LG HT965TZ Owner’s Manual

OWNER’S MANUAL

DVD Receiver System

Please read this manual carefully before operating your set and retain it for future reference.

FOR THE WARRANTY TERMS & CONDITIONS,

PLEASE REFER TO BACK COVER OF THIS MANUAL.

MODEL

HT965TZ (HT965TZ, SH95TZ-S/ C/ W)

P/NO : MFL63284246

HT965TZ-DH_BGBRLL_ENG_4246.indd 1 2010-02-02 ¿ÀÈÄ 7:16:04

Safety Information

1

1

Safety Information

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK) NO USER-

SERVICEABLE PARTS INSIDE REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK

HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN

OR MOISTURE.

WARNING : Do not install this equipment in a confined space such as a book case or similar unit.

CAUTION : The apparatus shall not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, shall be placed on the apparatus.

CAUTION concerning the Power Cord

Most appliances recommend they be placed upon a dedicated circuit;

That is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner’s manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous.

Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized service center.

Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. To disconnect power from the mains, pull out the mains cord plug. When installing the product, ensure that the plug is easily accessible.

CAUTION : This product employs a Laser System.

To ensure proper use of this product, please read this owner’s manual carefully and retain it for future reference. Shall the unit require maintenance, contact an authorized service center.

Use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure.

To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM.


HT903 trans

Safety Information

Disposal of your old a ppliance

1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the

European Directive 2002/96/EC.

2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.

3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.

4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product.

LG Electronics hereby declares that this/ these product(s) is/are in compliance with the essential requirements and other relevant provisions of Directive

2004/108/EC, 2006/95/EC, and

2009/125/EC.

European representative :

LG Electronics Service Europe B.V.

Veluwezoom 15, 1327 AE Almere, The

Netherlands (Tel : +31–(0)36–547–8888)

WARNING : Do not install this equipment in a confined space such as a book case or similar unit.

CAUTION : Do not block any ventilation openings.

Install in accordance with the manufacturer's instructions.

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating.

The openings should be never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a builtin installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instruction have been adhered to.

1


Safety Information

1

This device is equipped with a portable battery or accumulator.

Safe way to remove the battery or the battery from the equipment:

Remove the old battery pack, follow the steps in reverse order than the assembly. To prevent contamination of the environment and bring on possible threat to human and animal health, the old battery or the battery put in the appropriate container at designated collection points. Do not dispose of batteries or battery together with other waste. It is recommended that you use local, free reimbursement system batteries and accumulators.

The battery shall not be exposed to excessive heat such as sunshine, fire or the like.

Copyrights

It is forbidden by law to copy, broadcast, show, broadcast via cable, play in public, or rent copyrighted material without permission. This product features the copy protection function developed by Macrovision. Copy protection signals are recorded on some discs. When recording and playing the pictures of these discs picture noise will appear. This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

CONSUMERS SHOULD NOTE THAT NOT ALL HIGH

DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE

WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS

TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525

OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS,

IT IS RECOMMENDED THAT THE USER SWITCH THE

CONNECTION TO THE ‘STANDARD DEFINITION

’ OUTPUT. IF THERE ARE QUESTIONS REGARDING

OUR TV SET COMPATIBILITY WITH THIS MODEL 525p

AND 625p UNIT, PLEASE CONTACT OUR CUSTOMER

SERVICE CENTER.

You have to set the disc format option to [Mastered] in order to make the discs compatible with the LG players when formatting rewritable discs. When setting the option to Live File System, you cannot use it on LG players.

(Mastered/ Live File System : Disc format system for

Windows Vista)


POWER: This unit operates on a mains supply of

200-240V~, 50/60Hz.

WIRING: This unit is supplied with a BSI 1363 approved

13 amp mains plug, fused at 5 amp. When replacing the fuse always use a 5 amp BS 1362, BSI or ASTA approved type. Never use this plug with the fuse cover omitted.

To obtain a replacement fuse cover contact your dealer.

If the type of plug supplied is not suitable for the mains sockets in your home, then the plug should be removed and a suitable type fitted. Please refer to the wiring instructions below:

WIRING: A mains plug removed from the mains lead of this unit must be destroyed. A mains plug with bared wires is hazardous if inserted in a mains socket. Do not connect either wire to the earth pin, marked with the letter E or with the earth symbol or coloured green or green and yellow. If any other plug is fitted, use a 5 amp fuse, either in the plug, or at the distribution board.

IMPORTANT: The wires in this mains lead are coloured in accordance with the following codes:

- BLUE: NEUTRAL, BROWN: LIVE As the colours of the wires in the mains lead of this unit may not correspond with the coloured marking identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

Safety Information

1


Contents

Contents

1

2

3

4

5

6

7

8

Safety Information

2 CAUTION

Preparation

11

13

14

8

8

9

9

9

9

9

10

Unique Features

Accessories

Introduction

Playable Discs

About the  Symbol Display

Symbol Used in this Manual

Regional Codes

Playable file Requirement

Remote control

Front panel

Rear panel

Installation

15

17

18

Assembling the speaker stand to the speaker

Mounting the speakers to a wall

Attaching the speakers to the unit

19 Positioning the system

20 Connections to Your TV

20

21

22

Component Video Connection

HDMI Out Connection

Video Connection

22

23

To connect to a TV with the

SCART jack

Resolution Setting

23 Video Output Resolution

24 Optional Equipment Connection

24

25

25

HDMI IN connection

AUX IN Connection

AUDIO (PORT. IN) In

Connection

25

26

27

Listening to music from your portable player or external device

USB Connection

OPTICAL In connection

27 Antenna Connection

29

29

30

31

32

28 Adjust the setup settings

28 OSD Initial language settings

28 To display and exit the Setup menu

Language

Display

Audio

Lock (Parental Control)

Others

Operation

33 Using the Home Menu

33 Basic Operations

34 Other Operations

34 Displaying Disc Information on-

35

35 screen

To display the DVD Menu

To display the DVD title


38

38

38

38

38

38

35

36

36

37

37

35

35

35

1.5 times speed playback

Screen Saver

Starting play from selected time

Resume playback

Marked Playback

Changing subtitle code page

Viewing a PHOTO file

Options while viewing a photo

Sleep Timer Setting

Dimmer

Turn off the sound temporarily

Last Scene Memory

System Select - Optional

Adjust the speaker level settings

39 Radio Operations

39 Presetting the Radio Stations

39

39

39

40

Deleting all the saved stations

Deleting a saved station

Improving poor FM reception

Seeing information about a radio station

41

41

Sound adjustment

Setting the surround mode

42 Advanced Operations

42 Recording to USB

43 Playing the iPod

44 Enjoying iPod on the screen

44 Enjoying the iPod IN mode

Maintenance

46 Notes on Discs

46 Handling the Unit

Troubleshooting

47 Handling the Unit

Appendix

48 Language Codes

49 Area Codes

50 Trademarks and Licenses

51 Specifications

Warranty

53 Warranty

Contents

1

2

3

4

5

6

7

8


Preparation

2

Preparation

2

Unique Features Accessories

Portable In

Listens to music from your portable device.

(MP3, Notebook, etc)

USB Direct Recording

Records music from CD to your USB device.

Full HD up-scaling

Views Full HD picture quality with simple setup.

Home Theater Speaker ez

Setup

listens sound form TV, DVD and Digital divce with vivid 5.1 (2.1 or 2.0) ch mode.

Please check and identify the supplied accessories.

RCA to SCART cable

(1)

Speaker cables (6)

Remote control (1) Batteries (2)

HDMI In

Simple connection with digital divice (Set Top

Box, DVD player etc.) through HDMI.

Made for iPod

Enjoys music form IPod with simple connection.

FM antenna (1)


Preparation

Introduction

Playable Discs

This unit plays DVD±R/RW and CD-R/RW that contains audio titles, DivX, MP3, WMA and/or

JPEG files. Some DVD±RW/DVD±R or CD-

RW/CD-R cannot be played on this unit due to the recording quality or physical condition of the disc, or the characteristics of the recording device and authoring software.

DVD-VIDEO (8 cm / 12 cm disc)

Discs such as movies that can be purchased or rented.

DVD±R (8 cm / 12 cm disc)

Video mode and finalized only

DVD-RW (8 cm / 12 cm disc)


DVD+R: Video mode only

Supports the double layer disc also

DVD+RW (8 cm / 12 cm disc)


Audio CD: Music CDs or CD-R/CD-

RW in music CD format that can be purchased.

About the



Symbol Display

“  ” may appear on your TV display during operation and indicates that the function explained in this owner’s manual is not available on that disc.

Symbol Used in this Manual

All discs and file listed below ALL

MP3 files

DVD and finalized DVD±R/RW

WMA files

DivX files

Audio CDs

JPG files

NOTE

Indicates special notes and operating features.

TIP

Indicates tip and hints for making the task easier.

CAUTION

Indicates cautions for preventing possible damages from abuse.

Regional Codes

This unit has a regional code printed on the rear of the unit. This unit can play only DVD discs labeled same as the rear of the unit or

“ALL”.

• Most DVD discs have a globe with one or more numbers in it clearly visible on the cover. This number must match your unit’s regional code or the disc cannot play.

• If you try to play a DVD with a different regional code from your unit, the message

“Check Regional Code” appears on the TV screen.

MP3

DVD

WMA

DivX

ACD

JPG

2


10 Preparation

2

Playable file

Requirement

MP3/ WMA music file requirement

MP3/ WMA file compatibility with this unit is limited as follows :

• Sampling frequency : within 32 to 48 kHz

(MP3), within 32 to 48 kHz (WMA)

• Bit rate : within 32 to 320 kbps (MP3),

40 to 192 kbps (WMA)

• Support Version : v2, v7, v8, v9

• Maximum files : Under 999

• File extensions : “.mp3”/ “.wma”

• CD-ROM file format : ISO9660/ JOLIET

• We recommend that you use Easy-CD

Creator, which creates an ISO 9660 file system.

Photo file requirement

Photo file compatibility with this unit is limited as follows :

• Max pixel in width : 2760 x 2048 pixel

• Maximum files : Under 999

• Some discs may not operate due to a different recording format or the condition of disc.

• File extensions: “.jpg”

• CD-ROM file format : ISO9660/ JOLIET

DivX file requirement

DivX file compatibility with this unit is limited as follows :

• Available resolution: within 720x576 (W x H) pixels.

• The file name of the DivX subtitle should be entered within 45 characters.

• If there is impossible code to express in the

DivX file, it may be displayed as " _ " mark on the display.

• Frame rate : less than 30 fps.

• If the video and audio structure of recorded files is not interleaved, either video or audio is outputted.

• Playable DivX file : ".avi", ".mpg", ".mpeg",

".divx"

• Playable Subtitle format : SubRip (*.srt/

*.txt), SAMI (*.smi), SubStation Alpha (*.ssa/

*.txt), MicroDVD (*.sub/ *.txt), SubViewer 2.0

(*.sub/ *.txt), Vobsub (*.sub)

• Playable Codec format : "DIVX3.xx", "DIVX4.

xx", "DIVX5.xx", "MP4V3", "3IVX".

• Playable Audio format : "AC3", "DTS", "PCM",

"MP3", "WMA".

• Sampling frequency : within 32 to 48 kHz

(MP3), within 32 to 48 kHz (WMA)

• Bit rate : within 32 to 320 kbps (MP3), 40 to

192 kbps (WMA)

• For Discs formatted in Live file system, you can not it on this unit.

• If the name of movie file is different from that of the subtitle file, during playback of a

DivX file, subtitle may not be display.

• If you play a DivX file differ from DivXspec, it may not operate normally.


Remote control

Remote control a b

OPEN /

CLOSE

RADIO &

INPUT c d

CLEAR

SKIP SCAN

MONO/STEREO

REPEAT

SKIP

SPEAKER

LEVEL

SOUND

EFFECT

VOL

OPTICAL

MUTE e f g

PRESET

ENTER

PRESET

RETURN

TITLE

DISC MENU

MARKER SLEEP REC

AV / INPUT

VOL

VOL

PR/CH

PR/CH

Preparation 11 t RADIO&INPUT : Changes input sources.

• • • • • • • • • • b

• • • • • • • • •

0 to 9 numerical buttons : Selects numbered options in a menu.

CLEAR : Removes a number when setting the password.

s REPEAT : Selects a play mode. (Repeat/

Random)

• • • • • • • • • • c • • • • • • • • •

./> SKIP : Goes to next or previous chapter/ track/ file. m / M SCAN : Searchs backward or forward. x (STOP) : Stops playback or recording.

B (PLAY) , MONO/STEREO : Starts playback.

Selects Mono/ Stereo.

X (PAUSE/STEP) : Pauses playback.

• • • • • • • • • • d

• • • • • • • • •

SPEAKER LEVEL : Sets the sound level of desired speaker.

SOUND EFFECT : Selects a sound effect mode.

VOL -/+(Volume) : Adjusts speaker volume.

OPTICAL : Changes input source to optical directly.

MUTE : Mutes the sound.

Put the batteries into the remote control.

Make sure for the + (plus) and – (minus) on the batterise to be matched on the remote control.

2

• • • • • • • • • • a • • • • • • • • •

1 (POWER) : Switches the unit ON or OFF.

Z OPEN/CLOSE : Opens and closes the disc

Drawer.


1 Preparation

2

Remote control a b c d

OPEN /

CLOSE

RADIO &

INPUT

CLEAR

SKIP SCAN

MONO/STEREO

REPEAT

SKIP

SPEAKER

LEVEL

SOUND

EFFECT

VOL

OPTICAL

MUTE e f g

PRESET

ENTER

PRESET

RETURN

TITLE

DISC MENU

MARKER SLEEP REC

AV / INPUT

VOL

VOL

PR/CH

PR/CH

• • • • • • • • • • e • • • • • • • • •

HOME : Displays the [Home] menu.

INFO./DISPLAY : Accesses On-Screen

Display.

U / u / I / i (up/ down/ left/ right): Used to navigate on-screen displays.

PRESET ( +/) : Selects programme of Radio.

TUNING -/+ : Tunes in the desired radio station.

 ENTER : Acknowledges menu selection.

Presetting the radio stations.

O RETURN : Moves backwards in the menu or exits the setup menu.

TITLE : If the current DVD title has a menu, the title menu appears on the screen. Otherwise, the disc menu may not appear.

DISC MENU : Accesses the menu on a DVD disc.

• • • • • • • • • • f • • • • • • • • •

MARKER : Marks play list.

SLEEP : Sets the System to turn off automatically at a specified time. (Dimmer :

The display window will be darken by half.) z REC : USB Direct Recording.

RDS : Radio Data System.

PTY : Views the various displays of the RDS.

• • • • • • • • • • g

• • • • • • • • •

TV Control buttons : Controls the TV. (LG TV only)

Controlling the TV.

You can control the sound level, input source, and power switching of LG TVs as well. Hold POWER (TV) and press PR/CH

(+/–) button repeatedly until the TV turns on or off.


Preparation 1

Front panel

a b c d e

2 l k a 1/\ (POWER)

Switches the unit ON or OFF. b Disc Tray c iPod Dock d Display window

Shows the current status of the unit.

e Z ( OPEN/CLOSE)

Opens or closes the disc tray.

f VOLUME

Adjusts speaker volume. g F (FUNCTION)

Changes the input source or function.

h .

/ > (SKIP)

Go to next or previous file/track/chapter.

Searches backward or forward (Press and hold)

Tunes in the desired radio station.

j i h g f i x (STOP)

Stops playback.

j N / X (PLAY / PAUSE)

Starts playback.

Pause playback temporarily, press again to exit pause mode. k USB Port

Connect a USB device.

l PORT. IN

Connect to a portable player with audio outputs.


1 Preparation

Rear panel

2 a b c d e a Power cord b Speakers connectors

Connect the speaker cables.

c Cooling Fan d Antenna Connector

FM- Connects the FM wired antenna e VIDEO OUT

Connect to a TV with video inputs.

j i h g f f HDMI OUT (Version 1.2A)

Connect to TV with HDMI inputs.

(Interface for digital audio and video) g HDMI IN (Version 1.2A) 1/2

Connect to an external source with HDMI output.

h OPTICAL IN

Connect to optical audio equipment.

i COMPONENT VIDEO (Y PB PR)OUTPUT

(PROGRESSIVE SCAN)

Connect to a TV with Y PB PR inputs.

j AUX (L/R) INPUT

Connect to an external source with 2 channel audio outputs.


Pole

Installation 1

Cable

3

Installation

Assembling the speaker stand to the speaker

1.

Pole

Step 1

Cable

Preparation

Base

Pole

Screw

2. Insert a speaker wire from the bottom of the base.

Step

Base

Speaker

3

Base

Screw

Screw

Speaker


Pole

Cable

Speaker

Base

Pole

Screw

Cable

Speaker

Base

Pole

Speaker

Cable

Screw

Base

Screw

3

1 Installation

3.

Draw the speaker wire through the inside of the pole and also through the hole on the bottom of the speaker.

Step

5.

Connect the speaker wire to the terminal on the speaker.

Make sure the wire marked black goes in to the terminal marked “–” (minus) and the other wire goes in to the terminal marked

“+” (plus).

Step

4.

Attach the speaker to the pole, the secure the connection with a supplied screw.

Step

CAUTION

Be careful that the speaker should not fall down.

Otherwise it may result in the speaker malfunctioning and causing personal injury and/ or property damage.


Mounting the speakers to a wall

Installation 1

3. Hang the speaker bracket onto the wall bracket.

Step

You can mount the speakers to a wall. Prepare screws and brackets supplied.

1. Attach the wall bracket to the wall with screws as shown in the illustration below.

When you mount to a wall (concrete) use the wall plugs. (supplied)

Screw length

. mm (0.1 inch)

mm (0. inch)

Step 1

Wall plug

Screw

4. Press the speaker to secure the brackets.

Step

2. Attach the speaker bracket to the speaker and fasten the screws.

Step

3


1 Installation

3

Attaching the speakers to the unit

1. Connect the wires to the unit.

Match each wire’s colored band to the same colored connection terminal on the rear of the unit. To connect the cable to the unit, press each plastic finger pad to open the connection terminal. Insert the wire and release the finger pad.

Color

Grey

Blue

Green

Orange Sub woofer Any front position

Red

White

Speaker

Rear

Rear

Center

Front

Front

Position

Rear right

Rear left

Center

Front right

Front left

To connect the cable to the speakers, press each plastic finger pad to open the connection terminals on the base of each speaker. Insert the wire and release the finger pad.

Connect the black end of each wire to the terminals marked -(minus) and the other end to the terminals marked + (plus).

. Connect the wires to the speakers.

Connect the other end of each wire to the correct speaker according to the color coding:

CAUTION

Be careful to make sure children not to put their hands or any objects into the *speaker duct.

*Speaker duct: A hall for plentiful bass sound on speaker cabinet (enclosure).


Installation 1

Positioning the system

The following illustration shows an example of positioning the system. Note that the illustrations in these instructions differ from the actual unit for explanation purposes.

For the best possible surround sound, all the speakers other than the subwoofer should be placed at the same distance from the listening position (

A

).

A

F

A

B

C

G

A

A

A

Front left speaker (L)/

B

Front right speaker (R):

Place the front speakers to the sides of the monitor or screen and as flush with the screen surface as possible.

C

Center speaker:

Place the center speaker above or below the monitor or screen.

D Surround left speaker (L)/

E

Surround right speaker (R):

Place these speakers behind your listening position, facing slightly inwards.

F

Subwoofer:

The position of the subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the front speakers. Turn it slightly toward the center of the room to reduce the wall reflections.

G

Unit

A

E

3

D

A

A A B C D E F G


0 Installation

Connections to Your

TV

3

Make one of the following connections, depending on the capabilities of your existing equipment.

NOTE

• Depending on your TV and other equipment you wish to connect, there are various ways you could connect the unit. Use only one of the connections described in this manual.

• Please refer to the manuals of your TV, Stereo

System or other devices as necessary to make the best connections.

• Make sure the unit is connected directly to the TV. Tune the TV to the correct video input channel.

• Do not connect your unit via your VCR. The image could be distorted by the copy protection system.

Component Video Connection

Connect the COMPONENT VIDEO OUTPUT

(PROGRESSIVE SCAN) jacks on the unit to the corresponding input jacks on the TV using component cables.

You can hear the sound through the system’s speakers.

Component Connection

Unit

HT965TZ-DH_BGBRLL_ENG_4246.indd 20

TV

Green

Blue

Red

2010-02-02 ¿ÀÈÄ 7:16:07

Installation 1

HDMI Out Connection

If you have a HDMI TV or monitor, you can connect it to this unit using a HDMI cable.

Connect the HDMI OUT jack on the unit to the HDMI IN jack on a HDMI compatible TV or monitor.

Set the TV’s source to HDMI (refer to TV’s

Owner’s manual).

HDMI Connection

Unit

HDMI IN 2

TIP

TV

• You can fully enjoy digital audio and video signals together with this HDMI connection.

• When you use HDMI connection, you can change the resolution for the HDMI output.

(Refer to “Resolution Setting” on page 24.)

NOTE

• If a connected HDMI device does not accept the audio output of the unit, the HDMI device

’s audio sound may be distorted or may not output.

• When you connect a HDMI or DVI compatible device make sure of the following:

- Try switching off the HDMI/DVI device and this unit. Next, switch on the HDMI/DVI device and leave it for around 30 seconds, then switch on this unit.

- The connected device’s video input is set correctly for this unit.

- The connected device is compatible with

720x480i (or 576i), 720x480p (or 576p),

1280x720p,1920x1080i or 1920x1080p video input.

• Not all HDCP-compatible HDMI or DVI devices will work with this unit.

- The picture will not be displayed properly with non-HDCP device.

- This unit does not playback and TV screen is changed to black or green screen or the snow noise may occur on the screen.

• If there is noise or lines on the screen, please check the HDMI cable and usea higher version cable than 1.2A HDMI cable.

3

CAUTION

• Changing the resolution when the connection has already been established may result in malfunctions. To solve the problem, turn off the unit and then turn it on again.

• When the HDMI connection with HDCP is not verified, TV screen is changed to black or green screen or the snow noise may occur on the screen. In this case, check the the HDMI connection, or disconnect the HDMI cable.


3

Installation

Video Connection

Connect the VIDEO OUT jack on the unit to the video in jack on the TV using a video cable.

You can hear the sound through the system’s speakers.

Video Connection

To connect to a TV with the

SCART jack

Connect the RCA to SCART cable form the

VIDEO OUT on the rear of the unit to the SCART jack on your TV.

RCA to SCART

Unit Unit

TV

TV

Yellow


Installation

Resolution Setting

The unit provides several output resolutions for

HDMI OUT and COMPONENT VIDEO OUT jacks.

You can change the resolution using [Setup] menu.

1. Press HOME .

2. Use I / i to select the [Setup] and press 

ENTER . The [Setup] menu appears.

Video Output

Resolution

Displayed resolution in display window and outputted resolution may different according to connection type.

[HDMI OUT]: 1080p, 1080i, 720p and 480p (or

576p) and 480i (or 576i)

[COMPONENT VIDEO OUT]: 480p (or 576p) and

480i (or 576i)

[VIDEO OUT]: 480i (or 576i)

3

3. Use U / u to select [Display] option then press i to move to the second level.

4. Use U / u to select the [Resolution] option then press i to move to the third level.

5. Use U / u to select the desired resolution then press  ENTER to confirm your selection.

NOTE

If your TV does not accept the resolution you have set on the player, you can set resolution to 480p (or

576p) as follows:

Press x (STOP) for more than 5 seconds.


Installation

Optional Equipment

Connection

3

HDMI IN connection

You can enjoy the pictures and sound of your component with this connection.

Connect the HDMI IN 1 or HDMI IN 2 jack on the unit to the HDMI output jack on your Set-

Top box (or Digital Device etc.) using an HDMI cable. Set the external source to HDMI IN 1 or

HDMI IN 2 by pressing t RADIO&INPUT .

HDMI IN Connection

NOTE

• You cannot change the video resolution at the

HDMI IN 1 or HDMI IN 2 mode. Change the video resolution of the connected component.

• If the video output signal is abnormal when your personal computer is connected to HDMI

IN 1 or HDMI IN 2 jack, change the resolution of your personal computer to 480p (or 576p), 720p,

1080i or 1080p.

• The video signal from the HDMI input cannot be output from the component or composite video outputs.

• The player sends audio from the HDMI inputs to both the HDMI output and to the unit’s speakers.

• You cannot operate SIMPLINK function at the

HDMI IN mode.

To the MDMI OUT jack of your component

(set-top box, digital satellite receiver, video game machine, etc.)


Installation

AUX IN Connection

Connect an Output of auxiliary device to the

AUX (L/R) INPUT Connector.

AUX IN Connection

AUDIO (PORT. IN) In

Connection

Connect an output of portable device (MP3 or PMP etc) to the AUDIO (PORT. IN) input connector.

PORT.IN Connection

Unit

MP3 player, etc...

3

To the audio output jacks of your component

(TV, VCR, etc.)

Red

White

NOTE

If your TV has only one output for audio (mono), connect it to the left (white) audio jack on the unit.

Listening to music from your portable player or external device

The unit can be used to play the music from many types of portable player or external devices.

1.

Connect the portable player to the

PORT.IN(PORTABLE IN) connector of the unit.

Or

Connect the external device to the AUX connector of the unit.

2.

Turn the power on by pressing 1 (POWER) .

3.

Select the PORTABLE or AUX (L/R) INPUT function by pressing t RADIO&INPUT .

4.

Turn on the portable player or external device and start it playing.


Installation

3

USB Connection

Connect the USB port of USB Memory (or MP3 player, etc.) to the USB port on the front of the unit.

USB Connection

Removing the USB Device from the unit

1. Choose a different function mode or press STOP ( x ) twice in a row.

2. Remove the USB device from the unit.

Compatible USB Devices

• MP3 Player : Flash type MP3 player.

• USB Flash Drive : Devices that support

USB2.0 or USB1.1.

• The USB function of this unit does not support some USB devices.

USB device requirement

• Devices which require additional program installation connected to a computer, are not supported.

• Do not extract the USB device while in operation.

• For a large capacity USB, it may take longer than a few minute to be searched.

• To prevent data loss, back up all data.

• If you use a USB extension cable or USB hub, the USB device is not recognized.

• Using NTFS file system is not supported.

(Only FAT(16/32) file system is supported.)

• This unit is not supported when the total number of files is 1 000 or more.

• External HDD, Card readers, Locked devices, or hard type usb devices are not supported.

• USB port of the unit cannot be connected to PC. The unit can not be used as a storage device.


Installation

OPTICAL In connection

Connect an optical output of Unit (or Digital

Device etc) to the OPTICAL IN connector.

OPTICAL IN Connection

Antenna Connection

Connect the supplied FM antenna for listening to the radio.

Connect the FM Wire antenna to the FM antenna connector.

Antenna Connection

3

To the digital optical output jack of your component

Home theater speaker ez setup

Listen to sound from TV, DVD and Digital

Device with 5.1(2.1 or 2)ch mode. Even in power off mode, if you press OPTICAL , then power is on and automatically changed to AUX

OPT mode.

1.

Connect the unit’s OPTICAL IN jack to jack on optical out of your TV (or Digital Device etc.).

2.

Select the AUX OPT by using the OPTICAL .

To select the AUX OPT directly

3.

Listen sound with 5.1(2.1 or 2)ch speaker.

4.

To escape from AUX OPT by using the

OPTICAL .

Function is retuned to previous one.

NOTE

Be sure to fully extend the FM wire antenna.

After connecting the FM wire antenna, keep it as horizontal as possible.


Installation

3

Adjust the setup settings

To display and exit the Setup menu

1.

Press HOME .

Displays the [Home] Menu.

By using the Setup menu, you can make various adjustments to items such as picture and sound.

You can also set a language for the subtitles and the Setup menu, among other things. For details on each Setup menu item, see pages 28 to 32.

OSD Initial language settings

During the first use of this unit, the initial language setup menu appears on your TV screen. You must complete initial language selection before using the unit. English will be selected as the initial language.

1.

Press 1 (POWER) to turn the unit on. The language setup menu will appear on the screen.

2.

Use U u I i to select a language then press  ENTER .

The confirm menu will appear.

2.

Select an [Setup] by using I i .

3.

Press  ENTER .

Displays the [Setup]

4.

Press HOME or O RETURN to exit in the [Setup] Menu.

About help menu for Setup

Buttons Menu v V

Move b

Move

B

Move

U u

I i

Operation

Moving to another menu.

Moving to previous level.

Moving to next level or selecting menu.

O

Close



Select

O

RETURN

To exit the [Setup] menu or [ 5.1

Speaker Setup].

 ENTER To confirm menu.

3.

Use I i to select the [Enter] then press 

ENTER to finish the language setup.


Installation

Language

Menu Language

Select a language for the Setup menu and then on screen display.

Disc Audio / Disc Subtitle / Disc

Menu

Select the language you prefer for the audio track (disc audio), subtitles, and the disc menu.

[Original]

Refers to the original language in which the disc was recorded.

[Other]

To select another language, press numeric buttons and then  ENTER to enter the corresponding 4-digit number according to the language code list on the page 46. If you enter the wrong language code, press

CLEAR .

[Off (for Disc Subtitle)]

Turn off Subtitle.

Display

TV Aspect

Select which screen aspect to use based on the shape of your TV screen.

[4:3]

Select when a standard 4:3 TV is connected.

[16:9]

Select when a 16:9 wide TV is connected.

Display Mode

The Display Mode setting works only when the

TV Aspect mode is set to 4:3.

[Letterbox]

Displays a wide picture with bands on the upper and lower portions of the screen.

[Panscan]

Automatically displays the wide picture on the entire screen and cuts off the portions that do not fit. (If the disc/file is not compatible with Pan Scan, the picture is displayed at Letterbox ratio.)

3

Resolution

Sets the output resolution of the Component and HDMI video signal. Refer to “Resolution

Setting” for details about the resolution (page

23).

[Auto]

If the HDMI OUT jack is connected to

TVs providing display information (EDID), automatically selects the resolution best suited to the connected TV. If the

COMPONENT VIDEO OUT is only connected, this changes the resolution to 480i (or 576i) as default resolution.

[1080p]

Outputs 1080 lines of progressive video.

[1080i]

Outputs 1080 lines of interlaced video.

[720p]

Outputs 720 lines of progressive video.

[480p (or 576p)]

Outputs 480 (or 576) lines of progressive video.

[480i (or 576i)]

Outputs 480 (or (576) lines of interlaced video.


0 Installation

3

Audio

5.1 Speaker Setup

Make the following settings for the built-in 5.1 channel surround decoder.

1.

Select [5.1 Speaker Setup] on the [Audio] menu.

2.

Press  ENTER .

The [5.1 Speaker setup] appears.

3.

Use I i to select the desired speaker.

4.

Adjust options using U u I i buttons.

5.

Returns to the previous menu by pressing

O RETURN .

[Speaker selection]

Select a speaker that you want to adjust.

NOTE

Certain speaker settings are prohibited by the

Dolby Digital licensing agreement.

[Size]

Since the speaker settings are fixed, you cannot change the settings.

[Volume]

Press I i to adjust the output level of the selected speaker.

Front L/R : 0 ~ -5

SubWoofer, Rear L/R, Center : 5 ~ -5

[Distance]

After you connected speakers to your unit, set the Distance between the speakers and your listening point if the distance of Center or Rear speakers is bigger than the distance of Front speakers. This allows the sound from each speaker to reach the listener at the same time. Press I i to adjust the

Distance of the selected speaker. This distance is equivalent to a difference of the distance between Center or Rear speaker and Front speakers.

[Test]

Select [Speaker Test Start] by using the U u and press  ENTER . Press  ENTER again to stop. Adjust the volume to match the volume of test signals memorized in the system.


Installation 1

DRC (Dynamic Range Control)

Make the sound clear when the volume is turned down (Dolby Digital only). Set to [On] for this effect.

Vocal

Select [On] to mix karaoke channels into normal stereo.

This function is effective for multi-channel karaoke DVDs only.

HD AV Sync

Sometimes Digital TV encounters a delay between picture and sound. If this happens you can compensate by setting a delay on the sound so that it effectively ‘waits’ for the picture to arrive: this is called HD AV Sync. Use U u

(on the remote control) to scroll up and down through the delay amount, which you can set at anything between 0 and 300m sec.

Lock (Parental Control)

Initial Setting the Area Code:

When you use this unit for the first time, you have to set the Area Code.

1.

Select the [Lock] menu and then press i .

2.

Press i .

To access the [Lock] options, you must input the password you have created. Input a password and press  ENTER . Enter it again and press  ENTER to verify. If you make a mistake before pressing  ENTER , press CLEAR .

3.

Select the first character using U u buttons.

4.

Press  ENTER and select the second character using U u buttons.

5.

Press  ENTER to confirm your Area code selection.

Rating

Blocks playback of rated DVDs based on their contents. Not all discs are rated.

1.

Select [Rating] on the [Lock] menu then press i .

2.

Input a password and press  ENTER .

3.

Select a rating from 1 to 8 using the U u buttons.

[Rating 1-8]

Rating one (1) has the most restrictions and rating eight (8) is the least restrictive.

[Unlock]

If you select unlock, parental control is not active and the disc plays in full.

4.

Press  ENTER to confirm your rating selection.

3


Installation

3

Password

You can enter or change password.

1.

Select [Password] on the [Lock] menu and then press i .

2.


To change the password, press  ENTER when the [Change] option is highlighted.

Input a password and press  ENTER . Enter it again and press  ENTER to verify.

3.

Press HOME to exit the menu.

Others

DivX VOD

We provide you with the DivX® VOD (Video On

Demand) registration code that allows you to rent and purchase videos using the DivX® VOD service.

For more information, visit www.divx.com/vod.

Press  ENTER when [DivX(R) VOD] is highlighted and you can view the registration code of the unit.

NOTE

If you forget your password, you can clear it using the following steps:

1. Select the [Setup] menu on the [Home] menu.

2. Input the 6-digit number “210499” and press

 ENTER . The password is cleared.

NOTE

All the downloaded videos from DivX VOD can only be played back on this unit.

Area Code

Enter the code of the area whose standards were used to rate the DVD video disc, based on the list on page 49.

1.

Select [Area Code] on the [Lock] menu then press i .

2.


3.

Select the first character using U u buttons.

4.

Press  ENTER and select the second character using U u buttons.

5.

Press  ENTER to confirm your Area code selection.


Operation

4

Operation

Using the Home Menu Basic Operations

1.

Press HOME .

Displays the [Home] menu.

2.

Select an option by using I i .

3.

Press  ENTER then selected option menu.

[Music] – Displays [MUSIC] menu.

[Movie] – Start video media’s playback or displays the [MOVIE] menu.

[Photo] – Displays [PHOTO] menu.

[Setup] – Displays the [Setup] menu.

NOTE

You can not select the [Music], [Movie] or [Photo] option when the USB device is not connected or a disc is not inserted.

1.

Insert the disc by using the Z OPEN/

CLOSE or Connect the USB device to the

USB port.

2.

Press HOME .

Displays the [Home] Menu.

3.

Select an option by using I i .

If you select the [Movie], [Photo] or [Music] option when you connect up to two devices, it appears as belows. Select a media then press  ENTER .

4.

Press  ENTER then selected option menu.

NOTE

• For the most Audio CD and DVD-ROM discs, playback starts automatically.

• The unit plays only music file contained in the

USB storage device or disc automatically.

4


Operation

4

To

Stop

Playback

Do this

Press x (STOP)

Press B (PLAY) , MONO/

STEREO .

Pause Press X (PAUSE/STEP) .

Frameby-Frame playback

Skipping to the next/ previous chapter/ track/ file

Press X (PAUSE/STEP) repeatedly to play title

Frame-by-Frame. (DVD, DivX only)

During playback, press

./> SKIP to go to the next chapter/ track/ file or to return to the beginning of the current chapter/ track/ file.

Press . SKIP twice briefly to step back to the previous chapter/ track/ file.

Locating a point quickly by playing a file in fast forward or fast reverse

During playback, press m / M SCAN repeatedly to select the required scan speed.

To return to normal speed, press B (PLAY) , MONO/

STEREO .

Playing repeatedly or randomly

Press s REPEAT repeatedly, and the current title, chapter or track will be played back repeatedly or randomly.

- DVD : Chapter/ Title/ Off

- DivX : Title/ All/ Off

- Audio CD/ MP3/ WMA :

Track/ All/ Random/ Off

Slowing down the playing speed

In the pause mode, press

SLOW ( bb or BB ) to select the required speed.

(DVD, DivX only) The DivX file cannot be slow down reverse playback.

Other Operations

Displaying Disc Information on-screen

You can display various information about the disc loaded on-screen.

1.

Press INFO./DISPLAY to show various playback information.

The displayed items differ depending on the disc type or playing status.

2.

You can select an item by pressing U u and change or select the setting by pressing

I i .

Title – Current title number/ total number of titles.

Chapter – Current chapter number/ total number of chapters.

Time – Elapsed playing time.

Audio – Selected audio language or channel.

Subtitle – Selected subtitle.

Angle – Selected angle/ total number of angles.

NOTE

If any button is not pressed for a few seconds, the on-screen display disappears .


Operation

To display the DVD Menu

DVD

When you play a DVD which contains several menu, you can select the menu you want using the Menu.

1.

Press DISC MENU .

The disc’s menu appears.

2.

Select the menu by using U u I i .

3.

Press B (PLAY) , MONO/STEREO to confirm.

To display the DVD title

DVD

When you play a DVD which contains several title, you can select the title you want using the

Menu.

1.

Press TITLE .

The disc’s title appears.

2.

Select the menu by pressing U u I i .

3.

Press B (PLAY) , MONO/STEREO to confirm.

1.5 times speed playback

Screen Saver

DVD

The 1.5 speed allows you to watch the pictures and listen to the sound quicker than playing at a normal speed.

1.

During playback, press B (PLAY) , MONO/

STEREO to play at 1.5 times speed. “ B X1.5” appears on the screen.

2.

Press B (PLAY) , MONO/STEREO again to exit.

The screen saver appears when you leave the unit in Stop mode for about five minutes.

Starting play from selected time

DVD DivX

To start playing at any chosen time on the file or title.

1.

Press INFO./DISPLAY during playback.

2.

Press U u to select the time clock icon and

“--:--:--” appears.

3.

Input the required start time in hours, minutes, and seconds from left to right. If you enter the wrong numbers, press CLEAR to remove the numbers you entered. Then input the correct numbers.

For example, to find a scene at 1 hour, 10 minutes, and 20 seconds, enter “11020” by using numerical buttons.

4.

Press  ENTER to confirm. Playback starts from the selected time.

Resume playback

DVD DivX ACD MP3 WMA

The unit records the point where you pressed the x (STOP) depending on the disc.

If “ Xx (Resume Stop)” appears on the screen briefly, press B (PLAY) , MONO/STEREO to resume playback (from the scene point).

If you press x (STOP) twice or unload the disc,

“ x ”(Complete Stop) appears on the screen.

The unit will clear the stopped point.

NOTE

The resume point may be cleared when a button is pressed (for example; 1 (POWER) , Z OPEN/

CLOSE , etc).

4


Operation

4

Marked Playback

ACD MP3

WMA

The mark function enables you to store your favourite files from any disc or USB device in the unit memory.

1.

Select [Music] on the [Home] menu.

Music menu

Returning to the upper folder. (MP3/ WMA only)

File information will be displayed according to the ID3TAG information on the appropriate music file. (MP3 only)

NOTE

If you want to select all files on the list, select

[Select All] and press  ENTER .

To delete a Marker

1.

Use U u to select the track that you wish to erase from the marked file.

2.

Press MARKER .

To delete all Markers

Use U u I i to select [Deselect All] then press

 ENTER in program edit mode.

NOTE

The markers are also cleared when the disc or

USB device is removed, the unit is switched to power off or the function is switched to others.

Selecting all tracks/ files.

Deselecting all tracks/files.

Moving to the previous or next file list.

2.

Select a desired music on the [List] by using the U u then press MARKER to appears the mark on the list.

3.

Press  ENTER or B (PLAY) , MONO/

STEREO .

Displays the play mode.

4.

Select the play mode by using the U u and press  ENTER .

[Mark Play]

Marked playback.

[Current Play]

Normal playback

Changing subtitle code page

DivX

If the subtitle is not displayed properly, you can change the subtitle code page to view the subtitle file properly.

1.

During playback, press INFO/DISPLAY to display the On-Screen display.

2.

Use U u to select the [Code Page] option.

3.

Use I i to select desired code option.

4.

Press O RETURN to exit the On-Screen display.


Operation

Viewing a PHOTO file

JPG

This unit can play discs with photo files.

1.

Select [Photo] on the [Home] menu and press  ENTER .

Photo menu


About help menu in the full screen.

Menu

Menu

Buttons

INFO./

DISPLAY

Operation

Displaying the

Option menu.

b

O

/ B

Prev./ Next

Close

I/i

O

RETURN

Moving to another file

Returning to the [Photo] menu.

Options while viewing a photo

You can use various options during viewing a photo in full screen.

1. While viewing a photo in full screen, press

INFO./DISPLAY to display the option menu.

2.

Select an option using U u I i .

Returning to the upper folder.

2.

Press U u to select a folder, and then press

 ENTER .

3.

If you want to view a slide show, press U u to highlight a file and press B (PLAY) ,

MONO/STEREO .

About help menu in the [Photo] menu.

Menu

B Slide

Show

Buttons

B (PLAY) ,

MONO/

STEREO

Operation

Viewing a slide show.

vVbB



Move

Select

O Close

U u I i

 ENTER

O

RETURN

Moving to another file or content.

Viewing a particular file.

Returning to the [Home] menu.

a b c d e a Current photo/ Total number of photos

– Use I i to view previous/next photo.

b Slide Show N / X – Press  ENTER to start or pause slide show.

c Speed x3/ x2/ x1 – Use  ENTER to select a delaying speed between photos in a slide show.

d Rotate – Press  ENTER to rotate the photo.

e Go to list – Press  ENTER to return

[Photo] menu.

4


Operation

Sleep Timer Setting

Press SLEEP one or more times to select delay time between 10 and 180 minutes, after the unit will turn off.

To check the remaining time, press SLEEP .

To cancel the sleep function, press SLEEP repeatedly until “SLEEP 10” appears, and then press SLEEP once again while “SLEEP 10” is displayed.

System Select - Optional

You must select the appropriate system mode for your TV system. Press and hold X (PAUSE/

STEP) for more than five seconds to be able to select a system in the [Home] menu. (PAL/

NTSC)

NOTE

If the USB device is connected or a disc is inserted, this function is not operated.

NOTE

You can check the remaining time before the

Unit turns off.

Press SLEEP The remaining time appears in the display window.

4

Dimmer

Press SLEEP once. The display window will be darken by half. To cancel it, press SLEEP repeatedly until dim off.

Turn off the sound temporarily

Press MUTE to mute your unit.

You can mute your unit in order, for example, to answer the telephone, appears the MUTE in the display window.

Adjust the speaker level settings

You can adjust the sound level of each speaker.

1.

Press SPEAKER LEVEL repeatedly to select a desired speaker to set.

2.

Press VOL -/+ to adjust the sound level of the selected speaker while the level setting memu is displayed on the display window.

3.

Repeat and adjust the sound level of the other speakers.

Last Scene Memory

DVD

This unit memorizes last scene from the last disc that is viewed. The last scene remains in memory even if you remove the disc from the unit or switch off the unit. If you load a disc that has the scene memorized, the scene is automatically recalled.


Operation

Radio Operations

Be sure that both FM aerials are connected.

(Refer to the page 27)

Listening to the radio

1.

Press t RADIO&INPUT until FM appears in the display window.

The last received station is tuned in.

2.

Press and hold TUNING (-/+) for about two seconds until the frequency indication starts to change, then release. Scanning stops when the unit tunes in a station.

or

Press TUNING (-/+) repeatedly.

3.

Adjust the volume by rotating VOLUME on the front panel or by pressing VOL (+/- )on the remote control repeatedly.

Presetting the Radio Stations

You can preset 50 stations for FM.

Before tuning, make sure that you have turned down the volume.

1.

Press t RADIO&INPUT until FM appears in the display window.

2.

Select the desired frequency by using

TUNING (-/+)

3.

Press  ENTER a preset number will flash in the display window.

4.

Press PRESET (-/+) to select the preset number you want.

5.

Press  ENTER .

The station is stored.

6.

Repeat the steps 2 to 5 to store other stations.

Deleting all the saved stations

1.

Press and hold CLEAR for two seconds.

"ERASE ALL" will flash up on the unit display.

2.

Press CLEAR to erase all saved of the radio stations.

4

Deleting a saved station

1.

Press PRESET - / + to Select a preset number you want to delete.

2.

Press CLEAR , the preset number will blink in the display window.

3.

Press CLEAR again, to delete the selectd preset number.

Improving poor FM reception

Press B (PLAY) , MONO/STEREO on the remote control. This will change the tuner from stereo to mono and usually improve the reception.


0 Operation

4

Seeing information about a radio station

The FM tuner is supplied with the RDS (Radio

Data System) facility. This shows information about the radio station being listened to. Press

RDS repeatedly to cycle through the various data types. :

PS

PTY

RT

(Programme Service Name)

The name of the channel will appear in the display

(Programme Type Recognition)

The programme type (e.g. Jazz or

News) will appear in the display.

(Radio Text)

A text message contains special information from the broadcast station. This text may scroll across the display.

CT (Time controlled by the channel)

This shows the time and date as broadcast by the station.

You can search the radio stations by programme type by pressing RDS . The display will show the last PTY in use. Press PTY one or more times to select your preferred programme type. Press I i . The tuner will search automatically, when a station is found the search will stop.


Operation 1

Sound adjustment

Setting the surround mode

This system has a number of pre-set surround sound fields. You can select a desired sound mode by using SOUND EFFECT .

You can change the SOUND EFFECT using

I i arrow key while the sound effect information is displayed on.

The displayed items for the equalizer maybe different depending on sound sources and effects.

On Display

NAT PLUS

NATURAL

Local specialization equalizer

AUTO EQ

POP

CLASSIC

JAZZ

ROCK

BASS

Description

You can enjoy the natural sound effect same as a

5.1-channel.

You can enjoy comfortable and natural sound

Regionally optimized sound effect. (DANGDUT/

ARABIC/ PERSIAN/ INDIA/

REGUETON/ MERENGUE/

SAMBA/ SALSA/ CUMBIA/

AFRO)

Realizes the sound equalizer that is the most similar to the genre of which is included in the MP3 ID3 tag of song files.

This program lends an enthusiastic atmosphere to the sound, giving you the feeling you are at an actual rock pop, jazz or classic concert.

During playback, reinforce the treble, bass and surround sound effect.

On Display

CLRVOICE

GAME

NIGHT

RETOUCH

LOUDNESS

VIRTUAL

PLII MOVIE

PLII MUSIC

BYPASS

Description

This program make voice sound clear, improving the quality of voice sound. (We encourage to use this EQ when you watch the movie of 5.1 channel.)

You can enjoy more virtual sound while playing video games.

This may be useful when you want to watch movies at low volume late at night.

When listening to MP3 files or other compressed music, you can enhance the sound.

This mode is available only to 2 channel sources.

Improves the bass and treble sound.

You can enjoy more virtual surround sound.

Dolby Pro Logic II enables you to play stereo source on

5.1-channel.

You can enjoy the sound without equalizer effect.

4

NOTE

• In some of surround modes, some speakers, there's no sound or low sound. It depends on the mode of surround and the source of audio, it is not defective.

• You may need to reset the surround mode, after switching the input, sometimes even after the sound track changed.


Operation

Advanced Operations

4

Recording to USB

You can record music or sound souce to USB device by connecting in to the port on the unit.

1.

Connect the USB device to the unit.

2.

Select a mode in which you want to record.

Play back a sound source first.

3.

Start the recording by pressing z REC .

4.

To stop recording, press x (STOP) .

[All tracks/ files recording]

Record to USB in stop or play mode.

[Program list recording]

After marking desired file(s) and you can record it to USB (Refer to the page 36).

It'll be stored as follows

Audio CD

MP3/ WMA

NOTE

• You can check the recording percentage rate for the USB record on the screen during the recording. (Audio CD or MP3/ WMA CD only)

• During recording MP3/WMA, there is no sound.

• When you stop recording during playback, the file that has been recorded at that time will be stored. (Audio CD only)

• Do not remove the USB device or turn off the unit during USB recording. If not, an incomplete file may be made and not deleted on PC.

• If USB recording does not work, the message like “NO USB”, “ERROR”, “USB FULL” or “NO REC” is displayed on the display window.

• Multi card reader divice or external HDD can not be used for USB recording.

• A file is recorded by 128 Mbyte (about 2 hours) when you record for a long term. There are recorded less than 4 files.

• When you stop recording during playback, the file will not be stored.

• In the state CD-G, DTS disc USB record is not operated.

• The files in the sub-folders are not recorded during all track recording.

• You may not record more than 999 files.

• The nunbering of the recording file is entered from the lowest number. So if you delete some of the recording files, the next recording file could be the lowest number among them.

The other sources

(Tuner, AUX,

Portable)

The making of unauthorized copies of copyprotected material, including computer programs, files, broadcasts and sound recordings, may be an infringement of copyrights and constitute a criminal offense. This equipment should not be used for such purposes.

Be responsible

Respect copyrights.


Operation

Playing the iPod

• Connect the iPod firmly.

To open the iPod Dock, pull iPod dock.

Connect the iPod

You can enjoy the media files with your iPod.

For details about iPod, refer to the iPod’s User

Guide.

Preparation

• To view iPod’s Videos and Photos on the TV screen.

- Be sure to use the video connection through the VIDEO OUT jack on the rear panel of this unit. Select the appropriate video input mode on the TV.

- Depending on the iPod, make sure that select Videos > Video settings, and then set TV Out to Ask or On from your iPod.

For details about Video Settings, refer to the iPod User Guide.

- The viewing photos is available only if this unit is in iPod IN mode and you can view photos only as a slide show. You have to start a slide show on your iPod to view a photo on a TV. For details about a slide show, refer to the iPod User Guide.

• Before connecting the iPod, turn this unit off and reduce the volume of this unit to its minimum.

• If you turn this unit on, your iPod is automatically turned on and recharging starts.

• If your iPod is completely discharged, charge the battery first.

4


Operation

4

Enjoying iPod on the screen

You can operate your iPod by controlling menu on the screen.

1. Connect the iPod firmly.

2. Press HOME .

3. Select [Music] or [Movie] using I / i , and press  ENTER .

If you connected the other device

(CD or USB), select the iPod on the menu and ENTER.

If you select the [Music] option when you connect iPod, the unit plays a music automatically.

4. Select a content using U / u / I / i , and press

 ENTER to play.

File information will be displayed according to the ID3TAG information on the appropriate music file. (MP3 only)

Enjoying the iPod IN mode

You can operate your iPod by using the supplied remote control and controls on your iPod.

1. Connect the iPod firmly.

2. Press t RADIO&INPUT to select iPod IN mode.

U / u / I / i Selects an option in the menu.

B (PLAY) ,

MONO/

STEREO

/  ENTER

Starts playback the music or video.

X m /

SCAN

M

To pause while it is playing.

To resume playing, press B

(PLAY) , MONO/STEREO again.

Fast-forward or rewind a song or video

./>

SKIP s

REPEAT

Skip the playback forward or backward .

To select a desired repeat mode: Track

(No display).

( ) , All ( ) , Off


5. Operate iPod.

Refer to basic operation section.

NOTE

• If the iPod’s OSD language is selected to simple chinese, the power scroll function is not operated correctly.

• The controls on your iPod are not operational in this mode.


Operation

NOTE

• An error message “CHECK IPOD” or “Connected iPod model is not supported.” appears when:

- your iPod is not available for the function to be operated.

• An error message “CHECK IPOD” or “Please update iPod’s software.” appears when:

- your iPod has an old software version. t Update your iPod software to latest version.

• If this unit displays an error message, follow the message. An error message “CHECK IPOD” or

“Please check your iPod.” appears when:

- the communication between this unit and your iPod is failed. t Undock & re-dock your iPod in this unit.

- your iPod is not connected firmly.

- this unit recognizes your iPod as unknown device.

- your iPod is exceptionally low on power. t The battery needs to be charged. t If you charge the battery while iPod is extremely low in power, it maytake longer to charge.

• You may use the dock adapter which should be supplied with your iPod to the dock for the stable use of the iPod. If you need an adapter, consult your iPod dealer.

• Compatibility with your iPod may vary depending on the type of your iPod.

• iPod touch and iPhone have any difference in operation other than iPod. You may need any additional control to use them with this unit.

(e.g. “slide to unlock”)

• If you use an application, make a call, or send and receive SMS text message, etc. on iPod touch or iPhone, disconnect it from iPod dock of this unit and then use it.

• Depending on your iPod’s software version, it may not be possible to control your iPod from this unit. We recommend installing the latest software version.

• The video quality depends on the video sources on your iPod.

• If you have a problem with your iPod, please visit www.apple.com/support/ipod.

• You cannot use the microphone on the iPod mode.

4


Maintenance

5

Maintenance

Notes on Discs Handling the Unit

5

Handling Discs

Never stick paper or tape on the disc.

Storing Discs

After playing, store the disc in its case. Do not expose the disc to direct sunlight or sources of heat and never leave it in a parked car exposed to direct sunlight.

Cleaning Discs

Do not use strong solvents such as alcohol, benzine, thinner, commercially available cleaners, or anti-static spray intended for older vinyl records.

When shipping the unit

Please save the original shipping carton and packing materials. If you need to ship the unit, for maximum protection, re-pack the unit as it was originally packed at the factory.

Keeping the exterior surfaces clean

• Do not use volatile liquids such as insecticide spray near the unit.

• Wiping with strong pressure may damage the surface.

• Do not leave rubber or plastic products in contact with the unit for a long period of time.

Cleaning the unit

To clean the player, use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly moistened with a mild detergent solution. Do not use strong solvents such as alcohol, benzine, or thinner, as these might damage the surface of the unit.

Maintaining the Unit

The unit is a high-tech, precision device. If the optical pick-up lens and disc drive parts are dirty or worn, the picture quality could be diminished. For details, please contact your nearest authorized service center.


Troubleshooting

6

Troubleshooting

PROBLEM

No power

No picture

There is little or no sound

CAUSE

The power cord is disconnected.

The TV is not set to receive the DVD signal.

The video cables are not connected securely.

Equipment connected via the audio cable is not set to receive DVD signal output.

The audio cables are not connected to the speakers or unit securely.

The audio cables are damaged.

CORRECTION

Plug the power cord into the wall outlet securely.

Select the appropriate video input mode on the TV so the picture from the unit appears on the TV screen.

Connect the video cables securely to both the TV and unit.

Select the correct input mode of the unit so you can hear the sound from the unit.

Connect the audio cables into the connection terminals correctly.

Replace with a new audio cable.

The DVD picture quality is poor

The disc is dirty.

Clean the disc using a soft cloth with outward strokes.

A DVD/CD will not play

Humming noise heard while a

DVD or CD is playing

Radio stations can’t be tuned in properly

The remote control doesn’t work well / at all

No disc is inserted.

An unplayable disc is inserted.

The disc is inserted upside down.

There is a parental lock which prevents the playback of DVDs with a certain rating.

The disc is dirty.

Insert a disc.

Insert a playable disc (check the disc type, colour system and regional code).

Place the disc with the label or printed side facing upwards.

Enter your password or change the rating level.

Clean the disc using a soft cloth with outward strokes.

Move unit and audio components further away from your TV.

The unit is located too close to the TV, causing feedback.

The antenna is positioned or connected poorly.

Check the antenna connection and adjust its position.

Attach an external aerial if necessary.

The signal strength of the radio station is too weak.

No stations have been preset or preset stations have been cleared (when tuning by scanning preset channels).

Tune to the station manually.

Preset some radio stations, see page for details.

The remote is not pointed directly at the unit.

Point the remote directly at the unit.

The remote is too far from the unit.

Use the remote within feet (m) of the unit.

There is an obstacle in the path between the remote control and the unit.

Remove the obstacle.

The battery in the remote control are flat.

Replace the batteries with new ones.

6


Appendix

7

Appendix

Language Codes

7

Use this list to input your desired language for the following initial settings: Disc Audio, Disc

Subtitle, Disc Menu.

Language Code Language

Afar

Afrikaans

Albanian

Ameharic

Arabic

Armenian

Assamese

Aymara

Azerbaijani

Bashkir

6590

6665

Basque 6985

Bengali; Bangla 6678

Bhutani

Bihari

Breton

Bulgarian

6890

6672

6682

6671

6565

6570

8381

6577

6582

7289

6583

6588

Burmese

Byelorussian

Chinese

Croatian

Czech

Danish

Dutch

English

Esperanto

Estonian

Faroese

Fiji

Finnish

7789

6669

9072

7282

6783

6865

7876

6978

6979

6984

7079

7074

7073

Code

French

Frisian

Galician

Georgian

German

Greek

Greenlandic

Guarani

Gujarati

Hausa

Hebrew

Hindi

Hungarian

Icelandic

Indonesian

Interlingua

Irish

Italian

Javanese

Kannada

Kashmiri

Kazakh

Kirghiz

Korean

Kurdish

Laothian

7585

7679

Latin 7665

Latvian, Lettish 7686

Lingala 7678

7165

7384

7487

7578

7583

7575

7589

7579

7185

7265

7387

7273

7285

7383

7378

7365

7082

7089

7176

7565

6869

6976

7576

7178

Language Code

Lithuanian

Macedonian

Malagasy

Malay

Malayalam

Maori

Marathi

Moldavian

Mongolian

Nauru

Nepali

Norwegian

7778

7865

7869

7879

Oriya

Panjabi

7982

8065

Pashto, Pushto 8083

Persian 7065

7684

7775

7771

7783

7776

7773

7782

7779

Polish

Portuguese

8076

8084

Quechua 8185

Rhaeto-Romance 8277

Rumanian

Russian

Samoan

Sanskrit

8279

8285

8377

8365

Scots Gaelic

Serbian

7168

8382

Serbo-Croatian 8372

Shona 8378

Sindhi 8368

Language

Singhalese

Slovak

Slovenian

Spanish

Sudanese

Swahili

Swedish

Tagalog

Tajik

Tamil

Telugu

Thai

Tonga

Turkish

Turkmen

Twi

Ukrainian

Urdu

Uzbek

Vietnamese

Volapük

Welsh

Wolof

Xhosa

Yiddish

Yoruba

Zulu

Code

8575

8582

8590

8673

8679

6789

8779

8872

7473

8979

9085

8471

8465

8469

8472

8479

8482

8475

8487

8373

8375

8376

6983

8385

8387

8386

8476


Appendix

Area Codes

Choose a area code from this list.

Area

Afghanistan

Argentina

Australia

Austria

Belgium

Bhutan

Bolivia

Brazil

Cambodia

Canada

Chile

China

Colombia

Congo

Costa Rica

Croatia

Czech Republic

Denmark

Ecuador

Egypt

El Salvador

Ethiopia

Fiji

Finland

France

Germany

Great Britain

Greece

Code

SV

ET

FJ

FI

CZ

DK

EC

EG

FR

DE

GB

GR

CO

CG

CR

HR

KH

CA

CL

CN

BE

BT

BO

BR

AF

AR

AU

AT

Area

Greenland

Hong Kong

Hungary

India

Indonesia

Israel

Italy

Jamaica

Japan

Kenya

Kuwait

Libya

Luxembourg

Malaysia

Maldives

Mexico

Monaco

Mongolia

Morocco

Nepal

Netherlands

Netherlands Antilles

New Zealand

Nigeria

Norway

Oman

Pakistan

Panama

Code

NL

AN

NZ

NG

MC

MN

MA

NP

NO

OM

PK

PA

LU

MY

MV

MX

JP

KE

KW

LY

ID

IL

IT

JM

GL

HK

HU

IN

Area

Paraguay

Philippines

Poland

Portugal

Romania

Russian Federation

Saudi Arabia

Senegal

Singapore

Slovak Republic

Slovenia

South Africa

South Korea

Spain

Sri Lanka

Sweden

Switzerland

Taiwan

Thailand

Turkey

Uganda

Ukraine

United States

Uruguay

Uzbekistan

Vietnam

Zimbabwe

Code

UG

UA

US

UY

CH

TW

TH

TR

UZ

VN

ZW

KR

ES

LK

SE

SG

SK

SI

ZA

RO

RU

SA

SN

PY

PH

PL

PT

7


0 Appendix

Trademarks and

Licenses

Energy Saving ( Extremely Low Power

Consumption)

On the LG products, an innovative power consumption system in stand-by mode is built.

It consumes less than 0.09 watts in that mode.

Therefore, the small amounts of electricity are consumed even though the power plug is inserted.

Manufactured under license from Dolby

Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

iPod is trademark of Apple Inc., registered in the U.S. and other countries.

Manufactured under license under U.S. Patent

#’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762;

6,487,535 & other U.S. and worldwide patents issued & pending. DTS and DTS Digital Surround are registered trademarks and the DTS logos and

Symbol are trademarks of DTS, Inc. © 1996-2007

DTS, Inc. All Rights Reserved.

HDMI, the HDMI logo and High-Definition

Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC.

iPhone is a trademark of Apple Inc.

“Made for iPod” means that an electronic accessory has been designed to connect specifically to iPod and has been certified by the developer to meet

Apple performance standards.

“Works with iPhone” means that an electronic accessory has been designed to connect specifically to iPhone and has been certified by the developer to meet Apple performance standards.

Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards

7

“DVD Logo” is a trademark of DVD Format/Logo

Licensing Corporation.

DivX is a registered trademark of DivX, Inc., and is used under license.


Appendix 1

What is SIMPLINK?

Some functions of this unit are controlled by TV’s remote control when this unit and LG TV with SIMPLINK are connected through HDMI connection. Controllable functions by LG TV’s remote control; Play,

Pause, Scan, Skip, Stop, Power Off, etc.

• Refer to the TV owner’s manual for the details of SIMPLINK function.

• LG TV with SIMPLINK function has the logo as shown above.

• Use a higher version cable than 1.2 A

HDMI cable.

Specifications

•

•

•

•

•

•

•

General

Power requirements:

Refer to main label

Power consumption:

Refer to main label

Dimensions (W x H x D):

430 x 62.5 x 283.6 mm without foot

Net Weight (Approx.):

3.8 kg

Operating temperature:

41 °F to 95 °F (5 °C to 35 °C)

Operating humidity:

5 % to 90 %

Bus Power supply (USB):

DC 5 V 500 mA

•

•

•

•

•

•

Inputs/ Outputs

VIDEO OUT:

1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1

COMPONENT VIDEO OUT:

(Y) 1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1,

(Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA jack x 2

HDMI IN/OUT (video/audio):

19 pin (HDMI standard, Type A)

HDMI version : 1.2A

ANALOG AUDIO IN:

2.0 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R) x 1

DIGITAL IN (OPTICAL 1):

3 V (p-p), Optical jack x 1

PORT. IN:

0.5 Vrms (3.5 mm stereo jack)

Tuner

FM Tuning Range:

87.5 to 108.0 MHz or 87.50 to 108.00 MHz

7


7

Appendix

•

•

Amplifier

Stereo mode: 180 W + 180 W (4 Ω at 1 KHz)

Surround mode:

Front

Center

180 W + 180 W (4 Ω at 1 KHz)

180 W (4 Ω at 1 KHz)

Surround 180 W + 180 W (4 Ω at 1 KHz)

Subwoofer 200 W (3 Ω at 60 Hz)

•

•

•

•

Speakers

Front speaker

Type:

Impedance :

Rated Input Power:

Max. Input power:

Net Dimensions

(W x H x D):

Net Weight:

Rear speaker

Type:

Impedance

Rated Input Power:

Max. Input power:

Net Dimensions

(W x H x D):

Net Weight:

Center speaker

Type:

Impedance:

Rated Input Power:

Max. Input power:

Net Dimensions

(W x H x D):

Net Weight:

Passive Subwoofer

Type:

Impedance:

Rated Input Power:

Max. Input power:

Net Dimensions

(W x H x D):

Net Weight:

2 Way 3 speaker

4 Ω

180 W

360 W

280 x 1 212 x 194 mm

2.5 kg

2 Way 3 speaker

4 Ω

180 W

360 W

280 x 1 212 x 194 mm

2.5 kg

2 Way 3 speaker

4 Ω

180 W

360 W

400 x 75 x 52 mm

0.55 kg

1 Way 1 speaker

3 Ω

200 W

400 W

196 x 394 x 320 mm

5.8 kg


Warranty

Technology with the human touch

GUARANTEE

• LG Electronics U.K. Ltd. will provide the following services in order toexpedite this Guarantee.

1. All faulty components which fail due to defective manufacture will be replaced free of charge for a period of 12 months from the original date of purchase.

2. The dealer (or his service agent) who sold the product will be reimbursed for any labour provided in the repair of this LG equipment, for a period of 12 months from the original date of purchase. These claims must be made in accordance with the published scale of service charges and relevant claims procedure.

PLEASE NOTE:

A. The dealer may restrict the guarantee to the original purchaser.

B. The dealer is not obliged to carry out service under guarantee if unauthorized modifications are made to the apparatus, or if non standard components are used or if the serial number of the apparatus is removed, defaced, misused, or altered.

•

•

C. Any claims made under guarantee must be directed to the dealer from whom the equipment was originally purchased. The dealer may, before carrying out service under guarantee, require a receipted account as evidence of the date of purchase.

D. We respectfully point out that your dealer is not obligated to replace batteries if they become exhausted or worn in use.

E. Aerial alignment and consumer control adjustments are not covered by this guarantee.

•

This guarantee does not affect your statutory rights.

REQUIREMENTS TO MAINTAIN WARRANTY COVERAGE:

RETAIN YOUR RECEIPT TO PROVE DATE OF PURCHASE. A COPY OF YOUR RECEIPT MUST BE SURRENDERED

AT THE TIME GUARANTEE SERVICE IS PROVED.

Product Registration Card :

It is helpful to complete at least your name, address, phone, model & serial numbers and return it. This will enable LG to assist you in the future should you lose your receipt, your units be stolen, or should modifications be necessary.

To obtain information or assistance: Call 0870 873 5454 Monday-Friday 9.00am-4.30pm

MODEL NO.* SERIAL NO.* DATE OF PURCHASE.*

In all cases of difficulty - consult your LG dealer from whom the product was purchased

LGEUK Website : www.lge.co.uk

( service website : www.lgelectronics.co.uk ) 8


As an ENERGY STAR® Partner,

LG has determined that this product or product models meet the ENERGY STAR® guidelines for energy efficiency.

ENERGY STAR® is a U.S. registered mark.


No results