LG LZ-H100GBA5 Owner's manual

ENGLISH
ITALIANO
ESPAÑOL
FRANÇAIS
OWNER’S MANUAL
DEUTSCH
AIR
CONDITIONER
ΕΛΛΗΝΙΚΆ
ČEŠTINA
NEDERLANDS
Please read this manual carefully before operating
your set and retain it for future reference.
www.lg.com
P/NO : MFL67870424
Copyright © 2018 LG Electronics Inc. All Rights Reserved.
LIMBA ROMÂNĂ
[Representative] LG Electronics Inc. EU Representative : LG Electronics European Shared
Service Center B.V. Krijgsman 1, 1186 DM Amstelveen, The Netherlands
[Manufacturer] LG Electronics Inc. Changwon 2nd factory 84, Wanam-ro, Seongsangu, Changwon-si, Gyeongsangnam-do, KOREA
POLSKI
VENTILATOR
Original instruction
Ventilator owner’s manual
TABLE OF CONTENTS
Safety precautions.........................3
FOR YOUR RECORDS
Write the model and serial numbers here:
Model #
Prior to operation...........................7
Serial #
You can find them on a label on the side of each unit.
Dealer's name
Introduction ....................................8
Operating instructions
(Accessory) ..................................10
Characteristics .............................14
Maintenance and service ............15
Date purchased
n Staple your receipt to this page in the event you need
it to prove date of purchase or for warranty issues.
READ THIS MANUAL
Inside you will find many helpful hints on how to use
and maintain your ventilator properly. Just a little preventive care on your part can save you a great deal of
time and money over the life of your Ventilator.
You'll find many answers to common problems in the
chart of check item prior to notify a failure. If you review
our chart of
Check item prior to notify a failure, you may not
need to call for service at all.
Check Item prior to notify
a failure .........................................18
PRECAUTION
• Contact the authorized service technician for repair or maintenance of this unit.
• Contact the installer for installation of this unit.
• The ventilator is not intended for use by young
children or invalids without supervision.
• Young children should be supervised to ensure
that they do not play with the ventilator.
• When the power cord is to be replaced, replacement work shall be performed by authorized personnel only using only genuine replacement
parts.
• Installation work must be performed in accordance with the National Electric Code by qualified
and authorized personnel only.
2 Ventilator
Safety precautions
To prevent injury to the user or other people and property damage, the following instructions
must be followed.
Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is
classified by the following indications.
WARNING
This symbol indicates the possibility of death or serious injury.
CAUTION
This symbol indicates the possibility of injury or damage.
Meanings of symbols used in this manual are as shown below.
Be sure not to do.
Be sure to follow the instruction.
WARNING
Installation
Do not use a defective or underrated
circuit breaker. Use
this appliance on a
dedicated circuit.
• There is risk of fire or
electric shock.
Install the panel and
the cover of control
box securely.
• There is risk of fire or
electric shock.
For electrical work,
contact the dealer,
seller, a qualified
electrician, or an authorized service center.
• Do not disassemble or
repair the product.
There is risk of fire or
electric shock.
Always install a dedicated circuit and
breaker.
• Improper wiring or installation may cause
fire or electric shock
Always ground the
product.
• There is risk of fire or
electric shock.
Use the correctly
rated breaker or
fuse.
• There is risk of fire or
electric shock.
Owner's manual 3
ENGLISH
Safety precautions
Safety precautions
Do not modify or extend the power
cable.
• There is risk of fire or
electric shock.
For installation, always contact the
dealer or an authorized service center.
• There is risk of fire,
electric shock, explosion, or injury.
For re-installation of
the installed product,
always contact the
dealer or an authorized service center.
• There is risk of fire,
electric shock, explosion or injury.
Do not install, remove, or re-install
the unit by yourself
(customer).
• There is risk of fire,
electric shock, explosion, or injury.
• Sharp edges could
cause injury. Be especially careful of the
case edges and the
fins on the condenser
and evaporator.
Do not install the
product on a defective installation
stand.
Do not let the ventilator run for a long
time when the humidity is very high
and a door or a window is left open.
• It may cause injury, ac- • Moisture may concident, or damage to
dense and wet or damthe product.
age furniture.
Do not open the
maintenance cover
of the main body
during operation.
• Otherwise, it may
cause electrical shock.
Install the air intake
where polluted air
can not be directly
sucked in.
Install the product a
place that can support its weight.
• It may cause various
accidents, including
suffocation, due to the
suction of harmful
gasses(CO, etc.)
• Otherwise, it may
cause accident due to
falling of the product.
4 Ventilator
Be cautious when
unpacking and installing the product.
Use the outdoor air
suction hole with the
net installed to
ensure that birds
could not come in.
• Remove estrange
things like the bird’s
nest. Otherwise, it may
cause scarcity of indoor
oxygen.
Precautions must be
taken to avoid the
back-flow of gases into
the room from the open
flue of gas or other
fuel-burning appliances
Safety precautions
Take care to ensure
that power cable
could not be pulled
out or damaged during operation.
• There is risk of fire or
electric shock.
Do not place a
heater or other appliances near the
power cable.
• There is risk of fire and
electric shock.
Do not place anything on the power
cable.
• There is risk of fire or
electric shock.
• There is risk of fire or
electrical shock.
Do not allow water
to run into electric
parts.
Do not store or use
flammable gas or
combustibles near
the product.
• It may cause There is • There is risk of fire or
risk of fire, failure of the failure of product.
product, or electric
shock.
When flammable gas
leaks, turn off the
gas and open a window for ventilation
before turn the product on.
If strange sounds, or
small or smoke
comes from product.
Turn the breaker off
• Do not use the telephone or turn switches
on or off.
There is risk of explosion or fire
• There is risk of electric
shock or fire.
When the product is
soaked (flooded or
submerged), contact
an authorized service center.
• There is risk of fire or
electric shock.
Do not touch(operate) the product with
wet hands.
Be cautious that
water could not
enter the product.
• There is risk of fire,
electric shock, or product damage.
Don’t touch a dedicated circuit or
breaker with wet hands.
• There is risk of electric shock.
Stop operation and
close the window in
storm or hurricane.
If possible, remove
the product from the
window before the
hurricane arrives.
• There is risk of property
damage, failure of
product, or electric
shock.
Turn the breaker off
when cleaning or
maintaining the
product.
• There is risk of electric
shock.
Use a firm stool or ladder when
cleaning or maintaining the roduct.
• Be careful and avoid personal injury.
Owner's manual 5
ENGLISH
Operation
Safety precautions
CAUTION
Installation
Use two or more people to lift
and transport the product.
• Avoid personal injury.
Do not install the product where
it will be exposed to sea wind
(salt spray) directly.
• It may cause corrosion on the product. Corrosion, particularly on the
condenser and evaporator fins, could
cause product malfunction or inefficient operation.
Operation
Do not expose the
skin directly to cool
air for long periods
of time.
(Don't sit in the
draft.)
Do not use the prodUse a soft cloth to
uct for special purclean. Do not use
poses, such as
harsh detergents,
preserving foods,
solvents, etc.
works of art, etc. It is
a consumer ventilator,
not a precision refrigeration system.
• This could harm to your • There is risk of damage • There is risk of fire,
health.
or loss of property.
electric shock, or damage to the plastic parts
of the product.
Do not step on or put anyting on
the product. (outdoor units)
• There is risk of personal injury and
failure of product.
Use a firm stool or ladder when cleaning or maintaining the product.
• Be careful and avoid personal injury.
According to IEC 60335-1
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with
the appliance.
According to EN 60335-1
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the appliance in a safe way
and understnd the hazards involved. Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children without supervision.
6 Ventilator
Prior to operation
ENGLISH
Prior to operation
Preparing for operation
1. Contact an installation specialist for installation.
2. Plug in the power plug properly.
3. Use a dedicated circuit.
4. Do not use an extension cord.
5. Do not start/stop operation by plugging/unplugging the power cord.
6. If the cord/plug is damaged, replace it with only an authorized replacement part.
Usage
1. Being exposed to direct airflow for an extended period of time could be hazardous to
your health. Do not expose occupants, pets, or plants to direct airflow for extended
periods of time.
2. Due to the possibility of oxygen deficiency, ventilate the room when used together
with stoves or other heating devices.
3. Do not use this ventilator for non-specified special purposes (e.g. preserving precision devices, food, pets, plants, and art objects). Such usage could damage the
items.
Cleaning and maintenance
1. Do not touch the metal parts of the unit when removing the filter. Injuries can occur
when handling sharp metal edges.
2. Do not use water to clean inside the ventilator. Exposure to water can destroy the insulation, leading to possible electric shock.
3. When cleaning the unit, first make sure that the power and breaker are turned off.
The fan rotates at a very high speed during operation. There is a possibility of injury if
the unit’s power is accidentally triggered on while cleaning inner parts of the unit.
4. Ensure that the fan is switched off from the supply mains before removing the guard.
Service
For repair and maintenance, contact your authorized service dealer.
Owner's manual 7
Introduction
Introduction
Symbols used in this manual
This symbol alerts you to the risk of electric shock.
This symbol alerts you to hazards that could cause harm to the
ventilator.
NOTICE
This symbol indicates special notes.
Features
WARNING: This appliance should be installed in accordance with national wiring regulations. This guide acts as a guide to help to explain product features.
WARNING : Indoor unit ground wires are required for preventing electrical shock accident during current leakage, communication disorder by noise effect and motor current leakage (without connection to pipe).
Models: LZ-H025GBA4 / LZ-H035GBA5 / LZ-H050GBA5
5
1
6
2
3
7
4
8
1. Maintenance cover
2. Air filter
It prevents dust from clogging in total heat
exchanger.
3. Total heat exchanger
It changes temperature and humidity between supplying air and exhausted air.
4. Blower for exhaust air
It is a fan for discharging the contaminated
air to outdoor.
5. Control box
6. Blower for supply air
It is a fan for inhaling exterior air into an indoor space.
7. Damper plate(Board)
It converts exchanging mode between total
heat ventilation and general ventilation.
8. Total heat exchanger holder
It is used in guiding for the installation of total
heat exchanger.
h The figure of total heat exchanger can be different by the product model.
8 Ventilator
Introduction
ENGLISH
Models: LZ-H080GBA5 / LZ-H100GBA5
5
1
6
2
3
7
4
8
1. Maintenance cover
2. Air filter
It prevents dust from clogging in total heat
exchanger.
3. Total heat exchanger
It changes temperature and humidity between supplying air and exhausted air.
4. Blower for exhaust air
It is a fan for discharging the contaminated
air to outdoor.
5. Control box
6. Blower for supply air
It is a fan for inhaling exterior air into an indoor space.
7. Damper plate(Board)
It converts exchanging mode between total
heat ventilation and general ventilation.
8. Total heat exchanger holder
It is used in guiding for the installation of total
heat exchanger.
h The form of total heat exchanger varies according to models.
Models: LZ-H150GBA5 / LZ-H200GBA5
5
1
2
6
3
7
4
8
1. Maintenance cover
2. Air filter
It prevents dust from clogging in total heat
exchanger.
3. Total heat exchanger
It changes temperature and humidity between supplying air and exhausted air.
4. Blower for exhaust air
It is a fan for discharging the contaminated
air to outdoor.
5. Control box
6. Blower for supply air
It is a fan for inhaling exterior air into an indoor space.
7. Damper plate(board)
It converts exchanging mode between total
heat ventilation and general ventilation.
8. Total heat exchanger holder
It is used in guiding for the installation of total
heat exchanger.
h The form of total heat exchanger varies according to models.
Owner's manual 9
Operating instructions (Accessory)
Operating instructions (Accessory)
Name and function of remote controller
1
10
9
8
2
3
7
4
11
12
13
5
6
14
15
Model : PQRCVSL0
PQRCVSL0QW
Please attach the inform label inside of the door.
Please choose proper language depend on your
country.
1. OPERATION INDICATION SCREEN
2. SET TEMPERATURE BUTTON
3. FAN SPEED BUTTON
4. ON/OFF BUTTON
5. OPERATION MODE SELECTION BUTTON
6. WIRELESS REMOTE CONTROLLER RECEIVER
• Some products don't receive the wireless
signals.
7. AIR FLOW BUTTON
8. SUBFUNCTION BUTTON
9. FUNCTION SETTING BUTTON
10. VENTILATION BUTTON
11. RESERVATION
12. UP, DOWN, LEFT, RIGHT BUTTON
• To check the indoor temperature, press
button.
13. ROOM TEMPERATURE BUTTON
14. SETTING/CANCEL BUTTON
15. EXIT BUTTON
h Some functions may not be operated and
displayed depending on the product type.
Operation display
window
OK Button
Back button
On/Off Button
Up/Down/Left/Right
Button
Operation display window
Back button
Up/down/left/right button
OK button
On/Off button
Model: PREMTB100
Operation and Settings status display
When you move to the previous stage from the menu’s setting stage
When you change the menu’s setting value
When you save the menu’s setting value
When you turn ON/OFF the air conditioner
h Some functions may not be operated and displayed depending on the product type.
Refer to remote controller in order to know detail functions.
10 Ventilator
Operating instructions (Accessory)
It is used when air conditioner is interlinked with ventilation product.
It is a function that cools and refreshes indoor air using the ventilation product at the same time operating the air conditioning function.
Ventilation interlinked operation
button on the remote
1 Press
controller control panel.
- It is only used when air conditioner
and general ventilation is
interlinked.
'Start/Stop' button at ventilation
2 Pressing
mode will start ventilation.
button will change the
3 Pressing
ventilation operation mode.
Pressing operation selection button
will change the mode in the order of
'heat exchange → normal → automatic'
❈ It only displays on the remote controller
display when it is in ventilation mode, and it
displays the desired temperature when it
returns to air condition mode.
button in general
4 Pressing
ventilation mode will change airflow
speed.
Pressing airflow speed button will
change the mode in the order of 'weak →
strong → very strong'.
If CO2 sensor is installed, it can select from
'weak → strong → very strong → automatic'.
back to air conditioner mode
5 Changing
1)Automatic conversion : when no button is
pressed for 15 seconds or longer, it
automatically converts back to air
conditioner mode.
2) Manual conversion : pressing
button in
ventilation mode will manually convert.
Owner's manual 11
ENGLISH
Method to operate and select air volume – Interlinked operation with ventilation.
Operating instructions (Accessory)
Method to operate and select air volume – Ventilation single operation
It is a function to cool and refresh the indoor air using general ventilation product.
Ventilation single operation
button on the remote
1 Press
controller.
button will change
2 Pressing
the ventilation mode.
Ventilation Remote controller
Contents
mode
display
Heat
Circulate indoor air without loss of heat
exchange
Directly circulate indoor air without going
Normal
through heat exchanger
Circulate indoor air with automatically
Automatic
comparing indoor and outdoor air
In the case of heat exchange mode, the display is
shown as below.
→
→
→
→
→
→
→
button will change
3 Pressing
the strength of the wind
- Pressing the button can select
from 'weak → strong → very
strong'.
- If CO2 sensor is installed, it can select from
'weak → strong → very strong → automatic'.
12 Ventilator
Operating instructions (Accessory)
It is a function to operate ventilation function more efficiently through the ventilation additional functions, fast / power saving settings.
Fast : ventilates fast
button in ventilation mode.
1 Press
- It converts in the order of 'fast →
power saving' in ventilation mode.
is blinking on the display, and pressing
2 'Fast'button
will stabilize 'fast' icon, and the
function is set.
3 Pressing
settings.
button will exit the
Power saving : efficiently ventilates and performs
power savings.
button in ventilation mode.
1 Press
- It converts in the order of 'fast →
power saving' in ventilation mode.
saving' is blinking on the display, and
2 'Power
pressing
button will stabilize 'power
saving' icon, and the function is set.
3 Pressing
settings.
button will exit the
❈ General ventilation and direct expansion
ventilation have the same additional
functions.
❈ Ventilation/heater/humidifier additional
function settings are the same as air
conditioner.
Owner's manual 13
ENGLISH
Fast/energy saving ventilation mode
Characteristics
Characteristics
Ventilation via total heat exchanger
Exhausts indoor air via the total heat exchanger outdoor.
• The outdoor air heat exchanged is supplied to indoor. Operate the ventilator in the
ventilation via total heat exchanger in summer/winter when cool/heat operation is done.
Damper
Exhaust air
Return air
Outdoor air
Supply air
Total heat exchanger
Normal ventilation
Exhausts the polluted indoor-air directly without via the total heat exchanger.
• Operate the ventilator in the normal ventilation in spring/autumn when the total heat exchanger is
not required.
Damper
Exhaust air
Outdoor air
Return air
Supply air
Total heat exchanger
CAUTION: In case of high outdoor pollution degree like yellow sand please pause the
ventilator.
14 Ventilator
Maintenance and service
ENGLISH
Maintenance and service
Handling and cleaning
To prevent function of the ventilator deteriorating, clean dust adhered to the air filter and total heat
exchanger regularly.
Cleaning cycle
- Air filter: More than once every 6 months.
- Total heat exchanger: More than once every 2 years (Cleaning cycle may increase according to
pollution degree.)
Method to take each part out
CAUTION: Take care to ensure that you could not damage when taking the air filter out
since there is a sharp part on it.
WARNING: Turn the breaker off when cleaning the product.
CAUTION: Gloves should be worn when doing the maintenance work.
Model: LZ-H025GBA4 / LZ-H035GBA5 / LZ-H050GBA5
LZ-H080GBA5 / LZ-H100GBA5
1. Remove the maintenance cover.
Loosen a screw on the maintenance cover.
Put the hands inside of the ceiling from the maintenance cover, and pull the maintenance
cover up.
(Looser the hinge and detach the maintenance
cover.)
Main body
2. Take the air filter out.
Take the air filter with each contained to the
left/right downside of the total heat exchanger.
h If it adheres to the ceiling in reverse, it is equal
to the left/right topside of the total heat exchanger.
Main body
Air filter
3. Take the total heat exchanger out.
Catch the handle and then take the total heat
exchanger out from the main body. (2 units)
Handle
Main body
Owner's manual 15
Maintenance and service
Model: LZ-H150GBA5 / LZ-H200GBA5
1. Remove the maintenance cover.
Loosen a screw on the maintenance cover.
Put the hands inside of the ceiling from the maintenance cover, and pull the maintenance cover up.
(Looser the hinge and detach the maintenance cover.)
2. Take the air filter out.
Maintenance cover
Take the air filter with each contained to the
left/right downside of the total heat exchanger.
h If it adheres to the ceiling in reverse, it is
equal to the left/right topside of the total heat
exchanger.
Main body
3. Take the total heat exchanger out.
Catch the handle and then take the total heat
exchanger out from the main body. (4 units)
Main body
Method to clean and replace each part
1. Cleaning of air filter
Clean once every 6 months.
• Clean dirt from the air filter using a vacuum cleaner or
washing with water.
(If dirt is conspicuous, wash with a neutral detergent in
lukewarm water)
• After washing with water, dry well in the shade.
(Do not expose the air filter to direct sunlight or heat
from a fire when drying it)
• If the air filter is damaged, purchase it from the service
center or professional agent.
16 Ventilator
Air filter
Cleaner
Maintenance and service
ENGLISH
2. Cleaning of total heat exchanger
Suck dusts adhered to the surface of the total heat exchanger with a cleaner.
• Use the cleaner that attached to brush at its nozzle, and
use a soft brush.
• Do not use a hard nozzle on the cleaner.
(Otherwise, surface of the total heat exchanger may be
damaged.)
• Never wash the total heat exchanger with water.
• Replacement expenses are for a consideration after 2
years from the purchasing date.
• Expenses are for a consideration when you will contact
the service center even within 2 years from the purchasing date.
• For service, always contact the dealer or an authorized
service center.
Air filter
Total heat exchnger
Assembly and check after maintenance
WARNING: Turn the breaker off when cleaning the product.
CAUTION: Gloves should be worn when doing the maintenance work.
1. Assembly of total heat exchanger
Securely put the corner parts (4 parts) of the
total heat exchanger into the holder for assembly and slide them into the inside of the main
body.
Total heat
exchanger
Assemble the
air filter into the
holder structure.
Main body
Holder for
total heat exchanger
Owner's manual 17
Maintenance and service
2. Assembly of air filter
Assemble the air filter into the holder structure
of the total heat exchanger.
• Take care to ensure that surface of the total
heat exchanger could not be damaged.
• Dusts adhered to the total heat exchanger
may cause deterioration of air volume.
Main body
Air filter
3. Assembly of maintenance cover
Fix the cover to the right hinge and fix it to the
left side. (A nameplate is adhered toward the
reading direction).
Tighten a screw on the maintenance cover.
Hinge
Main body
Check item prior to notify a failure
Symptom
The product doesn't work
Check item
Is power not supplied?
Counter-measure
Supply power
Is the indoor temperature less
It's standby mode for protecting
than 15 ℃ (59 ℉) or more than
total heat exchanger.
40 ℃ (104 ℉)?
The product doesn't work through Is air filtecr, total heat
you press the 'On' switch
exchanger clogged severely?
Even though you change the
fan speed, the operation mode
doesn't change and it changes
to 'Auto or low'
Are the PCB and remote
controller rightly connected?
Connect rightly PCB and
remote controller.
Is the indoor temperature less
than -10 ℃ (14 ℉) or more than
45 ℃ (113 ℉)?
It's operation mode to protect
total heat exchanger.
Even though you push the
" displaying on
button of remote controller, any Is the icon "
remote controller?
function doesn't work.
18 Ventilator
Follow cleaning and changing
method.
It's child lock mode.
Refer to remote controller.