MASTERFORCE 207-1522 air compressor OPERATOR'S MANUAL
PDF
Dokumentum
Hirdetés
Hirdetés
5 Gallon Air Compressor 207-1522 OPERATOR’S MANUAL CAUTION: To Reduce The Risk Of Injury, User Must Read And Understand Operator’s Manual. Save These Instructions For Future Reference. Page 2 NOTES......................................................................................................................................... Page 18 Parts List ....................................................................................................................................... Page 17 Exploded View .............................................................................................................................. Page 16 Troubleshooting ............................................................................................................................ Page 14-15 .../min Designation / Explanation Type or characteristic of current To reduce the risk of injury, read and understand operator’s manual Operation of power tool can result in foreign objects being thrown into eyes Use of this tool can generate dust which may cause respiratory injury Noise from this product can contribute to hearing loss Wear gloves to reduce risk of injury Alerts user to warning messages Read the operator’s Manual Wear safety glasses Wear respiratory Protection Wear hearing Protection Wear gloves Warning symbol This Symbol Designates That This Tool Is Listed By The Canadian Standards Association This Symbol Designates That This Tool Is Listed By The Canadian Standards Association, To United States And Canadian Standards This Symbol Dsignates That This Tool Is Listed By The Intertek Testing Services, To United States And Canadian Standards This Symbol Designates That This Tool Is Listed By Underwriters Laboratories This Symbol Designates That This Tool Is Listed By Underwriters Laboratories, To United States And Canadian Standards Double-insulated construction Revolutions, strokes, surface speed orbits, etc. Per minute Class II construction Per minute Weight Rotational speed, at no load Type of current Direct current Power Frequency (cycles per second) Current Voltage Alternating current Pounds ~ Watts lbs W Operating Instructions .................................................................................................................. Page 11-12 Hertz No-load speed Hz Assembly Instructions ................................................................................................................... Page 10 Amperes Volts n0 A V Symbol Name Important Information ................................................................................................................... Page 9 Maintenance ................................................................................................................................. Page 13 SAFETY SYMBOLS Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. Tool Compatibility Chart .............................................................................................................. Page 8 Overview / Specifications .............................................................................................................. Page 7 Safety Instructions ........................................................................................................................ Page 4-6 Safety Symbols ............................................................................................................................. Page 3 Table Of Contents........................................................................................................................ Page 2 TABLE OF CONTENTS Page 3 CAUTION: Failure to obey this safety warning MAY result in personal injury to yourself or others or property damage. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury. WARNING: Failure to obey this safety warning CAN result in death or serious injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury. DANGER: Failure to obey this warning WILL result in death or serious injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury. Page 4 SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, OR CAUTION. May be used in conjucntion with other symbols or pictographs SYMBOL MEANING WARNING: Be sure to read and understand all safety insructions in this manual, including all safety alert symbols such as “DANGER”, “WARNING” and “CAUTION”, before using this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. The purpose of safety symbols is to attract our attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The symbol warnings do not by themselves eliminate any danger. The instructions and warnings they give are no substitutes for propper accident prevention measures. SAFETY INSTRUCTIONS 1. Know your power tool. Read the operator’s manual carefully. Learn the power tools applications and limitations, as well as the specific potential hazards related to this tool. 2. Stay alert, watch what you are doing and use common sense when operating a power tool. 3. Do not use tool while tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. 4. Dress properly. Do not wear loose clothing or jewelry. Pull back long hair. Keep your hair, clothing, and gloves away from moving parts. Air vents often cover moving parts and should also be avoided. Loose clothing, jewelry or long hair can be caught in moving parts. 5. Avoid accidental starting. Be sure switch is in “OFF” position before plugging in. Do not carry tools with your finger on the switch. Carrying tools with your finger on the switch or plugging in tools that have the switch in the “ON” position invites accidents. 6. Remove adjusting keys or wrenches before turning the tool “ON”. A wrench that is left attached to a rotating part of the tool may result in personal injury. 7. Do no overreach, Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. 8. Always secure your work./ Use clamps or a vise to hold work when practical. It is safer PERSONAL SAFETY 1. Keep your work area clean and well lit. Cluttered workbenches and dark areas invite accidents 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. 3. Keep bystanders, children and visitors away while operating a power tool. Distractions can cause you to lose control. 4. Make your workshop childproof with padlocks and master switches. Lock tools away when not in use. 5. Make sure the work area has ample lighting so you can see the work and that there are no obstructions that will interfere with safe operation before using your power tool. WORK AREA SAFETY Page 5 WARNING: BE SURE to read and understand all instruction before operating this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. 1. Always use clamps or other practical ways to secure and support the work piece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. 2. Do not force the tool. Use the correct tool and blade for your application. The correct tool and blade will do the job better and safer at the rate for which it is designed. 3. Do not use the tool if switch does not turn it “ON” or “OFF”. Any tool that cannot be controlled with the switch is dangerous and must be repaired. 4. Disconnect the plug from the power source before making any adjustments, changing accessories or storing the tool. Such preventive safety measure reduce the risk of starting the tool accidentally. 5. Never leave the tool running. Always turn it off. Do not leave the tool until it comes to a complete stop. 6. Store idle tools out of the reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. 7. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edges are less likely to bind and are easier to control. 8. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation. If damaged, have the tool serviced TOOL USE AND CARE SAFETY than using your hand and frees both hands to operate tool. 9. Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions. 10. Do not use on a ladder or unstable support. Stable footing on a solid surface enables better control of the tool in unexpected situations. SAFETY INSTRUCTIONS 3. Before plugging in the tool, be sure that the outlet voltage supplied is within the voltage marked on the tool’s data plate. Do not use “AC only” rated tools with a DC power supply. 4. Avoid body contact with grounded Double insulation does not take the place of normal safety precautions when operating this tool. WARNING: Cover of Grounded Outlet Box 1. Double insulated tools are equipped with a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way. 2. Double insulation eliminates the need for the three-wire grounded power cord and grounded power supply system. Applicable only to Class II (double-insulated) tools. This power tool is a double-insulated tool WARNING: Do not permit fingers to to touch the terminals of plug when installing or removing the plug from the outlet. ELECTRICAL SAFETY before using. Many accidents are caused by poorly maintained tools. 9. Use only accessories that are recommended for this tool. Accessories that may be suitable for one tool may become hazardous when used on another tool. 10 12 16 6 10 12 14 16 18 18 12 16 16 16 12 12 14 Page 6 Not Recommended 14 14 16 25ft. 50ft. 100ft. 150ft. 6 More Than< >Less Than 0 Total Length Of Cord Ampere Rating (When using 120 volts only) MINIMUM GAUGE FOR EXTENSION CORDS Use a proper extension cord. Only use cords listed by Underwriters Laboratories (UL). Other extension cords can cause a drop in line voltage, resulting in a loss of power and overheating of tool. When operating a power tool outdoors, use an outdoor extension cord marked “W-A” or “W”. These cords are rated for outdoor use and reduce the risk of electric shock. before each use. If damaged replace immediately. Never use tool with a damaged cord since toughing the damaged aread could cause electrical shock, resulting in serious injury. WARNING: Check extension cords CAUTION: Keep the extension cord clear of the working area. Position the cord so that it will not get caught on lumber, tools or other obstructions while you are working with a power tool. EXTENSION CORDS surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. 5. Do not expose power tools to rain or wet conditions or use power tools in wet or damp locations. Water entering a power tool will increase the risk of electric shock. 6. Do not abuse the cord. Never use the cord to carry the tool by or pull the plug from the outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock. SAFETY INSTRUCTIONS Tool Gauge Regulator Ouick Couplers 207-1522 120 V, 60 Hz, Induction 2.0 HP 13 A 5.0 U.S. gallons 6.0 5.0 160 200 Oil-free, Direct Drive SJ14 x 12ft 78 lbs (35.4 kg) SPECIFICATIONS Drain Valve Cam Locks Pressure Switch Power Cord Item#: Motor: Running Horsepower: Amperes: Tank Size: Air Delivery (CFM*)@40 PSI: Air Delivery (CFM*)@90 PSI: Cut-in Pressure(PSI): Cut-out Pressure(PSI): Pump Design: Power Cord: Weight: Sliding Handle Tank Safety Valve (Not Visible) OVERVIEW Page 7 Motor & Pump This manual contains important safety and operating instructions. Read all instructions and follow them with use of this product. SAVE THESE INSTRUCTIONS Air Hammer Cut-Off Tool Air Drill Flooring Nailer Framing Nailer Spray Gun (30-70 PSI) Finish Nailer Ratchet Impact Wrench The cam lock is used to lock the sliding handle. Cam lock This handle is height adjustable for easier mobility. Sliding handle Page 9 This compressor should be used on a nominal 120V grounded circuit. Use a power cord that is equipped with a grounding plug. Verify that the compressor is plugged into an outlet that has the same configuration as the plug. Do not use an adaptor with this compressor. Power cord The tank is where the compressed air is stored. Air tank The ball valve is used to remove moisture from the air tank after the compressor is shut off. Air tank drain valve The couplers is connected to the 1/4” (6.4 mm) NPT air hose. Quick couplers The gauge measures the regulated outlet pressure. Tool pressure gauge The gauge measures the pressure level of the air that is stored in the tank. It cannot be adjusted by the operator and it does not indicate the pressure inside the line. Tank pressure gauge The regulator is used to adjust the pressure inside the line to the tool that is being used. Turn the knob clockwise to increase the pressure and counter-clockwise to decrease the pressure. Air pressure regulator This switch turns the compressor on and off manually. ALWAYS set this switch to the OFF position when the compressor is not being used and before unplugging. Pressure Switch This valve is used to prevent the compressor from building too much pressure. If the pressure reaches the preset level of the motor, it will automatically pop open. You can also pull the ring on the valve to open manually. Safety Valve Grease Gun Electric motor and pump PRODUCT FEATURES Always ensure the use of appropriately matched air tools with your Air Compressor. Be sure that the air compressor being used can supply the appropriate volume, pressure and delivery rate of air to the tool(s) without running continuously. Using tools or combinations of tools that, together or separately, require more than the air compressor can deliver will void the air compressor guarantee/warranty. Compatible compressor and air tool - proper usage and operation The motor is used to power the pump. The pump is used to compress the air and discharge it into the tank via the piston moving up and down in the cylinder Page 8 Operates Tool Operates Tool No Continuously Intermittently Recommended This Air Compressor is ideal for a wide range of applications from fastening to greasing and engine cleaning. The 5 gallon design provides optimum pressure. It features a 2.0 HP induction motor for quiet operation and a cast-iron, oil-less pump for long-lasting, reliable performance. The procedures described in this manual are solely for this gallon air compressor at a maximum of P=200 PSI. The device has been designed and constructed for household use only. Important Information Screwdriver Spray Gun (20-45 PSI) Brad Nailer Nailer/Stapler Cleaning Caulking Air Brush Inflation/Recreational Air Tool Tool Compatibility Chart 1 FIG. A 2 3 4. Connect the air hose (1) to the compressor’s air outlet (2) with the quick connector (3)(FIG B). FIG. B 2 3 1 Page 10 Note: Attach air hose and accessories (not provided). Apply plumber’s tape on all the threads to prevent air leakage. Connect air hose to compressor 1. Position the air compressor (1) near an electrical out (2)(FIG. A). 2. The compressor must be at least 12”(31cm) from any wall (3) or abstruction, in a clean, well-ventilated area to ensure sufficient air flow and cooling(FIG A). 3. Place the air compressor on the floor or a hard, level surface. The air compressor must be level to ensure proper drainage of the moisture in the tank. 1 Owner’s manual ILLUSTRATION Positioning of the air compressor 1 QTY Air compressor DESCRIPTION Product Features Check the air compressor’s identification label to ensure that you have purchased the intended model and that it has the required pressure rating for its intended use. Unpack the air compressor unit. Inspect the unit for damage. If the unit has been damaged, contact the retailer immediately. Assembly Instructions OFF FIG. D 1. Set the pressure switch(1) to the OFF position (Fig D). FIG. C Before starting compressor, pull the ring on the safety valve to make sure that the safety valve operates freely. If the valve is stuck or does not operate smoothly, contact a trained service technician(Fig C). Check Safety Valve If the pump has been transported or turned upside down (even partially), allow the pump to sit in a normal, upright position for approximately 10 minutes before starting. Notice WARNING: Hot compressor surfaces could result in serious injury. Allow compressor to cool before touching. WARNING: High pressure air could result in death or serious injury. Never operate above maximum operating pressure of the spray gun or tool. FIG. F Page 11 3. Attach hose (1) and accessories (FIG F). FIG. E 2. Turn the air pressure regulator knob counter-clockwise until it stops(Fig E). Operating Instructions 2 ON OFF 1 ON 1. Set the pressure switch (1) to the OFF position. 2. Unplug the power cord (2). 3. Reduce the pressure in the tank through the outlet hose. Pulling the safety valve ring (3) and keeping it open will also reduce the pressure in the tank(fig I). 4.Set tank drain valve(4)(fig I) to OFF to ensure tank is drained. Shut down FIG. H 6. Set the pressure switch to the ON position and allow the tank pressure to build. Motor will stop when tank pressure reaches cut-out pressure(Fig H). FIG. G 5. Close the tank drain valve (1) . Plug-in the power cord(2)(Fig G) 4 2 OFF 1 ON Page 12 1. Set the pressure switch to the O (OFF) position. 2. Turn air pressure regulator knob counter-clockwise to set the outlet pressure to zero. 3. Pull and hold ring on safety valve, allowing air to bleed from the tank until air pressure is minimized. 4. Place a suitable container under the unit to catch any water. 5. Slightly tilt unit and turn drain valve counter-clockwise to open. 6. After the water has been drained,close the ball valve(clockwise). The air compressor can now be stored. Drain the tank CAUTION: High pressure air containning water condensation could result in minor or moderate injury. Do not spray at any person. WARNING: High pressure air could result in death or serious injury. Shut off unit, unplug and release air pressure prior to servicing. WARNING: Risk of serious eye injury from moisture and debris. Always wear ANSI Z87.1 safety goggles when opening drain valve. 3 FIG. I Operating Instructions Storage Test for leaks Check the valve Drain the tank ITEM Before storing the air compressor compressor: Drain tank (page 12). Use an air blow gun to clean all dust and debris from the pressor. Disconnect and wind up the power cord. Clean the ventilation openings on the motor enclosure with a damp cloth. Drain all moisture from the tank. Pull the pressure safety valve to release all pressure from the tank. Cover the entire unit to protect it from moisture and dust. Store the air compressor in a clean and dry location. In cold weather, store the compressor in a warm building when it is not in use. This will reduce problems related to starting the motor and the freezing of water condensation. Check that all connections are tight. Small leaks in the tank, hoses,connections or transfer tubes will substantially reduce the air compressor and tool performance. Spray a small amount of soapy water around the area of suspected leaks with a spray bottle. If bubbles appear, repair: replace or reseal the faulty component. Do not over-tighten any connections. Pull/actiate the safety valve daily to ensure that it is operating properly and to clear the valve of any possible obstructions. Through normal operation of your air compressor, condensationwater will accumulate in the tank. To prevent corrosion of the tank from the inside, condensation must be drained at the end of every workday. Be sure to wear protective goggles. Relieve the air pressure in the system then open the drain valve on the bottom of the tank to drain. Under cold conditions it is especially important to drain the tank after each use to reduce the chance of problems resulting from the freezing of condensation water. NOTE: Refer to instructions on how to drain tank (page 12). DESCRIPTION / REASON Maintenance Page 13 Prior to storing Monthly Daily Daily SERVICE INTERVAL The regulator does not regulate the pressure. Disconnect any other electrical appliances from the circuit or operate the compressor on a dedicated circuit. Check for low voltage conditions. Replace the fuse or reset the circuit breaker. Verify that the fuse has the proper amperage. Contact an authorized service center. Contact an authorized service center. Electrical connections are lose. The motor, capacitor, or safety valve is defective. The regulator or its internal parts are dirty or damaged. The compressor’s capacity is not enough. Replace the regulator. Page 14 Check the air requirements of the accessory that is being used. If it is higher than the CFM (Cubic Feet per Minute )and pressure supplied by the compressor (page 7), a larger capacity air compressor is needed. Most accessories are rated at 25% of actual CFM while running continuously. Set the pressure switch to the OFF position. If the motor does not shut off, unplug the air compressor. If the pressure switch is defective, replace it. Clean or replace the safety valve. The safety valve is stuck open. The air tank pressure exceeds The motor will start automatically when the the preset pressure switch limit. tank pressure drops below the cut-in pressure. A fuse has blown or a circuit breaker has been tripped. The motor’s thermal overload protection has tripped. Check extension cord information (page 6) for the proper wire gauge and cord length. The extension cord is the wrong wire gauge or is too long. Turn the air compressor off, unplug the power cord and wait until the motor has cooled down. Plug in the power cord only after the motor has cooled down, and wait wait at least 5 minutes to make sure the thermal overload protector has recovered. Set the power switch to the ON position. The power switch is in the OFF position. The pressure switch does not shut off the motor when the air The motor runs compressor reaches the cut-out pressure and the safety valve continuously activates. when the pressure switch is in the ON position. The motor will not run or start SOLUTIONS The power cord is not plugged in. Plug the power cord into a grounded outlet. PROBLEM POSSIBLE CAUSE Troubleshooting The compressor overheats. There is moisture in the discharge air. Page 15 Replace worn parts and reassemble using new plumber's tape. Clean all cooling surfaces on the pump and the motor thoroughly. Cooling surfaces are dirty. The valve is leaking. Relocate the compressor to an area with cool, dry and well-circulated air. Drain the air tank after each use. Drain the air tank more often in humid weather and use an air-line filter. There is condensation in the air tank caused by a high level of atmospheric humidity or because the air compressor has not been running long enough. The ventilation is inadequate. Check for worn parts and replace them if necessary. Replace the tank immediately. Do not attempt to repair it. Check the air hose and replace it if necessary. Decrease the amount of air used. Clean or replace the air filter element. Close the drain valve. Check the fittings with soapy water. Tighten or reseal leaking fittings (apply plumber’s tape on threads). Do not over tighten. SOLUTIONS The valve is leaking. The tank leaks. The tank drain valve is open. The pressure The air intake is restricted. is low or there is not Prolonged excessive use of air. enough air. There is a hole in the air hose. There is a leak at one of the fittings. PROBLEM POSSIBLE CAUSE Troubleshooting Exploded View Page 16 Item# 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 Part No. X4561020199 J3264540042 J3894550069 J2020530033 Q3762988001 Q3766378001 J0200580003 Q3766398001 J0800470033 J0800500033 X4590590205 J0902530037 F1513700621 J0180380037 J3134560201 X0060590091 Q4474318001 J0994580201 J0801100033 J0024020201 F5013700623 J0782730032 Q4562111001 J2992050037 J0800960033 J3163780034 F9913700343 F3013700624 J6014570170 J3090980171 Q4594328001 A2830260480 J2022870040 X4596840206 D1015068139 D3005000067 J3122050032 F4813700643 J6500920028 J0807310040 Q3766408007 Q3766388001 J0780600033 Description Handle Grip Sliding Handle Latch Lock Nut Wahser Cam Lock Assembly 1 Spring Adjustment Cap Bolt M6X34 Bolt M6X16 Rubber Foot Drain Valve Tank Check Valve Bleeding Tube Cushion Pad Front Shroud Flexible Tube Bolt M5X12 Relief Valve Pressure Gauge Screw M4X10 Regulator Knob Quick Coupler Bolt M5X12 Right Elbow Rubber Hose Regulator Control Panel Air Filter Rear Shroud Motor and Pump Nut M8 Rubber Pad Power Cord Pressure Switch Plug Wheel Cotter Pin Bolt M8X20 Sleeve Cam Lock Assembly 2 Screw M8X8 Parts List Qty 1 1 2 2 2 1 2 2 2 6 2 1 1 1 1 3 1 1 9 1 2 1 1 2 2 1 1 1 1 1 1 1 3 2 1 1 2 2 2 3 2 1 2 Page 17 NOTES Page 18 Page 19 SAVE YOUR RECEIPTS THIS WARRANTY IS VOID WITHOUT THEM For questions / comments, technical assistance or repair parts Please call toll free at: 1-888-899-0146 (M-F 8am-5pm CT) This MASTERFORCE™ brand power tool carries our famous No Hassle 3-Year Limited Warranty to the original purchaser. If, during normal use, this MASTERFORCE™ power tool breaks or fails due to a defect in material or workmanship within one (1) year from the date of original purchase, simply bring the tool with the original sales receipt back to your nearest MENARDS® retail store. At its discretion, MASTERFORCE™ agrees to have the tool or any defective part(s) repaired or replaced with the same or similar MASTERFORCE™ product or part free of charge, within the stated warranty period, when returned by the original purchaser with original sales receipt. Not withstanding the foregoing, this limited warranty does not cover any damage that has resulted from abuse or misuse of the Merchandise. This warranty: (1) excludes expendable parts including but not limited to blades, brushes, belts, bits, light bulbs, and/or batteries; (2) shall be void if this tool is used for commercial and/or rental purposes; and (3) does not cover any losses, injuries to persons/property or costs. This warranty does give you specific legal rights and you may have other rights, which vary from state to state. Be careful, tools are dangerous if improperly used or maintained. Seller’s employees are not qualified to advise you on the use of this merchandise. Any oral representation(s) made will not be binding on seller or its employees. The rights under this limited warranty are to the original purchaser of the merchandise and may not be transferred to any subsequent owner. This limited warranty is in lieu of all warranties, expressed or implied including warranties or merchantability and fitness for a particular purpose. Seller shall not be liable for any special, incidental, or consequential damages. The sole exclusive remedy against the seller will be for the replacement of any defects as provided herein, as long as the seller is willing or able to replace this product or is willing to refund the purchase price as provided above. For insurance purposes seller is not allowed to demonstrate any of these power tools for you. 3-YEAR LIMITED WARRANTY WARRANTY 5 Gallon Air Compressor © 2015 Menard, Inc., Eau Claire, WI 54703 11/2015 ">
/
Letöltés
Csak egy baráti emlékeztető. A dokumentumot itt is megtekintheti. De ami a legfontosabb, a mi AI-nk már elolvasta. Egyszerűen el tudja magyarázni a bonyolult dolgokat, bármilyen nyelven megválaszolja kérdéseit, és segít gyorsan navigálni a leghosszabb vagy legbonyolultabb dokumentumokban is.
Hirdetés