Cover
Due to the size and/or weight of this product, it is highly recommended that the assembly should be done near the area of its intended location.
Make sure you have enough space to move around during the assembly.
ALWAYS have at least two people to help with transporting and assembling the product to avoid any potential injury and/or damage.
Page 4 of 7
#B x 16 pcs
#H x 8 pcs
I.
Align the two brackets (#H) with the pre-drilled holes of the leg (#2).
II.
Secure the brackets (#H) using the
Allen wrench (#G) to tighten the 4 bolts (#B) to lock them with the leg
(#2).
III.
Repeat the process above for the remaining 3 legs.
Turn right (clockwise) to tighten
#A x 8 pcs
#D x 8 pcs
#F x 8 pcs
Turn right (clockwise) to tighten
I.
With the help of another person, carefully place the table top (#1) facing down on a protective surface.
Align the brackets (#H) assembled onto the two legs (#2) with the predrilled holes on the table top (#1).
II.
Prepare 8 bolt assemblies by inserting
FIRST the lock washer (#F) onto the bolt (#A) and then the flat washer (#D) onto the SAME bolt (#A), in that order.
III. Insert the bolt assemblies through the holes of the brackets (#H) and secure those bolts using the Allen wrench
(#G) to lock them with the table top
(#1).
Page 5 of 7
#C x 4 pcs
#E x 4 pcs
#F x 4 pcs
#I x 4 pcs
I.
Align the two leg support frames (#3) with the two pre-drilled holes of the two legs (#2).
II.
Prepare 4 bolt assemblies by inserting FIRST the lock washer
(#F) onto the bolt (#C) and then the flat washer (#E) onto the
SAME bolt (#C), in that order.
III. Insert the bolt assemblies through the pre-drilled holes of the leg support frames (#3) and secure those bolt using the Allen wrench
(#G) to lock them with the two legs (#2). Once tighten, place the covers (#I) over the bolts (#C).
Turn right (clockwise) to tighten
#A x 8 pcs
#C x 4 pcs
#D x 8 pcs
#E x 4 pcs
#F x 12 pcs
#I x 4 pcs
Repeat Step 2 and Step 3 to assemble the remaining 2 assembled legs (#2) onto the leg support frames (#3) and the table top (#1).
#2
Turn right (clockwise) to tighten
#2 #1
#3
Page 6 of 7
#C x 2 pcs
#E x 2 pcs
#F x 2 pcs
I.
With the help of another person, carefully place the table upright.
II.
Align the glass strip (#4) with the pre-drilled holes of the table top (#1).
III.
Prepare two bolt assemblies by inserting FIRST the lock washer
(#F) onto the bolt (#C) and then the flat washer (#E) onto the
SAME bolt (#C), in that order.
IV.
Insert the bolt assemblies through the pre-drilled holes under the table top (#1) and secure those bolt using the Allen wrench (#G) to lock them with the glass strip (#4).
Make sure the table is rested on a flat surface and does not feel loose or wobbly. If it does, double check that the bolts/screws are secured and properly tightened.
#1
To install the batteries (not included), remove the screw that holds the battery cover by using a Phillips screwdriver.
Install new AA-size 1.5-volt alkaline batteries with correct polarity (
,) by following the illustration inside the battery cover. Close the battery cover and tighten back the screw.
Caution:
Use batteries of the same type.
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.
Do not use rechargeable batteries.
Do not try to recharge non-rechargeable batteries.
Remove exhausted or corroded batteries.
If light is not used for more than a week, remove the batteries to prevent depletion and corrosion.
Page 7 of 7
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement