advertisement
Contents
1. Precautions
●
Storage and Keeping
1.
Do not expose the monitor to excessive heat or cold. The storage temperature of this device is
2.
3.
4.
5.
6.
7.
8.
9.
-30~+80℃, and the operating temperature is -20~+70 ℃. The humidity is RH90%
Never use this device near a bathtub, wash basin, kitchen, damp basement, swimming pool or similar places.
Never use this device in environments with excessive moisture, dust or smoke.
Avoid dropping or striking this device.
Avoid using this device in enclosed spaces, areas with excessive vibration or subject to severe impacts.
Never puncture, scratch or use abrasive cleaning materials on this device.
Do not place cables where they may be pinched or stepped on.
Leave at least a 2" space between the monitor and walls, cabinets or other objects to allow adequate air circulation around the device.
The monitor is not designed to be waterproof.
●
Operating Precautions
1. The device may be powered by a 12 or 24 volt automotive battery or vehicle electrical system.
2.
Make sure all cables are connected properly. Observe polarity. Improper cable connections may damage the monitor. Remove the power cable connections when you do not intend to use the unit.
Warning!
1. High voltage is present within the monitor. The opening of the case should be by professionals.
2. Do not watch the video while driving unless you are monitoring the rear view camera display.
Special Notice
Occasionally, a few highlights or dark spots may occur on the LCD screen. This is a very common phenomenon in active matrix display technology, and doesn't necessarily indicate any defects or faults.
Never try to repair this device by yourself. In case of any problems, please turn off the display at once and notify our company or authorized dealer. The monitor is a complex device. Any disassembly or modification may lead to damage and void the warrantee.
-1-
.
●
Maintenance
1. Remove all the cable connections from the monitor before cleaning the device.
2. Use a mild household detergent and clean the unit with a slightly damp, soft cloth.
3. Never use strong solvents such as thinner or benzine, as they might damage the finish of the device.
Caution
Risk of electric shock
Do not open
Caution: to reduce the risk of electric shock,
Do not remove cover (or back).
No user-serviceable parts inside.
Refer servicing to qualified service personnel.
This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
This symbol is intended to alert the user not to dispose of electrical and electronic equipment
CAUTION
You are cautioned that any changes or modifications not expressly approved in this manual could void your warrantee and neccessitate expensive repairs.
●
Declaration of conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: la FCC (Comisión Federal de Comunicaciones). El funcionamien to está sujeto a dos condiciones:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
-2-
2. Product Features
1. TFT LCD monitor with wide angle view and high resolution display.
2. Picture image may be adjusted for Horizontal, Vertical, Mirror and Normal viewing.
3. Select from 8 languages for user operation.
4. Automatic back lighting for buttons.
5. Full-function remote control.
6. Multiple video formats: PAL/AUTO/NTSC.
7. Up to 4 wireless camera input,1video output and 1 audio output.
8. Operates from 10 -32V. Supports 12V or 24V automobile battery.
9. On-board speaker.
10. Automatic scanning function..
11. The scale can be adjusted for left, right, up and down.
12. Automatically switches to back-up,left,right or front camera views.
3. Technical Specifications
1. 7" TFT- LCD Color monitor with digital panel.
2. Audio output: 1.5 W.
3. Loudspeaker: one 15x24mm round loudspeaker.
4. Power supply: Automobile storage battery (DC / 10-32V).
5. Power consumption: about 6W.
6. Outer dimension: 182mm (W) × 122mm )H( × 26mm )T( (without flush mount), 198mm (W) × 138mm
(H) × 31mm (T) (with flush mount).
7. Dot pitch: 0.0642(W) x 0.1790(H).
8. Resolution: 800×3 (RGB) × 480.
9. Contrast: 500:1.
10. Brightness: 400cd/m2.
11. Viewing angle: U: 50° / D: 70°, R/L: 70°/70°.
12. Operating temperature: -20~+70ºC, RH90%.
13. Storage temperature: -30~+80ºC, RH90%.
Special Notice
All specifications are subject to change without notice.
-3-
4. Accessories
U- Support Bracket Optional
AV and Power supply adapter cable
Sun Shield
Angle adjustment screws
Flush Mount(optional)
Center Mount Bracket
IR Remote Control
Detaching Piece
Front Panel AV Input adapter
Special Notice
Accessory supply may be different for different application.
-4-
6. Remote Control Operation
Mute
Horizontal Flip
Setting Selection Up
Less Brightness
Setting Selection Down
Power Switch
Vertical Flip
Menu
More Brightness
Call
Timer
Picture Mode
Select
CAM1/CAM2/
CAM3/CAM4
Language Selection
PAL/AUTO/NTSC
Notice
1. Please align the remote control with the infrared-receiving window on the monitor to operate.
2. Never disassemble the remote control or allow it to drop, or become wet.
3. Press the control buttons firmly. Allow 2 seconds for the picture to change.
-6-
●
MUTE (Mute):
Press to select ENABLE/MUTE sound.
●
POWER(Power switch)
Press to turn on/off the monitor.
●
(Horizontal Turning of Picture):
Press to turn picture horizontally.
●
(Vertical Turning of Picture):
Press to turn picture vertically.
●
CH+ (Channel Selection Up):
Press to select the upper setting.
●
CH- (Channel Selection Down):
Press to select the lower setting or to display the scale.
●
Press to decrease Brightness.
●
Press to increase Brightness.
●
MENU:
Press to show menu.
●
MODE (Picture Mode):
Press to select different picture modes (PERSONAL / STANDARD / SOFT / VIVID / LIGHT).
●
CALL (Call)
Press to display video channel source.
●
TIMER:
Press to set the timer to shut down monitor (10, 20, 30, 40 and max 90 minutes).
●
LANG (Language Selection):
Press to select language display of English, Deutsch, Franiçais, Español, Português, Italiano, Nederlands or
Русский options.
●
SYS:
Press to select PAL / AUTO / NTSC.
●
SEL
Press to select CAM channels
-7-
Black 4/5 pin male for Camera 1 / Camera 2 / Camera 3 / Camera 4.
Single red wire to positive power supply of DC/10-32V.
Single black wire to GND.
Single brown wire to positive power wire of back-up light.
Single white wire to positive power wire of left light.
Single blue wire to positive power wire of right light.
Single green wire to any other trigger control.
Black 22 male
Black 22 pin female
Yellow RCA female
White RCA female
Brown 4/5 pin male
Blue 4 pin male
White 4 pin male
Green 4 pin male
7.3. Removing the Monitor:
Yellow RCA female for video output .
White RCA female for audio output.
Yellow RCA male
White RCA male
Red
White
Black
Blue
Brown
Green
7.3.2. Remove the monitor.
7.3.1. Insert the detaching piece as indicated by the white arrow. Press in and lift up, the monitor will be released from the flush mount.
7.4. Reversing Display:
7.4.1. When the white wire is connected to the positive wire of the left turn light , the monitor automatically switches to CAM1 (left side camera) when the left turn indicator is activated.
7.4.2. When the blue wire is connected to the positive wire of the right turn light, the monitor automatically switches to CAM2 (right side camera) when the right turn indicator is activated.
Flush mount
CAM1
CAM2
Camera
Black 22 pin female
Digital Color LCD screen
-9-
7.4.3. When the brown wire is connected to the positive wire of back-up light, the monitor automatically switches to CAM 3 (back-up camera) when the back-up light is turned on. The distancing grid will also be displayed.
7.4.3. 7.4.4.When the green wire is activated,the monitor automatically switches to CAM4.
8. Menu
●
Press MENU to display the following options and settings:
1. PICTURE
CAM4
2. OPTION
3. SYSTEM
4. AUTO SCAN
(1) Picture
VOLUME, BRIGHT, CONTRAST, COLOR, AUTO DIM and SCALE ADJUST options will display on the screen as illustrated below:
●
Press CH- to select BRIGHT.
PICTURE
BRIGHT
CONTRAST
COLOR
VOLUME
AUTO DIM
SCALE ADJUST
50
50
50
50
OFF
OFF
Press adjust the brightness Level.
-10-
●
When auto dim is turned on in dark environment, OSD turns into dim mode for dim setting; When auto dim is turned on / off in bright environment, OSD displays normal mode.
PICTURE
BRIGHT
CONTRAST
COLOR
VOLUME
AUTO DIM
SCALE ADJUST
40
45
40
50
ON
OFF
PICTURE
BRIGHT
CONTRAST
COLOR
VOLUME
AUTO DIM
SCALE ADJUST
50
50
50
50
ON
OFF
●
Press CH- to select SCALE ADJUST.
PICTURE
BRIGHT
CONTRAST
COLOR
VOLUME
AUTO DIM
SCALE ADJUST
50
50
50
50
ON
OFF
●
Exit menu and again press CH- to display the grid line
to adjust the scale up/down; If is selected press If is selected, press to adjust the scale left/right.
-11-
(2) OPTION
LANG, SCALE, CAM1 CAM2 CAM3 CAM4 PAIRING, options display on the screen as illustrated below:
●
Press CH- to select LANG.
OPTION
LANG
SCALE
CAM1
CAM2
CAM3
CAM4
English
ON
Normal
Normal
Normal
Normal
Press to select English, Deutsch, Français,Español,Português, Italiano, Nederlands or Русский options.
●
Press CH- to select Scale.
OPTION
LANG
SCALE
CAM1
CAM2
CAM3
CAM4
English
ON
Normal
Normal
Normal
Normal
Press on the monitor.
to select ON / OFF. Scale refers to the reversing distance indicator displayed
●
Press CH- to select CAM1.
OPTION
LANG
SCALE
CAM1
CAM2
CAM3
CAM4
English
ON
Normal
Normal
Normal
Normal
Press to select NORMAL / MIRROR.
-12-
(3) System
COLOR-SYS, HORIZONTAL, VERTICAL, ZOOM functions will display on the screen as illustrated below:
●
Press CH- to select COLOR-SYS.
SYSTEM
COLOR-SYS
BLUE BACK
HORIZONTALl
VERTICAL
ZOOM
AUTO
ON
16:9
Press to select PAL / AUTO / NTSC.
●
Press CH- to select BLUE BACK.
SYSTEM
COLOR-SYS
BLUE BACK
HORIZONTALl
VERTICAL
ZOOM
AUTO
ON
16:9
Press to select ON/OFF
●
Press CH- to select ZOOM.
SYSTEM
COLOR-SYS
BLUE BACK
HORIZONTALl
VERTICAL
ZOOM
AUTO
ON
16:9
Press to select 16:9 or 4:3..
-13-
(4) Auto Scan
AUTO SCAN, SCAN TIME, CAM1, CAM2, CAM3 and CAM4 options display on the screen as illustrated below:
●
Press CH- to select SCAN TIME.
Press
AUTO SCAN
AUTO SCAN
SCAN TIME
CAM1
CAM2
CAM3
CAM4
to select 1S~90S.
OFF
5S
OFF
OFF
OFF
OFF
9. Troubleshooting
The symptoms described below do not necessarily mean a failure within the display. Please check the following items before you initiate request for repair.
No picture, no sound
No picture
No sound
Dark picture
Symptoms
No color
Upside down or lateral inverted picture
No reversing function
(i.e.Picture)
Possible Causes/Solutions
Improper connection of automobile adapter. Use of unauthorized power supply. Power switch is on OFF position.
Check whether AV cable is properly connected.
Check whether audio wire is properly connected or the sound volume is turned off or set too low.
Check whether brightness and contrast are adjusted correctly;
Check whether the environments temperature is too low.
Adjust the color settings.
Use the remote control horizontal /vertical selection switch to set proper orientation.
The black wire of the monitor AV cable to the reversing light may be loose. The red wire from the monitor may be loose.
-14-
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement