Panasonic DMP-BDT360 Blu-ray Player Owner's Manual

PDF
سند
تبلیغات
DMP-BDT460_360_SQT0080_eng.book
1 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Owner’s Manual
Blu-ray DiscTM Player
Model No. DMP-BDT460
DMP-BDT361
DMP-BDT360
Firmware updates
Panasonic is constantly improving the unit’s firmware to ensure
that our customers are enjoying the latest technology.
Panasonic recommends updating your firmware as soon as you
are notified.
For details, refer to “Firmware updates” (&gt; 13) or
http://panasonic.jp/support/global/cs/ (This site is in English only.)
Thank you for purchasing this product.
Please read these instructions carefully before using this product, and save this manual for future use.
If you have any questions, visit :
U.S.A. and Puerto Rico : www.panasonic.com/support
Canada : www.panasonic.ca/english/support
Register online at www.panasonic.com/register (U.S. customers only)
P
PC
SQT0080
until
2014/02/10
DMP-BDT460_360_SQT0080_eng.book
2 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Getting started
THE FOLLOWING APPLIES IN THE U.S.A.
AND CANADA
IMPORTANT SAFETY
INSTRUCTIONS
Read these operating instructions carefully before using the unit.
Follow the safety instructions on the unit and the applicable safety
instructions listed below. Keep these operating instructions handy for
future reference.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with one
wider than the other. A grounding-type plug has two blades and
a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the
obsolete outlet.
Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
Only use attachments/accessories specified by the
manufacturer.
Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
Unplug this apparatus during lightning
storms or when unused for long periods of
time.
Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE SCREWS.
NO USER-SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
2
SQT0080
This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of this device.
Contains FCC ID : NKR-P1
Contains IC : 4441A-P1
This transmitter must not be co-located or operated in conjunction
with any other antenna or transmitter.
This product is restricted to indoor use due to its operation in the
5.15 to 5.25 GHz frequency range.
FCC and IC require this product to be used indoors for the frequency
range 5.15 to 5.25 GHz to reduce the potential for harmful
interference to co-channel Mobile Satellite systems. High power
radars are allocated as primary users of the 5.25 to 5.35 GHz and
5.65 to 5.85 GHz bands. These radar stations can cause
interference with and/or damage this product.
This equipment complies with FCC/IC radiation exposure limits set
forth for an uncontrolled environment and meets the FCC radio
frequency (RF) Exposure Guidelines in Supplement C to OET65 and
RSS-102 of the IC radio frequency (RF) Exposure rules. This
equipment has very low levels of RF energy that is deemed to
comply without maximum permissive exposure evaluation (MPE).
But it is desirable that it should be installed and operated keeping
the radiator at least 20 cm (7 7/8q) or more away from person’s body
(excluding extremities: hands, wrists, feet and ankles).
THE FOLLOWING APPLIES ONLY IN THE U.S.A.
FCC Note:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
≥ Reorient or relocate the receiving antenna.
≥ Increase the separation between the equipment and receiver.
≥ Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
≥ Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, follow the attached
installation instructions and use only shielded interface cables when
connecting to peripheral devices.
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
this equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Declaration of Conformity
Trade Name: Panasonic
Model No.: DMP-BDT361
DMP-BDT360
Responsible Party:
Panasonic Corporation of North America
Two Riverfront Plaza, Newark, NJ 07102-5490
Support Contact: http://www.panasonic.com/contactinfo
THE FOLLOWING APPLIES ONLY IN CANADA.
CAN ICES-3(B)/NMB-3(B)
DMP-BDT460_360_SQT0080_eng.book
3 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Precautions
WARNING
Unit
To reduce the risk of fire, electric shock or product damage,
≥ Do not expose this unit to rain, moisture, dripping or splashing.
≥ Do not place objects filled with liquids, such as vases, on this unit.
≥ Use only the recommended accessories.
≥ Do not remove covers.
≥ Do not repair this unit by yourself. Refer servicing to qualified
service personnel.
AC power supply cord
≥ The power plug is the disconnecting device. Install this unit so that
the power plug can be unplugged from the socket outlet
immediately.
Small object
≥ Keep the Memory Card out of reach of children to prevent
swallowing.
CAUTION
Unit
≥ This unit utilizes a laser. Use of controls or adjustments or
performance of procedures other than those specified herein may
result in hazardous radiation exposure.
≥ Do not place sources of naked flames, such as lighted candles, on
this unit.
Placement
To reduce the risk of fire, electric shock or product damage,
≥ Do not install or place this unit in a bookcase, built-in cabinet or in
another confined space. Ensure this unit is well ventilated.
≥ Do not obstruct this unit’s ventilation openings with newspapers,
tablecloths, curtains, and similar items.
≥ Do not place the unit on amplifiers/receivers or equipment that
may become hot. The heat can damage the unit.
Batteries
Mishandling of batteries can cause electrolyte leakage and may
cause a fire.
≥ Danger of explosion if battery is incorrectly replaced. Replace only
with the type recommended by the manufacturer.
≥ When disposing the batteries, please contact your local authorities
or dealer and ask for the correct method of disposal.
≥ Do not mix old and new batteries or different types at the same
time.
≥ Do not heat or expose to flame.
≥ Do not leave the battery(ies) in a car exposed to direct sunlight for
a long period of time with doors and windows closed.
≥ Do not take apart or short circuit.
≥ Do not recharge alkaline or manganese batteries.
≥ Do not use batteries if the covering has been peeled off.
Remove batteries if you do not intend to use the remote control for a
long period of time. Store in a cool, dark place.
Wireless LAN connection
The following limits are in place regarding the usage of this unit. You
must be aware of these limits before using this unit.
Panasonic will in no way be responsible for any incidental damage
which may arise due to a failure to obey these limits, or to any
condition of use or disuse of this unit.
≥ Data transmitted and received over radio waves may be
intercepted and monitored.
≥ This unit contains delicate electronic components.
Please use this unit in the manner in which it was intended and
follow the following points:
– Do not expose this unit to high temperatures or direct sunlight.
– Do not bend, or subject this unit to strong impacts.
– Keep this unit away from moisture.
– Do not disassemble or alter this unit in any way.
Restriction on use of
unauthorized copied content
This unit adopts the following technology for copyright protection.
Cinavia Notice
This product uses Cinavia technology to limit the use of unauthorized
copies of some commercially-produced film and videos and their
soundtracks. When a prohibited use of an unauthorized copy is
detected, a message will be displayed and playback or copying will be
interrupted.
More information about Cinavia technology is provided at the Cinavia
Online Consumer Information Center at http://www.cinavia.com. To
request additional information about Cinavia by mail, send a postcard
with your mailing address to:
Cinavia Consumer Information Center, P.O. Box 86851, San Diego,
CA, 92138, USA.
To dispose or transfer this unit
The unit may keep the user settings information in the unit. If you
discard this unit either by disposal or transfer, then follow the
procedure to return all the settings to the factory presets to delete the
user settings. (&gt; 30, “To return all settings to the factory preset.”)
≥ The operation history may be recorded in the memory of this unit.
Information on Disposal in other Countries outside
the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact
your local authorities or dealer and ask for the
correct method of disposal.
Conforms to UL STD 60065.
Certified to CAN-CSA STD C22.2 No.60065.
(Inside of product)
SQT0080
3
DMP-BDT460_360_SQT0080_eng.book
4 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Table of contents
IMPORTANT SAFETY
INSTRUCTIONS. . . . . . . . . . . 2
Precautions . . . . . . . . . . . . . . . 3
Settings
Option menu . . . . . . . . . . . . . . 22
Setup menu. . . . . . . . . . . . . . . 24
Getting started
Accessories . . . . . . . . . . . . . . .
Unit and media care . . . . . . . . .
Playable media. . . . . . . . . . . . .
Control reference guide . . . . . .
5
5
6
8
Connections and Settings
Connecting to a TV. . . . . . . . . . 9
Connecting to
an amplifier/receiver . . . . . . . . 9
Connecting to the network . . . 11
Settings . . . . . . . . . . . . . . . . . 12
Playback
Inserting or
removing media . . . . . . . . . .
HOME menu. . . . . . . . . . . . . .
Multi User Mode . . . . . . . . . . .
Playback. . . . . . . . . . . . . . . . .
Network Service
(Enjoying Netflix, etc.). . . . . .
Home Network feature . . . . . .
“HDMI CEC” . . . . . . . . . . . . . .
4
SQT0080
14
15
16
17
19
20
22
Reference
Troubleshooting guide . . . . . . 30
Specifications . . . . . . . . . . . . . 34
Limited Warranty . . . . . . . 37, 38
Referencia r&aacute;pida en espa&ntilde;ol
(Spanish Quick Reference) . . . . 39
Index . . . . . . . . . . . . . Back cover
5 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Accessories
Check the supplied accessories before using this
unit.
Remote control
(N2QAYB000953)
Batteries for remote control
AC power supply cord
(K2CB2YY00092)
The enclosed Canadian French label sheet corresponds
to the English display on the unit.
Use the lens cleaner (not supplied) to clean the
unit’s lens.
∫ Clean discs
≥ Product numbers are provided in this Owner’s Manual
correct as of December 2013. These may be subject to
change.
≥ Do not use AC power supply cord with other equipment.
∫ Using the remote control
Insert the batteries to the terminal so that it (i
and j) matches those in the remote control.


R6/LR6, AA
(Alkaline or manganese batteries)
Point it at the remote control signal sensor on this
unit. (&gt; 8)
DO
DO NOT
Wipe with a damp cloth and then wipe dry with a
dry cloth.
Connections and Settings
∫ This unit’s lens
[For_Canada]
∫ Disc and card handling
precautions
≥ Handle discs by the edges to avoid inadvertent
scratches or fingerprints on the disc.
≥ Do not attach labels or stickers to discs.
≥ Do not use disc cleaning sprays, benzine,
thinner, static electricity prevention liquids or
any other solvent.
≥ Clean any dust, water, or foreign matter from
the terminals on the rear side of the card.
≥ Do not use the following discs:
– Discs with exposed adhesive from removed
stickers or labels (rented discs, etc.).
– Discs that are badly warped or cracked.
– Irregularly shaped discs, such as heart
shapes.
Playback
1
≥ Never use alcohol, paint thinner or benzine to
clean this unit.
≥ Before using chemically treated cloth, carefully
read the instructions that came with the cloth.
Settings
2
∫ Clean this unit with a soft, dry
cloth
Reference
1
Unit and media care
Getting started
DMP-BDT460_360_SQT0080_eng.book
SQT0080
5
DMP-BDT460_360_SQT0080_eng.book
6 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Playable media
Device
Media
markings
Device types
BD-Video
BD-RE
BD
BD-R
DVD-Video
DVD-R
DVD
DVD-R DL
Contents format
Video
Video,
JPEG, MPO
Video, MKV,
Xvid [For[Canada]
Video
Video, AVCHD,
MKV, Xvid [For[Canada],
JPEG, MPO,
AAC, FLAC, MP3, WAV,
WMA
DVD-RW
Video, AVCHD
—
+R/+RW/+R DL
Music CD
CD
—
MKV, Xvid [For[Canada],
JPEG, MPO
AAC, FLAC, MP3,
Music [CD-DA], WAV,
WMA
SD Memory Card (from 8 MB to 2 GB)
AVCHD, AVCHD 3D,
SDHC Memory Card (from 4 GB to 32 GB)
MP4,
SDXC Memory Card (48 GB, 64 GB)
JPEG, MPO
(Compatible with both mini and micro types)
SD
USB
CD-R
CD-RW
Music [CD-DA]
—
USB devices
(up to 2 TB)
MKV, MP4, MPEG2,
Xvid [For[Canada],
JPEG, MPO,
AAC, FLAC, MP3, WAV,
WMA
≥ See pages 7 and 34 for more information on the types of content that can be played.
6
SQT0080
7 ページ ２０１３年１２月１９日　木曜日　午後３時０分
∫ Types of discs that cannot be
played in this unit
Any other disc that is not specifically
supported or previously described.
≥ DVD-RAM
≥ Super Audio CD
≥ Photo CD
≥ DVD-Audio
≥ Video CD and Super Video CD
≥ HD DVD
The unit can play back BD-Video/DVD-Video
discs of the following regions codes, including
“ALL”:
BD-Video
≥ Operation and sound quality of CDs that do not
comply with CD-DA specifications (copy control
CDs, etc.) cannot be guaranteed to work.
≥ The digital audio content side of a DualDisc
does not meet the technical specifications of
the Compact Disc Digital Audio (CD-DA) format
so playback may not be possible.
∫ SD card
∫ Region management information
Example:
∫ Music CD
DVD-Video
1
≥ The unit cannot playback discs in PAL format.
∫ Finalize
Any DVD-R/RW/R DL, +R/+RW/+R DL and
CD-R/RW that are recorded by a recorder need to
be finalized by the recorder to play on this unit.
Please refer to the recorder’s owner’s manuals.
∫ BD-Video
≥ This unit supports high bit rate audio (Dolby&reg;
Digital Plus, Dolby&reg; TrueHD, DTS-HD High
Resolution AudioTM and DTS-HD Master
AudioTM) adopted in BD-Video.
≥ [BDT361] [BDT360] : If “Dolby D/Dolby D +/Dolby
TrueHD” is set to “PCM” and “DTS Neo:6” is set
to “Off”, the maximum possible number of
Dolby&reg; sound is 5.1ch PCM. (&gt; 25)
∫ 3D
≥ 3D videos and 3D still pictures can be played
back when this unit is connected to a 3D
compatible TV using a High Speed HDMI
Cable.
≥ 2D video can be enjoyed as 3D virtually. (&gt; 23)
≥ miniSD Cards, microSD Cards,
microSDHC Cards and microSDXC
Cards can be used, but must be used
with an adaptor card. These are
usually supplied with such cards, or
otherwise customer provided.
≥ To protect the card’s contents, move
the record prevention tab (on the SD card) to
“LOCK”.
≥ This unit is compatible with SD Memory Cards
that meet SD Card Specifications FAT12 and
FAT16 formats, as well as SDHC Memory
Cards in FAT32 format and SDXC Memory
Cards in exFAT.
≥ If the SD card is used with incompatible
computers or devices, recorded contents may
be erased due to the card being formatted etc.
≥ Usable memory may be slightly less than the
card capacity.
∫ USB device
≥ This unit does not guarantee connection with all
USB devices.
≥ This unit does not support USB device
charging.
≥ FAT12, FAT16, FAT32, and NTFS file systems
are supported.
≥ This unit supports USB2.0 High Speed.
≥ This unit supports an HDD formatted in FAT32
and NTFS. If the HDD is not recognized, the
power to the HDD may not be supplied. Supply
power from an external source.
≥ It may not be possible to play the above media in some
cases due to the type of media, the condition of the
recording, the recording method, and how the files were
created.
≥ The producers of the disc can control how discs are
played, so you may not always be able to control play as
described in this Owner’s Manual. Read the disc’s
instructions carefully.
SQT0080
7
Getting started
DMP-BDT460_360_SQT0080_eng.book
DMP-BDT460_360_SQT0080_eng.book
8 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Control reference guide
When other Panasonic devices respond to the
remote control of the unit, change the remote
control code. (&gt; 28)
1
2
10
1
2
11
12
3
13
3
4
5
6
14
15
4
16
7
8
9
5
6
17
18
10
11
12
13
19
7
20
8
14
15
16
21
9
17
18
19
20
21
8
9
10
Pull to flip down
the front panel.
SD CARD
1
2
3
4
5
8
1
2 3 4 5
Disc tray (&gt; 14)
Remote control signal sensor
Distance: Within approx. 7 m (23 feet)
Angle: Approx. 20e up and down, 30e left and right
[BDT460] [BDT361/360_for_U.S.A.]
Blue LED
It is possible to set the LED to turn on/off. (&gt; 28)
SD card slot (&gt; 14)
[BDT460] V.OFF LED (Video off LED)
It is possible to set the LED to turn on/off. (&gt; 28)
SQT0080
Turn the unit on and off
TV operation buttons
You can operate the Panasonic TV using this
unit’s remote control. Some buttons may not
work depending on the TV.
[&Iacute; TV] : Turn the TV on and off
[AV] : Change input
[i j VOL] : Adjust the volume
Select title numbers, etc./Enter numbers or
characters
Cancel
Basic playback control buttons (&gt; 17)
Show Closed Caption setup screen
(&gt; 23, 26)
Show Pop-up menu/Top menu (&gt; 17)
Show Option menu (&gt; 22)
Colored buttons (red, green, yellow, blue)
Used for various purposes depending on the
display.
Transmit the remote control signal
Open or close the disc tray (&gt; 14)
Show the status messages (&gt; 18)
Switch Secondary Video on/off
(Picture-in-picture) (&gt; 23)
Change audio (&gt; 17)
Show MiracastTM screen (&gt; 20)
Show the Home Screen of Network Service
(&gt; 19)
Exit the Menu screen
Show Netflix screen (&gt; 19)
Show HOME menu (&gt; 15)
[3, 4, 2, 1] : Move the highlight for selection
[OK] : Confirm the selection
(;1) : Frame-by-frame (&gt; 17)
Return to previous screen
6
6
7
8
9
10
7
USB port (&gt; 14)
Display
Open or close the disc tray (&gt; 14)
Basic playback control switches (&gt; 17)
Standby/on switch (&Iacute;/I) (&gt; 12)
Press to switch the unit from on to standby
mode or vice versa. In standby mode, the unit
still consumes a small amount of power.
Rear panel terminals (&gt; 9–11)
DMP-BDT460_360_SQT0080_eng.book
9 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Connecting to a TV
Connections and Settings
≥ Before making any connections, we recommend that you temporarily disconnect all the units from AC
power outlet.
≥ Use the High Speed HDMI cables. Non-HDMI-compliant cables cannot be utilized. It is recommended
that you use Panasonic’s HDMI cable. When outputting 1080p or 24p (4K) signal, please use HDMI
cables 5.0 meters (16.4 ft.) or less.
To an AC outlet
[BDT460]
HDMI cable
HDMI IN
[BDT361]
[BDT360]
AC power supply cord
(supplied)
≥ [BDT460] : Use HDMI AV OUT MAIN terminal.
≥ This unit consumes a small amount of AC power (&gt; 34) even when turned off in standby mode. For
the purpose of energy conservation, the unit should be disconnected if you will not be using it for
extended period of time.
Connecting to an amplifier/receiver
Perform either one of the following connections in accordance with your amplifier/receiver input
terminal.
HDMI AV OUT
[BDT460]
HDMI cable
HDMI cable
HDMI IN
HDMI OUT
(ARC)
Getting started
Connect the power supply cord after making all connections.
HDMI IN
(ARC)
[BDT361]
[BDT360]
Amplifier/receiver
≥ [BDT460] : Use HDMI AV OUT MAIN terminal.
≥ Set “Digital Audio Output” (&gt; 25).
≥ When connecting to a non-3D or 4K compatible amplifier/receiver, connect this unit to a TV, then
connect the TV and the amplifier/receiver. Please note, however, that the audio can only be up to
5.1ch.
≥ When using the TV or amplifier/receiver that does not have the indication of “(ARC)”
(non-ARC-compatible) on the HDMI terminal, the amplifier/receiver and TV must also be connected
using an optical digital cable in order to enjoy the TV’s sound through the amplifier/receiver.
SQT0080
9
DMP-BDT460_360_SQT0080_eng.book
10 ページ ２０１３年１２月１９日　木曜日　午後３時０分
HDMI AV OUT SUB [BDT460]
You can enjoy richer sound by using the HDMI AV OUT SUB terminal.
HDMI cable
HDMI cable
HDMI IN
HDMI IN
Amplifier/receiver
≥ Set “HDMI(SUB) Output Mode” to “V.OFF”. (&gt; 25)
– Audio is output in high resolution regardless of compatibility of the amplifier/receiver with 3D.
≥ It is possible to play back 3D videos, 3D still pictures and 24p (4K) videos, etc., when the connected
TV is 3D or 4K compatible, even if the amplifier/receiver is not 3D or 4K compatible.
≥ The HDMI connection using HDMI AV OUT MAIN supports HDMI CEC (&gt; 22).
The HDMI AV OUT SUB terminal is not compatible with the HDMI CEC.
OPTICAL
Optical digital cable
OPTICAL IN
Amplifier/receiver
≥ Set “HDMI Audio Output” to “Off” (&gt; 25).
≥ Set “Digital Audio Output” (&gt; 25).
10
SQT0080
DMP-BDT460_360_SQT0080_eng.book
11 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Connecting to the network
Wireless LAN connection
This unit has built-in Wi-Fi&reg; and can be connected to a wireless router.
Wireless router, etc.
Internet
≥ For up-to-date compatibility information on your wireless router, refer to
http://panasonic.jp/support/global/cs/
(This site is in English only.)
For additional information about this unit refer to
http://www.panasonic.com/support (For U.S.A.)
≥ The unit is not compatible with public wireless LAN services provided in airports, stations, cafes, etc.
≥ See page 3 for the precautions for wireless LAN connection.
LAN cable connection
LAN Cable
Broadband router, etc.
Internet
≥ Use category 5 or above straight LAN cables (STP) when connecting to peripheral devices.
≥ Inserting any cable other than a LAN cable in the LAN port can damage the unit.
SQT0080
11
Connections and Settings
The following services can be used when this unit is connected to broadband.
≥ Firmware can be updated (&gt; 13)
≥ You can enjoy BD-Live (&gt; 18)
≥ You can enjoy Network Service (&gt; 19)
≥ You can access other devices (Home Network) (&gt; 20)
≥ This unit supports Wi-Fi DirectTM and can make a wireless connection to wireless devices without
router. You can use this function when enjoying Home Network feature, etc. Internet access is not
available while connected via Wi-Fi DirectTM. (&gt; 20, 26)
For details about connection method, refer to the instructions supplied with the connected equipment.
DMP-BDT460_360_SQT0080_eng.book
12 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Settings
∫ About the wireless connection
The following settings can be performed anytime
in the Setup menu (&gt; 26, 27).
Easy Settings
To obtain your network name (SSID*) and
encryption key (password).
e.g.
The default settings may be
After connecting your new player for the first time
and pressing [&Iacute;], the basic settings screen will
appear.
printed on the router. If the SSID
and password have been
changed, consult the person
responsible for setting up your
network.
Preparation
Turn on the TV and select the appropriate
video input.
For more details, refer to the
manual supplied with the wireless broadband
router, or contact your Internet provider.
1
For more information or assistance, refer to
http://www.panasonic.com/support
(U.S. customers only)
Press [&Iacute;].
Setup screen appears.
2
Follow the on-screen instructions to
continue with the settings.
SSID XXXXXXXXXXXX
KEY XXXXXXXXXXXX
PIN XXXXXXXXX
If your SSID is not displayed;
Search again by pressing the red button on the
remote control.
Wireless Settings
Easy Network Setting
After completing “Easy Settings”, you can perform
“Easy Network Setting”.
Select “Wired” or “Wireless” and press [OK].
Easy Network Setting
Select a connection mode.
Select a wireless network for connection.
Press the green button to connect via
WPS (PUSH button method).
SSID
Search again
OK
OPTION
Wired
Wireless
OK
RETURN
Follow the on-screen instructions to establish
your connection settings.
Reception
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
WPS (PUSH)
RETURN
Stealth SSIDs will not be displayed; in this case,
enter manually in the following order.
1 To display the SSID input screen :
Press [HOME]
&gt; select [OK] to select “Setup”
&gt; select “Player Settings”
&gt; select “Network” and press [OK]
&gt; select “Network Settings” and press [OK]
&gt; select “Wireless Settings” and press [OK]
&gt; select “Connection Setting” and press [OK]
&gt; select “Manual setting” and press [OK]
2 Enter your SSID.
≥ If your wireless network is encrypted, go to
page 13.
If your wireless router supports WPS (Wi-Fi
Protected SetupTM);
You can easily set up a connection by pressing
the green button on the remote control.
12
SQT0080
13 ページ ２０１３年１２月１９日　木曜日　午後３時０分
If your wireless network is encrypted;
Enter your encryption key (password).
≥ You can switch between capital and lower case
letters by pressing the “Shift” key.
Encryption Key (Password)
l
Shift
1
2
3
4
5
6
7
8
9
0
Delete
Finish
.
Space
/
Symbols
:
~
_
-
@
*
#
;
`
“
,
Alphanumeric
Other Characters
Firmware updates
Occasionally, Panasonic may release updated
firmware for this unit that may add or improve the
way a feature operates. These updates are
available free of charge.
This unit is capable of checking the firmware
automatically when connected to the Internet via
a broadband connection.
When a new firmware version is available, the
following message is displayed.
Firmware Update
OK
RETURN
'PVGT
ECUGUGPUKVKXG
New Version:
X.XX
Current Version: X.XX
Do you want to start firmware update?
For the update information, please visit the
following website:
http://panasonic.net/support/
≥ Refer to the owner’s manuals of the hub or router.
≥ Do not use this unit to connect to any wireless network for
which you do not have usage rights.
Using these networks may be regarded as illegal
access.
≥ If you have trouble getting online on your PC after
performing network settings on this unit, perform the
network settings on your PC.
≥ Please be aware that connecting to a network without
encryption may result in the leaking of data such as
personal or secret information.
* SSID:
An SSID (Service Set IDentification) is a name used by
wireless LAN to identify a particular network.
Transmission is possible if the SSID matches for both
devices.
Yes
No
OK
RETURN
DO NOT DISCONNECT the unit from the AC
power or perform any operation while the update
takes place.
After the firmware is installed, “FIN” will be
displayed on the unit’s display. Unit will restart
and the following screen will be displayed.
The firmware was updated.
Current Version: x.xx
RETURN
≥ If downloading on this unit fails or this unit is not
connected to the Internet, then you can download the
latest firmware from the following website and burn it
to a CD-R to update the firmware.
http://panasonic.jp/support/global/cs/
(This site is in English only.)
To show the firmware version on this unit.
(&gt; 29, “Firmware Version Information”)
≥ Downloading will require several minutes. It may take
longer or may not work properly depending on the
connection environment.
≥ If you do not want to check for the latest firmware version,
set “Automatic Update Check” to “Off”. (&gt; 29)
SQT0080
13
Connections and Settings
DMP-BDT460_360_SQT0080_eng.book
DMP-BDT460_360_SQT0080_eng.book
14 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Inserting or removing
media
Playback
SD CARD
Notes
≥ When inserting a media item, ensure that it is
facing the correct way, which is the right side
facing up.
≥ When removing the SD card, press the center
of the card and pull it straight out.
≥ If you connect a Panasonic product with a USB
connection cable, the setup screen may be
displayed on the connected equipment. For
details, refer to the instructions for the
connected equipment.
CAUTION
Do not place objects in front of the unit. The disc
tray may collide with objects when it is opened,
and this may cause malfunction.
14
SQT0080
DMP-BDT460_360_SQT0080_eng.book
15 ページ ２０１３年１２月１９日　木曜日　午後３時０分
HOME menu
Videos/Photos/Music
Major functions of this unit can be operated from
the HOME menu.
Disc
Preparation
Turn on the TV and select the appropriate video
input.
USB
Press [&Iacute;] to turn on the unit.
≥ After network service introduction banner is
shown, the HOME menu is displayed.
–When connected to the network, the
banner content may be changed.
–You can disable the “Start-up Banner”
(&gt; 28).
2
Press [OK] or [3, 4, 2, 1] to select the item.
≥ If there are any other items, repeat this
step.
Network
Network
Service
Home
Network
Displays the Home Screen of
Network Service. (&gt; 19)
DLNA Client (&gt; 20)
Miracast (&gt; 20)
Media Renderer (&gt; 21)
Setup
Player
Settings
(&gt; 24)
USB
(&gt; 18)
Management
HOME
Network
Blu-ray Disc Player
Photos
Setup
Wallpaper
Music
Changes the background of
HOME menu.
To show the HOME menu
Press [HOME].
Videos
Setup
Personalize
1st user
≥ Items to be displayed may vary with the media.
≥ Where necessary, set “Mixed Data Disc Option” when
using a disc with both data files (MP3, JPEG, MKV, etc.)
and Video (BDAV and AVCHD). (&gt; 28)
SQT0080
15
Playback
1
SD Card
Play back the contents. (&gt; 17)
≥ When multiple contents are
recorded, select the types of
contents or the title.
DMP-BDT460_360_SQT0080_eng.book
16 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Multi User Mode
Multi User Mode allows individuals to customize
settings and switch to their saved settings easily.
Up to four people can use the unit with their own
settings.
The following settings can be personalized:
≥ The user icon
≥ The wallpaper of HOME menu
≥ The specific settings (&gt; 22, 24)
A
1
Press [HOME].
2
Press the colored button that indicates
new user personalization.
3
Select an item and change the settings
according to the indications.
The following items can be set.
Input
Nickname
HOME
User 1
Network
Blu-ray Disc Player
Personalizing a new user
Personalize a user name.
Personalize a user icon.
Photos
Setup
Music
Videos
Setup
User 1
B
Select Icon
Personalize
2nd user
Select from Illustrations
The image can be selected from
prepared illustrations.
Create from Photos
You can select a photo in
recording media as an icon.
(&gt; 23, “Icon Personalization”)
A The user name and icon currently selected
B Personalize a new user and switch between
users with colored buttons.
Select
Wallpaper
4
Personalize a background of the
HOME menu.
≥ In addition to the default
wallpapers, you can select a
photo in recording media as a
wallpaper. (&gt; 23, “Wallpaper”)
Select “Confirm” and press [OK].
To change the personalized user information
Select “Edit User Information” from Setup menu.
(&gt; 28)
Switching the user
information
Press the colored buttons in the HOME menu
to switch to the user information
corresponding to the button.
16
SQT0080
17 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Playback
1
2
Search/Slow motion
Playback starts depending on the media.
Search
While playing, press [SEARCH6] or
[SEARCH5].
Select the item to play and press [OK].
Slow motion
While paused, press [SEARCH5].
Insert the media.
Repeat this step if necessary.
≥ DISCS CONTINUE TO ROTATE WHILE MENUS ARE
DISPLAYED. Press [∫STOP] when you have finished
playback to protect the unit’s motor, your TV screen and so
on.
≥ [BDT460]: When the following conditions are met, a still
picture will be played back in 4K. The resolution of the still
picture will be changed automatically.
– The unit is connected to a 4K compatible TV
– “HDMI Resolution” is set to “Auto” (&gt; 24)
– The still picture is being played back in 2D
≥ It is not possible to play back AVCHD and MPEG2 videos
which have been dragged and dropped or copied and
pasted to the media.
≥ To save on electricity, this unit is turned off automatically if
there is no button operation for about 30 minutes when not
playing back (such as when paused or displaying the
menu, displaying still pictures, etc.). (Compatible with
ENERGY STAR SPECIFICATIONS)
Operations during playback
The following functions may not work depending
on the media and contents.
Stop
Press [∫STOP].
The stopping point is memorized.
Resume play function
Press [1PLAY] to restart from this point.
≥ The point is cleared if the media is removed.
≥ On BD-Video discs including BD-J, the
resume play function does not work.
The speed increases up to 5 steps.
≥ Music, MP3, etc.: The speed is fixed to a single
step.
≥ Press [1PLAY] to revert to normal playback
speed.
Skip
While playing or paused, press [:] or
[9].
Skip to the title, chapter or track.
Frame-by-frame
While paused, press [1] (;1).
≥ Press and hold to fast forward.
≥ Press [1PLAY] to revert to normal playback
speed.
Playback
DMP-BDT460_360_SQT0080_eng.book
Changing audio
Press [AUDIO].
You can change the audio channel number or
soundtrack language, etc.
Show top menu/pop-up
menu
Press [POP-UP MENU/TOP MENU].
≥ Select the item and press [OK].
Pause
Press [;PAUSE].
≥ Press [;PAUSE] again or [1PLAY] to restart
play.
SQT0080
17
DMP-BDT460_360_SQT0080_eng.book
18 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Show the status messages
While playing, press [STATUS].
The status messages give you information about
what is currently being played. Each time you
press [STATUS], the display information may
change or disappear from the screen.
≥ Depending on media and contents, the display
may change or not appear.
e.g., BD-Video
C1
1
Perform network connection and settings.
(&gt; 11, 12)
2
Connect a USB device with 1 GB or more
free space.
≥ The USB device is used as the local storage.
3
Insert the disc.
BD-Video
0:05.14
Play
0:20.52
C
A
B
C
D
With “BD-Live” discs, you can enjoy bonus
contents that use Internet access.
For this BD-Live function, connection of a USB device
is necessary along with Internet connection.
B
A
T1
Enjoying BD-Live
D
T: Title, C: Chapter, PL: Playlist
Elapsed time in the title
Current position
Total time
e.g., JPEG
Date
Size
Manufacturer
Equipment
11/12/2007
500 X 375
1 / 26
Enjoying 3D video and
photos
Preparation
Connect this unit to a 3D compatible TV. (&gt; 9)
≥ Perform the necessary preparations for the TV.
≥ Play back following the instructions displayed
on the screen.
≥ 3D Settings (&gt; 23, 26)
∫ Deleting data on the USB device
Select “USB Management” in the HOME menu
(&gt; 15), then select “BD-Video Data Erase” and
press [OK].
≥ The usable functions and the operating method may vary
with each disc, please refer to the instructions on the disc
and/or visit their website.
≥ “BD-Live Internet Access” may need to be changed for
certain discs (&gt; 27).
Slideshow
Play a slideshow of photos and adjust various
settings during the playback.
1
Insert the media.
2
Select “Photos”.
3
Select an item and press the green button.
The following items can be set.
≥ Please refrain from viewing 3D images if you do not feel
well or are experiencing visual fatigue.
In the event that you experience dizziness, nausea, or
other discomfort while viewing 3D images, discontinue use
and rest your eyes.
≥ 3D video might not output the way it is set in “HDMI
Resolution” and “24p(4K)/24p Output”. (&gt; 24)
≥ When playing back 3D photos from “Photos” screen, select
from the “3D” list. (Still pictures in “2D” are played back in
2D.)
If “2D” and “3D” indications are not displayed, press the red
button on the remote control to switch the view of playback
contents.
Start
Slideshow
Start the slideshow.
You can display still pictures in
the selected folder one by one at
a constant interval.
Display
Interval
Change the display interval.
Transition
Effect
Select the effect when sliding
pictures.
Repeat Play Set whether to repeat the slideshow.
≥ Still pictures displayed as “
with this unit.
18
SQT0080
” cannot be played back
19 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Network Service
(Enjoying Netflix, etc.)
Network Service allows you to access some
specific websites supported by Panasonic.
≥ Some services, such as Netflix require a
registered account.
For details of your Netflix account, refer to
Netflix.
Network Service provides a variety of
selected Internet services such as the
following.
≥ Online movie rental service
≥ Video browsing service
XXXXX
XXXXX
X
*
XXXXXXXXXXXXXXXXXXXX
XXXXXXXX
XXXXXX
Featured Videos
MORE
XXXXXXXXXXX
XXXXXXXX
BACK
Market
XXXX
XXXX
≥ When playing content in the media, Network Service
cannot be accessed by pressing [INTERNET].
≥ In the following cases, settings are possible using the
Setup menu items.
– When restricting the use of Network Service
(&gt; 27, “Network Service Lock”)
– When correcting the displayed time
(&gt; 27, “Time Zone”, “DST”)
– When using another device such as a smartphone in
combination with the unit by using a certain app on the
device
(&gt; 27, “Remote Device Operation”)
≥ When using a slow Internet connection, the video may not
be displayed correctly. A high speed Internet service with a
speed of at least 6 Mbps is recommended.
≥ Be sure to update the firmware as soon as a firmware
update notice is displayed on the screen. If the firmware is
not updated, you may not be able to use Network Service
function properly. (&gt; 13)
≥ Network Service Home Screen is subject to change
without notice.
≥ The services through Network Service are operated by
their respective service providers, and service may be
discontinued either temporarily or permanently without
notice. Therefore, Panasonic will make no warranty for the
content or the continuity of the services.
≥ Some features of websites or content of the service may
not be available.
≥ Some content may be inappropriate for viewers.
≥ Some content may only be available for specific countries
and may be presented in specific languages.
Playback
DMP-BDT460_360_SQT0080_eng.book
Internet
* Images are for illustration purposes, contents may change
without notice.
Preparation
≥ Network connection (&gt; 11)
≥ Network settings (&gt; 12)
1
Press [INTERNET].
≥ Netflix can be accessed directly by pressing
[NETFLIX] button.
2
Select the item and press [OK].
To exit from Network Service
Press [HOME].
SQT0080
19
DMP-BDT460_360_SQT0080_eng.book
20 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Home Network feature
Playing back contents on
the DLNA server
Before using the following features, be sure to
configure the connected equipment on your
Home Network.
Using MiracastTM
You can enjoy the content you are viewing on a
Miracast-compatible smartphone, etc. on the big
screen of your TV.
≥ Compatible with AndroidTM devices, ver. 4.2 and
above and Miracast certified.
For information on whether the smartphone,
etc. supports Miracast, contact the
manufacturer of the device.
Player
Miracast
compatible device
1
Press [MIRACAST].
2
Operate the Miracast compatible device.
≥ On the device, enable Miracast and select
this unit (DMP-BDT460 or DMP-BDT360)
as the device to be connected.
For details, refer to the instructions supplied
with the device.
[BDT361] With the default setting, the unit
name will be displayed as “DMP-BDT361”.
To exit from Miracast
Press [HOME].
You can share photos, videos and music stored in
the DLNA Certified media server (PC with
Windows 7 installed, smartphone, etc.) connected
to your home network.
≥ About support format of DLNA (&gt; 35).
Server
Player
Preparation
1 Perform network connection (&gt; 11) and
network settings (&gt; 12) of this unit.
2 Add the contents and folder to the libraries of
the Windows Media&reg; Player or the
smartphone, etc.
≥ Playlist of Windows Media&reg; Player can play
back only the contents that are stored in the
libraries.
1
2
3
4
Press [HOME].
Select “Network”.
Select “Home Network”.
Select “DLNA Client”.
≥ The list can be updated by pressing the red
button on the remote control.
≥ The connection method can be switched to
Wi-Fi Direct by pressing the green button
on the remote control.
5
6
Select the equipment and press [OK].
Select the item to play and press [OK].
≥ You may be able to use convenient
functions depending on the content by
pressing [OPTION].
To exit from Home Network
Press [HOME].
20
SQT0080
DMP-BDT460_360_SQT0080_eng.book
21 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Using the Digital Media
Controller
You can use a smartphone or tablet as the Digital
Media Controller (DMC) to playback contents
from DLNA server on the Renderer (this unit).
Possible applications:
Server
Renderer
*
Controller *
Server
Renderer
About DLNA and Media renderer
For more details, refer to the following website
and the owner’s manuals for each of the
equipment.
http://panasonic.jp/support/global/cs/
(This site is in English only.)
≥ Wi-Fi Direct connection while using Home Network feature
is only temporary, and the network connection method
returns to the original setting when exiting.
≥ Depending on the device or connection environment, the
data transfer rate may decrease.
≥ Depending on the contents and the connected equipment,
playback may not be possible.
≥ Items displayed in gray on the display cannot be played
back by this unit.
*
+
Controller
* DMC compatible software should be installed.
1
2
3
4
5
Press [HOME].
6
Operate the DMC compatible devices.
Playback
Preparation
Perform steps 1 and 2. (&gt; 20)
3 Perform the “Remote Device Settings”.
(&gt; 27)
≥ You can register up to 16 devices.
Select “Network”.
Select “Home Network”.
Select “Media Renderer”.
Select “Home Network” or “Wi-Fi Direct”
and press [OK], then follow the indications
on the screen.
To exit from Media Renderer screen
Press [HOME].
SQT0080
21
DMP-BDT460_360_SQT0080_eng.book
22 ページ ２０１３年１２月１９日　木曜日　午後３時０分
“HDMI CEC”
This unit supports “HDMI CEC” (Consumer
Electronics Control) function.
You can use this function by connecting the
equipment with an HDMI cable*. See the
owner’s manuals for connected equipment for
operational details.
* [BDT460] : Only when connecting via an HDMI AV OUT
MAIN terminal on this unit.
Preparation
1 Set “HDMI CEC” to “On” (&gt; 28). (The default
setting is “On”.)
2 Set the “HDMI CEC” operations on the
connected equipment (e.g., TV).
3 Turn on all “HDMI CEC” compatible
equipment and select this unit’s input channel
on the connected TV so that the “HDMI CEC”
function works properly.
Repeat this procedure when the
connections or settings are changed.
Option menu
Settings
A variety of playback operations and settings can
be performed from this menu.
Available options differ depending on the playing
contents and the condition of the unit.
About Multi User Mode
: Settings of the items with this indication are
saved by the respective users registered in the
HOME menu. (&gt; 16)
1
Press [OPTION].
≥ When playing music, select “Playback
Settings” and press [OK].
e.g., BD-Video
Operation Menu
Soundtrack
1ENG DTS-HD MSTR ...
Subtitle
Angle
Off
Repeat Play
Status
Primary Video
MPEG-4 AVC
Secondary Video
Zoom
Top Menu
Pop-up Menu
Automatic input switching
Power on link
When the unit starts playback, the TV will
automatically switch the input channel and the
screen of the unit will be displayed.
Additionally when the TV is off, the TV will
automatically turn on.
Closed Caption
2
Select an item and change the settings.
To exit the screen
Press [OPTION].
Regarding Language : (&gt; 35)
Operation Menu
Power off link
∫ Soundtrack
Show or change the soundtrack.
All connected equipment compatible with “HDMI
CEC”, including this unit, automatically turns off
when you switch the TV off.
∫ Audio channel
Select the audio channel number.
∫ Subtitle
Change the subtitle settings.
≥ This unit supports the “HDMI CEC” (Consumer Electronics
Control) function. However, operation cannot be
guaranteed on all HDMI CEC devices.
∫ Angle
Select the number of the angle.
∫ Repeat Play
Select the item that you want to repeat.
≥ You can repeat the playback of a chapter,
playlist, the entire disc, etc., but the items
displayed will differ depending on the type of
the media.
≥ Select “Off” to cancel.
22
SQT0080
23 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Select whether or not to play random.
∫ Start Slideshow
Start the slideshow.
∫ Status
Show the status messages.
∫ Rotate Right
∫ Rotate Left
Rotate the still picture.
∫ Wallpaper
Set the still picture to the wallpaper of HOME
menu. (&gt; 15)
∫ Icon Personalization
Set the still picture as your user icon. (&gt; 16)
∫ Video
The recording method of original video appears.
∫ Primary Video
The recording method of original primary video
appears.
∫ Secondary Video
Video
Soundtrack
Select on/off for images. The
recording method of original
video appears.
≥ During search/slow motion or
frame-by-frame, only the
primary video is displayed.
Select on/off for audio and the
language.
Video Settings
∫ Picture Mode
Select the picture quality mode during play.
≥ If you select “User”, you can change settings in
“Picture Adjustment”.
∫ Picture Adjustment
Specific picture quality settings can be changed.
∫ Progressive
Select the method of conversion for progressive
output to suit the type of material being played.
≥ When the content is distorted, change the
settings from “Auto” to “Video”.
∫ 24p
Movies and other material recorded on
DVD-Video at 24p are output at 24p.
≥ Only when you have selected “24p(4K)” or
“24p” in “24p(4K)/24p Output” (&gt; 24).
∫ Reset to Default Video Settings
Return video settings to the factory defaults.
Playback
∫ Shuffle
3D Settings
∫ Signal Format
Original
Keep original picture format.
Side by side
3D picture format comprising of
left and right screens.
2D to 3D
Converts 2D pictures to 3D
effect.
∫ Zoom
Videos and pictures are magnified.
∫ Distance
Set the amount of depth perception.
∫ Top Menu
Display Top Menu.
∫ Pop-Out Level
3D position for the Option menu or message
screen, etc. can be adjusted during 3D playback.
∫ Pop-up Menu
Display Pop-up Menu.
∫ Menu
Display Menu.
∫ Closed Caption
(&gt; 26)
You can only set “Manual setting” and “CC Reset”
in the Setup menu.
SQT0080
23
Settings
DMP-BDT460_360_SQT0080_eng.book
DMP-BDT460_360_SQT0080_eng.book
24 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Setup menu
Change the unit’s settings if necessary. The
settings remain intact even if you switch the unit
to standby.
Some items are common to the Option menu. You
can get the same effect with both menus.
About Multi User Mode
: Settings of the items with this indication are
saved by the respective users registered in the
HOME menu. (&gt; 16)
1
Press [HOME].
2
Press [OK] to select “Setup”.
3
Select “Player Settings”.
Player Settings
Picture Mode
Video
Normal
Picture Adjustment
Audio
HDMI Output
3D
Language
Network
Video
∫ Picture Mode
(&gt; 23)
∫ Picture Adjustment
(&gt; 23)
∫ HDMI Output
Press [OK] to show the following settings:
&frac34; HDMI Resolution
The items supported by the connected devices
are indicated on the screen as “&cent;”. When any
item without “&cent;” is selected, the images may be
distorted.
≥ If “Auto” is selected, the best suited output
resolution to the connected TV is
automatically selected.
≥ To enjoy high-definition video up-converted to
1080p, you need to connect the unit directly
to 1080p compatible HDTV (High Definition
TV). If this unit is connected to an HDTV
through other equipment, the other equipment
must also be 1080p compatible.
Ratings
System
OK
RETURN
4
Select an item and change the settings.
To exit the screen
Press [HOME].
&frac34; 24p(4K)/24p Output
This setting is for selecting the output method
for content recorded in 24p*1, such as movies.
24p(4K)
Outputs signals by upconverting
them to 4K*2.
24p
Outputs in 24p.
≥ Connect the compatible TV for each (4K or
1080/24p) output to the HDMI AV OUT MAIN
[BDT460]/HDMI AV OUT [BDT361] [BDT360]
terminal of this unit.
≥ “24p(4K)” works only when playing back in
2D.
≥ When playing DVD-Video, set this setting to
“24p(4K)” or “24p”, and then “24p” in “Video
Settings” (&gt; 23) to “On”.
≥ When BD-Video/DVD-Video images other
than 24p are played, images are output at
60p.
&frac34; HDMI Color Mode
This setting is for selecting color-space
conversion of the image signal.
&frac34; Deep Color Output
This setting is for selecting whether to use Deep
Color Output when a TV that supports Deep
Color is connected.
24
SQT0080
25 ページ ２０１３年１２月１９日　木曜日　午後３時０分
&frac34; Contents Type Flag
Depending on the playback content, the TV will
output adjusting to the optimal method when a
TV that supports this function is connected.
&frac34; HDMI(SUB) Output Mode [BDT460]
Set to output the video from the HDMI AV OUT
SUB terminal or not.
*1
*2
A progressive image recorded at a rate of 24 frames per
second (motion-picture film). Many BD-Video movie
contents are recorded in 24 frames/second in accordance
with the film materials.
A high resolution image/display technology of
approximately 4000 (width) k 2000 (height) pixels.
Audio
∫ Dynamic Range Compression
You can listen at low volumes but still hear
dialogue clearly.
(Dolby Digital, Dolby Digital Plus and Dolby
TrueHD only)
≥ “Auto” is effective only when playing Dolby
TrueHD.
∫ Digital Audio Output
Press [OK] to show the following settings:
&frac34; Dolby D/Dolby D +/Dolby TrueHD
&frac34; DTS/DTS-HD
Select the audio signal to output.
≥ Select “PCM”, when the connected
equipment cannot decode the respective
audio format. This unit decodes the audio
format and transmits to the connected
equipment.
≥ If you do not make proper settings the audio
may be static or noisy.
&frac34; BD-Video Secondary Audio
Select whether or not to mix the primary and
secondary audio (including the button click
sound).
If “Off” is selected, the unit outputs the primary
audio only.
&frac34; HDMI Audio Output
This setting selects whether or not to output
audio from HDMI.
≥ Select “Off” when the TV is connected to this
unit via HDMI AV OUT terminal, and this unit
is also connected to other devices, such as
an amplifier/receiver via an OPTICAL
terminal.
∫ PCM Down Conversion
Select how to output audio with a sampling
frequency of 96 kHz for the PCM output from the
OPTICAL.
≥ If “On” is selected, the signals that are
converted to 48 kHz are output.
≥ If “Off” is selected, and the connected
equipment does not support 96 kHz, the sound
will not be output normally.
≥ Signals are converted to 48 kHz despite the
settings in the following cases:
– when the signals have a sampling frequency
of 192 kHz
– when the disc has copy protection
– when “BD-Video Secondary Audio” is set to
“On”
∫ Downmix
Select the downmix system of multi-channel to
2-channel sound.
≥ Select “Surround encoded”, when the
connected equipment supports the virtual
surround function.
≥ The downmix effect is not available when
“Digital Audio Output” is set to “Bitstream”.
≥ The audio will be output in “Stereo” in the
following cases:
– AVCHD playback
– Playback of secondary audio (including the
button click sound).
∫ DTS Neo:6
2ch (2.1ch) audio is expanded to 7ch (7.1ch).
≥ This function works when the following
conditions are met:
– Audio is output from the HDMI AV OUT
terminal.
– Audio recorded at 96 kHz or lower is output.
– “Digital Audio Output” is set to “PCM” when
audio other than PCM is output.
SQT0080
25
Settings
DMP-BDT460_360_SQT0080_eng.book
DMP-BDT460_360_SQT0080_eng.book
26 ページ ２０１３年１２月１９日　木曜日　午後３時０分
3D
∫ 3D BD-Video Playback
Select the playback method of 3D compatible
video software.
∫ 3D AVCHD Output
Select the output method of 3D AVCHD videos.
∫ 3D Playback Precautions
Set to display or hide the 3D viewing warning
screen when playing back the 3D compatible
video software.
∫ Pop-Out Level
(&gt; 23)
∫ Closed Caption
Closed captioning services are dependent on
contents, and the unit can display closed captions
of both digital and analog types.
Press [OK] to show the following settings:
&frac34; Closed Caption Display
Set whether or not to display closed captions.
&frac34; Closed Caption Type
Select the closed caption type that matches the
one of the content to be played back.
&frac34; Analog CC
Select the channel of analog closed captions.
&frac34; Digital CC
Language
Select the channel of digital closed captions.
∫ Audio Language
&frac34; Manual setting
Choose the language for audio.
≥ If “Original” is selected, the original language of
each disc will be selected.
≥ Enter a code (&gt; 35) when you select “Other
&cent;&cent;&cent;&cent;”.
Set the display style of closed captions.
∫ Subtitle Language
Choose the language for the subtitle.
≥ If “Auto” is selected and the language selected
for “Audio Language” is not available, subtitles
of that language will automatically appear if
available on that disc.
≥ Enter a code (&gt; 35) when you select “Other
&cent;&cent;&cent;&cent;”.
∫ Menu Language
Choose the language for the disc menus.
≥ Enter a code (&gt; 35) when you select “Other
&cent;&cent;&cent;&cent;”.
∫ Subtitle Text
Select a desired item according to the language
used for MKV/Xvid [For[Canada] subtitles text.
≥ This item is displayed only after playing back a
file.
∫ On-screen Language
Choose the language for menus and on-screen
messages.
26
SQT0080
&frac34; CC Reset
Restore the default “Closed Caption” settings.
Network
∫ Easy Network Setting (&gt; 12)
∫ Network Settings
Perform network-related settings individually.
Press [OK] to show the following settings:
&frac34; LAN Connection Mode
Select the LAN connection method.
≥ Select “Wireless Master” when you make a
direct wireless connection between this unit
and a Home Network device. Internet
connection is not available when this item is
selected.
&frac34; Wireless Settings
This allows the wireless router and connection
settings to be set up. Current connection
settings and connection state can be checked.
Press [OK] to show the following settings:
Connection Setting
The wireless router connection wizard will be
displayed.
27 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Double Speed Mode Setting (2.4GHz)
Set the connection speed for a 2.4 GHz
wireless format.
≥ If you connect using the “Double Speed
Mode (40MHz)”, 2 channels use the same
frequency band, and there is consequently
a greater risk of reception interference. This
can cause the connection speed to drop or
become unstable.
&frac34; IP Address/DNS Settings
This is for checking the state of the network
connection and setting the IP address and
DNS-related.
Press [OK] to show the respective setting.
&frac34; Proxy Server Settings
This is for checking the state of connection with
the Proxy server and performing settings.
Press [OK] to show the respective setting.
&frac34; Network Service Settings (&gt; 19)
Press [OK] to show the following settings:
Time Zone
Set the unit’s time to match your location.
≥ Some Network Service contents require the
time zone to be set. Set time zone if
necessary.
DST
Select “On” when using Daylight Saving time.
&frac34; Network Drive Connection
It is possible to access the shared folder of
equipment not compatible with DLNA, such as
the Windows XP operating system, and play
back video, still pictures, and music on this unit.
For the setting and operation method of
connected equipment, refer to the following
website.
http://panasonic.jp/support/global/cs/
(This site is in English only.)
&frac34; Remote Device Settings (&gt; 19, 21)
Press [OK] to show the following settings:
Remote Device Operation
Enable to operate the unit by DMC, etc.
≥ If “On” is selected, “Quick Start” will be
activated.
Setting Unit Name
Set the name of this unit to be displayed on
the connected equipment.
Registration Type
Auto
Allow connections to all the
equipment accessing this unit.
Manual
Set the permission for
individual equipment
connections accessing this
unit.
Remote Device List
Registering/deregistering of the displayed
equipment can be performed when “Manual”
in “Registration Type” is selected.
&frac34; BD-Live Internet Access (&gt; 18)
You can restrict Internet access when BD-Live
functions are used.
≥ If “Allow ( Limited )” is selected, Internet
access is permitted only for BD-Live contents
which have content owner certificates.
Ratings
The following items use the same password.
Don’t forget your password.
∫ DVD-Video Ratings
Set a ratings level to limit DVD-Video play.
∫ BD-Video Ratings
Set an age limit of BD-Video play.
∫ Network Service Lock
You can restrict the usage of Network Service.
System
∫ Easy Settings
You can execute basic settings.
∫ Display Settings
Press [OK] to show the following settings:
SQT0080
27
Settings
DMP-BDT460_360_SQT0080_eng.book
DMP-BDT460_360_SQT0080_eng.book
28 ページ ２０１３年１２月１９日　木曜日　午後３時０分
&frac34;TV Aspect
&frac34; Mixed Data Disc Option
Set to match the type of TV connected.
Select the playback contents on discs with both
data files and Video.
≥ If “MP3/JPEG/MKV” is selected, data file can
be played back.
≥ If “BDAV/AVCHD” is selected, BDAV and
AVCHD can be played back.
When connected to a 4:3 aspect TV and playing
16:9 ratio image:
The sides are cut
off so the picture
4:3 Pan &amp; fills the screen.
Scan
When playing
BD-Video, video is output as “4:3
Letterbox”.
Black bands
4:3
appear at the top
Letterbox and bottom of the
picture.
When connected to a 16:9 widescreen TV and
playing 4:3 ratio image:
16:9
Video is displayed as a 4:3 ratio
image in the center of the
screen.
16:9 Full
Video is displayed as a
horizontally stretched 16:9
image.
&frac34;Screen Saver Function
This is to prevent image retention on the
screen.
≥ When this is set to “On”:
If a list of playback content is displayed and
there is no operation for 10 minutes or more,
the screen switches to HOME menu
automatically.
≥ While playing and pausing, etc., this function
is not available.
&frac34; Front Panel Display
Changes the brightness of the unit’s display.
≥ If “Auto” is selected, the display is set to bright
and only dimmed during playback.
&frac34; Blue LED [BDT460] [BDT361/360_for_U.S.A.]
Set whether to light the blue LED in the center
of this unit when turned ON.
&frac34; HDMI(SUB) V.OFF LED Control [BDT460]
Set to light the HDMI (SUB) V.OFF LED or not.
≥ This will light when “HDMI(SUB) Output
Mode” (&gt; 25) is set to “V.OFF”.
&frac34; Edit User Information
Change the user information registered in the
HOME menu.
∫ Start-up Banner
Select whether to display the banner after turning
on this unit. (&gt; 15)
∫ Quick Start
Speed of start-up from standby mode is
increased.
≥ When set to “On”, the internal control unit will be
powered and the idle power consumption will
increase so compared to when set to “Off”.
(Power consumption &gt; 34)
&frac34;Status Messages
∫ Remote Control Code
Choose whether to show status messages
automatically.
Change the remote control code if other
Panasonic products react to this remote control.
&frac34;HDMI CEC
Set to use “HDMI CEC” function when
connected via HDMI cable to a device that
supports “HDMI CEC”.
≥ Select “Off” when you do not want to use
“HDMI CEC”.
∫ Firmware Update (&gt; 13)
∫ Unit Settings
Press [OK] to show the following settings:
28
SQT0080
Press [OK] to show the following settings:
DMP-BDT460_360_SQT0080_eng.book
29 ページ ２０１３年１２月１９日　木曜日　午後３時０分
&frac34; Automatic Update Check
When this equipment remains connected to the
Internet, it will check for the latest firmware
version when it is turned on and you can update
it if necessary.
&frac34; Update Now
You can update the firmware manually if a
firmware update is available.
∫ System Information
Press [OK] to show the following settings:
&frac34; License
Information about the software used by this unit
is displayed.
&frac34; Firmware Version Information
Display firmware version of this unit and
wireless LAN module.
Settings
∫ Restore Default Settings
This returns all values in the Setup menu and the
Option menu to the default settings, except for
some settings of network, ratings, remote control
code, on-screen language, etc.
SQT0080
29
DMP-BDT460_360_SQT0080_eng.book
30 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Troubleshooting guide
Reference
Before requesting service, please perform the
following steps.
∫ Unit does not respond to remote
control or unit’s buttons.
Disconnect AC power supply cord, wait 1 minute,
then reconnect AC power supply cord.
Do you have the latest firmware installed?
Panasonic is constantly improving the unit’s
firmware to ensure that our customers are
enjoying the latest technology. (&gt; 13)
4
Make the following checks and visit our
website for more information.
For U.S.A. :
www.panasonic.com/support
Enter the model number.
For Canada :
http://www.panasonic.ca
4
Or visit our website to find a service center.
You can find a service center near you easily
on our website.
Other support information:
“Customer Services Directory (United States
and Puerto Rico)” (&gt; 37) or “CONTACT
INFORMATION” (&gt; 38).
The following do not indicate a problem with
this unit:
– Regular disc rotating sounds.
– Image disturbance during search.
– Image disturbance when replacing 3D discs.
∫ Cannot eject disc.
1 Turn the unit on.
2 Press and hold [OK], the yellow button and
the blue button on the remote control at the
same time for more than 5 seconds.
– “00 RET” is displayed on the unit’s display.
3 Press [1] (right) repeatedly on the remote
control until “06 FTO” is displayed on the
unit’s display.
4 Press [OK].
30
SQT0080
General operation
To return to the factory defaults.
&frac34; Select “Yes” in “Restore Default Settings” in
the Setup menu. (&gt; 29)
To return all settings to the factory preset.
&frac34; Reset the unit as follows:
1 Turn the unit on.
2 Press and hold [OK], the yellow button and
the blue button on the remote control at the
same time for more than 5 seconds.
– “00 RET” is displayed on the unit’s display.
3 Press [1] (right) repeatedly on the remote
control until “08 FIN” is displayed on the unit’s
display.
4 Press and hold [OK] for more than 5 seconds.
The remote control does not work properly.
&frac34; Change the batteries in the remote control.
(&gt; 5)
&frac34; The remote control and this unit are using
different codes. If “SET ” is displayed on the
unit’s display when a button is pressed on the
remote control, change the code on the
remote control.
Press and hold [OK] and the displayed
number (“”) for at least 5 seconds.
The TV tuner mode is not displayed when the
TV is turned on.
&frac34; This phenomenon may occur, depending on
the TV setting, when “Quick Start” is set to
“On”.
&frac34; Depending on the TV, this phenomenon may
be prevented by reconnecting the HDMI cable
to a different HDMI input terminal or by
changing the HDMI auto connection setting.
You have forgotten your ratings password.
You want to cancel the ratings level.
&frac34; The ratings level returns to the factory
defaults.
1 Turn the unit on.
2 Press and hold [OK], the yellow button and
the blue button on the remote control at the
same time for more than 5 seconds.
– “00 RET” is displayed on the unit’s display.
3 Press [1] (right) repeatedly on the remote
control until “03 VL” is displayed on the unit’s
display.
4 Press [OK].
31 ページ ２０１３年１２月１９日　木曜日　午後３時０分
The TV screen turns black.
&frac34; In the following cases, HDMI authentication
takes place and a black screen is displayed:
– When “24p Output” is set to “On”.
– When the display is switched between 2D
and 3D images.
– [BDT460] : When you quit the 4K playback of
a still picture by displaying another screen,
including the Home menu.
This unit does not recognize the USB
connection correctly.
&frac34; Disconnect and re-connect the USB cable. If
it still does not recognize the connection, turn
this unit off and on again.
&frac34; USB devices may not be recognized by this
unit when connected using the following :
– a USB hub
– a USB extension cable
&frac34; If you connect USB HDD to this unit, use the
USB cable that is supplied with the HDD.
Picture
The images from this unit do not appear on
the TV.
Picture is distorted.
&frac34; An incorrect resolution is selected in “HDMI
Resolution”. Reset the setting as follows:
1 Turn the unit on.
2 Press and hold [OK], the yellow button and
the blue button on the remote control at the
same time for more than 5 seconds.
– “00 RET” is displayed on the unit’s display.
3 Press [1] (right) repeatedly on the remote
control until “04 PRG” is displayed on the
unit’s display.
4 Press and hold [OK] for more than 5 seconds.
Set the item again. (&gt; 24)
– When Dolby Digital Plus, Dolby TrueHD,
and DTS-HD&reg; audio are not output properly,
select “Yes” in “Restore Default Settings”
(&gt; 29) and make proper settings.
&frac34; When “3D BD-Video Playback” in the Setup
menu is set to “Auto”, images may not be
output depending on the connection method.
After removing the disc from this unit, select
“Set before play” in the Setup menu, and
select “2D Playback” in the setup screen
displayed when playing 3D discs. (&gt; 26)
&frac34; When outputting in 24p (4K), images may be
distorted depending on the HDMI cable. Use
an HDMI cable that supports 4K output.
Video is not output. [BDT460]
&frac34; Video from the HDMI AV OUT SUB terminal is
not output when the “HDMI(SUB) Output
Mode” is set to “V.OFF”. (&gt; 25)
Video is not output in high-definition.
&frac34; Confirm that “HDMI Resolution” in the Setup
menu is set properly. (&gt; 24)
3D video is not output.
&frac34; Connect to a full high-definition TV.
&frac34; Is there a non-3D compatible amplifier/
receiver connected between this unit and a
TV? (&gt; 9)
&frac34; [BDT460] : If there is a non-3D compatible
amplifier/receiver connected to the HDMI AV
OUT SUB terminal, set the “HDMI(SUB)
Output Mode” to “V.OFF”. (&gt; 10)
&frac34; Are the settings on this unit and the TV
correct? (&gt; 18)
&frac34; Is the amplifier/receiver that is connected
between this unit and TV on?
&frac34; Depending on the connected TV, the video
being played back might switch to 2D video
due to changes in resolution etc. Check the
3D setting on the TV.
3D video is not output correctly as 2D.
&frac34; Select “Set before play” in the Setup menu,
and select “2D Playback” in the setup screen
displayed when playing 3D discs. (&gt; 26, “3D
BD-Video Playback”)
&frac34; Discs that have recorded titles with Side by
side (2 screen structure) and that can be
enjoyed in 3D are played back in accordance
with the settings of the TV.
No subtitles.
&frac34; When progressive output is on, closed
captions/subtitles cannot be displayed.
The subtitles overlap closed captions
recorded on discs.
&frac34; Turn off the subtitles or the closed captions.
(&gt; 22, 26)
Closed captions are not displayed.
&frac34; Confirm that the source content supports CC.
&frac34; Confirm the “Closed Caption Display” is set to
“On”. (&gt; 23, 26)
&frac34; Change the “Closed Caption Type” setting.
(&gt; 23, 26)
&frac34; Confirm the “Analog CC” or “Digital CC” is set
properly (&gt; 23, 26).
SQT0080
31
Reference
DMP-BDT460_360_SQT0080_eng.book
DMP-BDT460_360_SQT0080_eng.book
32 ページ ２０１３年１２月１９日　木曜日　午後３時０分
A black band is displayed around the edge of
the screen.
The aspect ratio of the screen is abnormal.
&frac34; Confirm the “TV Aspect” is set properly.
(&gt; 28)
&frac34; Adjust the aspect setting on the TV.
Audio
Cannot switch audio.
&frac34; The audio cannot switch, if “Digital Audio
Output” is set to “Bitstream”. Set “Digital
Audio Output” to “PCM”. (&gt; 25)
Cannot hear the desired audio type.
&frac34; Check the connections and the “Digital Audio
Output” settings. (&gt; 9, 25)
&frac34; [BDT460] : When connecting this unit to a TV
via an HDMI AV OUT MAIN and to an
amplifier/receiver via an HDMI AV OUT SUB,
set “HDMI(SUB) Output Mode” to “V.OFF”.
(&gt; 10)
&frac34; To output audio from a device connected with
an HDMI cable, set “HDMI Audio Output” to
“On” in the Setup menu. (&gt; 25)
There is no sound coming out from the TV.
[BDT460]
&frac34; Audio may not output from the TV when the
amplifier/receiver is connected to the HDMI
AV OUT SUB, and “HDMI(SUB) Output
Mode” (&gt; 25) is set to “V.OFF”. In such a
case, output audio from the amplifier/receiver.
To output audio from the TV, set the
“HDMI(SUB) Output Mode” to “Normal”.
Playback
Disc cannot be played.
&frac34; The disc is dirty. (&gt; 5)
&frac34; The disc is not finalized. (&gt; 7)
&frac34; Confirm the “Mixed Data Disc Option” is set
properly. (&gt; 28)
Still pictures (JPEG) do not play back
normally.
&frac34; The images that were edited on the PC, such
as Progressive JPEG, etc., may not be played
back.
32
SQT0080
I can’t play back BD-Live.
&frac34; Confirm that this unit is connected to the
broadband Internet. (&gt; 11)
&frac34; Connect this unit to the network by a wired
connection.
&frac34; Confirm the “BD-Live Internet Access”
settings. (&gt; 27)
&frac34; Confirm a USB device is connected to the
USB port. (&gt; 14)
Network
I can’t connect to the network.
&frac34; Confirm the network connection and settings.
(&gt; 11, 12, 26)
&frac34; There may be interference that prevents the
unit from detecting your home network. Place
the unit and the wireless router closer to each
other. This unit may be able to detect your
network name (&gt; 13, “SSID”).
&frac34; Check the owner’s manuals for each device
and connect accordingly.
When using wireless LAN connection, video
from the DLNA Certified media server is not
played back or video frames are dropped
during playback.
&frac34; Higher transfer rate router such as 802.11n
(2.4 GHz or 5 GHz) wireless router may solve
the problem. If you use 802.11n (2.4 GHz or
5 GHz) wireless router, it is necessary to set
the encryption type to “AES”.
Simultaneous use with a microwave, cordless
telephone etc. at 2.4 GHz may result in
connection interruptions or other problems.
&frac34; On the “Wireless Settings” screen (&gt; 26), the
continuous lighting of at least 4 “Reception”
indicators is the target for a stable connection.
If 3 or fewer indicators are lit or the
connection is being interrupted, change the
position or angle of your wireless router and
see if the connection state improves. If there
is no improvement, connect to a wired
network and perform the “Easy Network
Setting” (&gt; 12) again.
DMP-BDT460_360_SQT0080_eng.book
33 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Messages on the screen
Cannot play.
&frac34; You inserted an incompatible disc (Discs
recorded in PAL video, etc.).
Cannot display on this unit.
&frac34; You tried to play a non-compatible image.
&frac34; Re-insert the media.
No disc inserted.
&frac34; The disc may be upside down.
$ This operation is not available.
&frac34; Some operations are unsupported by the unit.
(For example, reverse slow motion, etc.)
IP address is not set.
&frac34; The “IP Address” in “IP Address/DNS
Settings” is “---. ---. ---. ---”. Set the “IP
Address”, “Subnet Mask”, and “Default
Gateway”. (Select the automatic address
acquisition if necessary.)
The current wireless network security setting
is weak. It is recommended to change to a
stronger security setting.
&frac34; Set a stronger network security level referring
to the wireless router owner’s manuals.
Messages on the unit’s
display
NET
&frac34; While connecting to a network.
No PLAY
&frac34; There is a viewing restriction on a BD-Video
or DVD-Video. (&gt; 27)
&frac34; The media is dirty or badly scratched. The
unit cannot play.
SET (“ ” stands for a number.)
&frac34; The remote control and this unit are using
different codes. Change the code on the
remote control.
Press and hold [OK] and the
indicated number button at
the same time for more than
5 seconds.
U59
&frac34; Temperature of this unit is hot and the unit
switches to standby for safety reasons.
Wait for about 30 minutes.
Install or place this unit with good ventilation.
H or F
(“ ” stands for a number.)
&frac34; There is something unusual.
&frac34; Check the unit using the troubleshooting
guide. If the service number remains
displayed, do the following.
1 Disconnect the plug from the AC outlet, wait a
few seconds, then reconnect it.
2 Press [&Iacute;/I] to turn the unit on.
If the service number remains displayed despite
doing the above, request service from the dealer.
Inform the dealer of the service number when
requesting service.
START
&frac34; The system is being restarted during the
firmware update. Please do not turn off the
unit.
UPD/
(“ ” stands for a number.)
&frac34; The firmware is being updated.
Please do not turn off the unit.
FIN
&frac34; The firmware update is complete.
Reference
REMOVE
&frac34; The USB device is drawing too much power.
Remove the USB device.
SQT0080
33
DMP-BDT460_360_SQT0080_eng.book
34 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Specifications
General
File format
File format
Signal system
NTSC
Operating
temperature range
i5 oC to i35 oC
(i41 oF to i95 oF)
MKV
Operating humidity 10 % to 80 % RH
range
(no condensation)
Digital audio output
Optical digital output
(Optical terminal)
HDMI AV output
Output connector:
[BDT460] Type A (19 pin) 2 system
[BDT361] [BDT360] Type A (19
pin) 1 system
SD card slot
1 system
USB slot
USB2.0:1 system
Ethernet
10BASE-T/100BASE-TX
1 system
Extension
“.MKV”, “.mkv”
Subtitles text
file
“.SRT”, “.srt”,
“.SSA”, “.ssa”,
“.ASS”, “.ass”
“.AVI”, “.avi”
Xvid
Subtitles text
file
[For[Canada] “.SRT”, “.srt”,
“.SUB”, “.sub”,
“.TXT”, “.txt”
mp4
“.MP4”, “.mov”
(H.264+AAC)
MPEG
(TS/PS)
Some mp4/MPEG files
may not be played back
correctly, depending on
“.mpg”, “.mpeg”, the video resolution,
“.m2ts”, “.mts”, frame rate condition and
“.ts”
so on.
JPEG
“.JPG”, “.jpg”,
“.jpeg”
≥ MOTION JPEG and
Progressive JPEG are
not supported.
≥ You may not be able to
play back the file if you
have edited the folder
structure or the file
name on a PC or other
device.
MP3
“.MP3”, “.mp3”
This unit supports ID3
tags, but only titles, artist
names and album names
can be displayed.
FLAC
“.FLAC”, “.flac”
Maximum sampling rate:
192 kHz/24 bit
WAV
“.WAV”, “.wav”
Maximum sampling rate:
192 kHz/24 bit
MPO
“.MPO”, “.mpo”
3D still picture
AAC
“.M4A”, “.m4a”,
“.AAC”, “.aac”
This unit supports ID3
tags.
Maximum sampling rate:
48 kHz/320 kbps
WMA
“.WMA”, “.wma”
This unit supports ID3
tags.
Maximum sampling rate:
48 kHz/355 kbps
Standard Compliance:
IEEE802.11 a/b/g/n
Frequency range:
2.4 GHz/5 GHz band
Wireless LAN
Security:
WPATM/WPA2TM
(Encryption Type: TKIP/AES,
Authentication Type: PSK),
WEP (64 bit/128 bit)
LASER
Specification
Class I LASER Product
Wave length: 785 nm (CDs)/
660 nm (DVDs)/405 nm (BDs)
Laser power: No hazardous
radiation is emitted with the
safety protection
Power supply
AC 120 V, 60 Hz
Power
consumption
Approx. 14 W
Power
consumption in
standby mode
Approx. 0.5 W
Power consumption [BDT460] Approx. 6 W
in quick start standby [BDT361] [BDT360] Approx. 5.5 W
mode
Dimensions
(WkHkD)
Mass (Weight)
Approx. 415 mmk43 mmk182 mm
(Approx. 16 6/16zk1 11/16zk
7 3/16z)
Approx. 1.2 kg (2.65 lbs)
≥ Specifications are subject to change without notice.
34
SQT0080
Reference
≥ The video file and
subtitles text file are
inside the same folder,
and the file names are
the same except for the
file extensions.
≥ Some MKV/Xvid files
may not be played back
correctly, depending on
the video resolution,
frame rate condition,
subtitle format and so
on.
≥ With certain recording states and folder structures, the play
order may differ or playback may not be possible.
35 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Audio information
The audio output differs depending on which
terminals are connected to the amplifier/receiver,
and the settings on the unit. (&gt; 25, “Digital Audio
Output”)
≥ The number of channels listed is the maximum possible
number of output channels when connected to amplifier/
receiver compatible with the respective audio format.
Terminal
Output
channel
*1
*2
“PCM”
HDMI AV Outputs using
OUT*2 original audio*1
BD-Video :
7.1ch PCM*1
DVD-Video :
5.1ch PCM
Dolby Digital/
OPTICAL DTS Digital
SurroundTM
Down-mixed
2ch PCM
When “BD-Video Secondary Audio” is set to “On”, the
audio will be output as Dolby Digital, DTS Digital
SurroundTM or 5.1ch PCM.
When “DTS Neo:6” is set to “Cinema” or “Music”, 2ch
(2.1ch) audio can be expanded to 7ch (7.1ch) and output.
(&gt; 25)
Supported format for DLNA
≥ File formats that are not supported by your
DLNA server cannot be played.
Video
Video
Audio
Example of
Container
codec
codec
file extension
MKV
H.264
.mkv
AAC
MPEG-4
&reg;
DTS
Advanced
PCM
Xvid*
Simple
.avi
FLAC
[For[Canada]
Profile
Vorbis
(ASP)
Dolby Digital
.mts
AVCHD
H.264
MP4
AAC
.mp4, .mov
.mpg,
Dolby Digital
PS
MPEG2
Linear PCM .mpeg
MPEG2
AAC
TS
.m2ts, .ts
Dolby Digital
H.264
Example of file extension
.jpg, .jpeg
Example of file extension
.mp3
.flac
.m4a, .aac
.wma
—
* Only when the file is transcoded by DLNA server.
Display languages list
“Digital Audio Output”
“Bitstream”
Photo
Format
JPEG
Audio
Audio codec
MP3
FLAC
AAC
WMA
Linear PCM
Display Language Display Language Display Language
ENG
FRA
DEU
ITA
ESP
NLD
SVE
NOR
DAN
POR
RUS
English
French
German
Italian
Spanish
Dutch
Swedish
Norwegian
Danish
Portuguese
Russian
JPN
CHI
KOR
MAL
VIE
THA
POL
CES
SLK
HUN
FIN
Japanese
Chinese
Korean
Malay
Vietnamese
Thai
Polish
Czech
Slovak
Hungarian
Finnish
ARA
HIN
PER
IND
MRI
BUL
RUM
GRE
TUR
Arabic
Hindi
Persian
Indonesian
Maori
Bulgarian
Romanian
Greek
Turkish
Others
Language code list
Language
Code Language
Abkhazian:
6566
Afar:
6565
Afrikaans:
6570
Albanian:
8381
Amharic:
6577
Arabic:
6582
Armenian:
7289
Assamese:
6583
Aymara:
6589
Azerbaijani: 6590
Bashkir:
6665
Basque:
6985
Bengali; Bangla:
6678
Bhutani:
6890
Bihari:
6672
Breton:
6682
Bulgarian:
6671
Burmese:
7789
Byelorussian: 6669
Cambodian: 7577
Catalan:
6765
Chinese:
9072
Corsican:
6779
Croatian:
7282
Czech:
6783
Danish:
6865
Dutch:
7876
English:
6978
Esperanto:
6979
Estonian:
6984
Faroese:
7079
Fiji:
7074
Finnish:
7073
French:
7082
Frisian:
7089
Galician:
7176
Georgian:
7565
German:
6869
Greek:
6976
Greenlandic: 7576
Guarani:
7178
Code Language
Gujarati:
7185
Hausa:
7265
Hebrew:
7387
Hindi:
7273
Hungarian:
7285
Icelandic:
7383
Indonesian: 7378
Interlingua:
7365
Irish:
7165
Italian:
7384
Japanese:
7465
Javanese:
7487
Kannada:
7578
Kashmiri:
7583
Kazakh:
7575
Kirghiz:
7589
Korean:
7579
Kurdish:
7585
Laotian:
7679
Latin:
7665
Latvian, Lettish: 7686
Lingala:
7678
Lithuanian:
7684
Macedonian: 7775
Malagasy:
7771
Malay:
7783
Malayalam: 7776
Maltese:
7784
Maori:
7773
Marathi:
7782
Moldavian:
7779
Mongolian:
7778
Nauru:
7865
Nepali:
7869
Norwegian: 7879
Oriya:
7982
Pashto, Pushto: 8083
Persian:
7065
Polish:
8076
Portuguese: 8084
Punjabi:
8065
Quechua:
8185
Code
Rhaeto-Romance:
8277
Romanian:
8279
Russian:
8285
Samoan:
8377
Sanskrit:
8365
Scots Gaelic: 7168
Serbian:
8382
Serbo-Croatian: 8372
Shona:
8378
Sindhi:
8368
Singhalese: 8373
Slovak:
8375
Slovenian:
8376
Somali:
8379
Spanish:
6983
Sundanese: 8385
Swahili:
8387
Swedish:
8386
Tagalog:
8476
Tajik:
8471
Tamil:
8465
Tatar:
8484
Telugu:
8469
Thai:
8472
Tibetan:
6679
Tigrinya:
8473
Tonga:
8479
Turkish:
8482
Turkmen:
8475
Twi:
8487
Ukrainian:
8575
Urdu:
8582
Uzbek:
8590
Vietnamese: 8673
Volap&uuml;k:
8679
Welsh:
6789
Wolof:
8779
Xhosa:
8872
Yiddish:
7473
Yoruba:
8979
Zulu:
9085
SQT0080
35
Reference
DMP-BDT460_360_SQT0080_eng.book
DMP-BDT460_360_SQT0080_eng.book
36 ページ ２０１３年１２月１９日　木曜日　午後３時０分
“AVCHD”, “AVCHD 3D”, “AVCHD Progressive” and “AVCHD 3D/
Progressive” are trademarks of Panasonic Corporation and
Sony Corporation.
Java is a registered trademark of Oracle and/or its affiliates.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby
Laboratories.
For DTS patents, see http://patents.dts.com. Manufactured under
license from DTS Licensing Limited. DTS, DTS-HD, the Symbol, &amp;
DTS and the Symbol together are registered trademarks, and
DTS-HD Master Audio is a trademark of DTS, Inc. &copy; DTS, Inc. All
Rights Reserved.
HDMI, the HDMI Logo, and High-Definition Multimedia Interface
are trademarks or registered trademarks of HDMI Licensing LLC in
the United States and other countries.
This product is licensed under the AVC patent portfolio license and
VC-1 patent portfolio license for the personal and non-commercial
use of a consumer to (i) encode video in compliance with the AVC
Standard and VC-1 Standard (“AVC/VC-1 Video”) and/or (ii)
decode AVC/VC-1 Video that was encoded by a consumer
engaged in a personal and non-commercial activity and/or was
obtained from a video provider licensed to provide AVC/VC-1
Video. No license is granted or shall be implied for any other use.
Additional information may be obtained from MPEG LA, LLC.
See http://www.mpegla.com.
MPEG Layer-3 audio coding technology licensed from Fraunhofer
IIS and Thomson.
SDXC Logo is a trademark of SD-3C, LLC.
“DVD Logo” is a trademark of DVD Format/Logo Licensing
Corporation.
The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi
Alliance.
The Wi-Fi Protected Setup Mark is a mark of the Wi-Fi Alliance.
“Wi-Fi”, “Wi-Fi Protected Setup”, “Wi-Fi Direct”, “Miracast”, “WPA”
and “WPA2” are marks or registered marks of the Wi-Fi Alliance.
DLNA, the DLNA Logo and DLNA CERTIFIED are trademarks,
service marks, or certification marks of the Digital Living Network
Alliance.
Windows is a trademark or a registered trademark of Microsoft
Corporation in the United States and other countries.
Android is a trademark of Google Inc.
This product incorporates the following software:
(1) the software developed independently by or for Panasonic
Corporation,
(2) the software owned by third party and licensed to Panasonic
Corporation,
(3) the software licensed under the GNU General Public License,
Version 2.0 (GPL V2.0),
(4) the software licensed under the GNU LESSER General Public
License, Version 2.1 (LGPL V2.1), and/or
(5) open source software other than the software licensed under
the GPL V2.0 and/or LGPL V2.1.
The software categorized as (3) - (5) are distributed in the hope
that it will be useful, but WITHOUT ANY WARRANTY, without
even the implied warranty of MERCHANTABILITY or FITNESS
FOR A PARTICULAR PURPOSE. Please refer to the detailed
terms and conditions thereof shown in the Player Settings menu.
At least three (3) years from delivery of this product, Panasonic will
give to any third party who contacts us at the contact information
provided below, for a charge no more than our cost of physically
performing source code distribution, a complete machine-readable
copy of the corresponding source code covered under GPL V2.0,
LGPL V2.1 or the other licenses with the obligation to do so, as
well as the respective copyright notice thereof.
Contact Information: [email protected]
The source code and the copyright notice are also available for
free in our website below.
http://panasonic.net/avc/oss/bdplayer/AWBPM14A.html
(1) MS/WMA
This product is protected by certain intellectual property rights of
Microsoft Corporation and third parties. Use or distribution of such
technology outside of this product is prohibited without a license
from Microsoft or an authorized Microsoft subsidiary and third
parties.
(2) MS/PlayReady/Final Product Labeling
This product contains technology subject to certain intellectual
property rights of Microsoft. Use or distribution of this technology
outside of this product is prohibited without the appropriate
license(s) from Microsoft.
(3) MS/PlayReady/End User Notices
Content owners use Microsoft PlayReadyTM content access
technology to protect their intellectual property, including
copyrighted content. This device uses PlayReady technology to
access PlayReady-protected content and/or WMDRM-protected
content. If the device fails to properly enforce restrictions on
content usage, content owners may require Microsoft to revoke the
device’s ability to consume PlayReady-protected content.
Revocation should not affect unprotected content or content
protected by other content access technologies. Content owners
may require you to upgrade PlayReady to access their content. If
you decline an upgrade, you will not be able to access content that
requires the upgrade.
(4) FLAC, WPA Supplicant
The software licenses are displayed when “License” in the Setup
menu is selected. (&gt; 29)
Copyright 2004-2010 Verance Corporation. CinaviaTM is a Verance
Corporation trademark. Protected by U.S. Patent 7,369,677 and
worldwide patents issued and pending under license from Verance
Corporation. All rights reserved.
36
SQT0080
DMP-BDT460_360_SQT0080_eng.book
37 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Limited Warranty
(ONLY FOR U.S.A. AND PUERTO RICO)
Panasonic Products Limited Warranty
Limited Warranty Coverage (For USA and Puerto Rico Only)
If your product does not work properly because of a defect in materials or
workmanship, Panasonic Corporation of North America (referred to as “the
warrantor”) will, for the length of the period indicated on the chart below, which
starts with the date of original purchase (“warranty period”), at its option either
(a) repair your product with new or refurbished parts, (b) replace it with a new or
a refurbished equivalent value product, or (c) refund your purchase price. The
decision to repair, replace or refund will be made by the warrantor.
Product or Part Name
Parts
Blu-ray Disc Player
1 Year
Labor
90 Days
All included Accessories
(Except Non-Rechargeable Batteries)
90 Days
Not Applicable
Only Non-Rechargeable Batteries
10 Days
Not Applicable
During the “Labor” warranty period there will be no charge for labor. During the
“Parts” warranty period, there will be no charge for parts. This Limited Warranty
excludes both parts and labor for non-rechargeable batteries, antennas, and
cosmetic parts (cabinet). This warranty only applies to products purchased and
serviced in the United States or Puerto Rico. This warranty is extended only to
the original purchaser of a new product which was not sold “as is”.
Mail-In Service--Online Repair Request
Online Repair Request
To submit a new repair request and for quick repair status visit our Web Site at
www.panasonic.com/repair.
When shipping the unit, carefully pack, include all supplied accessories listed in
the Owner’s Manual, and send it prepaid, adequately insured and packed well in
a carton box. When shipping Lithium Ion batteries please visit our Web Site at
www.panasonic.com/BatteryHandling as Panasonic is committed to providing
the most up to date information. Include a letter detailing the complaint, a return
address and provide a daytime phone number where you can be reached. A
valid registered receipt is required under the Limited Warranty.
IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD, THE
PURCHASER WILL BE REQUIRED TO FURNISH A SALES RECEIPT/
PROOF OF PURCHASE INDICATING DATE OF PURCHASE, AMOUNT PAID
AND PLACE OF PURCHASE. CUSTOMER WILL BE CHARGED FOR THE
REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF OF
PURCHASE.
Limited Warranty Limits And Exclusions
This warranty ONLY COVERS failures due to defects in materials or
workmanship, and DOES NOT COVER normal wear and tear or cosmetic
damage. The warranty ALSO DOES NOT COVER damages which occurred in
shipment, or failures which are caused by products not supplied by the
warrantor, or failures which result from accidents, misuse, abuse, neglect,
mishandling, misapplication, alteration, faulty installation, set-up adjustments,
misadjustment of consumer controls, improper maintenance, power line surge,
lightning damage, modification, introduction of sand, humidity or liquids,
commercial use such as hotel, office, restaurant, or other business or rental use
of the product, or service by anyone other than a Factory Service Center or
other Authorized Servicer, or damage that is attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER
“LIMITED WARRANTY COVERAGE”.
THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS
PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY.
(As examples, this excludes damages for lost time, travel to and from the
servicer, loss of or damage to media or images, data or other memory or
recorded content. The items listed are not exclusive, but for illustration only.)
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY
OF MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED
WARRANTY.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty lasts, so
the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state. If a problem with this product develops during or
after the warranty period, you may contact your dealer or Service Center. If the
problem is not handled to your satisfaction, then write to the warrantor’s
Consumer Affairs Department at the addresses listed for the warrantor.
PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED
WARRANTY, ARE YOUR RESPONSIBILITY.
Customer Services Directory (United States and Puerto Rico)
Obtain Product Information and Operating Assistance; locate your
nearest Dealer or Service Center; purchase
Parts and Accessories; or make Customer Service and
Literature requests by visiting our Web Site at:
http://www.panasonic.com/support
or, contact us via the web at:
http://www.panasonic.com/contactinfo
For hearing or speech impaired TTY users, TTY: 1-877-833-8855
Accessory Purchases (United States and Puerto Rico)
Purchase Parts, Accessories and Owner’s Manual online for all Panasonic
Products by visiting our Web Site at:
http://www.pstc.panasonic.com
Or, send your request by E-mail to:
[email protected]
You may also contact us directly at:
1-800-237-9080 (Fax Only)
(Monday-Friday 9am-9pm EST)
Panasonic National Parts Center
20421 84th Avenue South, Kent, WA 98032
(We accept Visa, MasterCard, Discover Card, American Express)
For hearing or speech impaired TTY users, TTY: 1-866-605-1277
As of November 2013
The model number and serial number of this product can be
found on either the back or the bottom of the unit.
Please note them in the space provided below and keep for
future reference.
MODEL NUMBER
Reference
SERIAL NUMBER
User memo:
DATE OF PURCHASE
DEALER NAME
DEALER ADDRESS
TELEPHONE NUMBER
SQT0080
37
DMP-BDT460_360_SQT0080_eng.book
38 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Limited Warranty (Only for CANADA)
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3
PANASONIC PRODUCT - LIMITED WARRANTY
EXCHANGE PROGRAM
Panasonic Canada Inc. warrants this product to be free from defects in material and workmanship under normal use
and for a period as stated below from the date of original purchase agrees to, at its option either (a) repair your product
with new or refurbished parts, (b) replace it with a new or a refurbished equivalent value product, or (c) refund your
purchase price. The decision to repair, replace or refund will be made by Panasonic Canada Inc.
Panasonic BD / DVD Player
Panasonic Streaming Player
One (1) year
One (1) year
This warranty is given only to the original purchaser, or the person for whom it was purchased as a gift, of a Panasonic
brand product mentioned above sold by an authorized Panasonic dealer in Canada and purchased and used in
Canada, which product was not sold “as is”, and which product was delivered to you in new condition in the original
packaging.
IN ORDER TO BE ELIGIBLE TO RECEIVE WARRANTY SERVICE HEREUNDER, A PURCHASE RECEIPT OR
OTHER PROOF OF DATE OF ORIGINAL PURCHASE, SHOWING AMOUNT PAID AND PLACE OF PURCHASE IS
REQUIRED.
LIMITATIONS AND EXCLUSIONS
This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT COVER normal
wear and tear or cosmetic damage. The warranty ALSO DOES NOT COVER damages which occurred in shipment, or
failures which are caused by products not supplied by Panasonic Canada Inc., or failures which result from accidents,
misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, set-up adjustments, misadjustment
of consumer controls, improper maintenance, power line surge, lightning damage, modification, introduction of sand,
humidity or liquids, commercial use such as hotel, office, restaurant, or other business or rental use of the product, or
service by anyone other than an Authorized Servicer, or damage that is attributable to acts of God.
Dry cell batteries are also excluded from coverage under this warranty.
THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR ANY SPECIAL, INDIRECT OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY
BREACH OF ANY EXPRESS OR IMPLIED WARRANTY. (As examples, this warranty excludes damages for lost time,
travel to and from the Authorized Servicer, loss of or damage to media or images, data or other memory or recorded
content. This list of items is not exhaustive, but for illustration only.)
In certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages,
or the exclusion of implied warranties, so the above limitations and exclusions may not be applicable. This warranty
gives you specific legal rights and you may have other rights which vary depending on your province or territory.
CONTACT INFORMATION
For product operation and information assistance, please visit our Support page:
www.panasonic.ca/english/support
For defective product exchange within the warranty period, please contact the original dealer.
38
SQT0080
DMP-BDT460_360_SQT0080_eng.book
39 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Referencia r&aacute;pida en espa&ntilde;ol
(Spanish Quick Reference)
Preparaci&oacute;n
Encienda el televisor y seleccione la entrada de
v&iacute;deo adecuada en el televisor.
Conexiones b&aacute;sicas
Conexi&oacute;n a un televisor
compatible con HDMI
[BDT361]
[BDT460] [BDT360]
Cable HDMI
Reproducci&oacute;n b&aacute;sica
1
Pulse [&Iacute;] para encender la unidad.
Despu&eacute;s de conectar su nuevo reprodutor y
pulsar el bot&oacute;n de encendido, aparecer&aacute; la
pantalla de la configuraci&oacute;n b&aacute;sica.
HDMI IN
2
Inserte el medio.
Inicia la reproducci&oacute;n
Pulse [1PLAY].
Conexi&oacute;n a un televisor
compatible con HDMI y a un
amplificador/receptor
compatible con HDMI
Cable HDMI
HDMI IN
[BDT361]
[BDT460] [BDT360]
Parada
Pulse [∫STOP].
La posici&oacute;n de detenci&oacute;n se memoriza.
Funci&oacute;n de reanudaci&oacute;n de la reproducci&oacute;n
Pulse [1PLAY] para reiniciar la reproducci&oacute;n
desde esta posici&oacute;n.
≥ La posici&oacute;n se borra si se abre la bandeja.
≥ En los discos BD-Video incluidos los BD-J, la funci&oacute;n
de reanudaci&oacute;n de la reproducci&oacute;n no funciona.
(ARC)
Pausa
Pulse [;PAUSE].
≥ Pulse [;PAUSE] otra vez o [1PLAY] para reiniciar la
reproducci&oacute;n.
HDMI IN
HDMI OUT
(ARC)
Amplificador/Receptor
Conecte el cable de
alimentaci&oacute;n de CA por
&uacute;ltimo
A una toma de corriente dom&eacute;stica
B&uacute;squeda/C&aacute;mara lenta
B&uacute;squeda
Durante la reproducci&oacute;n, pulse [SEARCH6]
o [SEARCH5].
C&aacute;mara lenta
Durante la pausa, pulse [SEARCH5].
La velocidad aumenta hasta 5 pasos.
≥ M&uacute;sica y MP3, etc.: La velocidad est&aacute; fija en un paso.
≥ Pulse [1PLAY] para recuperar la velocidad de
reproducci&oacute;n normal.
Cable de alimentaci&oacute;n de CA (incluido)
≥ Con&eacute;ctelo cuando haya realizado el resto de conexiones.
Ahorro de energ&iacute;a
Durante la reproducci&oacute;n o la pausa, pulse
[:] o [9].
Salta hasta el t&iacute;tulo, cap&iacute;tulo o pista que desee
reproducir.
Esta unidad consume una peque&ntilde;a cantidad de energ&iacute;a
aunque est&eacute; ajustada en el modo de espera (Accionamiento
r&aacute;pido : Desactivado, aprox. 0,5 W). Para ahorrar energ&iacute;a
cuando no vaya a utilizar la unidad durante mucho tiempo,
desench&uacute;fela de la toma de corriente.
SQT0080
39
Reference
Salto
DMP-BDT460_360_SQT0080_eng.book
42 ページ ２０１３年１２月１９日　木曜日　午後３時０分
Index
A Audio
Changing audio . . . . . .17
Language . . . . . . . .26, 35
B BD-Live . . . . . . . . . . . . . .18
C Closed Caption . . . . .23, 26
D DLNA . . . . . . . . . . . . . . . .20
DMC . . . . . . . . . . . . . . . . . 21
F File format. . . . . . . . . . . .34
Firmware update . . . . . . . 13
H HDMI CEC . . . . . . . . . . . .22
L LAN . . . . . . . . . . . . . . . . .11
Language
Audio . . . . . . . . . . . . . 26
Menu. . . . . . . . . . . . . . 26
On-screen. . . . . . . . . . 26
Soundtrack . . . . . . . . . 22
Subtitle . . . . . . . . . 22, 26
M Media Renderer . . . . . . 21
Miracast . . . . . . . . . . . . . 20
Multi User Mode . . . . . . . 16
N Network
Connection . . . . . . . . . 11
Setting . . . . . . . . . 12, 26
Network Service . . . . . . .19
P Pop-up menu . . . . . . . . . . 17
Q Quick Start . . . . . . . . . . 28
R Repeat play . . . . . . . . . . 22
Restore Default
Settings . . . . . . . . . . . . . . 29
Resume play function . . . 17
S Subtitle . . . . . . . . . . . . . 22
U USB device . . . . . . . . . . . 7
W Wireless LAN . . . . . . . . 11
24p . . . . . . . . . . . . . . . 23, 24
USA Only: Disposal may be regulated in your community due to environmental considerations. For
disposal or recycling information, please visit Panasonic website:
http://www.panasonic.com/environmental/
or call 1-888-769-0149.
&reg;
As an ENERGY STAR Partner, Panasonic
has determined that this product meets the
&reg;
ENERGY STAR guidelines for energy
efficiency.
For Canada only: The word “Participant” is
used in place of the word “Partner”.
Panasonic Corporation of North
America
Two Riverfront Plaza, Newark, NJ
07102-5490
http://www.panasonic.com
C Panasonic Corporation 2013
Printed in China
Panasonic Canada Inc.
5770 Ambler Drive,
Mississauga, Ontario,
L4W 2T3
www.panasonic.com
pr
SQT0080
F1213SK0
">
سلام! من یک ربات چت هوش مصنوعی هستم که به طور خاص برای کمک به شما در مورد Panasonic DMP-BDT360 Blu-ray Player Owner's Manual آموزش دیده‌ام. من سند را به طور کامل بررسی کرده‌ام و می‌توانم به شما کمک کنم اطلاعات دقیقی را که نیاز دارید پیدا کنید یا محتوا را به زبان ساده و واضح توضیح دهم. چه به دنبال راهنمایی در مورد ویژگی‌های خاص، مراحل عیب‌یابی یا استفاده عمومی باشید، می‌توانید سوالات خود را بپرسید. هرچه جزئیات بیشتری در مورد نگرانی‌ها یا نیازهای خود ارائه دهید، من می‌توانم دقیق‌تر و موثرتر به شما کمک کنم!