Techlogix TL-6X1-HDV User manual

User Manual

TL-6X1-HDV

Compact Scaler Switcher 6x1

All Rights Reserved

Version: TL-6X1-HDV_160711

TL-6X1-HDV User Manual

Preface

Read this user manual carefully before using this product. Pictures shown in this manual are for reference only, different model and specifications are subject to real product.

This manual is only for operation instruction only, not for any maintenance usage.

Trademarks

Mentioned product model and logo are trademarks. Any other trademarks mentioned in this manual are acknowledged as the properties of the trademark owner. No part of this publication may be copied or reproduced without the prior written consent.

FCC Statement

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. It has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation.

Operation of this equipment in a residential area is likely to cause interference, in which case the user at their own expense will be required to take whatever measures may be necessary to correct the interference.

Any changes or modifications not expressly approved by the manufacture would void the user’s authority to operate the equipment. www.tlnetworx.com


SAFETY PRECAUTIONS

To insure the best from the product, please read all instructions carefully before using the device. Save this manual for further reference. l

Unpack the equipment carefully and save the original box and packing material for possible future shipment l

Follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. l

Do not dismantle the housing or modify the module. It may result in electrical shock or burn. l

Using supplies or parts not meeting the products’ specifications may cause damage, deterioration or malfunction. l

Refer all servicing to qualified service personnel. l

To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water. l

Do not put any heavy items on the extension cable in case of extrusion. l

Do not remove the housing of the device as opening or removing housing may expose you to dangerous voltage or other hazards. l

Install the device in a place with fine ventilation to avoid damage caused by overheat. l

Keep the module away from liquids. l

Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on to the housing, unplug the module immediately. l

Do not twist or pull by force ends of the optical cable. It can cause malfunction. l

Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning. l

Unplug the power cord when left unused for a long period of time. l

Information on disposal for scrapped devices: do not burn or mix with general household waste, please treat them as normal electrical wastes. www.tlnetworx.com


Contents

1.

Introduction ................................................................................................................. 1

1.1

Introduction to TL-6X1-HDV .............................................................................. 1

1.2

Features .............................................................................................................. 1

1.3

Package List ........................................................................................................ 2

2.

Panel Description ......................................................................................................... 3

2.1

Front Panel ......................................................................................................... 3

2.2

Rear Panel ........................................................................................................... 4

3.

System Connection ...................................................................................................... 5

3.1

Usage Precautions .............................................................................................. 5

3.2

System Diagram .................................................................................................. 5

3.3

Connection Procedures ...................................................................................... 5

3.4

Application .......................................................................................................... 6

4.

System Operations ....................................................................................................... 7

4.1

Front Panel Button Control ................................................................................. 7

4.2

RS232 Control .................................................................................................... 8

4.2.1

Control Software Operation ..................................................................... 8

4.2.2

Basic Settings ........................................................................................... 8

4.2.3

RS232 Communication Commands .......................................................... 9

4.3

IR control .......................................................................................................... 14

4.4

Firmware Updating ........................................................................................... 14

5.

Specification .............................................................................................................. 15

6.

Panel Drawing ............................................................................................................ 19

7.

Troubleshooting & Maintenance ................................................................................ 20

8.

After-sales Service ..................................................................................................... 21 www.tlnetworx.com


1.

Introduction

1.1

Introduction to the TL-6X1-HDV

The TL-6X1-HDV is a compact 6x1 switcher unit with 6 video inputs (4 HDMI, 2 VGA), 2 auxiliary audio inputs (switched following VGA), 1 HDMI output and 3 audio outputs (1 dual-mono analog audio, 1 3.5mm stereo audio, 1 optical audio).

The TL-6X1-HDV switches VGA or HDMI/DVI input signal to HDMI output. The unit up-scales VGA to HDMI output and supports resolution adjustment (6 types in total).

HDMI bypasses the scalers and provides comprehensive resolution capabilotes up to

4K& 1080p 3D. The unit also supports RS232&IR control and EDID management.

1.2

Features

l

Control -- via Front panel buttons, RS232 commands and IR Remote l

Switch -- select 6 input sources to 1 HDMI output l

Scale – scale VGA to HDMI output, Output resolutions selectable to assure preferred output, and supports various output resolutions, such as 1920x1200，1920x1080，

1360x768，1280x800，1024x768，1280x720 l

Supports HDMI 1.4, 4Kx2K&1080P 3D, compliance with HDCP1.4. l

Transmits 4Kx2K signal up to 15m. l

Supports EDID management l

Two input switching modes: auto-switching or manual-switching l

Intuitive indicator for power connect states & source selection & output resolution selection l

Supports audio & video output management via OUTPUT BLACK button. l

Supports online software upgrading l

Compact design for easy installation l

Supports power-off memory l

Supports hot plug

1 www.tlnetworx.com


1.3

Package List

l

1 x TL-6X1-HDV l

2 x Mounting ears (separate from TL-6X1-HDV) l

4 x Screws l

4 x Plastic cushions l

1 x Power adapter (DC 5V 3A) l

2 x 3-pin Pluggable terminal blocks (pitch:3.81mm) l

1 x IR Receiver l

1 x IR Remote (Cell battery is not included) l

1 x User manual

Notes：

Confirm all the accessories are included, if not, please contact your authorized dealer.

2 www.tlnetworx.com


2.

Panel Description

2.1

Front Panel

AUTO/3s FW UPDATE/7s

HDMI 1 HDMI 2 HDMI 3 HDMI 4 VGA 1 VGA 2 AUTO 1024x768 1280x720 1280x800 1360x768 1920x1080 1920x1200 SOURCE RESOLUTION OUTPUT BLACK

No. Name

① Power LED

Description

Indicator for power status l

Off when no power. l Green when the system is powered on. l

Red when the system is in standby.

② Inputs LED Green when the corresponding source is connected..

③ Auto-switching LED Green when in auto-switching mode.

④

Output resolution selection LED

⑤ SOURCE/AUTO

⑥

RESOLUTION/FW

UPDATE

⑦ OUTPUT BLACK

Green when the corresponding output is selected (Input is

VGA). l

Audio source selection button: switches in series HDMI1,

HDMI2, HDMI3, HDMI4, VGA1, VGA2. Press ◀ to select the previous one, Press ▶ to select the next one. l

Switching mode selection button ◀: press and hold for 3 seconds or more to enter auto-switching mode, press and hold for 3 seconds or more again to enter

manual-switching mode. l Output resolution manual sselection button for VGA input: selects in series 1920×1200, 1920×1080, 1360×768,

1280×800, 1024×768, 1280×720.default resolution:1920×1080. l Firmware updating button: press and hold for 7 seconds or more to enter software updating procedure. All LEDs blink when the system is loading firmware

Press to switch on/off audio&Video output. All LEDs turn off except power LED when the output is switched off.

Note: Pictures shown in this manual are for reference only, different model and specifications are subject to real product.

3 www.tlnetworx.com


2.2

Rear Panel

HDMI 1 HDMI 2 HDMI 3 HDMI 4

INPUTS

VGA 1 AUDIO 1 VGA 2

L

OUTPUTS

R

CONTROL

Tx Rx

POWER

AUDIO 2 HDMI AUDIO AUDIO OPTICAL FIRMWARE RS 232 IR IN DC 5V

No. Name

① INPUTS

② OUTPUTS

③ Control

Description

l HDMI: 4 HDMI/DVI video source input ports (embedded HDMI audio format：PCM). l VGA: 2 VGA video source input ports. l

AUDIO: 2 3.5mm stereo audio source input ports, switched following the corresponding VGA. l

HDMI: HDMI video output port. l 3P AUDIO: Stereo analog audio output port. l 3.5mm AUDIO: Stereo analog audio output port. l OPTICAL: Optical audio output port. l

FIRMWARE: Type-A USB port for updating firmware. l

RS232: Serial port, 3-pin pluggable terminal block, connect with control terminal (e.g. a PC) to control TL-6X1-HDV. l IR IN: connect to an IR Receiver, to receive IR signal sent by corresponding IR remote.

④ DC 5V Connect to a DC 5V 3A power adapter.

Note: Pictures shown in this manual are for reference only, different model and specifications are subject to real product.

4 www.tlnetworx.com


3.

System Connection

3.1

Usage Precautions

1) System should be installed in a clean environment that has proper temperature and humidity.

2) All of the power switches, plugs, sockets and power cords should be insulated and safe.

3) All devices should be connected before powering on.

3.2

System Diagram

IR Remote

PC

DV Camera

DVD

HDTV

Speaker1

Speaker2

HDMI/DVI Signal ：

VGA Signal

：

AUDIO Signal ：

IR Signal ：

RS232 Signal

：

Figure 3- 1 Connection Diagram

3.3

Connection Procedures

Step1. Connect HDMI/DVI sources (e.g. DVD) to HDMI input ports of TL-6X1-HDV with HDMI cables.

Step2. Connect VGA sources (e.g. DV Camera) to VGA input ports of TL-6X1-HDV with

VGA cables.

Step3. Connect sources to the AUDIO input ports of TL-6X1-HDV with audio cables.

Step4. Connect a HDMI display (e.g. HDTV) to HDMI output port of TL-6X1-HDV.

Step5. Connect audio amplifiers to audio outputs of TL-6X1-HDV.

Step6. Connect a control device (e.g. PC) to the RS232 port of TL-6X1-HDV

Step7. Connect an IR Receiver（working voltage:5V）to the IR IN port of TL-6X1-HDV.

Step8. Plug DC 5V 3A power adapter to TL-6X1-HDV.

5 www.tlnetworx.com


3.4

Application

TL-6X1-HDV has a many applications such as conference rooms, training rooms, command & control centers and corporate board rooms.

6 www.tlnetworx.com


4.

System Operations

4.1

Front Panel Button Control

Front panel buttons can be used for source selection, output resolution adjusting, front panel button management, software updating and output screen muting. (Please refer to chapter 2.1).

Here is the detailed information for source selections:

There are 6 sources for choose in total, including HDMI1, HDMI2, HDMI3, HDMI4,

VGA1, VGA2. Video signals support auto-switching and manual-switching (factory default). Press and hold SOURCE/AUTO for 3 seconds or more to enter auto-switching/ manual-switching mode.

Manual-switching:

Press ◀ to select the previous source, Press ▶ to select the next source.

Auto-switching:

In this mode, selecting an input source via front panel button (◀ ▶) is not possible, but

RS232 command and IR remote are able to switch inputs. The auto LED will be lit

(green).

The auto-switching mode abides by the following principles: l

New input principle

Once detecting a new input signal, TL-6X1-HDV will switch to this new signal automatically. l

Rebooting device principle

TL-6X1-HDV features power cycle memory. If the last switching mode is auto-switching, once rebooted, TL-6X1-HDV will automatically enter auto-switching mode, then detect all inputs and store their connection status for reboot. If the last displayed signal is still available, TL-6X1-HDV will output that signal. If not, the unit will detect all the input signals with priority from HDMI1 to VGA2. The first signal detected will be selected. l

Signal removing principle

If the current display signal is removed, TL-6X1-HDV will detect all input signals with priority from HDMI1 to VGA2. The first signal detected will be selected.

7 www.tlnetworx.com


Operation Examples: l

Connect HDMI2, HDMI4, and VGA2 ports to source devices, select HDMI4. l

Press and hold the SOURCE/AUTO button for 3 seconds or more to enter auto-switching mode. l

Connect a source device to HDMI3, it will be selected automatically. l

Remove the signal from HDMI3, TL-6X1-HDV will search from HDMI1 to VGA2. It will detect that HDMI2 is available, HDMI2 will be selected automatically. l

Remove power from the TL-6X1-HDV, then reboot. As the unit is in auto-switching mode, HDMI2 will be selected.

4.2

RS232 Control

Here we take the software CommWatch.exe as example.

4.2.1

Control Software Operation

l

Installation Copy the control software file to the computer connected with

TL-6X1-HDV. l

Uninstallation Delete all the control software files in the corresponding file path.

4.2.2

Basic Settings

First, connect TL-6X1-HDV with an input device and an output device. Then, connect it to a computer which has the RS232 control software installed. Double-click the software icon to run this software. The icon is showed below:

The interface of the control software is showed below:

8 www.tlnetworx.com


Parameter Configuration area

Monitoring area, indicates whether the command sent works.

Command Sending area

Please set the parameters of COM number, baud rate, data bit, stop bit and the parity bit correctly, only then will you be able to send commands in the Command Sending Area.

4.2.3

RS232 Communication Commands

Baud rate: 9600 Data bit: 8 Stop bit: 1 Parity bit: none

Command

Function

Feedback Example

50701%

Switch Commands

Switch to HDMI 1 Input Switch to HDMI 1

50702%

50703%

50704%

50705%

Switch to HDMI 2 Input



Switch to VGA 1 input

Switch to HDMI 2

Switch to HDMI 3

Switch to HDMI 4

Switch to VGA 1

9 www.tlnetworx.com

50706%

50785%

50786%

50619%

50620%

50626%

50627%

50628%

50629%

50604%

50605%

502xx%

503xx%

504xx%

505xx%

50607%

50608%

50614%


Switch to VGA 2 input

Enable auto-switching

Switch to VGA 2

Auto Switching

Disable auto-switching Manual Switching

Resolution Select Commands for VGA Input

Change the resolution to 1360X 768 Resolution: 1360x768

Change the resolution to1920X1200

WUXGA

Resolution: 1920x1200

Change the resolution to 1024X768 XGA Resolution: 1024x768

Change the resolution to 1280X720 720P Resolution: 1280x720

Change the resolution to 1280X800

WXGA

Change the resolution to 1920X1080

1080P



Setup Commands

Lock the front panel buttons

Unlock the front panel buttons

Set the brightness to xx (xx ranges from 0 to 99) for VGA input

Set the contrast to xx (xx ranges from 0 to

99) for VGA input

Set the saturation to xx (xx ranges from 0 to 99) for VGA input

Set the sharpness to xx (xx ranges from 0 to 99) for VGA input

Front Panel lock

Front Panel Unlock

Brightness: xx

Contrast: xx

Saturation: xx

Sharpness: xx

Adjust the color temperature for VGA input

Set the aspect ratio for VGA input

Set the picture mode for VGA input

Color Temperature: xx

(xx= Cool/ Medium/

Warm/ User.)

Aspect Ratio: xx

(xx= 16:9/ 4:3/ auto/)

Picture Mode: xx (xx= dynamic/ standard/ mild/ user)

10 www.tlnetworx.com

50648%

50649%

50606%

50699%

50697%

50797%

50698%

50617%

50707%

50769%

50772%

50773%

50774%

50775%

50776%

50777%

50615%

50708%


Set the audio mode for VGA input

Enable HDMI embedded audio output

Disable HDMI embedded audio output

Sound Mode: xx

Sound Mode: xx (xx= standard/ music/ movie/ sports/ user)

Embedded Audio Output: enable

Embedded Audio Output: disable

Auto-adjust the input parameter for (VGA only)

Check the system version

Exit standby mode

Enter standby mode

Software update

Reset to factory defaults

Change the horizontal polarity to the opposite,1 means positive polarity,0 means negative polarity

Change the vertical polarity to the opposite,1 means positive polarity,0 means negative polarity

Read the EDID file( the file must be named EDID.bin) to the flash from U flash disk

Set the EDID date of all input ports: bypass mode

Set the EDID date of all input ports:

1080P&PCM 2ch

Set the EDID date of all input ports:1080P&5.1ch


1080P 3D&5.1ch


1080i&PCM 2ch


4K&PCM 2ch

11

VGA Input Auto

Version Vx.x.x

Wake up!

Go to standby!

Factory Reset

Hpolarity:0/1

Vpolarity:0/1

EDID:bypass mode

EDID:1080P&PCM 2ch

EDID:1080P&5.1ch

EDID:1080P3d&5.1ch

EDID:1080i&PCM 2ch

EDID:4K&PCM 2ch www.tlnetworx.com

50787%

50653%

50654%

50631%

50632%

50633%

50634%

50635%

50636%

50637%

50638%

50639%

50640%

50652%

50655%

50709%

50754%

50778%

50670%

50671%

50672%

50673%


Set the EDID date of all input ports: user

Switch off audio&video output

Switch on audio&videio output

EDID:user

Output black:enable

Output black:disable

Switch to VGA2

Inquire Commands

Check the input source

Check the output resolution

Check the image mode

Check the audio mode

Check the image aspect ratio

Check the brightness

Check the contrast

Check the saturation

Check sharpness

Check the color temperature

Check Digital audio output status

Input: xx

Resolution: xx

Picture Mode: xx

Sound Mode: xx

Aspect Ratio: xx

Brightness: xx

Contrast: xx

Saturation: xx

Sharpness: xx

Color Temperature: xx

Embedded Audio Output: enable/disable

Check video&audio output status

Check the present resolution and polarity

50655%

Black screen Disable/

Black screen Enable

1920x1080

Hpolarity:1

Vpolarity:0

Front Panel Lock/UnLock Check the panel locked status

Inquire EDID s EDID:xx

Adjustment Commands for VGA input

Move the image to left

Output Position Adjust X xx

Move the image to right

Move the image up

Move the image down

Output Position Adjust X xx

Output Position Adjust Y xx

Output Position Adjust Y xx



50674%

50675%

50676%

50677%

Stretch left from left side (increase image width)

Pull right from left side (decrease image width)

Stretch upwards from top side (increase image height)

Stretch downwards from top side(decrease image height)

Output Width Adjust xx

Output Width Adjust xx

Output Height Adjust xx

Output height adjust xx

50678% Enable screen output adjusting

Enter Output Position

Adjust

Exit Output Position Adjust 50679% Disable screen output adjusting

Notes:

1 Please remember to end the commands with the ending symbol “%”.

2 EDID commands are for HDMI sources only.

3 The procedure of upgrading EDID data for user:

Step1.

Copy the file(the file must be named EDID.bin) to the root directory of a USB flash disk.

Step2.

Plug the USB flash disk to the TL-6X1-HDV Firmware port on its rear panel.

Step3.

Send command 50769% to read EDID data from U flash disk, then, send command 50787% to update EDID.



4.3

IR control

The unit enables to use the IR remote to control it. Here is brief description of IR remote.

①

Standby button

Enter/exit standby mode.

②

Input channel selection buttons

Select video source by pressing the corresponding button (audio switched following the corresponding VGA).

③

Auto button

Enter/ exit auto-switching mode.

④

Resolution selection buttons

Select resolution by pressing the corresponding button.

⑤

Output black button

Press to switch on/off Audio& Video output

4.4

Firmware Updating

TL-6X1-HDV supports firmware updating via USB flash disk. The procedures as follows:

Step1.

Copy the file “MERGE.bin” to the root directory of a USB flash disk. (Make sure the file is copied to the root directory for normal use. The “MERGE.bin” file is provided/ authorized.

Step2.

Plug the USB flash disk to TL-6X1-HDV FIRMWARE port on its rear panel.

Step3.

Press the button “RESOLUTION/FW UPDATE” for 7 seconds or more to update the firmware automatically. Or send command 50698% to update software.


5.

Specification


I/O Connections

HDM Inputs

VGA Inputs

Audio Inputs

HDMI Output

Audio Outputs

IR Input

RS232 Control

Button Control(Front Panel)

Firmware Update

DC 5V Power

Four(4) Type A receptacle

Two(2) HD-15 female receptacle

Two(2) 3.5mm TRS jack

One(1) Type A receptacle

One(1) 3-pin captive screw connector, One(1)

3.5mm TRS jack, One(1) optical jack

One(1) 3.5mm TRS jack

One(1) 3-pin captive screw connector

Four(4) buttons in total

One(1) Type A receptacle

One(1) Power connector with locking screw

(5.5mm outside diameter, 2.1mm inside diameter)

Supported Video, Audio and Control

Maximum Video Compatibility

Deep color 48/36/30/24 Bit at 1080P,3D and

4Kx2K(UHD)

1920x1200@60Hz, 1920x1080@60Hz,

VGA Scaling Resolution 1360x768@60Hz, 1280x800@60Hz,

1280x720@60Hz, 1024x768@60Hz.

Pass through from display, 1080P&PCM 2ch,

HDMI EDID

VGA EDID

Embedded Audio Input/output

1080P&5.1ch, 1080P3d&5.1ch, 1080i&PCM 2ch,

4K&PCM 2ch

1360x768

Up to PCM 6chanel

Digital(Optical) Audio Frequency

Response

Embedded Audio

Analog Audio

PCM:6 channel(5.1) at 16,20 or 24 bit

Up to 8 channel, Dolby Digital TrueHD, and

DTS-HD master audio

Frequency 20Hz~20K Hz



Response

Analog Audio Input Impedance > 10KΩ

Analog Audio Output Impedance

50Ω

Maximum Passive HDMI Distance 15m(49ft)

IR Carrier Frequency Range 33-55KHz at 5V

Chassis and Environmental

Enclosure Painted aluminum

350mm x 28mm x 110mm (13.78in x 1.10in x

Dimensions (W x H x D)

Shipping Weight

Operating Temperature

4.33in)

1.75Kg(3.86bls)

0° ~ +40° C(+32° ~ +104° F)

(Environment)

Operating Temperature (Chassis) 45° C(113° F)

Operating

(Environment)

Humidity

10% ~ 90% Non-condensing

Storage

(Environment)

Temperature

-15° ~ +70° C(+5° ~ +158° F)

Storage Humidity (Environment) 10% ~ 90% Non-condensing

Power, ESD, Regulatory

Maximum Power Consumption

Power Supply

3.8W

DC 5V at 3A

ESD Protection

Regulatory

Other

Standard Warranty

Indicator

15KV

CE, FCC

Included Items

3 Year

1 Power, 2 Source select, 6 resolution select

Installation guide, Power adapter, Mounting ears(2 ea), Mounting screws(8 ea), RS232 cable, Rubber feet(4 ea), IR receiver, IR remote, 3-pin captive screw connectors (2 ea)



Note: TL-6X1-HDV supports 4k&1080p 3D HDMI signal, please use quality HDMI cables compliant with HDMI1.4 for reliable transmission when connecting.



Supported Input Resolutions

Format

HDMI/DVI

Resolution

800x600@60Hz, 800x600@72Hz, 800x600@75Hz, 1024x768@42Hz,

1024x768@60Hz, 1024x768@70Hz, 1024x768@75Hz,

1024x768@85Hz, 1152x864@75Hz, 1280x768@60Hz,

1280x768@75Hz, 1280x768@85Hz, 1280x960@60Hz,

1280x960@85Hz, 1280x1024@60Hz, 1280x1024@75Hz,

1280x1024@85Hz, 1365x1024@60Hz, 1365x1024@60Hz,

1600x1024@60Hz, 1600x1200@60Hz, 1600x1200@65Hz,

1600x1200@70Hz, 1600x1200@75Hz, 1600x1200@85Hz,

1680x1050@60Hz, 1792x1344@60Hz, 1856x1392@60Hz,

1856x1392@75Hz, 1920x1080@60Hz, 1920x1200@60Hz,

1920x1440@60Hz, 3840x2160@24Hz, 3840x2160@30Hz,

3840x2160@25Hz, 4096x2160@24Hz, 4096x2160@25Hz,

4096x2160@30Hz,

VGA

800x600@60Hz, 800x600@72Hz, 800x600@75Hz, 1024x768@60Hz,

1024x768@70Hz, 1024x768@75Hz, 1280x768@60Hz,

1280x768@75Hz, 1280x960@60Hz, 1280x1024@60Hz,

1280x1024@75Hz, 1365x1024@60Hz, 1365x1024@75Hz,

1600x1024@60Hz, 1600x1200@60Hz, 1600x1200@65Hz,

1600x1200@70Hz, 1600x1200@75Hz, 1680x1050@60Hz,

1792x1344@60Hz, 1920x1080@60Hz, 1920x1200@60Hz



6.

Panel Drawing

AUTO/3s

SOURCE

FW UPDATE/7s

RESOLUTION OUTPUT BLACK HDMI 1 HDMI 2 HDMI 3 HDMI 4 VGA 1 VGA 2 AUTO 1024x768 1280x720 1280x800 1360x768 1920x1080 1920x1200

13.5 mm

350 mm



7.

Troubleshooting & Maintenance

Problems

Power LED doesn’t work or no response to any operation

No output image on display when switching

Causes

Failed connection of power cord

Power adapter dead

Failed or loose connection

Solutions

Make sure the power cord connection is normal

Please replace the power adapter

Reset the HDMI cable at the switcher and the display

Output image with snow or ghosting

Bad quality of HDMI cable

Exceeding the transmission distance

Please replace with a high quality cable.

Use a shorter HDMI cable

Cannot control the device via front panel button

Front panel buttons are locked

Send command 50605% to unlock it

Cannot select source via SOURCE/AUTO buttons

Cannot control the device by control device (e.g. a PC) through RS232 port

In auto-switching mode

Wrong RS232 communication parameters

Broken RS232 port

Press and hold the

SOURCE/AUTO button for 3 seconds or more to enter in manual-switching mode

Type in correct RS232 communication parameters.

Send it to authorized dealer for repair.

The battery is dead.

Cannot control the device via IR remote

Cannot control the device

The IR remote is broken.

Beyond the effective range of the IR signal or not pointing at the IR receiver

The device is broken.

Install a new battery.

Send it to authorized dealer for repair.

Adjust the distance and angle and point right at the IR receiver.

Send it to authorized dealer for repairing.

If your problem persists after following the above troubleshooting steps, seek further help from authorized dealer or our technical support.



8.

After-sales Service

If there appear some problems when running the device, please check and deal with the problems referenced in this user manual.

1)

Product Limited Warranty: We warrant that our products will be free from defects in materials and workmanship for three years. Please see warranty page posted on www.tlnetworx.com for more info.

2)

What the warranty does not cover: l

Warranty expiration. l

Factory applied serial number has been altered or removed from the product. l

Damage, deterioration or malfunction caused by: l

Normal wear and tear l

Use of supplies or parts not meeting our specifications l

No certificate or invoice as the proof of warranty. l

The product model showed on the warranty card does not match with the model of the product for repairing or had been altered. l

Damage caused by force majeure. l

Non-authorized service l

Other causes which does not relate to a product defect l

Delivery, installation or labor charges for installation or setup of the product

3)

Technical Support: Email to our after-sales department or make a call, please inform us the following information about your cases. l

Product version and name. l

Detailed failure situations. l

The formation of the cases.

Remarks: For any questions or problems, please try to get help from your local distributor.


Techlogix TL-6X1-HDV User manual

User Manual

Compact Scaler Switcher 6x1

All Rights Reserved

Preface

Trademarks

FCC Statement

SAFETY PRECAUTIONS

Contents

1.

Introduction

2.

Panel Description

3.

System Connection

4.

System Operations

5.

Specification

6.

Panel Drawing

7.

Troubleshooting & Maintenance

8.

After-sales Service

Related manuals

Table of contents

Techlogix TL-6X1-HDV User manual

User Manual

Compact Scaler Switcher 6x1

All Rights Reserved

Preface

Trademarks

FCC Statement

SAFETY PRECAUTIONS

Contents

1.

Introduction

2.

Panel Description

3.

System Connection

4.

System Operations

5.

Specification

6.

Panel Drawing

7.

Troubleshooting & Maintenance

8.

After-sales Service

Related manuals

SIIG

CE-H24111-S1

Woxcon

SC61E

Sewell

Rivule 6x1

Techlogix

TL-AD-HD

HDTV Supply

HD-EDID-4K

Table of contents