HBS-850

使用手冊

Bluetooth

®

立體聲耳機

Rev 1.0 TW

繁體中文

English

HBS-850

使用手冊

Bluetooth

®

立體聲耳機

保留一切權利。LG Electronics Inc., 2015

備註：為了讓 HBS-850 發揮最佳效能，並避免損壞或發生不當使用的情況，在使用 HBS-850

之前，請先仔細閱讀本手冊中的所有資訊。

任何因印刷錯誤或資訊不正確而須對本手冊進行的修改或變更，應由 LG Electronics Inc. 進行。

本手冊的所有資訊若有變更，將不另行通知。

繁體中文

簡介

LG TONE Active TM (HBS-850) 為使用 Bluetooth ® 技術的輕量型無線耳機。

本產品可搭配支援 A2DP 或免持藍牙操作模式的裝置，作為音訊配件使用。

包裝盒內容

2

額外的耳塞套

(1 組 - 小型)

HBS-850

(已安裝中型耳塞套和

穩定件)

額外的穩定件

(1 組 - 小型)

*USB 充電連接線

*實際產品設計可能與本手冊所顯示的圖片不同。

使用手冊

耳機

[音量調高]

按鈕/上一首

歌曲

[音量調低]

按鈕/下一首歌曲

耳塞 (右)

零件說明

穩定件

充電連接埠

LED 指示燈

麥克風

[電源]

(PWR)

按鈕

[多功能按鈕]

(MFB) 按鈕

耳塞 (左)

3

4

零件說明

更換穩定件

- 隨附一組額外的穩定件。 您可更換穩定件尺寸，以選擇適合您脖寬、配戴舒適的穩定件。

1

取下穩定件

2 1

安裝穩定件

3 4 2

3

開機/關機

- 開機：按住 [電源] (PWR) 按鈕 2 秒鐘。

- 關機：按住 [電源] (PWR) 按鈕 3 秒鐘。

充電中

- 連接充電器時，不論耳機為開機或關機狀態，耳機電源

都會關閉。

- 充電時，LED 指示燈會持續亮起紅燈。 充電達 80% 以上

時，指示燈會顯示紫色燈。

- 裝置充飽電時，LED 指示燈會持續亮起藍燈。

電量不足

- 每 2 分鐘出現一次電量不足提示。

- 若電池未充電，耳機電源則會關閉。

如何使用

電池狀態提示

- 按住 [音量調低] 按鈕 3 秒，即可檢查耳機的電池狀態。

電池狀態

語音提示

LED 指示燈

高

電量充足

閃爍

藍色燈

中

電量中等

閃爍

紫色燈

低

電量不足

閃爍

紅色燈

注意：配對時，某些行動裝置可能會在螢幕頂端顯示耳機

的電池電量。

收線式耳塞

- 拉動耳塞即可將耳塞線拉長至所需長度。

- 若要縮回耳塞，請稍微將耳塞線向外拉，耳塞即會自動

縮回定位。

- 如果耳機沒有縮回，請將耳塞整個向外拉來縮回耳塞。

5

6

如何使用

配對

- 若要使用耳機，您必須先將耳機與行動裝置配對。 裝置配

對後，耳機將會自動重新連線。

1) 簡單配對

1. 按住 [電源] (PWR) 按鈕 2 秒鐘以開啟耳機。

2. 若是首次配對裝置，或者耳機偵測不到先前配對的

裝置，耳機會進入 [配對] 模式。 LED 指示燈會持續

亮起藍燈。

3. 在您想要配對的裝置上找出 [藍牙] 功能表，然後搜

尋或新增裝置。

4 . 從裝置清單中選擇 [LG HBS850]。

5. 如果系統要求 Pass/PIN 碼，請輸入 0000 (4 個零)。

6 . 裝置配對後，您將會聽到「Your headset paired.」(您的

耳機已配對)。

注意：如果 3 分鐘內沒有進行配對，耳機電源將會自

動關閉。

2) 手動配對 (與其他手機配對或重新配對)

1. 在電源關閉時，同時按住 [多功能按鈕] (MFB) 和 [電

源] (PWR) 按鈕 2 秒鐘即可進入 [手動配對] 模式。

2. 當耳機進入 [配對] 模式，LED 指示燈會顯示恆亮的藍

燈。 重複「簡單配對」步驟 3 到 6。

進階多點連接功能

耳機能同時連線到兩個裝置。 這能讓您在兩支連線的手機

上，自由地在通話之間使用來電等候。

與兩個裝置配對

- 首先，將耳機與要作為次要裝置使用，且已啟用藍牙功能

的行動裝置配對 (請參閱「配對指示」)。

- 配對後，關閉耳機電源。

- 在電源關閉時，同時按住 [多功能按鈕] (MFB) 和 [電源]

(PWR) 按鈕 2 秒鐘。 此動作將會啟動 [手動配對] 模式。

- 將耳機與另一個已啟用藍牙功能的行動裝置進行配對並連

線。 (這將是您的主要裝置)。

- 主要行動裝置與耳機配對並連線後，將耳機重新連線到一

開始配對的行動裝置。

注意：耳機同時連線到兩個行動裝置時 (多點連接)，是在主

要行動裝置上使用耳機通話功能。

注意：若耳機無法透過「簡單配對」連線到主要手機，則

會進入配對模式。

通話功能

- [語音撥號] 與 [最後撥出號碼重撥] 功能是在主要手機 (或

是最後撥出電話的行動裝置) 上使用。

來電等候

- 通話時，按住 [多功能按鈕] (MFB) 按鈕 1 秒鐘即可接

聽來電。

- 若要在 2 個進行中通話之間切換，請按住 [多功能按鈕]

(MFB) 按鈕 1 秒鐘。

- 若要結束兩邊通話，請短按 [多功能按鈕] (MFB) 按鈕。

- 如果兩個配對的行動裝置同時接到來電，根據預設，耳機將

選擇主要手機。

如何使用

自動重新連線

- 耳機電源開啟時，若耳機與主要行動裝置位於連線範圍內，

則會自動重新連線。

- 次要行動裝置則需手動連線。 從 [藍牙] 功能表的裝置清單中

選擇 [LG HBS850]，然後進行連線。

不在涵蓋範圍內

- 配對的裝置之間若距離 33 英呎 (10 公尺) 以上，耳機和配

對行動裝置將會中斷連線，並且耳機會以震動提示您。

注意：若要關閉裝置震動功能，請按住 [音量調高] 按

鈕 3 秒鐘。

- 若耳機與配對行動裝置在回到要求範圍內時沒有自動重

新連線，請短按耳機上的 [多功能按鈕] (MFB) 按鈕來手

動重新連線。

- 進行多重連線和串流時，若非使用中的配對裝置超出範

圍，則會中斷連線。 耳機將提示您一次，但不會嘗試

重新連線。

7

8

如何使用

通話

接聽來電

- 接到來電時，耳機會響鈴並震動。

- 短按 [音量調低] 按鈕即可停止震動。

注意：震動功能停用後，耳機將不會震動。

- 短按 [多功能按鈕] (MFB) 按鈕即可接聽來電。

轉接電話

- 您可以按耳機上的 [音量調高] 按鈕 2 秒鐘，將電話手動

轉接到耳機，或將耳機的電話轉接到裝置 (行動裝置必須

與耳機配對)。

語音撥號

- 按住 [多功能按鈕] (MFB) 按鈕 1 秒鐘即可啟動 [語音

命令]。

注意：如果您的行動裝置不支援語音撥號，此動作可能會

啟動 [最後撥出號碼重撥]。

最後撥出號碼重撥

- 按住 [多功能按鈕] (MFB) 按鈕 2 秒鐘即可啟動 [最後撥出

號碼重撥]。 耳機將會撥打最後撥出的號嗎。

結束通話

- 短按 [多功能按鈕] (MFB) 按鈕。

來電等候

- 按下 [多功能按鈕] (MFB) 按鈕 1 秒鐘，即可接聽第二通來

電但不掛斷第一通電話。 按住 [多功能按鈕] (MFB) 按鈕 1

秒鐘即可回到第一通電話。

- 短按 [多功能按鈕] (MFB) 按鈕即可結束兩邊通話。

拒接來電

- 行動裝置鈴響時按下 [多功能按鈕] (MFB) 按鈕 2 秒鐘，即

可啟動 [拒接來電] 功能。

注意：這些功能可能不適用於所有行動裝置。 如需使用這

些功能的詳細資訊，請參閱行動裝置的使用手冊。

麥克風靜音

- 同時按住 [音量調高] 和 [音量調低] 按鈕 1 秒，即可在交談

期間將麥克風靜音/解除靜音。

音量控制

- 按下 [音量] 按鈕即可調整喇叭音量。

小心：長時間以高音量聆聽音樂，可能會造成聽力受損或

喪失。 為避免此情況，當您使用六級以上的音量時，耳機

會發出警告嗶聲。

震動控制

- 若要啟動或停用裝置震動功能，請按住 [音量調高] 按鈕 3

秒鐘。 您會在啟動或停用震動時，聽到「Vibrate on」(震

動開啟) 或「Vibrate off」(震動關閉)。

- 震動功能停用時，耳機在收到來電或超出配對的行動裝置

的連線範圍內時將不會震動。

- 裝置電源開啟時，震動功能將自動重新啟動。

如何使用

音訊串流

播放

- 短按 [多功能按鈕] (MFB) 按鈕。

暫停

- 播放音樂時短按 [多功能按鈕] (MFB) 按鈕。

下一首歌曲

- 按住 [音量調低] 按鈕 1 秒鐘。

上一首歌曲

- 按住 [音量調高] 按鈕 1 秒鐘。

等化器

- 播放音樂時按住 [多功能按鈕] (MFB) 按鈕 2 秒鐘，即可在

[低音強化] (預設)、[標準]、[高音提升] 之間進行切換。

注意：耳塞套大小可能會影響您聽到的低音音域。

9

10

如何使用

aptX

- 耳機配備 aptX 技術，可確保透過藍牙傳輸的音訊內容不

僅順暢且音質清晰。

- 只要來源裝置支援，aptX 即會自動啟用。

Tone & Talk

HBS-850 藍牙耳機支援在 Android TM 裝置上讀出文字訊息。

若要下載此應用程式，請在 Google Play TM * 中搜尋

Tone & Talk 或掃描 QR 碼。 請按照安裝指示操作。

*Google Play 是 Google, Inc. 的商標。

功能

目前時間提示

讀出最新的文

字訊息或多媒

體訊息

動作

按住 [音量調低] 按鈕 1 秒鐘。

按住 [音量調高] 按鈕 1 秒鐘。

指定聯絡人

最愛聯絡人

1. 在應用程式的耳機通話設定中選擇指定

聯絡人。

2. 若要撥打電話給指定聯絡人，請同時按住

[音量調高] 和 [音量調低] 按鈕 1 秒鐘。

1. 在應用程式的耳機通話設定中選擇最愛

聯絡人。

2. 同時按住耳機上的 [音量調高] 和 [音量調低]

按鈕 1 秒鐘。

3. 使用 [音量] 按鈕選擇聯絡人。

4. 若要撥打電話給最愛聯絡人，請同時按住

[音量調高] 和 [音量調低] 按鈕 1 秒鐘。

如何使用

功能

通話記錄

動作

1. 在應用程式的耳機通話設定中選擇通

話記錄。

2. 同時按住耳機上的 [音量調高] 和 [音量調低]

按鈕 1 秒鐘。

3. 使用 [音量] 按鈕選擇聯絡人。

4. 若要撥打電話給聯絡人，請同時按住 [音量

調高] 和 [音量調低] 按鈕 1 秒鐘。

功能

操作中

充電中

LED 指示燈

耳機狀態

配對模式

耳機/免持操作模式

已連線

來電已接通

充電中

充電完成

指示

持續亮藍色 LED 燈。

藍色 LED 燈閃爍 1 次。

藍色 LED 燈閃爍 1 次。

持續亮紅色 LED 燈，並

會在充電至 80% 以上時

轉為紫色。

持續亮藍色 LED 燈。

11

12

疑難排解

問題

沒有開機

無法與 LG 藍

牙耳機

HBS-850 通訊

可能原因

檢查耳機的電池是

否已充滿。

檢查您嘗試配對的

行動裝置是否支援

耳機或免持藍牙操

作模式。

檢查耳機的電池電

力是否不足。

可能的解決方法

為電池充電。

判斷您的行動裝置是

否支援耳機或免持藍

牙操作模式。

為電池充電。

問題 可能原因

檢查並確認耳機電

源已開啟。

耳機無法與藍

牙裝置配對

檢查並確認耳機處

於配對模式。

音量太小

(喇叭)

檢查喇叭音量。

可能的解決方法

按住 [電源] (PWR)

按鈕 2 秒鐘以開啟

耳機。

在電源關閉時同

時按住 [多功能按

鈕] (MFB) 和 [電源]

(PWR) 按鈕 2 秒鐘，

即可使耳機進入 [手

動配對] 模式。

增加音量。

藍牙版本

電池

通話時間

音樂播放時間

待機時間

充電時間

額定輸入功率

操作溫度

尺寸/重量

項目 說明

4.1 (耳機/免持裝置/A2DP 操作模式)

電池 3.7 V/180 鋰聚合物電池

多達 13 小時

長達 9.5 小時

長達 430 小時

低於 2 小時

DC 4.75 V ~ 5.3 V，400 mA

-10°C ~ 60°C

141 公釐 (寬) x 140 公釐 (長) x 16.1 公釐 (高) / 51 公克

規格

13

注意事項

14

請勿摔落裝置。

請勿改裝、維修，或拆卸裝置。

請勿直接使用水、酒精或苯等溶劑清潔裝置。

請勿直接接觸火源。

裝置必須遠離火源。

裝置必須遠離過重的濕氣與灰塵。

請勿在裝置上放置重物。

僅限使用原廠 LG 充電器為耳機充電，否則可能導致耳機損壞。

• 若負責遵循法規者未獲明文同意即變更或修改裝置，則可能喪失設備的使用權益。

• 使用不正確的電池可能有損壞或爆炸的危險。

• 請根據指示丟棄使用過的電池。

• 本產品內含耳塞套、耳塞及連接線等細小零件。 請放置在孩童無法拿取之處。

• 如果您體內有植入式醫療裝置，使用本產品前請先諮詢醫師。

• 若要避免產品變色，請勿將產品長時間直接曝曬於陽光下。

• 產品充完電後務必將充電器自插座移除，以節省充電器不必要的電力損耗。

• 如果您需要更換電池，請將電池送到距離最近的授權 LG Electronics 服務中心或經銷商處尋求協助。

• 鋰離子電池為可能造成傷害的危險元件。

• 由非合格專業人員替換電池可能對裝置造成損壞。

使用者 FCC 聲明：

本裝置符合 FCC 規則第 15 節。

必須遵守下列兩個操作條件：

(1) 本裝置不得引起有害干擾，且

(2) 本裝置必須可承受接收到的干擾，包括可能導致預期外

操作之干擾。

重要注意事項：

為了符合 FCC RF 放射物需求，不得對天線或裝置進行變

更。 若對天線或裝置進行任何變更，可能導致裝置超出 RF

放射物要求，並中止使用者操作裝置之授權。

確認宣告

符合性聲明 :

LG Electronics 謹此宣告此 HBS-850 產品符合基本要求

1999/5/EC 的其他相關條款。 可於下列連結取得符合性聲明

的副本：http://www.lg.com/global/declaration

Bluetooth ® 是 Bluetooth SIG, Inc. 的全球註冊商標。

FCC ID: BEJHBS850

15

16

其他資訊

1. 無線電頻率放射

HBS-900 這款 Bluetooth 耳機是一種無線電傳輸器及接

收器。 操作中的耳機會接收與傳輸頻率範圍在 2.4 至

2.4835 GHz 的無線電頻率 (RF) 電磁場 (微波)，藉此與配備

Bluetooth 的行動裝置通訊。 當您的 Bluetooth 耳機與任何相

容的行動電話搭配使用時，必須遵守國家機構和國際健康

機構所制定的 RF 放射線指導方針與限制。

2. 具有潛在爆炸危險的環境

當您身在具有潛在爆炸性風險的任何區域時，請關閉您的

電子裝置。 您的電子裝置可能會產生火花，雖然這種現象

非常罕見。 在這類區域產生火花可能造成爆炸或火災，從

而導致身體受傷，甚至死亡。 具有潛在爆炸性的區域經

常、但並非總是會有明確的標示。

3. 電池資訊

適當使用的充電電池使用期限較長。 全新的電池或長時間

未使用的電池，前幾次的使用容量可能會降低。 請勿將電

池曝露在超過 +60° C (+140° F) 或低於 -20° C (-4° F) 的極端溫

度下。 為了使用最大的電池容量，請在室溫下使用電池。

如在低溫下使用電池，電池容量會降低。 電池只能在 +10°

C (+50° F) 至 +45° C (+113° F) 之間的溫度充電。 為了您的安

全考量，請勿將產品內建的電池取出。 如果您需要更換電

池，請將裝置帶到附近的 LG Electronics 授權服務中心或經

銷商處以尋求協助。

4. 回收 Bluetooth 耳機的電池

Bluetooth 耳機的電池必須適當處置，絕對不能隨一般廢棄

物一起處理。 取出電池的 LG Electronics 服務夥伴將依據當

地法規處置電池。

5. 條件

- 唯有當業者提供給原始購買者的原始收據有指定購買日

期和序號，且在維修或更換產品出示該收據時，保固才

會生效。 若向業者初次購買產品後，此資訊已移除或變

更，LG Electronics 將保留拒絕保固服務之權利。

- 此保固不包含下列因素所導致的任何產品故障：正常損壞

或撕裂，或者不當使用，包括但不限於異常及不依慣例使

用、不依照指示來使用和維護產品。 此保固亦不涵蓋下列

原因所導致的任何產品故障：意外、修改或調整、天災，

或者液體潑灑所導致的損壞。

- 此保固不涵蓋非 LG Electronics 授權人員所執行之不當維修

安裝、修改或服務所造成的產品故障。 損毀產品的任何

封條將中止保固。

其他資訊

17

18

有限保固

在此有限保固條款中，LG Electronics 保證消費者在原始購買本產品時，產品之設計、材料與製作上並無瑕疵，並在該日起

一年內亦享有同等保固。 如果您的產品需要保固服務，請將產品送回出售之業者，或聯絡您當地的 LG Electronics 聯絡中

心以取得進一步資訊。

避免損害聽力：如果您在高音量下使用耳機，可能會對聽

力造成永久性的損害。 請設定安全等級的音量。 過了一

段時間，您可能會習慣較大的音量並將其視為正常音量，

但此音量可能會使您的聽力受損。 如果您聽到嗡嗡聲或

聽不清楚話語，請停止聆聽並檢查聽力。 音量越大，越

可能加速聽力受損的時間。 聽力專家提出了下列保護聽

力的建議：

• 限制在高音量下使用耳機的時間。

• 避免調大音量來阻絕周圍噪音。

• 如果您聽不到周遭他人的談話聲，請調

低音量。

請參閱手機使用者指南，瞭解更多關於如何在手機上調整

音量的資訊。

重要的安全資訊

安全地使用耳機：不建議您在開車時使用耳機聽音樂，且

這種行為在某些地區是違法的。 開車時請小心並集中注

意力。 駕駛任何類型的車輛或執行需要全神貫注的其他

任何活動時，若發現使用此裝置可能會分神或產生混亂，

請停止使用。

19

HBS-850

User Manual

Bluetooth

®

Stereo Headset

All rights reserved. LG Electronics Inc., 2015

Note: For the best performance and to prevent any damage to, or misuse of the HBS-850, please read all of the information carefully prior to using the HBS-850.

Any modifications or changes to this manual due to typographical errors or inaccuracies of stated information shall only be made by LG Electronics Inc.

English

Introduction

The LG TONE Active TM (HBS-850) is a lightweight wireless headset that uses Bluetooth ® technology.

This product can be used as an audio accessory for devices supporting either the A2DP or hands-free Bluetooth profile.

Included in the Package

2

Extra Ear Gels

(1 Set - Small)

HBS-850

(Medium Ear Gels and Stabilizer Tips installed)

Extra Stabilizer Tips

(1 Set - Small)

*USB Charging

Cable

*Actual product design may differ from images shown in this manual.

User Manual

Headset

Volume Up

Button/

Previous

Song

Volume Down

Button/

Next Song

Earbud (R)

Description of Parts

Charging Port

LED Indicator

Microphone

Power

Button

MFB

(Multi-Function

Button)

Stabilizer Tips Earbud (L)

3

4

Description of Parts

Stabilizer Tip Replacement

- An extra set of Stabilizer Tips is included. Depending on your neck size, you may want to change the size of the

Stabilizer Tips for comfort and fit.

1

Stabilizer Tip Removal

2 1

Stabilizer Tip Installation

3 4 2

3

Power On/Power Off

- Power On: Press and hold the PWR button for 2 seconds.

- Power Off: Press and hold the PWR button for 3 seconds.

Charging

- When the charger is connected (with the power on or off) the headset will power off.

- While charging, the LED indicator will show a solid red light. When charged 80% or more, the indicator will show a violet light.

- When the device is fully charged, the LED indicator will show a solid blue light.

Low Battery

- A low battery alert will play once every 2 minutes.

- If the battery is not charged, the headset will power off.

How to Use

Battery Status Alert

- Press and hold the Volume Down button for 3 seconds to check the battery status of the headset.

Battery

Status

Voice

Prompt

LED

Indicator

High

Battery High

Blinking

Blue

Medium

Battery

Medium

Blinking

Violet

Low

Battery Low

Blinking

Red

NOTE: When paired, some mobile devices may display the headset's battery level at the top of the screen.

Retractable Earbuds

- Pull the earbuds to extend them to the desired length.

- To retract the earbuds, pull the cords out slightly, and they will automatically retract into place.

- If the earbuds do not retract, pull the earbuds out completely to retract them.

5

6

How to Use

Pairing

- To use the headset, you must first pair it with your mobile device. Once the devices have been paired, the headset will automatically reconnect.

1) Easy Pairing

1. Press and hold the PWR button for 2 seconds to power on the headset.

2. If it is your first time pairing the device or it does not detect a previously paired device, it will enter Pairing mode. The LED indicator will be solid blue.

3. On the device you wish to pair with, find the Bluetooth menu and search for or add new devices.

4. Select LG HBS850 from the list of devices.

5. If asked for a Pass/Pin Code, enter 0000 (4 zeros).

6. Once the devices are paired, you will hear “Your headset paired.”

NOTE: The headset will automatically power off if not paired within 3 minutes.

2) Manual Pairing (pairing with another phone or re-pairing)

1. With the power off, press and hold the MFB and the

PWR button at the same time for 2 seconds to enter

Manual Pairing mode.

2. When the headset enters Pairing mode, the LED indicator will show a solid blue light. Repeat Easy

Pairing steps 3 through 6.

Advanced Multipoint

The headset can be connected to two devices at the same time. This will give you the freedom to use call waiting between calls on both of your connected phones.

Pairing with Two Devices

- First, pair the headset with the Bluetooth-enabled mobile device you want to use as your secondary device (see

Pairing instructions).

- Once paired, power off the headset.

- With the power off, press and hold the MFB and the

PWR button at the same time for 2 seconds. This will activate Manual Pairing mode.

- Pair and connect the headset with your other Bluetoothenabled mobile device. This will be your primary device.

- Once the primary mobile device is paired and connected with the headset, reconnect the headset to the initially paired mobile device.

NOTE: When the headset is connected to two mobile devices at the same time (Multipoint), the headset calling functions will work with the primary mobile device.

NOTE: If the headset fails to connect to the primary phone through Easy Pairing, it will enter Pairing mode.

Calling Function

- Voice Dialing and Last Number Redial features work with the primary mobile device (or the mobile device that made the last outgoing call).

Call Waiting

- While on a call, press and hold the MFB for 1 second to answer an incoming call.

- To switch between two active calls, press and hold the

MFB for 1 second.

- To end both calls, briefly press the MFB.

- If both paired mobile devices are receiving an incoming call, the headset will default to the primary device.

How to Use

Auto Reconnect

- If in range of each other when the headset is powered on, the headset and the primary mobile device will automatically reconnect.

- The secondary mobile device will need to be manually connected. Select LG HBS850 from the list of devices in the

Bluetooth menu and connect.

Out of Range

- If the paired devices are separated by a range of 33 feet (10 meters) or more, the headset and paired mobile device(s) will disconnect, and the headset will vibrate to alert you.

NOTE: To power off device vibration, press and hold the

Volume Up button for 3 seconds.

- If the headset and paired mobile device do not automatically reconnect when they are back within the required range, briefly press the MFB on the headset to manually reconnect.

- While in multi-connection and streaming, the inactive paired device will be disconnected when out of range.

The headset will alert you once with no attempt to reconnect.

7

8

How to Use

Calling

Answering a Call

- When receiving an incoming call, the headset will ring and vibrate.

- Briefly press the Volume Down button to stop the vibration.

NOTE: The headset will not vibrate if vibration has been deactivated.

- Briefly press the MFB to answer the incoming call.

Transferring a Call

- You can manually transfer the call to or from the headset by pressing the Volume Up button for 2 seconds on the headset (mobile device and headset must be paired).

Voice Dialing

- Press and hold the MFB for 1 second to activate Voice

Command.

NOTE: If your mobile device does not support voice dialing, this action may activate Last Number Redial.

Last Number Redial

- Press and hold the MFB for 2 seconds to activate Last

Number Redial. The headset will call the last number dialed.

Ending a Call

- Briefly press the MFB.

Call Waiting

- Answer a second call without hanging up the first call by pressing the MFB for 1 second. Press and hold the MFB for

1 second to return to the first call.

- Briefly press the MFB to end both calls.

Rejecting a Call

- Activate Call Reject by pressing the MFB for 2 seconds when the mobile device rings.

NOTE: These functions may not be available on all mobile devices. For further information about using these features, please consult your mobile device’s user manual.

Microphone Mute

- Press and hold the Volume Up and Volume Down buttons at the same time for 1 second to mute/unmute the microphone during conversation.

Volume Control

- Press the Volume buttons to adjust the speaker volume.

Caution: Listening to music for long periods of time at high volume levels may cause hearing damage or loss. To prevent this, the headset will emit a warning beep when you are using the upper six volume levels.

Vibration Control

- To activate or deactivate device vibration, press and hold the Volume Up button for 3 seconds. You will hear “Vibrate on” or “Vibrate off” when it is activated or deactivated.

- When vibration is deactivated, the headset will not vibrate when receiving an incoming call or when it is out of range of a paired mobile device.

- Vibration will be automatically reactivated when the device is powered on.

How to Use

Audio Streaming

Play

- Briefly press the MFB.

Pause

- While playing music, briefly press the MFB.

Next song

- Press and hold the Volume Down button for 1 second.

Previous song

- Press and hold the Volume Up button for 1 second.

Equalizer

- While playing music, press and hold the MFB for

2 seconds to switch between Bass Boost (default),

Normal, and Treble Boost.

NOTE: The size of the ear gel can affect the amount of bass you hear.

9

10

How to Use

aptX

- The headset features aptX technology that ensures audio content transmitted via Bluetooth is seamless and crystal clear.

- aptX is automatically enabled as long as the source device supports it.

Tone & Talk

The HBS-850 Bluetooth headset supports SMS reading on

Android TM -based devices.

To download the app, search for Tone & Talk in Google

Play TM * or scan the QR code. Follow the installation instructions.

*Google Play is a trademark of Google, Inc.

Function

Current time alert

Read latest

SMS or MMS

Designated contact

Favorite contacts

Action

Press and hold the Volume Down button for

1 second.

Press and hold the Volume Up button for

1 second.

1. Select Designated contact in the headset call settings of the app.

2. To call the Designated contact, press and hold the Volume Up and Volume Down buttons at the same time for 1 second.

1. Select Favorite contacts in the headset call settings of the app.

2. Press and hold the Volume Up and Volume

Down buttons at the same time for 1 second on your headset.

3. Use the Volume buttons to choose the contact.

4. To call the Favorite contact, press and hold the Volume Up and Volume Down buttons at the same time for 1 second.

Function

Call logs

How to Use

Action

1. Select Call logs in the headset call settings of the app.

2. Press and hold the Volume Up and Volume

Down buttons at the same time for 1 second on your headset.

3. Use the Volume buttons to choose the contact.

4. To call the contact, press and hold the

Volume Up and Volume Down buttons at the same time for 1 second.

LED Indicator

Function

Operating

Charging

Headset Status

Pairing mode

Headset/hands-free profile connected

Call connected

Charging

Charging complete

Indicator

Solid blue LED light.

The blue LED light flickers 1 time.

The blue LED light flickers 1 time.

Solid red LED light, which changes to violet when charged 80% or more.

Solid blue LED light.

11

12

Troubleshooting

Problem

Does not power on

Unable to communicate with the LG

Bluetooth

Headset

HBS-850

Possible Causes

Check whether the battery of the headset is fully charged.

Check whether the mobile device you are trying to pair supports the headset or handsfree Bluetooth profiles.

Check whether the battery of the headset is low.

Possible Solution

Charge the battery.

Determine whether your mobile device supports the headset or hands-free

Bluetooth profiles.

Charge the battery.

Problem

Unable to pair the headset with the Bluetooth device

Low sound

(speaker)

Possible Causes

Check to make sure the headset is on.

Check to make sure the headset is placed in Pairing mode.

Check the speaker volume.

Possible Solution

Press and hold the

PWR button for 2 seconds to power on the headset.

With the power off, press and hold the

MFB and the PWR button at the same time for 2 seconds to place the headset in Manual Pairing mode.

lncrease the volume level.

Item

Bluetooth version

Battery

Talk time

Music play time

Standby time

Charging time

Rated input power

Operation temperature

Dimensions/weight

Description

4.1 (Headset/Hands-Free/A2DP profiles)

Battery 3.7 V/180 mAh Li-Polymer

Up to 13 hours

Up to 9.5 hours

Up to 430 hours

Less than 2 hours

DC 4.75 V ~ 5.3 V, 400 mA

-10°C ~ 60°C

141 mm (W) x 140 mm (L) x 16.1 mm (H) / 51 g

Specifications

13

14

Precautions

Do not drop the device.

Do not modify, repair, or disassemble.

Do not expose directly to water, alcohol, benzene, etc., for cleaning.

Do not expose directly to flammables.

Do not place or keep the device near flammables.

Keep the device away from excessive humidity and dust.

Do not place heavy objects on the device.

Only charge the headset with an original LG charger, otherwise it may be damaged.

• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

• Risk of damage or explosion if incorrect battery is used.

• Dispose of used batteries according to the instructions.

• This product contains small parts, including ear gels, earbuds, stabilizer tips, and cables. Keep out of reach of children.

• If you have an implanted medical device, consult with a doctor prior to using this product.

• To prevent potential discoloration, please make sure the product is not exposed to direct sunlight for an excessive period of time.

• Always unplug the charger from the wall socket after the product is fully charged to save unnecessary power consumption of the charger.

• If you need to replace the battery, take it to the nearest authorized LG Electronics service point or dealer for assistance.

• Li-ion Battery is a hazardous component which can cause injury.

• Battery replacement by non-qualified professional can cause damage to your device.

FCC NOTICE TO USERS:

This device complies with part 15 of the FCC rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference and

(2) This device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE:

To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.

Declaration of Confirmation

DECLARATION OF CONFORMITY :

Hereby, LG Electronics declares that this HBS-850 is in compliance with the essential requirements and other relevant provisions of Directive1999/5/EC. A copy of the

Declaration of Conformity can be found at http://www.

lg.com/global/declaration

Bluetooth ® is a registered trademark of Bluetooth SIG,

Inc. worldwide.

FCC ID: BEJHBS850

15

16

Additional Information

1. Radio frequency exposure

This Bluetooth Stereo Headset HBS-850 is a radio transmitter and receiver. When in operation, it communicates with a Bluetooth equipped mobile device by receiving and transmitting radio frequency (RF) electromagnetic fields (microwaves) in the frequency range 2.4 to 2.4835 GHz.

Your Bluetooth Headset is designed to operate in compliance with the RF exposure guidelines and limits set by national authorities and international health agencies when used with any compatible LG Electronics mobile phone.

2. Potentially explosive atmosphere

Turn off your electronic device when in any area with a potentially explosive atmosphere. It is rare, but your electronic device could generate sparks. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death. Areas with a potentially explosive atmosphere are often, but not always, clearly marked.

3. Battery information

A rechargeable battery has a long service life if treated properly. A new battery or one that has not been used for a long period of time could have reduced capacity the first few times it is used. Do not expose the battery to extreme temperatures, never above +60° or below -10°.

For maximum battery capacity, use the battery in room temperature. If the battery is used in low temperatures, the battery capacity will be reduced. The battery can only be charged in temperatures between +10° and +45°.

4. Recycling the battery in your Bluetooth Headset

The battery in your Bluetooth Headset must be disposed of properly and should never be placed in municipal waste.

5. Conditions

- The warranty is valid only if the original receipt issued to the original purchaser by the dealer, specifying the date of purchase and serial number, is presented with the product to be repaired or replaced. LG Electronics reserves the right to refuse warranty service if this information has been removed or changed after the original purchase of the product from the dealer.

- If LG Electronics repairs or replaces the product, the repaired or replaced product shall be warranted for the remaining time of the original warranty period or for ninety (90) days from the date of repair, whichever is longer. Repair or replacement may involve the use of functionally equivalent reconditioned units. Replaced parts or components will become the property of LG

Electronics.

Additional Information

- This Warranty does not cover any failure of the product due to normal wear and tear, or due to misuse, including but not limited to use in other than the normal and customary manner, in accordance with instructions for use and maintenance of the product. Nor does this warranty cover any failure of the product due to accident, modification or adjustment, acts of God or damage resulting from liquid.

- This warranty does not cover product failures due to improper repair installations, modifications or service performed by a non-LG Electronics authorized person.

Tampering with any of the seals on the product will void the warranty.

17

18

Limited Warranty

SUBJECT TO THE CONDITIONS OF THIS LIMITED WARRANTY, LG ELECTRONICS WARRANTS THIS PRODUCT TO BE

FREE FROM DEFECTS IN DESIGN, MATERIAL AND WORKMANSHIP AT THE TIME OF ITS ORIGINAL PURCHASE BY

A CONSUMER, AND FOR A SUBSEQUENT PERIOD OF ONE (1) YEAR. SHOULD YOUR PRODUCT NEED WARRANTY

SERVICE, PLEASE RETURN IT TO THE DEALER FROM WHOM IT WAS PURCHASED OR CONTACT YOUR LOCAL LG

ELECTRONICS CONTACT CENTER TO GET FURTHER INFORMATION.

Avoiding hearing damage

Permanent hearing loss may occur if you use your

Handsfree car kit at a high volume. Set the volume to a safe level. You can adapt over time to a higher volume of sound that may sound normal but can be damaging to your hearing.

If you experience ringing in your ears or muffled speech, stop listening and have your hearing checked. The louder the volume, the less time is required before your hearing could be affected. Hearing experts suggest that to protect your hearing:

• Limit the amount of time you use Headset at high volume.

• Avoid turning up the volume to block out noisy surroundings.

• Turn the volume down if you can’t hear people speaking near you.

Please refer to your handset user guide for more information on how to adjust listening levels on your handset.

Important Safety Information

Using headsets safely

Use of Headset to listen to music while operating a vehicle is not recommended and is illegal in some areas. Be careful and attentive while driving. Stop using this device if you find it disruptive or distracting while operating any type of vehicle or performing any other activity that requires your full attention.

19