LG | HT805SH | LG HT805SH Owner’s Manual

OWNER’S MANUAL
DVD Receiver System
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
HT805SH (HT805SH, SH85SH-F/ S/ C/ W)
P/NO : MFL63726924
HT805SH-F2_BLKALL_ENG_6924.indd 1
2010-03-10 ¿ÀÈÄ 4:01:50
1
Safety Information
Safety Information
1
Safety Information
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK) NO USERSERVICEABLE PARTS INSIDE REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral triangle is
intended to alert the user to the presence
of uninsulated dangerous voltage within
the product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a
dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an exact
replacement part by an authorized service center.
Protect the power cord from physical or mechanical
abuse, such as being twisted, kinked, pinched, closed
in a door, or walked upon. Pay particular attention
to plugs, wall outlets, and the point where the cord
exits the appliance. To disconnect power from the
mains, pull out the mains cord plug. When installing
the product, ensure that the plug is easily accessible.
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance,
contact an authorized service center.
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try
to open the enclosure. Visible laser radiation when
open. DO NOT STARE INTO BEAM.
HT805SH-F2_BLKALL_ENG_6924.indd 2
2010-03-10 ¿ÀÈÄ 4:01:51
Safety Information
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
This device is equipped with a portable battery or
accumulator.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer's
instructions.
Safe way to remove the battery or the battery
from the equipment:
1
Safety Information
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from overheating.
The openings should be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product should not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer's
instruction have been adhered to.
Remove the old battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put in the appropriate
container at designated collection points. Do not
dispose of batteries or battery together with other
waste. It is recommended that you use local, free
reimbursement system batteries and accumulators.
The battery shall not be exposed to excessive heat
such as sunshine, fire or the like.
Copyrights
It is forbidden by law to copy, broadcast, show,
broadcast via cable, play in public, or rent
copyrighted material without permission. This
product features the copy protection function
developed by Macrovision. Copy protection signals
are recorded on some discs. When recording and
playing the pictures of these discs picture noise
will appear. This product incorporates copyright
protection technology that is protected by U.S.
patents and other intellectual property rights. Use
of this copyright protection technology must be
authorized by Macrovision, and is intended for home
and other limited viewing uses only unless otherwise
authorized by Macrovision. Reverse engineering or
disassembly is prohibited.
CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE
WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS
TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525
OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS,
IT IS RECOMMENDED THAT THE USER SWITCH THE
CONNECTION TO THE ‘STANDARD DEFINITION
’ OUTPUT. IF THERE ARE QUESTIONS REGARDING
OUR TV SET COMPATIBILITY WITH THIS MODEL 525p
AND 625p UNIT, PLEASE CONTACT OUR CUSTOMER
SERVICE CENTER.
You have to set the disc format option to [Mastered]
in order to make the discs compatible with the LG
players when formatting rewritable discs. When
setting the option to Live File System, you cannot
use it on LG players.
(Mastered/ Live File System : Disc format system for
Windows Vista)
HT805SH-F2_BLKALL_ENG_6924.indd 3
2010-03-10 ¿ÀÈÄ 4:01:51
Contents
Contents
19
AUX In Connection
19
AUDIO (PORT. IN) In
19
Listening to music from your
Connection
1
portable player or external
Safety Information
2
2
CAUTION
Preparation
3
4
5
6
7
20
USB Connection
21
OPTICAL In connection
21
Antenna Connection
22
Adjust the setup settings
6
Unique Features
22
OSD Initial language settings
6
Accessories
22
To display and exit the Setup
7
Introduction
7
Playable Discs
7
About the  Symbol Display
7
Symbol Used in this Manual
7
Regional Codes
8
Playable file Requirement
9
Remote control
11
Front panel
12
Rear panel
Installation
device
menu
23
Language
23
Display
24
Audio
25
Lock (Parental Control)
26
Others
Operation
27
Using the Home Menu
27
Basic Operations
28
Other Operations
28
Displaying Disc Information on-
13
Attaching the speakers to the unit
14
Positioning the system
29
To display the DVD Menu
15
Connections to Your TV
29
To display the DVD title
Component Video Connection
29
1.5 times speed playback
16
HDMI Out Connection
29
Screen Saver
17
Video Connection
29
Starting play from selected
18
Resolution Setting
29
Resume playback
30
Marked Playback
15
18
Video Output Resolution
19
Optional Equipment Connection
HT805SH-F2_BLKALL_ENG_6924.indd 4
screen
time
2010-03-10 ¿ÀÈÄ 4:01:51
Contents
Appendix
30
Changing subtitle code page
31
Viewing a PHOTO file
31
Options while viewing a photo
38
Language Codes
32
Sleep Timer Setting
39
Area Codes
32
Dimmer
32
Turn off the sound temporarily
40
Trademarks and Licenses
32
Last Scene Memory
41
Specifications
32
System Select - Optional
32
Adjust the speaker level
1
2
settings
32
33
VOCAL FADER
Radio Operations
33
Presetting the Radio Stations
33
Deleting all the saved stations
33
Deleting a saved station
33
Improving poor FM reception
34
34
4
Sound adjustment
Setting the surround mode
35
Advanced Operations
35
Recording to USB
Maintenance
36
Notes on Discs
36
Handling the Unit
Troubleshooting
37
3
5
6
7
Troubleshooting
HT805SH-F2_BLKALL_ENG_6924.indd 5
2010-03-10 ¿ÀÈÄ 4:01:51
Preparation
2
Preparation
2
Preparation
Unique Features
Accessories
Portable In
Please check and identify the supplied
accessories.
Listens to music from your portable device.
(MP3, Notebook, etc)
USB Direct Recording
Records music from CD to your USB device.
Video cable (1)
Battery (1)
Remote control (1)
FM antenna (1)
Full HD up-scaling
Views Full HD picture quality with simple setup.
Home Theater Speaker ez
Setup
listens sound from TV, DVD and Digital device
with vivid 5.1 (2.1 or 2.0) ch mode.
HDMI cables (1)
HT805SH-F2_BLKALL_ENG_6924.indd 6
2010-03-10 ¿ÀÈÄ 4:01:52
Preparation
Introduction
Playable Discs
DVD-VIDEO (8 cm / 12 cm disc)
Discs such as movies that can be
purchased or rented.
DVD±R (8 cm / 12 cm disc)
Video mode and finalized only
DVD-RW (8 cm / 12 cm disc)
Video mode and finalized only
DVD+R: Video mode only
Supports the double layer disc
also
DVD+RW (8 cm / 12 cm disc)
Video mode and finalized only
Audio CD: Music CDs or CD-R/CDRW in music CD format that can
be purchased.
About the  Symbol Display
“  ” may appear on your TV display during
operation and indicates that the function
explained in this owner’s manual is not
available on that disc.
HT805SH-F2_BLKALL_ENG_6924.indd 7
Symbol Used in this Manual
All discs and file listed below ALL
MP3 files MP3
DVD and finalized DVD±R/RW
DVD
WMA files WMA
DivX files DivX
Audio CDs ACD
JPG files
JPG
NOTE
2
Preparation
This unit plays DVD±R/RW and CD-R/RW that
contains audio titles, DivX, MP3, WMA and/or
JPEG files. Some DVD±RW/DVD±R or CDRW/CD-R cannot be played on this unit due to
the recording quality or physical condition of
the disc, or the characteristics of the recording
device and authoring software.
Indicates special notes and operating features.
TIP
Indicates tip and hints for making the task
easier.
CAUTION
Indicates cautions for preventing possible
damages from abuse.
Regional Codes
This unit has a regional code printed on the
rear of the unit. This unit can play only DVD
discs labeled same as the rear of the unit or
“ALL”.
• Most DVD discs have a globe with one or
more numbers in it clearly visible on the
cover. This number must match your unit’s
regional code or the disc cannot play.
• If you try to play a DVD with a different
regional code from your unit, the message
“Check Regional Code” appears on the TV
screen.
2010-03-10 ¿ÀÈÄ 4:01:53
Preparation
Playable file
Requirement
MP3/ WMA music file requirement
2
MP3/ WMA file compatibility with this unit is
limited as follows :
Preparation
• Sampling frequency : within 32 to 48 kHz
(MP3), within 32 to 48 kHz (WMA)
• Bit rate : within 32 to 320 kbps (MP3),
40 to 192 kbps (WMA)
• Support Version : v2, v7, v8, v9
• Maximum files : Under 999
• File extensions : “.mp3”/ “.wma”
• CD-ROM file format : ISO9660/ JOLIET
• We recommend that you use Easy-CD
Creator, which creates an ISO 9660 file
system.
DivX file requirement
DivX file compatibility with this unit is limited
as follows :
• Available resolution: within 720x576 (W x H)
pixels.
• The file name of the DivX subtitle should be
entered within 45 characters.
• If there is impossible code to express in the
DivX file, it may be displayed as " _ " mark
on the display.
• Frame rate : less than 30 fps.
• If the video and audio structure of recorded
files is not interleaved, either video or audio
is outputted.
• Playable DivX file : ".avi", ".mpg", ".mpeg",
".divx"
• Playable Subtitle format : SubRip (*.srt/
*.txt), SAMI (*.smi), SubStation Alpha (*.ssa/
*.txt), MicroDVD (*.sub/ *.txt), SubViewer 2.0
(*.sub/ *.txt), Vobsub (*.sub)
• Playable Codec format : "DIVX3.xx", "DIVX4.
xx", "DIVX5.xx", "MP4V3", "3IVX".
Photo file requirement
• Playable Audio format : "AC3", "PCM", "MP3",
"WMA".
Photo file compatibility with this unit is limited
as follows :
• Sampling frequency : within 32 to 48 kHz
(MP3), within 32 to 48 kHz (WMA)
• Max pixel in width : 2760 x 2048 pixel
• Bit rate : within 32 to 320 kbps (MP3), 40 to
192 kbps (WMA)
• Maximum files : Under 999
• Some discs may not operate due to a
different recording format or the condition
of disc.
• File extensions: “.jpg”
• CD-ROM file format : ISO9660/ JOLIET
HT805SH-F2_BLKALL_ENG_6924.indd 8
• For Discs formatted in Live file system, you
can not it on this unit.
• If the name of movie file is different from
that of the subtitle file, during playback of a
DivX file, subtitle may not be display.
• If you play a DivX file differ from DivXspec, it
may not operate normally.
2010-03-10 ¿ÀÈÄ 4:01:53
Preparation
Remote control
Remote control
1 POWER : Switches the unit ON or OFF.
Z OPEN/CLOSE : Opens and closes the disc
Drawer.
SLEEP : Sets the System to turn off
automatically at a specified time. (Dimmer :
The display window will be darken by half.)
INFO/DISPLAY : Accesses On-Screen Display.
a
HOME: Displays the [Home] menu.
b
U/u/I/i (up/ down/ left/ right): Used to
navigate on-screen displays.
Preparation
DISC MENU : Accesses the menu on a DVD
disc.
• • • • • • • • • • b • • • • • • • • • 2
PRESET (+/-) : Selects programme of Radio.
TUNING -/+ : Tunes in the desired radio station.
c
d
e
f
 ENTER : Acknowledges menu selection.
Presetting the radio stations.
O RETURN : Moves backwards in the menu
or exits the setup menu.
TITLE : If the current DVD title has a menu, the
title menu appears on the screen. Otherwise,
the disc menu may not appear.
• • • • • • • • • • c • • • • • • • • • ./> SKIP : Goes to next or previous
chapter/ track/ file.
m/M SCAN : Searchs backward or forward.
x STOP : Stops playback or recording.
B PLAY, MONO/STEREO : Starts playback.
Selects Mono/ Stereo.
X PAUSE/STEP : Pauses playback.
Put the battery into the remote control
• • • • • • • • • • a • • • • • • • • • t RADIO&INPUT: Changes input sources.
Make sure for the + (plus) and – (minus) on
the battery to be matched on the remote
control.
MARKER : Marks play list.
HT805SH-F2_BLKALL_ENG_6924.indd 9
2010-03-10 ¿ÀÈÄ 4:01:53
10
Preparation
Remote control
a
• • • • • • • • • • e • • • • • • • • • 0-9 numerical buttons : Selects numbered
options in a menu.
CLEAR : Removes a number when setting the
password.
s REPEAT : Selects a play mode. (Repeat/
Random)
• • • • • • • • • • f • • • • • • • • • 2
Preparation
b
TV Control buttons : Controls the TV. (LG TV
only)
z REC : USB Direct Recording.
: This button is not available.
c
ECHO VOL : Adjusts echo volume.
MIC VOL : Adjusts microphone volume.
d
e
f
VOCAL FADER : You can enjoy the function as
karaoke, by reducing singer vocal of music in
the various source.
Controlling the TV.
You can control the sound level, input
source, and power switching of LG TVs as
well. Hold POWER (TV) and press PR/CH
(U/u) button repeatedly until the TV turns
on or off.
• • • • • • • • • • d • • • • • • • • • SPEAKER LEVEL: Sets the sound level of
desired speaker.
SOUND EFFECT: Selects a sound effect mode.
VOL -/+ (Volume) : Adjusts speaker volume.
OPTICAL: Changes input source to optical
directly.
MUTE : Mutes the sound.
HT805SH-F2_BLKALL_ENG_6924.indd 10
2010-03-10 ¿ÀÈÄ 4:01:53
Preparation
11
Front panel
a
b
c
d
2
l kj
Preparation
ihg f e
a 1/\ (POWER)
Switches the unit ON or OFF.
g x (STOP)
Stops playback.
b Disc Tray
h N/X (PLAY / PAUSE)
Starts playback.
Pause playback temporarily, press again to
exit pause mode.
c Display window
Shows the current status of the unit.
d VOLUME
Adjusts speaker volume.
e F (FUNCTION)
Changes the input source or function.
f ./> (SKIP)
Go to next or previous file/track/chapter.
Searches backward or forward (Press and
hold)
Tunes in the desired radio station.
HT805SH-F2_BLKALL_ENG_6924.indd 11
i Z (OPEN/CLOSE)
Opens or closes the disc tray.
j USB Port
Connect a USB device.
k PORT. IN
Connect to a portable player with audio
outputs.
l Microphone jacks 1/2
2010-03-10 ¿ÀÈÄ 4:01:54
12
Preparation
Rear panel
a
b
c
d
e
2
Preparation
a Power cord
b Speakers connectors
Connect the speaker cables.
c Cooling Fan
d Antenna Connector
FM- Connects the FM wired antenna
e VIDEO OUT
Connect to a TV with video inputs.
HT805SH-F2_BLKALL_ENG_6924.indd 12
ihg
f
f HDMI OUT (Version 1.2A)
Connect to TV with HDMI inputs.
(Interface for digital audio and video)
g OPTICAL IN
Connect to optical audio equipment.
h COMPONENT VIDEO (Y PB PR)OUTPUT
(PROGRESSIVE SCAN)
Connect to a TV with Y PB PR inputs.
i AUX (L/R) INPUT
Connect to an external source with 2
channel audio outputs.
2010-03-10 ¿ÀÈÄ 4:01:54
Installation
13
3
Installation
Attaching the
speakers to the unit
Speaker
Position
Grey
Rear
Rear right
Blue
Rear
Rear left
Green
Center
Center
Orange
Sub woofer
Any front position
Red
Front
Front right
White
Front
Front left
3
Installation
1. Connect the wires to the unit.
Match each wire’s colored band to the
same colored connection terminal on the
rear of the unit. To connect the cable to the
unit, press each plastic finger pad to open
the connection terminal. Insert the wire and
release the finger pad.
Color
To connect the cable to the speakers, press
each plastic finger pad to open the connection
terminals on the base of each speaker. Insert
the wire and release the finger pad.
CAUTION
Connect the black end of each wire to the
terminals marked -(minus) and the other
end to the terminals marked + (plus).
Be careful to make sure children not to put their
hands or any objects into the *speaker duct.
*Speaker duct: A hall for plentiful bass sound on
speaker cabinet (enclosure).
2. Connect the wires to the speakers.
Connect the other end of each wire to
the correct speaker according to the color
coding:
HT805SH-F2_BLKALL_ENG_6924.indd 13
2010-03-10 ¿ÀÈÄ 4:01:54
14
Installation
Positioning the
system
3
A Front left speaker (L)/
B Front right speaker (R):
Place the front speakers to the sides of the
monitor or screen and as flush with the screen
surface as possible.
The following illustration shows an example
of positioning the system. Note that the
illustrations in these instructions differ from the
actual unit for explanation purposes.
For the best possible surround sound, all the
speakers other than the subwoofer should be
placed at the same distance from the listening
position (A).
Installation
B
C
A
G
A
A
A
D
D Surround left speaker (L)/
E Surround right speaker (R):
Place these speakers behind your listening
position, facing slightly inwards.
F Subwoofer:
The position of the subwoofer is not so
critical, because low bass sounds are not
highly directional. But it is better to place
the subwoofer near the front speakers. Turn
it slightly toward the center of the room to
reduce the wall reflections.
G Unit
F
A
C Center speaker:
Place the center speaker above or below the
monitor or screen.
E
A
A ABCD E F G
HT805SH-F2_BLKALL_ENG_6924.indd 14
2010-03-10 ¿ÀÈÄ 4:01:54
Installation
Connections to Your
TV
Component Video Connection
Make one of the following connections,
depending on the capabilities of your existing
equipment.
You can hear the sound through the system’s
speakers.
15
Connect the COMPONENT VIDEO OUTPUT
(PROGRESSIVE SCAN) jacks on the unit to the
corresponding input jacks on the TV using
component cables.
Component Connection
NOTE
• Depending on your TV and other equipment
you wish to connect, there are various ways
you could connect the unit. Use only one of the
connections described in this manual.
Unit
3
Installation
• Please refer to the manuals of your TV, Stereo
System or other devices as necessary to make
the best connections.
• Make sure the unit is connected directly to
the TV. Tune the TV to the correct video input
channel.
• Do not connect your unit via your VCR. The
image could be distorted by the copy protection
system.
TV
Green
Blue
Red
HT805SH-F2_BLKALL_ENG_6924.indd 15
2010-03-10 ¿ÀÈÄ 4:01:55
16
Installation
HDMI Out Connection
If you have a HDMI TV or monitor, you can
connect it to this unit using a HDMI cable.
Connect the HDMI OUT jack on the unit to
the HDMI IN jack on a HDMI compatible TV or
monitor.
Set the TV’s source to HDMI (refer to TV’s
Owner’s manual).
HDMI Connection
NOTE
• If a connected HDMI device does not accept
the audio output of the unit, the HDMI device
’s audio sound may be distorted or may not
output.
• When you connect a HDMI or DVI compatible
device make sure of the following:
- Try switching off the HDMI/DVI device and this
unit. Next, switch on the HDMI/DVI device and
leave it for around 30 seconds, then switch on
this unit.
- The connected device’s video input is set
correctly for this unit.
3
Unit
Installation
- The connected device is compatible with
720x480i (or 576i), 720x480p (or 576p),
1280x720p,1920x1080i or 1920x1080p video
input.
• Not all HDCP-compatible HDMI or DVI devices
will work with this unit.
- The picture will not be displayed properly with
non-HDCP device.
TV
- This unit does not playback and TV screen is
changed to black or green screen or the snow
noise may occur on the screen.
• If there is noise or lines on the screen, please
check the HDMI cable and usea higher version
cable than 1.2A HDMI cable.
CAUTION
TIP
• You can fully enjoy digital audio and video
signals together with this HDMI connection.
• When you use HDMI connection, you can
change the resolution for the HDMI output.
(Refer to “Resolution Setting” on page 18.)
HT805SH-F2_BLKALL_ENG_6924.indd 16
• Changing the resolution when the connection
has already been established may result in
malfunctions. To solve the problem, turn off the
unit and then turn it on again.
• When the HDMI connection with HDCP is
not verified, TV screen is changed to black or
green screen or the snow noise may occur on
the screen. In this case, check the the HDMI
connection, or disconnect the HDMI cable.
2010-03-10 ¿ÀÈÄ 4:01:55
Installation
17
Video Connection
Connect the VIDEO OUT jack on the unit to the
video in jack on the TV using a video cable.
You can hear the sound through the
system’s speakers.
Video Connection
Unit
3
Installation
TV
Yellow
HT805SH-F2_BLKALL_ENG_6924.indd 17
2010-03-10 ¿ÀÈÄ 4:01:56
18
Installation
Resolution Setting
The unit provides several output resolutions for
HDMI OUT and COMPONENT VIDEO OUT jacks.
You can change the resolution using [Setup]
menu.
1. Press
HOME.
2. Use I/i to select the [Setup] and press 
ENTER. The [Setup] menu appears.
Video Output
Resolution
Displayed resolution in display window and
outputted resolution may different according
to connection type.
[HDMI OUT]: 1080p, 1080i, 720p and 480p (or
576p) and 480i (or 576i)
[COMPONENT VIDEO OUT]: 480p (or 576p) and
480i (or 576i)
3
Installation
[VIDEO OUT]: 480i (or 576i)
3. Use U/u to select [Display] option then
press i to move to the second level.
4. Use U/u to select the [Resolution] option
then press i to move to the third level.
5. Use U/u to select the desired resolution
then press  ENTER to confirm your
selection.
NOTE
If your TV does not accept the resolution you have
set on the player, you can set resolution to 480p (or
576p) as follows:
Press x (STOP) for more than 5 seconds.
HT805SH-F2_BLKALL_ENG_6924.indd 18
2010-03-10 ¿ÀÈÄ 4:01:56
Installation
Optional Equipment
Connection
19
AUDIO (PORT. IN) In
Connection
Connect an output of portable device (MP3
or PMP etc) to the AUDIO (PORT. IN) input
connector.
PORT.IN Connection
AUX In Connection
Connect an Output of auxiliary device to the
AUX (L/R) INPUT Connector.
AUX In Connection
3
MP3 player, etc...
Installation
Unit
Listening to music from your
portable player or external
device
The unit can be used to play the music from
many types of portable player or external
devices.
To the audio output jacks
of your component
(TV, VCR, etc.)
Red
White
1. Connect the portable player to the
PORT.IN(PORTABLE IN) connector of the
unit.
NOTE
If your TV has only one output for audio (mono),
connect it to the left (white) audio jack on the unit.
Or
Connect the external device to the AUX
connector of the unit.
2. Turn the power on by pressing 1 (POWER).
3. Select the PORTABLE or AUX (L/R) INPUT
function by pressing t RADIO&INPUT.
4. Turn on the portable player or external
device and start it playing.
HT805SH-F2_BLKALL_ENG_6924.indd 19
2010-03-10 ¿ÀÈÄ 4:01:56
20
Installation
USB Connection
Compatible USB Devices
Connect the USB port of USB Memory (or MP3
player, etc.) to the USB port on the front of the
unit.
• USB Flash Drive :Devices that support
USB2.0 or USB1.1.
USB Connection
• MP3 Player : Flash type MP3 player.
• The USB function of this unit does not
support some USB devices.
USB device requirement
• Devices which require additional program
installation connected to a computer, are
not supported.
• Do not extract the USB device while in
operation.
3
Installation
• For a large capacity USB, it may take longer
than a few minute to be searched.
• To prevent data loss, back up all data.
Removing the USB Device from the unit
1. Choose a different function mode or
press STOP (x) twice in a row.
2. Remove the USB device from the unit.
• If you use a USB extension cable or USB
hub, the USB device is not recognized.
• Using NTFS file system is not supported.
(Only FAT(16/32) file system is supported.)
• This unit is not supported when the total
number of files is 1 000 or more.
• External HDD, Card readers, Locked devices, or hard type usb devices are not supported.
• USB port of the unit cannot be connected
to PC. The unit can not be used as a storage
device.
HT805SH-F2_BLKALL_ENG_6924.indd 20
2010-03-10 ¿ÀÈÄ 4:01:56
Installation
OPTICAL In connection
21
Antenna Connection
Connect an optical output of Unit (or Digital
Device etc) to the OPTICAL IN connector.
OPTICAL IN Connection
Connect the supplied FM antenna for listening
to the radio.
Connect the FM Wire antenna to the FM
antenna connector.
Antenna Connection
3
Installation
To the digital
optical output jack
of your component
Home theater speaker ez setup
Listen to sound from TV, DVD and Digital
Device with 5.1(2.1 or 2)ch mode. Even in
power off mode, if you press OPTICAL, then
power is on and automatically changed to AUX
OPT mode.
1. Connect the unit’s OPTICAL IN jack to jack
on optical out of your TV (or Digital Device
etc.).
NOTE
Be sure to fully extend the FM wire antenna.
After connecting the FM wire antenna, keep it as
horizontal as possible.
2. Select the AUX OPT by using the OPTICAL.
To select the AUX OPT directly
3. Listen sound with 5.1(2.1 or 2)ch speaker.
4. To escape from AUX OPT by using the
OPTICAL.
Function is retuned to previous one.
HT805SH-F2_BLKALL_ENG_6924.indd 21
2010-03-10 ¿ÀÈÄ 4:01:57
22
Installation
Adjust the setup
settings
By using the Setup menu, you can make
various adjustments to items such as picture
and sound.
You can also set a language for the subtitles
and the Setup menu, among other things. For
details on each Setup menu item, see pages 22
to 26.
3
Installation
OSD Initial language settings
During the first use of this unit, the initial
language setup menu appears on your TV
screen. You must complete initial language
selection before using the unit. English will be
selected as the initial language.
1. Press 1 (POWER) to turn the unit on. The
language setup menu will appear on the
screen.
2. Use U u I i to select a language then
press  ENTER.
The confirm menu will appear.
To display and exit the Setup
menu
1. Press HOME.
Displays the [Home] Menu.
2. Select an [Setup] by using I i.
3. Press  ENTER.
Displays the [Setup]
4. Press HOME or O RETURN to exit in
the [Setup] Menu.
About help menu for Setup
Menu
Buttons
Operation
Uu
Moving to another
menu.
b
Move
I
Moving to previous
level.
B
Move
i
O
Close
O
RETURN
To exit the [Setup]
menu or [ 5.1
Speaker Setup].

Select
 ENTER
To confirm menu.
vV
Move
Moving to next level
or selecting menu.
3. Use I i to select the [Enter] then press 
ENTER to finish the language setup.
HT805SH-F2_BLKALL_ENG_6924.indd 22
2010-03-10 ¿ÀÈÄ 4:01:57
Installation
Language
Menu Language
Select a language for the Setup menu and
then on screen display.
Disc Audio / Disc Subtitle / Disc
Menu
Select the language you prefer for the audio
track (disc audio), subtitles, and the disc menu.
[Original]
Refers to the original language in which the
disc was recorded.
Display Mode
The Display Mode setting works only when the
TV Aspect mode is set to 4:3.
[Letterbox]
Displays a wide picture with bands on the
upper and lower portions of the screen.
[Panscan]
Automatically displays the wide picture
on the entire screen and cuts off the
portions that do not fit. (If the disc/file is not
compatible with Pan Scan, the picture is
displayed at Letterbox ratio.)
Resolution
Sets the output resolution of the Component
and HDMI video signal. Refer to “Resolution
Setting” for details about the resolution
(page 18).
Display
[Auto]
If the HDMI OUT jack is connected to
TVs providing display information (EDID),
automatically selects the resolution
best suited to the connected TV. If the
COMPONENT VIDEO OUT is only connected,
this changes the resolution to 480i (or 576i)
as default resolution.
TV Aspect
[1080p]
Outputs 1080 lines of progressive video.
[Off (for Disc Subtitle)]
Turn off Subtitle.
Select which screen aspect to use based on
the shape of your TV screen.
[4:3]
Select when a standard 4:3 TV is connected.
[16:9]
Select when a 16:9 wide TV is connected.
3
Installation
[Other]
To select another language, press numeric
buttons and then  ENTER to enter the
corresponding 4-digit number according
to the language code list on the page 38. If
you enter the wrong language code, press
CLEAR.
23
[1080i]
Outputs 1080 lines of interlaced video.
[720p]
Outputs 720 lines of progressive video.
[480p (or 576p)]
Outputs 480 (or 576) lines of progressive
video.
[480i (or 576i)]
Outputs 480 (or (576) lines of interlaced
video.
HT805SH-F2_BLKALL_ENG_6924.indd 23
2010-03-10 ¿ÀÈÄ 4:01:58
24
Installation
Audio
5.1 Speaker Setup
Make the following settings for the built-in 5.1
channel surround decoder.
1. Select [5.1 Speaker Setup] on the [Audio]
menu.
2. Press  ENTER.
The [5.1 Speaker setup] appears.
[Speaker selection]
Select a speaker that you want to adjust.
NOTE
Certain speaker settings are prohibited by the
Dolby Digital licensing agreement.
[Size]
Since the speaker settings are fixed, you
cannot change the settings.
[Volume]
Press I i to adjust the output level of the
selected speaker.
3
Installation
Front L/R : 0 ~ -5
SubWoofer, Rear L/R, Center : 5 ~ -5
3. Use I i to select the desired speaker.
4. Adjust options using U u I i buttons.
5. Returns to the previous menu by pressing
O RETURN.
[Distance]
After you connected speakers to your unit,
set the Distance between the speakers and
your listening point if the distance of Center
or Rear speakers is bigger than the distance
of Front speakers. This allows the sound
from each speaker to reach the listener
at the same time. Press I i to adjust the
Distance of the selected speaker. This
distance is equivalent to a difference of the
distance between Center or Rear speaker
and Front speakers.
[Test]
Select [Speaker Test Start] by using the U u
and press  ENTER. Press  ENTER again
to stop. Adjust the volume to match the
volume of test signals memorized in the
system.
DRC (Dynamic Range Control)
Make the sound clear when the volume is
turned down (Dolby Digital only). Set to [On]
for this effect.
HT805SH-F2_BLKALL_ENG_6924.indd 24
2010-03-10 ¿ÀÈÄ 4:01:58
Installation
Vocal
Select [On] to mix karaoke channels into
normal stereo.
This function is effective for multi-channel
karaoke DVDs only.
HD AV Sync
Lock (Parental Control)
Initial Setting of the Area Code:
When you use this unit for the first time, you
have to set the Area Code.
1. Select the [Lock] menu and then press i.
2. Press i.
To access the [Lock] options, you must
input the password you have created. Input
a password and press  ENTER. Enter it
again and press  ENTER to verify. If you
make a mistake before pressing  ENTER,
press CLEAR.
3. Select the first character using U u buttons.
Semi Karaoke
4. Press  ENTER and select the second
character using U u buttons.
When a chapter/ title/ track is fully finished, this
function shows the score in the screen with a
fanfare sound.
5. Press  ENTER to confirm your Area code
selection.
[On]
When you finished singing a score will
appear on the screen.
Rating
[Off]
Fanfare and score do not appears on the
screen.
1. Select [Rating] on the [Lock] menu then
press i.
NOTE
• DVD, DVD Karaoke discs with more than 2
tracks are available discs for the this function.
• When you watch movies, “off ” the Semi
Karaoke at the SETUP menu or enjoy it without
connecting the MIC if the fanfare or score
appears during changing a chapter.
• This function operate on the DVD/CD mode.
• The Semi Karaoke function is available only
when a microphone is connected.
HT805SH-F2_BLKALL_ENG_6924.indd 25
3
Installation
Sometimes Digital TV encounters a delay
between picture and sound. If this happens
you can compensate by setting a delay on the
sound so that it effectively ‘waits’ for the picture
to arrive: this is called HD AV Sync. Use U u
(on the remote control) to scroll up and down
through the delay amount, which you can set
at anything between 0 and 300m sec.
25
Blocks playback of rated DVDs based on their
contents. Not all discs are rated.
2. Input a password and press  ENTER.
3. Select a rating from 1 to 8 using the U u
buttons.
[Rating 1-8]
Rating one (1) has the most restrictions and
rating eight (8) is the least restrictive.
[Unlock]
If you select unlock, parental control is not
active and the disc plays in full.
4. Press  ENTER to confirm your rating
selection.
2010-03-10 ¿ÀÈÄ 4:01:58
26
Installation
Password
You can enter or change password.
1. Select [Password] on the [Lock] menu and
then press i.
2. Press  ENTER
3. Input a password and press  ENTER.
To change the password, press  ENTER
when the [Change] option is highlighted.
Input a password and press  ENTER. Enter
it again and press  ENTER to verify.
4. Press
HOME to exit the menu.
3
Installation
NOTE
If you forget your password, you can clear it using
the following steps:
Others
DivX VOD
We provide you with the DivX® VOD (Video On
Demand) registration code that allows you to
rent and purchase videos using the DivX® VOD
service.
For more information, visit www.divx.com/vod.
Press  ENTER when [DivX(R) VOD] is
highlighted and you can view the registration
code of the unit.
NOTE
All the downloaded videos from DivX VOD can
only be played back on this unit.
1. Select the [Setup] menu on the [Home] menu.
2. Input the 6-digit number “210499” and press
 ENTER. The password is cleared.
Area Code
Enter the code of the area whose standards
were used to rate the DVD video disc, based
on the list on page 39.
1. Select [Area Code] on the [Lock] menu then
press i.
2. Input a password and press  ENTER.
3. Select the first character using U u buttons.
4. Press  ENTER and select the second
character using U u buttons.
5. Press  ENTER to confirm your Area code
selection.
HT805SH-F2_BLKALL_ENG_6924.indd 26
2010-03-10 ¿ÀÈÄ 4:01:58
Operation
27
4
Operation
Using the Home Menu
Basic Operations
1. Press HOME.
Displays the [Home] menu.
1. Insert the disc by using the Z OPEN/
CLOSE or Connect the USB device to the
USB port.
2. Press HOME.
Displays the [Home] Menu.
3. Press  ENTER then selected option menu.
[Music] – Displays [MUSIC] menu.
3. Select an option by using I i.
If you select the [Movie], [Photo] or [Music]
option when you connect up to two
devices, it appears as belows. Select a
media then press  ENTER.
4
Operation
2. Select an option by using I i.
[Movie] – Start video media’s playback or
displays the [MOVIE] menu.
[Photo] – Displays [PHOTO] menu.
[Setup] – Displays the [Setup] menu.
NOTE
You can not select the [Music], [Movie] or [Photo]
option when the USB device is not connected or a
disc is not inserted.
HT805SH-F2_BLKALL_ENG_6924.indd 27
4. Press  ENTER then selected option menu.
NOTE
• For the most Audio CD and DVD-ROM discs,
playback starts automatically.
• The unit plays only music file contained in the
USB storage device or disc automatically.
2010-03-10 ¿ÀÈÄ 4:01:58
28
Operation
To
Stop
4
Press B (PLAY), MONO/
STEREO.
Pause
Press X (PAUSE/STEP).
Press X (PAUSE/STEP)
repeatedly to play title
Frame-by-Frame. (DVD, DivX
only)
Operation
During playback, press
./> SKIP to go to
Skipping to the next chapter/ track/
the next/
file or to return to the
previous
beginning of the current
chapter/ track/ chapter/ track/ file.
file
Press . SKIP twice
briefly to step back to the
previous chapter/ track/ file.
During playback, press
Locating a
m/M SCAN repeatedly
point quickly
to select the required scan
by playing
speed.
a file in fast
To return to normal speed,
forward or fast
press B (PLAY), MONO/
reverse
STEREO.
Playing
repeatedly or
randomly
Other Operations
Press x (STOP)
Playback
Frameby-Frame
playback
Do this
Press s REPEAT
repeatedly, and the current
title, chapter or track will be
played back repeatedly or
randomly.
- DVD : Chapter/ Title/ Off
- DivX : Title/ All/ Off
- Audio CD/ MP3/ WMA :
Track/ All/ Random/ Off
Displaying Disc Information
on-screen
You can display various information about the
disc loaded on-screen.
1. Press INFO/DISPLAY to show various
playback information.
The displayed items differ depending on
the disc type or playing status.
2. You can select an item by pressing U u and
change or select the setting by pressing
I i.
Title – Current title number/ total number of
titles.
Chapter – C
urrent chapter number/ total
number of chapters.
Time – Elapsed playing time.
Audio – Selected audio language or channel.
Subtitle – Selected subtitle.
Angle – S elected angle/ total number of
angles.
NOTE
If any button is not pressed for a few seconds, the
on-screen display disappears.
In the pause mode, press
SLOW (bb or BB) to
Slowing down
select the required speed.
the playing
(DVD, DivX only) The DivX
speed
file cannot be slow down
reverse playback.
HT805SH-F2_BLKALL_ENG_6924.indd 28
2010-03-10 ¿ÀÈÄ 4:01:58
Operation
To display the DVD Menu
DVD
When you play a DVD which contains several
menu, you can select the menu you want
using the Menu.
1. Press DISC MENU.
The disc’s menu appears.
DVD
When you play a DVD which contains several
title, you can select the title you want using the
Menu.
1. Press TITLE.
The disc’s title appears.
3. Press B (PLAY), MONO/STEREO to confirm.
3. Input the required start time in hours,
minutes, and seconds from left to right. If
you enter the wrong numbers, press CLEAR
to remove the numbers you entered. Then
input the correct numbers.
For example, to find a scene at 1 hour, 10
minutes, and 20 seconds, enter “11020” by
using numerical buttons.
4. Press  ENTER to confirm. Playback starts
from the selected time.
Resume playback
DVD
DVD
The 1.5 speed allows you to watch the pictures
and listen to the sound quicker than playing at
a normal speed.
1. During playback, press B (PLAY), MONO/
STEREO to play at 1.5 times speed. “BX1.5”
appears on the screen.
2. Press B (PLAY), MONO/STEREO again to
exit.
Screen Saver
The screen saver appears when you leave the
unit in Stop mode for about five minutes.
DivX
ACD
MP3
WMA
4
Operation
2. Select the menu by pressing U u I i.
HT805SH-F2_BLKALL_ENG_6924.indd 29
To start playing at any chosen time on the file
or title.
2. Press U u to select the time clock icon and
“--:--:--” appears.
3. Press B (PLAY), MONO/STEREO to confirm.
1.5 times speed playback
Starting play from selected
time DVD DivX
1. Press INFO/DISPLAY during playback.
2. Select the menu by using U u I i.
To display the DVD title
29
The unit records the point where you pressed
the x (STOP) depending on the disc.
If “Xx (Resume Stop)” appears on the screen
briefly, press B (PLAY), MONO/STEREO to
resume playback (from the scene point).
If you press x (STOP) twice or unload the disc,
“x”(Complete Stop) appears on the screen.
The unit will clear the stopped point.
NOTE
The resume point may be cleared when a button
is pressed (for example; 1 (POWER), Z OPEN/
CLOSE, etc).
2010-03-10 ¿ÀÈÄ 4:01:58
30
Operation
Marked Playback
ACD
MP3
NOTE
WMA
The mark function enables you to store your
favourite files from any disc or USB device in
the unit memory.
1. Select [Music] on the [Home] menu.
Music menu
Returning to the upper
folder. (MP3/ WMA only)
File information will be displayed
according to the ID3TAG
information on the appropriate
music file. (MP3 only)
If you want to select all files on the list, select
[Select All] and press  ENTER.
To delete a Marker
1. Use U u to select the track that you wish to
erase from the marked file.
2. Press MARKER.
To delete all Markers
Use U u I i to select [Deselect All] then press
 ENTER in program edit mode.
NOTE
4
Operation
The markers are also cleared when the disc or
USB device is removed, the unit is switched to
power off or the function is switched to others.
Selecting all tracks/ files.
Deselecting all tracks/files.
Moving to the previous or
next file list.
2. Select a desired music on the [List] by using
the U u then press MARKER to appears the
mark on the list.
3. Press  ENTER or B (PLAY), MONO/
STEREO.
Displays the play mode.
4. Select the play mode by using the U u and
press  ENTER.
Changing subtitle code page
DivX
If the subtitle is not displayed properly, you
can change the subtitle code page to view the
subtitle file properly.
1. During playback, press INFO/DISPLAY to
display the On-Screen display.
2. Use U u to select the [Code Page] option.
3. Use I i to select desired code option.
4. Press O RETURN to exit the On-Screen
display.
[Mark Play]
Marked playback.
[Current Play]
Normal playback
HT805SH-F2_BLKALL_ENG_6924.indd 30
2010-03-10 ¿ÀÈÄ 4:01:58
Operation
Viewing a PHOTO file
JPG
About help menu in the full screen.
This unit can play discs with photo files.
Menu
1. Select [Photo] on the [Home] menu and
press  ENTER.
Menu
Photo menu
Moving to the previous or
next file list.
31
Buttons
INFO/
DISPLAY
Operation
Displaying the
Option menu.
b/B
Prev./ Next
I/i
Moving to
another file
O Close
O
RETURN
Returning to
the [Photo]
menu.
Options while viewing a photo
You can use various options during viewing a
photo in full screen.
1. While viewing a photo in full screen, press
INFO/DISPLAY to display the option menu.
Returning to the upper
folder.
3. If you want to view a slide show, press U
u to highlight a file and press B (PLAY),
MONO/STEREO.
About help menu in the [Photo] menu.
Menu
Buttons
BSlide
Show
B (PLAY),
MONO/
STEREO
Operation
Viewing a slide
show.
vVbB
Move
UuIi
Moving to
another file or
content.
 Select
 ENTER
Viewing a
particular file.
O Close
O
RETURN
Returning to
the [Home]
menu.
HT805SH-F2_BLKALL_ENG_6924.indd 31
4
Operation
2. Press U u to select a folder, and then press
 ENTER.
2. Select an option using U u I i.
a
b
c
d e
a Current photo/ Total number of photos
– Use I i to view previous/next photo.
b Slide Show N/ X– Press  ENTER to
start or pause slide show.
c Speed x3/ x2/ x1 – Use  ENTER to
select a delaying speed between photos
in a slide show.
d Rotate – Press  ENTER to rotate the
photo.
e Go to list – Press  ENTER to return
[Photo] menu.
2010-03-10 ¿ÀÈÄ 4:01:58
32
Operation
Sleep Timer Setting
System Select - Optional
Press SLEEP one or more times to select delay
time between 10 and 180 minutes, after the
unit will turn off.
You must select the appropriate system mode
for your TV system. Press and hold X (PAUSE/
STEP) for more than five seconds to be able to
select a system in the [Home] menu. (PAL/ NTSC)
To check the remaining time, press SLEEP.
To cancel the sleep function, press SLEEP
repeatedly until “SLEEP 10” appears, and then
press SLEEP once again while “SLEEP 10” is
displayed.
NOTE
If the USB device is connected or a disc is inserted,
this function is not operated.
NOTE
You can check the remaining time before the
Unit turns off.
Press SLEEP The remaining time appears in the
display window..
Adjust the speaker level
settings
You can adjust the sound level of each speaker.
1. Press SPEAKER LEVEL repeatedly to select
a desired speaker to set.
4
Operation
Dimmer
Press SLEEP once. The display window will
be darken by half. To cancel it, press SLEEP
repeatedly until dim off.
2. Press VOL -/+ to adjust the sound level of
the selected speaker while the level setting
memu is displayed on the display window.
3. Repeat and adjust the sound level of the
other speakers.
Turn off the sound temporarily
Press
MUTE to mute your unit.
You can mute your unit in order, for example,
to answer the telephone, appears the MUTE in
the display window.
Last Scene Memory
DVD
This unit memorizes last scene from the last
disc that is viewed. The last scene remains in
memory even if you remove the disc from the
unit or switch off the unit. If you load a disc
that has the scene memorized, the scene is
automatically recalled.
VOCAL FADER
You can enjoy the function as karaoke, by
reducing singer vocal of music in the various
source. (MP3/ WMA/ CD/ etc.) Press the VOCAL
FADER, and “FADE ON” will appear in display
window.
To cancel it, press VOCAL FADER again.
The quality of the VOCAL FADER may be diff
erent depending on the recording conditions
of music files.
NOTE
• This function is available to use only when a
microphone is connected.
• It is not available on the MONO source.
HT805SH-F2_BLKALL_ENG_6924.indd 32
2010-03-10 ¿ÀÈÄ 4:01:59
Operation
Radio Operations
33
Presetting the Radio Stations
You can preset 50 stations for FM.
Be sure that both FM aerial is connected. (Refer
to the page 21)
Listening to the radio
1. Press t RADIO&INPUT until FM appears
in the display window.
The last received station is tuned in.
Before tuning, make sure that you have turned
down the volume.
1. Press t RADIO&INPUT until FM appears
in the display window.
2. Select the desired frequency by using
TUNING (-/+)
3. Press  ENTER a preset number will flash
in the display window.
2. Press and hold TUNING (-/+) for about
two seconds until the frequency indication
starts to change, then release. Scanning
stops when the unit tunes in a station.
4. Press PRESET (-/+) to select the preset
number you want.
or
6. Repeat the steps 2 to 5 to store other
stations.
4
Deleting all the saved stations
Operation
Press TUNING (-/+) repeatedly.
3. Adjust the volume by rotating VOLUME on
the front panel or by pressing VOL (+/- )on
the remote control repeatedly.
5. Press  ENTER.
The station is stored.
1. Press and hold CLEAR for two seconds.
"ERASE ALL" will flash up on the unit display.
2. Press CLEAR to erase all saved of the radio
stations.
Deleting a saved station
1. Press PRESET - / + to Select a preset
number you want to delete.
2. Press CLEAR, the preset number will blink
in the display window.
3. Press CLEAR again, to delete the selectd
preset number.
Improving poor FM reception
Press B (PLAY), MONO/STEREO on the
remote control. This will change the tuner
from stereo to mono and usually improve the
reception.
HT805SH-F2_BLKALL_ENG_6924.indd 33
2010-03-10 ¿ÀÈÄ 4:01:59
34
Operation
Sound adjustment
On Display
Description
MP3 OPT
This function is optimized
for compressible MP3, WMA
file. It improves the treble
sound.
Setting the surround mode
This system has a number of pre-set surround
sound fields. You can select a desired sound
mode by using SOUND EFFECT.
You can change the SOUND EFFECT using
I i arrow key while the sound effect
information is displayed on.
The displayed items for the equalizer maybe
different depending on sound sources and
effects.
On Display
4
Description
Operation
NAT PLUS
You can enjoy the natural
sound effect same as a
5.1-channel.
NATURAL
You can enjoy comfortable
and natural sound
BASS
LOUDNESS
VIRTUAL
PLII MOVIE
PLII MUSIC
BYPASS
During playback, reinforce
the treble, bass and
surround sound effect.
Improves the bass and
treble sound.
You can enjoy more virtual
surround sound.
Dolby Pro Logic II enables
you to play stereo source on
5.1-channel.
You can enjoy the sound
without equalizer effect.
NOTE
Regionally optimized
sound effect. (DANGDUT/
ARABIC/ PERSIAN/ INDIA/
REGUETON/ MERENGUE/
SAMBA/ SALSA/ CUMBIA/
AFRO)
• In some of surround modes, some speakers,
there's no sound or low sound. It depends on
the mode of surround and the source of audio,
it is not defective.
• This function is not operated when the
microphone is connected to the unit.
AUTO EQ
Realizes the sound equalizer
that is the most similar
to the genre of which is
included in the MP3 ID3 tag
of song files.
POP
CLASSIC
JAZZ
ROCK
This program lends an
enthusiastic atmosphere to
the sound, giving you the
feeling you are at an actual
rock pop, jazz or classic
concert.
Local
specialization
equalizer
HT805SH-F2_BLKALL_ENG_6924.indd 34
• You may need to reset the surround mode,
after switching the input, sometimes even
after the sound track changed.
2010-03-10 ¿ÀÈÄ 4:01:59
Operation
Advanced Operations
Recording to USB
You can record music or sound souce to USB
device by connecting in to the port on the
unit.
1. Connect the USB device to the unit.
2. Select a mode in which you want to record.
Play back a sound source first.
3. Start the recording by pressing z REC.
4. To stop recording, press x (STOP).
[All tracks/ files recording]
Record to USB in stop or play mode.
It'll be stored as follows
Audio CD
MP3/ WMA
The other
sources
(Tuner, AUX,
Portable)
HT805SH-F2_BLKALL_ENG_6924.indd 35
NOTE
• You can check the recording percentage rate
for the USB record on the screen during the
recording. (Audio CD or MP3/ WMA CD only)
• During recording MP3/WMA, there is no
sound.
• When you stop recording during playback, the
file that has been recorded at that time will be
stored. (Audio CD only)
• Do not remove the USB device or turn off
the unit during USB recording. If not, an
incomplete file may be made and not deleted
on PC.
• Recording through microphones is not
availabe.
• If USB recording does not work, the message
like “NO USB”, “ERROR”, “USB FULL” or “NO REC” is
displayed on the display window.
• Multi card reader device or external HDD can
not be used for USB recording.
• A file is recorded by 128 Mbyte (about 2 hours)
when you record for a long term. There are
recorded less than 4 files.
• When you stop recording during playback, the
file will not be stored.
4
Operation
[Program list recording]
After marking desired file(s) and you can
record it to USB (Refer to the page 30).
35
• In the state CD-G, DTS disc USB record is not
operated.
• The files in the sub-folders are not recorded
during all track recording.
• You may not record more than 999 files.
• The nunbering of the recording file is entered
from the lowest number. So if you delete some
of the recording files, the next recording file
could be the lowest number among them.
The making of unauthorized copies of copyprotected material, including computer
programs, files, broadcasts and sound recordings,
may be an infringement of copyrights and
constitute a criminal offense. This equipment
should not be used for such purposes.
Be responsible
Respect copyrights.
2010-03-10 ¿ÀÈÄ 4:01:59
36
Maintenance
5
Maintenance
Notes on Discs
Handling the Unit
Handling Discs
When shipping the unit
Please save the original shipping carton and
packing materials. If you need to ship the unit,
for maximum protection, re-pack the unit as it
was originally packed at the factory.
Never stick paper or tape on the disc.
Storing Discs
5
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of
heat and never leave it in a parked car exposed
to direct sunlight.
Maintenance
Cleaning Discs
Keeping the exterior surfaces clean
• Do not use volatile liquids such as
insecticide spray near the unit.
• Wiping with strong pressure may damage
the surface.
• Do not leave rubber or plastic products in
contact with the unit for a long period of
time.
Cleaning the unit
To clean the player, use a soft, dry cloth. If
the surfaces are extremely dirty, use a soft
cloth lightly moistened with a mild detergent
solution. Do not use strong solvents such as
alcohol, benzine, or thinner, as these might
damage the surface of the unit.
Do not use strong solvents such as alcohol,
benzine, thinner, commercially available
cleaners, or anti-static spray intended for older
vinyl records.
HT805SH-F2_BLKALL_ENG_6924.indd 36
Maintaining the Unit
The unit is a high-tech, precision device. If
the optical pick-up lens and disc drive parts
are dirty or worn, the picture quality could be
diminished. For details, please contact your
nearest authorized service center.
2010-03-10 ¿ÀÈÄ 4:01:59
Troubleshooting
37
6
Troubleshooting
PROBLEM
CAUSE
CORRECTION
Plug the power cord into the wall outlet
No power
The power cord is disconnected.
securely.
Select the appropriate video input mode
The TV is not set to receive the DVD signal. on the TV so the picture from the unit
appears on the TV screen.
No picture
The video cables are not connected
Connect the video cables securely to both
securely.
the TV and unit.
Equipment connected via the audio cable Select the correct input mode of the unit
is not set to receive DVD signal output.
so you can hear the sound from the unit.
There is little or The audio cables are not connected to the Connect the audio cables into the
no sound
speakers or unit securely.
connection terminals correctly.
The audio cables are damaged.
Replace with a new audio cable.
The DVD picture The disc is dirty.
quality is poor
No disc is inserted.
A DVD/CD will
not play
Radio stations
can’t be tuned in
properly
The remote
control doesn’t
work well / at all
Insert a disc.
Insert a playable disc (check the disc type,
An unplayable disc is inserted.
colour system and regional code).
Place the disc with the label or printed
The disc is inserted upside down.
side facing upwards.
There is a parental lock which prevents the Enter your password or change the rating
playback of DVDs with a certain rating.
level.
Clean the disc using a soft cloth with
The disc is dirty.
outward strokes.
The unit is located too close to the TV,
Move unit and audio components further
causing feedback.
away from your TV.
Check the antenna connection and adjust
The antenna is positioned or connected
its position.
poorly.
Attach an external aerial if necessary.
The signal strength of the radio station is
Tune to the station manually.
too weak.
No stations have been preset or preset
Preset some radio stations, see page 33 for
stations have been cleared (when tuning
details.
by scanning preset channels).
The remote is not pointed directly at the
Point the remote directly at the unit.
unit.
Use the remote within 23 feet (7m) of the
The remote is too far from the unit.
unit.
There is an obstacle in the path between
Remove the obstacle.
the remote control and the unit.
The battery in the remote control are flat. Replace the batteries with new ones.
HT805SH-F2_BLKALL_ENG_6924.indd 37
6
Troubleshooting
Humming noise
heard while a
DVD or CD is
playing
Clean the disc using a soft cloth with
outward strokes.
2010-03-10 ¿ÀÈÄ 4:01:59
38
Appendix
7
Appendix
Language Codes
Use this list to input your desired language for the following initial settings: Disc Audio, Disc
Subtitle, Disc Menu.
Appendix
7
Language Code
Language Code
Language Code
Language Code
Afar Afrikaans Albanian Ameharic Arabic Armenian Assamese Aymara Azerbaijani Bashkir Basque Bengali; Bangla Bhutani Bihari Breton Bulgarian Burmese Byelorussian Chinese Croatian Czech Danish Dutch English Esperanto Estonian Faroese Fiji Finnish 6565
6570
8381
6577
6582
7289
6583
6588
6590
6665
6985
6678
6890
6672
6682
6671
7789
6669
9072
7282
6783
6865
7876
6978
6979
6984
7079
7074
7073
French Frisian Galician Georgian German Greek Greenlandic Guarani Gujarati Hausa Hebrew Hindi Hungarian Icelandic Indonesian Interlingua Irish Italian Javanese Kannada Kashmiri Kazakh Kirghiz Korean Kurdish Laothian Latin Latvian, Lettish Lingala 7082
7089
7176
7565
6869
6976
7576
7178
7185
7265
7387
7273
7285
7383
7378
7365
7165
7384
7487
7578
7583
7575
7589
7579
7585
7679
7665
7686
7678
Lithuanian Macedonian Malagasy Malay Malayalam Maori Marathi Moldavian Mongolian Nauru
Nepali Norwegian Oriya Panjabi Pashto, Pushto Persian Polish Portuguese Quechua Rhaeto-Romance Rumanian Russian Samoan Sanskrit Scots Gaelic Serbian Serbo-Croatian Shona Sindhi 7684
7775
7771
7783
7776
7773
7782
7779
7778
7865
7869
7879
7982
8065
8083
7065
8076
8084
8185
8277
8279
8285
8377
8365
7168
8382
8372
8378
8368
Singhalese Slovak Slovenian Spanish Sudanese Swahili Swedish Tagalog Tajik Tamil Telugu Thai Tonga Turkish Turkmen Twi Ukrainian Urdu Uzbek Vietnamese Volapük Welsh Wolof Xhosa Yiddish Yoruba Zulu 8373
8375
8376
6983
8385
8387
8386
8476
8471
8465
8469
8472
8479
8482
8475
8487
8575
8582
8590
8673
8679
6789
8779
8872
7473
8979
9085
HT805SH-F2_BLKALL_ENG_6924.indd 38
2010-03-10 ¿ÀÈÄ 4:01:59
Appendix
39
Area Codes
Choose a area code from this list.
Code
AF
AR
AU
AT
BE
BT
BO
BR
KH
CA
CL
CN
CO
CG
CR
HR
CZ
DK
EC
EG
SV
ET
FJ
FI
FR
DE
GB
GR
Area Greenland Hong Kong Hungary India Indonesia Israel Italy Jamaica Japan Kenya Kuwait Libya Luxembourg Malaysia Maldives Mexico Monaco Mongolia Morocco Nepal Netherlands Netherlands Antilles New Zealand Nigeria Norway Oman Pakistan Panama Code
GL
HK
HU
IN
ID
IL
IT
JM
JP
KE
KW
LY
LU
MY
MV
MX
MC
MN
MA
NP
NL
AN
NZ
NG
NO
OM
PK
PA
Area Paraguay Philippines Poland Portugal Romania Russian Federation Saudi Arabia Senegal Singapore Slovak Republic Slovenia South Africa South Korea Spain Sri Lanka Sweden Switzerland Taiwan Thailand Turkey Uganda Ukraine United States Uruguay Uzbekistan Vietnam Zimbabwe Code
PY
PH
PL
PT
RO
RU
SA
SN
SG
SK
SI
ZA
KR
ES
LK
SE
CH
TW
TH
TR
UG
UA
US
UY
UZ
VN
ZW
Appendix
Area Afghanistan Argentina Australia Austria Belgium Bhutan Bolivia Brazil Cambodia Canada Chile China Colombia Congo Costa Rica Croatia Czech Republic Denmark Ecuador Egypt El Salvador Ethiopia Fiji Finland France Germany Great Britain Greece 7
HT805SH-F2_BLKALL_ENG_6924.indd 39
2010-03-10 ¿ÀÈÄ 4:01:59
40
Appendix
Trademarks and
Licenses
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol are
trademarks of Dolby Laboratories.
What is SIMPLINK?
Some functions of this unit are controlled
by TV’s remote control when this unit
and LG TV with SIMPLINK are connected
through HDMI connection. Controllable
functions by LG TV’s remote control; Play,
Pause, Scan, Skip, Stop, Power Off, etc.
• Refer to the TV owner’s manual for the
details of SIMPLINK function.
• LG TV with SIMPLINK function has the
logo as shown above.
• Use a higher version cable than 1.2 A
HDMI cable.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI licensing LLC.
“DVD Logo” is a trademark of DVD Format/Logo
Licensing Corporation.
Appendix
DivX is a registered trademark of DivX, Inc., and is
used under license.
7
HT805SH-F2_BLKALL_ENG_6924.indd 40
2010-03-10 ¿ÀÈÄ 4:02:00
Appendix
Specifications
General
• Power requirements:
Refer to main label
• Power consumption:
Refer to main label
• Dimensions (W x H x D):
360 x 62.5 x 312.3 mm without foot
• Net Weight (Approx.):
2.8 kg
41
Tuner
FM Tuning Range:
87.5 to 108.0 MHz or 87.50 to 108.00 MHz
Amplifier
• Stereo mode: 136 W + 136 W (4Ω at 1 kHz)
• Surround mode:
Front
136 W + 136 W (4Ω at 1 kHz)
Center
136 W (4Ω at 1 kHz)
Surround 136 W + 136 W (4Ω at 1 kHz)
Subwoofer 170 W (3Ω at 60 Hz)
• Operating temperature:
41 °F to 95 °F (5 °C to 35 °C)
• Operating humidity:
5 % to 90 %
• Bus Power supply (USB):
DC 5 V
500 mA
Inputs/ Outputs
• VIDEO OUT:
1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
• HDMI OUT (video/audio):
19 pin (HDMI standard, Type A)
HDMI version : 1.2A
Appendix
• COMPONENT VIDEO OUT:
(Y) 1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1,
(Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA jack x 2
• ANALOG AUDIO IN:
2.0 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R) x 1
• DIGITAL IN (OPTICAL 1):
3 V (p-p), Optical jack x 1
• PORT. IN:
0.5 Vrms (3.5 mm stereo jack)
HT805SH-F2_BLKALL_ENG_6924.indd 41
7
2010-03-10 ¿ÀÈÄ 4:02:00
42
Appendix
Speakers
• Front speaker
Type: Impedance : Rated Input Power:
Max. Input power: Net Dimensions
(W x H x D): Net Weight: • Rear speaker
Type: Impedance Rated Input Power:
Max. Input power: Net Dimensions
(W x H x D): Net Weight: • Center speaker
Type: Impedance: Rated Input Power:
Max. Input power: Net Dimensions
(W x H x D): Net Weight: Appendix
• Passive Subwoofer
Type: Impedance: Rated Input Power: Max. Input power: Net Dimensions
(W x H x D): Net Weight: 1 Way 1 speaker
4Ω
136 W
272 W
100x 186 x 100 mm
0.42 kg
1 Way 1 speaker
4Ω
136 W
272 W
100x 186 x 100 mm
0.47 kg
1 Way 1 speaker
4Ω
136 W
272 W
200 x 103 x 88 mm
0.43 kg
1 Way 1 speaker
3Ω
170 W
340 W
190 x 385 x 275 mm
4.55 kg
Designs and specifications are subject to change
without prior notice.
7
HT805SH-F2_BLKALL_ENG_6924.indd 42
2010-03-10 ¿ÀÈÄ 4:02:00
HT805SH-F2_BLKALL_ENG_6924.indd 43
2010-03-10 ¿ÀÈÄ 4:02:00
Download PDF