Two Year Limited Warranty
Your Inspired by Drive branded product is warrantied to be
free of defects in materials and workmanship for two years of
the original consumer purchaser.
This device was built to exacting standards and carefully
inspected prior to shipment. This Two Year Limited Warranty
is an expression of our confidence in the materials and
workmanship of our products and our assurance to the
consumer of years of dependable service.
This warranty does not cover device failure due to owner
misuse or negligence, or normal wear and tear. The warranty
does not extend to non-­durable components, such as rubber
accessories, casters, and grips, which are subject to normal
wear and need periodic replacement.
Tusky Tilt & Recline
Positioning Chair
If you have a question about your Inspired by Drive device or
this warranty, please contact an authorized Inspired by Drive
dealer.
Item # APT 3000
2017 Medical Depot, Inc. All rights reserved.
Drive DeVilbiss Healthcare
99 Seaview Boulevard
Port Washington N.Y. 11050 USA
Made in China
EU Authorized Representative
Drive Medical LTD
Ainley’s Industrial Estate
Elland, West Yorkshire,
United Kingdom HX5 9JP
www.inspiredbydrive.com
REV1.09.13.17
assembly:
6. Insert footrest assembly (D) into bracket (F) under the seat of the chair
and tighten knob (Y).
1. Remove all positioning components from box.
7. Insert abductor (G) into round receptacle bracket (Z) and tighten
knob (E).
2. Remove bolts (A) and insert back mounting bracket (AG) in the
following order:
G
- Seat pan (AH)
- Back mounting bracket (AG)
F
Reinsert bolts.
3. Lift up back to desired angle and seat depth and tighten bolts (A).
D
4. Insert arm rest assembly into mounting brackets (C).
Z
E
AG
8. Insert vertical pole of headrest (H) into bracket (I) on back of chair and
turn knob (J) to tighten. Tighten allen screws (K) on triangular bracket
(L) and on the back of the headrest cushion (M)
C
AH
Y
M
A
L
5. Insert laterals in bracket (B) and tighten knob (V)
K
B
I
V
J
H
adjustments:
ARM RESTS
TILT POSITION
Depth – Loosen bolts (AF) and adjust.
Height – Loosen knob (S) and adjust armrest assembly.
Open knob (N) and slide the securing bracket (O) away. Press tilt actuator
(P) and push down on chair while holding on to both handles (Q) to desired
tilt angle. Return securing bracket (O) and tighten knob (N).
O
S
N
T
AF
SEAT WIDTH
There are two sets of hip guides included with this product. The set you
use will determine the seat width. They can be switched by removing bolt
(T) and replacing with the other set. Each set comes with its own bolts.
Q
P
BACK HEIGHT
Back height can be adjusted by
loosening knobs (U) and raising or
lowering back.
SEAT TO BACK ANGLE AND SEAT DEPTH
Loosen bolts (A) and position back at desired depth. Place seat to back
angle at desired setting.
V
A
U
LATERALS
Laterals can be adjusted in
height and width. Loosen knob
(V) and adjust height and width.
HEADRESTS
ABDUCTOR
Height
Abductor can be removed and adjusted by loosen the knob (Z). Slide the
abductor in or out for proper depth and tighten the knob.
Loosen knob (J) and raise or lower vertical assembly pole.
Depth
Loosen 3 Allen screws (K) on triangular rotating bracket and push/pull
headrest to desired position. For additional depth adjustability, mount the
vertical assembly pole with the curve either facing inward or outward.
Angle
Loosen 3 Allen screws (M) on circular bracket on headrest and tilt
headrest to desired angle. Additional angle adjustability can be achieved
by loosening the 3 Allen screws (K) on the triangular rotating bracket and
adjust accordingly.
M
Z
LAP BELT
Length – Use buckle &/or change the position of the hook and loop straps
under the seat.
K
HARNESS
The top and side hook and
loop straps on the back of
the chair adjust the length of
the straps.
J
FOOTRESTS
ACCESSORIES BASE
Height - Loosen bolts (W & X) and raise or lower bracket.
APT-A0014 — High base
Angle – Loosen bolt (X).
APT-A0015 — Low base
Mount chair onto either base. Lock chair onto base by sliding bracket
(AC) over cross bar (AD).
X
X
W
AC
W
AD
">
