DeWalt DCD932 CORDLESS DRILL instruction manual

DCD932
DCD937
DCD990
DCD995
FINAL PRINT SIZE: A5 (148mm x 210mm)
English (original instructions)3
Copyright DeWALT
B
Figure 1
e
d
f
g
b
a
DCD990
c
i
l
k
i
j
h
h
Figure 2
h
i
m
1
Figure 3
Figure 4
Figure 5
e
e
f
f
Figure 7
Figure 6
Figure 8
d
Figure 9
g
n
2
English (original instructions)
English
BRUSHLESS CORDLESS 13 mm (1/2")
DRILL/DRIVER, DCD932, DCD990
BRUSHLESS CORDLESS 13 mm (1/2")
DRILL/DRIVER/HAMMERDRILL, DCD937, DCD995
Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough product development and innovation make
DeWALT one of the most reliable partners for professional power tool users.
Technical Data
DCD932 DCD937 DCD990 DCD995
Voltage
VDC 14.4 14.4 1818
Type
1/10
1/10
1/10
1/10
Battery Type
Li-Ion
Li-Ion
Li-Ion
Li-Ion
Power output
W
520
520
650
650
No-load speed
1st gear
min-1 0–420 0–420 0–4500–450
2nd gear
min-1
0–1250 0–1250 0–13000–1300
3rd gear
min-1
0–1850 0–1850 0–20000–2000
Impact rate
1st gear
min-1
– 0–7140 –0–7650
2nd gear
min-1
– 0–21250 –0–22100
3rd gear
min-1
– 0–31450 –0–34000
Max. torque (hard/soft)
Nm
75/38
75/38
80/42
80/42
Chuck capacity
mm
1.5–13
1.5–13
1.5–13
1.5–13
Maximum drilling capacity
Wood
mm
45
45
50
50
Metal
mm
13
13
13
13
Masonry
mm
–
14
–
16
Weight (without battery pack)
kg
1.5
1.55
1.5
1.55
Noise values and vibration values (triax vector sum) according to EN 60745-2-2:
LPA (emission sound pressure level)
dB(A)
71 92 7192
LWA (sound power level)
dB(A)
82 103 82103
K (uncertainty for the given sound level)
dB(A)
3 3 33
Drilling into metal
Vibration emission value ah,D =
Uncertainty K = Impact drilling
Vibration emission value ah,ID =
Uncertainty K = Screwdriving
Vibration emission value ah =
Uncertainty K = m/s²
m/s²
2.7
1.5
2.7 2.72.7
1.5 1.51.5
m/s²
m/s²
– 10.5 –10.5
– 1.5 –1.5
m/s²
m/s²
< 2.5
< 2.5
< 2.5
< 2.5
1.5 1.5 1.51.5
3
English
The vibration emission level given in this information
sheet has been measured in accordance with a
standardised test given in EN60745 and may be
used to compare one tool with another. It may be
used for a preliminary assessment of exposure.
WARNING: The declared vibration
emission level represents the main
applications of the tool. However if the
tool is used for different applications,
with different accessories or poorly
maintained, the vibration emission may
differ. This may significantly increase the
exposure level over the total working
period.
An estimation of the level of exposure to
vibration should also take into account
the times when the tool is switched off
or when it is running but not actually
doing the job. This may significantly
reduce the exposure level over the total
working period.
Identify additional safety measures to
protect the operator from the effects of
vibration such as: maintain the tool and
the accessories, keep the hands warm,
organisation of work patterns.
Battery pack
Battery type
Voltage
Capacity
Weight
Battery pack
Battery type
Voltage
Capacity
Weight
Battery pack
Battery type
Voltage
Capacity
Weight
Battery pack
Battery type
Voltage
Capacity
Weight
4
VDC
Ah
kg
DCB140
Li-Ion
14.4
3.0
0.53
DCB141
Li-Ion
14.4
1.5
0.30
DCB142
Li-Ion
14.4
4.0
0.54
VDC
Ah
kg
DCB143
Li-Ion
14.4
2.0
0.30
DCB144
Li-Ion
14.4
5.0
0.52
DCB145
Li-Ion
14.4
1.3
0.30
VDC
Ah
kg
DCB180
Li-Ion
18
3.0
0.64
DCB181
Li-Ion
18
1.5
0.35
DCB182
Li-Ion
18
4.0
0.61
VDC
Ah
kg
DCB183/B
Li-Ion
18
2.0
0.40/0.45
DCB184/B
Li-Ion
18
5.0
0.62/0.67
DCB185
Li-Ion
18
1.3
0.35
Charger
Mains voltage
Battery type
Approx. charging time
of battery packs
VAC
min
DCB105
230
10.8/14.4/18 Li-Ion
25 (1.3 Ah) 30 (1.5 Ah) 40 (2.0 Ah)
55 (3.0 Ah) 70 (4.0 Ah) 90 (5.0 Ah)
0.49
Weight
kg
Charger
Mains voltage
Battery type
Approx. charging time
of battery packs
DCB107
230
10.8/14.4/18 Li-Ion
min 60 (1.3 Ah) 70 (1.5 Ah) 90 (2.0 Ah)
140 (3.0 Ah) 185 (4.0 Ah) 240 (5.0 Ah)
kg
0.29
Weight
Charger
Mains voltage
Battery type
Approx. charging time
of battery packs
Weight
VAC
VAC
min
kg
Charger
Mains voltage
Battery type
Approx. charging time
of battery packs
Weight
VAC
min
kg
Charger
Mains voltage
Battery type
Approx. charging time
of battery packs
VAC
min
DCB112
230
10.8/14.4/18 Li-Ion
40 (1.3 Ah) 45 (1.5 Ah) 60 (2.0 Ah)
90 (3.0 Ah) 120 (4.0 Ah) 150 (5.0 Ah)
0.36
DCB113
230
10.8/14.4/18 Li-Ion
30 (1.3 Ah) 35 (1.5 Ah) 50 (2.0 Ah)
70 (3.0 Ah) 100 (4.0 Ah) 120 (5.0 Ah)
0.4
DCB115
230
10.8/14.4/18 Li-Ion
25 (1.3 Ah) 30 (1.5 Ah) 40 (2.0 Ah)
55 (3.0 Ah) 70 (4.0 Ah) 90 (5.0 Ah)
0.5
Weight
kg
Fuses:
Europe
U.K. & Ireland
230V tools
230V tools
10 Amperes. mains
3 Amperes. in plugs
Definitions: Safety Guidelines
The definitions below describe the level of severity
for each signal word. Please read the manual and
pay attention to these symbols.
DANGER: Indicates an imminently
hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING: Indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
English
CAUTION: Indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
NOTICE: Indicates a practice not
related to personal injury which, if
not avoided, may result in property
damage.
Denotes risk of electric shock.
Denotes risk of fire.
EC-Declaration of Conformity
MACHINERY DIRECTIVE
DRILL/DRIVER/HAMMERDRILL
DCD932, DCD937, DCD990, DCD995
DeWALT declares that these products described
under Technical Data are in compliance with:
2006/42/EC, EN60745-1:2009+A11:2010,
EN60745-2-1:2010, EN60745-2-2:2010.
These products also comply with Directive
2004/108/EC (until 19.04.2016), 2014/30/EU (from
20.04.2016) and 2011/65/EU. For more information,
please contact DeWALT at the following address or
refer to the back of the manual.
The undersigned is responsible for compilation of
the technical file and makes this declaration on
behalf of DeWALT.
Markus Rompel
Director Engineering
DeWALT, Richard-Klinger-Straße 11,
D-65510, Idstein, Germany
08.08.2015
WARNING: To reduce the risk of injury,
read the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings
and all instructions. Failure to follow
the warnings and instructions may result
in electric shock, fire and/or serious
injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or batteryoperated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There
is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric
shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
5
English
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your finger
on the switch or energising power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce
dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it
was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
6
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and
tool bits etc., in accordance with these
instructions taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified
by the manufacturer. A charger that is
suitable for one type of battery pack may
create a risk of fire when used with another
battery pack.
b) Use power tools only with specifically
designated battery packs. Use of any
other battery packs may create a risk of
injury and fire.
c) When battery pack is not in use, keep it
away from other metal objects like paper
clips, coins, keys, nails, screws or other
small metal objects that can make a
connection from one terminal to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery, avoid contact.
If contact accidentally occurs, flush with
water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6) SERVICE
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Additional Specific Safety Rules for
Drills/Drivers/Hammerdrills
• Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
English
• Use auxiliary handles, if supplied with the
tool. Loss of control can cause personal injury.
• Hold power tool by insulated gripping
surfaces when performing an operation
where the cutting tool may contact hidden
wiring. Cutting accessory contacting a “live”
wire may make exposed metal parts of the
power tool “live” and could give the operator an
electric shock.
• Use clamps or other practical way to secure
and support the workpiece to a stable
platform. Holding the work by hand or against
your body is unstable and may lead to loss of
control.
• Wear ear protectors when hammering
for extended periods of time. Prolonged
exposure to high intensity noise can cause
hearing loss. Temporary hearing loss or serious
ear drum damage may result from high sound
levels generated by hammerdrilling.
DATE CODE POSITION
The Date Code, which also includes the year of
manufacture, is printed into the housing surface that
forms the mounting joint between tool and battery.
Example:
2015 XX XX
Year of Manufacture
Important Safety Instructions for All
Battery Chargers
SAVE THESE INSTRUCTIONS: This manual
contains important safety and operating
instructions for compatible battery chargers (refer to
Technical Data).
• Before using charger, read all instructions and
cautionary markings on charger, battery pack,
and product using battery pack.
• Wear safety goggles or other eye protection.
Hammering and drilling operations cause chips
to fly. Flying particles can cause permanent eye
damage.
WARNING: Shock hazard. Do not allow
any liquid to get inside charger. Electric
shock may result.
WARNING: We recommend the use of
a residual current device with a residual
current rating of 30mA or less.
• Hammer bits and tools get hot during
operation. Wear gloves when touching them.
CAUTION: Burn hazard. To reduce
the risk of injury, charge only DeWALT
rechargeable batteries. Other types of
batteries may burst causing personal
injury and damage.
CAUTION: Children should be
supervised to ensure that they do not
play with the appliance.
Residual Risks
The following risks are inherent to the use of
percussion drills:
– Injuries caused by touching the rotating parts or
hot parts of the tool.
In spite of the application of the relevant safety
regulations and the implementation of safety
devices, certain residual risks cannot be avoided.
These are:
– Impairment of hearing.
– Risk of squeezing fingers when changing
accessories.
– Health hazards caused by breathing dust
developed when working in wood.
– Risk of personal injury due to flying particles.
– Risk of personal injury due to prolonged use.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
NOTICE: Under certain conditions, with
the charger plugged into the power
supply, the exposed charging contacts
inside the charger can be shorted by
foreign material. Foreign materials of
a conductive nature such as, but not
limited to, steel wool, aluminum foil or
any buildup of metallic particles should
be kept away from charger cavities.
Always unplug the charger from the
power supply when there is no battery
pack in the cavity. Unplug charger
before attempting to clean
• DO NOT attempt to charge the battery pack
with any chargers other than the ones in
this manual. The charger and battery pack are
specifically designed to work together.
• These chargers are not intended for
any uses other than charging DeWALT
rechargeable batteries. Any other uses
may result in risk of fire, electric shock or
electrocution.
7
English
• Do not expose charger to rain or snow.
• Pull by plug rather than cord when
disconnecting charger. This will reduce risk
of damage to electric plug and cord.
• Make sure that cord is located so that it
will not be stepped on, tripped over, or
otherwise subjected to damage or stress.
• Do not use an extension cord unless it
is absolutely necessary. Use of improper
extension cord could result in risk of fire,
electric shock, or electrocution.
• Do not place any object on top of charger
or place the charger on a soft surface that
might block the ventilation slots and result
in excessive internal heat. Place the charger
in a position away from any heat source. The
charger is ventilated through slots in the top and
the bottom of the housing.
• Do not operate charger with damaged cord
or plug—have them replaced immediately.
•Do not operate charger if it has received
a sharp blow, been dropped, or otherwise
damaged in any way. Take it to an authorised
service centre.
• Do not disassemble charger; take it to an
authorised service centre when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock, electrocution or
fire.
• In case of damaged power supply cord the
supply cord must be replaced immediately by
the manufacturer, its service agent or similar
qualified person to prevent any hazard.
• Disconnect the charger from the outlet
before attempting any cleaning. This will
reduce the risk of electric shock. Removing
the battery pack will not reduce this risk.
•NEVER attempt to connect two chargers
together.
• The charger is designed to operate on
standard 230V household electrical power.
Do not attempt to use it on any other
voltage. This does not apply to the vehicular
charger.
SAVE THESE INSTRUCTIONS
DeWALT chargers require no adjustment and are
designed to be as easy as possible to operate.
Charging Procedure (Fig. 2)
1.Plug the charger into an appropriate outlet
before inserting battery pack.
2.Insert the battery pack (h) into the charger.
The red (charging) light will blink continuously
indicating that the charging process has started.
3.The completion of charge will be indicated by
the red light remaining ON continuously. The
pack is fully charged and may be used at this
time or left in the charger.
NOTE: To ensure maximum performance and life
of lithium-ion batteries, charge the battery pack fully
before first use.
Charging Process
Refer to the table below for the charge status of the
battery pack.
Charge indicators: DCB105
charging
fully charged
hot/cold pack delay
replace battery pack
Charge indicators: DCB107, DCB112, DCB113, DCB115
charging
fully charged
hot/cold pack delay*
*DCB107, DCB112, DCB113, DCB115: The
red light will continue to blink, but a yellow
indicator light will be illuminated during this
operation. Once the battery has reached an
appropriate temperature, the yellow light will turn
off and the charger will resume the charging
procedure.
The compatible charger(s) will not charge a faulty
battery pack. The charger will indicate faulty battery
by refusing to light or by displaying problem pack or
charger blink pattern.
Chargers
NOTE: This could also mean a problem with a
charger.
The DCB105, DCB107, DCB112, DCB113 and
DCB115 chargers accept 10.8V, 14.4V and 18V
Li-Ion XR (DCB140, DCB141, DCB142, DCB143,
DCB144, DCB145, DCB180, DCB181, DCB182,
DCB183, DCB183B, DCB184, DCB184B and
DCB185) battery packs.)
If the charger indicates a problem, take the charger
and battery pack to be tested at an authorised
service centre.
8
English
HOT/COLD PACK DELAY
crush, drop or damage battery pack.
Do not use a battery pack or charger
that has received a sharp blow, been
dropped, run over or damaged in any
way (i.e., pierced with a nail, hit with a
hammer, stepped on). Electric shock
or electrocution may result. Damaged
battery packs should be returned to
service centre for recycling.
When the charger detects a battery that is too hot
or too cold, it automatically starts a Hot/Cold Pack
Delay, suspending charging until the battery has
reached an appropriate temperature. The charger
then automatically switches to the pack charging
mode. This feature ensures maximum battery life.
A cold battery pack will charge at about half the rate
of a warm battery pack. The battery pack will charge
at that slower rate throughout the entire charging
cycle and will not return to maximum charge rate
even if the battery warms.
LITHIUM-ION BATTERY PACKS ONLY
XR Li-Ion tools are designed with an Electronic
Protection System that will protect the battery
against overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic
Protection System engages. If this occurs, place
the lithium-ion battery on the charger until it is fully
charged.
Important Safety Instructions for All
Battery Packs
When ordering replacement battery packs, be sure
to include catalog number and voltage.
The battery pack is not fully charged out of the
carton. Before using the battery pack and charger,
read the safety instructions below. Then follow
charging procedures outlined.
READ ALL INSTRUCTIONS
• Do not charge or use battery in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Inserting
or removing the battery from the charger may
ignite the dust or fumes.
• Never force battery pack into charger. Do
not modify battery pack in any way to fit into
a non-compatible charger as battery pack
may rupture causing serious personal injury.
• Charge the battery packs only in DeWALT
chargers.
• DO NOT splash or immerse in water or other
liquids.
• Do not store or use the tool and battery
pack in locations where the temperature
may reach or exceed 40 ˚C (104 ˚F) (such as
outside sheds or metal buildings in summer).
WARNING: Never attempt to open the
battery pack for any reason. If battery
pack case is cracked or damaged,
do not insert into charger. Do not
CAUTION: When not in use, place
tool on its side on a stable surface
where it will not cause a tripping or
falling hazard. Some tools with large
battery packs will stand upright on the
battery pack but may be easily knocked
over.
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM-ION
(LI-ION)
• Do not incinerate the battery pack even if it
is severely damaged or is completely worn
out. The battery pack can explode in a fire.
Toxic fumes and materials are created when
lithium-ion battery packs are burned.
• If battery contents come into contact with
the skin, immediately wash area with mild
soap and water. If battery liquid gets into the
eye, rinse water over the open eye for
15 minutes or until irritation ceases. If medical
attention is needed, the battery electrolyte
is composed of a mixture of liquid organic
carbonates and lithium salts.
• Contents of opened battery cells may cause
respiratory irritation. Provide fresh air. If
symptoms persists, seek medical attention.
WARNING: Burn hazard. Battery liquid
may be flammable if exposed to spark
or flame.
Transportation
DeWALT batteries comply with all applicable
shipping regulations as prescribed by industry and
legal standards which include UN Recommendations
on the Transport of Dangerous Goods; International
Air Transport Association (IATA) Dangerous Goods
Regulations, International Maritime Dangerous
Goods (IMDG) Regulations, and the European
Agreement Concerning The International Carriage
of Dangerous Goods by Road (ADR). Lithium-ion
cells and batteries have been tested to section 38.3
of the UN Recommendations on the Transport of
Dangerous Goods Manual of Tests and Criteria.
In most instances, shipping a DeWALT battery pack
will be excepted from being classified as a fully
regulated Class 9 Hazardous Material. In general,
the two instances that require shipping Class 9 are:
9
English
1.Air shipping more than two DeWALT lithium-ion
battery packs when the package contains only
battery packs (no tools), and
Read instruction manual before use.
2.Any shipment containing a lithium-ion battery
with an energy rating greater than 100 watt
hours (Wh). All lithium-ion batteries have the
watt hour rating marked on the pack.
See Technical Data for charging time.
Regardless of whether a shipment is considered
excepted or fully regulated, it is the shipper's
responsibility to consult the latest regulations for
packaging, labeling/marking and documentation
requirements.
Transporting batteries can possibly cause fire if the
battery terminals inadvertently come in contact with
conductive materials. When transporting batteries,
make sure that the battery terminals are protected
and well insulated from materials that could contact
them and cause a short circuit.
The information provided in this section of the
manual is provided in good faith and believed to be
accurate at the time the document was created.
However, no warranty, expressed or implied, is
given. It is the buyer’s responsibility to ensure that its
activities comply with the applicable regulations.
Battery Pack
BATTERY TYPE
The DCD932 and DCD937 operate on 14.4 volt
battery packs.
Battery charging.
Battery charged.
Battery defective.
Hot/cold pack delay.
Do not probe with conductive objects.
Do not charge damaged battery packs.
Do not expose to water.
Have defective cords replaced
immediately.
Charge only between 4 ˚C and 40 ˚C.
The DCD990 and DCD995 operate on 18 volt
battery pack.
Only for indoor use.
The DCB140, DCB141, DCB142, DCB143,
DCB144, DCB145, DCB180, DCB181, DCB182,
DCB183, DCB183B, DCB184, DCB184B and
DCB185 battery packs may be used. Refer to
Technical Data for more information.
Discard the battery pack with due care
for the environment.
Storage Recommendations
1.The best storage place is one that is cool and
dry away from direct sunlight and excess heat
or cold. For optimum battery performance and
life, store battery packs at room temperature
when not in use.
Charge DeWALT battery packs only with
designated DeWALT chargers. Charging
battery packs other than the designated
DeWALT batteries with a DeWALT
charger may make them burst or lead to
other dangerous situations.
Do not incinerate the battery pack.
2.For long storage, it is recommended to store a
fully charged battery pack in a cool, dry place
out of the charger for optimal results.
Package Contents
NOTE: Battery packs should not be stored
completely depleted of charge. The battery pack will
need to be recharged before use.
1 Brushless cordless drill/driver
(DCD932, DCD990)
Labels on Charger and Battery Pack
In addition to the pictographs used in this manual,
the labels on the charger and the battery pack show
the following pictographs:
10
The package contains:
1 Brushless cordless hammerdrill
(DCD937, DCD995)
2 Li-Ion battery packs (M2)
2 Li-Ion battery packs (P2)
English
3 Li-Ion battery packs (M3)
3 Li-Ion battery packs (P3)
1 Kitbox
1 Charger
1 Side handle
1 Instruction manual
NOTE: Battery packs, chargers and kitboxes are
not included with N-models.
• Check for damage to the tool, parts or
accessories which may have occurred during
transport.
• Take the time to thoroughly read and
understand this manual prior to operation.
Description (Fig. 1)
WARNING: Never modify the power
tool or any part of it. Damage or
personal injury could result.
• This product is not intended for use by persons
(including children) suffering from diminished
physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are
supervised by a person responsible for their
safety. Children should never be left alone with
this product.
Electrical Safety
The electric motor has been designed for one
voltage only. Always check that the battery pack
voltage corresponds to the voltage on the rating
plate. Also make sure that the voltage of your
charger corresponds to that of your mains.
Your DeWALT charger is double insulated
in accordance with EN60335; therefore
no earth wire is required.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
DeWALT service organization.
b.Forward/reverse control button
Mains Plug Replacement
(U.K. & Ireland Only)
c.Worklight
If a new mains plug needs to be fitted:
d.Chuck
• Safely dispose of the old plug.
e.Torque adjustment collar
• Connect the brown lead to the live terminal in
the plug.
a.Trigger switch
f.
Gear shifter
g.Side handle
h.Battery pack
i.
Battery release button
j.Belt hook
k.Mounting screw
l.Magnetic bit holder
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 3 A.
Using an Extension Cable
These drills drivers/hammerdrills are designed
for professional drilling, percussion drilling and
screwdriving applications.
An extension cord should not be used unless
absolutely necessary. Use an approved extension
cable suitable for the power input of your charger
(see Technical Data). The minimum conductor size
is 1 mm2; the maximum length is 30 m.
DO NOT use under wet conditions or in presence of
flammable liquids or gases.
When using a cable reel, always unwind the cable
completely.
These drills/drivers/hammerdrills are professional
power tools.
ASSEMBLY AND ADJUSTMENTS
INTENDED USE
DO NOT let children come into contact with the
tool. Supervision is required when inexperienced
operators use this tool.
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up
can cause injury.
WARNING: Use only DeWALT battery
packs and chargers.
•Young children and the infirm. This appliance
is not intended for use by young children or
infirm persons without supervision.
11
English
Inserting and Removing the
Battery Pack from the Tool (Fig. 2)
NOTE: For best results, make sure your battery
pack is fully charged.
TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE
1.Align the battery pack (h) with the rails inside the
tool’s handle (Fig. 2).
2.Slide it into the handle until the battery pack is
firmly seated in the tool and ensure that it does
not disengage.
TO REMOVE THE BATTERY PACK FROM THE TOOL
1.Press the battery release button (i) and firmly
pull the battery pack out of the tool handle.
2.Insert battery pack into the charger as
described in the charger section of this manual.
FUEL GAUGE BATTERY PACKS (FIG. 2)
Some DeWALT battery packs include a fuel gauge
which consists of three green LED lights that
indicate the level of charge remaining in the battery
pack.
To actuate the fuel gauge, press and hold the fuel
gauge button (m). A combination of the three green
LED lights will illuminate designating the level of
charge left. When the level of charge in the battery
is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
NOTE: The fuel gauge is only an indication of the
charge left on the battery pack. It does not indicate
tool functionality and is subject to variation based
on product components, temperature and end-user
application.
Variable Speed Switch (Fig. 1)
To turn the tool on, squeeze the trigger switch (a).
To turn the tool off, release the trigger switch. Your
tool is equipped with a brake. The chuck will stop as
soon as the trigger switch is fully released.
NOTE: Continuous use in variable speed range is
not recommended. It may damage the switch and
should be avoided.
Side Handle (Fig. 1)
12
WARNING: To reduce the risk of
personal injury, ALWAYS operate
the tool with the side handle properly
installed. Failure to do so may result
in the side handle slipping during tool
operation and subsequent loss of
control. Hold tool with both hands to
maximize control.
The side handle (g) clamps to the front of the gear
case and may be rotated 360˚ to permit right- or
left-hand use. Side handle must be tightened
sufficiently to resist the twisting action of the tool if
the accessory binds or stalls. Be sure to grip the
side handle at the far end to control the tool
during a stall.
If model is not equipped with side handle, grip drill
with one hand on the handle and one hand on the
battery pack.
NOTE: Side handle comes equipped on all models.
Forward/Reverse Control Button
(Fig. 1)
A forward/reverse control button (b) determines the
direction of the tool and also serves as a lock off
button.
To select forward rotation, release the trigger switch
and depress the for­ward/re­verse control button on
the right side of the tool.
To select reverse, release the trigger switch and
depress the forward/reverse control button on the
left side of the tool.
The center position of the control button locks the
tool in the off position. When changing the position
of the control button, be sure the trigger is released.
NOTE: The first time the tool is run after changing
the direction of rotation, you may hear a click on
start up. This is normal and does not indicate a
problem.
Worklight (Fig. 1)
There is a worklight (c) located on the foot of the
tool. The worklight is activated when the trigger
switch is depressed. When the trigger switch is
released, the worklight will stay illuminated for up to
20 seconds.
NOTE: The worklight is for lighting the immediate
work surface and is not intended to be used as a
flashlight.
Torque Adjustment Collar/Electronic
Clutch (Fig. 3–5)
Your tool has an electronic adjustable torque
screwdriver mechanism for driving and removing
a wide array of fasteners. Circling the torque
adjustment collar (e) are numbers. These numbers
are used to set the clutch to deliver a torque range.
The higher the number on the collar, the higher the
torque and the larger the fastener which can be
driven. To select any of the numbers, rotate until the
desired number aligns with the arrow.
English
Three-Speed Gearing (Fig. 1, 3–5)
The three-speed feature of your tool allows you to
shift gears for greater versatility. To select speed 1
(highest torque setting), turn the tool off and permit it
to stop. Slide the gear shifter (f) all the way forward.
Speed 2 (middle torque and speed setting) is in the
middle position. Speed 3 (highest speed setting) is
to the rear.
NOTE: Do not change gears when the tool is
running. Always allow the drill to come to a complete
stop before changing gears. If you have trouble
changing gears, make sure that the gear shifter is
engaged in one of the three speed settings.
If the speed shifter becomes stuck or is difficult to
select the desired gear, pull the trigger switch (a) to
rotate the motor. Then select the gear.
Keyless Single Sleeve Chuck
(Fig. 6–8)
WARNING: Do not attempt to tighten
drill bits (or any other accessory) by
gripping the front part of the chuck
and turning the tool on. Damage to
the chuck and personal injury may
result. Always lock off trigger switch
and disconnect tool from power source
when changing acces­sories.
WARNING: Always ensure the bit is
secure before starting the tool. A loose
bit may eject from tool causing possible
personal injury.
Your tool features a keyless chuck with one rotating
sleeve for one-handed operation of the chuck. To
insert a drill bit or other accessory, follow these
steps.
1.Turn off tool and disconnect tool from power
source.
2.Grasp the black sleeve of the chuck (d) with
one hand and use the other hand to secure the
tool as shown in Figure 6. Rotate the sleeve
counterclockwise (as viewed from the front) far
enough to accept the desired accessory.
3.Insert the accessory about 19 mm (3/4") into
the chuck (Fig. 7). Tighten securely by rotating
the chuck sleeve clockwise with one hand while
holding the tool with the other hand (Fig. 8).
Continue to rotate the chuck sleeve until several
ratchet clicks are heard to ensure full gripping
power.
To release the accessory, repeat Steps 1 and 2
above.
Be sure to tighten chuck with one hand on the
chuck sleeve and one hand holding the tool for
maximum tightness.
Belt Hook and Magnetic Bit Holder
(Fig. 1)
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories.
WARNING: To reduce the risk of
serious personal injury, DO NOT
suspend tool overhead or suspend
objects from the belt hook. ONLY hang
tool’s belt hook from a work belt.
WARNING: To reduce the risk of
serious personal injury, ensure the
screw holding the belt hook is secure.
IMPORTANT: When attaching or replacing the belt
hook or magnetic bit holder, use only the screw
(k) that is provided. Be sure to securely tighten the
screw.
The belt hook (j) and magnetic bit holder (l) can be
be attached to either side of the tool using only the
screw (k) provided, to accommodate left- or righthanded users. If the hook or magnetic bit holder is
not desired at all, it can be removed from the tool.
To move belt hook or magnetic bit holder, remove
the screw (k) that holds it in place then reassemble
on the opposite side. Be sure to securely tighten the
screw.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories. An accidental start-up
can cause injury.
Proper Hand Position (Fig. 9)
WARNING: To reduce the risk of
serious personal injury, ALWAYS
use proper hand position as shown
in figure 9.
13
English
Proper hand position requires one hand on the
main handle (n), with the other hand on the side
handle (g).
Drill Operation (Fig. 4)
speed 2 or 3. This ensures effective control over
the fastener allowing the screw to be seated
correctly and set to specification. Speed 1 will
provide the same clutching torque as speeds
2 and 3. However, for optimum performance
of the electronic clutch, speeds 2 and 3 are
preferred.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
WARNING: To reduce the risk of
personal injury, ALWAYS ensure
workpiece is anchored or clamped
firmly. If drilling thin material, use a wood
“back-up” block to prevent damage to
the material.
NOTE: Use the lowest torque setting (1) first
and increase the number through to the highest
setting (11) to seat the fastener at the desired
depth. The lower the number, the lower the
torque output.
2.Reset the torque adjustment collar (e) to the
appropriate number setting for the torque
desired. Make a few practice runs in scrap or
unseen areas to determine the proper position
of the torque adjustment collar.
NOTE: The torque adjustment collar may be set to
any number at any time.
Hammerdrill Operation (Fig. 5)
1.Select the desired speed/torque range using
the gear shifter to match the speed and torque
to the planned operation. Set the torque
adjustment collar (e) to the drill symbol.
1.Select the desired speed/torque range using
the gear shifter to match the speed and torque
to the planned operation. Set the torque
adjustment collar (e) to the hammer symbol.
2.For WOOD, use twist bits, spade bits, power
auger bits or hole saws. For METAL, use highspeed steel twist drill bits or hole saws. Use
a cutting lubricant when drilling metals. The
exceptions are cast iron and brass which should
be drilled dry.
2.Select the high speed 3 setting by sliding the
gear shifter (f) back (away form the chuck).
3.Always apply pressure in a straight line with the
bit. Use enough pressure to keep the drill bit
biting, but do not push hard enough to stall the
motor or deflect the bit.
4.Hold tool firmly with both hands to control the
twisting action of the drill.
5.IF DRILL STALLS, it is usually because it
is being overloaded. RELEASE TRIGGER
IMMEDIATELY, remove drill bit from work,
and determine cause of stalling. DO NOT
CLICK TRIGGER OFF AND ON IN AN
ATTEMPT TO START A STALLED DRILL –
THIS CAN DAMAGE THE DRILL.
6.Keep the motor running when pulling the bit
back out of a drilled hole. This will help prevent
jamming.
Screwdriver Operation (Fig. 3)
1.Select the desired speed/torque range using
the three-speed gear shifter (f) on the top of
the tool. If using the torque adjustment collar
(e), initially set the three-speed gear shifter to
14
3.When drilling, use just enough force on the
hammer to keep it from bouncing excessively.
Prolonged and too much force on the hammer
will cause slower drilling speeds and potential
overheating.
4.Drill straight, keeping the bit at a right angle to
the work. Do not exert side pressure on the bit
when drilling as this will cause clogging of the
bit flutes and a slower drilling speed.
5.When drilling deep holes, if the hammer speed
starts to drop off, pull the bit partially out of
the hole with the tool still running to help clear
debris from the hole.
6.For masonry, use carbide-tipped bits or
masonry bits. A smooth, even flow of dust
indicates the proper drilling rate.
MAINTENANCE
Your DeWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
English
removing/installing attachments or
accessories. An accidental start-up
can cause injury.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING: Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect
the charger from the AC outlet before
cleaning. Dirt and grease may be
removed from the exterior of the charger
using a cloth or soft non-metallic brush.
Do not use water or any cleaning
solutions.
Optional Accessories
WARNING: Since accessories, other
than those offered by DeWALT, have
not been tested with this product, use
of such accessories with this tool could
be hazardous. To reduce the risk of
injury, only DeWALT recommended
accessories should be used with this
product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. This product must
not be disposed of with normal
household waste.
Should you find one day that your DeWALT product
needs replacement, or if it is of no further use to
you, do not dispose of it with household waste.
Make this product available for separate collection.
S
eparate collection of used products
and packaging allows materials to be
recycled and used again. Re-use of
recycled materials helps prevent
environmental pollution and reduces
the demand for raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at
municipal waste sites or by the retailer when you
purchase a new product.
DeWALT provides a facility for the collection and
recycling of DeWALT products once they have
reached the end of their working life. To take
advantage of this service please return your product
to any authorised repair agent who will collect them
on our behalf.
You can check the location of your nearest
authorised repair agent by contacting your local
DeWALT office at the address indicated in this
manual. Alternatively, a list of authorised DeWALT
repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when
it fails to produce sufficient power on jobs which
were easily done before. At the end of its technical
life, discard it with due care for our environment:
• Run the battery pack down completely, then
remove it from the tool.
• Li-Ion cells are recyclable. Take them to your
dealer or a local recycling station. The collected
battery packs will be recycled or disposed of
properly.
15
16
17
Belgique et
Luxembourg België
en Luxemburg
DeWALT - Belgium BVBA
Egide Walschaertsstraat 16
2800 Mechelen
Tel: NL 32 15 47 37 63
Tel: FR 32 15 47 37 64
Fax: 32 15 47 37 99
www.dewalt.be
[email protected]
Danmark
DeWALT
Roskildevej 22
2620 Albertslund
Tel: 70 20 15 10
Fax: 70 22 49 10
www.dewalt.dk
[email protected]
Deutschland
DeWALT
Richard Klinger Str. 11
65510 Idstein
Tel:06126-21-1
Fax:06126-21-2770
www.dewalt.de
[email protected]
Ελλάς
DeWALT (Ελλάς) Α.Ε.
Τηλ: 00302108981616
EΔΡΑ-ΓΡΑΦΕΙΑ : Στράβωνος 7
Φαξ: 00302108983570
& Λ. Βουλιαγμένης, Γλυφάδα 166 74, Αθήνα
SERVICE : Ημερος Τόπος 2 (Χάνι Αδάμ) –
193 00 Ασπρόπυργος
www.dewalt.gr
[email protected]
España
DeWALT Ibérica, S.C.A.
Parc de Negocios “Mas Blau”
Edificio Muntadas, c/Bergadá, 1, Of. A6
08820 El Prat de Llobregat (Barcelona)
Tel: 934 797 400
Fax: 934 797 419
www.dewalt.es
[email protected]
France
DeWALT
5, allée des Hêtres
BP 30084, 69579 Limonest Cedex
Tel: 04 72 20 39 20
Fax: 04 72 20 39 00
www.dewalt.fr
[email protected]
Schweiz
Suisse
Svizzera
DeWALT
In der Luberzen 42
8902 Urdorf
Tel: 044 - 755 60 70
Fax: 044 - 730 70 67
www.dewalt.ch
[email protected]
Ireland
DeWALT
Calpe House Rock Hill
Black Rock, Co. Dublin
Tel:00353-2781800
Fax:00353-2781811
www.dewalt.ie
Italia
DeWALT
via Energypark
20871 Vimercate (MB), IT
Tel: 800-014353
39 039 9590200
Fax: 39 039 9590313
www.dewalt.it
Nederlands
DeWALT Netherlands BV
Tel: 31 164 283 063
Holtum Noordweg 35
Fax: 31 164 283 200
6121 RE BORN, Postbus 83, 6120 AB BORN
www.dewalt.nl
Norge
DeWALT
Postboks 4613, Nydalen
0405 Oslo
Tel: 45 25 13 00
Fax: 45 25 08 00
www.dewalt.no
[email protected]
Österreich
DeWALT
Werkzeug Vertriebsges m.b.H
Oberlaaerstrasse 248, A-1230 Wien
Tel: 01 - 66116 - 0
Fax: 01 - 66116 - 614
www.dewalt.at
[email protected]
Portugal
DeWALT Limited, SARL
Tel: 214 66 75 00
Centro de Escritórios de Sintra Avenida
Fax: 214 66 75 80
Almirante Gago Coutinho, 132/134, Edifício 14
2710-418 Sintra
www.dewalt.pt
[email protected]
Suomi
DeWALT
PL 47
00521 Helsinki
Puh: 010 400 4333
Faksi:0800 411 340
www.dewalt.fi
[email protected]
Sverige
DeWALT
Box 94
431 22 Mölndal
Tel: 031 68 61 60
Fax: 031 68 60 08
www.dewalt.se
[email protected]
Türkiye
KALE Hırdavat ve Makina A.Ş.
Defterdar Mah. Savaklar Cad. No:15
Edirnekapı / Eyüp / İSTANBUL 34050
TÜRKİYE
Tel: 0212 533 52 55
Faks: 0212 533 10 05
www.dewalt.com.tr
United
Kingdom
DeWALT, 210 Bath Road;
Slough, Berks SL1 3YD
Tel: 01753-567055
Fax: 01753-572112
www.dewalt.co.uk
[email protected]
Australia
DeWALT
82 Taryn Drive, Epping
VIC 3076 Australia
Tel: Aust 1800 338 002
Tel: NZ 0800 339 258
www.dewalt.com.au
www.dewalt.co.nz
Middle East Africa
DeWALT
P.O. Box - 17164,
Jebel Ali Free Zone (South), Dubai, UAE
Tel: 971 4 812 7400
Fax: 971 4 2822765
www.dewalt.ae
[email protected]
N44944908/15