FME821 | Stanley FME821 SMALL ANGLE GRINDER instruction manual

www.stanley.eu
FME821
FME822
A
B
C
D
13
16
15
10
5
E
2
F
(Original instructions)
Intended use
Your Stanley Fat Max angle grinder FME821, FME822 has
been designed for grinding and cutting metal and masonry
using the appropriate type of cutting or grinding disc. When
fitted with the appropriate guard, this tool is intended for
professional and private, non professional users.
Safety instructions
General power tool safety warnings
@
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions listed below may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
ENGLISH
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in
serious personal injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
3
ENGLISH
(Original instructions)
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5.Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional power tool safety warnings
@
Warning! Additional safety warnings for grind-
u
ing, sanding, polishing or abrasive cutting-off
operations
This power tool is intended to function as a grinder,
sander, polisher or cut-off tool. Read all safety warnings, instructions, illustrations and specifications
provided with this power tool. Failure to follow all
instructions listed below may result in electric shock, fire
and/or serious injury.
u Operations for which the power tool was not designed
may create a hazard and cause personal injury.
u Do not use accessories which are not specifically
designed and recommended by the tool manufacturer.
Just because the accessory can be attached to your
power tool, it does not assure safe operation.
u The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated speed
can break and fly apart.
u The outside diameter and the thickness of your accessory must be within the capacity rating of your power
tool. Incorrectly sized accessories cannot be adequately
guarded or controlled.
u Threaded mounting of accessories must match the
grinder spindle thread. For accessories mounted by
4
flanges, the arbour hole of the accessory must fit the
locating diameter of the flange. Accessories that do not
match the mounting hardware of the power tool will run
out of balance, vibrate excessively and may cause loss of
control.
u Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for cracks, tear or
excess wear, for loose or cracked wires. If power tool
or accessory is dropped, inspect for damage or install
an undamaged accessory. After inspecting and installing an accessory and run the power tool at maximum
no-load speed for one minute. Damaged accessories
will normally break apart during this test time.
u Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of
stopping small abrasive or workpiece fragments.
The eye protection must be capable of stopping flying
debris generated by various operations. The dust mask or
respirator must be capable of filtering particles generated
by your operation. Prolonged exposure to high intensity
noise may cause hearing loss.
u Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal
protective equipment. Fragments of workpiece or of a
broken accessory may fly away and cause injury beyond
immediate area of operation.
u Hold power tool by insulated gripping surfaces only,
when performing an operation where the cutting
accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and shock the
operator.
u Position the cord clear of the spinning accessory. If
you lose control, the cord may be cut or snagged and your
hand or arm may be pulled into the spinning accessory.
u Never lay the power tool down until the accessory
has come to a complete stop. The spinning accessory
may grab the surface and pull the power tool out of your
control.
u Do not run the power tool while carrying it at your
side. Accidental contact with the spinning accessory could
snag your clothing, pulling the accessory into your body.
u Regularly clean the power tool's air vents. The motor's
fan will draw the dust inside the housing and excessive
accumulation of powdered metal may cause electrical
hazards.
u Do not operate the power tool near flammable materials. Sparks could ignite these materials.
(Original instructions)
u
Do not use accessories that require liquid coolants.
Using water or other liquid coolants may result in electrocution or shock.
Note: The above warning does not apply for power tools
specifically designed for use with a liquid system.
Kickback and related warnings
Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory. Pinching or snagging causes rapid stalling of the rotating accessory
which in turn causes the uncontrolled power tool to be forced
in the direction opposite of the accessory's rotation at the point
of the binding.
For example, if an abrasive wheel is snagged or pinched by
the workpiece, the edge of the wheel that is entering into the
pinch point can dig into the surface of the material causing
the wheel to climb out or kick out. The wheel may either jump
toward or away from the operator, depending on direction of
the wheel's movement at the point of pinching.
Abrasive wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below.
u Maintain a firm grip on the power tool and position
your body and arm to allow you to resist kickback
forces. Always use auxiliary handle, if provided, for
maximum control over kickback or torque reaction
during start-up. The operator can control torque reactions or kickback forces, if proper precautions are taken.
u Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
u Do not position your body in the area where power
tool will move if kickback occurs. Kickback will propel
the tool in direction opposite to the wheel's movement at
the point of snagging.
u Use special care when working corners, sharp edges
etc. Avoid bouncing and snagging the accessory.
Corners, sharp edges or bouncing have a tendency to
snag the rotating accessory and cause loss of control or
kickback.
u Do not attach a saw chain woodcarving blade or
toothed saw blade. Such blades create frequent kickback
and loss of control.
Safety warnings specific for grinding and abrasive
cutting-off operations
u Use only wheel types that are recommended for your
power tool and the specific guard designed for the
selected wheel. Wheels for which the power tool was not
designed cannot be adequately guarded and are unsafe.
ENGLISH
The grinding surface of centre depressed wheels
must be mounted below the plane of the guard lip. An
improperly mounted wheel that projects through the plane
of the guard lip cannot be adequately protected.
u The guard must be securely attached to the power
tool and positioned for maximum safety, so the least
amount of wheel is exposed towards the operator.
The guard helps to protect operator from broken wheel
fragments, accidental contact with wheel and sparks that
could ignite clothing.
u Wheels must be used only for recommended applications. For example: do not grind with the side of
cut-off wheel. Abrasive cut-off wheels are intended for
peripheral grinding, side forces applied to these wheels
may cause them to shatter.
u Always use undamaged wheel flanges that are of
correct size and shape for your selected wheel. Proper
wheel flanges support the wheel thus reducing the possibility of wheel breakage. Flanges for cut-off wheels may
be different from grinding wheel flanges.
u Do not use worn down wheels from larger power
tools. Wheel intended for larger power tool is not suitable
for the higher speed of a smaller tool and may burst.
u
Additional safety warnings specific for abrasive
cutting-off operations
u Do not "jam" the cut-off wheel or apply excessive
pressure. Do not attempt to make an excessive depth
of cut. Over stressing the wheel increases the loading
and susceptibility to twisting or binding of the wheel in the
cut and the possibility of kickback or wheel breakage.
u Do not position your body in line with and behind the
rotating wheel. When the wheel, at the point of operation,
is moving away from your body, the possible kickback may
propel the spinning wheel and the power tool directly at
you.
u When wheel is binding or when interrupting a cut for
any reason, switch off the power tool and hold the
power tool motionless until the wheel comes to a
complete stop. Never attempt to remove the cut-off
wheel from the cut while the wheel is in motion
otherwise kickback may occur. Investigate and take
corrective action to eliminate the cause of wheel binding.
u Do not restart the cutting operation in the workpiece.
Let the wheel reach full speed and carefully re-enter
the cut. The wheel may bind, walk up or kickback if the
power tool is restarted in the workpiece.
u Support panels or any oversized workpiece to minimize the risk of wheel pinching and kickback. Large
workpieces tend to sag under their own weight. Supports
must be placed under the workpiece near the line of cut
and near the edge of the workpiece on both sides of the
wheel.
5
ENGLISH
u
(Original instructions)
Use extra caution when making a "pocket cut" into ex-
isting walls or other blind areas. The protruding wheel
may cut gas or water pipes, electrical wiring or objects that
can cause kickback.
Safety warnings specific for sanding operations
u Do not use excessively oversized sanding disc paper.
Follow manufacturers recommendations, when selecting sanding paper. Larger sanding paper extending
beyond the sanding pad presents a laceration hazard and
may cause snagging, tearing of the disc or kickback.
Safety warnings specific for polishing operations
u Do not allow any loose portion of the polishing bonnet
or its attachment strings to spin freely. Tuck away or
trim any loose attachment strings. Loose and spinning
attachment strings can entangle your fingers or snag on
the workpiece.
Safety of others
u This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a person responsible for their
safety.
u Children should be supervised to ensure that they do not
play with the appliance.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving
parts.
u Injuries caused when changing any parts, blades or
accessories.
u Injuries caused by prolonged use of a tool. When
using any tool for prolonged periods ensure you take
regular breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured in
accordance with a standard test method provided by EN60745
6
and may be used for comparing one tool with another. The
declared vibration emission value may also be used in a
preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following pictograms as well as the date code are shown
on the tool:
:
Warning! To reduce the risk of injury, the user must
O
read the instruction manual.
Wear safety glasses or goggles when operating this
N
tool.
Wear ear protection when operating this tool.
Electrical safety
#
u
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Stanley Fat Max Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Side handle
3. Spindle lock
4. Grinding guard
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting and removing the guard (fig. A)
The tool is supplied with a guard intended for grinding
purposes and cutting purposes. Ensure you use the correct
(Original instructions)
guard specific for the intended operation. If the unit is intended
to perform cutting off operations, a guard (17, Fig F) specific
for this operation must be fitted .
Fitting
u Place the tool on a table, with the spindle (5) facing up.
u Release the clamping lock (7) and hold the guard (4) over
the tool as shown.
u Align the lugs (8) with the notches (9).
u Press the guard down and rotate it counterclockwise to
the required position.
u Fasten the clamping lock (7) to secure the guard to the
tool.
u If required, tighten the screw (6) to increase the clamping
force.
Removing
u Release the clamping lock (7).
u Rotate the guard clockwise to align the lugs (8) with the
notches (9).
u Remove the guard from the tool.
Warning! Never use the tool without the guard.
Fitting the side handle
u Screw the side handle (2) into one of the mounting holes
in the tool.
Warning! Always use the side handle.
Fitting and removing grinding or cutting discs
(fig. B - D)
Always use the correct type of disc for your application.
Always use discs with the correct diameter and bore size (see
technical data).
Fitting
u Fit the guard as described above.
u Place the inner flange (10) onto the spindle (5) as shown
(fig. B). Make sure that the flange is correctly located on
the flat sides of the spindle.
u Place the disc (11) onto the spindle (5) as shown (fig. B).
If the disc has a raised centre (12), make sure that the
raised centre faces the inner flange.
u Make sure that the disc locates correctly on the inner
flange.
u Place the outer flange (13) onto the spindle. When fitting
a grinding disc, the raised centre on the outer flange must
face towards the disc (A in fig. C). When fitting a cutting
disc, the raised centre on the outer flange must face away
from the disc (B in fig. C).
u Keep the spindle lock (3) depressed and tighten the outer
flange using the two-pin spanner (14) (fig. D).
ENGLISH
Removing
u Keep the spindle lock (3) depressed and loosen the outer
flange (13) using the two-pin spanner (14) (fig. D).
u Remove the outer flange (13) and the disc (11).
Fitting and removing sanding discs (fig. D & E)
For sanding, a backing pad is required. The backing pad is
available from your Stanley Fat Max dealer as an accessory.
Fitting
u Place the inner flange (10) onto the spindle (5) as shown
(fig. E). Make sure that the flange is correctly located on
the flat sides of the spindle.
u Place the backing pad (15) onto the spindle.
u Place the sanding disc (16) onto the backing pad.
u Place the outer flange (13) onto the spindle with the raised
centre facing away from the disc.
u Keep the spindle lock (3) depressed and tighten the outer
flange using the two-pin spanner (14) (fig. D). Make sure
that the outer flange is fitted correctly and that the disc is
clamped tightly.
Removing
u Keep the spindle lock (3) depressed and loosen the outer
flange (13) using the two-pin spanner (14) (fig. D).
u Remove the outer flange (13), the sanding disc (16) and
the backing pad (15).
Use
Warning! Let the tool work at its own pace. Do not overload.
u Carefully guide the cable in order to avoid accidentally
cutting it.
u Be prepared for a stream of sparks when the grinding or
cutting disc touches the workpiece.
u Always position the tool in such a way that the guard
provides optimum protection from the grinding or cutting
disc.
Switching on and off
u To switch on, slide the on/off switch (1) forward then press
it in. Note that the tool will continue running when you
release the switch.
u To switch off, press the rear part of the on/off switch.
Warning! Do not switch the tool off while under load.
Soft Start Feature
The soft start feature allows a slow speed build-up to avoid
an initial jerk when starting. This feature is particularly useful
when working in confined spaces.
7
ENGLISH
(Original instructions)
No-Volt
The No-volt function stops the grinder restarting without the
switch being cycled if there is a break in the power supply.
Hints for optimum use
u Firmly hold the tool with one hand around the side handle
and the other hand around the main handle.
u When grinding, always maintain an angle of approx. 15°
between the disc and the workpiece surface.
Maintenance
Technical data
FME821
Power input
W
850
850
Rated speed
min-1
12,000
12,000
Disc diameter
mm
115
125
Disc bore
mm
22
22
grinding discs
mm
6
6
cutting discs
mm
3.5
3.5
M14
M14
2.1
2.1
Warning! Before performing any maintenance on corded/
cordless power tools:
u Switch off and unplug the appliance/tool.
u Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
u Or run the battery down completely if it is integral and then
switch off.
u Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
u Regularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
u Regularly open the chuck and tap it to remove any dust
from the interior (when fitted).
Weight
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions.
8
230
VAC
Your Stanley Fat Max corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
If a new mains plug needs to be fitted:
u Safely dispose of the old plug.
u Connect the brown lead to the live terminal in the new
plug.
u Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
(Type 1)
230
Input voltage
Max disc thickness
Mains plug replacement (U.K. & Ireland only)
FME822
(Type 1)
Spindle size
kg
LpA (sound pressure) 94.5 dB(A), Uncertainty (K) 3 dB(A)
LWA (sound power) 105.5 dB(A), Uncertainty (K) 3 dB(A)
Vibration total values (triax vector sum) according to EN60745:
Surface grinding (ah,SG) 9.9 m/s2, uncertainty (K) 1.5 m/s2
Cutting-off (ah) 9.1 m/s2, uncertainty (K) 1.5 m/s2
Polishing (ah,P) 5.0 m/s2, uncertainty (K) 1.5 m/s2
Disc sanding (ah,DS) 3.3 m/s2, uncertainty (K) 1.5 m/s2
(Original instructions)
EC declaration of conformity
%
MACHINERY DIRECTIVE
FME821 / FME822 angle Grinder
Stanley Europe declares that these products described under
"technical data" are in compliance with:
2006/42/EC, EN60745-1:2009 +A11:2010;
EN60745-2-3:2011 +A2:2013 +A11:2014 +A12:2014
These products also comply with Directive 2014/108/EC (until
19.04.2016), 2014/30/EU (from 20.04.2016) and 2011/65/EU.
For more information, please contact Stanley Europe at the
following address or refer to the back of the manual.
.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of Stanley Europe.
ENGLISH
Guarantee
Stanley Fat Max is confident of the quality of its products and
offers consumers a 12 month guarantee* from the date of
purchase . This guarantee is in addition to and in no way
prejudices your statutory rights. The guarantee is valid within
the territories of the Member States of the European Union
and the European Free Trade Area.
To claim on the guarantee, the claim must be in accordance
with Stanley Fat Max Terms and conditions and you will need
to submit proof of purchase to the seller or an authorised
repair agent.
Terms and conditions of the Stanley Fat Max 1 year guarantee
and the location of your nearest authorised repair agent
can be obtained on the Internet at www.2helpU.com, or by
contacting your local Stanley Fat Max office at the address
indicated in this manual.
Please visit our website www.stanleytools.co.uk to register
your new Stanley Fat Max product and receive updates on
new products and special offers.
Ray Laverick
Director of Engineering
Stanley Europe, Egide Walschaertsstraat14-18,
2800 Mechelen, Belgium
25/08/2015
9
10
11
United Kingdom
Stanley Fat Max
210 Bath Road
Slough, Berkshire SL1 3YD
90629790 REV-0
Tel. 01753 511234
Fax 01753 572112
www.stanleytools.co.uk
11/2015
Download PDF

advertising