- Computers & electronics
- Cameras & camcorders
- Camera accessories
- Photo studio flash units
- User manual
advertisement
▼
Scroll to page 2
of 5
Amazing “Multi-Freeze Compact Flash” 深圳市神牛摄影器材有限公司 GODOX Photo Equipment Co., Ltd 地址/Add: 深圳市宝安区福永镇福洲大道西新和村华发工业园A4栋 Building A4, Xinhe Huafa Industrial Zone, Fuzhou RD West, Fuyong Town, Baoan District, Shenzhen 518103, China 电话/Tel: +86-755-29609320(8062) 传真/Fax: +86-755-25723423 邮箱/E-mail: [email protected] 705-QU6000-00 Instruction Manual Made In China 说 明 手 册 Chinese English Bilingual 中英文双语 维护保养 FOREWORD 闪光灯在工作时,如发现异常时,应立即关掉电源,查明原因。 灯体应避免震动,平时注意表面除尘。 灯体稍有发热为正常现象,无特别需要时,勿连续引闪。 除灯管与造型灯消耗品用户可用原厂配置的自行装卸更换外,所有闪光灯概 由本厂指定可供原厂配件之维修部负责。 Thanks for choosing Quicker high-speed flash. It has wide-range applicability, not only perfect for all kinds of studio and workshop photography, but also good at wedding, portrait, advertisement, and fashion photography. Without recycling time limits, photographers can capture a series of fast-changing facial expressions and amazing moves, and clearly freeze each fleetingly perfect instant into eternal beauty. Among the benefits you’ll enjoy: 1年保修,由于灯管与造型灯为消耗品,不在1年保修范围。 经发现擅自检修此闪光灯,将取消闪光灯之一年保修期,维修需要收取相关 费用。 如果本品出现故障或者被水淋湿,唯有在专业人员维修后方可继续使用。 在维修和清洁本品时请断开电源。 如有技术更改,恕不另行通知。 Ultra-speedy charging, 0.05-1.2s recycling time Multi-freeze shots, 1/5000s-1/800s flash duration Up to 10 shots in one second under high-speed continuous shooting Exact output control on LED display, 50 steps from 5.0-10.0 by 0.1 increment High qualified modeling lamp, 150W output adjustable Outstanding output stability, less than 2% shifts when under the same output High color stability, ranging within ±100k between flashes over the entire power range Flash output on/off and power level,modeling lamp and buzzer on/off,and flash triggering can be controlled by using Godox FT series romote control. CONTENTS 08 09 09 10 10 11 11 11 11 12 12 - 07 - Foreword Warning Caution Names of Parts • Body • Accessories • Separately Sold Accessories Operations • Flash Preparation • Power Connection • Modeling Lamp 12 12 12 12 13 13 13 13 14 14 - 08 - • Power Output Control • Test Button • Sync Triggering • Slave Trigger Model • Buzz Function • Memory Function • Wireless Control Function • Tube Replacement Technical Data Maintenance Warning NAMES OF PARTS To prevent damage to the product or injury to you or to others, read the following warnings in their entirety before using this product. Keep these safety instructions where users can read them for ready reference. Do not disassemble or modify. Should the product break down, send the defective back to the authorized service center for inspection and maintenance. Keep dry. Do not handle with wet hands, immerse in water, or expose to rain. Keep out of reach of children. Please put the device in a ventilation environment and keep the parts of lighting and heat dissipation holes are unobstructed. Do not use in flammable environment. As this product adopts make and break device, please keep it easy to be used. No touching the heating parts of this product. Please turn off the power and wear insulated gloves before installing and connecting accessories. When replacing the tube or modeling lamp, please make sure that the tube is cool and wear insulated gloves to prevent burns. Do not flash directly towards naked eyes (especially those of babies), otherwise it may lead to visual impairment. Disconnect from the power supply when it will not be used for an extended period. CAUTION After 30 continuous flashes at full power, the flash should be cooled down for about 3 minutes. Overheating will occur if it is used continuously without cooling down. Do not keep using the modeling lamp for a long time; otherwise flammable accessories attaching to flash head, e.g. softbox will get burnt. A 10-minute time is recommended in this case. After 10 minutes, cool it down for 1 minute. Body 15 18 10 13 12 05 04 11 07 06 14 08 09 03 02 20 16 01 19 17 1. AC Power Socket 2. Sync Cord Jack 3. Power Switch 4. Modeling Lamp Output Controller 5. Flash Output Controller 6. Modeling Lamp Button MODEL 7. Sound Button 8. Slave Model Button SLAVE 9. Test Button 10. Digital Display 11. Modeling Lamp Indicator 12. Buzz Indicator 13. Slave Trigger Indicator 14. Test Indicator Lamp When using a snoot, do not keep the modeling lamp on for a long time or fire too frequently (not over six times for one minute). Overheating will result in damages for strobe housing and/or studio light. Avoid sudden impacts as this can damage the flash tube and/or modeling lamp. - 09 - - 10 - 15. Light Sensor 16. Fuse 17. Mounting Bracket 18. Umbrellas Input 19. Direction Adjusting Handle 20. Wireless Control Port Accessories 1. 2. 3. 4. 5. 6. Power Cord Standard Reflector Lamp Cover Glass Protection Cover Modeling Lamp Instruction Manual Power Connection 1 2 5 3 4 Use the power cord to connect the flash to an AC power source and turn on the power switch (3). The lamp on the power switch turns on, indicating it’s connected. Modeling Lamp Separately sold accessories The product can be used in combination with the following accessories sold separately, so as to achieve best photography effects: FT-16 Remote Control, Power Inverter, Softbox, Photographic Umbrella, Light Stand, Barndoor, Snoot, etc. Modeling Lamp Button (6) controls the modeling lamp status: when modeling lamp indicator lit up, modeling lamp turns on;when modeling lamp indicator off,modeling lamp turns off. Modeling lamp output controller (4) can be used to adjust the modeling lamp power output. Modeling lamp will turn off automatically after lighting for 2 hours, in case it's forgotten to turn off when user is not nearby. When there is flammable accessory on the flash unit, do not keep the modeling lamp on for a long time. It is recommended to cool it down for one minute after 10 minutes' working. Power Output Control Flash output controller (5) decides different power output, satisfying the light requirements in different environment. The power is adjustable freely from 5.0 to 10.0 which will be accordingly told on the digital display (10). “OF”on the display indicated that the flash triggering function is turned off. It can discharge automatically when the flash output is adjusted from high to low. Test Button To fire the flash without taking a picture, press the test button (9). It can also help adjust the flash brightness when combined with the flash output controller (5). OPERATIONS Sync Triggering Flash Preparation The sync cord jack (2) is a Φ6.35mm plug. Insert a trigger plug here and the flash will be fired synchronously with the camera shutter. 1. Take down the lamp cover. Install the modeling lamp and put on the glass protection cover and the standard reflector. (To uninstall the standard reflector, press the orange release button on the flash head and turn the standard reflector counter-clockwise to take it out, as illustrated in the picture.) 2. Attach the flash unit on an appropriate light stand. Adjust the mounting bracket (17) for a good angle and make sure it’s tightened and fixed. Use the direction adjusting handle (19) to adjust the flash on a desired direction. Umbrella input (18) is for different photo umbrellas to put in. Three slave triggering models are available and can be set by pressing Slave Model Button (8). 1) No optical control: The slave triggering indicator (13) is off, indicating the slave triggering function is shut down. 2) One fire model: The slave triggering indicator (13) glows blue, indicating the flash will fire synchronously after receiving one external flash. In this model, the flash can function as an auxiliary lamp, offering various effects of light and shadow. 3) Anti-preflash model: The slave triggering indicator (13) glows red, indicating the flash will receive two external flashes within 2 seconds and will fire synchronously after receiving the second flash. In this model, the flash can function as an auxiliary lamp, applicable to TTL - 11 - - 12 - Slave Trigger Model system. With this anti-preflash function, synchronization is supported with cameras having a one-preflash firing system. TECHNICAL DATA Model Buzz Function The sound button (7) is used to decide whether there is sound reminder for ready flash after recharging. When the buzz indicator (12) turns on, it means buzz function is working; if it turns off, the buzz function is not working. A “BI” sound will be heard when it’s fully charged. Memory Function The device is equipped with memory function for the panel setting. It will help remember the panel setting 3 second after you set it. When starting up the flash next time, the panel setting will be the same as the status before powering it off. Max Power (WS) Guide Number(m ISO 100) Quicker400 Quicker600 300WS 400WS 600WS 58 65 76 Color Temperature 5600K±100K Operating Voltage AC110V-120V~60Hz or AC220V-240V~50Hz 5.0~10.0 (1/1~1/128) Power Output Control 150W Modeling Lamp (W) 0.05~1.2sec Recycle Time Triggering Method Wireless Control Function Quicker300 sync cord, test button, slave, wireless control port 1/5000S~1/800S Flash Duration By using the wireless power-control flash trigger, you can wirelessly control the on-and-off of your flash, modeling lamp and buzzer, as well as adjust the flash output level. To start this function, insert the trigger receiver into the Wireless Control Port (20) and make settings on the trigger. You can also press the camera shutter-release button to trigger the flash by setting the transmitter hotshoe onto the camera hotshoe. Tube Replacement Shut down the power and remove the power cord before replacing the flash tube and wear insulated gloves. Then, loosen the iron wire on the tube, keep a balanced hold on the two feet of the flash tube and pull out the old tube gently. Take down the feet casing from the old tube and put it on the new one. Hold two feet of the new tube, and target directly towards the two copper outlets, then push them slightly in. Twine the iron wire on the stainless steel sheet to fix the flash tube. - 13 - 9V Parameters Output from the Sync Cord Jack 5V/200mA (only for the receiver) Parameters Output from the USB Port AC110-120V~60Hz: 10A Fuse AC220V-240V~50Hz: 5A AC220V-240V~50Hz:8A Dimension Flash diameterΦ14CM, height of flash with handle 23CM, length of flash with lamp cover 41CM Net Weight Approx. 2.7KG Approx. 2.8KG Approx. 3KG MAINTENANCE Shut down the device immediately when it works abnormally and find out the reason. Avoid sudden impacts and the lamp should be dedusted usually. It’s normal for lamp being warm when in use. Avoid continuous flashes when it is not necessary. Maintenance of all the flashes is up to our authorized maintenance department which can provide original accessories. Users can replace the flash tube and modeling lamp provided by the manufacturer. One year warranty period will be cancelled when any unauthorized maintenance is found. If the product had failures or was wetted, it can be continuously used only after it is repaired by professionals. Disconnect the power when doing maintenance work or cleaning. New changes made to the specifications or designs may not be updated in this manual. - 14 -
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project