LG LVC-SX701OC Instruction manual

LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 1
Color Video Camera
Instruction Manual
Models : LVC-SX701PC/OC/MC
Before installing, operating or adjusting this
product, please read this instruction booklet
carefully and completely.
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to the
presence of uninsulated dangerous voltage within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the product.
FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may
cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the
authority to operate this equipment if an unauthorized change
or modification is made.
Regulatory Notices For U.S.A
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in
a commercial environment.
2
Page 2
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required
to correct the interference at his own expense.
• A suitable conduit entries, knock-outs or glands shall be
provided in the cable entries of this product in the end user.
• Caution: Danger of explosion if battery is incorrectly replaced.
Replaced only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
• Holes in metal, through which insulated wires pass, shall have
smooth well rounded surfaces or shall be provided with brushings.
Warning: Do not install this equipment in a confined space such as
a bookcase or similar unit.
Warning: Wiring methods shall be in accordance with the National
Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic environment this
product may cause radio interference in which case the user may be
required to take adequate measures.
Warning: To reduce a risk of fire or electric shock, do not expose
this product to rain or moisture.
Caution: This installation should be made by a qualified service person and should conform to all local codes.
Caution: To avoid electrical shock, do not open the cabinet. Refer
servicing to qualified personnel only.
Caution: The apparatus should not be exposed to water (dripping or
splashing) and no objects filled with liquids, such as vases, should
be placed on the apparatus.
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 3
Important Safety Instructions
4. Follow all instructions. - All operating and use
instructions should be followed.
7. Do not block any ventilation openings. Install
in accordance with the manufacturer’s instructions. - Slots and openings in the cabinet are
provided for ventilation, to ensure reliable operation of the product, and to protect it from
over- heating. The openings should never be
blocked by placing the product on a bed, sofa,
rug or other similar surface. This product should
not be placed in a built-in installation such as
a bookcase or rack unless proper ventilation is
provided and the manufacturer’s instructions
have been adhered to.
5. Do not use this apparatus near water. – For
example: near a bath tub, wash bowl, kitchen
sink, laundry tub, in a wet basement; near a
swimming pool; etc.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
1. Read these instructions. - All these safety and
operating instructions should be read before the
product is operated.
2. Keep these instructions. - The safety, operating and use instructions should be retained for
future reference.
3. Heed all warnings. - All warnings on the product and in the operating instructions should be
adhered to.
6. Clean only with dry cloth. – Unplug this product from the wall outlet before cleaning. Do not
use liquid cleaners.
3
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 4
Important Safety Instructions
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade
or the third prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement
of the obsolete outlet.
10. Protect the power cord from being walked
on or pinched particularly at plugs, convenience receptacles, and the point where they
exit from the apparatus.
11. Only use attachments/
accessories specified by
the manufacturer.
4
12. Use only the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold
with apparatus. When a cart is used, use
caution when moving the cart/ apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning
storms or when unused for long periods of
time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way,
such as powersupply cord or plug is damaged, liquid has
been spilled or objects have fallen into the
apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has been dropped.
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 5
Contents and Features
Contents
Important Safety Instructions . . . . . . . . . . . .3-4
Contents and Features . . . . . . . . . . . . . . . . . .5
Features Chart . . . . . . . . . . . . . . . . . . . . . . .6
Cautions for Safe Operation . . . . . . . . . . . . . . .7
Part Names and Functions . . . . . . . . . . . . . .8-10
Connections . . . . . . . . . . . . . . . . . . . . . . . .11
Mounting the Lens . . . . . . . . . . . . . . . . . . . .12
Concerning Auto-Iris Lenses . . . . . . . . . . . . . .13
External Device Connections . . . . . . . . . . . . . .14
Flange-back Adjustment . . . . . . . . . . . . . . . .15
Installation of Camera . . . . . . . . . . . . . . . . .16
Menu Operation . . . . . . . . . . . . . . . . . . . .17-18
Language and Camera Identification Settings . . .19
Exposure Settings . . . . . . . . . . . . . . . . . .20-24
White Balance Settings . . . . . . . . . . . . . . .25-27
Day/Night Setting . . . . . . . . . . . . . . . . . . . .28
Motion Detector Setting (MOTION DET) . . . .29-30
Privacy Masking Setting . . . . . . . . . . . . . . . .31
Special Menu Settings . . . . . . . . . . . . . . .32-37
RS-485 Protocol . . . . . . . . . . . . . . . . . . . . .38
Specifications . . . . . . . . . . . . . . . . . . . . .39-40
Features
This color video camera is designed for use in monitoring system.
• High resolution and high sensitivity with a 1/ 3
inch Super HAD CCD (Charge Coupled Device)
• Line Lock when using AC 24V power.
• C/CS Mount
5
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 6
Features Chart
This page shows the differences between the models.
Models
LVC-SX701PC
LVC-SX701OC
LVC-SX701MC
DAY/NIGHT
Yes
Yes
Yes
WDR
Yes
No
No
DSS
Yes
Yes
No
Power Source
AC24V (60Hz) / DC12V
AC24V (60Hz) / DC12V
AC24V (60Hz) / DC12V
Models LVC-SX701PC are used for the description, operation, and details provided in this
operating guide.
6
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 7
Cautions for Safe Operation
Power Supply
This camera must always be operated a AC 24V or
DC 12V Certified/Listed, class 2 power supply only.
Note: Be careful of AC frequency when the camera
is operated with Line lock mode.
Handling of the unit
Be careful not to spill water or other liquids on the
unit. Be cautions not to get combustible or metallic material inside the body. If used with foreign
matter inside, the camera is liable to fail or to get
cause of fire or electric shock.
Operating and storage location
Avoid viewing a very bright object (such as light
fittings) during an extended period. Avoid operating or storing the unit in the following locations.
• Extremely hot or cold places (operating temperature -10 °C - 50 °C, however, we recommend
that the unit be used within a temperature range
of 0 °C - 45 °C)
• Damp or dust place
• Places exposed to rain
• Places subject to strong vibration
• Close to generators of powerful electromagnetic
radiation such as radio or TV transmitters.
Handling of the unit
• Remove dust or dirt on the surface of the lens
with a blower.
• Use a dry soft cloth to clean the body.If it is
very dirty,use a cloth dampened with a small
quantity of neutral detergent,then wipe dry.
• Avoid the use of volatile solvents such as thinners,alcohol,benzene,and insecticides.
They may damage the surface finish and/or
impair the operation of the camera.
7
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 8
Part Names and Functions
1 2
3
4
1. Lens mount cap
The cap is installed to protect the lens mount
section. Remove the lens mount cap before
installing a lens (sold separately) .
2. Flange-back adjustment dial
3. Flange-back lock screw
4. Camera installation bracket
The bracket can be fixed at the top or bottom
of the camera. (page 16)
8
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 9
Part Names and Functions
5
6
7
8
5. Power input terminal
AC 24 V or DC 12 V input terminal
6. Video output connector (BNC type)
Connect this connector to a device such as a
VCR or monitor with a VIDEO IN connector.
7. Power indicator
Comes on when the power to the camera is on.
8. External Device Connectors
RS-485 Connector
Connect to an external controller of RS-485 format.
Alarm Output Terminal (ALARM OUT/GND)
Connect to the alarm input of an external
device.
Multi Input Terminal
Connect to an external wired remote control.
9
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 10
Part Names and Functions
9
10 11
9.
Buttons for menu
To set items on the MEMU, use the these buttons on the side panel. (page 17)
10. ALC Lens Setting Switch
DC: When you attach an Auto Iris lens requiring the DC control signal, please put this
switch in the DC position.
ELC: When you attach a manual or fixed lens,
please put this switch in the ELC position.
VIDEO: When you attach an Auto Iris lens
requiring the video control signal, please put
this switch in the VIDEO position.
11. Lens iris output connector (LENS)
This 4- pin connector is used to send the Iris
control signal and power supply to an autoiris type lens.
10
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 11
Connections
Basic connection
3
The peripheral devices (VCR, monitor, lens, etc.),
AC adaptor and cables are not supplied.
2
1. Connecting the monitor
Make the video signal connection between the
camera and the monitor or time lapse VCR.
1
2. Use a commercially available AC 24 V
adaptor.
Connect an AC 24 V power source to the AC 24V
input terminal on the back of the camera.
3. Insert the plug of this power cord into a wall
outlet.
The POWER indicator will light. Adjust the picture on the monitor using the Brightness and
Contrast controls etc.
To monitor’s Video Input
or Camera Input
11
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 12
Mounting the Lens
1. Remove the lens mount cap from the camera.
2. Install the auto-iris lens.
2-1. CS mount type lens
Carefully align the lens mount with the camera
opening, then turn the lens slowly to install it.
1
2-2
3
12
2-1
2-2. C mount type lens
To allow for flange- back adjustment, install the
C-mount adaptor (option) on the lens mount,
then carefully align the lens mount with the
camera opening and turn the lens slowly to
install it.
3. Connect the lens plug to the lens iris output
connector (LENS) on the side of the camera.
When using lenses from other makers, the plug
shape may not correspond to the terminal on
the camera.
In such a case, remove the original plug and
using a soldering iron, connect a lens iris plug
according to the diagram. (Refer to next page.)
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 13
Concerning Auto-Iris Lenses
ELC type auto-iris lens
Use a manual or fixed iris lens (Set the ALC Lens
Setting Switch to the ELC position.)
DC type auto-iris lens
A lens without driver circuit that operates only on
a DC power source. In general, this type of lens is
referred to as DC type coil lens. (Set the ALC Lens
Setting Switch to the DC position.)
VIDEO type auto-iris lens
A lens with amplifier circuit that operates on video
signal and DC power source. In general, this type of
lens is referred to as EE amplifier type lens.
ALC and LEVEL volume level controls are available
on the lens for iris adjustments. (Set the ALC Lens
Setting Switch to the VIDEO position.)
CAUTION: Be cautions not to use Auto Iris Lens
with over 50mA.
If using a VIDEO type auto-iris lens
• Set the ALC and LEVEL controls on the lens to
adjust the iris. Normally the ALC volume should
be turned all the way to Av (Average).
• Depending on the type of lens used, the lens
may not perform properly. In such a case, adjust
the LEVEL volume on the lens casing to correct.
Pin layout for the lens iris output connector
No.
1
2
3
4
DC type lenses
Damp Damp +
Drive +
Drive -
VIDEO type lenses
Vcc (+12V)
Not used
Video
Ground
13
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 14
External Device Connections
RS-485 (TR+)
RS-485 (TR-)
ALARM (OUT)
ALARM (COM)
MULTI (INPUT)
MULTI (GND)
RS-485 Connection
Connect to an external controller of RS-485 format.
Alarm Connection
Connect an external device such as a buzzer or
lamp to the ALARM terminal. When the camera
detects motion, the alarm output signal is supplied
to the connected external device.
14
Contact Ratings
• Maximum load current is ±130mA.
• Do not connect any system or
device that has over 40 Vp-p
(DC 30 V) bias voltage on the
contact terminal.
ALARM
COM
Equivalent Diagram
Notes:
Use a relay unit if the voltage or current of the
connected device exceeds the ratings.
Multi-Input Connection
Connect an external device to use HOT KEY function. The HOT KEY function is operated when the
input signal is “ON”. To set the HOT KEY function,
see page 35.
The Multi-Input terminal has the register of DC
3.3V pull-up. The sink current must be less than
0.8mA.
OFF: Open contact
ON: Closed contact
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 15
Flange-back Adjustment
The adjustment is required only when a lens without focus-adjusting mechanism is mounted, or
when a lens with adjusting mechanism is mounted
and focus that is more accurate is needed.
flange-back
fixing screw
flange-back
adjusting ring
1 Loosen the flange-back fixing screw on the
flange-back adjusting ring.
2. Turn the flange-back adjusting ring to obtain a
focused point while watching the monitor
screen.
3. Tighten the flange-back fixing screw on the
flange-back adjusting ring.
Caution:
Tightening the screw by force will cause damage to
the screw or deviation of focus.
Note: The object may be out of focus when using a
source of near-infrared light than using the visible
light.
15
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Installation of Camera
The bracket can be installed to either the top of
the camera as desired. When changing the position
of the camera mounting bracket, you should always
reuse the screws that have been removed.
Note:
If using a camera mounting bracket, select a location that is strong enough to bear the full weight
of the camera and the mounting bracket for long
periods, and install the camera and mounting
bracket securely.
16
Page 16
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 17
Menu Operation
This camera utilizes an on-screen user MENU. To set
items on the menu, use the following buttons on
the side panel.
Up Button
Set Button
Right Button
Left Button
Down Button
Right button: Moves the cursor to the right.
Use this button to select or adjust the parameters of the selected item. The parameter
changes each time this button is pressed.
Left button: Moves the cursor to the left. Use
this button to select or adjust the parameters
of the selected item. The parameter changes
each time this button is pressed.
Set button: Executes selections and displays a
submenu for an item with the
mark.
Up button: Moves the cursor upwards. Use this
button to select an item or adjust the parameters.
Down button: Moves the cursor downwards. Use
this button to select an item or adjust the
parameters.
17
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Menu Operation
To Open and Exit the Menu screen
Press and hold down
for 2 seconds or more.
The MENU screen appears on the monitor as shown
below. Check the current settings on the menu.
Press and hold down
for 2 seconds or more to
exit the menu screen.
LANGUAGE
CAMERA ID
EXPOSURE
WHITE BAL
DAY/NIGHT
MOTION DET
PRIVACY MASK
SPECIAL
INITIAL SET
EXIT
18
MENU
ENGLISH
OFF
PUSH AUTO
AUTO
OFF
OFF
Page 18
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 19
Language and Camera Identification Settings
LANGUAGE
CAMERA ID
EXPOSURE
WHITE BAL
DAY/NIGHT
MOTION DET
PRIVACY MASK
SPECIAL
INITIAL SET
EXIT
MENU
ENGLISH
OFF
PUSH AUTO
AUTO
OFF
Language Setting
Select a language for the Setup menu and on-screen display.
1. Select [LANGUAGE] option on the [MENU] screen.
2. Press left or right button to select a language.
OFF
Camera Identification Setting
LANGUAGE
CAMERA ID
EXPOSURE
WHITE BAL
DAY/NIGHT
MOTION DET
PRIVACY MASK
SPECIAL
INITIAL SET
EXIT
MENU
ENGLISH
OFF
PUSH AUTO
AUTO
OFF
You can use the camera identification (CAMERA ID) to assign a number to the camera (0 - 255, OFF).
The camera identification’s number is displayed on the lower left of
the screen. To disappear the number, select [OFF].
1. Select [CAMERA ID] option on the [MENU] screen.
OFF
2. Use
or
button to select a ID number of the camera.
19
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 20
Exposure Settings
LANGUAGE
CAMERA ID
EXPOSURE
WHITE BAL
DAY/NIGHT
MOTION DET
PRIVACY MASK
SPECIAL
INITIAL SET
EXIT
1. Select [EXPOSURE] option on the [MENU] screen.
2. Press
PUSH AUTO
AUTO
OFF
,
, or
button and the EXPOSURE menu appears.
3. To reset the [EXPOSURE] settings to factory setting, select [INITIAL SET] option then press
on the [EXPOSURE] menu.
4. To return to the previous menu, select [RETURN] option then
press .
OFF
EXPOSURE
BRIGHTNESS
AGC MAX
MEDIUM
SHUTTER
AUTO
FLIKERLESS
OFF
BLC/WDR
OFF
LEVEL
OFF
AREA
SPECIAL
INITIAL SET
ON
RETURN
20
You can set the exposure options using the EXPOSURE menu.
MENU
ENGLISH
OFF
+
Brightness Setting
You can set the brightness level. (7 levels)
1. Select [EXPOSURE] option on the [MENU] screen then press
, , or
button. The EXPOSURE menu appears.
2. Use
or
button to select [BRIGHTNESS] option.
3. Use
or
button to set the bright level.
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 21
Exposure Settings
LANGUAGE
CAMERA ID
EXPOSURE
WHITE BAL
DAY/NIGHT
MOTION DET
PRIVACY MASK
SPECIAL
INITIAL SET
EXIT
BRIGHTNESS
AGC MAX
SHUTTER
FLIKERLESS
BLC/WDR
LEVEL
AREA
SPECIAL
INITIAL SET
RETURN
Automatic Gain Control (AGC) setting
MENU
ENGLISH
OFF
If the images are too dark, change the maximum [AGC] value to
make the images lighter.
PUSH AUTO
AUTO
OFF
1. Select [EXPOSURE] option on the [MENU] screen then press
, , or
button. The EXPOSURE menu appears.
2. Use
OFF
EXPOSURE
MEDIUM
AUTO
OFF
OFF
OFF
+
or
button to select [AGC MAX] option.
3. Use
or
button to select a mode.
OFF: AGC is not operated.
HIGH: Applies AGC with high-level.
MEDIUM: Applies AGC with middle-level.
LOW: Applies AGC with low-level.
ON
21
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 22
Exposure Settings
LANGUAGE
CAMERA ID
EXPOSURE
WHITE BAL
DAY/NIGHT
MOTION DET
PRIVACY MASK
SPECIAL
INITIAL SET
EXIT
BRIGHTNESS
AGC MAX
SHUTTER
FLIKERLESS
BLC/WDR
LEVEL
AREA
SPECIAL
INITIAL SET
RETURN
22
Shutter Speed Setting (SHUTTER)
MENU
ENGLISH
OFF
Note: When [FLICKERLESS] option is set to [ON] on the [EXPOSURE]
menu, this item is not available.
PUSH AUTO
AUTO
OFF
1. Select [EXPOSURE] option on the [MENU] screen then press
, , or
button. The EXPOSURE menu appears.
2. Use
OFF
or
button to select [SHUTTER] option.
3. Use
or
button to set shutter speed.
(AUTO, AUTO X2 - X320, FIX X2 - X320, 1/60 - 1/50000)
EXPOSURE
MEDIUM
AUTO
OFF
OFF
OFF
ON
+
Flickerless Setting (FLIKERLESS)
Use for removing the flicker of picture.
1. Select [EXPOSURE] option on the [MENU] screen then press
, , or
button. The EXPOSURE menu appears.
2. Use
or
button to select [FLICKERLESS] option.
3. Use
or
button to set between [ON] or [OFF].
Set to [ON] to remove the flicker.
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 23
Exposure Settings
LANGUAGE
CAMERA ID
EXPOSURE
WHITE BAL
DAY/NIGHT
MOTION DET
PRIVACY MASK
SPECIAL
INITIAL SET
EXIT
BRIGHTNESS
AGC MAX
SHUTTER
FLIKERLESS
BLC/WDR
LEVEL
AREA
SPECIAL
INITIAL SET
RETURN
You can set the exposure options using the [EXPOSURE] menu.
MENU
ENGLISH
OFF
BLC/WDR Setting
PUSH AUTO
AUTO
OFF
Use [BLC/WDR] option to set the options for BLC or WDR camera.
1. Select [EXPOSURE] option on the [MENU] screen then press
, , or
button. The EXPOSURE menu appears.
OFF
EXPOSURE
MEDIUM
AUTO
OFF
BLC1
OFF
ON
2. Use
or
button to select [BLC/WDR] option.
3. Use
or
button to select a mode.
(BLC1, BLC2, USER, WDR, OFF)
+
BLC 1 - 2 (Auto back light compensation): If you use an ordinary camera when there is an intense and concentrated illumination behind an object, the back light will shade the image on
the monitor screen. The BLC function prevents such a back light
effect to secure a clear image under all illumination environments.
(Continued b)
23
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 24
Exposure Settings
BRIGHTNESS
AGC MAX
SHUTTER
FLIKERLESS
BLC/WDR
LEVEL
AREA
SPECIAL
INITIAL SET
RETURN
BRIGHTNESS
AGC MAX
SHUTTER
FLIKERLESS
BLC/WDR
LEVEL
AREA
SPECIAL
INITIAL SET
RETURN
24
EXPOSURE
MEDIUM
AUTO
OFF
USER
BOTTOM
USER: You can use the user setting for BLC level and BLC area.
+
+
• LEVEL: Select a user BLC level to prevent such a back light
effect to secure a clear image.
• AREA: Select a user area to prevent such a back light effect
to secure a clear image. (BOTTOM, TOP, LEFT, RIGHT, and CENTER.)
ON
EXPOSURE
MEDIUM
AUTO
OFF
WDR
OFF
ON
+
WDR: The WDR camera is state of the art to enlarge the screen
profit effectively, especially for taking photos of a window in a
building. In short it revives both the indoor and outdoor status
as they are clearly.
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 25
White Balance Settings
LANGUAGE
CAMERA ID
EXPOSURE
WHITE BAL
DAY/NIGHT
MOTION DET
PRIVACY MASK
SPECIAL
INITIAL SET
EXIT
MENU
ENGLISH
OFF
You can set the white balance options using the [WHITE BALANCE]
menu.
1. Select [WHITE BAL] option on the [MENU] screen.
PUSH AUTO
AUTO
OFF
2. Press ,
appears.
OFF
3. To reset the [WHITE BALANCE] settings to factory setting, select
[INITIAL SET] option then press
on the [WHITE BALANCE]
menu.
WHITE BALANCE
WB MODE
ATW
RED ADJ
BLUE ADJ
INITIAL SET
ON
RETURN
, or
button and the WHITE BALANCE menu
4. To return to the previous menu, select [RETURN] option then
press .
25
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 26
White Balance Settings
LANGUAGE
CAMERA ID
EXPOSURE
WHITE BAL
DAY/NIGHT
MOTION DET
PRIVACY MASK
SPECIAL
INITIAL SET
EXIT
MENU
ENGLISH
OFF
ATW
AUTO
OFF
OFF
WHITE BALANCE
WB MODE
ATW
RED ADJ
BLUE ADJ
INITIAL SET
ON
RETURN
Setting the WB (White Balance) Mode
You can select one of three modes for white balance adjustment as
follows:
1. Select [WHITE BALANCE ] option on the [MENU] screen then
press , , or
button. The WHITE BALANCE menu appears.
2. Use
or
3. Use
or
ance.
button to select [WB MODE] option.
button to select one of three modes for white bal-
ATW (Auto-Tracing White Balance): In this mode, the color temperature is monitored continuously and thereby white balance is
automatically set. The color temperature range for the proper
white balance is approximately 2 500 - 9 500K. Proper white
balance may not be obtained under the following conditions:
1) The color temperature is out of the 2 500 - 9 500K range.
2) When the scene contains mostly high color temperature
objects, such as a blue sky or sunset.
3) When the scene is dim.
(Continued b)
26
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 27
White Balance Settings
PUSH AUTO: If you select the PUSH AUTO mode in the WHITE
BALANCE menu, you will be able to set up the White Balance
automatically using
button; press and hold
button then
release.
WHITE BALANCE
WB MODE
PUSH AUTO
RED ADJ
BLUE ADJ
INITIAL SET
ON
RETURN
MANUAL: You can set the white balance options manually.
• RED ADJ: Obtains the optimum amount of red gain.
• BLUE ADJ: Obtains the optimum amount of blue gain.
WHITE BALANCE
WB MODE
MANUAL
RED ADJ
BLUE ADJ
INITIAL SET
ON
RETURN
+
+
27
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 28
Day/Night Setting
LANGUAGE
CAMERA ID
EXPOSURE
WHITE BAL
DAY/NIGHT
MOTION DET
PRIVACY MASK
SPECIAL
INITIAL SET
EXIT
MENU
ENGLISH
OFF
ATW
AUTO
OFF
OFF
It is a function of a color camera to delete the filter with the IR Cut
function in an illumination below the standard value so that it has a
better sensitivity.
1. Select [DAY/NIGHT] option on the [MENU] screen.
2. Use
or
function.
button to select one of four modes for day/night
AUTO: The camera selects black and white mode if the picture is
dark, or color mode if the picture is bright enough.
EXT : Switches between color picture and black-and-white picture when an external day/night switching signal is received.
NIGHT: Black-and-white mode enabled.
DAY: Color mode enabled.
Note:
The AUTO mode is not available if AGC mode is set to [OFF] or
SHUTTER mode is set to a fixed mode.
28
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 29
Motion Detector Setting (MOTION DET)
LANGUAGE
CAMERA ID
EXPOSURE
WHITE BAL
DAY/NIGHT
MOTION DET
PRIVACY MASK
SPECIAL
INITIAL SET
EXIT
The motion detector detects the moving objects in the scene by
monitoring changes in brightness level. You can select the level of
sensitivity for motion detection.
MENU
ENGLISH
OFF
When this camera is connected to a compatible intelligent CCTV
system, the camera transmits an alarm signal by multiplexing it with
the video signal.
ATW
AUTO
OFF
1. Select [MOTION DET] option on the [MENU] screen.
OFF
MOTION DETECT
SENSITIVITY
AREA
OFF
INITIAL SET
OFF
EXIT
2. Press ,
appears.
, or
button and the MOTION DETECT menu
3. Use [SENSITIVITY] option to obtain the optimum detection level
(7 levels).
+
4. Use [AREA] option to select an area for motion detection.
5. To reset the [MOTION DETECT] settings to factory setting, select
[INITIAL SET] option then press
on the [MOTION DETECT]
menu.
6. To return to the previous menu, select [RETURN] option then
press .
29
LVC-SX701PC_AABBSL_ENG
5/20/06
9:47 AM
Page 30
Motion Detector Setting (MOTION DET)
7/15
This camera has an alarm function. When the picture changes, the
internal switch is closed.
TOP
4/15
LEFT
CENTER RIGHT
BOTTOM
4/15
1/3
1/3
1/3
Detection Area
Vcc
OPEN
OPEN
Alarm
Out
• Sensitivity
Motion is detected when the accumulated value of changed
brightness level exceeds 10% (MEDIUM mode) of reference in
more than one area.
• Condition
The alarm function performs after 10 seconds when the camera is
turned on.
• Caution
Motion detection malfunctions under the following situations.
Please note the conditions below.
- If shooting an object under flickering fluorescent.
- If leaves or curtains are swayed by the wind.
CLOSE
0
1. The period of motion.
2. The hold time is 1 sec.
30
• Alarm keep low for 1 second after the end of moving picture.
• This function which is Motion Detection & Sensitivity has not
been evaluated by UL.
LVC-SX701PC_AABBSL_ENG
5/20/06
9:48 AM
Page 31
Privacy Masking Setting
MENU
LANGUAGE
ENGLISH
CAMERA ID
OFF
EXPOSURE
WHITE BAL
ATW
DAY/NIGHT
AUTO
MOTION DET
OFF
PRIVACY MASK
SPECIAL
INITIAL SET
OFF
PRIVACY MASKING
EXIT
PRIVACY-1
OFF
PRIVACY-2
OFF
PRIVACY-3
OFF
PRIVACY-4
OFF
PRIVACY-5
OFF
PRIVACY-6 MASK ADJUST
OFF
H
POSITION
PRIVACY-7
OFF
V
POSITION
PRIVACY-8
OFF
H
SIZE SET
INITIAL
OFF
V
SIZE
RETURN
RETURN
This function is aiming at the protection of personal privacy, selecting a screen part black not to be displayed in the screen. This function permits the control of the strength level in 8 levels. You may
setup the size and location of the area.
1. Select [PRIVACY MASK] option on the [MENU] screen.
2. Press ,
appears.
, or
button and the PRIVACY MASKING menu
3. Use
or
button to select a privacy number then press
, or
button. The MASK ADJUST menu appears.
,
4. Use
or
to select an option then use , or
button to
adjust the option.
• H POSITION: Moves height position of the mask.
• V POSITION: Moves vertical position of the mask.
• H SIZE: Enlarge or increase the height size of the mask.
• V SIZE: Enlarge or increase the vertical size of the mask.
5. To return to the previous menu, select [RETURN] option then
press .
31
LVC-SX701PC_AABBSL_ENG
5/20/06
9:48 AM
Page 32
Special Menu Settings
LANGUAGE
CAMERA ID
EXPOSURE
WHITE BAL
DAY/NIGHT
MOTION DET
PRIVACY MASK
SPECIAL
INITIAL SET
EXIT
1. Select [SPECIAL] option on the [MENU] screen.
ATW
AUTO
OFF
2. Press
,
, or
button and the SPECIAL menu appears.
3. Use
or
to select an option then use
adjust the option.
OFF
SPECIAL
EFFECT
OFF
D-ZOOM
USER TITLE
SX-700
TITLE DISP
OFF
HOT KEY
NEGA
SYNC
INT
PHASE SHIFT
000
PIX MAPPING
OFF
INITIAL SET
ON
EXIT
32
This menu lets you adjust and set up EFFECT, D-ZOOM, USER TITLE,
TITLE DISP, and SYNC function by yourself in the SPECIAL menu.
MENU
ENGLISH
OFF
, or
button to
4. To reset the [MOTION DETECT] settings to factory setting, select
[INITIAL SET] option then press
on the [MOTION DETECT]
menu.
5. To return to the previous menu, select [RETURN] option then
press .
+
LVC-SX701PC_AABBSL_ENG
5/20/06
9:48 AM
Page 33
Special Menu Settings
LANGUAGE
CAMERA ID
EXPOSURE
WHITE BAL
DAY/NIGHT
MOTION DET
PRIVACY MASK
SPECIAL
INITIAL SET
EXIT
Setting the digital effect (EFFECT)
MENU
ENGLISH
OFF
You can select the digital effect.
1. Select [SPECIAL] option on the [MENU] screen.
ATW
AUTO
OFF
OFF
2. Press
,
, or
button and the SPECIAL menu appears.
3. Use
or
to select [EFFECT] option
4. Use
or
button to select a digital effect.
• [NEGA]: Turn on the negative effect.
• [B/W]: The picture will be displayed with grayscale.
• [V-FLIP]: Flip the picture vertically.
SPECIAL
EFFECT
OFF
D-ZOOM
USER TITLE
SX-700
TITLE DISP
OFF
HOT KEY
NEGA
SYNC
INT
PHASE SHIFT
000
PIX MAPPING
OFF
INITIAL SET
ON
EXIT
• [MIRROR]: Turn on the mirror effect.
+
• [ROTATE]: Rotate the picture. (180°)
• [FREEZE]: Freeze the picture.
• [OFF]: Turn off the digital effect.
33
LVC-SX701PC_AABBSL_ENG
5/20/06
9:48 AM
Page 34
Special Menu Settings
LANGUAGE
CAMERA ID
EXPOSURE
WHITE BAL
DAY/NIGHT
MOTION DET
PRIVACY MASK
SPECIAL
INITIAL SET
EXIT
Setting the digital zoom (D-ZOOM)
MENU
ENGLISH
OFF
You can select the digital zoom level.
This function is not available when the BLC/WDR option is set to
WDR or EFFECT option is set to FREEZE.
1. Select [SPECIAL] option on the [MENU] screen.
ATW
AUTO
OFF
OFF
2. Press
,
3. Use
or
, or
to select [D-ZOOM] option
button and the SPECIAL menu appears.
4. Use
or
button to select a digital zoom level (7 level).
Naming the camera (USER-TITLE)
SPECIAL
EFFECT
OFF
D-ZOOM
USER TITLE
SX-700
TITLE DISP
OFF
HOT KEY
NEGA
SYNC
INT
PHASE SHIFT
000
PIX MAPPING
OFF
INITIAL SET
ON
EXIT
34
+
You can name the camera independently.
1. Follow steps 1-2 as shown above.
2. Use
or
to select [USER TITLE] option
The first character of the name will blink.
3. Use
or
button to select a character for the first character
then press
button. The second character blink.
4. Repeat step 3 to set the remain characters.
LVC-SX701PC_AABBSL_ENG
5/20/06
9:48 AM
Page 35
Special Menu Settings
LANGUAGE
CAMERA ID
EXPOSURE
WHITE BAL
DAY/NIGHT
MOTION DET
PRIVACY MASK
SPECIAL
INITIAL SET
EXIT
Setting the title display
MENU
ENGLISH
OFF
The onscreen display of camera’s name can be turned on or off.
1. Select [SPECIAL] option on the [MENU] screen.
ATW
AUTO
OFF
OFF
2. Press
,
3. Use
or
, or
button and the SPECIAL menu appears.
to select [TITLE DISP] option
4. Use
or
button to select [ON] or [OFF].
Set to [ON] and the camera’s name appears on the screen.
Setting the HOT KEY
SPECIAL
EFFECT
OFF
D-ZOOM
USER TITLE
SX-700
TITLE DISP
OFF
HOT KEY
NEGA
SYNC
INT
PHASE SHIFT
000
PIX MAPPING
OFF
INITIAL SET
ON
EXIT
+
You can set the HOT KEY function for signal from MULTI INPUT
terminal. This function is fixed to [DAY/NIGHT] when DAY/NIGHT
option is set to [EXT].
1. Follow steps 1-2 as shown above.
2. Use
or
to select [TITLE DISP] option
3. Use
or
button to select a function.
(NEGA, B/W, V-FLIP, MIRROR, ROTATE, FREEZE, or OFF)
35
LVC-SX701PC_AABBSL_ENG
5/20/06
9:48 AM
Page 36
Special Menu Settings
LANGUAGE
CAMERA ID
EXPOSURE
WHITE BAL
DAY/NIGHT
MOTION DET
PRIVACY MASK
SPECIAL
INITIAL SET
EXIT
You can select internal sync (INT) mode or line-lock (LINE) mode.
The SYNC function is available only with AC power source.
ATW
AUTO
OFF
1. Select [SPECIAL] option on the [MENU] screen.
2. Press
,
OFF
3. Use
or
SPECIAL
EFFECT
OFF
D-ZOOM
USER TITLE
SX-700
TITLE DISP
OFF
HOT KEY
NEGA
SYNC
INT
PHASE SHIFT
000
PIX MAPPING
OFF
INITIAL SET
ON
EXIT
36
Synchronization Setting (SYNC)
MENU
ENGLISH
OFF
+
, or
button and the SPECIAL menu appears.
to select [SYNC] option.
4. Use
or
button to select [INT] or [LL] (Line Lock).
[INT]: Selects for using the internal synchronization.
[LL] (Line Lock): Selects for the operation of multi cameras
because it synchronizes the camera phase by using the
external signal (AC Signal). A little phase deviation for some
sets may be aligned.
5. Use
or
to select [PHASE SHIFT] option.
6. Use
or
button to select phase range.
The PHASE ranges are from 0 to 524.
LVC-SX701PC_AABBSL_ENG
5/20/06
9:48 AM
Page 37
Special Menu Settings
LANGUAGE
CAMERA ID
EXPOSURE
WHITE BAL
DAY/NIGHT
MOTION DET
PRIVACY MASK
SPECIAL
INITIAL SET
EXIT
Setting the Pix Mapping
MENU
ENGLISH
OFF
You can improve the picture quality with this function that compensate damaged pixels.
ATW
AUTO
OFF
1. Select [SPECIAL] option on the [MENU] screen.
2. Press
,
OFF
3. Use
or
to select [PIX MAPPING] option.
4. Use
or
button to select [ON] or [OFF].
SPECIAL
EFFECT
OFF
D-ZOOM
USER TITLE
SX-700
TITLE DISP
OFF
HOT KEY
NEGA
SYNC
INT
PHASE SHIFT
000
PIX MAPPING
OFF
INITIAL SET
ON
EXIT
, or
button and the SPECIAL menu appears.
Caution
If you are using manual lens, block the lens before using this function.
+
37
LVC-SX701PC_AABBSL_ENG
5/20/06
9:48 AM
Page 38
RS-485 Protocol
Data Communication Format
•
•
•
•
Commands
Data Length: 1 Byte (8 Bit)
Start/Stop Bit: 1 BIT
Parity Bit: None
Baud rate: 9,600 bps
Function
Format
BYTE 1
BYTE 2
BYTE 3
BYTE 4
BYTE 5
BYTE 6
0xC5
CODE1
CODE2
CODE3
CAM_ID
*C.S.
*C.S. = Check Sum
• The data of total 6 bytes is transmitted from the
external RS-485 device to the camera.
• BYTE 6 : The value of Check Sum from ‘BYTE 1 ’
to ‘BYTE 5 ’.
ex) In case of transmission, 0xC5, 0x5F, 0x02,
0x00, 0x0A”
C.S. = 0xC5 +0x5F +0x02 +0x00 +0x0A = 0x0130
therefore, C.S. = 0x30
38
Command
(external device → camera)
OSD Menu ON/OFF 0xC5, 0x5F, 0x25, 0x00, ID, C.S.
LEFT Button
0xC5, 0x5F, 0x38, 0x00, ID, C.S.
Right Button
0xC5, 0x5F, 0x39, 0x00, ID, C.S.
Up Button
0xC5, 0x5F, 0x02, 0x00, ID, C.S.
Down Button
0xC5, 0x5F, 0x04, 0x00, ID, C.S.
Menu Button
0xC5, 0x5F, 0x24, 0x00, ID, C.S.
• You must send “Stop” command to camera after
sending each command described above.
The “Stop” command is “0xC5, 0x5F, 0x0C, 0x00,
ID, C.S.”.
LVC-SX701PC_AABBSL_ENG
5/20/06
9:48 AM
Page 39
Specifications
Total/Effective Pixels
Pick-up Device
Lens
Iris
Signal Process
Scanning System
Synchronization System
Scanning Frequency
Resolution
S/N Ratio
Standard Illuminance
(1/3 Video Output)
Video Output Signal
Auto Gain Control
Exposure
410K/380K Pixels
1/3” Interline Color CCD
C/CS Mount
DC/ELC/VIDEO Selectable
Digital Signal Process
2:1 Interface
Internal/Line Lock
59.94 Hz (VD)
540 Lines
More than 52 dB (AGC Off)
Day: 0.001 (0.3: DSS Off) Lux
Night: 0.0001 (0.02: DSS Off) Lux
1.0 Vp-p Composite Signal (75 Ω)
Off/Low/Medium/High
Automatic Control with DC/Video Iris meter/ Electronic Light
39
LVC-SX701PC_AABBSL_ENG
5/20/06
9:48 AM
Page 40
Specifications
Electric Shutter
White Balance
Back Light
Motion Detection:
Power Consumption
Operation Temperature
Storage Temperature
Weight
Dimension (H x V x D)
40
1/60 - 1/100,000 (Auto Mode)
ATW/PUSH AUTO/MANUAL
OFF/BLC1/BLC2/USER/WDR
OFF/ON (Area, Sensitivity)
Less than 6W
-10ºC - 50ºC (Humidity: 0%RH - 80%RH)
-20ºC - 60ºC (Humidity: 0%RH - 85%RH)
250g
67.1 x 59 x 127.5 mm
LVC-SX701PC_AABBSL_ENG
P/NO : 3834RS0075Q
5/20/06
9:48 AM
Page 41