BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 1
ENGLISH
BD350
As an ENERGY STAR® Partner, LG
has determined that this product
or product models meet the
ENERGY STAR® guidelines for
energy efficiency.
ENERGY STAR® is a U.S. registered mark.
P/NO : MFL62745203
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
dangerous voltage within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC
SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
WARNING: Do not install this equipment in a confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer's
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing the
product on a bed, sofa, rug or other similar surface.
This product shall not be placed in a built-in installation such as a bookcase or rack unless
2
proper ventilation is provided or the manufacturer's
instruction has been adhered to.
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance, contact an authorized service centre.
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try
to open the enclosure. Visible laser radiation when
open. DO NOT STARE INTO BEAM.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
CAUTION concerning the Power Cord
Most appliances recommend they be placed
upon a dedicated circuit;
That is, a single outlet circuit which powers only that
appliance and has no additional outlets or branch
circuits. Check the specification page of this
owner's manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
centre. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point
where the cord exits the appliance. To disconnect
power from the mains, pull out the mains cord plug.
When installing the product, ensure that the plug is
easily accessible.
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 3
Notes on Copyrights
Licenses
Because AACS (Advanced Access Content
System) is approved as content protection system for BD format, similar to use of CSS (Content
Scramble System) for DVD format, certain
restrictions are imposed on playback, analog signal output, etc., of AACS protected contents. The
operation of this product and restrictions on this
product may vary depending on your time of purchase as those restrictions may be adopted
and/or changed by AACS after the production of
this product.
Furthermore, BD-ROM Mark and BD+ are additionally used as content protection systems for
BD format, which imposes certain restrictions
including playback restrictions for BD-ROM Mark
and/or BD+ protected contents. To obtain additional information on AACS, BD-ROM Mark, BD+,
or this product, please contact an authorized
Customer Service Centre.
Java and all Java-based trademarks and logos are
trademarks or registered trademarks of Sun
Microsystems, Inc. in the United States and other
countries.
Many BD-ROM/DVD discs are encoded with
copy protection. Because of this, you should only
connect your player directly to your TV, not to a
VCR. Connecting to a VCR results in a distorted
picture from copy-protected discs.
“DVD Logo” is a trademark of DVD Format/Logo
Licensing Corporation.
This product incorporates copyright protection
technology that is protected by U.S. patents and
other intellectual property rights. Use of this
copyright protection technology must be authorized by Macrovision, and is intended for home
and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.
“BONUSVIEW” is trademark of Blu-ray Disc
Association.
Under the U.S. Copyright laws and Copyright
laws of other countries, unauthorized recording,
use, display, distribution, or revision of television
programs, videotapes, BD-ROM discs, DVDs,
CDs and other materials may subject you to civil
and/or criminal liability.
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol are
trademarks of Dolby Laboratories.
Manufactured under license under U.S. Patent #:
5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,487,535 & other U.S. and worldwide patents
issued & pending. DTS is a registered trademark
and the DTS logos, Symbol, DTS-HD and DTS-HD
Advanced Digital Out are trademarks of DTS, Inc. ©
1996-2008 DTS, Inc. All Rights Reserved.
This product is licensed under the AVC patent portfolio license and VC-1 patent portfolio license for
the personal and non-commercial use of a consumer to (i) encode video in compliance with the
AVC Standard and VC-1 Standard (“AVC/VC-1
Video”) and/or (ii) decode AVC/VC-1 Video that was
encoded by a consumer engaged in a personal and
non-commercial activity and/or was obtained from a
video provider licensed to provide AVC/VC-1 Video.
No license is granted or shall be implied for any
other use. Additional information may be obtained
from MPEG LA, LLC. See http://www.mpegla.com.
“AVCHD” and the “AVCHD” logo are trademarks of
Panasonic Corporation and Sony Corporation.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI licensing LLC.
“x.v.Color” is a trademark of Sony Corporation.
“Blu-ray Disc” is a trademark.
3
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 4
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-8
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Connections to your TV . . . . . . . . . . . . . . . . . . . . . . . . . .12-13
Connecting to an Amplifier . . . . . . . . . . . . . . . . . . . . . . .13-14
The unit’s Audio Output Specifications . . . . . . . . . . . . . . . . .15
Resolution Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15-16
Using a USB Flash Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Using the Home Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Adjust the Setup settings . . . . . . . . . . . . . . . . . . . . . . . .18-22
Play a disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23-25
Displaying disc Information . . . . . . . . . . . . . . . . . . . . . . . . . .26
Playing a movie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Listening to music . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Viewing a photo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29-30
Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Language Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Area Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Before connecting, operating or adjusting this product,
please read this instruction booklet carefully and completely.
4
Open source software notice . . . . . . . . . . . . . . . . . . . . . . . .35
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 5
Introduction
To ensure proper use of this product, please read this owner’s manual
carefully and retain for future reference.
This manual provides information on the operation and maintenance of
your player. Should the unit require service, contact an authorized service
location.
About the
Symbol Display
“
“ may appear on your TV display during operation and indicates that
the function explained in this owner’s manual is not available on that specific media.
Symbols Used in this Manual
Note:
Indicates special notes and operating features.
Handling the Unit
When shipping the unit
Please save the original shipping carton and packing materials. If you need
to ship the unit, for maximum protection, re-pack the unit as it was
originally packed at the factory.
Keeping the exterior surfaces clean
Do not use volatile liquids such as insecticide spray near the unit.
Wiping with strong pressure may damage the surface.
Do not leave rubber or plastic products in contact with the unit for a long
period of time.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the surfaces are extremely dirty,
use a soft cloth lightly moistened with a mild detergent solution.
Do not use strong solvents such as alcohol, benzine, or thinner, as these
might damage the surface of the unit.
Tip:
Indicates tips and hints for making the task easier.
Maintaining the Unit
The unit is a high-tech, precision device. If the optical pick-up lens and disc
drive parts are dirty or worn, the picture quality could be diminished.
For details, please contact your nearest authorized service centre.
A section whose title has one of the following symbols are applicable only
to the disc represented by the symbol.
Notes on Discs
ALL
BD
All discs listed below
BD-ROM disc
DVD
DVD-Video, DVD±R/RW in Video mode or VR
mode and finalized
AVCHD
DVD±R/RW in AVCHD format
DivX
DivX files
ACD
Audio CDs
MP3
MP3 files
WMA
WMA files
Handling Discs
Do not touch the playback side of the disc. Hold the disc by the edges so
that fingerprints do not get on the surface. Never stick paper or tape on the
disc.
Storing Discs
After playing, store the disc in its case. Do not expose the disc to direct
sunlight or sources of heat and never leave it in a parked car exposed to
direct sunlight.
Cleaning Discs
Fingerprints and dust on the disc can cause poor picture quality and sound
distortion. Before playing, clean the disc with a clean cloth. Wipe the disc
from the centre out.
Do not use strong solvents such as alcohol, benzine, thinner, commercially
available cleaners, or anti-static spray intended for older vinyl records.
5
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 6
Playable Discs
Blu-ray Disc
- Discs such as movies that can be purchased or rented
- BD-R/RE discs that contain audio titles, DivX, MP3, WMA, or
Photo files.
DVD-VIDEO (8 cm / 12 cm disc)
Discs such as movies that can be purchased or rented
DVD-R (8 cm / 12 cm disc)
- Video mode and finalized only
- Supports the dual layer disc also
- AVCHD format
- DVD-R discs that contain audio titles, DivX, MP3, WMA, or
Photo files.
DVD-RW (8 cm / 12 cm disc)
- VR mode, Video mode and finalized only
- AVCHD format
- DVD-RW discs that contain audio titles, DivX, MP3, WMA, or
Photo files.
Notes:
Depending on the conditions of the recording equipment or the CDR/RW (or DVD±R/RW) disc itself, some CD-R/RW (or DVD±R/RW) discs
cannot be played on the unit.
Do not attach any seal or label to either side (the labeled side or the
recorded side) of a disc.
Do not use irregularly shaped CDs (e.g., heart-shaped or octagonal).
Doing so may result in malfunctions.
Depending on the recording software & the finalization, some recorded
discs (CD-R/RW or DVD±R/RW) may not be playable.
DVD±R/RW and CD-R/RW discs recorded using a personal computer or
a DVD or CD Recorder may not play if the disc is damaged or dirty, or if
there is dirt or condensation on the player’s lens.
If you record a disc using a personal computer, even if it is recorded in a
compatible format, there are cases in which it may not play because of
the settings of the application software used to create the disc. (Check
with the software publisher for more detailed information.)
This player requires discs and recordings to meet certain technical standards in order to achieve optimal playback quality. Pre-recorded DVDs
are automatically set to these standards. There are many different types
of recordable disc formats (including CD-R containing MP3 or WMA
files) and these require certain pre-existing conditions to ensure compatible playback.
Customers should note that permission is required in order to download
MP3 / WMA files and music from the Internet. Our company has no right
to grant such permission. Permission should always be sought from the
copyright owner.
DVD+R (8 cm / 12 cm disc)
- Finalized disc only
- Supports the dual layer disc also
- AVCHD format
- DVD+R discs that contain audio titles, DivX, MP3, WMA, or
Photo files.
DVD+RW (8 cm / 12 cm disc)
- Video mode and finalized only
- AVCHD format
- DVD+RW discs that contain audio titles, DivX, MP3, WMA, or
Photo files.
Audio CD (8 cm / 12 cm disc)
Audio CDs or CD-Rs/CD-RWs in audio CD format that can be
purchased
CD-R/CD-RW (8 cm / 12 cm disc)
CD-R/CD-RW discs that contain audio titles, DivX, MP3, WMA, or
Photo files.
6
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 7
BD-ROM Disc Features
BD-ROM Discs can store 25 GB (single layer) or 50 GB (dual layer) on a
single sided disc - about 5 to 10 times the capacity of a DVD.
BD-ROM Discs also support the highest quality HD video available in the
industry (up to 1920 x 1080) - Large capacity means no compromise on
video quality. Furthermore, a BD-ROM disc has the same familiar size and
look as DVD.
The following BD-ROM disc features are disc dependent and will vary.
Appearance and navigation of features will also vary from disc to disc.
Menu sounds
When you highlight or select a menu option, sounds can be heard such as
button clicks or a voice-over explaining the highlighted menu choice.
Multi-page/PopUp Menus
With DVD-Video, playback is interrupted each time a new menu screen is
accessed. Due to BD-ROM disc’s ability to preload data from the disc without interrupting playback, a menu can consist of several pages.
You can browse through the menu pages or select different menu paths,
while the audio and video remain playing in the background.
Not all discs will have the features described below.
Interactivity
Certain BD-ROM Discs may contain animated menus and/or trivia games.
BD-ROM, Hybrid disc have both BD-ROM and DVD (or CD) layers on
one side. On such discs, BD-ROM layer will be only played back in this
player.
User Browsable Slideshows
With BD-ROM Discs, you can browse through various still pictures while
the audio remains playing.
Video highlights
The BD-ROM format for movie distribution supports three highly advanced
video codecs, including MPEG-2, MPEG4 AVC (H.264), and SMPTE VC1.
HD video resolutions are also available:
1920 x 1080 HD
Subtitles
Depending on what is contained on the BD-ROM disc, you may be able to
select different font styles, sizes and colours for some subtitles. Subtitles
may also be animated, scrolled or faded in and out.
1280 x 720 HD
Graphic planes
Two individual, full HD resolution (1920x1080) graphic planes (layers) are
available, on top of the HD video layer. One plane is assigned to videorelated, frame accurate graphics (like subtitles), and the other plane is
assigned to interactive graphic elements, such as buttons or menus.
For both planes, various wipes, fades and scroll effects may be available.
BD-J Interactive Capability
The BD-ROM format supports Java for interactive functions. “BD-J” offers
content providers almost unlimited functionality when creating interactive
BD-ROM titles.
BD-ROM Disc Compatibility
This player supports BD-ROM Profile 1.1.
• Discs supporting BONUSVIEW (BD-ROM version 1.1 Profile 1 version
1.1/Final Standard Profile) that allows Virtual packages or Picture-inPicture functions to be used.
For High-Definition Playback
To view high-definition contents from BD-ROM discs, an HDTV is required.
Some discs may require HDMI OUT for viewing of high-definition contents.
Ability to view high-definition contents in BD-ROM discs may be limited
depending on the resolution of your TV.
7
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 8
Regional Code
Certain System Requirements
This unit has a regional code printed on the rear of the unit. This unit can
play only BD-ROM or DVD discs labeled same as the rear of the unit or
“ALL”.
For high definition video playback:
AVCHD (Advanced Video Codec High Definition)
• This player can playback AVCHD format discs. These discs are normally
recorded and used in camcorders.
• The AVCHD format is a high definition digital video camera format.
• The MPEG-4 AVC/H.264 format is capable of compressing images at
higher efficiency than that of the conventional image compressing
format.
• Some AVCHD discs use the “x.v.Colour” format.
• This player can playback AVCHD discs using “x.v.Colour” format.
• Some AVCHD format discs may not play, depending on the recording
condition.
• AVCHD format discs need to be finalized.
• “x.v.Colour” offers a wider colour range than normal DVD camcorder
discs.
Compatibility Notes
• Because BD-ROM is a new format, certain disc, digital connection and
other compatibility issues are possible. If you experience compatibility
problems, please contact an authorized Customer Service Centre.
• Viewing high-definition content and up-converting standard DVD content
may require a HDMI-capable input or HDCP-capable DVI input on your
display device.
• Some BD-ROM and DVD discs may restrict the use of some operation
commands or features.
• Dolby TrueHD, Dolby Digital Plus and DTS-HD are supported with maximum 7.1 channels if you use HDMI connection for the audio output of
the unit.
• You can use a USB Flash Drive that is used to store some disc related
information, including downloaded on-line content. The disc you are
using will control how long this information is retained.
8
• High definition display that has HDMI input jacks.
• BD-ROM disc with high definition content.
• HDMI or HDCP capable DVI input on your display device is required for
some content (as specified by disc authors).
• For up-conversion of standard definition DVD, a HDMI or HDCP capable
DVI input on your display device is required for copy protected content.
For Dolby® Digital Plus, Dolby TrueHD and DTS-HD multi-channel audio
playback:
• An amplifier/receiver with a built-in (Dolby Digital, Dolby Digital Plus,
Dolby TrueHD, DTS or DTS-HD) decoder.
• Main, center, surround speakers and subwoofer as necessary for chosen format.
Important Notice for TV colour system
The colour system of this player differs according to currently playing
discs.
For example, when the player plays back the disc recorded in the NTSC
colour system, the image is outputted as a NTSC signal.
Only the multi system colour TV can receive all signals outputted from the
player.
Notes:
• If you have a PAL colour system TV, you will see just distorted images
when using discs recorded in NTSC.
• The multi system colour TV changes the colour system automatically
according to input signals. In case that the colour system is not changed
automatically, turn it off and then on to see normal images on screen.
• If you try to record a NTSC output signal from the player with your
recorder, the recorder may not record the signal correctly.
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 9
Remote control
a
a SUBTITLE (
0-9 numerical buttons: Select numbered options in a
menu.
TITLE/POP-UP: Displays the DVD title menu or
BD-ROM’s popup menu, if available.
RESOLUTION: Sets the output resolution for HDMI
jacks.
OPEN/CLOSE (Z): Opens and closes the disc tray.
TV Control Buttons: See page 31.
CLEAR: Removes a mark on the search menu or a
number when setting the password.
b
b ): Selects a subtitle language.
d REPEAT: Repeat a desired section or sequence.
Remote Control Operation
Point the Remote Control at the remote sensor and
press the buttons.
N (PLAY): Starts playback.
x (STOP): Stops playback.
c SEARCH: Displays or exits the search menu.
ZOOM: Displays or exits the [Zoom] menu.
MARKER: Marks any point during playback.
. / > (SKIP): Go to next or previous chapter /
track / file.
Coloured (A, B, C, D) buttons: Use to navigate
BD-ROM menus. They are also used for [MOVIE],
[PHOTO] and [MUSIC] menu.
m / M (SCAN): Searches backward or forward.
X (PAUSE): Pauses playback.
c
SUBTITLE-ON/OFF: Switches the subtitle on or off.
POWER: Switches the player ON or OFF.
HOME: Displays or exits the [Home Menu].
Remote Control Battery Installation
Remove the battery cover on the rear of the Remote
Control, and insert a R03 (size AAA) battery with
and
matched correctly.
DISC MENU: Accesses menu on a disc.
d
RETURN (O): Exits the menu or resumes playback.
The resume play function may work depending on the
BD-ROM disc.
DISPLAY: Displays or exits On-Screen Display.
Direction buttons: Selects an option in the menu.
ENTER (
): Acknowledges menu selection.
AUDIO (
channel.
): Selects an audio language or audio
9
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 10
Front panel
a
a Disc Tray
Insert a disc here.
b OPEN/CLOSE (Z)
Opens or closes the disc tray.
c 1 (POWER) Button
Switches the unit ON or OFF.
d Display Window
Shows the current status of the player.
e Remote Sensor
Point the remote control here.
10
b
c
d
e
f
g
f N / X (PLAY / PAUSE)
Starts playback.
Pause playback temporarily,
press again to exit pause mode.
g x (STOP)
Stops playback.
h . / > (SKIP)
Go to next or previous file/track/chapter.
i USB Port
Connect a USB Flash Drive.
h
i
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 11
Rear panel
DIGITAL
AUDIO OUT
1080p
a
b
c
d
e
a AC Power Cord
Connect to a power source.
d 2CH AUDIO OUT (Left/Right)
Connect to a TV with 2 channel audio inputs.
b HDMI OUT (1080p)
Connect to TV with HDMI inputs. (Interface for digital audio and video)
e DIGITAL AUDIO OUT (COAXIAL)
Connect to digital (coaxial) audio equipment.
c VIDEO OUT
Connect to a TV with video inputs.
11
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 12
Connections to your TV
Make one of the following connections, depending on the capabilities of
your existing equipment.
Tips:
• Depending on your TV and other equipment you wish to connect, there
are various ways you could connect the player. Use only one of the connections described below.
• Please refer to the manuals of your TV, Stereo System or other devices
as necessary to make the best connections.
Cautions:
• Make sure the player is connected directly to the TV. Tune the TV to the
correct video input channel.
• Do not connect the player’s AUDIO OUT jack to the phono in jack
(record player) of your audio system.
• Do not connect your player via your VCR. The image could be distorted
by the copy protection system.
HDMI Connection
If you have a HDMI TV or monitor, you can connect it to this player using a
HDMI cable.
Connect the HDMI OUT jack on the player to the HDMI IN jack on a HDMI
compatible TV or monitor (H).
Set the TV’s source to HDMI (refer to TV’s Owner’s manual).
Note:
If a connected HDMI device does not accept the audio output of the unit,
the HDMI device’s audio sound may be distorted or may not output.
Tips:
• When you use HDMI connection, you can change the resolution for the
HDMI output. (Refer to “Resolution Setting” on page 15-16.)
• Select the type of video output from the HDMI OUT jack using
[HDMI Color Setting] option on the [Setup] menu (see page 19).
Cautions:
• Changing the resolution when the connection has already been established may result in malfunctions. To solve the problem, turn off the player and then turn it on again.
• When the HDMI connection with HDCP is not verified, TV screen is
changed to black screen. In this case, check the HDMI connection, or
disconnect the HDMI cable.
• If there is noise or lines on the screen, please check the HDMI cable
(length is generally limited to 15 ft.).
Additional Information for HDMI
TV
H
DIGITAL
AUDIO OUT
1080p
DIGITAL
AUDIO OUT
1080p
BD player
12
• When you connect a HDMI or DVI compatible device make sure of the
following:
- Try switching off the HDMI/DVI device and this player. Next, switch on
the HDMI/DVI device and leave it for around 30 seconds, then switch
on this player.
- The connected device’s video input is set correctly for this unit.
- The connected device is compatible with 720x576p, 1280x720p,
1920x1080i or 1920x1080p video input.
• Not all HDCP-compatible HDMI or DVI devices will work with this player.
- The picture will not be displayed properly with non-HDCP device.
- This player does not playback and TV screen is changed to black
screen.
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 13
Video/Audio (Left/Right) Connection
Connecting to an Amplifier
Connect the VIDEO OUT jack on the player to the video in jack on the TV
using a video cable (V).
Connect the left and right AUDIO OUT jacks of the player to the audio left
and right IN jacks on the TV using the audio cables (A).
Make one of the following connections, depending on the capabilities of
your existing equipment.
Note:
Since many factors affect the type of audio output, see “The unit’s Audio
Output Specifications” on page 15 for details.
Connecting to an Amplifier via 2 Channel Audio Output
TV
V
A
Connect the Left and Right 2CH AUDIO OUT jacks on the player to the
audio left and right in jacks on your amplifier, receiver, or stereo system,
using audio cables (A).
Connecting to an Amplifier via Digital Audio Output
(Coaxial)
Connect the player’s DIGITAL AUDIO OUT jack to the corresponding in
jack (COAXIAL X) on your amplifier. Use an optional digital (coaxial X)
audio cable. You will need to activate the player’s digital output. (See
“[AUDIO] Menu” on pages 20-21.)
BD player
BD player
A
X
Amplifier/Receiver
13
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 14
Connecting to an Amplifier via HDMI Output
Connect the player’s HDMI OUT jack to the corresponding in jack on your
amplifier. Use a HDMI cable (H1). You will need to activate the player’s
digital output. (See “[AUDIO] Menu” on pages 20-21.)
Notes:
• You must select a digital audio output and a maximum sampling
frequency that your Amplifier (or AV receiver) accepts using [SPDIF],
[HDMI] and [Sampling Freq.] options on the [Setup] menu
(see page 20-21).
• With digital audio connection (SPDIF or HDMI), Disc Menu button
sounds of BD-ROM may not be heard if the [SPDIF] or [HDMI] option is
set to [Primary Pass-Thru].
• If the audio format of the digital output does not match the capabilities of
your receiver, the receiver will produce a strong, distorted sound or no
sound at all.
BD player
• Multi-channel Digital Surround Sound via digital connection can only be
obtained if your receiver is equipped with a Digital Multi-channel
decoder.
H1
Amplifier/Receiver
TV
H2
Digital Multi-channel sound
A digital multi-channel connection provides the best sound quality. For this
you need a multi-channel Audio/Video Receiver that supports one or more
of the audio formats supported by your player. Check the receiver manual
and the logos on the front of the receiver. (PCM Stereo, PCM Multi-Ch,
Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS and/or DTS-HD)
Tip:
Connect the amplifier’s HDMI output jack to HDMI input jack on your TV
using a HDMI cable (H2) if your amplifier has HDMI output jack.
14
• To see the audio format of the current disc in the on-screen display,
press AUDIO.
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 15
The unit’s Audio Output Specifications
Jack/
Setting
Source
Analog Output
Stereo
SPDIF (DIGITAL AUDIO OUT) *5
PCM
Stereo
DTS
Re-encode *3 *6
Primary
Pass-Thru *1
Dolby Digital
PCM 2ch
PCM 2ch
DTS
Dolby Digital
Dolby Digital Plus
PCM 2ch
PCM 2ch
DTS
Dolby Digital
Dolby TrueHD
PCM 2ch
PCM 2ch
DTS
Dolby Digital
DTS
PCM 2ch
PCM 2ch
DTS
DTS
DTS-HD
PCM 2ch
PCM 2ch
DTS
DTS
Linear PCM 2ch
PCM 2ch
PCM 2ch
DTS
PCM 2ch
Linear PCM 5.1ch
PCM 2ch
PCM 2ch
DTS
PCM 2ch
Linear PCM 7.1ch
PCM 2ch
PCM 2ch
DTS
PCM 2ch
1
Jack/
Setting
Source
HDMI OUT
PCM
Stereo
PCM
Multi-Ch *3
DTS
Re-encode *6
Primary
Pass-Thru *1 *2
Dolby Digital
PCM 2ch
PCM 5.1ch
DTS
Dolby Digital
Dolby Digital Plus
PCM 2ch
PCM 7.1ch
DTS
Dolby Digital Plus
Dolby TrueHD
Dolby TrueHD
PCM 2ch
PCM 7.1ch
DTS
DTS
PCM 2ch
PCM 5.1ch
DTS
DTS
DTS-HD
PCM 2ch
PCM 7.1ch
DTS
DTS-HD
Linear PCM 2ch
PCM 2ch
PCM 2ch
DTS
PCM 2ch
Linear PCM 5.1ch
PCM 2ch
PCM 5.1ch
DTS
PCM 5.1ch
Linear PCM 7.1ch
PCM 2ch
PCM 7.1ch
DTS
PCM 7.1ch *4
1
Notes:
*1 The secondary and interactive audio may not be included in the output
bitstream if [SPDIF] or [HDMI] option is set to [Primary Pass-Thru].
(Except LPCM Codec : the output always include interactive and
secondary audio.)
*2 This player automatically selects the HDMI audio according to the
decoding capability of the connected HDMI device even though [HDMI]
option is set to [Primary Pass-Thru].
*3 The [PCM Multi-CH]/[Primary Pass-Thru] setting of the [HDMI] option
and [DTS re-encode] setting of the [SPDIF] option cannot be set
together. If you set the [HDMI] option to [PCM Multi-CH] or
[Primary Pass-Thru], the [SPDIF] option is set to [PCM Stereo]
automatically. Also, if you set the [SPDIF] option to [DTS Re-encode],
the [HDMI] option is set to [PCM Stereo] automatically.
*4 The LPCM audio recorded at 192kHz sampling frequency will be
outputted as stereo sound.
*5 On the PCM audio output, the sampling frequency of SPDIF (DIGITAL
AUDIO OUT) is limited to 96 kHz.
*6 If the [HDMI] or [SPDIF] option is set to [DTS re-encode], the audio
output is limited to 48 kHz and 5.1 ch. If the [HDMI] or [SPDIF] option
is set to [DTS re-encode], the DTS Re-encode audio is outputted for
BD-ROM discs, and the original audio is outputted for the other discs
(like [Primary Pass-Thru]).
• If [HDMI] option is set to [PCM Multi-CH] and [SPDIF] option is set to
[Primary Pass-Thru] when the unit plays back Dolby Digital Plus or
TrueHD audio, SPDIF (DIGITAL AUDIO OUT) jack is limited to “PCM
2ch”.
• If the HDMI connection is version 1.3 and Dolby Digital Plus/Dolby
TrueHD is outputted from HDMI OUT jack, SPDIF (DIGITAL AUDIO
OUT) jack is limited to “PCM 2ch” (When the HDMI and SPDIF are
connected simultaneously).
• The audio is outputted as PCM 48 kHz/16 bit for MP3/WMA file and
PCM 44.1kHz/16 bit for Audio CD while playback.
• The Dolby TrueHD audio recorded on some Blu-ray discs consists of
Dolby Digital and TrueHD audio. Dolby Digital audio is output through
DIGITAL AUDIO OUT jacks and "DD" displays on the screen if TrueHD
audio is not output (for example, when [HDMI] is set to [PCM Stereo]
and [SPDIF] is set to [Primary Pass-Thru]).
Resolution Setting
The player provides several output resolutions for HDMI OUT jacks.
You can change the resolution using [Setup] menu or pressing the
RESOLUTION button in stop mode.
15
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 16
Note:
• When the copy protected media is playing back
Since several factors affect the resolution of video output, see “Available
resolution according to the resolution setting”.
Resolution Setting
How to change the resolution using RESOLUTION
button
Press RESOLUTION repeatedly in stop mode to change the resolution.
The display window will show you the current resolution.
How to change the resolution using the [Setup] menu
1 Press HOME and the [Home Menu] appears.
2 Select the [Setup] and press ENTER. The [Setup] menu appears.
3 Use v / V to select [DISPLAY] option then press B to move to the
second level.
4 Use v / V to select the [Resolution] option then press B to move to the
third level.
5 Use v / V to select the desired resolution then press ENTER to confirm
your selection.
Video Output
HDMI OUT
576i
576p
576p
576p
720p
720p
1080i
1080i
1080p / 24Hz
1080p / 24Hz
1080p / 50Hz
1080p / 50Hz
Notes:
• Depending on your display, some of the resolution settings may result in
the picture disappearing or an abnormal picture appearing. In this case,
press HOME then RESOLUTION repeatedly until the picture re-appear.
• This player supports simultaneous output of all video out jacks.
HDMI OUT connection
Available resolution according to the resolution setting
• For the 576i resolution setting, real output resolution of HDMI OUT will
change to 576p.
• When the non-copy protected media is playing back
• If you select a resolution manually and then connect the HDMI jack to
TV and your TV does not accept it, the resolution setting is set to [Auto].
Video Output
HDMI OUT
Resolution Setting
16
576i
576p
576p
576p
720p
720p
1080i
1080i
1080p / 24Hz
1080p / 24Hz
1080p / 50Hz
1080p / 50Hz
• If you select a resolution that your TV does not accept, the warning
message will appear. After resolution change, if you cannot see the
screen, please wait 20 seconds and the resolution will automatically
revert back to the previous resolution.
• The 1080p video output frame rate may be automatically set to either
24Hz or 50Hz depending both on the capability and preference of the
connected TV and based on the native video frame rate of the content
on the BD-ROM disc.
VIDEO OUT connection
The resolution of the VIDEO OUT jack is always outputted at 576i
resolution.
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 17
Notes:
Using a USB Flash Drive
• This unit supports only USB Flash Drive with FAT16 or FAT32 format.
This unit can play the movie, music and photo
files contained on the USB Flash Drive.
ON REMOTE
1. Insert a USB Flash Drive to the USB port:
–
2 Displays the [Home Menu]:
HOME
3 Select a main option:
[Music], [Photo] or [Movie] option
b B, ENTER
4 Select the [USB] option:
bB
5 Displays corresponding menu list:
[MOVIE], [MUSIC] or [PHOTO] menu appears.
Details for the menu are on pages 27-30.
ENTER
• Do not extract the USB Flash Drive during operation (play, etc.).
• A USB Flash Drive which requires additional program installation when
you have connected it to a computer is not supported.
• USB Flash Drive: USB Flash Drive that support USB1.1 and USB2.0.
• Movie Files (DivX), Music files (MP3/WMA) and photo files (JPEG/PNG)
can be played. For details of operations on each file, refer to relevant
pages.
• Regular back up is recommended to prevent data loss.
• If you use a USB extension cable or USB HUB, the USB Flash Drive
may not be recognized.
Tip:
• Some USB Flash Drives may not work with this unit.
If you select the [Movie], [Photo] or [Music] option when a USB Flash Drive
is connected and a disc is inserted simultaneously, the menu for selecting
a media will appear. Select a media then press ENTER.
• Digital camera and mobile phone are not supported.
• USB Port of the unit cannot be connected to PC.
Insert/Remove a USB Flash Drive
Inserting a USB Flash Drive – Insert straight-in until it fits into place.
Removing a USB Flash Drive – Withdraw the USB Flash Drive
carefully.
BD player
USB Flash Drive
17
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 18
Using the Home Menu
Adjust the Setup settings
ON REMOTE
ON REMOTE
1 Displays the [Home Menu]:
HOME
1 Displays the [Home Menu]:
HOME
2 Select an option:
bB
2 Select the [Setup] option:
b B, ENTER
3 Displays the selected option menu:
ENTER
3 Select a desired option on the first level:
vV
4 Exit the [Home Menu]:
HOME
4 Move to second level:
B
5 Select a desired option on the second level:
vV
6 Move to third level:
B
7 Adjust or confirm the setting:
v V, ENTER
8 Go back to the previous level:
b
9 Exit the [Setup] menu:
HOME
[Movie] – Start video media’s playback or displays the [MOVIE] menu.
[Photo] – Displays [PHOTO] menu. (page 29-30)
[Music] – Displays [MUSIC ]menu. (page 28)
[Setup] – Displays the [Setup] menu. (page 18-22)
Tip:
If you select the [Movie], [Photo] or [Music] option when a USB Flash Drive
is connected and a disc is inserted simultaneously, the menu for
selecting a media will appear. Select a media then press ENTER.
Note:
The unit will be in stop mode then the [Home Menu] will appear if you
press HOME during playback.
First level
Second level
Third level
18
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 19
[DISPLAY] Menu
[1080p] – Outputs 1080 lines of progressive video.
[1080i] – Outputs 1080 lines of interlaced video.
[720p] – Outputs 720 lines of progressive video.
[576p] – Outputs 576 lines progressive video.
[576i] – Outputs 576 lines of interlaced video.
1080p Display Mode
When the resolution is set to 1080p, select [24Hz] for smooth presentation
of film material (1080/24p) with a HDMI-equipped display compatible with
1080/24p input.
TV Aspect Ratio
[4:3 Letter Box] – Select when a standard 4:3 TV is connected.
Displays theatrical images with masking bars above and below the
picture.
[4:3 Pan Scan] – Select when a standard 4:3 TV is connected.
Displays pictures cropped to fill your TV screen. Both sides of the
picture are cut off.
[16:9 Original] – Select when a 16:9 wide TV is connected.
The 4:3 picture is displayed with an original 4:3 aspect ratio, with black
bars appearing at the left and right sides.
[16:9 Wide] – Select when a 16:9 wide TV is connected.
The 4:3 picture is adjusted horizontally (in a linear proportion) to fill the
entire screen.
Note:
You cannot select [4:3 Letter Box] and [4:3 Pan Scan] option when the resolution is set to higher than 720p.
Resolution
Notes:
• When you select [24Hz], you may experience some picture disturbance
when the video switches video and film material. In this case, select
[50Hz].
• Even when [1080p Display Mode] is set to [24Hz], if your TV is not
compatible with 1080/24p, the actual frame frequency of the video
output will be 50Hz or 60Hz to match the video source format.
• When the 1080p/24Hz video source is outputted via HDMI connection,
the VIDEO OUT will not output any video signal.
HDMI Color Setting
Select the type of output from the HDMI OUT jack. For this setting, please
refer to the manuals of your display device.
[YCbCr] – Select when connecting to a HDMI display device.
[RGB] – Select when connecting to a RGB display device.
Note:
When you connect the HDMI OUT jack to DVI display device, the [HDMI
Color Setting] will automatically switch to [RGB].
Sets the output resolution of the HDMI video signal.
Refer to “Resolution Setting” on page 15-16 for details about the
resolution.
[Auto] – If the HDMI OUT jack is connected for TVs providing display
information (EDID), automatically selects the resolution best suited to
the connected TV.
19
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 20
[LANGUAGE] Menu
[AUDIO] Menu
Each disc has a variety of audio output options. Set the player’s Audio
options according to the type of audio system you use.
Note:
Since many factors affect the type of audio output, see “The unit’s Audio
Output Specifications” on page 15 for details.
Display Menu
Select a language for the [Setup] menu and on-screen display.
Disc Menu / Disc Audio / Disc Subtitle
Select the language you prefer for the audio track (disc audio), subtitles,
and the disc menu.
[Original] – Refers to the original language in which the disc was
recorded.
[Other] – Press ENTER to select another language. Use number buttons then ENTER to enter the corresponding 4-digit number according
to the language code list on page 32.
[Off] (for Disc Subtitle) – Turn off Subtitle.
Note:
Depending on the disc, your language setting may not work for some
discs.
HDMI / SPDIF (Digital Audio Output)
Select the output sound format when a device equipped with a HDMI or
Digital Audio input jack is connected to the HDMI OUT or DIGITAL AUDIO
OUT jack on this player.
[PCM Stereo] – Select if you connect this unit’s HDMI OUT or
DIGITAL AUDIO OUT jack to a device with two-channel digital stereo
decoder.
[PCM Multi-Ch] (HDMI only) – Select if you connect this unit’s
HDMI OUT jack to a device with multi-channel digital decoder.
[DTS Re-Encode] – Select if you connect this unit’s HDMI OUT or
DIGITAL AUDIO OUT jack to a device with DTS decoder.
[Primary Pass-Thru] – Select if you connect this unit’s DIGITAL
AUDIO OUT and HDMI OUT jack to a device with LPCM, Dolby
Digital, Dolby Digital Plus, Dolby TrueHD, DTS and DTS-HD decoder.
20
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 21
Note:
[LOCK] Menu (Parental Control)
When [HDMI] option is set to [PCM Multi-Ch], the audio may output as
PCM Stereo if the PCM Multi-Ch information is not detected from HDMI
device with EDID.
The [LOCK] settings affect only BD and DVD playback.
Sampling Freq.
[192KHz] – Select this if your A/V Receiver or Amplifier is capable of
handling 192 KHz signals.
[96KHz] – Select this if your A/V Receiver or Amplifier is NOT capable
of handling 192 KHz signals. When this choice is made, this unit automatically converts any 192 KHz signals to 96 KHz so your system can
decode them.
[48KHz] – Select this if your A/V Receiver or Amplifier is NOT capable
of handling 192 KHz and 96 KHz signal. When this choice is made,
this unit automatically converts any 192 KHz and 96 KHz signals to 48
KHz so your system can decode them.
Check the documentation for your A/V Receiver or Amplifier to verify its
capabilities.
DRC (Dynamic Range Control)
When a disc encoded in Dolby Digital or Dolby Digital Plus is playing back,
you may wish to compress the dynamic range of the audio output (the difference between the loudest sounds and the quietest ones). This allows
you to listen to a movie at a lower volume without losing clarity of sound.
Set DRC to [On] for this effect.
To access the any features in [LOCK] settings, you must enter the 4-digit
security code you have created.
If you have not entered a password yet, you are prompted to do so. Enter
a 4-digit password and press ENTER. Enter it again and press ENTER to
verify.
Password
You can create, change or delete the password.
[New] – Enter a 4-digit password and press ENTER. Enter it again and
press ENTER to create a new password.
[Change] – Enter the current password and press ENTER.
Enter a 4-digit password and press ENTER. Enter it again and press
ENTER to create a new password.
[Delete] – Enter the 4-digit password and press ENTER to delete the
password.
Tip:
If you make a mistake before pressing ENTER, press CLEAR. Then input
the correct password.
21
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 22
If you forget your password
Skin
If you forget your password, you can clear it using the following steps:
Changes the background of the initial screen.
1 Remove any disc that might be in the player.
2 Select [LOCK] option in the [Setup] menu.
3 Use Number buttons to enter “210499”. The password is cleared.
DVD Rating DVD
Blocks playback of rated disc based on their content. (Not all discs are
rated.)
[Rating 1-8] – Rating one (1) has the most restrictions and rating eight
(8) is the least restrictive.
[Unlock] – If you select unlock, parental control is not active and the
disc plays in full.
BD Rating
BD
Set an age limit of BD-ROM play. Use number buttons to input an age limit
for BD-ROM viewing.
Java Font Size
BD
You can adjust the default text size displayed for the BD-J contents during
BD-ROM playback.
This setting is only valid when BD-J contents do not set the size of text.
Please select a font size bigger than 24 when the player is connected with
a HD TV.
Initialize
You can reset the player to its original factory settings or initialize the BD
storage.
[Factory Set] – If you need to, you can reset the player to all its factory settings. Some options cannot be reset. (Rating, Password and Area
Code, etc.)
[BD Storage Clear] – Initializes the BD contents from the connected
USB Flash Drive.
[255] – All BD-ROM can be played.
[0-254] – Prohibits play of BD-ROM with corresponding ratings
recorded on them.
Area Code
Enter the code of the area whose standards were used to rate the DVD
video disc, based on the list on page 32.
[OTHERS] Menu
DivX Registration Code
DivX® is a digital video format created by DivX, Inc. This is an official DivX
Certified or DivX Ultra Certified device that plays DivX video.
This DivX® Certified device must be registered in order to play DivX Videoon-Demand (VOD) content. First generate the DivX VOD registration code
for your device and submit it during the registration process. [Important:
DivX VOD content is protected by a DivX DRM (Digital Rights
Management) system that restricts playback to registered DivX Certified
devices. If you try to play DivX VOD content not authorized for your device,
the message “Authorization Error” will be displayed and your content will
not play.] Learn more at www.divx.com/vod.
Press ENTER or B when [DivX Reg. Code] is highlighted and you can
view the registration code of the unit.
Note:
All the downloaded videos from DivX® VOD can only be played back on
this unit.
22
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 23
Resume playback
Play a disc
ON REMOTE
1 Open the disc tray:
Z)
OPEN/CLOSE (Z
2 Insert a disc:
-
3 Close the disc tray:
Z)
OPEN/CLOSE (Z
4 Adjust the disc menu settings:
A disc menu may not appear on the screen
depending on the disc.
v V b B, ENTER
5 Starts playback:
N)
PLAY (N
6 Stops playback:
x)
STOP (x
Notes:
•
•
When you turn on the player or replace a disc, the player returns to the
initial default setting. Depending on the disc, a specific type of audio
that the disc has is output.
Depending on the pre-recorded contents of the BD-ROM, some functions may not be available or may be operated differently than other
media.
If a disc menu screen is displayed
BD
DVD
AVCHD
DivX
The menu screen may be displayed first after loading a disc which contains a menu.
Use b / B / v / V buttons to select the title/chapter you want to view, then
press ENTER to start playback.
Skip to the next/previous chapter/track/file ALL
During playback, press . or > to go to the next chapter/track/file or
to return to the beginning of the current chapter/track/file.
Press . twice briefly to step back to the previous chapter/track/file.
BD
DVD
AVCHD
DivX
During playback, press STOP (x) to stop playback.
The unit records the stopped point, depending on the disc. “Xx” appears
on the screen briefly. Press PLAY (N) to resume playback (from the
scene point). If you press STOP (x) again or unload the disc (“x” appears
on the screen.), the unit will clear the stopped point. (Xx = Resume Stop,
x = Complete Stop)
Notes:
• The resume point may be cleared when a button is pressed
(for example; POWER, OPEN/CLOSE, etc).
• On BD-Video discs including BD-J, the resume play function does not
work.
• On BD-ROM interactive title, the unit will be in Complete Stop mode if
you press STOP once during playback.
Pause a playback ALL
During playback, press PAUSE (X) to pause playback. Press PLAY (N)
to continue playback.
Tip: During Audio CD or MP3/WMA playback, press X once again to
resume playback.
Frame-by-Frame playback
BD
DVD
AVCHD
DivX
Press PAUSE (X) repeatedly to play Frame-by-Frame playback.
Slow down the playing speed
BD
DVD
AVCHD
DivX
While the playback is paused, press SCAN M repeatedly to play in slow
motion (4 steps, forward only).
Fast forward or fast reverse ALL
Press SCAN (m or M) to play fast forward or fast reverse during
playback.
You can change the various playback speeds by pressing SCAN (m or
N) to continue play at normal speed.
M) repeatedly. Press PLAY (N
23
BD350-P.BSGPLLK_ENG
8/6/09
Playing repeatedly
BD
1:40 PM
DVD
Page 24
AVCHD
Using the search menu
ACD
During playback, press REPEAT repeatedly to select a desired repeat
mode. The current title, chapter or track will be played back repeatedly. To
return to normal playback, press REPEAT repeatedly to select [Off].
Note:
If you press > once during Repeat Chapter/Track playback, the repeat
playback cancels.
Repeating a specific portion (A-B)
BD
DVD
AVCHD
Enlarge the playback image
BD
DVD
AVCHD
DivX
During playback or pause mode, press ZOOM to display the [Zoom] menu.
Use b / B to select zoom mode (16 steps). Press RETURN to exit the
[Zoom] menu.
To return to the normal picture size, select [Off] on the [Zoom] menu.
Note:
This function may not work on some disc or titles.
Viewing the Title menu or Popup menu
BD
DVD
Press TITLE/POP-UP to displays the title menu or popup menu.
If the current DVD or BD-ROM disc has a menu, the Title menu or Popup
menu appears on the screen. Depending on the disc, the menu may not
be available.
24
DVD
AVCHD
DivX
Tip:
You can select a point that you want to skip by pressing and holding b / B
button.
Note:
This function may not work on some disc or titles.
Marker Search
ACD
Press REPEAT to select [A-] at the beginning of the portion you wish to
repeat and press ENTER at the end of the portion. Your selected portion will
be repeated continually. You cannot select a portion less than 3 seconds.
To return to normal playback, press REPEAT repeatedly to select [Off].
BD
During playback, press SEARCH to display the search menu.
Press b / B to skip the playback 15 seconds forward or backward.
BD
DVD
AVCHD
DivX
To enter a Marker
You can start playback from up to nine memorized points. To enter a marker, press MARKER at the desired point on the disc. The Marker icon
appears on the TV screen briefly. Repeat to enter up to nine markers.
To Recall or Clear a Marked Scene
Press SEARCH and the search menu appears on the screen.
Press a number button to select a marker number that you want to recall.
Playback starts from the marked scene.
OR
Press V to highlight a marker number. Use b / B to select a marked scene
that you want to recall or clear.
Press ENTER and playback starts from the marked scene. Press CLEAR
and the marked scene is erased from the search menu.
Notes:
• This function may not work on some disc or titles.
• All marked points are cleared if you press STOP (x) twice (complete
stop), the title is changed or if you unload the disc.
• If the total length of the title is less than 10 seconds, this function is not
available.
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Selecting a subtitle language
Page 25
BD
DVD
AVCHD
DivX
During playback, press SUBTITLE-ON/OFF to switch the subtitle on or off
and press SUBTITLE repeatedly to select a desired subtitle language.
OR
During playback, press DISPLAY to display the playback menu.
Use v V to select the [Subtitle] option then use b B to select desired
subtitle language.
Note:
Some discs allow you to change subtitle selections only via the disc menu.
If this is the case, press TITLE/POP-UP or DISC MENU button and choose
the appropriate subtitle from the selections on the disc menu.
Hearing a different audio
BD
DVD
AVCHD
DivX
During playback, press AUDIO repeatedly to hear a different audio
language, audio track or audio channel.
OR
During playback, press DISPLAY to display the playback menu.
Use v V to select the [Audio] option then use b B to select desired
audio language, audio track or audio channel.
Last Scene Memory
BD
DVD
This unit memorizes the last scene from the last disc that is viewed. The
last scene remains in memory even if you remove the disc from the unit or
switch off the unit. If you load a disc that has the scene memorized, the
scene is automatically recalled.
Notes:
• Settings are stored in memory for use any time.
• This unit does not memorize settings of a disc if you switch off the unit
before commencing to play it.
• Last Scene Memory function for a previous disc is erased once a
different disc is played.
• This function may not work depending on the disc.
Screen Saver
The screen saver appears when you leave the player in Stop mode for
about five minutes. If the Screen Saver is displayed for five minutes, the
unit automatically turns itself off.
Notes:
• Some discs allow you to change audio selections only via the disc
menu. If this is the case, press TITLE/POP-UP or DISC MENU button
and choose the appropriate audio from the selections on the disc menu.
• Immediately after you have switched sound, there may be a temporary
discrepancy between the display and actual sound.
• On BD-ROM disc, the multi audio format (5.1CH or 7.1CH) is displayed
with [MultiCH] in the on-screen display.
Using coloured (A, B, C, D) Buttons
BD
These buttons are available only during BD-J contents playback. Use the
appropriate buttons as indicated by the display. Depending on the disc
contents, the functions of each button may differ.
25
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 26
Moving to another title/chapter/track
Displaying disc information
BD
ON REMOTE
1 Play the disc loaded on the unit:
N)
PLAY (N
2 Displays the playback menu:
DISPLAY
3 Select an item:
vV
4 Adjust the playback menu settings:
bB
5 Exit the disc playback menu:
DISPLAY
DivX
Playing from selected time
BD
DVD
AVCHD
DivX
d
e
f
Watching from a different angle
Title/Track – Current title/track number/total number of titles/tracks.
Chapter – Current chapter number/total number of chapters.
Time – Elapsed playing time.
Audio – Selected audio language or channel.
Subtitle – Selected subtitle.
Angle – Selected angle/total number of angles.
Notes:
• If no button is pressed for a few seconds, the on-screen display
disappears.
• A title number cannot be selected on some discs.
• An item may not be available on some discs or titles.
• If BD interactive title is playing back, some setting information is
displayed on the screen but prohibited to be changed.
26
AVCHD
Press DISPLAY during playback. The time search box shows the elapsed
playing time. Select the [Time] option and then input the required start time
in hours, minutes, and seconds from left to right. For example, to find a
scene at 2 hours, 10 minutes, and 20 seconds, enter “21020” and press
ENTER. If you enter the wrong numbers, press CLEAR and enter the
correct numbers.
a
b
c
a
b
c
d
e
f
DVD
When a disc has more than one title/chapter/track, you can move to
another title/chapter/track.
Press DISPLAY during playback then use v / V to select the
[Title/Chapter/Track] icon. Then, press the appropriate numbered button
(0-9) or b / B to select a title/chapter/track number.
BD
DVD
If the disc contains scenes recorded at different camera angles, you can
change to a different camera angle during playback.
During playback, press DISPLAY to display the playback menu. Use v V
to select the [Angle] option, then use b B to select desired angle.
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 27
Movie file requirement (USB/DISC)
Playing a movie
Movie file compatibility with this player is limited as follows:
The player can play movie files on the disc/USB
device and video contents recorded on a
DVD-RW(VR mode) discs. Before playing movie
files, read “Movie file requirement”.
ON REMOTE
1 Inserts a disc/USB device containing
movie contents.
–
2 Displays the [Home Menu]:
HOME
3 Selects the [Movie] option:
b B, ENTER
4 Selects a movie from the [MOVIE] menu:
vV
5 Plays the selected movie:
N)
PLAY (N
6 Stops the playback:
x)
STOP (x
Notes:
• When the USB device is connected and a disc is inserted
simultaneously, the menu for selecting a media will appear.
Select a media then press ENTER.
• You can use various playback functions. Refer to pages 23-25.
• On the [MOVIE] menu, use red or blue button to move to the first or the
last file or track and green or yellow button to move to the previous or
next page.
• Unfinalized DVD VR format discs may not be played in this player.
• Some DVD-VR disc are made with CPRM data by DVD RECORDER.
This unit cannot support these kinds of discs.
Available resolution size: 720 x 576 (W x H) pixels
File extensions: “.avi”, “.mpg”, “.mpeg”
Playable subtitle: SubRip (.srt / .txt), SAMI (.smi),
SubStation Alpha (.ssa/.txt), MicroDVD (.sub/.txt), VobSub (.sub)
SubViewer 1.0 (.sub), SubViewer 2.0 (.sub/.txt), TMPlayer (.txt),
DVD Subtitle System (.txt)
Playable Codec format: “DIVX3.xx”, “DIVX4.xx”, “DIVX5.xx”, “XVID”,
“DIVX6.xx” (Standard playback only)
Playable Audio format: “Dolby Digital”, “DTS”, “MP3”, “WMA”, “AC3”
Sampling frequency: within 32-48 kHz (WMA), within 16-48 kHz (MP3)
Bit rate: within 20-320 kbps (WMA), within 32-320 kbps (MP3)
CD-R/RW, DVD±R/RW, BD-R/RE Format:
ISO 9660+JOLIET, UDF and UDF Bridge format
Maximum Files/Folder: Less than 2000
• The movie file name and subtitle are limited to 180 characters.
• Not all the WMA Audio format is compatible with this unit.
• This player does not support the file that are recorded with GMC*1 or
Qpel*2. Those are video encoding techniques in MPEG4 standard, like
DivX or XVID have.
*1 GMC – Global Motion Compensation
*2 Qpel – Quarter pixel
What is CPRM?
CPRM is a copy protection system (with scramble system) only allowing
the recording of ‘copy once’ broadcast programs. CPRM stands for
Content Protection for Recordable Media.
Notice for displaying the DivX subtitle
If the subtitle does not display properly, press and hold SUBTITLE for 3
seconds during playback. The language code will appear. Press SUBTITLE repeatedly to select another language code until the subtitle is displayed properly and then press ENTER.
27
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 28
Tips:
• To go directly to any track or file and play, enter the track/file number
using the numbered buttons (0-9).
Listening to music
The player can play Audio CDs and MP3/WMA
files. Before playing MP3/WMA files, read
“MP3/WMA audio file requirement”.
ON REMOTE
1 Inserts an Audio CD or a disc/USB Flash
Drive containing MP3/WMA files.
–
2 Displays the [Home Menu]:
HOME
3 Selects the [Music] option:
b B, ENTER
4 Selects a music from the [MUSIC] menu:
vVbB
5 Plays the selected music:
N)
PLAY (N
6 Stops the playback:
x)
STOP (x
• The playback may start automatically if the Audio CD inserted.
• Use v/V/b/B to select a folder then press ENTER and you can view the
files in the folder. If you want to move to the upper or lower
directory, use v/V to move to the desired directory.
• On the [MUSIC] menu, use red or blue button to move to the first or the
last file or track and green or yellow button to move to the previous or
next page.
• The equalizer indicator is not coupled with the music in play back.
• If there is impossible code to express in the file name, it may be
displayed as illegible.
MP3/WMA audio file requirement (USB/DISC)
File extensions: “.mp3”, “.wma”
Sampling frequency: within 8-48 kHz (WMA), within 11-48 kHz (MP3)
Bit rate: within 8-320 kbps (WMA, MP3)
CD-R/RW, DVD±R/RW, BD-R/RE Format:
ISO 9660+JOLIET, UDF and UDF Bridge format
Maximum Files/Folder: Less than 2000 (total number of files and
Example) MP3 files
Notes:
• When the USB Flash Drive is connected and a disc is inserted
simultaneously, the menu for selecting a media will appear. Select a
media then press ENTER.
• You can use various playback functions. Refer to pages 23-25.
28
folders)
Notes on MP3/WMA file
• Depending on the size and number of the MP3/WMA files, it may take
several minutes to read the contents of the media.
• This unit cannot support the ID3 Tag embedded in the MP3 file.
• The total playback time indicated on the screen may not correct for
VBR files.
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 29
Options during viewing a photo file in full screen
Viewing a photo
You can use various options during viewing a picture in full screen.
Use v V b B to select an option and use the options as described below.
This unit can play a photo files. Before playing
photo files, read “Photo file requirement” on page
30.
ON REMOTE
1 Inserts a disc/USB device containing
photo files.
–
2 Displays the [Home Menu]:
HOME
3 Selects a [Photo] option:
b B, ENTER
4 Selects a photo from the [PHOTO] menu:
vVbB
a
b
c
d
e
f
g
5 Displays the selected photo in full screen:
ENTER
a Use b B to advance to the previous or next file.
6 Displays the next or previous photo:
./>
b Press ENTER to start or pause the slide show.
7 Returns to the [PHOTO] menu screen:
x)
STOP (x
c Press ENTER to play or pause the background music. This option
is available after the background music is selected using
[Music Select] option.
d Selects the background music.
1) Press ENTER and the menu will appear.
2) Use v V b B to select a media or folder that there are music
file(s).
3) Press ENTER to confirm your selection.
Note:
When the USB Flash Drive is connected and a disc is inserted
simultaneously, the menu for selecting a media will appear. Select a media
then press ENTER.
e Press ENTER to rotate the picture clockwise.
This option is not available during slide show.
f Use v V to selects an option between [Effect] or [Delay].
Use b B to adjusts and press ENTER to set the selected option.
[Effects] – You can apply various effects when sliding photos.
OFF : Slide Show without any effect.
Fade In/Out : Fades a photo from inside to outside.
Slide : Slides a photo from up to down.
Mosaic : Transforms a photo into tiled pieces.
[Delay] – You can set the photo delaying time while Slide Show.
g Press ENTER to exit the option menu.
To appear the menu again, press ENTER.
29
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 30
Tips:
• To go directly to file and play, enter the file number using the
numbered buttons (0-9).
Photo file requirement (USB/DISC)
File extensions: “.jpg”, “.jpeg”, “.png”
•
You can advance to the previous or next file by pressing . or >
during viewing a photo file in full screen.
Recommended size:
Less than 3,000 x 3,000 x 24 bit/pixel
Less than 3,000 x 2,250 x 32 bit/pixel
•
You can start the slide show without option menu by pressing
PLAY (N) during viewing a photo file in full screen.
CD-R/RW, DVD±R/RW, BD-R/RE Format:
ISO 9660+JOLIET, UDF and UDF Bridge format
•
Use v V b B to select a folder then press ENTER and you can view
the files in the folder. If you want to move to the upper or lower directory, use v V to move to the desired directory.
folders)
•
If there is impossible code to express in the file name, it may be
displayed as illegible.
30
Maximum Files/Folder: Less than 2000 (total number of files and
Notes on Photo file
• Progressive and lossless compression photo image files are not
supported.
• Depending on the size and number of the photo files, it may take
several minutes to read the contents of the media.
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 31
Reference
Setting up the remote to control your TV
Controlling a TV with the Supplied Remote Control
You can operate your TV with the supplied remote control.
If your TV is listed in the table below, set the appropriate manufacturer
code.
You can control the volume, input source, and power state of your TV with
the supplied Remote Control.
You can control your TV using the buttons below.
TV
POWER
TV Control Buttons
While holding down TV POWER button, and press the manufacturer code
for your TV with the numerical buttons (see the table below).
Release the TV POWER button to complete setting.
Manufacturer
Code Number
LG / GoldStar
1 (Default), 2
Zenith
6, 7
Sony
8, 9
Hitachi
SCAN
PAUSE
SKIP
PLAY
STOP
By pressing
HOME
TV POWER
Turn the TV on or off.
AV/INPUT
Switch the TV’s input source between the
TV and other input sources.
PR/CH +/-
Scan up or down through memorized
channels.
VOL +/–
Adjust the volume of the TV.
TV MUTE
Temporarily turns TV sound OFF, press
again to restore.
1, 3, 4
Samsung
4
Depending on your TV, some or all buttons may not function on the TV,
even after entering the correct manufacturer code. When you replace the
batteries of the remote, the code number you have set may be reset to the
default setting. Set the appropriate code number again.
You can
Note:
Depending on the unit being connected, you may not be able to control
your TV using some of the buttons.
Resetting the unit
If you observe any of the following symptoms.
• The unit is plugged in, but the power will not turn on or off.
• The front panel display is not working.
• The unit is not operating normally.
You can reset the unit as follows.
• Press and hold the POWER button for at least five seconds. This will
force the unit to power off then turn the unit back on.
• Unplug the power cord, wait at least five seconds, and then plug it in
again.
31
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 32
Language Codes
Use this list to input your desired language for the following initial settings: [Disc Audio], [Disc Subtitle] and [Disc Menu].
Language
Afar
Afrikaans
Albanian
Ameharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali; Bangla
Bhutani
Bihari
Breton
Bulgarian
Burmese
Byelorussian
Chinese
Code
6565
6570
8381
6577
6582
7289
6583
6588
6590
6665
6985
6678
6890
6672
6682
6671
7789
6669
9072
Language
Croatian
Czech
Danish
Dutch
English
Esperanto
Estonian
Faroese
Fiji
Finnish
French
Frisian
Galician
Georgian
German
Greek
Greenlandic
Guarani
Gujarati
Code
7282
6783
6865
7876
6978
6979
6984
7079
7074
7073
7082
7089
7176
7565
6869
6976
7576
7178
7185
Language
Hausa
Hebrew
Hindi
Hungarian
Icelandic
Indonesian
Interlingua
Irish
Italian
Japanese
Kannada
Kashmiri
Kazakh
Kirghiz
Korean
Kurdish
Laothian
Latin
Latvian, Lettish
Code
7265
7387
7273
7285
7383
7378
7365
7165
7384
7465
7578
7583
7575
7589
7579
7585
7679
7665
7686
Language
Lingala
Lithuanian
Macedonian
Malagasy
Malay
Malayalam
Maori
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian
Oriya
Panjabi
Pashto, Pushto
Persian
Polish
Portuguese
Code
7678
7684
7775
7771
7783
7776
7773
7782
7779
7778
7865
7869
7879
7982
8065
8083
7065
8076
8084
Language
Quechua
Rhaeto-Romance
Rumanian
Russian
Samoan
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Shona
Sindhi
Singhalese
Slovak
Slovenian
Spanish
Sudanese
Swahili
Swedish
Tagalog
Code
8185
8277
8279
8285
8377
8365
7168
8382
8372
8378
8368
8373
8375
8376
6983
8385
8387
8386
8476
Language
Tajik
Tamil
Telugu
Thai
Tonga
Turkish
Turkmen
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Code
8471
8465
8469
8472
8479
8482
8475
8487
8575
8582
8590
8673
8679
6789
8779
8872
7473
8979
9085
Area Codes
Choose an area code from this list.
Area
Afghanistan
Argentina
Australia
Austria
Belgium
Bhutan
Bolivia
Brazil
Cambodia
Canada
Chile
China
Colombia
Congo
32
Code
AF
AR
AU
AT
BE
BT
BO
BR
KH
CA
CL
CN
CO
CG
Area
Costa Rica
Croatia
Czech Republic
Denmark
Ecuador
Egypt
El Salvador
Ethiopia
Fiji
Finland
France
Germany
Great Britain
Greece
Code
CR
HR
CZ
DK
EC
EG
SV
ET
FJ
FI
FR
DE
GB
GR
Area
Greenland
Hong Kong
Hungary
India
Indonesia
Israel
Italy
Jamaica
Japan
Kenya
Kuwait
Libya
Luxembourg
Malaysia
Code
GL
HK
HU
IN
ID
IL
IT
JM
JP
KE
KW
LY
LU
MY
Area
Maldives
Mexico
Monaco
Mongolia
Morocco
Nepal
Netherlands
Netherlands Antilles
New Zealand
Nigeria
Norway
Oman
Pakistan
Panama
Code
MV
MX
MC
MN
MA
NP
NL
AN
NZ
NG
NO
OM
PK
PA
Area
Paraguay
Philippines
Poland
Portugal
Romania
Russian Federation
Saudi Arabia
Senegal
Singapore
Slovak Republic
Slovenia
South Africa
South Korea
Spain
Code
PY
PH
PL
PT
RO
RU
SA
SN
SG
SK
SI
ZA
KR
ES
Area
Sri Lanka
Sweden
Switzerland
Taiwan
Thailand
Turkey
Uganda
Ukraine
United States
Uruguay
Uzbekistan
Vietnam
Zimbabwe
Code
LK
SE
CH
TW
TH
TR
UG
UA
US
UY
UZ
VN
ZW
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 33
Troubleshooting
Symptom
Possible Cause
Correction
No power.
• The power cord is disconnected.
• Plug the power cord into the wall outlet securely.
The power is on, but the
player does not work.
• No disc is inserted.
• Insert a disc.
No picture.
• The TV is not set to receive video signal output.
• Select the appropriate video input mode on the TV.
• The video cable is not connected securely.
• Connect the video cable securely.
• The selected resolution is not capable with your TV.
• Select another resolution using RESOLUTION button.
• The equipment connected with the audio cable is not
set to receive disc signal output.
• Select the correct input mode of the audio receiver so you
can listen to the sound from the player.
• The power of the equipment connected with the audio
cable is turned off.
• Turn on the equipment connected with the audio cable.
• The [AUDIO] options are set to the wrong position.
• Set the [AUDIO] options to the correct position
(see page 20).
• The player is in reverse play, fast forward, slow motion
or pause mode.
• Return to the normal playback.
• The disc is upside down.
• Insert the disc with the playback side down.
• An unplayable disc is inserted.
• Insert a playable disc. (Check the disc type and regional
code.)
• The rating level is set.
• Change the rating level.
• The disc was recorded on another unit and was not
finalized.
• Finalize the disc on that unit.
• The Remote Control is not pointed at the remote
sensor on the player.
• Point the Remote Control at the remote sensor of the
player.
• The Remote Control is too far from the player.
• Operate the Remote Control closer to the player.
No sound.
The player does not start
playback.
The Remote Control does
not work properly.
33
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 34
Specifications
General
System
Power requirements:
110-240V~ 50/60Hz
Power consumption:
23W
Laser:
Semiconductor laser,
wavelength: 405nm / 650 nm
Dimensions (W x H x D):
Approx. 430 x 35 x 200 mm without foot
Signal system:
Standard PAL/NTSC colour TV system
Net Weight (Approx.):
6 lbs (2.7 kg)
Frequency response:
Operating temperature:
41 °F to 95 °F 5 °C to 35 °C
20 Hz to 20 kHz
(48 kHz, 96 kHz, 192 kHz sampling)
Operating humidity:
5 % to 90 %
Signal-to-noise ratio:
More than 100 dB
(ANALOG OUT connectors only)
Outputs
Harmonic distortion:
Less than 0.008%
VIDEO OUT:
1.0 V (p-p), 75 Ω, sync negative,
RCA jack x 1
Dynamic range:
More than 95 dB
HDMI OUT (video/audio):
19 pin (HDMI standard, Type A)
Accessories
ANALOG AUDIO OUT:
2.0 Vrms (1 kHz, 0 dB), 600 Ω,
RCA jack (L, R) x 1
Remote control (1), Battery (1)
DIGITAL OUT (COAXIAL):
0.5 V (p-p), 75 Ω, RCA jack x 1
34
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 35
Open source software notice
The following GPL executables and LGPL libraries used in this product are
subject to the GPL2.0/LGPL2.1 License Agreements:
GPL EXECUTABLES: Linux kernel 2.6, bash, busybox, dhcpcd, mtd-utils,
net-tools, procps, sysutils, tinylogin
• libcurl library : Copyright © 1996 - 2008, Daniel Stenberg,
daniel@haxx.se
• boost C++ library : © Copyright Beman Dawes 1999-2003
• UPnP SDK : Copyright © 2000-2003 Intel Corporation
• Libnet : © 1998 - 2004 Mike D. Schiffman mike@infonexus.com
• Libpcap
This product includes other open source software.
LGPL LIBRARIES: uClibc, DirectFB, iconv, cairo, gnutls, libcrypt, libgpgerr, libusb
gSOAP Public License 1.3 LIBRARY: gsoap
LG Electronics offers to provide source code to you on CD-ROM for a
charge covering the cost of performing such distribution, such as the cost
of media, shipping and handling upon e-mail request to LG Electronics at:
opensource@lge.com
This offer is valid for a period of three(3) years from the date of the distribution of this product by LG Electronics.
You can obtain a copy of the GPL, LGPL licenses from
http://www.gnu.org/licenses/old-licenses/gpl-2.0.html and
http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html .
Also you can obtain a copy of gSOAP public license from
http://www.cs.fsu.edu/~engelen/license.html.
This software is based in part on the work of the Independent JPEG Group
copyright © 1991 - 1998, Thomas G. Lane.
This product includes
• Freetype library : copyright © 2003 The FreeType Project
(www.freetype.org).
• libpng library : copyright © 2004 Glenn Randers-Pehrson
• Zlib compression library: Copyright © 1995-2002 Jean-loup Gailly and
Mark Adler.
• Expat library : copyright © 2006 expat maintainers.
• OpenSSL library :
– cryptographic software written by Eric Young (eay@cryptsoft.com).
– software written by Tim Hudson (tjh@cryptsoft.com).
– software developed by the OpenSSL Project for use in the OpenSSL
Toolkit. (http://www.openssl.org)
•
•
•
•
•
•
•
•
•
Copyright © David L. Mills 1992-2006
Copyright © 1998-2003 Daniel Veillard.
Copyright © 1998, 1999 Thai Open Source Software Center Ltd.
Copyright © 1990 The Regents of the University of California.
Copyright © 1998-2005 The OpenSSL Project.
Copyright © 1991, 1992 Paul Kranenburg <pk@cs.few.eur.nl>
Copyright © 1993 Branko Lankester <branko@hacktic.nl>
Copyright © 1993 Ulrich Pegelow <pegelow@moorea.uni-muenster.de>
Copyright © 1995, 1996 Michael Elizabeth Chastain
<mec@duracef.shout.net>
• Copyright © 1993, 1994, 1995, 1996 Rick Sladkey <jrs@world.std.com>
• Copyright © 1999,2000 Wichert Akkerman <wakkerma@debian.org
All rights reserved.
Permission is hereby granted, free of charge, to any person obtaining a
copy of this software and associated documentation files (the "Software"),
to deal in the Software without restriction, including without limitation the
rights to use, copy, modify, merge, publish, distribute, sublicense, and/or
sell copies of the Software, and to permit persons to whom the Software is
furnished to do so, subject to the following conditions:
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF
ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO
THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,
DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS
IN THE SOFTWARE.
35
BD350-P.BSGPLLK_ENG
8/6/09
1:40 PM
Page 36
Download PDF

advertising